Limit on the number of simultaneously opened zones per single thread/process.
.TP
.BI ignore_zone_limits \fR=\fPbool
-If this isn't set, fio will query the max open zones limit from the zoned block
-device, and exit if the specified \fBmax_open_zones\fR value is larger than the
-limit reported by the device. Default: false.
+If this option is used, fio will ignore the maximum number of open zones limit
+of the zoned block device in use, thus allowing the option \fBmax_open_zones\fR
+value to be larger than the device reported limit. Default: false.
.TP
.BI zone_reset_threshold \fR=\fPfloat
A number between zero and one that indicates the ratio of logical blocks with
.TP
.BI filesize \fR=\fPirange(int)
Individual file sizes. May be a range, in which case fio will select sizes
-for files at random within the given range and limited to \fBsize\fR in
-total (if that is given). If not given, each created file is the same size.
-This option overrides \fBsize\fR in terms of file size, which means
-this value is used as a fixed size or possible range of each file.
+for files at random within the given range. If not given, each created file
+is the same size. This option overrides \fBsize\fR in terms of file size,
+i.e. \fBsize\fR becomes merely the default for \fBio_size\fR (and
+has no effect it all if \fBio_size\fR is set explicitly).
.TP
.BI file_append \fR=\fPbool
Perform I/O after the end of the file. Normally fio will operate within the
unit access (fua) flag. Default: 0.
.TP
.BI (sg)sg_write_mode \fR=\fPstr
-Specify the type of write commands to issue. This option can take three
+Specify the type of write commands to issue. This option can take multiple
values:
.RS
.RS
.B write (default)
Write opcodes are issued as usual
.TP
+.B write_and_verify
+Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 00b. This directs the
+device to carry out a medium verification with no data comparison for the data
+that was written. The writefua option is ignored with this selection.
+.TP
.B verify
-Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 0. This
-directs the device to carry out a medium verification with no data
-comparison. The writefua option is ignored with this selection.
+This option is deprecated. Use write_and_verify instead.
.TP
-.B same
+.B write_same
Issue WRITE SAME commands. This transfers a single block to the device
and writes this same block of data to a contiguous sequence of LBAs
beginning at the specified offset. fio's block size parameter
generate 8k of data for each command butonly the first 512 bytes will
be used and transferred to the device. The writefua option is ignored
with this selection.
+.TP
+.B same
+This option is deprecated. Use write_same instead.
+.TP
+.B write_same_ndob
+Issue WRITE SAME(16) commands as above but with the No Data Output
+Buffer (NDOB) bit set. No data will be transferred to the device with
+this bit set. Data written will be a pre-determined pattern such as
+all zeroes.
+.TP
+.B write_stream
+Issue WRITE STREAM(16) commands. Use the stream_id option to specify
+the stream identifier.
+.TP
+.B verify_bytchk_00
+Issue VERIFY commands with BYTCHK set to 00. This directs the device to carry
+out a medium verification with no data comparison.
+.TP
+.B verify_bytchk_01
+Issue VERIFY commands with BYTCHK set to 01. This directs the device to
+compare the data on the device with the data transferred to the device.
+.TP
+.B verify_bytchk_11
+Issue VERIFY commands with BYTCHK set to 11. This transfers a single block to
+the device and compares the contents of this block with the data on the device
+beginning at the specified offset. fio's block size parameter specifies the
+total amount of data compared with this command. However, only one block
+(sector) worth of data is transferred to the device. This is similar to the
+WRITE SAME command except that data is compared instead of written.
.RE
.RE
.TP
+.BI (sg)stream_id \fR=\fPint
+Set the stream identifier for WRITE STREAM commands. If this is set to 0 (which is not
+a valid stream identifier) fio will open a stream and then close it when done. Default
+is 0.
+.TP
.BI (nbd)uri \fR=\fPstr
Specify the NBD URI of the server to test.
The string is a standard NBD URI (see
projects / fio.git / blobdiff