.RS
.TP
.B none
-The \fBzonerange\fR, \fBzonesize\fR and \fBzoneskip\fR parameters are ignored.
+The \fBzonerange\fR, \fBzonesize\fR \fBzonecapacity\fR and \fBzoneskip\fR
+parameters are ignored.
.TP
.B strided
I/O happens in a single zone until \fBzonesize\fR bytes have been transferred.
After that number of bytes has been transferred processing of the next zone
-starts.
+starts. The \fBzonecapacity\fR parameter is ignored.
.TP
.B zbd
Zoned block device mode. I/O happens sequentially in each zone, even if random
device zone size. For a regular block device or file, the specified
\fBzonesize\fR must be at least 512B.
.TP
+.BI zonecapacity \fR=\fPint
+For \fBzonemode\fR=zbd, this defines the capacity of a single zone, which is
+the accessible area starting from the zone start address. This parameter only
+applies when using \fBzonemode\fR=zbd in combination with regular block devices.
+If not specified it defaults to the zone size. If the target device is a zoned
+block device, the zone capacity is obtained from the device information and this
+option is ignored.
+.TP
.BI zoneskip \fR=\fPint
For \fBzonemode\fR=strided, the number of bytes to skip after \fBzonesize\fR
bytes of data have been transferred.
will perform I/O within the first 20GiB but exit when 5GiB have been
done. The opposite is also possible \-\- if \fBsize\fR is set to 20GiB,
and \fBio_size\fR is set to 40GiB, then fio will do 40GiB of I/O within
-the 0..20GiB region.
+the 0..20GiB region. Value can be set as percentage: \fBio_size\fR=N%.
+In this case \fBio_size\fR multiplies \fBsize\fR= value.
.TP
.BI filesize \fR=\fPirange(int)
Individual file sizes. May be a range, in which case fio will select sizes
single CPU at the desired rate. A job never finishes unless there is
at least one non-cpuio job.
.TP
-.B guasi
-The GUASI I/O engine is the Generic Userspace Asynchronous Syscall
-Interface approach to async I/O. See \fIhttp://www.xmailserver.org/guasi-lib.html\fR
-for more info on GUASI.
-.TP
.B rdma
The RDMA I/O engine supports both RDMA memory semantics
(RDMA_WRITE/RDMA_READ) and channel semantics (Send/Recv) for the
can increase latencies. The benefit is that fio can manage submission rates
independently of the device completion rates. This avoids skewed latency
reporting if I/O gets backed up on the device side (the coordinated omission
-problem).
+problem). Note that this option cannot reliably be used with async IO engines.
.SS "I/O rate"
.TP
.BI thinktime \fR=\fPtime
You can specify a number of files by separating the names with a ':' character.
See the \fBfilename\fR option for information on how to escape ':'
characters within the file names. These files will be sequentially assigned to
-job clones created by \fBnumjobs\fR.
+job clones created by \fBnumjobs\fR. '-' is a reserved name, meaning read from
+stdin, notably if \fBfilename\fR is set to '-' which means stdin as well,
+then this flag can't be set to '-'.
.TP
.BI read_iolog_chunked \fR=\fPbool
Determines how iolog is read. If false (default) entire \fBread_iolog\fR will
flow. See \fBflow\fR.
.TP
.BI flow \fR=\fPint
-Weight in token-based flow control. If this value is used, then there is
-a 'flow counter' which is used to regulate the proportion of activity between
-two or more jobs. Fio attempts to keep this flow counter near zero. The
-\fBflow\fR parameter stands for how much should be added or subtracted to the
-flow counter on each iteration of the main I/O loop. That is, if one job has
-`flow=8' and another job has `flow=\-1', then there will be a roughly 1:8
-ratio in how much one runs vs the other.
-.TP
-.BI flow_watermark \fR=\fPint
-The maximum value that the absolute value of the flow counter is allowed to
-reach before the job must wait for a lower value of the counter.
+Weight in token-based flow control. If this value is used,
+then fio regulates the activity between two or more jobs
+sharing the same flow_id.
+Fio attempts to keep each job activity proportional to other jobs' activities
+in the same flow_id group, with respect to requested weight per job.
+That is, if one job has `flow=3', another job has `flow=2'
+and another with `flow=1`, then there will be a roughly 3:2:1 ratio
+in how much one runs vs the others.
.TP
.BI flow_sleep \fR=\fPint
-The period of time, in microseconds, to wait after the flow watermark has
-been exceeded before retrying operations.
+The period of time, in microseconds, to wait after the flow counter
+has exceeded its proportion before retrying operations.
.TP
.BI stonewall "\fR,\fB wait_for_previous"
Wait for preceding jobs in the job file to exit, before starting this
one. Can be used to insert serialization points in the job file. A stone
wall also implies starting a new reporting group, see
-\fBgroup_reporting\fR.
+\fBgroup_reporting\fR. Optionally you can use `stonewall=0` to disable or
+`stonewall=1` to enable it.
.TP
.BI exitall
By default, fio will continue running all other jobs when one job finishes.
make fio terminate all jobs in the same group, as soon as one job of that
group finishes.
.TP
-.BI exit_what
+.BI exit_what \fR=\fPstr
By default, fio will continue running all other jobs when one job finishes.
-Sometimes this is not the desired action. Setting \fBexit_all\fR will instead
+Sometimes this is not the desired action. Setting \fBexitall\fR will instead
make fio terminate all jobs in the same group. The option \fBexit_what\fR
-allows to control which jobs get terminated when \fBexitall\fR is enabled. The
-default is \fBgroup\fR and does not change the behaviour of \fBexitall\fR. The
-setting \fBall\fR terminates all jobs. The setting \fBstonewall\fR terminates
-all currently running jobs across all groups and continues execution with the
-next stonewalled group.
+allows you to control which jobs get terminated when \fBexitall\fR is enabled.
+The default value is \fBgroup\fR.
+The allowed values are:
+.RS
+.RS
+.TP
+.B all
+terminates all jobs.
+.TP
+.B group
+is the default and does not change the behaviour of \fBexitall\fR.
+.TP
+.B stonewall
+terminates all currently running jobs across all groups and continues
+execution with the next stonewalled group.
+.RE
+.RE
.TP
.BI exec_prerun \fR=\fPstr
Before running this job, issue the command specified through
and IOPS. The logs share a common format, which looks like this:
.RS
.P
-time (msec), value, data direction, block size (bytes), offset (bytes)
+time (msec), value, data direction, block size (bytes), offset (bytes),
+command priority
.RE
.P
`Time' for the log entry is always in milliseconds. The `value' logged depends
from the start of the file for that particular I/O. The logging of the offset can be
toggled with \fBlog_offset\fR.
.P
+`Command priority` is 0 for normal priority and 1 for high priority. This is controlled
+by the ioengine specific \fBcmdprio_percentage\fR.
+.P
Fio defaults to logging every individual I/O but when windowed logging is set
through \fBlog_avg_msec\fR, either the average (by default) or the maximum
(\fBlog_max_value\fR is set) `value' seen over the specified period of time
projects / fio.git / blobdiff