may override any parameter set in global sections.
.SH "JOB PARAMETERS"
.SS Types
-Some parameters may take arguments of a specific type. The types used are:
+Some parameters may take arguments of a specific type.
+Anywhere a numeric value is required, an arithmetic expression may be used,
+provided it is surrounded by parentheses. Supported operators are:
+.RS
+.RS
+.TP
+.B addition (+)
+.TP
+.B subtraction (-)
+.TP
+.B multiplication (*)
+.TP
+.B division (/)
+.TP
+.B modulus (%)
+.TP
+.B exponentiation (^)
+.RE
+.RE
+.P
+For time values in expressions, units are microseconds by default. This is
+different than for time values not in expressions (not enclosed in
+parentheses). The types used are:
.TP
.I str
String: a sequence of alphanumeric characters.
If set, fio will fill the IO buffers with this pattern. If not set, the contents
of IO buffers is defined by the other options related to buffer contents. The
setting can be any pattern of bytes, and can be prefixed with 0x for hex
-values.
+values. It may also be a string, where the string must then be wrapped with
+"".
+.TP
+.BI dedupe_percentage \fR=\fPint
+If set, fio will generate this percentage of identical buffers when writing.
+These buffers will be naturally dedupable. The contents of the buffers depend
+on what other buffer compression settings have been set. It's possible to have
+the individual buffers either fully compressible, or not at all. This option
+only controls the distribution of unique buffers.
.TP
.BI nrfiles \fR=\fPint
Number of files to use for this job. Default: 1.
set by \fBsize\fR, or if it exhaust the allocated time (or hits an error
condition). With this setting, the range/size can be set independently of
the number of IOs to perform. When fio reaches this number, it will exit
-normally and report status.
+normally and report status. Note that this does not extend the amount
+of IO that will be done, it will only stop fio if this condition is met
+before other end-of-job criteria.
.TP
.BI fsync \fR=\fPint
How many I/Os to perform before issuing an \fBfsync\fR\|(2) of dirty data. If
used and must be omitted unless it is a valid UDP multicast address.
.TP
.BI (net,netsplice)port \fR=\fPint
-The TCP or UDP port to bind to or connect to.
+The TCP or UDP port to bind to or connect to. If this is used with
+\fBnumjobs\fR to spawn multiple instances of the same job type, then
+this will be the starting port number since fio will use a range of ports.
.TP
.BI (net,netsplice)interface \fR=\fPstr
The IP address of the network interface used to send or receive UDP multicast
send back. For UDP multicast traffic pingpong=1 should only be set for a single
reader when multiple readers are listening to the same address.
.TP
+.BI (net, window_size) \fR=\fPint
+Set the desired socket buffer size for the connection.
+.TP
+.BI (net, mss) \fR=\fPint
+Set the TCP maximum segment size (TCP_MAXSEG).
+.TP
.BI (e4defrag,donorname) \fR=\fPstr
File will be used as a block donor (swap extents between files)
.TP
You can connect to multiple clients as well, to do that you could run:
fio \-\-client=server2 \-\-client=server2 <job file(s)>
+
+If the job file is located on the fio server, then you can tell the server
+to load a local file as well. This is done by using \-\-remote-config:
+
+fio \-\-client=server \-\-remote-config /path/to/file.fio
+
+Then the fio serer will open this local (to the server) job file instead
+of being passed one from the client.
.SH AUTHORS
.B fio
projects / fio.git / blobdiff