parsed and used.
.TP
.BI \-\-alloc\-size \fR=\fPkb
-Set the internal smalloc pool size to \fIkb\fR in KiB. The
-\fB\-\-alloc\-size\fR switch allows one to use a larger pool size for smalloc.
+Allocate additional internal smalloc pools of size \fIkb\fR in KiB. The
+\fB\-\-alloc\-size\fR option increases shared memory set aside for use by fio.
If running large jobs with randommap enabled, fio can run out of memory.
Smalloc is an internal allocator for shared structures from a fixed size
memory pool and can grow to 16 pools. The pool size defaults to 16MiB.
.RE
.TP
.BI zonerange \fR=\fPint
-Size of a single zone. See also \fBzonesize\fR and \fBzoneskip\fR.
+For \fBzonemode\fR=strided, this is the size of a single zone. See also
+\fBzonesize\fR and \fBzoneskip\fR.
+
+For \fBzonemode\fR=zbd, this parameter is ignored.
.TP
.BI zonesize \fR=\fPint
For \fBzonemode\fR=strided, this is the number of bytes to transfer before
will be accessed. If this parameter is larger than \fBzonerange\fR then each
zone will be accessed multiple times before skipping to the next zone.
-For \fBzonemode\fR=zbd, this is the size of a single zone. The \fBzonerange\fR
-parameter is ignored in this mode.
+For \fBzonemode\fR=zbd, this is the size of a single zone. The
+\fBzonerange\fR parameter is ignored in this mode. For a job accessing a
+zoned block device, the specified \fBzonesize\fR must be 0 or equal to the
+device zone size. For a regular block device or file, the specified
+\fBzonesize\fR must be at least 512B.
.TP
.BI zoneskip \fR=\fPint
For \fBzonemode\fR=strided, the number of bytes to skip after \fBzonesize\fR
-bytes of data have been transferred. This parameter must be zero for
-\fBzonemode\fR=zbd.
+bytes of data have been transferred.
+
+For \fBzonemode\fR=zbd, the \fBzonesize\fR aligned number of bytes to skip
+once a zone is fully written (write workloads) or all written data in the
+zone have been read (read workloads). This parameter is valid only for
+sequential workloads and ignored for random workloads. For read workloads,
+see also \fBread_beyond_wp\fR.
.TP
.BI read_beyond_wp \fR=\fPbool
zone has a type, e.g. conventional or sequential. A conventional zone can be
written at any offset that is a multiple of the block size. Sequential zones
must be written sequentially. The position at which a write must occur is
-called the write pointer. A zoned block device can be either drive
-managed, host managed or host aware. For host managed devices the host must
-ensure that writes happen sequentially. Fio recognizes host managed devices
-and serializes writes to sequential zones for these devices.
+called the write pointer. A zoned block device can be either host managed or
+host aware. For host managed devices the host must ensure that writes happen
+sequentially. Fio recognizes host managed devices and serializes writes to
+sequential zones for these devices.
If a read occurs in a sequential zone beyond the write pointer then the zoned
block device will complete the read without reading any data from the storage
is incremented for each sub\-job (i.e. when \fBnumjobs\fR option is
specified). This option is useful if there are several jobs which are
intended to operate on a file in parallel disjoint segments, with even
-spacing between the starting points.
+spacing between the starting points. Percentages can be used for this option.
+If a percentage is given, the generated offset will be aligned to the minimum
+\fBblocksize\fR or to the value of \fBoffset_align\fR if provided.
.TP
.BI number_ios \fR=\fPint
Fio will normally perform I/Os until it has exhausted the size of the region
.TP
.BI fdatasync \fR=\fPint
Like \fBfsync\fR but uses \fBfdatasync\fR\|(2) to only sync data and
-not metadata blocks. In Windows, FreeBSD, and DragonFlyBSD there is no
+not metadata blocks. In Windows, FreeBSD, DragonFlyBSD or OSX there is no
\fBfdatasync\fR\|(2) so this falls back to using \fBfsync\fR\|(2).
Defaults to 0, which means fio does not periodically issue and wait for a
data\-only sync to complete.
before IO is started. This eliminates the need to map and release for each IO.
This is more efficient, and reduces the IO latency as well.
.TP
+.BI (io_uring)registerfiles
+With this option, fio registers the set of files being used with the kernel.
+This avoids the overhead of managing file counts in the kernel, making the
+submission and completion part more lightweight. Required for the below
+sqthread_poll option.
+.TP
.BI (io_uring)sqthread_poll
Normally fio will submit IO by issuing a system call to notify the kernel of
available items in the SQ ring. If this option is set, the act of submitting IO
projects / fio.git / blobdiff