Limit on the number of simultaneously opened zones per single thread/process.
.TP
.BI ignore_zone_limits \fR=\fPbool
-If this isn't set, fio will query the max open zones limit from the zoned block
-device, and exit if the specified \fBmax_open_zones\fR value is larger than the
-limit reported by the device. Default: false.
+If this option is used, fio will ignore the maximum number of open zones limit
+of the zoned block device in use, thus allowing the option \fBmax_open_zones\fR
+value to be larger than the device reported limit. Default: false.
.TP
.BI zone_reset_threshold \fR=\fPfloat
A number between zero and one that indicates the ratio of logical blocks with
.BI (io_uring,libaio)cmdprio_percentage \fR=\fPint[,int]
Set the percentage of I/O that will be issued with the highest priority.
Default: 0. A single value applies to reads and writes. Comma-separated
-values may be specified for reads and writes. This option cannot be used
-with the `prio` or `prioclass` options. For this option to be effective,
+values may be specified for reads and writes. For this option to be effective,
NCQ priority must be supported and enabled, and `direct=1' option must be
-used. fio must also be run as the root user.
+used. fio must also be run as the root user. Unlike slat/clat/lat stats, which
+can be tracked and reported independently, per priority stats only track and
+report a single type of latency. By default, completion latency (clat) will be
+reported, if \fBlat_percentiles\fR is set, total latency (lat) will be reported.
.TP
.BI (io_uring,libaio)cmdprio_class \fR=\fPint[,int]
Set the I/O priority class to use for I/Os that must be issued with a
unit access (fua) flag. Default: 0.
.TP
.BI (sg)sg_write_mode \fR=\fPstr
-Specify the type of write commands to issue. This option can take three
+Specify the type of write commands to issue. This option can take multiple
values:
.RS
.RS
.B write (default)
Write opcodes are issued as usual
.TP
+.B write_and_verify
+Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 00b. This directs the
+device to carry out a medium verification with no data comparison for the data
+that was written. The writefua option is ignored with this selection.
+.TP
.B verify
-Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 0. This
-directs the device to carry out a medium verification with no data
-comparison. The writefua option is ignored with this selection.
+This option is deprecated. Use write_and_verify instead.
.TP
-.B same
+.B write_same
Issue WRITE SAME commands. This transfers a single block to the device
and writes this same block of data to a contiguous sequence of LBAs
beginning at the specified offset. fio's block size parameter
generate 8k of data for each command butonly the first 512 bytes will
be used and transferred to the device. The writefua option is ignored
with this selection.
+.TP
+.B same
+This option is deprecated. Use write_same instead.
+.TP
+.B write_same_ndob
+Issue WRITE SAME(16) commands as above but with the No Data Output
+Buffer (NDOB) bit set. No data will be transferred to the device with
+this bit set. Data written will be a pre-determined pattern such as
+all zeroes.
+.TP
+.B write_stream
+Issue WRITE STREAM(16) commands. Use the stream_id option to specify
+the stream identifier.
+.TP
+.B verify_bytchk_00
+Issue VERIFY commands with BYTCHK set to 00. This directs the device to carry
+out a medium verification with no data comparison.
+.TP
+.B verify_bytchk_01
+Issue VERIFY commands with BYTCHK set to 01. This directs the device to
+compare the data on the device with the data transferred to the device.
+.TP
+.B verify_bytchk_11
+Issue VERIFY commands with BYTCHK set to 11. This transfers a single block to
+the device and compares the contents of this block with the data on the device
+beginning at the specified offset. fio's block size parameter specifies the
+total amount of data compared with this command. However, only one block
+(sector) worth of data is transferred to the device. This is similar to the
+WRITE SAME command except that data is compared instead of written.
.RE
.RE
.TP
+.BI (sg)stream_id \fR=\fPint
+Set the stream identifier for WRITE STREAM commands. If this is set to 0 (which is not
+a valid stream identifier) fio will open a stream and then close it when done. Default
+is 0.
+.TP
.BI (nbd)uri \fR=\fPstr
Specify the NBD URI of the server to test.
The string is a standard NBD URI (see
\fBwrite_bw_log\fR for details about the filename format and \fBLOG
FILE FORMATS\fR for how data is structured within the file.
.TP
+.BI log_entries \fR=\fPint
+By default, fio will log an entry in the iops, latency, or bw log for
+every I/O that completes. The initial number of I/O log entries is 1024.
+When the log entries are all used, new log entries are dynamically
+allocated. This dynamic log entry allocation may negatively impact
+time-related statistics such as I/O tail latencies (e.g. 99.9th percentile
+completion latency). This option allows specifying a larger initial
+number of log entries to avoid run-time allocation of new log entries,
+resulting in more precise time-related I/O statistics.
+Also see \fBlog_avg_msec\fR as well. Defaults to 1024.
+.TP
.BI log_avg_msec \fR=\fPint
By default, fio will log an entry in the iops, latency, or bw log for every
I/O that completes. When writing to the disk log, that can quickly grow to a
projects / fio.git / blobdiff