can specify a number of files by separating the names with a
':' colon. So if you wanted a job to open /dev/sda and /dev/sdb
as the two working files, you would use
- filename=/dev/sda:/dev/sdb. If the wanted filename does need to
- include a colon, then escape that with a '\' character. For
- instance, if the filename is "/dev/dsk/foo@3,0:c", then you would
- use filename="/dev/dsk/foo@3,0\:c". '-' is a reserved name,
- meaning stdin or stdout. Which of the two depends on the read/write
- direction set.
+ filename=/dev/sda:/dev/sdb. On Windows, disk devices are accessed
+ as \\.\PhysicalDrive0 for the first device, \\.\PhysicalDrive1
+ for the second etc. If the wanted filename does need to
+ include a colon, then escape that with a '\' character.
+ For instance, if the filename is "/dev/dsk/foo@3,0:c",
+ then you would use filename="/dev/dsk/foo@3,0\:c".
+ '-' is a reserved name, meaning stdin or stdout. Which of the
+ two depends on the read/write direction set.
opendir=str Tell fio to recursively add any file it can find in this
directory and down the file system tree.
fallocate=bool By default, fio will use fallocate() to advise the system
of the size of the file we are going to write. This can be
turned off with fallocate=0. May not be available on all
- supported platforms.
+ supported platforms. If using ZFS on Solaris this must be
+ set to 0 because ZFS doesn't support it.
fadvise_hint=bool By default, fio will use fadvise() to advise the kernel
on what IO patterns it is likely to issue. Sometimes you
and limited to 'size' in total (if that is given). If not
given, each created file is the same size.
-fill_device=bool Sets size to something really large and waits for ENOSPC (no
+fill_device=bool
+fill_fs=bool Sets size to something really large and waits for ENOSPC (no
space left on device) as the terminating condition. Only makes
sense with sequential write. For a read workload, the mount
- point will be filled first then IO started on the result.
+ point will be filled first then IO started on the result. This
+ option doesn't make sense if operating on a raw device node,
+ since the size of that is already known by the file system.
+ Additionally, writing beyond end-of-device will not return
+ ENOSPC there.
blocksize=int
bs=int The block size used for the io units. Defaults to 4k. Values
solarisaio Solaris native asynchronous io.
+ windowsaio Windows native asynchronous io.
+
mmap File is memory mapped and data copied
to/from using memcpy(3).
iodepth=int This defines how many io units to keep in flight against
the file. The default is 1 for each file defined in this
job, can be overridden with a larger value for higher
- concurrency.
+ concurrency. Note that increasing iodepth beyond 1 will not
+ affect synchronous ioengines (except for small degress when
+ verify_async is in use). Even async engines may impose OS
+ restrictions causing the desired depth not to be achieved.
+ This may happen on Linux when using libaio and not setting
+ direct=1, since buffered IO is not async on that OS. Keep an
+ eye on the IO depth distribution in the fio output to verify
+ that the achieved depth is as expected. Default: 1.
iodepth_batch_submit=int
iodepth_batch=int This defines how many pieces of IO to submit at once.
the depth drain down to 4 before starting to fill it again.
direct=bool If value is true, use non-buffered io. This is usually
- O_DIRECT.
+ O_DIRECT. Note that ZFS on Solaris doesn't support direct io.
buffered=bool If value is true, use buffered io. This is the opposite
of the 'direct' option. Defaults to true.
option is set, fio will exit the job on the first observed
failure.
+verify_dump=bool If set, dump the contents of both the original data
+ block and the data block we read off disk to files. This
+ allows later analysis to inspect just what kind of data
+ corruption occurred. On by default.
+
verify_async=int Fio will normally verify IO inline from the submitting
thread. This option takes an integer describing how many
async offload threads to create for IO verification instead,
io on zones of a file.
write_iolog=str Write the issued io patterns to the specified file. See
- read_iolog.
+ read_iolog. Specify a separate file for each job, otherwise
+ the iologs will be interspersed and the file may be corrupt.
read_iolog=str Open an iolog with the specified file name and replay the
io patterns it contains. This can be used to store a
projects / fio.git / blobdiff