set `filesize` so that all the accounting still occurs, but no
actual I/O will be done other than creating the file.
+ **filestat**
+ Simply do stat() and do no I/O to the file. You need to set 'filesize'
+ and 'nrfiles', so that files will be created.
+ This engine is to measure file lookup and meta data access.
+
**libpmem**
Read and write using mmap I/O to a file on a filesystem
mounted with DAX on a persistent memory device through the PMDK
with the caveat that when used on the command line, they must come after the
:option:`ioengine` that defines them is selected.
-.. option:: hipri : [io_uring]
+.. option:: cmdprio_percentage=int : [io_uring] [libaio]
- If this option is set, fio will attempt to use polled IO completions.
- Normal IO completions generate interrupts to signal the completion of
- IO, polled completions do not. Hence they are require active reaping
- by the application. The benefits are more efficient IO for high IOPS
- scenarios, and lower latencies for low queue depth IO.
+ Set the percentage of I/O that will be issued with higher priority by setting
+ the priority bit. Non-read I/O is likely unaffected by ``cmdprio_percentage``.
+ This option cannot be used with the `prio` or `prioclass` options. For this
+ option to set the priority bit properly, NCQ priority must be supported and
+ enabled and :option:`direct`\=1 option must be used. fio must also be run as
+ the root user.
.. option:: fixedbufs : [io_uring]
- If fio is asked to do direct IO, then Linux will map pages for each
- IO call, and release them when IO is done. If this option is set, the
- pages are pre-mapped before IO is started. This eliminates the need to
- map and release for each IO. This is more efficient, and reduces the
- IO latency as well.
+ If fio is asked to do direct IO, then Linux will map pages for each
+ IO call, and release them when IO is done. If this option is set, the
+ pages are pre-mapped before IO is started. This eliminates the need to
+ map and release for each IO. This is more efficient, and reduces the
+ IO latency as well.
+
+.. option:: hipri : [io_uring]
+
+ If this option is set, fio will attempt to use polled IO completions.
+ Normal IO completions generate interrupts to signal the completion of
+ IO, polled completions do not. Hence they are require active reaping
+ by the application. The benefits are more efficient IO for high IOPS
+ scenarios, and lower latencies for low queue depth IO.
.. option:: registerfiles : [io_uring]
When hipri is set this determines the probability of a pvsync2 I/O being high
priority. The default is 100%.
+.. option:: nowait : [pvsync2] [libaio] [io_uring]
+
+ By default if a request cannot be executed immediately (e.g. resource starvation,
+ waiting on locks) it is queued and the initiating process will be blocked until
+ the required resource becomes free.
+
+ This option sets the RWF_NOWAIT flag (supported from the 4.14 Linux kernel) and
+ the call will return instantly with EAGAIN or a partial result rather than waiting.
+
+ It is useful to also use ignore_error=EAGAIN when using this option.
+
+ Note: glibc 2.27, 2.28 have a bug in syscall wrappers preadv2, pwritev2.
+ They return EOPNOTSUP instead of EAGAIN.
+
+ For cached I/O, using this option usually means a request operates only with
+ cached data. Currently the RWF_NOWAIT flag does not supported for cached write.
+
+ For direct I/O, requests will only succeed if cache invalidation isn't required,
+ file blocks are fully allocated and the disk request could be issued immediately.
+
.. option:: cpuload=int : [cpuio]
Attempt to use the specified percentage of CPU cycles. This is a mandatory
multiple paths exist between the client and the server or in certain loopback
configurations.
+.. option:: stat_type=str : [filestat]
+
+ Specify stat system call type to measure lookup/getattr performance.
+ Default is **stat** for :manpage:`stat(2)`.
+
.. option:: readfua=bool : [sg]
With readfua option set to 1, read operations include
defaults to 100.0, meaning that all I/Os must be equal or below to the value
set by :option:`latency_target`.
+.. option:: latency_run=bool
+
+ Used with :option:`latency_target`. If false (default), fio will find
+ the highest queue depth that meets :option:`latency_target` and exit. If
+ true, fio will continue running and try to meet :option:`latency_target`
+ by adjusting queue depth.
+
.. option:: max_latency=time
If set, fio will exit the job with an ETIMEDOUT error if it exceeds this
Set the I/O priority value of this job. Linux limits us to a positive value
between 0 and 7, with 0 being the highest. See man
:manpage:`ionice(1)`. Refer to an appropriate manpage for other operating
- systems since meaning of priority may differ.
+ systems since meaning of priority may differ. For per-command priority
+ setting, see I/O engine specific `cmdprio_percentage` and `hipri_percentage`
+ options.
.. option:: prioclass=int
- Set the I/O priority class. See man :manpage:`ionice(1)`.
+ Set the I/O priority class. See man :manpage:`ionice(1)`. For per-command
+ priority setting, see I/O engine specific `cmdprio_percentage` and
+ `hipri_percentage` options.
.. option:: cpus_allowed=str
Disable measurements of throughput/bandwidth numbers. See
:option:`disable_lat`.
+.. option:: slat_percentiles=bool
+
+ Report submission latency percentiles. Submission latency is not recorded
+ for synchronous ioengines.
+
.. option:: clat_percentiles=bool
- Enable the reporting of percentiles of completion latencies. This
- option is mutually exclusive with :option:`lat_percentiles`.
+ Report completion latency percentiles.
.. option:: lat_percentiles=bool
- Enable the reporting of percentiles of I/O latencies. This is similar
- to :option:`clat_percentiles`, except that this includes the
- submission latency. This option is mutually exclusive with
- :option:`clat_percentiles`.
+ Report total latency percentiles. Total latency is the sum of submission
+ latency and completion latency.
.. option:: percentile_list=float_list
- Overwrite the default list of percentiles for completion latencies and
- the block error histogram. Each number is a floating number in the
- range (0,100], and the maximum length of the list is 20. Use ``:`` to
- separate the numbers, and list the numbers in ascending order. For
+ Overwrite the default list of percentiles for latencies and the block error
+ histogram. Each number is a floating point number in the range (0,100], and
+ the maximum length of the list is 20. Use ``:`` to separate the numbers. For
example, ``--percentile_list=99.5:99.9`` will cause fio to report the
- values of completion latency below which 99.5% and 99.9% of the observed
- latencies fell, respectively.
+ latency durations below which 99.5% and 99.9% of the observed latencies fell,
+ respectively.
.. option:: significant_figures=int
$ fio --read_iolog="<file1>:<file2>" --merge_blktrace_file="<output_file>"
Creating only the merged file can be done by passing the command line argument
-:option:`merge-blktrace-only`.
+:option:`--merge-blktrace-only`.
Scaling traces can be done to see the relative impact of any particular trace
being slowed down or sped up. :option:`merge_blktrace_scalars` takes in a colon
and IOPS. The logs share a common format, which looks like this:
*time* (`msec`), *value*, *data direction*, *block size* (`bytes`),
- *offset* (`bytes`)
+ *offset* (`bytes`), *command priority*
*Time* for the log entry is always in milliseconds. The *value* logged depends
on the type of log, it will be one of the following:
from the start of the file for that particular I/O. The logging of the offset can be
toggled with :option:`log_offset`.
+*Command priority* is 0 for normal priority and 1 for high priority. This is controlled
+by the ioengine specific :option:`cmdprio_percentage`.
+
Fio defaults to logging every individual I/O but when windowed logging is set
through :option:`log_avg_msec`, either the average (by default) or the maximum
(:option:`log_max_value` is set) *value* seen over the specified period of time
projects / fio.git / blobdiff