same size.
.TP
.BI blocksize \fR=\fPint[,int] "\fR,\fB bs" \fR=\fPint[,int]
-Block size for I/O units. Default: 4k. Values for reads and writes can be
-specified separately in the format \fIread\fR,\fIwrite\fR, either of
-which may be empty to leave that value at its default.
+Block size for I/O units. Default: 4k. Values for reads, writes, and trims
+can be specified separately in the format \fIread\fR,\fIwrite\fR,\fItrim\fR
+either of which may be empty to leave that value at its default. If a trailing
+comma isn't given, the remainder will inherit the last value set.
.TP
.BI blocksize_range \fR=\fPirange[,irange] "\fR,\fB bsrange" \fR=\fPirange[,irange]
Specify a range of I/O block sizes. The issued I/O unit will always be a
For a random workload, set how big a percentage should be random. This defaults
to 100%, in which case the workload is fully random. It can be set from
anywhere from 0 to 100. Setting it to 0 would make the workload fully
-sequential.
-.TP
-.BI percentage_sequential \fR=\fPint
-See \fBpercentage_random\fR.
+sequential. It is possible to set different values for reads, writes, and
+trim. To do so, simply use a comma separated list. See \fBblocksize\fR.
.TP
.B norandommap
Normally \fBfio\fR will cover every block of the file when doing random I/O. If
.TP
.BI exec_prerun \fR=\fPstr
Before running the job, execute the specified command with \fBsystem\fR\|(3).
+.RS
+Output is redirected in a file called \fBjobname.prerun.txt\fR
+.RE
.TP
.BI exec_postrun \fR=\fPstr
Same as \fBexec_prerun\fR, but the command is executed after the job completes.
+.RS
+Output is redirected in a file called \fBjobname.postrun.txt\fR
+.RE
.TP
.BI ioscheduler \fR=\fPstr
Attempt to switch the device hosting the file to the specified I/O scheduler.
.BI (net,netsplice)hostname \fR=\fPstr
The host name or IP address to use for TCP or UDP based IO.
If the job is a TCP listener or UDP reader, the hostname is not
-used and must be omitted.
+used and must be omitted unless it is a valid UDP multicast address.
.TP
.BI (net,netsplice)port \fR=\fPint
The TCP or UDP port to bind to or connect to.
.TP
+.BI (net,netsplice)interface \fR=\fPstr
+The IP address of the network interface used to send or receive UDP multicast
+packets.
+.TP
+.BI (net,netsplice)ttl \fR=\fPint
+Time-to-live value for outgoing UDP multicast packets. Default: 1
+.TP
.BI (net,netsplice)nodelay \fR=\fPbool
Set TCP_NODELAY on TCP connections.
.TP
hostname must be omitted if this option is used.
.TP
.BI (net, pingpong) \fR=\fPbool
-Normal a network writer will just continue writing data, and a network reader
+Normaly a network writer will just continue writing data, and a network reader
will just consume packages. If pingpong=1 is set, a writer will send its normal
payload to the reader, then wait for the reader to send the same payload back.
This allows fio to measure network latencies. The submission and completion
latencies then measure local time spent sending or receiving, and the
completion latency measures how long it took for the other end to receive and
-send back.
+send back. For UDP multicast traffic pingpong=1 should only be set for a single
+reader when multiple readers are listening to the same address.
.TP
.BI (e4defrag,donorname) \fR=\fPstr
File will be used as a block donor (swap extents between files)