defined by \fIioengine\fR. If no \fIioengine\fR is given, list all
available ioengines.
.TP
-.BI \-\-showcmd \fR=\fPjobfile
-Convert \fIjobfile\fR to a set of command\-line options.
+.BI \-\-showcmd
+Convert given \fIjobfile\fRs to a set of command\-line options.
.TP
.BI \-\-readonly
Turn on safety read\-only checks, preventing writes and trims. The \fB\-\-readonly\fR
.PD
.RE
.P
+For Zone Block Device Mode:
+.RS
+.P
+.PD 0
+z means Zone
+.P
+.PD
+.RE
+.P
With `kb_base=1024' (the default), the unit prefixes are opposite
from those specified in the SI and IEC 80000-13 standards to provide
compatibility with old scripts. For example, 4k means 4096.
.PD
.RE
.P
+`z' suffix specifies that the value is measured in zones.
+Value is recalculated once block device's zone size becomes known.
+.P
If the option accepts an upper and lower range, use a colon ':' or
minus '\-' to separate such values. See \fIirange\fR parameter type.
If the lower value specified happens to be larger than the upper value
specified, but lets all clones use the same file if set).
.RS
.P
-See the \fBfilename\fR option for information on how to escape ':' and '\\'
+See the \fBfilename\fR option for information on how to escape ':'
characters within the directory path itself.
.P
Note: To control the directory fio will use for internal state files
explicit size is specified by \fBfilesize\fR.
.RS
.P
-Each colon and backslash in the wanted path must be escaped with a '\\'
+Each colon in the wanted path must be escaped with a '\e'
character. For instance, if the path is `/dev/dsk/foo@3,0:c' then you
would use `filename=/dev/dsk/foo@3,0\\:c' and if the path is
-`F:\\filename' then you would use `filename=F\\:\\\\filename'.
+`F:\\filename' then you would use `filename=F\\:\\filename'.
.P
On Windows, disk devices are accessed as `\\\\.\\PhysicalDrive0' for
the first device, `\\\\.\\PhysicalDrive1' for the second etc.
.B $jobname
The name of the worker thread or process.
.TP
+.B $clientuid
+IP of the fio process when using client/server mode.
+.TP
.B $jobnum
The incremental number of the worker thread or process.
.TP
.TP
.BI ioscheduler \fR=\fPstr
Attempt to switch the device hosting the file to the specified I/O scheduler
-before running.
+before running. If the file is a pipe, a character device file or if device
+hosting the file could not be determined, this option is ignored.
.TP
.BI create_serialize \fR=\fPbool
If true, serialize the file creation for the jobs. This may be handy to
.RS
.TP
.B none
-The \fBzonerange\fR, \fBzonesize\fR and \fBzoneskip\fR parameters are ignored.
+The \fBzonerange\fR, \fBzonesize\fR \fBzonecapacity\fR and \fBzoneskip\fR
+parameters are ignored.
.TP
.B strided
I/O happens in a single zone until \fBzonesize\fR bytes have been transferred.
After that number of bytes has been transferred processing of the next zone
-starts.
+starts. The \fBzonecapacity\fR parameter is ignored.
.TP
.B zbd
Zoned block device mode. I/O happens sequentially in each zone, even if random
I/O has been selected. Random I/O happens across all zones instead of being
restricted to a single zone.
+Trim is handled using a zone reset operation. Trim only considers non-empty
+sequential write required and sequential write preferred zones.
.RE
.RE
.TP
device zone size. For a regular block device or file, the specified
\fBzonesize\fR must be at least 512B.
.TP
-.BI zoneskip \fR=\fPint
+.BI zonecapacity \fR=\fPint
+For \fBzonemode\fR=zbd, this defines the capacity of a single zone, which is
+the accessible area starting from the zone start address. This parameter only
+applies when using \fBzonemode\fR=zbd in combination with regular block devices.
+If not specified it defaults to the zone size. If the target device is a zoned
+block device, the zone capacity is obtained from the device information and this
+option is ignored.
+.TP
+.BI zoneskip \fR=\fPint[z]
For \fBzonemode\fR=strided, the number of bytes to skip after \fBzonesize\fR
bytes of data have been transferred.
so. Default: false.
.TP
.BI max_open_zones \fR=\fPint
-When running a random write test across an entire drive many more zones will be
-open than in a typical application workload. Hence this command line option
-that allows to limit the number of open zones. The number of open zones is
-defined as the number of zones to which write commands are issued.
+A zone of a zoned block device is in the open state when it is partially written
+(i.e. not all sectors of the zone have been written). Zoned block devices may
+have limit a on the total number of zones that can be simultaneously in the
+open state, that is, the number of zones that can be written to simultaneously.
+The \fBmax_open_zones\fR parameter limits the number of zones to which write
+commands are issued by all fio jobs, that is, limits the number of zones that
+will be in the open state. This parameter is relevant only if the
+\fBzonemode=zbd\fR is used. The default value is always equal to maximum number
+of open zones of the target zoned block device and a value higher than this
+limit cannot be specified by users unless the option \fBignore_zone_limits\fR is
+specified. When \fBignore_zone_limits\fR is specified or the target device has
+no limit on the number of zones that can be in an open state,
+\fBmax_open_zones\fR can specify 0 to disable any limit on the number of zones
+that can be simultaneously written to by all jobs.
+.TP
+.BI job_max_open_zones \fR=\fPint
+In the same manner as \fBmax_open_zones\fR, limit the number of open zones per
+fio job, that is, the number of zones that a single job can simultaneously write
+to. A value of zero indicates no limit. Default: zero.
+.TP
+.BI ignore_zone_limits \fR=\fPbool
+If this option is used, fio will ignore the maximum number of open zones limit
+of the zoned block device in use, thus allowing the option \fBmax_open_zones\fR
+value to be larger than the device reported limit. Default: false.
.TP
.BI zone_reset_threshold \fR=\fPfloat
-A number between zero and one that indicates the ratio of logical blocks with
-data to the total number of logical blocks in the test above which zones
-should be reset periodically.
+A number between zero and one that indicates the ratio of written bytes in the
+zones with write pointers in the IO range to the size of the IO range. When
+current ratio is above this ratio, zones are reset periodically as
+\fBzone_reset_frequency\fR specifies. If there are multiple jobs when using this
+option, the IO range for all write jobs has to be the same.
.TP
.BI zone_reset_frequency \fR=\fPfloat
A number between zero and one that indicates how often a zone reset should be
OpenBSD and ZFS on Solaris don't support direct I/O. On Windows the synchronous
ioengines don't support direct I/O. Default: false.
.TP
-.BI atomic \fR=\fPbool
-If value is true, attempt to use atomic direct I/O. Atomic writes are
-guaranteed to be stable once acknowledged by the operating system. Only
-Linux supports O_ATOMIC right now.
-.TP
.BI buffered \fR=\fPbool
If value is true, use buffered I/O. This is the opposite of the
\fBdirect\fR option. Defaults to true.
.TP
.B trimwrite
Sequential trim+write sequences. Blocks will be trimmed first,
-then the same blocks will be written to.
+then the same blocks will be written to. So if `io_size=64K' is specified,
+Fio will trim a total of 64K bytes and also write 64K bytes on the same
+trimmed blocks. This behaviour will be consistent with `number_ios' or
+other Fio options limiting the total bytes or number of I/O's.
+.TP
+.B randtrimwrite
+Like
+.B trimwrite ,
+but uses random offsets rather than sequential writes.
.RE
.P
Fio defaults to read if the option is not specified. For the mixed I/O
.P
\fBsequential\fR is only useful for random I/O, where fio would normally
generate a new random offset for every I/O. If you append e.g. 8 to randread,
-you would get a new random offset for every 8 I/Os. The result would be a
-seek for only every 8 I/Os, instead of for every I/O. Use `rw=randread:8'
-to specify that. As sequential I/O is already sequential, setting
-\fBsequential\fR for that would not result in any differences. \fBidentical\fR
-behaves in a similar fashion, except it sends the same offset 8 number of
-times before generating a new offset.
+i.e. `rw=randread:8' you would get a new random offset for every 8 I/Os. The
+result would be a sequence of 8 sequential offsets with a random starting
+point. However this behavior may change if a sequential I/O reaches end of the
+file. As sequential I/O is already sequential, setting \fBsequential\fR for
+that would not result in any difference. \fBidentical\fR behaves in a similar
+fashion, except it sends the same offset 8 number of times before generating a
+new offset.
+.P
+.P
+Example #1:
+.RS
+.P
+.PD 0
+rw=randread:8
+.P
+rw_sequencer=sequential
+.P
+bs=4k
+.PD
+.RE
+.P
+The generated sequence of offsets will look like this:
+4k, 8k, 12k, 16k, 20k, 24k, 28k, 32k, 92k, 96k, 100k, 104k, 108k, 112k, 116k,
+120k, 48k, 52k ...
+.P
+.P
+Example #2:
+.RS
+.P
+.PD 0
+rw=randread:8
+.P
+rw_sequencer=identical
+.P
+bs=4k
+.PD
+.RE
+.P
+The generated sequence of offsets will look like this:
+4k, 4k, 4k, 4k, 4k, 4k, 4k, 4k, 92k, 92k, 92k, 92k, 92k, 92k, 92k, 92k, 48k,
+48k, 48k ...
.RE
.TP
-.BI unified_rw_reporting \fR=\fPbool
+.BI unified_rw_reporting \fR=\fPstr
Fio normally reports statistics on a per data direction basis, meaning that
-reads, writes, and trims are accounted and reported separately. If this
-option is set fio sums the results and report them as "mixed" instead.
+reads, writes, and trims are accounted and reported separately. This option
+determines whether fio reports the results normally, summed together, or as
+both options.
+Accepted values are:
+.RS
+.TP
+.B none
+Normal statistics reporting.
+.TP
+.B mixed
+Statistics are summed per data direction and reported together.
+.TP
+.B both
+Statistics are reported normally, followed by the mixed statistics.
+.TP
+.B 0
+Backward-compatible alias for \fBnone\fR.
+.TP
+.B 1
+Backward-compatible alias for \fBmixed\fR.
+.TP
+.B 2
+Alias for \fBboth\fR.
+.RE
.TP
.BI randrepeat \fR=\fPbool
Seed the random number generator used for random I/O patterns in a
should be associated with them.
.RE
.TP
-.BI offset \fR=\fPint
+.BI offset \fR=\fPint[%|z]
Start I/O at the provided offset in the file, given as either a fixed size in
-bytes or a percentage. If a percentage is given, the generated offset will be
+bytes, zones or a percentage. If a percentage is given, the generated offset will be
aligned to the minimum \fBblocksize\fR or to the value of \fBoffset_align\fR if
provided. Data before the given offset will not be touched. This
effectively caps the file size at `real_size \- offset'. Can be combined with
\fBsize\fR to constrain the start and end range of the I/O workload.
A percentage can be specified by a number between 1 and 100 followed by '%',
-for example, `offset=20%' to specify 20%.
+for example, `offset=20%' to specify 20%. In ZBD mode, value can be set as
+number of zones using 'z'.
.TP
.BI offset_align \fR=\fPint
If set to non-zero value, the byte offset generated by a percentage \fBoffset\fR
is aligned upwards to this value. Defaults to 0 meaning that a percentage
offset is aligned to the minimum block size.
.TP
-.BI offset_increment \fR=\fPint
+.BI offset_increment \fR=\fPint[%|z]
If this is provided, then the real offset becomes `\fBoffset\fR + \fBoffset_increment\fR
* thread_number', where the thread number is a counter that starts at 0 and
is incremented for each sub-job (i.e. when \fBnumjobs\fR option is
intended to operate on a file in parallel disjoint segments, with even
spacing between the starting points. Percentages can be used for this option.
If a percentage is given, the generated offset will be aligned to the minimum
-\fBblocksize\fR or to the value of \fBoffset_align\fR if provided.
+\fBblocksize\fR or to the value of \fBoffset_align\fR if provided.In ZBD mode, value
+can be set as number of zones using 'z'.
.TP
.BI number_ios \fR=\fPint
Fio will normally perform I/Os until it has exhausted the size of the region
.TP
.BI fdatasync \fR=\fPint
Like \fBfsync\fR but uses \fBfdatasync\fR\|(2) to only sync data and
-not metadata blocks. In Windows, FreeBSD, DragonFlyBSD or OSX there is no
+not metadata blocks. In Windows, DragonFlyBSD or OSX there is no
\fBfdatasync\fR\|(2) so this falls back to using \fBfsync\fR\|(2).
Defaults to 0, which means fio does not periodically issue and wait for a
data-only sync to complete.
limit reads or writes to a certain rate. If that is the case, then the
distribution may be skewed. Default: 50.
.TP
-.BI random_distribution \fR=\fPstr:float[,str:float][,str:float]
+.BI random_distribution \fR=\fPstr:float[:float][,str:float][,str:float]
By default, fio will use a completely uniform random distribution when asked
to perform random I/O. Sometimes it is useful to skew the distribution in
specific ways, ensuring that some parts of the data is more hot than others.
map. For the \fBnormal\fR distribution, a normal (Gaussian) deviation is
supplied as a value between 0 and 100.
.P
+The second, optional float is allowed for \fBpareto\fR, \fBzipf\fR and \fBnormal\fR
+distributions. It allows one to set base of distribution in non-default place, giving
+more control over most probable outcome. This value is in range [0-1] which maps linearly to
+range of possible random values.
+Defaults are: random for \fBpareto\fR and \fBzipf\fR, and 0.5 for \fBnormal\fR.
+If you wanted to use \fBzipf\fR with a `theta` of 1.2 centered on 1/4 of allowed value range,
+you would use `random_distribution=zipf:1.2:0.25`.
+.P
For a \fBzoned\fR distribution, fio supports specifying percentages of I/O
access that should fall within what range of the file or device. For
example, given a criteria of:
this option will also enable \fBrefill_buffers\fR to prevent every buffer
being identical.
.TP
+.BI dedupe_mode \fR=\fPstr
+If \fBdedupe_percentage\fR is given, then this option controls how fio
+generates the dedupe buffers.
+.RS
+.RS
+.TP
+.B repeat
+.P
+.RS
+Generate dedupe buffers by repeating previous writes
+.RE
+.TP
+.B working_set
+.P
+.RS
+Generate dedupe buffers from working set
+.RE
+.RE
+.P
+\fBrepeat\fR is the default option for fio. Dedupe buffers are generated
+by repeating previous unique write.
+
+\fBworking_set\fR is a more realistic workload.
+With \fBworking_set\fR, \fBdedupe_working_set_percentage\fR should be provided.
+Given that, fio will use the initial unique write buffers as its working set.
+Upon deciding to dedupe, fio will randomly choose a buffer from the working set.
+Note that by using \fBworking_set\fR the dedupe percentage will converge
+to the desired over time while \fBrepeat\fR maintains the desired percentage
+throughout the job.
+.RE
+.RE
+.TP
+.BI dedupe_working_set_percentage \fR=\fPint
+If \fBdedupe_mode\fR is set to \fBworking_set\fR, then this controls
+the percentage of size of the file or device used as the buffers
+fio will choose to generate the dedupe buffers from
+.P
+.RS
+Note that \fBsize\fR needs to be explicitly provided and only 1 file
+per job is supported
+.RE
+.TP
+.BI dedupe_global \fR=\fPbool
+This controls whether the deduplication buffers will be shared amongst
+all jobs that have this option set. The buffers are spread evenly between
+participating jobs.
+.P
+.RS
+Note that \fBdedupe_mode\fR must be set to \fBworking_set\fR for this to work.
+Can be used in combination with compression
+.TP
.BI invalidate \fR=\fPbool
Invalidate the buffer/page cache parts of the files to be used prior to
starting I/O if the platform and file type support it. Defaults to true.
This will be ignored if \fBpre_read\fR is also specified for the
same job.
.TP
-.BI sync \fR=\fPbool
-Use synchronous I/O for buffered writes. For the majority of I/O engines,
-this means using O_SYNC. Default: false.
+.BI sync \fR=\fPstr
+Whether, and what type, of synchronous I/O to use for writes. The allowed
+values are:
+.RS
+.RS
+.TP
+.B none
+Do not use synchronous IO, the default.
+.TP
+.B 0
+Same as \fBnone\fR.
+.TP
+.B sync
+Use synchronous file IO. For the majority of I/O engines,
+this means using O_SYNC.
+.TP
+.B 1
+Same as \fBsync\fR.
+.TP
+.B dsync
+Use synchronous data IO. For the majority of I/O engines,
+this means using O_DSYNC.
+.PD
+.RE
+.RE
.TP
.BI iomem \fR=\fPstr "\fR,\fP mem" \fR=\fPstr
Fio can use various types of memory as the I/O unit buffer. The allowed
\fBmmaphuge\fR to work, the system must have free huge pages allocated. This
can normally be checked and set by reading/writing
`/proc/sys/vm/nr_hugepages' on a Linux system. Fio assumes a huge page
-is 4MiB in size. So to calculate the number of huge pages you need for a
-given job file, add up the I/O depth of all jobs (normally one unless
-\fBiodepth\fR is used) and multiply by the maximum bs set. Then divide
-that number by the huge page size. You can see the size of the huge pages in
-`/proc/meminfo'. If no huge pages are allocated by having a non-zero
+is 2 or 4MiB in size depending on the platform. So to calculate the number of
+huge pages you need for a given job file, add up the I/O depth of all jobs
+(normally one unless \fBiodepth\fR is used) and multiply by the maximum bs set.
+Then divide that number by the huge page size. You can see the size of the huge
+pages in `/proc/meminfo'. If no huge pages are allocated by having a non-zero
number in `nr_hugepages', using \fBmmaphuge\fR or \fBshmhuge\fR will fail. Also
see \fBhugepage\-size\fR.
.P
\fBbs\fR used.
.TP
.BI hugepage\-size \fR=\fPint
-Defines the size of a huge page. Must at least be equal to the system
-setting, see `/proc/meminfo'. Defaults to 4MiB. Should probably
-always be a multiple of megabytes, so using `hugepage\-size=Xm' is the
-preferred way to set this to avoid setting a non-pow-2 bad value.
+Defines the size of a huge page. Must at least be equal to the system setting,
+see `/proc/meminfo' and `/sys/kernel/mm/hugepages/'. Defaults to 2 or 4MiB
+depending on the platform. Should probably always be a multiple of megabytes,
+so using `hugepage\-size=Xm' is the preferred way to set this to avoid setting
+a non-pow-2 bad value.
.TP
.BI lockmem \fR=\fPint
Pin the specified amount of memory with \fBmlock\fR\|(2). Can be used to
simulate a smaller amount of memory. The amount specified is per worker.
.SS "I/O size"
.TP
-.BI size \fR=\fPint
+.BI size \fR=\fPint[%|z]
The total size of file I/O for each thread of this job. Fio will run until
-this many bytes has been transferred, unless runtime is limited by other options
-(such as \fBruntime\fR, for instance, or increased/decreased by \fBio_size\fR).
+this many bytes has been transferred, unless runtime is altered by other means
+such as (1) \fBruntime\fR, (2) \fBio_size\fR, (3) \fBnumber_ios\fR, (4)
+gaps/holes while doing I/O's such as `rw=read:16K', or (5) sequential I/O
+reaching end of the file which is possible when \fBpercentage_random\fR is
+less than 100.
Fio will divide this size between the available files determined by options
such as \fBnrfiles\fR, \fBfilename\fR, unless \fBfilesize\fR is
specified by the job. If the result of division happens to be 0, the size is
If this option is not specified, fio will use the full size of the given
files or devices. If the files do not exist, size must be given. It is also
possible to give size as a percentage between 1 and 100. If `size=20%' is
-given, fio will use 20% of the full size of the given files or devices.
-Can be combined with \fBoffset\fR to constrain the start and end range
-that I/O will be done within.
+given, fio will use 20% of the full size of the given files or devices. In ZBD mode,
+size can be given in units of number of zones using 'z'. Can be combined with \fBoffset\fR to
+constrain the start and end range that I/O will be done within.
.TP
-.BI io_size \fR=\fPint "\fR,\fB io_limit" \fR=\fPint
+.BI io_size \fR=\fPint[%|z] "\fR,\fB io_limit" \fR=\fPint[%|z]
Normally fio operates within the region set by \fBsize\fR, which means
that the \fBsize\fR option sets both the region and size of I/O to be
performed. Sometimes that is not what you want. With this option, it is
will perform I/O within the first 20GiB but exit when 5GiB have been
done. The opposite is also possible \-\- if \fBsize\fR is set to 20GiB,
and \fBio_size\fR is set to 40GiB, then fio will do 40GiB of I/O within
-the 0..20GiB region.
+the 0..20GiB region. Value can be set as percentage: \fBio_size\fR=N%.
+In this case \fBio_size\fR multiplies \fBsize\fR= value. In ZBD mode, value can
+also be set as number of zones using 'z'.
.TP
.BI filesize \fR=\fPirange(int)
Individual file sizes. May be a range, in which case fio will select sizes
-for files at random within the given range and limited to \fBsize\fR in
-total (if that is given). If not given, each created file is the same size.
-This option overrides \fBsize\fR in terms of file size, which means
-this value is used as a fixed size or possible range of each file.
+for files at random within the given range. If not given, each created file
+is the same size. This option overrides \fBsize\fR in terms of file size,
+i.e. \fBsize\fR becomes merely the default for \fBio_size\fR (and
+has no effect it all if \fBio_size\fR is set explicitly).
.TP
.BI file_append \fR=\fPbool
Perform I/O after the end of the file. Normally fio will operate within the
.TP
.BI fill_device \fR=\fPbool "\fR,\fB fill_fs" \fR=\fPbool
Sets size to something really large and waits for ENOSPC (no space left on
-device) as the terminating condition. Only makes sense with sequential
+device) or EDQUOT (disk quota exceeded)
+as the terminating condition. Only makes sense with sequential
write. For a read workload, the mount point will be filled first then I/O
-started on the result. This option doesn't make sense if operating on a raw
-device node, since the size of that is already known by the file system.
-Additionally, writing beyond end-of-device will not return ENOSPC there.
+started on the result.
.SS "I/O engine"
.TP
.BI ioengine \fR=\fPstr
.B pvsync2
Basic \fBpreadv2\fR\|(2) or \fBpwritev2\fR\|(2) I/O.
.TP
+.B io_uring
+Fast Linux native asynchronous I/O. Supports async IO
+for both direct and buffered IO.
+This engine defines engine specific options.
+.TP
+.B io_uring_cmd
+Fast Linux native asynchronous I/O for passthrough commands.
+This engine defines engine specific options.
+.TP
.B libaio
Linux native asynchronous I/O. Note that Linux may only support
queued behavior with non-buffered I/O (set `direct=1' or
character devices. This engine supports trim operations. The
sg engine includes engine specific options.
.TP
+.B libzbc
+Read, write, trim and ZBC/ZAC operations to a zoned block device using
+\fBlibzbc\fR library. The target can be either an SG character device or
+a block device file.
+.TP
.B null
Doesn't transfer any data, just pretends to. This is mainly used to
exercise fio itself and for debugging/testing purposes.
.TP
.B cpuio
Doesn't transfer any data, but burns CPU cycles according to the
-\fBcpuload\fR and \fBcpuchunks\fR options. Setting
-\fBcpuload\fR\=85 will cause that job to do nothing but burn 85%
-of the CPU. In case of SMP machines, use `numjobs=<nr_of_cpu>'
-to get desired CPU usage, as the cpuload only loads a
-single CPU at the desired rate. A job never finishes unless there is
-at least one non-cpuio job.
-.TP
-.B guasi
-The GUASI I/O engine is the Generic Userspace Asynchronous Syscall
-Interface approach to async I/O. See \fIhttp://www.xmailserver.org/guasi-lib.html\fR
-for more info on GUASI.
+\fBcpuload\fR, \fBcpuchunks\fR and \fBcpumode\fR options.
+A job never finishes unless there is at least one non-cpuio job.
+.RS
+.P
+.PD 0
+\fBcpuload\fR\=85 will cause that job to do nothing but burn 85% of the CPU.
+In case of SMP machines, use \fBnumjobs=<nr_of_cpu>\fR\ to get desired CPU usage,
+as the cpuload only loads a single CPU at the desired rate.
+
+.P
+\fBcpumode\fR\=qsort replace the default noop instructions loop
+by a qsort algorithm to consume more energy.
+
+.P
+.RE
.TP
.B rdma
The RDMA I/O engine supports both RDMA memory semantics
before overwriting. The \fBtrimwrite\fR mode works well for this
constraint.
.TP
-.B pmemblk
-Read and write using filesystem DAX to a file on a filesystem
-mounted with DAX on a persistent memory device through the PMDK
-libpmemblk library.
-.TP
.B dev\-dax
Read and write using device DAX to a persistent memory device (e.g.,
/dev/dax0.0) through the PMDK libpmem library.
\fBfilesize\fR so that all the accounting still occurs, but no actual I/O will be
done other than creating the file.
.TP
+.B filestat
+Simply do stat() and do no I/O to the file. You need to set 'filesize'
+and 'nrfiles', so that files will be created.
+This engine is to measure file lookup and meta data access.
+.TP
+.B filedelete
+Simply delete files by unlink() and do no I/O to the file. You need to set 'filesize'
+and 'nrfiles', so that files will be created.
+This engine is to measure file delete.
+.TP
.B libpmem
Read and write using mmap I/O to a file on a filesystem
mounted with DAX on a persistent memory device through the PMDK
.TP
.B nbd
Synchronous read and write a Network Block Device (NBD).
+.TP
+.B libcufile
+I/O engine supporting libcufile synchronous access to nvidia-fs and a
+GPUDirect Storage-supported filesystem. This engine performs
+I/O without transferring buffers between user-space and the kernel,
+unless \fBverify\fR is set or \fBcuda_io\fR is \fBposix\fR. \fBiomem\fR must
+not be \fBcudamalloc\fR. This ioengine defines engine specific options.
+.TP
+.B dfs
+I/O engine supporting asynchronous read and write operations to the DAOS File
+System (DFS) via libdfs.
+.TP
+.B nfs
+I/O engine supporting asynchronous read and write operations to
+NFS filesystems from userspace via libnfs. This is useful for
+achieving higher concurrency and thus throughput than is possible
+via kernel NFS.
+.TP
+.B exec
+Execute 3rd party tools. Could be used to perform monitoring during jobs runtime.
+.TP
+.B xnvme
+I/O engine using the xNVMe C API, for NVMe devices. The xnvme engine provides
+flexibility to access GNU/Linux Kernel NVMe driver via libaio, IOCTLs, io_uring,
+the SPDK NVMe driver, or your own custom NVMe driver. The xnvme engine includes
+engine specific options. (See \fIhttps://xnvme.io/\fR).
+.TP
+.B libblkio
+Use the libblkio library (\fIhttps://gitlab.com/libblkio/libblkio\fR). The
+specific driver to use must be set using \fBlibblkio_driver\fR. If
+\fBmem\fR/\fBiomem\fR is not specified, memory allocation is delegated to
+libblkio (and so is guaranteed to work with the selected driver). One libblkio
+instance is used per process, so all jobs setting option \fBthread\fR will share
+a single instance (with one queue per thread) and must specify compatible
+options. Note that some drivers don't allow several instances to access the same
+device or file simultaneously, but allow it for threads.
.SS "I/O engine specific parameters"
In addition, there are some parameters which are only valid when a specific
\fBioengine\fR is in use. These are used identically to normal parameters,
with the caveat that when used on the command line, they must come after the
\fBioengine\fR that defines them is selected.
.TP
-.BI (io_uring)hipri
-If this option is set, fio will attempt to use polled IO completions. Normal IO
-completions generate interrupts to signal the completion of IO, polled
-completions do not. Hence they are require active reaping by the application.
-The benefits are more efficient IO for high IOPS scenarios, and lower latencies
-for low queue depth IO.
+.BI (io_uring,libaio)cmdprio_percentage \fR=\fPint[,int]
+Set the percentage of I/O that will be issued with the highest priority.
+Default: 0. A single value applies to reads and writes. Comma-separated
+values may be specified for reads and writes. For this option to be effective,
+NCQ priority must be supported and enabled, and `direct=1' option must be
+used. fio must also be run as the root user. Unlike slat/clat/lat stats, which
+can be tracked and reported independently, per priority stats only track and
+report a single type of latency. By default, completion latency (clat) will be
+reported, if \fBlat_percentiles\fR is set, total latency (lat) will be reported.
+.TP
+.BI (io_uring,libaio)cmdprio_class \fR=\fPint[,int]
+Set the I/O priority class to use for I/Os that must be issued with a
+priority when \fBcmdprio_percentage\fR or \fBcmdprio_bssplit\fR is set.
+If not specified when \fBcmdprio_percentage\fR or \fBcmdprio_bssplit\fR
+is set, this defaults to the highest priority class. A single value applies
+to reads and writes. Comma-separated values may be specified for reads and
+writes. See man \fBionice\fR\|(1). See also the \fBprioclass\fR option.
+.TP
+.BI (io_uring,libaio)cmdprio \fR=\fPint[,int]
+Set the I/O priority value to use for I/Os that must be issued with a
+priority when \fBcmdprio_percentage\fR or \fBcmdprio_bssplit\fR is set.
+If not specified when \fBcmdprio_percentage\fR or \fBcmdprio_bssplit\fR
+is set, this defaults to 0. Linux limits us to a positive value between
+0 and 7, with 0 being the highest. A single value applies to reads and writes.
+Comma-separated values may be specified for reads and writes. See man
+\fBionice\fR\|(1). Refer to an appropriate manpage for other operating systems
+since the meaning of priority may differ. See also the \fBprio\fR option.
.TP
-.BI (io_uring)fixedbufs
+.BI (io_uring,libaio)cmdprio_bssplit \fR=\fPstr[,str]
+To get a finer control over I/O priority, this option allows specifying
+the percentage of IOs that must have a priority set depending on the block
+size of the IO. This option is useful only when used together with the option
+\fBbssplit\fR, that is, multiple different block sizes are used for reads and
+writes.
+.RS
+.P
+The first accepted format for this option is the same as the format of the
+\fBbssplit\fR option:
+.RS
+.P
+cmdprio_bssplit=blocksize/percentage:blocksize/percentage
+.RE
+.P
+In this case, each entry will use the priority class and priority level defined
+by the options \fBcmdprio_class\fR and \fBcmdprio\fR respectively.
+.P
+The second accepted format for this option is:
+.RS
+.P
+cmdprio_bssplit=blocksize/percentage/class/level:blocksize/percentage/class/level
+.RE
+.P
+In this case, the priority class and priority level is defined inside each
+entry. In comparison with the first accepted format, the second accepted format
+does not restrict all entries to have the same priority class and priority
+level.
+.P
+For both formats, only the read and write data directions are supported, values
+for trim IOs are ignored. This option is mutually exclusive with the
+\fBcmdprio_percentage\fR option.
+.RE
+.TP
+.BI (io_uring,io_uring_cmd)fixedbufs
If fio is asked to do direct IO, then Linux will map pages for each IO call, and
release them when IO is done. If this option is set, the pages are pre-mapped
before IO is started. This eliminates the need to map and release for each IO.
This is more efficient, and reduces the IO latency as well.
.TP
-.BI (io_uring)registerfiles
+.BI (io_uring,io_uring_cmd)nonvectored \fR=\fPint
+With this option, fio will use non-vectored read/write commands, where address
+must contain the address directly. Default is -1.
+.TP
+.BI (io_uring,io_uring_cmd)force_async
+Normal operation for io_uring is to try and issue an sqe as non-blocking first,
+and if that fails, execute it in an async manner. With this option set to N,
+then every N request fio will ask sqe to be issued in an async manner. Default
+is 0.
+.TP
+.BI (io_uring,io_uring_cmd,xnvme)hipri
+If this option is set, fio will attempt to use polled IO completions. Normal IO
+completions generate interrupts to signal the completion of IO, polled
+completions do not. Hence they are require active reaping by the application.
+The benefits are more efficient IO for high IOPS scenarios, and lower latencies
+for low queue depth IO.
+.TP
+.BI (io_uring,io_uring_cmd)registerfiles
With this option, fio registers the set of files being used with the kernel.
This avoids the overhead of managing file counts in the kernel, making the
submission and completion part more lightweight. Required for the below
sqthread_poll option.
.TP
-.BI (io_uring)sqthread_poll
+.BI (io_uring,io_uring_cmd,xnvme)sqthread_poll
Normally fio will submit IO by issuing a system call to notify the kernel of
available items in the SQ ring. If this option is set, the act of submitting IO
will be done by a polling thread in the kernel. This frees up cycles for fio, at
-the cost of using more CPU in the system.
+the cost of using more CPU in the system. As submission is just the time it
+takes to fill in the sqe entries and any syscall required to wake up the idle
+kernel thread, fio will not report submission latencies.
.TP
-.BI (io_uring)sqthread_poll_cpu
+.BI (io_uring,io_uring_cmd)sqthread_poll_cpu \fR=\fPint
When `sqthread_poll` is set, this option provides a way to define which CPU
should be used for the polling thread.
.TP
+.BI (io_uring_cmd)cmd_type \fR=\fPstr
+Specifies the type of uring passthrough command to be used. Supported
+value is nvme. Default is nvme.
+.TP
.BI (libaio)userspace_reap
Normally, with the libaio engine in use, fio will use the
\fBio_getevents\fR\|(3) system call to reap newly returned events. With
When hipri is set this determines the probability of a pvsync2 I/O being high
priority. The default is 100%.
.TP
+.BI (pvsync2,libaio,io_uring,io_uring_cmd)nowait \fR=\fPbool
+By default if a request cannot be executed immediately (e.g. resource starvation,
+waiting on locks) it is queued and the initiating process will be blocked until
+the required resource becomes free.
+This option sets the RWF_NOWAIT flag (supported from the 4.14 Linux kernel) and
+the call will return instantly with EAGAIN or a partial result rather than waiting.
+
+It is useful to also use \fBignore_error\fR=EAGAIN when using this option.
+Note: glibc 2.27, 2.28 have a bug in syscall wrappers preadv2, pwritev2.
+They return EOPNOTSUP instead of EAGAIN.
+
+For cached I/O, using this option usually means a request operates only with
+cached data. Currently the RWF_NOWAIT flag does not supported for cached write.
+For direct I/O, requests will only succeed if cache invalidation isn't required,
+file blocks are fully allocated and the disk request could be issued immediately.
+.TP
.BI (cpuio)cpuload \fR=\fPint
Attempt to use the specified percentage of CPU cycles. This is a mandatory
option when using cpuio I/O engine.
.BI (cpuio)cpuchunks \fR=\fPint
Split the load into cycles of the given time. In microseconds.
.TP
+.BI (cpuio)cpumode \fR=\fPstr
+Specify how to stress the CPU. It can take these two values:
+.RS
+.RS
+.TP
+.B noop
+This is the default and directs the CPU to execute noop instructions.
+.TP
+.B qsort
+Replace the default noop instructions with a qsort algorithm to consume more energy.
+.RE
+.RE
+.TP
.BI (cpuio)exit_on_io_done \fR=\fPbool
Detect when I/O threads are done, then exit.
.TP
.BI (libhdfs)namenode \fR=\fPstr
The hostname or IP address of a HDFS cluster namenode to contact.
.TP
-.BI (libhdfs)port
+.BI (libhdfs)port \fR=\fPint
The listening port of the HFDS cluster namenode.
.TP
-.BI (netsplice,net)port
+.BI (netsplice,net)port \fR=\fPint
The TCP or UDP port to bind to or connect to. If this is used with
\fBnumjobs\fR to spawn multiple instances of the same job type, then
this will be the starting port number since fio will use a range of
ports.
.TP
-.BI (rdma)port
+.BI (rdma,librpma_*)port \fR=\fPint
The port to use for RDMA-CM communication. This should be the same
value on the client and the server side.
.TP
-.BI (netsplice,net, rdma)hostname \fR=\fPstr
+.BI (netsplice,net,rdma)hostname \fR=\fPstr
The hostname or IP address to use for TCP, UDP or RDMA-CM based I/O.
If the job is a TCP listener or UDP reader, the hostname is not used
and must be omitted unless it is a valid UDP multicast address.
.TP
+.BI (librpma_*)serverip \fR=\fPstr
+The IP address to be used for RDMA-CM based I/O.
+.TP
+.BI (librpma_*_server)direct_write_to_pmem \fR=\fPbool
+Set to 1 only when Direct Write to PMem from the remote host is possible. Otherwise, set to 0.
+.TP
+.BI (librpma_*_server)busy_wait_polling \fR=\fPbool
+Set to 0 to wait for completion instead of busy-wait polling completion.
+Default: 1.
+.TP
.BI (netsplice,net)interface \fR=\fPstr
The IP address of the network interface used to send or receive UDP
multicast.
the full *type.id* string. If no type. prefix is given, fio will add 'client.'
by default.
.TP
+.BI (rados)conf \fR=\fPstr
+Specifies the configuration path of ceph cluster, so conf file does not
+have to be /etc/ceph/ceph.conf.
+.TP
.BI (rbd,rados)busy_poll \fR=\fPbool
Poll store instead of waiting for completion. Usually this provides better
throughput at cost of higher(up to 100%) CPU utilization.
.TP
+.BI (rados)touch_objects \fR=\fPbool
+During initialization, touch (create if do not exist) all objects (files).
+Touching all objects affects ceph caches and likely impacts test results.
+Enabled by default.
+.TP
.BI (http)http_host \fR=\fPstr
Hostname to connect to. For S3, this could be the bucket name. Default
is \fBlocalhost\fR
.BI (http)http_s3_keyid \fR=\fPstr
The S3 key/access id.
.TP
+.BI (http)http_s3_sse_customer_key \fR=\fPstr
+The encryption customer key in SSE server side.
+.TP
+.BI (http)http_s3_sse_customer_algorithm \fR=\fPstr
+The encryption customer algorithm in SSE server side. Default is \fBAES256\fR
+.TP
+.BI (http)http_s3_storage_class \fR=\fPstr
+Which storage class to access. User-customizable settings. Default is \fBSTANDARD\fR
+.TP
.BI (http)http_swift_auth_token \fR=\fPstr
The Swift auth token. See the example configuration file on how to
retrieve this.
function. This can be useful when multiple paths exist between the
client and the server or in certain loopback configurations.
.TP
+.BI (filestat)stat_type \fR=\fPstr
+Specify stat system call type to measure lookup/getattr performance.
+Default is \fBstat\fR for \fBstat\fR\|(2).
+.TP
+.BI (sg)hipri
+If this option is set, fio will attempt to use polled IO completions. This
+will have a similar effect as (io_uring)hipri. Only SCSI READ and WRITE
+commands will have the SGV4_FLAG_HIPRI set (not UNMAP (trim) nor VERIFY).
+Older versions of the Linux sg driver that do not support hipri will simply
+ignore this flag and do normal IO. The Linux SCSI Low Level Driver (LLD)
+that "owns" the device also needs to support hipri (also known as iopoll
+and mq_poll). The MegaRAID driver is an example of a SCSI LLD.
+Default: clear (0) which does normal (interrupted based) IO.
+.TP
.BI (sg)readfua \fR=\fPbool
With readfua option set to 1, read operations include the force
unit access (fua) flag. Default: 0.
unit access (fua) flag. Default: 0.
.TP
.BI (sg)sg_write_mode \fR=\fPstr
-Specify the type of write commands to issue. This option can take three
+Specify the type of write commands to issue. This option can take multiple
values:
.RS
.RS
.B write (default)
Write opcodes are issued as usual
.TP
+.B write_and_verify
+Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 00b. This directs the
+device to carry out a medium verification with no data comparison for the data
+that was written. The writefua option is ignored with this selection.
+.TP
.B verify
-Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 0. This
-directs the device to carry out a medium verification with no data
-comparison. The writefua option is ignored with this selection.
+This option is deprecated. Use write_and_verify instead.
.TP
-.B same
+.B write_same
Issue WRITE SAME commands. This transfers a single block to the device
and writes this same block of data to a contiguous sequence of LBAs
beginning at the specified offset. fio's block size parameter
generate 8k of data for each command butonly the first 512 bytes will
be used and transferred to the device. The writefua option is ignored
with this selection.
+.TP
+.B same
+This option is deprecated. Use write_same instead.
+.TP
+.B write_same_ndob
+Issue WRITE SAME(16) commands as above but with the No Data Output
+Buffer (NDOB) bit set. No data will be transferred to the device with
+this bit set. Data written will be a pre-determined pattern such as
+all zeroes.
+.TP
+.B write_stream
+Issue WRITE STREAM(16) commands. Use the stream_id option to specify
+the stream identifier.
+.TP
+.B verify_bytchk_00
+Issue VERIFY commands with BYTCHK set to 00. This directs the device to carry
+out a medium verification with no data comparison.
+.TP
+.B verify_bytchk_01
+Issue VERIFY commands with BYTCHK set to 01. This directs the device to
+compare the data on the device with the data transferred to the device.
+.TP
+.B verify_bytchk_11
+Issue VERIFY commands with BYTCHK set to 11. This transfers a single block to
+the device and compares the contents of this block with the data on the device
+beginning at the specified offset. fio's block size parameter specifies the
+total amount of data compared with this command. However, only one block
+(sector) worth of data is transferred to the device. This is similar to the
+WRITE SAME command except that data is compared instead of written.
.RE
.RE
.TP
+.BI (sg)stream_id \fR=\fPint
+Set the stream identifier for WRITE STREAM commands. If this is set to 0 (which is not
+a valid stream identifier) fio will open a stream and then close it when done. Default
+is 0.
+.TP
.BI (nbd)uri \fR=\fPstr
Specify the NBD URI of the server to test.
The string is a standard NBD URI (see
\fInbd+unix:///?socket=/tmp/socket\fR
.TP
\fInbds://tlshost/exportname\fR
-
+.RE
+.RE
+.TP
+.BI (libcufile)gpu_dev_ids\fR=\fPstr
+Specify the GPU IDs to use with CUDA. This is a colon-separated list of int.
+GPUs are assigned to workers roundrobin. Default is 0.
+.TP
+.BI (libcufile)cuda_io\fR=\fPstr
+Specify the type of I/O to use with CUDA. This option
+takes the following values:
+.RS
+.RS
+.TP
+.B cufile (default)
+Use libcufile and nvidia-fs. This option performs I/O directly
+between a GPUDirect Storage filesystem and GPU buffers,
+avoiding use of a bounce buffer. If \fBverify\fR is set,
+cudaMemcpy is used to copy verification data between RAM and GPU(s).
+Verification data is copied from RAM to GPU before a write
+and from GPU to RAM after a read.
+\fBdirect\fR must be 1.
+.TP
+.BI posix
+Use POSIX to perform I/O with a RAM buffer, and use
+cudaMemcpy to transfer data between RAM and the GPU(s).
+Data is copied from GPU to RAM before a write and copied
+from RAM to GPU after a read. \fBverify\fR does not affect
+the use of cudaMemcpy.
+.RE
+.RE
+.TP
+.BI (dfs)pool
+Specify the label or UUID of the DAOS pool to connect to.
+.TP
+.BI (dfs)cont
+Specify the label or UUID of the DAOS container to open.
+.TP
+.BI (dfs)chunk_size
+Specify a different chunk size (in bytes) for the dfs file.
+Use DAOS container's chunk size by default.
+.TP
+.BI (dfs)object_class
+Specify a different object class for the dfs file.
+Use DAOS container's object class by default.
+.TP
+.BI (nfs)nfs_url
+URL in libnfs format, eg nfs://<server|ipv4|ipv6>/path[?arg=val[&arg=val]*]
+Refer to the libnfs README for more details.
+.TP
+.BI (exec)program\fR=\fPstr
+Specify the program to execute.
+Note the program will receive a SIGTERM when the job is reaching the time limit.
+A SIGKILL is sent once the job is over. The delay between the two signals is defined by \fBgrace_time\fR option.
+.TP
+.BI (exec)arguments\fR=\fPstr
+Specify arguments to pass to program.
+Some special variables can be expanded to pass fio's job details to the program :
+.RS
+.RS
+.TP
+.B %r
+replaced by the duration of the job in seconds
+.TP
+.BI %n
+replaced by the name of the job
+.RE
+.RE
+.TP
+.BI (exec)grace_time\fR=\fPint
+Defines the time between the SIGTERM and SIGKILL signals. Default is 1 second.
+.TP
+.BI (exec)std_redirect\fR=\fPbool
+If set, stdout and stderr streams are redirected to files named from the job name. Default is true.
+.TP
+.BI (xnvme)xnvme_async\fR=\fPstr
+Select the xnvme async command interface. This can take these values.
+.RS
+.RS
+.TP
+.B emu
+This is default and use to emulate asynchronous I/O by using a single thread to
+create a queue pair on top of a synchronous I/O interface using the NVMe driver
+IOCTL.
+.TP
+.BI thrpool
+Emulate an asynchronous I/O interface with a pool of userspace threads on top
+of a synchronous I/O interface using the NVMe driver IOCTL. By default four
+threads are used.
+.TP
+.BI io_uring
+Linux native asynchronous I/O interface which supports both direct and buffered
+I/O.
+.TP
+.BI libaio
+Use Linux aio for Asynchronous I/O
+.TP
+.BI posix
+Use the posix asynchronous I/O interface to perform one or more I/O operations
+asynchronously.
+.TP
+.BI vfio
+Use the user-space VFIO-based backend, implemented using libvfn instead of
+SPDK.
+.TP
+.BI nil
+Do not transfer any data; just pretend to. This is mainly used for
+introspective performance evaluation.
+.RE
+.RE
+.TP
+.BI (xnvme)xnvme_sync\fR=\fPstr
+Select the xnvme synchronous command interface. This can take these values.
+.RS
+.RS
+.TP
+.B nvme
+This is default and uses Linux NVMe Driver ioctl() for synchronous I/O.
+.TP
+.BI psync
+This supports regular as well as vectored pread() and pwrite() commands.
+.TP
+.BI block
+This is the same as psync except that it also supports zone management
+commands using Linux block layer IOCTLs.
+.RE
+.RE
+.TP
+.BI (xnvme)xnvme_admin\fR=\fPstr
+Select the xnvme admin command interface. This can take these values.
+.RS
+.RS
+.TP
+.B nvme
+This is default and uses Linux NVMe Driver ioctl() for admin commands.
+.TP
+.BI block
+Use Linux Block Layer ioctl() and sysfs for admin commands.
+.RE
+.RE
+.TP
+.BI (xnvme)xnvme_dev_nsid\fR=\fPint
+xnvme namespace identifier for userspace NVMe driver SPDK or vfio.
+.TP
+.BI (xnvme)xnvme_dev_subnqn\fR=\fPstr
+Sets the subsystem NQN for fabrics. This is for xNVMe to utilize a fabrics
+target with multiple systems.
+.TP
+.BI (xnvme)xnvme_mem\fR=\fPstr
+Select the xnvme memory backend. This can take these values.
+.RS
+.RS
+.TP
+.B posix
+This is the default posix memory backend for linux NVMe driver.
+.TP
+.BI hugepage
+Use hugepages, instead of existing posix memory backend. The memory backend
+uses hugetlbfs. This require users to allocate hugepages, mount hugetlbfs and
+set an enviornment variable for XNVME_HUGETLB_PATH.
+.TP
+.BI spdk
+Uses SPDK's memory allocator.
+.TP
+.BI vfio
+Uses libvfn's memory allocator. This also specifies the use of libvfn backend
+instead of SPDK.
+.RE
+.RE
+.TP
+.BI (xnvme)xnvme_iovec
+If this option is set, xnvme will use vectored read/write commands.
+.TP
+.BI (libblkio)libblkio_driver \fR=\fPstr
+The libblkio driver to use. Different drivers access devices through different
+underlying interfaces. Available drivers depend on the libblkio version in use
+and are listed at \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
+.BI (libblkio)libblkio_path \fR=\fPstr
+Sets the value of the driver-specific "path" property before connecting the
+libblkio instance, which identifies the target device or file on which to
+perform I/O. Its exact semantics are driver-dependent and not all drivers may
+support it; see \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
+.BI (libblkio)libblkio_pre_connect_props \fR=\fPstr
+A colon-separated list of additional libblkio properties to be set after
+creating but before connecting the libblkio instance. Each property must have
+the format \fB<name>=<value>\fR. Colons can be escaped as \fB\\:\fR. These are
+set after the engine sets any other properties, so those can be overriden.
+Available properties depend on the libblkio version in use and are listed at
+\fIhttps://libblkio.gitlab.io/libblkio/blkio.html#properties\fR
+.TP
+.BI (libblkio)libblkio_num_entries \fR=\fPint
+Sets the value of the driver-specific "num-entries" property before starting the
+libblkio instance. Its exact semantics are driver-dependent and not all drivers
+may support it; see \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
+.BI (libblkio)libblkio_queue_size \fR=\fPint
+Sets the value of the driver-specific "queue-size" property before starting the
+libblkio instance. Its exact semantics are driver-dependent and not all drivers
+may support it; see \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
+.BI (libblkio)libblkio_pre_start_props \fR=\fPstr
+A colon-separated list of additional libblkio properties to be set after
+connecting but before starting the libblkio instance. Each property must have
+the format \fB<name>=<value>\fR. Colons can be escaped as \fB\\:\fR. These are
+set after the engine sets any other properties, so those can be overriden.
+Available properties depend on the libblkio version in use and are listed at
+\fIhttps://libblkio.gitlab.io/libblkio/blkio.html#properties\fR
+.TP
+.BI (libblkio)hipri
+Use poll queues. This is incompatible with \fBlibblkio_wait_mode=eventfd\fR and
+\fBlibblkio_force_enable_completion_eventfd\fR.
+.TP
+.BI (libblkio)libblkio_vectored
+Submit vectored read and write requests.
+.TP
+.BI (libblkio)libblkio_write_zeroes_on_trim
+Submit trims as "write zeroes" requests instead of discard requests.
+.TP
+.BI (libblkio)libblkio_wait_mode \fR=\fPstr
+How to wait for completions:
+.RS
+.RS
+.TP
+.B block \fR(default)
+Use a blocking call to \fBblkioq_do_io()\fR.
+.TP
+.B eventfd
+Use a blocking call to \fBread()\fR on the completion eventfd.
+.TP
+.B loop
+Use a busy loop with a non-blocking call to \fBblkioq_do_io()\fR.
+.RE
+.RE
+.TP
+.BI (libblkio)libblkio_force_enable_completion_eventfd
+Enable the queue's completion eventfd even when unused. This may impact
+performance. The default is to enable it only if
+\fBlibblkio_wait_mode=eventfd\fR.
.SS "I/O depth"
.TP
.BI iodepth \fR=\fPint
can increase latencies. The benefit is that fio can manage submission rates
independently of the device completion rates. This avoids skewed latency
reporting if I/O gets backed up on the device side (the coordinated omission
-problem).
+problem). Note that this option cannot reliably be used with async IO engines.
.SS "I/O rate"
.TP
.BI thinktime \fR=\fPtime
Stall the job for the specified period of time after an I/O has completed before issuing the
next. May be used to simulate processing being done by an application.
When the unit is omitted, the value is interpreted in microseconds. See
-\fBthinktime_blocks\fR and \fBthinktime_spin\fR.
+\fBthinktime_blocks\fR, \fBthinktime_iotime\fR and \fBthinktime_spin\fR.
.TP
.BI thinktime_spin \fR=\fPtime
Only valid if \fBthinktime\fR is set - pretend to spend CPU time doing
queue depth setting redundant, since no more than 1 I/O will be queued
before we have to complete it and do our \fBthinktime\fR. In other words, this
setting effectively caps the queue depth if the latter is larger.
+.TP
+.BI thinktime_blocks_type \fR=\fPstr
+Only valid if \fBthinktime\fR is set - control how \fBthinktime_blocks\fR triggers.
+The default is `complete', which triggers \fBthinktime\fR when fio completes
+\fBthinktime_blocks\fR blocks. If this is set to `issue', then the trigger happens
+at the issue side.
+.TP
+.BI thinktime_iotime \fR=\fPtime
+Only valid if \fBthinktime\fR is set - control \fBthinktime\fR interval by time.
+The \fBthinktime\fR stall is repeated after IOs are executed for
+\fBthinktime_iotime\fR. For example, `\-\-thinktime_iotime=9s \-\-thinktime=1s'
+repeat 10-second cycle with IOs for 9 seconds and stall for 1 second. When the
+unit is omitted, \fBthinktime_iotime\fR is interpreted as a number of seconds.
+If this option is used together with \fBthinktime_blocks\fR, the \fBthinktime\fR
+stall is repeated after \fBthinktime_iotime\fR or after \fBthinktime_blocks\fR
+IOs, whichever happens first.
+
.TP
.BI rate \fR=\fPint[,int][,int]
Cap the bandwidth used by this job. The number is in bytes/sec, the normal
defaults to 100.0, meaning that all I/Os must be equal or below to the value
set by \fBlatency_target\fR.
.TP
-.BI max_latency \fR=\fPtime
+.BI latency_run \fR=\fPbool
+Used with \fBlatency_target\fR. If false (default), fio will find the highest
+queue depth that meets \fBlatency_target\fR and exit. If true, fio will continue
+running and try to meet \fBlatency_target\fR by adjusting queue depth.
+.TP
+.BI max_latency \fR=\fPtime[,time][,time]
If set, fio will exit the job with an ETIMEDOUT error if it exceeds this
maximum latency. When the unit is omitted, the value is interpreted in
-microseconds.
+microseconds. Comma-separated values may be specified for reads, writes,
+and trims as described in \fBblocksize\fR.
.TP
.BI rate_cycle \fR=\fPint
Average bandwidth for \fBrate\fR and \fBrate_min\fR over this number
.BI write_iolog \fR=\fPstr
Write the issued I/O patterns to the specified file. See
\fBread_iolog\fR. Specify a separate file for each job, otherwise the
-iologs will be interspersed and the file may be corrupt.
+iologs will be interspersed and the file may be corrupt. This file will be
+opened in append mode.
.TP
.BI read_iolog \fR=\fPstr
Open an iolog with the specified filename and replay the I/O patterns it
replay, the file needs to be turned into a blkparse binary data file first
(`blkparse <device> \-o /dev/null \-d file_for_fio.bin').
You can specify a number of files by separating the names with a ':' character.
-See the \fBfilename\fR option for information on how to escape ':' and '\'
+See the \fBfilename\fR option for information on how to escape ':'
characters within the file names. These files will be sequentially assigned to
-job clones created by \fBnumjobs\fR.
+job clones created by \fBnumjobs\fR. '-' is a reserved name, meaning read from
+stdin, notably if \fBfilename\fR is set to '-' which means stdin as well,
+then this flag can't be set to '-'.
.TP
.BI read_iolog_chunked \fR=\fPbool
Determines how iolog is read. If false (default) entire \fBread_iolog\fR will
Set the I/O priority value of this job. Linux limits us to a positive value
between 0 and 7, with 0 being the highest. See man
\fBionice\fR\|(1). Refer to an appropriate manpage for other operating
-systems since meaning of priority may differ.
+systems since meaning of priority may differ. For per-command priority
+setting, see the I/O engine specific `cmdprio_percentage` and
+`cmdprio` options.
.TP
.BI prioclass \fR=\fPint
-Set the I/O priority class. See man \fBionice\fR\|(1).
+Set the I/O priority class. See man \fBionice\fR\|(1). For per-command
+priority setting, see the I/O engine specific `cmdprio_percentage` and
+`cmdprio_class` options.
.TP
.BI cpus_allowed \fR=\fPstr
Controls the same options as \fBcpumask\fR, but accepts a textual
flow. See \fBflow\fR.
.TP
.BI flow \fR=\fPint
-Weight in token-based flow control. If this value is used, then there is
-a 'flow counter' which is used to regulate the proportion of activity between
-two or more jobs. Fio attempts to keep this flow counter near zero. The
-\fBflow\fR parameter stands for how much should be added or subtracted to the
-flow counter on each iteration of the main I/O loop. That is, if one job has
-`flow=8' and another job has `flow=\-1', then there will be a roughly 1:8
-ratio in how much one runs vs the other.
-.TP
-.BI flow_watermark \fR=\fPint
-The maximum value that the absolute value of the flow counter is allowed to
-reach before the job must wait for a lower value of the counter.
+Weight in token-based flow control. If this value is used,
+then fio regulates the activity between two or more jobs
+sharing the same flow_id.
+Fio attempts to keep each job activity proportional to other jobs' activities
+in the same flow_id group, with respect to requested weight per job.
+That is, if one job has `flow=3', another job has `flow=2'
+and another with `flow=1`, then there will be a roughly 3:2:1 ratio
+in how much one runs vs the others.
.TP
.BI flow_sleep \fR=\fPint
-The period of time, in microseconds, to wait after the flow watermark has
-been exceeded before retrying operations.
+The period of time, in microseconds, to wait after the flow counter
+has exceeded its proportion before retrying operations.
.TP
.BI stonewall "\fR,\fB wait_for_previous"
Wait for preceding jobs in the job file to exit, before starting this
one. Can be used to insert serialization points in the job file. A stone
wall also implies starting a new reporting group, see
-\fBgroup_reporting\fR.
+\fBgroup_reporting\fR. Optionally you can use `stonewall=0` to disable or
+`stonewall=1` to enable it.
.TP
.BI exitall
By default, fio will continue running all other jobs when one job finishes.
make fio terminate all jobs in the same group, as soon as one job of that
group finishes.
.TP
-.BI exit_what
+.BI exit_what \fR=\fPstr
By default, fio will continue running all other jobs when one job finishes.
-Sometimes this is not the desired action. Setting \fBexit_all\fR will instead
+Sometimes this is not the desired action. Setting \fBexitall\fR will instead
make fio terminate all jobs in the same group. The option \fBexit_what\fR
-allows to control which jobs get terminated when \fBexitall\fR is enabled. The
-default is \fBgroup\fR and does not change the behaviour of \fBexitall\fR. The
-setting \fBall\fR terminates all jobs. The setting \fBstonewall\fR terminates
-all currently running jobs across all groups and continues execution with the
-next stonewalled group.
+allows you to control which jobs get terminated when \fBexitall\fR is enabled.
+The default value is \fBgroup\fR.
+The allowed values are:
+.RS
+.RS
+.TP
+.B all
+terminates all jobs.
+.TP
+.B group
+is the default and does not change the behaviour of \fBexitall\fR.
+.TP
+.B stonewall
+terminates all currently running jobs across all groups and continues
+execution with the next stonewalled group.
+.RE
+.RE
.TP
.BI exec_prerun \fR=\fPstr
Before running this job, issue the command specified through
To avoid false verification errors, do not use the norandommap option when
verifying data with async I/O engines and I/O depths > 1. Or use the
norandommap and the lfsr random generator together to avoid writing to the
-same offset with muliple outstanding I/Os.
+same offset with multiple outstanding I/Os.
.RE
.TP
.BI verify_offset \fR=\fPint
Trim this number of I/O blocks.
.TP
.BI experimental_verify \fR=\fPbool
-Enable experimental verification.
+Enable experimental verification. Standard verify records I/O metadata for
+later use during the verification phase. Experimental verify instead resets the
+file after the write phase and then replays I/Os for the verification phase.
.SS "Steady state"
.TP
.BI steadystate \fR=\fPstr:float "\fR,\fP ss" \fR=\fPstr:float
\fBwrite_bw_log\fR for details about the filename format and \fBLOG
FILE FORMATS\fR for how data is structured within the file.
.TP
+.BI log_entries \fR=\fPint
+By default, fio will log an entry in the iops, latency, or bw log for
+every I/O that completes. The initial number of I/O log entries is 1024.
+When the log entries are all used, new log entries are dynamically
+allocated. This dynamic log entry allocation may negatively impact
+time-related statistics such as I/O tail latencies (e.g. 99.9th percentile
+completion latency). This option allows specifying a larger initial
+number of log entries to avoid run-time allocation of new log entries,
+resulting in more precise time-related I/O statistics.
+Also see \fBlog_avg_msec\fR as well. Defaults to 1024.
+.TP
.BI log_avg_msec \fR=\fPint
By default, fio will log an entry in the iops, latency, or bw log for every
I/O that completes. When writing to the disk log, that can quickly grow to a
entry as well as the other data values. Defaults to 0 meaning that
offsets are not present in logs. Also see \fBLOG FILE FORMATS\fR section.
.TP
+.BI log_prio \fR=\fPbool
+If this is set, the iolog options will include the I/O priority for the I/O
+entry as well as the other data values. Defaults to 0 meaning that
+I/O priorities are not present in logs. Also see \fBLOG FILE FORMATS\fR section.
+.TP
.BI log_compression \fR=\fPint
If this is set, fio will compress the I/O logs as it goes, to keep the
memory footprint lower. When a log reaches the specified size, that chunk is
write_type_log for each log type, instead of the default zero-based
timestamps.
.TP
+.BI log_alternate_epoch \fR=\fPbool
+If set, fio will log timestamps based on the epoch used by the clock specified
+in the \fBlog_alternate_epoch_clock_id\fR option, to the log files produced by
+enabling write_type_log for each log type, instead of the default zero-based
+timestamps.
+.TP
+.BI log_alternate_epoch_clock_id \fR=\fPint
+Specifies the clock_id to be used by clock_gettime to obtain the alternate epoch
+if either \fBBlog_unix_epoch\fR or \fBlog_alternate_epoch\fR are true. Otherwise has no
+effect. Default value is 0, or CLOCK_REALTIME.
+.TP
.BI block_error_percentiles \fR=\fPbool
If set, record errors in trim block-sized units from writes and trims and
output a histogram of how many trims it took to get to errors, and what kind
Disable measurements of throughput/bandwidth numbers. See
\fBdisable_lat\fR.
.TP
+.BI slat_percentiles \fR=\fPbool
+Report submission latency percentiles. Submission latency is not recorded
+for synchronous ioengines.
+.TP
.BI clat_percentiles \fR=\fPbool
-Enable the reporting of percentiles of completion latencies. This option is
-mutually exclusive with \fBlat_percentiles\fR.
+Report completion latency percentiles.
.TP
.BI lat_percentiles \fR=\fPbool
-Enable the reporting of percentiles of I/O latencies. This is similar to
-\fBclat_percentiles\fR, except that this includes the submission latency.
-This option is mutually exclusive with \fBclat_percentiles\fR.
+Report total latency percentiles. Total latency is the sum of submission
+latency and completion latency.
.TP
.BI percentile_list \fR=\fPfloat_list
-Overwrite the default list of percentiles for completion latencies and the
-block error histogram. Each number is a floating number in the range
+Overwrite the default list of percentiles for latencies and the
+block error histogram. Each number is a floating point number in the range
(0,100], and the maximum length of the list is 20. Use ':' to separate the
-numbers, and list the numbers in ascending order. For example,
-`\-\-percentile_list=99.5:99.9' will cause fio to report the values of
-completion latency below which 99.5% and 99.9% of the observed latencies
-fell, respectively.
+numbers. For example, `\-\-percentile_list=99.5:99.9' will cause fio to
+report the latency durations below which 99.5% and 99.9% of the observed
+latencies fell, respectively.
.TP
.BI significant_figures \fR=\fPint
If using \fB\-\-output\-format\fR of `normal', set the significant figures
completed. If this option is used, there are two more stats that are
appended, the total error count and the first error. The error field given
in the stats is the first error that was hit during the run.
+.RS
+.P
+Note: a write error from the device may go unnoticed by fio when using buffered
+IO, as the write() (or similar) system call merely dirties the kernel pages,
+unless `sync' or `direct' is used. Device IO errors occur when the dirty data is
+actually written out to disk. If fully sync writes aren't desirable, `fsync' or
+`fdatasync' can be used as well. This is specific to writes, as reads are always
+synchronous.
+.RS
+.P
The allowed values are:
.RS
.RS
minimal output v3, separated by semicolons:
.P
.nf
- terse_version_3;fio_version;jobname;groupid;error;read_kb;read_bandwidth;read_iops;read_runtime_ms;read_slat_min;read_slat_max;read_slat_mean;read_slat_dev;read_clat_min;read_clat_max;read_clat_mean;read_clat_dev;read_clat_pct01;read_clat_pct02;read_clat_pct03;read_clat_pct04;read_clat_pct05;read_clat_pct06;read_clat_pct07;read_clat_pct08;read_clat_pct09;read_clat_pct10;read_clat_pct11;read_clat_pct12;read_clat_pct13;read_clat_pct14;read_clat_pct15;read_clat_pct16;read_clat_pct17;read_clat_pct18;read_clat_pct19;read_clat_pct20;read_tlat_min;read_lat_max;read_lat_mean;read_lat_dev;read_bw_min;read_bw_max;read_bw_agg_pct;read_bw_mean;read_bw_dev;write_kb;write_bandwidth;write_iops;write_runtime_ms;write_slat_min;write_slat_max;write_slat_mean;write_slat_dev;write_clat_min;write_clat_max;write_clat_mean;write_clat_dev;write_clat_pct01;write_clat_pct02;write_clat_pct03;write_clat_pct04;write_clat_pct05;write_clat_pct06;write_clat_pct07;write_clat_pct08;write_clat_pct09;write_clat_pct10;write_clat_pct11;write_clat_pct12;write_clat_pct13;write_clat_pct14;write_clat_pct15;write_clat_pct16;write_clat_pct17;write_clat_pct18;write_clat_pct19;write_clat_pct20;write_tlat_min;write_lat_max;write_lat_mean;write_lat_dev;write_bw_min;write_bw_max;write_bw_agg_pct;write_bw_mean;write_bw_dev;cpu_user;cpu_sys;cpu_csw;cpu_mjf;cpu_minf;iodepth_1;iodepth_2;iodepth_4;iodepth_8;iodepth_16;iodepth_32;iodepth_64;lat_2us;lat_4us;lat_10us;lat_20us;lat_50us;lat_100us;lat_250us;lat_500us;lat_750us;lat_1000us;lat_2ms;lat_4ms;lat_10ms;lat_20ms;lat_50ms;lat_100ms;lat_250ms;lat_500ms;lat_750ms;lat_1000ms;lat_2000ms;lat_over_2000ms;disk_name;disk_read_iops;disk_write_iops;disk_read_merges;disk_write_merges;disk_read_ticks;write_ticks;disk_queue_time;disk_util
+ terse_version_3;fio_version;jobname;groupid;error;read_kb;read_bandwidth_kb;read_iops;read_runtime_ms;read_slat_min_us;read_slat_max_us;read_slat_mean_us;read_slat_dev_us;read_clat_min_us;read_clat_max_us;read_clat_mean_us;read_clat_dev_us;read_clat_pct01;read_clat_pct02;read_clat_pct03;read_clat_pct04;read_clat_pct05;read_clat_pct06;read_clat_pct07;read_clat_pct08;read_clat_pct09;read_clat_pct10;read_clat_pct11;read_clat_pct12;read_clat_pct13;read_clat_pct14;read_clat_pct15;read_clat_pct16;read_clat_pct17;read_clat_pct18;read_clat_pct19;read_clat_pct20;read_tlat_min_us;read_lat_max_us;read_lat_mean_us;read_lat_dev_us;read_bw_min_kb;read_bw_max_kb;read_bw_agg_pct;read_bw_mean_kb;read_bw_dev_kb;write_kb;write_bandwidth_kb;write_iops;write_runtime_ms;write_slat_min_us;write_slat_max_us;write_slat_mean_us;write_slat_dev_us;write_clat_min_us;write_clat_max_us;write_clat_mean_us;write_clat_dev_us;write_clat_pct01;write_clat_pct02;write_clat_pct03;write_clat_pct04;write_clat_pct05;write_clat_pct06;write_clat_pct07;write_clat_pct08;write_clat_pct09;write_clat_pct10;write_clat_pct11;write_clat_pct12;write_clat_pct13;write_clat_pct14;write_clat_pct15;write_clat_pct16;write_clat_pct17;write_clat_pct18;write_clat_pct19;write_clat_pct20;write_tlat_min_us;write_lat_max_us;write_lat_mean_us;write_lat_dev_us;write_bw_min_kb;write_bw_max_kb;write_bw_agg_pct;write_bw_mean_kb;write_bw_dev_kb;cpu_user;cpu_sys;cpu_csw;cpu_mjf;cpu_minf;iodepth_1;iodepth_2;iodepth_4;iodepth_8;iodepth_16;iodepth_32;iodepth_64;lat_2us;lat_4us;lat_10us;lat_20us;lat_50us;lat_100us;lat_250us;lat_500us;lat_750us;lat_1000us;lat_2ms;lat_4ms;lat_10ms;lat_20ms;lat_50ms;lat_100ms;lat_250ms;lat_500ms;lat_750ms;lat_1000ms;lat_2000ms;lat_over_2000ms;disk_name;disk_read_iops;disk_write_iops;disk_read_merges;disk_write_merges;disk_read_ticks;write_ticks;disk_queue_time;disk_util
.fi
.P
In client/server mode terse output differs from what appears when jobs are run
.TP
.B Trace file format v2
The second version of the trace file format was added in fio version 1.17. It
-allows to access more then one file per trace and has a bigger set of possible
+allows one to access more than one file per trace and has a bigger set of possible
file actions.
.RS
.P
.TP
.B wait
Wait for `offset' microseconds. Everything below 100 is discarded.
-The time is relative to the previous `wait' statement.
+The time is relative to the previous `wait' statement. Note that action `wait`
+is not allowed as of version 3, as the same behavior can be achieved using
+timestamps.
.TP
.B read
Read `length' bytes beginning from `offset'.
Trim the given file from the given `offset' for `length' bytes.
.RE
.RE
+.RE
+.TP
+.B Trace file format v3
+The third version of the trace file format was added in fio version 3.31. It
+forces each action to have a timestamp associated with it.
+.RS
+.P
+The first line of the trace file has to be:
+.RS
+.P
+"fio version 3 iolog"
+.RE
+.P
+Following this can be lines in two different formats, which are described below.
+.P
+.B
+The file management format:
+.RS
+timestamp filename action
+.P
+.RE
+.B
+The file I/O action format:
+.RS
+timestamp filename action offset length
+.P
+The `timestamp` is relative to the beginning of the run (ie starts at 0). The
+`filename`, `action`, `offset` and `length` are identical to version 2, except
+that version 3 does not allow the `wait` action.
+.RE
+.RE
.SH I/O REPLAY \- MERGING TRACES
Colocation is a common practice used to get the most out of a machine.
Knowing which workloads play nicely with each other and which ones don't is
and IOPS. The logs share a common format, which looks like this:
.RS
.P
-time (msec), value, data direction, block size (bytes), offset (bytes)
+time (msec), value, data direction, block size (bytes), offset (bytes),
+command priority
.RE
.P
`Time' for the log entry is always in milliseconds. The `value' logged depends
from the start of the file for that particular I/O. The logging of the offset can be
toggled with \fBlog_offset\fR.
.P
+If \fBlog_prio\fR is not set, the entry's `Command priority` is 1 for an IO executed
+with the highest RT priority class (\fBprioclass\fR=1 or \fBcmdprio_class\fR=1) and 0
+otherwise. This is controlled by the \fBprioclass\fR option and the ioengine specific
+\fBcmdprio_percentage\fR \fBcmdprio_class\fR options. If \fBlog_prio\fR is set, the
+entry's `Command priority` is the priority set for the IO, as a 16-bits hexadecimal
+number with the lowest 13 bits indicating the priority value (\fBprio\fR and
+\fBcmdprio\fR options) and the highest 3 bits indicating the IO priority class
+(\fBprioclass\fR and \fBcmdprio_class\fR options).
+.P
Fio defaults to logging every individual I/O but when windowed logging is set
through \fBlog_avg_msec\fR, either the average (by default) or the maximum
(\fBlog_max_value\fR is set) `value' seen over the specified period of time
projects / fio.git / blobdiff