.SS "Time related parameters"
.TP
.BI runtime \fR=\fPtime
-Tell fio to terminate processing after the specified period of time. It
-can be quite hard to determine for how long a specified job will run, so
-this parameter is handy to cap the total runtime to a given time. When
-the unit is omitted, the value is interpreted in seconds.
+Limit runtime. The test will run until it completes the configured I/O
+workload or until it has run for this specified amount of time, whichever
+occurs first. It can be quite hard to determine for how long a specified
+job will run, so this parameter is handy to cap the total runtime to a
+given time. When the unit is omitted, the value is interpreted in
+seconds.
.TP
.BI time_based
If set, fio will run for the duration of the \fBruntime\fR specified
so. Default: false.
.TP
.BI max_open_zones \fR=\fPint
-When running a random write test across an entire drive many more zones will be
-open than in a typical application workload. Hence this command line option
-that allows one to limit the number of open zones. The number of open zones is
-defined as the number of zones to which write commands are issued by all
-threads/processes.
+A zone of a zoned block device is in the open state when it is partially written
+(i.e. not all sectors of the zone have been written). Zoned block devices may
+have limit a on the total number of zones that can be simultaneously in the
+open state, that is, the number of zones that can be written to simultaneously.
+The \fBmax_open_zones\fR parameter limits the number of zones to which write
+commands are issued by all fio jobs, that is, limits the number of zones that
+will be in the open state. This parameter is relevant only if the
+\fBzonemode=zbd\fR is used. The default value is always equal to maximum number
+of open zones of the target zoned block device and a value higher than this
+limit cannot be specified by users unless the option \fBignore_zone_limits\fR is
+specified. When \fBignore_zone_limits\fR is specified or the target device has
+no limit on the number of zones that can be in an open state,
+\fBmax_open_zones\fR can specify 0 to disable any limit on the number of zones
+that can be simultaneously written to by all jobs.
.TP
.BI job_max_open_zones \fR=\fPint
-Limit on the number of simultaneously opened zones per single thread/process.
+In the same manner as \fBmax_open_zones\fR, limit the number of open zones per
+fio job, that is, the number of zones that a single job can simultaneously write
+to. A value of zero indicates no limit. Default: zero.
.TP
.BI ignore_zone_limits \fR=\fPbool
If this option is used, fio will ignore the maximum number of open zones limit
value to be larger than the device reported limit. Default: false.
.TP
.BI zone_reset_threshold \fR=\fPfloat
-A number between zero and one that indicates the ratio of logical blocks with
-data to the total number of logical blocks in the test above which zones
-should be reset periodically.
+A number between zero and one that indicates the ratio of written bytes in the
+zones with write pointers in the IO range to the size of the IO range. When
+current ratio is above this ratio, zones are reset periodically as
+\fBzone_reset_frequency\fR specifies. If there are multiple jobs when using this
+option, the IO range for all write jobs has to be the same.
.TP
.BI zone_reset_frequency \fR=\fPfloat
A number between zero and one that indicates how often a zone reset should be
OpenBSD and ZFS on Solaris don't support direct I/O. On Windows the synchronous
ioengines don't support direct I/O. Default: false.
.TP
-.BI atomic \fR=\fPbool
-If value is true, attempt to use atomic direct I/O. Atomic writes are
-guaranteed to be stable once acknowledged by the operating system. Only
-Linux supports O_ATOMIC right now.
-.TP
.BI buffered \fR=\fPbool
If value is true, use buffered I/O. This is the opposite of the
\fBdirect\fR option. Defaults to true.
.P
\fBsequential\fR is only useful for random I/O, where fio would normally
generate a new random offset for every I/O. If you append e.g. 8 to randread,
-you would get a new random offset for every 8 I/Os. The result would be a
-seek for only every 8 I/Os, instead of for every I/O. Use `rw=randread:8'
-to specify that. As sequential I/O is already sequential, setting
-\fBsequential\fR for that would not result in any differences. \fBidentical\fR
-behaves in a similar fashion, except it sends the same offset 8 number of
-times before generating a new offset.
+i.e. `rw=randread:8' you would get a new random offset for every 8 I/Os. The
+result would be a sequence of 8 sequential offsets with a random starting
+point. However this behavior may change if a sequential I/O reaches end of the
+file. As sequential I/O is already sequential, setting \fBsequential\fR for
+that would not result in any difference. \fBidentical\fR behaves in a similar
+fashion, except it sends the same offset 8 number of times before generating a
+new offset.
+.P
+.P
+Example #1:
+.RS
+.P
+.PD 0
+rw=randread:8
+.P
+rw_sequencer=sequential
+.P
+bs=4k
+.PD
+.RE
+.P
+The generated sequence of offsets will look like this:
+4k, 8k, 12k, 16k, 20k, 24k, 28k, 32k, 92k, 96k, 100k, 104k, 108k, 112k, 116k,
+120k, 48k, 52k ...
+.P
+.P
+Example #2:
+.RS
+.P
+.PD 0
+rw=randread:8
+.P
+rw_sequencer=identical
+.P
+bs=4k
+.PD
+.RE
+.P
+The generated sequence of offsets will look like this:
+4k, 4k, 4k, 4k, 4k, 4k, 4k, 4k, 92k, 92k, 92k, 92k, 92k, 92k, 92k, 92k, 48k,
+48k, 48k ...
.RE
.TP
.BI unified_rw_reporting \fR=\fPstr
.RE
.TP
.BI randrepeat \fR=\fPbool
-Seed the random number generator used for random I/O patterns in a
-predictable way so the pattern is repeatable across runs. Default: true.
+Seed all random number generators in a predictable way so the pattern is
+repeatable across runs. Default: true.
.TP
.BI allrandrepeat \fR=\fPbool
-Seed all random number generators in a predictable way so results are
-repeatable across runs. Default: false.
+Alias for \fBrandrepeat\fR. Default: true.
.TP
.BI randseed \fR=\fPint
Seed the random number generators based on this seed value, to be able to
.TP
.B random
Advise using FADV_RANDOM.
+.TP
+.B noreuse
+Advise using FADV_NOREUSE. This may be a no-op on older Linux
+kernels. Since Linux 6.3, it provides a hint to the LRU algorithm.
+See the \fBposix_fadvise\fR\|(2) man page.
.RE
.RE
.TP
before overwriting. The \fBtrimwrite\fR mode works well for this
constraint.
.TP
-.B pmemblk
-Read and write using filesystem DAX to a file on a filesystem
-mounted with DAX on a persistent memory device through the PMDK
-libpmemblk library.
-.TP
.B dev\-dax
Read and write using device DAX to a persistent memory device (e.g.,
/dev/dax0.0) through the PMDK libpmem library.
.TP
.B libblkio
Use the libblkio library (\fIhttps://gitlab.com/libblkio/libblkio\fR). The
-specific driver to use must be set using \fBlibblkio_driver\fR.
+specific driver to use must be set using \fBlibblkio_driver\fR. If
+\fBmem\fR/\fBiomem\fR is not specified, memory allocation is delegated to
+libblkio (and so is guaranteed to work with the selected driver). One libblkio
+instance is used per process, so all jobs setting option \fBthread\fR will share
+a single instance (with one queue per thread) and must specify compatible
+options. Note that some drivers don't allow several instances to access the same
+device or file simultaneously, but allow it for threads.
.SS "I/O engine specific parameters"
In addition, there are some parameters which are only valid when a specific
\fBioengine\fR is in use. These are used identically to normal parameters,
For direct I/O, requests will only succeed if cache invalidation isn't required,
file blocks are fully allocated and the disk request could be issued immediately.
.TP
+.BI (io_uring_cmd)fdp \fR=\fPbool
+Enable Flexible Data Placement mode for write commands.
+.TP
+.BI (io_uring_cmd)fdp_pli \fR=\fPstr
+Select which Placement ID Index/Indicies this job is allowed to use for writes.
+By default, the job will cycle through all available Placement IDs, so use this
+to isolate these identifiers to specific jobs. If you want fio to use placement
+identifier only at indices 0, 2 and 5 specify, you would set `fdp_pli=0,2,5`.
+.TP
.BI (cpuio)cpuload \fR=\fPint
Attempt to use the specified percentage of CPU cycles. This is a mandatory
option when using cpuio I/O engine.
.BI (exec)grace_time\fR=\fPint
Defines the time between the SIGTERM and SIGKILL signals. Default is 1 second.
.TP
-.BI (exec)std_redirect\fR=\fbool
+.BI (exec)std_redirect\fR=\fPbool
If set, stdout and stderr streams are redirected to files named from the job name. Default is true.
.TP
.BI (xnvme)xnvme_async\fR=\fPstr
Use the posix asynchronous I/O interface to perform one or more I/O operations
asynchronously.
.TP
+.BI vfio
+Use the user-space VFIO-based backend, implemented using libvfn instead of
+SPDK.
+.TP
.BI nil
Do not transfer any data; just pretend to. This is mainly used for
introspective performance evaluation.
.RE
.TP
.BI (xnvme)xnvme_dev_nsid\fR=\fPint
-xnvme namespace identifier for userspace NVMe driver such as SPDK.
+xnvme namespace identifier for userspace NVMe driver SPDK or vfio.
+.TP
+.BI (xnvme)xnvme_dev_subnqn\fR=\fPstr
+Sets the subsystem NQN for fabrics. This is for xNVMe to utilize a fabrics
+target with multiple systems.
+.TP
+.BI (xnvme)xnvme_mem\fR=\fPstr
+Select the xnvme memory backend. This can take these values.
+.RS
+.RS
+.TP
+.B posix
+This is the default posix memory backend for linux NVMe driver.
+.TP
+.BI hugepage
+Use hugepages, instead of existing posix memory backend. The memory backend
+uses hugetlbfs. This require users to allocate hugepages, mount hugetlbfs and
+set an enviornment variable for XNVME_HUGETLB_PATH.
+.TP
+.BI spdk
+Uses SPDK's memory allocator.
+.TP
+.BI vfio
+Uses libvfn's memory allocator. This also specifies the use of libvfn backend
+instead of SPDK.
+.RE
+.RE
.TP
.BI (xnvme)xnvme_iovec
If this option is set, xnvme will use vectored read/write commands.
underlying interfaces. Available drivers depend on the libblkio version in use
and are listed at \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
.TP
+.BI (libblkio)libblkio_path \fR=\fPstr
+Sets the value of the driver-specific "path" property before connecting the
+libblkio instance, which identifies the target device or file on which to
+perform I/O. Its exact semantics are driver-dependent and not all drivers may
+support it; see \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
.BI (libblkio)libblkio_pre_connect_props \fR=\fPstr
-A colon-separated list of libblkio properties to be set after creating but
-before connecting the libblkio instance. Each property must have the format
-\fB<name>=<value>\fR. Colons can be escaped as \fB\\:\fR. These are set after
-the engine sets any other properties, so those can be overriden. Available
-properties depend on the libblkio version in use and are listed at
+A colon-separated list of additional libblkio properties to be set after
+creating but before connecting the libblkio instance. Each property must have
+the format \fB<name>=<value>\fR. Colons can be escaped as \fB\\:\fR. These are
+set after the engine sets any other properties, so those can be overriden.
+Available properties depend on the libblkio version in use and are listed at
\fIhttps://libblkio.gitlab.io/libblkio/blkio.html#properties\fR
.TP
+.BI (libblkio)libblkio_num_entries \fR=\fPint
+Sets the value of the driver-specific "num-entries" property before starting the
+libblkio instance. Its exact semantics are driver-dependent and not all drivers
+may support it; see \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
+.BI (libblkio)libblkio_queue_size \fR=\fPint
+Sets the value of the driver-specific "queue-size" property before starting the
+libblkio instance. Its exact semantics are driver-dependent and not all drivers
+may support it; see \fIhttps://libblkio.gitlab.io/libblkio/blkio.html#drivers\fR
+.TP
.BI (libblkio)libblkio_pre_start_props \fR=\fPstr
-A colon-separated list of libblkio properties to be set after connecting but
-before starting the libblkio instance. Each property must have the format
-\fB<name>=<value>\fR. Colons can be escaped as \fB\\:\fR. These are set after
-the engine sets any other properties, so those can be overriden. Available
-properties depend on the libblkio version in use and are listed at
+A colon-separated list of additional libblkio properties to be set after
+connecting but before starting the libblkio instance. Each property must have
+the format \fB<name>=<value>\fR. Colons can be escaped as \fB\\:\fR. These are
+set after the engine sets any other properties, so those can be overriden.
+Available properties depend on the libblkio version in use and are listed at
\fIhttps://libblkio.gitlab.io/libblkio/blkio.html#properties\fR
+.TP
+.BI (libblkio)hipri
+Use poll queues. This is incompatible with \fBlibblkio_wait_mode=eventfd\fR and
+\fBlibblkio_force_enable_completion_eventfd\fR.
+.TP
+.BI (libblkio)libblkio_vectored
+Submit vectored read and write requests.
+.TP
+.BI (libblkio)libblkio_write_zeroes_on_trim
+Submit trims as "write zeroes" requests instead of discard requests.
+.TP
+.BI (libblkio)libblkio_wait_mode \fR=\fPstr
+How to wait for completions:
+.RS
+.RS
+.TP
+.B block \fR(default)
+Use a blocking call to \fBblkioq_do_io()\fR.
+.TP
+.B eventfd
+Use a blocking call to \fBread()\fR on the completion eventfd.
+.TP
+.B loop
+Use a busy loop with a non-blocking call to \fBblkioq_do_io()\fR.
+.RE
+.RE
+.TP
+.BI (libblkio)libblkio_force_enable_completion_eventfd
+Enable the queue's completion eventfd even when unused. This may impact
+performance. The default is to enable it only if
+\fBlibblkio_wait_mode=eventfd\fR.
+.TP
+.BI (windowsaio)no_completion_thread
+Avoid using a separate thread for completion polling.
.SS "I/O depth"
.TP
.BI iodepth \fR=\fPint
kind of thinktime setting was used. If this option is set, then fio will
ignore the thinktime and continue doing IO at the specified rate, instead of
entering a catch-up mode after thinktime is done.
+.TP
+.BI rate_cycle \fR=\fPint
+Average bandwidth for \fBrate\fR and \fBrate_min\fR over this number
+of milliseconds. Defaults to 1000.
.SS "I/O latency"
.TP
.BI latency_target \fR=\fPtime
maximum latency. When the unit is omitted, the value is interpreted in
microseconds. Comma-separated values may be specified for reads, writes,
and trims as described in \fBblocksize\fR.
-.TP
-.BI rate_cycle \fR=\fPint
-Average bandwidth for \fBrate\fR and \fBrate_min\fR over this number
-of milliseconds. Defaults to 1000.
.SS "I/O replay"
.TP
.BI write_iolog \fR=\fPstr
verification pass, according to the settings in the job file used. Default
false.
.TP
+.BI experimental_verify \fR=\fPbool
+Enable experimental verification. Standard verify records I/O metadata for
+later use during the verification phase. Experimental verify instead resets the
+file after the write phase and then replays I/Os for the verification phase.
+.TP
.BI trim_percentage \fR=\fPint
Number of verify blocks to discard/trim.
.TP
.TP
.BI trim_backlog_batch \fR=\fPint
Trim this number of I/O blocks.
-.TP
-.BI experimental_verify \fR=\fPbool
-Enable experimental verification. Standard verify records I/O metadata for
-later use during the verification phase. Experimental verify instead resets the
-file after the write phase and then replays I/Os for the verification phase.
.SS "Steady state"
.TP
.BI steadystate \fR=\fPstr:float "\fR,\fP ss" \fR=\fPstr:float
.TP
.BI steadystate_duration \fR=\fPtime "\fR,\fP ss_dur" \fR=\fPtime
A rolling window of this duration will be used to judge whether steady state
-has been reached. Data will be collected once per second. The default is 0
-which disables steady state detection. When the unit is omitted, the
-value is interpreted in seconds.
+has been reached. Data will be collected every \fBss_interval\fR. The default
+is 0 which disables steady state detection. When the unit is omitted, the value
+is interpreted in seconds.
.TP
.BI steadystate_ramp_time \fR=\fPtime "\fR,\fP ss_ramp" \fR=\fPtime
Allow the job to run for the specified duration before beginning data
collection for checking the steady state job termination criterion. The
default is 0. When the unit is omitted, the value is interpreted in seconds.
+.TP
+.BI steadystate_check_interval \fR=\fPtime "\fR,\fP ss_interval" \fR=\fPtime
+The values suring the rolling window will be collected with a period of this
+value. If \fBss_interval\fR is 30s and \fBss_dur\fR is 300s, 10 measurements
+will be taken. Default is 1s but that might not converge, especially for slower
+devices, so set this accordingly. When the unit is omitted, the value is
+interpreted in seconds.
.SS "Measurements and reporting"
.TP
.BI per_job_logs \fR=\fPbool
when fio created the I/O unit to completion of the I/O operation.
.TP
.B bw
-Bandwidth statistics based on samples. Same names as the xlat stats,
-but also includes the number of samples taken (\fIsamples\fR) and an
-approximate percentage of total aggregate bandwidth this thread
-received in its group (\fIper\fR). This last value is only really
-useful if the threads in this group are on the same disk, since they
-are then competing for disk access.
+Bandwidth statistics based on measurements from discrete intervals. Fio
+continuosly monitors bytes transferred and I/O operations completed. By default
+fio calculates bandwidth in each half-second interval (see \fBbwavgtime\fR)
+and reports descriptive statistics for the measurements here. Same names as the
+xlat stats, but also includes the number of samples taken (\fIsamples\fR) and an
+approximate percentage of total aggregate bandwidth this thread received in its
+group (\fIper\fR). This last value is only really useful if the threads in this
+group are on the same disk, since they are then competing for disk access.
.TP
.B iops
-IOPS statistics based on samples. Same names as \fBbw\fR.
+IOPS statistics based on measurements from discrete intervals.
+For details see the description for \fBbw\fR above. See
+\fBiopsavgtime\fR to control the duration of the intervals.
+Same values reported here as for \fBbw\fR except for percentage.
.TP
.B lat (nsec/usec/msec)
The distribution of I/O completion latencies. This is the time from when