.PD
.RE
.P
+`z' suffix specifies that the value is measured in zones.
+Value is recalculated once block device's zone size becomes known.
+.P
If the option accepts an upper and lower range, use a colon ':' or
minus '\-' to separate such values. See \fIirange\fR parameter type.
If the lower value specified happens to be larger than the upper value
block device, the zone capacity is obtained from the device information and this
option is ignored.
.TP
-.BI zoneskip \fR=\fPint
+.BI zoneskip \fR=\fPint[z]
For \fBzonemode\fR=strided, the number of bytes to skip after \fBzonesize\fR
bytes of data have been transferred.
should be associated with them.
.RE
.TP
-.BI offset \fR=\fPint
+.BI offset \fR=\fPint[%|z]
Start I/O at the provided offset in the file, given as either a fixed size in
bytes or a percentage. If a percentage is given, the generated offset will be
aligned to the minimum \fBblocksize\fR or to the value of \fBoffset_align\fR if
is aligned upwards to this value. Defaults to 0 meaning that a percentage
offset is aligned to the minimum block size.
.TP
-.BI offset_increment \fR=\fPint
+.BI offset_increment \fR=\fPint[%|z]
If this is provided, then the real offset becomes `\fBoffset\fR + \fBoffset_increment\fR
* thread_number', where the thread number is a counter that starts at 0 and
is incremented for each sub-job (i.e. when \fBnumjobs\fR option is
simulate a smaller amount of memory. The amount specified is per worker.
.SS "I/O size"
.TP
-.BI size \fR=\fPint
+.BI size \fR=\fPint[%|z]
The total size of file I/O for each thread of this job. Fio will run until
this many bytes has been transferred, unless runtime is limited by other options
(such as \fBruntime\fR, for instance, or increased/decreased by \fBio_size\fR).
Can be combined with \fBoffset\fR to constrain the start and end range
that I/O will be done within.
.TP
-.BI io_size \fR=\fPint "\fR,\fB io_limit" \fR=\fPint
+.BI io_size \fR=\fPint[%|z] "\fR,\fB io_limit" \fR=\fPint[%|z]
Normally fio operates within the region set by \fBsize\fR, which means
that the \fBsize\fR option sets both the region and size of I/O to be
performed. Sometimes that is not what you want. With this option, it is
I/O without transferring buffers between user-space and the kernel,
unless \fBverify\fR is set or \fBcuda_io\fR is \fBposix\fR. \fBiomem\fR must
not be \fBcudamalloc\fR. This ioengine defines engine specific options.
+.TP
+.B dfs
+I/O engine supporting asynchronous read and write operations to the DAOS File
+System (DFS) via libdfs.
.SS "I/O engine specific parameters"
In addition, there are some parameters which are only valid when a specific
\fBioengine\fR is in use. These are used identically to normal parameters,
the use of cudaMemcpy.
.RE
.RE
+.TP
+.BI (dfs)pool
+Specify the UUID of the DAOS pool to connect to.
+.TP
+.BI (dfs)cont
+Specify the UUID of the DAOS DAOS container to open.
+.TP
+.BI (dfs)chunk_size
+Specificy a different chunk size (in bytes) for the dfs file.
+Use DAOS container's chunk size by default.
+.TP
+.BI (dfs)object_class
+Specificy a different object class for the dfs file.
+Use DAOS container's object class by default.
.SS "I/O depth"
.TP
.BI iodepth \fR=\fPint
queue depth that meets \fBlatency_target\fR and exit. If true, fio will continue
running and try to meet \fBlatency_target\fR by adjusting queue depth.
.TP
-.BI max_latency \fR=\fPtime
+.BI max_latency \fR=\fPtime[,time][,time]
If set, fio will exit the job with an ETIMEDOUT error if it exceeds this
maximum latency. When the unit is omitted, the value is interpreted in
-microseconds.
+microseconds. Comma-separated values may be specified for reads, writes,
+and trims as described in \fBblocksize\fR.
.TP
.BI rate_cycle \fR=\fPint
Average bandwidth for \fBrate\fR and \fBrate_min\fR over this number