.. option:: runtime=time
- Tell fio to terminate processing after the specified period of time. It
- can be quite hard to determine for how long a specified job will run, so
- this parameter is handy to cap the total runtime to a given time. When
- the unit is omitted, the value is interpreted in seconds.
+ Limit runtime. The test will run until it completes the configured I/O
+ workload or until it has run for this specified amount of time, whichever
+ occurs first. It can be quite hard to determine for how long a specified
+ job will run, so this parameter is handy to cap the total runtime to a
+ given time. When the unit is omitted, the value is interpreted in
+ seconds.
.. option:: time_based
.. option:: opendir=str
- Recursively open any files below directory `str`.
+ Recursively open any files below directory `str`. This accepts only a
+ single directory and unlike related options, colons appearing in the
+ path must not be escaped.
.. option:: lockfile=str
A number between zero and one that indicates the ratio of written bytes
in the zones with write pointers in the IO range to the size of the IO
range. When current ratio is above this ratio, zones are reset
- periodically as :option:`zone_reset_frequency` specifies.
+ periodically as :option:`zone_reset_frequency` specifies. If there are
+ multiple jobs when using this option, the IO range for all write jobs
+ has to be the same.
.. option:: zone_reset_frequency=float
OpenBSD and ZFS on Solaris don't support direct I/O. On Windows the synchronous
ioengines don't support direct I/O. Default: false.
-.. option:: atomic=bool
-
- If value is true, attempt to use atomic direct I/O. Atomic writes are
- guaranteed to be stable once acknowledged by the operating system. Only
- Linux supports O_ATOMIC right now.
-
.. option:: buffered=bool
If value is true, use buffered I/O. This is the opposite of the
.. option:: randrepeat=bool
- Seed the random number generator used for random I/O patterns in a
- predictable way so the pattern is repeatable across runs. Default: true.
+ Seed all random number generators in a predictable way so the pattern
+ is repeatable across runs. Default: true.
.. option:: allrandrepeat=bool
- Seed all random number generators in a predictable way so results are
- repeatable across runs. Default: false.
+ Alias for :option:`randrepeat`. Default: true.
.. option:: randseed=int
**random**
Advise using **FADV_RANDOM**.
+ **noreuse**
+ Advise using **FADV_NOREUSE**. This may be a no-op on older Linux
+ kernels. Since Linux 6.3, it provides a hint to the LRU algorithm.
+ See the :manpage:`posix_fadvise(2)` man page.
+
.. option:: write_hint=str
Use :manpage:`fcntl(2)` to advise the kernel what life time to expect
before overwriting. The `trimwrite` mode works well for this
constraint.
- **pmemblk**
- Read and write using filesystem DAX to a file on a filesystem
- mounted with DAX on a persistent memory device through the PMDK
- libpmemblk library.
-
**dev-dax**
Read and write using device DAX to a persistent memory device (e.g.,
/dev/dax0.0) through the PMDK libpmem library.
For direct I/O, requests will only succeed if cache invalidation isn't required,
file blocks are fully allocated and the disk request could be issued immediately.
+.. option:: fdp=bool : [io_uring_cmd]
+
+ Enable Flexible Data Placement mode for write commands.
+
+.. option:: fdp_pli=str : [io_uring_cmd]
+
+ Select which Placement ID Index/Indicies this job is allowed to use for
+ writes. By default, the job will cycle through all available Placement
+ IDs, so use this to isolate these identifiers to specific jobs. If you
+ want fio to use placement identifier only at indices 0, 2 and 5 specify
+ ``fdp_pli=0,2,5``.
+
.. option:: cpuload=int : [cpuio]
Attempt to use the specified percentage of CPU cycles. This is a mandatory
performance. The default is to enable it only if
:option:`libblkio_wait_mode=eventfd <libblkio_wait_mode>`.
+.. option:: no_completion_thread : [windowsaio]
+
+ Avoid using a separate thread for completion polling.
+
I/O depth
~~~~~~~~~
fio will ignore the thinktime and continue doing IO at the specified
rate, instead of entering a catch-up mode after thinktime is done.
+.. option:: rate_cycle=int
+
+ Average bandwidth for :option:`rate` and :option:`rate_min` over this number
+ of milliseconds. Defaults to 1000.
+
I/O latency
~~~~~~~~~~~
microseconds. Comma-separated values may be specified for reads, writes,
and trims as described in :option:`blocksize`.
-.. option:: rate_cycle=int
-
- Average bandwidth for :option:`rate` and :option:`rate_min` over this number
- of milliseconds. Defaults to 1000.
-
I/O replay
~~~~~~~~~~
verification pass, according to the settings in the job file used. Default
false.
+.. option:: experimental_verify=bool
+
+ Enable experimental verification. Standard verify records I/O metadata
+ for later use during the verification phase. Experimental verify
+ instead resets the file after the write phase and then replays I/Os for
+ the verification phase.
+
.. option:: trim_percentage=int
Number of verify blocks to discard/trim.
Trim this number of I/O blocks.
-.. option:: experimental_verify=bool
-
- Enable experimental verification. Standard verify records I/O metadata
- for later use during the verification phase. Experimental verify
- instead resets the file after the write phase and then replays I/Os for
- the verification phase.
-
Steady state
~~~~~~~~~~~~
.. option:: steadystate_duration=time, ss_dur=time
- A rolling window of this duration will be used to judge whether steady state
- has been reached. Data will be collected once per second. The default is 0
- which disables steady state detection. When the unit is omitted, the
- value is interpreted in seconds.
+ A rolling window of this duration will be used to judge whether steady
+ state has been reached. Data will be collected every
+ :option:`ss_interval`. The default is 0 which disables steady state
+ detection. When the unit is omitted, the value is interpreted in
+ seconds.
.. option:: steadystate_ramp_time=time, ss_ramp=time
collection for checking the steady state job termination criterion. The
default is 0. When the unit is omitted, the value is interpreted in seconds.
+.. option:: steadystate_check_interval=time, ss_interval=time
+
+ The values during the rolling window will be collected with a period of
+ this value. If :option:`ss_interval` is 30s and :option:`ss_dur` is
+ 300s, 10 measurements will be taken. Default is 1s but that might not
+ converge, especially for slower devices, so set this accordingly. When
+ the unit is omitted, the value is interpreted in seconds.
+
Measurements and reporting
~~~~~~~~~~~~~~~~~~~~~~~~~~
It is the sum of submission and completion latency.
**bw**
- Bandwidth statistics based on samples. Same names as the xlat stats,
- but also includes the number of samples taken (**samples**) and an
- approximate percentage of total aggregate bandwidth this thread
- received in its group (**per**). This last value is only really
- useful if the threads in this group are on the same disk, since they
- are then competing for disk access.
+ Bandwidth statistics based on measurements from discrete
+ intervals. Fio continuously monitors bytes transferred and I/O
+ operations completed. By default fio calculates bandwidth in
+ each half-second interval (see :option:`bwavgtime`) and reports
+ descriptive statistics for the measurements here. Same names as
+ the xlat stats, but also includes the number of samples taken
+ (**samples**) and an approximate percentage of total aggregate
+ bandwidth this thread received in its group (**per**). This
+ last value is only really useful if the threads in this group
+ are on the same disk, since they are then competing for disk
+ access.
**iops**
- IOPS statistics based on samples. Same names as bw.
+ IOPS statistics based on measurements from discrete intervals.
+ For details see the description for bw above. See
+ :option:`iopsavgtime` to control the duration of the intervals.
+ Same values reported here as for bw except for percentage.
**lat (nsec/usec/msec)**
The distribution of I/O completion latencies. This is the time from when
projects / fio.git / blobdiff