block compression attempts, but it will stop naive dedupe of
blocks. Default: true.
+buffer_compress_percentage=int If this is set, then fio will attempt to
+ provide IO buffer content (on WRITEs) that compress to
+ the specified level. Fio does this by providing a mix of
+ random data and zeroes. Note that this is per block size
+ unit, for file/disk wide compression level that matches
+ this setting, you'll also want to set refill_buffers.
+
+buffer_compress_chunk=int See buffer_compress_percentage. This
+ setting allows fio to manage how big the ranges of random
+ data and zeroed data is. Without this set, fio will
+ provide buffer_compress_percentage of blocksize random
+ data, followed by the remaining zeroed. With this set
+ to some chunk size smaller than the block size, fio can
+ alternate random and zeroed data throughout the IO
+ buffer.
+
nrfiles=int Number of files to use for this job. Defaults to 1.
openfiles=int Number of files to keep open at the same time. Defaults to
direct=bool If value is true, use non-buffered io. This is usually
O_DIRECT. Note that ZFS on Solaris doesn't support direct io.
+ On Windows the synchronous ioengines don't support direct io.
buffered=bool If value is true, use buffered io. This is the opposite
of the 'direct' option. Defaults to true.
the given offset will not be touched. This effectively
caps the file size at real_size - offset.
+offset_increment=int If this is provided, then the real offset becomes
+ the offset + offset_increment * thread_number, where the
+ thread number is a counter that starts at 0 and is incremented
+ for each job. This option is useful if there are several jobs
+ which are intended to operate on a file in parallel in disjoint
+ segments, with even spacing between the starting points.
+
fsync=int If writing to a file, issue a sync of the dirty data
for every number of blocks given. For example, if you give
32 as a parameter, fio will sync the file for every 32
fdatasync=int Like fsync= but uses fdatasync() to only sync data and not
metadata blocks.
- In FreeBSD there is no fdatasync(), this falls back to
+ In FreeBSD and Windows there is no fdatasync(), this falls back to
using fsync()
sync_file_range=str:val Use sync_file_range() for every 'val' number of
write_bw_log=str If given, write an IOPS log of the jobs in this job
file. See write_bw_log.
+write_iops_log=str Same as write_bw_log, but writes IOPS. If no filename is
+ given with this option, the default filename of
+ "jobname_type.log" is used. Even if the filename is given,
+ fio will still append the type of log.
+
+log_avg_msec=int By default, fio will log an entry in the iops, latency,
+ or bw log for every IO that completes. When writing to the
+ disk log, that can quickly grow to a very large size. Setting
+ this option makes fio average the each log entry over the
+ specified period of time, reducing the resolution of the log.
+ Defaults to 0.
+
lockmem=int Pin down the specified amount of memory with mlock(2). Can
potentially be used instead of removing memory or booting
with less memory to simulate a smaller amount of memory.
ioscheduler=str Attempt to switch the device hosting the file to the specified
io scheduler before running.
-cpuload=int If the job is a CPU cycle eater, attempt to use the specified
- percentage of CPU cycles.
-
-cpuchunks=int If the job is a CPU cycle eater, split the load into
- cycles of the given time. In microseconds.
-
disk_util=bool Generate disk utilization statistics, if the platform
supports it. Defaults to on.
uses. Fio will manually clear it from the CPU mask of other
jobs.
-continue_on_error=bool Normally fio will exit the job on the first observed
+continue_on_error=str Normally fio will exit the job on the first observed
failure. If this option is set, fio will continue the job when
there is a 'non-fatal error' (EIO or EILSEQ) until the runtime
is exceeded or the I/O size specified is completed. If this
given in the stats is the first error that was hit during the
run.
+ The allowed values are:
+
+ none Exit on any IO or verify errors.
+
+ read Continue on read errors, exit on all others.
+
+ write Continue on write errors, exit on all others.
+
+ io Continue on any IO error, exit on all others.
+
+ verify Continue on verify errors, exit on all others.
+
+ all Continue on all errors.
+
+ 0 Backward-compatible alias for 'none'.
+
+ 1 Backward-compatible alias for 'all'.
+
cgroup=str Add job to this control group. If it doesn't exist, it will
be created. The system must have a mounted cgroup blkio
mount point for this to work. If your system doesn't have it
gid=int Set group ID, see uid.
+flow_id=int The ID of the flow. If not specified, it defaults to being a
+ global flow. See flow.
+
+flow=int Weight in token-based flow control. If this value is used, then
+ there is a 'flow counter' which is used to regulate the
+ proportion of activity between two or more jobs. fio attempts
+ to keep this flow counter near zero. The 'flow' parameter
+ stands for how much should be added or subtracted to the flow
+ counter on each iteration of the main I/O loop. That is, if
+ one job has flow=8 and another job has flow=-1, then there
+ will be a roughly 1:8 ratio in how much one runs vs the other.
+
+flow_watermark=int The maximum value that the absolute value of the flow
+ counter is allowed to reach before the job must wait for a
+ lower value of the counter.
+
+flow_sleep=int The period of time, in microseconds, to wait after the flow
+ watermark has been exceeded before retrying operations
+
In addition, there are some parameters which are only valid when a specific
ioengine is in use. These are used identically to normal parameters, with the
caveat that when used on the command line, they must come after the ioengine
enabled when polling for a minimum of 0 events (eg when
iodepth_batch_complete=0).
+[cpu] cpuload=int Attempt to use the specified percentage of CPU cycles.
+
+[cpu] cpuchunks=int Split the load into cycles of the given time. In
+ microseconds.
+
[netsplice] hostname=str
[net] hostname=str The host name or IP address to use for TCP or UDP based IO.
If the job is a TCP listener or UDP reader, the hostname is not