+.TP
+.BI flow_id \fR=\fPint
+The ID of the flow. If not specified, it defaults to being a global flow. See
+\fBflow\fR.
+.TP
+.BI flow \fR=\fPint
+Weight in token-based flow control. If this value is used, then there is a
+\fBflow counter\fR which is used to regulate the proportion of activity between
+two or more jobs. fio attempts to keep this flow counter near zero. The
+\fBflow\fR parameter stands for how much should be added or subtracted to the
+flow counter on each iteration of the main I/O loop. That is, if one job has
+\fBflow=8\fR and another job has \fBflow=-1\fR, then there will be a roughly
+1:8 ratio in how much one runs vs the other.
+.TP
+.BI flow_watermark \fR=\fPint
+The maximum value that the absolute value of the flow counter is allowed to
+reach before the job must wait for a lower value of the counter.
+.TP
+.BI flow_sleep \fR=\fPint
+The period of time, in microseconds, to wait after the flow watermark has been
+exceeded before retrying operations
+.TP
+.BI clat_percentiles \fR=\fPbool
+Enable the reporting of percentiles of completion latencies.
+.TP
+.BI percentile_list \fR=\fPfloat_list
+Overwrite the default list of percentiles for completion
+latencies. Each number is a floating number in the range (0,100], and
+the maximum length of the list is 20. Use ':' to separate the
+numbers. For example, \-\-percentile_list=99.5:99.9 will cause fio to
+report the values of completion latency below which 99.5% and 99.9% of
+the observed latencies fell, respectively.
+.SS "Ioengine Parameters List"
+Some parameters are only valid when a specific ioengine is in use. These are
+used identically to normal parameters, with the caveat that when used on the
+command line, the must come after the ioengine that defines them is selected.
+.TP
+.BI (libaio)userspace_reap
+Normally, with the libaio engine in use, fio will use
+the io_getevents system call to reap newly returned events.
+With this flag turned on, the AIO ring will be read directly
+from user-space to reap events. The reaping mode is only
+enabled when polling for a minimum of 0 events (eg when
+iodepth_batch_complete=0).
+.TP
+.BI (net,netsplice)hostname \fR=\fPstr
+The host name or IP address to use for TCP or UDP based IO.
+If the job is a TCP listener or UDP reader, the hostname is not
+used and must be omitted.
+.TP
+.BI (net,netsplice)port \fR=\fPint
+The TCP or UDP port to bind to or connect to.
+.TP
+.BI (net,netsplice)nodelay \fR=\fPbool
+Set TCP_NODELAY on TCP connections.
+.TP
+.BI (net,netsplice)protocol \fR=\fPstr "\fR,\fP proto" \fR=\fPstr
+The network protocol to use. Accepted values are:
+.RS
+.RS
+.TP
+.B tcp
+Transmission control protocol
+.TP
+.B udp
+User datagram protocol
+.TP
+.B unix
+UNIX domain socket
+.RE
+.P
+When the protocol is TCP or UDP, the port must also be given,
+as well as the hostname if the job is a TCP listener or UDP
+reader. For unix sockets, the normal filename option should be
+used and the port is invalid.
+.RE
+.TP
+.BI (net,netsplice)listen
+For TCP network connections, tell fio to listen for incoming
+connections rather than initiating an outgoing connection. The
+hostname must be omitted if this option is used.
+.TP
+.BI (net, pingpong) \fR=\fPbool
+Normal a network writer will just continue writing data, and a network reader
+will just consume packages. If pingpong=1 is set, a writer will send its normal
+payload to the reader, then wait for the reader to send the same payload back.
+This allows fio to measure network latencies. The submission and completion
+latencies then measure local time spent sending or receiving, and the
+completion latency measures how long it took for the other end to receive and
+send back.
+.TP
+.BI (e4defrag,donorname) \fR=\fPstr
+File will be used as a block donor (swap extents between files)
+.TP
+.BI (e4defrag,inplace) \fR=\fPint
+Configure donor file block allocation strategy
+.RS
+.BI 0(default) :
+Preallocate donor's file on init
+.TP
+.BI 1:
+allocate space immidietly inside defragment event, and free right after event
+.RE
+.TP