8 5. Detailed list of parameters
13 1.0 Overview and history
14 ------------------------
15 fio was originally written to save me the hassle of writing special test
16 case programs when I wanted to test a specific workload, either for
17 performance reasons or to find/reproduce a bug. The process of writing
18 such a test app can be tiresome, especially if you have to do it often.
19 Hence I needed a tool that would be able to simulate a given io workload
20 without resorting to writing a tailored test case again and again.
22 A test work load is difficult to define, though. There can be any number
23 of processes or threads involved, and they can each be using their own
24 way of generating io. You could have someone dirtying large amounts of
25 memory in an memory mapped file, or maybe several threads issuing
26 reads using asynchronous io. fio needed to be flexible enough to
27 simulate both of these cases, and many more.
31 The first step in getting fio to simulate a desired io workload, is
32 writing a job file describing that specific setup. A job file may contain
33 any number of threads and/or files - the typical contents of the job file
34 is a global section defining shared parameters, and one or more job
35 sections describing the jobs involved. When run, fio parses this file
36 and sets everything up as described. If we break down a job from top to
37 bottom, it contains the following basic parameters:
39 IO type Defines the io pattern issued to the file(s).
40 We may only be reading sequentially from this
41 file(s), or we may be writing randomly. Or even
42 mixing reads and writes, sequentially or randomly.
44 Block size In how large chunks are we issuing io? This may be
45 a single value, or it may describe a range of
48 IO size How much data are we going to be reading/writing.
50 IO engine How do we issue io? We could be memory mapping the
51 file, we could be using regular read/write, we
52 could be using splice, async io, or even
55 IO depth If the io engine is async, how large a queuing
56 depth do we want to maintain?
58 IO type Should we be doing buffered io, or direct/raw io?
60 Num files How many files are we spreading the workload over.
62 Num threads How many threads or processes should we spread
65 The above are the basic parameters defined for a workload, in addition
66 there's a multitude of parameters that modify other aspects of how this
72 See the README file for command line parameters, there are only a few
75 Running fio is normally the easiest part - you just give it the job file
76 (or job files) as parameters:
80 and it will start doing what the job_file tells it to do. You can give
81 more than one job file on the command line, fio will serialize the running
82 of those files. Internally that is the same as using the 'stonewall'
83 parameter described the the parameter section.
85 If the job file contains only one job, you may as well just give the
86 parameters on the command line. The command line parameters are identical
87 to the job parameters, with a few extra that control global parameters
88 (see README). For example, for the job file parameter iodepth=2, the
89 mirror command line option would be --iodepth 2 or --iodepth=2. You can
90 also use the command line for giving more than one job entry. For each
91 --name option that fio sees, it will start a new job with that name.
92 Command line entries following a --name entry will apply to that job,
93 until there are no more entries or a new --name entry is seen. This is
94 similar to the job file options, where each option applies to the current
95 job until a new [] job entry is seen.
97 fio does not need to run as root, except if the files or devices specified
98 in the job section requires that. Some other options may also be restricted,
99 such as memory locking, io scheduler switching, and decreasing the nice value.
104 As previously described, fio accepts one or more job files describing
105 what it is supposed to do. The job file format is the classic ini file,
106 where the names enclosed in [] brackets define the job name. You are free
107 to use any ascii name you want, except 'global' which has special meaning.
108 A global section sets defaults for the jobs described in that file. A job
109 may override a global section parameter, and a job file may even have
110 several global sections if so desired. A job is only affected by a global
111 section residing above it. If the first character in a line is a ';', the
112 entire line is discarded as a comment.
114 So lets look at a really simple job file that define to threads, each
115 randomly reading from a 128MiB file.
117 ; -- start job file --
128 As you can see, the job file sections themselves are empty as all the
129 described parameters are shared. As no filename= option is given, fio
130 makes up a filename for each of the jobs as it sees fit. On the command
131 line, this job would look as follows:
133 $ fio --name=global --rw=randread --size=128m --name=job1 --name=job2
136 Lets look at an example that have a number of processes writing randomly
139 ; -- start job file --
151 Here we have no global section, as we only have one job defined anyway.
152 We want to use async io here, with a depth of 4 for each file. We also
153 increased the buffer size used to 32KiB and define numjobs to 4 to
154 fork 4 identical jobs. The result is 4 processes each randomly writing
155 to their own 64MiB file. Instead of using the above job file, you could
156 have given the parameters on the command line. For this case, you would
159 $ fio --name=random-writers --ioengine=libaio --iodepth=4 --rw=randwrite --bs=32k --direct=0 --size=64m --numjobs=4
161 fio ships with a few example job files, you can also look there for
165 5.0 Detailed list of parameters
166 -------------------------------
168 This section describes in details each parameter associated with a job.
169 Some parameters take an option of a given type, such as an integer or
170 a string. The following types are used:
172 str String. This is a sequence of alpha characters.
173 int Integer. A whole number value, may be negative.
174 siint SI integer. A whole number value, which may contain a postfix
175 describing the base of the number. Accepted postfixes are k/m/g,
176 meaning kilo, mega, and giga. So if you want to specify 4096,
177 you could either write out '4096' or just give 4k. The postfixes
178 signify base 2 values, so 1024 is 1k and 1024k is 1m and so on.
179 bool Boolean. Usually parsed as an integer, however only defined for
180 true and false (1 and 0).
181 irange Integer range with postfix. Allows value range to be given, such
182 as 1024-4096. Also see siint.
184 With the above in mind, here follows the complete list of fio job
187 name=str ASCII name of the job. This may be used to override the
188 name printed by fio for this job. Otherwise the job
189 name is used. On the command line this parameter has the
190 special purpose of also signaling the start of a new
193 directory=str Prefix filenames with this directory. Used to places files
194 in a different location than "./".
196 filename=str Fio normally makes up a filename based on the job name,
197 thread number, and file number. If you want to share
198 files between threads in a job or several jobs, specify
199 a filename for each of them to override the default.
201 rw=str Type of io pattern. Accepted values are:
203 read Sequential reads
204 write Sequential writes
205 randwrite Random writes
206 randread Random reads
207 rw Sequential mixed reads and writes
208 randrw Random mixed reads and writes
210 For the mixed io types, the default is to split them 50/50.
211 For certain types of io the result may still be skewed a bit,
212 since the speed may be different.
214 size=siint The total size of file io for this job. This may describe
215 the size of the single file the job uses, or it may be
216 divided between the number of files in the job. If the
217 file already exists, the file size will be adjusted to this
218 size if larger than the current file size. If this parameter
219 is not given and the file exists, the file size will be used.
221 bs=siint The block size used for the io units. Defaults to 4k. Values
222 can be given for both read and writes. If a single siint is
223 given, it will apply to both. If a second siint is specified
224 after a comma, it will apply to writes only. In other words,
225 the format is either bs=read_and_write or bs=read,write.
226 bs=4k,8k will thus use 4k blocks for reads, and 8k blocks
227 for writes. If you only wish to set the write size, you
228 can do so by passing an empty read size - bs=,8k will set
229 8k for writes and leave the read default value.
231 bsrange=irange Instead of giving a single block size, specify a range
232 and fio will mix the issued io block sizes. The issued
233 io unit will always be a multiple of the minimum value
234 given (also see bs_unaligned). Applies to both reads and
235 writes, however a second range can be given after a comma.
238 bs_unaligned If this option is given, any byte size value within bsrange
239 may be used as a block range. This typically wont work with
240 direct IO, as that normally requires sector alignment.
242 nrfiles=int Number of files to use for this job. Defaults to 1.
244 ioengine=str Defines how the job issues io to the file. The following
247 sync Basic read(2) or write(2) io. lseek(2) is
248 used to position the io location.
250 libaio Linux native asynchronous io.
252 posixaio glibc posix asynchronous io.
254 mmap File is memory mapped and data copied
255 to/from using memcpy(3).
257 splice splice(2) is used to transfer the data and
258 vmsplice(2) to transfer data from user
261 sg SCSI generic sg v3 io. May either be
262 synchronous using the SG_IO ioctl, or if
263 the target is an sg character device
264 we use read(2) and write(2) for asynchronous
267 iodepth=int This defines how many io units to keep in flight against
268 the file. The default is 1 for each file defined in this
269 job, can be overridden with a larger value for higher
272 direct=bool If value is true, use non-buffered io. This is usually
273 O_DIRECT. Defaults to true.
275 offset=siint Start io at the given offset in the file. The data before
276 the given offset will not be touched. This effectively
277 caps the file size at real_size - offset.
279 fsync=int If writing to a file, issue a sync of the dirty data
280 for every number of blocks given. For example, if you give
281 32 as a parameter, fio will sync the file for every 32
282 writes issued. If fio is using non-buffered io, we may
283 not sync the file. The exception is the sg io engine, which
284 synchronizes the disk cache anyway.
286 overwrite=bool If writing to a file, setup the file first and do overwrites.
288 end_fsync=bool If true, fsync file contents when the job exits.
290 rwmixcycle=int Value in milliseconds describing how often to switch between
291 reads and writes for a mixed workload. The default is
294 rwmixread=int How large a percentage of the mix should be reads.
296 rwmixwrite=int How large a percentage of the mix should be writes. If both
297 rwmixread and rwmixwrite is given and the values do not add
298 up to 100%, the latter of the two will be used to override
301 norandommap Normally fio will cover every block of the file when doing
302 random IO. If this option is given, fio will just get a
303 new random offset without looking at past io history. This
304 means that some blocks may not be read or written, and that
305 some blocks may be read/written more than once. This option
306 is mutually exclusive with verify= for that reason.
308 nice=int Run the job with the given nice value. See man nice(2).
310 prio=int Set the io priority value of this job. Linux limits us to
311 a positive value between 0 and 7, with 0 being the highest.
314 prioclass=int Set the io priority class. See man ionice(1).
316 thinktime=int Stall the job x microseconds after an io has completed before
317 issuing the next. May be used to simulate processing being
318 done by an application.
320 rate=int Cap the bandwidth used by this job to this number of KiB/sec.
322 ratemin=int Tell fio to do whatever it can to maintain at least this
325 ratecycle=int Average bandwidth for 'rate' and 'ratemin' over this number
328 cpumask=int Set the CPU affinity of this job. The parameter given is a
329 bitmask of allowed CPU's the job may run on. See man
330 sched_setaffinity(2).
332 startdelay=int Start this job the specified number of seconds after fio
333 has started. Only useful if the job file contains several
334 jobs, and you want to delay starting some jobs to a certain
337 timeout=int Tell fio to terminate processing after the specified number
338 of seconds. It can be quite hard to determine for how long
339 a specified job will run, so this parameter is handy to
340 cap the total runtime to a given time.
342 invalidate=bool Invalidate the buffer/page cache parts for this file prior
343 to starting io. Defaults to true.
345 sync=bool Use sync io for buffered writes. For the majority of the
346 io engines, this means using O_SYNC.
348 mem=str Fio can use various types of memory as the io unit buffer.
349 The allowed values are:
351 malloc Use memory from malloc(3) as the buffers.
353 shm Use shared memory as the buffers. Allocated
356 mmap Use anonymous memory maps as the buffers.
357 Allocated through mmap(2).
359 The area allocated is a function of the maximum allowed
360 bs size for the job, multiplied by the io depth given.
362 exitall When one job finishes, terminate the rest. The default is
363 to wait for each job to finish, sometimes that is not the
366 bwavgtime=int Average the calculated bandwidth over the given time. Value
367 is specified in milliseconds.
369 create_serialize=bool If true, serialize the file creating for the jobs.
370 This may be handy to avoid interleaving of data
371 files, which may greatly depend on the filesystem
372 used and even the number of processors in the system.
374 create_fsync=bool fsync the data file after creation. This is the
377 unlink Unlink the job files when done. fio defaults to doing this,
378 if it created the file itself.
380 loops=int Run the specified number of iterations of this job. Used
381 to repeat the same workload a given number of times. Defaults
384 verify=str If writing to a file, fio can verify the file contents
385 after each iteration of the job. The allowed values are:
387 md5 Use an md5 sum of the data area and store
388 it in the header of each block.
390 crc32 Use a crc32 sum of the data area and store
391 it in the header of each block.
393 This option can be used for repeated burn-in tests of a
394 system to make sure that the written data is also
397 stonewall Wait for preceeding jobs in the job file to exit, before
398 starting this one. Can be used to insert serialization
399 points in the job file.
401 numjobs=int Create the specified number of clones of this job. May be
402 used to setup a larger number of threads/processes doing
405 thread fio defaults to forking jobs, however if this option is
406 given, fio will use pthread_create(3) to create threads
409 zonesize=siint Divide a file into zones of the specified size. See zoneskip.
411 zoneskip=siint Skip the specified number of bytes when zonesize data has
412 been read. The two zone options can be used to only do
413 io on zones of a file.
415 write_iolog=str Write the issued io patterns to the specified file. See
418 read_iolog=str Open an iolog with the specified file name and replay the
419 io patterns it contains. This can be used to store a
420 workload and replay it sometime later.
422 write_bw_log If given, write a bandwidth log of the jobs in this job
423 file. Can be used to store data of the bandwidth of the
424 jobs in their lifetime. The included fio_generate_plots
425 script uses gnuplot to turn these text files into nice
428 write_lat_log Same as write_bw_log, except that this option stores io
429 completion latencies instead.
431 lockmem=siint Pin down the specified amount of memory with mlock(2). Can
432 potentially be used instead of removing memory or booting
433 with less memory to simulate a smaller amount of memory.
435 exec_prerun=str Before running this job, issue the command specified
438 exec_postrun=str After the job completes, issue the command specified
441 ioscheduler=str Attempt to switch the device hosting the file to the specified
442 io scheduler before running.
444 cpuload=int If the job is a CPU cycle eater, attempt to use the specified
445 percentage of CPU cycles.
447 cpuchunks=int If the job is a CPU cycle eater, split the load into
448 cycles of the given time. In milliseconds.
451 6.0 Interpreting the output
452 ---------------------------
454 fio spits out a lot of output. While running, fio will display the
455 status of the jobs created. An example of that would be:
457 Threads running: 1: [_r] [24.79% done] [ 13509/ 8334 kb/s] [eta 00h:01m:31s]
459 The characters inside the square brackets denote the current status of
460 each thread. The possible values (in typical life cycle order) are:
464 P Thread setup, but not started.
466 I Thread initialized, waiting.
467 R Running, doing sequential reads.
468 r Running, doing random reads.
469 W Running, doing sequential writes.
470 w Running, doing random writes.
471 M Running, doing mixed sequential reads/writes.
472 m Running, doing mixed random reads/writes.
473 F Running, currently waiting for fsync()
474 V Running, doing verification of written data.
475 E Thread exited, not reaped by main thread yet.
478 The other values are fairly self explanatory - number of threads
479 currently running and doing io, rate of io since last check, and the estimated
480 completion percentage and time for the running group. It's impossible to
481 estimate runtime of the following groups (if any).
483 When fio is done (or interrupted by ctrl-c), it will show the data for
484 each thread, group of threads, and disks in that order. For each data
485 direction, the output looks like:
487 Client1 (g=0): err= 0:
488 write: io= 32MiB, bw= 666KiB/s, runt= 50320msec
489 slat (msec): min= 0, max= 136, avg= 0.03, dev= 1.92
490 clat (msec): min= 0, max= 631, avg=48.50, dev=86.82
491 bw (KiB/s) : min= 0, max= 1196, per=51.00%, avg=664.02, dev=681.68
492 cpu : usr=1.49%, sys=0.25%, ctx=7969
494 The client number is printed, along with the group id and error of that
495 thread. Below is the io statistics, here for writes. In the order listed,
498 io= Number of megabytes io performed
499 bw= Average bandwidth rate
500 runt= The runtime of that thread
501 slat= Submission latency (avg being the average, dev being the
502 standard deviation). This is the time it took to submit
503 the io. For sync io, the slat is really the completion
504 latency, since queue/complete is one operation there.
505 clat= Completion latency. Same names as slat, this denotes the
506 time from submission to completion of the io pieces. For
507 sync io, clat will usually be equal (or very close) to 0,
508 as the time from submit to complete is basically just
509 CPU time (io has already been done, see slat explanation).
510 bw= Bandwidth. Same names as the xlat stats, but also includes
511 an approximate percentage of total aggregate bandwidth
512 this thread received in this group. This last value is
513 only really useful if the threads in this group are on the
514 same disk, since they are then competing for disk access.
515 cpu= CPU usage. User and system time, along with the number
516 of context switches this thread went through.
518 After each client has been listed, the group statistics are printed. They
521 Run status group 0 (all jobs):
522 READ: io=64MiB, aggrb=22178, minb=11355, maxb=11814, mint=2840msec, maxt=2955msec
523 WRITE: io=64MiB, aggrb=1302, minb=666, maxb=669, mint=50093msec, maxt=50320msec
525 For each data direction, it prints:
527 io= Number of megabytes io performed.
528 aggrb= Aggregate bandwidth of threads in this group.
529 minb= The minimum average bandwidth a thread saw.
530 maxb= The maximum average bandwidth a thread saw.
531 mint= The smallest runtime of the threads in that group.
532 maxt= The longest runtime of the threads in that group.
534 And finally, the disk statistics are printed. They will look like this:
536 Disk stats (read/write):
537 sda: ios=16398/16511, merge=30/162, ticks=6853/819634, in_queue=826487, util=100.00%
539 Each value is printed for both reads and writes, with reads first. The
542 ios= Number of ios performed by all groups.
543 merge= Number of merges io the io scheduler.
544 ticks= Number of ticks we kept the disk busy.
545 io_queue= Total time spent in the disk queue.
546 util= The disk utilization. A value of 100% means we kept the disk
547 busy constantly, 50% would be a disk idling half of the time.
553 For scripted usage where you typically want to generate tables or graphs
554 of the results, fio can output the results in a comma separated format.
555 The format is one long line of values, such as:
557 client1,0,0,936,331,2894,0,0,0.000000,0.000000,1,170,22.115385,34.290410,16,714,84.252874%,366.500000,566.417819,3496,1237,2894,0,0,0.000000,0.000000,0,246,6.671625,21.436952,0,2534,55.465300%,1406.600000,2008.044216,0.000000%,0.431928%,1109
559 Split up, the format is as follows:
561 jobname, groupid, error
563 KiB IO, bandwidth (KiB/sec), runtime (msec)
564 Submission latency: min, max, mean, deviation
565 Completion latency: min, max, mean, deviation
566 Bw: min, max, aggregate percentage of total, mean, deviation
568 KiB IO, bandwidth (KiB/sec), runtime (msec)
569 Submission latency: min, max, mean, deviation
570 Completion latency: min, max, mean, deviation
571 Bw: min, max, aggregate percentage of total, mean, deviation
572 CPU usage: user, system, context switches