--- /dev/null
- mutex_lock(&efx->i2c_adap.bus_lock);
+/****************************************************************************
+ * Driver for Solarflare Solarstorm network controllers and boards
+ * Copyright 2007-2008 Solarflare Communications Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation, incorporated herein by reference.
+ */
+
+#include <linux/rtnetlink.h>
+
+#include "net_driver.h"
+#include "phy.h"
+#include "efx.h"
+#include "falcon.h"
+#include "regs.h"
+#include "io.h"
+#include "workarounds.h"
+
+/* Macros for unpacking the board revision */
+/* The revision info is in host byte order. */
+#define FALCON_BOARD_TYPE(_rev) (_rev >> 8)
+#define FALCON_BOARD_MAJOR(_rev) ((_rev >> 4) & 0xf)
+#define FALCON_BOARD_MINOR(_rev) (_rev & 0xf)
+
+/* Board types */
+#define FALCON_BOARD_SFE4001 0x01
+#define FALCON_BOARD_SFE4002 0x02
+#define FALCON_BOARD_SFN4111T 0x51
+#define FALCON_BOARD_SFN4112F 0x52
+
+/* Blink support. If the PHY has no auto-blink mode so we hang it off a timer */
+#define BLINK_INTERVAL (HZ/2)
+
+static void blink_led_timer(unsigned long context)
+{
+ struct efx_nic *efx = (struct efx_nic *)context;
+ struct efx_board *board = &efx->board_info;
+
+ board->set_id_led(efx, board->blink_state);
+ board->blink_state = !board->blink_state;
+ if (board->blink_resubmit)
+ mod_timer(&board->blink_timer, jiffies + BLINK_INTERVAL);
+}
+
+static void board_blink(struct efx_nic *efx, bool blink)
+{
+ struct efx_board *board = &efx->board_info;
+
+ /* The rtnl mutex serialises all ethtool ioctls, so
+ * nothing special needs doing here. */
+ if (blink) {
+ board->blink_resubmit = true;
+ board->blink_state = false;
+ setup_timer(&board->blink_timer, blink_led_timer,
+ (unsigned long)efx);
+ mod_timer(&board->blink_timer, jiffies + BLINK_INTERVAL);
+ } else {
+ board->blink_resubmit = false;
+ if (board->blink_timer.function)
+ del_timer_sync(&board->blink_timer);
+ board->init_leds(efx);
+ }
+}
+
+/*****************************************************************************
+ * Support for LM87 sensor chip used on several boards
+ */
+#define LM87_REG_ALARMS1 0x41
+#define LM87_REG_ALARMS2 0x42
+#define LM87_IN_LIMITS(nr, _min, _max) \
+ 0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min
+#define LM87_AIN_LIMITS(nr, _min, _max) \
+ 0x3B + (nr), _max, 0x1A + (nr), _min
+#define LM87_TEMP_INT_LIMITS(_min, _max) \
+ 0x39, _max, 0x3A, _min
+#define LM87_TEMP_EXT1_LIMITS(_min, _max) \
+ 0x37, _max, 0x38, _min
+
+#define LM87_ALARM_TEMP_INT 0x10
+#define LM87_ALARM_TEMP_EXT1 0x20
+
+#if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE)
+
+static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
+ const u8 *reg_values)
+{
+ struct i2c_client *client = i2c_new_device(&efx->i2c_adap, info);
+ int rc;
+
+ if (!client)
+ return -EIO;
+
+ while (*reg_values) {
+ u8 reg = *reg_values++;
+ u8 value = *reg_values++;
+ rc = i2c_smbus_write_byte_data(client, reg, value);
+ if (rc)
+ goto err;
+ }
+
+ efx->board_info.hwmon_client = client;
+ return 0;
+
+err:
+ i2c_unregister_device(client);
+ return rc;
+}
+
+static void efx_fini_lm87(struct efx_nic *efx)
+{
+ i2c_unregister_device(efx->board_info.hwmon_client);
+}
+
+static int efx_check_lm87(struct efx_nic *efx, unsigned mask)
+{
+ struct i2c_client *client = efx->board_info.hwmon_client;
+ s32 alarms1, alarms2;
+
+ /* If link is up then do not monitor temperature */
+ if (EFX_WORKAROUND_7884(efx) && efx->link_up)
+ return 0;
+
+ alarms1 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
+ alarms2 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
+ if (alarms1 < 0)
+ return alarms1;
+ if (alarms2 < 0)
+ return alarms2;
+ alarms1 &= mask;
+ alarms2 &= mask >> 8;
+ if (alarms1 || alarms2) {
+ EFX_ERR(efx,
+ "LM87 detected a hardware failure (status %02x:%02x)"
+ "%s%s\n",
+ alarms1, alarms2,
+ (alarms1 & LM87_ALARM_TEMP_INT) ? " INTERNAL" : "",
+ (alarms1 & LM87_ALARM_TEMP_EXT1) ? " EXTERNAL" : "");
+ return -ERANGE;
+ }
+
+ return 0;
+}
+
+#else /* !CONFIG_SENSORS_LM87 */
+
+static inline int
+efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
+ const u8 *reg_values)
+{
+ return 0;
+}
+static inline void efx_fini_lm87(struct efx_nic *efx)
+{
+}
+static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask)
+{
+ return 0;
+}
+
+#endif /* CONFIG_SENSORS_LM87 */
+
+/*****************************************************************************
+ * Support for the SFE4001 and SFN4111T NICs.
+ *
+ * The SFE4001 does not power-up fully at reset due to its high power
+ * consumption. We control its power via a PCA9539 I/O expander.
+ * Both boards have a MAX6647 temperature monitor which we expose to
+ * the lm90 driver.
+ *
+ * This also provides minimal support for reflashing the PHY, which is
+ * initiated by resetting it with the FLASH_CFG_1 pin pulled down.
+ * On SFE4001 rev A2 and later this is connected to the 3V3X output of
+ * the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3.
+ * We represent reflash mode as PHY_MODE_SPECIAL and make it mutually
+ * exclusive with the network device being open.
+ */
+
+/**************************************************************************
+ * Support for I2C IO Expander device on SFE40001
+ */
+#define PCA9539 0x74
+
+#define P0_IN 0x00
+#define P0_OUT 0x02
+#define P0_INVERT 0x04
+#define P0_CONFIG 0x06
+
+#define P0_EN_1V0X_LBN 0
+#define P0_EN_1V0X_WIDTH 1
+#define P0_EN_1V2_LBN 1
+#define P0_EN_1V2_WIDTH 1
+#define P0_EN_2V5_LBN 2
+#define P0_EN_2V5_WIDTH 1
+#define P0_EN_3V3X_LBN 3
+#define P0_EN_3V3X_WIDTH 1
+#define P0_EN_5V_LBN 4
+#define P0_EN_5V_WIDTH 1
+#define P0_SHORTEN_JTAG_LBN 5
+#define P0_SHORTEN_JTAG_WIDTH 1
+#define P0_X_TRST_LBN 6
+#define P0_X_TRST_WIDTH 1
+#define P0_DSP_RESET_LBN 7
+#define P0_DSP_RESET_WIDTH 1
+
+#define P1_IN 0x01
+#define P1_OUT 0x03
+#define P1_INVERT 0x05
+#define P1_CONFIG 0x07
+
+#define P1_AFE_PWD_LBN 0
+#define P1_AFE_PWD_WIDTH 1
+#define P1_DSP_PWD25_LBN 1
+#define P1_DSP_PWD25_WIDTH 1
+#define P1_RESERVED_LBN 2
+#define P1_RESERVED_WIDTH 2
+#define P1_SPARE_LBN 4
+#define P1_SPARE_WIDTH 4
+
+/* Temperature Sensor */
+#define MAX664X_REG_RSL 0x02
+#define MAX664X_REG_WLHO 0x0B
+
+static void sfe4001_poweroff(struct efx_nic *efx)
+{
+ struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
+ struct i2c_client *hwmon_client = efx->board_info.hwmon_client;
+
+ /* Turn off all power rails and disable outputs */
+ i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
+ i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
+ i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);
+
+ /* Clear any over-temperature alert */
+ i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
+}
+
+static int sfe4001_poweron(struct efx_nic *efx)
+{
+ struct i2c_client *hwmon_client = efx->board_info.hwmon_client;
+ struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
+ unsigned int i, j;
+ int rc;
+ u8 out;
+
+ /* Clear any previous over-temperature alert */
+ rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
+ if (rc < 0)
+ return rc;
+
+ /* Enable port 0 and port 1 outputs on IO expander */
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
+ if (rc)
+ return rc;
+ rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
+ 0xff & ~(1 << P1_SPARE_LBN));
+ if (rc)
+ goto fail_on;
+
+ /* If PHY power is on, turn it all off and wait 1 second to
+ * ensure a full reset.
+ */
+ rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT);
+ if (rc < 0)
+ goto fail_on;
+ out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
+ (0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
+ (0 << P0_EN_1V0X_LBN));
+ if (rc != out) {
+ EFX_INFO(efx, "power-cycling PHY\n");
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+ if (rc)
+ goto fail_on;
+ schedule_timeout_uninterruptible(HZ);
+ }
+
+ for (i = 0; i < 20; ++i) {
+ /* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
+ out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
+ (1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
+ (1 << P0_X_TRST_LBN));
+ if (efx->phy_mode & PHY_MODE_SPECIAL)
+ out |= 1 << P0_EN_3V3X_LBN;
+
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+ if (rc)
+ goto fail_on;
+ msleep(10);
+
+ /* Turn on 1V power rail */
+ out &= ~(1 << P0_EN_1V0X_LBN);
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+ if (rc)
+ goto fail_on;
+
+ EFX_INFO(efx, "waiting for DSP boot (attempt %d)...\n", i);
+
+ /* In flash config mode, DSP does not turn on AFE, so
+ * just wait 1 second.
+ */
+ if (efx->phy_mode & PHY_MODE_SPECIAL) {
+ schedule_timeout_uninterruptible(HZ);
+ return 0;
+ }
+
+ for (j = 0; j < 10; ++j) {
+ msleep(100);
+
+ /* Check DSP has asserted AFE power line */
+ rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
+ if (rc < 0)
+ goto fail_on;
+ if (rc & (1 << P1_AFE_PWD_LBN))
+ return 0;
+ }
+ }
+
+ EFX_INFO(efx, "timed out waiting for DSP boot\n");
+ rc = -ETIMEDOUT;
+fail_on:
+ sfe4001_poweroff(efx);
+ return rc;
+}
+
+static int sfn4111t_reset(struct efx_nic *efx)
+{
+ efx_oword_t reg;
+
+ /* GPIO 3 and the GPIO register are shared with I2C, so block that */
- mutex_unlock(&efx->i2c_adap.bus_lock);
++ i2c_lock_adapter(&efx->i2c_adap);
+
+ /* Pull RST_N (GPIO 2) low then let it up again, setting the
+ * FLASH_CFG_1 strap (GPIO 3) appropriately. Only change the
+ * output enables; the output levels should always be 0 (low)
+ * and we rely on external pull-ups. */
+ efx_reado(efx, ®, FR_AB_GPIO_CTL);
+ EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, true);
+ efx_writeo(efx, ®, FR_AB_GPIO_CTL);
+ msleep(1000);
+ EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, false);
+ EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO3_OEN,
+ !!(efx->phy_mode & PHY_MODE_SPECIAL));
+ efx_writeo(efx, ®, FR_AB_GPIO_CTL);
+ msleep(1);
+
++ i2c_unlock_adapter(&efx->i2c_adap);
+
+ ssleep(1);
+ return 0;
+}
+
+static ssize_t show_phy_flash_cfg(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
+ return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL));
+}
+
+static ssize_t set_phy_flash_cfg(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
+ enum efx_phy_mode old_mode, new_mode;
+ int err;
+
+ rtnl_lock();
+ old_mode = efx->phy_mode;
+ if (count == 0 || *buf == '0')
+ new_mode = old_mode & ~PHY_MODE_SPECIAL;
+ else
+ new_mode = PHY_MODE_SPECIAL;
+ if (old_mode == new_mode) {
+ err = 0;
+ } else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) {
+ err = -EBUSY;
+ } else {
+ /* Reset the PHY, reconfigure the MAC and enable/disable
+ * MAC stats accordingly. */
+ efx->phy_mode = new_mode;
+ if (new_mode & PHY_MODE_SPECIAL)
+ efx_stats_disable(efx);
+ if (efx->board_info.type == FALCON_BOARD_SFE4001)
+ err = sfe4001_poweron(efx);
+ else
+ err = sfn4111t_reset(efx);
+ efx_reconfigure_port(efx);
+ if (!(new_mode & PHY_MODE_SPECIAL))
+ efx_stats_enable(efx);
+ }
+ rtnl_unlock();
+
+ return err ? err : count;
+}
+
+static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg);
+
+static void sfe4001_fini(struct efx_nic *efx)
+{
+ EFX_INFO(efx, "%s\n", __func__);
+
+ device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+ sfe4001_poweroff(efx);
+ i2c_unregister_device(efx->board_info.ioexp_client);
+ i2c_unregister_device(efx->board_info.hwmon_client);
+}
+
+static int sfe4001_check_hw(struct efx_nic *efx)
+{
+ s32 status;
+
+ /* If XAUI link is up then do not monitor */
+ if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
+ return 0;
+
+ /* Check the powered status of the PHY. Lack of power implies that
+ * the MAX6647 has shut down power to it, probably due to a temp.
+ * alarm. Reading the power status rather than the MAX6647 status
+ * directly because the later is read-to-clear and would thus
+ * start to power up the PHY again when polled, causing us to blip
+ * the power undesirably.
+ * We know we can read from the IO expander because we did
+ * it during power-on. Assume failure now is bad news. */
+ status = i2c_smbus_read_byte_data(efx->board_info.ioexp_client, P1_IN);
+ if (status >= 0 &&
+ (status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
+ return 0;
+
+ /* Use board power control, not PHY power control */
+ sfe4001_poweroff(efx);
+ efx->phy_mode = PHY_MODE_OFF;
+
+ return (status < 0) ? -EIO : -ERANGE;
+}
+
+static struct i2c_board_info sfe4001_hwmon_info = {
+ I2C_BOARD_INFO("max6647", 0x4e),
+};
+
+/* This board uses an I2C expander to provider power to the PHY, which needs to
+ * be turned on before the PHY can be used.
+ * Context: Process context, rtnl lock held
+ */
+static int sfe4001_init(struct efx_nic *efx)
+{
+ int rc;
+
+#if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE)
+ efx->board_info.hwmon_client =
+ i2c_new_device(&efx->i2c_adap, &sfe4001_hwmon_info);
+#else
+ efx->board_info.hwmon_client =
+ i2c_new_dummy(&efx->i2c_adap, sfe4001_hwmon_info.addr);
+#endif
+ if (!efx->board_info.hwmon_client)
+ return -EIO;
+
+ /* Raise board/PHY high limit from 85 to 90 degrees Celsius */
+ rc = i2c_smbus_write_byte_data(efx->board_info.hwmon_client,
+ MAX664X_REG_WLHO, 90);
+ if (rc)
+ goto fail_hwmon;
+
+ efx->board_info.ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539);
+ if (!efx->board_info.ioexp_client) {
+ rc = -EIO;
+ goto fail_hwmon;
+ }
+
+ /* 10Xpress has fixed-function LED pins, so there is no board-specific
+ * blink code. */
+ efx->board_info.blink = tenxpress_phy_blink;
+
+ efx->board_info.monitor = sfe4001_check_hw;
+ efx->board_info.fini = sfe4001_fini;
+
+ if (efx->phy_mode & PHY_MODE_SPECIAL) {
+ /* PHY won't generate a 156.25 MHz clock and MAC stats fetch
+ * will fail. */
+ efx_stats_disable(efx);
+ }
+ rc = sfe4001_poweron(efx);
+ if (rc)
+ goto fail_ioexp;
+
+ rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+ if (rc)
+ goto fail_on;
+
+ EFX_INFO(efx, "PHY is powered on\n");
+ return 0;
+
+fail_on:
+ sfe4001_poweroff(efx);
+fail_ioexp:
+ i2c_unregister_device(efx->board_info.ioexp_client);
+fail_hwmon:
+ i2c_unregister_device(efx->board_info.hwmon_client);
+ return rc;
+}
+
+static int sfn4111t_check_hw(struct efx_nic *efx)
+{
+ s32 status;
+
+ /* If XAUI link is up then do not monitor */
+ if (EFX_WORKAROUND_7884(efx) && efx->mac_up)
+ return 0;
+
+ /* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */
+ status = i2c_smbus_read_byte_data(efx->board_info.hwmon_client,
+ MAX664X_REG_RSL);
+ if (status < 0)
+ return -EIO;
+ if (status & 0x57)
+ return -ERANGE;
+ return 0;
+}
+
+static void sfn4111t_fini(struct efx_nic *efx)
+{
+ EFX_INFO(efx, "%s\n", __func__);
+
+ device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+ i2c_unregister_device(efx->board_info.hwmon_client);
+}
+
+static struct i2c_board_info sfn4111t_a0_hwmon_info = {
+ I2C_BOARD_INFO("max6647", 0x4e),
+};
+
+static struct i2c_board_info sfn4111t_r5_hwmon_info = {
+ I2C_BOARD_INFO("max6646", 0x4d),
+};
+
+static int sfn4111t_init(struct efx_nic *efx)
+{
+ int i = 0;
+ int rc;
+
+ efx->board_info.hwmon_client =
+ i2c_new_device(&efx->i2c_adap,
+ (efx->board_info.minor < 5) ?
+ &sfn4111t_a0_hwmon_info :
+ &sfn4111t_r5_hwmon_info);
+ if (!efx->board_info.hwmon_client)
+ return -EIO;
+
+ efx->board_info.blink = tenxpress_phy_blink;
+ efx->board_info.monitor = sfn4111t_check_hw;
+ efx->board_info.fini = sfn4111t_fini;
+
+ rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+ if (rc)
+ goto fail_hwmon;
+
+ do {
+ if (efx->phy_mode & PHY_MODE_SPECIAL) {
+ /* PHY may not generate a 156.25 MHz clock and MAC
+ * stats fetch will fail. */
+ efx_stats_disable(efx);
+ sfn4111t_reset(efx);
+ }
+ rc = sft9001_wait_boot(efx);
+ if (rc == 0)
+ return 0;
+ efx->phy_mode = PHY_MODE_SPECIAL;
+ } while (rc == -EINVAL && ++i < 2);
+
+ device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+fail_hwmon:
+ i2c_unregister_device(efx->board_info.hwmon_client);
+ return rc;
+}
+
+/*****************************************************************************
+ * Support for the SFE4002
+ *
+ */
+static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfe4002_lm87_regs[] = {
+ LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */
+ LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */
+ LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */
+ LM87_IN_LIMITS(3, 0xb0, 0xc9), /* 5V: 4.6-5.2V */
+ LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */
+ LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */
+ LM87_AIN_LIMITS(0, 0xa0, 0xb2), /* AIN1: 1.66V +/- 5% */
+ LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */
+ LM87_TEMP_INT_LIMITS(10, 60), /* board */
+ LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */
+ 0
+};
+
+static struct i2c_board_info sfe4002_hwmon_info = {
+ I2C_BOARD_INFO("lm87", 0x2e),
+ .platform_data = &sfe4002_lm87_channel,
+};
+
+/****************************************************************************/
+/* LED allocations. Note that on rev A0 boards the schematic and the reality
+ * differ: red and green are swapped. Below is the fixed (A1) layout (there
+ * are only 3 A0 boards in existence, so no real reason to make this
+ * conditional).
+ */
+#define SFE4002_FAULT_LED (2) /* Red */
+#define SFE4002_RX_LED (0) /* Green */
+#define SFE4002_TX_LED (1) /* Amber */
+
+static void sfe4002_init_leds(struct efx_nic *efx)
+{
+ /* Set the TX and RX LEDs to reflect status and activity, and the
+ * fault LED off */
+ falcon_qt202x_set_led(efx, SFE4002_TX_LED,
+ QUAKE_LED_TXLINK | QUAKE_LED_LINK_ACTSTAT);
+ falcon_qt202x_set_led(efx, SFE4002_RX_LED,
+ QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
+ falcon_qt202x_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
+}
+
+static void sfe4002_set_id_led(struct efx_nic *efx, bool state)
+{
+ falcon_qt202x_set_led(efx, SFE4002_FAULT_LED, state ? QUAKE_LED_ON :
+ QUAKE_LED_OFF);
+}
+
+static int sfe4002_check_hw(struct efx_nic *efx)
+{
+ /* A0 board rev. 4002s report a temperature fault the whole time
+ * (bad sensor) so we mask it out. */
+ unsigned alarm_mask =
+ (efx->board_info.major == 0 && efx->board_info.minor == 0) ?
+ ~LM87_ALARM_TEMP_EXT1 : ~0;
+
+ return efx_check_lm87(efx, alarm_mask);
+}
+
+static int sfe4002_init(struct efx_nic *efx)
+{
+ int rc = efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs);
+ if (rc)
+ return rc;
+ efx->board_info.monitor = sfe4002_check_hw;
+ efx->board_info.init_leds = sfe4002_init_leds;
+ efx->board_info.set_id_led = sfe4002_set_id_led;
+ efx->board_info.blink = board_blink;
+ efx->board_info.fini = efx_fini_lm87;
+ return 0;
+}
+
+/*****************************************************************************
+ * Support for the SFN4112F
+ *
+ */
+static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfn4112f_lm87_regs[] = {
+ LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */
+ LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */
+ LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */
+ LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */
+ LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */
+ LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */
+ LM87_TEMP_INT_LIMITS(10, 60), /* board */
+ LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */
+ 0
+};
+
+static struct i2c_board_info sfn4112f_hwmon_info = {
+ I2C_BOARD_INFO("lm87", 0x2e),
+ .platform_data = &sfn4112f_lm87_channel,
+};
+
+#define SFN4112F_ACT_LED 0
+#define SFN4112F_LINK_LED 1
+
+static void sfn4112f_init_leds(struct efx_nic *efx)
+{
+ falcon_qt202x_set_led(efx, SFN4112F_ACT_LED,
+ QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
+ falcon_qt202x_set_led(efx, SFN4112F_LINK_LED,
+ QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
+}
+
+static void sfn4112f_set_id_led(struct efx_nic *efx, bool state)
+{
+ falcon_qt202x_set_led(efx, SFN4112F_LINK_LED,
+ state ? QUAKE_LED_ON : QUAKE_LED_OFF);
+}
+
+static int sfn4112f_check_hw(struct efx_nic *efx)
+{
+ /* Mask out unused sensors */
+ return efx_check_lm87(efx, ~0x48);
+}
+
+static int sfn4112f_init(struct efx_nic *efx)
+{
+ int rc = efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
+ if (rc)
+ return rc;
+ efx->board_info.monitor = sfn4112f_check_hw;
+ efx->board_info.init_leds = sfn4112f_init_leds;
+ efx->board_info.set_id_led = sfn4112f_set_id_led;
+ efx->board_info.blink = board_blink;
+ efx->board_info.fini = efx_fini_lm87;
+ return 0;
+}
+
+/* This will get expanded as board-specific details get moved out of the
+ * PHY drivers. */
+struct falcon_board_data {
+ u8 type;
+ const char *ref_model;
+ const char *gen_type;
+ int (*init) (struct efx_nic *nic);
+};
+
+
+static struct falcon_board_data board_data[] = {
+ { FALCON_BOARD_SFE4001, "SFE4001", "10GBASE-T adapter", sfe4001_init },
+ { FALCON_BOARD_SFE4002, "SFE4002", "XFP adapter", sfe4002_init },
+ { FALCON_BOARD_SFN4111T, "SFN4111T", "100/1000/10GBASE-T adapter",
+ sfn4111t_init },
+ { FALCON_BOARD_SFN4112F, "SFN4112F", "SFP+ adapter",
+ sfn4112f_init },
+};
+
+void falcon_probe_board(struct efx_nic *efx, u16 revision_info)
+{
+ struct falcon_board_data *data = NULL;
+ int i;
+
+ efx->board_info.type = FALCON_BOARD_TYPE(revision_info);
+ efx->board_info.major = FALCON_BOARD_MAJOR(revision_info);
+ efx->board_info.minor = FALCON_BOARD_MINOR(revision_info);
+
+ for (i = 0; i < ARRAY_SIZE(board_data); i++)
+ if (board_data[i].type == efx->board_info.type)
+ data = &board_data[i];
+
+ if (data) {
+ EFX_INFO(efx, "board is %s rev %c%d\n",
+ (efx->pci_dev->subsystem_vendor == EFX_VENDID_SFC)
+ ? data->ref_model : data->gen_type,
+ 'A' + efx->board_info.major, efx->board_info.minor);
+ efx->board_info.init = data->init;
+ } else {
+ EFX_ERR(efx, "unknown board type %d\n", efx->board_info.type);
+ }
+}
projects / linux-2.6-block.git / commitdiff