drivers/i2c/busses/i2c-designware-core.c

   1 /*
   2  * Synopsys DesignWare I2C adapter driver (master only).
   3  *
   4  * Based on the TI DAVINCI I2C adapter driver.
   5  *
   6  * Copyright (C) 2006 Texas Instruments.
   7  * Copyright (C) 2007 MontaVista Software Inc.
   8  * Copyright (C) 2009 Provigent Ltd.
   9  *
  10  * ----------------------------------------------------------------------------
  11  *
  12  * This program is free software; you can redistribute it and/or modify
  13  * it under the terms of the GNU General Public License as published by
  14  * the Free Software Foundation; either version 2 of the License, or
  15  * (at your option) any later version.
  16  *
  17  * This program is distributed in the hope that it will be useful,
  18  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  19  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  20  * GNU General Public License for more details.
  21  * ----------------------------------------------------------------------------
  22  *
  23  */
  24 #include <linux/export.h>
  25 #include <linux/errno.h>
  26 #include <linux/err.h>
  27 #include <linux/i2c.h>
  28 #include <linux/interrupt.h>
  29 #include <linux/io.h>
  30 #include <linux/pm_runtime.h>
  31 #include <linux/delay.h>
  32 #include <linux/module.h>
  33 #include "i2c-designware-core.h"
  34
  35 /*
  36  * Registers offset
  37  */
  38 #define DW_IC_CON               0x0
  39 #define DW_IC_TAR               0x4
  40 #define DW_IC_DATA_CMD          0x10
  41 #define DW_IC_SS_SCL_HCNT       0x14
  42 #define DW_IC_SS_SCL_LCNT       0x18
  43 #define DW_IC_FS_SCL_HCNT       0x1c
  44 #define DW_IC_FS_SCL_LCNT       0x20
  45 #define DW_IC_HS_SCL_HCNT       0x24
  46 #define DW_IC_HS_SCL_LCNT       0x28
  47 #define DW_IC_INTR_STAT         0x2c
  48 #define DW_IC_INTR_MASK         0x30
  49 #define DW_IC_RAW_INTR_STAT     0x34
  50 #define DW_IC_RX_TL             0x38
  51 #define DW_IC_TX_TL             0x3c
  52 #define DW_IC_CLR_INTR          0x40
  53 #define DW_IC_CLR_RX_UNDER      0x44
  54 #define DW_IC_CLR_RX_OVER       0x48
  55 #define DW_IC_CLR_TX_OVER       0x4c
  56 #define DW_IC_CLR_RD_REQ        0x50
  57 #define DW_IC_CLR_TX_ABRT       0x54
  58 #define DW_IC_CLR_RX_DONE       0x58
  59 #define DW_IC_CLR_ACTIVITY      0x5c
  60 #define DW_IC_CLR_STOP_DET      0x60
  61 #define DW_IC_CLR_START_DET     0x64
  62 #define DW_IC_CLR_GEN_CALL      0x68
  63 #define DW_IC_ENABLE            0x6c
  64 #define DW_IC_STATUS            0x70
  65 #define DW_IC_TXFLR             0x74
  66 #define DW_IC_RXFLR             0x78
  67 #define DW_IC_SDA_HOLD          0x7c
  68 #define DW_IC_TX_ABRT_SOURCE    0x80
  69 #define DW_IC_ENABLE_STATUS     0x9c
  70 #define DW_IC_COMP_PARAM_1      0xf4
  71 #define DW_IC_COMP_VERSION      0xf8
  72 #define DW_IC_SDA_HOLD_MIN_VERS 0x3131312A
  73 #define DW_IC_COMP_TYPE         0xfc
  74 #define DW_IC_COMP_TYPE_VALUE   0x44570140
  75
  76 #define DW_IC_INTR_RX_UNDER     0x001
  77 #define DW_IC_INTR_RX_OVER      0x002
  78 #define DW_IC_INTR_RX_FULL      0x004
  79 #define DW_IC_INTR_TX_OVER      0x008
  80 #define DW_IC_INTR_TX_EMPTY     0x010
  81 #define DW_IC_INTR_RD_REQ       0x020
  82 #define DW_IC_INTR_TX_ABRT      0x040
  83 #define DW_IC_INTR_RX_DONE      0x080
  84 #define DW_IC_INTR_ACTIVITY     0x100
  85 #define DW_IC_INTR_STOP_DET     0x200
  86 #define DW_IC_INTR_START_DET    0x400
  87 #define DW_IC_INTR_GEN_CALL     0x800
  88
  89 #define DW_IC_INTR_DEFAULT_MASK         (DW_IC_INTR_RX_FULL | \
  90                                          DW_IC_INTR_TX_EMPTY | \
  91                                          DW_IC_INTR_TX_ABRT | \
  92                                          DW_IC_INTR_STOP_DET)
  93
  94 #define DW_IC_STATUS_ACTIVITY           0x1
  95 #define DW_IC_STATUS_TFE                BIT(2)
  96 #define DW_IC_STATUS_MST_ACTIVITY       BIT(5)
  97
  98 #define DW_IC_ERR_TX_ABRT       0x1
  99
 100 #define DW_IC_TAR_10BITADDR_MASTER BIT(12)
 101
 102 #define DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH      (BIT(2) | BIT(3))
 103 #define DW_IC_COMP_PARAM_1_SPEED_MODE_MASK      GENMASK(3, 2)
 104
 105 /*
 106  * status codes
 107  */
 108 #define STATUS_IDLE                     0x0
 109 #define STATUS_WRITE_IN_PROGRESS        0x1
 110 #define STATUS_READ_IN_PROGRESS         0x2
 111
 112 #define TIMEOUT                 20 /* ms */
 113
 114 /*
 115  * hardware abort codes from the DW_IC_TX_ABRT_SOURCE register
 116  *
 117  * only expected abort codes are listed here
 118  * refer to the datasheet for the full list
 119  */
 120 #define ABRT_7B_ADDR_NOACK      0
 121 #define ABRT_10ADDR1_NOACK      1
 122 #define ABRT_10ADDR2_NOACK      2
 123 #define ABRT_TXDATA_NOACK       3
 124 #define ABRT_GCALL_NOACK        4
 125 #define ABRT_GCALL_READ         5
 126 #define ABRT_SBYTE_ACKDET       7
 127 #define ABRT_SBYTE_NORSTRT      9
 128 #define ABRT_10B_RD_NORSTRT     10
 129 #define ABRT_MASTER_DIS         11
 130 #define ARB_LOST                12
 131
 132 #define DW_IC_TX_ABRT_7B_ADDR_NOACK     (1UL << ABRT_7B_ADDR_NOACK)
 133 #define DW_IC_TX_ABRT_10ADDR1_NOACK     (1UL << ABRT_10ADDR1_NOACK)
 134 #define DW_IC_TX_ABRT_10ADDR2_NOACK     (1UL << ABRT_10ADDR2_NOACK)
 135 #define DW_IC_TX_ABRT_TXDATA_NOACK      (1UL << ABRT_TXDATA_NOACK)
 136 #define DW_IC_TX_ABRT_GCALL_NOACK       (1UL << ABRT_GCALL_NOACK)
 137 #define DW_IC_TX_ABRT_GCALL_READ        (1UL << ABRT_GCALL_READ)
 138 #define DW_IC_TX_ABRT_SBYTE_ACKDET      (1UL << ABRT_SBYTE_ACKDET)
 139 #define DW_IC_TX_ABRT_SBYTE_NORSTRT     (1UL << ABRT_SBYTE_NORSTRT)
 140 #define DW_IC_TX_ABRT_10B_RD_NORSTRT    (1UL << ABRT_10B_RD_NORSTRT)
 141 #define DW_IC_TX_ABRT_MASTER_DIS        (1UL << ABRT_MASTER_DIS)
 142 #define DW_IC_TX_ARB_LOST               (1UL << ARB_LOST)
 143
 144 #define DW_IC_TX_ABRT_NOACK             (DW_IC_TX_ABRT_7B_ADDR_NOACK | \
 145                                          DW_IC_TX_ABRT_10ADDR1_NOACK | \
 146                                          DW_IC_TX_ABRT_10ADDR2_NOACK | \
 147                                          DW_IC_TX_ABRT_TXDATA_NOACK | \
 148                                          DW_IC_TX_ABRT_GCALL_NOACK)
 149
 150 static char *abort_sources[] = {
 151         [ABRT_7B_ADDR_NOACK] =
 152                 "slave address not acknowledged (7bit mode)",
 153         [ABRT_10ADDR1_NOACK] =
 154                 "first address byte not acknowledged (10bit mode)",
 155         [ABRT_10ADDR2_NOACK] =
 156                 "second address byte not acknowledged (10bit mode)",
 157         [ABRT_TXDATA_NOACK] =
 158                 "data not acknowledged",
 159         [ABRT_GCALL_NOACK] =
 160                 "no acknowledgement for a general call",
 161         [ABRT_GCALL_READ] =
 162                 "read after general call",
 163         [ABRT_SBYTE_ACKDET] =
 164                 "start byte acknowledged",
 165         [ABRT_SBYTE_NORSTRT] =
 166                 "trying to send start byte when restart is disabled",
 167         [ABRT_10B_RD_NORSTRT] =
 168                 "trying to read when restart is disabled (10bit mode)",
 169         [ABRT_MASTER_DIS] =
 170                 "trying to use disabled adapter",
 171         [ARB_LOST] =
 172                 "lost arbitration",
 173 };
 174
 175 static u32 dw_readl(struct dw_i2c_dev *dev, int offset)
 176 {
 177         u32 value;
 178
 179         if (dev->accessor_flags & ACCESS_16BIT)
 180                 value = readw_relaxed(dev->base + offset) |
 181                         (readw_relaxed(dev->base + offset + 2) << 16);
 182         else
 183                 value = readl_relaxed(dev->base + offset);
 184
 185         if (dev->accessor_flags & ACCESS_SWAP)
 186                 return swab32(value);
 187         else
 188                 return value;
 189 }
 190
 191 static void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset)
 192 {
 193         if (dev->accessor_flags & ACCESS_SWAP)
 194                 b = swab32(b);
 195
 196         if (dev->accessor_flags & ACCESS_16BIT) {
 197                 writew_relaxed((u16)b, dev->base + offset);
 198                 writew_relaxed((u16)(b >> 16), dev->base + offset + 2);
 199         } else {
 200                 writel_relaxed(b, dev->base + offset);
 201         }
 202 }
 203
 204 static u32
 205 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset)
 206 {
 207         /*
 208          * DesignWare I2C core doesn't seem to have solid strategy to meet
 209          * the tHD;STA timing spec.  Configuring _HCNT based on tHIGH spec
 210          * will result in violation of the tHD;STA spec.
 211          */
 212         if (cond)
 213                 /*
 214                  * Conditional expression:
 215                  *
 216                  *   IC_[FS]S_SCL_HCNT + (1+4+3) >= IC_CLK * tHIGH
 217                  *
 218                  * This is based on the DW manuals, and represents an ideal
 219                  * configuration.  The resulting I2C bus speed will be
 220                  * faster than any of the others.
 221                  *
 222                  * If your hardware is free from tHD;STA issue, try this one.
 223                  */
 224                 return (ic_clk * tSYMBOL + 500000) / 1000000 - 8 + offset;
 225         else
 226                 /*
 227                  * Conditional expression:
 228                  *
 229                  *   IC_[FS]S_SCL_HCNT + 3 >= IC_CLK * (tHD;STA + tf)
 230                  *
 231                  * This is just experimental rule; the tHD;STA period turned
 232                  * out to be proportinal to (_HCNT + 3).  With this setting,
 233                  * we could meet both tHIGH and tHD;STA timing specs.
 234                  *
 235                  * If unsure, you'd better to take this alternative.
 236                  *
 237                  * The reason why we need to take into account "tf" here,
 238                  * is the same as described in i2c_dw_scl_lcnt().
 239                  */
 240                 return (ic_clk * (tSYMBOL + tf) + 500000) / 1000000
 241                         - 3 + offset;
 242 }
 243
 244 static u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset)
 245 {
 246         /*
 247          * Conditional expression:
 248          *
 249          *   IC_[FS]S_SCL_LCNT + 1 >= IC_CLK * (tLOW + tf)
 250          *
 251          * DW I2C core starts counting the SCL CNTs for the LOW period
 252          * of the SCL clock (tLOW) as soon as it pulls the SCL line.
 253          * In order to meet the tLOW timing spec, we need to take into
 254          * account the fall time of SCL signal (tf).  Default tf value
 255          * should be 0.3 us, for safety.
 256          */
 257         return ((ic_clk * (tLOW + tf) + 500000) / 1000000) - 1 + offset;
 258 }
 259
 260 static void __i2c_dw_enable(struct dw_i2c_dev *dev, bool enable)
 261 {
 262         dw_writel(dev, enable, DW_IC_ENABLE);
 263 }
 264
 265 static void __i2c_dw_enable_and_wait(struct dw_i2c_dev *dev, bool enable)
 266 {
 267         int timeout = 100;
 268
 269         do {
 270                 __i2c_dw_enable(dev, enable);
 271                 if ((dw_readl(dev, DW_IC_ENABLE_STATUS) & 1) == enable)
 272                         return;
 273
 274                 /*
 275                  * Wait 10 times the signaling period of the highest I2C
 276                  * transfer supported by the driver (for 400KHz this is
 277                  * 25us) as described in the DesignWare I2C databook.
 278                  */
 279                 usleep_range(25, 250);
 280         } while (timeout--);
 281
 282         dev_warn(dev->dev, "timeout in %sabling adapter\n",
 283                  enable ? "en" : "dis");
 284 }
 285
 286 static unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev)
 287 {
 288         /*
 289          * Clock is not necessary if we got LCNT/HCNT values directly from
 290          * the platform code.
 291          */
 292         if (WARN_ON_ONCE(!dev->get_clk_rate_khz))
 293                 return 0;
 294         return dev->get_clk_rate_khz(dev);
 295 }
 296
 297 static int i2c_dw_acquire_lock(struct dw_i2c_dev *dev)
 298 {
 299         int ret;
 300
 301         if (!dev->acquire_lock)
 302                 return 0;
 303
 304         ret = dev->acquire_lock(dev);
 305         if (!ret)
 306                 return 0;
 307
 308         dev_err(dev->dev, "couldn't acquire bus ownership\n");
 309
 310         return ret;
 311 }
 312
 313 static void i2c_dw_release_lock(struct dw_i2c_dev *dev)
 314 {
 315         if (dev->release_lock)
 316                 dev->release_lock(dev);
 317 }
 318
 319 /**
 320  * i2c_dw_init() - initialize the designware i2c master hardware
 321  * @dev: device private data
 322  *
 323  * This functions configures and enables the I2C master.
 324  * This function is called during I2C init function, and in case of timeout at
 325  * run time.
 326  */
 327 int i2c_dw_init(struct dw_i2c_dev *dev)
 328 {
 329         u32 hcnt, lcnt;
 330         u32 reg, comp_param1;
 331         u32 sda_falling_time, scl_falling_time;
 332         int ret;
 333
 334         ret = i2c_dw_acquire_lock(dev);
 335         if (ret)
 336                 return ret;
 337
 338         reg = dw_readl(dev, DW_IC_COMP_TYPE);
 339         if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) {
 340                 /* Configure register endianess access */
 341                 dev->accessor_flags |= ACCESS_SWAP;
 342         } else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
 343                 /* Configure register access mode 16bit */
 344                 dev->accessor_flags |= ACCESS_16BIT;
 345         } else if (reg != DW_IC_COMP_TYPE_VALUE) {
 346                 dev_err(dev->dev, "Unknown Synopsys component type: "
 347                         "0x%08x\n", reg);
 348                 i2c_dw_release_lock(dev);
 349                 return -ENODEV;
 350         }
 351
 352         comp_param1 = dw_readl(dev, DW_IC_COMP_PARAM_1);
 353
 354         /* Disable the adapter */
 355         __i2c_dw_enable_and_wait(dev, false);
 356
 357         /* set standard and fast speed deviders for high/low periods */
 358
 359         sda_falling_time = dev->sda_falling_time ?: 300; /* ns */
 360         scl_falling_time = dev->scl_falling_time ?: 300; /* ns */
 361
 362         /* Set SCL timing parameters for standard-mode */
 363         if (dev->ss_hcnt && dev->ss_lcnt) {
 364                 hcnt = dev->ss_hcnt;
 365                 lcnt = dev->ss_lcnt;
 366         } else {
 367                 hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
 368                                         4000,   /* tHD;STA = tHIGH = 4.0 us */
 369                                         sda_falling_time,
 370                                         0,      /* 0: DW default, 1: Ideal */
 371                                         0);     /* No offset */
 372                 lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
 373                                         4700,   /* tLOW = 4.7 us */
 374                                         scl_falling_time,
 375                                         0);     /* No offset */
 376         }
 377         dw_writel(dev, hcnt, DW_IC_SS_SCL_HCNT);
 378         dw_writel(dev, lcnt, DW_IC_SS_SCL_LCNT);
 379         dev_dbg(dev->dev, "Standard-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
 380
 381         /* Set SCL timing parameters for fast-mode or fast-mode plus */
 382         if ((dev->clk_freq == 1000000) && dev->fp_hcnt && dev->fp_lcnt) {
 383                 hcnt = dev->fp_hcnt;
 384                 lcnt = dev->fp_lcnt;
 385         } else if (dev->fs_hcnt && dev->fs_lcnt) {
 386                 hcnt = dev->fs_hcnt;
 387                 lcnt = dev->fs_lcnt;
 388         } else {
 389                 hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
 390                                         600,    /* tHD;STA = tHIGH = 0.6 us */
 391                                         sda_falling_time,
 392                                         0,      /* 0: DW default, 1: Ideal */
 393                                         0);     /* No offset */
 394                 lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
 395                                         1300,   /* tLOW = 1.3 us */
 396                                         scl_falling_time,
 397                                         0);     /* No offset */
 398         }
 399         dw_writel(dev, hcnt, DW_IC_FS_SCL_HCNT);
 400         dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT);
 401         dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
 402
 403         if ((dev->master_cfg & DW_IC_CON_SPEED_MASK) ==
 404                 DW_IC_CON_SPEED_HIGH) {
 405                 if ((comp_param1 & DW_IC_COMP_PARAM_1_SPEED_MODE_MASK)
 406                         != DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH) {
 407                         dev_err(dev->dev, "High Speed not supported!\n");
 408                         dev->master_cfg &= ~DW_IC_CON_SPEED_MASK;
 409                         dev->master_cfg |= DW_IC_CON_SPEED_FAST;
 410                 } else if (dev->hs_hcnt && dev->hs_lcnt) {
 411                         hcnt = dev->hs_hcnt;
 412                         lcnt = dev->hs_lcnt;
 413                         dw_writel(dev, hcnt, DW_IC_HS_SCL_HCNT);
 414                         dw_writel(dev, lcnt, DW_IC_HS_SCL_LCNT);
 415                         dev_dbg(dev->dev, "HighSpeed-mode HCNT:LCNT = %d:%d\n",
 416                                 hcnt, lcnt);
 417                 }
 418         }
 419
 420         /* Configure SDA Hold Time if required */
 421         if (dev->sda_hold_time) {
 422                 reg = dw_readl(dev, DW_IC_COMP_VERSION);
 423                 if (reg >= DW_IC_SDA_HOLD_MIN_VERS)
 424                         dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD);
 425                 else
 426                         dev_warn(dev->dev,
 427                                 "Hardware too old to adjust SDA hold time.");
 428         }
 429
 430         /* Configure Tx/Rx FIFO threshold levels */
 431         dw_writel(dev, dev->tx_fifo_depth / 2, DW_IC_TX_TL);
 432         dw_writel(dev, 0, DW_IC_RX_TL);
 433
 434         /* configure the i2c master */
 435         dw_writel(dev, dev->master_cfg , DW_IC_CON);
 436
 437         i2c_dw_release_lock(dev);
 438
 439         return 0;
 440 }
 441 EXPORT_SYMBOL_GPL(i2c_dw_init);
 442
 443 /*
 444  * Waiting for bus not busy
 445  */
 446 static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev)
 447 {
 448         int timeout = TIMEOUT;
 449
 450         while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) {
 451                 if (timeout <= 0) {
 452                         dev_warn(dev->dev, "timeout waiting for bus ready\n");
 453                         return -ETIMEDOUT;
 454                 }
 455                 timeout--;
 456                 usleep_range(1000, 1100);
 457         }
 458
 459         return 0;
 460 }
 461
 462 static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
 463 {
 464         struct i2c_msg *msgs = dev->msgs;
 465         u32 ic_tar = 0;
 466         bool enabled;
 467
 468         enabled = dw_readl(dev, DW_IC_ENABLE_STATUS) & 1;
 469
 470         if (enabled) {
 471                 u32 ic_status;
 472
 473                 /*
 474                  * Only disable adapter if ic_tar and ic_con can't be
 475                  * dynamically updated
 476                  */
 477                 ic_status = dw_readl(dev, DW_IC_STATUS);
 478                 if (!dev->dynamic_tar_update_enabled ||
 479                     (ic_status & DW_IC_STATUS_MST_ACTIVITY) ||
 480                     !(ic_status & DW_IC_STATUS_TFE)) {
 481                         __i2c_dw_enable_and_wait(dev, false);
 482                         enabled = false;
 483                 }
 484         }
 485
 486         /* if the slave address is ten bit address, enable 10BITADDR */
 487         if (dev->dynamic_tar_update_enabled) {
 488                 /*
 489                  * If I2C_DYNAMIC_TAR_UPDATE is set, the 10-bit addressing
 490                  * mode has to be enabled via bit 12 of IC_TAR register,
 491                  * otherwise bit 4 of IC_CON is used.
 492                  */
 493                 if (msgs[dev->msg_write_idx].flags & I2C_M_TEN)
 494                         ic_tar = DW_IC_TAR_10BITADDR_MASTER;
 495         } else {
 496                 u32 ic_con = dw_readl(dev, DW_IC_CON);
 497
 498                 if (msgs[dev->msg_write_idx].flags & I2C_M_TEN)
 499                         ic_con |= DW_IC_CON_10BITADDR_MASTER;
 500                 else
 501                         ic_con &= ~DW_IC_CON_10BITADDR_MASTER;
 502                 dw_writel(dev, ic_con, DW_IC_CON);
 503         }
 504
 505         /*
 506          * Set the slave (target) address and enable 10-bit addressing mode
 507          * if applicable.
 508          */
 509         dw_writel(dev, msgs[dev->msg_write_idx].addr | ic_tar, DW_IC_TAR);
 510
 511         /* enforce disabled interrupts (due to HW issues) */
 512         i2c_dw_disable_int(dev);
 513
 514         if (!enabled)
 515                 __i2c_dw_enable(dev, true);
 516
 517         /* Clear and enable interrupts */
 518         dw_readl(dev, DW_IC_CLR_INTR);
 519         dw_writel(dev, DW_IC_INTR_DEFAULT_MASK, DW_IC_INTR_MASK);
 520 }
 521
 522 /*
 523  * Initiate (and continue) low level master read/write transaction.
 524  * This function is only called from i2c_dw_isr, and pumping i2c_msg
 525  * messages into the tx buffer.  Even if the size of i2c_msg data is
 526  * longer than the size of the tx buffer, it handles everything.
 527  */
 528 static void
 529 i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
 530 {
 531         struct i2c_msg *msgs = dev->msgs;
 532         u32 intr_mask;
 533         int tx_limit, rx_limit;
 534         u32 addr = msgs[dev->msg_write_idx].addr;
 535         u32 buf_len = dev->tx_buf_len;
 536         u8 *buf = dev->tx_buf;
 537         bool need_restart = false;
 538
 539         intr_mask = DW_IC_INTR_DEFAULT_MASK;
 540
 541         for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) {
 542                 /*
 543                  * if target address has changed, we need to
 544                  * reprogram the target address in the i2c
 545                  * adapter when we are done with this transfer
 546                  */
 547                 if (msgs[dev->msg_write_idx].addr != addr) {
 548                         dev_err(dev->dev,
 549                                 "%s: invalid target address\n", __func__);
 550                         dev->msg_err = -EINVAL;
 551                         break;
 552                 }
 553
 554                 if (msgs[dev->msg_write_idx].len == 0) {
 555                         dev_err(dev->dev,
 556                                 "%s: invalid message length\n", __func__);
 557                         dev->msg_err = -EINVAL;
 558                         break;
 559                 }
 560
 561                 if (!(dev->status & STATUS_WRITE_IN_PROGRESS)) {
 562                         /* new i2c_msg */
 563                         buf = msgs[dev->msg_write_idx].buf;
 564                         buf_len = msgs[dev->msg_write_idx].len;
 565
 566                         /* If both IC_EMPTYFIFO_HOLD_MASTER_EN and
 567                          * IC_RESTART_EN are set, we must manually
 568                          * set restart bit between messages.
 569                          */
 570                         if ((dev->master_cfg & DW_IC_CON_RESTART_EN) &&
 571                                         (dev->msg_write_idx > 0))
 572                                 need_restart = true;
 573                 }
 574
 575                 tx_limit = dev->tx_fifo_depth - dw_readl(dev, DW_IC_TXFLR);
 576                 rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR);
 577
 578                 while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) {
 579                         u32 cmd = 0;
 580
 581                         /*
 582                          * If IC_EMPTYFIFO_HOLD_MASTER_EN is set we must
 583                          * manually set the stop bit. However, it cannot be
 584                          * detected from the registers so we set it always
 585                          * when writing/reading the last byte.
 586                          */
 587                         if (dev->msg_write_idx == dev->msgs_num - 1 &&
 588                             buf_len == 1)
 589                                 cmd |= BIT(9);
 590
 591                         if (need_restart) {
 592                                 cmd |= BIT(10);
 593                                 need_restart = false;
 594                         }
 595
 596                         if (msgs[dev->msg_write_idx].flags & I2C_M_RD) {
 597
 598                                 /* avoid rx buffer overrun */
 599                                 if (rx_limit - dev->rx_outstanding <= 0)
 600                                         break;
 601
 602                                 dw_writel(dev, cmd | 0x100, DW_IC_DATA_CMD);
 603                                 rx_limit--;
 604                                 dev->rx_outstanding++;
 605                         } else
 606                                 dw_writel(dev, cmd | *buf++, DW_IC_DATA_CMD);
 607                         tx_limit--; buf_len--;
 608                 }
 609
 610                 dev->tx_buf = buf;
 611                 dev->tx_buf_len = buf_len;
 612
 613                 if (buf_len > 0) {
 614                         /* more bytes to be written */
 615                         dev->status |= STATUS_WRITE_IN_PROGRESS;
 616                         break;
 617                 } else
 618                         dev->status &= ~STATUS_WRITE_IN_PROGRESS;
 619         }
 620
 621         /*
 622          * If i2c_msg index search is completed, we don't need TX_EMPTY
 623          * interrupt any more.
 624          */
 625         if (dev->msg_write_idx == dev->msgs_num)
 626                 intr_mask &= ~DW_IC_INTR_TX_EMPTY;
 627
 628         if (dev->msg_err)
 629                 intr_mask = 0;
 630
 631         dw_writel(dev, intr_mask,  DW_IC_INTR_MASK);
 632 }
 633
 634 static void
 635 i2c_dw_read(struct dw_i2c_dev *dev)
 636 {
 637         struct i2c_msg *msgs = dev->msgs;
 638         int rx_valid;
 639
 640         for (; dev->msg_read_idx < dev->msgs_num; dev->msg_read_idx++) {
 641                 u32 len;
 642                 u8 *buf;
 643
 644                 if (!(msgs[dev->msg_read_idx].flags & I2C_M_RD))
 645                         continue;
 646
 647                 if (!(dev->status & STATUS_READ_IN_PROGRESS)) {
 648                         len = msgs[dev->msg_read_idx].len;
 649                         buf = msgs[dev->msg_read_idx].buf;
 650                 } else {
 651                         len = dev->rx_buf_len;
 652                         buf = dev->rx_buf;
 653                 }
 654
 655                 rx_valid = dw_readl(dev, DW_IC_RXFLR);
 656
 657                 for (; len > 0 && rx_valid > 0; len--, rx_valid--) {
 658                         *buf++ = dw_readl(dev, DW_IC_DATA_CMD);
 659                         dev->rx_outstanding--;
 660                 }
 661
 662                 if (len > 0) {
 663                         dev->status |= STATUS_READ_IN_PROGRESS;
 664                         dev->rx_buf_len = len;
 665                         dev->rx_buf = buf;
 666                         return;
 667                 } else
 668                         dev->status &= ~STATUS_READ_IN_PROGRESS;
 669         }
 670 }
 671
 672 static int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev)
 673 {
 674         unsigned long abort_source = dev->abort_source;
 675         int i;
 676
 677         if (abort_source & DW_IC_TX_ABRT_NOACK) {
 678                 for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources))
 679                         dev_dbg(dev->dev,
 680                                 "%s: %s\n", __func__, abort_sources[i]);
 681                 return -EREMOTEIO;
 682         }
 683
 684         for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources))
 685                 dev_err(dev->dev, "%s: %s\n", __func__, abort_sources[i]);
 686
 687         if (abort_source & DW_IC_TX_ARB_LOST)
 688                 return -EAGAIN;
 689         else if (abort_source & DW_IC_TX_ABRT_GCALL_READ)
 690                 return -EINVAL; /* wrong msgs[] data */
 691         else
 692                 return -EIO;
 693 }
 694
 695 /*
 696  * Prepare controller for a transaction and start transfer by calling
 697  * i2c_dw_xfer_init()
 698  */
 699 static int
 700 i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
 701 {
 702         struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
 703         int ret;
 704
 705         dev_dbg(dev->dev, "%s: msgs: %d\n", __func__, num);
 706
 707         pm_runtime_get_sync(dev->dev);
 708
 709         reinit_completion(&dev->cmd_complete);
 710         dev->msgs = msgs;
 711         dev->msgs_num = num;
 712         dev->cmd_err = 0;
 713         dev->msg_write_idx = 0;
 714         dev->msg_read_idx = 0;
 715         dev->msg_err = 0;
 716         dev->status = STATUS_IDLE;
 717         dev->abort_source = 0;
 718         dev->rx_outstanding = 0;
 719
 720         ret = i2c_dw_acquire_lock(dev);
 721         if (ret)
 722                 goto done_nolock;
 723
 724         ret = i2c_dw_wait_bus_not_busy(dev);
 725         if (ret < 0)
 726                 goto done;
 727
 728         /* start the transfers */
 729         i2c_dw_xfer_init(dev);
 730
 731         /* wait for tx to complete */
 732         if (!wait_for_completion_timeout(&dev->cmd_complete, adap->timeout)) {
 733                 dev_err(dev->dev, "controller timed out\n");
 734                 /* i2c_dw_init implicitly disables the adapter */
 735                 i2c_dw_init(dev);
 736                 ret = -ETIMEDOUT;
 737                 goto done;
 738         }
 739
 740         if (dev->msg_err) {
 741                 ret = dev->msg_err;
 742                 goto done;
 743         }
 744
 745         /* no error */
 746         if (likely(!dev->cmd_err)) {
 747                 ret = num;
 748                 goto done;
 749         }
 750
 751         /* We have an error */
 752         if (dev->cmd_err == DW_IC_ERR_TX_ABRT) {
 753                 ret = i2c_dw_handle_tx_abort(dev);
 754                 goto done;
 755         }
 756         ret = -EIO;
 757
 758 done:
 759         i2c_dw_release_lock(dev);
 760
 761 done_nolock:
 762         pm_runtime_mark_last_busy(dev->dev);
 763         pm_runtime_put_autosuspend(dev->dev);
 764
 765         return ret;
 766 }
 767
 768 static u32 i2c_dw_func(struct i2c_adapter *adap)
 769 {
 770         struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
 771         return dev->functionality;
 772 }
 773
 774 static struct i2c_algorithm i2c_dw_algo = {
 775         .master_xfer    = i2c_dw_xfer,
 776         .functionality  = i2c_dw_func,
 777 };
 778
 779 static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)
 780 {
 781         u32 stat;
 782
 783         /*
 784          * The IC_INTR_STAT register just indicates "enabled" interrupts.
 785          * Ths unmasked raw version of interrupt status bits are available
 786          * in the IC_RAW_INTR_STAT register.
 787          *
 788          * That is,
 789          *   stat = dw_readl(IC_INTR_STAT);
 790          * equals to,
 791          *   stat = dw_readl(IC_RAW_INTR_STAT) & dw_readl(IC_INTR_MASK);
 792          *
 793          * The raw version might be useful for debugging purposes.
 794          */
 795         stat = dw_readl(dev, DW_IC_INTR_STAT);
 796
 797         /*
 798          * Do not use the IC_CLR_INTR register to clear interrupts, or
 799          * you'll miss some interrupts, triggered during the period from
 800          * dw_readl(IC_INTR_STAT) to dw_readl(IC_CLR_INTR).
 801          *
 802          * Instead, use the separately-prepared IC_CLR_* registers.
 803          */
 804         if (stat & DW_IC_INTR_RX_UNDER)
 805                 dw_readl(dev, DW_IC_CLR_RX_UNDER);
 806         if (stat & DW_IC_INTR_RX_OVER)
 807                 dw_readl(dev, DW_IC_CLR_RX_OVER);
 808         if (stat & DW_IC_INTR_TX_OVER)
 809                 dw_readl(dev, DW_IC_CLR_TX_OVER);
 810         if (stat & DW_IC_INTR_RD_REQ)
 811                 dw_readl(dev, DW_IC_CLR_RD_REQ);
 812         if (stat & DW_IC_INTR_TX_ABRT) {
 813                 /*
 814                  * The IC_TX_ABRT_SOURCE register is cleared whenever
 815                  * the IC_CLR_TX_ABRT is read.  Preserve it beforehand.
 816                  */
 817                 dev->abort_source = dw_readl(dev, DW_IC_TX_ABRT_SOURCE);
 818                 dw_readl(dev, DW_IC_CLR_TX_ABRT);
 819         }
 820         if (stat & DW_IC_INTR_RX_DONE)
 821                 dw_readl(dev, DW_IC_CLR_RX_DONE);
 822         if (stat & DW_IC_INTR_ACTIVITY)
 823                 dw_readl(dev, DW_IC_CLR_ACTIVITY);
 824         if (stat & DW_IC_INTR_STOP_DET)
 825                 dw_readl(dev, DW_IC_CLR_STOP_DET);
 826         if (stat & DW_IC_INTR_START_DET)
 827                 dw_readl(dev, DW_IC_CLR_START_DET);
 828         if (stat & DW_IC_INTR_GEN_CALL)
 829                 dw_readl(dev, DW_IC_CLR_GEN_CALL);
 830
 831         return stat;
 832 }
 833
 834 /*
 835  * Interrupt service routine. This gets called whenever an I2C interrupt
 836  * occurs.
 837  */
 838 static irqreturn_t i2c_dw_isr(int this_irq, void *dev_id)
 839 {
 840         struct dw_i2c_dev *dev = dev_id;
 841         u32 stat, enabled;
 842
 843         enabled = dw_readl(dev, DW_IC_ENABLE);
 844         stat = dw_readl(dev, DW_IC_RAW_INTR_STAT);
 845         dev_dbg(dev->dev, "%s: enabled=%#x stat=%#x\n", __func__, enabled, stat);
 846         if (!enabled || !(stat & ~DW_IC_INTR_ACTIVITY))
 847                 return IRQ_NONE;
 848
 849         stat = i2c_dw_read_clear_intrbits(dev);
 850
 851         if (stat & DW_IC_INTR_TX_ABRT) {
 852                 dev->cmd_err |= DW_IC_ERR_TX_ABRT;
 853                 dev->status = STATUS_IDLE;
 854
 855                 /*
 856                  * Anytime TX_ABRT is set, the contents of the tx/rx
 857                  * buffers are flushed.  Make sure to skip them.
 858                  */
 859                 dw_writel(dev, 0, DW_IC_INTR_MASK);
 860                 goto tx_aborted;
 861         }
 862
 863         if (stat & DW_IC_INTR_RX_FULL)
 864                 i2c_dw_read(dev);
 865
 866         if (stat & DW_IC_INTR_TX_EMPTY)
 867                 i2c_dw_xfer_msg(dev);
 868
 869         /*
 870          * No need to modify or disable the interrupt mask here.
 871          * i2c_dw_xfer_msg() will take care of it according to
 872          * the current transmit status.
 873          */
 874
 875 tx_aborted:
 876         if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET))
 877                         || dev->msg_err) {
 878                 /*
 879                  * We must disable interruts before returning and signaling
 880                  * the end of the current transfer. Otherwise the hardware
 881                  * might continue generating interrupts for non-existent
 882                  * transfers.
 883                  */
 884                 i2c_dw_disable_int(dev);
 885                 dw_readl(dev, DW_IC_CLR_INTR);
 886
 887                 complete(&dev->cmd_complete);
 888         } else if (unlikely(dev->accessor_flags & ACCESS_INTR_MASK)) {
 889                 /* workaround to trigger pending interrupt */
 890                 stat = dw_readl(dev, DW_IC_INTR_MASK);
 891                 i2c_dw_disable_int(dev);
 892                 dw_writel(dev, stat, DW_IC_INTR_MASK);
 893         }
 894
 895         return IRQ_HANDLED;
 896 }
 897
 898 void i2c_dw_disable(struct dw_i2c_dev *dev)
 899 {
 900         /* Disable controller */
 901         __i2c_dw_enable_and_wait(dev, false);
 902
 903         /* Disable all interupts */
 904         dw_writel(dev, 0, DW_IC_INTR_MASK);
 905         dw_readl(dev, DW_IC_CLR_INTR);
 906 }
 907 EXPORT_SYMBOL_GPL(i2c_dw_disable);
 908
 909 void i2c_dw_disable_int(struct dw_i2c_dev *dev)
 910 {
 911         dw_writel(dev, 0, DW_IC_INTR_MASK);
 912 }
 913 EXPORT_SYMBOL_GPL(i2c_dw_disable_int);
 914
 915 u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev)
 916 {
 917         return dw_readl(dev, DW_IC_COMP_PARAM_1);
 918 }
 919 EXPORT_SYMBOL_GPL(i2c_dw_read_comp_param);
 920
 921 int i2c_dw_probe(struct dw_i2c_dev *dev)
 922 {
 923         struct i2c_adapter *adap = &dev->adapter;
 924         int r;
 925         u32 reg;
 926
 927         init_completion(&dev->cmd_complete);
 928
 929         r = i2c_dw_init(dev);
 930         if (r)
 931                 return r;
 932
 933         r = i2c_dw_acquire_lock(dev);
 934         if (r)
 935                 return r;
 936
 937         /*
 938          * Test if dynamic TAR update is enabled in this controller by writing
 939          * to IC_10BITADDR_MASTER field in IC_CON: when it is enabled this
 940          * field is read-only so it should not succeed
 941          */
 942         reg = dw_readl(dev, DW_IC_CON);
 943         dw_writel(dev, reg ^ DW_IC_CON_10BITADDR_MASTER, DW_IC_CON);
 944
 945         if ((dw_readl(dev, DW_IC_CON) & DW_IC_CON_10BITADDR_MASTER) ==
 946             (reg & DW_IC_CON_10BITADDR_MASTER)) {
 947                 dev->dynamic_tar_update_enabled = true;
 948                 dev_dbg(dev->dev, "Dynamic TAR update enabled");
 949         }
 950
 951         i2c_dw_release_lock(dev);
 952
 953         snprintf(adap->name, sizeof(adap->name),
 954                  "Synopsys DesignWare I2C adapter");
 955         adap->retries = 3;
 956         adap->algo = &i2c_dw_algo;
 957         adap->dev.parent = dev->dev;
 958         i2c_set_adapdata(adap, dev);
 959
 960         i2c_dw_disable_int(dev);
 961         r = devm_request_irq(dev->dev, dev->irq, i2c_dw_isr,
 962                              IRQF_SHARED | IRQF_COND_SUSPEND,
 963                              dev_name(dev->dev), dev);
 964         if (r) {
 965                 dev_err(dev->dev, "failure requesting irq %i: %d\n",
 966                         dev->irq, r);
 967                 return r;
 968         }
 969
 970         /*
 971          * Increment PM usage count during adapter registration in order to
 972          * avoid possible spurious runtime suspend when adapter device is
 973          * registered to the device core and immediate resume in case bus has
 974          * registered I2C slaves that do I2C transfers in their probe.
 975          */
 976         pm_runtime_get_noresume(dev->dev);
 977         r = i2c_add_numbered_adapter(adap);
 978         if (r)
 979                 dev_err(dev->dev, "failure adding adapter: %d\n", r);
 980         pm_runtime_put_noidle(dev->dev);
 981
 982         return r;
 983 }
 984 EXPORT_SYMBOL_GPL(i2c_dw_probe);
 985
 986 MODULE_DESCRIPTION("Synopsys DesignWare I2C bus adapter core");
 987 MODULE_LICENSE("GPL");