.BI size \fR=\fPint
Total size of I/O for this job. \fBfio\fR will run until this many bytes have
been transfered, unless limited by other options (\fBruntime\fR, for instance).
-Unless \fBnr_files\fR and \fBfilesize\fR options are given, this amount will be
+Unless \fBnrfiles\fR and \fBfilesize\fR options are given, this amount will be
divided between the available files for the job. If not set, fio will use the
full size of the given files or devices. If the the files do not exist, size
must be given.
Sets size to something really large and waits for ENOSPC (no space left on
device) as the terminating condition. Only makes sense with sequential write.
For a read workload, the mount point will be filled first then IO started on
-the result.
+the result. This option doesn't make sense if operating on a raw device node,
+since the size of that is already known by the file system. Additionally,
+writing beyond end-of-device will not return ENOSPC there.
.TP
.BI filesize \fR=\fPirange
Individual file sizes. May be a range, in which case \fBfio\fR will select sizes
Linux native asynchronous I/O.
.TP
.B posixaio
-glibc POSIX asynchronous I/O using \fIaio_read\fR\|(3) and \fIaio_write\fR\|(3).
+POSIX asynchronous I/O using \fIaio_read\fR\|(3) and \fIaio_write\fR\|(3).
+.TP
+.B solarisaio
+Solaris native asynchronous I/O.
+.TP
+.B windowsaio
+Windows native asynchronous I/O.
.TP
.B mmap
File is memory mapped with \fImmap\fR\|(2) and data copied using
.RE
.TP
.BI iodepth \fR=\fPint
-Number of I/O units to keep in flight against the file. Default: 1.
+Number of I/O units to keep in flight against the file. Note that increasing
+iodepth beyond 1 will not affect synchronous ioengines (except for small
+degress when verify_async is in use). Even async engines my impose OS
+restrictions causing the desired depth not to be achieved. This may happen on
+Linux when using libaio and not setting \fBdirect\fR=1, since buffered IO is
+not async on that OS. Keep an eye on the IO depth distribution in the
+fio output to verify that the achieved depth is as expected. Default: 1.
.TP
.BI iodepth_batch \fR=\fPint
Number of I/Os to submit at once. Default: \fBiodepth\fR.
If true, exit the job on the first observed verification failure. Default:
false.
.TP
+.BI verify_dump \fR=\fPbool
+If set, dump the contents of both the original data block and the data block we
+read off disk to files. This allows later analysis to inspect just what kind of
+data corruption occurred. On by default.
+.TP
.BI verify_async \fR=\fPint
Fio will normally verify IO inline from the submitting thread. This option
takes an integer describing how many async offload threads to create for IO
everything is read back and verified. You may want to verify continually
instead for a variety of reasons. Fio stores the meta data associated with an
IO block in memory, so for large verify workloads, quite a bit of memory would
-be used up holding this meta data. If this option is enabled, fio will verify
-the previously written blocks before continuing to write new ones.
+be used up holding this meta data. If this option is enabled, fio will write
+only N blocks before verifying these blocks.
.TP
.BI verify_backlog_batch \fR=\fPint
Control how many blocks fio will verify if verify_backlog is set. If not set,
will default to the value of \fBverify_backlog\fR (meaning the entire queue is
-read back and verified).
+read back and verified). If \fBverify_backlog_batch\fR is less than
+\fBverify_backlog\fR then not all blocks will be verified, if
+\fBverify_backlog_batch\fR is larger than \fBverify_backlog\fR, some blocks
+will be verified more than once.
.TP
.B stonewall
Wait for preceeding jobs in the job file to exit before starting this one.
read.
.TP
.BI write_iolog \fR=\fPstr
-Write the issued I/O patterns to the specified file.
+Write the issued I/O patterns to the specified file. Specify a separate file
+for each job, otherwise the iologs will be interspersed and the file may be
+corrupt.
.TP
.BI read_iolog \fR=\fPstr
Replay the I/O patterns contained in the specified file generated by
\fBreplay_no_stall\fR causes I/Os to be replayed as fast as possible while
still respecting ordering.
.TP
+.BI replay_redirect \fR=\fPstr
+While replaying I/O patterns using \fBread_iolog\fR the default behavior
+is to replay the IOPS onto the major/minor device that each IOP was recorded
+from. Setting \fBreplay_redirect\fR causes all IOPS to be replayed onto the
+single specified device regardless of the device it was recorded from.
+.TP
.B write_bw_log \fR=\fPstr
If given, write a bandwidth log of the jobs in this job file. Can be used to
store data of the bandwidth of the jobs in their lifetime. The included
.PD
.SH TERSE OUTPUT
If the \fB\-\-minimal\fR option is given, the results will be printed in a
-semicolon-delimited format suitable for scripted use. Note that the first
+semicolon-delimited format suitable for scripted use - a job description
+(if provided) follows on a new line. Note that the first
number in the line is the version number. If the output has to be changed
for some reason, this number will be incremented by 1 to signify that
change. The fields are:
.B <=1, 2, 4, 8, 16, 32, >=64
.RE
.P
-IO latency distribution (ms):
+IO latency distribution:
+.RS
+Microseconds:
+.RS
+.B <=2, 4, 10, 20, 50, 100, 250, 500, 750, 1000
+.RE
+Milliseconds:
+.RS
+.B <=2, 4, 10, 20, 50, 100, 250, 500, 750, 1000, 2000, >=2000
+.RE
+.RE
+.P
+Error Info (dependant on continue_on_error, default off):
.RS
-.B <=2, 4, 10, 20, 50, 100, 250, 500, 750, 1000, >=2000
+.B total # errors, first error code
.RE
.P
-.B text description
+.B text description (if provided in config - appears on newline)
.RE
.SH AUTHORS
.B fio
projects / fio.git / blobdiff