.BI \-\-output \fR=\fPfilename
Write output to \fIfilename\fR.
.TP
+.BI \-\-output-format \fR=\fPformat
+Set the reporting format to \fInormal\fR, \fIterse\fR, or \fIjson\fR.
+.TP
.BI \-\-runtime \fR=\fPruntime
Limit run time to \fIruntime\fR seconds.
.TP
Background a fio server, writing the pid to the given pid file.
.TP
.BI \-\-client \fR=\fPhost
-Instead of running the jobs locally, send and run them on the given host.
+Instead of running the jobs locally, send and run them on the given host or set of hosts. See client/server section.
.TP
.BI \-\-idle\-prof \fR=\fPoption
Report cpu idleness on a system or percpu basis (\fIoption\fP=system,percpu) or run unit work calibration only (\fIoption\fP=calibrate).
.TP
.B randrw
Mixed random reads and writes.
+.TP
+.B trimwrite
+Trim and write mixed workload. Blocks will be trimmed first, then the same
+blocks will be written to.
.RE
.P
For mixed I/O, the default split is 50/50. For certain types of io the result
Use \fBposix_fadvise\fR\|(2) to advise the kernel what I/O patterns
are likely to be issued. Default: true.
.TP
+.BI fadvise_stream \fR=\fPint
+Use \fBposix_fadvise\fR\|(2) to advise the kernel what stream ID the
+writes issued belong to. Only supported on Linux. Note, this option
+may change going forward.
+.TP
.BI size \fR=\fPint
Total size of I/O for this job. \fBfio\fR will run until this many bytes have
-been transferred, unless limited by other options (\fBruntime\fR, for instance).
-Unless \fBnrfiles\fR and \fBfilesize\fR options are given, this amount will be
-divided between the available files for the job. If not set, fio will use the
-full size of the given files or devices. If the files do not exist, size
-must be given. It is also possible to give size as a percentage between 1 and
-100. If size=20% is given, fio will use 20% of the full size of the given
-files or devices.
-.TP
-.BI io_limit \fR=\fPint
+been transferred, unless limited by other options (\fBruntime\fR, for instance,
+or increased/descreased by \fBio_size\fR). Unless \fBnrfiles\fR and
+\fBfilesize\fR options are given, this amount will be divided between the
+available files for the job. If not set, fio will use the full size of the
+given files or devices. If the files do not exist, size must be given. It is
+also possible to give size as a percentage between 1 and 100. If size=20% is
+given, fio will use 20% of the full size of the given files or devices.
+.TP
+.BI io_size \fR=\fPint "\fR,\fB io_limit \fR=\fPint
Normally fio operates within the region set by \fBsize\fR, which means that
the \fBsize\fR option sets both the region and size of IO to be performed.
Sometimes that is not what you want. With this option, it is possible to
define just the amount of IO that fio should do. For instance, if \fBsize\fR
is set to 20G and \fBio_limit\fR is set to 5G, fio will perform IO within
-the first 20G but exit when 5G have been done.
+the first 20G but exit when 5G have been done. The opposite is also
+possible - if \fBsize\fR is set to 20G, and \fBio_size\fR is set to 40G, then
+fio will do 40G of IO within the 0..20G region.
.TP
.BI fill_device \fR=\fPbool "\fR,\fB fill_fs" \fR=\fPbool
Sets size to something really large and waits for ENOSPC (no space left on
.TP
.B zero_buffers
Initialize buffers with all zeros. Default: fill buffers with random data.
-The resulting IO buffers will not be completely zeroed, unless
-\fPscramble_buffers\fR is also turned off.
.TP
.B refill_buffers
If this option is given, fio will refill the IO buffers on every submit. The
example job file to create such files, use rw=write option). Please note, you
might want to set necessary environment variables to work with hdfs/libhdfs
properly.
+.TP
+.B mtd
+Read, write and erase an MTD character device (e.g., /dev/mtd0). Discards are
+treated as erases. Depending on the underlying device type, the I/O may have
+to go in a certain pattern, e.g., on NAND, writing sequentially to erase blocks
+and discarding before overwriting. The writetrim mode works well for this
+constraint.
.RE
.P
.RE
Low watermark indicating when to start filling the queue again. Default:
\fBiodepth\fR.
.TP
+.BI io_submit_mode \fR=\fPstr
+This option controls how fio submits the IO to the IO engine. The default is
+\fBinline\fR, which means that the fio job threads submit and reap IO directly.
+If set to \fBoffload\fR, the job threads will offload IO submission to a
+dedicated pool of IO threads. This requires some coordination and thus has a
+bit of extra overhead, especially for lower queue depth IO where it can
+increase latencies. The benefit is that fio can manage submission rates
+independently of the device completion rates. This avoids skewed latency
+reporting if IO gets back up on the device side (the coordinated omission
+problem).
+.TP
.BI direct \fR=\fPbool
If true, use non-buffered I/O (usually O_DIRECT). Default: false.
.TP
\fB\-\-inflate-log\fR command line parameter. The files will be stored with a
\fB\.fz\fR suffix.
.TP
+.BI block_error_percentiles \fR=\fPbool
+If set, record errors in trim block-sized units from writes and trims and output
+a histogram of how many trims it took to get to errors, and what kind of error
+was encountered.
+.TP
.BI disable_lat \fR=\fPbool
Disable measurements of total latency numbers. Useful only for cutting
back the number of calls to \fBgettimeofday\fR\|(2), as that does impact performance at
Enable the reporting of percentiles of completion latencies.
.TP
.BI percentile_list \fR=\fPfloat_list
-Overwrite the default list of percentiles for completion
-latencies. Each number is a floating number in the range (0,100], and
-the maximum length of the list is 20. Use ':' to separate the
+Overwrite the default list of percentiles for completion latencies and the
+block error histogram. Each number is a floating number in the range (0,100],
+and the maximum length of the list is 20. Use ':' to separate the
numbers. For example, \-\-percentile_list=99.5:99.9 will cause fio to
report the values of completion latency below which 99.5% and 99.9% of
the observed latencies fell, respectively.
.TP
.BI (rbd)clientname \fR=\fPstr
Specifies the username (without the 'client.' prefix) used to access the Ceph cluster.
+.TP
+.BI (mtd)skipbad \fR=\fPbool
+Skip operations against known bad blocks.
.SH OUTPUT
While running, \fBfio\fR will display the status of the created jobs. For
example:
fio \-\-client=server \-\-remote-config /path/to/file.fio
-Then the fio serer will open this local (to the server) job file instead
+Then fio will open this local (to the server) job file instead
of being passed one from the client.
+
+If you have many servers (example: 100 VMs/containers), you can input a pathname
+of a file containing host IPs/names as the parameter value for the \-\-client option.
+For example, here is an example "host.list" file containing 2 hostnames:
+
+host1.your.dns.domain
+.br
+host2.your.dns.domain
+
+The fio command would then be:
+
+fio \-\-client=host.list <job file>
+
+In this mode, you cannot input server-specific parameters or job files, and all
+servers receive the same job file.
+
+In order to enable fio \-\-client runs utilizing a shared filesystem from multiple hosts,
+fio \-\-client now prepends the IP address of the server to the filename. For example,
+if fio is using directory /mnt/nfs/fio and is writing filename fileio.tmp,
+with a \-\-client hostfile
+containing two hostnames h1 and h2 with IP addresses 192.168.10.120 and 192.168.10.121, then
+fio will create two files:
+
+/mnt/nfs/fio/192.168.10.120.fileio.tmp
+.br
+/mnt/nfs/fio/192.168.10.121.fileio.tmp
+
.SH AUTHORS
.B fio
projects / fio.git / blobdiff