Convert \fIjobfile\fR to a set of command\-line options.
.TP
.BI \-\-readonly
-Turn on safety read\-only checks, preventing writes. The \fB\-\-readonly\fR
+Turn on safety read\-only checks, preventing writes and trims. The \fB\-\-readonly\fR
option is an extra safety guard to prevent users from accidentally starting
-a write workload when that is not desired. Fio will only write if
-`rw=write/randwrite/rw/randrw' is given. This extra safety net can be used
-as an extra precaution as \fB\-\-readonly\fR will also enable a write check in
-the I/O engine core to prevent writes due to unknown user space bug(s).
+a write or trim workload when that is not desired. Fio will only modify the
+device under test if `rw=write/randwrite/rw/randrw/trim/randtrim/trimwrite'
+is given. This safety net can be used as an extra precaution.
.TP
.BI \-\-eta \fR=\fPwhen
Specifies when real\-time ETA estimate should be printed. \fIwhen\fR may
-be `always', `never' or `auto'.
+be `always', `never' or `auto'. `auto' is the default, it prints ETA when
+requested if the output is a TTY. `always' disregards the output type, and
+prints ETA when requested. `never' never prints ETA.
+.TP
+.BI \-\-eta\-interval \fR=\fPtime
+By default, fio requests client ETA status roughly every second. With this
+option, the interval is configurable. Fio imposes a minimum allowed time to
+avoid flooding the console, less than 250 msec is not supported.
.TP
.BI \-\-eta\-newline \fR=\fPtime
Force a new line for every \fItime\fR period passed. When the unit is omitted,
Tell fio to terminate processing after the specified period of time. It
can be quite hard to determine for how long a specified job will run, so
this parameter is handy to cap the total runtime to a given time. When
-the unit is omitted, the value is intepreted in seconds.
+the unit is omitted, the value is interpreted in seconds.
.TP
.BI time_based
If set, fio will run for the duration of the \fBruntime\fR specified
Sequential writes.
.TP
.B trim
-Sequential trims (Linux block devices only).
+Sequential trims (Linux block devices and SCSI character devices only).
.TP
.B randread
Random reads.
Random writes.
.TP
.B randtrim
-Random trims (Linux block devices only).
+Random trims (Linux block devices and SCSI character devices only).
.TP
.B rw,readwrite
Sequential mixed reads and writes.
.RE
.TP
.BI fadvise_hint \fR=\fPstr
-Use \fBposix_fadvise\fR\|(2) to advise the kernel what I/O patterns
-are likely to be issued. Accepted values are:
+Use \fBposix_fadvise\fR\|(2) or \fBposix_madvise\fR\|(2) to advise the kernel
+what I/O patterns are likely to be issued. Accepted values are:
.RS
.RS
.TP
.TP
.B zoned
Zoned random distribution
+.B zoned_abs
+Zoned absolute random distribution
.RE
.P
When using a \fBzipf\fR or \fBpareto\fR distribution, an input value is also
random_distribution=zoned:60/10:30/20:8/30:2/40
.RE
.P
-similarly to how \fBbssplit\fR works for setting ranges and percentages
+A \fBzoned_abs\fR distribution works exactly like the\fBzoned\fR, except that
+it takes absolute sizes. For example, let's say you wanted to define access
+according to the following criteria:
+.RS
+.P
+.PD 0
+60% of accesses should be to the first 20G
+.P
+30% of accesses should be to the next 100G
+.P
+10% of accesses should be to the next 500G
+.PD
+.RE
+.P
+we can define an absolute zoning distribution with:
+.RS
+.P
+random_distribution=zoned:60/10:30/20:8/30:2/40
+.RE
+.P
+For both \fBzoned\fR and \fBzoned_abs\fR, fio supports defining up to 256
+separate zones.
+.P
+Similarly to how \fBbssplit\fR works for setting ranges and percentages
of block sizes. Like \fBbssplit\fR, it's possible to specify separate
zones for reads, writes, and trims. If just one set is given, it'll apply to
all of them.
and that some blocks may be read/written more than once. If this option is
used with \fBverify\fR and multiple blocksizes (via \fBbsrange\fR),
only intact blocks are verified, i.e., partially\-overwritten blocks are
-ignored.
+ignored. With an async I/O engine and an I/O depth > 1, it is possible for
+the same block to be overwritten, which can cause verification errors. Either
+do not use norandommap in this case, or also use the lfsr random generator.
.TP
.BI softrandommap \fR=\fPbool
See \fBnorandommap\fR. If fio runs with the random block map enabled and
90% 4k writes and 10% 8k writes, you would specify:
.RS
.P
-bssplit=2k/50:4k/50,4k/90,8k/10
+bssplit=2k/50:4k/50,4k/90:8k/10
.RE
+.P
+Fio supports defining up to 64 different weights for each data direction.
.RE
.TP
.BI blocksize_unaligned "\fR,\fB bs_unaligned"
ioctl, or if the target is an sg character device we use
\fBread\fR\|(2) and \fBwrite\fR\|(2) for asynchronous
I/O. Requires \fBfilename\fR option to specify either block or
-character devices.
+character devices. This engine supports trim operations. The
+sg engine includes engine specific options.
.TP
.B null
Doesn't transfer any data, just pretends to. This is mainly used to
at least one non\-cpuio job.
.TP
.B guasi
-The GUASI I/O engine is the Generic Userspace Asyncronous Syscall
+The GUASI I/O engine is the Generic Userspace Asynchronous Syscall
Interface approach to async I/O. See \fIhttp://www.xmailserver.org/guasi\-lib.html\fR
for more info on GUASI.
.TP
.B rdma
The RDMA I/O engine supports both RDMA memory semantics
(RDMA_WRITE/RDMA_READ) and channel semantics (Send/Recv) for the
-InfiniBand, RoCE and iWARP protocols.
+InfiniBand, RoCE and iWARP protocols. This engine defines engine
+specific options.
.TP
.B falloc
I/O engine that does regular fallocate to simulate data transfer as
I/O engine that does regular EXT4_IOC_MOVE_EXT ioctls to simulate
defragment activity in request to DDIR_WRITE event.
.TP
+.B rados
+I/O engine supporting direct access to Ceph Reliable Autonomic Distributed
+Object Store (RADOS) via librados. This ioengine defines engine specific
+options.
+.TP
.B rbd
I/O engine supporting direct access to Ceph Rados Block Devices
(RBD) via librbd without the need to use the kernel rbd driver. This
.TP
.B pmemblk
Read and write using filesystem DAX to a file on a filesystem
-mounted with DAX on a persistent memory device through the NVML
+mounted with DAX on a persistent memory device through the PMDK
libpmemblk library.
.TP
.B dev\-dax
Read and write using device DAX to a persistent memory device (e.g.,
-/dev/dax0.0) through the NVML libpmem library.
+/dev/dax0.0) through the PMDK libpmem library.
.TP
.B external
Prefix to specify loading an external I/O engine object file. Append
.TP
.B libpmem
Read and write using mmap I/O to a file on a filesystem
-mounted with DAX on a persistent memory device through the NVML
+mounted with DAX on a persistent memory device through the PMDK
libpmem library.
.SS "I/O engine specific parameters"
In addition, there are some parameters which are only valid when a specific
this will be the starting port number since fio will use a range of
ports.
.TP
-.BI (netsplice,net)hostname \fR=\fPstr
-The hostname or IP address to use for TCP or UDP based I/O. If the job is
-a TCP listener or UDP reader, the hostname is not used and must be omitted
-unless it is a valid UDP multicast address.
+.BI (rdma)port
+The port to use for RDMA-CM communication. This should be the same
+value on the client and the server side.
+.TP
+.BI (netsplice,net, rdma)hostname \fR=\fPstr
+The hostname or IP address to use for TCP, UDP or RDMA-CM based I/O.
+If the job is a TCP listener or UDP reader, the hostname is not used
+and must be omitted unless it is a valid UDP multicast address.
.TP
.BI (netsplice,net)interface \fR=\fPstr
The IP address of the network interface used to send or receive UDP
.RE
.RE
.TP
-.BI (rbd)clustername \fR=\fPstr
+.BI (rbd,rados)clustername \fR=\fPstr
Specifies the name of the Ceph cluster.
.TP
.BI (rbd)rbdname \fR=\fPstr
Specifies the name of the RBD.
.TP
-.BI (rbd)pool \fR=\fPstr
-Specifies the name of the Ceph pool containing RBD.
+.BI (rbd,rados)pool \fR=\fPstr
+Specifies the name of the Ceph pool containing RBD or RADOS data.
.TP
-.BI (rbd)clientname \fR=\fPstr
+.BI (rbd,rados)clientname \fR=\fPstr
Specifies the username (without the 'client.' prefix) used to access the
Ceph cluster. If the \fBclustername\fR is specified, the \fBclientname\fR shall be
the full *type.id* string. If no type. prefix is given, fio will add 'client.'
by default.
.TP
+.BI (rbd,rados)busy_poll \fR=\fPbool
+Poll store instead of waiting for completion. Usually this provides better
+throughput at cost of higher(up to 100%) CPU utilization.
+.TP
.BI (mtd)skip_bad \fR=\fPbool
Skip operations against known bad blocks.
.TP
.TP
.BI (libhdfs)chunk_size
The size of the chunk to use for each file.
+.TP
+.BI (rdma)verb \fR=\fPstr
+The RDMA verb to use on this side of the RDMA ioengine
+connection. Valid values are write, read, send and recv. These
+correspond to the equivalent RDMA verbs (e.g. write = rdma_write
+etc.). Note that this only needs to be specified on the client side of
+the connection. See the examples folder.
+.TP
+.BI (rdma)bindname \fR=\fPstr
+The name to use to bind the local RDMA-CM connection to a local RDMA
+device. This could be a hostname or an IPv4 or IPv6 address. On the
+server side this will be passed into the rdma_bind_addr() function and
+on the client site it will be used in the rdma_resolve_add()
+function. This can be useful when multiple paths exist between the
+client and the server or in certain loopback configurations.
+.TP
+.BI (sg)readfua \fR=\fPbool
+With readfua option set to 1, read operations include the force
+unit access (fua) flag. Default: 0.
+.TP
+.BI (sg)writefua \fR=\fPbool
+With writefua option set to 1, write operations include the force
+unit access (fua) flag. Default: 0.
+.TP
+.BI (sg)sg_write_mode \fR=\fPstr
+Specify the type of write commands to issue. This option can take three
+values:
+.RS
+.RS
+.TP
+.B write (default)
+Write opcodes are issued as usual
+.TP
+.B verify
+Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 0. This
+directs the device to carry out a medium verification with no data
+comparison. The writefua option is ignored with this selection.
+.TP
+.B same
+Issue WRITE SAME commands. This transfers a single block to the device
+and writes this same block of data to a contiguous sequence of LBAs
+beginning at the specified offset. fio's block size parameter
+specifies the amount of data written with each command. However, the
+amount of data actually transferred to the device is equal to the
+device's block (sector) size. For a device with 512 byte sectors,
+blocksize=8k will write 16 sectors with each command. fio will still
+generate 8k of data for each command butonly the first 512 bytes will
+be used and transferred to the device. The writefua option is ignored
+with this selection.
+
.SS "I/O depth"
.TP
.BI iodepth \fR=\fPint
flow, known as the Poisson process
(\fIhttps://en.wikipedia.org/wiki/Poisson_point_process\fR). The lambda will be
10^6 / IOPS for the given workload.
+.TP
+.BI rate_ignore_thinktime \fR=\fPbool
+By default, fio will attempt to catch up to the specified rate setting, if any
+kind of thinktime setting was used. If this option is set, then fio will
+ignore the thinktime and continue doing IO at the specified rate, instead of
+entering a catch-up mode after thinktime is done.
.SS "I/O latency"
.TP
.BI latency_target \fR=\fPtime
replay, the file needs to be turned into a blkparse binary data file first
(`blkparse <device> \-o /dev/null \-d file_for_fio.bin').
.TP
+.BI read_iolog_chunked \fR=\fPbool
+Determines how iolog is read. If false (default) entire \fBread_iolog\fR will
+be read at once. If selected true, input from iolog will be read gradually.
+Useful when iolog is very large, or it is generated.
+.TP
.BI replay_no_stall \fR=\fPbool
When replaying I/O with \fBread_iolog\fR the default behavior is to
attempt to respect the timestamps within the log and replay them with the
still respecting ordering. The result is the same I/O pattern to a given
device, but different timings.
.TP
+.BI replay_time_scale \fR=\fPint
+When replaying I/O with \fBread_iolog\fR, fio will honor the original timing
+in the trace. With this option, it's possible to scale the time. It's a
+percentage option, if set to 50 it means run at 50% the original IO rate in
+the trace. If set to 200, run at twice the original IO rate. Defaults to 100.
+.TP
.BI replay_redirect \fR=\fPstr
While replaying I/O patterns using \fBread_iolog\fR the default behavior
is to replay the IOPS onto the major/minor device that each IOP was recorded
Scale sector offsets down by this factor when replaying traces.
.SS "Threads, processes and job synchronization"
.TP
+.BI replay_skip \fR=\fPstr
+Sometimes it's useful to skip certain IO types in a replay trace. This could
+be, for instance, eliminating the writes in the trace. Or not replaying the
+trims/discards, if you are redirecting to a device that doesn't support them.
+This option takes a comma separated list of read, write, trim, sync.
+.TP
.BI thread
Fio defaults to creating jobs by using fork, however if this option is
given, fio will create jobs by using POSIX Threads' function
.BI prioclass \fR=\fPint
Set the I/O priority class. See man \fBionice\fR\|(1).
.TP
-.BI cpumask \fR=\fPint
-Set the CPU affinity of this job. The parameter given is a bit mask of
-allowed CPUs the job may run on. So if you want the allowed CPUs to be 1
-and 5, you would pass the decimal value of (1 << 1 | 1 << 5), or 34. See man
-\fBsched_setaffinity\fR\|(2). This may not work on all supported
-operating systems or kernel versions. This option doesn't work well for a
-higher CPU count than what you can store in an integer mask, so it can only
-control cpus 1\-32. For boxes with larger CPU counts, use
-\fBcpus_allowed\fR.
-.TP
.BI cpus_allowed \fR=\fPstr
Controls the same options as \fBcpumask\fR, but accepts a textual
-specification of the permitted CPUs instead. So to use CPUs 1 and 5 you
-would specify `cpus_allowed=1,5'. This option also allows a range of CPUs
-to be specified \-\- say you wanted a binding to CPUs 1, 5, and 8 to 15, you
-would set `cpus_allowed=1,5,8\-15'.
+specification of the permitted CPUs instead and CPUs are indexed from 0. So
+to use CPUs 0 and 5 you would specify `cpus_allowed=0,5'. This option also
+allows a range of CPUs to be specified \-\- say you wanted a binding to CPUs
+0, 5, and 8 to 15, you would set `cpus_allowed=0,5,8\-15'.
+.RS
+.P
+On Windows, when `cpus_allowed' is unset only CPUs from fio's current
+processor group will be used and affinity settings are inherited from the
+system. An fio build configured to target Windows 7 makes options that set
+CPUs processor group aware and values will set both the processor group
+and a CPU from within that group. For example, on a system where processor
+group 0 has 40 CPUs and processor group 1 has 32 CPUs, `cpus_allowed'
+values between 0 and 39 will bind CPUs from processor group 0 and
+`cpus_allowed' values between 40 and 71 will bind CPUs from processor
+group 1. When using `cpus_allowed_policy=shared' all CPUs specified by a
+single `cpus_allowed' option must be from the same processor group. For
+Windows fio builds not built for Windows 7, CPUs will only be selected from
+(and be relative to) whatever processor group fio happens to be running in
+and CPUs from other processor groups cannot be used.
+.RE
.TP
.BI cpus_allowed_policy \fR=\fPstr
Set the policy of how fio distributes the CPUs specified by
in the set.
.RE
.TP
+.BI cpumask \fR=\fPint
+Set the CPU affinity of this job. The parameter given is a bit mask of
+allowed CPUs the job may run on. So if you want the allowed CPUs to be 1
+and 5, you would pass the decimal value of (1 << 1 | 1 << 5), or 34. See man
+\fBsched_setaffinity\fR\|(2). This may not work on all supported
+operating systems or kernel versions. This option doesn't work well for a
+higher CPU count than what you can store in an integer mask, so it can only
+control cpus 1\-32. For boxes with larger CPU counts, use
+\fBcpus_allowed\fR.
+.TP
.BI numa_cpu_nodes \fR=\fPstr
Set this job running on specified NUMA nodes' CPUs. The arguments allow
comma delimited list of cpu numbers, A\-B ranges, or `all'. Note, to enable
<mode>[:<nodelist>]
.RE
.P
-`mode' is one of the following memory poicies: `default', `prefer',
+`mode' is one of the following memory policies: `default', `prefer',
`bind', `interleave' or `local'. For `default' and `local' memory
policies, no node needs to be specified. For `prefer', only one node is
allowed. For `bind' and `interleave' the `nodelist' may be as
each block. This will automatically use hardware acceleration
(e.g. SSE4.2 on an x86 or CRC crypto extensions on ARM64) but will
fall back to software crc32c if none is found. Generally the
-fatest checksum fio supports when hardware accelerated.
+fastest checksum fio supports when hardware accelerated.
.TP
.B crc32c\-intel
Synonym for crc32c.
given is a read or random read, fio will assume that it should verify a
previously written file. If the data direction includes any form of write,
the verify will be of the newly written data.
+.P
+To avoid false verification errors, do not use the norandommap option when
+verifying data with async I/O engines and I/O depths > 1. Or use the
+norandommap and the lfsr random generator together to avoid writing to the
+same offset with muliple outstanding I/Os.
.RE
.TP
-.BI verifysort \fR=\fPbool
-If true, fio will sort written verify blocks when it deems it faster to read
-them back in a sorted manner. This is often the case when overwriting an
-existing file, since the blocks are already laid out in the file system. You
-can ignore this option unless doing huge amounts of really fast I/O where
-the red\-black tree sorting CPU time becomes significant. Default: true.
-.TP
-.BI verifysort_nr \fR=\fPint
-Pre\-load and sort verify blocks for a read workload.
-.TP
.BI verify_offset \fR=\fPint
Swap the verification header with data somewhere else in the block before
writing. It is swapped back before verifying.
.BI log_compression_cpus \fR=\fPstr
Define the set of CPUs that are allowed to handle online log compression for
the I/O jobs. This can provide better isolation between performance
-sensitive jobs, and background compression work.
+sensitive jobs, and background compression work. See \fBcpus_allowed\fR for
+the format used.
.TP
.BI log_store_compressed \fR=\fPbool
If set, fio will store the log files in a compressed format. They can be
fell, respectively.
.TP
.BI significant_figures \fR=\fPint
-If using \fB\-\-output\-format\fR of `normal', set the significant figures
-to this value. Higher values will yield more precise IOPS and throughput
-units, while lower values will round. Requires a minimum value of 1 and a
+If using \fB\-\-output\-format\fR of `normal', set the significant figures
+to this value. Higher values will yield more precise IOPS and throughput
+units, while lower values will round. Requires a minimum value of 1 and a
maximum value of 10. Defaults to 4.
.SS "Error handling"
.TP
.RE
.SH AUTHORS
.B fio
-was written by Jens Axboe <jens.axboe@oracle.com>,
-now Jens Axboe <axboe@fb.com>.
+was written by Jens Axboe <axboe@kernel.dk>.
.br
This man page was written by Aaron Carroll <aaronc@cse.unsw.edu.au> based
on documentation by Jens Axboe.
projects / fio.git / blobdiff