.TP
.BI size \fR=\fPint
Total size of I/O for this job. \fBfio\fR will run until this many bytes have
-been transfered, unless limited by other options (\fBruntime\fR, for instance).
+been transferred, unless limited by other options (\fBruntime\fR, for instance).
Unless \fBnrfiles\fR and \fBfilesize\fR options are given, this amount will be
divided between the available files for the job. If not set, fio will use the
full size of the given files or devices. If the the files do not exist, size
same size.
.TP
.BI blocksize \fR=\fPint[,int] "\fR,\fB bs" \fR=\fPint[,int]
-Block size for I/O units. Default: 4k. Values for reads and writes can be
-specified separately in the format \fIread\fR,\fIwrite\fR, either of
-which may be empty to leave that value at its default.
+Block size for I/O units. Default: 4k. Values for reads, writes, and trims
+can be specified separately in the format \fIread\fR,\fIwrite\fR,\fItrim\fR
+either of which may be empty to leave that value at its default. If a trailing
+comma isn't given, the remainder will inherit the last value set.
.TP
.BI blocksize_range \fR=\fPirange[,irange] "\fR,\fB bsrange" \fR=\fPirange[,irange]
Specify a range of I/O block sizes. The issued I/O unit will always be a
multiple of the minimum size, unless \fBblocksize_unaligned\fR is set. Applies
to both reads and writes if only one range is given, but can be specified
-separately with a comma seperating the values. Example: bsrange=1k-4k,2k-8k.
+separately with a comma separating the values. Example: bsrange=1k-4k,2k-8k.
Also (see \fBblocksize\fR).
.TP
.BI bssplit \fR=\fPstr
This option is mutually exclusive with using a random map for files, so it
will turn off that option.
.TP
+.BI bs_is_seq_rand \fR=\fPbool
+If this option is set, fio will use the normal read,write blocksize settings as
+sequential,random instead. Any random read or write will use the WRITE
+blocksize settings, and any sequential read or write will use the READ
+blocksize setting.
+.TP
.B zero_buffers
Initialise buffers with all zeros. Default: fill buffers with random data.
.TP
there are several jobs which are intended to operate on a file in parallel in
disjoint segments, with even spacing between the starting points.
.TP
+.BI number_ios \fR=\fPint
+Fio will normally perform IOs until it has exhausted the size of the region
+set by \fBsize\fR, or if it exhaust the allocated time (or hits an error
+condition). With this setting, the range/size can be set independently of
+the number of IOs to perform. When fio reaches this number, it will exit
+normally and report status.
+.TP
.BI fsync \fR=\fPint
How many I/Os to perform before issuing an \fBfsync\fR\|(2) of dirty data. If
0, don't sync. Default: 0.
For a random workload, set how big a percentage should be random. This defaults
to 100%, in which case the workload is fully random. It can be set from
anywhere from 0 to 100. Setting it to 0 would make the workload fully
-sequential.
-.TP
-.BI percentage_sequential \fR=\fPint
-See \fBpercentage_random\fR.
+sequential. It is possible to set different values for reads, writes, and
+trim. To do so, simply use a comma separated list. See \fBblocksize\fR.
.TP
.B norandommap
Normally \fBfio\fR will cover every block of the file when doing random I/O. If
.BI rate_iops \fR=\fPint
Cap the bandwidth to this number of IOPS. Basically the same as rate, just
specified independently of bandwidth. The same format as \fBrate\fR is used for
-read vs write seperation. If \fBblocksize\fR is a range, the smallest block
+read vs write separation. If \fBblocksize\fR is a range, the smallest block
size is used as the metric.
.TP
.BI rate_iops_min \fR=\fPint
If this rate of I/O is not met, the job will exit. The same format as \fBrate\fR
-is used for read vs write seperation.
+is used for read vs write separation.
.TP
.BI ratecycle \fR=\fPint
Average bandwidth for \fBrate\fR and \fBratemin\fR over this number of
.BI (net,netsplice)port \fR=\fPint
The TCP or UDP port to bind to or connect to.
.TP
+.BI (net,netsplice)interface \fR=\fPstr
+The IP address of the network interface used to send or receive UDP multicast
+packets.
+.TP
+.BI (net,netsplice)ttl \fR=\fPint
+Time-to-live value for outgoing UDP multicast packets. Default: 1
+.TP
.BI (net,netsplice)nodelay \fR=\fPbool
Set TCP_NODELAY on TCP connections.
.TP