**pmemblk**
Read and write using filesystem DAX to a file on a filesystem
- mounted with DAX on a persistent memory device through the NVML
+ mounted with DAX on a persistent memory device through the PMDK
libpmemblk library.
**dev-dax**
Read and write using device DAX to a persistent memory device (e.g.,
- /dev/dax0.0) through the NVML libpmem library.
+ /dev/dax0.0) through the PMDK libpmem library.
**external**
Prefix to specify loading an external I/O engine object file. Append
**libpmem**
Read and write using mmap I/O to a file on a filesystem
- mounted with DAX on a persistent memory device through the NVML
+ mounted with DAX on a persistent memory device through the PMDK
libpmem library.
I/O engine specific parameters
With writefua option set to 1, write operations include
the force unit access (fua) flag. Default is 0.
+.. option:: sg_write_mode=str : [sg]
+ Specify the type of write commands to issue. This option can take three values:
+
+ **write**
+ This is the default where write opcodes are issued as usual.
+ **verify**
+ Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 0. This
+ directs the device to carry out a medium verification with no data
+ comparison. The writefua option is ignored with this selection.
+ **same**
+ Issue WRITE SAME commands. This transfers a single block to the device
+ and writes this same block of data to a contiguous sequence of LBAs
+ beginning at the specified offset. fio's block size parameter specifies
+ the amount of data written with each command. However, the amount of data
+ actually transferred to the device is equal to the device's block
+ (sector) size. For a device with 512 byte sectors, blocksize=8k will
+ write 16 sectors with each command. fio will still generate 8k of data
+ for each command but only the first 512 bytes will be used and
+ transferred to the device. The writefua option is ignored with this
+ selection.
I/O depth
~~~~~~~~~
still respecting ordering. The result is the same I/O pattern to a given
device, but different timings.
+.. option:: replay_time_scale=int
+
+ When replaying I/O with :option:`read_iolog`, fio will honor the
+ original timing in the trace. With this option, it's possible to scale
+ the time. It's a percentage option, if set to 50 it means run at 50%
+ the original IO rate in the trace. If set to 200, run at twice the
+ original IO rate. Defaults to 100.
+
.. option:: replay_redirect=str
While replaying I/O patterns using :option:`read_iolog` the default behavior
Scale sector offsets down by this factor when replaying traces.
+.. option:: replay_skip=str
+
+ Sometimes it's useful to skip certain IO types in a replay trace.
+ This could be, for instance, eliminating the writes in the trace.
+ Or not replaying the trims/discards, if you are redirecting to
+ a device that doesn't support them. This option takes a comma
+ separated list of read, write, trim, sync.
+
Threads, processes and job synchronization
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Set the I/O priority class. See man :manpage:`ionice(1)`.
-.. option:: cpumask=int
-
- Set the CPU affinity of this job. The parameter given is a bit mask of
- allowed CPUs the job may run on. So if you want the allowed CPUs to be 1
- and 5, you would pass the decimal value of (1 << 1 | 1 << 5), or 34. See man
- :manpage:`sched_setaffinity(2)`. This may not work on all supported
- operating systems or kernel versions. This option doesn't work well for a
- higher CPU count than what you can store in an integer mask, so it can only
- control cpus 1-32. For boxes with larger CPU counts, use
- :option:`cpus_allowed`.
-
.. option:: cpus_allowed=str
Controls the same options as :option:`cpumask`, but accepts a textual
- specification of the permitted CPUs instead. So to use CPUs 1 and 5 you
- would specify ``cpus_allowed=1,5``. This option also allows a range of CPUs
- to be specified -- say you wanted a binding to CPUs 1, 5, and 8 to 15, you
- would set ``cpus_allowed=1,5,8-15``.
+ specification of the permitted CPUs instead and CPUs are indexed from 0. So
+ to use CPUs 0 and 5 you would specify ``cpus_allowed=0,5``. This option also
+ allows a range of CPUs to be specified -- say you wanted a binding to CPUs
+ 0, 5, and 8 to 15, you would set ``cpus_allowed=0,5,8-15``.
+
+ On Windows, when ``cpus_allowed`` is unset only CPUs from fio's current
+ processor group will be used and affinity settings are inherited from the
+ system. An fio build configured to target Windows 7 makes options that set
+ CPUs processor group aware and values will set both the processor group
+ and a CPU from within that group. For example, on a system where processor
+ group 0 has 40 CPUs and processor group 1 has 32 CPUs, ``cpus_allowed``
+ values between 0 and 39 will bind CPUs from processor group 0 and
+ ``cpus_allowed`` values between 40 and 71 will bind CPUs from processor
+ group 1. When using ``cpus_allowed_policy=shared`` all CPUs specified by a
+ single ``cpus_allowed`` option must be from the same processor group. For
+ Windows fio builds not built for Windows 7, CPUs will only be selected from
+ (and be relative to) whatever processor group fio happens to be running in
+ and CPUs from other processor groups cannot be used.
.. option:: cpus_allowed_policy=str
enough CPUs are given for the jobs listed, then fio will roundrobin the CPUs
in the set.
+.. option:: cpumask=int
+
+ Set the CPU affinity of this job. The parameter given is a bit mask of
+ allowed CPUs the job may run on. So if you want the allowed CPUs to be 1
+ and 5, you would pass the decimal value of (1 << 1 | 1 << 5), or 34. See man
+ :manpage:`sched_setaffinity(2)`. This may not work on all supported
+ operating systems or kernel versions. This option doesn't work well for a
+ higher CPU count than what you can store in an integer mask, so it can only
+ control cpus 1-32. For boxes with larger CPU counts, use
+ :option:`cpus_allowed`.
+
.. option:: numa_cpu_nodes=str
Set this job running on specified NUMA nodes' CPUs. The arguments allow
previously written file. If the data direction includes any form of write,
the verify will be of the newly written data.
-.. option:: verifysort=bool
-
- If true, fio will sort written verify blocks when it deems it faster to read
- them back in a sorted manner. This is often the case when overwriting an
- existing file, since the blocks are already laid out in the file system. You
- can ignore this option unless doing huge amounts of really fast I/O where
- the red-black tree sorting CPU time becomes significant. Default: true.
-
-.. option:: verifysort_nr=int
-
- Pre-load and sort verify blocks for a read workload.
-
.. option:: verify_offset=int
Swap the verification header with data somewhere else in the block before
Define the set of CPUs that are allowed to handle online log compression for
the I/O jobs. This can provide better isolation between performance
- sensitive jobs, and background compression work.
+ sensitive jobs, and background compression work. See
+ :option:`cpus_allowed` for the format used.
.. option:: log_store_compressed=bool
projects / fio.git / blobdiff