Add option for refilling IO buffers on each submit

[fio.git] / HOWTO

diff --git a/HOWTO b/HOWTO
index d8c6b9414eef85be48779d7018682cf2bbd07470..36e42aaf6b9defb210d83d0b538284bea7f6a4d6 100644 (file)
--- a/HOWTO
+++ b/HOWTO
@@ -219,6 +219,25 @@ filename=str       Fio normally makes up a filename based on the job name,
 opendir=str    Tell fio to recursively add any file it can find in this
                directory and down the file system tree.
 
+lockfile=str   Fio defaults to not doing any locking files before it does
+               IO to them. If a file or file descriptor is shared, fio
+               can serialize IO to that file to make the end result
+               consistent. This is usual for emulating real workloads that
+               share files. The lock modes are:
+
+                       none            No locking. The default.
+                       exclusive       Only one thread/process may do IO,
+                                       excluding all others.
+                       readwrite       Read-write locking on the file. Many
+                                       readers may access the file at the
+                                       same time, but writes get exclusive
+                                       access.
+
+               The option may be post-fixed with a lock batch number. If
+               set, then each thread/process may do that amount of IOs to
+               the file before giving up the lock. Since lock acqusition is
+               expensive, batching the lock/unlocks will speed up IO.
+
 readwrite=str
 rw=str         Type of io pattern. Accepted values are:
 
@@ -317,6 +336,11 @@ bs_unaligned       If this option is given, any byte size value within bsrange
 zero_buffers   If this option is given, fio will init the IO buffers to
                all zeroes. The default is to fill them with random data.
 
+refill_buffers If this option is given, fio will refill the IO buffers
+               on every submit. The default is to only fill it at init
+               time and reuse that data. Only makes sense if zero_buffers
+               isn't specified, naturally.
+
 nrfiles=int    Number of files to use for this job. Defaults to 1.
 
 openfiles=int  Number of files to keep open at the same time. Defaults to
@@ -435,7 +459,11 @@ fsync=int  If writing to a file, issue a sync of the dirty data
                not sync the file. The exception is the sg io engine, which
                synchronizes the disk cache anyway.
 
-overwrite=bool If writing to a file, setup the file first and do overwrites.
+overwrite=bool If true, writes to a file will always overwrite existing
+               data. If the file doesn't already exist, it will be
+               created before the write phase begins. If the file exists
+               and is large enough for the specified write phase, nothing
+               will be done.
 
 end_fsync=bool If true, fsync file contents when the job exits.
 
@@ -443,10 +471,6 @@ fsync_on_close=bool        If true, fio will fsync() a dirty file on close.
                This differs from end_fsync in that it will happen on every
                file close, not just at the end of the job.
 
-rwmixcycle=int Value in milliseconds describing how often to switch between
-               reads and writes for a mixed workload. The default is
-               500 msecs.
-
 rwmixread=int  How large a percentage of the mix should be reads.
 
 rwmixwrite=int How large a percentage of the mix should be writes. If both
@@ -463,6 +487,12 @@ norandommap        Normally fio will cover every block of the file when doing
                fio doesn't track potential block rewrites which may alter
                the calculated checksum for that block.
 
+softrandommap  See norandommap. If fio runs with the random block map enabled
+               and it fails to allocate the map, if this option is set it
+               will continue without a random block map. As coverage will
+               not be as complete as with random maps, this option is
+               disabled by default.
+
 nice=int       Run the job with the given nice value. See man nice(2).
 
 prio=int       Set the io priority value of this job. Linux limits us to