can be given for both read and writes. If a single int is
given, it will apply to both. If a second int is specified
after a comma, it will apply to writes only. In other words,
- the format is either bs=read_and_write or bs=read,write.
- bs=4k,8k will thus use 4k blocks for reads, and 8k blocks
- for writes. If you only wish to set the write size, you
+ the format is either bs=read_and_write or bs=read,write,trim.
+ bs=4k,8k will thus use 4k blocks for reads, 8k blocks for
+ writes, and 8k for trims. You can terminate the list with
+ a trailing comma. bs=4k,8k, would use the default value for
+ trims.. If you only wish to set the write size, you
can do so by passing an empty read size - bs=,8k will set
8k for writes and leave the read default value.
may be used as a block range. This typically wont work with
direct IO, as that normally requires sector alignment.
+bs_is_seq_rand If this option is set, fio will use the normal read,write
+ blocksize settings as sequential,random instead. Any random
+ read or write will use the WRITE blocksize settings, and any
+ sequential read or write will use the READ blocksize setting.
+
zero_buffers If this option is given, fio will init the IO buffers to
all zeroes. The default is to fill them with random data.
O_DIRECT. Note that ZFS on Solaris doesn't support direct io.
On Windows the synchronous ioengines don't support direct io.
+atomic=bool If value is true, attempt to use atomic direct IO. Atomic
+ writes are guaranteed to be stable once acknowledged by
+ the operating system. Only Linux supports O_ATOMIC right
+ now.
+
buffered=bool If value is true, use buffered io. This is the opposite
of the 'direct' option. Defaults to true.
which are intended to operate on a file in parallel in disjoint
segments, with even spacing between the starting points.
+number_ios=int Fio will normally perform IOs until it has exhausted the size
+ of the region set by size=, or if it exhaust the allocated
+ time (or hits an error condition). With this setting, the
+ range/size can be set independently of the number of IOs to
+ perform. When fio reaches this number, it will exit normally
+ and report status.
+
fsync=int If writing to a file, issue a sync of the dirty data
for every number of blocks given. For example, if you give
32 as a parameter, fio will sync the file for every 32
is fully random. It can be set from anywhere from 0 to 100.
Setting it to 0 would make the workload fully sequential. Any
setting in between will result in a random mix of sequential
- and random IO, at the given percentages.
+ and random IO, at the given percentages. It is possible to
+ set different values for reads, writes, and trim. To do so,
+ simply use a comma separated list. See blocksize.
-percentage_sequential=int See percentage_random. It is guaranteed that
- they add up to 100. The later setting has priority, each
- will adjust the other.
-
norandommap Normally fio will cover every block of the file when doing
random IO. If this option is given, fio will just get a
new random offset without looking at past io history. This
as rate, just specified independently of bandwidth. If the
job is given a block size range instead of a fixed value,
the smallest block size is used as the metric. The same format
- as rate is used for read vs write seperation.
+ as rate is used for read vs write separation.
rate_iops_min=int If fio doesn't meet this rate of IO, it will cause
the job to exit. The same format as rate is used for read vs
- write seperation.
+ write separation.
+
+latency_target=int If set, fio will attempt to find the max performance
+ point that the given workload will run at while maintaining a
+ latency below this target. The values is given in microseconds.
+ See latency_window and latency_percentile
+
+latency_window=int Used with latency_target to specify the sample window
+ that the job is run at varying queue depths to test the
+ performance. The value is given in microseconds.
+
+latency_percentile=float The percentage of IOs that must fall within the
+ criteria specified by latency_target and latency_window. If not
+ set, this defaults to 100.0, meaning that all IOs must be equal
+ or below to the value set by latency_target.
max_latency=int If set, fio will exit the job if it exceeds this maximum
latency. It will exit with an ETIME error.
holding this meta data. If this option is enabled, fio
will write only N blocks before verifying these blocks.
- will verify the previously written blocks before continuing
- to write new ones.
-
verify_backlog_batch=int Control how many blocks fio will verify
if verify_backlog is set. If not set, will default to
the value of verify_backlog (meaning the entire queue
blocks will be verified more than once.
stonewall
-wait_for_previous Wait for preceeding jobs in the job file to exit, before
+wait_for_previous Wait for preceding jobs in the job file to exit, before
starting this one. Can be used to insert serialization
points in the job file. A stone wall also implies starting
a new reporting group.
replay_redirect=str While replaying I/O patterns using read_iolog the
default behavior is to replay the IOPS onto the major/minor
device that each IOP was recorded from. This is sometimes
- undesireable because on a different machine those major/minor
+ undesirable because on a different machine those major/minor
numbers can map to a different device. Changing hardware on
the same system can also result in a different major/minor
mapping. Replay_redirect causes all IOPS to be replayed onto
and foo_lat.log. This helps fio_generate_plot fine the logs
automatically.
-write_bw_log=str If given, write an IOPS log of the jobs in this job
- file. See write_bw_log.
-
write_iops_log=str Same as write_bw_log, but writes IOPS. If no filename is
given with this option, the default filename of
"jobname_type.log" is used. Even if the filename is given,
[net] interface=str The IP address of the network interface used to send or
receive UDP multicast
+[netsplice] ttl=int
+[net] ttl=int Time-to-live value for outgoing UDP multicast packets.
+ Default: 1
+
[netsplice] nodelay=bool
[net] nodelay=bool Set TCP_NODELAY on TCP connections.
Read merges, write merges,
Read ticks, write ticks,
Time spent in queue, disk utilization percentage
- Additional Info (dependant on continue_on_error, default off): total # errors, first error code
+ Additional Info (dependent on continue_on_error, default off): total # errors, first error code
- Additional Info (dependant on description being set): Text description
+ Additional Info (dependent on description being set): Text description
Completion latency percentiles can be a grouping of up to 20 sets, so
for the terse output fio writes all of them. Each field will look like this:
projects / fio.git / blobdiff