8 5. Detailed list of parameters
13 1.0 Overview and history
14 ------------------------
15 fio was originally written to save me the hassle of writing special test
16 case programs when I wanted to test a specific workload, either for
17 performance reasons or to find/reproduce a bug. The process of writing
18 such a test app can be tiresome, especially if you have to do it often.
19 Hence I needed a tool that would be able to simulate a given io workload
20 without resorting to writing a tailored test case again and again.
22 A test work load is difficult to define, though. There can be any number
23 of processes or threads involved, and they can each be using their own
24 way of generating io. You could have someone dirtying large amounts of
25 memory in an memory mapped file, or maybe several threads issuing
26 reads using asynchronous io. fio needed to be flexible enough to
27 simulate both of these cases, and many more.
31 The first step in getting fio to simulate a desired io workload, is
32 writing a job file describing that specific setup. A job file may contain
33 any number of threads and/or files - the typical contents of the job file
34 is a global section defining shared parameters, and one or more job
35 sections describing the jobs involved. When run, fio parses this file
36 and sets everything up as described. If we break down a job from top to
37 bottom, it contains the following basic parameters:
39 IO type Defines the io pattern issued to the file(s).
40 We may only be reading sequentially from this
41 file(s), or we may be writing randomly. Or even
42 mixing reads and writes, sequentially or randomly.
44 Block size In how large chunks are we issuing io? This may be
45 a single value, or it may describe a range of
48 IO size How much data are we going to be reading/writing.
50 IO engine How do we issue io? We could be memory mapping the
51 file, we could be using regular read/write, we
52 could be using splice, async io, syslet, or even
55 IO depth If the io engine is async, how large a queuing
56 depth do we want to maintain?
58 IO type Should we be doing buffered io, or direct/raw io?
60 Num files How many files are we spreading the workload over.
62 Num threads How many threads or processes should we spread
65 The above are the basic parameters defined for a workload, in addition
66 there's a multitude of parameters that modify other aspects of how this
72 See the README file for command line parameters, there are only a few
75 Running fio is normally the easiest part - you just give it the job file
76 (or job files) as parameters:
80 and it will start doing what the job_file tells it to do. You can give
81 more than one job file on the command line, fio will serialize the running
82 of those files. Internally that is the same as using the 'stonewall'
83 parameter described the the parameter section.
85 If the job file contains only one job, you may as well just give the
86 parameters on the command line. The command line parameters are identical
87 to the job parameters, with a few extra that control global parameters
88 (see README). For example, for the job file parameter iodepth=2, the
89 mirror command line option would be --iodepth 2 or --iodepth=2. You can
90 also use the command line for giving more than one job entry. For each
91 --name option that fio sees, it will start a new job with that name.
92 Command line entries following a --name entry will apply to that job,
93 until there are no more entries or a new --name entry is seen. This is
94 similar to the job file options, where each option applies to the current
95 job until a new [] job entry is seen.
97 fio does not need to run as root, except if the files or devices specified
98 in the job section requires that. Some other options may also be restricted,
99 such as memory locking, io scheduler switching, and decreasing the nice value.
104 As previously described, fio accepts one or more job files describing
105 what it is supposed to do. The job file format is the classic ini file,
106 where the names enclosed in [] brackets define the job name. You are free
107 to use any ascii name you want, except 'global' which has special meaning.
108 A global section sets defaults for the jobs described in that file. A job
109 may override a global section parameter, and a job file may even have
110 several global sections if so desired. A job is only affected by a global
111 section residing above it. If the first character in a line is a ';' or a
112 '#', the entire line is discarded as a comment.
114 So let's look at a really simple job file that defines two processes, each
115 randomly reading from a 128MB file.
117 ; -- start job file --
128 As you can see, the job file sections themselves are empty as all the
129 described parameters are shared. As no filename= option is given, fio
130 makes up a filename for each of the jobs as it sees fit. On the command
131 line, this job would look as follows:
133 $ fio --name=global --rw=randread --size=128m --name=job1 --name=job2
136 Let's look at an example that has a number of processes writing randomly
139 ; -- start job file --
151 Here we have no global section, as we only have one job defined anyway.
152 We want to use async io here, with a depth of 4 for each file. We also
153 increased the buffer size used to 32KB and define numjobs to 4 to
154 fork 4 identical jobs. The result is 4 processes each randomly writing
155 to their own 64MB file. Instead of using the above job file, you could
156 have given the parameters on the command line. For this case, you would
159 $ fio --name=random-writers --ioengine=libaio --iodepth=4 --rw=randwrite --bs=32k --direct=0 --size=64m --numjobs=4
161 4.1 Environment variables
162 -------------------------
164 fio also supports environment variable expansion in job files. Any
165 substring of the form "${VARNAME}" as part of an option value (in other
166 words, on the right of the `='), will be expanded to the value of the
167 environment variable called VARNAME. If no such environment variable
168 is defined, or VARNAME is the empty string, the empty string will be
171 As an example, let's look at a sample fio invocation and job file:
173 $ SIZE=64m NUMJOBS=4 fio jobfile.fio
175 ; -- start job file --
182 This will expand to the following equivalent job file at runtime:
184 ; -- start job file --
191 fio ships with a few example job files, you can also look there for
194 4.2 Reserved keywords
195 ---------------------
197 Additionally, fio has a set of reserved keywords that will be replaced
198 internally with the appropriate value. Those keywords are:
200 $pagesize The architecture page size of the running system
201 $mb_memory Megabytes of total memory in the system
202 $ncpus Number of online available CPUs
204 These can be used on the command line or in the job file, and will be
205 automatically substituted with the current system values when the job
206 is run. Simple math is also supported on these keywords, so you can
207 perform actions like:
211 and get that properly expanded to 8 times the size of memory in the
215 5.0 Detailed list of parameters
216 -------------------------------
218 This section describes in details each parameter associated with a job.
219 Some parameters take an option of a given type, such as an integer or
220 a string. The following types are used:
222 str String. This is a sequence of alpha characters.
223 time Integer with possible time suffix. In seconds unless otherwise
224 specified, use eg 10m for 10 minutes. Accepts s/m/h for seconds,
226 int SI integer. A whole number value, which may contain a suffix
227 describing the base of the number. Accepted suffixes are k/m/g/t/p,
228 meaning kilo, mega, giga, tera, and peta. The suffix is not case
229 sensitive. So if you want to specify 4096, you could either write
230 out '4096' or just give 4k. The suffixes signify base 2 values, so
231 1024 is 1k and 1024k is 1m and so on. If the option accepts an upper
232 and lower range, use a colon ':' or minus '-' to separate such values.
233 May also include a prefix to indicate numbers base. If 0x is used,
234 the number is assumed to be hexadecimal. See irange.
235 bool Boolean. Usually parsed as an integer, however only defined for
236 true and false (1 and 0).
237 irange Integer range with suffix. Allows value range to be given, such
238 as 1024-4096. A colon may also be used as the separator, eg
239 1k:4k. If the option allows two sets of ranges, they can be
240 specified with a ',' or '/' delimiter: 1k-4k/8k-32k. Also see
243 With the above in mind, here follows the complete list of fio job
246 name=str ASCII name of the job. This may be used to override the
247 name printed by fio for this job. Otherwise the job
248 name is used. On the command line this parameter has the
249 special purpose of also signaling the start of a new
252 description=str Text description of the job. Doesn't do anything except
253 dump this text description when this job is run. It's
256 directory=str Prefix filenames with this directory. Used to place files
257 in a different location than "./".
259 filename=str Fio normally makes up a filename based on the job name,
260 thread number, and file number. If you want to share
261 files between threads in a job or several jobs, specify
262 a filename for each of them to override the default. If
263 the ioengine used is 'net', the filename is the host, port,
264 and protocol to use in the format of =host/port/protocol.
265 See ioengine=net for more. If the ioengine is file based, you
266 can specify a number of files by separating the names with a
267 ':' colon. So if you wanted a job to open /dev/sda and /dev/sdb
268 as the two working files, you would use
269 filename=/dev/sda:/dev/sdb. If the wanted filename does need to
270 include a colon, then escape that with a '\' character. For
271 instance, if the filename is "/dev/dsk/foo@3,0:c", then you would
272 use filename="/dev/dsk/foo@3,0\:c". '-' is a reserved name,
273 meaning stdin or stdout. Which of the two depends on the read/write
276 opendir=str Tell fio to recursively add any file it can find in this
277 directory and down the file system tree.
279 lockfile=str Fio defaults to not locking any files before it does
280 IO to them. If a file or file descriptor is shared, fio
281 can serialize IO to that file to make the end result
282 consistent. This is usual for emulating real workloads that
283 share files. The lock modes are:
285 none No locking. The default.
286 exclusive Only one thread/process may do IO,
287 excluding all others.
288 readwrite Read-write locking on the file. Many
289 readers may access the file at the
290 same time, but writes get exclusive
293 The option may be post-fixed with a lock batch number. If
294 set, then each thread/process may do that amount of IOs to
295 the file before giving up the lock. Since lock acquisition is
296 expensive, batching the lock/unlocks will speed up IO.
299 rw=str Type of io pattern. Accepted values are:
301 read Sequential reads
302 write Sequential writes
303 randwrite Random writes
304 randread Random reads
305 rw Sequential mixed reads and writes
306 randrw Random mixed reads and writes
308 For the mixed io types, the default is to split them 50/50.
309 For certain types of io the result may still be skewed a bit,
310 since the speed may be different. It is possible to specify
311 a number of IO's to do before getting a new offset - this
312 is only useful for random IO, where fio would normally
313 generate a new random offset for every IO. If you append
314 eg 8 to randread, you would get a new random offset for
315 every 8 IO's. The result would be a seek for only every 8
316 IO's, instead of for every IO. Use rw=randread:8 to specify
319 kb_base=int The base unit for a kilobyte. The defacto base is 2^10, 1024.
320 Storage manufacturers like to use 10^3 or 1000 as a base
321 ten unit instead, for obvious reasons. Allow values are
322 1024 or 1000, with 1024 being the default.
324 randrepeat=bool For random IO workloads, seed the generator in a predictable
325 way so that results are repeatable across repetitions.
327 fallocate=bool By default, fio will use fallocate() to advise the system
328 of the size of the file we are going to write. This can be
329 turned off with fallocate=0. May not be available on all
332 fadvise_hint=bool By default, fio will use fadvise() to advise the kernel
333 on what IO patterns it is likely to issue. Sometimes you
334 want to test specific IO patterns without telling the
335 kernel about it, in which case you can disable this option.
336 If set, fio will use POSIX_FADV_SEQUENTIAL for sequential
337 IO and POSIX_FADV_RANDOM for random IO.
339 size=int The total size of file io for this job. Fio will run until
340 this many bytes has been transferred, unless runtime is
341 limited by other options (such as 'runtime', for instance).
342 Unless specific nrfiles and filesize options are given,
343 fio will divide this size between the available files
344 specified by the job.
346 filesize=int Individual file sizes. May be a range, in which case fio
347 will select sizes for files at random within the given range
348 and limited to 'size' in total (if that is given). If not
349 given, each created file is the same size.
351 fill_device=bool Sets size to something really large and waits for ENOSPC (no
352 space left on device) as the terminating condition. Only makes
353 sense with sequential write. For a read workload, the mount
354 point will be filled first then IO started on the result.
357 bs=int The block size used for the io units. Defaults to 4k. Values
358 can be given for both read and writes. If a single int is
359 given, it will apply to both. If a second int is specified
360 after a comma, it will apply to writes only. In other words,
361 the format is either bs=read_and_write or bs=read,write.
362 bs=4k,8k will thus use 4k blocks for reads, and 8k blocks
363 for writes. If you only wish to set the write size, you
364 can do so by passing an empty read size - bs=,8k will set
365 8k for writes and leave the read default value.
368 ba=int At what boundary to align random IO offsets. Defaults to
369 the same as 'blocksize' the minimum blocksize given.
370 Minimum alignment is typically 512b for using direct IO,
371 though it usually depends on the hardware block size. This
372 option is mutually exclusive with using a random map for
373 files, so it will turn off that option.
375 blocksize_range=irange
376 bsrange=irange Instead of giving a single block size, specify a range
377 and fio will mix the issued io block sizes. The issued
378 io unit will always be a multiple of the minimum value
379 given (also see bs_unaligned). Applies to both reads and
380 writes, however a second range can be given after a comma.
383 bssplit=str Sometimes you want even finer grained control of the
384 block sizes issued, not just an even split between them.
385 This option allows you to weight various block sizes,
386 so that you are able to define a specific amount of
387 block sizes issued. The format for this option is:
389 bssplit=blocksize/percentage:blocksize/percentage
391 for as many block sizes as needed. So if you want to define
392 a workload that has 50% 64k blocks, 10% 4k blocks, and
393 40% 32k blocks, you would write:
395 bssplit=4k/10:64k/50:32k/40
397 Ordering does not matter. If the percentage is left blank,
398 fio will fill in the remaining values evenly. So a bssplit
399 option like this one:
401 bssplit=4k/50:1k/:32k/
403 would have 50% 4k ios, and 25% 1k and 32k ios. The percentages
404 always add up to 100, if bssplit is given a range that adds
405 up to more, it will error out.
407 bssplit also supports giving separate splits to reads and
408 writes. The format is identical to what bs= accepts. You
409 have to separate the read and write parts with a comma. So
410 if you want a workload that has 50% 2k reads and 50% 4k reads,
411 while having 90% 4k writes and 10% 8k writes, you would
414 bssplit=2k/50:4k/50,4k/90,8k/10
417 bs_unaligned If this option is given, any byte size value within bsrange
418 may be used as a block range. This typically wont work with
419 direct IO, as that normally requires sector alignment.
421 zero_buffers If this option is given, fio will init the IO buffers to
422 all zeroes. The default is to fill them with random data.
424 refill_buffers If this option is given, fio will refill the IO buffers
425 on every submit. The default is to only fill it at init
426 time and reuse that data. Only makes sense if zero_buffers
427 isn't specified, naturally. If data verification is enabled,
428 refill_buffers is also automatically enabled.
430 nrfiles=int Number of files to use for this job. Defaults to 1.
432 openfiles=int Number of files to keep open at the same time. Defaults to
433 the same as nrfiles, can be set smaller to limit the number
436 file_service_type=str Defines how fio decides which file from a job to
437 service next. The following types are defined:
439 random Just choose a file at random.
441 roundrobin Round robin over open files. This
444 sequential Finish one file before moving on to
445 the next. Multiple files can still be
446 open depending on 'openfiles'.
448 The string can have a number appended, indicating how
449 often to switch to a new file. So if option random:4 is
450 given, fio will switch to a new random file after 4 ios
453 ioengine=str Defines how the job issues io to the file. The following
456 sync Basic read(2) or write(2) io. lseek(2) is
457 used to position the io location.
459 psync Basic pread(2) or pwrite(2) io.
461 vsync Basic readv(2) or writev(2) IO.
463 libaio Linux native asynchronous io. Note that Linux
464 may only support queued behaviour with
465 non-buffered IO (set direct=1 or buffered=0).
467 posixaio glibc posix asynchronous io.
469 solarisaio Solaris native asynchronous io.
471 mmap File is memory mapped and data copied
472 to/from using memcpy(3).
474 splice splice(2) is used to transfer the data and
475 vmsplice(2) to transfer data from user
478 syslet-rw Use the syslet system calls to make
479 regular read/write async.
481 sg SCSI generic sg v3 io. May either be
482 synchronous using the SG_IO ioctl, or if
483 the target is an sg character device
484 we use read(2) and write(2) for asynchronous
487 null Doesn't transfer any data, just pretends
488 to. This is mainly used to exercise fio
489 itself and for debugging/testing purposes.
491 net Transfer over the network to given host:port.
492 'filename' must be set appropriately to
493 filename=host/port/protocol regardless of send
494 or receive, if the latter only the port
495 argument is used. 'host' may be an IP address
496 or hostname, port is the port number to be used,
497 and protocol may be 'udp' or 'tcp'. If no
498 protocol is given, TCP is used.
500 netsplice Like net, but uses splice/vmsplice to
501 map data and send/receive.
503 cpuio Doesn't transfer any data, but burns CPU
504 cycles according to the cpuload= and
505 cpucycle= options. Setting cpuload=85
506 will cause that job to do nothing but burn
507 85% of the CPU. In case of SMP machines,
508 use numjobs=<no_of_cpu> to get desired CPU
509 usage, as the cpuload only loads a single
510 CPU at the desired rate.
512 guasi The GUASI IO engine is the Generic Userspace
513 Asyncronous Syscall Interface approach
516 http://www.xmailserver.org/guasi-lib.html
518 for more info on GUASI.
520 external Prefix to specify loading an external
521 IO engine object file. Append the engine
522 filename, eg ioengine=external:/tmp/foo.o
523 to load ioengine foo.o in /tmp.
525 iodepth=int This defines how many io units to keep in flight against
526 the file. The default is 1 for each file defined in this
527 job, can be overridden with a larger value for higher
530 iodepth_batch_submit=int
531 iodepth_batch=int This defines how many pieces of IO to submit at once.
532 It defaults to 1 which means that we submit each IO
533 as soon as it is available, but can be raised to submit
534 bigger batches of IO at the time.
536 iodepth_batch_complete=int This defines how many pieces of IO to retrieve
537 at once. It defaults to 1 which means that we'll ask
538 for a minimum of 1 IO in the retrieval process from
539 the kernel. The IO retrieval will go on until we
540 hit the limit set by iodepth_low. If this variable is
541 set to 0, then fio will always check for completed
542 events before queuing more IO. This helps reduce
543 IO latency, at the cost of more retrieval system calls.
545 iodepth_low=int The low water mark indicating when to start filling
546 the queue again. Defaults to the same as iodepth, meaning
547 that fio will attempt to keep the queue full at all times.
548 If iodepth is set to eg 16 and iodepth_low is set to 4, then
549 after fio has filled the queue of 16 requests, it will let
550 the depth drain down to 4 before starting to fill it again.
552 direct=bool If value is true, use non-buffered io. This is usually
555 buffered=bool If value is true, use buffered io. This is the opposite
556 of the 'direct' option. Defaults to true.
558 offset=int Start io at the given offset in the file. The data before
559 the given offset will not be touched. This effectively
560 caps the file size at real_size - offset.
562 fsync=int If writing to a file, issue a sync of the dirty data
563 for every number of blocks given. For example, if you give
564 32 as a parameter, fio will sync the file for every 32
565 writes issued. If fio is using non-buffered io, we may
566 not sync the file. The exception is the sg io engine, which
567 synchronizes the disk cache anyway.
569 fsyncdata=int Like fsync= but uses fdatasync() to only sync data and not
572 overwrite=bool If true, writes to a file will always overwrite existing
573 data. If the file doesn't already exist, it will be
574 created before the write phase begins. If the file exists
575 and is large enough for the specified write phase, nothing
578 end_fsync=bool If true, fsync file contents when the job exits.
580 fsync_on_close=bool If true, fio will fsync() a dirty file on close.
581 This differs from end_fsync in that it will happen on every
582 file close, not just at the end of the job.
584 rwmixread=int How large a percentage of the mix should be reads.
586 rwmixwrite=int How large a percentage of the mix should be writes. If both
587 rwmixread and rwmixwrite is given and the values do not add
588 up to 100%, the latter of the two will be used to override
589 the first. This may interfere with a given rate setting,
590 if fio is asked to limit reads or writes to a certain rate.
591 If that is the case, then the distribution may be skewed.
593 norandommap Normally fio will cover every block of the file when doing
594 random IO. If this option is given, fio will just get a
595 new random offset without looking at past io history. This
596 means that some blocks may not be read or written, and that
597 some blocks may be read/written more than once. This option
598 is mutually exclusive with verify= if and only if multiple
599 blocksizes (via bsrange=) are used, since fio only tracks
600 complete rewrites of blocks.
602 softrandommap See norandommap. If fio runs with the random block map enabled
603 and it fails to allocate the map, if this option is set it
604 will continue without a random block map. As coverage will
605 not be as complete as with random maps, this option is
608 nice=int Run the job with the given nice value. See man nice(2).
610 prio=int Set the io priority value of this job. Linux limits us to
611 a positive value between 0 and 7, with 0 being the highest.
614 prioclass=int Set the io priority class. See man ionice(1).
616 thinktime=int Stall the job x microseconds after an io has completed before
617 issuing the next. May be used to simulate processing being
618 done by an application. See thinktime_blocks and
622 Only valid if thinktime is set - pretend to spend CPU time
623 doing something with the data received, before falling back
624 to sleeping for the rest of the period specified by
628 Only valid if thinktime is set - control how many blocks
629 to issue, before waiting 'thinktime' usecs. If not set,
630 defaults to 1 which will make fio wait 'thinktime' usecs
633 rate=int Cap the bandwidth used by this job. The number is in bytes/sec,
634 the normal suffix rules apply. You can use rate=500k to limit
635 reads and writes to 500k each, or you can specify read and
636 writes separately. Using rate=1m,500k would limit reads to
637 1MB/sec and writes to 500KB/sec. Capping only reads or
638 writes can be done with rate=,500k or rate=500k,. The former
639 will only limit writes (to 500KB/sec), the latter will only
642 ratemin=int Tell fio to do whatever it can to maintain at least this
643 bandwidth. Failing to meet this requirement, will cause
644 the job to exit. The same format as rate is used for
645 read vs write separation.
647 rate_iops=int Cap the bandwidth to this number of IOPS. Basically the same
648 as rate, just specified independently of bandwidth. If the
649 job is given a block size range instead of a fixed value,
650 the smallest block size is used as the metric. The same format
651 as rate is used for read vs write seperation.
653 rate_iops_min=int If fio doesn't meet this rate of IO, it will cause
654 the job to exit. The same format as rate is used for read vs
657 ratecycle=int Average bandwidth for 'rate' and 'ratemin' over this number
660 cpumask=int Set the CPU affinity of this job. The parameter given is a
661 bitmask of allowed CPU's the job may run on. So if you want
662 the allowed CPUs to be 1 and 5, you would pass the decimal
663 value of (1 << 1 | 1 << 5), or 34. See man
664 sched_setaffinity(2). This may not work on all supported
665 operating systems or kernel versions. This option doesn't
666 work well for a higher CPU count than what you can store in
667 an integer mask, so it can only control cpus 1-32. For
668 boxes with larger CPU counts, use cpus_allowed.
670 cpus_allowed=str Controls the same options as cpumask, but it allows a text
671 setting of the permitted CPUs instead. So to use CPUs 1 and
672 5, you would specify cpus_allowed=1,5. This options also
673 allows a range of CPUs. Say you wanted a binding to CPUs
674 1, 5, and 8-15, you would set cpus_allowed=1,5,8-15.
676 startdelay=time Start this job the specified number of seconds after fio
677 has started. Only useful if the job file contains several
678 jobs, and you want to delay starting some jobs to a certain
681 runtime=time Tell fio to terminate processing after the specified number
682 of seconds. It can be quite hard to determine for how long
683 a specified job will run, so this parameter is handy to
684 cap the total runtime to a given time.
686 time_based If set, fio will run for the duration of the runtime
687 specified even if the file(s) are completely read or
688 written. It will simply loop over the same workload
689 as many times as the runtime allows.
691 ramp_time=time If set, fio will run the specified workload for this amount
692 of time before logging any performance numbers. Useful for
693 letting performance settle before logging results, thus
694 minimizing the runtime required for stable results. Note
695 that the ramp_time is considered lead in time for a job,
696 thus it will increase the total runtime if a special timeout
697 or runtime is specified.
699 invalidate=bool Invalidate the buffer/page cache parts for this file prior
700 to starting io. Defaults to true.
702 sync=bool Use sync io for buffered writes. For the majority of the
703 io engines, this means using O_SYNC.
706 mem=str Fio can use various types of memory as the io unit buffer.
707 The allowed values are:
709 malloc Use memory from malloc(3) as the buffers.
711 shm Use shared memory as the buffers. Allocated
714 shmhuge Same as shm, but use huge pages as backing.
716 mmap Use mmap to allocate buffers. May either be
717 anonymous memory, or can be file backed if
718 a filename is given after the option. The
719 format is mem=mmap:/path/to/file.
721 mmaphuge Use a memory mapped huge file as the buffer
722 backing. Append filename after mmaphuge, ala
723 mem=mmaphuge:/hugetlbfs/file
725 The area allocated is a function of the maximum allowed
726 bs size for the job, multiplied by the io depth given. Note
727 that for shmhuge and mmaphuge to work, the system must have
728 free huge pages allocated. This can normally be checked
729 and set by reading/writing /proc/sys/vm/nr_hugepages on a
730 Linux system. Fio assumes a huge page is 4MB in size. So
731 to calculate the number of huge pages you need for a given
732 job file, add up the io depth of all jobs (normally one unless
733 iodepth= is used) and multiply by the maximum bs set. Then
734 divide that number by the huge page size. You can see the
735 size of the huge pages in /proc/meminfo. If no huge pages
736 are allocated by having a non-zero number in nr_hugepages,
737 using mmaphuge or shmhuge will fail. Also see hugepage-size.
739 mmaphuge also needs to have hugetlbfs mounted and the file
740 location should point there. So if it's mounted in /huge,
741 you would use mem=mmaphuge:/huge/somefile.
743 iomem_align=int This indiciates the memory alignment of the IO memory buffers.
744 Note that the given alignment is applied to the first IO unit
745 buffer, if using iodepth the alignment of the following buffers
746 are given by the bs used. In other words, if using a bs that is
747 a multiple of the page sized in the system, all buffers will
748 be aligned to this value. If using a bs that is not page
749 aligned, the alignment of subsequent IO memory buffers is the
750 sum of the iomem_align and bs used.
753 Defines the size of a huge page. Must at least be equal
754 to the system setting, see /proc/meminfo. Defaults to 4MB.
755 Should probably always be a multiple of megabytes, so using
756 hugepage-size=Xm is the preferred way to set this to avoid
757 setting a non-pow-2 bad value.
759 exitall When one job finishes, terminate the rest. The default is
760 to wait for each job to finish, sometimes that is not the
763 bwavgtime=int Average the calculated bandwidth over the given time. Value
764 is specified in milliseconds.
766 create_serialize=bool If true, serialize the file creating for the jobs.
767 This may be handy to avoid interleaving of data
768 files, which may greatly depend on the filesystem
769 used and even the number of processors in the system.
771 create_fsync=bool fsync the data file after creation. This is the
774 create_on_open=bool Don't pre-setup the files for IO, just create open()
775 when it's time to do IO to that file.
777 pre_read=bool If this is given, files will be pre-read into memory before
778 starting the given IO operation. This will also clear
779 the 'invalidate' flag, since it is pointless to pre-read
780 and then drop the cache. This will only work for IO engines
781 that are seekable, since they allow you to read the same data
782 multiple times. Thus it will not work on eg network or splice
785 unlink=bool Unlink the job files when done. Not the default, as repeated
786 runs of that job would then waste time recreating the file
789 loops=int Run the specified number of iterations of this job. Used
790 to repeat the same workload a given number of times. Defaults
793 do_verify=bool Run the verify phase after a write phase. Only makes sense if
794 verify is set. Defaults to 1.
796 verify=str If writing to a file, fio can verify the file contents
797 after each iteration of the job. The allowed values are:
799 md5 Use an md5 sum of the data area and store
800 it in the header of each block.
802 crc64 Use an experimental crc64 sum of the data
803 area and store it in the header of each
806 crc32c Use a crc32c sum of the data area and store
807 it in the header of each block.
809 crc32c-intel Use hardware assisted crc32c calcuation
810 provided on SSE4.2 enabled processors.
812 crc32 Use a crc32 sum of the data area and store
813 it in the header of each block.
815 crc16 Use a crc16 sum of the data area and store
816 it in the header of each block.
818 crc7 Use a crc7 sum of the data area and store
819 it in the header of each block.
821 sha512 Use sha512 as the checksum function.
823 sha256 Use sha256 as the checksum function.
825 sha1 Use optimized sha1 as the checksum function.
827 meta Write extra information about each io
828 (timestamp, block number etc.). The block
831 null Only pretend to verify. Useful for testing
832 internals with ioengine=null, not for much
835 This option can be used for repeated burn-in tests of a
836 system to make sure that the written data is also
837 correctly read back. If the data direction given is
838 a read or random read, fio will assume that it should
839 verify a previously written file. If the data direction
840 includes any form of write, the verify will be of the
843 verifysort=bool If set, fio will sort written verify blocks when it deems
844 it faster to read them back in a sorted manner. This is
845 often the case when overwriting an existing file, since
846 the blocks are already laid out in the file system. You
847 can ignore this option unless doing huge amounts of really
848 fast IO where the red-black tree sorting CPU time becomes
851 verify_offset=int Swap the verification header with data somewhere else
852 in the block before writing. Its swapped back before
855 verify_interval=int Write the verification header at a finer granularity
856 than the blocksize. It will be written for chunks the
857 size of header_interval. blocksize should divide this
860 verify_pattern=str If set, fio will fill the io buffers with this
861 pattern. Fio defaults to filling with totally random
862 bytes, but sometimes it's interesting to fill with a known
863 pattern for io verification purposes. Depending on the
864 width of the pattern, fio will fill 1/2/3/4 bytes of the
865 buffer at the time(it can be either a decimal or a hex number).
866 The verify_pattern if larger than a 32-bit quantity has to
867 be a hex number that starts with either "0x" or "0X".
869 verify_fatal=bool Normally fio will keep checking the entire contents
870 before quitting on a block verification failure. If this
871 option is set, fio will exit the job on the first observed
874 verify_async=int Fio will normally verify IO inline from the submitting
875 thread. This option takes an integer describing how many
876 async offload threads to create for IO verification instead,
877 causing fio to offload the duty of verifying IO contents
878 to one or more separate threads. If using this offload
879 option, even sync IO engines can benefit from using an
880 iodepth setting higher than 1, as it allows them to have
881 IO in flight while verifies are running.
883 verify_async_cpus=str Tell fio to set the given CPU affinity on the
884 async IO verification threads. See cpus_allowed for the
887 stonewall Wait for preceeding jobs in the job file to exit, before
888 starting this one. Can be used to insert serialization
889 points in the job file. A stone wall also implies starting
890 a new reporting group.
892 new_group Start a new reporting group. If this option isn't given,
893 jobs in a file will be part of the same reporting group
894 unless separated by a stone wall (or if it's a group
895 by itself, with the numjobs option).
897 numjobs=int Create the specified number of clones of this job. May be
898 used to setup a larger number of threads/processes doing
899 the same thing. We regard that grouping of jobs as a
902 group_reporting If 'numjobs' is set, it may be interesting to display
903 statistics for the group as a whole instead of for each
904 individual job. This is especially true of 'numjobs' is
905 large, looking at individual thread/process output quickly
906 becomes unwieldy. If 'group_reporting' is specified, fio
907 will show the final report per-group instead of per-job.
909 thread fio defaults to forking jobs, however if this option is
910 given, fio will use pthread_create(3) to create threads
913 zonesize=int Divide a file into zones of the specified size. See zoneskip.
915 zoneskip=int Skip the specified number of bytes when zonesize data has
916 been read. The two zone options can be used to only do
917 io on zones of a file.
919 write_iolog=str Write the issued io patterns to the specified file. See
922 read_iolog=str Open an iolog with the specified file name and replay the
923 io patterns it contains. This can be used to store a
924 workload and replay it sometime later. The iolog given
925 may also be a blktrace binary file, which allows fio
926 to replay a workload captured by blktrace. See blktrace
927 for how to capture such logging data. For blktrace replay,
928 the file needs to be turned into a blkparse binary data
929 file first (blktrace <device> -d file_for_fio.bin).
931 write_bw_log=str If given, write a bandwidth log of the jobs in this job
932 file. Can be used to store data of the bandwidth of the
933 jobs in their lifetime. The included fio_generate_plots
934 script uses gnuplot to turn these text files into nice
935 graphs. See write_log_log for behaviour of given
936 filename. For this option, the postfix is _bw.log.
938 write_lat_log=str Same as write_bw_log, except that this option stores io
939 completion latencies instead. If no filename is given
940 with this option, the default filename of "jobname_type.log"
941 is used. Even if the filename is given, fio will still
942 append the type of log. So if one specifies
946 The actual log names will be foo_clat.log and foo_slat.log.
947 This helps fio_generate_plot fine the logs automatically.
949 lockmem=int Pin down the specified amount of memory with mlock(2). Can
950 potentially be used instead of removing memory or booting
951 with less memory to simulate a smaller amount of memory.
953 exec_prerun=str Before running this job, issue the command specified
956 exec_postrun=str After the job completes, issue the command specified
959 ioscheduler=str Attempt to switch the device hosting the file to the specified
960 io scheduler before running.
962 cpuload=int If the job is a CPU cycle eater, attempt to use the specified
963 percentage of CPU cycles.
965 cpuchunks=int If the job is a CPU cycle eater, split the load into
966 cycles of the given time. In microseconds.
968 disk_util=bool Generate disk utilization statistics, if the platform
969 supports it. Defaults to on.
971 disable_clat=bool Disable measurements of completion latency numbers. Useful
972 only for cutting back the number of calls to gettimeofday,
973 as that does impact performance at really high IOPS rates.
974 Note that to really get rid of a large amount of these
975 calls, this option must be used with disable_slat and
978 disable_slat=bool Disable measurements of submission latency numbers. See
981 disable_bw=bool Disable measurements of throughput/bandwidth numbers. See
984 gtod_reduce=bool Enable all of the gettimeofday() reducing options
985 (disable_clat, disable_slat, disable_bw) plus reduce
986 precision of the timeout somewhat to really shrink
987 the gettimeofday() call count. With this option enabled,
988 we only do about 0.4% of the gtod() calls we would have
989 done if all time keeping was enabled.
991 gtod_cpu=int Sometimes it's cheaper to dedicate a single thread of
992 execution to just getting the current time. Fio (and
993 databases, for instance) are very intensive on gettimeofday()
994 calls. With this option, you can set one CPU aside for
995 doing nothing but logging current time to a shared memory
996 location. Then the other threads/processes that run IO
997 workloads need only copy that segment, instead of entering
998 the kernel with a gettimeofday() call. The CPU set aside
999 for doing these time calls will be excluded from other
1000 uses. Fio will manually clear it from the CPU mask of other
1003 continue_on_error=bool Normally fio will exit the job on the first observed
1004 failure. If this option is set, fio will continue the job when
1005 there is a 'non-fatal error' (EIO or EILSEQ) until the runtime
1006 is exceeded or the I/O size specified is completed. If this
1007 option is used, there are two more stats that are appended,
1008 the total error count and the first error. The error field
1009 given in the stats is the first error that was hit during the
1012 cgroup=str Add job to this control group. If it doesn't exist, it will
1013 be created. The system must have a mounted cgroup blkio
1014 mount point for this to work. If your system doesn't have it
1015 mounted, you can do so with:
1017 # mount -t cgroup -o blkio none /cgroup
1019 cgroup_weight=int Set the weight of the cgroup to this value. See
1020 the documentation that comes with the kernel, allowed values
1021 are in the range of 100..1000.
1023 uid=int Instead of running as the invoking user, set the user ID to
1024 this value before the thread/process does any work.
1026 gid=int Set group ID, see uid.
1028 6.0 Interpreting the output
1029 ---------------------------
1031 fio spits out a lot of output. While running, fio will display the
1032 status of the jobs created. An example of that would be:
1034 Threads: 1: [_r] [24.8% done] [ 13509/ 8334 kb/s] [eta 00h:01m:31s]
1036 The characters inside the square brackets denote the current status of
1037 each thread. The possible values (in typical life cycle order) are:
1041 P Thread setup, but not started.
1043 I Thread initialized, waiting.
1044 p Thread running pre-reading file(s).
1045 R Running, doing sequential reads.
1046 r Running, doing random reads.
1047 W Running, doing sequential writes.
1048 w Running, doing random writes.
1049 M Running, doing mixed sequential reads/writes.
1050 m Running, doing mixed random reads/writes.
1051 F Running, currently waiting for fsync()
1052 V Running, doing verification of written data.
1053 E Thread exited, not reaped by main thread yet.
1056 The other values are fairly self explanatory - number of threads
1057 currently running and doing io, rate of io since last check (read speed
1058 listed first, then write speed), and the estimated completion percentage
1059 and time for the running group. It's impossible to estimate runtime of
1060 the following groups (if any).
1062 When fio is done (or interrupted by ctrl-c), it will show the data for
1063 each thread, group of threads, and disks in that order. For each data
1064 direction, the output looks like:
1066 Client1 (g=0): err= 0:
1067 write: io= 32MB, bw= 666KB/s, runt= 50320msec
1068 slat (msec): min= 0, max= 136, avg= 0.03, stdev= 1.92
1069 clat (msec): min= 0, max= 631, avg=48.50, stdev=86.82
1070 bw (KB/s) : min= 0, max= 1196, per=51.00%, avg=664.02, stdev=681.68
1071 cpu : usr=1.49%, sys=0.25%, ctx=7969, majf=0, minf=17
1072 IO depths : 1=0.1%, 2=0.3%, 4=0.5%, 8=99.0%, 16=0.0%, 32=0.0%, >32=0.0%
1073 submit : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0%
1074 complete : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0%
1075 issued r/w: total=0/32768, short=0/0
1076 lat (msec): 2=1.6%, 4=0.0%, 10=3.2%, 20=12.8%, 50=38.4%, 100=24.8%,
1077 lat (msec): 250=15.2%, 500=0.0%, 750=0.0%, 1000=0.0%, >=2048=0.0%
1079 The client number is printed, along with the group id and error of that
1080 thread. Below is the io statistics, here for writes. In the order listed,
1083 io= Number of megabytes io performed
1084 bw= Average bandwidth rate
1085 runt= The runtime of that thread
1086 slat= Submission latency (avg being the average, stdev being the
1087 standard deviation). This is the time it took to submit
1088 the io. For sync io, the slat is really the completion
1089 latency, since queue/complete is one operation there. This
1090 value can be in milliseconds or microseconds, fio will choose
1091 the most appropriate base and print that. In the example
1092 above, milliseconds is the best scale.
1093 clat= Completion latency. Same names as slat, this denotes the
1094 time from submission to completion of the io pieces. For
1095 sync io, clat will usually be equal (or very close) to 0,
1096 as the time from submit to complete is basically just
1097 CPU time (io has already been done, see slat explanation).
1098 bw= Bandwidth. Same names as the xlat stats, but also includes
1099 an approximate percentage of total aggregate bandwidth
1100 this thread received in this group. This last value is
1101 only really useful if the threads in this group are on the
1102 same disk, since they are then competing for disk access.
1103 cpu= CPU usage. User and system time, along with the number
1104 of context switches this thread went through, usage of
1105 system and user time, and finally the number of major
1106 and minor page faults.
1107 IO depths= The distribution of io depths over the job life time. The
1108 numbers are divided into powers of 2, so for example the
1109 16= entries includes depths up to that value but higher
1110 than the previous entry. In other words, it covers the
1111 range from 16 to 31.
1112 IO submit= How many pieces of IO were submitting in a single submit
1113 call. Each entry denotes that amount and below, until
1114 the previous entry - eg, 8=100% mean that we submitted
1115 anywhere in between 5-8 ios per submit call.
1116 IO complete= Like the above submit number, but for completions instead.
1117 IO issued= The number of read/write requests issued, and how many
1119 IO latencies= The distribution of IO completion latencies. This is the
1120 time from when IO leaves fio and when it gets completed.
1121 The numbers follow the same pattern as the IO depths,
1122 meaning that 2=1.6% means that 1.6% of the IO completed
1123 within 2 msecs, 20=12.8% means that 12.8% of the IO
1124 took more than 10 msecs, but less than (or equal to) 20 msecs.
1126 After each client has been listed, the group statistics are printed. They
1127 will look like this:
1129 Run status group 0 (all jobs):
1130 READ: io=64MB, aggrb=22178, minb=11355, maxb=11814, mint=2840msec, maxt=2955msec
1131 WRITE: io=64MB, aggrb=1302, minb=666, maxb=669, mint=50093msec, maxt=50320msec
1133 For each data direction, it prints:
1135 io= Number of megabytes io performed.
1136 aggrb= Aggregate bandwidth of threads in this group.
1137 minb= The minimum average bandwidth a thread saw.
1138 maxb= The maximum average bandwidth a thread saw.
1139 mint= The smallest runtime of the threads in that group.
1140 maxt= The longest runtime of the threads in that group.
1142 And finally, the disk statistics are printed. They will look like this:
1144 Disk stats (read/write):
1145 sda: ios=16398/16511, merge=30/162, ticks=6853/819634, in_queue=826487, util=100.00%
1147 Each value is printed for both reads and writes, with reads first. The
1150 ios= Number of ios performed by all groups.
1151 merge= Number of merges io the io scheduler.
1152 ticks= Number of ticks we kept the disk busy.
1153 io_queue= Total time spent in the disk queue.
1154 util= The disk utilization. A value of 100% means we kept the disk
1155 busy constantly, 50% would be a disk idling half of the time.
1161 For scripted usage where you typically want to generate tables or graphs
1162 of the results, fio can output the results in a semicolon separated format.
1163 The format is one long line of values, such as:
1165 client1;0;0;1906777;1090804;1790;0;0;0.000000;0.000000;0;0;0.000000;0.000000;929380;1152890;25.510151%;1078276.333333;128948.113404;0;0;0;0;0;0.000000;0.000000;0;0;0.000000;0.000000;0;0;0.000000%;0.000000;0.000000;100.000000%;0.000000%;324;100.0%;0.0%;0.0%;0.0%;0.0%;0.0%;0.0%;100.0%;0.0%;0.0%;0.0%;0.0%;0.0%
1166 ;0.0%;0.0%;0.0%;0.0%;0.0%
1168 To enable terse output, use the --minimal command line option.
1170 Split up, the format is as follows:
1172 jobname, groupid, error
1174 KB IO, bandwidth (KB/sec), runtime (msec)
1175 Submission latency: min, max, mean, deviation
1176 Completion latency: min, max, mean, deviation
1177 Bw: min, max, aggregate percentage of total, mean, deviation
1179 KB IO, bandwidth (KB/sec), runtime (msec)
1180 Submission latency: min, max, mean, deviation
1181 Completion latency: min, max, mean, deviation
1182 Bw: min, max, aggregate percentage of total, mean, deviation
1183 CPU usage: user, system, context switches, major faults, minor faults
1184 IO depths: <=1, 2, 4, 8, 16, 32, >=64
1185 IO latencies: <=2, 4, 10, 20, 50, 100, 250, 500, 750, 1000, >=2000