git.kernel.dk Git - linux-2.6-block.git/log

net: stmmac: Set MAC's flow control register to reflect current settings

commit cc3d2b5fc0d6f8ad8a52da5ea679e5c2ec2adbd4 upstream.

Currently, pause frame register GMAC_RX_FLOW_CTRL_RFE is not updated
correctly when 'ethtool -A <IFACE> autoneg off rx off tx off' command
is issued. This fix ensures the flow control change is reflected directly
in the GMAC_RX_FLOW_CTRL_RFE register.

Fixes: 46f69ded988d ("net: stmmac: Use resolved link config in mac_link_up()")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Goh, Wei Sheng <wei.sheng.goh@intel.com>
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pinctrl: intel: Save and restore pins in "direct IRQ" mode

commit 6989ea4881c8944fbf04378418bb1af63d875ef8 upstream.

The firmware on some systems may configure GPIO pins to be
an interrupt source in so called "direct IRQ" mode. In such
cases the GPIO controller driver has no idea if those pins
are being used or not. At the same time, there is a known bug
in the firmwares that don't restore the pin settings correctly
after suspend, i.e. by an unknown reason the Rx value becomes
inverted.

Hence, let's save and restore the pins that are configured
as GPIOs in the input mode with GPIROUTIOXAPIC bit set.

Cc: stable@vger.kernel.org
Reported-and-tested-by: Dale Smith <dalepsmith@gmail.com>
Reported-and-tested-by: John Harris <jmharris@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214749
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221124222926.72326-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/bugs: Make sure MSR_SPEC_CTRL is updated properly upon resume from S3

commit 66065157420c5b9b3f078f43d313c153e1ff7f83 upstream.

The "force" argument to write_spec_ctrl_current() is currently ambiguous
as it does not guarantee the MSR write. This is due to the optimization
that writes to the MSR happen only when the new value differs from the
cached value.

This is fine in most cases, but breaks for S3 resume when the cached MSR
value gets out of sync with the hardware MSR value due to S3 resetting
it.

When x86_spec_ctrl_current is same as x86_spec_ctrl_base, the MSR write
is skipped. Which results in SPEC_CTRL mitigations not getting restored.

Move the MSR write from write_spec_ctrl_current() to a new function that
unconditionally writes to the MSR. Update the callers accordingly and
rename functions.

[ bp: Rework a bit. ]

Fixes: caa0ff24d5d0 ("x86/bugs: Keep a per-CPU IA32_SPEC_CTRL value")
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/806d39b0bfec2fe8f50dc5446dff20f5bb24a959.1669821572.git.pawan.kumar.gupta@linux.intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nilfs2: fix NULL pointer dereference in nilfs_palloc_commit_free_entry()

commit f0a0ccda18d6fd826d7c7e7ad48a6ed61c20f8b4 upstream.

Syzbot reported a null-ptr-deref bug:

NILFS (loop0): segctord starting. Construction interval = 5 seconds, CP
frequency < 30 seconds
general protection fault, probably for non-canonical address
0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 1 PID: 3603 Comm: segctord Not tainted
6.1.0-rc2-syzkaller-00105-gb229b6ca5abb #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google
10/11/2022
RIP: 0010:nilfs_palloc_commit_free_entry+0xe5/0x6b0
fs/nilfs2/alloc.c:608
Code: 00 00 00 00 fc ff df 80 3c 02 00 0f 85 cd 05 00 00 48 b8 00 00 00
00 00 fc ff df 4c 8b 73 08 49 8d 7e 10 48 89 fa 48 c1 ea 03 <80> 3c 02
00 0f 85 26 05 00 00 49 8b 46 10 be a6 00 00 00 48 c7 c7
RSP: 0018:ffffc90003dff830 EFLAGS: 00010212
RAX: dffffc0000000000 RBX: ffff88802594e218 RCX: 000000000000000d
RDX: 0000000000000002 RSI: 0000000000002000 RDI: 0000000000000010
RBP: ffff888071880222 R08: 0000000000000005 R09: 000000000000003f
R10: 000000000000000d R11: 0000000000000000 R12: ffff888071880158
R13: ffff88802594e220 R14: 0000000000000000 R15: 0000000000000004
FS:  0000000000000000(0000) GS:ffff8880b9b00000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb1c08316a8 CR3: 0000000018560000 CR4: 0000000000350ee0
Call Trace:
  <TASK>
  nilfs_dat_commit_free fs/nilfs2/dat.c:114 [inline]
  nilfs_dat_commit_end+0x464/0x5f0 fs/nilfs2/dat.c:193
  nilfs_dat_commit_update+0x26/0x40 fs/nilfs2/dat.c:236
  nilfs_btree_commit_update_v+0x87/0x4a0 fs/nilfs2/btree.c:1940
  nilfs_btree_commit_propagate_v fs/nilfs2/btree.c:2016 [inline]
  nilfs_btree_propagate_v fs/nilfs2/btree.c:2046 [inline]
  nilfs_btree_propagate+0xa00/0xd60 fs/nilfs2/btree.c:2088
  nilfs_bmap_propagate+0x73/0x170 fs/nilfs2/bmap.c:337
  nilfs_collect_file_data+0x45/0xd0 fs/nilfs2/segment.c:568
  nilfs_segctor_apply_buffers+0x14a/0x470 fs/nilfs2/segment.c:1018
  nilfs_segctor_scan_file+0x3f4/0x6f0 fs/nilfs2/segment.c:1067
  nilfs_segctor_collect_blocks fs/nilfs2/segment.c:1197 [inline]
  nilfs_segctor_collect fs/nilfs2/segment.c:1503 [inline]
  nilfs_segctor_do_construct+0x12fc/0x6af0 fs/nilfs2/segment.c:2045
  nilfs_segctor_construct+0x8e3/0xb30 fs/nilfs2/segment.c:2379
  nilfs_segctor_thread_construct fs/nilfs2/segment.c:2487 [inline]
  nilfs_segctor_thread+0x3c3/0xf30 fs/nilfs2/segment.c:2570
  kthread+0x2e4/0x3a0 kernel/kthread.c:376
  ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
  </TASK>
...

If DAT metadata file is corrupted on disk, there is a case where
req->pr_desc_bh is NULL and blocknr is 0 at nilfs_dat_commit_end() during
a b-tree operation that cascadingly updates ancestor nodes of the b-tree,
because nilfs_dat_commit_alloc() for a lower level block can initialize
the blocknr on the same DAT entry between nilfs_dat_prepare_end() and
nilfs_dat_commit_end().

If this happens, nilfs_dat_commit_end() calls nilfs_dat_commit_free()
without valid buffer heads in req->pr_desc_bh and req->pr_bitmap_bh, and
causes the NULL pointer dereference above in
nilfs_palloc_commit_free_entry() function, which leads to a crash.

Fix this by adding a NULL check on req->pr_desc_bh and req->pr_bitmap_bh
before nilfs_palloc_commit_free_entry() in nilfs_dat_commit_free().

This also calls nilfs_error() in that case to notify that there is a fatal
flaw in the filesystem metadata and prevent further operations.

Link: https://lkml.kernel.org/r/00000000000097c20205ebaea3d6@google.com
Link: https://lkml.kernel.org/r/20221114040441.1649940-1-zhangpeng362@huawei.com
Link: https://lkml.kernel.org/r/20221119120542.17204-1-konishi.ryusuke@gmail.com
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+ebe05ee8e98f755f61d0@syzkaller.appspotmail.com
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools/vm/slabinfo-gnuplot: use "grep -E" instead of "egrep"

commit a435874bf626f55d7147026b059008c8de89fbb8 upstream.

The latest version of grep claims the egrep is now obsolete so the build
now contains warnings that look like:

egrep: warning: egrep is obsolescent; using grep -E

fix this up by moving the related file to use "grep -E" instead.

  sed -i "s/egrep/grep -E/g" `grep egrep -rwl tools/vm`

Here are the steps to install the latest grep:

  wget http://ftp.gnu.org/gnu/grep/grep-3.8.tar.gz
  tar xf grep-3.8.tar.gz
  cd grep-3.8 && ./configure && make
  sudo make install
  export PATH=/usr/local/bin:$PATH

Link: https://lkml.kernel.org/r/1668825419-30584-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

error-injection: Add prompt for function error injection

commit a4412fdd49dc011bcc2c0d81ac4cab7457092650 upstream.

The config to be able to inject error codes into any function annotated
with ALLOW_ERROR_INJECTION() is enabled when FUNCTION_ERROR_INJECTION is
enabled.  But unfortunately, this is always enabled on x86 when KPROBES
is enabled, and there's no way to turn it off.

As kprobes is useful for observability of the kernel, it is useful to
have it enabled in production environments.  But error injection should
be avoided.  Add a prompt to the config to allow it to be disabled even
when kprobes is enabled, and get rid of the "def_bool y".

This is a kernel debug feature (it's in Kconfig.debug), and should have
never been something enabled by default.

Cc: stable@vger.kernel.org
Fixes: 540adea3809f6 ("error-injection: Separate error-injection from kprobe")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

riscv: vdso: fix section overlapping under some conditions

commit 74f6bb55c834da6d4bac24f44868202743189b2b upstream.

lkp reported a build error, I tried the config and can reproduce
build error as below:

VDSOLD arch/riscv/kernel/vdso/vdso.so.dbg
ld.lld: error: section .note file range overlaps with .text
>>> .note range is [0x7C8, 0x803]
>>> .text range is [0x800, 0x1993]

ld.lld: error: section .text file range overlaps with .dynamic
>>> .text range is [0x800, 0x1993]
>>> .dynamic range is [0x808, 0x937]

ld.lld: error: section .note virtual address range overlaps with .text
>>> .note range is [0x7C8, 0x803]
>>> .text range is [0x800, 0x1993]

Fix it by setting DISABLE_BRANCH_PROFILING which will disable branch
tracing for vdso, thus avoid useless _ftrace_annotated_branch section
and _ftrace_branch section. Although we can also fix it by removing
the hardcoded .text begin address, but I think that's another story
and should be put into another patch.

Link: https://lore.kernel.org/lkml/202210122123.Cc4FPShJ-lkp@intel.com/#r
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221102170254.1925-1-jszhang@kernel.org
Fixes: ad5d1122b82f ("riscv: use vDSO common flow to reduce the latency of the time-related functions")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: DR, Fix uninitialized var warning

[ Upstream commit 52f7cf70eb8fac6111786c59ae9dfc5cf2bee710 ]

Smatch warns this:

drivers/net/ethernet/mellanox/mlx5/core/steering/dr_table.c:81
mlx5dr_table_set_miss_action() error: uninitialized symbol 'ret'.

Initializing ret with -EOPNOTSUPP and fix missing action case.

Fixes: 7838e1725394 ("net/mlx5: DR, Expose steering table functionality")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (coretemp) fix pci device refcount leak in nv1a_ram_new()

[ Upstream commit 7dec14537c5906b8bf40fd6fd6d9c3850f8df11d ]

As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). So call it after using to avoid refcount leak.

Fixes: 14513ee696a0 ("hwmon: (coretemp) Use PCI host bridge ID to identify CPU if necessary")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221118093303.214163-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (coretemp) Check for null before removing sysfs attrs

[ Upstream commit a89ff5f5cc64b9fe7a992cf56988fd36f56ca82a ]

If coretemp_add_core() gets an error then pdata->core_data[indx]
is already NULL and has been kfreed. Don't pass that to
sysfs_remove_group() as that will crash in sysfs_remove_group().

[Shortened for readability]
[91854.020159] sysfs: cannot create duplicate filename '/devices/platform/coretemp.0/hwmon/hwmon2/temp20_label'
<cpu offline>
[91855.126115] BUG: kernel NULL pointer dereference, address: 0000000000000188
[91855.165103] #PF: supervisor read access in kernel mode
[91855.194506] #PF: error_code(0x0000) - not-present page
[91855.224445] PGD 0 P4D 0
[91855.238508] Oops: 0000 [#1] PREEMPT SMP PTI
...
[91855.342716] RIP: 0010:sysfs_remove_group+0xc/0x80
...
[91855.796571] Call Trace:
[91855.810524]  coretemp_cpu_offline+0x12b/0x1dd [coretemp]
[91855.841738]  ? coretemp_cpu_online+0x180/0x180 [coretemp]
[91855.871107]  cpuhp_invoke_callback+0x105/0x4b0
[91855.893432]  cpuhp_thread_fun+0x8e/0x150
...

Fix this by checking for NULL first.

Signed-off-by: Phil Auld <pauld@redhat.com>
Cc: linux-hwmon@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20221117162313.3164803-1-pauld@redhat.com
Fixes: 199e0de7f5df3 ("hwmon: (coretemp) Merge pkgtemp with coretemp")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ethernet: renesas: ravb: Fix promiscuous mode after system resumed

[ Upstream commit d66233a312ec9013af3e37e4030b479a20811ec3 ]

After system resumed on some environment board, the promiscuous mode
is disabled because the SoC turned off. So, call ravb_set_rx_mode() in
the ravb_resume() to fix the issue.

Reported-by: Tho Vu <tho.vu.wh@renesas.com>
Fixes: 0184165b2f42 ("ravb: add sleep PM suspend/resume support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20221128065604.1864391-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sctp: fix memory leak in sctp_stream_outq_migrate()

[ Upstream commit 9ed7bfc79542119ac0a9e1ce8a2a5285e43433e9 ]

When sctp_stream_outq_migrate() is called to release stream out resources,
the memory pointed to by prio_head in stream out is not released.

The memory leak information is as follows:
unreferenced object 0xffff88801fe79f80 (size 64):
   comm "sctp_repo", pid 7957, jiffies 4294951704 (age 36.480s)
   hex dump (first 32 bytes):
     80 9f e7 1f 80 88 ff ff 80 9f e7 1f 80 88 ff ff  ................
     90 9f e7 1f 80 88 ff ff 90 9f e7 1f 80 88 ff ff  ................
   backtrace:
     [<ffffffff81b215c6>] kmalloc_trace+0x26/0x60
     [<ffffffff88ae517c>] sctp_sched_prio_set+0x4cc/0x770
     [<ffffffff88ad64f2>] sctp_stream_init_ext+0xd2/0x1b0
     [<ffffffff88aa2604>] sctp_sendmsg_to_asoc+0x1614/0x1a30
     [<ffffffff88ab7ff1>] sctp_sendmsg+0xda1/0x1ef0
     [<ffffffff87f765ed>] inet_sendmsg+0x9d/0xe0
     [<ffffffff8754b5b3>] sock_sendmsg+0xd3/0x120
     [<ffffffff8755446a>] __sys_sendto+0x23a/0x340
     [<ffffffff87554651>] __x64_sys_sendto+0xe1/0x1b0
     [<ffffffff89978b49>] do_syscall_64+0x39/0xb0
     [<ffffffff89a0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

Link: https://syzkaller.appspot.com/bug?exrid=29c402e56c4760763cc0
Fixes: 637784ade221 ("sctp: introduce priority based stream scheduler")
Reported-by: syzbot+29c402e56c4760763cc0@syzkaller.appspotmail.com
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/20221126031720.378562-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

packet: do not set TP_STATUS_CSUM_VALID on CHECKSUM_COMPLETE

[ Upstream commit b85f628aa158a653c006e9c1405a117baef8c868 ]

CHECKSUM_COMPLETE signals that skb->csum stores the sum over the
entire packet. It does not imply that an embedded l4 checksum
field has been validated.

Fixes: 682f048bd494 ("af_packet: pass checksum validation status to the user")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20221128161812.640098-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: tun: Fix use-after-free in tun_detach()

[ Upstream commit 5daadc86f27ea4d691e2131c04310d0418c6cd12 ]

syzbot reported use-after-free in tun_detach() [1]. This causes call
trace like below:

==================================================================
BUG: KASAN: use-after-free in notifier_call_chain+0x1ee/0x200 kernel/notifier.c:75
Read of size 8 at addr ffff88807324e2a8 by task syz-executor.0/3673

CPU: 0 PID: 3673 Comm: syz-executor.0 Not tainted 6.1.0-rc5-syzkaller-00044-gcc675d22e422 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd1/0x138 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x15e/0x461 mm/kasan/report.c:395
kasan_report+0xbf/0x1f0 mm/kasan/report.c:495
notifier_call_chain+0x1ee/0x200 kernel/notifier.c:75
call_netdevice_notifiers_info+0x86/0x130 net/core/dev.c:1942
call_netdevice_notifiers_extack net/core/dev.c:1983 [inline]
call_netdevice_notifiers net/core/dev.c:1997 [inline]
netdev_wait_allrefs_any net/core/dev.c:10237 [inline]
netdev_run_todo+0xbc6/0x1100 net/core/dev.c:10351
tun_detach drivers/net/tun.c:704 [inline]
tun_chr_close+0xe4/0x190 drivers/net/tun.c:3467
__fput+0x27c/0xa90 fs/file_table.c:320
task_work_run+0x16f/0x270 kernel/task_work.c:179
exit_task_work include/linux/task_work.h:38 [inline]
do_exit+0xb3d/0x2a30 kernel/exit.c:820
do_group_exit+0xd4/0x2a0 kernel/exit.c:950
get_signal+0x21b1/0x2440 kernel/signal.c:2858
arch_do_signal_or_restart+0x86/0x2300 arch/x86/kernel/signal.c:869
exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
__syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
do_syscall_64+0x46/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd

The cause of the issue is that sock_put() from __tun_detach() drops
last reference count for struct net, and then notifier_call_chain()
from netdev_state_change() accesses that struct net.

This patch fixes the issue by calling sock_put() from tun_detach()
after all necessary accesses for the struct net has done.

Fixes: 83c1f36f9880 ("tun: send netlink notification when the device is modified")
Reported-by: syzbot+106f9b687cd64ee70cd1@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=96eb7f1ce75ef933697f24eeab928c4a716edefe
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20221124175134.1589053-1-syoshida@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

afs: Fix fileserver probe RTT handling

[ Upstream commit ca57f02295f188d6c65ec02202402979880fa6d8 ]

The fileserver probing code attempts to work out the best fileserver to
use for a volume by retrieving the RTT calculated by AF_RXRPC for the
probe call sent to each server and comparing them. Sometimes, however,
no RTT estimate is available and rxrpc_kernel_get_srtt() returns false,
leading good fileservers to be given an RTT of UINT_MAX and thus causing
the rotation algorithm to ignore them.

Fix afs_select_fileserver() to ignore rxrpc_kernel_get_srtt()'s return
value and just take the estimated RTT it provides - which will be capped
at 1 second.

Fixes: 1d4adfaf6574 ("rxrpc: Make rxrpc_kernel_get_srtt() indicate validity")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/166965503999.3392585.13954054113218099395.stgit@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hsr: Fix potential use-after-free

[ Upstream commit 7e177d32442b7ed08a9fa61b61724abc548cb248 ]

The skb is delivered to netif_rx() which may free it, after calling this,
dereferencing skb may trigger use-after-free.

Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20221125075724.27912-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tipc: re-fetch skb cb after tipc_msg_validate

[ Upstream commit 3067bc61fcfe3081bf4807ce65560f499e895e77 ]

As the call trace shows, the original skb was freed in tipc_msg_validate(),
and dereferencing the old skb cb would cause an use-after-free crash.

  BUG: KASAN: use-after-free in tipc_crypto_rcv_complete+0x1835/0x2240 [tipc]
  Call Trace:
   <IRQ>
   tipc_crypto_rcv_complete+0x1835/0x2240 [tipc]
   tipc_crypto_rcv+0xd32/0x1ec0 [tipc]
   tipc_rcv+0x744/0x1150 [tipc]
  ...
  Allocated by task 47078:
   kmem_cache_alloc_node+0x158/0x4d0
   __alloc_skb+0x1c1/0x270
   tipc_buf_acquire+0x1e/0xe0 [tipc]
   tipc_msg_create+0x33/0x1c0 [tipc]
   tipc_link_build_proto_msg+0x38a/0x2100 [tipc]
   tipc_link_timeout+0x8b8/0xef0 [tipc]
   tipc_node_timeout+0x2a1/0x960 [tipc]
   call_timer_fn+0x2d/0x1c0
  ...
  Freed by task 47078:
   tipc_msg_validate+0x7b/0x440 [tipc]
   tipc_crypto_rcv_complete+0x4b5/0x2240 [tipc]
   tipc_crypto_rcv+0xd32/0x1ec0 [tipc]
   tipc_rcv+0x744/0x1150 [tipc]

This patch fixes it by re-fetching the skb cb from the new allocated skb
after calling tipc_msg_validate().

Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1b1cdba762915325bd8ef9a98d0276eb673df2a5.1669398403.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dsa: lan9303: Correct stat name

[ Upstream commit 39f59bca275d2d819a8788c0f962e9e89843efc9 ]

This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.

The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.

Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ethernet: nixge: fix NULL dereference

[ Upstream commit 9256db4e45e8b497b0e993cc3ed4ad08eb2389b6 ]

In function nixge_hw_dma_bd_release() dereference of NULL pointer
priv->rx_bd_v is possible for the case of its allocation failure in
nixge_hw_dma_bd_init().

Move for() loop with priv->rx_bd_v dereference under the check for
its validity.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 492caffa8a1a ("net: ethernet: nixge: Add support for National Instruments XGE netdev")
Signed-off-by: Yuri Karpov <YKarpov@ispras.ru>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/9p: Fix a potential socket leak in p9_socket_open

[ Upstream commit dcc14cfd7debe11b825cb077e75d91d2575b4cb8 ]

Both p9_fd_create_tcp() and p9_fd_create_unix() will call
p9_socket_open(). If the creation of p9_trans_fd fails,
p9_fd_create_tcp() and p9_fd_create_unix() will return an
error directly instead of releasing the cscoket, which will
result in a socket leak.

This patch adds sock_release() to fix the leak issue.

Fixes: 6b18662e239a ("9p connect fixes")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
ACKed-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: net_netdev: Fix error handling in ntb_netdev_init_module()

[ Upstream commit b8f79dccd38edf7db4911c353d9cd792ab13a327 ]

The ntb_netdev_init_module() returns the ntb_transport_register_client()
directly without checking its return value, if
ntb_transport_register_client() failed, the NTB client device is not
unregistered.

Fix by unregister NTB client device when ntb_transport_register_client()
failed.

Fixes: 548c237c0a99 ("net: Add support for NTB virtual ethernet device")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: fix null-ptr-deref while probe() failed

[ Upstream commit 369eb2c9f1f72adbe91e0ea8efb130f0a2ba11a6 ]

I got a null-ptr-deref report as following when doing fault injection test:

BUG: kernel NULL pointer dereference, address: 0000000000000058
Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 PID: 253 Comm: 507-spi-dm9051 Tainted: G    B            N 6.1.0-rc3+
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:klist_put+0x2d/0xd0
Call Trace:
<TASK>
klist_remove+0xf1/0x1c0
device_release_driver_internal+0x23e/0x2d0
bus_remove_device+0x1bd/0x240
device_del+0x357/0x770
phy_device_remove+0x11/0x30
mdiobus_unregister+0xa5/0x140
release_nodes+0x6a/0xa0
devres_release_all+0xf8/0x150
device_unbind_cleanup+0x19/0xd0

//probe path:
phy_device_register()
  device_add()

phy_connect
  phy_attach_direct() //set device driver
    probe() //it's failed, driver is not bound
    device_bind_driver() // probe failed, it's not called

//remove path:
phy_device_remove()
  device_del()
    device_release_driver_internal()
      __device_release_driver() //dev->drv is not NULL
        klist_remove() <- knode_driver is not added yet, cause null-ptr-deref

In phy_attach_direct(), after setting the 'dev->driver', probe() fails,
device_bind_driver() is not called, so the knode_driver->n_klist is not
set, then it causes null-ptr-deref in __device_release_driver() while
deleting device. Fix this by setting dev->driver to NULL in the error
path in phy_attach_direct().

Fixes: e13934563db0 ("[PATCH] PHY Layer fixup")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: mac8021: fix possible oob access in ieee80211_get_rate_duration

[ Upstream commit 3e8f7abcc3473bc9603323803aeaed4ffcc3a2ab ]

Fix possible out-of-bound access in ieee80211_get_rate_duration routine
as reported by the following UBSAN report:

UBSAN: array-index-out-of-bounds in net/mac80211/airtime.c:455:47
index 15 is out of range for type 'u16 [12]'
CPU: 2 PID: 217 Comm: kworker/u32:10 Not tainted 6.1.0-060100rc3-generic
Hardware name: Acer Aspire TC-281/Aspire TC-281, BIOS R01-A2 07/18/2017
Workqueue: mt76 mt76u_tx_status_data [mt76_usb]
Call Trace:
<TASK>
show_stack+0x4e/0x61
dump_stack_lvl+0x4a/0x6f
dump_stack+0x10/0x18
ubsan_epilogue+0x9/0x43
__ubsan_handle_out_of_bounds.cold+0x42/0x47
ieee80211_get_rate_duration.constprop.0+0x22f/0x2a0 [mac80211]
? ieee80211_tx_status_ext+0x32e/0x640 [mac80211]
ieee80211_calc_rx_airtime+0xda/0x120 [mac80211]
ieee80211_calc_tx_airtime+0xb4/0x100 [mac80211]
mt76x02_send_tx_status+0x266/0x480 [mt76x02_lib]
mt76x02_tx_status_data+0x52/0x80 [mt76x02_lib]
mt76u_tx_status_data+0x67/0xd0 [mt76_usb]
process_one_work+0x225/0x400
worker_thread+0x50/0x3e0
? process_one_work+0x400/0x400
kthread+0xe9/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30

Fixes: db3e1c40cf2f ("mac80211: Import airtime calculation code from mt76")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: cfg80211: don't allow multi-BSSID in S1G

[ Upstream commit acd3c92acc7aaec50a94d0a7faf7ccd74e952493 ]

In S1G beacon frames there shouldn't be multi-BSSID elements
since that's not supported, remove that to avoid a potential
integer underflow and/or misparsing the frames due to the
different length of the fixed part of the frame.

While at it, initialize non_tx_data so we don't send garbage
values to the user (even if it doesn't seem to matter now.)

Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaffe5078ca ("cfg80211: convert S1G beacon to scan results")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: cfg80211: fix buffer overflow in elem comparison

[ Upstream commit 9f16b5c82a025cd4c864737409234ddc44fb166a ]

For vendor elements, the code here assumes that 5 octets
are present without checking. Since the element itself is
already checked to fit, we only need to check the length.

Reported-and-tested-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 0b8fb8235be8 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

aquantia: Do not purge addresses when setting the number of rings

[ Upstream commit 2a83891130512dafb321418a8e7c9c09268d8c59 ]

IPV6 addresses are purged when setting the number of rx/tx
rings using ethtool -G. The function aq_set_ringparam
calls dev_close, which removes the addresses. As a solution,
call an internal function (aq_ndev_close).

Fixes: c1af5427954b ("net: aquantia: Ethtool based ring size configuration")
Signed-off-by: Izabela Bakollari <ibakolla@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qlcnic: fix sleep-in-atomic-context bugs caused by msleep

[ Upstream commit 8dbd6e4ce1b9c527921643d9e34f188a10d4e893 ]

The watchdog timer is used to monitor whether the process
of transmitting data is timeout. If we use qlcnic driver,
the dev_watchdog() that is the timer handler of watchdog
timer will call qlcnic_tx_timeout() to process the timeout.
But the qlcnic_tx_timeout() calls msleep(), as a result,
the sleep-in-atomic-context bugs will happen. The processes
are shown below:

   (atomic context)
dev_watchdog
  qlcnic_tx_timeout
    qlcnic_83xx_idc_request_reset
      qlcnic_83xx_lock_driver
        msleep

---------------------------

   (atomic context)
dev_watchdog
  qlcnic_tx_timeout
    qlcnic_83xx_idc_request_reset
      qlcnic_83xx_lock_driver
        qlcnic_83xx_recover_driver_lock
          msleep

Fix by changing msleep() to mdelay(), the mdelay() is
busy-waiting and the bugs could be mitigated.

Fixes: 629263acaea3 ("qlcnic: 83xx CNA inter driver communication mechanism")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: cc770: cc770_isa_probe(): add missing free_cc770dev()

[ Upstream commit 62ec89e74099a3d6995988ed9f2f996b368417ec ]

Add the missing free_cc770dev() before return from cc770_isa_probe()
in the register_cc770dev() error handling case.

In addition, remove blanks before goto labels.

Fixes: 7e02e5433e00 ("can: cc770: legacy CC770 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168557-6024-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: sja1000_isa: sja1000_isa_probe(): add missing free_sja1000dev()

[ Upstream commit 92dfd9310a71d28cefe6a2d5174d43fab240e631 ]

Add the missing free_sja1000dev() before return from
sja1000_isa_probe() in the register_sja1000dev() error handling case.

In addition, remove blanks before goto labels.

Fixes: 2a6ba39ad6a2 ("can: sja1000: legacy SJA1000 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168521-5540-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Fix use-after-free when reverting termination table

[ Upstream commit 52c795af04441d76f565c4634f893e5b553df2ae ]

When having multiple dests with termination tables and second one
or afterwards fails the driver reverts usage of term tables but
doesn't reset the assignment in attr->dests[num_vport_dests].termtbl
which case a use-after-free when releasing the rule.
Fix by resetting the assignment of termtbl to null.

Fixes: 10caabdaad5a ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: Fix uninitialized variable bug in outlen_write()

[ Upstream commit 3f5769a074c13d8f08455e40586600419e02a880 ]

If sscanf() return 0, outlen is uninitialized and used in kzalloc(),
this is unexpected. We should return -EINVAL if the string is invalid.

Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

e100: Fix possible use after free in e100_xmit_prepare

[ Upstream commit 45605c75c52c7ae7bfe902214343aabcfe5ba0ff ]

In e100_xmit_prepare(), if we can't map the skb, then return -ENOMEM, so
e100_xmit_frame() will return NETDEV_TX_BUSY and the upper layer will
resend the skb. But the skb is already freed, which will cause UAF bug
when the upper layer resends the skb.

Remove the harmful free.

Fixes: 5e5d49422dfb ("e100: Release skb when DMA mapping is failed in e100_xmit_prepare")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

e100: switch from 'pci_' to 'dma_' API

[ Upstream commit 4140ff1ba06d3fc16afd518736940ab742886317 ]

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'e100_alloc()', GFP_KERNEL can be used because
it is only called from the probe function and no lock is acquired.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Link: https://lore.kernel.org/r/20210128210736.749724-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 45605c75c52c ("e100: Fix possible use after free in e100_xmit_prepare")
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: Fix error handling in iavf_init_module()

[ Upstream commit 227d8d2f7f2278b8468c5531b0cd0f2a905b4486 ]

The iavf_init_module() won't destroy workqueue when pci_register_driver()
failed. Call destroy_workqueue() when pci_register_driver() failed to
prevent the resource leak.

Similar to the handling of u132_hcd_init in commit f276e002793c
("usb: u132-hcd: fix resource leak")

Fixes: 2803b16c10ea ("i40e/i40evf: Use private workqueue")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: remove redundant ret variable

[ Upstream commit c3fec56e12678c3ad68084048a73818a7968d6b8 ]

Return value directly instead of taking this in another redundant
variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: CGEL ZTE <cgel.zte@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 227d8d2f7f22 ("iavf: Fix error handling in iavf_init_module()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

fm10k: Fix error handling in fm10k_init_module()

[ Upstream commit 771a794c0a3c3e7f0d86cc34be4f9537e8c0a20c ]

A problem about modprobe fm10k failed is triggered with the following log
given:

Intel(R) Ethernet Switch Host Interface Driver
Copyright(c) 2013 - 2019 Intel Corporation.
debugfs: Directory 'fm10k' with parent '/' already present!

The reason is that fm10k_init_module() returns fm10k_register_pci_driver()
directly without checking its return value, if fm10k_register_pci_driver()
failed, it returns without removing debugfs and destroy workqueue,
resulting the debugfs of fm10k can never be created later and leaks the
workqueue.

fm10k_init_module()
   alloc_workqueue()
   fm10k_dbg_init() # create debugfs
   fm10k_register_pci_driver()
     pci_register_driver()
       driver_register()
         bus_add_driver()
           priv = kzalloc(...) # OOM happened
   # return without remove debugfs and destroy workqueue

Fix by remove debugfs and destroy workqueue when
fm10k_register_pci_driver() returns error.

Fixes: 7461fd913afe ("fm10k: Add support for debugfs")
Fixes: b382bb1b3e2d ("fm10k: use separate workqueue for fm10k driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Fix error handling in i40e_init_module()

[ Upstream commit 479dd06149425b9e00477f52200872587af76a48 ]

i40e_init_module() won't free the debugfs directory created by
i40e_dbg_init() when pci_register_driver() failed. Add fail path to
call i40e_dbg_exit() to remove the debugfs entries to prevent the bug.

i40e: Intel(R) Ethernet Connection XL710 Network Driver
i40e: Copyright (c) 2013 - 2019 Intel Corporation.
debugfs: Directory 'i40e' with parent '/' already present!

Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ixgbevf: Fix resource leak in ixgbevf_init_module()

[ Upstream commit 8cfa238a48f34038464b99d0b4825238c2687181 ]

ixgbevf_init_module() won't destroy the workqueue created by
create_singlethread_workqueue() when pci_register_driver() failed. Add
destroy_workqueue() in fail path to prevent the resource leak.

Similar to the handling of u132_hcd_init in commit f276e002793c
("usb: u132-hcd: fix resource leak")

Fixes: 40a13e2493c9 ("ixgbevf: Use a private workqueue to avoid certain possible hangs")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: property: decrement node refcount in of_fwnode_get_reference_args()

[ Upstream commit 60d865bd5a9b15a3961eb1c08bd4155682a3c81e ]

In of_fwnode_get_reference_args(), the refcount of of_args.np has
been incremented in the case of successful return from
of_parse_phandle_with_args() or of_parse_phandle_with_fixed_args().

Decrement the refcount if of_args is not returned to the caller of
of_fwnode_get_reference_args().

Fixes: 3e3119d3088f ("device property: Introduce fwnode_property_get_reference_args")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Link: https://lore.kernel.org/r/20221121023209.3909759-1-yangyingliang@huawei.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Do not copy spin lock field from user in bpf_selem_alloc

[ Upstream commit 836e49e103dfeeff670c934b7d563cbd982fce87 ]

bpf_selem_alloc function is used by inode_storage, sk_storage and
task_storage maps to set map value, for these map types, there may
be a spin lock in the map value, so if we use memcpy to copy the whole
map value from user, the spin lock field may be initialized incorrectly.

Since the spin lock field is zeroed by kzalloc, call copy_map_value
instead of memcpy to skip copying the spin lock field to fix it.

Fixes: 6ac99e8f23d4 ("bpf: Introduce bpf sk local storage")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Link: https://lore.kernel.org/r/20221114134720.1057939-2-xukuohai@huawei.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (ibmpex) Fix possible UAF when ibmpex_register_bmc() fails

[ Upstream commit e2a87785aab0dac190ac89be6a9ba955e2c634f2 ]

Smatch report warning as follows:

drivers/hwmon/ibmpex.c:509 ibmpex_register_bmc() warn:
'&data->list' not removed from list

If ibmpex_find_sensors() fails in ibmpex_register_bmc(), data will
be freed, but data->list will not be removed from driver_data.bmc_data,
then list traversal may cause UAF.

Fix by removeing it from driver_data.bmc_data before free().

Fixes: 57c7c3a0fdea ("hwmon: IBM power meter driver")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221117034423.2935739-1-cuigaosheng1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (i5500_temp) fix missing pci_disable_device()

[ Upstream commit 3b7f98f237528c496ea0b689bace0e35eec3e060 ]

pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release().

Fixes: ada072816be1 ("hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221112125606.3751430-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (ina3221) Fix shunt sum critical calculation

[ Upstream commit b8d27d2ce8dfc207e4b67b929a86f2be76fbc6ef ]

The shunt sum critical limit register value should be left shifted
by one bit as its LSB-0 is a reserved bit.

Fixes: 2057bdfb7184 ("hwmon: (ina3221) Add summation feature support")
Signed-off-by: Ninad Malwade <nmalwade@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221108044508.23463-1-nmalwade@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (ltc2947) fix temperature scaling

[ Upstream commit 07e06193ead86d4812f431b4d87bbd4161222e3f ]

The LTC2947 datasheet (Rev. B) calls out in the section "Register
Description: Non-Accumulated Result Registers" (pg. 30) that "To
calculate temperature, multiply the TEMP register value by 0.204°C
and add 5.5°C". Fix to add 5.5C and not 0.55C.

Fixes: 9f90fd652bed ("hwmon: Add support for ltc2947")
Signed-off-by: Derek Nguyen <derek.nguyen@collins.com>
Signed-off-by: Brandon Maier <brandon.maier@collins.com>
Link: https://lore.kernel.org/r/20221110192108.20624-1-brandon.maier@collins.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

libbpf: Handle size overflow for ringbuf mmap

[ Upstream commit 927cbb478adf917e0a142b94baa37f06279cc466 ]

The maximum size of ringbuf is 2GB on x86-64 host, so 2 * max_entries
will overflow u32 when mapping producer page and data pages. Only
casting max_entries to size_t is not enough, because for 32-bits
application on 64-bits kernel the size of read-only mmap region
also could overflow size_t.

So fixing it by casting the size of read-only mmap region into a __u64
and checking whether or not there will be overflow during mmap.

Fixes: bf99c936f947 ("libbpf: Add BPF ring buffer support")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20221116072351.1168938-3-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: at91: rm9200: fix usb device clock id

[ Upstream commit 57976762428675f259339385d3324d28ee53ec02 ]

Referring to the datasheet the index 2 is the MCKUDP. When enabled, it
"Enables the automatic disable of the Master Clock of the USB Device
Port when a suspend condition occurs". We fix the index to the real UDP
id which "Enables the 48 MHz clock of the USB Device Port".

Cc: nicolas.ferre@microchip.com
Cc: ludovic.desroches@microchip.com
Cc: alexandre.belloni@bootlin.com
Cc: mturquette@baylibre.com
Cc: sboyd@kernel.org
Cc: claudiu.beznea@microchip.com
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@pengutronix.de
Fixes: 02ff48e4d7f7 ("clk: at91: add at91rm9200 pmc driver")
Fixes: 0e0e528d8260 ("ARM: dts: at91: rm9200: switch to new clock bindings")
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221114185923.1023249-2-m.grzeschik@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

scripts/faddr2line: Fix regression in name resolution on ppc64le

[ Upstream commit 2d77de1581bb5b470486edaf17a7d70151131afd ]

Commit 1d1a0e7c5100 ("scripts/faddr2line: Fix overlapping text section
failures") can cause faddr2line to fail on ppc64le on some
distributions, while it works fine on other distributions. The failure
can be attributed to differences in the readelf output.

  $ ./scripts/faddr2line vmlinux find_busiest_group+0x00
  no match for find_busiest_group+0x00

On ppc64le, readelf adds the localentry tag before the symbol name on
some distributions, and adds the localentry tag after the symbol name on
other distributions. This problem has been discussed previously:

  https://lore.kernel.org/bpf/20191211160133.GB4580@calabresa/

This problem can be overcome by filtering out the localentry tags in the
readelf output. Similar fixes are already present in the kernel by way
of the following commits:

  1fd6cee127e2 ("libbpf: Fix VERSIONED_SYM_COUNT number parsing")
  aa915931ac3e ("libbpf: Fix readelf output parsing for Fedora")

[jpoimboe: rework commit log]

Fixes: 1d1a0e7c5100 ("scripts/faddr2line: Fix overlapping text section failures")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Link: https://lore.kernel.org/r/20220927075211.897152-1-srikar@linux.vnet.ibm.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, perf: Use subprog name when reporting subprog ksymbol

[ Upstream commit 47df8a2f78bc34ff170d147d05b121f84e252b85 ]

Since commit bfea9a8574f3 ("bpf: Add name to struct bpf_ksym"), when
reporting subprog ksymbol to perf, prog name instead of subprog name is
used. The backtrace of bpf program with subprogs will be incorrect as
shown below:

  ffffffffc02deace bpf_prog_e44a3057dcb151f8_overwrite+0x66
  ffffffffc02de9f7 bpf_prog_e44a3057dcb151f8_overwrite+0x9f
  ffffffffa71d8d4e trace_call_bpf+0xce
  ffffffffa71c2938 perf_call_bpf_enter.isra.0+0x48

overwrite is the entry program and it invokes the overwrite_htab subprog
through bpf_loop, but in above backtrace, overwrite program just jumps
inside itself.

Fixing it by using subprog name when reporting subprog ksymbol. After
the fix, the output of perf script will be correct as shown below:

  ffffffffc031aad2 bpf_prog_37c0bec7d7c764a4_overwrite_htab+0x66
  ffffffffc031a9e7 bpf_prog_c7eb827ef4f23e71_overwrite+0x9f
  ffffffffa3dd8d4e trace_call_bpf+0xce
  ffffffffa3dc2938 perf_call_bpf_enter.isra.0+0x48

Fixes: bfea9a8574f3 ("bpf: Add name to struct bpf_ksym")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20221114095733.158588-1-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: light: rpr0521: add missing Kconfig dependencies

[ Upstream commit 6ac12303572ef9ace5603c2c07f5f1b00a33f580 ]

Fix an implicit declaration of function error for rpr0521 under some configs

When CONFIG_RPR0521 is enabled without CONFIG_IIO_TRIGGERED_BUFFER,
the build results in "implicit declaration of function" errors, e.g.,
  drivers/iio/light/rpr0521.c:434:3: error: implicit declaration of function
           'iio_trigger_poll_chained' [-Werror=implicit-function-declaration]
    434 |   iio_trigger_poll_chained(data->drdy_trigger0);
        |   ^~~~~~~~~~~~~~~~~~~~~~~~

This fix adds select dependencies to RPR0521's configuration declaration.

Fixes: e12ffd241c00 ("iio: light: rpr0521 triggered buffer")
Signed-off-by: Paul Gazzillo <paul@pgazz.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216678
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221110214729.ls5ixav5kxpeftk7@device
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: health: afe4404: Fix oob read in afe4404_[read|write]_raw

[ Upstream commit fc92d9e3de0b2d30a3ccc08048a5fad533e4672b ]

KASAN report out-of-bounds read as follows:

BUG: KASAN: global-out-of-bounds in afe4404_read_raw+0x2ce/0x380
Read of size 4 at addr ffffffffc00e4658 by task cat/278

Call Trace:
afe4404_read_raw
iio_read_channel_info
dev_attr_show

The buggy address belongs to the variable:
afe4404_channel_leds+0x18/0xffffffffffffe9c0

This issue can be reproduce by singe command:

$ cat /sys/bus/i2c/devices/0-0058/iio\:device0/in_intensity6_raw

The array size of afe4404_channel_leds and afe4404_channel_offdacs
are less than channels, so access with chan->address cause OOB read
in afe4404_[read|write]_raw. Fix it by moving access before use them.

Fixes: b36e8257641a ("iio: health/afe440x: Use regmap fields")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20221107152010.95937-1-weiyongjun@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: health: afe4403: Fix oob read in afe4403_read_raw

[ Upstream commit 58143c1ed5882c138a3cd2251a336fc8755f23d9 ]

KASAN report out-of-bounds read as follows:

BUG: KASAN: global-out-of-bounds in afe4403_read_raw+0x42e/0x4c0
Read of size 4 at addr ffffffffc02ac638 by task cat/279

Call Trace:
afe4403_read_raw
iio_read_channel_info
dev_attr_show

The buggy address belongs to the variable:
afe4403_channel_leds+0x18/0xffffffffffffe9e0

This issue can be reproduced by singe command:

$ cat /sys/bus/spi/devices/spi0.0/iio\:device0/in_intensity6_raw

The array size of afe4403_channel_leds is less than channels, so access
with chan->address cause OOB read in afe4403_read_raw. Fix it by moving
access before use it.

Fixes: b36e8257641a ("iio: health/afe440x: Use regmap fields")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20221107151946.89260-1-weiyongjun@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: qgroup: fix sleep from invalid context bug in btrfs_qgroup_inherit()

[ Upstream commit f7e942b5bb35d8e3af54053d19a6bf04143a3955 ]

Syzkaller reported BUG as follows:

  BUG: sleeping function called from invalid context at
       include/linux/sched/mm.h:274
  Call Trace:
   <TASK>
   dump_stack_lvl+0xcd/0x134
   __might_resched.cold+0x222/0x26b
   kmem_cache_alloc+0x2e7/0x3c0
   update_qgroup_limit_item+0xe1/0x390
   btrfs_qgroup_inherit+0x147b/0x1ee0
   create_subvol+0x4eb/0x1710
   btrfs_mksubvol+0xfe5/0x13f0
   __btrfs_ioctl_snap_create+0x2b0/0x430
   btrfs_ioctl_snap_create_v2+0x25a/0x520
   btrfs_ioctl+0x2a1c/0x5ce0
   __x64_sys_ioctl+0x193/0x200
   do_syscall_64+0x35/0x80

Fix this by calling qgroup_dirty() on @dstqgroup, and update limit item in
btrfs_run_qgroups() later outside of the spinlock context.

CC: stable@vger.kernel.org # 4.9+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Partially revert "drm/amdgpu: update drm_display_info correctly when the edid is read"

[ Upstream commit 602ad43c3cd8f15cbb25ce9bb494129edb2024ed ]

This partially reverts 20543be93ca45968f344261c1a997177e51bd7e1.

Calling drm_connector_update_edid_property() in
amdgpu_connector_free_edid() causes a noticeable pause in
the system every 10 seconds on polled outputs so revert this
part of the change.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2257
Cc: Claudio Suarez <cssk@net-c.es>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: update drm_display_info correctly when the edid is read

[ Upstream commit 20543be93ca45968f344261c1a997177e51bd7e1 ]

drm_display_info is updated by drm_get_edid() or
drm_connector_update_edid_property(). In the amdgpu driver it is almost
always updated when the edid is read in amdgpu_connector_get_edid(),
but not always. Change amdgpu_connector_get_edid() and
amdgpu_connector_free_edid() to keep drm_display_info updated.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Claudio Suarez <cssk@net-c.es>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 602ad43c3cd8 ("drm/amdgpu: Partially revert "drm/amdgpu: update drm_display_info correctly when the edid is read"")
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/display/dp_mst: Fix drm_dp_mst_add_affected_dsc_crtcs() return code

[ Upstream commit 2f3a1273862cb82cca227630cc7f04ce0c94b6bb ]

Looks like that we're accidentally dropping a pretty important return code
here. For some reason, we just return -EINVAL if we fail to get the MST
topology state. This is wrong: error codes are important and should never
be squashed without being handled, which here seems to have the potential
to cause a deadlock.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Fixes: 8ec046716ca8 ("drm/dp_mst: Add helper to trigger modeset on affected DSC MST CRTCs")
Cc: <stable@vger.kernel.org> # v5.6+
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: move QUOTA_ENABLED check to rescan_should_stop from btrfs_qgroup_rescan_worker

[ Upstream commit db5df254120004471e1c957957ab2f1e612dcbd6 ]

Instead of having 2 places that short circuit the qgroup leaf scan have
everything in the qgroup_rescan_leaf function. In addition to that, also
ensure that the inconsistent qgroup flag is set when rescan_should_stop
returns true. This both retains the old behavior when -EINTR was set in
the body of the loop and at the same time also extends this behavior
when scanning is interrupted due to remount or unmount operations.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: f7e942b5bb35 ("btrfs: qgroup: fix sleep from invalid context bug in btrfs_qgroup_inherit()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock

[ Upstream commit db2d2dc9a0b58c6faefb6b002fdbed4f0362d1a4 ]

In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.

This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.

Fix this by setting *fres even if no clock dividers are in use.

This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.

With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:

spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0

Fixes: 6fd8b8503a0d ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e759387788 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: free btrfs_path before copying inodes to userspace

[ Upstream commit 418ffb9e3cf6c4e2574d3a732b724916684bd133 ]

btrfs_ioctl_logical_to_ino() frees the search path after the userspace
copy from the temp buffer @inodes. Which potentially can lead to a lock
splat.

Fix this by freeing the path before we copy @inodes to userspace.

CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: sink iterator parameter to btrfs_ioctl_logical_to_ino

[ Upstream commit e3059ec06b9f1a96826cc2bb6ed131aac0942446 ]

There's only one function we pass to iterate_inodes_from_logical as
iterator, so we can drop the indirection and call it directly, after
moving the function to backref.c

Signed-off-by: David Sterba <dsterba@suse.com>
Stable-dep-of: 418ffb9e3cf6 ("btrfs: free btrfs_path before copying inodes to userspace")
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 5.10.157

Link: https://lore.kernel.org/r/20221130180528.466039523@linuxfoundation.org
Tested-by: Pavel Machek (CIP) <pavel@denx.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Rudi Heitbaum <rudi@heitbaum.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fuse: lock inode unconditionally in fuse_fallocate()

commit 44361e8cf9ddb23f17bdcc40ca944abf32e83e79 upstream.

file_modified() must be called with inode lock held. fuse_fallocate()
didn't lock the inode in case of just FALLOC_KEEP_SIZE flags value, which
resulted in a kernel Warning in notify_change().

Lock the inode unconditionally, like all other fallocate implementations
do.

Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Reported-and-tested-by: syzbot+462da39f0667b357c4b6@syzkaller.appspotmail.com
Fixes: 4a6f278d4827 ("fuse: add file_modified() to fallocate")
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: fix TLB invalidation for Gen12 video and compute engines

commit 04aa64375f48a5d430b5550d9271f8428883e550 upstream.

In case of Gen12 video and compute engines, TLB_INV registers are masked -
to modify one bit, corresponding bit in upper half of the register must
be enabled, otherwise nothing happens.

CVE: CVE-2022-4139
Suggested-by: Chris Wilson <chris.p.wilson@intel.com>
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 7938d61591d3 ("drm/i915: Flush TLBs before releasing backing store")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: always register an MMU notifier for userptr

commit b39df63b16b64a3af42695acb9bc567aad144776 upstream.

Since switching to HMM we always need that because we no longer grab
references to the pages.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/dc/dce120: Fix audio register mapping, stop triggering KASAN

commit 44035ec2fde1114254ee465f9ba3bb246b0b6283 upstream.

There's been a very long running bug that seems to have been neglected for
a while, where amdgpu consistently triggers a KASAN error at start:

BUG: KASAN: global-out-of-bounds in read_indirect_azalia_reg+0x1d4/0x2a0 [amdgpu]
Read of size 4 at addr ffffffffc2274b28 by task modprobe/1889

After digging through amd's rather creative method for accessing registers,
I eventually discovered the problem likely has to do with the fact that on
my dce120 GPU there are supposedly 7 sets of audio registers. But we only
define a register mapping for 6 sets.

So, fix this and fix the KASAN warning finally.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: sysfs: normalize the error handling branch in btrfs_init_sysfs()

commit ffdbb44f2f23f963b8f5672e35c3a26088177a62 upstream.

Although kset_unregister() can eventually remove all attribute files,
explicitly rolling back with the matching function makes the code logic
look clearer.

CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: free btrfs_path before copying subvol info to userspace

commit 013c1c5585ebcfb19c88efe79063d0463b1b6159 upstream.

btrfs_ioctl_get_subvol_info() frees the search path after the userspace
copy from the temp buffer @subvol_info. This can lead to a lock splat
warning.

Fix this by freeing the path before we copy it to userspace.

CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: free btrfs_path before copying fspath to userspace

commit 8cf96b409d9b3946ece58ced13f92d0f775b0442 upstream.

btrfs_ioctl_ino_to_path() frees the search path after the userspace copy
from the temp buffer @ipath->fspath. Which potentially can lead to a lock
splat warning.

Fix this by freeing the path before we copy it to userspace.

CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: free btrfs_path before copying root refs to userspace

commit b740d806166979488e798e41743aaec051f2443f upstream.

Syzbot reported the following lockdep splat

======================================================
WARNING: possible circular locking dependency detected
6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0 Not tainted
------------------------------------------------------
syz-executor307/3029 is trying to acquire lock:
ffff0000c02525d8 (&mm->mmap_lock){++++}-{3:3}, at: __might_fault+0x54/0xb4 mm/memory.c:5576

but task is already holding lock:
ffff0000c958a608 (btrfs-root-00){++++}-{3:3}, at: __btrfs_tree_read_lock fs/btrfs/locking.c:134 [inline]
ffff0000c958a608 (btrfs-root-00){++++}-{3:3}, at: btrfs_tree_read_lock fs/btrfs/locking.c:140 [inline]
ffff0000c958a608 (btrfs-root-00){++++}-{3:3}, at: btrfs_read_lock_root_node+0x13c/0x1c0 fs/btrfs/locking.c:279

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (btrfs-root-00){++++}-{3:3}:
       down_read_nested+0x64/0x84 kernel/locking/rwsem.c:1624
       __btrfs_tree_read_lock fs/btrfs/locking.c:134 [inline]
       btrfs_tree_read_lock fs/btrfs/locking.c:140 [inline]
       btrfs_read_lock_root_node+0x13c/0x1c0 fs/btrfs/locking.c:279
       btrfs_search_slot_get_root+0x74/0x338 fs/btrfs/ctree.c:1637
       btrfs_search_slot+0x1b0/0xfd8 fs/btrfs/ctree.c:1944
       btrfs_update_root+0x6c/0x5a0 fs/btrfs/root-tree.c:132
       commit_fs_roots+0x1f0/0x33c fs/btrfs/transaction.c:1459
       btrfs_commit_transaction+0x89c/0x12d8 fs/btrfs/transaction.c:2343
       flush_space+0x66c/0x738 fs/btrfs/space-info.c:786
       btrfs_async_reclaim_metadata_space+0x43c/0x4e0 fs/btrfs/space-info.c:1059
       process_one_work+0x2d8/0x504 kernel/workqueue.c:2289
       worker_thread+0x340/0x610 kernel/workqueue.c:2436
       kthread+0x12c/0x158 kernel/kthread.c:376
       ret_from_fork+0x10/0x20 arch/arm64/kernel/entry.S:860

-> #2 (&fs_info->reloc_mutex){+.+.}-{3:3}:
       __mutex_lock_common+0xd4/0xca8 kernel/locking/mutex.c:603
       __mutex_lock kernel/locking/mutex.c:747 [inline]
       mutex_lock_nested+0x38/0x44 kernel/locking/mutex.c:799
       btrfs_record_root_in_trans fs/btrfs/transaction.c:516 [inline]
       start_transaction+0x248/0x944 fs/btrfs/transaction.c:752
       btrfs_start_transaction+0x34/0x44 fs/btrfs/transaction.c:781
       btrfs_create_common+0xf0/0x1b4 fs/btrfs/inode.c:6651
       btrfs_create+0x8c/0xb0 fs/btrfs/inode.c:6697
       lookup_open fs/namei.c:3413 [inline]
       open_last_lookups fs/namei.c:3481 [inline]
       path_openat+0x804/0x11c4 fs/namei.c:3688
       do_filp_open+0xdc/0x1b8 fs/namei.c:3718
       do_sys_openat2+0xb8/0x22c fs/open.c:1313
       do_sys_open fs/open.c:1329 [inline]
       __do_sys_openat fs/open.c:1345 [inline]
       __se_sys_openat fs/open.c:1340 [inline]
       __arm64_sys_openat+0xb0/0xe0 fs/open.c:1340
       __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
       invoke_syscall arch/arm64/kernel/syscall.c:52 [inline]
       el0_svc_common+0x138/0x220 arch/arm64/kernel/syscall.c:142
       do_el0_svc+0x48/0x164 arch/arm64/kernel/syscall.c:206
       el0_svc+0x58/0x150 arch/arm64/kernel/entry-common.c:636
       el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:654
       el0t_64_sync+0x18c/0x190 arch/arm64/kernel/entry.S:581

-> #1 (sb_internal#2){.+.+}-{0:0}:
       percpu_down_read include/linux/percpu-rwsem.h:51 [inline]
       __sb_start_write include/linux/fs.h:1826 [inline]
       sb_start_intwrite include/linux/fs.h:1948 [inline]
       start_transaction+0x360/0x944 fs/btrfs/transaction.c:683
       btrfs_join_transaction+0x30/0x40 fs/btrfs/transaction.c:795
       btrfs_dirty_inode+0x50/0x140 fs/btrfs/inode.c:6103
       btrfs_update_time+0x1c0/0x1e8 fs/btrfs/inode.c:6145
       inode_update_time fs/inode.c:1872 [inline]
       touch_atime+0x1f0/0x4a8 fs/inode.c:1945
       file_accessed include/linux/fs.h:2516 [inline]
       btrfs_file_mmap+0x50/0x88 fs/btrfs/file.c:2407
       call_mmap include/linux/fs.h:2192 [inline]
       mmap_region+0x7fc/0xc14 mm/mmap.c:1752
       do_mmap+0x644/0x97c mm/mmap.c:1540
       vm_mmap_pgoff+0xe8/0x1d0 mm/util.c:552
       ksys_mmap_pgoff+0x1cc/0x278 mm/mmap.c:1586
       __do_sys_mmap arch/arm64/kernel/sys.c:28 [inline]
       __se_sys_mmap arch/arm64/kernel/sys.c:21 [inline]
       __arm64_sys_mmap+0x58/0x6c arch/arm64/kernel/sys.c:21
       __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
       invoke_syscall arch/arm64/kernel/syscall.c:52 [inline]
       el0_svc_common+0x138/0x220 arch/arm64/kernel/syscall.c:142
       do_el0_svc+0x48/0x164 arch/arm64/kernel/syscall.c:206
       el0_svc+0x58/0x150 arch/arm64/kernel/entry-common.c:636
       el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:654
       el0t_64_sync+0x18c/0x190 arch/arm64/kernel/entry.S:581

-> #0 (&mm->mmap_lock){++++}-{3:3}:
       check_prev_add kernel/locking/lockdep.c:3095 [inline]
       check_prevs_add kernel/locking/lockdep.c:3214 [inline]
       validate_chain kernel/locking/lockdep.c:3829 [inline]
       __lock_acquire+0x1530/0x30a4 kernel/locking/lockdep.c:5053
       lock_acquire+0x100/0x1f8 kernel/locking/lockdep.c:5666
       __might_fault+0x7c/0xb4 mm/memory.c:5577
       _copy_to_user include/linux/uaccess.h:134 [inline]
       copy_to_user include/linux/uaccess.h:160 [inline]
       btrfs_ioctl_get_subvol_rootref+0x3a8/0x4bc fs/btrfs/ioctl.c:3203
       btrfs_ioctl+0xa08/0xa64 fs/btrfs/ioctl.c:5556
       vfs_ioctl fs/ioctl.c:51 [inline]
       __do_sys_ioctl fs/ioctl.c:870 [inline]
       __se_sys_ioctl fs/ioctl.c:856 [inline]
       __arm64_sys_ioctl+0xd0/0x140 fs/ioctl.c:856
       __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
       invoke_syscall arch/arm64/kernel/syscall.c:52 [inline]
       el0_svc_common+0x138/0x220 arch/arm64/kernel/syscall.c:142
       do_el0_svc+0x48/0x164 arch/arm64/kernel/syscall.c:206
       el0_svc+0x58/0x150 arch/arm64/kernel/entry-common.c:636
       el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:654
       el0t_64_sync+0x18c/0x190 arch/arm64/kernel/entry.S:581

other info that might help us debug this:

Chain exists of:
  &mm->mmap_lock --> &fs_info->reloc_mutex --> btrfs-root-00

Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(btrfs-root-00);
                               lock(&fs_info->reloc_mutex);
                               lock(btrfs-root-00);
  lock(&mm->mmap_lock);

*** DEADLOCK ***

1 lock held by syz-executor307/3029:
#0: ffff0000c958a608 (btrfs-root-00){++++}-{3:3}, at: __btrfs_tree_read_lock fs/btrfs/locking.c:134 [inline]
#0: ffff0000c958a608 (btrfs-root-00){++++}-{3:3}, at: btrfs_tree_read_lock fs/btrfs/locking.c:140 [inline]
#0: ffff0000c958a608 (btrfs-root-00){++++}-{3:3}, at: btrfs_read_lock_root_node+0x13c/0x1c0 fs/btrfs/locking.c:279

stack backtrace:
CPU: 0 PID: 3029 Comm: syz-executor307 Not tainted 6.0.0-rc7-syzkaller-18095-gbbed346d5a96 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/30/2022
Call trace:
dump_backtrace+0x1c4/0x1f0 arch/arm64/kernel/stacktrace.c:156
show_stack+0x2c/0x54 arch/arm64/kernel/stacktrace.c:163
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x104/0x16c lib/dump_stack.c:106
dump_stack+0x1c/0x58 lib/dump_stack.c:113
print_circular_bug+0x2c4/0x2c8 kernel/locking/lockdep.c:2053
check_noncircular+0x14c/0x154 kernel/locking/lockdep.c:2175
check_prev_add kernel/locking/lockdep.c:3095 [inline]
check_prevs_add kernel/locking/lockdep.c:3214 [inline]
validate_chain kernel/locking/lockdep.c:3829 [inline]
__lock_acquire+0x1530/0x30a4 kernel/locking/lockdep.c:5053
lock_acquire+0x100/0x1f8 kernel/locking/lockdep.c:5666
__might_fault+0x7c/0xb4 mm/memory.c:5577
_copy_to_user include/linux/uaccess.h:134 [inline]
copy_to_user include/linux/uaccess.h:160 [inline]
btrfs_ioctl_get_subvol_rootref+0x3a8/0x4bc fs/btrfs/ioctl.c:3203
btrfs_ioctl+0xa08/0xa64 fs/btrfs/ioctl.c:5556
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__arm64_sys_ioctl+0xd0/0x140 fs/ioctl.c:856
__invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
invoke_syscall arch/arm64/kernel/syscall.c:52 [inline]
el0_svc_common+0x138/0x220 arch/arm64/kernel/syscall.c:142
do_el0_svc+0x48/0x164 arch/arm64/kernel/syscall.c:206
el0_svc+0x58/0x150 arch/arm64/kernel/entry-common.c:636
el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:654
el0t_64_sync+0x18c/0x190 arch/arm64/kernel/entry.S:581

We do generally the right thing here, copying the references into a
temporary buffer, however we are still holding the path when we do
copy_to_user from the temporary buffer.  Fix this by freeing the path
before we copy to user space.

Reported-by: syzbot+4ef9e52e464c6ff47d9d@syzkaller.appspotmail.com
CC: stable@vger.kernel.org # 4.19+
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq: Take the proposed affinity at face value if force==true

From: Marc Zyngier <maz@kernel.org>

commit c48c8b829d2b966a6649827426bcdba082ccf922 upstream.

Although setting the affinity of an interrupt to a set of CPUs that doesn't
have any online CPU is generally frowned apon, there are a few limited
cases where such affinity is set from a CPUHP notifier, setting the
affinity to a CPU that isn't online yet.

The saving grace is that this is always done using the 'force' attribute,
which gives a hint that the affinity setting can be outside of the online
CPU mask and the callsite set this flag with the knowledge that the
underlying interrupt controller knows to handle it.

This restores the expected behaviour on Marek's system.

Fixes: 33de0aa4bae9 ("genirq: Always limit the affinity to online CPUs")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/4b7fc13c-887b-a664-26e8-45aed13f048a@samsung.com
Link: https://lore.kernel.org/r/20220414140011.541725-1-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

irqchip/gic-v3: Always trust the managed affinity provided by the core code

From: Marc Zyngier <maz@kernel.org>

commit 3f893a5962d31c0164efdbf6174ed0784f1d7603 upstream.

Now that the core code has been fixed to always give us an affinity
that only includes online CPUs, directly use this affinity when
computing a target CPU.

Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220405185040.206297-4-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq: Always limit the affinity to online CPUs

From: Marc Zyngier <maz@kernel.org>

commit 33de0aa4bae982ed6f7c777f86b5af3e627ac937 upstream.

[ Fixed small conflicts due to the HK_FLAG_MANAGED_IRQ flag been
renamed on upstream ]

When booting with maxcpus=<small number> (or even loading a driver
while most CPUs are offline), it is pretty easy to observe managed
affinities containing a mix of online and offline CPUs being passed
to the irqchip driver.

This means that the irqchip cannot trust the affinity passed down
from the core code, which is a bit annoying and requires (at least
in theory) all drivers to implement some sort of affinity narrowing.

In order to address this, always limit the cpumask to the set of
online CPUs.

Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20220405185040.206297-3-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

genirq/msi: Shutdown managed interrupts with unsatifiable affinities

From: Marc Zyngier <maz@kernel.org>

commit d802057c7c553ad426520a053da9f9fe08e2c35a upstream.

[ This commit is almost a rewrite because it conflicts with Thomas
  Gleixner's refactoring of this code in v5.17-rc1. I wasn't sure if
  I should drop all the s-o-bs (including Mark's), but decided
  to keep as the original commit ]

When booting with maxcpus=<small number>, interrupt controllers
such as the GICv3 ITS may not be able to satisfy the affinity of
some managed interrupts, as some of the HW resources are simply
not available.

The same thing happens when loading a driver using managed interrupts
while CPUs are offline.

In order to deal with this, do not try to activate such interrupt
if there is no online CPU capable of handling it. Instead, place
it in shutdown state. Once a capable CPU shows up, it will be
activated.

Reported-by: John Garry <john.garry@huawei.com>
Reported-by: David Decotigny <ddecotig@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20220405185040.206297-2-maz@kernel.org
Signed-off-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: wilc1000: validate number of channels

commit 0cdfa9e6f0915e3d243e2393bfa8a22e12d553b0 upstream.

There is no validation of 'e->no_of_channels' which can trigger an
out-of-bounds write in the following 'memset' call. Validate that the
number of channels does not extends beyond the size of the channel list
element.

Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-5-philipturnbull@github.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_CHANNEL_LIST attribute

commit f9b62f9843c7b0afdaecabbcebf1dbba18599408 upstream.

Validate that the IEEE80211_P2P_ATTR_CHANNEL_LIST attribute contains
enough space for a 'struct wilc_attr_oper_ch'. If the attribute is too
small then it can trigger an out-of-bounds write later in the function.

'struct wilc_attr_oper_ch' is variable sized so also check 'attr_len'
does not extend beyond the end of 'buf'.

Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-4-philipturnbull@github.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: wilc1000: validate length of IEEE80211_P2P_ATTR_OPER_CHANNEL attribute

commit 051ae669e4505abbe05165bebf6be7922de11f41 upstream.

Validate that the IEEE80211_P2P_ATTR_OPER_CHANNEL attribute contains
enough space for a 'struct struct wilc_attr_oper_ch'. If the attribute is
too small then it triggers an out-of-bounds write later in the function.

Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-3-philipturnbull@github.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: wilc1000: validate pairwise and authentication suite offsets

commit cd21d99e595ec1d8721e1058dcdd4f1f7de1d793 upstream.

There is no validation of 'offset' which can trigger an out-of-bounds
read when extracting RSN capabilities.

Signed-off-by: Phil Turnbull <philipturnbull@github.com>
Tested-by: Ajay Kathat <ajay.kathat@microchip.com>
Acked-by: Ajay Kathat <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221123153543.8568-2-philipturnbull@github.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm integrity: clear the journal on suspend

[ Upstream commit 984bf2cc531e778e49298fdf6730e0396166aa21 ]

There was a problem that a user burned a dm-integrity image on CDROM
and could not activate it because it had a non-empty journal.

Fix this problem by flushing the journal (done by the previous commit)
and clearing the journal (done by this commit). Once the journal is
cleared, dm-integrity won't attempt to replay it on the next
activation.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dm integrity: flush the journal on suspend

[ Upstream commit 5e5dab5ec763d600fe0a67837dd9155bdc42f961 ]

This commit flushes the journal on suspend. It is prerequisite for the
next commit that enables activating dm integrity devices in read-only mode.

Note that we deliberately didn't flush the journal on suspend, so that the
journal replay code would be tested. However, the dm-integrity code is 5
years old now, so that journal replay is well-tested, and we can make this
change now.

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpu: host1x: Avoid trying to use GART on Tegra20

[ Upstream commit c2418f911a31a266af4fbaca998dc73d3676475a ]

Since commit c7e3ca515e78 ("iommu/tegra: gart: Do not register with
bus") quite some time ago, the GART driver has effectively disabled
itself to avoid issues with the GPU driver expecting it to work in ways
that it doesn't. As of commit 57365a04c921 ("iommu: Move bus setup to
IOMMU device registration") that bodge no longer works, but really the
GPU driver should be responsible for its own behaviour anyway. Make the
workaround explicit.

Reported-by: Jon Hunter <jonathanh@nvidia.com>
Suggested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: usb: qmi_wwan: add Telit 0x103a composition

[ Upstream commit e103ba33998d0f25653cc8ebe745b68d1ee10cda ]

Add the following Telit LE910C4-WWX composition:

0x103a: rmnet

Signed-off-by: Enrico Sau <enrico.sau@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20221115105859.14324-1-enrico.sau@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: configurable source port perturb table size

[ Upstream commit aeac4ec8f46d610a10adbaeff5e2edf6a88ffc62 ]

On embedded systems with little memory and no relevant
security concerns, it is beneficial to reduce the size
of the table.

Reducing the size from 2^16 to 2^8 saves 255 KiB
of kernel RAM.

Makes the table size configurable as an expert option.

The size was previously increased from 2^8 to 2^16
in commit 4c2c8f03a5ab ("tcp: increase source port perturb table to
2^16").

Signed-off-by: Gleb Mazovetskiy <glex.spb@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: hp-wmi: Ignore Smart Experience App event

[ Upstream commit 8b9b6a044b408283b086702b1d9e3cf4ba45b426 ]

Sometimes hp-wmi driver complains on system resume:
[ 483.116451] hp_wmi: Unknown event_id - 33 - 0x0

According to HP it's a feature called "HP Smart Experience App" and it's
safe to be ignored.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20221114073842.205392-1-kai.heng.feng@canonical.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

zonefs: fix zone report size in __zonefs_io_error()

[ Upstream commit 7dd12d65ac646046a3fe0bbf9a4e86f4514207b3 ]

When an IO error occurs, the function __zonefs_io_error() is used to
issue a zone report to obtain the latest zone information from the
device. This function gets a zone report for all zones used as storage
for a file, which is always 1 zone except for files representing
aggregated conventional zones.

The number of zones of a zone report for a file is calculated in
__zonefs_io_error() by doing a bit-shift of the inode i_zone_size field,
which is equal to or larger than the device zone size. However, this
calculation does not take into account that the last zone of a zoned
device may be smaller than the zone size reported by bdev_zone_sectors()
(which is used to set the bit shift size). As a result, if an error
occurs for an IO targetting such last smaller zone, the zone report will
ask for 0 zones, leading to an invalid zone report.

Fix this by using the fact that all files require a 1 zone report,
except if the inode i_zone_size field indicates a zone size larger than
the device zone size. This exception case corresponds to a mount with
aggregated conventional zones.

A check for this exception is added to the file inode initialization
during mount. If an invalid setup is detected, emit an error and fail
the mount (check contributed by Johannes Thumshirn).

Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)

[ Upstream commit 1e817b889c7d8c14e7005258e15fec62edafe03c ]

Like the Acer Switch 10 (SW5-012) and Acer Switch 10 (S1003) models
the Acer Switch V 10 (SW5-017) supports reporting SW_TABLET_MODE
through acer-wmi.

Add a DMI quirk for the SW5-017 setting force_caps to ACER_CAP_KBD_DOCK
(these devices have no other acer-wmi based functionality).

Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221111111639.35730-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()

[ Upstream commit d0cdd85046b15089df71a50548617ac1025300d0 ]

pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before asus_wmi_set_xusb2pr() returns.

Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221111100752.134311-1-wangxiongfeng2@huawei.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/platform-pci: add missing free_irq() in error path

[ Upstream commit c53717e1e3f0d0f9129b2e0dbc6dcc5e0a8132e9 ]

free_irq() is missing in case of error in platform_pci_probe(), fix that.

Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Link: https://lore.kernel.org/r/20221114112124.1965611-1-ruanjinjie@huawei.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too

[ Upstream commit 5e29500eba2aa19e1323df46f64dafcd4a327092 ]

When Xen domain configures MSI-X, the usual approach is to enable MSI-X
together with masking all of them via the config space, then fill the
table and only then clear PCI_MSIX_FLAGS_MASKALL. Allow doing this via
QEMU running in a stub domain.

Previously, when changing PCI_MSIX_FLAGS_MASKALL was not allowed, the
whole write was aborted, preventing change to the PCI_MSIX_FLAGS_ENABLE
bit too.

Note the Xen hypervisor intercepts this write anyway, and may keep the
PCI_MSIX_FLAGS_MASKALL bit set if it wishes to. It will store the
guest-requested state and will apply it eventually.

Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Link: https://lore.kernel.org/r/20221114103110.1519413-1-marmarek@invisiblethingslab.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: soc_button_array - add Acer Switch V 10 to dmi_use_low_level_irq[]

[ Upstream commit e13757f52496444b994a7ac67b6e517a15d89bbc ]

Like on the Acer Switch 10 SW5-012, the Acer Switch V 10 SW5-017's _LID
method messes with home- and power-button GPIO IRQ settings, causing an
IRQ storm.

Add a quirk entry for the Acer Switch V 10 to the dmi_use_low_level_irq[]
DMI quirk list, to use low-level IRQs on this model, fixing the IRQ storm.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: soc_button_array - add use_low_level_irq module parameter

[ Upstream commit 8e9ada1d0e72b4737df400fe1bba48dc42a68df7 ]

It seems that the Windows drivers for the ACPI0011 soc_button_array
device use low level triggered IRQs rather then using edge triggering.

Some ACPI tables depend on this, directly poking the GPIO controller's
registers to clear the trigger type when closing a laptop's/2-in-1's lid
and re-instating the trigger when opening the lid again.

Linux sets the edge/level on which to trigger to both low+high since
it is using edge type IRQs, the ACPI tables then ends up also setting
the bit for level IRQs and since both low and high level have been
selected by Linux we get an IRQ storm leading to soft lockups.

As a workaround for this the soc_button_array already contains
a DMI quirk table with device models known to have this issue.

Add a module parameter for this so that users can easily test if their
device is affected too and so that they can use the module parameter
as a workaround.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221106215320.67109-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: goodix - try resetting the controller when no config is set

[ Upstream commit c7e37cc6240767f794678d11704935d49cc81d59 ]

On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver
does not reset the controller at probe time, because sometimes the system
firmware loads a config and resetting might loose this config.

On the Nanote UMPC-01 device OTOH the config is in flash of the controller,
the controller needs a reset to load this; and the system firmware does not
reset the controller on a cold boot.

To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try
resetting the controller and then re-reading the config when encountering
a config with 0 width/height/max_touch_num value and the controller has
not already been reset by goodix_ts_probe().

This should be safe to do in general because normally we should never
encounter a config with 0 width/height/max_touch_num. Doing this in
general not only avoids the need for a DMI quirk, but also might help
other systems.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()

[ Upstream commit 038ee49fef18710bedd38b531d173ccd746b2d8d ]

RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():

omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS.  If RTS uses active-low polarity, it is now asserted
for no reason.

The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register.  That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).

(up->mcr is not, as one might think, a cache of the MCR register's
current value.  Rather, it only caches a single bit of that register,
the AFE bit.  And it only does so if the UART supports the AFE bit,
which OMAP does not.  For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)

Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().

So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx().  Avoid by using a read-modify-write
when setting TCRTLR.

While at it, drop a redundant initialization of up->mcr.  As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c.  (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)

Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: bytcht_es8316: Add quirk for the Nanote UMPC-01

[ Upstream commit 8bb0ac0e6f64ebdf15d963c26b028de391c9bcf9 ]

The Nanote UMPC-01 mini laptop has stereo speakers, while the default
bytcht_es8316 settings assume a mono speaker setup. Add a quirk for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221025140942.509066-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode

[ Upstream commit ac5408991ea6b06e29129b4d4861097c4c3e0d59 ]

The device works fine in native RMI mode, there is no reason to use legacy
PS/2 mode with it.

Signed-off-by: Aman Dhoot <amandhoot12@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0

commit ef38de9217a04c9077629a24652689d8fdb4c6c6 upstream.

Some android userspace is sending BINDER_TYPE_FDA objects with
num_fds=0. Like the previous patch, this is reproducible when
playing a video.

Before commit 09184ae9b575 BINDER_TYPE_FDA objects with num_fds=0
were 'correctly handled', as in no fixup was performed.

After commit 09184ae9b575 we aggregate fixup and skip regions in
binder_ptr_fixup structs and distinguish between the two by using
the skip_size field: if it's 0, then it's a fixup, otherwise skip.
When processing BINDER_TYPE_FDA objects with num_fds=0 we add a
skip region of skip_size=0, and this causes issues because now
binder_do_deferred_txn_copies will think this was a fixup region.

To address that, return early from binder_translate_fd_array to
avoid adding an empty skip region.

Fixes: 09184ae9b575 ("binder: defer copies of pre-patched txn data")
Acked-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alessandro Astone <ales.astone@gmail.com>
Link: https://lore.kernel.org/r/20220415120015.52684-1-ales.astone@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: Address corner cases in deferred copy and fixup

commit 2d1746e3fda0c3612143d7c06f8e1d1830c13e23 upstream.

When handling BINDER_TYPE_FDA object we are pushing a parent fixup
with a certain skip_size but no scatter-gather copy object, since
the copy is handled standalone.
If BINDER_TYPE_FDA is the last children the scatter-gather copy
loop will never stop to skip it, thus we are left with an item in
the parent fixup list. This will trigger the BUG_ON().

This is reproducible in android when playing a video.
We receive a transaction that looks like this:
    obj[0] BINDER_TYPE_PTR, parent
    obj[1] BINDER_TYPE_PTR, child
    obj[2] BINDER_TYPE_PTR, child
    obj[3] BINDER_TYPE_FDA, child

Fixes: 09184ae9b575 ("binder: defer copies of pre-patched txn data")
Acked-by: Todd Kjos <tkjos@google.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Alessandro Astone <ales.astone@gmail.com>
Link: https://lore.kernel.org/r/20220415120015.52684-2-ales.astone@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: fix pointer cast warning

commit 9a0a930fe2535a76ad70d3f43caeccf0d86a3009 upstream.

binder_uintptr_t is not the same as uintptr_t, so converting it into a
pointer requires a second cast:

drivers/android/binder.c: In function 'binder_translate_fd_array':
drivers/android/binder.c:2511:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
2511 | sender_ufda_base = (void __user *)sender_uparent->buffer + fda->parent_offset;
| ^

Fixes: 656e01f3ab54 ("binder: read pre-translated fds from sender buffer")
Acked-by: Todd Kjos <tkjos@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211207122448.1185769-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: defer copies of pre-patched txn data

commit 09184ae9b5756cc469db6fd1d1cfdcffbf627c2d upstream.

BINDER_TYPE_PTR objects point to memory areas in the
source process to be copied into the target buffer
as part of a transaction. This implements a scatter-
gather model where non-contiguous memory in a source
process is "gathered" into a contiguous region in
the target buffer.

The data can include pointers that must be fixed up
to correctly point to the copied data. To avoid making
source process pointers visible to the target process,
this patch defers the copy until the fixups are known
and then copies and fixeups are done together.

There is a special case of BINDER_TYPE_FDA which applies
the fixup later in the target process context. In this
case the user data is skipped (so no untranslated fds
become visible to the target).

Reviewed-by: Martijn Coenen <maco@android.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211130185152.437403-5-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[cmllamas: fix trivial merge conflict]
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: read pre-translated fds from sender buffer

commit 656e01f3ab54afe71bed066996fc2640881e1220 upstream.

This patch is to prepare for an up coming patch where we read
pre-translated fds from the sender buffer and translate them before
copying them to the target.  It does not change run time.

The patch adds two new parameters to binder_translate_fd_array() to
hold the sender buffer and sender buffer parent.  These parameters let
us call copy_from_user() directly from the sender instead of using
binder_alloc_copy_from_buffer() to copy from the target.  Also the patch
adds some new alignment checks.  Previously the alignment checks would
have been done in a different place, but this lets us print more
useful error messages.

Reviewed-by: Martijn Coenen <maco@android.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211130185152.437403-4-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder: avoid potential data leakage when copying txn

commit 6d98eb95b450a75adb4516a1d33652dc78d2b20c upstream.

Transactions are copied from the sender to the target
first and objects like BINDER_TYPE_PTR and BINDER_TYPE_FDA
are then fixed up. This means there is a short period where
the sender's version of these objects are visible to the
target prior to the fixups.

Instead of copying all of the data first, copy data only
after any needed fixups have been applied.

Fixes: 457b9a6f09f0 ("Staging: android: add binder driver")
Reviewed-by: Martijn Coenen <maco@android.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20211130185152.437403-3-tkjos@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[cmllamas: fix trivial merge conflict]
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/ioremap: Fix page aligned size calculation in __ioremap_caller()

commit 4dbd6a3e90e03130973688fd79e19425f720d999 upstream.

Current code re-calculates the size after aligning the starting and
ending physical addresses on a page boundary. But the re-calculation
also embeds the masking of high order bits that exceed the size of
the physical address space (via PHYSICAL_PAGE_MASK). If the masking
removes any high order bits, the size calculation results in a huge
value that is likely to immediately fail.

Fix this by re-calculating the page-aligned size first. Then mask any
high order bits using PHYSICAL_PAGE_MASK.

Fixes: ffa71f33a820 ("x86, ioremap: Fix incorrect physical address handling in PAE mode")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/1668624097-14884-2-git-send-email-mikelley@microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>