drm: bridge: ti-sn65dsi83: Add error recovery mechanism

In some cases observed during ESD tests, the TI SN65DSI83 cannot recover
from errors by itself. A full restart of the bridge is needed in those
cases to have the bridge output LVDS signals again.

Also, during tests, cases were observed where reading the status of the
bridge was not even possible. Indeed, in those cases, the bridge stops
to acknowledge I2C transactions. Only a full reset of the bridge (power
off/on) brings back the bridge to a functional state.

The TI SN65DSI83 has some error detection capabilities. Introduce an
error recovery mechanism based on this detection.

The errors detected are signaled through an interrupt. On system where
this interrupt is not available, the driver uses a polling monitoring
fallback to check for errors. When an error is present or when reading
the bridge status leads to an I2C failure, the recovery process is
launched.

Restarting the bridge needs to redo the initialization sequence. This
initialization sequence has to be done with the DSI data lanes driven in
LP11 state. In order to do that, the recovery process resets the whole
output path (i.e the path from the encoder to the connector) where the
bridge is located.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-5-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/vc4: hdmi: Use drm_atomic_helper_reset_crtc()

The current code uses a the reset_pipe() local function to reset the
CRTC outputs.

drm_atomic_helper_reset_crtc() has been introduced recently and it
performs exact same operations.

In order to avoid code duplication, use the new helper instead of the
local function.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-4-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/atomic-helper: Introduce drm_atomic_helper_reset_crtc()

drm_atomic_helper_reset_crtc() allows to reset the CRTC active outputs.

This resets all active components available between the CRTC and
connectors.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-3-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

dt-bindings: display: bridge: sn65dsi83: Add interrupt

Both the TI SN65DSI83 and SN65DSI84 bridges have an IRQ pin to signal
errors using interrupt.

This interrupt is not documented in the binding.

Add the missing interrupts property.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-2-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/vkms: Fix use after free and double free on init error

If the driver initialization fails, the vkms_exit() function might
access an uninitialized or freed default_config pointer and it might
double free it.

Fix both possible errors by initializing default_config only when the
driver initialization succeeded.

Reported-by: Louis Chauvet <louis.chauvet@bootlin.com>
Closes: https://lore.kernel.org/all/Z5uDHcCmAwiTsGte@louis-chauvet-laptop/
Fixes: 2df7af93fdad ("drm/vkms: Add vkms_config type")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmremann@suse.de>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250212084912.3196-1-jose.exposito89@gmail.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>

drm: writeback: Fix use after free in drm_writeback_connector_cleanup()

The drm_writeback_cleanup_job() function frees "pos" so call
list_del(&pos->list_entry) first to avoid a use after free.

Fixes: 1914ba2b91ea ("drm: writeback: Create drmm variants for drm_writeback_connector initialization")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78abd541-71e9-4b3b-a05d-2c7caf8d5b2f@stanley.mountain
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/tests: Fix a test in drm_test_check_valid_clones()

The drm_atomic_get_crtc_state() function returns error pointers and not
NULL.  Update the check to check for error pointers as well as NULL.

Fixes: 88849f24e2ab ("drm/tests: Add test for drm_atomic_helper_check_modeset()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/c50f11c7-932c-47dc-b40f-4ada8b9b6679@stanley.mountain
Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm: drop i2c subdir from Makefile

The commit 325ba852d148 ("drm/i2c: move TDA998x driver under
drivers/gpu/drm/bridge") deleted the drivers/gpu/drm/i2c/ subdir, but
didn't update upper level Makefile. Drop corresponding line to fix build
issues.

Fixes: 325ba852d148 ("drm/i2c: move TDA998x driver under drivers/gpu/drm/bridge")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/dri-devel/20250213113841.7645b74c@canb.auug.org.au
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213-fix-tda-v1-1-d3d34b2dc907@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/i2c: move TDA998x driver under drivers/gpu/drm/bridge

TDA998x is the HDMI bridge driver, incorporating drm_connector and
optional drm_encoder (created via the component bind API by the TICLDC
and HDLCD drivers). Thus it should be residing together with the other
DRM bridge drivers under drivers/gpu/drm/bridge/.

Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113-drm-move-tda998x-v3-3-214e0682a5e4@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

media: cec: move driver for TDA9950 from drm/i2c

Move the driver for NXP TDA9950 / CEC part of TDA998x together to
drivers/media/i2c, close to other CEC drivers. Specify 'default
DRM_I2C_NXP_TDA998X' in order to simplify migration from old config
files as the Kconfig name has been changed to follow media/cec style.

Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113-drm-move-tda998x-v3-2-214e0682a5e4@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/i2c: tda998x: drop support for platform_data

After the commit 0fb2970b4b6b ("drm/armada: remove non-component
support") there are no remaining users of the struct
tda998x_encoder_params. Drop the header and corresponding API from the
TDA998x driver.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113-drm-move-tda998x-v3-1-214e0682a5e4@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drm/panel: visionox-r66451: transition to mipi_dsi wrapped functions

Change the visionox-r66451 panel to use multi style functions for
improved error handling. Additionally, always drop LPM flag after
sending init sequence.

Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210092342.287324-1-tejasvipin76@gmail.com

MAINTAINERS: Add TTM reviewers

Add Matthew Auld and Matthew Brost as TTM reviewers

Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Simona Vetter <simona.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.com>
Acked-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206103544.36971-1-thomas.hellstrom@linux.intel.com

drm/v3d: Add clock handling

Since the initial commit 57692c94dcbe ("drm/v3d: Introduce a new DRM driver
for Broadcom V3D V3.x+") the struct v3d_dev reserved a pointer for
an optional V3D clock. But there wasn't any code, which fetched it.
So add the missing clock handling before accessing any V3D registers.

Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250201125046.33030-1-wahrenst@gmx.net

drm/sched: Use struct for drm_sched_init() params

drm_sched_init() has a great many parameters and upcoming new
functionality for the scheduler might add even more. Generally, the
great number of parameters reduces readability and has already caused
one missnaming, addressed in:

commit 6f1cacf4eba7 ("drm/nouveau: Improve variable name in
nouveau_sched_init()").

Introduce a new struct for the scheduler init parameters and port all
users.

Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthew Brost <matthew.brost@intel.com> # for Xe
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> # for Panfrost and Panthor
Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com> # for Etnaviv
Reviewed-by: Frank Binns <frank.binns@imgtec.com> # for Imagination
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com> # for Sched
Reviewed-by: Maíra Canal <mcanal@igalia.com> # for v3d
Reviewed-by: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Lizhi Hou <lizhi.hou@amd.com> # for amdxdna
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211111422.21235-2-phasta@kernel.org

drm: ensure drm headers are self-contained and pass kernel-doc

Ensure drm headers build, are self-contained, have header guards, and
have no kernel-doc warnings, when CONFIG_DRM_HEADER_TEST=y.

The mechanism follows similar patters used in i915, xe, and usr/include.

To cover include/drm, we need to recurse there using the top level
Kbuild and the new include/Kbuild files.

v4: check for CONFIG_WERROR in addition to CONFIG_DRM_WERROR

v3: adapt to upstream build changes

v2: make DRM_HEADER_TEST depend on DRM

Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Simona Vetter <simona.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/d8ad1c6d707f38a55987f616cb9650aef30b84e1.1737556766.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/client: include types.h to make drm_client_event.h self-contained

drm_client_event.h uses bool without types.h, include it.

Fixes: bf17766f1083 ("drm/client: Move suspend/resume into DRM client callbacks")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Simona Vetter <simona.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/6c69cb005cc3a2b968b6c9675d0ba03173f6c574.1737556766.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm: zynqmp_dp: Use devm_platform_ioremap_resource_byname()

platform_get_resource_byname() and devm_ioremap_resource() can be
replaced by devm_platform_ioremap_resource_byname(), which can
simplify the code logic a bit, No functional change here.

Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240828084929.2527228-1-ruanjinjie@huawei.com

drm: zynqmp_dp: Use scope-based mutex helpers

Convert most mutex_(un)lock calls to use (scoped_)guard instead. This
generally reduces line count and prevents bugs like forgetting to unlock
the mutex. I've left traditional calls in a few places where scoped
helpers would be more verbose. This mostly happens where
debugfs_file_put needs to be called regardless. I looked into defining a
CLASS for debugfs_file, but it seems like more effort than it's worth
since debugfs_file_get can fail.

Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250207162528.1651426-3-sean.anderson@linux.dev

drm: zynqmp_dp: Fix a deadlock in zynqmp_dp_ignore_hpd_set()

Instead of attempting the same mutex twice, lock and unlock it.

This bug has been detected by the Clang thread-safety analyzer.

Cc: Sean Anderson <sean.anderson@linux.dev>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 28edaacb821c ("drm: zynqmp_dp: Add debugfs interface for compliance testing")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250207162528.1651426-2-sean.anderson@linux.dev

drm/edp-panel: Add panel used by T14s Gen6 Snapdragon

The Lenovo Thinkpad T14s Gen6 Snapdragon is currently sold with three
different panel versions: OLED, Low Power IPS or IPS with Touchscreen.

My Low Power IPS version had this panel and the kernel complained
about not knowing any details.  I don't have any panel documentation,
but as far as I can see the same timings for the already supported
CSO panel also work for this one.

The raw EDID is:

00 ff ff ff ff ff ff 00 0e 6f 13 14 00 00 00 00
00 1e 01 04 a5 1e 13 78 03 82 53 a4 55 4d 9b 24
0d 51 55 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 35 3c 80 a0 70 b0 23 40 30 20
36 00 2e bd 10 00 00 18 00 00 00 fd 00 30 3c 4a
4a 0f 01 0a 20 20 20 20 20 20 00 00 00 fe 00 43
53 4f 54 20 54 33 0a 20 20 20 20 20 00 00 00 fe
00 4d 4e 45 30 30 37 4a 41 31 2d 32 0a 20 00 8b

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211014314.94429-1-sre@ring0.de

drm: xlnx: zynqmp_dpsub: Add NULL check in zynqmp_audio_init

devm_kasprintf() calls can return null pointers on failure.
But some return values were not checked in zynqmp_audio_init().

Add NULL check in zynqmp_audio_init(), avoid referencing null
pointers in the subsequent code.

Fixes: 3ec5c1579305 ("drm: xlnx: zynqmp_dpsub: Add DP audio support")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211102049.6468-1-hanchunchao@inspur.com

drm: xlnx: zynqmp: Fix max dma segment size

Fix "mapping sg segment longer than device claims to support" warning by
setting the max segment size.

Fixes: d76271d22694 ("drm: xlnx: DRM/KMS driver for Xilinx ZynqMP DisplayPort Subsystem")
Reviewed-by: Sean Anderson <sean.anderson@linux.dev>
Tested-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250115-xilinx-formats-v2-10-160327ca652a@ideasonboard.com

drm/mgag200: Added support for the new device G200eH5

- Added the new device ID
- Added new pll algorithm

Signed-off-by: Gwenael Georgeault <ggeorgea@matrox.com>
Co-authored-by: Mamadou Insa Diop <mdiop@matrox.com>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/alpine.LFD.2.00.2502071401180.14188@pluton.matrox.com

drm/ast: astdp: Validate display modes

Validate each display mode against the astdp transmitter chips. Filters
out modes that the chip does not support.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204133209.403327-5-tzimmermann@suse.de

drm/ast: astdp: Store mode index in connector state

Look up the mode index for the astdp transmitter ship in the encoder's
atomic check and report an error if the display mode is not supported.

The lookup uses the DRM display mode instead of the driver's internal
VBIOS mode. Both are equivalent. The modesetting code later reads
the calculated index from the connector state to avoid recalculating it.

v2:
- fix typo in commit message (Jocelyn)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204133209.403327-4-tzimmermann@suse.de

drm/ast: astdp: Inline mode-index calculation

Programming the astdp transmitter chip requires a magic value for
individual modes. Inline the helper for calculating the value into
its only caller (i.e., the encoder's atomic_mode_set).

With further refactoring, the atomic check will be able to detect
invalid modes before attempting to program them.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204133209.403327-3-tzimmermann@suse.de

drm/ast: astdp: Add connector state

Add dedicated connector state for ASTDP connectors. The state will
store values for programming the transmitter chip.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204133209.403327-2-tzimmermann@suse.de

drm/bridge: dw-hdmi: Sync comment block with actual bus formats order

Commit d3d6b1bf85ae ("drm: bridge: dw_hdmi: fix preference of RGB modes
over YUV420") changed the order of the output bus formats, but missed to
update accordingly the "Possible output formats" comment section above
dw_hdmi_bridge_atomic_get_output_bus_fmts().

Fix the misleading comment block and a context related typo.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-dw-hdmi-bus-fmt-order-v2-1-d0aaeb7a697a@collabora.com

drm/bridge: ti-sn65dsi86: remove unused drm_panel.h include

The file uses the panel_bridge APIs from drm_bridge.h, but no drm_panel
APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-8-93df60faa756@bootlin.com

drm/bridge: ti-sn65dsi83: remove unused drm_panel.h include

The file uses the panel_bridge APIs from drm_bridge.h, but no drm_panel
APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-7-93df60faa756@bootlin.com

drm/bridge: tc358775: remove unused drm_panel.h include

The file uses the panel_bridge APIs from drm_bridge.h, but no drm_panel
APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-6-93df60faa756@bootlin.com

drm/bridge: tc358762: remove unused drm_panel.h include, add drm_bridge.h

The file uses the panel_bridge APIs from drm_bridge.h, which is included
only indirectly, and uses no drm_panel APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-5-93df60faa756@bootlin.com

drm/bridge: parade-ps8640: remove unused drm_panel.h include

The file uses the panel_bridge APIs from drm_bridge.h, but no drm_panel
APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-4-93df60faa756@bootlin.com

drm/bridge: parade-ps8622: remove unused drm_panel.h include

The file uses the panel_bridge APIs from drm_bridge.h, but no drm_panel
APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-3-93df60faa756@bootlin.com

drm/bridge: nxp-ptn3460: remove unused drm_panel.h include

The file uses the panel_bridge APIs from drm_bridge.h, but no drm_panel
APIs from drm_panel.h.

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-2-93df60faa756@bootlin.com

drm/panel: remove unnecessary forward declaration

'struct drm_device' is not used at all in this file since commit
aa6c43644bc5 ("drm/panel: drop drm_device from drm_panel").

Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206-drm-cleanups-v1-1-93df60faa756@bootlin.com

drm/panel: panel-himax-hx83102: support for starry-2082109qfh040022-50e MIPI-DSI panel

The starry-2082109qfh040022-50e is a 10.95" TFT panel. The MIPI controller
on this panel is the same as the other panels here, so add this panel to
this driver.

Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250208105326.3850358-4-yelangyan@huaqin.corp-partner.google.com

drm/panel: panel-himax-hx83102: support for kingdisplay-kd110n11-51ie MIPI-DSI panel

The kingdisplay-kd110n11-51ie is a 10.95" TFT panel. The MIPI controller
on this panel is the same as the other panels here, so add this panel
to this driver.

Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250208105326.3850358-3-yelangyan@huaqin.corp-partner.google.com

dt-bindings: display: panel: Add KD110N11-51IE and 2082109QFH040022-50E

Add a new compatible for the panels KINGDISPLAY KD110N11-51IE and
STARRY 2082109QFH040022-50E. Both panels use the HX83102 IC, so
add the compatible to the hx83102 bindings file.

Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250208105326.3850358-2-yelangyan@huaqin.corp-partner.google.com

drm/bridge: convert to use devm_platform_ioremap_resource()

convert to use devm_platform_ioremap_resource().

Signed-off-by: Shixiong Ou <oushixiong@kylinos.cn>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-and-tested-by: Dharma Balasubiramani <dharma.b@microchip.com>
Reviewed-by: Dharma Balasubiramani <dharma.b@microchip.com>
Tested-by: Dharma Balasubiramani <dharma.b@microchip.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206071713.180471-1-oushixiong1025@163.com

drm/ttm: use ttm_resource_unevictable() to replace pin_count and swapped

TTM always uses pin_count and ttm_resource_is_swapped() together to
determine whether a BO is unevictable.
Now use ttm_resource_unevictable() to replace them.

Signed-off-by: Zhaoyu Liu <liuzhaoyu.zackary@bytedance.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250126093256.GA688734@bytedance
Signed-off-by: Christian König <christian.koenig@amd.com>

accel/ivpu: Implement D0i2 disable test mode

Add power_profile firmware boot param and set it to 0 by default
which is default FW power profile.

Implement IVPU_TEST_MODE_D0I2_DISABLE which is used for setting
power profile boot param value to 1 which prevents NPU from entering
d0i2 power state.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204084622.2422544-7-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Add test modes to toggle clock relinquish disable

Add IVPU_TEST_MODE_CLK_RELINQ_[DISABLE|ENABLE] that overrides
workaround for disabling clock relinquish for testing purposes.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204084622.2422544-6-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Allow to import single buffer into multiple contexts

Use ivpu_gem_prime_import() based on drm_gem_prime_import_dev()
for importing buffers, removing optimization for same device
imports. This optimization reused the same ivpu_bo object in multiple
contexts but a single buffer can be MMU-mapped only to a single context.
Each import now creates a new instance of ivpu_bo object that shares
the same sg_table but have separate MMU mappings.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Tomasz Rusinowicz <tomasz.rusinowicz@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204084622.2422544-5-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Add debugfs interface for setting HWS priority bands

Add debugfs interface to modify following priority bands properties:
 * grace period
 * process grace period
 * process quantum

This allows for the adjustment of hardware scheduling algorithm parameters
for each existing priority band, facilitating validation and fine-tuning.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204084622.2422544-4-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Prevent runtime suspend during context abort work

Increment the runtime PM counter when entering
ivpu_context_abort_work_fn() to prevent the device
from suspending while the function is executing.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Andrzej Kacprowski <Andrzej.Kacprowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204084622.2422544-3-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Add missing locks around mmu queues

Multiple threads were accessing mmu cmd queue simultaneously
causing sporadic failures in ivpu_mmu_cmdq_sync() function.
Protect critical code with mmu mutex.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Andrzej Kacprowski <Andrzej.Kacprowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204084622.2422544-2-jacek.lawrynowicz@linux.intel.com

drm/virtio: Add drm_panic support

Virtio gpu supports the drm_panic module, which displays a message to
the screen when a kernel panic occurs. It is supported where it has
vmapped shmem BO.

Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Signed-off-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206104300.416014-1-ryasuoka@redhat.com

drm/panel: panel-himax-hx83102: support for csot-pna957qt1-1 MIPI-DSI panel

The csot-pna957qt1-1 is a 10.95" TFT panel. The MIPI controller on this
panel is the same as the other panels here, so add this panel to this
driver.

Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206131300.1295111-4-yelangyan@huaqin.corp-partner.google.com

dt-bindings: display: panel: Add compatible for CSOT PNA957QT1-1

Add a new compatible for the panel CSOT PNA957QT1-1. This panel uses
HX83102 IC, so add the compatible to the hx83102 binding files.

Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206131300.1295111-3-yelangyan@huaqin.corp-partner.google.com

dt-bindings: vendor-prefixes: add csot

Add "csot" to the Devicetree Vendor Prefix Registry.

Signed-off-by: Langyan Ye <yelangyan@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206131300.1295111-2-yelangyan@huaqin.corp-partner.google.com

drm/panthor: Convert IOCTL defines to an enum

Use an enum instead of #defines for panthor IOCTLs. This allows the
header to be used with Rust code as bindgen can't handle complex
defines.

Cc: Beata Michalska <beata.michalska@arm.com>
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204232824.3819437-1-robh@kernel.org

drm/panic: Better binary encoding in QR code

The current encoding, is done by converting 13bits of input into 4
decimal digits, that are then encoded efficiently using the numeric
encoding of the QR code specification.
The Fido v2.2 specification [1] uses a similar approach for its
QR-initiated authentication. The only difference is that it converts
7 bytes (56bits) of input into 17 decimal digits. The benefit is that
the algorithm doesn't require to split input bytes into 13bits chunk,
and the ratio is a bit better.
This improvement was proposed by Jó Ágila Bitsch in [2].
drm_panic is still young, and the QR code feature is not widely used,
so it's still time to switch to a common algorithm, shared with a
widely used standard.
I also changed the name of the url parameter, from zl= to z=, so the
website can keep backward compatibility if needed.

[1] https://fidoalliance.org/specs/fido-v2.2-rd-20230321/fido-client-to-authenticator-protocol-v2.2-rd-20230321.html#hybrid-qr-initiated
[2] https://github.com/kdj0c/panic_report/issues/2

Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250128165254.893204-1-jfalempe@redhat.com

drm/panthor: Fix race condition when gathering fdinfo group samples

Commit e16635d88fa0 ("drm/panthor: add DRM fdinfo support") failed to
protect access to groups with an xarray lock, which could lead to
use-after-free errors.

Fixes: e16635d88fa0 ("drm/panthor: add DRM fdinfo support")
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250130172851.941597-6-adrian.larumbe@collabora.com
Link: https://patchwork.freedesktop.org/patch/msgid/20250107173310.88329-1-florent.tomasin@arm.com

Documentation/gpu: Add fdinfo meanings of panthor-*-memory tags

A previous commit enabled display of driver-internal kernel BO sizes
through the device file's fdinfo interface.

Expand the description of the relevant driver-specific key:value pairs
with the definitions of the new panthor-*-memory ones.

Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250130172851.941597-5-adrian.larumbe@collabora.com

drm/panthor: Expose size of driver internal BO's over fdinfo

This will display the sizes of kenrel BO's bound to an open file, which are
otherwise not exposed to UM through a handle.

The sizes recorded are as follows:
 - Per group: suspend buffer, protm-suspend buffer, syncobjcs
 - Per queue: ringbuffer, profiling slots, firmware interface
 - For all heaps in all heap pools across all VM's bound to an open file,
 record size of all heap chuks, and for each pool the gpu_context BO too.

This does not record the size of FW regions, as these aren't bound to a
specific open file and remain active through the whole life of the driver.

Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250130172851.941597-4-adrian.larumbe@collabora.com

drm/file: Add fdinfo helper for printing regions with prefix

This is motivated by the desire of some drivers (eg. Panthor) to print the
size of internal memory regions with a prefix that reflects the driver
name, as suggested in the previous documentation commit.

That means adding a new argument to print_size and making it available for
DRM users.

Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250130172851.941597-3-adrian.larumbe@collabora.com

Documentation/gpu: Clarify format of driver-specific fidnfo keys

This change reflects de facto usage by amdgpu, as exemplified by commit
d6530c33a978 ("drm/amdgpu: expose more memory stats in fdinfo").

Cc: Tvrtko Ursulin <tursulin@ursulin.net>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Signed-off-by: Adrián Larumbe <adrian.larumbe@collabora.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250130172851.941597-2-adrian.larumbe@collabora.com

drm/scheduler: Remove some unused prototypes

As far as I can tell some removed prototypes were introduced by probably
bad conflict resolution in
fc58764bbf60 ("Merge tag 'amd-drm-next-6.2-2022-11-18' of https://gitlab.freedesktop.org/agd5f/linux into drm-next").

Remove them.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Philipp Stanner <pstanner@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250205110410.7941-1-tvrtko.ursulin@igalia.com

drm/bridge: it6505: fix HDCP V match check is not performed correctly

Fix a typo where V compare incorrectly compares av[] with av[] itself,
which can result in HDCP failure.

The loop of V compare is expected to iterate for 5 times
which compare V array form av[0][] to av[4][].
It should check loop counter reach the last statement "i == 5"
before return true

Fixes: 0989c02c7a5c ("drm/bridge: it6505: fix HDCP CTS compare V matching")
Signed-off-by: Hermes Wu <Hermes.wu@ite.com.tw>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250121-fix-hdcp-v-comp-v4-1-185f45c728dc@ite.com.tw

Merge drm/drm-next into drm-misc-next

Bring rc1 to start the new release dev.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

drm/rockchip: vop2: Improve display modes handling on RK3588 HDMI0

The RK3588 specific implementation is currently quite limited in terms
of handling the full range of display modes supported by the connected
screens, e.g. 2560x1440@75Hz, 2048x1152@60Hz, 1024x768@60Hz are just a
few of them.

Additionally, it doesn't cope well with non-integer refresh rates like
59.94, 29.97, 23.98, etc.

Make use of HDMI0 PHY PLL as a more accurate DCLK source to handle
all display modes up to 4K@60Hz.

Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-vop2-hdmi0-disp-modes-v3-3-d71c6a196e58@collabora.com

drm/rockchip: vop2: Drop unnecessary if_pixclk_rate computation

The if_pixclk_rate variable is not being used outside of the if-block in
rk3588_calc_cru_cfg(), hence move the superfluous assignment from the
first branch to the inner comment-block.

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-vop2-hdmi0-disp-modes-v3-2-d71c6a196e58@collabora.com

dt-bindings: display: vop2: Add optional PLL clock properties

On RK3588, HDMI PHY PLL can be used as an alternative and more accurate
pixel clock source for VOP2 video ports 0, 1 and 2.

Document the optional PLL clock properties corresponding to the two HDMI
PHYs available on the SoC.

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-vop2-hdmi0-disp-modes-v3-1-d71c6a196e58@collabora.com

dt-bindings: display: rockchip: Fix label name of hdptxphy for RK3588 HDMI TX Controller

The hdptxphy is a combo transmit-PHY for HDMI2.1 TMDS Link, FRL Link, DP
and eDP Link. Therefore, it is better to name it hdptxphy0 other than
hdptxphy_hdmi0, which will be referenced by both hdmi0 and edp0 nodes.

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250206030330.680424-2-damon.ding@rock-chips.com

drm/panel: sharp-ls060t1sx01: transition to mipi_dsi wrapped functions

Changes the sharp-ls060t1sx01 panel to use multi style functions for
improved error handling.

Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250201185439.157613-1-tejasvipin76@gmail.com

drm/edp-panel: Add LG Display panel model LP079QX1-SP0V

The raw edid for LP079QX1-SP0V panel model is:

00 ff ff ff ff ff ff 00 16 83 00 00 00 00 00 00
04 17 01 00 a5 10 0c 78 06 ef 05 a3 54 4c 99 26
0f 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 ea 4e 00 4c 60 00 14 80 0c 10
84 00 78 a0 00 00 00 18 00 00 00 10 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 fe 00 4c
50 30 37 39 51 58 31 2d 53 50 30 56 00 00 00 fc
00 43 6f 6c 6f 72 20 4c 43 44 0a 20 20 20 00 3f

Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250205094734.562992-1-damon.ding@rock-chips.com

drm/ci: update expectation files

Update expectation files for the mesa uprev.

Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250205081652.1928927-4-vignesh.raman@collabora.com

drm/ci: update gitlab rules

Update gitlab rules to include scheduled pipelines.

Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250205081652.1928927-3-vignesh.raman@collabora.com

drm/ci: uprev mesa

Uprev mesa to adapt to the latest changes in mesa ci
which includes new container jobs and stages. Also update
lava-submit script to adapt to the recent changes in mesa
to use LAVA rootfs overlays.

Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250205081652.1928927-2-vignesh.raman@collabora.com

drm/vkms: Add support for ABGR8888 pixel format

Add support for pixel format ABGR8888, which is the default format
on Android devices. This will allow us to use VKMS as the default
display driver in Android Emulator (Cuttlefish) and increase VKMS
adoption.

Signed-off-by: Paz Zcharya <pazz@chromium.org>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129142238.562999-1-pazz@google.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>

drm/atomic-helper: improve CRTC enabled/connectors mismatch logging message

This message reports a mismatch between new_crtc_state->enable and
has_connectors, which should be either both true or both false. However it
does not mention which one is true and which is false, which can be useful
for debugging. Add the value of both avriables to the log message.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Louis Chauvet <louis.chauvet@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-drm-small-improvements-v4-2-d6bbc92f12f1@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>

drm/drm_mode_object: fix typo in kerneldoc

Remove unintended extra word.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Louis Chauvet <louis.chauvet@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-drm-small-improvements-v4-1-d6bbc92f12f1@bootlin.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>

drm/i915/lttpr: Enable Extended Wake Timeout

Usually retimers take around 30 to 40ms to exit all devices from
sleep state. Extended wake timeout mechanism helps to give
that additional time.

--v2
-Grant the requested time only if greater than 1ms [Arun/Jani]
-Reframe commit message [Arun]

--v3
-Move the function to drm_core [Dmitry/Jani]

Spec: DP v2.1 Section 3.6.12.3
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250122053358.1545039-4-suraj.kandpal@intel.com

drm/display/dp: Define function to setup Extended wake time

Extended wake timeout request helps to give additional
time by reading the DPCD register through which sink requests the
minimal amount of time required to wake the sink up.
Source  device shall keep retying the AUX tansaction till the
extended timeout that is being granted for LTTPRs from the
sink device.

--v2
-Add documentation [Dmitry]

Spec: DP v2.1 Section 3.6.12.3
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250122053358.1545039-3-suraj.kandpal@intel.com

drm/dp: Add the DPCD register required for Extended wake timeout

Add DPCD registers required to configure Extended Wake Timeout
for LTTPR.

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250122053358.1545039-2-suraj.kandpal@intel.com

drm/ast: Only look up VBIOS mode on full modesets

Only look up the VBIOS mode during atomic_check if the display mode
changes. For page flips, the previous settings still apply. Avoids the
runtime overhead of looking up the VBIOS mode on each page flip.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-17-tzimmermann@suse.de

drm/ast: Remove struct ast_vbios_mode_info

The type struct ast_vbios_mode_info used to store information about
the color format and display mode. It has outlived its purpose. Inline
its fields into struct ast_crtc_state and replace all instances.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-16-tzimmermann@suse.de

drm/ast: astdp: Look up mode index from table

Replace the large switch statement with a look-up table when selecting
the mode index. Makes the code easier to read. The table is sorted by
resolutions; if run-time overhead from traversal becomes significant,
binary search would be a possible optimization.

The mode index requires a refresh-rate index to be added or subtracted,
which still requires a minimal switch. In the original code, some of
the indices did not contain this computation. Those cases would have been
equivalent to adding 0, so they are now all subsumed in the switch's
default branch.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Suggested-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
v3:
- explain the semantics of the new switch statement (Jocelyn)
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-15-tzimmermann@suse.de

drm/ast: astdp: Rework display-mode setting

ASTDP requires a mode index, depending on the resolution. Move the
look-up code from ast_dp_set_mode() into a separate helper. Inline
the rest of the function into its only caller. Rename the variable
names and register constants to match the programming manual.

As before, the mode-index lookup still happens during the update's
atomic commit. Right now, there's no way of doing it during the atomic
check. The lookup requires the VBIOS mode, which is not available at
the atomic check's invocation. At least warn now if the mode index
could not be found.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-14-tzimmermann@suse.de

drm/ast: Inline ast_get_vbios_mode_info()

The helper ast_get_vbios_mode_info() retrieves hardware-specific format
and display-mode information. Inline the function into its only caller.

While at it, also replace a use of struct drm_format_info.cpp with the
correct DRM 4CC codes.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-13-tzimmermann@suse.de

drm/ast: Validate DRM display modes against VBIOS modes

Test DRM display modes against the list of modes supported by the
VBIOS. The helper will respect the supported-modes flags in struct
ast_device. Hence only DRM display modes supported by the VBIOS
will be reported; without the current duplication of this information.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-12-tzimmermann@suse.de

drm/ast: Add helpers for VBIOS mode lookup

Mode lines are independent from hardware Gen or TX chip, so hide all
VBIOS mode tables in ast_vbios.c.

Move the look-up code for VBIOS modes from ast_vbios_get_mode_info()
to ast_vbios_find_mode(). The new look-up function respects the
supported-mode flags in struct ast_device. For example, if a device
does not have struct ast_device.support_fullhd set, the helper does
not return a valid mode for 1920x1080. Taking the supported-mode flags
into account allows for making the VBIOS tables the single reference
for validating and setting display modes against hardware capabilities.

v2:
- replace mode switch with look-up table (Jocelyn)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-11-tzimmermann@suse.de

drm/ast: Add empty initializer for VBIOS modes

VBIOS mode tables are terminated by an entry with a refresh rate of
0xff. The code is hard to read and fragile to use. Therefore create
an empty entry with AST_VBIOS_MODE_INVALID to terminate each mode list.

Stop at the invalid entry when searching for modes in the tables.
Instead of testing for refresh == 0xff, test with a helper function if
the mode's size and refresh have meaningful values.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-10-tzimmermann@suse.de

drm/ast: Find VBIOS mode from regular display size

The ast driver looks up supplied display modes from an internal list of
display modes supported by the VBIOS.

Do not use the crtc_-prefixed display values from struct drm_display_mode
for looking up the VBIOS mode. The fields contain raw values that the
driver programs to hardware. They are affected by display settings like
double-scan or interlace.

Instead use the regular vdisplay and hdisplay fields for lookup. As the
programmed values can now differ from the values used for lookup, set
struct drm_display_mode.crtc_vdisplay and .crtc_hdisplay from the VBIOS
mode.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-9-tzimmermann@suse.de

drm/ast: Always validate H/V sync flags

The ast driver matches DRM display modes against an internal list of
modes supported by the VBIOS. Matching H/V sync flags between modes is
preferred, but optional. If sync flags are not matching, the driver
would program the VBIOS settings to hardware and let the display handle
the difference.

DRM modes are generated from attached displays or standard mode lines.
Therefore differences to the VBIOS modes are not just cosmetical, but
signal possible incompatibility with the display hardware.

Hence make matching H/V sync flags mandatory. If the VBIOS does not
support a certain mode, we should report it as unsupported. Note that
the VBIOS mode tables all appear to refer to standard modes.

(If sync flags really make no difference to the VBIOS, the ast driver
shouldn't match them in the first place.)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-8-tzimmermann@suse.de

drm/ast: Add support_wuxga flag to struct ast_device

Detect support for 1920x1200 (WUXGA) in ast_detect_widescreen(). The
flag is cleared by default. The test logic has been taken from existing
code in ast_crtc_helper_mode_valid(). The code in that function is being
replaced by the new flag.

v2:
- move shared detection code into helper (Jocelyn)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-7-tzimmermann@suse.de

drm/ast: Add support_fullhd flag to struct ast_device

Detect support for 1920x1080 (FullHD) in ast_detect_widescreen(). The
flag is cleared by default. The test logic has been taken from existing
code in ast_crtc_helper_mode_valid(). The code in that function is being
replaced by the new flag.

For Gen3, a new branch duplicates the Gen2 logic and adds a test for
AST2200. Gen2 adds a test for AST2100.

v2:
- use fullhd flag for setting max width/height

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-6-tzimmermann@suse.de

drm/ast: Reorganize widescreen test around hardware Gens

Testing for support of widescreen modes mixes up various hardware
Gens. First branch by hardware Gen, then do specific tests for each
Gen. By default, widesscreen support is disabled.

Later patches will add more specific tests for each Gen.

v2:
- move shared detection code into helper (Jocelyn)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-5-tzimmermann@suse.de

drm/ast: Rename support_wide_screen to support_wsxga_p

The flag support_wide_screen in struct ast_device selects devices that
support resolutions of at least 1680x1050 (WSXGA+). Name it accordingly.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-4-tzimmermann@suse.de

drm/ast: Align naming in widescreen detection code to manual

Rename variables and register constants to align with the programming
manual. Add new constants where necessary.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-3-tzimmermann@suse.de

drm/ast: Remove 1152x864 from list of widescreen resolutions

The resolution 1152x864 has a ratio of 4:3 and is already handled
as such. Remove it from the list of widescreen resolutions.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-2-tzimmermann@suse.de

accel/ivpu: Move recovery work to system_unbound_wq

Recovery work doesn't need to be bound to any specific CPU, so move it
to unbound workqueue to improve execution time and system latency.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129125636.1047413-7-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Enable recovery and adjust timeouts for fpga

Recovery now works on fpga. JSM state dump timeout needs to
be really long for the new fpga model releases.

Enable punit on fpga.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Tomasz Rusinowicz <tomasz.rusinowicz@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129125636.1047413-6-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Turn on HWS by default on all platforms

Hardware scheduling (HWS) is supposed to be supported on all existing
platform with recent FW including pre-silicon ones. Turn on HWS by
default.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129125636.1047413-5-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Fix missing MMU events if file_priv is unbound

Move the ivpu_mmu_discard_events() function to the common portion of
the abort work function. This ensures it is called only once, even if
there are no faulty contexts in context_xa, to guarantee that MMU events
are discarded and new events are not missed.

Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129125636.1047413-4-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Update last_busy in IRQ handler

Call pm_runtime_mark_last_busy() in top half of IRQ handler to prevent
device from being runtime suspended before bottom half is executed on
a workqueue.

Reviewed-by: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129125636.1047413-3-jacek.lawrynowicz@linux.intel.com

accel/ivpu: Add support for hardware fault injection

Introduces the capability to simulate hardware faults for testing
purposes. The new `fail_hw` fault can be injected in
`ivpu_hw_reg_poll_fld()`, which is used in various parts of the driver
to wait for the hardware to reach a specific state. This allows to test
failures during NPU boot and shutdown, IPC message handling and more.

Fault injection can be enabled using debugfs or a module parameter.

Reviewed-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250129125636.1047413-2-jacek.lawrynowicz@linux.intel.com

Linux 6.14-rc1