drm/i915/mtl: Support HBR3 rate with C10 phy and eDP in MTL

eDP specification supports HBR3 link rate since v1.4a. Moreover,
C10 phy can support HBR3 link rate for both DP and eDP. Therefore,
do not clamp the supported rates for eDP at 6.75Gbps.

Cc: <stable@vger.kernel.org>
BSpec: 70073 74224

Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018113622.2761997-1-chaitanya.kumar.borah@intel.com

drm/i915/display: Abstract C10/C20 pll calculation

As done with the hw readout, properly abstract the C10/C20 phy details
inside intel_cx0_phy.c.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018222831.4132968-3-lucas.demarchi@intel.com

drm/i915/display: Abstract C10/C20 pll hw readout

intel_cx0_phy.[ch] should contain the details about C10/C20, not leaking
it to the rest of the driver. Start abstracting this by exporting a
single PLL hw readout that handles the differences between C20 and C10
internally to that compilation unit.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018222831.4132968-2-lucas.demarchi@intel.com

drm/i915/lnl: Fix check for TC phy

With MTL adding PICA between the port and the real phy, the path
add for DG2 stopped being followed and newer platforms are simply using
the older path for TC phys. LNL is no different than MTL in this aspect,
so just add it to the mess. In future the phy and port designation and
deciding if it's TC should better be cleaned up.

To make it just a bit better, also change intel_phy_is_snps() to show
this is DG2-only.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026184045.1015655-3-lucas.demarchi@intel.com

drm/i915/lnl: Extend C10/C20 phy

For Lunar Lake, DDI-A is connected to C10 PHY, while TC1-TC3 are connected
to C20 phy, like in Meteor Lake. Update the check in intel_is_c10phy()
accordingly.

This reverts the change in commit e388ae97e225 ("drm/i915/display:
Eliminate IS_METEORLAKE checks") that turned that into a display engine
version check. The phy <-> port connection is very SoC-specific and not
related to that version.

IS_LUNARLAKE() is defined to 0 in i915 as it's expected that the
(upcoming) xe driver is the one defining the platform, with i915 only
driving the display side.

Bspec: 70818
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231026184045.1015655-2-lucas.demarchi@intel.com

drm/i915/sprite: move sprite_name() to intel_sprite.c

Move sprite_name() where its only user is, and convert it to a function,
removing the implicit dev_priv usage.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011202259.1090131-1-jani.nikula@intel.com

drm/i915/display: Reset message bus after each read/write operation

Every know and then we receive the following error when running
for example IGT test kms_flip.

[drm] *ERROR* PHY G Read 0d80 failed after 3 retries.
[drm] *ERROR* PHY G Write 0d81 failed after 3 retries.

Since the error is sporadic in nature, the patch proposes
to reset the message bus after every successful or unsuccessful
read or write operation.

v2: Add FIXME's to indicate the experimental nature of
    this workaround (Rodrigo)
v3: Dropping the additional delay as moving reset to *_read_once()
    and *_write_once() functions seem unnecessary delay

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231016125544.719963-1-mika.kahola@intel.com

drm/i915: remove display device info from i915 capabilities

Display device and display runtime info is exposed as part of
i915_display_capabilities debugfs entry. Remove this information
from i915_ capabilities as it is now reduntant.

Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018102723.16915-3-vinod.govindapillai@intel.com

drm/i915/display: Move enable_dp_mst under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-24-jouni.hogander@intel.com

drm/i915/display: Move nuclear_pageflip under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-23-jouni.hogander@intel.com

drm/i915/display: Move verbose_state_checks under display

v2: Change device parameter permissions to 0400

Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-22-jouni.hogander@intel.com

drm/i915/display: Use device parameters instead of module in I915_STATE_WARN

Also make module parameter as non writable.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-21-jouni.hogander@intel.com

drm/i915/display: Move disable_display parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-20-jouni.hogander@intel.com

drm/i915/display: Move force_reset_modeset_test parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-19-jouni.hogander@intel.com

drm/i915/display: Move load_detect_test parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-18-jouni.hogander@intel.com

drm/i915/display: Move enable_dpcd_backlight module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-17-jouni.hogander@intel.com

drm/i915/display: Move edp_vswing module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-16-jouni.hogander@intel.com

drm/i915/display: Move invert_brightness module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-15-jouni.hogander@intel.com

drm/i915/display: Move enable_ips module parameter under display

Move enable_ips module parameter under display and change it as boolean.

v2:
  - Change enable_ip as boolean
  - Fix copy paste error (i915_param -> intel_display_param)

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-14-jouni.hogander@intel.com

drm/i915/display: Move disable_power_well module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-13-jouni.hogander@intel.com

drm/i915/display: Move enable_sagv module parameter under display

Move enable_sagv module parameter under display and change the parameter
permissions to non-writblase (0400)

v2: Change permissions to 0400

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-12-jouni.hogander@intel.com

drm/i915/display: Move enable_dpt module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-11-jouni.hogander@intel.com

drm/i915/display: Move enable_dc module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-10-jouni.hogander@intel.com

drm/i915/display: Move vbt_sdvo_panel_type module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-9-jouni.hogander@intel.com

drm/i915/display: Move panel_use_ssc module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-8-jouni.hogander@intel.com

drm/i915/display: Move lvds_channel_mode module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-7-jouni.hogander@intel.com

drm/i915/display: Move vbt_firmware module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-6-jouni.hogander@intel.com

drm/i915/display: Move psr related module parameters under display

Move psr related module parameters under display. Also fix error in
enable_psr2_sel_fetch module parameter descrtiption. It was saying disabled
by default while it's vice versa. Also psr_safest_params was missing
default value in description. This is now added.

v2:
  - Fix enable_psr2_sel_fetch description.
  - Add default value into psr_safest_params description.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-5-jouni.hogander@intel.com

drm/i915/display: Move enable_fbc module parameter under display

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-4-jouni.hogander@intel.com

drm/i915/display: Dump also display parameters

GPU error dump contained all module parameters. If we are moving
display parameters to intel_display_params.[ch] they are not dumped
into GPU error dump. This patch is adding moved display parameters
back to GPU error dump. Display parameters are also included in
i915_capabilities

v2: Add parameters to i915_capabilities as well

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-3-jouni.hogander@intel.com

drm/i915/display: Add framework to add parameters specific to display

Currently all module parameters are handled by i915_param.c/h. This
is a problem for display parameters when Xe driver is used. Add
a mechanism to add parameters specific to the display. This is mainly
copied from i915_[debugfs]_params.[ch]. Parameters are not yet moved. This
is done by subsequent patches.

v2:
  - Drop unused predefinition (dentry)
  - Clarify need for empty INTEL_DISPLAY_PARAMS_FOR_EACH in comment

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024124109.384973-2-jouni.hogander@intel.com

drm/i915/display: debugfs entry to list display capabilities

Create a separate debugfs entry to list the display capabilities
IGT can rely on this debugfs entry for tests that depend on
display device and display runtime info for both xe and i915
drivers.

v2: rename the entry to i915_display_capabilities (Chaitanya)

Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231018102723.16915-2-vinod.govindapillai@intel.com

drm/i915: stop including i915_utils.h from intel_runtime_pm.h

Remove an unnecessary include.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011162102.1030354-1-jani.nikula@intel.com

drm/i915/aux: rename dev_priv to i915

No reason to stick to dev_priv, rename to i915.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011201533.1081368-2-jani.nikula@intel.com

drm/i915/aux: add separate register macros and functions for VLV/CHV

Add separate macros for VLV/CHV registers without the implicit dev_priv,
and with the display MMIO base baked in.

A number of implicitly used dev_priv local variables can be removed.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011201533.1081368-1-jani.nikula@intel.com

drm/i915: drop gt/intel_gt.h include from skl_universal_plane.c

No longer needed after commit 94bcf876cb6a ("drm/i915/mtl: Drop
Wa_14017240301").

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011142704.985867-1-jani.nikula@intel.com

drm/i915/display: Use intel_bo_to_drm_bo instead of obj->base

Xe and i915 objects have differing implementation. Use intel_bo_to_drm_bo
instead of obj->base as xe_bo doesn't have base pointer.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012072158.4115795-3-jouni.hogander@intel.com

drm/i915/display: Move releasing gem object away from fb tracking

As a preparation for Xe we want to remove all i915_gem_object details away
from frontbuffer tacking code. Due to this move releasing gem object
reference to i915_gem_object_set_frontbuffer.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012072158.4115795-2-jouni.hogander@intel.com

drm/i915/mtl: Remove the 'force_probe' requirement for Meteor Lake

Meteor Lake has demonstrated consistent stability for some time.
All user-space API modifications tide to its core platform
functions are operational.

The necessary firmware components are set up and comprehensive
testing has been condused over a period.

Given the recent faborable CI results, as well, we believe it's
time to eliminate the 'force_probe' prerequisite and activate the
platform by default.

Signed-off-by: Aditya Chauhan <aditya.chauhan@intel.com>
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Chris Wilson <chris.p.wilson@linux.intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Signed-off-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Lee Shawn C <shawn.c.lee@intel.com>
Tested-by: Lee Shawn C <shawn.c.lee@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231008164824.919262-1-andi.shyti@linux.intel.com

drm/i915/pci: Clean up zero initializers

Just use a simple {} to zero initialize arrays/structs instead
of the hodgepodge of stuff we are using currently.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012122442.15718-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/hdcp: Clean up zero initializers

Just use a simple {} to zero initialize arrays/structs instead
of the hodgepodge of stuff we are using currently.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012122442.15718-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/display: Clean up zero initializers

Just use a simple {} to zero initialize arrays/structs instead
of the hodgepodge of stuff we are using currently.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231012122442.15718-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/dp: Remove unused DSC caps from intel_dp

The previous patches converted all users of the DSC DPCD caps to look
these up from the connector, so remove the version stored in intel_dp.

A follow-up patchset will read out the MST connector specific
capabilities in intel_dp_add_mst_connector() ->
intel_dp_mst_read_decompression_port_dsc_caps().

v2:
- Rebased on intel_edp_get_dsc_sink_cap() addition in the patchset.
v3:
- Rebased on read-out fix for eDP in the patchset.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011171606.2540078-3-imre.deak@intel.com

drm/i915/dp_mst: Use connector DSC DPCD in intel_dp_mst_mode_valid_ctx()

Use the connector's DSC DPCD capabilities in
intel_dp_mst_mode_valid_ctx().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-19-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_dsc_compute_config()

Use the connector's DSC DPCD capabilities in
intel_dp_dsc_compute_config().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-18-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_mode_valid()

Use the connector's DSC DPCD capabilities in intel_dp_mode_valid().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-17-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_dsc_get_slice_count()

Use the connector's DSC DPCD capabilities in
intel_dp_dsc_get_slice_count().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-16-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_dsc_supports_format()

Use the connector's DSC DPCD capabilities in
intel_dp_dsc_supports_format().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-15-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_dsc_compute_params()

Use the connector's DSC DPCD capabilities in
intel_dp_dsc_compute_params().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-14-imre.deak@intel.com

drm/i915/dp: Pass only the required DSC DPCD to intel_dp_sink_dsc_version_minor()

intel_dp_sink_dsc_version_minor() only requires the DSC DPCD, so pass
only this to the function.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-13-imre.deak@intel.com

drm/i915/dp: Pass only the required i915 to intel_dp_source_dsc_version_minor()

intel_dp_source_dsc_version_minor() only requires the i915 pointer, so pass
only this to the function.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-12-imre.deak@intel.com

drm/i915/dp: Pass connector DSC DPCD to drm_dp_dsc_sink_supported_input_bpcs()

Use the connector's DSC DPCD capabilities in
drm_dp_dsc_sink_supported_input_bpcs().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-11-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_dsc_max_sink_compressed_bppx16()

Use the connector's DSC DPCD capabilities in
intel_dp_dsc_max_sink_compressed_bppx16().

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-10-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_supports_dsc()

Use the connector's DSC DPCD capabilities in intel_dp_supports_dsc().

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-9-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_supports_fec()

Use the connector's DSC DPCD capabilities in intel_dp_supports_fec().

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-8-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in intel_dp_dsc_compute_max_bpp()

Use the connector's DSC DPCD capabilities in intel_dp_dsc_compute_max_bpp()
instead of the version stored in the encoder.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-7-imre.deak@intel.com

drm/i915/dp: Use connector DSC DPCD in i915_dsc_fec_support_show()

Use the connector's DSC DPCD capabilities in i915_dsc_fec_support_show()
instead of the version stored in the encoder. Atm the two are identical,
but a follow-up patch will store the (MST) connector specific version
in the connector.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-6-imre.deak@intel.com

drm/i915/dp: Use i915/intel connector local variables in i915_dsc_fec_support_show()

Cache the i915 specific device and connector pointers in
i915_dsc_fec_support_show().

v2:
- s/Cahce/Cache typo in commit log. (Stan)

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006133727.1822579-5-imre.deak@intel.com

drm/i915/dp_mst: Set connector DSC capabilities and decompression AUX

Similarly to eDP and SST-DP connectors read out the DSC capabilities for
MST connectors as well. Atm these will match the root port's DSC caps
and only used after a follow-up change enables the decompression for
each stream separately (vs. the current way of enabling it only globally
in the first branch device downstream of the root port).

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231010112504.2156789-3-imre.deak@intel.com

drm/i915/dp: Store DSC DPCD capabilities in the connector

In an MST topology the DSC capabilities are specific to each connector,
retrieved either from the sink if it decompresses the stream, or from a
branch device between the source and the sink in case this branch device
does the decompression. Accordingly each connector needs to cache its
own DSC DPCD and FEC capabilities, along with the AUX device through
which the decompression can be enabled. This patch prepares for that by
storing the capabilities and the DSC AUX device in the connector, for
now these just matching the version stored in intel_dp. The follow-up
patches will convert all users to look up these in the connector instead
of intel_dp, after which the intel_dp copies are removed.

v2:
- Rebased on intel_edp_get_dsc_sink_cap() addition in previous patch.
v3:
- Rebased on read-out fix for eDP in previous patch.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011171606.2540078-2-imre.deak@intel.com

drm/i915/dp: Sanitize DPCD revision check in intel_dp_get_dsc_sink_cap()

Check only the eDP or the DP specific DPCD revision depending on the
sink type. Pass the corresponding revision to the function, which allows
getting the DSC caps of a branch device (in an MST topology, which has
its own DPCD and so DPCD revision).

While at it use DP_DPCD_REV_14 instead of open coding it and for clarity
add a separate function to read out the DSC capability on eDP.

v2:
- Use DP_DPCD_REV_14 instead of open coding it. (Stan)
- Check EDP_DCPD_REV/DPCD_REV in a clearer way. (Ville)
v3:
- Fix the read-out for eDP in intel_dp_detect().

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011171606.2540078-1-imre.deak@intel.com

drm/i915/dsb: Re-instate DSB for LUT updates

With all the known issues sorted out we can start to use
DSB to load the LUTs.

Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009132204.15098-3-ville.syrjala@linux.intel.com

drm/i915/dsb: Correct DSB command buffer cache coherency settings

The display engine does not snoop the caches so we should mark
the DSB command buffer as I915_CACHE_NONE.
i915_gem_object_create_internal() always gives us I915_CACHE_LLC
on LLC platforms. And to make things 100% correct we should also
clflush at the end, if necessary.

Note that currently this is a non-issue as we always write the
command buffer through a WC mapping, so a cache flush is not actually
needed. But we might actually want to consider a WB mapping since
we also end up reading from the command buffer (in the indexed
reg write handling). Either that or we should do something else
to avoid those reads (might actually be even more sensible on DGFX
since we end up reading over PCIe). But we should measure the overhead
first...

Anyways, no real harm in adding the belts and suspenders here so
that the code will work correctly regardless of how we map the
buffer. If we do get a WC mapping (as we request)
i915_gem_object_flush_map() will be a nop. Well, apart form
a wmb() which may just flush the WC buffer a bit earlier
than would otherwise happen (at the latest the mmio accesses
would trigger the WC flush).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009132204.15098-2-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915/dsb: Allocate command buffer from local memory

Using system memory for the DSB command buffer doesn't appear to work.
On DG2 it seems like the hardware internally replaces the actual memory
reads with zeroes, and so we end up executing a bunch of NOOPs instead
of whatever commands we put in the buffer. To determine that I measured
the time it takes to execute the instructions, and the results are
always more or less consistent with executing a buffer full of NOOPs
from local memory.

Another theory I considered was some kind of cache coherency issue.
Looks like i915_gem_object_pin_map_unlocked() will in fact give you a
WB mapping for system memory on DGFX regardless of what mapping mode
was requested (WC in case of the DSB code). But clflush did not
change the behaviour at all, so that theory seems moot.

On DG1 it looks like the hardware might actually be fetching data from
system memory as the logs indicate that we just get underruns. But that
is equally bad, so doesn't look like we can really use system memory on
DG1 either.

Thus always allocate the DSB command buffer from local memory on
discrete GPUs.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009132204.15098-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>

drm/i915/lnl: Remove watchdog timers for PSR

Watchdog timers for Lunarlake HW were removed for PSR/PSR2
The patch removes the use of these timers from the driver code.

BSpec: 69895

v2: Reword commit message (Ville)
    Drop HPD mask from LNL (Ville)
    Revise masking logic (Jouni)
v3: Revise commit message (Ville)
    Revert HPD mask removal as irrelevant for this patch (Ville)

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231010095233.590613-1-mika.kahola@intel.com

drm/i915: Add new DG2 PCI IDs

Add recently added PCI IDs for DG2

BSpec: 44477
Signed-off-by: Shekhar Chauhan <shekhar.chauhan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231011080039.2781048-1-shekhar.chauhan@intel.com

drm/i915/dsi: Add some debug logging to mipi_exec_i2c (v2)

Add some debug logging to mipi_exec_i2c, to make debugging various
issues seen with it easier.

Changes in v2:
- Drop unnecessary __func__ drm_dbg_kms() argument

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920195613.304091-5-hdegoede@redhat.com

drm/i915/vlv_dsi: Add DMI quirk for backlight control issues on Lenovo Yoga Tab 3 (v2)

On the Lenovo Yoga Tab 3 Pro YT3-X90F there are 2 issues with the backlight
on/off MIPI sequences:

1. The backlight on sequence has an I2C MIPI sequence element which uses
   bus 0, but there is a bogus I2cSerialBus resource under the GPU in
   the DSDT which causes i2c_acpi_find_adapter() to pick the wrong bus.

2. There is no backlight off sequence, causing the backlight to stay on.

Add a DMI quirk fixing both issues.

v2:
- Add Closes tag to gitlab issue with drm.debug=0xe, VBT info

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9380
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920195613.304091-4-hdegoede@redhat.com

drm/i915/vlv_dsi: Add DMI quirk for wrong I2C bus and panel size on Lenovo Yoga Tablet 2 series (v3)

On the Lenovo Yoga Tablet 2 830 / 1050 there are 2 problems:

1. The I2C MIPI sequence elements reference bus 3. ACPI has I2C1 - I2C7
   which under Linux become bus 0 - 6. And the MIPI sequence reference
   to bus 3 is indented for I2C3 which is bus 2 under Linux.

   This leads to errors like these:
   [  178.244049] i2c_designware 80860F41:03: controller timed out
   [  178.245703] i915 0000:00:02.0: [drm] *ERROR* Failed to xfer payload of size (1) to reg (169)
   There are 3 timeouts when the panel is on, delaying
   waking up the screen on a key press by 3 seconds.

   Note mipi_exec_i2c() cannot just subtract 1 from the bus
   given in the I2C MIPI sequence element. Since on other
   devices the I2C bus-numbers used in the MIPI sequences do
   actually start at 0.

2. width_/height_mm contain a bogus 192mm x 120mm size. This is
   especially a problem on the 8" 830 version which uses a 10:16
   portrait screen where as the bogus size is 16:10.

Add a DMI quirk to override the I2C bus and the panel size with
the correct values.

Note both the 10" 1050 models as well as the 8" 830 models use the same
mainboard and thus the same DMI strings. The 10" 1050 uses a 1920x1200
landscape screen, where as the 8" 830 uses a 1200x1920 portrait screen,
so the quirk handling uses the display resolution to detect the model.

v2:
- Also override i2c_bus_num to fix mipi_exec_i2c() timeouts

v3:
- Add Closes tag to gitlab issue with drm.debug=0xe, VBT info

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9379
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920195613.304091-3-hdegoede@redhat.com

drm/i915/vlv_dsi: Add DMI quirk for wrong panel modeline in BIOS on Asus TF103C (v3)

Vtotal is wrong in the BIOS supplied modeline for the DSI panel on
the Asus TF103C leading to the last line of the display being shown
as the first line.

Original: "1280x800": 60 67700 1280 1312 1328 1376 800 808 812 820 0x8 0xa
Fixed:    "1280x800": 60 67700 1280 1312 1328 1376 800 808 812 816 0x8 0xa

The factory installed Android has a hardcoded modeline in its kernel,
causing it to not suffer from this BIOS bug;
and the Android boot-splash which uses the EFI FB which does have this bug
has the last line all black causing the bug to not be visible.

This commit introduces a generic DMI based quirk mechanism to vlv_dsi for
doing various fixups, and uses this to correct the modeline.

v2:
- s/mode_fixup/dmi_quirk/ to make the new DMI quirk mechanism more generic
- Add a comment with the old and new modelines to the patch and commit msg

v3:
- Add Closes tag to gitlab issue with drm.debug=0xe, VBT info

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9381
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920195613.304091-2-hdegoede@redhat.com

drm/i915: Remove the module parameter 'fastboot'

By default fastboot is enabled on all Display 9+ platforms and disabled
on older platforms. Its not necessary to retain this as a module
parameter.

Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926091157.635438-1-arun.r.murthy@intel.com

drm/i915/hdcp: Move common message filling function to its own file

Create a new file intel_hdcp_gsc_message that contain functions
which fill the hdcp messages we send to gsc cs this refactor will
help us reuse code for Xe later on

--v2
-add the missed file for proper build

--v3
-use forward declarations instead of #includes [Jani]

--v4
-move linux/err.h to intel_hdcp_gsc_message.c from
intel_hdcp_gsc_message.h [Jani]

--v5
-move linux include on top of drm includes [Uma]

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009095537.653619-3-suraj.kandpal@intel.com

drm/i915/hdcp: Move checks for gsc health status

Move checks for gsc components required for HDCP 2.2
to work into intel_hdcp_gsc.c. This will also help
with XE refactor on HDCP's side.

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009095537.653619-2-suraj.kandpal@intel.com

drm/i915/display: Use correct method to free crtc_state

Even though there is no leaking of resource here lets
just use the correct method to free crtc_state

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231010183101.704439-3-suraj.kandpal@intel.com

drm/i915/display: Use intel_crtc_destroy_state instead kfree

intel_encoder_current_mode() seems to leak some resource because
it uses kfree instead of intel_crtc_destroy_state let us fix that.

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231010183101.704439-2-suraj.kandpal@intel.com

drm/i915: enable W=1 warnings by default

We enable a bunch more compiler warnings than the kernel
defaults. However, they've drifted to become a unique set of warnings,
and have increasingly fallen behind from the W=1 set.

Align with the W=1 warnings from scripts/Makefile.extrawarn for clarity,
by copy-pasting them with s/KBUILD_CFLAGS/subdir-ccflags-y/ to make it
easier to compare in the future.

Some of the -Wextra warnings do need to be disabled, just like in
Makefile.extrawarn, but take care to not disable them for W=2 or W=3
builds, depending on the warning.

v2: Add back some -Wextra warning disables (Nathan)

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
[Final s/KBUILD_CFLAGS/subdir-ccflags-y/ fix while applying]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/69a812273091b6535ddc7f9346289d71bb30f43d.1697009258.git.jani.nikula@intel.com

drm/i915: drop -Wall and related disables from cflags as redundant

The kernel top level Makefile, and recently scripts/Makefile.extrawarn,
have included -Wall, and the disables -Wno-format-security and
$(call cc-disable-warning,frame-address,) for a very long time. They're
redundant in our local subdir-ccflags-y and can be dropped.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5ab754ddc2e342c75deb8476275984918e573beb.1697009258.git.jani.nikula@intel.com

drm/i915/cx0: Only clear/set the Pipe Reset bit of the PHY Lanes Owned

Currently, with MFD/pin assignment D, the driver clears the pipe reset bit
of lane 1 which is not owned by display. This causes the display
to block S0iX.

By not clearing this bit for lane 1 and keeping whatever default, S0ix
started to work. This is already what the driver does at the end
of the phy lane reset sequence (Step#8)

Bspec: 65451
Fixes: 619a06dba6fa ("drm/i915/mtl: Reset only one lane in case of MFD")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005001310.154396-1-khaled.almahallawy@intel.com

drm/i915/gvt: move structs intel_gvt_irq_info and intel_gvt_irq_map to interrupt.c

Structs intel_gvt_irq_info and intel_gvt_irq_map are not used outside of
interrupt.c. Hide them, and reduce includes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926121904.499888-4-jani.nikula@intel.com

drm/i915/gvt: move struct engine_mmio to mmio_context.c

struct engine_mmio is not used outside of mmio_context.c. Hide it, and
reduce includes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926121904.499888-3-jani.nikula@intel.com

drm/i915/gvt: don't include gvt.h from intel_gvt_mmio_table.h

intel_gvt_mmio_table.c has no need to include the massive
gvt.h. Simplify.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926121904.499888-2-jani.nikula@intel.com

drm/i915/gvt: remove unused to_gvt() and reduce includes

gvt.h has no need to include i915_drv.h once the unused to_gvt() has
been removed.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926121904.499888-1-jani.nikula@intel.com

drm/i915/xe2lpd: update the scaler feature capability

Update the number of scalers per pipe based on the display
capabilities reported.

v1: define the field values instead of the magic number (JaniN)

Bspec: 71161
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001113155.80659-4-vinod.govindapillai@intel.com
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915/xe2lpd: update the dsc feature capability

Update the global dsc flag based on the display capabilities
reported.

v1: define the field values instead of the magic number (JaniN)

Bspec: 71161
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001113155.80659-3-vinod.govindapillai@intel.com
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915/xe2lpd: display capability register definitions

Register definitions to track the reported scalable display
feature configurations

Bspec: 71161
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001113155.80659-2-vinod.govindapillai@intel.com
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915: Add wrapper for getting display step

Add a wrapper around intel_step_name that takes in driver data as an
argument. This wrapper will help maintain compatibility with the
proposed xe driver.

Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231003065211.1052385-1-chaitanya.kumar.borah@intel.com

drm/i915/display: Free crtc_state in verify_crtc_state

Free hw_crtc_state in verify_crtc_state after we are done using
this or else it's just a resource leak.

Fixes: 2745bdda2095 ("drm/i915: Stop clobbering old crtc state during state check")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231010053208.691260-1-suraj.kandpal@intel.com

drm/i915: Fix VLV color state readout

VLV was missed when the color.get_config() hook was added.
Remedy that.

Not really sure what the final plan here was since a bunch of
color related readout was left in intel_display.c anyway,
but that's for anothr day to figure out...

Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: 9af09dfcdfa1 ("drm/i915/color: move pre-SKL gamma and CSC enable read to intel_color")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009145828.12960-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/uapi: fix doc typos

Correct typo of "its".
Add commas for clarity.
Capitalize L3.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231008214942.28439-1-rdunlap@infradead.org

drm/i915/ddi: Remove redundant intel_connector NULL check

Remove redundant intel_connector NULL check. Having it here just
creates further confusion and also the variable already gets
dereferenced before the aforementioned NULL check

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231006072830.581487-1-suraj.kandpal@intel.com

drm/i915: s/dev_priv/i915/ in the state checker

Switch the state checker over to using the new 'i915' variable
name insteda of the old 'dev_priv'.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/pipe_config/crtc_state/ in the state checker

Switch over to the modern variable naming in the state checker.
Ie. rename the pipe_config stuff to crtc_state.

Also make it clear which is the "software state" (ie. what the
current state should be) vs. "hardware state" (ie. what the
currnet state really is).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Simplify the state checker calling convetions

We're passing in a totally random mismash of things into the state
checker. Clean it up to pass in the minimum needed.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Constify remainder of the state checker

Mark the remaining crtc states used by the state checker as const.
There is no reason to ever mutate them here.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Simplify snps/c10x DPLL state checker calling convetion

Passing in the atomic state + crtc state is a bit weird. The latter
can be just the crtc (which is the normal calling convention used
in a lot of other places).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Constify the snps/c10x PLL state checkers

State checkers should never modify the crtc states, so make
them const.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Simplify watermark state checker calling convention

There is never any reason to pass in both the crtc and its state
as one can always dig out the crtc from its state. But for more
consistency across the whole state checker let's just pass the
overall atomic state+crtc here as well.

v2: Also pass state+crtc here (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005122713.3531-1-ville.syrjala@linux.intel.com

drm/i915: Constify watermark state checker

The skl+ wm state checker has no reason to modify the crtc state,
so make it const.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Simplify DPLL state checker calling convention

Make life simpler by just passing in the atomic state + crtc
instead of plumbing in all kinds of crtc states.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Constify the crtc states in the DPLL checker

The DPLL state checker should not be modifying the crtc states,
so make the const.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231004155607.7719-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>