Hans Verkuil [Thu, 31 Aug 2017 08:12:55 +0000 (04:12 -0400)]
media: tc358743: add CEC support
Add CEC support for the tc358743 HDMI-CSI bridge.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Thu, 31 Aug 2017 08:12:54 +0000 (04:12 -0400)]
media: tc358743_regs.h: add CEC registers
Add the missing CEC register defines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Wed, 28 Jun 2017 08:14:15 +0000 (04:14 -0400)]
media: MAINTAINERS: add cec-gpio entry
Add an entry for the CEC GPIO driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Wed, 28 Jun 2017 08:14:28 +0000 (04:14 -0400)]
media: cec-gpio: add HDMI CEC GPIO driver
Add a simple HDMI CEC GPIO driver that sits on top of the cec-pin framework.
While I have heard of SoCs that use the GPIO pin for CEC (apparently an
early RockChip SoC used that), the main use-case of this driver is to
function as a debugging tool.
By connecting the CEC line to a GPIO pin on a Raspberry Pi 3 for example
it turns it into a CEC debugger and protocol analyzer.
With 'cec-ctl --monitor-pin' the CEC traffic can be analyzed.
But of course it can also be used with any hardware project where the
HDMI CEC line is hooked up to a pull-up gpio line.
In addition this has (optional) support for tracing HPD changes if the
HPD is connected to a GPIO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Wed, 2 Aug 2017 07:22:33 +0000 (03:22 -0400)]
media: dt-bindings: document the CEC GPIO bindings
Document the bindings for the cec-gpio module for hardware where the
CEC line and optionally the HPD line are connected to GPIO lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Wed, 30 Aug 2017 16:05:55 +0000 (12:05 -0400)]
media: cec-ioc-dqevent.rst: document new CEC_EVENT_PIN_HPD_LOW/HIGH events
Document these new CEC events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Tue, 15 Aug 2017 14:07:25 +0000 (10:07 -0400)]
media: cec: add CEC_EVENT_PIN_HPD_LOW/HIGH events
Add support for two new low-level events: PIN_HPD_LOW and PIN_HPD_HIGH.
This is specifically meant for use with the upcoming cec-gpio driver
and makes it possible to trace when the HPD pin changes. Some HDMI
sinks do strange things with the HPD and this makes it easy to debug
this.
Note that this also moves the initialization of a devnode mutex and
list to the allocate_adapter function: if the HPD is high, then as
soon as the HPD interrupt is created an interrupt occurs and
cec_queue_pin_hpd_event() is called which requires that the devnode
mutex and list are initialized.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Mon, 18 Sep 2017 09:23:57 +0000 (05:23 -0400)]
media: cec-core.rst/cec-ioc-receive.rst: clarify CEC_TX_STATUS_ERROR
CEC_TX_STATUS_ERROR can be used if the HW cannot tell LOST_ARB and
LOW_DRIVE apart, or when some other error occurs. It is not a
replacement for NACK.
So the hardware must be able to tell the difference between OK, NACK and
'something else'.
Clarify the documentation (both public and kernel API) on this point.
Also fix two small typos (this messages -> this message).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Mon, 18 Sep 2017 10:26:03 +0000 (06:26 -0400)]
media: cec-ioc-dqevent.rst: fix typo
The documentation talked about INITIAL_VALUE when the actual define is
INITIAL_STATE.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Fri, 1 Sep 2017 08:37:54 +0000 (04:37 -0400)]
media: cec-pin.c: use proper ktime accessor functions
Use ktime_to_ns/ns_to_ktime. This makes it possible to work with older kernels
and the media_build compatibility system.
For the mainline kernel these functions are NOPs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jose Abreu [Thu, 14 Sep 2017 15:23:38 +0000 (11:23 -0400)]
media: cec: Respond to unregistered initiators, when applicable
Running CEC 1.4 compliance test we get the following error on test
11.1.6.2: "ERROR: The DUT did not broadcast a
<Report Physical Address> message to the unregistered device."
Fix this by letting GIVE_PHYSICAL_ADDR message respond to unregistered
device. Also, GIVE_DEVICE_VENDOR_ID and GIVE_FEATURES fall in the
same category so, respond also to these messages.
With this fix we pass CEC 1.4 official compliance.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hans Verkuil [Thu, 31 Aug 2017 16:56:10 +0000 (12:56 -0400)]
media: s5p-cec: add NACK detection support
The s5p-cec driver returned CEC_TX_STATUS_ERROR for the NACK condition.
Some digging into the datasheet uncovered the S5P_CEC_TX_STAT1 register where
bit 0 indicates if the transmit was nacked or not.
Use this to return the correct CEC_TX_STATUS_NACK status to userspace.
This was the only driver that couldn't tell a NACK from another error, and
that was very unusual. And a potential problem for applications as well.
Tested with my Odroid-U3.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Laurent Pinchart [Wed, 30 Aug 2017 17:14:36 +0000 (13:14 -0400)]
media: staging/imx: Fix uninitialized variable warning
The ret variable can be returned uninitialized in the
imx_media_create_pad_vdev_lists() function is imxmd->num_vdevs is zero.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colin Ian King [Tue, 29 Aug 2017 10:21:10 +0000 (06:21 -0400)]
media: qcom: camss: Make function vfe_set_selection static
The function vfe_set_selection is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
warning: symbol 'vfe_set_selection' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stanimir Varbanov [Tue, 29 Aug 2017 08:19:43 +0000 (04:19 -0400)]
media: venus: init registered list on streamoff
Add missing init_list_head for the registered buffer list.
Absence of the init could lead to a unhandled kernel paging
request as below, when streamon/streamoff are called in row.
[338046.571321] Unable to handle kernel paging request at virtual address
fffffffffffffe00
[338046.574849] pgd =
ffff800034820000
[338046.582381] [
fffffffffffffe00] *pgd=
00000000b60f5003[338046.582545]
, *pud=
00000000b1f31003
, *pmd=
0000000000000000[338046.592082]
[338046.597754] Internal error: Oops:
96000004 [#1] PREEMPT SMP
[338046.601671] Modules linked in: venus_enc venus_dec venus_core
usb_f_ecm g_ether usb_f_rndis u_ether libcomposite ipt_MASQUERADE
nf_nat_masquerade_ipv4 arc4 wcn36xx mac80211 btqcomsmd btqca iptable_nat
nf_co]
[338046.662408] CPU: 0 PID: 5433 Comm: irq/160-venus Tainted: G W
4.9.39+ #232
[338046.668024] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[338046.675268] task:
ffff80003541cb00 task.stack:
ffff800026e20000
[338046.682097] PC is at venus_helper_release_buf_ref+0x28/0x88
[venus_core]
[338046.688282] LR is at vdec_event_notify+0xe8/0x150 [venus_dec]
[338046.695029] pc : [<
ffff000000af6c48>] lr : [<
ffff000000a6fc60>]
pstate:
a0000145
[338046.701256] sp :
ffff800026e23bc0
[338046.708494] x29:
ffff800026e23bc0 x28:
0000000000000000
[338046.718853] x27:
ffff000000afd4f8 x26:
ffff800031faa700
[338046.729253] x25:
ffff000000afd790 x24:
ffff800031faa618
[338046.739664] x23:
ffff800003e18138 x22:
ffff800002fc9810
[338046.750109] x21:
ffff800026e23c28 x20:
0000000000000001
[338046.760592] x19:
ffff80002a13b800 x18:
0000000000000010
[338046.771099] x17:
0000ffffa3d01600 x16:
ffff000008100428
[338046.781654] x15:
0000000000000006 x14:
ffff000089045ba7
[338046.792250] x13:
ffff000009045bb6 x12:
00000000004f37c8
[338046.802894] x11:
0000000000267211 x10:
0000000000000000
[338046.813574] x9 :
0000000000032000 x8 :
00000000dc400000
[338046.824274] x7 :
0000000000000000 x6 :
ffff800031faa728
[338046.835005] x5 :
ffff80002a13b850 x4 :
0000000000000000
[338046.845793] x3 :
fffffffffffffdf8 x2 :
0000000000000000
[338046.856602] x1 :
0000000000000003 x0 :
ffff80002a13b800
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Sat, 2 Sep 2017 11:42:42 +0000 (07:42 -0400)]
media: dvb: i2c transfers over usb cannot be done from stack
Since commit
29d2fef8be11 ("usb: catch attempts to submit urbs
with a vmalloc'd transfer buffer"), the AverMedia AverTV DVB-T
USB 2.0 (a800) fails to probe.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Arnd Bergmann [Tue, 5 Sep 2017 07:13:20 +0000 (09:13 +0200)]
media: leds: as3645a: add V4L2_FLASH_LED_CLASS dependency
We get a link error when V4L2_FLASH_LED_CLASS=m and AS3645A is built-in:
drivers/leds/leds-as3645a.o: In function `as3645a_v4l2_setup':
leds-as3645a.c:(.text+0x258): undefined reference to `v4l2_flash_init'
leds-as3645a.c:(.text+0x284): undefined reference to `v4l2_flash_indicator_init'
leds-as3645a.c:(.text+0x2a4): undefined reference to `v4l2_flash_release'
drivers/leds/leds-as3645a.o: In function `as3645a_remove':
leds-as3645a.c:(.text+0x784): undefined reference to `v4l2_flash_release'
This adds the same Kconfig dependency that the other V4L2 flash
drivers in drivers/leds use, to avoid that broken configuration.
Fixes:
a56ba8fbcb55 ("media: leds: as3645a: Add LED flash class driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Tue, 5 Sep 2017 12:23:42 +0000 (08:23 -0400)]
media: get rid of removed DMX_GET_CAPS and DMX_SET_SOURCE leftovers
Those two ioctls were never used within the Kernel. Still, there
used to have compat32 code there (and an if #0 block at the core).
Get rid of them.
Fixes:
286fe1ca3fa1 ("media: dmx.h: get rid of DMX_GET_CAPS")
Fixes:
13adefbe9e56 ("media: dmx.h: get rid of DMX_SET_SOURCE")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rob Herring [Thu, 20 Jul 2017 22:06:22 +0000 (18:06 -0400)]
media: Revert "[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay"
This reverts commit
d2180e0cf77dc7a7049671d5d57dfa0a228f83c1.
The commit was flawed in that if the device_node pointers are different,
then in fact a different device is present and the device node could be
different in ways other than full_name.
As Frank Rowand explained:
"When an overlay (1) is removed, all uses and references to the nodes and
properties in that overlay are no longer valid. Any driver that uses any
information from the overlay _must_ stop using any data from the overlay.
Any driver that is bound to a new node in the overlay _must_ unbind. Any
driver that became bound to a pre-existing node that was modified by the
overlay (became bound after the overlay was applied) _must_ adjust itself
to account for any changes to that node when the overlay is removed. One
way to do this is to unbind when notified that the overlay is about to
be removed, then to re-bind after the overlay is completely removed.
If an overlay (2) is subsequently applied, a node with the same
full_name as from overlay (1) may exist. There is no guarantee
that overlay (1) and overlay (2) are the same overlay, even if
that node has the same full_name in both cases."
Also, there's not sufficient overlay support in mainline to actually
remove and re-apply an overlay to hit this condition as overlays can
only be applied from in kernel APIs.
Fixes:
d2180e0cf77d ("[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay")
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sergei A. Trusov [Wed, 2 Aug 2017 08:00:01 +0000 (04:00 -0400)]
media: staging: atomisp: sh_css_calloc shall return a pointer to the allocated space
The calloc function returns either a null pointer or a pointer to the
allocated space. Add the second case that is missed.
Fixes:
da22013f7df4 ("atomisp: remove indirection from sh_css_malloc")
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Fri, 4 Aug 2017 14:12:03 +0000 (10:12 -0400)]
media: Revert "[media] lirc_dev: remove superfluous get/put_device() calls"
This reverts commit
5be2b76a9ca4ea5fd3e221114d62eeb0d78267ca.
Only when the lirc device is freed, should we drop our reference to
rc_dev, else we the rc_dev is freed to early. If userspace has
a file descriptor open during unplug, it goes bang.
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x7bb/0x1e10
Read of size 8 at addr
ffff8801d7d61ed0 by task ir-rec/2609
-snip-
mutex_lock_nested+0x1b/0x20
? mutex_lock_nested+0x1b/0x20
rc_close.part.6+0x20/0x60 [rc_core]
rc_close+0x13/0x20 [rc_core]
lirc_dev_fop_close+0x62/0xd0 [lirc_dev]
__fput+0x236/0x410
? fput+0xb0/0xb0
? do_raw_spin_trylock+0x110/0x110
? set_rq_offline.part.70+0xa0/0xa0
____fput+0xe/0x10
task_work_run+0x116/0x180
? task_work_cancel+0x170/0x170
? _raw_spin_unlock+0x27/0x40
? switch_task_namespaces+0x5f/0x90
do_exit+0x68b/0xe80
Cc: stable@vger.kernel.org # For Kernel 4.13
Fixes:
5be2b76a9ca4 ("[media] lirc_dev: remove superfluous get/put_device() calls")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Tue, 5 Sep 2017 11:06:40 +0000 (07:06 -0400)]
media: add qcom_camss.rst to v4l-drivers rst file
Avoid this warning:
/devel/v4l/docs/Documentation/media/v4l-drivers/qcom_camss.rst:: WARNING: document isn't included in any toctree
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Tue, 5 Sep 2017 11:02:44 +0000 (07:02 -0400)]
media: dvb headers: make checkpatch happier
Adjust dvb ca.h, dmx.h and frontend.h in order to make
checkpatch happier. Now, it only complains about the typedefs,
and those are there just to provide backward userspace
compatibility.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Tue, 5 Sep 2017 10:47:08 +0000 (06:47 -0400)]
media: dvb uapi: move frontend legacy API to another part of the book
There's a chapter for the legacy APIs. Move the frontend DVBv3
API to it, and update the chapter's introduction accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Mon, 4 Sep 2017 20:37:30 +0000 (16:37 -0400)]
media: pixfmt-srggb12p.rst: better format the table for PDF output
Adjust the table to be better displayed on PDF output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sakari Ailus [Sun, 3 Sep 2017 20:12:33 +0000 (16:12 -0400)]
media: docs-rst: media: Don't use \small for V4L2_PIX_FMT_SRGGB10 documentation
There appears to be an issue in using \small in certain cases on Sphinx
1.4 and 1.5. Other format documents don't use \small either, remove it
from here as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[mchehab@s-opensource.com: kept tabularcolumns - readjusted - and
add a few blank lines for it to display better]
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 18:39:51 +0000 (14:39 -0400)]
media: index.rst: don't write "Contents:" on PDF output
Right now, Sphinx unconditionally creates a blank page with
just "Contents:" on it, on PDF output. While this makes sense
for html, it doesn't o PDF, as LaTeX does what's required
automatically.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 11:04:33 +0000 (07:04 -0400)]
media: pixfmt*.rst: replace a two dots by a comma
On several tables, the color sample location table preamble is
written as:
Color Sample Location..
Instead of:
Color Sample Location:
I suspect that the repetition of such pattern was due to some
copy-and-paste (or perhaps some error during DocBook conversion).
Anyway, fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 09:46:06 +0000 (05:46 -0400)]
media: vidioc-g-fmt.rst: adjust table format
While doing a visual inspection with Sphinx 1.5, I noticed that
one of the columns was smaller than the text written there.
As this is the only thing I noticed with Sphinx 1.5, I suspect
that this was also a problem with Sphinx 1.4. Yet, I opted to
touch it in a way that wouldn't cause backward issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 09:44:19 +0000 (05:44 -0400)]
media: vivid.rst: add a blank line to correct ReST format
On all vivid parameters, there's an space after the parameter,
except for "DV Timings Signal Mode". That makes this single one
to be written in bold, and, at PDF output, at the same line as
its description.
Use the same convention as the other parameters, in order to
adjust its output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 09:13:22 +0000 (05:13 -0400)]
media: v4l2 uapi book: get rid of driver programming's chapter
It doesn't make any sense having a driver programming's chapter
at the uAPI book, as this is related to kernel API. Also,
we now have such kAPI book where V4L2 driver programming is covered.
So, get rid of this left-over.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 09:10:44 +0000 (05:10 -0400)]
media: format.rst: use the right markup for important notes
There's an important note there, but it is not using the
ReST markup. So, it doesn't get any visual highlight on
the output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 02:08:13 +0000 (22:08 -0400)]
media: docs-rst: cardlists: change their format to flat-tables
Most tables there don't fit on 80 columns. Some are very big.
While those tables are actually generated via scripts, every
time a new board is added, the entire table could be reformatted.
>From the diffstat PoV, that's bad, as it is hard to see what
happened.
One such example is at changeset
4868f6e1fce6 ("media:
em28xx-cardlist.rst: update to reflect last changes"):
The USB ID for "Plextor ConvertX PX-AV100U" was added to card
number 9, with caused the entire table to be reformatted.
So, instead, use flat-tables. While here, fix PDF output,
by adding tablecolumns to the tables that need it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 02:07:20 +0000 (22:07 -0400)]
media: em28xx-cardlist.rst: update to reflect last changes
There were some new board additions. Update the cardlist
accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 01:28:51 +0000 (21:28 -0400)]
media: v4l2-event.rst: adjust table to fit on PDF output
The tables there don't quite fit on PDF output.
Adjust it by adding a tabularcolumns macro.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 00:25:36 +0000 (20:25 -0400)]
media: docs: don't show ToC for each part on PDF output
The "Table of Contents" of a PDF file is generated only once,
at the beginning fo the output. It doesn't produce it on
each part.
So, don't output this text on each part of the document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sun, 3 Sep 2017 00:02:42 +0000 (20:02 -0400)]
media: cec uapi: Adjust table sizes for PDF output
Several tables at this media book chapter have issues
when PDF is produced. Adjust them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 23:29:53 +0000 (19:29 -0400)]
media: mc uapi: adjust some table sizes for PDF output
Some cells are too small to fit the text written to it.
Increase it. No text changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 22:59:25 +0000 (18:59 -0400)]
media: rc-sysfs-nodes.rst: better use literals
A literal box provides a better visual when pdf and html output
is generated for things like the output of a sysfs devnode.
It alsod matches other conventions used within the media book.
So, use it.
While here, use literals for protocol names.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 21:46:52 +0000 (17:46 -0400)]
media: docs: fix PDF build with Sphinx 1.4
Commit
70b074df4ed1 ("media: fix pdf build with Spinx 1.6") caused
a regression at Sphinx 1.4 PDF build: although it produces a full
document in batch mode, it returns errors on interactive mode:
[63]
Runaway argument?
{\relax
! Paragraph ended before \multicolumn was complete.
<to be read again>
\par
l.7703 \hline\end{tabulary}
The error seems to be due to some bug at Sphinx PDF output:
when multicolumns is used, it doesn't accept an empty string.
Just removing the :cpan:`1` and replacing by two empty
columns fix the issue.
Fixes:
70b074df4ed1 ("media: fix pdf build with Spinx 1.6")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 20:50:45 +0000 (16:50 -0400)]
media: v4l uAPI docs: adjust some tables for PDF output
On tests with Spinx 1.4, some tables are still writing text
outside cells. Adjust those tables.
PS.: As this was revisited several times, I suspect that this
will only be fully fixed if we add tabularcolumns to all tables
at the V4L2 part of the book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 20:48:28 +0000 (16:48 -0400)]
media: vidioc-g-tuner.rst: Fix table number of cols
The Tuner Audio Matrix table is broken: the first row has 7
columns instead of 6, causing it to be parsed wrong and displayed
very badly on PDF output.
Fix it and adjust the table to look nice at PDF output
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 20:32:15 +0000 (16:32 -0400)]
media: vidioc-querycap: use a more realistic value for KERNEL_VERSION
In the past, V4L2 versions were 0.x.y, but that changed years
ago. Since Kernel 3.1, however, the numbering schema was changed
to match the Kernel version.
However, the presented example still uses the old numerating
schema, with is a misleading information.
So, update it to the new schema.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Sat, 2 Sep 2017 13:54:48 +0000 (09:54 -0400)]
media: v4l uAPI: add descriptions for arguments to all ioctls
Several ioctls are missing descriptions for the third argument
of the ioctl() command. They should have a description, as
otherwise the output won't be ok, and will sound like something
is missing.
So, add them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Mon, 4 Sep 2017 12:03:40 +0000 (08:03 -0400)]
media: ca.h: document ca_msg and the corresponding ioctls
Usually, CA messages are sent/received via reading/writing at
the CA device node. However, two drivers (dst_ca and firedtv-ci)
also implement it via ioctls.
Apparently, on both cases, the net result is the same.
Anyway, let's document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Mon, 4 Sep 2017 00:50:17 +0000 (20:50 -0400)]
media: ca docs: document CA_SET_DESCR ioctl and structs
The av7110 driver uses CA_SET_DESCR to store the descrambler
control words at the CA descrambler slots.
Document it.
Thanks-to: Honza Petrouš <jpetrous@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 19:45:47 +0000 (15:45 -0400)]
media: net.h: add kernel-doc and use it at Documentation/
As we did with frontend.h, ca.h and dmx.h, move the struct
definition to net.h.
That should help to keep it updated, as more stuff gets
added there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 19:05:28 +0000 (15:05 -0400)]
media: frontend.h: Avoid the term DVB when doesn't refer to a delivery system
The DVB term can either refer to the subsystem or to a delivery
system. Avoid it in the first case at the kernel-doc markups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 18:44:31 +0000 (14:44 -0400)]
media: intro.rst: don't assume audio and video codecs to be MPEG2
Originally, when DVB was introduced, all codecs would be part of
MPEG2 standard. That's not true anymore, as there are a large
number of codec standards used on digital TV nowadays.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 18:14:48 +0000 (14:14 -0400)]
media: dvbstb.svg: use dots for the optional parts of the hardware
The hardware description mentions that some parts are optional.
Make it clearer at the drawing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 17:44:28 +0000 (13:44 -0400)]
media: dmx-get-pes-pids.rst: document the ioctl
This ioctl is supported by the DVB core, but was never
documented.
Add a documentation for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:21:49 +0000 (12:21 -0400)]
media: dvb uAPI docs: minor editorial changes
Do minor editorial changes to improve documentation readability:
- mark literals as such;
- add table markups to hint sizes;
- define what PES means;
- instead of hardcoding devnode numbers to zero (like adapter0/) use a
question mark, to indicate that multiple devnodes may exist;
- add cross-references where useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:32:44 +0000 (12:32 -0400)]
media: dvbapi.rst: add an entry to DVB revision history
There are several missing items at the API history. Yet,
as we're doing a significant change there, add a new entry.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:31:43 +0000 (12:31 -0400)]
media: dvb-frontend-parameters.rst: fix the name of a struct
The struct that contains an union of DVB parameters is
called dvb_frontend_parameters (and not FrontendParameters).
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:30:16 +0000 (12:30 -0400)]
media: dmx-fread.rst: specify how DMX_CHECK_CRC works
In the past, the documentation used to say that, if a CRC error
was found, a "-ECRC" error would be returned. That's not true:
the DVB core will just silently ignore such errors.
So, add an explicit note about that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:28:16 +0000 (12:28 -0400)]
media: dvb uAPI docs: Prefer use "Digital TV instead of "DVB"
The usage of the term "DVB" at the dvb API docs is confusing,
as, right now, it can refer to either the European digital TV
standard or to the subsystem.
So, prefer calling it as "Digital TV" on most places, to avoid
ambiguity.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:23:17 +0000 (12:23 -0400)]
media: ca-fopen.rst: Fixes the device node name for CA
The device node name for CA is wrong since ever. I suspect
that the name there was before DVBv3 (with was the first API
introduced at the Kernel).
Anyway, use the right name there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:15:43 +0000 (12:15 -0400)]
media: dvb uAPI docs: adjust return value ioctl descriptions
There are several issues on the return value for ioctls:
- Text is confusing;
- Some error codes don't exist;
- The non-generic error codes should come before the text
that points to the generic error codes;
- Tables don't contain column size hints;
- Some references are not marked as such.
Correct them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:20:12 +0000 (12:20 -0400)]
media: gen-errors.rst: document ENXIO error code
This error can be produced at least at the DVB subsystem.
As it is generic enough, document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 16:19:17 +0000 (12:19 -0400)]
media: gen-errors.rst: remove row number comments
Those are introduced by the conversion scripts and don't
really help. Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 14:02:23 +0000 (10:02 -0400)]
media: dvb uapi docs: better organize header files
Instead of having one chapter per file, place all of them at
the same chapter. That better organize the chapters at the uAPI
documentation.
As a side effect, now all uAPI headers are at the same page,
at the html output, with makes easier to use it as a reference
index for the spec.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 13:18:02 +0000 (09:18 -0400)]
media: dst_ca: remove CA_SET_DESCR boilerplate
This ioctl is not implemented at dst_ca driver. There's just
a boilerplate code there. Remove it, as it is unlikely that
anyone would implement it those days.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 12:53:11 +0000 (08:53 -0400)]
media: dvb rst: identify the documentation gap at the API
Now that DVB spec is almost in sync, document what's missing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 12:45:28 +0000 (08:45 -0400)]
media: dvb CA docs: place undocumented data together with ioctls
Right now, the same undocumented structs are on two places:
at ca_data_types.rst and together with their ioctls.
Move them to just one place and use the standard way to
represent them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 12:39:43 +0000 (08:39 -0400)]
media: ca-get-descr-info.rst: document this ioctl
Instead of a generic boilerplate, fill it with relevant
information about this ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 12:32:56 +0000 (08:32 -0400)]
media: ca-get-slot-info.rst: document this ioctl
Instead of a generic boilerplate, fill it with relevant
information about this ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 12:07:46 +0000 (08:07 -0400)]
media: ca-get-cap.rst: document this ioctl
Instead of a generic boilerplate, fill it with relevant
information about this ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 11:59:59 +0000 (07:59 -0400)]
media: ca-reset.rst: add some description to this ioctl
While we don't have any documentation for it, based on what's
there at Kaffeine and VDR, it seems that this command should
be issued before start using CA. So, document it as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 12:21:04 +0000 (08:21 -0400)]
media: dst_ca: return a proper error code from CA errors
Right now, on several places, the driver is returning a
"-1" error to userspace, instead of a proper error code.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 11:48:02 +0000 (07:48 -0400)]
media: ca.h: document most CA data types
For most of the stuff there, documenting is easy, as the
header file contains information.
Yet, I was unable to document two data structs:
ca_msg and ca_descr
As those two structs are used by a few drivers, keep them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 11:41:49 +0000 (07:41 -0400)]
media: ca.h: get rid of CA_SET_PID
This ioctl seems to be some attempt to support a feature
at the bt8xx dst_ca driver. Yet, as said there, it
"needs more work". Right now, the code there is just
a boilerplate.
At the end of the day, no driver uses this ioctl, nor it is
documented anywhere (except for "needs more work").
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 23:34:02 +0000 (19:34 -0400)]
media: net.rst: Fix the level of a section of the net chapter
Due to a mistake, the DVB net chapter was actually broken
into two different chapters. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 16:28:52 +0000 (12:28 -0400)]
media: dmx.h: add kernel-doc markups and use it at Documentation/
The demux documentation is pretty poor nowadays: most of the
structs and enums aren't documented at all.
Add proper kernel-doc markups for them and use it.
Now, the demux API data structures are fully documented :-)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 23:09:06 +0000 (19:09 -0400)]
media: dmx.h: get rid of GET_DMX_EVENT
This seems to be a pure fictional API :-)
It only exists at the DVB book, with no code implemeting it.
So, just get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 18:21:43 +0000 (14:21 -0400)]
media: dmx.h: get rid of DMX_SET_SOURCE
No driver uses this ioctl, nor it is documented anywhere.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 18:11:34 +0000 (14:11 -0400)]
media: dmx.h: get rid of DMX_GET_CAPS
There's no driver currently using it; it is also not
documented about what it would be supposed to do.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 16:52:45 +0000 (12:52 -0400)]
media: dmx.h: get rid of unused DMX_KERNEL_CLIENT
There's a flag defined for Digital TV demux that is not used
anywhere, called DMX_KERNEL_CLIENT. Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 11:17:21 +0000 (07:17 -0400)]
media: fe_property_parameters.rst: better document bandwidth
Use a table to document the supported bandwidths. That makes
it clearer to readers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Thu, 31 Aug 2017 11:16:17 +0000 (07:16 -0400)]
media: fe_property_parameters.rst: better define properties usage
Several frontend properties are specific to a subset of the
delivery systems. Make it clearer when describing each
property.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 17:45:20 +0000 (13:45 -0400)]
media: dvb frontend docs: use kernel-doc documentation
Now that frontend.h contains most documentation for the frontend,
remove the duplicated information from Documentation/ and use the
kernel-doc auto-generated one instead.
That should simplify maintainership of DVB frontend uAPI, as most
of the documentation will stick with the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 12:12:38 +0000 (08:12 -0400)]
media: dvb/frontend.h: document the uAPI file
Most of the stuff at the Digital TV frontend header file
are documented only at the Documentation. However, a few
kernel-doc markups are there, several of them with parsing
issues.
Add the missing documentation, copying definitions from the
Documentation when it applies, fixing some bugs.
Please notice that DVBv3 stuff that were deprecated weren't
commented by purpose. Instead, they were clearly tagged as
such.
This patch prepares to move part of the documentation from
Documentation/ to kernel-doc comments.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 11:55:47 +0000 (07:55 -0400)]
media: dvb/frontend.h: move out a private internal structure
struct dtv_cmds_h is just an ancillary struct used by the
dvb_frontend.c to internally store frontend commands.
It doesn't belong to the userspace header, nor it is used anywhere,
except inside the DVB core. So, remove it from the header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 09:25:20 +0000 (05:25 -0400)]
media: dvb/intro: adjust the notices about optional hardware
Both CA and decoders are optional. Also, the presence or
absence has nothing to do on being a PCI card or not.
Nowadays, most hardware leaves the decoders to either the
GPU or to some ISP inside the SoC, instead of implementing
it inside the Digital TV part of the device.
So, change the wording to reflect the hardware changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 09:20:45 +0000 (05:20 -0400)]
media: dvb/intro: update the history part of the document
Convergence doesn't exist anymore. The community itself maintains
the spec. Update accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 09:19:25 +0000 (05:19 -0400)]
media: dvb/intro: update references for TV standards
The references there are only for DVB. Add missing references for
ATSC and ISDB standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Wed, 30 Aug 2017 09:15:40 +0000 (05:15 -0400)]
media: dvb/intro: use the term Digital TV to refer to the system
On several places at the introduction, a digital TV board and its
kernel support is called as DVB. The reason is simple: by the
time the document was written, there were no other digital TV
standards :-)
Modernize the specs by referring to them as Digital TV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 10:09:14 +0000 (06:09 -0400)]
media: dmx.h: split typedefs from structs
Using typedefs inside the Kernel is against CodingStyle, and
there's no good usage here.
Just like we did at frontend.h, at commit
0df289a209e0
("[media] dvb: Get rid of typedev usage for enums"), let's keep
those typedefs only to provide userspace backward compatibility.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab [Fri, 1 Sep 2017 09:43:39 +0000 (05:43 -0400)]
media: ca.h: split typedefs from structs
Using typedefs inside the Kernel is against CodingStyle, and
there's no good usage here.
Just like we did at frontend.h, at commit
0df289a209e0 ("[media] dvb:
Get rid of typedev usage for enums"), let's keep those typedefs only
to provide userspace backward compatibility.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Wed, 23 Aug 2017 15:06:04 +0000 (11:06 -0400)]
media: serial_ir: fix tx timing calculation on 32-bit
Move the calculation to where it is needed, so the result doesn't
need to be stored in the device struct.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sean Young [Fri, 25 Aug 2017 14:45:47 +0000 (10:45 -0400)]
media: rc: gpio-ir-tx: use ktime accessor functions
Prefer using accessor functions so we are not dependent on the ktime_t
type.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Jasmin Jessich [Fri, 25 Aug 2017 09:59:41 +0000 (05:59 -0400)]
media: rc: use ktime accessor functions
Prefer using accessor functions so we are not dependent on the ktime_t
type.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fabio Estevam [Sun, 27 Aug 2017 16:30:35 +0000 (12:30 -0400)]
media: max2175: Propagate the real error on devm_clk_get() failure
When devm_clk_get() fails we should return the real error code
instead of always returning -ENODEV.
This allows defer probe to happen in the case the clock provider has
not been enabled by the time max2175 driver gets probed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Matthias Schwarzott [Sun, 27 Aug 2017 12:26:07 +0000 (08:26 -0400)]
media: cx23885: Explicitly list Hauppauge model numbers of HVR-4400 and HVR-5500
Add two new model numbers to suppress this message in kernel log:
cx23885: cx23885[0]: warning: unknown hauppauge model #121029
Add these model numbers:
* Model 121019 - WinTV-HVR4400
* Model 121029 - WinTV-HVR5500
For WinTV-HVR4400 the documentation and my hardware differ:
Documentation says it supports DVB-S/S2 and DVB-T,
but my hardware also supports DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Javier Martinez Canillas [Wed, 9 Aug 2017 09:37:30 +0000 (05:37 -0400)]
media: i2c: adv748x: Export I2C device table entries as module aliases
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, and the driver is only exporting the OF ID
table entries as module aliases.
So if the driver is built as module, autoload won't work since udev/kmod
won't be able to match the registered OF device with its driver module.
Before this patch:
$ modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
After this patch:
modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
alias: i2c:adv7482
alias: i2c:adv7481
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Arnd Bergmann [Mon, 7 Aug 2017 10:49:18 +0000 (06:49 -0400)]
media: staging/imx: always select VIDEOBUF2_DMA_CONTIG
I ran into a rare build error during randconfig testing:
drivers/staging/media/imx/imx-media-capture.o: In function `capture_stop_streaming':
imx-media-capture.c:(.text+0x224): undefined reference to `vb2_buffer_done'
drivers/staging/media/imx/imx-media-capture.o: In function `imx_media_capture_device_register':
imx-media-capture.c:(.text+0xe60): undefined reference to `vb2_queue_init'
imx-media-capture.c:(.text+0xfa0): undefined reference to `vb2_dma_contig_memops'
While VIDEOBUF2_DMA_CONTIG was already selected by the camera driver,
it wasn't necessarily there with just the base driver enabled.
This moves the 'select' statement to the top-level option to make
sure it's always available.
Fixes:
64b5a49df486 ("[media] media: imx: Add Capture Device Interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bhumika Goyal [Thu, 3 Aug 2017 10:00:32 +0000 (06:00 -0400)]
media: dw2102: make dvb_usb_device_description structures const
dvb_usb_device_description structures are only used during a copy
operation. Therefore, declare them as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Olli Salonen [Sun, 30 Jul 2017 12:34:49 +0000 (08:34 -0400)]
media: mn88473: reset stream ID reg if no PLP given
If the PLP given is NO_STREAM_ID_FILTER (~0u) don't try to set that into the PLP register. Set PLP to 0 instead.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Olli Salonen [Sun, 30 Jul 2017 12:34:48 +0000 (08:34 -0400)]
media: mn88472: reset stream ID reg if no PLP given
If the PLP given is NO_STREAM_ID_FILTER (~0u) don't try to set that into the PLP register. Set PLP to 0 instead.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colin Ian King [Fri, 21 Jul 2017 16:01:00 +0000 (12:01 -0400)]
media: dvb_frontend: initialize variable s with FE_NONE instead of 0
GIT_AUTHOR_NAME=Colin King
GIT_AUTHOR_EMAIL=colin.king@canonical.com
In a previous commit, we added FE_NONE as an unknown fe_status.
Initialize variable s to FE_NONE instead of the more opaque value 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colin Ian King [Fri, 21 Jul 2017 16:12:38 +0000 (12:12 -0400)]
media: docs-next: update the fe_status documentation for FE_NONE
Recently added FE_NONE to the enum fe_status, so update the
documentation accordingly.
[mchehab@s-opensource.com: change description to actually
reflect what FE_NONE means: no lock of any kind]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>