ARM: dts: imx6ul: Remove fsl,anatop from usbotg1

fsl,anatop should only be added to the usbphy nodes.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6ull: fix pinctrl node name

pinctrl node name must be either pinctrl or pinmux.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx1-apf9328: Fix Ethernet node name

Per davicom,dm9000.yaml, the Ethernet node name should be 'ethernet'.

Change it to fix the following schema warning:

imx1-apf9328.dtb: eth@4,c00000: $nodename:0: 'eth@4,c00000' does not match '^ethernet(@.*)?$'
from schema $id: http://devicetree.org/schemas/net/davicom,dm9000.yaml#

Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx28-evk: Use 'eeprom' as the node name

Per at24.yaml, the node name should be 'eeprom'.

Change it accordingly to fix the following schema warning:

imx28-evk.dtb: at24@51: $nodename:0: 'at24@51' does not match '^eeprom@[0-9a-f]{1,2}$'
from schema $id: http://devicetree.org/schemas/eeprom/at24.yaml#

Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: ls1021a: Enable usb3-lpm-capable for usb3 node

Enable USB3 HW LPM feature.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6dl-yapp4: Move the internal switch PHYs under the switch node

We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.

The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.

Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.

With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")

The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.

To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.

Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address

This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.

Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6ul: Set macaddress location in ocotp

If a bootloader does not configure the MAC address, devices come up with
a random MAC at the moment.

ocotp provides registers for storing the mac-address.
Configure those for i.MX6UL and i.MX6ULL allows net/core to retrieve it from
there.

Signed-off-by: Manuel Traut <manuel.traut@mt.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx53-qsb: add support for the HDMI expander

Add support for the MCIMXHDMICARD expansion card attached to the iMX53
QSB / QSRB platforms. This enables HDMI output on those devices.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6ull-dhcom: Remove /omit-if-no-ref/ from node usdhc1-pwrseq

Remove /omit-if-no-ref/ from node usdhc1-pwrseq, because if the compile
flag -@ (include symbols) is used the node will always be there. In this
case, GPIO H is not released and therefore cannot be used. Therefore,
remove this node manually from the corresponding devicetree file and
don't rely on /omit-if-no-ref/.

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx: Add support for Apalis Evaluation Board v1.2

Add support for the new Apalis Evaluation Board v1.2. Because
only the imx6q-apalis-eval.dts was available, the imx6q-apalis-eval.dtsi
has been created which has common hardware configurations for v1.0, v1.1
and v1.2. Both imx6q-apalis-eval.dts and imx6q-apalis-eval-v1.2.dts
files include imx6q-apalis-eval.dtsi.

Versions 1.0 and 1.1 are compatible with each other and should
use imx6q-apalis-eval.dts file. Now for v1.2, the new device-tree file
should be used.

Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6: skov: add aliases for all ethernet nodes

Add aliases for all ethernet nodes including the switch. It makes it
easier to find this nodes by the boot loader.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6qdl-hummingboard: Add rtc0 and rtc1 aliases to fix hctosys

HummingBoard has two RTCs, first integrated within SoC that can be used to
wake up from sleep - and a second on the carrier board including back-up
battery which is intended for keeping time during power-off.

Add aliases for both, ensuring that the battery-backed clock is primary
rtc and used by default during boot for restoring system time.

Fixes keeping time across power-cycle observed on Debian,
which sets RTC_HCTOSYS_DEVICE="rtc0".

Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6dl: Add support for Sielaff i.MX6 Solo board

The Sielaff i.MX6 Solo board is used as controller and user interface
in vending machines. It is based on the i.MX6 Solo SoC and features
the following peripherals and interfaces:

* 512 MB DDR3 RAM
* 512 MB NAND Flash
* 1 MB NOR Flash
* SD card
* Debug LED
* Debug UART
* Key Inputs
* RTC
* RS232
* 100 MBit Ethernet
* USB Hub
* USB OTG
* HDMI
* 7" LVDS IPS panel
* PWM Backlight
* Optional Extension Board with USB Ethernet NIC

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6ul: Add missing #thermal-sensor-cells to tempmon

Fixes the dtbs_check warning:
  tempmon: '#thermal-sensor-cells' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6sl-tolino-shine2hd: fix touchscreen rotation

The display is in landscape orientation, but the touchscreen is in portrait
orientation. Specify that properly in the devicetree.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx6ull-dhcor: Remove 900MHz operating point

Due to CPU lifetime consideration of the SoC manufacturer [1] and
the preferred area of operation in the industrial related
environment, set the maximum frequency for each DHCOM i.MX6ULL to
792MHz, as with the industrial type. This is done by removing the
operating point at 900MHz and set the clock-frequency to 792000000.

[1] https://www.nxp.com/docs/en/application-note/AN5337.pdf

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: Fix PMIC v33 rail voltage range

regulator-*-microvolt is not the range the regulator supports, but the
range which the regulator is allowed to configure. Limit v33 rail to
3.3V only.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Add missing vcc supply to i2c devices

Fixes the warnings:
pca953x 1-0020: supply vcc not found, using dummy regulator
lm75 0-0049: supply vs not found, using dummy regulator

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: Add missing vcc supply to i2c eeproms

Fixes the warnings:
at24 0-0050: supply vcc not found, using dummy regulator
at24 0-0056: supply vcc not found, using dummy regulator

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7d-mba7: Remove USB OTG related properties on USB node

These properties are only used on USB OTG/DR devices, remove them from
a host only device.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: rename node for SE97BTP

temperature-sensor is the recommended node name and its main purpose.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: mark system data eeprom as read-only

This is manufacturer data and shall not be modified.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: remove superfluous status property

SDMA is enabled by default, so remove the status property.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: restrict usdhc interface modes

USDHC3 is directly connected to an eMMC, so disable other interface modes.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: restrict usdhc interface modes

USDHC1 is directly connected to an SD card, so disable other interface modes.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: Fix iomuxc node names

The node name must end with 'grp'

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Fix iomuxc node names

The node name must end with 'grp'

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: fix EEPROM compatible for SE97BTP

0x56 is the EEPROM component of SE97BTP.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Add i2c bus recovery

Add the pin muxing and GPIO settings for SCL/SDA for i2c2 & i2c3.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7: Add i2c bus recovery

Add the pin muxing and GPIO settings for SCL/SDA for i2c1.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Add SPI1_SS0 as chip select 3

ECSPI1.SS0 was missing in the list.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Add RTC aliases

Ensure the RTC devices are numbered correctly.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Enable SNVS power key

This allows using S10 for power down / shutdown.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-mba7: Mark gpio-buttons as wakeup-source

I2C expander is capable of generating an IRQ during powersave, so the
attached buttons can be used for waking up the system.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7[d]-mba7: hog Mini PCIe signals

PCIE_DIS & PCIE_RST (correctly named W_DISABLE# & PERST#) affect USB
devices as well. So hog them to make USB devices attached to Mini PCIe
connector available, despite PCIe being disabled.
Supply voltages are enabled unconditionally.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7[d]-mba7: disable PCIe interface

Using internal PHY refclk is not supported yet.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7[d]-mba7: disable USB OC on USB host and USB OTG2

USB host is an HSIC interface directly connected to a USB hub. USB OTG2
is a direct connection to Mini PCIe interface without any OC signaling.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7[d]-mba7: Move ethernet PHY reset into PHY node

Split pinctrl as well. 'reset-deassert-us' is added with a small safe
margin.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ARM: dts: imx7-tqma7/mba7: convert fsl,pins to uint32-matrix

make dtbs_check does not warn about this anymore, but bindings mandate
a uint32-matrix.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Linux 6.8-rc1

Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Merge tag 'timers-core-2024-01-21' of git://git./linux/kernel/git/tip/tip

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Merge tag 'powerpc-6.8-2' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

bcachefs: Improve inode_to_text()

Add line breaks - inode_to_text() is now much easier to read.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: logged_ops_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: reflink_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs; extents_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: ec_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: subvolume_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: snapshot_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: alloc_background_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: xattr_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: dirent_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: inode_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs; quota_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: sb-counters_format.h

bcachefs_format.h has gotten too big; let's do some organizing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: counters.c -> sb-counters.c

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: comment bch_subvolume

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch_snapshot::btime

Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: add missing __GFP_NOWARN

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: opts->compression can now also be applied in the background

The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Prep work for variable size btree node buffers

bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.

And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.

Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: grab s_umount only if snapshotting

When I was testing mongodb over bcachefs with compression,
there is a lockdep warning when snapshotting mongodb data volume.

$ cat test.sh
prog=bcachefs

$prog subvolume create /mnt/data
$prog subvolume create /mnt/data/snapshots

while true;do
    $prog subvolume snapshot /mnt/data /mnt/data/snapshots/$(date +%s)
    sleep 1s
done

$ cat /etc/mongodb.conf
systemLog:
  destination: file
  logAppend: true
  path: /mnt/data/mongod.log

storage:
  dbPath: /mnt/data/

lockdep reports:
[ 3437.452330] ======================================================
[ 3437.452750] WARNING: possible circular locking dependency detected
[ 3437.453168] 6.7.0-rc7-custom+ #85 Tainted: G            E
[ 3437.453562] ------------------------------------------------------
[ 3437.453981] bcachefs/35533 is trying to acquire lock:
[ 3437.454325] ffffa0a02b2b1418 (sb_writers#10){.+.+}-{0:0}, at: filename_create+0x62/0x190
[ 3437.454875]
               but task is already holding lock:
[ 3437.455268] ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.456009]
               which lock already depends on the new lock.

[ 3437.456553]
               the existing dependency chain (in reverse order) is:
[ 3437.457054]
               -> #3 (&type->s_umount_key#48){.+.+}-{3:3}:
[ 3437.457507]        down_read+0x3e/0x170
[ 3437.457772]        bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.458206]        __x64_sys_ioctl+0x93/0xd0
[ 3437.458498]        do_syscall_64+0x42/0xf0
[ 3437.458779]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.459155]
               -> #2 (&c->snapshot_create_lock){++++}-{3:3}:
[ 3437.459615]        down_read+0x3e/0x170
[ 3437.459878]        bch2_truncate+0x82/0x110 [bcachefs]
[ 3437.460276]        bchfs_truncate+0x254/0x3c0 [bcachefs]
[ 3437.460686]        notify_change+0x1f1/0x4a0
[ 3437.461283]        do_truncate+0x7f/0xd0
[ 3437.461555]        path_openat+0xa57/0xce0
[ 3437.461836]        do_filp_open+0xb4/0x160
[ 3437.462116]        do_sys_openat2+0x91/0xc0
[ 3437.462402]        __x64_sys_openat+0x53/0xa0
[ 3437.462701]        do_syscall_64+0x42/0xf0
[ 3437.462982]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.463359]
               -> #1 (&sb->s_type->i_mutex_key#15){+.+.}-{3:3}:
[ 3437.463843]        down_write+0x3b/0xc0
[ 3437.464223]        bch2_write_iter+0x5b/0xcc0 [bcachefs]
[ 3437.464493]        vfs_write+0x21b/0x4c0
[ 3437.464653]        ksys_write+0x69/0xf0
[ 3437.464839]        do_syscall_64+0x42/0xf0
[ 3437.465009]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.465231]
               -> #0 (sb_writers#10){.+.+}-{0:0}:
[ 3437.465471]        __lock_acquire+0x1455/0x21b0
[ 3437.465656]        lock_acquire+0xc6/0x2b0
[ 3437.465822]        mnt_want_write+0x46/0x1a0
[ 3437.465996]        filename_create+0x62/0x190
[ 3437.466175]        user_path_create+0x2d/0x50
[ 3437.466352]        bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.466617]        __x64_sys_ioctl+0x93/0xd0
[ 3437.466791]        do_syscall_64+0x42/0xf0
[ 3437.466957]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.467180]
               other info that might help us debug this:

[ 3437.469670] 2 locks held by bcachefs/35533:
               other info that might help us debug this:

[ 3437.467507] Chain exists of:
                 sb_writers#10 --> &c->snapshot_create_lock --> &type->s_umount_key#48

[ 3437.467979]  Possible unsafe locking scenario:

[ 3437.468223]        CPU0                    CPU1
[ 3437.468405]        ----                    ----
[ 3437.468585]   rlock(&type->s_umount_key#48);
[ 3437.468758]                                lock(&c->snapshot_create_lock);
[ 3437.469030]                                lock(&type->s_umount_key#48);
[ 3437.469291]   rlock(sb_writers#10);
[ 3437.469434]
                *** DEADLOCK ***

[ 3437.469670] 2 locks held by bcachefs/35533:
[ 3437.469838]  #0: ffffa0a02ce00a88 (&c->snapshot_create_lock){++++}-{3:3}, at: bch2_fs_file_ioctl+0x1e3/0xc90 [bcachefs]
[ 3437.470294]  #1: ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.470744]
               stack backtrace:
[ 3437.470922] CPU: 7 PID: 35533 Comm: bcachefs Kdump: loaded Tainted: G            E      6.7.0-rc7-custom+ #85
[ 3437.471313] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 3437.471694] Call Trace:
[ 3437.471795]  <TASK>
[ 3437.471884]  dump_stack_lvl+0x57/0x90
[ 3437.472035]  check_noncircular+0x132/0x150
[ 3437.472202]  __lock_acquire+0x1455/0x21b0
[ 3437.472369]  lock_acquire+0xc6/0x2b0
[ 3437.472518]  ? filename_create+0x62/0x190
[ 3437.472683]  ? lock_is_held_type+0x97/0x110
[ 3437.472856]  mnt_want_write+0x46/0x1a0
[ 3437.473025]  ? filename_create+0x62/0x190
[ 3437.473204]  filename_create+0x62/0x190
[ 3437.473380]  user_path_create+0x2d/0x50
[ 3437.473555]  bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.473819]  ? lock_acquire+0xc6/0x2b0
[ 3437.474002]  ? __fget_files+0x2a/0x190
[ 3437.474195]  ? __fget_files+0xbc/0x190
[ 3437.474380]  ? lock_release+0xc5/0x270
[ 3437.474567]  ? __x64_sys_ioctl+0x93/0xd0
[ 3437.474764]  ? __pfx_bch2_fs_file_ioctl+0x10/0x10 [bcachefs]
[ 3437.475090]  __x64_sys_ioctl+0x93/0xd0
[ 3437.475277]  do_syscall_64+0x42/0xf0
[ 3437.475454]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.475691] RIP: 0033:0x7f2743c313af
======================================================

In __bch2_ioctl_subvolume_create(), we grab s_umount unconditionally
and unlock it at the end of the function. There is a comment
"why do we need this lock?" about the lock coming from
commit 42d237320e98 ("bcachefs: Snapshot creation, deletion")
The reason is that __bch2_ioctl_subvolume_create() calls
sync_inodes_sb() which enforce locked s_umount to writeback all dirty
nodes before doing snapshot works.

Fix it by read locking s_umount for snapshotting only and unlocking
s_umount after sync_inodes_sb().

Signed-off-by: Su Yue <glass.su@suse.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: kvfree bch_fs::snapshots in bch2_fs_snapshots_exit

bch_fs::snapshots is allocated by kvzalloc in __snapshot_t_mut.
It should be freed by kvfree not kfree.
Or umount will triger:

[  406.829178 ] BUG: unable to handle page fault for address: ffffe7b487148008
[  406.830676 ] #PF: supervisor read access in kernel mode
[  406.831643 ] #PF: error_code(0x0000) - not-present page
[  406.832487 ] PGD 0 P4D 0
[  406.832898 ] Oops: 0000 [#1] PREEMPT SMP PTI
[  406.833512 ] CPU: 2 PID: 1754 Comm: umount Kdump: loaded Tainted: G           OE      6.7.0-rc7-custom+ #90
[  406.834746 ] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[  406.835796 ] RIP: 0010:kfree+0x62/0x140
[  406.836197 ] Code: 80 48 01 d8 0f 82 e9 00 00 00 48 c7 c2 00 00 00 80 48 2b 15 78 9f 1f 01 48 01 d0 48 c1 e8 0c 48 c1 e0 06 48 03 05 56 9f 1f 01 <48> 8b 50 08 48 89 c7 f6 c2 01 0f 85 b0 00 00 00 66 90 48 8b 07 f6
[  406.837810 ] RSP: 0018:ffffb9d641607e48 EFLAGS: 00010286
[  406.838213 ] RAX: ffffe7b487148000 RBX: ffffb9d645200000 RCX: ffffb9d641607dc4
[  406.838738 ] RDX: 000065bb00000000 RSI: ffffffffc0d88b84 RDI: ffffb9d645200000
[  406.839217 ] RBP: ffff9a4625d00068 R08: 0000000000000001 R09: 0000000000000001
[  406.839650 ] R10: 0000000000000001 R11: 000000000000001f R12: ffff9a4625d4da80
[  406.840055 ] R13: ffff9a4625d00000 R14: ffffffffc0e2eb20 R15: 0000000000000000
[  406.840451 ] FS:  00007f0a264ffb80(0000) GS:ffff9a4e2d500000(0000) knlGS:0000000000000000
[  406.840851 ] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  406.841125 ] CR2: ffffe7b487148008 CR3: 000000018c4d2000 CR4: 00000000000006f0
[  406.841464 ] Call Trace:
[  406.841583 ]  <TASK>
[  406.841682 ]  ? __die+0x1f/0x70
[  406.841828 ]  ? page_fault_oops+0x159/0x470
[  406.842014 ]  ? fixup_exception+0x22/0x310
[  406.842198 ]  ? exc_page_fault+0x1ed/0x200
[  406.842382 ]  ? asm_exc_page_fault+0x22/0x30
[  406.842574 ]  ? bch2_fs_release+0x54/0x280 [bcachefs]
[  406.842842 ]  ? kfree+0x62/0x140
[  406.842988 ]  ? kfree+0x104/0x140
[  406.843138 ]  bch2_fs_release+0x54/0x280 [bcachefs]
[  406.843390 ]  kobject_put+0xb7/0x170
[  406.843552 ]  deactivate_locked_super+0x2f/0xa0
[  406.843756 ]  cleanup_mnt+0xba/0x150
[  406.843917 ]  task_work_run+0x59/0xa0
[  406.844083 ]  exit_to_user_mode_prepare+0x197/0x1a0
[  406.844302 ]  syscall_exit_to_user_mode+0x16/0x40
[  406.844510 ]  do_syscall_64+0x4e/0xf0
[  406.844675 ]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[  406.844907 ] RIP: 0033:0x7f0a2664e4fb

Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bios must be 512 byte algined

Fixes: 023f9ac9f70f bcachefs: Delete dio read alignment check
Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: remove redundant variable tmp

The variable tmp is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so tmp can be
removed.

Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the enclosing
expression, the value is never actually read from 'ret'
[deadcode.DeadStores]

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Improve trace_trans_restart_relock

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Fix excess transaction restarts in __bchfs_fallocate()

drop_locks_do() should not be used in a fastpath without first trying
the do in nonblocking mode - the unlock and relock will cause excessive
transaction restarts and potentially livelocking with other threads that
are contending for the same locks.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: extents_to_bp_state

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bkey_and_val_eq()

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Better journal tracepoints

Factor out bch2_journal_bufs_to_text(), and use it in the
journal_entry_full() tracepoint; when we can't get a journal reservation
we need to know the outstanding journal entry sizes to know if the
problem is due to excessive flushing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Print size of superblock with space allocated

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Avoid flushing the journal in the discard path

When issuing discards, we may need to flush the journal if there's too
many buckets that can't be discarded until a journal flush.

But the heuristic was bad; we should be comparing the number of buckets
that need to flushes against the number of free buckets, not the number
of buckets we saw.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Improve move_extent tracepoint

Also print out the data_opts, so that we can see what specifically is
being done to an extent.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Add missing bch2_moving_ctxt_flush_all()

This fixes a bug with rebalance IOs getting stuck with reads completed,
but writes never being issued.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Re-add move_extent_write tracepoint

It appears this was accidentally deleted at some point - also, do a bit
of cleanup.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_kthread_io_clock_wait() no longer sleeps until full amount

Drop t he loop in bch2_kthread_io_clock_wait(): this allows the code
that uses it to be woken up for other reasons, and fixes a bug where
rebalance wouldn't wake up when a scan was requested.

This raises the possibility of spurious wakeups, but callers should
always be able to handle that reasonably well.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Add .val_to_text() for KEY_TYPE_cookie

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Don't pass memcmp() as a pointer

Some (buggy!) compilers have issues with this.

Fixes: https://github.com/koverstreet/bcachefs/issues/625
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Merge tag 'header_cleanup-2024-01-20' of https://evilpiepirate.org/git/bcachefs

Pull header fix from Kent Overstreet:
 "Just one small fixup for the RT build"

* tag 'header_cleanup-2024-01-20' of https://evilpiepirate.org/git/bcachefs:
  spinlock: Fix failing build for PREEMPT_RT

bcachefs: Reduce would_deadlock restarts

We don't have to take locks in any particular ordering - we'll make
forward progress just fine - but if we try to stick to an ordering, it
can help to avoid excessive would_deadlock transaction restarts.

This tweaks the reflink path to take extents btree locks in the right
order.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_trans_account_disk_usage_change()

The disk space accounting rewrite is splitting out accounting for each
replicas set - those are moving to btree keys, instead of percpu
counters.

This breaks bch2_trans_fs_usage_apply() up, splitting out the part we
will still need.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch_fs_usage_base

Split out base filesystem usage into its own type; prep work for
breaking up bch2_trans_fs_usage_apply().

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_prt_compression_type()

bounds checking helper, since compression types are extensible

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: helpers for printing data types

We need bounds checking since new versions may introduce new data types.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: BTREE_TRIGGER_ATOMIC

Add a new flag to be explicit about when we're running atomic triggers.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: drop to_text code for obsolete bps in alloc keys

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: eytzinger_for_each() declares loop iter

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Don't log errors if BCH_WRITE_ALLOC_NOWAIT

Previously, we added logging in the write path to ensure that any
unexpected errors getting reported to userspace have a log message; but
BCH_WRITE_ALLOC_NOWAIT is a special case, it's used for promotes where
errors are expected and not reported out to userspace - so we need to
silence those.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: fix memleak in bch2_split_devs

The pointer dev_name can be modified by strseq(),
then causes the memleak:

unreferenced object 0xffff9d08a2916c80 (size 32):
  comm "mount.bcachefs", pid 9090, jiffies 4295856224 (age 17.564s)
  hex dump (first 32 bytes):
    2f 64 65 76 2f 6d 61 70 70 65 72 2f 74 65 73 74  /dev/mapper/test
    2d 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00  -0..............
  backtrace:
    [<00000000c5d3be7d>] __kmem_cache_alloc_node+0x1f3/0x2c0
    [<0000000052215d26>] __kmalloc_node_track_caller+0x51/0x150
    [<0000000069fea956>] kstrdup+0x32/0x60
    [<000000000877fcf1>] bch2_split_devs+0x3f/0x150 [bcachefs]
    [<000000007ee93204>] bch2_mount+0xcb/0x640 [bcachefs]
    [<000000002dd1e04b>] legacy_get_tree+0x30/0x60
    [<000000006afc31d3>] vfs_get_tree+0x28/0xf0
    [<000000007b0c538e>] path_mount+0x475/0xb60
    [<0000000092de5882>] __x64_sys_mount+0x105/0x140
    [<0000000054fc05d8>] do_syscall_64+0x42/0xf0
    [<00000000df584910>] entry_SYSCALL_64_after_hwframe+0x6e/0x76

Fix it by copy pointer dev_name at beginning and free the copied
pointer at end.

Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Merge tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6

Pull smb client updates from Steve French:
 "Various smb client fixes, including multichannel and for SMB3.1.1
  POSIX extensions:

   - debugging improvement (display start time for stats)

   - two reparse point handling fixes

   - various multichannel improvements and fixes

   - SMB3.1.1 POSIX extensions open/create parsing fix

   - retry (reconnect) improvement including new retrans mount parm, and
     handling of two additional return codes that need to be retried on

   - two minor cleanup patches and another to remove duplicate query
     info code

   - two documentation cleanup, and one reviewer email correction"

* tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update iface_last_update on each query-and-update
  cifs: handle servers that still advertise multichannel after disabling
  cifs: new mount option called retrans
  cifs: reschedule periodic query for server interfaces
  smb: client: don't clobber ->i_rdev from cached reparse points
  smb: client: get rid of smb311_posix_query_path_info()
  smb: client: parse owner/group when creating reparse points
  smb: client: fix parsing of SMB3.1.1 POSIX create context
  cifs: update known bugs mentioned in kernel docs for cifs
  cifs: new nt status codes from MS-SMB2
  cifs: pick channel for tcon and tdis
  cifs: open_cached_dir should not rely on primary channel
  smb3: minor documentation updates
  Update MAINTAINERS email address
  cifs: minor comment cleanup
  smb3: show beginning time for per share stats
  cifs: remove redundant variable tcon_exist

Merge tag 'dmaengine-fix-6.8-rc1' of git://git./linux/kernel/git/vkoul/dmaengine

Pull dmaengine updates from Vinod Koul:
 "New support:
   - Loongson LS2X APB DMA controller
   - sf-pdma: mpfs-pdma support
   - Qualcomm X1E80100 GPI dma controller support

  Updates:
   - Xilinx XDMA updates to support interleaved DMA transfers
   - TI PSIL threads for AM62P and J722S and cfg register regions
     description
   - axi-dmac Improving the cyclic DMA transfers
   - Tegra Support dma-channel-mask property
   - Remaining platform remove callback returning void conversions

 Driver fixes for:
   - Xilinx xdma driver operator precedence and initialization fix
   - Excess kernel-doc warning fix in imx-sdma xilinx xdma drivers
   - format-overflow warning fix for rz-dmac, sh usb dmac drivers
   - 'output may be truncated' fix for shdma, fsl-qdma and dw-edma
     drivers"

* tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (58 commits)
  dmaengine: dw-edma: increase size of 'name' in debugfs code
  dmaengine: fsl-qdma: increase size of 'irq_name'
  dmaengine: shdma: increase size of 'dev_id'
  dmaengine: xilinx: xdma: Fix kernel-doc warnings
  dmaengine: usb-dmac: Avoid format-overflow warning
  dmaengine: sh: rz-dmac: Avoid format-overflow warning
  dmaengine: imx-sdma: fix Excess kernel-doc warnings
  dmaengine: xilinx: xdma: Fix initialization location of desc in xdma_channel_isr()
  dmaengine: xilinx: xdma: Fix operator precedence in xdma_prep_interleaved_dma()
  dmaengine: xilinx: xdma: statify xdma_prep_interleaved_dma
  dmaengine: xilinx: xdma: Workaround truncation compilation error
  dmaengine: pl330: issue_pending waits until WFP state
  dmaengine: xilinx: xdma: Implement interleaved DMA transfers
  dmaengine: xilinx: xdma: Prepare the introduction of interleaved DMA transfers
  dmaengine: xilinx: xdma: Add transfer error reporting
  dmaengine: xilinx: xdma: Add error checking in xdma_channel_isr()
  dmaengine: xilinx: xdma: Rework xdma_terminate_all()
  dmaengine: xilinx: xdma: Ease dma_pool alignment requirements
  dmaengine: xilinx: xdma: Add necessary macro definitions
  dmaengine: xilinx: xdma: Get rid of unused code
  ...

Merge tag 'coccinelle-for-6.8' of git://git./linux/kernel/git/jlawall/linux

Pull coccinelle updates from Julia Lawall:
 "Updates to the device_attr_show semantic patch to reflect the new
  guidelines of the Linux kernel documentation.

  The problem was identified by Li Zhijian <lizhijian@fujitsu.com>, who
  proposed an initial fix"

* tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  coccinelle: device_attr_show: simplify patch case
  coccinelle: device_attr_show: Adapt to the latest Documentation/filesystems/sysfs.rst

media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)

This patch replaces max(a, min(b, c)) by clamp(b, a, c) in the solo6x10
driver.  This improves the readability and more importantly, for the
solo6x10-p2m.c file, this reduces on my system (x86-64, gcc 13):

 - the preprocessed size from 121 MiB to 4.5 MiB;

 - the build CPU time from 46.8 s to 1.6 s;

 - the build memory from 2786 MiB to 98MiB.

In fine, this allows this relatively simple C file to be built on a
32-bit system.

Reported-by: Jiri Slaby <jirislaby@gmail.com>
Closes: https://lore.kernel.org/lkml/18c6df0d-45ed-450c-9eda-95160a2bbb8e@gmail.com/
Cc: <stable@vger.kernel.org> # v6.7+
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: David Laight <David.Laight@ACULAB.COM>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coccinelle: device_attr_show: simplify patch case

Replacing the final expression argument by ... allows the format
string to have multiple arguments.

It also has the advantage of allowing the change to be recognized as
a change in a single statement, thus avoiding adding unneeded braces.

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>

execve: open the executable file before doing anything else

No point in allocating a new mm, counting arguments and environment
variables etc if we're just going to return ENOENT.

This patch does expose the fact that 'do_filp_open()' that execve() uses
is still unnecessarily expensive in the failure case, because it
allocates the 'struct file *' early, even if the path lookup (which is
heavily optimized) fails.

So that remains an unnecessary cost in the "no such executable" case,
but it's a separate issue.  Regardless, I do not want to do _both_ a
filename_lookup() and a later do_filp_open() like the origin patch by
Josh Triplett did in [1].

Reported-by: Josh Triplett <josh@joshtriplett.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/lkml/5c7333ea4bec2fad1b47a8fa2db7c31e4ffc4f14.1663334978.git.josh@joshtriplett.org/
Link: https://lore.kernel.org/lkml/202209161637.9EDAF6B18@keescook/
Link: https://lore.kernel.org/lkml/CAHk-=wgznerM-xs+x+krDfE7eVBiy_HOam35rbsFMMOwvYuEKQ@mail.gmail.com/
Link: https://lore.kernel.org/lkml/CAHk-=whf9qLO8ipps4QhmS0BkM8mtWJhvnuDSdtw5gFjhzvKNA@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'riscv-for-linus-6.8-mw4' of git://git./linux/kernel/git/riscv/linux

Pull more RISC-V updates from Palmer Dabbelt:

 - Support for tuning for systems with fast misaligned accesses.

 - Support for SBI-based suspend.

 - Support for the new SBI debug console extension.

 - The T-Head CMOs now use PA-based flushes.

 - Support for enabling the V extension in kernel code.

 - Optimized IP checksum routines.

 - Various ftrace improvements.

 - Support for archrandom, which depends on the Zkr extension.

 - The build is no longer broken under NET=n, KUNIT=y for ports that
   don't define their own ipv6 checksum.

* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
  lib: checksum: Fix build with CONFIG_NET=n
  riscv: lib: Check if output in asm goto supported
  riscv: Fix build error on rv32 + XIP
  riscv: optimize ELF relocation function in riscv
  RISC-V: Implement archrandom when Zkr is available
  riscv: Optimize hweight API with Zbb extension
  riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
  samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
  riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
  riscv: ftrace: Make function graph use ftrace directly
  riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
  lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
  riscv: Restrict DWARF5 when building with LLVM to known working versions
  riscv: Hoist linker relaxation disabling logic into Kconfig
  kunit: Add tests for csum_ipv6_magic and ip_fast_csum
  riscv: Add checksum library
  riscv: Add checksum header
  riscv: Add static key for misaligned accesses
  asm-generic: Improve csum_fold
  RISC-V: selftests: cbo: Ensure asm operands match constraints
  ...

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI updates from James Bottomley:
 "Final round of fixes that came in too late to send in the first
  request.

  It's nine bug fixes and one version update (because of a bug fix) and
  one set of PCI ID additions. There's one bug fix in the core which is
  really a one liner (except that an additional sdev pointer was added
  for convenience) and the rest are in drivers"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target: core: Add TMF to tmr_list handling
  scsi: core: Kick the requeue list after inserting when flushing
  scsi: fnic: unlock on error path in fnic_queuecommand()
  scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
  scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
  scsi: smartpqi: Bump driver version to 2.1.26-030
  scsi: smartpqi: Fix logical volume rescan race condition
  scsi: smartpqi: Add new controller PCI IDs
  scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
  scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
  scsi: ufs: core: Simplify power management during async scan

Merge tag 'sh-for-v6.8-tag1' of git://git./linux/kernel/git/glaubitz/sh-linux

Pull sh updates from John Paul Adrian Glaubitz:
 "Since the large patch series to convert arch/sh to device tree support
  has not been finalized yet due to various maintainers still asking for
  changes to the series, this ended up being rather small consisting of
  just two fixes.

  The first patch by Geert Uytterhoeven addresses a build failure in the
  EcoVec platform code. And the second patch by Masahiro Yamada removes
  an unnecessary $(foreach ...) found in a Makefile of the vsyscall
  code.

   - Rename missed backlight field from fbdev to dev

   - Remove unnecessary $(foreach ...)"

* tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
  sh: vsyscall: Remove unnecessary $(foreach ...)
  sh: ecovec24: Rename missed backlight field from fbdev to dev