net: usb: qmi_wwan: Add support for Dell DW5829e

[ Upstream commit 8ecbb179286cbc91810c16caeb3396e06305cd0c ]

Dell DW5829e same as DW5821e except the CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
Also, DW5829e includes normal and eSIM type.
Please see below test evidence:

T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  5 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=413c ProdID=81e6 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  7 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=413c ProdID=81e4 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220209024717.8564-1-slark_xiao@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Fix tp_printk option related with tp_printk_stop_on_boot

[ Upstream commit 3203ce39ac0b2a57a84382ec184c7d4a0bede175 ]

The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.

This is similar to other kernel parameter issues, such as:
  Commit 745a600cf1a6 ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)

Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.

Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.com
Signed-off-by: JaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ]
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/rockchip: dw_hdmi: Do not leave clock enabled in error case

[ Upstream commit c0cfbb122275da1b726481de5a8cffeb24e6322b ]

The driver returns an error when devm_phy_optional_get() fails leaving
the previously enabled clock turned on. Change order and enable the
clock only after the phy has been acquired.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220126145549.617165-3-s.hauer@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>

xprtrdma: fix pointer derefs in error cases of rpcrdma_ep_create

[ Upstream commit a9c10b5b3b67b3750a10c8b089b2e05f5e176e33 ]

If there are failures then we must not leave the non-NULL pointers with
the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries
free them, resulting in an Oops.

Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Acked-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: aspeed: lpc-ctrl: Block error printing on probe defer cases

[ Upstream commit 301a5d3ad2432d7829f59432ca0a93a6defbb9a1 ]

Add a checking code when it gets -EPROBE_DEFER while getting a clock
resource. In this case, it doesn't need to print out an error message
because the probing will be re-visited.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20211104173709.222912-1-jae.hyun.yoo@intel.com
Link: https://lore.kernel.org/r/20220201070118.196372-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ata: libata-core: Disable TRIM on M88V29

[ Upstream commit c8ea23d5fa59f28302d4e3370c75d9c308e64410 ]

This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.

While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.

TRIM must be disabled for this device.

Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

lib/iov_iter: initialize "flags" in new pipe_buffer

commit 9d2231c5d74e13b2a0546fee6737ee4446017903 upstream.

The functions copy_page_to_iter_pipe() and push_pipe() can both
allocate a new pipe_buffer, but the "flags" member initializer is
missing.

Fixes: 241699cd72a8 ("new iov_iter flavour: pipe-backed")
To: Alexander Viro <viro@zeniv.linux.org.uk>
To: linux-fsdevel@vger.kernel.org
To: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kconfig: let 'shell' return enough output for deep path names

[ Upstream commit 8a4c5b2a6d8ea079fa36034e8167de87ab6f8880 ]

The 'shell' built-in only returns the first 256 bytes of the command's
output. In some cases, 'shell' is used to return a path; by bumping up
the buffer size to 4096 this lets us capture up to PATH_MAX.

The specific case where I ran into this was due to commit 1e860048c53e
("gcc-plugins: simplify GCC plugin-dev capability test"). After this
change, we now use `$(shell,$(CC) -print-file-name=plugin)` to return
a path; if the gcc path is particularly long, then the path ends up
truncated at the 256 byte mark, which makes the HAVE_GCC_PLUGINS
depends test always fail.

Signed-off-by: Brenda Streiff <brenda.streiff@ni.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: fixup build warnings in pidfd / clone3 tests

[ Upstream commit e2aa5e650b07693477dff554053605976789fd68 ]

These are some trivial fixups, which were needed to build the tests with
clang and -Werror. The following issues are fixed:

- Remove various unused variables.
- In child_poll_leader_exit_test, clang isn't smart enough to realize
  syscall(SYS_exit, 0) won't return, so it complains we never return
  from a non-void function. Add an extra exit(0) to appease it.
- In test_pidfd_poll_leader_exit, ret may be branched on despite being
  uninitialized, if we have !use_waitpid. Initialize it to zero to get
  the right behavior in that case.

Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pidfd: fix test failure due to stack overflow on some arches

[ Upstream commit 4cbd93c3c110447adc66cb67c08af21f939ae2d7 ]

When running the pidfd_fdinfo_test on arm64, it fails for me. After some
digging, the reason is that the child exits due to SIGBUS, because it
overflows the 1024 byte stack we've reserved for it.

To fix the issue, increase the stack size to 8192 bytes (this number is
somewhat arbitrary, and was arrived at through experimentation -- I kept
doubling until the failure no longer occurred).

Also, let's make the issue easier to debug. wait_for_pid() returns an
ambiguous value: it may return -1 in all of these cases:

1. waitpid() itself returned -1
2. waitpid() returned success, but we found !WIFEXITED(status).
3. The child process exited, but it did so with a -1 exit code.

There's no way for the caller to tell the difference. So, at least log
which occurred, so the test runner can debug things.

While debugging this, I found that we had !WIFEXITED(), because the
child exited due to a signal. This seems like a reasonably common case,
so also print out whether or not we have WIFSIGNALED(), and the
associated WTERMSIG() (if any). This lets us see the SIGBUS I'm fixing
clearly when it occurs.

Finally, I'm suspicious of allocating the child's stack on our stack.
man clone(2) suggests that the correct way to do this is with mmap(),
and in particular by setting MAP_STACK. So, switch to doing it that way
instead.

Signed-off-by: Axel Rasmussen <axelrasmussen@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: meson-g12: drop BL32 region from SEI510/SEI610

[ Upstream commit f26573e2bc9dfd551a0d5c6971f18cc546543312 ]

The BL32/TEE reserved-memory region is now inherited from the common
family dtsi (meson-g12-common) so we can drop it from board files.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220126044954.19069-4-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: meson-g12: add ATF BL32 reserved-memory region

[ Upstream commit 08982a1b3aa2611c9c711d24825c9002d28536f4 ]

Add an additional reserved memory region for the BL32 trusted firmware
present in many devices that boot from Amlogic vendor u-boot.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220126044954.19069-3-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: meson-gx: add ATF BL32 reserved-memory region

[ Upstream commit 76577c9137456febb05b0e17d244113196a98968 ]

Add an additional reserved memory region for the BL32 trusted firmware
present in many devices that boot from Amlogic vendor u-boot.

Suggested-by: Mateusz Krzak <kszaquitto@gmail.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220126044954.19069-2-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: conntrack: don't refresh sctp entries in closed state

[ Upstream commit 77b337196a9d87f3d6bb9b07c0436ecafbffda1e ]

Vivek Thrivikraman reported:
 An SCTP server application which is accessed continuously by client
 application.
 When the session disconnects the client retries to establish a connection.
 After restart of SCTP server application the session is not established
 because of stale conntrack entry with connection state CLOSED as below.

 (removing this entry manually established new connection):

 sctp 9 CLOSED src=10.141.189.233 [..]  [ASSURED]

Just skip timeout update of closed entries, we don't want them to
stay around forever.

Reported-and-tested-by: Vivek Thrivikraman <vivek.thrivikraman@est.tech>
Closes: https://bugzilla.netfilter.org/show_bug.cgi?id=1579
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

irqchip/sifive-plic: Add missing thead,c900-plic match string

[ Upstream commit 1d4df649cbb4b26d19bea38ecff4b65b10a1bbca ]

The thead,c900-plic has been used in opensbi to distinguish
PLIC [1]. Although PLICs have the same behaviors in Linux,
they are different hardware with some custom initializing in
firmware(opensbi).

Qute opensbi patch commit-msg by Samuel:

  The T-HEAD PLIC implementation requires setting a delegation bit
  to allow access from S-mode. Now that the T-HEAD PLIC has its own
  compatible string, set this bit automatically from the PLIC driver,
  instead of reaching into the PLIC's MMIO space from another driver.

[1]: https://github.com/riscv-software-src/opensbi/commit/78c2b19218bd62653b9fb31623a42ced45f38ea6

Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Anup Patel <anup@brainfault.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220130135634.1213301-3-guoren@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: usb: Leave some clocks running during suspend

[ Upstream commit 42fed57046fc74586d7058bd51a1c10ac9c690cb ]

The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).

The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.

Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: OMAP2+: adjust the location of put_device() call in omapdss_init_of

[ Upstream commit 34596ba380b03d181e24efd50e2f21045bde3696 ]

This was found by coccicheck:
./arch/arm/mach-omap2/display.c, 272, 1-7, ERROR missing put_device;
call of_find_device_by_node on line 258, but without a corresponding
object release within this function.

Move the put_device() call before the if judgment.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: OMAP2+: hwmod: Add of_node_put() before break

[ Upstream commit 80c469a0a03763f814715f3d12b6f3964c7423e8 ]

Fix following coccicheck warning:
./arch/arm/mach-omap2/omap_hwmod.c:753:1-23: WARNING: Function
for_each_matching_node should have of_node_put() before break

Early exits from for_each_matching_node should decrement the
node reference counter.

Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFS: Don't set NFS_INO_INVALID_XATTR if there is no xattr cache

[ Upstream commit 848fdd62399c638e65a1512616acaa5de7d5c5e8 ]

Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW

[ Upstream commit 710c476514313c74045c41c0571bb5178fd16e3d ]

AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't mask off the high nybble when configuring a
RAW perf event.

Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-2-jmattson@google.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/pmu: Don't truncate the PerfEvtSeln MSR when creating a perf event

[ Upstream commit b8bfee85f1307426e0242d654f3a14c06ef639c5 ]

AMD's event select is 3 nybbles, with the high nybble in bits 35:32 of
a PerfEvtSeln MSR. Don't drop the high nybble when setting up the
config field of a perf_event_attr structure for a call to
perf_event_create_kernel_counter().

Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Reported-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220203014813.2130559-1-jmattson@google.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/pmu: Refactoring find_arch_event() to pmc_perf_hw_id()

[ Upstream commit 7c174f305cbee6bdba5018aae02b84369e7ab995 ]

The find_arch_event() returns a "unsigned int" value,
which is used by the pmc_reprogram_counter() to
program a PERF_TYPE_HARDWARE type perf_event.

The returned value is actually the kernel defined generic
perf_hw_id, let's rename it to pmc_perf_hw_id() with simpler
incoming parameters for better self-explanation.

Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211130074221.93635-3-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Drivers: hv: vmbus: Fix memory leak in vmbus_add_channel_kobj

[ Upstream commit 8bc69f86328e87a0ffa79438430cc82f3aa6a194 ]

kobject_init_and_add() takes reference even when it fails.
According to the doc of kobject_init_and_add()：

   If this function returns an error, kobject_put() must be called to
   properly clean up the memory associated with the object.

Fix memory leak by calling kobject_put().

Fixes: c2e5df616e1a ("vmbus: add per-channel sysfs info")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Juan Vazquez <juvazq@linux.microsoft.com>
Link: https://lore.kernel.org/r/20220203173008.43480-1-linmq006@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mtd: rawnand: brcmnand: Fixed incorrect sub-page ECC status

commit 36415a7964711822e63695ea67fede63979054d9 upstream.

The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)

The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.

The fix is to stop checking for bad bits only if we already have a bad
bits status.

Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: qcom: Fix clock sequencing in qcom_nandc_probe()

commit 5c23b3f965bc9ee696bf2ed4bdc54d339dd9a455 upstream.

Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.

This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.

If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is

qcom_nandc_unalloc(nandc);

clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);

dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
   DMA_BIDIRECTIONAL, 0);

Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.

Fixes: c76b78d8ec05 ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_tty: do not look ahead for EOL character past the end of the buffer

commit 3593030761630e09200072a4bd06468892c27be3 upstream.

Daniel Gibson reports that the n_tty code gets line termination wrong in
very specific cases:

 "If you feed a line with exactly 64 chars + terminating newline, and
  directly afterwards (without reading) another line into a pseudo
  terminal, the the first read() on the other side will return the 64
  char line *without* terminating newline, and the next read() will
  return the missing terminating newline AND the complete next line (if
  it fits in the buffer)"

and bisected the behavior to commit 3b830a9c34d5 ("tty: convert
tty_ldisc_ops 'read()' function to take a kernel pointer").

Now, digging deeper, it turns out that the behavior isn't exactly new:
what changed in commit 3b830a9c34d5 was that the tty line discipline
.read() function is now passed an intermediate kernel buffer rather than
the final user space buffer.

And that intermediate kernel buffer is 64 bytes in size - thus that
special case with exactly 64 bytes plus terminating newline.

The same problem did exist before, but historically the boundary was not
the 64-byte chunk, but the user-supplied buffer size, which is obviously
generally bigger (and potentially bigger than N_TTY_BUF_SIZE, which
would hide the issue entirely).

The reason is that the n_tty canon_copy_from_read_buf() code would look
ahead for the EOL character one byte further than it would actually
copy.  It would then decide that it had found the terminator, and unmark
it as an EOL character - which in turn explains why the next read
wouldn't then be terminated by it.

Now, the reason it did all this in the first place is related to some
historical and pretty obscure EOF behavior, see commit ac8f3bf8832a
("n_tty: Fix poll() after buffer-limited eof push read") and commit
40d5e0905a03 ("n_tty: Fix EOF push handling").

And the reason for the EOL confusion is that we treat EOF as a special
EOL condition, with the EOL character being NUL (aka "__DISABLED_CHAR"
in the kernel sources).

So that EOF look-ahead also affects the normal EOL handling.

This patch just removes the look-ahead that causes problems, because EOL
is much more critical than the historical "EOF in the middle of a line
that coincides with the end of the buffer" handling ever was.

Now, it is possible that we should indeed re-introduce the "look at next
character to see if it's a EOF" behavior, but if so, that should be done
not at the kernel buffer chunk boundary in canon_copy_from_read_buf(),
but at a higher level, when we run out of the user buffer.

In particular, the place to do that would be at the top of
'n_tty_read()', where we check if it's a continuation of a previously
started read, and there is no more buffer space left, we could decide to
just eat the __DISABLED_CHAR at that point.

But that would be a separate patch, because I suspect nobody actually
cares, and I'd like to get a report about it before bothering.

Fixes: 3b830a9c34d5 ("tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer")
Fixes: ac8f3bf8832a ("n_tty: Fix  poll() after buffer-limited eof push read")
Fixes: 40d5e0905a03 ("n_tty: Fix EOF push handling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Reported-and-tested-by: Daniel Gibson <metalcaedes@gmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NFS: Do not report writeback errors in nfs_getattr()

commit d19e0183a88306acda07f4a01fedeeffe2a2a06b upstream.

The result of the writeback, whether it is an ENOSPC or an EIO, or
anything else, does not inhibit the NFS client from reporting the
correct file timestamps.

Fixes: 79566ef018f5 ("NFS: Getattr doesn't require data sync semantics")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NFS: LOOKUP_DIRECTORY is also ok with symlinks

commit e0caaf75d443e02e55e146fd75fe2efc8aed5540 upstream.

Commit ac795161c936 (NFSv4: Handle case where the lookup of a directory
fails) [1], part of Linux since 5.17-rc2, introduced a regression, where
a symbolic link on an NFS mount to a directory on another NFS does not
resolve(?) the first time it is accessed:

Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: ac795161c936 ("NFSv4: Handle case where the lookup of a directory fails")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Donald Buczek <buczek@molgen.mpg.de>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block/wbt: fix negative inflight counter when remove scsi device

commit e92bc4cd34de2ce454bdea8cd198b8067ee4e123 upstream.

Now that we disable wbt by set WBT_STATE_OFF_DEFAULT in
wbt_disable_default() when switch elevator to bfq. And when
we remove scsi device, wbt will be enabled by wbt_enable_default.
If it become false positive between wbt_wait() and wbt_track()
when submit write request.

The following is the scenario that triggered the problem.

T1                          T2                           T3
                            elevator_switch_mq
                            bfq_init_queue
                            wbt_disable_default <= Set
                            rwb->enable_state (OFF)
Submit_bio
blk_mq_make_request
rq_qos_throttle
<= rwb->enable_state (OFF)
                                                         scsi_remove_device
                                                         sd_remove
                                                         del_gendisk
                                                         blk_unregister_queue
                                                         elv_unregister_queue
                                                         wbt_enable_default
                                                         <= Set rwb->enable_state (ON)
q_qos_track
<= rwb->enable_state (ON)
^^^^^^ this request will mark WBT_TRACKED without inflight add and will
lead to drop rqw->inflight to -1 in wbt_done() which will trigger IO hung.

Fix this by move wbt_enable_default() from elv_unregister to
bfq_exit_queue(). Only re-enable wbt when bfq exit.

Fixes: 76a8040817b4b ("blk-wbt: make sure throttle is enabled properly")

Remove oneline stale comment, and kill one oneshot local variable.

Signed-off-by: Ming Lei <ming.lei@rehdat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/linux-block/20211214133103.551813-1-qiulaibin@huawei.com/
Signed-off-by: Laibin Qiu <qiulaibin@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tas2770: Insert post reset delay

commit 307f31452078792aab94a729fce33200c6e42dc4 upstream.

Per TAS2770 datasheet there must be a 1 ms delay from reset to first
command. So insert delays into the driver where appropriate.

Fixes: 1a476abc723e ("tas2770: add tas2770 smart PA kernel driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220204095301.5554-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: SVM: Never reject emulation due to SMAP errata for !SEV guests

commit 55467fcd55b89c622e62b4afe60ac0eb2fae91f2 upstream.

Always signal that emulation is possible for !SEV guests regardless of
whether or not the CPU provided a valid instruction byte stream.  KVM can
read all guest state (memory and registers) for !SEV guests, i.e. can
fetch the code stream from memory even if the CPU failed to do so because
of the SMAP errata.

Fixes: 05d5a4863525 ("KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)")
Cc: stable@vger.kernel.org
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[jwang: adjust context for kernel 5.10.101]
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mtd: rawnand: gpmi: don't leak PM reference in error path

commit 9161f365c91614e5a3f5c6dcc44c3b1b33bc59c0 upstream.

If gpmi_nfc_apply_timings() fails, the PM runtime usage counter must be
dropped.

Reported-by: Pavel Machek <pavel@denx.de>
Fixes: f53d4c109a66 ("mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timings")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220125081619.6286-1-ceggers@arri.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/lib/sstep: fix 'ptesync' build error

commit fe663df7825811358531dc2e8a52d9eaa5e3515e upstream.

Building tinyconfig with gcc (Debian 11.2.0-16) and assembler (Debian
2.37.90.20220207) the following build error shows up:

  {standard input}: Assembler messages:
  {standard input}:2088: Error: unrecognized opcode: `ptesync'
  make[3]: *** [/builds/linux/scripts/Makefile.build:287: arch/powerpc/lib/sstep.o] Error 1

Add the 'ifdef CONFIG_PPC64' around the 'ptesync' in function
'emulate_update_regs()' to like it is in 'analyse_instr()'. Since it looks like
it got dropped inadvertently by commit 3cdfcbfd32b9 ("powerpc: Change
analyse_instr so it doesn't modify *regs").

A key detail is that analyse_instr() will never recognise lwsync or
ptesync on 32-bit (because of the existing ifdef), and as a result
emulate_update_regs() should never be called with an op specifying
either of those on 32-bit. So removing them from emulate_update_regs()
should be a nop in terms of runtime behaviour.

Fixes: 3cdfcbfd32b9 ("powerpc: Change analyse_instr so it doesn't modify *regs")
Cc: stable@vger.kernel.org # v4.14+
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
[mpe: Add last paragraph of change log mentioning analyse_instr() details]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220211005113.1361436-1-anders.roxell@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw_range()

commit 650204ded3703b5817bd4b6a77fa47d333c4f902 upstream.

When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220201155629.120510-4-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: ops: Fix stereo change notifications in snd_soc_put_volsw()

commit 564778d7b1ea465f9487eedeece7527a033549c5 upstream.

When writing out a stereo control we discard the change notification from
the first channel, meaning that events are only generated based on changes
to the second channel. Ensure that we report a change if either channel
has changed.

Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220201155629.120510-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Fix missing codec probe on Shenker Dock 15

commit dd8e5b161d7fb9cefa1f1d6e35a39b9e1563c8d3 upstream.

By some unknown reason, BIOS on Shenker Dock 15 doesn't set up the
codec mask properly for the onboard audio.  Let's set the forced codec
mask to enable the codec discovery.

Reported-by: dmummenschanz@web.de
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/trinity-f018660b-95c9-442b-a2a8-c92a56eb07ed-1644345967148@3c-app-webde-bap22
Link: https://lore.kernel.org/r/20220214100020.8870-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda: Fix regression on forced probe mask option

commit 6317f7449348a897483a2b4841f7a9190745c81b upstream.

The forced probe mask via probe_mask 0x100 bit doesn't work any longer
as expected since the bus init code was moved and it's clearing the
codec_mask value that was set beforehand.  This patch fixes the
long-time regression by moving the check_probe_mask() call.

Fixes: a41d122449be ("ALSA: hda - Embed bus into controller object")
Reported-by: dmummenschanz@web.de
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/trinity-f018660b-95c9-442b-a2a8-c92a56eb07ed-1644345967148@3c-app-webde-bap22
Link: https://lore.kernel.org/r/20220214100020.8870-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Fix deadlock by COEF mutex

commit 2a845837e3d0ddaed493b4c5c4643d7f0542804d upstream.

The recently introduced coef_mutex for Realtek codec seems causing a
deadlock when the relevant code is invoked from the power-off state;
then the HD-audio core tries to power-up internally, and this kicks
off the codec runtime PM code that tries to take the same coef_mutex.

In order to avoid the deadlock, do the temporary power up/down around
the coef_mutex acquisition and release.  This assures that the
power-up sequence runs before the mutex, hence no re-entrance will
happen.

Fixes: b837a9f5ab3b ("ALSA: hda: realtek: Fix race at concurrent COEF updates")
Reported-and-tested-by: Julian Wollrath <jwollrath@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220214132838.4db10fca@schienar
Link: https://lore.kernel.org/r/20220214130410.21230-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Add quirk for Legion Y9000X 2019

commit c07f2c7b45413a9e50ba78630fda04ecfa17b4f2 upstream.

Legion Y9000X 2019 has the same speaker with Y9000X 2020,
but with a different quirk address. Add one quirk entry
to make the speaker work on Y9000X 2019 too.

Signed-off-by: Yu Huang <diwang90@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220212160835.165065-1-diwang90@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/exec: Add non-regular to TEST_GEN_PROGS

commit a7e793a867ae312cecdeb6f06cceff98263e75dd upstream.

non-regular file needs to be compiled and then copied to the output
directory. Remove it from TEST_PROGS and add it to TEST_GEN_PROGS. This
removes error thrown by rsync when non-regular object isn't found:

rsync: [sender] link_stat "/linux/tools/testing/selftests/exec/non-regular" failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1333) [sender=3.2.3]

Fixes: 0f71241a8e32 ("selftests/exec: add file type errno tests")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf bpf: Defer freeing string after possible strlen() on it

commit 31ded1535e3182778a1d0e5c32711f55da3bc512 upstream.

This was detected by the gcc in Fedora Rawhide's gcc:

  50    11.01 fedora:rawhide                : FAIL gcc version 12.0.1 20220205 (Red Hat 12.0.1-0) (GCC)
        inlined from 'bpf__config_obj' at util/bpf-loader.c:1242:9:
    util/bpf-loader.c:1225:34: error: pointer 'map_opt' may be used after 'free' [-Werror=use-after-free]
     1225 |                 *key_scan_pos += strlen(map_opt);
          |                                  ^~~~~~~~~~~~~~~
    util/bpf-loader.c:1223:9: note: call to 'free' here
     1223 |         free(map_name);
          |         ^~~~~~~~~~~~~~
    cc1: all warnings being treated as errors

So do the calculations on the pointer before freeing it.

Fixes: 04f9bf2bac72480c ("perf bpf-loader: Add missing '*' for key_scan_pos")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/lkml/Yg1VtQxKrPpS3uNA@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dpaa2-eth: Initialize mutex used in one step timestamping path

commit 07dd44852be89386ab12210df90a2d78779f3bff upstream.

1588 Single Step Timestamping code path uses a mutex to
enforce atomicity for two events:
- update of ptp single step register
- transmit ptp event packet

Before this patch the mutex was not initialized. This
caused unexpected crashes in the Tx function.

Fixes: c55211892f463 ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libsubcmd: Fix use-after-free for realloc(..., 0)

commit 52a9dab6d892763b2a8334a568bd4e2c1a6fde66 upstream.

GCC 12 correctly reports a potential use-after-free condition in the
xrealloc helper. Fix the warning by avoiding an implicit "free(ptr)"
when size == 0:

In file included from help.c:12:
In function 'xrealloc',
    inlined from 'add_cmdname' at help.c:24:2: subcmd-util.h:56:23: error: pointer may be used after 'realloc' [-Werror=use-after-free]
   56 |                 ret = realloc(ptr, size);
      |                       ^~~~~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
   52 |         void *ret = realloc(ptr, size);
      |                     ^~~~~~~~~~~~~~~~~~
subcmd-util.h:58:31: error: pointer may be used after 'realloc' [-Werror=use-after-free]
   58 |                         ret = realloc(ptr, 1);
      |                               ^~~~~~~~~~~~~~~
subcmd-util.h:52:21: note: call to 'realloc' here
   52 |         void *ret = realloc(ptr, size);
      |                     ^~~~~~~~~~~~~~~~~~

Fixes: 2f4ce5ec1d447beb ("perf tools: Finalize subcmd independence")
Reported-by: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kees Kook <keescook@chromium.org>
Tested-by: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Tested-by: Justin M. Forbes <jforbes@fedoraproject.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: linux-hardening@vger.kernel.org
Cc: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Link: http://lore.kernel.org/lkml/20220213182443.4037039-1-keescook@chromium.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: fix data-races around agg_select_timer

commit 9ceaf6f76b203682bb6100e14b3d7da4c0bedde8 upstream.

syzbot reported that two threads might write over agg_select_timer
at the same time. Make agg_select_timer atomic to fix the races.

BUG: KCSAN: data-race in bond_3ad_initiate_agg_selection / bond_3ad_state_machine_handler

read to 0xffff8881242aea90 of 4 bytes by task 1846 on cpu 1:
 bond_3ad_state_machine_handler+0x99/0x2810 drivers/net/bonding/bond_3ad.c:2317
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

write to 0xffff8881242aea90 of 4 bytes by task 25910 on cpu 0:
 bond_3ad_initiate_agg_selection+0x18/0x30 drivers/net/bonding/bond_3ad.c:1998
 bond_open+0x658/0x6f0 drivers/net/bonding/bond_main.c:3967
 __dev_open+0x274/0x3a0 net/core/dev.c:1407
 dev_open+0x54/0x190 net/core/dev.c:1443
 bond_enslave+0xcef/0x3000 drivers/net/bonding/bond_main.c:1937
 do_set_master net/core/rtnetlink.c:2532 [inline]
 do_setlink+0x94f/0x2500 net/core/rtnetlink.c:2736
 __rtnl_newlink net/core/rtnetlink.c:3414 [inline]
 rtnl_newlink+0xfeb/0x13e0 net/core/rtnetlink.c:3529
 rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5594
 netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2494
 rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5612
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x602/0x6d0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x728/0x850 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmsg+0x195/0x230 net/socket.c:2496
 __do_sys_sendmsg net/socket.c:2505 [inline]
 __se_sys_sendmsg net/socket.c:2503 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2503
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00000050 -> 0x0000004f

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25910 Comm: syz-executor.1 Tainted: G        W         5.17.0-rc4-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net_sched: add __rcu annotation to netdev->qdisc

commit 5891cd5ec46c2c2eb6427cb54d214b149635dd0e upstream.

syzbot found a data-race [1] which lead me to add __rcu
annotations to netdev->qdisc, and proper accessors
to get LOCKDEP support.

[1]
BUG: KCSAN: data-race in dev_activate / qdisc_lookup_rcu

write to 0xffff888168ad6410 of 8 bytes by task 13559 on cpu 1:
 attach_default_qdiscs net/sched/sch_generic.c:1167 [inline]
 dev_activate+0x2ed/0x8f0 net/sched/sch_generic.c:1221
 __dev_open+0x2e9/0x3a0 net/core/dev.c:1416
 __dev_change_flags+0x167/0x3f0 net/core/dev.c:8139
 rtnl_configure_link+0xc2/0x150 net/core/rtnetlink.c:3150
 __rtnl_newlink net/core/rtnetlink.c:3489 [inline]
 rtnl_newlink+0xf4d/0x13e0 net/core/rtnetlink.c:3529
 rtnetlink_rcv_msg+0x745/0x7e0 net/core/rtnetlink.c:5594
 netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2494
 rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5612
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x602/0x6d0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x728/0x850 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmsg+0x195/0x230 net/socket.c:2496
 __do_sys_sendmsg net/socket.c:2505 [inline]
 __se_sys_sendmsg net/socket.c:2503 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2503
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff888168ad6410 of 8 bytes by task 13560 on cpu 0:
 qdisc_lookup_rcu+0x30/0x2e0 net/sched/sch_api.c:323
 __tcf_qdisc_find+0x74/0x3a0 net/sched/cls_api.c:1050
 tc_del_tfilter+0x1c7/0x1350 net/sched/cls_api.c:2211
 rtnetlink_rcv_msg+0x5ba/0x7e0 net/core/rtnetlink.c:5585
 netlink_rcv_skb+0x14e/0x250 net/netlink/af_netlink.c:2494
 rtnetlink_rcv+0x18/0x20 net/core/rtnetlink.c:5612
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x602/0x6d0 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0x728/0x850 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:705 [inline]
 sock_sendmsg net/socket.c:725 [inline]
 ____sys_sendmsg+0x39a/0x510 net/socket.c:2413
 ___sys_sendmsg net/socket.c:2467 [inline]
 __sys_sendmsg+0x195/0x230 net/socket.c:2496
 __do_sys_sendmsg net/socket.c:2505 [inline]
 __se_sys_sendmsg net/socket.c:2503 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2503
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0xffffffff85dee080 -> 0xffff88815d96ec00

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 13560 Comm: syz-executor.2 Not tainted 5.17.0-rc3-syzkaller-00116-gf1baf68e1383-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 470502de5bdb ("net: sched: unlock rules update API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drop_monitor: fix data-race in dropmon_net_event / trace_napi_poll_hit

commit dcd54265c8bc14bd023815e36e2d5f9d66ee1fee upstream.

trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()

Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.

BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit

write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
 dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
 notifier_call_chain kernel/notifier.c:84 [inline]
 raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
 call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
 call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
 call_netdevice_notifiers net/core/dev.c:1945 [inline]
 unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
 ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
 vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
 ops_exit_list net/core/net_namespace.c:173 [inline]
 cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
 trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
 trace_napi_poll include/trace/events/napi.h:14 [inline]
 __napi_poll+0x36b/0x3f0 net/core/dev.c:6366
 napi_poll net/core/dev.c:6432 [inline]
 net_rx_action+0x29e/0x650 net/core/dev.c:6519
 __do_softirq+0x158/0x2de kernel/softirq.c:558
 do_softirq+0xb1/0xf0 kernel/softirq.c:459
 __local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
 _raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
 spin_unlock_bh include/linux/spinlock.h:394 [inline]
 ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
 wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

value changed: 0xffff88815883e000 -> 0x0000000000000000

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker

Fixes: 4ea7e38696c7 ("dropmon: add ability to detect when hardware dropsrxpackets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: force carrier update when releasing slave

commit a6ab75cec1e461f8a35559054c146c21428430b8 upstream.

In __bond_release_one(), bond_set_carrier() is only called when bond
device has no slave. Therefore, if we remove the up slave from a master
with two slaves and keep the down slave, the master will remain up.

Fix this by moving bond_set_carrier() out of if (!bond_has_slaves(bond))
statement.

Reproducer:
$ insmod bonding.ko mode=0 miimon=100 max_bonds=2
$ ifconfig bond0 up
$ ifenslave bond0 eth0 eth1
$ ifconfig eth0 down
$ ifenslave -d bond0 eth1
$ cat /proc/net/bonding/bond0

Fixes: ff59c4563a8d ("[PATCH] bonding: support carrier state for master")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/1645021088-38370-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ping: fix the dif and sdif check in ping_lookup

commit 35a79e64de29e8d57a5989aac57611c0cd29e13e upstream.

When 'ping' changes to use PING socket instead of RAW socket by:

   # sysctl -w net.ipv4.ping_group_range="0 100"

There is another regression caused when matching sk_bound_dev_if
and dif, RAW socket is using inet_iif() while PING socket lookup
is using skb->dev->ifindex, the cmd below fails due to this:

  # ip link add dummy0 type dummy
  # ip link set dummy0 up
  # ip addr add 192.168.111.1/24 dev dummy0
  # ping -I dummy0 192.168.111.1 -c1

The issue was also reported on:

  https://github.com/iputils/iputils/issues/104

But fixed in iputils in a wrong way by not binding to device when
destination IP is on device, and it will cause some of kselftests
to fail, as Jianlin noticed.

This patch is to use inet(6)_iif and inet(6)_sdif to get dif and
sdif for PING socket, and keep consistent with RAW socket.

Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ieee802154: ca8210: Fix lifs/sifs periods

commit bdc120a2bcd834e571ce4115aaddf71ab34495de upstream.

These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with the symbol_duration in order to get these
values in microseconds.

Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220201180629.93410-2-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: lantiq_gswip: fix use after free in gswip_remove()

commit 8c6ae46150a453f8ae9a6cd49b45f354f478587d upstream.

of_node_put(priv->ds->slave_mii_bus->dev.of_node) should be
done before mdiobus_free(priv->ds->slave_mii_bus).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Fixes: 0d120dfb5d67 ("net: dsa: lantiq_gswip: don't use devres for mdiobus")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1644921768-26477-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: lan9303: fix reset on probe

commit 6bb9681a43f34f2cab4aad6e2a02da4ce54d13c5 upstream.

The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this.  Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted.  Other uses of the gpio already use the correct polarity.

Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6: per-netns exclusive flowlabel checks

commit 0b0dff5b3b98c5c7ce848151df9da0b3cdf0cc8b upstream.

Ipv6 flowlabels historically require a reservation before use.
Optionally in exclusive mode (e.g., user-private).

Commit 59c820b2317f ("ipv6: elide flowlabel check if no exclusive
leases exist") introduced a fastpath that avoids this check when no
exclusive leases exist in the system, and thus any flowlabel use
will be granted.

That allows skipping the control operation to reserve a flowlabel
entirely. Though with a warning if the fast path fails:

  This is an optimization. Robust applications still have to revert to
  requesting leases if the fast path fails due to an exclusive lease.

Still, this is subtle. Better isolate network namespaces from each
other. Flowlabels are per-netns. Also record per-netns whether
exclusive leases are in use. Then behavior does not change based on
activity in other netns.

Changes
  v2
    - wrap in IS_ENABLED(CONFIG_IPV6) to avoid breakage if disabled

Fixes: 59c820b2317f ("ipv6: elide flowlabel check if no exclusive leases exist")
Link: https://lore.kernel.org/netdev/MWHPR2201MB1072BCCCFCE779E4094837ACD0329@MWHPR2201MB1072.namprd22.prod.outlook.com/
Reported-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Congyu Liu <liu3101@purdue.edu>
Link: https://lore.kernel.org/r/20220215160037.1976072-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: nft_synproxy: unregister hooks on init error path

commit 2b4e5fb4d3776c391e40fb33673ba946dd96012d upstream.

Disable the IPv4 hooks if the IPv6 hooks fail to be registered.

Fixes: ad49d86e07a4 ("netfilter: nf_tables: Add synproxy support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: netfilter: fix exit value for nft_concat_range

commit 2e71ec1a725a794a16e3862791ed43fe5ba6a06b upstream.

When the nft_concat_range test failed, it exit 1 in the code
specifically.

But when part of, or all of the test passed, it will failed the
[ ${passed} -eq 0 ] check and thus exit with 1, which is the same
exit value with failure result. Fix it by exit 0 when passed is not 0.

Fixes: 611973c1e06f ("selftests: netfilter: Introduce tests for sets with range concatenation")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: pcie: gen2: fix locking when "HW not ready"

commit 4c29c1e27a1e178a219b3877d055e6dd643bdfda upstream.

If we run into this error path, we shouldn't unlock the mutex
since it's not locked since. Fix this in the gen2 code as well.

Fixes: eda50cde58de ("iwlwifi: pcie: add context information support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.b8b0dfce16ef.Ie20f0f7b23e5911350a2766524300d2915e7b677@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: pcie: fix locking when "HW not ready"

commit e9848aed147708a06193b40d78493b0ef6abccf2 upstream.

If we run into this error path, we shouldn't unlock the mutex
since it's not locked since. Fix this.

Fixes: a6bd005fe92d ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20220128142706.5d16821d1433.Id259699ddf9806459856d6aefbdbe54477aecffd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/gvt: Make DRM_I915_GVT depend on X86

commit d72d69abfdb6e0375981cfdda8eb45143f12c77d upstream.

GVT is not supported on non-x86 platforms, So add
dependency of X86 on config parameter DRM_I915_GVT.

Fixes: 0ad35fed618c ("drm/i915: gvt: Introduce the basic architecture of GVT-g")
Signed-off-by: Siva Mullati <siva.mullati@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220107095235.243448-1-siva.mullati@intel.com
Reviewed-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vsock: remove vsock from connected table when connect is interrupted by a signal

commit b9208492fcaecff8f43915529ae34b3bcb03877c upstream.

vsock_connect() expects that the socket could already be in the
TCP_ESTABLISHED state when the connecting task wakes up with a signal
pending. If this happens the socket will be in the connected table, and
it is not removed when the socket state is reset. In this situation it's
common for the process to retry connect(), and if the connection is
successful the socket will be added to the connected table a second
time, corrupting the list.

Prevent this by calling vsock_remove_connected() if a signal is received
while waiting for a connection. This is harmless if the socket is not in
the connected table, and if it is in the table then removing it will
prevent list corruption from a double add.

Note for backporting: this patch requires d5afa82c977e ("vsock: correct
removal of socket from the list"), which is in all current stable trees
except 4.9.y.

Fixes: d021c344051a ("VSOCK: Introduce VM Sockets")
Signed-off-by: Seth Forshee <sforshee@digitalocean.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20220217141312.2297547-1-sforshee@digitalocean.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/opregion: check port number bounds for SWSCI display power state

commit ea958422291de248b9e2eaaeea36004e84b64043 upstream.

The mapping from enum port to whatever port numbering scheme is used by
the SWSCI Display Power State Notification is odd, and the memory of it
has faded. In any case, the parameter only has space for ports numbered
[0..4], and UBSAN reports bit shift beyond it when the platform has port
F or more.

Since the SWSCI functionality is supposed to be obsolete for new
platforms (i.e. ones that might have port F or more), just bail out
early if the mapped and mangled port number is beyond what the Display
Power State Notification can support.

Fixes: 9c4b0a683193 ("drm/i915: add opregion function to notify bios of encoder enable/disable")
Cc: <stable@vger.kernel.org> # v3.13+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4800
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cc363f42d6b5a5932b6d218fefcc8bdfb15dbbe5.1644489329.git.jani.nikula@intel.com
(cherry picked from commit 24a644ebbfd3b13cda702f98907f9dd123e34bf9)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: Fix backlight control on iMac 12,1

commit 364438fd629f7611a84c8e6d7de91659300f1502 upstream.

The iMac 12,1 does not use the gmux driver for backlight, so the radeon
backlight device is needed to set the brightness.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1838
Signed-off-by: Nicholas Bishop <nicholasbishop@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: fix use-after-free

commit bea2662e7818e15d7607d17d57912ac984275d94 upstream.

If no firmware was present at all (or, presumably, all of the
firmware files failed to parse), we end up unbinding by calling
device_release_driver(), which calls remove(), which then in
iwlwifi calls iwl_drv_stop(), freeing the 'drv' struct. However
the new code I added will still erroneously access it after it
was freed.

Set 'failure=false' in this case to avoid the access, all data
was already freed anyway.

Cc: stable@vger.kernel.org
Reported-by: Stefan Agner <stefan@agner.ch>
Reported-by: Wolfgang Walter <linux@stwm.de>
Reported-by: Jason Self <jason@bluehome.net>
Reported-by: Dominik Behr <dominik@dominikbehr.com>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: ab07506b0454 ("iwlwifi: fix leaks/bad data after failed firmware load")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208114728.e6b514cf4c85.Iffb575ca2a623d7859b542c33b2a507d01554251@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: lto: Merge module sections if and only if CONFIG_LTO_CLANG is enabled

commit 6a3193cdd5e5b96ac65f04ee42555c216da332af upstream.

Merge module sections only when using Clang LTO. With ld.bfd, merging
sections does not appear to update the symbol tables for the module,
e.g. 'readelf -s' shows the value that a symbol would have had, if
sections were not merged. ld.lld does not show this problem.

The stale symbol table breaks gdb's function disassembler, and presumably
other things, e.g.

  gdb -batch -ex "file arch/x86/kvm/kvm.ko" -ex "disassemble kvm_init"

reads the wrong bytes and dumps garbage.

Fixes: dd2776222abb ("kbuild: lto: merge module sections")
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210322234438.502582-1-seanjc@google.com
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: lto: merge module sections

commit dd2776222abb9893e5b5c237a2c8c880d8854cee upstream.

LLD always splits sections with LTO, which increases module sizes. This
change adds linker script rules to merge the split sections in the final
module.

Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20201211184633.3213045-6-samitolvanen@google.com
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

random: wake up /dev/random writers after zap

[ Upstream commit 042e293e16e3aa9794ce60c29f5b7b0c8170f933 ]

When account() is called, and the amount of entropy dips below
random_write_wakeup_bits, we wake up the random writers, so that they
can write some more in. However, the RNDZAPENTCNT/RNDCLEARPOOL ioctl
sets the entropy count to zero -- a potential reduction just like
account() -- but does not unblock writers. This commit adds the missing
logic to that ioctl to unblock waiting writers.

Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gcc-plugins/stackleak: Use noinstr in favor of notrace

[ Upstream commit dcb85f85fa6f142aae1fe86f399d4503d49f2b60 ]

While the stackleak plugin was already using notrace, objtool is now a
bit more picky.  Update the notrace uses to noinstr.  Silences the
following objtool warnings when building with:

CONFIG_DEBUG_ENTRY=y
CONFIG_STACK_VALIDATION=y
CONFIG_VMLINUX_VALIDATION=y
CONFIG_GCC_PLUGIN_STACKLEAK=y

  vmlinux.o: warning: objtool: do_syscall_64()+0x9: call to stackleak_track_stack() leaves .noinstr.text section
  vmlinux.o: warning: objtool: do_int80_syscall_32()+0x9: call to stackleak_track_stack() leaves .noinstr.text section
  vmlinux.o: warning: objtool: exc_general_protection()+0x22: call to stackleak_track_stack() leaves .noinstr.text section
  vmlinux.o: warning: objtool: fixup_bad_iret()+0x20: call to stackleak_track_stack() leaves .noinstr.text section
  vmlinux.o: warning: objtool: do_machine_check()+0x27: call to stackleak_track_stack() leaves .noinstr.text section
  vmlinux.o: warning: objtool: .text+0x5346e: call to stackleak_erase() leaves .noinstr.text section
  vmlinux.o: warning: objtool: .entry.text+0x143: call to stackleak_erase() leaves .noinstr.text section
  vmlinux.o: warning: objtool: .entry.text+0x10eb: call to stackleak_erase() leaves .noinstr.text section
  vmlinux.o: warning: objtool: .entry.text+0x17f9: call to stackleak_erase() leaves .noinstr.text section

Note that the plugin's addition of calls to stackleak_track_stack() from
noinstr functions is expected to be safe, as it isn't runtime
instrumentation and is self-contained.

Cc: Alexander Popov <alex.popov@linux.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "module, async: async_synchronize_full() on module init iff async is used"

[ Upstream commit 67d6212afda218d564890d1674bab28e8612170f ]

This reverts commit 774a1221e862b343388347bac9b318767336b20b.

We need to finish all async code before the module init sequence is
done.  In the reverted commit the PF_USED_ASYNC flag was added to mark a
thread that called async_schedule().  Then the PF_USED_ASYNC flag was
used to determine whether or not async_synchronize_full() needs to be
invoked.  This works when modprobe thread is calling async_schedule(),
but it does not work if module dispatches init code to a worker thread
which then calls async_schedule().

For example, PCI driver probing is invoked from a worker thread based on
a node where device is attached:

if (cpu < nr_cpu_ids)
error = work_on_cpu(cpu, local_pci_probe, &ddi);
else
error = local_pci_probe(&ddi);

We end up in a situation where a worker thread gets the PF_USED_ASYNC
flag set instead of the modprobe thread.  As a result,
async_synchronize_full() is not invoked and modprobe completes without
waiting for the async code to finish.

The issue was discovered while loading the pm80xx driver:
(scsi_mod.scan=async)

modprobe pm80xx                      worker
...
  do_init_module()
  ...
    pci_call_probe()
      work_on_cpu(local_pci_probe)
                                     local_pci_probe()
                                       pm8001_pci_probe()
                                         scsi_scan_host()
                                           async_schedule()
                                           worker->flags |= PF_USED_ASYNC;
                                     ...
      < return from worker >
  ...
  if (current->flags & PF_USED_ASYNC) <--- false
   async_synchronize_full();

Commit 21c3c5d28007 ("block: don't request module during elevator init")
fixed the deadlock issue which the reverted commit 774a1221e862
("module, async: async_synchronize_full() on module init iff async is
used") tried to fix.

Since commit 0fdff3ec6d87 ("async, kmod: warn on synchronous
request_module() from async workers") synchronous module loading from
async is not allowed.

Given that the original deadlock issue is fixed and it is no longer
allowed to call synchronous request_module() from async we can remove
PF_USED_ASYNC flag to make module init consistently invoke
async_synchronize_full() unless async module probe is requested.

Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Reviewed-by: Changyuan Lyu <changyuanl@google.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/Xen: streamline (and fix) PV CPU enumeration

[ Upstream commit e25a8d959992f61b64a58fc62fb7951dc6f31d1f ]

This started out with me noticing that "dom0_max_vcpus=<N>" with <N>
larger than the number of physical CPUs reported through ACPI tables
would not bring up the "excess" vCPU-s. Addressing this is the primary
purpose of the change; CPU maps handling is being tidied only as far as
is necessary for the change here (with the effect of also avoiding the
setting up of too much per-CPU infrastructure, i.e. for CPUs which can
never come online).

Noticing that xen_fill_possible_map() is called way too early, whereas
xen_filter_cpu_maps() is called too late (after per-CPU areas were
already set up), and further observing that each of the functions serves
only one of Dom0 or DomU, it looked like it was better to simplify this.
Use the .get_smp_config hook instead, uniformly for Dom0 and DomU.
xen_fill_possible_map() can be dropped altogether, while
xen_filter_cpu_maps() is re-purposed but not otherwise changed.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/2dbd5f0a-9859-ca2d-085e-a02f7166c610@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: fix logic inversion in check

[ Upstream commit e8ae38720e1a685fd98cfa5ae118c9d07b45ca79 ]

We probably never trigger this, but the logic inside the check is
inverted.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-rdma: fix possible use-after-free in transport error_recovery work

[ Upstream commit b6bb1722f34bbdbabed27acdceaf585d300c5fd2 ]

While nvme_rdma_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.

Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-tcp: fix possible use-after-free in transport error_recovery work

[ Upstream commit ff9fc7ebf5c06de1ef72a69f9b1ab40af8b07f9e ]

While nvme_tcp_submit_async_event_work is checking the ctrl and queue
state before preparing the AER command and scheduling io_work, in order
to fully prevent a race where this check is not reliable the error
recovery work must flush async_event_work before continuing to destroy
the admin queue after setting the ctrl state to RESETTING such that
there is no race .submit_async_event and the error recovery handler
itself changing the ctrl state.

Tested-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: fix a possible use-after-free in controller reset during load

[ Upstream commit 0fa0f99fc84e41057cbdd2efbfe91c6b2f47dd9d ]

Unlike .queue_rq, in .submit_async_event drivers may not check the ctrl
readiness for AER submission. This may lead to a use-after-free
condition that was observed with nvme-tcp.

The race condition may happen in the following scenario:
1. driver executes its reset_ctrl_work
2. -> nvme_stop_ctrl - flushes ctrl async_event_work
3. ctrl sends AEN which is received by the host, which in turn
   schedules AEN handling
4. teardown admin queue (which releases the queue socket)
5. AEN processed, submits another AER, calling the driver to submit
6. driver attempts to send the cmd
==> use-after-free

In order to fix that, add ctrl state check to validate the ctrl
is actually able to accept the AER submission.

This addresses the above race in controller resets because the driver
during teardown should:
1. change ctrl state to RESETTING
2. flush async_event_work (as well as other async work elements)

So after 1,2, any other AER command will find the
ctrl state to be RESETTING and bail out without submitting the AER.

Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: pm8001: Fix use-after-free for aborted SSP/STP sas_task

[ Upstream commit df7abcaa1246e2537ab4016077b5443bb3c09378 ]

Currently a use-after-free may occur if a sas_task is aborted by the upper
layer before we handle the I/O completion in mpi_ssp_completion() or
mpi_sata_completion().

In this case, the following are the two steps in handling those I/O
completions:

 - Call complete() to inform the upper layer handler of completion of
   the I/O.

 - Release driver resources associated with the sas_task in
   pm8001_ccb_task_free() call.

When complete() is called, the upper layer may free the sas_task. As such,
we should not touch the associated sas_task afterwards, but we do so in the
pm8001_ccb_task_free() call.

Fix by swapping the complete() and pm8001_ccb_task_free() calls ordering.

Link: https://lore.kernel.org/r/1643289172-165636-4-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: pm8001: Fix use-after-free for aborted TMF sas_task

[ Upstream commit 61f162aa4381845acbdc7f2be4dfb694d027c018 ]

Currently a use-after-free may occur if a TMF sas_task is aborted before we
handle the IO completion in mpi_ssp_completion(). The abort occurs due to
timeout.

When the timeout occurs, the SAS_TASK_STATE_ABORTED flag is set and the
sas_task is freed in pm8001_exec_internal_tmf_task().

However, if the I/O completion occurs later, the I/O completion still
thinks that the sas_task is available. Fix this by clearing the ccb->task
if the TMF times out - the I/O completion handler does nothing if this
pointer is cleared.

Link: https://lore.kernel.org/r/1643289172-165636-3-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

quota: make dquot_quota_sync return errors from ->sync_fs

[ Upstream commit dd5532a4994bfda0386eb2286ec00758cee08444 ]

Strangely, dquot_quota_sync ignores the return code from the ->sync_fs
call, which means that quotacalls like Q_SYNC never see the error.  This
doesn't seem right, so fix that.

Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vfs: make freeze_super abort when sync_filesystem returns error

[ Upstream commit 2719c7160dcfaae1f73a1c0c210ad3281c19022e ]

If we fail to synchronize the filesystem while preparing to freeze the
fs, abort the freeze.

Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ax25: improve the incomplete fix to avoid UAF and NPD bugs

[ Upstream commit 4e0f718daf97d47cf7dec122da1be970f145c809 ]

The previous commit 1ade48d0c27d ("ax25: NPD bug when detaching
AX25 device") introduce lock_sock() into ax25_kill_by_device to
prevent NPD bug. But the concurrency NPD or UAF bug will occur,
when lock_sock() or release_sock() dereferences the ax25_cb->sock.

The NULL pointer dereference bug can be shown as below:

ax25_kill_by_device()        | ax25_release()
                             |   ax25_destroy_socket()
                             |     ax25_cb_del()
  ...                        |     ...
                             |     ax25->sk=NULL;
  lock_sock(s->sk); //(1)    |
  s->ax25_dev = NULL;        |     ...
  release_sock(s->sk); //(2) |
  ...                        |

The root cause is that the sock is set to null before dereference
site (1) or (2). Therefore, this patch extracts the ax25_cb->sock
in advance, and uses ax25_list_lock to protect it, which can synchronize
with ax25_cb_del() and ensure the value of sock is not null before
dereference sites.

The concurrency UAF bug can be shown as below:

ax25_kill_by_device()        | ax25_release()
                             |   ax25_destroy_socket()
  ...                        |   ...
                             |   sock_put(sk); //FREE
  lock_sock(s->sk); //(1)    |
  s->ax25_dev = NULL;        |   ...
  release_sock(s->sk); //(2) |
  ...                        |

The root cause is that the sock is released before dereference
site (1) or (2). Therefore, this patch uses sock_hold() to increase
the refcount of sock and uses ax25_list_lock to protect it, which
can synchronize with ax25_cb_del() in ax25_destroy_socket() and
ensure the sock wil not be released before dereference sites.

Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: skip mincore.check_file_mmap when fs lacks needed support

[ Upstream commit dae1d8ac31896988e7313384c0370176a75e9b45 ]

Report mincore.check_file_mmap as SKIP instead of FAIL if the underlying
filesystem lacks support of O_TMPFILE or fallocate since such failures
are not really related to mincore functionality.

Cc: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: openat2: Skip testcases that fail with EOPNOTSUPP

[ Upstream commit ac9e0a250bb155078601a5b999aab05f2a04d1ab ]

Skip testcases that fail since the requested valid flags combination is not
supported by the underlying filesystem.

Cc: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: openat2: Add missing dependency in Makefile

[ Upstream commit ea3396725aa143dd42fe388cb67e44c90d2fb719 ]

Add a dependency on header helpers.h to the main target; while at that add
to helpers.h also a missing include for bool types.

Cc: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: openat2: Print also errno in failure messages

[ Upstream commit e051cdf655fa016692008a446a060eff06222bb5 ]

In E_func() macro, on error, print also errno in order to aid debugging.

Cc: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/zram: Adapt the situation that /dev/zram0 is being used

[ Upstream commit 01dabed20573804750af5c7bf8d1598a6bf7bf6e ]

If zram-generator package is installed and works, then we can not remove
zram module because zram swap is being used. This case needs a clean zram
environment, change this test by using hot_add/hot_remove interface. So
even zram device is being used, we still can add zram device and remove
them in cleanup.

The two interface was introduced since kernel commit 6566d1a32bf7("zram:
add dynamic device add/remove functionality") in v4.2-rc1. If kernel
supports these two interface, we use hot_add/hot_remove to slove this
problem, if not, just check whether zram is being used or built in, then
skip it on old kernel.

Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/zram01.sh: Fix compression ratio calculation

[ Upstream commit d18da7ec3719559d6e74937266d0416e6c7e0b31 ]

zram01 uses `free -m` to measure zram memory usage. The results are no
sense because they are polluted by all running processes on the system.

We Should only calculate the free memory delta for the current process.
So use the third field of /sys/block/zram<id>/mm_stat to measure memory
usage instead. The file is available since kernel 4.1.

orig_data_size(first): uncompressed size of data stored in this disk.
compr_data_size(second): compressed size of data stored in this disk
mem_used_total(third): the amount of memory allocated for this disk

Also remove useless zram cleanup call in zram_fill_fs and so we don't
need to cleanup zram twice if fails.

Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/zram: Skip max_comp_streams interface on newer kernel

[ Upstream commit fc4eb486a59d70bd35cf1209f0e68c2d8b979193 ]

Since commit 43209ea2d17a ("zram: remove max_comp_streams internals"), zram
has switched to per-cpu streams. Even kernel still keep this interface for
some reasons, but writing to max_comp_stream doesn't take any effect. So
skip it on newer kernel ie 4.7.

The code that comparing kernel version is from xfstests testsuite ext4/053.

Signed-off-by: Yang Xu <xuyang2018.jy@fujitsu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ieee802154: at86rf230: Stop leaking skb's

[ Upstream commit e5ce576d45bf72fd0e3dc37eff897bfcc488f6a9 ]

Upon error the ieee802154_xmit_complete() helper is not called. Only
ieee802154_wake_queue() is called manually. In the Tx case we then leak
the skb structure.

Free the skb structure upon error before returning when appropriate.

As the 'is_tx = 0' cannot be moved in the complete handler because of a
possible race between the delay in switching to STATE_RX_AACK_ON and a
new interrupt, we introduce an intermediate 'was_tx' boolean just for
this purpose.

There is no Fixes tag applying here, many changes have been made on this
area and the issue kind of always existed.

Suggested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20220125121426.848337-4-miquel.raynal@bootlin.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kselftest: signal all child processes

[ Upstream commit 92d25637a3a45904292c93f1863c6bbda4e3e38f ]

We have some many cases that will create child process as well, such as
pidfd_wait. Previously, we will signal/kill the parent process when it
is time out, but this signal will not be sent to its child process. In
such case, if child process doesn't terminate itself, ksefltest framework
will hang forever.

Here we group all its child processes so that kill() can signal all of
them in timeout.

Fixed change log: Shuah Khan <skhan@linuxfoundation.org>

Suggested-by: yang xu <xuyang2018.jy@cn.fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: rtc: Increase test timeout so that all tests run

[ Upstream commit f034cc1301e7d83d4ec428dd6b8ffb57ca446efb ]

The timeout setting for the rtc kselftest is currently 90 seconds. This
setting is used by the kselftest runner to stop running a test if it
takes longer than the assigned value.

However, two of the test cases inside rtc set alarms. These alarms are
set to the next beginning of the minute, so each of these test cases may
take up to, in the worst case, 60 seconds.

In order to allow for all test cases in rtc to run, even in the worst
case, when using the kselftest runner, the timeout value should be
increased to at least 120. Set it to 180, so there's some additional
slack.

Correct operation can be tested by running the following command right
after the start of a minute (low second count), and checking that all
test cases run:

./run_kselftest.sh -c rtc

Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: ISST: Fix possible circular locking dependency detected

[ Upstream commit 17da2d5f93692086dd096a975225ffd5622d0bf8 ]

As reported:

[  256.104522] ======================================================
[  256.113783] WARNING: possible circular locking dependency detected
[  256.120093] 5.16.0-rc6-yocto-standard+ #99 Not tainted
[  256.125362] ------------------------------------------------------
[  256.131673] intel-speed-sel/844 is trying to acquire lock:
[  256.137290] ffffffffc036f0d0 (punit_misc_dev_lock){+.+.}-{3:3}, at: isst_if_open+0x18/0x90 [isst_if_common]
[  256.147171]
[  256.147171] but task is already holding lock:
[  256.153135] ffffffff8ee7cb50 (misc_mtx){+.+.}-{3:3}, at: misc_open+0x2a/0x170
[  256.160407]
[  256.160407] which lock already depends on the new lock.
[  256.160407]
[  256.168712]
[  256.168712] the existing dependency chain (in reverse order) is:
[  256.176327]
[  256.176327] -> #1 (misc_mtx){+.+.}-{3:3}:
[  256.181946]        lock_acquire+0x1e6/0x330
[  256.186265]        __mutex_lock+0x9b/0x9b0
[  256.190497]        mutex_lock_nested+0x1b/0x20
[  256.195075]        misc_register+0x32/0x1a0
[  256.199390]        isst_if_cdev_register+0x65/0x180 [isst_if_common]
[  256.205878]        isst_if_probe+0x144/0x16e [isst_if_mmio]
...
[  256.241976]
[  256.241976] -> #0 (punit_misc_dev_lock){+.+.}-{3:3}:
[  256.248552]        validate_chain+0xbc6/0x1750
[  256.253131]        __lock_acquire+0x88c/0xc10
[  256.257618]        lock_acquire+0x1e6/0x330
[  256.261933]        __mutex_lock+0x9b/0x9b0
[  256.266165]        mutex_lock_nested+0x1b/0x20
[  256.270739]        isst_if_open+0x18/0x90 [isst_if_common]
[  256.276356]        misc_open+0x100/0x170
[  256.280409]        chrdev_open+0xa5/0x1e0
...

The call sequence suggested that misc_device /dev file can be opened
before misc device is yet to be registered, which is done only once.

Here punit_misc_dev_lock was used as common lock, to protect the
registration by multiple ISST HW drivers, one time setup, prevent
duplicate registry of misc device and prevent load/unload when device
is open.

We can split into locks:
- One which just prevent duplicate call to misc_register() and one
time setup. Also never call again if the misc_register() failed or
required one time setup is failed. This lock is not shared with
any misc device callbacks.

- The other lock protects registry, load and unload of HW drivers.

Sequence in isst_if_cdev_register()
- Register callbacks under punit_misc_dev_open_lock
- Call isst_misc_reg() which registers misc_device on the first
registry which is under punit_misc_dev_reg_lock, which is not
shared with callbacks.

Sequence in isst_if_cdev_unregister
Just opposite of isst_if_cdev_register

Reported-and-tested-by: Liwei Song <liwei.song@windriver.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20220112022521.54669-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: touchscreen_dmi: Add info for the RWC NANOTE P8 AY07J 2-in-1

[ Upstream commit 512eb73cfd1208898cf10cb06094e0ee0bb53b58 ]

Add touchscreen info for RWC NANOTE P8 (AY07J) 2-in-1.

Signed-off-by: Yuka Kawajiri <yukx00@gmail.com>
Link: https://lore.kernel.org/r/20220111154019.4599-1-yukx00@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

btrfs: send: in case of IO error log it

commit 2e7be9db125a0bf940c5d65eb5c40d8700f738b5 upstream.

Currently if we get IO error while doing send then we abort without
logging information about which file caused issue.  So log it to help
with debugging.

CC: stable@vger.kernel.org # 4.9+
Signed-off-by: Dāvis Mosāns <davispuh@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Add ioread64_lo_hi() and iowrite64_lo_hi()

commit 18a1d5e1945385d9b5adc3fe11427ce4a9d2826e upstream.

It's a followup to the previous commit f15309d7ad5d ("parisc: Add
ioread64_hi_lo() and iowrite64_hi_lo()") which does only half of
the job. Add the rest, so we won't get a new kernel test robot
reports.

Fixes: f15309d7ad5d ("parisc: Add ioread64_hi_lo() and iowrite64_hi_lo()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI: hv: Fix NUMA node assignment when kernel boots with custom NUMA topology

commit 3149efcdf2c6314420c418dfc94de53bfd076b1f upstream.

When kernel boots with a NUMA topology with some NUMA nodes offline, the PCI
driver should only set an online NUMA node on the device. This can happen
during KDUMP where some NUMA nodes are not made online by the KDUMP kernel.

This patch also fixes the case where kernel is booting with "numa=off".

Fixes: 999dd956d838 ("PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Purna Pavan Chandra Aekkaladevi <paekkaladevi@microsoft.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/1643247814-15184-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm: don't try to NUMA-migrate COW pages that have other uses

commit 80d47f5de5e311cbc0d01ebb6ee684e8f4c196c6 upstream.

Oded Gabbay reports that enabling NUMA balancing causes corruption with
his Gaudi accelerator test load:

 "All the details are in the bug, but the bottom line is that somehow,
  this patch causes corruption when the numa balancing feature is
  enabled AND we don't use process affinity AND we use GUP to pin pages
  so our accelerator can DMA to/from system memory.

  Either disabling numa balancing, using process affinity to bind to
  specific numa-node or reverting this patch causes the bug to
  disappear"

and Oded bisected the issue to commit 09854ba94c6a ("mm: do_wp_page()
simplification").

Now, the NUMA balancing shouldn't actually be changing the writability
of a page, and as such shouldn't matter for COW.  But it appears it
does.  Suspicious.

However, regardless of that, the condition for enabling NUMA faults in
change_pte_range() is nonsensical.  It uses "page_mapcount(page)" to
decide if a COW page should be NUMA-protected or not, and that makes
absolutely no sense.

The number of mappings a page has is irrelevant: not only does GUP get a
reference to a page as in Oded's case, but the other mappings migth be
paged out and the only reference to them would be in the page count.

Since we should never try to NUMA-balance a page that we can't move
anyway due to other references, just fix the code to use 'page_count()'.
Oded confirms that that fixes his issue.

Now, this does imply that something in NUMA balancing ends up changing
page protections (other than the obvious one of making the page
inaccessible to get the NUMA faulting information).  Otherwise the COW
simplification wouldn't matter - since doing the GUP on the page would
make sure it's writable.

The cause of that permission change would be good to figure out too,
since it clearly results in spurious COW events - but fixing the
nonsensical test that just happened to work before is obviously the
CorrectThing(tm) to do regardless.

Fixes: 09854ba94c6a ("mm: do_wp_page() simplification")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215616
Link: https://lore.kernel.org/all/CAFCwf10eNmwq2wD71xjUhqkvv5+_pJMR1nPug2RqNDcFT4H86Q@mail.gmail.com/
Reported-and-tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: block: fix read single on recovery logic

commit 54309fde1a352ad2674ebba004a79f7d20b9f037 upstream.

On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.

On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.

Fixes: 81196976ed946c ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix sglist access in ccio-dma.c

commit d7da660cab47183cded65e11b64497d0f56c6edf upstream.

This patch implements the same bug fix to ccio-dma.c as to sba_iommu.c.
It ensures that only the allocated entries of the sglist are accessed.

Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix data TLB miss in sba_unmap_sg

commit b7d6f44a0fa716a82969725516dc0b16bc7cd514 upstream.

Rolf Eike Beer reported the following bug:

[1274934.746891] Bad Address (null pointer deref?): Code=15 (Data TLB miss fault) at addr 0000004140000018
[1274934.746891] CPU: 3 PID: 5549 Comm: cmake Not tainted 5.15.4-gentoo-parisc64 #4
[1274934.746891] Hardware name: 9000/785/C8000
[1274934.746891]
[1274934.746891]      YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
[1274934.746891] PSW: 00001000000001001111111000001110 Not tainted
[1274934.746891] r00-03  000000ff0804fe0e 0000000040bc9bc0 00000000406760e4 0000004140000000
[1274934.746891] r04-07  0000000040b693c0 0000004140000000 000000004a2b08b0 0000000000000001
[1274934.746891] r08-11  0000000041f98810 0000000000000000 000000004a0a7000 0000000000000001
[1274934.746891] r12-15  0000000040bddbc0 0000000040c0cbc0 0000000040bddbc0 0000000040bddbc0
[1274934.746891] r16-19  0000000040bde3c0 0000000040bddbc0 0000000040bde3c0 0000000000000007
[1274934.746891] r20-23  0000000000000006 000000004a368950 0000000000000000 0000000000000001
[1274934.746891] r24-27  0000000000001fff 000000000800000e 000000004a1710f0 0000000040b693c0
[1274934.746891] r28-31  0000000000000001 0000000041f988b0 0000000041f98840 000000004a171118
[1274934.746891] sr00-03  00000000066e5800 0000000000000000 0000000000000000 00000000066e5800
[1274934.746891] sr04-07  0000000000000000 0000000000000000 0000000000000000 0000000000000000
[1274934.746891]
[1274934.746891] IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000406760e8 00000000406760ec
[1274934.746891]  IIR: 48780030    ISR: 0000000000000000  IOR: 0000004140000018
[1274934.746891]  CPU:        3   CR30: 00000040e3a9c000 CR31: ffffffffffffffff
[1274934.746891]  ORIG_R28: 0000000040acdd58
[1274934.746891]  IAOQ[0]: sba_unmap_sg+0xb0/0x118
[1274934.746891]  IAOQ[1]: sba_unmap_sg+0xb4/0x118
[1274934.746891]  RP(r2): sba_unmap_sg+0xac/0x118
[1274934.746891] Backtrace:
[1274934.746891]  [<00000000402740cc>] dma_unmap_sg_attrs+0x6c/0x70
[1274934.746891]  [<000000004074d6bc>] scsi_dma_unmap+0x54/0x60
[1274934.746891]  [<00000000407a3488>] mptscsih_io_done+0x150/0xd70
[1274934.746891]  [<0000000040798600>] mpt_interrupt+0x168/0xa68
[1274934.746891]  [<0000000040255a48>] __handle_irq_event_percpu+0xc8/0x278
[1274934.746891]  [<0000000040255c34>] handle_irq_event_percpu+0x3c/0xd8
[1274934.746891]  [<000000004025ecb4>] handle_percpu_irq+0xb4/0xf0
[1274934.746891]  [<00000000402548e0>] generic_handle_irq+0x50/0x70
[1274934.746891]  [<000000004019a254>] call_on_stack+0x18/0x24
[1274934.746891]
[1274934.746891] Kernel panic - not syncing: Bad Address (null pointer deref?)

The bug is caused by overrunning the sglist and incorrectly testing
sg_dma_len(sglist) before nents. Normally this doesn't cause a crash,
but in this case sglist crossed a page boundary. This occurs in the
following code:

while (sg_dma_len(sglist) && nents--) {

The fix is simply to test nents first and move the decrement of nents
into the loop.

Reported-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Drop __init from map_pages declaration

commit 9129886b88185962538180625ca8051362b01327 upstream.

With huge kernel pages, we randomly eat a SPARC in map_pages(). This
is fixed by dropping __init from the declaration.

However, map_pages references the __init routine memblock_alloc_try_nid
via memblock_alloc.  Thus, it needs to be marked with __ref.

memblock_alloc is only called before the kernel text is set to readonly.

The __ref on free_initmem is no longer needed.

Comment regarding map_pages being in the init section is removed.

Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: parisc: GSC: fix build when IOSAPIC is not set

commit 6e8793674bb0d1135ca0e5c9f7e16fecbf815926 upstream.

There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:

hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'

when:
  CONFIG_GSC=y
  CONFIG_SERIO_GSCPS2=y
  CONFIG_SERIAL_8250_GSC=y
  CONFIG_PCI is not set
    and hence PCI_LBA is not set.
  IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.

Make the use of iosapic_serial_irq() conditional to fix the build error.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "svm: Add warning message for AVIC IPI invalid target"

commit dd4589eee99db8f61f7b8f7df1531cad3f74a64d upstream.

Remove a WARN on an "AVIC IPI invalid target" exit, the WARN is trivial
to trigger from guest as it will fail on any destination APIC ID that
doesn't exist from the guest's perspective.

Don't bother recording anything in the kernel log, the common tracepoint
for kvm_avic_incomplete_ipi() is sufficient for debugging.

This reverts commit 37ef0c4414c9743ba7f1af4392f0a27a99649f2a.

Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220204214205.3306634-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID:Add support for UGTABLET WP5540

commit fd5dd6acd8f823ea804f76d3af64fa1be9d5fb78 upstream.

This patch adds support for the UGTABLET WP5540 digitizer tablet
devices. Without it, the pen moves the cursor, but neither the
buttons nor the tap sensor in the tip do work.

Signed-off-by: Sergio Costas <rastersoft@gmail.com>
Link: https://lore.kernel.org/r/63dece1d-91ca-1b1b-d90d-335be66896be@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: lpfc: Fix mailbox command failure during driver initialization

commit efe1dc571a5b808baa26682eef16561be2e356fd upstream.

Contention for the mailbox interface may occur during driver initialization
(immediately after a function reset), between mailbox commands initiated
via ioctl (bsg) and those driver requested by the driver.

After setting SLI_ACTIVE flag for a port, there is a window in which the
driver will allow an ioctl to be initiated while the adapter is
initializing and issuing mailbox commands via polling. The polling logic
then gets confused.

Correct by having thread setting SLI_ACTIVE spot an active mailbox command
and allow it complete before proceeding.

Link: https://lore.kernel.org/r/20210921143008.64212-1-jsmart2021@gmail.com
Co-developed-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>