Dinesh Karthikeyan [Fri, 15 Nov 2024 06:28:53 +0000 (11:58 +0530)]
wifi: ath12k: Support SoC Common Stats
Add support to request SoC stat from firmware through HTT stat
type 38. This stat gives drop count of SoC.
Note: MCC firmware version -
WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 does not
support tag HTT_STATS_SOC_TXRX_STATS_COMMON_TAG(125).
Sample output:
-------------
echo 38 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_SOC_COMMON_STATS_TLV:
soc_drop_count = 0x0000000000000000
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241115062854.1919672-4-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Dinesh Karthikeyan [Fri, 15 Nov 2024 06:28:52 +0000 (11:58 +0530)]
wifi: ath12k: Support phy counter and TPC stats
Add support to request counters and Transmission Power Control
(TPC) stats through HTT stats type 37. These stats give
information about counters like received packet count, CRC pass
count, error count, transmit abort count, etc., about counter reset
like reset cause, channel frequency, number and mode, channel flags,
etc., about TPC like transmit power scale, maximum transmit power,
gain cap, EIRP, etc.
Note: MCC firmware version -
WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 does not
support HTT stats type 37, i.e., the firmware does not respond to the
command requesting stats.
Sample output:
-------------
echo 37 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_PHY_STATS_TLV:
bdf_nf_chain[0] = -92
bdf_nf_chain[1] = -94
bdf_nf_chain[2] = -94
bdf_nf_chain[3] = -93
.....
HTT_PHY_COUNTERS_TLV:
rx_ofdma_timing_err_cnt = 18068
rx_cck_fail_cnt = 0
mactx_abort_cnt = 2612
macrx_abort_cnt = 0
.....
HTT_PHY_RESET_STATS_TLV:
pdev_id = 0
chan_mhz = 0
chan_band_center_freq1 = 0
chan_band_center_freq2 = 0
.....
HTT_PHY_RESET_COUNTERS_TLV:
pdev_id = 0
cf_active_low_fail_cnt = 0
cf_active_low_pass_cnt = 0
phy_off_through_vreg_cnt = 0
.....
HTT_PHY_TPC_STATS_TLV:
pdev_id = 0
tx_power_scale = 0
tx_power_scale_db = 0
min_negative_tx_power = 0
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241115062854.1919672-3-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Dinesh Karthikeyan [Fri, 15 Nov 2024 06:28:51 +0000 (11:58 +0530)]
wifi: ath12k: Support Downlink Pager Stats
Add support to request downlink pager stats from firmware through HTT
stats type 36. These stats give paging information like number of pages,
their timestamp, number of locked and free pages, synchronous and
asynchronous locked pages.
Note: MCC firmware version -
WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 responds to
the event requesting stats, but it does not give any data.
Sample output:
-------------
echo 36 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_DLPAGER_STATS_TLV:
ASYNC locked pages = 2
SYNC locked pages = 0
Total locked pages = 2
Total free pages = 127
LOCKED PAGES HISTORY
last_locked_page_idx = 0
Index - 0 ; Page Number - 8495 ; Num of pages - 1 ; Timestamp - 4031009360us
Index - 1 ; Page Number - 7219 ; Num of pages - 2 ; Timestamp - 885379515us
Index - 2 ; Page Number - 0 ; Num of pages - 0 ; Timestamp - 0us
Index - 3 ; Page Number - 0 ; Num of pages - 0 ; Timestamp - 0us
.....
UNLOCKED PAGES HISTORY
last_unlocked_page_idx = 0
Index - 0 ; Page Number - 7144 ; Num of pages - 2 ; Timestamp - 4032070008us
Index - 1 ; Page Number - 7214 ; Num of pages - 2 ; Timestamp - 885379512us
Index - 2 ; Page Number - 0 ; Num of pages - 0 ; Timestamp - 0us
Index - 3 ; Page Number - 0 ; Num of pages - 0 ; Timestamp - 0us
.....
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241115062854.1919672-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Toke Høiland-Jørgensen [Wed, 6 Nov 2024 12:41:44 +0000 (13:41 +0100)]
wifi: ath9k: Add RX inactivity detection and reset chip when it occurs
Some ath9k chips can, seemingly at random, end up in a state which can
be described as "deaf". No or nearly no interrupts are generated anymore
for incoming packets. Existing links either break down after a while and
new links will not be established.
The circumstances leading to this "deafness" is still unclear, but some
particular chips (especially 2-stream 11n SoCs, but also others) can go
'deaf' when running AP or mesh (or both) after some time. It's probably
a hardware issue, and doing a channel scan to trigger a chip
reset (which one normally can't do on an AP interface) recovers the
hardware.
The only way the driver can detect this state, is by detecting if there
has been no RX activity for a while. In this case we can proactively
reset the chip (which only takes a small number of milliseconds, so
shouldn't interrupt things too much if it has been idle for several
seconds), which functions as a workaround.
OpenWrt, and various derivatives, have been carrying versions of this
workaround for years, that were never upstreamed. One version[0],
written by Felix Fietkau, used a simple counter and only reset if there
was precisely zero RX activity for a long period of time. This had the
problem that in some cases a small number of interrupts would appear
even if the device was otherwise not responsive. For this reason,
another version[1], written by Simon Wunderlich and Sven Eckelmann, used
a time-based approach to calculate the average number of RX interrupts
over a longer (four-second) interval, and reset the chip when seeing
less than one interrupt per second over this period. However, that
version relied on debugfs counters to keep track of the number of
interrupts, which means it didn't work at all if debugfs was not
enabled.
This patch unifies the two versions: it uses the same approach as Felix'
patch to count the number of RX handler invocations, but uses the same
time-based windowing approach as Simon and Sven's patch to still handle
the case where occasional interrupts appear but the device is otherwise
deaf.
Since this is based on ideas by all three people, but not actually
directly derived from any of the patches, I'm including Suggested-by
tags from Simon, Sven and Felix below, which should hopefully serve as
proper credit.
[0] https://patchwork.kernel.org/project/linux-wireless/patch/
20170125163654.66431-3-nbd@nbd.name/
[1] https://patchwork.kernel.org/project/linux-wireless/patch/
20161117083614.19188-2-sven.eckelmann@open-mesh.com/
Suggested-by: Simon Wunderlich <sw@simonwunderlich.de>
Suggested-by: Sven Eckelmann <se@simonwunderlich.de>
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Tested-by: Sven Eckelmann <se@simonwunderlich.de>
Reviewed-by: Sven Eckelmann <se@simonwunderlich.de>
Tested-by: Issam Hamdi <ih@simonwunderlich.de>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Link: https://patch.msgid.link/20241106-ath9k-deaf-detection-v1-1-736a150d2425@redhat.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Balaji Pothunoori [Wed, 30 Oct 2024 11:46:25 +0000 (17:16 +0530)]
wifi: ath11k: Fix unexpected return buffer manager error for WCN6750/WCN6855
The following error messages were encountered while parsing fragmented RX
packets for WCN6750/WCN6855:
ath11k
17a10040.wifi: invalid return buffer manager 4
This issue arose due to a hardcoded check for HAL_RX_BUF_RBM_SW3_BM
introduced in 'commit
71c748b5e01e ("ath11k: Fix unexpected return buffer
manager error for QCA6390")'
For WCN6750 and WCN6855, the return buffer manager ID should be
HAL_RX_BUF_RBM_SW1_BM. The incorrect conditional check caused fragmented
packets to be dropped, resulting in the above error log.
Fix this by adding a check for HAL_RX_BUF_RBM_SW1_BM.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00258-QCAMSLSWPL-1
Tested-on: WCN6855 hw2.1 WLAN.HSP.1.1-04479-QCAHSPSWPL_V1_V2_SILICONZ_IOE-1
Fixes:
71c748b5e01e ("ath11k: Fix unexpected return buffer manager error for QCA6390")
Signed-off-by: Balaji Pothunoori <quic_bpothuno@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241030114625.2416942-1-quic_bpothuno@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Karol Przybylski [Tue, 5 Nov 2024 10:11:31 +0000 (11:11 +0100)]
wifi: ath12k: Fix for out-of bound access error
Selfgen stats are placed in a buffer using print_array_to_buf_index() function.
Array length parameter passed to the function is too big, resulting in possible
out-of bound memory error.
Decreasing buffer size by one fixes faulty upper bound of passed array.
Discovered in coverity scan, CID
1600742 and CID
1600758
Signed-off-by: Karol Przybylski <karprzy7@gmail.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241105101132.374372-1-karprzy7@gmail.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Dmitry Antipov [Mon, 11 Nov 2024 10:47:24 +0000 (13:47 +0300)]
wifi: ath9k: miscellaneous spelling fixes
Correct spelling here and there as suggested by codespell.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20241111104724.484586-1-dmantipov@yandex.ru
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Sriram R [Fri, 1 Nov 2024 15:17:05 +0000 (17:17 +0200)]
wifi: ath12k: Add MLO peer assoc command support
Add changes to send MLO peer assoc command with partner link details and
primary umac details.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-9-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Sriram R [Fri, 1 Nov 2024 15:17:04 +0000 (17:17 +0200)]
wifi: ath12k: add helper to find multi-link station
Multi-link stations are identified in driver using the multi-link
peer id and they have ATH12K_PEER_ML_ID_VALID bit set in the id. Add a helper
to find multi-link station using the multi-link peer id.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Sriram R [Fri, 1 Nov 2024 15:17:03 +0000 (17:17 +0200)]
wifi: ath12k: add multi-link flag in peer create command
Driver should indicate to firmware whether a peer is multi-link or not in peer
create command using multi-link flag. Add changes to support
WMI_TAG_MLO_PEER_CREATE_PARAMS in WMI_PEER_CREATE_CMDID.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Sriram R [Fri, 1 Nov 2024 15:17:02 +0000 (17:17 +0200)]
wifi: ath12k: Add helpers for multi link peer creation and deletion
Add helper functions for multi link peer addition and deletion. And add address
validation to ensure we are not creating link peers (belonging to different
clients) with same MLD address. To aid in this validation for faster lookup,
add a new list of ML peers to struct ath12k_hw::ml_peers and use the same for
parsing for the above address validation use cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Kalle Valo [Fri, 1 Nov 2024 15:17:01 +0000 (17:17 +0200)]
wifi: ath12k: introduce ath12k_hw_warn()
In the following patch we need to use ath12k_warn() but don't easily have
access to struct ath12k_base (ab) but do have access to struct ath12k_hw (ah).
So add a new warning helper ath12_hw_warn() which takes the latter but the log
output is still identical but uses the struct device pointer stored to struct
ath12k_hw.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Sriram R [Fri, 1 Nov 2024 15:17:00 +0000 (17:17 +0200)]
wifi: ath12k: Refactor sta state machine
Refactor ath12k_mac_op_sta_state(), with generic wrappers which can be used for
both multi link stations and non-ML stations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Sriram R [Fri, 1 Nov 2024 15:16:59 +0000 (17:16 +0200)]
wifi: ath12k: MLO vdev bringup changes
Add changes to add the link vdevs dynamically whenever a channel is assigned
from mac80211 for a link vdev. During vdev create, update ML address of the
vdev to firmware using the new WMI parameter (WMI_TAG_MLO_VDEV_CREATE_PARAMS).
During vdev start, notify the firmware that this link vdev is newly added and
also indicate all its known partners so that the firmware can take necessary
actions to internally update the partners on the new link being added.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Kalle Valo [Fri, 1 Nov 2024 15:16:58 +0000 (17:16 +0200)]
wifi: ath12k: ath12k_mac_vdev_create(): use goto for error handling
In commit
477cabfdb776 ("wifi: ath12k: modify link arvif creation and removal
for MLO") I had accidentally left one personal TODO comment about using goto
instead of ret. Switch to use goto to be consistent with the error handling in
the function.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Jeff Johnson [Mon, 28 Oct 2024 14:08:40 +0000 (07:08 -0700)]
wifi: ath12k: mark QMI driver event helpers as noinline
As described in [1], compiling the ath12k driver using clang with
KASAN enabled warns about some functions with excessive stack usage,
with the worst case being:
drivers/net/wireless/ath/ath12k/qmi.c:3546:13: warning: stack frame size (2456) exceeds limit (1024) in 'ath12k_qmi_driver_event_work' [-Wframe-larger-than]
Nathan [2] highlighted work done by Arnd [3] to address similar
issues in other portions of the kernel.
ath12k_qmi_driver_event_work() itself is a pretty lightweight
function, but it dispatches to several other functions which do the
real work:
ath12k_qmi_driver_event_work()
ath12k_qmi_event_server_arrive()
ath12k_qmi_host_cap_send()
ath12k_qmi_event_mem_request()
ath12k_qmi_respond_fw_mem_request()
ath12k_qmi_event_load_bdf()
ath12k_qmi_request_target_cap()
ath12k_qmi_load_bdf_qmi()
ath12k_qmi_wlanfw_m3_info_send()
Mark all of those underlying functions as 'noinline_for_stack' to
prevent them from being inlined in ath12k_qmi_driver_event_work(),
thereby eliminating the excessive stack usage.
Link: https://msgid.link/bc214795-1c51-4cb7-922f-67d6ef98bff2@quicinc.com
Link: https://msgid.link/20241025223321.GA3647469@thelio-3990X
Link: https://lore.kernel.org/all/?q=f:arnd@kernel.org+Wframe-larger-than
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241028-ath12k_qmi_driver_event_work-v1-1-0d532eb593fa@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Balaji Pothunoori [Tue, 29 Oct 2024 08:33:40 +0000 (14:03 +0530)]
wifi: ath11k: Suspend hardware before firmware mode off for WCN6750
During rmmod, the ath11k host driver sends a QMI MODE OFF command
to firmware.
As part of this command, firmware initiates WLAN de-initialization
and accesses certain UMAC registers during this process.
Currently, on WCN6750 WLAN hardware, the system is in a sleep state when
firmware receives the QMI MODE OFF command.
This results in a firmware/hardware reset while accessing the UMAC hardware
registers during sleep state.
To avoid this, add logic to send WCN6750 hardware specific
WMI_PDEV_SUSPEND_AND_DISABLE_INTR command to firmware prior to sending
the QMI MODE OFF command.
This will cause firmware to cease all activities and put the device in
a powered-on state that prevents access to registers which have been
powered off.
Signed-off-by: Balaji Pothunoori <quic_bpothuno@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241029083340.3010798-1-quic_bpothuno@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Linus Walleij [Mon, 28 Oct 2024 22:06:53 +0000 (23:06 +0100)]
wifi: cw1200: Fix potential NULL dereference
A recent refactoring was identified by static analysis to
cause a potential NULL dereference, fix this!
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/
202410121505.nyghqEkK-lkp@intel.com/
Fixes:
2719a9e7156c ("wifi: cw1200: Convert to GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241028-cw1200-fix-v1-1-e092b6558d1e@linaro.org
Dr. David Alan Gilbert [Fri, 25 Oct 2024 20:46:51 +0000 (21:46 +0100)]
wifi: brcm80211: Remove unused dma_txflush()
dma_fxflush() has been unused since 2013's
commit
7b2385b95363 ("brcmsmac: rework of mac80211 .flush() callback
operation")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241025204651.244627-1-linux@treblig.org
Yuan Can [Tue, 22 Oct 2024 09:04:53 +0000 (17:04 +0800)]
wifi: wfx: Fix error handling in wfx_core_init()
The wfx_core_init() returns without checking the retval from
sdio_register_driver().
If the sdio_register_driver() failed, the module failed to install,
leaving the wfx_spi_driver not unregistered.
Fixes:
a7a91ca5a23d ("staging: wfx: add infrastructure for new driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241022090453.84679-1-yuancan@huawei.com
Kalle Valo [Thu, 31 Oct 2024 14:03:57 +0000 (16:03 +0200)]
Merge tag 'ath-next-
20241030' of git://git./linux/kernel/git/ath/ath
ath.git patches for v6.13
This development cycle featured phase 1 of patches to ath12k to
support the new 802.11be MLO feature, along with other ath12k feature
patches. In older drivers, support for some additional devices were
added. And there was the usual set of bug fixes and cleanups across
most drivers.
Per-driver highlights:
ath12k
* Switch to using wiphy_lock() and remove ar->conf_mutex
* Convert struct ath12k_sta::update_wk to use struct wiphy_work
* Add phase 1 of 802.11be MLO support
* Add firmware coredump collection support
* Add debugfs support for a multitude of statistics
* Fix host representation of multiple hal_rx structs
* Fix use-after-free in ath12k_dp_cc_cleanup()
* Skip Rx TID cleanup for self peer
* Fix warning and crash when unloading in a VM
* Convert CE interrupt handling from tasklet to BH workqueue
* Fix A-MSDU indication in monitor mode
ath11k
* Fix double free issue during SRNG deinit
* Enable firmware diagnostic events for WCN6750
* Fix CE offset address calculation for WCN6750 during SSR
* Fix stack frame size warning in ath11k_vif_wow_set_wakeups()
* Document the inputs for ath11k on WCN6855
ath10k
* Fix multiple stack frame size warnings
* Fix invalid VHT parameters in supported_vht_mcs_rate_nss* structs
* Avoid NULL pointer error during SDIO remove
ath5k
* Add support for Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A
Kory Maincent [Mon, 28 Oct 2024 13:23:51 +0000 (14:23 +0100)]
Documentation: networking: Add missing PHY_GET command in the message list
ETHTOOL_MSG_PHY_GET/GET_REPLY/NTF is missing in the ethtool message list.
Add it to the ethool netlink documentation.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241028132351.75922-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 30 Oct 2024 01:50:57 +0000 (18:50 -0700)]
Merge tag 'wireless-next-2024-10-25' of git://git./linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.13
The first -next "new features" pull request for v6.13. This is a big
one as we have not been able to send one earlier. We have also some
patches affecting other subsystems: in staging we deleted the rtl8192e
driver and in debugfs added a new interface to save struct
file_operations memory; both were acked by GregKH.
Because of the lib80211/libipw move there were quite a lot of
conflicts and to solve those we decided to merge net-next into
wireless-next.
Major changes:
cfg80211/mac80211
* stop exporting wext symbols
* new mac80211 op to indicate that a new interface is to be added
* support radio separation of multi-band devices
Wireless Extensions
* move wext spy implementation to libiw
* remove iw_public_data from struct net_device
brcmfmac
* optional LPO clock support
ipw2x00
* move remaining lib80211 code into libiw
wilc1000
* WILC3000 support
rtw89
* RTL8852BE and RTL8852BE-VT BT-coexistence improvements
* tag 'wireless-next-2024-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (126 commits)
mac80211: Remove NOP call to ieee80211_hw_config
wifi: iwlwifi: work around -Wenum-compare-conditional warning
wifi: mac80211: re-order assigning channel in activate links
wifi: mac80211: convert debugfs files to short fops
debugfs: add small file operations for most files
wifi: mac80211: remove misleading j_0 construction parts
wifi: mac80211_hwsim: use hrtimer_active()
wifi: mac80211: refactor BW limitation check for CSA parsing
wifi: mac80211: filter on monitor interfaces based on configured channel
wifi: mac80211: refactor ieee80211_rx_monitor
wifi: mac80211: add support for the monitor SKIP_TX flag
wifi: cfg80211: add monitor SKIP_TX flag
wifi: mac80211: add flag to opt out of virtual monitor support
wifi: cfg80211: pass net_device to .set_monitor_channel
wifi: mac80211: remove status->ampdu_delimiter_crc
wifi: cfg80211: report per wiphy radio antenna mask
wifi: mac80211: use vif radio mask to limit creating chanctx
wifi: mac80211: use vif radio mask to limit ibss scan frequencies
wifi: cfg80211: add option for vif allowed radios
wifi: iwlwifi: allow IWL_FW_CHECK() with just a string
...
====================
Link: https://patch.msgid.link/20241025170705.5F6B2C4CEC3@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 29 Oct 2024 23:52:59 +0000 (16:52 -0700)]
Merge branch 'devlink-minor-cleanup'
Przemek Kitszel says:
====================
devlink: minor cleanup
(Patch 1, 2) Add one helper shortcut to put u64 values into skb.
(Patch 3, 4) Minor cleanup for error codes.
(Patch 5, 6, 7) Remove some devlink_resource_*() usage and functions
itself via replacing devlink_* variants by devl_* ones.
v2: fix metadata (cc list, target tree) - Jiri; rebase; tags collected
v1: https://lore.kernel.org/
20241018102009.10124-1-przemyslaw.kitszel@intel.com
====================
Link: https://patch.msgid.link/20241023131248.27192-1-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:07 +0000 (15:09 +0200)]
devlink: remove unused devlink_resource_register()
Remove unused devlink_resource_register(); all the drivers use
devl_resource_register() variant instead.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-8-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:06 +0000 (15:09 +0200)]
devlink: remove unused devlink_resource_occ_get_register() and _unregister()
Remove not used devlink_resource_occ_get_register() and
devlink_resource_occ_get_unregister() functions; current devlink resource
users are fine with devl_ variants of the two.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-7-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:05 +0000 (15:09 +0200)]
net: dsa: replace devlink resource registration calls by devl_ variants
Replace devlink_resource_register(), devlink_resource_occ_get_register(),
and devlink_resource_occ_get_unregister() calls by respective devl_*
variants. Mentioned functions have no direct users in any drivers, and are
going to be removed in subsequent patches.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-6-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:04 +0000 (15:09 +0200)]
devlink: region: snapshot IDs: consolidate error values
Consolidate error codes for too big message size.
Current code is written to return -EINVAL when tailroom in the skb msg
would be exhausted precisely when it's time to nest, and return -EMSGSIZE
in all other "not enough space" conditions.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-5-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:03 +0000 (15:09 +0200)]
devlink: devl_resource_register(): differentiate error codes
Differentiate error codes of devl_resource_register().
Replace one of -EINVAL exit paths by -EEXIST. This should aid developers
introducing new resources and registering them in the wrong order.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-4-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:02 +0000 (15:09 +0200)]
devlink: use devlink_nl_put_u64() helper
Use devlink_nl_put_u64() shortcut added by prev commit on all devlink/.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-3-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Przemek Kitszel [Wed, 23 Oct 2024 13:09:01 +0000 (15:09 +0200)]
devlink: introduce devlink_nl_put_u64()
Add devlink_nl_put_u64() that abstracts padding for u64 values.
All u64 values are passed with the very same padding option.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20241023131248.27192-2-przemyslaw.kitszel@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Thu, 24 Oct 2024 20:48:59 +0000 (22:48 +0200)]
r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
This fixes an inconsistent indenting introduced with
e3fc5139bd8f
("r8169: implement additional ethtool stats ops").
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/
202410220413.1gAxIJ4t-lkp@intel.com/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20fd6f39-3c1b-4af0-9adc-7d1f49728fad@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima [Thu, 24 Oct 2024 20:14:58 +0000 (13:14 -0700)]
socket: Print pf->create() when it does not clear sock->sk on failure.
I suggested to put DEBUG_NET_WARN_ON_ONCE() in __sock_create() to
catch possible use-after-free.
But the warning itself was not useful because our interest is in
the callee than the caller.
Let's define DEBUG_NET_WARN_ONCE() and print the name of pf->create()
and the socket identifier.
While at it, we enclose DEBUG_NET_WARN_ON_ONCE() in parentheses too
to avoid a checkpatch error.
Note that %pf or %pF were obsoleted and will be removed later as per
comment in lib/vsprintf.c.
Link: https://lore.kernel.org/netdev/202410231427.633734b3-lkp@intel.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241024201458.49412-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Thu, 24 Oct 2024 20:42:33 +0000 (22:42 +0200)]
r8169: add support for RTL8125D
This adds support for new chip version RTL8125D, which can be found on
boards like Gigabyte X870E AORUS ELITE WIFI7. Firmware rtl8125d-1.fw
for this chip version is available in linux-firmware already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d0306912-e88e-4c25-8b5d-545ae8834c0c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rosen Penev [Thu, 24 Oct 2024 19:55:34 +0000 (12:55 -0700)]
net: qlogic: use ethtool string helpers
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the pointer. Cleans up the code quite well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241024195534.176410-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rosen Penev [Thu, 24 Oct 2024 19:58:33 +0000 (12:58 -0700)]
net: marvell: use ethtool string helpers
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the pointer. Cleans up the code quite well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241024195833.176843-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Caleb Sander Mateos [Wed, 23 Oct 2024 20:51:12 +0000 (14:51 -0600)]
mlx5: simplify EQ interrupt polling logic
Use a while loop in mlx5_eq_comp_int() and mlx5_eq_async_int() to
clarify the EQE polling logic. This consolidates the next_eqe_sw() calls
for the first and subequent iterations. It also avoids a goto. Turn the
num_eqes < MLX5_EQ_POLLING_BUDGET check into a break condition.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241023205113.255866-1-csander@purestorage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Caleb Sander Mateos [Wed, 23 Oct 2024 16:48:38 +0000 (10:48 -0600)]
mlx5: fix typo in "mlx5_cqwq_get_cqe_enahnced_comp"
"enahnced" looks to be a misspelling of "enhanced".
Rename "mlx5_cqwq_get_cqe_enahnced_comp" to
"mlx5_cqwq_get_cqe_enhanced_comp".
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20241023164840.140535-1-csander@purestorage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rosen Penev [Tue, 22 Oct 2024 23:32:03 +0000 (16:32 -0700)]
amd-xgbe: use ethtool string helpers
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the pointer.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241022233203.9670-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rosen Penev [Tue, 22 Oct 2024 20:49:08 +0000 (13:49 -0700)]
net: mana: use ethtool string helpers
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the data pointer.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Link: https://patch.msgid.link/20241022204908.511021-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rosen Penev [Tue, 22 Oct 2024 20:32:40 +0000 (13:32 -0700)]
ibmvnic: use ethtool string helpers
They are the preferred way to copy ethtool strings.
Avoids manually incrementing the data pointer.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241022203240.391648-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jacky Chou [Tue, 22 Oct 2024 08:42:14 +0000 (16:42 +0800)]
net: ftgmac100: refactor getting phy device handle
Consolidate the handling of dedicated PHY and fixed-link phy by taking
advantage of logic in of_phy_get_and_connect() which handles both of
these cases, rather than open coding the same logic in ftgmac100_probe().
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241022084214.1261174-1-jacky_chou@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 29 Oct 2024 18:57:35 +0000 (11:57 -0700)]
Merge branch 'net-phylink-simplify-sfp-phy-attachment'
Russell King says:
====================
net: phylink: simplify SFP PHY attachment
These two patches simplify how we attach SFP PHYs.
The first patch notices that at the two sites where we call
sfp_select_interface(), if that fails, we always print the same error.
Move this into its own function.
The second patch adds an additional level of validation, checking that
the returned interface is one that is supported by the MAC/PCS.
The last patch simplifies how SFP PHYs are attached, reducing the
number of times that we do validation in this path.
====================
Link: https://patch.msgid.link/Zxj8_clRmDA_G7uH@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 23 Oct 2024 13:41:57 +0000 (14:41 +0100)]
net: phylink: simplify how SFP PHYs are attached
There are a few issues with how SFP PHYs are attached:
a) The phylink_sfp_connect_phy() and phylink_sfp_config_phy() code
validates the configuration three times:
1. To discover the support/advertising masks that the PHY/PCS/MAC
can support in order to select an interface.
2. To validate the selected interface.
3. When the PHY is brought up after being attached, another validation
is done.
This is needlessly complex.
b) The configuration is set prior to the PHY being attached, which
means we don't have the PHY available in phylink_major_config()
for phylink_pcs_neg_mode() to make decisions upon.
We have already added an extra step to validate the selected interface,
so we can now move the attachment and bringup of the PHY earlier,
inside phylink_sfp_config_phy(). This results in the validation at
step 2 above becoming entirely unnecessary, so remove that too.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcb-000c8H-3e@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 23 Oct 2024 13:41:51 +0000 (14:41 +0100)]
net: phylink: validate sfp_select_interface() returned interface
Validate that the returned interface from sfp_select_interface() is
supportable by the MAC/PCS. If it isn't, print an error and return
the NA interface type. This is a preparatory step to reorganising
how a PHY on a SFP module is handled.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcV-000c8B-Vz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Wed, 23 Oct 2024 13:41:46 +0000 (14:41 +0100)]
net: phylink: add common validation for sfp_select_interface()
Whenever we call sfp_select_interface(), we check the returned value
and print an error. There are two cases where this happens with the
same message. Provide a common function to do this.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcQ-000c85-S4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Tue, 22 Oct 2024 14:17:07 +0000 (15:17 +0100)]
net: phylink: simplify phylink_parse_fixedlink()
phylink_parse_fixedlink() wants to preserve the pause, asym_pause and
autoneg bits in pl->supported. Rather than reading the bits into
separate bools, zeroing pl->supported, and then setting them if they
were previously set, use a mask and linkmode_and() to achieve the same
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1t3Fh5-000aQi-Nk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 29 Oct 2024 18:48:29 +0000 (11:48 -0700)]
Merge branch 'mlx5e-update-features-on-config-changes'
Tariq Toukan says:
====================
mlx5e update features on config changes
This small patchset by Dragos adds a call to netdev_update_features()
in configuration changes that could impact the features status.
====================
Link: https://patch.msgid.link/20241024164134.299646-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dragos Tatulea [Thu, 24 Oct 2024 16:41:33 +0000 (19:41 +0300)]
net/mlx5e: Update features on ring size change
When the ring size changes successfully, trigger
netdev_update_features() to enable features in wanted state if
applicable.
An example of such scenario:
$ ip link set dev eth1 up
$ ethtool --set-ring eth1 rx 8192
$ ip link set dev eth1 mtu 9000
$ ethtool --features eth1 rx-gro-hw on --> fails
$ ethtool --set-ring eth1 rx 1024
With this patch, HW GRO will be turned on automatically because
it is set in the device's wanted_features.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241024164134.299646-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dragos Tatulea [Thu, 24 Oct 2024 16:41:32 +0000 (19:41 +0300)]
net/mlx5e: Update features on MTU change
When the MTU changes successfully, trigger netdev_update_features() to
enable features in wanted state if applicable.
An example of such scenario:
$ ip link set dev eth1 up
$ ethtool --set-ring eth1 rx 8192
$ ip link set dev eth1 mtu 9000
$ ethtool --features eth1 rx-gro-hw on --> fails
$ ip link set dev eth1 mtu 7000
With this patch, HW GRO will be turned on automatically because
it is set in the device's wanted_features.
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241024164134.299646-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon Horman [Wed, 23 Oct 2024 12:15:28 +0000 (13:15 +0100)]
wwan: core: Pass string literal as format argument of dev_set_name()
Both gcc-14 and clang-18 report that passing a non-string literal as the
format argument of dev_set_name() is potentially insecure.
E.g. clang-18 says:
drivers/net/wwan/wwan_core.c:442:34: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
442 | return dev_set_name(&port->dev, buf);
| ^~~
drivers/net/wwan/wwan_core.c:442:34: note: treat the string as an argument to avoid this
442 | return dev_set_name(&port->dev, buf);
| ^
| "%s",
It is always the case where the contents of mod is safe to pass as the
format argument. That is, in my understanding, it never contains any
format escape sequences.
But, it seems better to be safe than sorry. And, as a bonus, compiler
output becomes less verbose by addressing this issue as suggested by
clang-18.
Compile tested only.
No functional change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patch.msgid.link/20241023-wwan-fmt-v1-1-521b39968639@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Karan Sanghavi [Tue, 22 Oct 2024 18:30:52 +0000 (18:30 +0000)]
selftests: tc-testing: Fix typo error
Correct the typo errors in json files
- "diffferent" is corrected to "different".
- "muliple" and "miltiple" is corrected to "multiple".
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Karan Sanghavi <karansanghvi98@gmail.com>
Link: https://patch.msgid.link/20241022-multiple_spell_error-v2-1-7e5036506fe5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima [Tue, 22 Oct 2024 21:03:20 +0000 (14:03 -0700)]
rtnetlink: Fix kdoc of rtnl_af_register().
Commit
26eebdc4b005 ("rtnetlink: Return int from rtnl_af_register().")
made rtnl_af_register() return int again, and kdoc needs to be fixed up.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241022210320.86111-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 29 Oct 2024 18:21:25 +0000 (11:21 -0700)]
Merge branch 'ipv4-prepare-core-ipv4-files-to-future-flowi4_tos-conversion'
Guillaume Nault says:
====================
ipv4: Prepare core ipv4 files to future .flowi4_tos conversion.
Continue preparing users of ->flowi4_tos (struct flowi4) to the future
conversion of this field (from __u8 to dscp_t). The objective is to
have type annotation to properly separate DSCP bits from ECN ones. This
way we'll ensure that ECN doesn't interfere with DSCP and avoid
regressions where it break routing descisions (fib rules in particular).
This series concentrates on some easy IPv4 conversions where
->flowi4_tos is set directly from an IPv4 header, so we can get the
DSCP value using the ip4h_dscp() helper function.
====================
Link: https://patch.msgid.link/cover.1729530028.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Tue, 22 Oct 2024 09:48:23 +0000 (11:48 +0200)]
ipv4: Prepare ip_rt_get_source() to future .flowi4_tos conversion.
Use ip4h_dscp() to get the DSCP from the IPv4 header, then convert the
dscp_t value to __u8 with inet_dscp_to_dsfield().
Then, when we'll convert .flowi4_tos to dscp_t, we'll just have to drop
the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/0a13a200f31809841975e38633914af1061e0c04.1729530028.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Tue, 22 Oct 2024 09:48:15 +0000 (11:48 +0200)]
ipv4: Prepare ipmr_rt_fib_lookup() to future .flowi4_tos conversion.
Use ip4h_dscp() to get the DSCP from the IPv4 header, then convert the
dscp_t value to __u8 with inet_dscp_to_dsfield().
Then, when we'll convert .flowi4_tos to dscp_t, we'll just have to drop
the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/462402a097260357a7aba80228612305f230b6a9.1729530028.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Tue, 22 Oct 2024 09:48:08 +0000 (11:48 +0200)]
ipv4: Prepare icmp_reply() to future .flowi4_tos conversion.
Use ip4h_dscp() to get the DSCP from the IPv4 header, then convert the
dscp_t value to __u8 with inet_dscp_to_dsfield().
Then, when we'll convert .flowi4_tos to dscp_t, we'll just have to drop
the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/61b7563563f8b0a562b5b62032fe5260034d0aac.1729530028.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Tue, 22 Oct 2024 09:48:00 +0000 (11:48 +0200)]
ipv4: Prepare fib_compute_spec_dst() to future .flowi4_tos conversion.
Use ip4h_dscp() to get the DSCP from the IPv4 header, then convert the
dscp_t value to __u8 with inet_dscp_to_dsfield().
Then, when we'll convert .flowi4_tos to dscp_t, we'll just have to drop
the inet_dscp_to_dsfield() call.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/a0eba69cce94f747e4c7516184a85ffd0abbe3f0.1729530028.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Tue, 29 Oct 2024 14:33:24 +0000 (15:33 +0100)]
Merge branch 'ibm-emac-more-cleanups'
Rosen Penev says:
====================
ibm: emac: more cleanups
Tested on Cisco MX60W.
v2: fixed build errors. Also added extra commits to clean the driver up
further.
v3: Added tested message. Removed bad alloc_netdev_dummy commit.
v4: removed modules changes from patchset. Added fix for if MAC not
found.
v5: added of_find_matching_node commit.
v6: resend after net-next merge.
v7: removed of_find_matching_node commit. Adjusted mutex_init patch.
v8: removed patch removing custom init/exit. Needs more work.
====================
Link: https://patch.msgid.link/20241022002245.843242-1-rosenp@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rosen Penev [Tue, 22 Oct 2024 00:22:45 +0000 (17:22 -0700)]
net: ibm: emac: generate random MAC if not found
On this Cisco MX60W, u-boot sets the local-mac-address property.
Unfortunately by default, the MAC is wrong and is actually located on a
UBI partition. Which means nvmem needs to be used to grab it.
In the case where that fails, EMAC fails to initialize instead of
generating a random MAC as many other drivers do.
Match behavior with other drivers to have a working ethernet interface.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rosen Penev [Tue, 22 Oct 2024 00:22:44 +0000 (17:22 -0700)]
net: ibm: emac: use devm for mutex_init
It seems since inception that mutex_destroy was never called for these
in _remove. Instead of handling this manually, just use devm for
simplicity.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rosen Penev [Tue, 22 Oct 2024 00:22:43 +0000 (17:22 -0700)]
net: ibm: emac: use platform_get_irq
No need for irq_of_parse_and_map since we have platform_device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rosen Penev [Tue, 22 Oct 2024 00:22:42 +0000 (17:22 -0700)]
net: ibm: emac: use devm_platform_ioremap_resource
No need to have a struct resource. Gets rid of the TODO.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rosen Penev [Tue, 22 Oct 2024 00:22:41 +0000 (17:22 -0700)]
net: ibm: emac: use netif_receive_skb_list
Small rx improvement. Would use napi_gro_receive instead but that's a
lot more involved than netif_receive_skb_list because of how the
function is implemented.
Before:
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 51556 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.04 sec 559 MBytes 467 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 48228 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.03 sec 558 MBytes 467 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 47600 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.04 sec 557 MBytes 466 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 37252 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.05 sec 559 MBytes 467 Mbits/sec
After:
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 40786 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.05 sec 572 MBytes 478 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 52482 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.04 sec 571 MBytes 477 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 48370 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.04 sec 572 MBytes 478 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 46086 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.05 sec 571 MBytes 476 Mbits/sec
> iperf -c 192.168.1.1
------------------------------------------------------------
Client connecting to 192.168.1.1, TCP port 5001
TCP window size: 16.0 KByte (default)
------------------------------------------------------------
[ 1] local 192.168.1.101 port 46062 connected with 192.168.1.1 port 5001
[ ID] Interval Transfer Bandwidth
[ 1] 0.00-10.04 sec 572 MBytes 478 Mbits/sec
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Tue, 29 Oct 2024 10:55:28 +0000 (11:55 +0100)]
Merge branch 'ipv4-convert-rtm_-new-del-addr-and-more-to-per-netns-rtnl'
Kuniyuki Iwashima says:
====================
ipv4: Convert RTM_{NEW,DEL}ADDR and more to per-netns RTNL.
The IPv4 address hash table and GC are already namespacified.
This series converts RTM_NEWADDR/RTM_DELADDR and some more
RTNL users to per-netns RTNL.
Changes:
v2:
* Add patch 1 to address sparse warning for CONFIG_DEBUG_NET_SMALL_RTNL=n
* Add Eric's tags to patch 2-12
v1: https://lore.kernel.org/netdev/
20241018012225.90409-1-kuniyu@amazon.com/
====================
Link: https://patch.msgid.link/20241021183239.79741-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:39 +0000 (11:32 -0700)]
ipv4: Convert devinet_ioctl to per-netns RTNL.
ioctl(SIOCGIFCONF) calls dev_ifconf() that operates on the current netns.
Let's use per-netns RTNL helpers in dev_ifconf() and inet_gifconf().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:38 +0000 (11:32 -0700)]
ipv4: Convert devinet_ioctl() to per-netns RTNL except for SIOCSIFFLAGS.
Basically, devinet_ioctl() operates on a single netns.
However, ioctl(SIOCSIFFLAGS) will trigger the netdev notifier
that could touch another netdev in different netns.
Let's use per-netns RTNL helper in devinet_ioctl() and place
ASSERT_RTNL() for SIOCSIFFLAGS.
We will remove ASSERT_RTNL() once RTM_SETLINK and RTM_DELLINK
are converted.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:37 +0000 (11:32 -0700)]
ipv4: Convert devinet_sysctl_forward() to per-netns RTNL.
devinet_sysctl_forward() touches only a single netns.
Let's use rtnl_trylock() and __in_dev_get_rtnl_net().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:36 +0000 (11:32 -0700)]
rtnetlink: Define rtnl_net_trylock().
We will need the per-netns version of rtnl_trylock().
rtnl_net_trylock() calls __rtnl_net_lock() only when rtnl_trylock()
successfully holds RTNL.
When RTNL is removed, we will use mutex_trylock() for per-netns RTNL.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:35 +0000 (11:32 -0700)]
ipv4: Convert check_lifetime() to per-netns RTNL.
Since commit
1675f385213e ("ipv4: Namespacify IPv4 address GC."),
check_lifetime() works on a per-netns basis.
Let's use rtnl_net_lock() and rtnl_net_dereference().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:34 +0000 (11:32 -0700)]
ipv4: Convert RTM_DELADDR to per-netns RTNL.
Let's push down RTNL into inet_rtm_deladdr() as rtnl_net_lock().
Now, ip_mc_autojoin_config() is always called under per-netns RTNL,
so ASSERT_RTNL() can be replaced with ASSERT_RTNL_NET().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:33 +0000 (11:32 -0700)]
ipv4: Use per-netns RTNL helpers in inet_rtm_newaddr().
inet_rtm_to_ifa() and find_matching_ifa() are called
under rtnl_net_lock().
__in_dev_get_rtnl() and in_dev_for_each_ifa_rtnl() there
can use per-netns RTNL helpers.
Let's define and use __in_dev_get_rtnl_net() and
in_dev_for_each_ifa_rtnl_net().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:32 +0000 (11:32 -0700)]
ipv4: Convert RTM_NEWADDR to per-netns RTNL.
The address hash table and GC are already namespacified.
Let's push down RTNL into inet_rtm_newaddr() as rtnl_net_lock().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:31 +0000 (11:32 -0700)]
ipv4: Don't allocate ifa for 0.0.0.0 in inet_rtm_newaddr().
When we pass 0.0.0.0 to __inet_insert_ifa(), it frees ifa and returns 0.
We can do this check much earlier for RTM_NEWADDR even before allocating
struct in_ifaddr.
Let's move the validation to
1. inet_insert_ifa() for ioctl()
2. inet_rtm_newaddr() for RTM_NEWADDR
Now, we can remove the same check in find_matching_ifa().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:30 +0000 (11:32 -0700)]
ipv4: Factorise RTM_NEWADDR validation to inet_validate_rtm().
rtm_to_ifaddr() validates some attributes, looks up a netdev,
allocates struct in_ifaddr, and validates IFA_CACHEINFO.
There is no reason to delay IFA_CACHEINFO validation.
We will push RTNL down to inet_rtm_newaddr(), and then we want
to complete rtnetlink validation before rtnl_net_lock().
Let's factorise the validation parts.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:29 +0000 (11:32 -0700)]
rtnetlink: Define RTNL_FLAG_DOIT_PERNET for per-netns RTNL doit().
We will push RTNL down to each doit() as rtnl_net_lock().
We can use RTNL_FLAG_DOIT_UNLOCKED to call doit() without RTNL, but doit()
will still hold RTNL.
Let's define RTNL_FLAG_DOIT_PERNET as an alias of RTNL_FLAG_DOIT_UNLOCKED.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Kuniyuki Iwashima [Mon, 21 Oct 2024 18:32:28 +0000 (11:32 -0700)]
rtnetlink: Make per-netns RTNL dereference helpers to macro.
When CONFIG_DEBUG_NET_SMALL_RTNL is off, rtnl_net_dereference() is the
static inline wrapper of rtnl_dereference() returning a plain (void *)
pointer to make sure net is always evaluated as requested in [0].
But, it makes sparse complain [1] when the pointer has __rcu annotation:
net/ipv4/devinet.c:674:47: sparse: warning: incorrect type in argument 2 (different address spaces)
net/ipv4/devinet.c:674:47: sparse: expected void *p
net/ipv4/devinet.c:674:47: sparse: got struct in_ifaddr [noderef] __rcu *
Also, if we evaluate net as (void *) in a macro, then the compiler
in turn fails to build due to -Werror=unused-value.
#define rtnl_net_dereference(net, p) \
({ \
(void *)net; \
rtnl_dereference(p); \
})
net/ipv4/devinet.c: In function ‘inet_rtm_deladdr’:
./include/linux/rtnetlink.h:154:17: error: statement with no effect [-Werror=unused-value]
154 | (void *)net; \
net/ipv4/devinet.c:674:21: note: in expansion of macro ‘rtnl_net_dereference’
674 | (ifa = rtnl_net_dereference(net, *ifap)) != NULL;
| ^~~~~~~~~~~~~~~~~~~~
Let's go back to the original simplest macro.
Note that checkpatch complains about this approach, but it's one-shot and
less noisy than the other two.
WARNING: Argument 'net' is not used in function-like macro
#76: FILE: include/linux/rtnetlink.h:142:
+#define rtnl_net_dereference(net, p) \
+ rtnl_dereference(p)
Fixes:
844e5e7e656d ("rtnetlink: Add assertion helpers for per-netns RTNL.")
Link: https://lore.kernel.org/netdev/20241004132145.7fd208e9@kernel.org/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/
202410200325.SaEJmyZS-lkp@intel.com/ [1]
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Dumazet [Tue, 22 Oct 2024 15:00:59 +0000 (15:00 +0000)]
neighbour: use kvzalloc()/kvfree()
mm layer is providing convenient functions, we do not have
to work around old limitations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gilad Naaman <gnaaman@drivenets.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20241022150059.1345406-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kory Maincent [Tue, 22 Oct 2024 15:14:18 +0000 (17:14 +0200)]
netlink: specs: Add missing phy-ntf command to ethtool spec
ETHTOOL_MSG_PHY_NTF description is missing in the ethtool netlink spec.
Add it to the spec.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20241022151418.875424-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Tue, 22 Oct 2024 13:48:19 +0000 (13:48 +0000)]
vsock: do not leave dangling sk pointer in vsock_create()
syzbot was able to trigger the following warning after recent
core network cleanup.
On error vsock_create() frees the allocated sk object, but sock_init_data()
has already attached it to the provided sock object.
We must clear sock->sk to avoid possible use-after-free later.
WARNING: CPU: 0 PID: 5282 at net/socket.c:1581 __sock_create+0x897/0x950 net/socket.c:1581
Modules linked in:
CPU: 0 UID: 0 PID: 5282 Comm: syz.2.43 Not tainted
6.12.0-rc2-syzkaller-00667-g53bac8330865 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024
RIP: 0010:__sock_create+0x897/0x950 net/socket.c:1581
Code: 7f 06 01 65 48 8b 34 25 00 d8 03 00 48 81 c6 b0 08 00 00 48 c7 c7 60 0b 0d 8d e8 d4 9a 3c 02 e9 11 f8 ff ff e8 0a ab 0d f8 90 <0f> 0b 90 e9 82 fd ff ff 89 e9 80 e1 07 fe c1 38 c1 0f 8c c7 f8 ff
RSP: 0018:
ffffc9000394fda8 EFLAGS:
00010293
RAX:
ffffffff89873c46 RBX:
ffff888079f3c818 RCX:
ffff8880314b9e00
RDX:
0000000000000000 RSI:
00000000ffffffed RDI:
0000000000000000
RBP:
ffffffff8d3337f0 R08:
ffffffff8987384e R09:
ffffffff8989473a
R10:
dffffc0000000000 R11:
fffffbfff203a276 R12:
00000000ffffffed
R13:
ffff888079f3c8c0 R14:
ffffffff898736e7 R15:
dffffc0000000000
FS:
00005555680ab500(0000) GS:
ffff8880b8600000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f22b11196d0 CR3:
00000000308c0000 CR4:
00000000003526f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
sock_create net/socket.c:1632 [inline]
__sys_socket_create net/socket.c:1669 [inline]
__sys_socket+0x150/0x3c0 net/socket.c:1716
__do_sys_socket net/socket.c:1730 [inline]
__se_sys_socket net/socket.c:1728 [inline]
__x64_sys_socket+0x7a/0x90 net/socket.c:1728
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f22b117dff9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007fff56aec0e8 EFLAGS:
00000246 ORIG_RAX:
0000000000000029
RAX:
ffffffffffffffda RBX:
00007f22b1335f80 RCX:
00007f22b117dff9
RDX:
0000000000000000 RSI:
0000000000000002 RDI:
0000000000000028
RBP:
00007f22b11f0296 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00007f22b1335f80 R14:
00007f22b1335f80 R15:
00000000000012dd
Fixes:
48156296a08c ("net: warn, if pf->create does not clear sock->sk on error")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20241022134819.1085254-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Ott [Wed, 23 Oct 2024 13:41:46 +0000 (15:41 +0200)]
net/mlx5: unique names for per device caches
Add the device name to the per device kmem_cache names to
ensure their uniqueness. This fixes warnings like this:
"kmem_cache of name 'mlx5_fs_fgs' already exists".
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20241023134146.28448-1-sebott@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Oct 2024 23:09:43 +0000 (16:09 -0700)]
Merge branch 'bonding-returns-detailed-error-about-xdp-failures'
Hangbin Liu says:
====================
Bonding: returns detailed error about XDP failures
Based on discussion[1], this patch set returns detailed error about XDP
failures. And update bonding document about XDP supports.
https://lore.kernel.org/
8088f2a7-3ab1-4a1e-996d-
c15703da13cc@blackwall.org
====================
Link: https://patch.msgid.link/20241021031211.814-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hangbin Liu [Mon, 21 Oct 2024 03:12:11 +0000 (03:12 +0000)]
Documentation: bonding: add XDP support explanation
Add document about which modes have native XDP support.
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20241021031211.814-3-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hangbin Liu [Mon, 21 Oct 2024 03:12:10 +0000 (03:12 +0000)]
bonding: return detailed error when loading native XDP fails
Bonding only supports native XDP for specific modes, which can lead to
confusion for users regarding why XDP loads successfully at times and
fails at others. This patch enhances error handling by returning detailed
error messages, providing users with clearer insights into the specific
reasons for the failure when loading native XDP.
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20241021031211.814-2-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Oct 2024 22:55:48 +0000 (15:55 -0700)]
Merge branch 'mptcp-various-small-improvements'
Matthieu Baerts says:
====================
mptcp: various small improvements
The following patches are not related to each other.
- Patch 1: Avoid sending advertisements on stale subflows, reducing
risks on loosing them.
- Patch 2: Annotate data-races around subflow->fully_established, using
READ/WRITE_ONCE().
- Patch 3: A small clean-up on the PM side, avoiding a bit of duplicated
code.
- Patch 4: Use "Middlebox interference" MP_TCPRST code in reaction to a
packet received without MPTCP options in the middle of a connection.
====================
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-0-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Davide Caratti [Mon, 21 Oct 2024 15:14:06 +0000 (17:14 +0200)]
mptcp: use "middlebox interference" RST when no DSS
RFC8684 suggests use of "Middlebox interference (code 0x06)" in case of
fully established subflow that carries data at TCP level with no DSS
sub-option.
This is generally the case when mpext is NULL or mpext->use_map is 0:
use a dedicated value of 'mapping_status' and use it before closing the
socket in subflow_check_data_avail().
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/518
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-4-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Mon, 21 Oct 2024 15:14:05 +0000 (17:14 +0200)]
mptcp: implement mptcp_pm_connection_closed
The MPTCP path manager event handler mptcp_pm_connection_closed
interface has been added in the commit
1b1c7a0ef7f3 ("mptcp: Add path
manager interface") but it was an empty function from then on.
With such name, it sounds good to invoke mptcp_event with the
MPTCP_EVENT_CLOSED event type from it. It also removes a bit of
duplicated code.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-3-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gang Yan [Mon, 21 Oct 2024 15:14:04 +0000 (17:14 +0200)]
mptcp: annotate data-races around subflow->fully_established
We introduce the same handling for potential data races with the
'fully_established' flag in subflow as previously done for
msk->fully_established.
Additionally, we make a crucial change: convert the subflow's
'fully_established' from 'bit_field' to 'bool' type. This is
necessary because methods for avoiding data races don't work well
with 'bit_field'. Specifically, the 'READ_ONCE' needs to know
the size of the variable being accessed, which is not supported in
'bit_field'. Also, 'test_bit' expect the address of 'bit_field'.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/516
Signed-off-by: Gang Yan <yangang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-2-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts (NGI0) [Mon, 21 Oct 2024 15:14:03 +0000 (17:14 +0200)]
mptcp: pm: send ACK on non-stale subflows
If the subflow is considered as "staled", it is better to avoid it to
send an ACK carrying an ADD_ADDR or RM_ADDR. Another subflow, if any,
will then be selected.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20241021-net-next-mptcp-misc-6-13-v1-1-1ef02746504a@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 28 Oct 2024 22:54:42 +0000 (15:54 -0700)]
Merge branch 'net-systemport-minor-io-macros-changes'
Florian Fainelli says:
====================
net: systemport: Minor IO macros changes
This patch series addresses the warning initially reported by Vladimir
here:
https://lore.kernel.org/all/
20241014150139.927423-1-vladimir.oltean@nxp.com/
and follows on with proceeding with his suggestion the IO macros to the
header file.
====================
Link: https://patch.msgid.link/20241021174935.57658-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Mon, 21 Oct 2024 17:49:35 +0000 (10:49 -0700)]
net: systemport: Move IO macros to header file
Move the BCM_SYSPORT_IO_MACRO() definition and its use to bcmsysport.h
where it is more appropriate and where static inline helpers are
acceptable. While at it, make sure that the macro 'offset' argument does
not trigger a checkpatch warning due to possible argument re-use.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241021174935.57658-3-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Mon, 21 Oct 2024 17:49:34 +0000 (10:49 -0700)]
net: systemport: Remove unused txchk accessors
Vladimir reported the following warning with clang-16 and W=1:
warning: unused function 'txchk_readl' [-Wunused-function]
BCM_SYSPORT_IO_MACRO(txchk, SYS_PORT_TXCHK_OFFSET);
note: expanded from macro 'BCM_SYSPORT_IO_MACRO'
warning: unused function 'txchk_writel' [-Wunused-function]
note: expanded from macro 'BCM_SYSPORT_IO_MACRO'
warning: unused function 'tbuf_readl' [-Wunused-function]
BCM_SYSPORT_IO_MACRO(tbuf, SYS_PORT_TBUF_OFFSET);
note: expanded from macro 'BCM_SYSPORT_IO_MACRO'
warning: unused function 'tbuf_writel' [-Wunused-function]
note: expanded from macro 'BCM_SYSPORT_IO_MACRO'
The TXCHK and RBUF blocks are not being accessed, remove the IO macros
used to access those blocks. No functional impact.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241021174935.57658-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leo Stone [Mon, 21 Oct 2024 17:46:44 +0000 (10:46 -0700)]
selftest/tcp-ao: Add filter tests
Add tests that check if getsockopt(TCP_AO_GET_KEYS) returns the right
keys when using different filters.
Sample output:
> # ok 114 filter keys: by sndid, rcvid, address
> # ok 115 filter keys: by is_current
> # ok 116 filter keys: by is_rnext
> # ok 117 filter keys: by sndid, rcvid
> # ok 118 filter keys: correct nkeys when in.nkeys < matches
Acked-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Leo Stone <leocstone@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241021174652.6949-1-leocstone@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yazen Ghannam [Mon, 21 Oct 2024 15:38:25 +0000 (15:38 +0000)]
net: amd8111e: Remove duplicate definition of PCI_VENDOR_ID_AMD
The AMD PCI vendor ID is already defined in <linux/pci_ids.h>.
Remove this local definition as it is not needed.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/20241021153825.2536819-1-yazen.ghannam@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Danila Tikhonov [Sun, 20 Oct 2024 20:56:09 +0000 (23:56 +0300)]
dt-bindings: nfc: nxp,nci: Document PN553 compatible
The PN553 is another NFC chip from NXP, document the compatible in the
bindings.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20241020205615.211256-2-danila@jiaxyga.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 16 Oct 2024 01:11:44 +0000 (18:11 -0700)]
configs/debug: make sure PROVE_RCU_LIST=y takes effect
Commit
0aaa8977acbf ("configs: introduce debug.config for CI-like setup")
added CONFIG_PROVE_RCU_LIST=y to the common CI config,
but RCU_EXPERT is not set, and it's a dependency for
CONFIG_PROVE_RCU_LIST=y. Make sure CIs take advantage
of CONFIG_PROVE_RCU_LIST=y, recent fixes in networking
indicate that it does catch bugs.
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241016011144.3058445-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Javier Carrasco [Sat, 19 Oct 2024 20:16:49 +0000 (22:16 +0200)]
net: dsa: mv88e6xxx: fix unreleased fwnode_handle in setup_port()
'ports_fwnode' is initialized via device_get_named_child_node(), which
requires a call to fwnode_handle_put() when the variable is no longer
required to avoid leaking memory.
Add the missing fwnode_handle_put() after 'ports_fwnode' has been used
and is no longer required.
Fixes:
94a2a84f5e9e ("net: dsa: mv88e6xxx: Support LED control")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 18 Oct 2024 13:35:28 +0000 (15:35 +0200)]
bareudp: Use pcpu stats to update rx_dropped counter.
Use the core_stats rx_dropped counter to avoid the cost of atomic
increments.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raj Kumar Bhagat [Tue, 22 Oct 2024 07:24:06 +0000 (12:54 +0530)]
wifi: ath12k: convert tasklet to BH workqueue for CE interrupts
Currently in Ath12k, tasklet is used to handle the BH context of CE
interrupts. However the tasklet is marked deprecated and has some
design flaws. To replace tasklets, BH workqueue support has been
added. BH workqueue behaves similarly to regular workqueues except
that the queued work items are executed in the BH context.
Hence, convert the tasklet to BH workqueue for handling CE interrupts
in the BH context.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241022072406.3231450-1-quic_rajkbhag@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Paolo Abeni [Fri, 25 Oct 2024 07:08:22 +0000 (09:08 +0200)]
Merge git://git./linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR.
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
projects / linux-block.git / log