drm/i915: Init DRM connector polled field early

After an HPD IRQ storm on a connector intel_hpd_irq_storm_detect() will
set the connector's HPD pin state to HPD_MARK_DISABLED and the IRQ gets
disabled. Subsequently intel_hpd_irq_storm_switch_to_polling() will
enable polling for these connectors, setting the pin state to
HPD_DISABLED, but only if the connector's base.polled field is set to
DRM_CONNECTOR_POLL_HPD. intel_hpd_irq_storm_reenable_work() will
reenable the IRQ - after 2 minutes -  if the pin state is HPD_DISABLED.

The connectors will be created with their base.polled field set to 0,
which gets initialized only later in i915_hpd_poll_init_work() (using
intel_connector::polled). If a storm is detected on a connector after
it's created and IRQs are enabled on it - by intel_hpd_init() - and
before its bease.polled field is initialized in the above work, the
connector's HPD pin will stay in the HPD_MARK_DISABLED state - leaving
the IRQ disabled indefinitely - and polling will not get enabled on it as
intended.

I can't see a reason for initializing base.polled in a delayed manner,
so do this already when creating the connector, to prevent the above
race condition.

Link: https://patchwork.freedesktop.org/patch/msgid/20240104083008.2715733-2-imre.deak@intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>

drm/i915/display: Use helper to select C20 MPLLA/B

We used to select between MPLLA/B with the following

state->tx[0] & C20_PHY_USE_MPLLB

Since this is used a few places within C20 PLL setting,
let's introduce a helper function to clean up the code
a bit.

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240105112243.224199-1-mika.kahola@intel.com

drm/i915: Disable DSB in Xe KMD

Often getting DSB overflows when starting Xorg or Wayland compositors
when running Xe KMD.
Issue was reported but nothing was done, so disabling DSB as whole
until properly fixed in Xe KMD.

v2:
- move check to HAS_DSB(Jani)

v3:
- use IS_ENABLED(I915) check in intel_dsb_prepare()

Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/989
Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1031
Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/1072
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Francois Dugast <francois.dugast@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104162411.56085-1-jose.souza@intel.com

drm/i915/tv: use DISPLAY_VER instead of GRAPHICS_VER

Display code should not care about graphics version. It's only comments
here, but update anyway.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104174350.823605-5-jani.nikula@intel.com

drm/i915/display: use IS_DISPLAY_VER instead of IS_GRAPHICS_VER

Display code should not care about graphics version.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104174350.823605-4-jani.nikula@intel.com

drm/i915/hdcp: use DISPLAY_VER instead of GRAPHICS_VER

Display code should not care about graphics version. While at it,
abstract the version check to a separate macro.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104174350.823605-3-jani.nikula@intel.com

drm/i915/dmc: use DISPLAY_VER instead of GRAPHICS_VER

Display code should not care about graphics version.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104174350.823605-2-jani.nikula@intel.com

drm/i915/irq: use DISPLAY_VER instead of GRAPHICS_VER

Display code should not care about graphics version.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240104174350.823605-1-jani.nikula@intel.com

drm/i915/dp: Fix the PSR debugfs entries wrt. MST connectors

MST connectors don't have a static attached encoder, as their encoder
can change depending on the pipe they use; so the encoder for an MST
connector can't be retrieved using intel_dp_attached_encoder() (which
may return NULL for MST). Most of the PSR debugfs entries depend on a
static connector -> encoder mapping which is only true for eDP and SST
DP connectors and not for MST. These debugfs entries were enabled for
MST connectors as well recently to provide PR information for them, but
handling MST connectors needs more changes.

Fix this by not adding for now the PSR entries on MST connectors. To
make things more uniform add the entries for SST connectors on all
platforms, not just on platforms supporting DP2.0.

v2:
- Keep adding the entries for SST connectors. (Jouni)
- Add a TODO: comment for MST support.

Fixes: ef75c25e8fed ("drm/i915/panelreplay: Debugfs support for panel replay")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9850
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240103152609.2434100-1-imre.deak@intel.com

drm/i915/display: Skip C10 state verification in case of fastset

PLL's are not programmed in case of fastset so the state
verification compares bios programmed PLL values against
sw PLL values. To overcome this limitation, we can skip
the state verification for C10 in fastset case as the
driver is not writing PLL values.

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231219123246.832245-1-mika.kahola@intel.com

drm/i915/display: Cleanup mplla/mpllb selection

The function intel_c20_use_mplla() is not really
widely used and can be replaced with the more suitable

pll->tx[0] & C20_PHY_USE_MPLLB

expression. Let's remove the intel_c20_use_mplla()
alltogether and replace mplla/mpllb selection by
checking mpllb bit.

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240102115741.118525-4-mika.kahola@intel.com

drm/i915/display: Store hw clock for C20

We can calculate the hw port clock during the hw readout
and store it as pll_state->clock for C20 state verification.
In order to do that we need to move intel_c20pll_calc_port_clock()
function.

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240102115741.118525-3-mika.kahola@intel.com

drm/i915/display: Fix C20 pll selection for state verification

Add pll selection check for C20 as well as
clock state verification0. We have been relying
on sw state to select A or B pll's. This is incorrect
as the hw might see this selection differently. This
patch fixes this shortcoming by reading pll selection
for both sw and hw states and compares if these two
selections match.

Fixes: 59be90248b42 ("drm/i915/mtl: C20 state verification")

v2: reword commit message and include fix to a
    original commit (Imre)
    Compare pll selection (Jani)

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240102115741.118525-2-mika.kahola@intel.com

drm/i915/mtl: Add fake PCH for Meteor Lake

Correct the implementation trying to detect MTL PCH with
the MTL fake PCH id.

On MTL, both the North Display (NDE) and South Display (SDE) functionality
reside on the same die (the SoC die in this case), unlike many past
platforms where the SDE was on a separate PCH die. The code is (badly)
structured today in a way that assumes the SDE is always on the PCH for
modern platforms, so on platforms where we don't actually need to identify
the PCH to figure out how the SDE behaves (i.e., all DG1/2 GPUs as well as
MTL and LNL),we've been assigning a "fake PCH" as a quickhack that allows
us to avoid restructuring a bunch of the code.we've been assigning a
"fake PCH" as a quick hack that allows us to avoid restructuring a bunch
of the code.

Removed unused macros of LNL amd MTL as well.

v2: Reorder PCH_MTL conditional check (Matt Roper)
    Reverting to PCH_MTL for PICA interrupt(Matt Roper)

Signed-off-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231219185233.1469675-1-haridhar.kalvala@intel.com

drm/i915/bios: remove some unused leftover declarations

Remove some unused declarations probably left behind after some
refactoring.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231221105414.1518267-1-jani.nikula@intel.com

drm/i915/display: Take care of VSC select field in video dip ctl register

We need to configure VSC Select field in video dip ctl if we want to have
e.g. colorimetry date in our VSC SDP.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-8-jouni.hogander@intel.com

drm/i915/display: Read PSR configuration before VSC SDP

VSC SDP sending is taken care by PSR HW and it's not enabled in
VIDEO_DIP_CTL when PSR is enabled. Readback of VSC SDP is depending on
VSC_SDP being set in intel_crtc_state->infoframes.enabled. In case of PSR
setting this flag is taken care by PSR code -> read back PSR configuration
before reading VSC SDP otherwise we get pipeconfig mismatch error.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-7-jouni.hogander@intel.com

drm/i915/display: Ignore only psr specific part of vsc sdp

Pipe config check is currently ignoring vsc sdp changes completely
if psr is enabled. We want to ignore only PSR part of it as there
might be changes in colorimetry data. Also read back vsc_sdp when psr is
used.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-6-jouni.hogander@intel.com

drm/i915/display: Fix vsc_sdp computation

Currently colorimetry data is not added for psr1 or non-psr case.
Fix this by adding it as needed.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-5-jouni.hogander@intel.com

drm/i915/display: Unify VSC SPD preparation

There is no specific reason to prepare VSC SDP for PSR case somehow
differently. Unify PSR and non-PSR preparation.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-4-jouni.hogander@intel.com

drm/i915/display: Move colorimetry_support from intel_psr to intel_dp

Colorimetry support is not really a PSR specific thing. Move it to intel_dp
struct and use it also when preparing vsc sdp for non-PSR case.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-3-jouni.hogander@intel.com

drm/i915/display: Remove intel_crtc_state->psr_vsc

There is no really need to have separate vsc for psr usage. Use
intel_crtc_state->infoframes.vsc instead.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231220103609.1384523-2-jouni.hogander@intel.com

drm/i915/hdcp: Fail Repeater authentication if Type1 device not present

Fail repeater authentication step in case RX_INFO indicates
HDCP1.x or HDCP2.0/2.1 device is present downstream in repeater
topology and content type set by userspace is Type1.

--v2
-Fix build error.

--v3
-remove mst encoder check as branch device also act as repeater

Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231215050915.2070119-1-suraj.kandpal@intel.com

drm/i915/cdclk: Remove divider field from tables

The cdclk tables were introduced with commit 736da8112fee ("drm/i915:
Use literal representation of cdclk tables"). It has been almost 4 years
and the divider field was not really used yet. Let's remove it.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231124205522.57696-2-gustavo.sousa@intel.com

drm/i915/dp: Fix passing the correct DPCD_REV for drm_dp_set_phy_test_pattern

Using link_status to get DPCD_REV fails when disabling/defaulting
phy pattern. Use intel_dp->dpcd to access DPCD_REV correctly.

Fixes: 8cdf72711928 ("drm/i915/dp: Program vswing, pre-emphasis, test-pattern")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213211542.3585105-3-khaled.almahallawy@intel.com

drm/i915/dp: Add TPS4 PHY test pattern support

Adding support for TPS4 (CP2520 Pattern 3) PHY pattern source tests.

v2: rebase
v3:
  - Enable TPS4 only for supported platforms (Jani)
  - Uppercase in macro names (Jani)
  - Fix indentation (Jani)
  - Use drm_warn instead of WARN
v4: Disable TPS4 pattern on supported platforms only

Bspec: 50482, 50484, 7557
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213211542.3585105-2-khaled.almahallawy@intel.com

drm/i915/dp: Use LINK_QUAL_PATTERN_* Phy test pattern names

Starting from DP2.0 specs, DPCD 248h is renamed
LINK_QUAL_PATTERN_SELECT and it has the same values of registers
DPCD 10Bh-10Eh.
Use the PHY pattern names defined for DPCD 10Bh-10Eh in order to add
CP2520 Pattern 3 (TPS4) phy pattern support in the next
patch of this series and DP2.1 PHY patterns for future series.

v2: rebase

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213211542.3585105-1-khaled.almahallawy@intel.com

drm/i915: Ratelimit debug log in vm_fault_ttm

Test like i915_gem_mman_live_selftests/igt_mmap_migrate can cause
dmesg spamming. Use ratelimit api to reduce log rate.

References: https://gitlab.freedesktop.org/drm/intel/-/issues/7038
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231206210948.106238-3-andi.shyti@linux.intel.com

drm/print: Add drm_dbg_ratelimited

Add a function for ratelimitted debug print.

Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231206210948.106238-2-andi.shyti@linux.intel.com

drm/i915/hdcp: fix intel_hdcp_get_repeater_ctl() error return value

intel_hdcp_get_repeater_ctl() is supposed to return unsigned register
contents. Returning negative error values is unexpected, and none of the
callers check for that.

Sort of fix the error cases by returning 0. I don't think we should hit
these cases anyway, and using 0 for the registers is safer than
0xffffffea (-EINVAL).

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231219104746.1065431-2-jani.nikula@intel.com

drm/i915/hdcp: unify connector logging format

It's customary to debug log connectors using [CONNECTOR:%d:%s]
format. Make the HDCP code follow suit.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231219104746.1065431-1-jani.nikula@intel.com

drm/i915/display: Remove dead code around intel_atomic_helper->free_list

After switching to directly using dma_fence instead of i915_sw_fence we
have left some dead code around intel_atomic_helper->free_list. Remove that
dead code.

v2: Remove intel_atomic_state->freed as well

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114134141.2527694-1-jouni.hogander@intel.com

drm/i915/dmc: Print out the DMC mmio register list at fw load time

To help with debugging print out the mmio list contained in the DMC
firmware. Also highlight the event registers, and whether we're going
to disable them or not.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211213750.27109-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/dmc: Also disable HRR event on TGL/ADLS main DMC

Unlike later platforms TGL/ADLS has the half refresh rate (HRR) event
on the main DMC (as opposed to the pipe DMC). Since we're disabling
that event on all later platforms already let's do the same on
TGL/ADLS as well.

There is supposedly a bit somewhere (DMC_CHICKEN on TGL) to make
the handler not do anything, but we don't currently have code
to frob it. Though that bit should be off by default, the ADL+
experience has shown us that trusting any of this isn't a good
idea. So seems safer to just disable all event handlers we know
that we don't need.

Also the TGL/ADLS DMC firmware is apparently using the wrong event
(undelayed vblank) here anyway. It should be using the delayed
vblank event instead (like ADL+ firmware does), but they didn't
release a firmware fix for this and instead just hacked around
this in the Windows driver code :/

v2: Also disable the event on ADLS (Imre)

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213150807.21331-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/dmc: Also disable the flip queue event on TGL main DMC

Unlike later platforms TGL has its flip queue event (CLK_MSEC) on
the main DMC (as opposed to the pipe DMC). Currently we're doing
a second pass to disable that, but let's just follow the same
approach as the later platforms and never even enable the event
in the first place.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211213750.27109-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/dmc: Don't enable any pipe DMC events

The pipe DMC seems to be making a mess of things in ADL. Various weird
symptoms have been observed such as missing vblank irqs, typicalle
happening when using multiple displays.

Keep all pipe DMC event handlers disabled until needed (which is never
atm). This is also what Windows does on ADL+.

We can also drop DG2 from disable_all_flip_queue_events() since
on DG2 the pipe DMC is the one that handles the flip queue events.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8685
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211213750.27109-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/mtl: Fix HDMI/DP PLL clock selection

Select the HDMI specific PLL clock only for HDMI outputs.

Fixes: 62618c7f117e ("drm/i915/mtl: C20 PLL programming")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213220526.1828827-1-imre.deak@intel.com

drm/i915: Simplify intel_ddi_compute_min_voltage_level()

Drop the redundant dev_priv parameters from
intel_ddi_compute_min_voltage_level() to make life easier.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128115138.13238-9-ville.syrjala@linux.intel.com
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>

drm/i915/mtl: Calculate the correct voltage level from port_clock

On MTL we need to bump the voltage level to only 1 (not 2)
when port clock exceeds 594MHz. Make it so.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128115138.13238-8-ville.syrjala@linux.intel.com
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>

drm/i915: Split intel_ddi_compute_min_voltage_level() into platform variants

The mess inside intel_ddi_compute_min_voltage_level() is illegible.
Clean it up a bit by splitting the internals into per-platform
functions.

TODO: make it a vfunc?

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128115138.13238-7-ville.syrjala@linux.intel.com
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>

drm/i915/mtl: Fix voltage_level for cdclk==480MHz

Allow MTL to use voltage level 1 for 480MHz cdclk,
instead of the voltage level 2 that it's currently using.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128115138.13238-6-ville.syrjala@linux.intel.com
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>

drm/i915/cdclk: Rewrite cdclk->voltage_level selection to use tables

The cdclk->voltage_level if ladders are hard to read, especially as
they're written the other way around compared to how bspec lists
the limits. Let's rewrite them to use simple arrays that gives us
the max cdclk for each voltage level.

v2: Bump the jsl/ehl max cdclk in the table to 652.8 MHz to
    accommodate JSL machines in CI that boot with high cdclk

Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211221759.29725-1-ville.syrjala@linux.intel.com

drm/i915/cdclk: Remove the assumption that cdclk divider==2 when using squashing

Currently we have a hardcoded assumption that the cdclk divider
(2*cd2x divider) is always 2 when squashing is used. While that
is true for all current platforms it might not hold in the future.
So eliminate the assumption and calculate the correct divider
from the other parameters.

v2: s/cd2x divider/cdclk divider/ (Gustavo)
    s/clock/unsquashed_cdclk/ (Gustavo)

Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211221636.29658-1-ville.syrjala@linux.intel.com

drm/i915/cdclk: Give the squash waveform length a name

Replace the slightly magic 'size = 16' with a bit more descriptive
name. We'll have another user for this value later on.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128115138.13238-3-ville.syrjala@linux.intel.com
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>

drm/i915/cdclk: s/-1/~0/ when dealing with unsigned values

cdclk_pll_is_unknown() used ~0 when checking for the "VCO is
unknown" value, but the assignment uses -1. They are the same
in the end, but let's use the same ~0 form on both sides for
consistency.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128115138.13238-2-ville.syrjala@linux.intel.com
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>

drm/i915: Reject async flips with bigjoiner

Currently async flips are busted when bigjoiner is in use.
As a short term fix simply reject async flips in that case.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9769
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211081134.2698-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

drm/i915/display: Wait for PHY readiness not needed for disabling sequence

When going through the disconnection flow we don't need to wait for PHY
readiness and hence we can skip the wait part. For disabling the function
returns false as an indicator that the power is not enabled. After all,
we are not even using the return value when Type-C is disconnecting.

v2: Cleanup for increased readibility (Imre)

BSpec: 65380

For VLK-53734

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231212115130.485911-1-mika.kahola@intel.com

drm/i915/display: Get bigjoiner config before dsc config during readout

Currently we get bigjoiner config after the dsc get config, during HW
readout.
Since dsc_get_config now uses bigjoiner flags/pipes to compute DSC PPS
parameter pic_width, this results in a state mismatch when Bigjoiner
and DSC are used together.

So call get bigjoiner config before calling dsc get config function.

Fixes: 8b70b5691704 ("drm/i915/vdsc: Fill the intel_dsc_get_pps_config function")
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231122064627.905828-1-ankit.k.nautiyal@intel.com

drm/i915/display: do not use cursor size reduction on MTL

Cursor size reduction is not supported since MTL.

Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231124-cur_size_reduction-v1-1-30495dba475f@intel.com

drm/i915/edp: don't write to DP_LINK_BW_SET when using rate select

The eDP 1.5 spec adds a clarification for eDP 1.4x:

> For eDP v1.4x, if the Source device chooses the Main-Link rate by way
> of DPCD 00100h, the Sink device shall ignore DPCD 00115h[2:0].

We write 0 to DP_LINK_BW_SET (DPCD 100h) even when using
DP_LINK_RATE_SET (DPCD 114h). Stop doing that, as it can cause the panel
to ignore the rate set method.

Moreover, 0 is a reserved value for DP_LINK_BW_SET, and should not be
used.

v2: Improve the comments (Ville)

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9081
Tested-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231205180551.2476228-1-jani.nikula@intel.com

drm/i915: Drop irqsave/restore for flip_done_handler()

Since flip_done_handler() is always called from the irq handler
we can skip the irqsave/restore dance.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230928152450.30109-2-ville.syrjala@linux.intel.com
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>

drm/i915: Stop accessing crtc->state from the flip done irq

Assuming crtc->state is pointing at the correct thing for the
async flip commit is nonsense. If we had already queued up multiple
commits this would point at the very lates crtc state even if the
older commits hadn't even happened yet.

Instead properly stage/arm the event like we do for async flips.
Since we don't need to arm multiple of these at the same time we
don't need a list like the normal vblank even processing uses.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230928152450.30109-1-ville.syrjala@linux.intel.com
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>

drm/i915/mtl: Rename the link_bit_rate to clock in C20 pll_state

With the cleanup of the misleading clock value to avoid extra
calculations to convert between link_bit_rate and clock, use
one standard "clock" field for the c20 pll which works with
crtc_state->port_clock field.

Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207221025.2032207-4-radhakrishna.sripada@intel.com

drm/i915/mtl: Remove misleading "clock" field from C20 pll_state

The field link_bit_rate serves as the actual clock value for the C20
pll_state structure. Remove the misleading clock field. The subsequent
patch would rename the link_bit_rate as the clock field.

Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207221025.2032207-3-radhakrishna.sripada@intel.com

drm/i915/mtl: Use port clock compatible numbers for C20 phy

In C20 pll_state link_bit_rate and clock fields are bit redundant. Since
many of the helpers assume the clock values, which are different from
link_bit_rate for dp2.0, convert the helpers to use the numbers that
are compatible with link_bit_rate.

Currently link_bit_rate is compatible with crtc_state->port_clock. The
function intel_c20pll_calc_port_clock returns the number which is
compatible with crtc_state->port_clock. In order to avoid extra
conversions b/ween clock and link_bit_rate, remove "clock" field from the
C20 pll_state and then rename "link_bit_rate" as "clock".

While at it rely on crtc_state->port_clock during C20 Pll programming.

Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207221025.2032207-2-radhakrishna.sripada@intel.com

drm/i915/tv: Drop redundant null checks

Neither 'tv_mode' or 'color_conversion' can be NULL,
so drop the pointless checks.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/cstate/crtc_state/ in intel_get_frame_time_us()

Use standard variable name 'crtc_state' instead of 'cstate'.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Drop redunant null check from intel_get_frame_time_us()

intel_get_frame_time_us() is never called with a NULL crtc_state so
drop the redundant check.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Drop NULL fb check from intel_fb_uses_dpt()

intel_fb_uses_dpt() should not be called with a NULL fb, so
drop the check.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Drop crtc NULL check from intel_crtc_active()

intel_crtc_active() is never called with a NULL crtc. Drop
the redundant NULL check.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Drop redundant NULL check

intel_bios_get_dsc_params() is only called from
gen11_dsi_dsc_compute_config() and it always passes a non-NULL
crtc_state in. Drop the redundant check.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Streamline intel_dsc_pps_read()

intel_dsc_pps_read() is rather convoluted. Make it legible.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix intel_atomic_setup_scalers() plane_state handling

Since the plane_state variable is declared outside the scaler_users
loop in intel_atomic_setup_scalers(), and it's never reset back to
NULL inside the loop we may end up calling intel_atomic_setup_scaler()
with a non-NULL plane state for the pipe scaling case. That is bad
because intel_atomic_setup_scaler() determines whether we are doing
plane scaling or pipe scaling based on plane_state!=NULL. The end
result is that we may miscalculate the scaler mode for pipe scaling.

The hardware becomes somewhat upset if we end up in this situation
when scanning out a planar format on a SDR plane. We end up
programming the pipe scaler into planar mode as well, and the
result is a screenfull of garbage.

Fix the situation by making sure we pass the correct plane_state==NULL
when calculating the scaler mode for pipe scaling.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207193441.20206-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fix remapped stride with CCS on ADL+

On ADL+ the hardware automagically calculates the CCS AUX surface
stride from the main surface stride, so when remapping we can't
really play a lot of tricks with the main surface stride, or else
the AUX surface stride would get miscalculated and no longer
match the actual data layout in memory.

Supposedly we could remap in 256 main surface tile units
(AUX page(4096)/cachline(64)*4(4x1 main surface tiles per
AUX cacheline)=256 main surface tiles), but the extra complexity
is probably not worth the hassle.

So let's just make sure our mapping stride is calculated from
the full framebuffer stride (instead of the framebuffer width).
This way the stride we program into PLANE_STRIDE will be the
original framebuffer stride, and thus there will be no change
to the AUX stride/layout.

Cc: stable@vger.kernel.org
Cc: Imre Deak <imre.deak@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231205180308.7505-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>

drm/i915/display: Add intel_fb_bo_framebuffer_fini

Xe needs intel_fb_bo_framebuffer_fini for taking care of unpinning the fb
and taking reference.  In i915 this can be empty.

Also move intel_frontbuffer_get to be done after
intel_fb_bo_framebuffer_init to have reasonable sequences:

intel_fb_bo_framebuffer_init
intel_frontbuffer_get
...
intel_frontbuffer_put
intel_fb_bo_framebuffer_fini

v2: Empty function instead of define

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231207083451.2184562-1-jouni.hogander@intel.com

drm/i915/display: Use i915_gem_object_get_dma_address to get dma address

Works better for xe like that. obj is no longer const.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204134946.16219-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915: use octal permissions in display debugfs

Octal permissions are preferred over the symbolics ones.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231205134143.2427661-3-jani.nikula@intel.com

drm/i915: pass struct intel_connector to connector debugfs fops

Prefer struct intel_connector over struct drm_connector, and unify the
declarations in the fops.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231205134143.2427661-2-jani.nikula@intel.com

drm/i915: use intel_connector in intel_connector_debugfs_add()

Prefer struct intel_connector over struct drm_connector.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231205134143.2427661-1-jani.nikula@intel.com

drm/i915/rpm: add rpm_to_i915() helper around container_of()

Reduce the duplication.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231205121545.2338665-1-jani.nikula@intel.com

drm/i915: handle uncore spinlock when not available

The uncore code may not always be available (e.g. when we build the
display code with Xe), so we can't always rely on having the uncore's
spinlock.

To handle this, split the spin_lock/unlock_irqsave/restore() into
spin_lock/unlock() followed by a call to local_irq_save/restore() and
create wrapper functions for locking and unlocking the uncore's
spinlock.  In these functions, we have a condition check and only
actually try to lock/unlock the spinlock when I915 is defined, and
thus uncore is available.

This keeps the ifdefs contained in these new functions and all such
logic inside the display code.

Cc: Tvrtko Ursulin <tvrto.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231201100032.1367589-1-luciano.coelho@intel.com

drm/i915: Fix ADL+ tiled plane stride when the POT stride is smaller than the original

plane_view_scanout_stride() currently assumes that we had to pad the
mapping stride with dummy pages in order to align it. But that is not
the case if the original fb stride exceeds the aligned stride used
to populate the remapped view, which is calculated from the user
specified framebuffer width rather than the user specified framebuffer
stride.

Ignore the original fb stride in this case and just stick to the POT
aligned stride. Getting this wrong will cause the plane to fetch the
wrong data, and can lead to fault errors if the page tables at the
bogus location aren't even populated.

TODO: figure out if this is OK for CCS, or if we should instead increase
the width of the view to cover the entire user specified fb stride
instead...

Cc: Imre Deak <imre.deak@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204202443.31247-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>

drm/i915/dsi: Use devm_gpiod_get() for all GPIOs

soc_gpio_set_value() already uses devm_gpiod_get(), lets be consistent
and use devm_gpiod_get() for all GPIOs.

This allows removing the intel_dsi_vbt_gpio_cleanup() function,
which only function was to put the GPIO-descriptors.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231201161130.23976-1-hdegoede@redhat.com

drm/i915/display: Don't use "proxy" headers

The driver uses math.h and not util_macros.h.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231129140129.699767-1-andriy.shevchenko@linux.intel.com

drm/i915/syncmap: squelch a sparse warning

The code is fine, really, but tweak it to get rid of the sparse warning:

drivers/gpu/drm/i915/selftests/i915_syncmap.c:80:54: warning: dubious: x | !y

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231129173506.1194437-1-jani.nikula@intel.com

drm/i915/display: Split i915 specific code away from intel_fb.c

We are preparing for Xe driver. Backing object implementation is differing
between i915 and Xe. Split i915 specific code into separate source file
built only for i915.

v9:
  - Use ERR_CAST
v8:
  - return original error code from intel_fb_bo_lookup_valid_bo on failure
v7:
  - drop #include <drm/drm_plane.h>
  - s/user_mode_cmd/mode_cmd/
  - Use passed i915 pointer instead of to_i915(obj->base.dev)
v6: Add missing intel_fb_bo.[ch]
v5:
  - Keep drm_any_plane_has_format check in intel_fb.c
  - Use mode_cmd instead of user_mode_cmd for intel_fb_bo_lookup_valid_bo
v4: Move drm_any_plane_has_format check into intel_fb_bo.c
v3: Fix failure handling in intel_framebuffer_init
v2: Couple of fixes to error value handling

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114840.841311-5-jouni.hogander@intel.com

drm/i915/display: Handle invalid fb_modifier in intel_fb_modifier_to_tiling

Lookup_modifier is returning INTEL_PLANE_CAP_TILING_4 on invalid
fb_modifier value. Use lookup_modifier_or_null in
intel_fb_modifier_to_tiling and return I915_TILING_NONE in case
lookup_modifier_or_null returns null.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114840.841311-4-jouni.hogander@intel.com

drm/i915/display: Convert intel_fb_modifier_to_tiling as non-static

We are about to split i915 specific code from intel_fb.c. Convert
intel_fb_modifier_to_tiling as non-static to allow calling it from split
code.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114840.841311-3-jouni.hogander@intel.com

drm/i915/display: use intel_bo_to_drm_bo in intel_fb.c

We are preparing for Xe driver. I915 and Xe object implementation are
differing. Do not use  i915_gem_object->base directly. Instead use
intel_bo_to_drm_bo.

Also use drm_gem_object_put instead of i915_gem_object_put. This should be
ok as i915_gem_object_put is really just doing  __drm_gem_object_put.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114840.841311-2-jouni.hogander@intel.com

drm/i915/display: use intel_bo_to_drm_bo in intel_fbdev

We are preparing for Xe driver. I915 and Xe object implementation are
differing. Do not use  i915_gem_object->base directly. Instead use
intel_bo_to_drm_bo.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231115090719.3210079-3-jouni.hogander@intel.com

drm/i915/display: split i915 specific code from intel_fbdev

Split out code from intel_fbdev that can not be share between i915 and
xe. Create new i915 specific source/header file intel_fbdev_fb.[ch] which
contains this code.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231115090719.3210079-2-jouni.hogander@intel.com

drm/i915/display: Skip state verification with TBT-ALT mode

With TBT-ALT mode we are not programming C20 chip PLL's and
hence we don't need to check state verification. We don't
need to program DP link signal levels i.e.pre-emphasis and
voltage swing either.

This patch fixes dmesg errors like this one

"[drm] ERROR PHY F Write 0c06 failed after 3 retries."

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231129122221.1109084-1-mika.kahola@intel.com

drm/i915: add bool type checks in PIPE_CONF_CHECK_*

Avoid bool/int mismatches in state checker macros.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231129173317.1192269-2-jani.nikula@intel.com

drm/i915: use PIPE_CONF_CHECK_BOOL() for bool members

Don't treat bools as integers.

v2: Rebase

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231129173317.1192269-1-jani.nikula@intel.com

drm/i915/dgfx: DGFX uses direct VBT pin mapping

DDC pin mapping for DGFX cards uses direct VBT pin mapping

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128190329.1335562-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>

drm/i915/display: Fix IP version of the WAs

WAs 14011508470, 14011503030 were applied on IP versions beyond which
they are applicable. Fixed the IP version checks for these workarounds.

Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231128102451.825242-1-balasubramani.vivekanandan@intel.com

drm/i915: correct the input parameter on _intel_dsb_commit()

Current, the dewake_scanline variable is defined as unsigned int,
an unsigned int variable that is always greater than or equal to 0.
when _intel_dsb_commit function is called by intel_dsb_commit function,
the dewake_scanline variable may have an int value.
So the dewake_scanline variable is necessary to defined as an int.

Fixes: f83b94d23770 ("drm/i915/dsb: Use DEwake to combat PkgC latency")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310052201.AnVbpgPr-lkp@intel.com/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: heminhong <heminhong@kylinos.cn>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114024341.14524-1-heminhong@kylinos.cn

drm/i915/irq: Improve error logging for unexpected DE Misc interrupts

Dump the iir value in hex when the interrupt is unexpected.

Link: https://gitlab.freedesktop.org/drm/intel/-/issues/9652#note_2178501
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rahul Rameshbabu <sergeantsagara@protonmail.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231126214142.102106-1-sergeantsagara@protonmail.com

drm/i915: Clean up some DISPLAY_VER checks

Use the >= and < operators for the DISPLAY_VER checks everywhere.
This is what most of the code does, but especially recently random
pieces of code have started doing this differently for no good reason.

Conversion done with the following cocci:
@find@
expression i915;
constant ver;
@@
(
DISPLAY_VER(i915) <= ver
|
DISPLAY_VER(i915) > ver
)

@script:python inc@
old_ver << find.ver;
new_ver;
@@
coccinelle.new_ver = str(int(old_ver) + 1)

@@
expression find.i915;
constant find.ver;
identifier inc.new_ver;
@@
(
- DISPLAY_VER(i915) <= ver
+ DISPLAY_VER(i915) < new_ver
|
- DISPLAY_VER(i915) > ver
+ DISPLAY_VER(i915) >= new_ver
)

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/mst: Reject modes that require the bigjoiner

We have no bigjoiner support in the MST code, so .mode_valid()
pretending otherwise is just going to result black screens for
users. Reject any mode that needs the joiner.

Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: d51f25eb479a ("drm/i915: Add DSC support to MST path")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/mst: Fix .mode_valid_ctx() return values

.mode_valid_ctx() returns an errno, not the mode status. Fix
the code to do the right thing.

Cc: stable@vger.kernel.org
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: d51f25eb479a ("drm/i915: Add DSC support to MST path")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Skip some timing checks on BXT/GLK DSI transcoders

Apparently some BXT/GLK systems have DSI panels whose timings
don't agree with the normal cpu transcoder hblank>=32 limitation.
This is perhaps fine as there are no specific hblank/etc. limits
listed for the BXT/GLK DSI transcoders.

Move those checks out from the global intel_mode_valid() into
into connector specific .mode_valid() hooks, skipping BXT/GLK
DSI connectors. We'll leave the basic [hv]display/[hv]total
checks in intel_mode_valid() as those seem like sensible upper
limits regardless of the transcoder used.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9720
Fixes: 8f4b1068e7fc ("drm/i915: Check some transcoder timing minimum limits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231127145028.4899-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/psr: Include some basic PSR information in the state dump

Currently no one can figure out what the PSR code is doing since
we're including any of it in the basic state dump. Add at least the
bare minimum there.

v2: Also dump has_panel_replay (Jouni)

Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231124082735.25470-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915/xe2lpd: remove the FBC restriction if PSR2 is enabled

In earlier versions, FBC was restricted if PSR2 is enabled. From
xe2lpd onwards no such restrictions are needed anymore.

HSD: 14014305387
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110093225.39573-2-vinod.govindapillai@intel.com

drm/i915/psr: Add proper handling for disabling sel fetch for planes

Currently we are enabling selective fetch for all planes that are visible.
This is suboptimal as we might be fetching for memory for planes that are
not part of selective update.

Fix this by adding proper handling for disabling plane selective fetch:
If plane previously part of selective update is now not part of update:
Add it into updated planes and let the plane configuration to disable
selective fetch for it.

v3: Checkpatch warnings fixed
v2:
  - Add setting sel_fetch_area->y1/y2 to -1
  - Remove setting again local sel_fetch_area variable

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120082606.3156488-3-jouni.hogander@intel.com

drm/i915/psr: Move plane sel fetch configuration into plane source files

Currently selective fetch configuration for planes is implemented in psr
code. More suitable place for this code is where everything else is
configured for planes -> move it into skl_universal_plane.c and
intel_cursor.c. This also allows us to drop hooks for cursor handling.

v3: Checkpatch warnings fixed
v2: Removed setting sel_fetch_area->y1/y2 as -1

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231120082606.3156488-2-jouni.hogander@intel.com

drm/i915: Move the SDP split debug spew to the correct place

Adding ad-hoc debug prints all over the place is not good.
Move the SDP split debug spew into the proper place (state
dumper).

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231122093137.1509-4-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915: Stop printing pipe name as hex

Print the pipe name in ascii rather than hex.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231122093137.1509-3-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>

drm/i915: Fix glk+ degamma LUT conversions

The current implementation of change_lut_val_precision() is just
a convoluted way of shifting by 8. Implement the proper rounding
by just using drm_color_lut_extract() and intel_color_lut_pack()
like everyone else does.

And as the uapi can't handle >=1.0 values but the hardware
can we need to clamp the results appropriately in the readout
path.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013131402.24072-5-ville.syrjala@linux.intel.com
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: s/clamp()/min()/ in i965_lut_11p6_max_pack()

Use min() instead of clamp() since the color values
involved are unsigned. No functional changes.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231013131402.24072-4-ville.syrjala@linux.intel.com
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>