Baochen Qiang [Thu, 22 May 2025 08:54:11 +0000 (16:54 +0800)]
wifi: ath12k: parse and save sbs_lower_band_end_freq from WMI_SERVICE_READY_EXT2_EVENTID event
Firmware sends the boundary between lower and higher bands in
ath12k_wmi_dbs_or_sbs_cap_params structure embedded in
WMI_SERVICE_READY_EXT2_EVENTID event. The boundary is needed when
updating frequency range in the following patch. So parse and save
it for later use. Note ath12k_wmi_dbs_or_sbs_cap_params is placed
after some other structures, so placeholders for them are added
as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-2-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Baochen Qiang [Thu, 22 May 2025 08:54:10 +0000 (16:54 +0800)]
wifi: ath12k: parse and save hardware mode info from WMI_SERVICE_READY_EXT_EVENTID event for later use
WLAN hardware might support various hardware modes such as DBS (dual
band simultaneously), SBS (single band simultaneously) and DBS_OR_SBS
etc, see enum wmi_host_hw_mode_config_type. Firmware advertises actual
supported modes in WMI_SERVICE_READY_EXT_EVENTID event. For each mode,
firmware advertises frequency range each hardware MAC can operate on.
In MLO case such information is necessary during vdev activation and
link selection (which is done in following patches), so add a new
structure ath12k_svc_ext_info to ath12k_wmi_base, then parse and save
those information to it for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-1-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Bjorn Andersson [Tue, 10 Jun 2025 03:06:22 +0000 (22:06 -0500)]
wifi: ath12k: Avoid CPU busy-wait by handling VDEV_STAT and BCN_STAT
When the ath12k driver is built without CONFIG_ATH12K_DEBUG, the
recently refactored stats code can cause any user space application
(such at NetworkManager) to consume 100% CPU for 3 seconds, every time
stats are read.
Commit '
b8a0d83fe4c7 ("wifi: ath12k: move firmware stats out of
debugfs")' moved ath12k_debugfs_fw_stats_request() out of debugfs, by
merging the additional logic into ath12k_mac_get_fw_stats().
Among the added responsibility of ath12k_mac_get_fw_stats() was the
busy-wait for `fw_stats_done`.
Signalling of `fw_stats_done` happens when one of the
WMI_REQUEST_PDEV_STAT, WMI_REQUEST_VDEV_STAT, and WMI_REQUEST_BCN_STAT
messages are received, but the handling of the latter two commands remained
in the debugfs code. As `fw_stats_done` isn't signalled, the calling
processes will spin until the timeout (3 seconds) is reached.
Moving the handling of these two additional responses out of debugfs
resolves the issue.
Fixes:
b8a0d83fe4c7 ("wifi: ath12k: move firmware stats out of debugfs")
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://patch.msgid.link/20250609-ath12k-fw-stats-done-v1-1-2b3624656697@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Linus Torvalds [Thu, 12 Jun 2025 16:50:36 +0000 (09:50 -0700)]
Merge tag 'net-6.16-rc2' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
Linus Torvalds [Thu, 12 Jun 2025 15:21:13 +0000 (08:21 -0700)]
Merge tag 'pinctrl-v6.16-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Add some missing pins on the Qualcomm QCM2290, along with a managed
resources patch that make it clean and nice
- Drop an unused function in the ST Micro driver
- Drop bouncing MAINTAINER entry
- Drop of_match_ptr() macro to rid compile warnings in the TB10x
driver
- Fix up calculation of pin numbers from base in the Sunxi driver
* tag 'pinctrl-v6.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunxi: dt: Consider pin base when calculating bank number from pin
pinctrl: tb10x: Drop of_match_ptr for ID table
pinctrl: MAINTAINERS: Drop bouncing Jianlong Huang
pinctrl: st: Drop unused st_gpio_bank() function
pinctrl: qcom: pinctrl-qcm2290: Add missing pins
pinctrl: qcom: switch to devm_gpiochip_add_data()
Linus Torvalds [Thu, 12 Jun 2025 15:17:56 +0000 (08:17 -0700)]
Merge tag 'arc-6.16-rc1' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- arch_atomic64_cmpxchg relaxed variant [Jason]
- use of inbuilt swap in stack unwinder [Yu-Chun Lin]
- use of __ASSEMBLER__ in kernel headers [Thomas Huth]
* tag 'arc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Replace __ASSEMBLY__ with __ASSEMBLER__ in the non-uapi headers
ARC: Replace __ASSEMBLY__ with __ASSEMBLER__ in uapi headers
ARC: unwind: Use built-in sort swap to reduce code size and improve performance
ARC: atomics: Implement arch_atomic64_cmpxchg using _relaxed
Jakub Kicinski [Thu, 12 Jun 2025 15:16:47 +0000 (08:16 -0700)]
Merge tag 'wireless-2025-06-12' of https://git./linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Another quick round of updates:
- revert mwifiex HT40 that was causing issues
- many ath10k/ath11k/ath12k fixes
- re-add some iwlwifi code I lost in a merge
- use kfree_sensitive() on an error path in cfg80211
* tag 'wireless-2025-06-12' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: cfg80211: use kfree_sensitive() for connkeys cleanup
wifi: iwlwifi: fix merge damage related to iwl_pci_resume
Revert "wifi: mwifiex: Fix HT40 bandwidth issue."
wifi: ath12k: fix uaf in ath12k_core_init()
wifi: ath12k: Fix hal_reo_cmd_status kernel-doc
wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850
wifi: ath11k: validate ath11k_crypto_mode on top of ath11k_core_qmi_firmware_ready
wifi: ath11k: consistently use ath11k_mac_get_fw_stats()
wifi: ath11k: move locking outside of ath11k_mac_get_fw_stats()
wifi: ath11k: adjust unlock sequence in ath11k_update_stats_event()
wifi: ath11k: move some firmware stats related functions outside of debugfs
wifi: ath11k: don't wait when there is no vdev started
wifi: ath11k: don't use static variables in ath11k_debugfs_fw_stats_process()
wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
wil6210: fix support for sparrow chipsets
wifi: ath10k: Avoid vdev delete timeout when firmware is already down
ath10k: snoc: fix unbalanced IRQ enable in crash recovery
====================
Link: https://patch.msgid.link/20250612082519.11447-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 12 Jun 2025 15:15:37 +0000 (08:15 -0700)]
Merge branch 'fix-ntuple-rules-targeting-default-rss'
Gal Pressman says:
====================
Fix ntuple rules targeting default RSS
This series addresses a regression in ethtool flow steering where rules
targeting the default RSS context (context 0) were incorrectly rejected.
The default RSS context always exists but is not stored in the rss_ctx
xarray like additional contexts. The current validation logic was
checking for the existence of context 0 in this array, causing valid
flow steering rules to be rejected.
This prevented configurations such as:
- High priority rules directing specific traffic to the default context
- Low priority catch-all rules directing remaining traffic to additional
contexts
Patch 1 fixes the validation logic to skip the existence check for
context 0.
Patch 2 adds a selftest that verifies this behavior.
v3: https://lore.kernel.org/
20250609120250.
1630125-1-gal@nvidia.com
v2: https://lore.kernel.org/
20250225071348.509432-1-gal@nvidia.com
====================
Link: https://patch.msgid.link/20250612071958.1696361-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Thu, 12 Jun 2025 07:19:58 +0000 (10:19 +0300)]
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
Add test_rss_default_context_rule() to verify that ntuple rules can
correctly direct traffic to the default RSS context (context 0).
The test creates two ntuple rules with explicit location priorities:
- A high-priority rule (loc 0) directing specific port traffic to
context 0.
- A low-priority rule (loc 1) directing all other TCP traffic to context
1.
This validates that:
1. Rules targeting the default context function properly.
2. Traffic steering works as expected when mixing default and
additional RSS contexts.
The test was written by AI, and reviewed by humans.
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250612071958.1696361-3-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman [Thu, 12 Jun 2025 07:19:57 +0000 (10:19 +0300)]
net: ethtool: Don't check if RSS context exists in case of context 0
Context 0 (default context) always exists, there is no need to check
whether it exists or not when adding a flow steering rule.
The existing check fails when creating a flow steering rule for context
0 as it is not stored in the rss_ctx xarray.
For example:
$ ethtool --config-ntuple eth2 flow-type tcp4 dst-ip 194.237.147.23 dst-port 19983 context 0 loc 618
rmgr: Cannot insert RX class rule: Invalid argument
Cannot insert classification rule
An example usecase for this could be:
- A high-priority rule (loc 0) directing specific port traffic to
context 0.
- A low-priority rule (loc 1) directing all other TCP traffic to context
1.
This is a user-visible regression that was caught in our testing
environment, it was not reported by a user yet.
Fixes:
de7f7582dff2 ("net: ethtool: prevent flow steering to RSS contexts which don't exist")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20250612071958.1696361-2-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 12 Jun 2025 15:13:47 +0000 (08:13 -0700)]
Merge tag 'for-net-2025-06-11' of git://git./linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- eir: Fix NULL pointer deference on eir_get_service_data
- eir: Fix possible crashes on eir_create_adv_data
- hci_sync: Fix broadcast/PA when using an existing instance
- ISO: Fix using BT_SK_PA_SYNC to detect BIS sockets
- ISO: Fix not using bc_sid as advertisement SID
- MGMT: Fix sparse errors
* tag 'for-net-2025-06-11' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: MGMT: Fix sparse errors
Bluetooth: ISO: Fix not using bc_sid as advertisement SID
Bluetooth: ISO: Fix using BT_SK_PA_SYNC to detect BIS sockets
Bluetooth: eir: Fix possible crashes on eir_create_adv_data
Bluetooth: hci_sync: Fix broadcast/PA when using an existing instance
Bluetooth: Fix NULL pointer deference on eir_get_service_data
====================
Link: https://patch.msgid.link/20250611204944.1559356-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima [Wed, 11 Jun 2025 20:27:35 +0000 (13:27 -0700)]
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
Before the cited commit, the kernel unconditionally embedded SCM
credentials to skb for embryo sockets even when both the sender
and listener disabled SO_PASSCRED and SO_PASSPIDFD.
Now, the credentials are added to skb only when configured by the
sender or the listener.
However, as reported in the link below, it caused a regression for
some programs that assume credentials are included in every skb,
but sometimes not now.
The only problematic scenario would be that a socket starts listening
before setting the option. Then, there will be 2 types of non-small
race window, where a client can send skb without credentials, which
the peer receives as an "invalid" message (and aborts the connection
it seems ?):
Client Server
------ ------
s1.listen() <-- No SO_PASS{CRED,PIDFD}
s2.connect()
s2.send() <-- w/o cred
s1.setsockopt(SO_PASS{CRED,PIDFD})
s2.send() <-- w/ cred
or
Client Server
------ ------
s1.listen() <-- No SO_PASS{CRED,PIDFD}
s2.connect()
s2.send() <-- w/o cred
s3, _ = s1.accept() <-- Inherit cred options
s2.send() <-- w/o cred but not set yet
s3.setsockopt(SO_PASS{CRED,PIDFD})
s2.send() <-- w/ cred
It's unfortunate that buggy programs depend on the behaviour,
but let's restore the previous behaviour.
Fixes:
3f84d577b79d ("af_unix: Inherit sk_flags at connect().")
Reported-by: Jacek Łuczak <difrost.kernel@gmail.com>
Closes: https://lore.kernel.org/all/
68d38b0b-1666-4974-85d4-
15575789c8d4@gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Tested-by: Christian Heusel <christian@heusel.eu>
Tested-by: André Almeida <andrealmeid@igalia.com>
Tested-by: Jacek Łuczak <difrost.kernel@gmail.com>
Link: https://patch.msgid.link/20250611202758.3075858-1-kuni1840@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kuniyuki Iwashima [Wed, 11 Jun 2025 19:35:02 +0000 (12:35 -0700)]
ipv6: Move fib6_config_validate() to ip6_route_add().
syzkaller created an IPv6 route from a malformed packet, which has
a prefix len > 128, triggering the splat below. [0]
This is a similar issue fixed by commit
586ceac9acb7 ("ipv6: Restore
fib6_config validation for SIOCADDRT.").
The cited commit removed fib6_config validation from some callers
of ip6_add_route().
Let's move the validation back to ip6_route_add() and
ip6_route_multipath_add().
[0]:
UBSAN: array-index-out-of-bounds in ./include/net/ipv6.h:616:34
index 20 is out of range for type '__u8 [16]'
CPU: 1 UID: 0 PID: 7444 Comm: syz.0.708 Not tainted
6.16.0-rc1-syzkaller-g19272b37aa4f #0 PREEMPT
Hardware name: riscv-virtio,qemu (DT)
Call Trace:
[<
ffffffff80078a80>] dump_backtrace+0x2e/0x3c arch/riscv/kernel/stacktrace.c:132
[<
ffffffff8000327a>] show_stack+0x30/0x3c arch/riscv/kernel/stacktrace.c:138
[<
ffffffff80061012>] __dump_stack lib/dump_stack.c:94 [inline]
[<
ffffffff80061012>] dump_stack_lvl+0x12e/0x1a6 lib/dump_stack.c:120
[<
ffffffff800610a6>] dump_stack+0x1c/0x24 lib/dump_stack.c:129
[<
ffffffff8001c0ea>] ubsan_epilogue+0x14/0x46 lib/ubsan.c:233
[<
ffffffff819ba290>] __ubsan_handle_out_of_bounds+0xf6/0xf8 lib/ubsan.c:455
[<
ffffffff85b363a4>] ipv6_addr_prefix include/net/ipv6.h:616 [inline]
[<
ffffffff85b363a4>] ip6_route_info_create+0x8f8/0x96e net/ipv6/route.c:3793
[<
ffffffff85b635da>] ip6_route_add+0x2a/0x1aa net/ipv6/route.c:3889
[<
ffffffff85b02e08>] addrconf_prefix_route+0x2c4/0x4e8 net/ipv6/addrconf.c:2487
[<
ffffffff85b23bb2>] addrconf_prefix_rcv+0x1720/0x1e62 net/ipv6/addrconf.c:2878
[<
ffffffff85b92664>] ndisc_router_discovery+0x1a06/0x3504 net/ipv6/ndisc.c:1570
[<
ffffffff85b99038>] ndisc_rcv+0x500/0x600 net/ipv6/ndisc.c:1874
[<
ffffffff85bc2c18>] icmpv6_rcv+0x145e/0x1e0a net/ipv6/icmp.c:988
[<
ffffffff85af6798>] ip6_protocol_deliver_rcu+0x18a/0x1976 net/ipv6/ip6_input.c:436
[<
ffffffff85af8078>] ip6_input_finish+0xf4/0x174 net/ipv6/ip6_input.c:480
[<
ffffffff85af8262>] NF_HOOK include/linux/netfilter.h:317 [inline]
[<
ffffffff85af8262>] NF_HOOK include/linux/netfilter.h:311 [inline]
[<
ffffffff85af8262>] ip6_input+0x16a/0x70c net/ipv6/ip6_input.c:491
[<
ffffffff85af8dcc>] ip6_mc_input+0x5c8/0x1268 net/ipv6/ip6_input.c:588
[<
ffffffff85af6112>] dst_input include/net/dst.h:469 [inline]
[<
ffffffff85af6112>] ip6_rcv_finish net/ipv6/ip6_input.c:79 [inline]
[<
ffffffff85af6112>] NF_HOOK include/linux/netfilter.h:317 [inline]
[<
ffffffff85af6112>] NF_HOOK include/linux/netfilter.h:311 [inline]
[<
ffffffff85af6112>] ipv6_rcv+0x5ae/0x6e0 net/ipv6/ip6_input.c:309
[<
ffffffff85087e84>] __netif_receive_skb_one_core+0x106/0x16e net/core/dev.c:5977
[<
ffffffff85088104>] __netif_receive_skb+0x2c/0x144 net/core/dev.c:6090
[<
ffffffff850883c6>] netif_receive_skb_internal net/core/dev.c:6176 [inline]
[<
ffffffff850883c6>] netif_receive_skb+0x1aa/0xbf2 net/core/dev.c:6235
[<
ffffffff8328656e>] tun_rx_batched.isra.0+0x430/0x686 drivers/net/tun.c:1485
[<
ffffffff8329ed3a>] tun_get_user+0x2952/0x3d6c drivers/net/tun.c:1938
[<
ffffffff832a21e0>] tun_chr_write_iter+0xc4/0x21c drivers/net/tun.c:1984
[<
ffffffff80b9b9ae>] new_sync_write fs/read_write.c:593 [inline]
[<
ffffffff80b9b9ae>] vfs_write+0x56c/0xa9a fs/read_write.c:686
[<
ffffffff80b9c2be>] ksys_write+0x126/0x228 fs/read_write.c:738
[<
ffffffff80b9c42e>] __do_sys_write fs/read_write.c:749 [inline]
[<
ffffffff80b9c42e>] __se_sys_write fs/read_write.c:746 [inline]
[<
ffffffff80b9c42e>] __riscv_sys_write+0x6e/0x94 fs/read_write.c:746
[<
ffffffff80076912>] syscall_handler+0x94/0x118 arch/riscv/include/asm/syscall.h:112
[<
ffffffff8637e31e>] do_trap_ecall_u+0x396/0x530 arch/riscv/kernel/traps.c:341
[<
ffffffff863a69e2>] handle_exception+0x146/0x152 arch/riscv/kernel/entry.S:197
Fixes:
fa76c1674f2e ("ipv6: Move some validation from ip6_route_info_create() to rtm_to_fib6_config().")
Reported-by: syzbot+4c2358694722d304c44e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/
6849b8c3.
a00a0220.1eb5f5.00f0.GAE@google.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611193551.2999991-1-kuni1840@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 11 Jun 2025 17:46:43 +0000 (10:46 -0700)]
net: drv: netdevsim: don't napi_complete() from netpoll
netdevsim supports netpoll. Make sure we don't call napi_complete()
from it, since it may not be scheduled. Breno reports hitting a
warning in napi_complete_done():
WARNING: CPU: 14 PID: 104 at net/core/dev.c:6592 napi_complete_done+0x2cc/0x560
__napi_poll+0x2d8/0x3a0
handle_softirqs+0x1fe/0x710
This is presumably after netpoll stole the SCHED bit prematurely.
Reported-by: Breno Leitao <leitao@debian.org>
Fixes:
3762ec05a9fb ("netdevsim: add NAPI support")
Tested-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20250611174643.2769263-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Wed, 11 Jun 2025 13:14:32 +0000 (16:14 +0300)]
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
Check for if ida_alloc() or rhashtable_lookup_get_insert_fast() fails.
Fixes:
17e0accac577 ("net/mlx5: HWS, support complex matchers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Link: https://patch.msgid.link/aEmBONjyiF6z5yCV@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jesper Dangaard Brouer [Wed, 11 Jun 2025 12:40:04 +0000 (14:40 +0200)]
veth: prevent NULL pointer dereference in veth_xdp_rcv
The veth peer device is RCU protected, but when the peer device gets
deleted (veth_dellink) then the pointer is assigned NULL (via
RCU_INIT_POINTER).
This patch adds a necessary NULL check in veth_xdp_rcv when accessing
the veth peer net_device.
This fixes a bug introduced in commit
dc82a33297fc ("veth: apply qdisc
backpressure on full ptr_ring to reduce TX drops"). The bug is a race
and only triggers when having inflight packets on a veth that is being
deleted.
Reported-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Closes: https://lore.kernel.org/all/
fecfcad0-7a16-42b8-bff2-
66ee83a6e5c4@linux.dev/
Reported-by: syzbot+c4c7bf27f6b0c4bd97fe@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/
683da55e.
a00a0220.d8eae.0052.GAE@google.com/
Fixes:
dc82a33297fc ("veth: apply qdisc backpressure on full ptr_ring to reduce TX drops")
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Link: https://patch.msgid.link/174964557873.519608.10855046105237280978.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 12 Jun 2025 15:05:53 +0000 (08:05 -0700)]
Merge branch 'net_sched-no-longer-use-qdisc_tree_flush_backlog'
Eric Dumazet says:
====================
net_sched: no longer use qdisc_tree_flush_backlog()
This series is based on a report from Gerrard Tai.
Essentially, all users of qdisc_tree_flush_backlog() are racy.
We must instead use qdisc_purge_queue().
====================
Link: https://patch.msgid.link/20250611111515.1983366-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 11 Jun 2025 11:15:15 +0000 (11:15 +0000)]
net_sched: remove qdisc_tree_flush_backlog()
This function is no longer used after the four prior fixes.
Given all prior uses were wrong, it seems better to remove it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 11 Jun 2025 11:15:14 +0000 (11:15 +0000)]
net_sched: ets: fix a race in ets_qdisc_change()
Gerrard Tai reported a race condition in ETS, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes:
b05972f01e7d ("net: sched: tbf: don't call qdisc_put() while holding tree lock")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 11 Jun 2025 11:15:13 +0000 (11:15 +0000)]
net_sched: tbf: fix a race in tbf_change()
Gerrard Tai reported a race condition in TBF, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes:
b05972f01e7d ("net: sched: tbf: don't call qdisc_put() while holding tree lock")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://patch.msgid.link/20250611111515.1983366-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 11 Jun 2025 11:15:12 +0000 (11:15 +0000)]
net_sched: red: fix a race in __red_change()
Gerrard Tai reported a race condition in RED, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes:
0c8d13ac9607 ("net: sched: red: delay destroying child qdisc on replace")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 11 Jun 2025 11:15:11 +0000 (11:15 +0000)]
net_sched: prio: fix a race in prio_tune()
Gerrard Tai reported a race condition in PRIO, whenever SFQ perturb timer
fires at the wrong time.
The race is as follows:
CPU 0 CPU 1
[1]: lock root
[2]: qdisc_tree_flush_backlog()
[3]: unlock root
|
| [5]: lock root
| [6]: rehash
| [7]: qdisc_tree_reduce_backlog()
|
[4]: qdisc_put()
This can be abused to underflow a parent's qlen.
Calling qdisc_purge_queue() instead of qdisc_tree_flush_backlog()
should fix the race, because all packets will be purged from the qdisc
before releasing the lock.
Fixes:
7b8e0b6e6599 ("net: sched: prio: delay destroying child qdiscs on change")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Suggested-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250611111515.1983366-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 11 Jun 2025 08:35:01 +0000 (08:35 +0000)]
net_sched: sch_sfq: reject invalid perturb period
Gerrard Tai reported that SFQ perturb_period has no range check yet,
and this can be used to trigger a race condition fixed in a separate patch.
We want to make sure ctl->perturb_period * HZ will not overflow
and is positive.
Tested:
tc qd add dev lo root sfq perturb -10 # negative value : error
Error: sch_sfq: invalid perturb period.
tc qd add dev lo root sfq perturb
1000000000 # too big : error
Error: sch_sfq: invalid perturb period.
tc qd add dev lo root sfq perturb
2000000 # acceptable value
tc -s -d qd sh dev lo
qdisc sfq 8005: root refcnt 2 limit 127p quantum 64Kb depth 127 flows 128 divisor 1024 perturb 2000000sec
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250611083501.1810459-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Maxime Chevallier [Fri, 6 Jun 2025 09:43:20 +0000 (11:43 +0200)]
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
When performing a non-exact phy_caps lookup, we are looking for a
supported mode that matches as closely as possible the passed speed/duplex.
Blamed patch broke that logic by returning a match too early in case
the caller asks for half-duplex, as a full-duplex linkmode may match
first, and returned as a non-exact match without even trying to mach on
half-duplex modes.
Reported-by: Jijie Shao <shaojijie@huawei.com>
Closes: https://lore.kernel.org/netdev/
20250603102500.
4ec743cf@fedora/T/#m22ed60ca635c67dc7d9cbb47e8995b2beb5c1576
Tested-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Fixes:
fc81e257d19f ("net: phy: phy_caps: Allow looking-up link caps based on speed and duplex")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250606094321.483602-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 12 Jun 2025 02:00:20 +0000 (19:00 -0700)]
Merge tag 'bpf-fixes' of git://git./linux/kernel/git/bpf/bpf
Pull BPF fixes from Alexei Starovoitov
- Fix libbpf backward compatibility (Andrii Nakryiko)
- Add Stanislav Fomichev as bpf/net reviewer
- Fix resolve_btfid build when cross compiling (Suleiman Souhlal)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
MAINTAINERS: Add myself as bpf networking reviewer
tools/resolve_btfids: Fix build when cross compiling kernel with clang.
libbpf: Handle unsupported mmap-based /sys/kernel/btf/vmlinux correctly
Kuniyuki Iwashima [Tue, 10 Jun 2025 23:56:58 +0000 (23:56 +0000)]
MAINTAINERS: Update Kuniyuki Iwashima's email address.
I left Amazon and joined Google, so let's map the email
addresses accordingly.
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250610235734.88540-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 10 Jun 2025 00:12:45 +0000 (17:12 -0700)]
selftests: net: add test case for NAT46 looping back dst
Simple test for crash involving multicast loopback and stale dst.
Reuse exising NAT46 program.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250610001245.1981782-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 10 Jun 2025 00:12:44 +0000 (17:12 -0700)]
net: clear the dst when changing skb protocol
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address:
0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata.
Cc: stable@vger.kernel.org
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes:
d219df60a70e ("bpf: Add ipip6 and ip6ip decap support for bpf_skb_adjust_room()")
Fixes:
1b00e0dfe7d0 ("bpf: update skb->protocol in bpf_skb_net_grow")
Fixes:
6578171a7ff0 ("bpf: add bpf_skb_change_proto helper")
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250610001245.1981782-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Magnus Lindholm [Tue, 18 Feb 2025 17:55:14 +0000 (18:55 +0100)]
mm: pgtable: fix pte_swp_exclusive
Make pte_swp_exclusive return bool instead of int. This will better
reflect how pte_swp_exclusive is actually used in the code.
This fixes swap/swapoff problems on Alpha due pte_swp_exclusive not
returning correct values when _PAGE_SWP_EXCLUSIVE bit resides in upper
32-bits of PTE (like on alpha).
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Cc: Sam James <sam@gentoo.org>
Link: https://lore.kernel.org/lkml/20250218175735.19882-2-linmag7@gmail.com/
Link: https://lore.kernel.org/lkml/20250602041118.GA2675383@ZenIV/
[ Applied as the 'sed' script Al suggested - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jakub Kicinski [Wed, 11 Jun 2025 21:41:15 +0000 (14:41 -0700)]
Merge branch 'mlx5-misc-fixes-2025-06-10'
Mark Bloch says:
====================
mlx5 misc fixes 2025-06-10
This patchset includes misc fixes from the team for the mlx5 core
and Ethernet drivers.
====================
Link: https://patch.msgid.link/20250610151514.1094735-1-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shahar Shitrit [Tue, 10 Jun 2025 15:15:14 +0000 (18:15 +0300)]
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
When the link is up, either eth_proto_oper or ext_eth_proto_oper
typically reports the active link protocol, from which both speed
and number of lanes can be retrieved. However, in certain cases,
such as when a NIC is connected via a non-standard cable, the
firmware may not report the protocol.
In such scenarios, the speed can still be obtained from the
data_rate_oper field in PTYS register. Since data_rate_oper
provides only speed information and lacks lane details, it is
incorrect to derive the number of lanes from it.
This patch corrects the behavior by setting the number of lanes to
UNKNOWN instead of incorrectly using MAX_LANES when relying on
data_rate_oper.
Fixes:
7e959797f021 ("net/mlx5e: Enable lanes configuration when auto-negotiation is off")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-10-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jianbo Liu [Tue, 10 Jun 2025 15:15:13 +0000 (18:15 +0300)]
net/mlx5e: Fix leak of Geneve TLV option object
Previously, a unique tunnel id was added for the matching on TC
non-zero chains, to support inner header rewrite with goto action.
Later, it was used to support VF tunnel offload for vxlan, then for
Geneve and GRE. To support VF tunnel, a temporary mlx5_flow_spec is
used to parse tunnel options. For Geneve, if there is TLV option, a
object is created, or refcnt is added if already exists. But the
temporary mlx5_flow_spec is directly freed after parsing, which causes
the leak because no information regarding the object is saved in
flow's mlx5_flow_spec, which is used to free the object when deleting
the flow.
To fix the leak, call mlx5_geneve_tlv_option_del() before free the
temporary spec if it has TLV object.
Fixes:
521933cdc4aa ("net/mlx5e: Support Geneve and GRE with VF tunnel offload")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Alex Lazar <alazar@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-9-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vlad Dogaru [Tue, 10 Jun 2025 15:15:11 +0000 (18:15 +0300)]
net/mlx5: HWS, make sure the uplink is the last destination
When there are more than one destinations, we create a FW flow
table and provide it with all the destinations. FW requires to
have wire as the last destination in the list (if it exists),
otherwise the operation fails with FW syndrome.
This patch fixes the destination array action creation: if it
contains a wire destination, it is moved to the end.
Fixes:
504e536d9010 ("net/mlx5: HWS, added actions handling")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-7-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yevgeny Kliteynik [Tue, 10 Jun 2025 15:15:10 +0000 (18:15 +0300)]
net/mlx5: HWS, fix missing ip_version handling in definer
Fix missing field handling in definer - outer IP version.
Fixes:
74a778b4a63f ("net/mlx5: HWS, added definers handling")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-6-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vlad Dogaru [Tue, 10 Jun 2025 15:15:09 +0000 (18:15 +0300)]
net/mlx5: HWS, Init mutex on the correct path
The newly introduced mutex is only used for reformat actions, but it was
initialized for modify header instead.
The struct that contains the mutex is zero-initialized and an all-zero
mutex is valid, so the issue only shows up with CONFIG_DEBUG_MUTEXES.
Fixes:
b206d9ec19df ("net/mlx5: HWS, register reformat actions with fw")
Signed-off-by: Vlad Dogaru <vdogaru@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-5-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Patrisious Haddad [Tue, 10 Jun 2025 15:15:08 +0000 (18:15 +0300)]
net/mlx5: Fix return value when searching for existing flow group
When attempting to add a rule to an existing flow group, if a matching
flow group exists but is not active, the error code returned should be
EAGAIN, so that the rule can be added to the matching flow group once
it is active, rather than ENOENT, which indicates that no matching
flow group was found.
Fixes:
bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Gavi Teitz <gavi@nvidia.com>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-4-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amir Tzin [Tue, 10 Jun 2025 15:15:07 +0000 (18:15 +0300)]
net/mlx5: Fix ECVF vports unload on shutdown flow
Fix shutdown flow UAF when a virtual function is created on the embedded
chip (ECVF) of a BlueField device. In such case the vport acl ingress
table is not properly destroyed.
ECVF functionality is independent of ecpf_vport_exists capability and
thus functions mlx5_eswitch_(enable|disable)_pf_vf_vports() should not
test it when enabling/disabling ECVF vports.
kernel log:
[] refcount_t: underflow; use-after-free.
[] WARNING: CPU: 3 PID: 1 at lib/refcount.c:28
refcount_warn_saturate+0x124/0x220
----------------
[] Call trace:
[] refcount_warn_saturate+0x124/0x220
[] tree_put_node+0x164/0x1e0 [mlx5_core]
[] mlx5_destroy_flow_table+0x98/0x2c0 [mlx5_core]
[] esw_acl_ingress_table_destroy+0x28/0x40 [mlx5_core]
[] esw_acl_ingress_lgcy_cleanup+0x80/0xf4 [mlx5_core]
[] esw_legacy_vport_acl_cleanup+0x44/0x60 [mlx5_core]
[] esw_vport_cleanup+0x64/0x90 [mlx5_core]
[] mlx5_esw_vport_disable+0xc0/0x1d0 [mlx5_core]
[] mlx5_eswitch_unload_ec_vf_vports+0xcc/0x150 [mlx5_core]
[] mlx5_eswitch_disable_sriov+0x198/0x2a0 [mlx5_core]
[] mlx5_device_disable_sriov+0xb8/0x1e0 [mlx5_core]
[] mlx5_sriov_detach+0x40/0x50 [mlx5_core]
[] mlx5_unload+0x40/0xc4 [mlx5_core]
[] mlx5_unload_one_devl_locked+0x6c/0xe4 [mlx5_core]
[] mlx5_unload_one+0x3c/0x60 [mlx5_core]
[] shutdown+0x7c/0xa4 [mlx5_core]
[] pci_device_shutdown+0x3c/0xa0
[] device_shutdown+0x170/0x340
[] __do_sys_reboot+0x1f4/0x2a0
[] __arm64_sys_reboot+0x2c/0x40
[] invoke_syscall+0x78/0x100
[] el0_svc_common.constprop.0+0x54/0x184
[] do_el0_svc+0x30/0xac
[] el0_svc+0x48/0x160
[] el0t_64_sync_handler+0xa4/0x12c
[] el0t_64_sync+0x1a4/0x1a8
[] --[ end trace
9c4601d68c70030e ]---
Fixes:
a7719b29a821 ("net/mlx5: Add management of EC VF vports")
Reviewed-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Amir Tzin <amirtz@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-3-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Moshe Shemesh [Tue, 10 Jun 2025 15:15:06 +0000 (18:15 +0300)]
net/mlx5: Ensure fw pages are always allocated on same NUMA
When firmware asks the driver to allocate more pages, using event of
give_pages, the driver should always allocate it from same NUMA, the
original device NUMA. Current code uses dev_to_node() which can result
in different NUMA as it is changed by other driver flows, such as
mlx5_dma_zalloc_coherent_node(). Instead, use saved numa node for
allocating firmware pages.
Fixes:
311c7c71c9bb ("net/mlx5e: Allocate DMA coherent memory on reader NUMA node")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Link: https://patch.msgid.link/20250610151514.1094735-2-mbloch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 11 Jun 2025 21:28:51 +0000 (14:28 -0700)]
Merge branch '40GbE' of git://git./linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-06-10 (i40e, iavf, ice, e1000)
For i40e:
Robert Malz improves reset handling for situations where multiple reset
requests could cause some to be missed.
For iavf:
Ahmed adds detection, and handling, of reset that could occur early in
the initialization process to stop long wait/hangs.
For ice:
Anton, properly, sets missed use_nsecs value.
For e1000:
Joe Damato moves cancel_work_sync() call to avoid deadlock.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000: Move cancel_work_sync to avoid deadlock
ice/ptp: fix crosstimestamp reporting
iavf: fix reset_task for early reset event
i40e: retry VFLR handling if there is ongoing VF reset
i40e: return false from i40e_reset_vf if reset is in progress
====================
Link: https://patch.msgid.link/20250610171348.1476574-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luiz Augusto von Dentz [Wed, 11 Jun 2025 20:36:27 +0000 (16:36 -0400)]
Bluetooth: MGMT: Fix sparse errors
This fixes the following errors:
net/bluetooth/mgmt.c:5400:59: sparse: sparse: incorrect type in argument 3
(different base types) @@ expected unsigned short [usertype] handle @@
got restricted __le16 [usertype] monitor_handle @@
net/bluetooth/mgmt.c:5400:59: sparse: expected unsigned short [usertype] handle
net/bluetooth/mgmt.c:5400:59: sparse: got restricted __le16 [usertype] monitor_handle
Fixes:
e6ed54e86aae ("Bluetooth: MGMT: Fix UAF on mgmt_remove_adv_monitor_complete")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/
202506060347.ux2O1p7L-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Fri, 6 Jun 2025 18:32:49 +0000 (14:32 -0400)]
Bluetooth: ISO: Fix not using bc_sid as advertisement SID
Currently bc_sid is being ignore when acting as Broadcast Source role,
so this fix it by passing the bc_sid and then use it when programming
the PA:
< HCI Command: LE Set Exte.. (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 140.000 msec (0x00e0)
Max advertising interval: 140.000 msec (0x00e0)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x01
Scan request notifications: Disabled (0x00)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Mon, 9 Jun 2025 18:53:53 +0000 (14:53 -0400)]
Bluetooth: ISO: Fix using BT_SK_PA_SYNC to detect BIS sockets
BT_SK_PA_SYNC is only valid for Broadcast Sinks which means socket used
for Broadcast Sources wouldn't be able to use the likes of getpeername
to read out the sockaddr_iso_bc fields which may have been update (e.g.
bc_sid).
Fixes:
0a766a0affb5 ("Bluetooth: ISO: Fix getpeername not returning sockaddr_iso_bc fields")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 10 Jun 2025 14:14:35 +0000 (10:14 -0400)]
Bluetooth: eir: Fix possible crashes on eir_create_adv_data
eir_create_adv_data may attempt to add EIR_FLAGS and EIR_TX_POWER
without checking if that would fit.
Link: https://github.com/bluez/bluez/issues/1117#issuecomment-2958244066
Fixes:
01ce70b0a274 ("Bluetooth: eir: Move EIR/Adv Data functions to its own file")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Thu, 5 Jun 2025 15:15:16 +0000 (11:15 -0400)]
Bluetooth: hci_sync: Fix broadcast/PA when using an existing instance
When using and existing adv_info instance for broadcast source it
needs to be updated to periodic first before it can be reused, also in
case the existing instance already have data hci_set_adv_instance_data
cannot be used directly since it would overwrite the existing data so
this reappend the original data after the Broadcast ID, if one was
generated.
Example:
bluetoothctl># Add PBP to EA so it can be later referenced as the BIS ID
bluetoothctl> advertise.service 0x1856 0x00 0x00
bluetoothctl> advertise on
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 13
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x09
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
...
bluetoothctl># Attempt to acquire Broadcast Source transport
bluetoothctl>transport.acquire /org/bluez/hci0/pac_bcast0/fd0
...
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 255
Handle: 0x01
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x0e
Service Data: Broadcast Audio Announcement (0x1852)
Broadcast ID:
11371620 (0xad8464)
Service Data: Public Broadcast Announcement (0x1856)
Data[2]: 0000
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
Link: https://github.com/bluez/bluez/issues/1117
Fixes:
eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Thu, 5 Jun 2025 15:14:25 +0000 (11:14 -0400)]
Bluetooth: Fix NULL pointer deference on eir_get_service_data
The len parameter is considered optional so it can be NULL so it cannot
be used for skipping to next entry of EIR_SERVICE_DATA.
Fixes:
8f9ae5b3ae80 ("Bluetooth: eir: Add helpers for managing service data")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Herbert Xu [Wed, 28 May 2025 12:18:17 +0000 (13:18 +0100)]
KEYS: Invert FINAL_PUT bit
Invert the FINAL_PUT bit so that test_bit_acquire and clear_bit_unlock
can be used instead of smp_mb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jakub Raczynski [Mon, 9 Jun 2025 15:31:47 +0000 (17:31 +0200)]
net/mdiobus: Fix potential out-of-bounds clause 45 read/write access
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via C45 (clause 45) mdiobus,
there is no verification of parameters passed to the ioctl and
it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before C45 read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes:
4e4aafcddbbf ("net: mdio: Add dedicated C45 API to MDIO bus drivers")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Raczynski [Mon, 9 Jun 2025 15:31:46 +0000 (17:31 +0200)]
net/mdiobus: Fix potential out-of-bounds read/write access
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via mdiobus, there is no verification of
parameters passed to the ioctl and it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes:
080bb352fad00 ("net: phy: Maintain MDIO device and bus statistics")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zilin Guan [Fri, 23 May 2025 11:01:56 +0000 (11:01 +0000)]
wifi: cfg80211: use kfree_sensitive() for connkeys cleanup
The nl80211_parse_connkeys() function currently uses kfree() to release
the 'result' structure in error handling paths. However, if an error
occurs due to result->def being less than 0, the 'result' structure may
contain sensitive information.
To prevent potential leakage of sensitive data, replace kfree() with
kfree_sensitive() when freeing 'result'. This change aligns with the
approach used in its caller, nl80211_join_ibss(), enhancing the overall
security of the wireless subsystem.
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Link: https://patch.msgid.link/20250523110156.4017111-1-zilin@seu.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 11 Jun 2025 09:28:35 +0000 (11:28 +0200)]
Merge tag 'ath-current-
20250608' of git://git./linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git updates for v6.16-rc2
Fix a handful of both build and stability issues across multiple drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 3 Jun 2025 09:17:54 +0000 (12:17 +0300)]
wifi: iwlwifi: fix merge damage related to iwl_pci_resume
The changes I made in
wifi: iwlwifi: don't warn if the NIC is gone in resume
conflicted with a major rework done in this area.
The merge de-facto removed my changes.
Re-add them.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250603091754.70182-1-emmanuel.grumbach@intel.com
Fixes:
06c4b2036818 ("Merge tag 'iwlwifi-next-2025-05-15' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Francesco Dolcini [Thu, 5 Jun 2025 13:03:02 +0000 (15:03 +0200)]
Revert "wifi: mwifiex: Fix HT40 bandwidth issue."
This reverts commit
4fcfcbe45734 ("wifi: mwifiex: Fix HT40 bandwidth
issue.")
That commit introduces a regression, when HT40 mode is enabled,
received packets are lost, this was experience with W8997 with both
SDIO-UART and SDIO-SDIO variants. From an initial investigation the
issue solves on its own after some time, but it's not clear what is
the reason. Given that this was just a performance optimization, let's
revert it till we have a better understanding of the issue and a proper
fix.
Cc: Jeff Chen <jeff.chen_1@nxp.com>
Cc: stable@vger.kernel.org
Fixes:
4fcfcbe45734 ("wifi: mwifiex: Fix HT40 bandwidth issue.")
Closes: https://lore.kernel.org/all/
20250603203337.GA109929@francesco-nb/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20250605130302.55555-1-francesco@dolcini.it
[fix commit reference format]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Carlos Fernandez [Mon, 9 Jun 2025 07:26:26 +0000 (09:26 +0200)]
macsec: MACsec SCI assignment for ES = 0
According to 802.1AE standard, when ES and SC flags in TCI are zero,
used SCI should be the current active SC_RX. Current code uses the
header MAC address. Without this patch, when ES flag is 0 (using a
bridge or switch), header MAC will not fit the SCI and MACSec frames
will be discarted.
In order to test this issue, MACsec link should be stablished between
two interfaces, setting SC and ES flags to zero and a port identifier
different than one. For example, using ip macsec tools:
ip link add link $ETH0 macsec0 type macsec port 11 send_sci off
end_station off
ip macsec add macsec0 tx sa 0 pn 2 on key 01 $ETH1_KEY
ip macsec add macsec0 rx port 11 address $ETH1_MAC
ip macsec add macsec0 rx port 11 address $ETH1_MAC sa 0 pn 2 on key 02
ip link set dev macsec0 up
ip link add link $ETH1 macsec1 type macsec port 11 send_sci off
end_station off
ip macsec add macsec1 tx sa 0 pn 2 on key 01 $ETH0_KEY
ip macsec add macsec1 rx port 11 address $ETH0_MAC
ip macsec add macsec1 rx port 11 address $ETH0_MAC sa 0 pn 2 on key 02
ip link set dev macsec1 up
Fixes:
c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Co-developed-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de>
Signed-off-by: Andreu Montiel <Andreu.Montiel@technica-engineering.de>
Signed-off-by: Carlos Fernandez <carlos.fernandez@technica-engineering.de>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Mon, 9 Jun 2025 20:40:35 +0000 (22:40 +0200)]
net: airoha: Enable RX queues 16-31
Fix RX_DONE_INT_MASK definition in order to enable RX queues 16-31.
Fixes:
f252493e18353 ("net: airoha: Enable multiple IRQ lines support in airoha_eth driver.")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250609-aioha-fix-rx-queue-mask-v1-1-f33706a06fa2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gustavo Luiz Duarte [Mon, 9 Jun 2025 18:24:20 +0000 (11:24 -0700)]
netconsole: fix appending sysdata when sysdata_fields == SYSDATA_RELEASE
Before appending sysdata, prepare_extradata() checks if any feature is
enabled in sysdata_fields (and exits early if none is enabled).
When SYSDATA_RELEASE was introduced, we missed adding it to the list of
features being checked against sysdata_fields in prepare_extradata().
The result was that, if only SYSDATA_RELEASE is enabled in
sysdata_fields, we incorreclty exit early and fail to append the
release.
Instead of checking specific bits in sysdata_fields, check if
sysdata_fields has ALL bit zeroed and exit early if true. This fixes
case when only SYSDATA_RELEASE enabled and makes the code more general /
less error prone in future feature implementation.
Signed-off-by: Gustavo Luiz Duarte <gustavold@gmail.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Fixes:
cfcc9239e78a ("netconsole: append release to sysdata")
Link: https://patch.msgid.link/20250609-netconsole-fix-v1-1-17543611ae31@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michal Luczaj [Mon, 9 Jun 2025 17:08:03 +0000 (19:08 +0200)]
net: Fix TOCTOU issue in sk_is_readable()
sk->sk_prot->sock_is_readable is a valid function pointer when sk resides
in a sockmap. After the last sk_psock_put() (which usually happens when
socket is removed from sockmap), sk->sk_prot gets restored and
sk->sk_prot->sock_is_readable becomes NULL.
This makes sk_is_readable() racy, if the value of sk->sk_prot is reloaded
after the initial check. Which in turn may lead to a null pointer
dereference.
Ensure the function pointer does not turn NULL after the check.
Fixes:
8934ce2fd081 ("bpf: sockmap redirect ingress support")
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250609-skisreadable-toctou-v1-1-d0dfb2d62c37@rbox.co
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lucas Sanchez Sagrado [Mon, 9 Jun 2025 14:55:36 +0000 (16:55 +0200)]
net: usb: r8152: Add device ID for TP-Link UE200
The TP-Link UE200 is a RTL8152B based USB 2.0 Fast Ethernet adapter. This
patch adds its device ID. It has been tested on Ubuntu 22.04.5.
Signed-off-by: Lucas Sanchez Sagrado <lucsansag@gmail.com>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/20250609145536.26648-1-lucsansag@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stanislav Fomichev [Tue, 10 Jun 2025 17:54:37 +0000 (10:54 -0700)]
MAINTAINERS: Add myself as bpf networking reviewer
I've been focusing on networking BPF bits lately, add myself as a
reviewer.
Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com>
Acked-by: KP Singh <kpsingh@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20250610175442.2138504-1-stfomichev@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Tue, 10 Jun 2025 17:22:15 +0000 (10:22 -0700)]
Revert "mm/damon/Kconfig: enable CONFIG_DAMON by default"
This reverts commit
28615e6eed152f2fda5486680090b74aeed7b554.
No, we don't make random features default to being on.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: SeongJae Park <sj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Damato [Tue, 3 Jun 2025 16:34:01 +0000 (16:34 +0000)]
e1000: Move cancel_work_sync to avoid deadlock
Previously, e1000_down called cancel_work_sync for the e1000 reset task
(via e1000_down_and_stop), which takes RTNL.
As reported by users and syzbot, a deadlock is possible in the following
scenario:
CPU 0:
- RTNL is held
- e1000_close
- e1000_down
- cancel_work_sync (cancel / wait for e1000_reset_task())
CPU 1:
- process_one_work
- e1000_reset_task
- take RTNL
To remedy this, avoid calling cancel_work_sync from e1000_down
(e1000_reset_task does nothing if the device is down anyway). Instead,
call cancel_work_sync for e1000_reset_task when the device is being
removed.
Fixes:
e400c7444d84 ("e1000: Hold RTNL when e1000_down can be called")
Reported-by: syzbot+846bb38dc67fe62cc733@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/
683837bf.
a00a0220.52848.0003.GAE@google.com/
Reported-by: John <john.cs.hey@gmail.com>
Closes: https://lore.kernel.org/netdev/CAP=Rh=OEsn4y_2LvkO3UtDWurKcGPnZ_NPSXK=FbgygNXL37Sw@mail.gmail.com/
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Anton Nadezhdin [Tue, 20 May 2025 08:42:16 +0000 (10:42 +0200)]
ice/ptp: fix crosstimestamp reporting
Set use_nsecs=true as timestamp is reported in ns. Lack of this result
in smaller timestamp error window which cause error during phc2sys
execution on E825 NICs:
phc2sys[1768.256]: ioctl PTP_SYS_OFFSET_PRECISE: Invalid argument
This problem was introduced in the cited commit which omitted setting
use_nsecs to true when converting the ice driver to use
convert_base_to_cs().
Testing hints (ethX is PF netdev):
phc2sys -s ethX -c CLOCK_REALTIME -O 37 -m
phc2sys[1769.256]: CLOCK_REALTIME phc offset -5 s0 freq -0 delay 0
Fixes:
d4bea547ebb57 ("ice/ptp: Remove convert_art_to_tsc()")
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ahmed Zaki [Thu, 24 Apr 2025 13:50:13 +0000 (15:50 +0200)]
iavf: fix reset_task for early reset event
If a reset event is received from the PF early in the init cycle, the
state machine hangs for about 25 seconds.
Reproducer:
echo 1 > /sys/class/net/$PF0/device/sriov_numvfs
ip link set dev $PF0 vf 0 mac $NEW_MAC
The log shows:
[792.620416] ice 0000:5e:00.0: Enabling 1 VFs
[792.738812] iavf 0000:5e:01.0: enabling device (0000 -> 0002)
[792.744182] ice 0000:5e:00.0: Enabling 1 VFs with 17 vectors and 16 queues per VF
[792.839964] ice 0000:5e:00.0: Setting MAC 52:54:00:00:00:11 on VF 0. VF driver will be reinitialized
[813.389684] iavf 0000:5e:01.0: Failed to communicate with PF; waiting before retry
[818.635918] iavf 0000:5e:01.0: Hardware came out of reset. Attempting reinit.
[818.766273] iavf 0000:5e:01.0: Multiqueue Enabled: Queue pair count = 16
Fix it by scheduling the reset task and making the reset task capable of
resetting early in the init cycle.
Fixes:
ef8693eb90ae3 ("i40evf: refactor reset handling")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Robert Malz [Tue, 20 May 2025 08:31:52 +0000 (10:31 +0200)]
i40e: retry VFLR handling if there is ongoing VF reset
When a VFLR interrupt is received during a VF reset initiated from a
different source, the VFLR may be not fully handled. This can
leave the VF in an undefined state.
To address this, set the I40E_VFLR_EVENT_PENDING bit again during VFLR
handling if the reset is not yet complete. This ensures the driver
will properly complete the VF reset in such scenarios.
Fixes:
52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Robert Malz <robert.malz@canonical.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Robert Malz [Tue, 20 May 2025 08:31:51 +0000 (10:31 +0200)]
i40e: return false from i40e_reset_vf if reset is in progress
The function i40e_vc_reset_vf attempts, up to 20 times, to handle a
VF reset request, using the return value of i40e_reset_vf as an indicator
of whether the reset was successfully triggered. Currently, i40e_reset_vf
always returns true, which causes new reset requests to be ignored if a
different VF reset is already in progress.
This patch updates the return value of i40e_reset_vf to reflect when
another VF reset is in progress, allowing the caller to properly use
the retry mechanism.
Fixes:
52424f974bc5 ("i40e: Fix VF hang when reset is triggered on another VF")
Signed-off-by: Robert Malz <robert.malz@canonical.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Suleiman Souhlal [Fri, 6 Jun 2025 07:45:38 +0000 (16:45 +0900)]
tools/resolve_btfids: Fix build when cross compiling kernel with clang.
When cross compiling the kernel with clang, we need to override
CLANG_CROSS_FLAGS when preparing the step libraries.
Prior to commit
d1d096312176 ("tools: fix annoying "mkdir -p ..." logs
when building tools in parallel"), MAKEFLAGS would have been set to a
value that wouldn't set a value for CLANG_CROSS_FLAGS, hiding the
fact that we weren't properly overriding it.
Fixes:
56a2df7615fa ("tools/resolve_btfids: Compile resolve_btfids as host program")
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/bpf/20250606074538.1608546-1-suleiman@google.com
Chen-Yu Tsai [Sat, 7 Jun 2025 13:52:03 +0000 (21:52 +0800)]
pinctrl: sunxi: dt: Consider pin base when calculating bank number from pin
In prepare_function_table() when the pinctrl function table IRQ entries
are generated, the pin bank is calculated from the absolute pin number;
however the IRQ bank mux array is indexed from the first pin bank of the
controller. For R_PIO controllers, this means the absolute pin bank is
way off from the relative pin bank used for array indexing.
Correct this by taking into account the pin base of the controller.
Fixes:
f5e2cd34b12f ("pinctrl: sunxi: allow reading mux values from DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/20250607135203.2085226-1-wens@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Tue, 10 Jun 2025 03:06:58 +0000 (20:06 -0700)]
Merge tag 'powerpc-6.16-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Madhavan Srinivasan:
- a couple of fixes for out of bounds issues in memtrace and vas
Thanks to Ritesh Harjani (IBM), Haren Myneni, and Jonathan Greental
* tag 'powerpc-6.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/vas: Return -EINVAL if the offset is non-zero in mmap()
powerpc/powernv/memtrace: Fix out of bounds issue in memtrace mmap
Haren Myneni [Tue, 10 Jun 2025 02:12:27 +0000 (07:42 +0530)]
powerpc/vas: Return -EINVAL if the offset is non-zero in mmap()
The user space calls mmap() to map VAS window paste address
and the kernel returns the complete mapped page for each
window. So return -EINVAL if non-zero is passed for offset
parameter to mmap().
See Documentation/arch/powerpc/vas-api.rst for mmap()
restrictions.
Co-developed-by: Jonathan Greental <yonatan02greental@gmail.com>
Signed-off-by: Jonathan Greental <yonatan02greental@gmail.com>
Reported-by: Jonathan Greental <yonatan02greental@gmail.com>
Fixes:
dda44eb29c23 ("powerpc/vas: Add VAS user space API")
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610021227.361980-2-maddy@linux.ibm.com
Ritesh Harjani (IBM) [Tue, 10 Jun 2025 02:12:26 +0000 (07:42 +0530)]
powerpc/powernv/memtrace: Fix out of bounds issue in memtrace mmap
memtrace mmap issue has an out of bounds issue. This patch fixes the by
checking that the requested mapping region size should stay within the
allocated region size.
Reported-by: Jonathan Greental <yonatan02greental@gmail.com>
Fixes:
08a022ad3dfa ("powerpc/powernv/memtrace: Allow mmaping trace buffers")
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610021227.361980-1-maddy@linux.ibm.com
Jakub Kicinski [Mon, 9 Jun 2025 22:47:29 +0000 (15:47 -0700)]
Merge tag 'for-net-2025-06-05' of git://git./linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- MGMT: Fix UAF on mgmt_remove_adv_monitor_complete
- MGMT: Protect mgmt_pending list with its own lock
- hci_core: fix list_for_each_entry_rcu usage
- btintel_pcie: Increase the tx and rx descriptor count
- btintel_pcie: Reduce driver buffer posting to prevent race condition
- btintel_pcie: Fix driver not posting maximum rx buffers
* tag 'for-net-2025-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: MGMT: Protect mgmt_pending list with its own lock
Bluetooth: MGMT: Fix UAF on mgmt_remove_adv_monitor_complete
Bluetooth: btintel_pcie: Reduce driver buffer posting to prevent race condition
Bluetooth: btintel_pcie: Increase the tx and rx descriptor count
Bluetooth: btintel_pcie: Fix driver not posting maximum rx buffers
Bluetooth: hci_core: fix list_for_each_entry_rcu usage
====================
Link: https://patch.msgid.link/20250605191136.904411-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Fri, 6 Jun 2025 16:51:27 +0000 (16:51 +0000)]
net_sched: sch_sfq: fix a potential crash on gso_skb handling
SFQ has an assumption of always being able to queue at least one packet.
However, after the blamed commit, sch->q.len can be inflated by packets
in sch->gso_skb, and an enqueue() on an empty SFQ qdisc can be followed
by an immediate drop.
Fix sfq_drop() to properly clear q->tail in this situation.
Tested:
ip netns add lb
ip link add dev to-lb type veth peer name in-lb netns lb
ethtool -K to-lb tso off # force qdisc to requeue gso_skb
ip netns exec lb ethtool -K in-lb gro on # enable NAPI
ip link set dev to-lb up
ip -netns lb link set dev in-lb up
ip addr add dev to-lb 192.168.20.1/24
ip -netns lb addr add dev in-lb 192.168.20.2/24
tc qdisc replace dev to-lb root sfq limit 100
ip netns exec lb netserver
netperf -H 192.168.20.2 -l 100 &
netperf -H 192.168.20.2 -l 100 &
netperf -H 192.168.20.2 -l 100 &
netperf -H 192.168.20.2 -l 100 &
Fixes:
a53851e2c321 ("net: sched: explicit locking in gso_cpu fallback")
Reported-by: Marcus Wichelmann <marcus.wichelmann@hetzner-cloud.de>
Closes: https://lore.kernel.org/netdev/
9da42688-bfaa-4364-8797-
e9271f3bdaef@hetzner-cloud.de/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20250606165127.3629486-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thomas Huth [Fri, 14 Mar 2025 07:09:36 +0000 (08:09 +0100)]
ARC: Replace __ASSEMBLY__ with __ASSEMBLER__ in the non-uapi headers
While the GCC and Clang compilers already define __ASSEMBLER__
automatically when compiling assembly code, __ASSEMBLY__ is a
macro that only gets defined by the Makefiles in the kernel.
This can be very confusing when switching between userspace
and kernelspace coding, or when dealing with uapi headers that
rather should use __ASSEMBLER__ instead. So let's standardize on
the __ASSEMBLER__ macro that is provided by the compilers now.
This is a completely mechanical patch (done with a simple "sed -i"
statement).
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Thomas Huth [Fri, 14 Mar 2025 07:09:35 +0000 (08:09 +0100)]
ARC: Replace __ASSEMBLY__ with __ASSEMBLER__ in uapi headers
__ASSEMBLY__ is only defined by the Makefile of the kernel, so
this is not really useful for uapi headers (unless the userspace
Makefile defines it, too). Let's switch to __ASSEMBLER__ which
gets set automatically by the compiler when compiling assembly
code.
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Yu-Chun Lin [Wed, 9 Apr 2025 17:11:16 +0000 (01:11 +0800)]
ARC: unwind: Use built-in sort swap to reduce code size and improve performance
The custom swap function used in sort() was identical to the default
built-in sort swap. Remove the custom swap function and passes NULL to
sort(), allowing it to use the default swap function.
This change reduces code size and improves performance, particularly when
CONFIG_MITIGATION_RETPOLINE is enabled. With RETPOLINE mitigation, indirect
function calls incur significant overhead, and using the default swap
function avoids this cost.
$ ./scripts/bloat-o-meter ./unwind.o.old ./unwind.o.new
add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-22 (-22)
Function old new delta
init_unwind_hdr.constprop 544 540 -4
swap_eh_frame_hdr_table_entries 18 - -18
Total: Before=4410, After=4388, chg -0.50%
Signed-off-by: Yu-Chun Lin <eleanor15x@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Jason Gunthorpe [Tue, 8 Apr 2025 17:22:56 +0000 (14:22 -0300)]
ARC: atomics: Implement arch_atomic64_cmpxchg using _relaxed
The core atomic code has a number of macros where it elaborates
architecture primitives into more functions. ARC uses
arch_atomic64_cmpxchg() as it's architecture primitive which disable alot
of the additional functions.
Instead provide arch_cmpxchg64_relaxed() as the primitive and rely on the
core macros to create arch_cmpxchg64().
The macros will also provide other functions, for instance,
try_cmpxchg64_release(), giving a more complete implementation.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/Z0747n5bSep4_1VX@J2N7QTR9R3
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
Krzysztof Kozlowski [Sun, 1 Jun 2025 10:51:01 +0000 (12:51 +0200)]
pinctrl: tb10x: Drop of_match_ptr for ID table
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF warning:
pinctrl-tb10x.c:815:34: warning: unused variable 'tb10x_pinctrl_dt_ids' [-Wunused-const-variable]
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/
202505301317.EI1caRC0-lkp@intel.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250601105100.27927-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Krzysztof Kozlowski [Wed, 28 May 2025 10:45:15 +0000 (12:45 +0200)]
pinctrl: MAINTAINERS: Drop bouncing Jianlong Huang
Emails to Jianlong Huang bounce since 9 months, so drop the person from
maintainers:
550 5.4.1 Recipient address rejected: Access denied.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250528104514.184122-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Krzysztof Kozlowski [Wed, 28 May 2025 09:22:02 +0000 (11:22 +0200)]
pinctrl: st: Drop unused st_gpio_bank() function
Static inline st_gpio_bank() function is not referenced:
pinctrl-st.c:377:19: error: unused function 'st_gpio_bank' [-Werror,-Wunused-function]
Fixes:
701016c0cba5 ("pinctrl: st: Add pinctrl and pinconf support.")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250528092201.52132-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wojciech Slenska [Fri, 23 May 2025 10:14:37 +0000 (12:14 +0200)]
pinctrl: qcom: pinctrl-qcm2290: Add missing pins
Added the missing pins to the qcm2290_pins table.
Signed-off-by: Wojciech Slenska <wojciech.slenska@gmail.com>
Fixes:
48e049ef1238 ("pinctrl: qcom: Add QCM2290 pinctrl driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250523101437.59092-1-wojciech.slenska@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dmitry Baryshkov [Tue, 13 May 2025 18:38:59 +0000 (21:38 +0300)]
pinctrl: qcom: switch to devm_gpiochip_add_data()
In order to simplify cleanup actions, use devres-enabled version of
gpiochip_add_data(). As the msm_pinctrl_remove() function is now empty,
drop it and all its calls from the corresponding pinctrl drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/20250513-pinctrl-msm-fix-v2-3-249999af0fc1@oss.qualcomm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Sun, 8 Jun 2025 20:44:43 +0000 (13:44 -0700)]
Linux 6.16-rc1
Linus Torvalds [Sun, 8 Jun 2025 18:44:41 +0000 (11:44 -0700)]
Merge tag 'turbostat-2025.06.08' of git://git./linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Add initial DMR support, which required smarter RAPL probe
- Fix AMD MSR RAPL energy reporting
- Add RAPL power limit configuration output
- Minor fixes
* tag 'turbostat-2025.06.08' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: version 2025.06.08
tools/power turbostat: Add initial support for BartlettLake
tools/power turbostat: Add initial support for DMR
tools/power turbostat: Dump RAPL sysfs info
tools/power turbostat: Avoid probing the same perf counters
tools/power turbostat: Allow probing RAPL with platform_features->rapl_msrs cleared
tools/power turbostat: Clean up add perf/msr counter logic
tools/power turbostat: Introduce add_msr_counter()
tools/power turbostat: Remove add_msr_perf_counter_()
tools/power turbostat: Remove add_cstate_perf_counter_()
tools/power turbostat: Remove add_rapl_perf_counter_()
tools/power turbostat: Quit early for unsupported RAPL counters
tools/power turbostat: Always check rapl_joules flag
tools/power turbostat: Fix AMD package-energy reporting
tools/power turbostat: Fix RAPL_GFX_ALL typo
tools/power turbostat: Add Android support for MSR device handling
tools/power turbostat.8: pm_domain wording fix
tools/power turbostat.8: fix typo: idle_pct should be pct_idle
Linus Torvalds [Sun, 8 Jun 2025 18:33:00 +0000 (11:33 -0700)]
Merge tag 'timers-cleanups-2025-06-08' of git://git./linux/kernel/git/tip/tip
Pull timer cleanup from Thomas Gleixner:
"The delayed from_timer() API cleanup:
The renaming to the timer_*() namespace was delayed due massive
conflicts against Linux-next. Now that everything is upstream finish
the conversion"
* tag 'timers-cleanups-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
treewide, timers: Rename from_timer() to timer_container_of()
Linus Torvalds [Sun, 8 Jun 2025 18:27:20 +0000 (11:27 -0700)]
Merge tag 'x86-urgent-2025-06-08' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of x86 fixes:
- Cure IO bitmap inconsistencies
A failed fork cleans up all resources of the newly created thread
via exit_thread(). exit_thread() invokes io_bitmap_exit() which
does the IO bitmap cleanups, which unfortunately assume that the
cleanup is related to the current task, which is obviously bogus.
Make it work correctly
- A lockdep fix in the resctrl code removed the clearing of the
command buffer in two places, which keeps stale error messages
around. Bring them back.
- Remove unused trace events"
* tag 'x86-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
fs/resctrl: Restore the rdt_last_cmd_clear() calls after acquiring rdtgroup_mutex
x86/iopl: Cure TIF_IO_BITMAP inconsistencies
x86/fpu: Remove unused trace events
Linus Torvalds [Sun, 8 Jun 2025 18:25:13 +0000 (11:25 -0700)]
Merge tag 'timers-urgent-2025-06-08' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"Add the missing seq_file forward declaration in the timer namespace
header"
* tag 'timers-urgent-2025-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timens: Add struct seq_file forward declaration
Len Brown [Sun, 8 Jun 2025 16:31:59 +0000 (12:31 -0400)]
tools/power turbostat: version 2025.06.08
Add initial DMR support, which required smarter RAPL probe
Fix AMD MSR RAPL energy reporting
Add RAPL power limit configuration output
Minor fixes
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Fri, 18 Apr 2025 06:04:26 +0000 (14:04 +0800)]
tools/power turbostat: Add initial support for BartlettLake
Add initial support for BartlettLake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Mon, 4 Mar 2024 06:54:40 +0000 (14:54 +0800)]
tools/power turbostat: Add initial support for DMR
Add initial support for DMR.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Fri, 30 May 2025 06:01:31 +0000 (14:01 +0800)]
tools/power turbostat: Dump RAPL sysfs info
for example:
intel-rapl:1: psys 28.0s:100W 976.0us:100W
intel-rapl:0: package-0 28.0s:57W,max:15W 2.4ms:57W
intel-rapl:0/intel-rapl:0:0: core disabled
intel-rapl:0/intel-rapl:0:1: uncore disabled
intel-rapl-mmio:0: package-0 28.0s:28W,max:15W 2.4ms:57W
[lenb: simplified format]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
squish me
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Fri, 30 May 2025 00:09:28 +0000 (08:09 +0800)]
tools/power turbostat: Avoid probing the same perf counters
For the RAPL package energy status counter, Intel and AMD share the same
perf_subsys and perf_name, but with different MSR addresses.
Both rapl_counter_arch_infos[0] and rapl_counter_arch_infos[1] are
introduced to describe this counter for different Vendors.
As a result, the perf counter is probed twice, and causes a failure in
in get_rapl_counters() because expected_read_size and actual_read_size
don't match.
Fix the problem by skipping the already probed counter.
Note, this is not a perfect fix. For example, if different
vendors/platforms use the same MSR value for different purpose, the code
can be fooled when it probes a rapl_counter_arch_infos[] entry that does
not belong to the running Vendor/Platform.
In a long run, better to put rapl_counter_arch_infos[] into the
platform_features so that this becomes Vendor/Platform specific.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 09:44:50 +0000 (17:44 +0800)]
tools/power turbostat: Allow probing RAPL with platform_features->rapl_msrs cleared
platform_features->rapl_msrs describes the RAPL MSRs supported. While
RAPL Perf counters can be exposed from different kernel backend drivers,
e.g. RAPL MSR I/F driver, or RAPL TPMI I/F driver.
Thus, turbostat should first blindly probe all the available RAPL Perf
counters, and falls back to the RAPL MSR counters if they are listed in
platform_features->rapl_msrs.
With this, platforms that don't have RAPL MSRs can clear the
platform_features->rapl_msrs bits and use RAPL Perf counters only.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 09:35:17 +0000 (17:35 +0800)]
tools/power turbostat: Clean up add perf/msr counter logic
Increase the code readability by moving the no_perf/no_msr flag and the
cai->perf_name/cai->msr sanity checks into the counter probe functions.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 07:58:51 +0000 (15:58 +0800)]
tools/power turbostat: Introduce add_msr_counter()
probe_rapl_msr() is reused for probing RAPL MSR counters, cstate MSR
counters and MPERF/APERF/SMI MSR counters, thus its name is misleading.
Similar to add_perf_counter(), introduce add_msr_counter() to probe a
counter via MSR. Introduce wrapper function add_rapl_msr_counter() at
the same time to add extra check for Zero return value for specified
RAPL counters.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 09:40:08 +0000 (17:40 +0800)]
tools/power turbostat: Remove add_msr_perf_counter_()
As the only caller of add_msr_perf_counter_(), add_msr_perf_counter()
just gives extra debug output on top. There is no need to keep both
functions.
Remove add_msr_perf_counter_() and move all the logic to
add_msr_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 07:43:59 +0000 (15:43 +0800)]
tools/power turbostat: Remove add_cstate_perf_counter_()
As the only caller of add_cstate_perf_counter_(),
add_cstate_perf_counter() just gives extra debug output on top. There is
no need to keep both functions.
Remove add_cstate_perf_counter_() and move all the logic to
add_cstate_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 04:06:22 +0000 (12:06 +0800)]
tools/power turbostat: Remove add_rapl_perf_counter_()
As the only caller of add_rapl_perf_counter_(), add_rapl_perf_counter()
just gives extra debug output on top. There is no need to keep both
functions.
Remove add_rapl_perf_counter_() and move all the logic to
add_rapl_perf_counter().
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Sat, 17 May 2025 02:26:14 +0000 (10:26 +0800)]
tools/power turbostat: Quit early for unsupported RAPL counters
Quit early for unsupported RAPL counters.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Fri, 30 May 2025 06:00:33 +0000 (14:00 +0800)]
tools/power turbostat: Always check rapl_joules flag
rapl_joules bit should always be checked even if
platform_features->rapl_msrs is not set or no_msr flag is used.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Gautham R. Shenoy [Thu, 29 May 2025 11:48:25 +0000 (17:18 +0530)]
tools/power turbostat: Fix AMD package-energy reporting
commit
05a2f07db888 ("tools/power turbostat: read RAPL counters via
perf") that adds support to read RAPL counters via perf defines the
notion of a RAPL domain_id which is set to physical_core_id on
platforms which support per_core_rapl counters (Eg: AMD processors
Family 17h onwards) and is set to the physical_package_id on all the
other platforms.
However, the physical_core_id is only unique within a package and on
platforms with multiple packages more than one core can have the same
physical_core_id and thus the same domain_id. (For eg, the first cores
of each package have the physical_core_id = 0). This results in all
these cores with the same physical_core_id using the same entry in the
rapl_counter_info_perdomain[]. Since rapl_perf_init() skips the
perf-initialization for cores whose domain_ids have already been
visited, cores that have the same physical_core_id always read the
perf file corresponding to the physical_core_id of the first package
and thus the package-energy is incorrectly reported to be the same
value for different packages.
Note: This issue only arises when RAPL counters are read via perf and
not when they are read via MSRs since in the latter case the MSRs are
read separately on each core.
Fix this issue by associating each CPU with rapl_core_id which is
unique across all the packages in the system.
Fixes:
05a2f07db888 ("tools/power turbostat: read RAPL counters via perf")
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Kaushlendra Kumar [Fri, 23 May 2025 08:06:59 +0000 (13:36 +0530)]
tools/power turbostat: Fix RAPL_GFX_ALL typo
Fix typo in the currently unused RAPL_GFX_ALL macro definition.
Signed-off-by: Kaushlendra Kumar <kaushlendra.kumar@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
projects / linux-block.git / log