#include "ksz9477.h"
#include "lan937x.h"
+/* marker for ports without built-in PHY */
+#define LAN937X_NO_PHY U8_MAX
+
+/*
+ * lan9370_phy_addr - Mapping of LAN9370 switch ports to PHY addresses.
+ *
+ * Each entry corresponds to a specific port on the LAN9370 switch,
+ * where ports 1-4 are connected to integrated 100BASE-T1 PHYs, and
+ * Port 5 is connected to an RGMII interface without a PHY. The values
+ * are based on the documentation (DS00003108E, section 3.3).
+ */
+static const u8 lan9370_phy_addr[] = {
+ [0] = 2, /* Port 1, T1 AFE0 */
+ [1] = 3, /* Port 2, T1 AFE1 */
+ [2] = 5, /* Port 3, T1 AFE3 */
+ [3] = 6, /* Port 4, T1 AFE4 */
+ [4] = LAN937X_NO_PHY, /* Port 5, RGMII 2 */
+};
+
+/*
+ * lan9371_phy_addr - Mapping of LAN9371 switch ports to PHY addresses.
+ *
+ * The values are based on the documentation (DS00003109E, section 3.3).
+ */
+static const u8 lan9371_phy_addr[] = {
+ [0] = 2, /* Port 1, T1 AFE0 */
+ [1] = 3, /* Port 2, T1 AFE1 */
+ [2] = 5, /* Port 3, T1 AFE3 */
+ [3] = 8, /* Port 4, TX PHY */
+ [4] = LAN937X_NO_PHY, /* Port 5, RGMII 2 */
+ [5] = LAN937X_NO_PHY, /* Port 6, RGMII 1 */
+};
+
+/*
+ * lan9372_phy_addr - Mapping of LAN9372 switch ports to PHY addresses.
+ *
+ * The values are based on the documentation (DS00003110F, section 3.3).
+ */
+static const u8 lan9372_phy_addr[] = {
+ [0] = 2, /* Port 1, T1 AFE0 */
+ [1] = 3, /* Port 2, T1 AFE1 */
+ [2] = 5, /* Port 3, T1 AFE3 */
+ [3] = 8, /* Port 4, TX PHY */
+ [4] = LAN937X_NO_PHY, /* Port 5, RGMII 2 */
+ [5] = LAN937X_NO_PHY, /* Port 6, RGMII 1 */
+ [6] = 6, /* Port 7, T1 AFE4 */
+ [7] = 4, /* Port 8, T1 AFE2 */
+};
+
+/*
+ * lan9373_phy_addr - Mapping of LAN9373 switch ports to PHY addresses.
+ *
+ * The values are based on the documentation (DS00003110F, section 3.3).
+ */
+static const u8 lan9373_phy_addr[] = {
+ [0] = 2, /* Port 1, T1 AFE0 */
+ [1] = 3, /* Port 2, T1 AFE1 */
+ [2] = 5, /* Port 3, T1 AFE3 */
+ [3] = LAN937X_NO_PHY, /* Port 4, SGMII */
+ [4] = LAN937X_NO_PHY, /* Port 5, RGMII 2 */
+ [5] = LAN937X_NO_PHY, /* Port 6, RGMII 1 */
+ [6] = 6, /* Port 7, T1 AFE4 */
+ [7] = 4, /* Port 8, T1 AFE2 */
+};
+
+/*
+ * lan9374_phy_addr - Mapping of LAN9374 switch ports to PHY addresses.
+ *
+ * The values are based on the documentation (DS00003110F, section 3.3).
+ */
+static const u8 lan9374_phy_addr[] = {
+ [0] = 2, /* Port 1, T1 AFE0 */
+ [1] = 3, /* Port 2, T1 AFE1 */
+ [2] = 5, /* Port 3, T1 AFE3 */
+ [3] = 7, /* Port 4, T1 AFE5 */
+ [4] = LAN937X_NO_PHY, /* Port 5, RGMII 2 */
+ [5] = LAN937X_NO_PHY, /* Port 6, RGMII 1 */
+ [6] = 6, /* Port 7, T1 AFE4 */
+ [7] = 4, /* Port 8, T1 AFE2 */
+};
+
static int lan937x_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
{
return regmap_update_bits(ksz_regmap_8(dev), addr, bits, set ? bits : 0);
bits, set ? bits : 0);
}
-static int lan937x_enable_spi_indirect_access(struct ksz_device *dev)
+/**
+ * lan937x_create_phy_addr_map - Create port-to-PHY address map for MDIO bus.
+ * @dev: Pointer to device structure.
+ * @side_mdio: Boolean indicating if the PHYs are accessed over a side MDIO bus.
+ *
+ * This function sets up the PHY address mapping for the LAN937x switches,
+ * which support two access modes for internal PHYs:
+ * 1. **SPI Access**: A straightforward one-to-one port-to-PHY address
+ * mapping is applied.
+ * 2. **MDIO Access**: The PHY address mapping varies based on chip variant
+ * and strap configuration. An offset is calculated based on strap settings
+ * to ensure correct PHY addresses are assigned. The offset calculation logic
+ * is based on Microchip's Article Number 000015828, available at:
+ * https://microchip.my.site.com/s/article/LAN9374-Virtual-PHY-PHY-Address-Mapping
+ *
+ * The function first checks if side MDIO access is disabled, in which case a
+ * simple direct mapping (port number = PHY address) is applied. If side MDIO
+ * access is enabled, it reads the strap configuration to determine the correct
+ * offset for PHY addresses.
+ *
+ * The appropriate mapping table is selected based on the chip ID, and the
+ * `phy_addr_map` is populated with the correct addresses for each port. Any
+ * port with no PHY is assigned a `LAN937X_NO_PHY` marker.
+ *
+ * Return: 0 on success, error code on failure.
+ */
+int lan937x_create_phy_addr_map(struct ksz_device *dev, bool side_mdio)
+{
+ static const u8 *phy_addr_map;
+ u32 strap_val;
+ u8 offset = 0;
+ size_t size;
+ int ret, i;
+
+ if (!side_mdio) {
+ /* simple direct mapping */
+ for (i = 0; i < dev->info->port_cnt; i++)
+ dev->phy_addr_map[i] = i;
+
+ return 0;
+ }
+
+ ret = ksz_read32(dev, REG_SW_CFG_STRAP_VAL, &strap_val);
+ if (ret < 0)
+ return ret;
+
+ if (!(strap_val & SW_CASCADE_ID_CFG) && !(strap_val & SW_VPHY_ADD_CFG))
+ offset = 0;
+ else if (!(strap_val & SW_CASCADE_ID_CFG) && (strap_val & SW_VPHY_ADD_CFG))
+ offset = 7;
+ else if ((strap_val & SW_CASCADE_ID_CFG) && !(strap_val & SW_VPHY_ADD_CFG))
+ offset = 15;
+ else
+ offset = 22;
+
+ switch (dev->info->chip_id) {
+ case LAN9370_CHIP_ID:
+ phy_addr_map = lan9370_phy_addr;
+ size = ARRAY_SIZE(lan9370_phy_addr);
+ break;
+ case LAN9371_CHIP_ID:
+ phy_addr_map = lan9371_phy_addr;
+ size = ARRAY_SIZE(lan9371_phy_addr);
+ break;
+ case LAN9372_CHIP_ID:
+ phy_addr_map = lan9372_phy_addr;
+ size = ARRAY_SIZE(lan9372_phy_addr);
+ break;
+ case LAN9373_CHIP_ID:
+ phy_addr_map = lan9373_phy_addr;
+ size = ARRAY_SIZE(lan9373_phy_addr);
+ break;
+ case LAN9374_CHIP_ID:
+ phy_addr_map = lan9374_phy_addr;
+ size = ARRAY_SIZE(lan9374_phy_addr);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (size < dev->info->port_cnt)
+ return -EINVAL;
+
+ for (i = 0; i < dev->info->port_cnt; i++) {
+ if (phy_addr_map[i] == LAN937X_NO_PHY)
+ dev->phy_addr_map[i] = phy_addr_map[i];
+ else
+ dev->phy_addr_map[i] = phy_addr_map[i] + offset;
+ }
+
+ return 0;
+}
+
+/**
+ * lan937x_mdio_bus_preinit - Pre-initialize MDIO bus for accessing PHYs.
+ * @dev: Pointer to device structure.
+ * @side_mdio: Boolean indicating if the PHYs are accessed over a side MDIO bus.
+ *
+ * This function configures the LAN937x switch for PHY access either through
+ * SPI or the side MDIO bus, unlocking the necessary registers for each access
+ * mode.
+ *
+ * Operation Modes:
+ * 1. **SPI Access**: Enables SPI indirect access to address clock domain
+ * crossing issues when SPI is used for PHY access.
+ * 2. **MDIO Access**: Grants access to internal PHYs over the side MDIO bus,
+ * required when using the MDIO bus for PHY management.
+ *
+ * Return: 0 on success, error code on failure.
+ */
+int lan937x_mdio_bus_preinit(struct ksz_device *dev, bool side_mdio)
{
u16 data16;
int ret;
- /* Enable Phy access through SPI */
+ /* Unlock access to the PHYs, needed for SPI and side MDIO access */
ret = lan937x_cfg(dev, REG_GLOBAL_CTRL_0, SW_PHY_REG_BLOCK, false);
if (ret < 0)
- return ret;
+ goto print_error;
- ret = ksz_read16(dev, REG_VPHY_SPECIAL_CTRL__2, &data16);
- if (ret < 0)
- return ret;
+ if (side_mdio)
+ /* Allow access to internal PHYs over MDIO bus */
+ data16 = VPHY_MDIO_INTERNAL_ENABLE;
+ else
+ /* Enable SPI indirect access to address clock domain crossing
+ * issue
+ */
+ data16 = VPHY_SPI_INDIRECT_ENABLE;
- /* Allow SPI access */
- data16 |= VPHY_SPI_INDIRECT_ENABLE;
+ ret = ksz_rmw16(dev, REG_VPHY_SPECIAL_CTRL__2,
+ VPHY_SPI_INDIRECT_ENABLE | VPHY_MDIO_INTERNAL_ENABLE,
+ data16);
+
+print_error:
+ if (ret < 0)
+ dev_err(dev->dev, "failed to preinit the MDIO bus\n");
- return ksz_write16(dev, REG_VPHY_SPECIAL_CTRL__2, data16);
+ return ret;
}
static int lan937x_vphy_ind_addr_wr(struct ksz_device *dev, int addr, int reg)
struct ksz_device *dev = ds->priv;
int ret;
- /* enable Indirect Access from SPI to the VPHY registers */
- ret = lan937x_enable_spi_indirect_access(dev);
- if (ret < 0) {
- dev_err(dev->dev, "failed to enable spi indirect access");
- return ret;
- }
-
/* The VLAN aware is a global setting. Mixed vlan
* filterings are not supported.
*/
projects / linux-block.git / commitdiff