-BUCKn : 1-4.
Use standard regulator bindings for it ('regulator-off-in-suspend').
+ LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable
+ control. To turn this feature on this property must be added to the regulator
+ sub-node:
+ - maxim,ena-gpios : one GPIO specifier enable control (the gpio
+ flags are actually ignored and always
+ ACTIVE_HIGH is used)
Example:
regulator-always-on;
regulator-boot-on;
};
+
+ buck9_reg {
+ regulator-compatible = "BUCK9";
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1200000>;
+ maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+ };
}
Required properties:
-- compatible: "isl,isl9305" or "isl,isl9305h"
+- compatible: "isil,isl9305" or "isil,isl9305h"
- reg: I2C slave address, usually 0x68.
- regulators: A node that houses a sub-node for each regulator within the
device. Each sub-node is identified using the node's name, with valid
Example
pmic: isl9305@68 {
- compatible = "isl,isl9305";
+ compatible = "isil,isl9305";
reg = <0x68>;
VINDCD1-supply = <&system_power>;
Exynos5420/Exynos5800 SoCs to control various voltages.
It includes support for control of voltage and ramp speed.
+config REGULATOR_MAX77843
+ tristate "Maxim 77843 regulator"
+ depends on MFD_MAX77843
+ help
+ This driver controls a Maxim 77843 regulator.
+ The regulator include two 'SAFEOUT' for USB(Universal Serial Bus)
+ This is suitable for Exynos5433 SoC chips.
+
config REGULATOR_MC13XXX_CORE
tristate
obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o
obj-$(CONFIG_REGULATOR_MAX77693) += max77693.o
obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o
+obj-$(CONFIG_REGULATOR_MAX77843) += max77843.o
obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
#ifdef CONFIG_OF
static const struct of_device_id isl9305_dt_ids[] = {
- { .compatible = "isl,isl9305" },
- { .compatible = "isl,isl9305h" },
+ { .compatible = "isl,isl9305" }, /* for backward compat., don't use */
+ { .compatible = "isil,isl9305" },
+ { .compatible = "isl,isl9305h" }, /* for backward compat., don't use */
+ { .compatible = "isil,isl9305h" },
{},
};
#endif
struct device *dev;
enum lp872x_id chipid;
struct lp872x_platform_data *pdata;
- struct regulator_dev **regulators;
int num_regulators;
enum lp872x_dvs_state dvs_pin;
int dvs_gpio;
dev_err(lp->dev, "regulator register err");
return PTR_ERR(rdev);
}
-
- *(lp->regulators + i) = rdev;
}
return 0;
static int lp872x_probe(struct i2c_client *cl, const struct i2c_device_id *id)
{
struct lp872x *lp;
- int ret, size, num_regulators;
+ int ret;
const int lp872x_num_regulators[] = {
[LP8720] = LP8720_NUM_REGULATORS,
[LP8725] = LP8725_NUM_REGULATORS,
lp = devm_kzalloc(&cl->dev, sizeof(struct lp872x), GFP_KERNEL);
if (!lp)
- goto err_mem;
-
- num_regulators = lp872x_num_regulators[id->driver_data];
- size = sizeof(struct regulator_dev *) * num_regulators;
+ return -ENOMEM;
- lp->regulators = devm_kzalloc(&cl->dev, size, GFP_KERNEL);
- if (!lp->regulators)
- goto err_mem;
+ lp->num_regulators = lp872x_num_regulators[id->driver_data];
lp->regmap = devm_regmap_init_i2c(cl, &lp872x_regmap_config);
if (IS_ERR(lp->regmap)) {
ret = PTR_ERR(lp->regmap);
dev_err(&cl->dev, "regmap init i2c err: %d\n", ret);
- goto err_dev;
+ return ret;
}
lp->dev = &cl->dev;
lp->pdata = dev_get_platdata(&cl->dev);
lp->chipid = id->driver_data;
- lp->num_regulators = num_regulators;
i2c_set_clientdata(cl, lp);
ret = lp872x_config(lp);
if (ret)
- goto err_dev;
+ return ret;
return lp872x_regulator_register(lp);
-
-err_mem:
- return -ENOMEM;
-err_dev:
- return ret;
}
static const struct of_device_id lp872x_dt_ids[] = {
static const struct regulator_desc max14577_supported_regulators[] = {
[MAX14577_SAFEOUT] = {
.name = "SAFEOUT",
+ .of_match = of_match_ptr("SAFEOUT"),
+ .regulators_node = of_match_ptr("regulators"),
.id = MAX14577_SAFEOUT,
.ops = &max14577_safeout_ops,
.type = REGULATOR_VOLTAGE,
},
[MAX14577_CHARGER] = {
.name = "CHARGER",
+ .of_match = of_match_ptr("CHARGER"),
+ .regulators_node = of_match_ptr("regulators"),
.id = MAX14577_CHARGER,
.ops = &max14577_charger_ops,
.type = REGULATOR_CURRENT,
static const struct regulator_desc max77836_supported_regulators[] = {
[MAX14577_SAFEOUT] = {
.name = "SAFEOUT",
+ .of_match = of_match_ptr("SAFEOUT"),
+ .regulators_node = of_match_ptr("regulators"),
.id = MAX14577_SAFEOUT,
.ops = &max14577_safeout_ops,
.type = REGULATOR_VOLTAGE,
},
[MAX14577_CHARGER] = {
.name = "CHARGER",
+ .of_match = of_match_ptr("CHARGER"),
+ .regulators_node = of_match_ptr("regulators"),
.id = MAX14577_CHARGER,
.ops = &max14577_charger_ops,
.type = REGULATOR_CURRENT,
},
[MAX77836_LDO1] = {
.name = "LDO1",
+ .of_match = of_match_ptr("LDO1"),
+ .regulators_node = of_match_ptr("regulators"),
.id = MAX77836_LDO1,
.ops = &max77836_ldo_ops,
.type = REGULATOR_VOLTAGE,
},
[MAX77836_LDO2] = {
.name = "LDO2",
+ .of_match = of_match_ptr("LDO2"),
+ .regulators_node = of_match_ptr("regulators"),
.id = MAX77836_LDO2,
.ops = &max77836_ldo_ops,
.type = REGULATOR_VOLTAGE,
{ .name = "LDO2", },
};
-static int max14577_regulator_dt_parse_pdata(struct platform_device *pdev,
- enum maxim_device_type dev_type)
-{
- int ret;
- struct device_node *np;
- struct of_regulator_match *regulator_matches;
- unsigned int regulator_matches_size;
-
- np = of_get_child_by_name(pdev->dev.parent->of_node, "regulators");
- if (!np) {
- dev_err(&pdev->dev, "Failed to get child OF node for regulators\n");
- return -EINVAL;
- }
-
- switch (dev_type) {
- case MAXIM_DEVICE_TYPE_MAX77836:
- regulator_matches = max77836_regulator_matches;
- regulator_matches_size = ARRAY_SIZE(max77836_regulator_matches);
- break;
- case MAXIM_DEVICE_TYPE_MAX14577:
- default:
- regulator_matches = max14577_regulator_matches;
- regulator_matches_size = ARRAY_SIZE(max14577_regulator_matches);
- }
-
- ret = of_regulator_match(&pdev->dev, np, regulator_matches,
- regulator_matches_size);
- if (ret < 0)
- dev_err(&pdev->dev, "Error parsing regulator init data: %d\n", ret);
- else
- ret = 0;
-
- of_node_put(np);
-
- return ret;
-}
-
static inline struct regulator_init_data *match_init_data(int index,
enum maxim_device_type dev_type)
{
}
}
#else /* CONFIG_OF */
-static int max14577_regulator_dt_parse_pdata(struct platform_device *pdev,
- enum maxim_device_type dev_type)
-{
- return 0;
-}
static inline struct regulator_init_data *match_init_data(int index,
enum maxim_device_type dev_type)
{
{
struct max14577 *max14577 = dev_get_drvdata(pdev->dev.parent);
struct max14577_platform_data *pdata = dev_get_platdata(max14577->dev);
- int i, ret;
+ int i, ret = 0;
struct regulator_config config = {};
const struct regulator_desc *supported_regulators;
unsigned int supported_regulators_size;
enum maxim_device_type dev_type = max14577->dev_type;
- ret = max14577_regulator_dt_parse_pdata(pdev, dev_type);
- if (ret)
- return ret;
-
switch (dev_type) {
case MAXIM_DEVICE_TYPE_MAX77836:
supported_regulators = max77836_supported_regulators;
supported_regulators_size = ARRAY_SIZE(max14577_supported_regulators);
}
- config.dev = &pdev->dev;
+ config.dev = max14577->dev;
config.driver_data = max14577;
for (i = 0; i < supported_regulators_size; i++) {
#include <linux/bug.h>
#include <linux/err.h>
#include <linux/gpio.h>
+#include <linux/of_gpio.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
#define MAX77686_DVS_MINUV 600000
#define MAX77686_DVS_UVSTEP 12500
+/*
+ * Value for configuring buck[89] and LDO{20,21,22} as GPIO control.
+ * It is the same as 'off' for other regulators.
+ */
+#define MAX77686_GPIO_CONTROL 0x0
/*
* Values used for configuring LDOs and bucks.
* Forcing low power mode: LDO1, 3-5, 9, 13, 17-26
};
struct max77686_data {
+ u64 gpio_enabled:MAX77686_REGULATORS;
+
/* Array indexed by regulator id */
unsigned int opmode[MAX77686_REGULATORS];
};
}
}
+/*
+ * When regulator is configured for GPIO control then it
+ * replaces "normal" mode. Any change from low power mode to normal
+ * should actually change to GPIO control.
+ * Map normal mode to proper value for such regulators.
+ */
+static unsigned int max77686_map_normal_mode(struct max77686_data *max77686,
+ int id)
+{
+ switch (id) {
+ case MAX77686_BUCK8:
+ case MAX77686_BUCK9:
+ case MAX77686_LDO20 ... MAX77686_LDO22:
+ if (max77686->gpio_enabled & (1 << id))
+ return MAX77686_GPIO_CONTROL;
+ }
+
+ return MAX77686_NORMAL;
+}
+
/* Some BUCKs and LDOs supports Normal[ON/OFF] mode during suspend */
static int max77686_set_suspend_disable(struct regulator_dev *rdev)
{
val = MAX77686_LDO_LOWPOWER_PWRREQ;
break;
case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
- val = MAX77686_NORMAL;
+ val = max77686_map_normal_mode(max77686, id);
break;
default:
pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
{
unsigned int val;
struct max77686_data *max77686 = rdev_get_drvdata(rdev);
- int ret;
+ int ret, id = rdev_get_id(rdev);
switch (mode) {
case REGULATOR_MODE_STANDBY: /* switch off */
val = MAX77686_LDO_LOWPOWER_PWRREQ;
break;
case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
- val = MAX77686_NORMAL;
+ val = max77686_map_normal_mode(max77686, id);
break;
default:
pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
if (ret)
return ret;
- max77686->opmode[rdev_get_id(rdev)] = val;
+ max77686->opmode[id] = val;
return 0;
}
shift = max77686_get_opmode_shift(id);
if (max77686->opmode[id] == MAX77686_OFF_PWRREQ)
- max77686->opmode[id] = MAX77686_NORMAL;
+ max77686->opmode[id] = max77686_map_normal_mode(max77686, id);
return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
rdev->desc->enable_mask,
MAX77686_RAMP_RATE_MASK, ramp_value << 6);
}
+static int max77686_of_parse_cb(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ struct max77686_data *max77686 = config->driver_data;
+
+ switch (desc->id) {
+ case MAX77686_BUCK8:
+ case MAX77686_BUCK9:
+ case MAX77686_LDO20 ... MAX77686_LDO22:
+ config->ena_gpio = of_get_named_gpio(np,
+ "maxim,ena-gpios", 0);
+ config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
+ config->ena_gpio_initialized = true;
+ break;
+ default:
+ return 0;
+ }
+
+ if (gpio_is_valid(config->ena_gpio)) {
+ max77686->gpio_enabled |= (1 << desc->id);
+
+ return regmap_update_bits(config->regmap, desc->enable_reg,
+ desc->enable_mask,
+ MAX77686_GPIO_CONTROL);
+ }
+
+ return 0;
+}
+
static struct regulator_ops max77686_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
.name = "LDO"#num, \
.of_match = of_match_ptr("LDO"#num), \
.regulators_node = of_match_ptr("voltage-regulators"), \
+ .of_parse_cb = max77686_of_parse_cb, \
.id = MAX77686_LDO##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \
.name = "BUCK"#num, \
.of_match = of_match_ptr("BUCK"#num), \
.regulators_node = of_match_ptr("voltage-regulators"), \
+ .of_parse_cb = max77686_of_parse_cb, \
.id = MAX77686_BUCK##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \
--- /dev/null
+/*
+ * max77843.c - Regulator driver for the Maxim MAX77843
+ *
+ * Copyright (C) 2015 Samsung Electronics
+ * Author: Jaewon Kim <jaewon02.kim@samsung.com>
+ * Author: Beomho Seo <beomho.seo@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/max77843-private.h>
+#include <linux/regulator/of_regulator.h>
+
+enum max77843_regulator_type {
+ MAX77843_SAFEOUT1 = 0,
+ MAX77843_SAFEOUT2,
+ MAX77843_CHARGER,
+
+ MAX77843_NUM,
+};
+
+static const unsigned int max77843_safeout_voltage_table[] = {
+ 4850000,
+ 4900000,
+ 4950000,
+ 3300000,
+};
+
+static int max77843_reg_is_enabled(struct regulator_dev *rdev)
+{
+ struct regmap *regmap = rdev->regmap;
+ int ret;
+ unsigned int reg;
+
+ ret = regmap_read(regmap, rdev->desc->enable_reg, ®);
+ if (ret) {
+ dev_err(&rdev->dev, "Fialed to read charger register\n");
+ return ret;
+ }
+
+ return (reg & rdev->desc->enable_mask) == rdev->desc->enable_mask;
+}
+
+static int max77843_reg_get_current_limit(struct regulator_dev *rdev)
+{
+ struct regmap *regmap = rdev->regmap;
+ unsigned int chg_min_uA = rdev->constraints->min_uA;
+ unsigned int chg_max_uA = rdev->constraints->max_uA;
+ unsigned int val;
+ int ret;
+ unsigned int reg, sel;
+
+ ret = regmap_read(regmap, MAX77843_CHG_REG_CHG_CNFG_02, ®);
+ if (ret) {
+ dev_err(&rdev->dev, "Failed to read charger register\n");
+ return ret;
+ }
+
+ sel = reg & MAX77843_CHG_FAST_CHG_CURRENT_MASK;
+
+ if (sel < 0x03)
+ sel = 0;
+ else
+ sel -= 2;
+
+ val = chg_min_uA + MAX77843_CHG_FAST_CHG_CURRENT_STEP * sel;
+ if (val > chg_max_uA)
+ return -EINVAL;
+
+ return val;
+}
+
+static int max77843_reg_set_current_limit(struct regulator_dev *rdev,
+ int min_uA, int max_uA)
+{
+ struct regmap *regmap = rdev->regmap;
+ unsigned int chg_min_uA = rdev->constraints->min_uA;
+ int sel = 0;
+
+ while (chg_min_uA + MAX77843_CHG_FAST_CHG_CURRENT_STEP * sel < min_uA)
+ sel++;
+
+ if (chg_min_uA + MAX77843_CHG_FAST_CHG_CURRENT_STEP * sel > max_uA)
+ return -EINVAL;
+
+ sel += 2;
+
+ return regmap_write(regmap, MAX77843_CHG_REG_CHG_CNFG_02, sel);
+}
+
+static struct regulator_ops max77843_charger_ops = {
+ .is_enabled = max77843_reg_is_enabled,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_current_limit = max77843_reg_get_current_limit,
+ .set_current_limit = max77843_reg_set_current_limit,
+};
+
+static struct regulator_ops max77843_regulator_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+};
+
+static const struct regulator_desc max77843_supported_regulators[] = {
+ [MAX77843_SAFEOUT1] = {
+ .name = "SAFEOUT1",
+ .id = MAX77843_SAFEOUT1,
+ .ops = &max77843_regulator_ops,
+ .of_match = of_match_ptr("SAFEOUT1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = ARRAY_SIZE(max77843_safeout_voltage_table),
+ .volt_table = max77843_safeout_voltage_table,
+ .enable_reg = MAX77843_SYS_REG_SAFEOUTCTRL,
+ .enable_mask = MAX77843_REG_SAFEOUTCTRL_ENSAFEOUT1,
+ .vsel_reg = MAX77843_SYS_REG_SAFEOUTCTRL,
+ .vsel_mask = MAX77843_REG_SAFEOUTCTRL_SAFEOUT1_MASK,
+ },
+ [MAX77843_SAFEOUT2] = {
+ .name = "SAFEOUT2",
+ .id = MAX77843_SAFEOUT2,
+ .ops = &max77843_regulator_ops,
+ .of_match = of_match_ptr("SAFEOUT2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = ARRAY_SIZE(max77843_safeout_voltage_table),
+ .volt_table = max77843_safeout_voltage_table,
+ .enable_reg = MAX77843_SYS_REG_SAFEOUTCTRL,
+ .enable_mask = MAX77843_REG_SAFEOUTCTRL_ENSAFEOUT2,
+ .vsel_reg = MAX77843_SYS_REG_SAFEOUTCTRL,
+ .vsel_mask = MAX77843_REG_SAFEOUTCTRL_SAFEOUT2_MASK,
+ },
+ [MAX77843_CHARGER] = {
+ .name = "CHARGER",
+ .id = MAX77843_CHARGER,
+ .ops = &max77843_charger_ops,
+ .of_match = of_match_ptr("CHARGER"),
+ .regulators_node = of_match_ptr("regulators"),
+ .type = REGULATOR_CURRENT,
+ .owner = THIS_MODULE,
+ .enable_reg = MAX77843_CHG_REG_CHG_CNFG_00,
+ .enable_mask = MAX77843_CHG_MASK,
+ },
+};
+
+static struct regmap *max77843_get_regmap(struct max77843 *max77843, int reg_id)
+{
+ switch (reg_id) {
+ case MAX77843_SAFEOUT1:
+ case MAX77843_SAFEOUT2:
+ return max77843->regmap;
+ case MAX77843_CHARGER:
+ return max77843->regmap_chg;
+ default:
+ return max77843->regmap;
+ }
+}
+
+static int max77843_regulator_probe(struct platform_device *pdev)
+{
+ struct max77843 *max77843 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = {};
+ int i;
+
+ config.dev = max77843->dev;
+ config.driver_data = max77843;
+
+ for (i = 0; i < ARRAY_SIZE(max77843_supported_regulators); i++) {
+ struct regulator_dev *regulator;
+
+ config.regmap = max77843_get_regmap(max77843,
+ max77843_supported_regulators[i].id);
+
+ regulator = devm_regulator_register(&pdev->dev,
+ &max77843_supported_regulators[i], &config);
+ if (IS_ERR(regulator)) {
+ dev_err(&pdev->dev,
+ "Failed to regiser regulator-%d\n", i);
+ return PTR_ERR(regulator);
+ }
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id max77843_regulator_id[] = {
+ { "max77843-regulator", },
+ { /* sentinel */ },
+};
+
+static struct platform_driver max77843_regulator_driver = {
+ .driver = {
+ .name = "max77843-regulator",
+ },
+ .probe = max77843_regulator_probe,
+ .id_table = max77843_regulator_id,
+};
+
+static int __init max77843_regulator_init(void)
+{
+ return platform_driver_register(&max77843_regulator_driver);
+}
+subsys_initcall(max77843_regulator_init);
+
+static void __exit max77843_regulator_exit(void)
+{
+ platform_driver_unregister(&max77843_regulator_driver);
+}
+module_exit(max77843_regulator_exit);
+
+MODULE_AUTHOR("Jaewon Kim <jaewon02.kim@samsung.com>");
+MODULE_AUTHOR("Beomho Seo <beomho.seo@samsung.com>");
+MODULE_DESCRIPTION("Maxim MAX77843 regulator driver");
+MODULE_LICENSE("GPL");
projects / linux-2.6-block.git / commitdiff