* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: Remove overly verbose "switch to high res mode" message
Kernel Version: 2.6.30
Contact: iss_storagedev@hp.com
Description: A symbolic link to /sys/block/cciss!cXdY
+
+Where: /sys/bus/pci/devices/<dev>/ccissX/rescan
+Date: August 2009
+Kernel Version: 2.6.31
+Contact: iss_storagedev@hp.com
+Description: Kicks of a rescan of the controller to discover logical
+ drive topology changes.
+
+Where: /sys/bus/pci/devices/<dev>/ccissX/cXdY/lunid
+Date: August 2009
+Kernel Version: 2.6.31
+Contact: iss_storagedev@hp.com
+Description: Displays the 8-byte LUN ID used to address logical
+ drive Y of controller X.
+
+Where: /sys/bus/pci/devices/<dev>/ccissX/cXdY/raid_level
+Date: August 2009
+Kernel Version: 2.6.31
+Contact: iss_storagedev@hp.com
+Description: Displays the RAID level of logical drive Y of
+ controller X.
+
+Where: /sys/bus/pci/devices/<dev>/ccissX/cXdY/usage_count
+Date: August 2009
+Kernel Version: 2.6.31
+Contact: iss_storagedev@hp.com
+Description: Displays the usage count (number of opens) of logical drive Y
+ of controller X.
When sending patches to Linus, always follow step #7.
Large changes are not appropriate for mailing lists, and some
-maintainers. If your patch, uncompressed, exceeds 40 kB in size,
+maintainers. If your patch, uncompressed, exceeds 300 kB in size,
it is preferred that you store your patch on an Internet-accessible
server, and provide instead a URL (link) pointing to your patch.
--- /dev/null
+ARM TCM (Tightly-Coupled Memory) handling in Linux
+----
+Written by Linus Walleij <linus.walleij@stericsson.com>
+
+Some ARM SoC:s have a so-called TCM (Tightly-Coupled Memory).
+This is usually just a few (4-64) KiB of RAM inside the ARM
+processor.
+
+Due to being embedded inside the CPU The TCM has a
+Harvard-architecture, so there is an ITCM (instruction TCM)
+and a DTCM (data TCM). The DTCM can not contain any
+instructions, but the ITCM can actually contain data.
+The size of DTCM or ITCM is minimum 4KiB so the typical
+minimum configuration is 4KiB ITCM and 4KiB DTCM.
+
+ARM CPU:s have special registers to read out status, physical
+location and size of TCM memories. arch/arm/include/asm/cputype.h
+defines a CPUID_TCM register that you can read out from the
+system control coprocessor. Documentation from ARM can be found
+at http://infocenter.arm.com, search for "TCM Status Register"
+to see documents for all CPUs. Reading this register you can
+determine if ITCM (bit 0) and/or DTCM (bit 16) is present in the
+machine.
+
+There is further a TCM region register (search for "TCM Region
+Registers" at the ARM site) that can report and modify the location
+size of TCM memories at runtime. This is used to read out and modify
+TCM location and size. Notice that this is not a MMU table: you
+actually move the physical location of the TCM around. At the
+place you put it, it will mask any underlying RAM from the
+CPU so it is usually wise not to overlap any physical RAM with
+the TCM.
+
+The TCM memory can then be remapped to another address again using
+the MMU, but notice that the TCM if often used in situations where
+the MMU is turned off. To avoid confusion the current Linux
+implementation will map the TCM 1 to 1 from physical to virtual
+memory in the location specified by the machine.
+
+TCM is used for a few things:
+
+- FIQ and other interrupt handlers that need deterministic
+ timing and cannot wait for cache misses.
+
+- Idle loops where all external RAM is set to self-refresh
+ retention mode, so only on-chip RAM is accessible by
+ the CPU and then we hang inside ITCM waiting for an
+ interrupt.
+
+- Other operations which implies shutting off or reconfiguring
+ the external RAM controller.
+
+There is an interface for using TCM on the ARM architecture
+in <asm/tcm.h>. Using this interface it is possible to:
+
+- Define the physical address and size of ITCM and DTCM.
+
+- Tag functions to be compiled into ITCM.
+
+- Tag data and constants to be allocated to DTCM and ITCM.
+
+- Have the remaining TCM RAM added to a special
+ allocation pool with gen_pool_create() and gen_pool_add()
+ and provice tcm_alloc() and tcm_free() for this
+ memory. Such a heap is great for things like saving
+ device state when shutting off device power domains.
+
+A machine that has TCM memory shall select HAVE_TCM in
+arch/arm/Kconfig for itself, and then the
+rest of the functionality will depend on the physical
+location and size of ITCM and DTCM to be defined in
+mach/memory.h for the machine. Code that needs to use
+TCM shall #include <asm/tcm.h> If the TCM is not located
+at the place given in memory.h it will be moved using
+the TCM Region registers.
+
+Functions to go into itcm can be tagged like this:
+int __tcmfunc foo(int bar);
+
+Variables to go into dtcm can be tagged like this:
+int __tcmdata foo;
+
+Constants can be tagged like this:
+int __tcmconst foo;
+
+To put assembler into TCM just use
+.section ".tcm.text" or .section ".tcm.data"
+respectively.
+
+Example code:
+
+#include <asm/tcm.h>
+
+/* Uninitialized data */
+static u32 __tcmdata tcmvar;
+/* Initialized data */
+static u32 __tcmdata tcmassigned = 0x2BADBABEU;
+/* Constant */
+static const u32 __tcmconst tcmconst = 0xCAFEBABEU;
+
+static void __tcmlocalfunc tcm_to_tcm(void)
+{
+ int i;
+ for (i = 0; i < 100; i++)
+ tcmvar ++;
+}
+
+static void __tcmfunc hello_tcm(void)
+{
+ /* Some abstract code that runs in ITCM */
+ int i;
+ for (i = 0; i < 100; i++) {
+ tcmvar ++;
+ }
+ tcm_to_tcm();
+}
+
+static void __init test_tcm(void)
+{
+ u32 *tcmem;
+ int i;
+
+ hello_tcm();
+ printk("Hello TCM executed from ITCM RAM\n");
+
+ printk("TCM variable from testrun: %u @ %p\n", tcmvar, &tcmvar);
+ tcmvar = 0xDEADBEEFU;
+ printk("TCM variable: 0x%x @ %p\n", tcmvar, &tcmvar);
+
+ printk("TCM assigned variable: 0x%x @ %p\n", tcmassigned, &tcmassigned);
+
+ printk("TCM constant: 0x%x @ %p\n", tcmconst, &tcmconst);
+
+ /* Allocate some TCM memory from the pool */
+ tcmem = tcm_alloc(20);
+ if (tcmem) {
+ printk("TCM Allocated 20 bytes of TCM @ %p\n", tcmem);
+ tcmem[0] = 0xDEADBEEFU;
+ tcmem[1] = 0x2BADBABEU;
+ tcmem[2] = 0xCAFEBABEU;
+ tcmem[3] = 0xDEADBEEFU;
+ tcmem[4] = 0x2BADBABEU;
+ for (i = 0; i < 5; i++)
+ printk("TCM tcmem[%d] = %08x\n", i, tcmem[i]);
+ tcm_free(tcmem, 20);
+ }
+}
*/
#include <stdio.h>
-#include <string.h>
#define EXAMPLES 6
# echo 0 > tasks
+2.3 Mounting hierarchies by name
+--------------------------------
+
+Passing the name=<x> option when mounting a cgroups hierarchy
+associates the given name with the hierarchy. This can be used when
+mounting a pre-existing hierarchy, in order to refer to it by name
+rather than by its set of active subsystems. Each hierarchy is either
+nameless, or has a unique name.
+
+The name should match [\w.-]+
+
+When passing a name=<x> option for a new hierarchy, you need to
+specify subsystems manually; the legacy behaviour of mounting all
+subsystems when none are explicitly specified is not supported when
+you give a subsystem a name.
+
+The name of the subsystem appears as part of the hierarchy description
+in /proc/mounts and /proc/<pid>/cgroups.
+
+
3. Kernel API
=============
called multiple times against a cgroup.
int can_attach(struct cgroup_subsys *ss, struct cgroup *cgrp,
- struct task_struct *task)
+ struct task_struct *task, bool threadgroup)
(cgroup_mutex held by caller)
Called prior to moving a task into a cgroup; if the subsystem
task is passed, then a successful result indicates that *any*
unspecified task can be moved into the cgroup. Note that this isn't
called on a fork. If this method returns 0 (success) then this should
-remain valid while the caller holds cgroup_mutex.
+remain valid while the caller holds cgroup_mutex. If threadgroup is
+true, then a successful result indicates that all threads in the given
+thread's threadgroup can be moved together.
void attach(struct cgroup_subsys *ss, struct cgroup *cgrp,
- struct cgroup *old_cgrp, struct task_struct *task)
+ struct cgroup *old_cgrp, struct task_struct *task,
+ bool threadgroup)
(cgroup_mutex held by caller)
Called after the task has been attached to the cgroup, to allow any
post-attachment activity that requires memory allocations or blocking.
+If threadgroup is true, the subsystem should take care of all threads
+in the specified thread's threadgroup. Currently does not support any
+subsystem that might need the old_cgrp for every thread in the group.
void fork(struct cgroup_subsy *ss, struct task_struct *task)
pages that are selected for reclaiming come from the per cgroup LRU
list.
+NOTE: Reclaim does not work for the root cgroup, since we cannot set any
+limits on the root cgroup.
+
2. Locking
The memory controller uses the following hierarchy
NOTE: We can use a suffix (k, K, m, M, g or G) to indicate values in kilo,
mega or gigabytes.
NOTE: We can write "-1" to reset the *.limit_in_bytes(unlimited).
+NOTE: We cannot set limits on the root cgroup any more.
# cat /cgroups/0/memory.limit_in_bytes
4194304
NOTE2: This feature can be enabled/disabled per subtree.
-7. TODO
+7. Soft limits
+
+Soft limits allow for greater sharing of memory. The idea behind soft limits
+is to allow control groups to use as much of the memory as needed, provided
+
+a. There is no memory contention
+b. They do not exceed their hard limit
+
+When the system detects memory contention or low memory control groups
+are pushed back to their soft limits. If the soft limit of each control
+group is very high, they are pushed back as much as possible to make
+sure that one control group does not starve the others of memory.
+
+Please note that soft limits is a best effort feature, it comes with
+no guarantees, but it does its best to make sure that when memory is
+heavily contended for, memory is allocated based on the soft limit
+hints/setup. Currently soft limit based reclaim is setup such that
+it gets invoked from balance_pgdat (kswapd).
+
+7.1 Interface
+
+Soft limits can be setup by using the following commands (in this example we
+assume a soft limit of 256 megabytes)
+
+# echo 256M > memory.soft_limit_in_bytes
+
+If we want to change this to 1G, we can at any time use
+
+# echo 1G > memory.soft_limit_in_bytes
+
+NOTE1: Soft limits take effect over a long period of time, since they involve
+ reclaiming memory for balancing between memory cgroups
+NOTE2: It is recommended to set the soft limit always below the hard limit,
+ otherwise the hard limit will take precedence.
+
+8. TODO
1. Add support for accounting huge pages (as a separate controller)
2. Make per-cgroup scanner reclaim not-shared pages first
static struct sock *nls;
static struct timer_list cn_test_timer;
-static void cn_test_callback(struct cn_msg *msg)
+static void cn_test_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
pr_info("%s: %lu: idx=%x, val=%x, seq=%u, ack=%u, len=%d: %s.\n",
__func__, jiffies, msg->id.idx, msg->id.val,
netlink based networking for inter-process communication in a significantly
easier way:
-int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
+int cn_add_callback(struct cb_id *id, char *name, void (*callback) (struct cn_msg *, struct netlink_skb_parms *));
void cn_netlink_send(struct cn_msg *msg, u32 __group, int gfp_mask);
struct cb_id
Connector interfaces.
/*****************************************/
-int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
+int cn_add_callback(struct cb_id *id, char *name, void (*callback) (struct cn_msg *, struct netlink_skb_parms *));
Registers new callback with connector core.
struct cb_id *id - unique connector's user identifier.
It must be registered in connector.h for legal in-kernel users.
char *name - connector's callback symbolic name.
- void (*callback) (void *) - connector's callback.
- Argument must be dereferenced to struct cn_msg *.
+ void (*callback) (struct cn..) - connector's callback.
+ cn_msg and the sender's credentials
void cn_del_callback(struct cb_id *id);
3.1 General format of the API:
struct dma_async_tx_descriptor *
-async_<operation>(<op specific parameters>,
- enum async_tx_flags flags,
- struct dma_async_tx_descriptor *dependency,
- dma_async_tx_callback callback_routine,
- void *callback_parameter);
+async_<operation>(<op specific parameters>, struct async_submit ctl *submit)
3.2 Supported operations:
-memcpy - memory copy between a source and a destination buffer
-memset - fill a destination buffer with a byte value
-xor - xor a series of source buffers and write the result to a
- destination buffer
-xor_zero_sum - xor a series of source buffers and set a flag if the
- result is zero. The implementation attempts to prevent
- writes to memory
+memcpy - memory copy between a source and a destination buffer
+memset - fill a destination buffer with a byte value
+xor - xor a series of source buffers and write the result to a
+ destination buffer
+xor_val - xor a series of source buffers and set a flag if the
+ result is zero. The implementation attempts to prevent
+ writes to memory
+pq - generate the p+q (raid6 syndrome) from a series of source buffers
+pq_val - validate that a p and or q buffer are in sync with a given series of
+ sources
+datap - (raid6_datap_recov) recover a raid6 data block and the p block
+ from the given sources
+2data - (raid6_2data_recov) recover 2 raid6 data blocks from the given
+ sources
3.3 Descriptor management:
The return value is non-NULL and points to a 'descriptor' when the operation
recycle (or free) the descriptor. A descriptor can be acked by one of the
following methods:
1/ setting the ASYNC_TX_ACK flag if no child operations are to be submitted
-2/ setting the ASYNC_TX_DEP_ACK flag to acknowledge the parent
- descriptor of a new operation.
+2/ submitting an unacknowledged descriptor as a dependency to another
+ async_tx call will implicitly set the acknowledged state.
3/ calling async_tx_ack() on the descriptor.
3.4 When does the operation execute?
Perform a xor->copy->xor operation where each operation depends on the
result from the previous operation:
-void complete_xor_copy_xor(void *param)
+void callback(void *param)
{
- printk("complete\n");
+ struct completion *cmp = param;
+
+ complete(cmp);
}
-int run_xor_copy_xor(struct page **xor_srcs,
- int xor_src_cnt,
- struct page *xor_dest,
- size_t xor_len,
- struct page *copy_src,
- struct page *copy_dest,
- size_t copy_len)
+void run_xor_copy_xor(struct page **xor_srcs,
+ int xor_src_cnt,
+ struct page *xor_dest,
+ size_t xor_len,
+ struct page *copy_src,
+ struct page *copy_dest,
+ size_t copy_len)
{
struct dma_async_tx_descriptor *tx;
+ addr_conv_t addr_conv[xor_src_cnt];
+ struct async_submit_ctl submit;
+ addr_conv_t addr_conv[NDISKS];
+ struct completion cmp;
+
+ init_async_submit(&submit, ASYNC_TX_XOR_DROP_DST, NULL, NULL, NULL,
+ addr_conv);
+ tx = async_xor(xor_dest, xor_srcs, 0, xor_src_cnt, xor_len, &submit)
- tx = async_xor(xor_dest, xor_srcs, 0, xor_src_cnt, xor_len,
- ASYNC_TX_XOR_DROP_DST, NULL, NULL, NULL);
- tx = async_memcpy(copy_dest, copy_src, 0, 0, copy_len,
- ASYNC_TX_DEP_ACK, tx, NULL, NULL);
- tx = async_xor(xor_dest, xor_srcs, 0, xor_src_cnt, xor_len,
- ASYNC_TX_XOR_DROP_DST | ASYNC_TX_DEP_ACK | ASYNC_TX_ACK,
- tx, complete_xor_copy_xor, NULL);
+ submit->depend_tx = tx;
+ tx = async_memcpy(copy_dest, copy_src, 0, 0, copy_len, &submit);
+
+ init_completion(&cmp);
+ init_async_submit(&submit, ASYNC_TX_XOR_DROP_DST | ASYNC_TX_ACK, tx,
+ callback, &cmp, addr_conv);
+ tx = async_xor(xor_dest, xor_srcs, 0, xor_src_cnt, xor_len, &submit);
async_tx_issue_pending_all();
+
+ wait_for_completion(&cmp);
}
See include/linux/async_tx.h for more information on the flags. See the
to use for allocation size and alignment. For RAID5/6
systems this should be the number of data
disks * RAID chunk size in file system blocks.
-delalloc (*) Deferring block allocation until write-out time.
-nodelalloc Disable delayed allocation. Blocks are allocation
- when data is copied from user to page cache.
+
+delalloc (*) Defer block allocation until just before ext4
+ writes out the block(s) in question. This
+ allows ext4 to better allocation decisions
+ more efficiently.
+nodelalloc Disable delayed allocation. Blocks are allocated
+ when the data is copied from userspace to the
+ page cache, either via the write(2) system call
+ or when an mmap'ed page which was previously
+ unallocated is written for the first time.
max_batch_time=usec Maximum amount of time ext4 should wait for
additional filesystem operations to be batch
..............................................................................
File Content
mb_groups details of multiblock allocator buddy cache of free blocks
- mb_history multiblock allocation history
..............................................................................
Contents:
1) Overview
2) Features
- 3) smount command
+ 3) Setting mount states
4) Use-case
5) Detailed semantics
6) Quiz
Here is an example:
- Lets say /mnt has a mount that is shared.
+ Let's say /mnt has a mount that is shared.
mount --make-shared /mnt
- note: mount command does not yet support the --make-shared flag.
- I have included a small C program which does the same by executing
- 'smount /mnt shared'
+ Note: mount(8) command now supports the --make-shared flag,
+ so the sample 'smount' program is no longer needed and has been
+ removed.
- #mount --bind /mnt /tmp
+ # mount --bind /mnt /tmp
The above command replicates the mount at /mnt to the mountpoint /tmp
and the contents of both the mounts remain identical.
#ls /tmp
a b c
- Now lets say we mount a device at /tmp/a
- #mount /dev/sd0 /tmp/a
+ Now let's say we mount a device at /tmp/a
+ # mount /dev/sd0 /tmp/a
#ls /tmp/a
t1 t2 t2
Here is an example:
- Lets say /mnt has a mount which is shared.
- #mount --make-shared /mnt
+ Let's say /mnt has a mount which is shared.
+ # mount --make-shared /mnt
- Lets bind mount /mnt to /tmp
- #mount --bind /mnt /tmp
+ Let's bind mount /mnt to /tmp
+ # mount --bind /mnt /tmp
the new mount at /tmp becomes a shared mount and it is a replica of
the mount at /mnt.
- Now lets make the mount at /tmp; a slave of /mnt
- #mount --make-slave /tmp
- [or smount /tmp slave]
+ Now let's make the mount at /tmp; a slave of /mnt
+ # mount --make-slave /tmp
- lets mount /dev/sd0 on /mnt/a
- #mount /dev/sd0 /mnt/a
+ let's mount /dev/sd0 on /mnt/a
+ # mount /dev/sd0 /mnt/a
#ls /mnt/a
t1 t2 t3
Note the mount event has propagated to the mount at /tmp
- However lets see what happens if we mount something on the mount at /tmp
+ However let's see what happens if we mount something on the mount at /tmp
- #mount /dev/sd1 /tmp/b
+ # mount /dev/sd1 /tmp/b
#ls /tmp/b
s1 s2 s3
2d) A unbindable mount is a unbindable private mount
- lets say we have a mount at /mnt and we make is unbindable
+ let's say we have a mount at /mnt and we make is unbindable
- #mount --make-unbindable /mnt
- [ smount /mnt unbindable ]
+ # mount --make-unbindable /mnt
- Lets try to bind mount this mount somewhere else.
+ Let's try to bind mount this mount somewhere else.
# mount --bind /mnt /tmp
mount: wrong fs type, bad option, bad superblock on /mnt,
or too many mounted file systems
Binding a unbindable mount is a invalid operation.
-3) smount command
+3) Setting mount states
- Currently the mount command is not aware of shared subtree features.
- Work is in progress to add the support in mount ( util-linux package ).
- Till then use the following program.
+ The mount command (util-linux package) can be used to set mount
+ states:
- ------------------------------------------------------------------------
- //
- //this code was developed my Miklos Szeredi <miklos@szeredi.hu>
- //and modified by Ram Pai <linuxram@us.ibm.com>
- // sample usage:
- // smount /tmp shared
- //
- #include <stdio.h>
- #include <stdlib.h>
- #include <unistd.h>
- #include <string.h>
- #include <sys/mount.h>
- #include <sys/fsuid.h>
-
- #ifndef MS_REC
- #define MS_REC 0x4000 /* 16384: Recursive loopback */
- #endif
-
- #ifndef MS_SHARED
- #define MS_SHARED 1<<20 /* Shared */
- #endif
-
- #ifndef MS_PRIVATE
- #define MS_PRIVATE 1<<18 /* Private */
- #endif
-
- #ifndef MS_SLAVE
- #define MS_SLAVE 1<<19 /* Slave */
- #endif
-
- #ifndef MS_UNBINDABLE
- #define MS_UNBINDABLE 1<<17 /* Unbindable */
- #endif
-
- int main(int argc, char *argv[])
- {
- int type;
- if(argc != 3) {
- fprintf(stderr, "usage: %s dir "
- "<rshared|rslave|rprivate|runbindable|shared|slave"
- "|private|unbindable>\n" , argv[0]);
- return 1;
- }
-
- fprintf(stdout, "%s %s %s\n", argv[0], argv[1], argv[2]);
-
- if (strcmp(argv[2],"rshared")==0)
- type=(MS_SHARED|MS_REC);
- else if (strcmp(argv[2],"rslave")==0)
- type=(MS_SLAVE|MS_REC);
- else if (strcmp(argv[2],"rprivate")==0)
- type=(MS_PRIVATE|MS_REC);
- else if (strcmp(argv[2],"runbindable")==0)
- type=(MS_UNBINDABLE|MS_REC);
- else if (strcmp(argv[2],"shared")==0)
- type=MS_SHARED;
- else if (strcmp(argv[2],"slave")==0)
- type=MS_SLAVE;
- else if (strcmp(argv[2],"private")==0)
- type=MS_PRIVATE;
- else if (strcmp(argv[2],"unbindable")==0)
- type=MS_UNBINDABLE;
- else {
- fprintf(stderr, "invalid operation: %s\n", argv[2]);
- return 1;
- }
- setfsuid(getuid());
-
- if(mount("", argv[1], "dontcare", type, "") == -1) {
- perror("mount");
- return 1;
- }
- return 0;
- }
- -----------------------------------------------------------------------
-
- Copy the above code snippet into smount.c
- gcc -o smount smount.c
-
-
- (i) To mark all the mounts under /mnt as shared execute the following
- command:
-
- smount /mnt rshared
- the corresponding syntax planned for mount command is
- mount --make-rshared /mnt
-
- just to mark a mount /mnt as shared, execute the following
- command:
- smount /mnt shared
- the corresponding syntax planned for mount command is
- mount --make-shared /mnt
-
- (ii) To mark all the shared mounts under /mnt as slave execute the
- following
-
- command:
- smount /mnt rslave
- the corresponding syntax planned for mount command is
- mount --make-rslave /mnt
-
- just to mark a mount /mnt as slave, execute the following
- command:
- smount /mnt slave
- the corresponding syntax planned for mount command is
- mount --make-slave /mnt
-
- (iii) To mark all the mounts under /mnt as private execute the
- following command:
-
- smount /mnt rprivate
- the corresponding syntax planned for mount command is
- mount --make-rprivate /mnt
-
- just to mark a mount /mnt as private, execute the following
- command:
- smount /mnt private
- the corresponding syntax planned for mount command is
- mount --make-private /mnt
-
- NOTE: by default all the mounts are created as private. But if
- you want to change some shared/slave/unbindable mount as
- private at a later point in time, this command can help.
-
- (iv) To mark all the mounts under /mnt as unbindable execute the
- following
-
- command:
- smount /mnt runbindable
- the corresponding syntax planned for mount command is
- mount --make-runbindable /mnt
-
- just to mark a mount /mnt as unbindable, execute the following
- command:
- smount /mnt unbindable
- the corresponding syntax planned for mount command is
- mount --make-unbindable /mnt
+ mount --make-shared mountpoint
+ mount --make-slave mountpoint
+ mount --make-private mountpoint
+ mount --make-unbindable mountpoint
4) Use cases
mount --rbind / /view/v3
mount --rbind / /view/v4
- and if /usr has a versioning filesystem mounted, than that
+ and if /usr has a versioning filesystem mounted, then that
mount appears at /view/v1/usr, /view/v2/usr, /view/v3/usr and
/view/v4/usr too
For example:
mount --make-shared /mnt
- mount --bin /mnt /tmp
+ mount --bind /mnt /tmp
The mount at /mnt and that at /tmp are both shared and belong
to the same peer group. Anything mounted or unmounted under
then the subtree under the unbindable mount is pruned in the new
location.
- eg: lets say we have the following mount tree.
+ eg: let's say we have the following mount tree.
A
/ \
/ \ / \
D E F G
- Lets say all the mount except the mount C in the tree are
+ Let's say all the mount except the mount C in the tree are
of a type other than unbindable.
If this tree is rbound to say Z
'b' on mounts that receive propagation from mount 'B' and does not have
sub-mounts within them are unmounted.
- Example: Lets say 'B1', 'B2', 'B3' are shared mounts that propagate to
+ Example: Let's say 'B1', 'B2', 'B3' are shared mounts that propagate to
each other.
- lets say 'A1', 'A2', 'A3' are first mounted at dentry 'b' on mount
+ let's say 'A1', 'A2', 'A3' are first mounted at dentry 'b' on mount
'B1', 'B2' and 'B3' respectively.
- lets say 'C1', 'C2', 'C3' are next mounted at the same dentry 'b' on
+ let's say 'C1', 'C2', 'C3' are next mounted at the same dentry 'b' on
mount 'B1', 'B2' and 'B3' respectively.
if 'C1' is unmounted, all the mounts that are most-recently-mounted on
A cloned namespace contains all the mounts as that of the parent
namespace.
- Lets say 'A' and 'B' are the corresponding mounts in the parent and the
+ Let's say 'A' and 'B' are the corresponding mounts in the parent and the
child namespace.
If 'A' is shared, then 'B' is also shared and 'A' and 'B' propagate to
mount --make-slave /mnt
At this point we have the first mount at /tmp and
- its root dentry is 1. Lets call this mount 'A'
+ its root dentry is 1. Let's call this mount 'A'
And then we have a second mount at /tmp1 with root
- dentry 2. Lets call this mount 'B'
+ dentry 2. Let's call this mount 'B'
Next we have a third mount at /mnt with root dentry
- mnt. Lets call this mount 'C'
+ mnt. Let's call this mount 'C'
'B' is the slave of 'A' and 'C' is a slave of 'B'
A -> B -> C
Q3 Why is unbindable mount needed?
- Lets say we want to replicate the mount tree at multiple
+ Let's say we want to replicate the mount tree at multiple
locations within the same subtree.
if one rbind mounts a tree within the same subtree 'n' times
mounts. Here is a example.
step 1:
- lets say the root tree has just two directories with
+ let's say the root tree has just two directories with
one vfsmount.
root
/ \
Unclonable mounts come in handy here.
step 1:
- lets say the root tree has just two directories with
+ let's say the root tree has just two directories with
one vfsmount.
root
/ \
winnt: emulate the Windows NT rule for display/create.
mixed: emulate the Windows NT rule for display,
emulate the Windows 95 rule for create.
- Default setting is `lower'.
+ Default setting is `mixed'.
tz=UTC -- Interpret timestamps as UTC rather than local time.
This option disables the conversion of timestamps
/* migrate the contents of a page to the specified target */
int (*migratepage) (struct page *, struct page *);
int (*launder_page) (struct page *);
+ int (*error_remove_page) (struct mapping *mapping, struct page *page);
};
writepage: called by the VM to write a dirty page to backing store.
prevent redirtying the page, it is kept locked during the whole
operation.
+ error_remove_page: normally set to generic_error_remove_page if truncation
+ is ok for this address space. Used for memory failure handling.
+ Setting this implies you deal with pages going away under you,
+ unless you have them locked or reference counts increased.
+
+
The File Object
===============
-----------
This driver does not probe for LTC4215 devices, due to the fact that some
-of the possible addresses are unfriendly to probing. You will need to use
-the "force" parameter to tell the driver where to find the device.
+of the possible addresses are unfriendly to probing. You will have to
+instantiate the devices explicitly.
Example: the following will load the driver for an LTC4215 at address 0x44
on I2C bus #0:
-$ modprobe ltc4215 force=0,0x44
+$ modprobe ltc4215
+$ echo ltc4215 0x44 > /sys/bus/i2c/devices/i2c-0/new_device
Sysfs entries
-----------
This driver does not probe for LTC4245 devices, due to the fact that some
-of the possible addresses are unfriendly to probing. You will need to use
-the "force" parameter to tell the driver where to find the device.
+of the possible addresses are unfriendly to probing. You will have to
+instantiate the devices explicitly.
Example: the following will load the driver for an LTC4245 at address 0x23
on I2C bus #1:
-$ modprobe ltc4245 force=1,0x23
+$ modprobe ltc4245
+$ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device
Sysfs entries
+++ /dev/null
-Kernel driver eeprom
-====================
-
-Supported chips:
- * Any EEPROM chip in the designated address range
- Prefix: 'eeprom'
- Addresses scanned: I2C 0x50 - 0x57
- Datasheets: Publicly available from:
- Atmel (www.atmel.com),
- Catalyst (www.catsemi.com),
- Fairchild (www.fairchildsemi.com),
- Microchip (www.microchip.com),
- Philips (www.semiconductor.philips.com),
- Rohm (www.rohm.com),
- ST (www.st.com),
- Xicor (www.xicor.com),
- and others.
-
- Chip Size (bits) Address
- 24C01 1K 0x50 (shadows at 0x51 - 0x57)
- 24C01A 1K 0x50 - 0x57 (Typical device on DIMMs)
- 24C02 2K 0x50 - 0x57
- 24C04 4K 0x50, 0x52, 0x54, 0x56
- (additional data at 0x51, 0x53, 0x55, 0x57)
- 24C08 8K 0x50, 0x54 (additional data at 0x51, 0x52,
- 0x53, 0x55, 0x56, 0x57)
- 24C16 16K 0x50 (additional data at 0x51 - 0x57)
- Sony 2K 0x57
-
- Atmel 34C02B 2K 0x50 - 0x57, SW write protect at 0x30-37
- Catalyst 34FC02 2K 0x50 - 0x57, SW write protect at 0x30-37
- Catalyst 34RC02 2K 0x50 - 0x57, SW write protect at 0x30-37
- Fairchild 34W02 2K 0x50 - 0x57, SW write protect at 0x30-37
- Microchip 24AA52 2K 0x50 - 0x57, SW write protect at 0x30-37
- ST M34C02 2K 0x50 - 0x57, SW write protect at 0x30-37
-
-
-Authors:
- Frodo Looijaard <frodol@dds.nl>,
- Philip Edelbrock <phil@netroedge.com>,
- Jean Delvare <khali@linux-fr.org>,
- Greg Kroah-Hartman <greg@kroah.com>,
- IBM Corp.
-
-Description
------------
-
-This is a simple EEPROM module meant to enable reading the first 256 bytes
-of an EEPROM (on a SDRAM DIMM for example). However, it will access serial
-EEPROMs on any I2C adapter. The supported devices are generically called
-24Cxx, and are listed above; however the numbering for these
-industry-standard devices may vary by manufacturer.
-
-This module was a programming exercise to get used to the new project
-organization laid out by Frodo, but it should be at least completely
-effective for decoding the contents of EEPROMs on DIMMs.
-
-DIMMS will typically contain a 24C01A or 24C02, or the 34C02 variants.
-The other devices will not be found on a DIMM because they respond to more
-than one address.
-
-DDC Monitors may contain any device. Often a 24C01, which responds to all 8
-addresses, is found.
-
-Recent Sony Vaio laptops have an EEPROM at 0x57. We couldn't get the
-specification, so it is guess work and far from being complete.
-
-The Microchip 24AA52/24LCS52, ST M34C02, and others support an additional
-software write protect register at 0x30 - 0x37 (0x20 less than the memory
-location). The chip responds to "write quick" detection at this address but
-does not respond to byte reads. If this register is present, the lower 128
-bytes of the memory array are not write protected. Any byte data write to
-this address will write protect the memory array permanently, and the
-device will no longer respond at the 0x30-37 address. The eeprom driver
-does not support this register.
-
-Lacking functionality:
-
-* Full support for larger devices (24C04, 24C08, 24C16). These are not
-typically found on a PC. These devices will appear as separate devices at
-multiple addresses.
-
-* Support for really large devices (24C32, 24C64, 24C128, 24C256, 24C512).
-These devices require two-byte address fields and are not supported.
-
-* Enable Writing. Again, no technical reason why not, but making it easy
-to change the contents of the EEPROMs (on DIMMs anyway) also makes it easy
-to disable the DIMMs (potentially preventing the computer from booting)
-until the values are restored somehow.
-
-Use:
-
-After inserting the module (and any other required SMBus/i2c modules), you
-should have some EEPROM directories in /sys/bus/i2c/devices/* of names such
-as "0-0050". Inside each of these is a series of files, the eeprom file
-contains the binary data from EEPROM.
+++ /dev/null
-Kernel driver max6875
-=====================
-
-Supported chips:
- * Maxim MAX6874, MAX6875
- Prefix: 'max6875'
- Addresses scanned: None (see below)
- Datasheet:
- http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf
-
-Author: Ben Gardner <bgardner@wabtec.com>
-
-
-Description
------------
-
-The Maxim MAX6875 is an EEPROM-programmable power-supply sequencer/supervisor.
-It provides timed outputs that can be used as a watchdog, if properly wired.
-It also provides 512 bytes of user EEPROM.
-
-At reset, the MAX6875 reads the configuration EEPROM into its configuration
-registers. The chip then begins to operate according to the values in the
-registers.
-
-The Maxim MAX6874 is a similar, mostly compatible device, with more intputs
-and outputs:
- vin gpi vout
-MAX6874 6 4 8
-MAX6875 4 3 5
-
-See the datasheet for more information.
-
-
-Sysfs entries
--------------
-
-eeprom - 512 bytes of user-defined EEPROM space.
-
-
-General Remarks
----------------
-
-Valid addresses for the MAX6875 are 0x50 and 0x52.
-Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56.
-The driver does not probe any address, so you must force the address.
-
-Example:
-$ modprobe max6875 force=0,0x50
-
-The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple
-addresses. For example, for address 0x50, it also reserves 0x51.
-The even-address instance is called 'max6875', the odd one is 'dummy'.
-
-
-Programming the chip using i2c-dev
-----------------------------------
-
-Use the i2c-dev interface to access and program the chips.
-Reads and writes are performed differently depending on the address range.
-
-The configuration registers are at addresses 0x00 - 0x45.
-Use i2c_smbus_write_byte_data() to write a register and
-i2c_smbus_read_byte_data() to read a register.
-The command is the register number.
-
-Examples:
-To write a 1 to register 0x45:
- i2c_smbus_write_byte_data(fd, 0x45, 1);
-
-To read register 0x45:
- value = i2c_smbus_read_byte_data(fd, 0x45);
-
-
-The configuration EEPROM is at addresses 0x8000 - 0x8045.
-The user EEPROM is at addresses 0x8100 - 0x82ff.
-
-Use i2c_smbus_write_word_data() to write a byte to EEPROM.
-
-The command is the upper byte of the address: 0x80, 0x81, or 0x82.
-The data word is the lower part of the address or'd with data << 8.
- cmd = address >> 8;
- val = (address & 0xff) | (data << 8);
-
-Example:
-To write 0x5a to address 0x8003:
- i2c_smbus_write_word_data(fd, 0x80, 0x5a03);
-
-
-Reading data from the EEPROM is a little more complicated.
-Use i2c_smbus_write_byte_data() to set the read address and then
-i2c_smbus_read_byte() or i2c_smbus_read_i2c_block_data() to read the data.
-
-Example:
-To read data starting at offset 0x8100, first set the address:
- i2c_smbus_write_byte_data(fd, 0x81, 0x00);
-
-And then read the data
- value = i2c_smbus_read_byte(fd);
-
- or
-
- count = i2c_smbus_read_i2c_block_data(fd, 0x84, 16, buffer);
-
-The block read should read 16 bytes.
-0x84 is the block read command.
-
-See the datasheet for more details.
-
deleted.
Example:
-# echo eeprom 0x50 > /sys/class/i2c-adapter/i2c-3/new_device
+# echo eeprom 0x50 > /sys/bus/i2c/devices/i2c-3/new_device
While this interface should only be used when in-kernel device declaration
can't be done, there is a variety of cases where it can be helpful:
<http://mikonos.dia.unisa.it/tcfs>
'l' 40-7F linux/udf_fs_i.h in development:
<http://sourceforge.net/projects/linux-udf/>
+'m' 00-09 linux/mmtimer.h
'm' all linux/mtio.h conflict!
'm' all linux/soundcard.h conflict!
'm' all linux/synclink.h conflict!
earlyprintk= [X86,SH,BLACKFIN]
earlyprintk=vga
earlyprintk=serial[,ttySn[,baudrate]]
+ earlyprintk=ttySn[,baudrate]
earlyprintk=dbgp[debugController#]
Append ",keep" to not disable it when the real console
Not all bits in the mask can be modified. Not all bits that can be
modified do anything. Not all hot keys can be individually controlled
-by the mask. Some models do not support the mask at all, and in those
-models, hot keys cannot be controlled individually. The behaviour of
-the mask is, therefore, highly dependent on the ThinkPad model.
+by the mask. Some models do not support the mask at all. The behaviour
+of the mask is, therefore, highly dependent on the ThinkPad model.
+
+The driver will filter out any unmasked hotkeys, so even if the firmware
+doesn't allow disabling an specific hotkey, the driver will not report
+events for unmasked hotkeys.
Note that unmasking some keys prevents their default behavior. For
example, if Fn+F5 is unmasked, that key will no longer enable/disable
-Bluetooth by itself.
+Bluetooth by itself in firmware.
-Note also that not all Fn key combinations are supported through ACPI.
-For example, on the X40, the brightness, volume and "Access IBM" buttons
-do not generate ACPI events even with this driver. They *can* be used
-through the "ThinkPad Buttons" utility, see http://www.nongnu.org/tpb/
+Note also that not all Fn key combinations are supported through ACPI
+depending on the ThinkPad model and firmware version. On those
+ThinkPads, it is still possible to support some extra hotkeys by
+polling the "CMOS NVRAM" at least 10 times per second. The driver
+attempts to enables this functionality automatically when required.
procfs notes:
1: does nothing
hotkey_mask:
- bit mask to enable driver-handling (and depending on
+ bit mask to enable reporting (and depending on
the firmware, ACPI event generation) for each hot key
(see above). Returns the current status of the hot keys
mask, and allows one to modify it.
- Note: when NVRAM polling is active, the firmware mask
- will be different from the value returned by
- hotkey_mask. The driver will retain enabled bits for
- hotkeys that are under NVRAM polling even if the
- firmware refuses them, and will not set these bits on
- the firmware hot key mask.
-
hotkey_all_mask:
bit mask that should enable event reporting for all
supported hot keys, when echoed to hotkey_mask above.
bit mask that should enable event reporting for all
supported hot keys, except those which are always
handled by the firmware anyway. Echo it to
- hotkey_mask above, to use.
+ hotkey_mask above, to use. This is the default mask
+ used by the driver.
hotkey_source_mask:
bit mask that selects which hot keys will the driver
based on the capabilities reported by the ACPI firmware,
but it can be overridden at runtime.
- Hot keys whose bits are set in both hotkey_source_mask
- and also on hotkey_mask are polled for in NVRAM. Only a
- few hot keys are available through CMOS NVRAM polling.
+ Hot keys whose bits are set in hotkey_source_mask are
+ polled for in NVRAM, and reported as hotkey events if
+ enabled in hotkey_mask. Only a few hot keys are
+ available through CMOS NVRAM polling.
Warning: when in NVRAM mode, the volume up/down/mute
keys are synthesized according to changes in the mixer,
0x2305 System is waking up from suspend to eject bay
0x2404 System is waking up from hibernation to undock
0x2405 System is waking up from hibernation to eject bay
+0x5010 Brightness level changed/control event
The above events are never propagated by the driver.
0x4003 Undocked (see 0x2x04), can sleep again
0x500B Tablet pen inserted into its storage bay
0x500C Tablet pen removed from its storage bay
-0x5010 Brightness level changed (newer Lenovo BIOSes)
The above events are propagated by the driver.
2. Do *NOT* load up ACPI video, enable the hotkeys in thinkpad-acpi,
and map them to KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN. Process
these keys on userspace somehow (e.g. by calling xbacklight).
+ The driver will do this automatically if it detects that ACPI video
+ has been disabled.
Bluetooth
0x020400: Marker for 16 LEDs support. Also, LEDs that are known
to not exist in a given model are not registered with
the LED sysfs class anymore.
+
+0x020500: Updated hotkey driver, hotkey_mask is always available
+ and it is always able to disable hot keys. Very old
+ thinkpads are properly supported. hotkey_bios_mask
+ is deprecated and marked for removal.
--- /dev/null
+Kernel driver eeprom
+====================
+
+Supported chips:
+ * Any EEPROM chip in the designated address range
+ Prefix: 'eeprom'
+ Addresses scanned: I2C 0x50 - 0x57
+ Datasheets: Publicly available from:
+ Atmel (www.atmel.com),
+ Catalyst (www.catsemi.com),
+ Fairchild (www.fairchildsemi.com),
+ Microchip (www.microchip.com),
+ Philips (www.semiconductor.philips.com),
+ Rohm (www.rohm.com),
+ ST (www.st.com),
+ Xicor (www.xicor.com),
+ and others.
+
+ Chip Size (bits) Address
+ 24C01 1K 0x50 (shadows at 0x51 - 0x57)
+ 24C01A 1K 0x50 - 0x57 (Typical device on DIMMs)
+ 24C02 2K 0x50 - 0x57
+ 24C04 4K 0x50, 0x52, 0x54, 0x56
+ (additional data at 0x51, 0x53, 0x55, 0x57)
+ 24C08 8K 0x50, 0x54 (additional data at 0x51, 0x52,
+ 0x53, 0x55, 0x56, 0x57)
+ 24C16 16K 0x50 (additional data at 0x51 - 0x57)
+ Sony 2K 0x57
+
+ Atmel 34C02B 2K 0x50 - 0x57, SW write protect at 0x30-37
+ Catalyst 34FC02 2K 0x50 - 0x57, SW write protect at 0x30-37
+ Catalyst 34RC02 2K 0x50 - 0x57, SW write protect at 0x30-37
+ Fairchild 34W02 2K 0x50 - 0x57, SW write protect at 0x30-37
+ Microchip 24AA52 2K 0x50 - 0x57, SW write protect at 0x30-37
+ ST M34C02 2K 0x50 - 0x57, SW write protect at 0x30-37
+
+
+Authors:
+ Frodo Looijaard <frodol@dds.nl>,
+ Philip Edelbrock <phil@netroedge.com>,
+ Jean Delvare <khali@linux-fr.org>,
+ Greg Kroah-Hartman <greg@kroah.com>,
+ IBM Corp.
+
+Description
+-----------
+
+This is a simple EEPROM module meant to enable reading the first 256 bytes
+of an EEPROM (on a SDRAM DIMM for example). However, it will access serial
+EEPROMs on any I2C adapter. The supported devices are generically called
+24Cxx, and are listed above; however the numbering for these
+industry-standard devices may vary by manufacturer.
+
+This module was a programming exercise to get used to the new project
+organization laid out by Frodo, but it should be at least completely
+effective for decoding the contents of EEPROMs on DIMMs.
+
+DIMMS will typically contain a 24C01A or 24C02, or the 34C02 variants.
+The other devices will not be found on a DIMM because they respond to more
+than one address.
+
+DDC Monitors may contain any device. Often a 24C01, which responds to all 8
+addresses, is found.
+
+Recent Sony Vaio laptops have an EEPROM at 0x57. We couldn't get the
+specification, so it is guess work and far from being complete.
+
+The Microchip 24AA52/24LCS52, ST M34C02, and others support an additional
+software write protect register at 0x30 - 0x37 (0x20 less than the memory
+location). The chip responds to "write quick" detection at this address but
+does not respond to byte reads. If this register is present, the lower 128
+bytes of the memory array are not write protected. Any byte data write to
+this address will write protect the memory array permanently, and the
+device will no longer respond at the 0x30-37 address. The eeprom driver
+does not support this register.
+
+Lacking functionality:
+
+* Full support for larger devices (24C04, 24C08, 24C16). These are not
+typically found on a PC. These devices will appear as separate devices at
+multiple addresses.
+
+* Support for really large devices (24C32, 24C64, 24C128, 24C256, 24C512).
+These devices require two-byte address fields and are not supported.
+
+* Enable Writing. Again, no technical reason why not, but making it easy
+to change the contents of the EEPROMs (on DIMMs anyway) also makes it easy
+to disable the DIMMs (potentially preventing the computer from booting)
+until the values are restored somehow.
+
+Use:
+
+After inserting the module (and any other required SMBus/i2c modules), you
+should have some EEPROM directories in /sys/bus/i2c/devices/* of names such
+as "0-0050". Inside each of these is a series of files, the eeprom file
+contains the binary data from EEPROM.
--- /dev/null
+Kernel driver max6875
+=====================
+
+Supported chips:
+ * Maxim MAX6874, MAX6875
+ Prefix: 'max6875'
+ Addresses scanned: None (see below)
+ Datasheet:
+ http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf
+
+Author: Ben Gardner <bgardner@wabtec.com>
+
+
+Description
+-----------
+
+The Maxim MAX6875 is an EEPROM-programmable power-supply sequencer/supervisor.
+It provides timed outputs that can be used as a watchdog, if properly wired.
+It also provides 512 bytes of user EEPROM.
+
+At reset, the MAX6875 reads the configuration EEPROM into its configuration
+registers. The chip then begins to operate according to the values in the
+registers.
+
+The Maxim MAX6874 is a similar, mostly compatible device, with more intputs
+and outputs:
+ vin gpi vout
+MAX6874 6 4 8
+MAX6875 4 3 5
+
+See the datasheet for more information.
+
+
+Sysfs entries
+-------------
+
+eeprom - 512 bytes of user-defined EEPROM space.
+
+
+General Remarks
+---------------
+
+Valid addresses for the MAX6875 are 0x50 and 0x52.
+Valid addresses for the MAX6874 are 0x50, 0x52, 0x54 and 0x56.
+The driver does not probe any address, so you explicitly instantiate the
+devices.
+
+Example:
+$ modprobe max6875
+$ echo max6875 0x50 > /sys/bus/i2c/devices/i2c-0/new_device
+
+The MAX6874/MAX6875 ignores address bit 0, so this driver attaches to multiple
+addresses. For example, for address 0x50, it also reserves 0x51.
+The even-address instance is called 'max6875', the odd one is 'dummy'.
+
+
+Programming the chip using i2c-dev
+----------------------------------
+
+Use the i2c-dev interface to access and program the chips.
+Reads and writes are performed differently depending on the address range.
+
+The configuration registers are at addresses 0x00 - 0x45.
+Use i2c_smbus_write_byte_data() to write a register and
+i2c_smbus_read_byte_data() to read a register.
+The command is the register number.
+
+Examples:
+To write a 1 to register 0x45:
+ i2c_smbus_write_byte_data(fd, 0x45, 1);
+
+To read register 0x45:
+ value = i2c_smbus_read_byte_data(fd, 0x45);
+
+
+The configuration EEPROM is at addresses 0x8000 - 0x8045.
+The user EEPROM is at addresses 0x8100 - 0x82ff.
+
+Use i2c_smbus_write_word_data() to write a byte to EEPROM.
+
+The command is the upper byte of the address: 0x80, 0x81, or 0x82.
+The data word is the lower part of the address or'd with data << 8.
+ cmd = address >> 8;
+ val = (address & 0xff) | (data << 8);
+
+Example:
+To write 0x5a to address 0x8003:
+ i2c_smbus_write_word_data(fd, 0x80, 0x5a03);
+
+
+Reading data from the EEPROM is a little more complicated.
+Use i2c_smbus_write_byte_data() to set the read address and then
+i2c_smbus_read_byte() or i2c_smbus_read_i2c_block_data() to read the data.
+
+Example:
+To read data starting at offset 0x8100, first set the address:
+ i2c_smbus_write_byte_data(fd, 0x81, 0x00);
+
+And then read the data
+ value = i2c_smbus_read_byte(fd);
+
+ or
+
+ count = i2c_smbus_read_i2c_block_data(fd, 0x84, 16, buffer);
+
+The block read should read 16 bytes.
+0x84 is the block read command.
+
+See the datasheet for more details.
+
memset(&hwtstamp, 0, sizeof(hwtstamp));
strncpy(hwtstamp.ifr_name, interface, sizeof(hwtstamp.ifr_name));
hwtstamp.ifr_data = (void *)&hwconfig;
- memset(&hwconfig, 0, sizeof(&hwconfig));
+ memset(&hwconfig, 0, sizeof(hwconfig));
hwconfig.tx_type =
(so_timestamping_flags & SOF_TIMESTAMPING_TX_HARDWARE) ?
HWTSTAMP_TX_ON : HWTSTAMP_TX_OFF;
laptop laptop with HP jack sensing
mobile mobile devices with HP jack sensing
thinkpad Lenovo Thinkpad X300
+ touchsmart HP Touchsmart
AD1884
======
of error messages about running out of file handles, you might
want to increase this limit.
-The three values in file-nr denote the number of allocated
-file handles, the number of unused file handles and the maximum
-number of file handles. When the allocated file handles come
-close to the maximum, but the number of unused file handles is
-significantly greater than 0, you've encountered a peak in your
-usage of file handles and you don't need to increase the maximum.
-
+Historically, the three values in file-nr denoted the number of
+allocated file handles, the number of allocated but unused file
+handles, and the maximum number of file handles. Linux 2.6 always
+reports 0 as the number of free file handles -- this is not an
+error, it just means that the number of allocated file handles
+exactly matches the number of used file handles.
+
+Attempts to allocate more file descriptors than file-max are
+reported with printk, look for "VFS: file-max limit <number>
+reached".
==============================================================
nr_open:
- callhome [ S390 only ]
- auto_msgmni
- core_pattern
+- core_pipe_limit
- core_uses_pid
- ctrl-alt-del
- dentry-state
==============================================================
+core_pipe_limit:
+
+This sysctl is only applicable when core_pattern is configured to pipe core
+files to user space helper a (when the first character of core_pattern is a '|',
+see above). When collecting cores via a pipe to an application, it is
+occasionally usefull for the collecting application to gather data about the
+crashing process from its /proc/pid directory. In order to do this safely, the
+kernel must wait for the collecting process to exit, so as not to remove the
+crashing processes proc files prematurely. This in turn creates the possibility
+that a misbehaving userspace collecting process can block the reaping of a
+crashed process simply by never exiting. This sysctl defends against that. It
+defines how many concurrent crashing processes may be piped to user space
+applications in parallel. If this value is exceeded, then those crashing
+processes above that value are noted via the kernel log and their cores are
+skipped. 0 is a special value, indicating that unlimited processes may be
+captured in parallel, but that no waiting will take place (i.e. the collecting
+process is not guaranteed access to /proc/<crahing pid>/). This value defaults
+to 0.
+
+==============================================================
+
core_uses_pid:
The default coredump filename is "core". By setting
- legacy_va_layout
- lowmem_reserve_ratio
- max_map_count
+- memory_failure_early_kill
+- memory_failure_recovery
- min_free_kbytes
- min_slab_ratio
- min_unmapped_ratio
- vfs_cache_pressure
- zone_reclaim_mode
-
==============================================================
block_dump
The default value is 65536.
+=============================================================
+
+memory_failure_early_kill:
+
+Control how to kill processes when uncorrected memory error (typically
+a 2bit error in a memory module) is detected in the background by hardware
+that cannot be handled by the kernel. In some cases (like the page
+still having a valid copy on disk) the kernel will handle the failure
+transparently without affecting any applications. But if there is
+no other uptodate copy of the data it will kill to prevent any data
+corruptions from propagating.
+
+1: Kill all processes that have the corrupted and not reloadable page mapped
+as soon as the corruption is detected. Note this is not supported
+for a few types of pages, like kernel internally allocated data or
+the swap cache, but works for the majority of user pages.
+
+0: Only unmap the corrupted page from all processes and only kill a process
+who tries to access it.
+
+The kill is done using a catchable SIGBUS with BUS_MCEERR_AO, so processes can
+handle this if they want to.
+
+This is only active on architectures/platforms with advanced machine
+check handling and depends on the hardware capabilities.
+
+Applications can override this setting individually with the PR_MCE_KILL prctl
+
+==============================================================
+
+memory_failure_recovery
+
+Enable memory failure recovery (when supported by the platform)
+
+1: Attempt recovery.
+
+0: Always panic on a memory failure.
+
==============================================================
min_free_kbytes:
mm start up ... this is a loose form of stability on mm_users. For
example, it is used in copy_mm to protect against a racing tlb_gather_mmu
single address space optimization, so that the zap_page_range (from
-vmtruncate) does not lose sending ipi's to cloned threads that might
+truncate) does not lose sending ipi's to cloned threads that might
be spawned underneath it and go to user mode to drag in pte's into tlbs.
swap_lock
* Copyright (C) 2009 Wu Fengguang <fengguang.wu@intel.com>
*/
+#define _LARGEFILE64_SOURCE
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <getopt.h>
#include <limits.h>
+#include <assert.h>
#include <sys/types.h>
#include <sys/errno.h>
#include <sys/fcntl.h>
+/*
+ * pagemap kernel ABI bits
+ */
+
+#define PM_ENTRY_BYTES sizeof(uint64_t)
+#define PM_STATUS_BITS 3
+#define PM_STATUS_OFFSET (64 - PM_STATUS_BITS)
+#define PM_STATUS_MASK (((1LL << PM_STATUS_BITS) - 1) << PM_STATUS_OFFSET)
+#define PM_STATUS(nr) (((nr) << PM_STATUS_OFFSET) & PM_STATUS_MASK)
+#define PM_PSHIFT_BITS 6
+#define PM_PSHIFT_OFFSET (PM_STATUS_OFFSET - PM_PSHIFT_BITS)
+#define PM_PSHIFT_MASK (((1LL << PM_PSHIFT_BITS) - 1) << PM_PSHIFT_OFFSET)
+#define PM_PSHIFT(x) (((u64) (x) << PM_PSHIFT_OFFSET) & PM_PSHIFT_MASK)
+#define PM_PFRAME_MASK ((1LL << PM_PSHIFT_OFFSET) - 1)
+#define PM_PFRAME(x) ((x) & PM_PFRAME_MASK)
+
+#define PM_PRESENT PM_STATUS(4LL)
+#define PM_SWAP PM_STATUS(2LL)
+
+
/*
* kernel page flags
*/
static unsigned long opt_offset[MAX_ADDR_RANGES];
static unsigned long opt_size[MAX_ADDR_RANGES];
+#define MAX_VMAS 10240
+static int nr_vmas;
+static unsigned long pg_start[MAX_VMAS];
+static unsigned long pg_end[MAX_VMAS];
+static unsigned long voffset;
+
+static int pagemap_fd;
+
#define MAX_BIT_FILTERS 64
static int nr_bit_filters;
static uint64_t opt_mask[MAX_BIT_FILTERS];
#define PAGES_BATCH (64 << 10) /* 64k pages */
static int kpageflags_fd;
-static uint64_t kpageflags_buf[KPF_BYTES * PAGES_BATCH];
#define HASH_SHIFT 13
#define HASH_SIZE (1 << HASH_SHIFT)
type __min2 = (y); \
__min1 < __min2 ? __min1 : __min2; })
+#define max_t(type, x, y) ({ \
+ type __max1 = (x); \
+ type __max2 = (y); \
+ __max1 > __max2 ? __max1 : __max2; })
+
static unsigned long pages2mb(unsigned long pages)
{
return (pages * page_size) >> 20;
static void show_page_range(unsigned long offset, uint64_t flags)
{
static uint64_t flags0;
+ static unsigned long voff;
static unsigned long index;
static unsigned long count;
- if (flags == flags0 && offset == index + count) {
+ if (flags == flags0 && offset == index + count &&
+ (!opt_pid || voffset == voff + count)) {
count++;
return;
}
- if (count)
- printf("%lu\t%lu\t%s\n",
+ if (count) {
+ if (opt_pid)
+ printf("%lx\t", voff);
+ printf("%lx\t%lx\t%s\n",
index, count, page_flag_name(flags0));
+ }
flags0 = flags;
index = offset;
+ voff = voffset;
count = 1;
}
static void show_page(unsigned long offset, uint64_t flags)
{
- printf("%lu\t%s\n", offset, page_flag_name(flags));
+ if (opt_pid)
+ printf("%lx\t", voffset);
+ printf("%lx\t%s\n", offset, page_flag_name(flags));
}
static void show_summary(void)
lseek(kpageflags_fd, index * KPF_BYTES, SEEK_SET);
while (count) {
+ uint64_t kpageflags_buf[KPF_BYTES * PAGES_BATCH];
+
batch = min_t(unsigned long, count, PAGES_BATCH);
n = read(kpageflags_fd, kpageflags_buf, batch * KPF_BYTES);
if (n == 0)
}
}
+
+#define PAGEMAP_BATCH 4096
+static unsigned long task_pfn(unsigned long pgoff)
+{
+ static uint64_t buf[PAGEMAP_BATCH];
+ static unsigned long start;
+ static long count;
+ uint64_t pfn;
+
+ if (pgoff < start || pgoff >= start + count) {
+ if (lseek64(pagemap_fd,
+ (uint64_t)pgoff * PM_ENTRY_BYTES,
+ SEEK_SET) < 0) {
+ perror("pagemap seek");
+ exit(EXIT_FAILURE);
+ }
+ count = read(pagemap_fd, buf, sizeof(buf));
+ if (count == 0)
+ return 0;
+ if (count < 0) {
+ perror("pagemap read");
+ exit(EXIT_FAILURE);
+ }
+ if (count % PM_ENTRY_BYTES) {
+ fatal("pagemap read not aligned.\n");
+ exit(EXIT_FAILURE);
+ }
+ count /= PM_ENTRY_BYTES;
+ start = pgoff;
+ }
+
+ pfn = buf[pgoff - start];
+ if (pfn & PM_PRESENT)
+ pfn = PM_PFRAME(pfn);
+ else
+ pfn = 0;
+
+ return pfn;
+}
+
+static void walk_task(unsigned long index, unsigned long count)
+{
+ int i = 0;
+ const unsigned long end = index + count;
+
+ while (index < end) {
+
+ while (pg_end[i] <= index)
+ if (++i >= nr_vmas)
+ return;
+ if (pg_start[i] >= end)
+ return;
+
+ voffset = max_t(unsigned long, pg_start[i], index);
+ index = min_t(unsigned long, pg_end[i], end);
+
+ assert(voffset < index);
+ for (; voffset < index; voffset++) {
+ unsigned long pfn = task_pfn(voffset);
+ if (pfn)
+ walk_pfn(pfn, 1);
+ }
+ }
+}
+
+static void add_addr_range(unsigned long offset, unsigned long size)
+{
+ if (nr_addr_ranges >= MAX_ADDR_RANGES)
+ fatal("too many addr ranges\n");
+
+ opt_offset[nr_addr_ranges] = offset;
+ opt_size[nr_addr_ranges] = min_t(unsigned long, size, ULONG_MAX-offset);
+ nr_addr_ranges++;
+}
+
static void walk_addr_ranges(void)
{
int i;
}
if (!nr_addr_ranges)
- walk_pfn(0, ULONG_MAX);
+ add_addr_range(0, ULONG_MAX);
for (i = 0; i < nr_addr_ranges; i++)
- walk_pfn(opt_offset[i], opt_size[i]);
+ if (!opt_pid)
+ walk_pfn(opt_offset[i], opt_size[i]);
+ else
+ walk_task(opt_offset[i], opt_size[i]);
close(kpageflags_fd);
}
" -r|--raw Raw mode, for kernel developers\n"
" -a|--addr addr-spec Walk a range of pages\n"
" -b|--bits bits-spec Walk pages with specified bits\n"
-#if 0 /* planned features */
" -p|--pid pid Walk process address space\n"
+#if 0 /* planned features */
" -f|--file filename Walk file address space\n"
#endif
" -l|--list Show page details in ranges\n"
" N+M pages range from N to N+M-1\n"
" N,M pages range from N to M-1\n"
" N, pages range from N to end\n"
-" ,M pages range from 0 to M\n"
+" ,M pages range from 0 to M-1\n"
"bits-spec:\n"
" bit1,bit2 (flags & (bit1|bit2)) != 0\n"
" bit1,bit2=bit1 (flags & (bit1|bit2)) == bit1\n"
static void parse_pid(const char *str)
{
+ FILE *file;
+ char buf[5000];
+
opt_pid = parse_number(str);
-}
-static void parse_file(const char *name)
-{
+ sprintf(buf, "/proc/%d/pagemap", opt_pid);
+ pagemap_fd = open(buf, O_RDONLY);
+ if (pagemap_fd < 0) {
+ perror(buf);
+ exit(EXIT_FAILURE);
+ }
+
+ sprintf(buf, "/proc/%d/maps", opt_pid);
+ file = fopen(buf, "r");
+ if (!file) {
+ perror(buf);
+ exit(EXIT_FAILURE);
+ }
+
+ while (fgets(buf, sizeof(buf), file) != NULL) {
+ unsigned long vm_start;
+ unsigned long vm_end;
+ unsigned long long pgoff;
+ int major, minor;
+ char r, w, x, s;
+ unsigned long ino;
+ int n;
+
+ n = sscanf(buf, "%lx-%lx %c%c%c%c %llx %x:%x %lu",
+ &vm_start,
+ &vm_end,
+ &r, &w, &x, &s,
+ &pgoff,
+ &major, &minor,
+ &ino);
+ if (n < 10) {
+ fprintf(stderr, "unexpected line: %s\n", buf);
+ continue;
+ }
+ pg_start[nr_vmas] = vm_start / page_size;
+ pg_end[nr_vmas] = vm_end / page_size;
+ if (++nr_vmas >= MAX_VMAS) {
+ fprintf(stderr, "too many VMAs\n");
+ break;
+ }
+ }
+ fclose(file);
}
-static void add_addr_range(unsigned long offset, unsigned long size)
+static void parse_file(const char *name)
{
- if (nr_addr_ranges >= MAX_ADDR_RANGES)
- fatal("too much addr ranges\n");
-
- opt_offset[nr_addr_ranges] = offset;
- opt_size[nr_addr_ranges] = size;
- nr_addr_ranges++;
}
static void parse_addr_range(const char *optarg)
}
}
+ if (opt_list && opt_pid)
+ printf("voffset\t");
if (opt_list == 1)
- printf("offset\tcount\tflags\n");
+ printf("offset\tlen\tflags\n");
if (opt_list == 2)
printf("offset\tflags\n");
Valid addresses are 0x18, 0x19, 0x1a, and 0x1b.
However, the device cannot be detected without writing to the i2c bus, so no
-detection is done.
-You should force the device address.
+detection is done. You should instantiate the device explicitly.
-$ modprobe ds2482 force=0,0x18
+$ modprobe ds2482
+$ echo ds2482 0x18 > /sys/bus/i2c/devices/i2c-0/new_device
S: Supported
F: drivers/acpi/fan.c
-ACPI PCI HOTPLUG DRIVER
-M: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
-L: linux-pci@vger.kernel.org
+ACPI PROCESSOR AGGREGATOR DRIVER
+M: Shaohua Li <shaohua.li@intel.com>
+L: linux-acpi@vger.kernel.org
+W: http://www.lesswatts.org/projects/acpi/
S: Supported
-F: drivers/pci/hotplug/acpi*
+F: drivers/acpi/acpi_pad.c
ACPI THERMAL DRIVER
M: Zhang Rui <rui.zhang@intel.com>
M: Lennert Buytenhek <kernel@wantstofly.org>
M: Dan Williams <dan.j.williams@intel.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Supported
+S: Maintained
ARM/INTEL IOP33X ARM ARCHITECTURE
M: Dan Williams <dan.j.williams@intel.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Supported
+S: Maintained
ARM/INTEL IOP13XX ARM ARCHITECTURE
M: Lennert Buytenhek <kernel@wantstofly.org>
M: Dan Williams <dan.j.williams@intel.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Supported
+S: Maintained
ARM/INTEL IQ81342EX MACHINE SUPPORT
M: Lennert Buytenhek <kernel@wantstofly.org>
M: Dan Williams <dan.j.williams@intel.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Supported
+S: Maintained
ARM/INTEL IXP2000 ARM ARCHITECTURE
M: Lennert Buytenhek <kernel@wantstofly.org>
ARM/INTEL IXP4XX ARM ARCHITECTURE
M: Imre Kaloz <kaloz@openwrt.org>
M: Krzysztof Halasa <khc@pm.waw.pl>
-L: linux-arm-kernel@lists.infradead.org
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-ixp4xx/
M: Lennert Buytenhek <kernel@wantstofly.org>
M: Dan Williams <dan.j.williams@intel.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S: Supported
+S: Maintained
ARM/IP FABRICS DOUBLE ESPRESSO MACHINE SUPPORT
M: Lennert Buytenhek <kernel@wantstofly.org>
M: Dirk Opfer <dirk@opfer-online.de>
S: Maintained
-ARM/PALMTX,PALMT5,PALMLD,PALMTE2 SUPPORT
+ARM/PALMTX,PALMT5,PALMLD,PALMTE2,PALMTC SUPPORT
M: Marek Vasut <marek.vasut@gmail.com>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
+F: arch/arm/mach-pxa/include/mach/palmtx.h
+F: arch/arm/mach-pxa/palmtx.c
+F: arch/arm/mach-pxa/include/mach/palmt5.h
+F: arch/arm/mach-pxa/palmt5.c
+F: arch/arm/mach-pxa/include/mach/palmld.h
+F: arch/arm/mach-pxa/palmld.c
+F: arch/arm/mach-pxa/include/mach/palmte2.h
+F: arch/arm/mach-pxa/palmte2.c
+F: arch/arm/mach-pxa/include/mach/palmtc.h
+F: arch/arm/mach-pxa/palmtc.c
ARM/PALM TREO 680 SUPPORT
M: Tomas Cech <sleep_walker@suse.cz>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
+F: arch/arm/mach-pxa/include/mach/treo680.h
+F: arch/arm/mach-pxa/treo680.c
ARM/PALMZ72 SUPPORT
M: Sergey Lapin <slapin@ossfans.org>
+L: linux-arm-kernel@lists.infradead.org
W: http://hackndev.com
S: Maintained
+F: arch/arm/mach-pxa/include/mach/palmz72.h
+F: arch/arm/mach-pxa/palmz72.c
ARM/PLEB SUPPORT
M: Peter Chubb <pleb@gelato.unsw.edu.au>
F: drivers/hwmon/
HARDWARE RANDOM NUMBER GENERATOR CORE
-S: Orphan
+M: Matt Mackall <mpm@selenic.com>
+M: Herbert Xu <herbert@gondor.apana.org.au>
+S: Odd fixes
F: Documentation/hw_random.txt
F: drivers/char/hw_random/
F: include/linux/hw_random.h
INTEL IOP-ADMA DMA DRIVER
M: Dan Williams <dan.j.williams@intel.com>
-S: Supported
+S: Maintained
F: drivers/dma/iop-adma.c
INTEL IXP4XX QMGR, NPE, ETHERNET and HSS SUPPORT
F: drivers/pci/
F: include/linux/pci*
-PCIE HOTPLUG DRIVER
-M: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
+PCI HOTPLUG
+M: Jesse Barnes <jbarnes@virtuousgeek.org>
L: linux-pci@vger.kernel.org
S: Supported
-F: drivers/pci/pcie/
+F: drivers/pci/hotplug
PCMCIA SUBSYSTEM
P: Linux PCMCIA Team
F: drivers/usb/gadget/lh7a40*
F: drivers/usb/host/ohci-lh7a40*
-SHPC HOTPLUG DRIVER
-M: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
-L: linux-pci@vger.kernel.org
-S: Supported
-F: drivers/pci/hotplug/shpchp*
-
SIMPLE FIRMWARE INTERFACE (SFI)
P: Len Brown
M: lenb@kernel.org
F: drivers/sfi/
F: include/linux/sfi*.h
-
SIMTEC EB110ATX (Chalice CATS)
P: Ben Dooks
M: Vincent Sanders <support@simtec.co.uk>
VERSION = 2
PATCHLEVEL = 6
-SUBLEVEL = 31
-EXTRAVERSION =
+SUBLEVEL = 32
+EXTRAVERSION = -rc3
NAME = Man-Eating Seals of Antiquity
# *DOCUMENTATION*
#define F_GETOWN 6 /* for sockets. */
#define F_SETSIG 10 /* for sockets. */
#define F_GETSIG 11 /* for sockets. */
+#define F_SETOWN_EX 12
+#define F_GETOWN_EX 13
/* for posix fcntl() and lockf() */
#define F_RDLCK 1
{
struct marvel_agp_aperture *aper = agp->aperture.sysdata;
return iommu_bind(aper->arena, aper->pg_start + pg_start,
- mem->page_count, mem->memory);
+ mem->page_count, mem->pages);
}
static int
{
struct titan_agp_aperture *aper = agp->aperture.sysdata;
return iommu_bind(aper->arena, aper->pg_start + pg_start,
- mem->page_count, mem->memory);
+ mem->page_count, mem->pages);
}
static int
struct task_struct init_task = INIT_TASK(init_task);
EXPORT_SYMBOL(init_task);
-union thread_union init_thread_union
- __attribute__((section(".data.init_thread")))
- = { INIT_THREAD_INFO(init_task) };
+union thread_union init_thread_union __init_task_data =
+ { INIT_THREAD_INFO(init_task) };
extern int iommu_reserve(struct pci_iommu_arena *, long, long);
extern int iommu_release(struct pci_iommu_arena *, long, long);
-extern int iommu_bind(struct pci_iommu_arena *, long, long, unsigned long *);
+extern int iommu_bind(struct pci_iommu_arena *, long, long, struct page **);
extern int iommu_unbind(struct pci_iommu_arena *, long, long);
int
iommu_bind(struct pci_iommu_arena *arena, long pg_start, long pg_count,
- unsigned long *physaddrs)
+ struct page **pages)
{
unsigned long flags;
unsigned long *ptes;
}
for(i = 0, j = pg_start; i < pg_count; i++, j++)
- ptes[j] = mk_iommu_pte(physaddrs[i]);
+ ptes[j] = mk_iommu_pte(page_to_phys(pages[i]));
spin_unlock_irqrestore(&arena->lock, flags);
#include <asm-generic/vmlinux.lds.h>
+#include <asm/thread_info.h>
#include <asm/page.h>
OUTPUT_FORMAT("elf64-alpha")
} :kernel
RODATA
-
- /* Exception table */
- . = ALIGN(16);
- __ex_table : {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
+ EXCEPTION_TABLE(16)
/* Will be freed after init */
- . = ALIGN(PAGE_SIZE);
- /* Init code and data */
- __init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
- .init.data : {
- INIT_DATA
- }
-
- . = ALIGN(16);
- .init.setup : {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
- }
-
- . = ALIGN(8);
- .initcall.init : {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
- }
-
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(PAGE_SIZE);
- .init.ramfs : {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
- }
-#endif
-
- . = ALIGN(8);
- .con_initcall.init : {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
- }
-
- . = ALIGN(8);
- SECURITY_INIT
-
+ __init_begin = ALIGN(PAGE_SIZE);
+ INIT_TEXT_SECTION(PAGE_SIZE)
+ INIT_DATA_SECTION(16)
PERCPU(PAGE_SIZE)
-
- . = ALIGN(2 * PAGE_SIZE);
+ /* Align to THREAD_SIZE rather than PAGE_SIZE here so any padding page
+ needed for the THREAD_SIZE aligned init_task gets freed after init */
+ . = ALIGN(THREAD_SIZE);
__init_end = .;
/* Freed after init ends here */
- /* Note 2 page alignment above. */
- .data.init_thread : {
- *(.data.init_thread)
- }
-
- . = ALIGN(PAGE_SIZE);
- .data.page_aligned : {
- *(.data.page_aligned)
- }
-
- . = ALIGN(64);
- .data.cacheline_aligned : {
- *(.data.cacheline_aligned)
- }
-
_data = .;
- /* Data */
- .data : {
- DATA_DATA
- CONSTRUCTORS
- }
+ RW_DATA_SECTION(64, PAGE_SIZE, THREAD_SIZE)
.got : {
*(.got)
}
_edata = .; /* End of data section */
- __bss_start = .;
- .sbss : {
- *(.sbss)
- *(.scommon)
- }
- .bss : {
- *(.bss)
- *(COMMON)
- }
- __bss_stop = .;
+ BSS_SECTION(0, 0, 0)
_end = .;
.mdebug 0 : {
depends on GENERIC_CLOCKEVENTS
default y if SMP && !LOCAL_TIMERS
+config HAVE_TCM
+ bool
+ select GENERIC_ALLOCATOR
+
config NO_IOPORT
bool
bool "ST-Ericsson U300 Series"
depends on MMU
select CPU_ARM926T
+ select HAVE_TCM
select ARM_AMBA
select ARM_VIC
select GENERIC_TIME
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_gpio_set_dir);
int locomo_gpio_read_level(struct device *dev, unsigned int bits)
{
ret &= bits;
return ret;
}
+EXPORT_SYMBOL(locomo_gpio_read_level);
int locomo_gpio_read_output(struct device *dev, unsigned int bits)
{
ret &= bits;
return ret;
}
+EXPORT_SYMBOL(locomo_gpio_read_output);
void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set)
{
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_gpio_write);
static void locomo_m62332_sendbit(void *mapbase, int bit)
{
spin_unlock_irqrestore(&lchip->lock, flags);
}
+EXPORT_SYMBOL(locomo_m62332_senddata);
/*
* Frontlight control
*/
-static struct locomo *locomo_chip_driver(struct locomo_dev *ldev);
-
void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf)
{
unsigned long flags;
driver->drv.bus = &locomo_bus_type;
return driver_register(&driver->drv);
}
+EXPORT_SYMBOL(locomo_driver_register);
void locomo_driver_unregister(struct locomo_driver *driver)
{
driver_unregister(&driver->drv);
}
+EXPORT_SYMBOL(locomo_driver_unregister);
static int __init locomo_init(void)
{
MODULE_DESCRIPTION("Sharp LoCoMo core driver");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>");
-
-EXPORT_SYMBOL(locomo_driver_register);
-EXPORT_SYMBOL(locomo_driver_unregister);
-EXPORT_SYMBOL(locomo_gpio_set_dir);
-EXPORT_SYMBOL(locomo_gpio_read_level);
-EXPORT_SYMBOL(locomo_gpio_read_output);
-EXPORT_SYMBOL(locomo_gpio_write);
-EXPORT_SYMBOL(locomo_m62332_senddata);
return __sa1111_pll_clock(sachip);
}
+EXPORT_SYMBOL(sa1111_pll_clock);
/**
* sa1111_select_audio_mode - select I2S or AC link mode
spin_unlock_irqrestore(&sachip->lock, flags);
}
+EXPORT_SYMBOL(sa1111_select_audio_mode);
/**
* sa1111_set_audio_rate - set the audio sample rate
return 0;
}
+EXPORT_SYMBOL(sa1111_set_audio_rate);
/**
* sa1111_get_audio_rate - get the audio sample rate
return __sa1111_pll_clock(sachip) / (256 * div);
}
+EXPORT_SYMBOL(sa1111_get_audio_rate);
void sa1111_set_io_dir(struct sa1111_dev *sadev,
unsigned int bits, unsigned int dir,
MODIFY_BITS(gpio + SA1111_GPIO_PCSDR, (bits >> 16) & 255, sleep_dir >> 16);
spin_unlock_irqrestore(&sachip->lock, flags);
}
+EXPORT_SYMBOL(sa1111_set_io_dir);
void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
{
MODIFY_BITS(gpio + SA1111_GPIO_PCDWR, (bits >> 16) & 255, v >> 16);
spin_unlock_irqrestore(&sachip->lock, flags);
}
+EXPORT_SYMBOL(sa1111_set_io);
void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
{
MODIFY_BITS(gpio + SA1111_GPIO_PCSSR, (bits >> 16) & 255, v >> 16);
spin_unlock_irqrestore(&sachip->lock, flags);
}
+EXPORT_SYMBOL(sa1111_set_sleep_io);
/*
* Individual device operations.
sa1111_writel(val | sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
spin_unlock_irqrestore(&sachip->lock, flags);
}
+EXPORT_SYMBOL(sa1111_enable_device);
/**
* sa1111_disable_device - disable an on-chip SA1111 function block
sa1111_writel(val & ~sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
spin_unlock_irqrestore(&sachip->lock, flags);
}
+EXPORT_SYMBOL(sa1111_disable_device);
/*
* SA1111 "Register Access Bus."
.suspend = sa1111_bus_suspend,
.resume = sa1111_bus_resume,
};
+EXPORT_SYMBOL(sa1111_bus_type);
int sa1111_driver_register(struct sa1111_driver *driver)
{
driver->drv.bus = &sa1111_bus_type;
return driver_register(&driver->drv);
}
+EXPORT_SYMBOL(sa1111_driver_register);
void sa1111_driver_unregister(struct sa1111_driver *driver)
{
driver_unregister(&driver->drv);
}
+EXPORT_SYMBOL(sa1111_driver_unregister);
static int __init sa1111_init(void)
{
MODULE_DESCRIPTION("Intel Corporation SA1111 core driver");
MODULE_LICENSE("GPL");
-
-EXPORT_SYMBOL(sa1111_select_audio_mode);
-EXPORT_SYMBOL(sa1111_set_audio_rate);
-EXPORT_SYMBOL(sa1111_get_audio_rate);
-EXPORT_SYMBOL(sa1111_set_io_dir);
-EXPORT_SYMBOL(sa1111_set_io);
-EXPORT_SYMBOL(sa1111_set_sleep_io);
-EXPORT_SYMBOL(sa1111_enable_device);
-EXPORT_SYMBOL(sa1111_disable_device);
-EXPORT_SYMBOL(sa1111_pll_clock);
-EXPORT_SYMBOL(sa1111_bus_type);
-EXPORT_SYMBOL(sa1111_driver_register);
-EXPORT_SYMBOL(sa1111_driver_unregister);
#include <linux/list.h>
#include <linux/io.h>
#include <linux/sysdev.h>
+#include <linux/device.h>
#include <linux/amba/bus.h>
#include <asm/mach/irq.h>
# CONFIG_SA1100_COLLIE is not set
# CONFIG_SA1100_H3100 is not set
CONFIG_SA1100_H3600=y
-CONFIG_SA1100_H3XXX=y
# CONFIG_SA1100_BADGE4 is not set
# CONFIG_SA1100_JORNADA720 is not set
# CONFIG_SA1100_HACKKIT is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc5
-# Wed Dec 12 16:11:27 2007
+# Linux kernel version: 2.6.31-rc6
+# Tue Aug 18 13:41:41 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-# CONFIG_GENERIC_GPIO is not set
-# CONFIG_GENERIC_TIME is not set
-# CONFIG_GENERIC_CLOCKEVENTS is not set
+CONFIG_GENERIC_GPIO=y
CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+# CONFIG_CLASSIC_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_GROUP_SCHED is not set
# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_PCI_QUIRKS=y
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_FREEZER is not set
#
# System Type
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
CONFIG_ARCH_IOP33X=y
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
# CONFIG_ARCH_KS8695 is not set
# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-CONFIG_IOP3XX_ATU=y
#
# IOP33x Implementation Options
#
CONFIG_ARCH_IQ80331=y
CONFIG_MACH_IQ80332=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
CONFIG_PLAT_IOP=y
#
CONFIG_CPU_XSCALE=y
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
CONFIG_CPU_CP15=y
#
# CONFIG_ARM_THUMB is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
# CONFIG_IWMMXT is not set
CONFIG_XSCALE_PMU=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_PCI_LEGACY=y
# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCI_STUB is not set
+# CONFIG_PCI_IOV is not set
# CONFIG_PCCARD is not set
#
# Kernel Features
#
-# CONFIG_TICK_ONESHOT is not set
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
# CONFIG_PREEMPT is not set
CONFIG_HZ=100
# CONFIG_AEABI is not set
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
#
# Boot options
#
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp cachepolicy=writealloc"
+CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp cachepolicy=writealloc iop3xx_init_atu=y"
# CONFIG_XIP_KERNEL is not set
# CONFIG_KEXEC is not set
+#
+# CPU Power Management
+#
+# CONFIG_CPU_IDLE is not set
+
#
# Floating point emulation
#
# Userspace binary formats
#
CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
CONFIG_BINFMT_AOUT=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_ARTHUR is not set
# Power management options
#
# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_NET=y
#
# CONFIG_XFRM_USER is not set
# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IPV6_SIT is not set
# CONFIG_IPV6_TUNNEL is not set
# CONFIG_IPV6_MULTIPLE_TABLES is not set
+# CONFIG_IPV6_MROUTE is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
+CONFIG_WIRELESS=y
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_OLD_REGULATORY is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_LIB80211 is not set
#
-# Wireless
+# CFG80211 needs to be enabled for MAC80211
#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
+CONFIG_MAC80211_DEFAULT_PS_VALUE=0
+# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_MTD_DEBUG is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
CONFIG_MTD_REDBOOT_PARTS_READONLY=y
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
#
# User Modules And Translation Layers
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0x0
-CONFIG_MTD_PHYSMAP_LEN=0x0
-CONFIG_MTD_PHYSMAP_BANKWIDTH=1
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_MTD_NAND is not set
# CONFIG_MTD_ONENAND is not set
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
#
# UBI - Unsorted block images
#
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_BLK_DEV_XIP is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
-# CONFIG_EEPROM_93CX6 is not set
# CONFIG_SGI_IOC4 is not set
# CONFIG_TIFM_CORE is not set
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_HP_ILO is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
+# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_BLK_DEV_SR is not set
CONFIG_CHR_DEV_SG=y
# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_CXGB3_ISCSI is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_MPT2SAS is not set
# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_LIBFC is not set
+# CONFIG_LIBFCOE is not set
+# CONFIG_FCOE is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
# CONFIG_ATA is not set
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
+CONFIG_MD_AUTODETECT=y
CONFIG_MD_LINEAR=y
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
# CONFIG_MD_RAID10 is not set
CONFIG_MD_RAID456=y
-# CONFIG_MD_RAID5_RESHAPE is not set
+CONFIG_MD_RAID6_PQ=y
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=y
#
# IEEE 1394 (FireWire) support
#
+
+#
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
+#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_VETH is not set
-# CONFIG_IP1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_NET_ETHERNET is not set
CONFIG_NETDEV_1000=y
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
CONFIG_E1000=y
-CONFIG_E1000_NAPI=y
-# CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
+# CONFIG_IGBVF is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
# CONFIG_SKY2 is not set
-# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
+# CONFIG_ATL1C is not set
+# CONFIG_JME is not set
CONFIG_NETDEV_10000=y
# CONFIG_CHELSIO_T1 is not set
+CONFIG_CHELSIO_T3_DEPENDS=y
# CONFIG_CHELSIO_T3 is not set
+# CONFIG_ENIC is not set
# CONFIG_IXGBE is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
+# CONFIG_VXGE is not set
# CONFIG_MYRI10GE is not set
# CONFIG_NETXEN_NIC is not set
# CONFIG_NIU is not set
+# CONFIG_MLX4_EN is not set
# CONFIG_MLX4_CORE is not set
# CONFIG_TEHUTI is not set
+# CONFIG_BNX2X is not set
+# CONFIG_QLGE is not set
+# CONFIG_SFC is not set
+# CONFIG_BE2NET is not set
# CONFIG_TR is not set
#
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
CONFIG_HW_RANDOM=y
-# CONFIG_NVRAM is not set
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
#
-# I2C Algorithms
+# I2C Hardware Bus support
#
-# CONFIG_I2C_ALGOBIT is not set
-# CONFIG_I2C_ALGOPCF is not set
-# CONFIG_I2C_ALGOPCA is not set
#
-# I2C Hardware Bus support
+# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
-# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_PIIX4 is not set
-CONFIG_I2C_IOP3XX=y
# CONFIG_I2C_NFORCE2 is not set
-# CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PROSAVAGE is not set
-# CONFIG_I2C_SAVAGE4 is not set
-# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
-# CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+CONFIG_I2C_IOP3XX=y
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Graphics adapter I2C/DDC channel drivers
+#
# CONFIG_I2C_VOODOO3 is not set
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
#
# Miscellaneous I2C Chip support
#
-# CONFIG_SENSORS_DS1337 is not set
-# CONFIG_SENSORS_DS1374 is not set
# CONFIG_DS1682 is not set
-# CONFIG_EEPROM_LEGACY is not set
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_PCF8591 is not set
-# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
#
-# SPI support
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+# CONFIG_GPIO_BT8XX is not set
+
+#
+# SPI GPIO expanders:
#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1029 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_MAX6650 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_DME1737 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83792D is not set
# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
#
# Sonics Silicon Backplane
#
-CONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-CONFIG_DAB=y
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-
-#
-# Sound
-#
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
+# CONFIG_HID_PID is not set
+
+#
+# Special HID drivers
+#
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
# CONFIG_USB is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# Enable Host or Gadget support to see Inventra options
#
#
-# USB Gadget Support
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
#
# CONFIG_USB_GADGET is not set
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_UWB is not set
# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_NEW_LEDS is not set
CONFIG_RTC_LIB=y
# CONFIG_RTC_CLASS is not set
# DMA Clients
#
CONFIG_NET_DMA=y
+# CONFIG_ASYNC_TX_DMA is not set
+# CONFIG_DMATEST is not set
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
#
# File systems
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
-# CONFIG_EXT4DEV_FS is not set
+# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
#
# CD-ROM/DVD Filesystems
#
#
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS2_FS is not set
CONFIG_CRAMFS=y
+# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
-# CONFIG_NFS_DIRECTIO is not set
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-# CONFIG_NFSD_TCP is not set
-CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_SUNRPC_BIND34 is not set
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_SYSV68_PARTITION is not set
# CONFIG_NLS is not set
# CONFIG_DLM is not set
-CONFIG_INSTRUMENTATION=y
-# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
#
# Kernel hacking
# CONFIG_PRINTK_TIME is not set
CONFIG_ENABLE_WARN_DEPRECATED=y
CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_FORCED_INLINING is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+CONFIG_FTRACE=y
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_BOOT_TRACER is not set
+CONFIG_BRANCH_PROFILE_NONE=y
+# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
+# CONFIG_PROFILE_ALL_BRANCHES is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
CONFIG_DEBUG_USER=y
# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_DEBUG_LL=y
# CONFIG_DEBUG_ICEDCC is not set
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
# CONFIG_SECURITY_FILE_CAPABILITIES is not set
CONFIG_XOR_BLOCKS=y
CONFIG_ASYNC_CORE=y
CONFIG_ASYNC_MEMCPY=y
CONFIG_ASYNC_XOR=y
-# CONFIG_CRYPTO is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
+# CONFIG_BINARY_PRINTF is not set
#
# Library routines
#
+CONFIG_GENERIC_FIND_LAST_BIT=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC_ITU_T is not set
# CONFIG_CRC32 is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
-CONFIG_PLIST=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.24-rc5
-# Fri Dec 21 11:06:19 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_LOCK_KERNEL=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-# CONFIG_CPU_PXA320 is not set
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-# CONFIG_MACH_ZYLONITE is not set
-CONFIG_MACH_LITTLETON=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-CONFIG_PXA_SSP=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-CONFIG_TICK_ONESHOT=y
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_PREEMPT=y
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=64M"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# CPU Frequency scaling
-#
-# CONFIG_CPU_FREQ is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
-# CONFIG_XFRM_SUB_POLICY is not set
-# CONFIG_XFRM_MIGRATE is not set
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-# CONFIG_IP_PNP_DHCP is not set
-# CONFIG_IP_PNP_BOOTP is not set
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-CONFIG_INET_XFRM_MODE_TRANSPORT=y
-CONFIG_INET_XFRM_MODE_TUNNEL=y
-CONFIG_INET_XFRM_MODE_BEET=y
-# CONFIG_INET_LRO is not set
-CONFIG_INET_DIAG=y
-CONFIG_INET_TCP_DIAG=y
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-# CONFIG_STANDALONE is not set
-# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-CONFIG_FW_LOADER=y
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-# CONFIG_WATCHDOG is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-CONFIG_FONT_8x16=y
-# CONFIG_FONT_6x11 is not set
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-# CONFIG_DNOTIFY is not set
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_WARN_DEPRECATED=y
-CONFIG_ENABLE_MUST_CHECK=y
-CONFIG_MAGIC_SYSRQ=y
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_SLAB is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-CONFIG_FRAME_POINTER=y
-CONFIG_FORCED_INLINING=y
-# CONFIG_BOOT_PRINTK_DELAY is not set
-# CONFIG_RCU_TORTURE_TEST is not set
-# CONFIG_FAULT_INJECTION is not set
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_ERRORS=y
-CONFIG_DEBUG_LL=y
-# CONFIG_DEBUG_ICEDCC is not set
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-CONFIG_CRYPTO_HW=y
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-CONFIG_CRC_CCITT=y
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc1
+# Mon Jul 13 22:48:49 2009
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+# CONFIG_CLASSIC_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_GROUP_SCHED=y
+CONFIG_FAIR_GROUP_SCHED=y
+# CONFIG_RT_GROUP_SCHED is not set
+CONFIG_USER_SCHED=y
+# CONFIG_CGROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_STRIP_ASM_SYMS is not set
+CONFIG_COMPAT_BRK=y
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+# CONFIG_MODULE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBDAF=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+
+#
+# Supported PXA3xx Processor Variants
+#
+CONFIG_CPU_PXA300=y
+CONFIG_CPU_PXA310=y
+CONFIG_CPU_PXA320=y
+CONFIG_CPU_PXA930=y
+CONFIG_CPU_PXA935=y
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+CONFIG_MACH_ZYLONITE=y
+CONFIG_MACH_LITTLETON=y
+CONFIG_MACH_TAVOREVB=y
+CONFIG_MACH_SAAR=y
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_PXA3xx=y
+CONFIG_PXA_SSP=y
+CONFIG_PXA_HAVE_BOARD_IRQS=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSC3=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_IO_36=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_OUTER_CACHE=y
+CONFIG_CACHE_XSC3L2=y
+CONFIG_IWMMXT=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PREEMPT=y
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=64M debug"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+# CONFIG_IP_PNP_DHCP is not set
+# CONFIG_IP_PNP_BOOTP is not set
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_H1900 is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_SHARPSL is not set
+CONFIG_MTD_NAND_PXA3xx=y
+CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
+# CONFIG_MTD_NAND_NANDSIM is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+CONFIG_MTD_ONENAND=y
+CONFIG_MTD_ONENAND_VERIFY_WRITE=y
+CONFIG_MTD_ONENAND_GENERIC=y
+# CONFIG_MTD_ONENAND_OTP is not set
+# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
+# CONFIG_MTD_ONENAND_SIM is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+# CONFIG_BLK_DEV_XIP is not set
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+CONFIG_KEYBOARD_PXA27x=y
+CONFIG_KEYBOARD_PXA930_ROTARY=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+CONFIG_MOUSE_PXA930_TRKBALL=y
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+CONFIG_TOUCHSCREEN_DA9034=y
+# CONFIG_TOUCHSCREEN_EETI is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_CHARDEV is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+
+#
+# I2C Algorithms
+#
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_ALGOPCF is not set
+# CONFIG_I2C_ALGOPCA is not set
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=y
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_PXA2XX=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+CONFIG_GPIO_MAX732X=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_GPIO_PCF857X=y
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+CONFIG_GPIO_MAX7301=y
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_SUPPLY_DEBUG=y
+CONFIG_PDA_POWER=y
+# CONFIG_BATTERY_DS2760 is not set
+# CONFIG_BATTERY_BQ27x00 is not set
+CONFIG_BATTERY_DA9030=y
+# CONFIG_BATTERY_MAX17040 is not set
+# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+CONFIG_PMIC_DA903X=y
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_PXA=y
+# CONFIG_FB_PXA_OVERLAY is not set
+# CONFIG_FB_PXA_SMARTPANEL is not set
+# CONFIG_FB_PXA_PARAMETERS is not set
+# CONFIG_FB_MBX is not set
+# CONFIG_FB_W100 is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+CONFIG_LCD_TDO24M=y
+# CONFIG_LCD_VGG2432A4 is not set
+# CONFIG_LCD_PLATFORM is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_BACKLIGHT_DA903X=y
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
+CONFIG_FONTS=y
+# CONFIG_FONT_8x8 is not set
+# CONFIG_FONT_8x16 is not set
+CONFIG_FONT_6x11=y
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+# CONFIG_FONT_MINI_4x6 is not set
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_PXA=y
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_SPI is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=m
+
+#
+# LED drivers
+#
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+CONFIG_LEDS_DA903X=m
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_GPIO=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+CONFIG_RTC_LIB=y
+# CONFIG_RTC_CLASS is not set
+# CONFIG_DMADEVICES is not set
+# CONFIG_AUXDISPLAY is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_DA903X=y
+# CONFIG_REGULATOR_LP3971 is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+# CONFIG_EXT2_FS is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
+CONFIG_DNOTIFY=y
+# CONFIG_INOTIFY is not set
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+# CONFIG_TMPFS is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RTIME=y
+CONFIG_JFFS2_RUBIN=y
+# CONFIG_JFFS2_CMODE_NONE is not set
+CONFIG_JFFS2_CMODE_PRIORITY=y
+# CONFIG_JFFS2_CMODE_SIZE is not set
+# CONFIG_JFFS2_CMODE_FAVOURLZO is not set
+# CONFIG_CRAMFS is not set
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="iso8859-1"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+# CONFIG_NLS_UTF8 is not set
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DETECT_SOFTLOCKUP=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=1
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+CONFIG_DEBUG_PREEMPT=y
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+CONFIG_DEBUG_SPINLOCK=y
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+CONFIG_DEBUG_SPINLOCK_SLEEP=y
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_KMEMCHECK is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+CONFIG_CRYPTO_WORKQUEUE=y
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.31-rc6
+# Thu Aug 20 09:02:37 2009
+#
+CONFIG_ARM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_ARCH_MTD_XIP=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=".xcep-itech"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+CONFIG_BSD_PROCESS_ACCT=y
+# CONFIG_BSD_PROCESS_ACCT_V3 is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_RELAY is not set
+# CONFIG_NAMESPACES is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+CONFIG_EMBEDDED=y
+# CONFIG_UID16 is not set
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+# CONFIG_SHMEM is not set
+CONFIG_AIO=y
+
+#
+# Performance Counters
+#
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_STRIP_ASM_SYMS=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+# CONFIG_SLUB is not set
+CONFIG_SLOB=y
+# CONFIG_PROFILING is not set
+CONFIG_TRACEPOINTS=y
+CONFIG_MARKERS=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_KPROBES=y
+CONFIG_KRETPROBES=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLOCK is not set
+# CONFIG_FREEZER is not set
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_PNX4008 is not set
+CONFIG_ARCH_PXA=y
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+# CONFIG_ARCH_S3C2410 is not set
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+
+#
+# Intel PXA2xx/PXA3xx Implementations
+#
+# CONFIG_ARCH_GUMSTIX is not set
+# CONFIG_MACH_INTELMOTE2 is not set
+# CONFIG_MACH_STARGATE2 is not set
+# CONFIG_ARCH_LUBBOCK is not set
+# CONFIG_MACH_LOGICPD_PXA270 is not set
+# CONFIG_MACH_MAINSTONE is not set
+# CONFIG_MACH_MP900C is not set
+# CONFIG_ARCH_PXA_IDP is not set
+# CONFIG_PXA_SHARPSL is not set
+# CONFIG_ARCH_VIPER is not set
+# CONFIG_ARCH_PXA_ESERIES is not set
+# CONFIG_TRIZEPS_PXA is not set
+# CONFIG_MACH_H5000 is not set
+# CONFIG_MACH_EM_X270 is not set
+# CONFIG_MACH_EXEDA is not set
+# CONFIG_MACH_COLIBRI is not set
+# CONFIG_MACH_COLIBRI300 is not set
+# CONFIG_MACH_COLIBRI320 is not set
+# CONFIG_MACH_ZYLONITE is not set
+# CONFIG_MACH_LITTLETON is not set
+# CONFIG_MACH_TAVOREVB is not set
+# CONFIG_MACH_SAAR is not set
+# CONFIG_MACH_ARMCORE is not set
+# CONFIG_MACH_CM_X300 is not set
+# CONFIG_MACH_H4700 is not set
+# CONFIG_MACH_MAGICIAN is not set
+# CONFIG_MACH_HIMALAYA is not set
+# CONFIG_MACH_MIOA701 is not set
+# CONFIG_MACH_PCM027 is not set
+# CONFIG_ARCH_PXA_PALM is not set
+# CONFIG_MACH_CSB726 is not set
+# CONFIG_PXA_EZX is not set
+CONFIG_MACH_XCEP=y
+CONFIG_PXA25x=y
+CONFIG_PXA_SSP=y
+CONFIG_PLAT_PXA=y
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_XSCALE=y
+CONFIG_CPU_32v5=y
+CONFIG_CPU_ABRT_EV5T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+CONFIG_IWMMXT=y
+CONFIG_XSCALE_PMU=y
+CONFIG_COMMON_CLKDEV=y
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=100
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_UACCESS_WITH_MEMCPY is not set
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_CMDLINE="root=mtd4 rootfstype=jffs2 ro console=ttyS0,115200"
+# CONFIG_XIP_KERNEL is not set
+# CONFIG_KEXEC is not set
+
+#
+# CPU Power Management
+#
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_IDLE is not set
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+CONFIG_FPE_NWFPE=y
+# CONFIG_FPE_NWFPE_XP is not set
+# CONFIG_FPE_FASTFPE is not set
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+# CONFIG_BINFMT_AOUT is not set
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=m
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=y
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_LRO=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_TCPPROBE is not set
+# CONFIG_NET_DROP_MONITOR is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+# CONFIG_WIRELESS is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_CFI_INTELEXT=y
+# CONFIG_MTD_CFI_AMDSTD is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+# CONFIG_MTD_XIP is not set
+
+#
+# Mapping drivers for chip access
+#
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_MTD_PHYSMAP_COMPAT is not set
+CONFIG_MTD_PXA2XX=y
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+# CONFIG_MTD_LPDDR is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
+
+#
+# SCSI device support
+#
+# CONFIG_SCSI_DMA is not set
+# CONFIG_SCSI_NETLINK is not set
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+CONFIG_SMC91X=y
+# CONFIG_DM9000 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set
+
+#
+# Input Device Drivers
+#
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+# CONFIG_VT_HW_CONSOLE_BINDING is not set
+# CONFIG_DEVKMEM is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_PXA=y
+CONFIG_SERIAL_PXA_CONSOLE=y
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_R3964 is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=m
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_DESIGNWARE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_PXA=m
+# CONFIG_I2C_PXA_SLAVE is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_TSL2550 is not set
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+# CONFIG_SPI is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+# CONFIG_GPIO_SYSFS is not set
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=m
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+CONFIG_SENSORS_ADM1021=m
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+CONFIG_SENSORS_MAX6650=m
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_THERMAL is not set
+# CONFIG_WATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_MEDIA_SUPPORT is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+# CONFIG_SOUND is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_NEW_LEDS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=m
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_SA1100=m
+# CONFIG_RTC_DRV_PXA is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_FILE_LOCKING=y
+# CONFIG_FSNOTIFY is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+# CONFIG_QUOTA is not set
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+# CONFIG_CONFIGFS_FS is not set
+CONFIG_MISC_FILESYSTEMS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+CONFIG_JFFS2_FS_WBUF_VERIFY=y
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=m
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=m
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+CONFIG_NLS=m
+CONFIG_NLS_DEFAULT="utf8"
+# CONFIG_NLS_CODEPAGE_437 is not set
+# CONFIG_NLS_CODEPAGE_737 is not set
+# CONFIG_NLS_CODEPAGE_775 is not set
+# CONFIG_NLS_CODEPAGE_850 is not set
+# CONFIG_NLS_CODEPAGE_852 is not set
+# CONFIG_NLS_CODEPAGE_855 is not set
+# CONFIG_NLS_CODEPAGE_857 is not set
+# CONFIG_NLS_CODEPAGE_860 is not set
+# CONFIG_NLS_CODEPAGE_861 is not set
+# CONFIG_NLS_CODEPAGE_862 is not set
+# CONFIG_NLS_CODEPAGE_863 is not set
+# CONFIG_NLS_CODEPAGE_864 is not set
+# CONFIG_NLS_CODEPAGE_865 is not set
+# CONFIG_NLS_CODEPAGE_866 is not set
+# CONFIG_NLS_CODEPAGE_869 is not set
+# CONFIG_NLS_CODEPAGE_936 is not set
+# CONFIG_NLS_CODEPAGE_950 is not set
+# CONFIG_NLS_CODEPAGE_932 is not set
+# CONFIG_NLS_CODEPAGE_949 is not set
+# CONFIG_NLS_CODEPAGE_874 is not set
+# CONFIG_NLS_ISO8859_8 is not set
+# CONFIG_NLS_CODEPAGE_1250 is not set
+# CONFIG_NLS_CODEPAGE_1251 is not set
+# CONFIG_NLS_ASCII is not set
+# CONFIG_NLS_ISO8859_1 is not set
+# CONFIG_NLS_ISO8859_2 is not set
+# CONFIG_NLS_ISO8859_3 is not set
+# CONFIG_NLS_ISO8859_4 is not set
+# CONFIG_NLS_ISO8859_5 is not set
+# CONFIG_NLS_ISO8859_6 is not set
+# CONFIG_NLS_ISO8859_7 is not set
+# CONFIG_NLS_ISO8859_9 is not set
+# CONFIG_NLS_ISO8859_13 is not set
+# CONFIG_NLS_ISO8859_14 is not set
+# CONFIG_NLS_ISO8859_15 is not set
+# CONFIG_NLS_KOI8_R is not set
+# CONFIG_NLS_KOI8_U is not set
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+# CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+CONFIG_FRAME_POINTER=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_KPROBES_SANITY_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+# CONFIG_FTRACE is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_ARM_UNWIND is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+# CONFIG_CRYPTO_FIPS is not set
+CONFIG_CRYPTO_ALGAPI=m
+CONFIG_CRYPTO_ALGAPI2=m
+CONFIG_CRYPTO_HASH=m
+CONFIG_CRYPTO_HASH2=m
+# CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_CRYPTD is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Authenticated Encryption with Associated Data
+#
+# CONFIG_CRYPTO_CCM is not set
+# CONFIG_CRYPTO_GCM is not set
+# CONFIG_CRYPTO_SEQIV is not set
+
+#
+# Block modes
+#
+# CONFIG_CRYPTO_CBC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_CTS is not set
+# CONFIG_CRYPTO_ECB is not set
+# CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_PCBC is not set
+# CONFIG_CRYPTO_XTS is not set
+
+#
+# Hash modes
+#
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_MD4 is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_RMD128 is not set
+# CONFIG_CRYPTO_RMD160 is not set
+# CONFIG_CRYPTO_RMD256 is not set
+# CONFIG_CRYPTO_RMD320 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_WP512 is not set
+
+#
+# Ciphers
+#
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_SALSA20 is not set
+# CONFIG_CRYPTO_SEED is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+
+#
+# Compression
+#
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZLIB is not set
+# CONFIG_CRYPTO_LZO is not set
+
+#
+# Random Number Generation
+#
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_T10DIF is not set
+# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC32=y
+# CONFIG_CRC7 is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y
+++ /dev/null
-#
-# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23
-# Tue Oct 23 13:33:20 2007
-#
-CONFIG_ARM=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_TIME=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_LOCKDEP_SUPPORT=y
-CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_HWEIGHT=y
-CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_ZONE_DMA=y
-CONFIG_ARCH_MTD_XIP=y
-CONFIG_VECTORS_BASE=0xffff0000
-CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
-
-#
-# General setup
-#
-CONFIG_EXPERIMENTAL=y
-CONFIG_BROKEN_ON_SMP=y
-CONFIG_INIT_ENV_ARG_LIMIT=32
-CONFIG_LOCALVERSION=""
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_SWAP=y
-CONFIG_SYSVIPC=y
-CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
-# CONFIG_BSD_PROCESS_ACCT is not set
-# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_AUDIT is not set
-# CONFIG_IKCONFIG is not set
-CONFIG_LOG_BUF_SHIFT=18
-# CONFIG_CGROUPS is not set
-CONFIG_FAIR_GROUP_SCHED=y
-CONFIG_FAIR_USER_SCHED=y
-# CONFIG_FAIR_CGROUP_SCHED is not set
-CONFIG_SYSFS_DEPRECATED=y
-# CONFIG_RELAY is not set
-# CONFIG_BLK_DEV_INITRD is not set
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
-CONFIG_UID16=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_EXTRA_PASS is not set
-CONFIG_HOTPLUG=y
-CONFIG_PRINTK=y
-CONFIG_BUG=y
-CONFIG_ELF_CORE=y
-CONFIG_BASE_FULL=y
-CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
-CONFIG_EPOLL=y
-CONFIG_SIGNALFD=y
-CONFIG_EVENTFD=y
-CONFIG_SHMEM=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLUB_DEBUG=y
-# CONFIG_SLAB is not set
-CONFIG_SLUB=y
-# CONFIG_SLOB is not set
-CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
-CONFIG_BASE_SMALL=0
-CONFIG_MODULES=y
-# CONFIG_MODULE_UNLOAD is not set
-# CONFIG_MODVERSIONS is not set
-# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
-CONFIG_BLOCK=y
-# CONFIG_LBD is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
-# CONFIG_BLK_DEV_BSG is not set
-
-#
-# IO Schedulers
-#
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_DEFAULT_AS is not set
-# CONFIG_DEFAULT_DEADLINE is not set
-CONFIG_DEFAULT_CFQ=y
-# CONFIG_DEFAULT_NOOP is not set
-CONFIG_DEFAULT_IOSCHED="cfq"
-
-#
-# System Type
-#
-# CONFIG_ARCH_AAEC2000 is not set
-# CONFIG_ARCH_INTEGRATOR is not set
-# CONFIG_ARCH_REALVIEW is not set
-# CONFIG_ARCH_VERSATILE is not set
-# CONFIG_ARCH_AT91 is not set
-# CONFIG_ARCH_CLPS7500 is not set
-# CONFIG_ARCH_CLPS711X is not set
-# CONFIG_ARCH_CO285 is not set
-# CONFIG_ARCH_EBSA110 is not set
-# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_FOOTBRIDGE is not set
-# CONFIG_ARCH_NETX is not set
-# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP13XX is not set
-# CONFIG_ARCH_IOP32X is not set
-# CONFIG_ARCH_IOP33X is not set
-# CONFIG_ARCH_IXP23XX is not set
-# CONFIG_ARCH_IXP2000 is not set
-# CONFIG_ARCH_IXP4XX is not set
-# CONFIG_ARCH_L7200 is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
-# CONFIG_ARCH_MXC is not set
-# CONFIG_ARCH_PNX4008 is not set
-CONFIG_ARCH_PXA=y
-# CONFIG_ARCH_RPC is not set
-# CONFIG_ARCH_SA1100 is not set
-# CONFIG_ARCH_S3C2410 is not set
-# CONFIG_ARCH_SHARK is not set
-# CONFIG_ARCH_LH7A40X is not set
-# CONFIG_ARCH_DAVINCI is not set
-# CONFIG_ARCH_OMAP is not set
-
-#
-# Intel PXA2xx/PXA3xx Implementations
-#
-
-#
-# Supported PXA3xx Processor Variants
-#
-CONFIG_CPU_PXA300=y
-CONFIG_CPU_PXA310=y
-CONFIG_CPU_PXA320=y
-# CONFIG_ARCH_LUBBOCK is not set
-# CONFIG_MACH_LOGICPD_PXA270 is not set
-# CONFIG_MACH_MAINSTONE is not set
-# CONFIG_ARCH_PXA_IDP is not set
-# CONFIG_PXA_SHARPSL is not set
-# CONFIG_MACH_TRIZEPS4 is not set
-# CONFIG_MACH_EM_X270 is not set
-CONFIG_MACH_ZYLONITE=y
-# CONFIG_MACH_ARMCORE is not set
-CONFIG_PXA3xx=y
-
-#
-# Boot options
-#
-
-#
-# Power management
-#
-
-#
-# Processor Type
-#
-CONFIG_CPU_32=y
-CONFIG_CPU_XSC3=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-CONFIG_IO_36=y
-
-#
-# Processor Features
-#
-# CONFIG_ARM_THUMB is not set
-# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_CPU_BPREDICT_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
-CONFIG_IWMMXT=y
-
-#
-# Bus support
-#
-# CONFIG_PCI_SYSCALL is not set
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-# CONFIG_PCCARD is not set
-
-#
-# Kernel Features
-#
-# CONFIG_TICK_ONESHOT is not set
-# CONFIG_NO_HZ is not set
-# CONFIG_HIGH_RES_TIMERS is not set
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-# CONFIG_PREEMPT is not set
-CONFIG_HZ=100
-CONFIG_AEABI=y
-CONFIG_OABI_COMPAT=y
-# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
-CONFIG_SELECT_MEMORY_MODEL=y
-CONFIG_FLATMEM_MANUAL=y
-# CONFIG_DISCONTIGMEM_MANUAL is not set
-# CONFIG_SPARSEMEM_MANUAL is not set
-CONFIG_FLATMEM=y
-CONFIG_FLAT_NODE_MEM_MAP=y
-# CONFIG_SPARSEMEM_STATIC is not set
-# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4096
-# CONFIG_RESOURCES_64BIT is not set
-CONFIG_ZONE_DMA_FLAG=1
-CONFIG_BOUNCE=y
-CONFIG_VIRT_TO_BUS=y
-CONFIG_ALIGNMENT_TRAP=y
-
-#
-# Boot options
-#
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfs/rootfs/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,38400 mem=64M debug"
-# CONFIG_XIP_KERNEL is not set
-# CONFIG_KEXEC is not set
-
-#
-# Floating point emulation
-#
-
-#
-# At least one emulation must be selected
-#
-CONFIG_FPE_NWFPE=y
-# CONFIG_FPE_NWFPE_XP is not set
-# CONFIG_FPE_FASTFPE is not set
-
-#
-# Userspace binary formats
-#
-CONFIG_BINFMT_ELF=y
-# CONFIG_BINFMT_AOUT is not set
-# CONFIG_BINFMT_MISC is not set
-
-#
-# Power management options
-#
-# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
-
-#
-# Networking
-#
-CONFIG_NET=y
-
-#
-# Networking options
-#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-# CONFIG_IP_MULTICAST is not set
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_FIB_HASH=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_ARPD is not set
-# CONFIG_SYN_COOKIES is not set
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
-# CONFIG_NETWORK_SECMARK is not set
-# CONFIG_NETFILTER is not set
-# CONFIG_IP_DCCP is not set
-# CONFIG_IP_SCTP is not set
-# CONFIG_TIPC is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
-# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
-# CONFIG_CFG80211 is not set
-# CONFIG_WIRELESS_EXT is not set
-# CONFIG_MAC80211 is not set
-# CONFIG_IEEE80211 is not set
-# CONFIG_RFKILL is not set
-# CONFIG_NET_9P is not set
-
-#
-# Device Drivers
-#
-
-#
-# Generic Driver Options
-#
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_STANDALONE=y
-CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=y
-# CONFIG_SYS_HYPERVISOR is not set
-# CONFIG_CONNECTOR is not set
-# CONFIG_MTD is not set
-# CONFIG_PARPORT is not set
-# CONFIG_BLK_DEV is not set
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_IDE is not set
-
-#
-# SCSI device support
-#
-# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SCSI_NETLINK is not set
-# CONFIG_ATA is not set
-# CONFIG_MD is not set
-CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
-# CONFIG_DUMMY is not set
-# CONFIG_BONDING is not set
-# CONFIG_MACVLAN is not set
-# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
-# CONFIG_VETH is not set
-# CONFIG_PHYLIB is not set
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-# CONFIG_AX88796 is not set
-CONFIG_SMC91X=y
-# CONFIG_DM9000 is not set
-# CONFIG_SMC911X is not set
-# CONFIG_IBM_NEW_EMAC_ZMII is not set
-# CONFIG_IBM_NEW_EMAC_RGMII is not set
-# CONFIG_IBM_NEW_EMAC_TAH is not set
-# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
-# CONFIG_B44 is not set
-# CONFIG_NETDEV_1000 is not set
-# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
-# CONFIG_WAN is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
-# CONFIG_SHAPER is not set
-# CONFIG_NETCONSOLE is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_ISDN is not set
-
-#
-# Input device support
-#
-CONFIG_INPUT=y
-# CONFIG_INPUT_FF_MEMLESS is not set
-# CONFIG_INPUT_POLLDEV is not set
-
-#
-# Userland interfaces
-#
-CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
-# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
-
-#
-# Input Device Drivers
-#
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_INPUT_JOYSTICK is not set
-# CONFIG_INPUT_TABLET is not set
-# CONFIG_INPUT_TOUCHSCREEN is not set
-# CONFIG_INPUT_MISC is not set
-
-#
-# Hardware I/O ports
-#
-# CONFIG_SERIO is not set
-# CONFIG_GAMEPORT is not set
-
-#
-# Character devices
-#
-CONFIG_VT=y
-CONFIG_VT_CONSOLE=y
-CONFIG_HW_CONSOLE=y
-# CONFIG_VT_HW_CONSOLE_BINDING is not set
-# CONFIG_SERIAL_NONSTANDARD is not set
-
-#
-# Serial drivers
-#
-# CONFIG_SERIAL_8250 is not set
-
-#
-# Non-8250 serial port support
-#
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_SERIAL_CORE=y
-CONFIG_SERIAL_CORE_CONSOLE=y
-CONFIG_UNIX98_PTYS=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_IPMI_HANDLER is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_NVRAM is not set
-# CONFIG_R3964 is not set
-# CONFIG_RAW_DRIVER is not set
-# CONFIG_TCG_TPM is not set
-# CONFIG_I2C is not set
-
-#
-# SPI support
-#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
-# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-# CONFIG_HWMON is not set
-
-#
-# Sonics Silicon Backplane
-#
-CONFIG_SSB_POSSIBLE=y
-# CONFIG_SSB is not set
-
-#
-# Multifunction device drivers
-#
-# CONFIG_MFD_SM501 is not set
-
-#
-# Multimedia devices
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
-
-#
-# Graphics support
-#
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-CONFIG_FB=y
-# CONFIG_FIRMWARE_EDID is not set
-# CONFIG_FB_DDC is not set
-CONFIG_FB_CFB_FILLRECT=y
-CONFIG_FB_CFB_COPYAREA=y
-CONFIG_FB_CFB_IMAGEBLIT=y
-# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-# CONFIG_FB_SYS_FILLRECT is not set
-# CONFIG_FB_SYS_COPYAREA is not set
-# CONFIG_FB_SYS_IMAGEBLIT is not set
-# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
-# CONFIG_FB_SVGALIB is not set
-# CONFIG_FB_MACMODES is not set
-# CONFIG_FB_BACKLIGHT is not set
-# CONFIG_FB_MODE_HELPERS is not set
-# CONFIG_FB_TILEBLITTING is not set
-
-#
-# Frame buffer hardware drivers
-#
-# CONFIG_FB_S1D13XXX is not set
-CONFIG_FB_PXA=y
-# CONFIG_FB_PXA_PARAMETERS is not set
-# CONFIG_FB_MBX is not set
-# CONFIG_FB_VIRTUAL is not set
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
-
-#
-# Console display driver support
-#
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_DUMMY_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
-# CONFIG_FONT_8x16 is not set
-CONFIG_FONT_6x11=y
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
-CONFIG_LOGO=y
-CONFIG_LOGO_LINUX_MONO=y
-CONFIG_LOGO_LINUX_VGA16=y
-CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
-# CONFIG_SOUND is not set
-# CONFIG_HID_SUPPORT is not set
-# CONFIG_USB_SUPPORT is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
-CONFIG_RTC_LIB=y
-# CONFIG_RTC_CLASS is not set
-
-#
-# File systems
-#
-# CONFIG_EXT2_FS is not set
-# CONFIG_EXT3_FS is not set
-# CONFIG_EXT4DEV_FS is not set
-# CONFIG_REISERFS_FS is not set
-# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
-# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
-# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
-# CONFIG_INOTIFY is not set
-# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
-# CONFIG_AUTOFS_FS is not set
-# CONFIG_AUTOFS4_FS is not set
-# CONFIG_FUSE_FS is not set
-
-#
-# CD-ROM/DVD Filesystems
-#
-# CONFIG_ISO9660_FS is not set
-# CONFIG_UDF_FS is not set
-
-#
-# DOS/FAT/NT Filesystems
-#
-# CONFIG_MSDOS_FS is not set
-# CONFIG_VFAT_FS is not set
-# CONFIG_NTFS_FS is not set
-
-#
-# Pseudo filesystems
-#
-CONFIG_PROC_FS=y
-CONFIG_PROC_SYSCTL=y
-CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
-# CONFIG_ADFS_FS is not set
-# CONFIG_AFFS_FS is not set
-# CONFIG_HFS_FS is not set
-# CONFIG_HFSPLUS_FS is not set
-# CONFIG_BEFS_FS is not set
-# CONFIG_BFS_FS is not set
-# CONFIG_EFS_FS is not set
-# CONFIG_CRAMFS is not set
-# CONFIG_VXFS_FS is not set
-# CONFIG_HPFS_FS is not set
-# CONFIG_QNX4FS_FS is not set
-# CONFIG_SYSV_FS is not set
-# CONFIG_UFS_FS is not set
-CONFIG_NETWORK_FILESYSTEMS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_DIRECTIO=y
-# CONFIG_NFSD is not set
-CONFIG_ROOT_NFS=y
-CONFIG_LOCKD=y
-CONFIG_LOCKD_V4=y
-CONFIG_NFS_ACL_SUPPORT=y
-CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=y
-CONFIG_SUNRPC_GSS=y
-# CONFIG_SUNRPC_BIND34 is not set
-CONFIG_RPCSEC_GSS_KRB5=y
-# CONFIG_RPCSEC_GSS_SPKM3 is not set
-# CONFIG_SMB_FS is not set
-# CONFIG_CIFS is not set
-# CONFIG_NCP_FS is not set
-# CONFIG_CODA_FS is not set
-# CONFIG_AFS_FS is not set
-
-#
-# Partition Types
-#
-# CONFIG_PARTITION_ADVANCED is not set
-CONFIG_MSDOS_PARTITION=y
-# CONFIG_NLS is not set
-# CONFIG_DLM is not set
-# CONFIG_INSTRUMENTATION is not set
-
-#
-# Kernel hacking
-#
-# CONFIG_PRINTK_TIME is not set
-CONFIG_ENABLE_MUST_CHECK=y
-# CONFIG_MAGIC_SYSRQ is not set
-# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
-# CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
-# CONFIG_SLUB_DEBUG_ON is not set
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_FRAME_POINTER=y
-# CONFIG_SAMPLES is not set
-CONFIG_DEBUG_USER=y
-
-#
-# Security options
-#
-# CONFIG_KEYS is not set
-# CONFIG_SECURITY is not set
-# CONFIG_SECURITY_FILE_CAPABILITIES is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_MANAGER=y
-# CONFIG_CRYPTO_HMAC is not set
-# CONFIG_CRYPTO_XCBC is not set
-# CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
-CONFIG_CRYPTO_MD5=y
-# CONFIG_CRYPTO_SHA1 is not set
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
-# CONFIG_CRYPTO_WP512 is not set
-# CONFIG_CRYPTO_TGR192 is not set
-# CONFIG_CRYPTO_GF128MUL is not set
-# CONFIG_CRYPTO_ECB is not set
-CONFIG_CRYPTO_CBC=y
-# CONFIG_CRYPTO_PCBC is not set
-# CONFIG_CRYPTO_LRW is not set
-# CONFIG_CRYPTO_XTS is not set
-# CONFIG_CRYPTO_CRYPTD is not set
-CONFIG_CRYPTO_DES=y
-# CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
-# CONFIG_CRYPTO_TWOFISH is not set
-# CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
-# CONFIG_CRYPTO_CAST5 is not set
-# CONFIG_CRYPTO_CAST6 is not set
-# CONFIG_CRYPTO_TEA is not set
-# CONFIG_CRYPTO_ARC4 is not set
-# CONFIG_CRYPTO_KHAZAD is not set
-# CONFIG_CRYPTO_ANUBIS is not set
-# CONFIG_CRYPTO_SEED is not set
-# CONFIG_CRYPTO_DEFLATE is not set
-# CONFIG_CRYPTO_MICHAEL_MIC is not set
-# CONFIG_CRYPTO_CRC32C is not set
-# CONFIG_CRYPTO_CAMELLIA is not set
-# CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_AUTHENC is not set
-# CONFIG_CRYPTO_HW is not set
-
-#
-# Library routines
-#
-CONFIG_BITREVERSE=y
-# CONFIG_CRC_CCITT is not set
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
-CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
-CONFIG_PLIST=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAS_DMA=y
#ifdef __KERNEL__
+/*
+ * On ARM, ordinary assignment (str instruction) doesn't clear the local
+ * strex/ldrex monitor on some implementations. The reason we can use it for
+ * atomic_set() is the clrex or dummy strex done on every exception return.
+ */
#define atomic_read(v) ((v)->counter)
+#define atomic_set(v,i) (((v)->counter) = (i))
#if __LINUX_ARM_ARCH__ >= 6
/*
* ARMv6 UP and SMP safe atomic ops. We use load exclusive and
* store exclusive to ensure that these are atomic. We may loop
- * to ensure that the update happens. Writing to 'v->counter'
- * without using the following operations WILL break the atomic
- * nature of these ops.
+ * to ensure that the update happens.
*/
-static inline void atomic_set(atomic_t *v, int i)
-{
- unsigned long tmp;
-
- __asm__ __volatile__("@ atomic_set\n"
-"1: ldrex %0, [%1]\n"
-" strex %0, %2, [%1]\n"
-" teq %0, #0\n"
-" bne 1b"
- : "=&r" (tmp)
- : "r" (&v->counter), "r" (i)
- : "cc");
-}
-
static inline void atomic_add(int i, atomic_t *v)
{
unsigned long tmp;
#error SMP not supported on pre-ARMv6 CPUs
#endif
-#define atomic_set(v,i) (((v)->counter) = (i))
-
static inline int atomic_add_return(int i, atomic_t *v)
{
unsigned long flags;
#ifndef __ASMARM_CACHE_H
#define __ASMARM_CACHE_H
-#define L1_CACHE_SHIFT 5
+#define L1_CACHE_SHIFT CONFIG_ARM_L1_CACHE_SHIFT
#define L1_CACHE_BYTES (1 << L1_CACHE_SHIFT)
/*
return read_cpuid(CPUID_CACHETYPE);
}
+static inline unsigned int __attribute_const__ read_cpuid_tcmstatus(void)
+{
+ return read_cpuid(CPUID_TCM);
+}
+
/*
* Intel's XScale3 core supports some v6 features (supersections, L2)
* but advertises itself as v5 as it does not support the v6 ISA. For
#else
static inline int cpu_is_xsc3(void)
{
- if ((read_cpuid_id() & 0xffffe000) == 0x69056000)
+ unsigned int id;
+ id = read_cpuid_id() & 0xffffe000;
+ /* It covers both Intel ID and Marvell ID */
+ if ((id == 0x69056000) || (id == 0x56056000))
return 1;
return 0;
#endif
/*
- * Prefetch abort handler. If the CPU has an IFAR use that, otherwise
- * use the address of the aborted instruction
+ * Prefetch Abort Model
+ * ================
+ *
+ * We have the following to choose from:
+ * legacy - no IFSR, no IFAR
+ * v6 - ARMv6: IFSR, no IFAR
+ * v7 - ARMv7: IFSR and IFAR
*/
+
#undef CPU_PABORT_HANDLER
#undef MULTI_PABORT
-#ifdef CONFIG_CPU_PABRT_IFAR
+#ifdef CONFIG_CPU_PABRT_LEGACY
+# ifdef CPU_PABORT_HANDLER
+# define MULTI_PABORT 1
+# else
+# define CPU_PABORT_HANDLER legacy_pabort
+# endif
+#endif
+
+#ifdef CONFIG_CPU_PABRT_V6
# ifdef CPU_PABORT_HANDLER
# define MULTI_PABORT 1
# else
-# define CPU_PABORT_HANDLER(reg, insn) mrc p15, 0, reg, cr6, cr0, 2
+# define CPU_PABORT_HANDLER v6_pabort
# endif
#endif
-#ifdef CONFIG_CPU_PABRT_NOIFAR
+#ifdef CONFIG_CPU_PABRT_V7
# ifdef CPU_PABORT_HANDLER
# define MULTI_PABORT 1
# else
-# define CPU_PABORT_HANDLER(reg, insn) mov reg, insn
+# define CPU_PABORT_HANDLER v7_pabort
# endif
#endif
void *ptr;
};
+/* No support for p+q operations */
+static inline int
+iop_chan_pq_slot_count(size_t len, int src_cnt, int *slots_per_op)
+{
+ BUG();
+ return 0;
+}
+
+static inline void
+iop_desc_init_pq(struct iop_adma_desc_slot *desc, int src_cnt,
+ unsigned long flags)
+{
+ BUG();
+}
+
+static inline void
+iop_desc_set_pq_addr(struct iop_adma_desc_slot *desc, dma_addr_t *addr)
+{
+ BUG();
+}
+
+static inline void
+iop_desc_set_pq_src_addr(struct iop_adma_desc_slot *desc, int src_idx,
+ dma_addr_t addr, unsigned char coef)
+{
+ BUG();
+}
+
+static inline int
+iop_chan_pq_zero_sum_slot_count(size_t len, int src_cnt, int *slots_per_op)
+{
+ BUG();
+ return 0;
+}
+
+static inline void
+iop_desc_init_pq_zero_sum(struct iop_adma_desc_slot *desc, int src_cnt,
+ unsigned long flags)
+{
+ BUG();
+}
+
+static inline void
+iop_desc_set_pq_zero_sum_byte_count(struct iop_adma_desc_slot *desc, u32 len)
+{
+ BUG();
+}
+
+#define iop_desc_set_pq_zero_sum_src_addr iop_desc_set_pq_src_addr
+
+static inline void
+iop_desc_set_pq_zero_sum_addr(struct iop_adma_desc_slot *desc, int pq_idx,
+ dma_addr_t *src)
+{
+ BUG();
+}
+
static inline int iop_adma_get_max_xor(void)
{
return 32;
}
+static inline int iop_adma_get_max_pq(void)
+{
+ BUG();
+ return 0;
+}
+
static inline u32 iop_chan_get_current_descriptor(struct iop_adma_chan *chan)
{
int id = chan->device->id;
return slot_cnt;
}
+static inline int iop_desc_is_pq(struct iop_adma_desc_slot *desc)
+{
+ return 0;
+}
+
static inline u32 iop_desc_get_dest_addr(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan)
{
return 0;
}
+
+static inline u32 iop_desc_get_qdest_addr(struct iop_adma_desc_slot *desc,
+ struct iop_adma_chan *chan)
+{
+ BUG();
+ return 0;
+}
+
static inline u32 iop_desc_get_byte_count(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan)
{
hw_desc->src[0] = val;
}
-static inline int iop_desc_get_zero_result(struct iop_adma_desc_slot *desc)
+static inline enum sum_check_flags
+iop_desc_get_zero_result(struct iop_adma_desc_slot *desc)
{
struct iop3xx_desc_aau *hw_desc = desc->hw_desc;
struct iop3xx_aau_desc_ctrl desc_ctrl = hw_desc->desc_ctrl_field;
iop_paranoia(!(desc_ctrl.tx_complete && desc_ctrl.zero_result_en));
- return desc_ctrl.zero_result_err;
+ return desc_ctrl.zero_result_err << SUM_CHECK_P;
}
static inline void iop_chan_append(struct iop_adma_chan *chan)
* IOP3XX I/O and Mem space regions for PCI autoconfiguration
*/
#define IOP3XX_PCI_LOWER_MEM_PA 0x80000000
+#define IOP3XX_PCI_MEM_WINDOW_SIZE 0x08000000
#define IOP3XX_PCI_IO_WINDOW_SIZE 0x00010000
#define IOP3XX_PCI_LOWER_IO_PA 0x90000000
* @idx: pool index
* @unmap_src_cnt: number of xor sources
* @unmap_len: transaction bytecount
+ * @tx_list: list of descriptors that are associated with one operation
* @async_tx: support for the async_tx api
* @group_list: list of slots that make up a multi-descriptor transaction
* for example transfer lengths larger than the supported hw max
u16 idx;
u16 unmap_src_cnt;
size_t unmap_len;
+ struct list_head tx_list;
struct dma_async_tx_descriptor async_tx;
union {
u32 *xor_check_result;
u32 *crc32_result;
+ u32 *pq_check_result;
};
};
+++ /dev/null
-/*
- * arch/arm/include/asm/mach/mmc.h
- */
-#ifndef ASMARM_MACH_MMC_H
-#define ASMARM_MACH_MMC_H
-
-#include <linux/mmc/host.h>
-
-struct mmc_platform_data {
- unsigned int ocr_mask; /* available voltages */
- u32 (*translate_vdd)(struct device *, unsigned int);
- unsigned int (*status)(struct device *);
- int gpio_wp;
- int gpio_cd;
-};
-
-#endif
--- /dev/null
+/*
+ * ARM specific SMP header, this contains our implementation
+ * details.
+ */
+#ifndef __ASMARM_SMP_PLAT_H
+#define __ASMARM_SMP_PLAT_H
+
+#include <asm/cputype.h>
+
+/* all SMP configurations have the extended CPUID registers */
+static inline int tlb_ops_need_broadcast(void)
+{
+ return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
+}
+
+#endif
--- /dev/null
+/*
+ *
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ *
+ */
+#ifndef __ASMARM_TCM_H
+#define __ASMARM_TCM_H
+
+#ifndef CONFIG_HAVE_TCM
+#error "You should not be including tcm.h unless you have a TCM!"
+#endif
+
+#include <linux/compiler.h>
+
+/* Tag variables with this */
+#define __tcmdata __section(.tcm.data)
+/* Tag constants with this */
+#define __tcmconst __section(.tcm.rodata)
+/* Tag functions inside TCM called from outside TCM with this */
+#define __tcmfunc __attribute__((long_call)) __section(.tcm.text) noinline
+/* Tag function inside TCM called from inside TCM with this */
+#define __tcmlocalfunc __section(.tcm.text)
+
+void *tcm_alloc(size_t len);
+void tcm_free(void *addr, size_t len);
+
+#endif
#define ARM(x...)
#define THUMB(x...) x
+#ifdef __ASSEMBLY__
#define W(instr) instr.w
+#endif
#define BSYM(sym) sym + 1
#else /* !CONFIG_THUMB2_KERNEL */
#define ARM(x...) x
#define THUMB(x...)
+#ifdef __ASSEMBLY__
#define W(instr) instr
+#endif
#define BSYM(sym) sym
#endif /* CONFIG_THUMB2_KERNEL */
* Unimplemented (or alternatively implemented) syscalls
*/
#define __IGNORE_fadvise64_64 1
+#define __IGNORE_migrate_pages 1
#endif /* __KERNEL__ */
#endif /* __ASM_ARM_UNISTD_H */
obj-$(CONFIG_ARM_THUMBEE) += thumbee.o
obj-$(CONFIG_KGDB) += kgdb.o
obj-$(CONFIG_ARM_UNWIND) += unwind.o
+obj-$(CONFIG_HAVE_TCM) += tcm.o
obj-$(CONFIG_CRUNCH) += crunch.o crunch-bits.o
AFLAGS_crunch-bits.o := -Wa,-mcpu=ep9312
@
@ r0 - instruction
@
+#ifndef CONFIG_THUMB2_KERNEL
ldr r0, [r2, #-4]
+#else
+ ldrh r0, [r2, #-2] @ Thumb instruction at LR - 2
+ and r9, r0, #0xf800
+ cmp r9, #0xe800 @ 32-bit instruction if xx >= 0
+ ldrhhs r9, [r2] @ bottom 16 bits
+ orrhs r0, r9, r0, lsl #16
+#endif
adr r9, BSYM(1f)
bl call_fpe
tst r3, #PSR_I_BIT
biceq r9, r9, #PSR_I_BIT
- @
- @ set args, then call main handler
- @
- @ r0 - address of faulting instruction
- @ r1 - pointer to registers on stack
- @
-#ifdef MULTI_PABORT
mov r0, r2 @ pass address of aborted instruction.
+#ifdef MULTI_PABORT
ldr r4, .LCprocfns
mov lr, pc
ldr pc, [r4, #PROCESSOR_PABT_FUNC]
#else
- CPU_PABORT_HANDLER(r0, r2)
+ bl CPU_PABORT_HANDLER
#endif
msr cpsr_c, r9 @ Maybe enable interrupts
- mov r1, sp @ regs
+ mov r2, sp @ regs
bl do_PrefetchAbort @ call abort handler
@
.word no_fp
.previous
-no_fp: mov pc, lr
+ENTRY(no_fp)
+ mov pc, lr
+ENDPROC(no_fp)
__und_usr_unknown:
enable_irq
__pabt_usr:
usr_entry
-#ifdef MULTI_PABORT
mov r0, r2 @ pass address of aborted instruction.
+#ifdef MULTI_PABORT
ldr r4, .LCprocfns
mov lr, pc
ldr pc, [r4, #PROCESSOR_PABT_FUNC]
#else
- CPU_PABORT_HANDLER(r0, r2)
+ bl CPU_PABORT_HANDLER
#endif
enable_irq @ Enable interrupts
- mov r1, sp @ regs
+ mov r2, sp @ regs
bl do_PrefetchAbort @ call abort handler
UNWIND(.fnend )
/* fall through */
#ifdef CONFIG_MMU
ldr r6, [r2, #TI_CPU_DOMAIN]
#endif
-#if __LINUX_ARM_ARCH__ >= 6
-#ifdef CONFIG_CPU_32v6K
- clrex
-#else
- strex r5, r4, [ip] @ Clear exclusive monitor
-#endif
-#endif
#if defined(CONFIG_HAS_TLS_REG)
mcr p15, 0, r3, c13, c0, 3 @ set TLS register
#elif !defined(CONFIG_TLS_REG_EMUL)
cmp r0, r2
bne gnu_trace
ldmia sp!, {r0-r3, ip, lr}
- bx ip
+ mov pc, ip
gnu_trace:
ldr r1, [sp, #20] @ lr of instrumented routine
mov lr, pc
mov pc, r2
ldmia sp!, {r0-r3, ip, lr}
- bx ip
+ mov pc, ip
ENTRY(mcount)
stmdb sp!, {r0-r3, lr}
#endif
ENDPROC(sys_mmap2)
-ENTRY(pabort_ifar)
- mrc p15, 0, r0, cr6, cr0, 2
-ENTRY(pabort_noifar)
- mov pc, lr
-ENDPROC(pabort_ifar)
-ENDPROC(pabort_noifar)
-
#ifdef CONFIG_OABI_COMPAT
/*
#ifndef CONFIG_THUMB2_KERNEL
.macro svc_exit, rpsr
msr spsr_cxsf, \rpsr
+#if defined(CONFIG_CPU_32v6K)
+ clrex @ clear the exclusive monitor
ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
+#elif defined (CONFIG_CPU_V6)
+ ldr r0, [sp]
+ strex r1, r2, [sp] @ clear the exclusive monitor
+ ldmib sp, {r1 - pc}^ @ load r1 - pc, cpsr
+#else
+ ldmia sp, {r0 - pc}^ @ load r0 - pc, cpsr
+#endif
.endm
.macro restore_user_regs, fast = 0, offset = 0
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
ldr lr, [sp, #\offset + S_PC]! @ get pc
msr spsr_cxsf, r1 @ save in spsr_svc
+#if defined(CONFIG_CPU_32v6K)
+ clrex @ clear the exclusive monitor
+#elif defined (CONFIG_CPU_V6)
+ strex r1, r2, [sp] @ clear the exclusive monitor
+#endif
.if \fast
ldmdb sp, {r1 - lr}^ @ get calling r1 - lr
.else
.endm
#else /* CONFIG_THUMB2_KERNEL */
.macro svc_exit, rpsr
+ clrex @ clear the exclusive monitor
ldr r0, [sp, #S_SP] @ top of the stack
ldr r1, [sp, #S_PC] @ return address
tst r0, #4 @ orig stack 8-byte aligned?
.endm
.macro restore_user_regs, fast = 0, offset = 0
+ clrex @ clear the exclusive monitor
mov r2, sp
load_user_sp_lr r2, r3, \offset + S_SP @ calling sp, lr
ldr r1, [sp, #\offset + S_PSR] @ get calling cpsr
#define ATAG_CORE 0x54410001
#define ATAG_CORE_SIZE ((2*4 + 3*4) >> 2)
+#define ATAG_CORE_SIZE_EMPTY ((2*4) >> 2)
.align 2
.type __switch_data, %object
bne 1f
ldr r5, [r2, #0] @ is first tag ATAG_CORE?
- subs r5, r5, #ATAG_CORE_SIZE
+ cmp r5, #ATAG_CORE_SIZE
+ cmpne r5, #ATAG_CORE_SIZE_EMPTY
bne 1f
ldr r5, [r2, #4]
ldr r6, =ATAG_CORE
#include <linux/kernel.h>
#include <linux/kprobes.h>
#include <linux/module.h>
+#include <linux/stop_machine.h>
#include <linux/stringify.h>
#include <asm/traps.h>
#include <asm/cacheflush.h>
flush_insns(p->addr, 1);
}
+/*
+ * The actual disarming is done here on each CPU and synchronized using
+ * stop_machine. This synchronization is necessary on SMP to avoid removing
+ * a probe between the moment the 'Undefined Instruction' exception is raised
+ * and the moment the exception handler reads the faulting instruction from
+ * memory.
+ */
+int __kprobes __arch_disarm_kprobe(void *p)
+{
+ struct kprobe *kp = p;
+ *kp->addr = kp->opcode;
+ flush_insns(kp->addr, 1);
+ return 0;
+}
+
void __kprobes arch_disarm_kprobe(struct kprobe *p)
{
- *p->addr = p->opcode;
- flush_insns(p->addr, 1);
+ stop_machine(__arch_disarm_kprobe, p, &cpu_online_map);
}
void __kprobes arch_remove_kprobe(struct kprobe *p)
#include "compat.h"
#include "atags.h"
+#include "tcm.h"
#ifndef MEM_SIZE
#define MEM_SIZE (16*1024*1024)
#endif
cpu_init();
+ tcm_init();
/*
* Set up various architecture-specific pointers
#include <asm/tlbflush.h>
#include <asm/ptrace.h>
#include <asm/localtimer.h>
+#include <asm/smp_plat.h>
/*
* as from 2.5, kernels no longer have an init_tasks structure
/*
* __cpu_disable runs on the processor to be shutdown.
*/
-int __cpuexit __cpu_disable(void)
+int __cpu_disable(void)
{
unsigned int cpu = smp_processor_id();
struct task_struct *p;
* called on the thread which is asking for a CPU to be shutdown -
* waits until shutdown has completed, or it is timed out.
*/
-void __cpuexit __cpu_die(unsigned int cpu)
+void __cpu_die(unsigned int cpu)
{
if (!platform_cpu_kill(cpu))
printk("CPU%u: unable to kill\n", cpu);
* of the other hotplug-cpu capable cores, so presumably coming
* out of idle fixes this.
*/
-void __cpuexit cpu_die(void)
+void __ref cpu_die(void)
{
unsigned int cpu = smp_processor_id();
unsigned long ta_end;
};
-/* all SMP configurations have the extended CPUID registers */
-static inline int tlb_ops_need_broadcast(void)
-{
- return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
-}
-
static inline void ipi_flush_tlb_all(void *ignored)
{
local_flush_tlb_all();
clockevents_register_device(clk);
}
+#ifdef CONFIG_HOTPLUG_CPU
/*
* take a local timer down
*/
-void __cpuexit twd_timer_stop(void)
+void twd_timer_stop(void)
{
__raw_writel(0, twd_base + TWD_TIMER_CONTROL);
}
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/stddef.h>
+#include <linux/ioport.h>
+#include <linux/genalloc.h>
+#include <linux/string.h> /* memcpy */
+#include <asm/page.h> /* PAGE_SHIFT */
+#include <asm/cputype.h>
+#include <asm/mach/map.h>
+#include <mach/memory.h>
+#include "tcm.h"
+
+/* Scream and warn about misuse */
+#if !defined(ITCM_OFFSET) || !defined(ITCM_END) || \
+ !defined(DTCM_OFFSET) || !defined(DTCM_END)
+#error "TCM support selected but offsets not defined!"
+#endif
+
+static struct gen_pool *tcm_pool;
+
+/* TCM section definitions from the linker */
+extern char __itcm_start, __sitcm_text, __eitcm_text;
+extern char __dtcm_start, __sdtcm_data, __edtcm_data;
+
+/*
+ * TCM memory resources
+ */
+static struct resource dtcm_res = {
+ .name = "DTCM RAM",
+ .start = DTCM_OFFSET,
+ .end = DTCM_END,
+ .flags = IORESOURCE_MEM
+};
+
+static struct resource itcm_res = {
+ .name = "ITCM RAM",
+ .start = ITCM_OFFSET,
+ .end = ITCM_END,
+ .flags = IORESOURCE_MEM
+};
+
+static struct map_desc dtcm_iomap[] __initdata = {
+ {
+ .virtual = DTCM_OFFSET,
+ .pfn = __phys_to_pfn(DTCM_OFFSET),
+ .length = (DTCM_END - DTCM_OFFSET + 1),
+ .type = MT_UNCACHED
+ }
+};
+
+static struct map_desc itcm_iomap[] __initdata = {
+ {
+ .virtual = ITCM_OFFSET,
+ .pfn = __phys_to_pfn(ITCM_OFFSET),
+ .length = (ITCM_END - ITCM_OFFSET + 1),
+ .type = MT_UNCACHED
+ }
+};
+
+/*
+ * Allocate a chunk of TCM memory
+ */
+void *tcm_alloc(size_t len)
+{
+ unsigned long vaddr;
+
+ if (!tcm_pool)
+ return NULL;
+
+ vaddr = gen_pool_alloc(tcm_pool, len);
+ if (!vaddr)
+ return NULL;
+
+ return (void *) vaddr;
+}
+EXPORT_SYMBOL(tcm_alloc);
+
+/*
+ * Free a chunk of TCM memory
+ */
+void tcm_free(void *addr, size_t len)
+{
+ gen_pool_free(tcm_pool, (unsigned long) addr, len);
+}
+EXPORT_SYMBOL(tcm_free);
+
+
+static void __init setup_tcm_bank(u8 type, u32 offset, u32 expected_size)
+{
+ const int tcm_sizes[16] = { 0, -1, -1, 4, 8, 16, 32, 64, 128,
+ 256, 512, 1024, -1, -1, -1, -1 };
+ u32 tcm_region;
+ int tcm_size;
+
+ /* Read the special TCM region register c9, 0 */
+ if (!type)
+ asm("mrc p15, 0, %0, c9, c1, 0"
+ : "=r" (tcm_region));
+ else
+ asm("mrc p15, 0, %0, c9, c1, 1"
+ : "=r" (tcm_region));
+
+ tcm_size = tcm_sizes[(tcm_region >> 2) & 0x0f];
+ if (tcm_size < 0) {
+ pr_err("CPU: %sTCM of unknown size!\n",
+ type ? "I" : "D");
+ } else {
+ pr_info("CPU: found %sTCM %dk @ %08x, %senabled\n",
+ type ? "I" : "D",
+ tcm_size,
+ (tcm_region & 0xfffff000U),
+ (tcm_region & 1) ? "" : "not ");
+ }
+
+ if (tcm_size != expected_size) {
+ pr_crit("CPU: %sTCM was detected %dk but expected %dk!\n",
+ type ? "I" : "D",
+ tcm_size,
+ expected_size);
+ /* Adjust to the expected size? what can we do... */
+ }
+
+ /* Force move the TCM bank to where we want it, enable */
+ tcm_region = offset | (tcm_region & 0x00000ffeU) | 1;
+
+ if (!type)
+ asm("mcr p15, 0, %0, c9, c1, 0"
+ : /* No output operands */
+ : "r" (tcm_region));
+ else
+ asm("mcr p15, 0, %0, c9, c1, 1"
+ : /* No output operands */
+ : "r" (tcm_region));
+
+ pr_debug("CPU: moved %sTCM %dk to %08x, enabled\n",
+ type ? "I" : "D",
+ tcm_size,
+ (tcm_region & 0xfffff000U));
+}
+
+/*
+ * This initializes the TCM memory
+ */
+void __init tcm_init(void)
+{
+ u32 tcm_status = read_cpuid_tcmstatus();
+ char *start;
+ char *end;
+ char *ram;
+
+ /* Setup DTCM if present */
+ if (tcm_status & (1 << 16)) {
+ setup_tcm_bank(0, DTCM_OFFSET,
+ (DTCM_END - DTCM_OFFSET + 1) >> 10);
+ request_resource(&iomem_resource, &dtcm_res);
+ iotable_init(dtcm_iomap, 1);
+ /* Copy data from RAM to DTCM */
+ start = &__sdtcm_data;
+ end = &__edtcm_data;
+ ram = &__dtcm_start;
+ memcpy(start, ram, (end-start));
+ pr_debug("CPU DTCM: copied data from %p - %p\n", start, end);
+ }
+
+ /* Setup ITCM if present */
+ if (tcm_status & 1) {
+ setup_tcm_bank(1, ITCM_OFFSET,
+ (ITCM_END - ITCM_OFFSET + 1) >> 10);
+ request_resource(&iomem_resource, &itcm_res);
+ iotable_init(itcm_iomap, 1);
+ /* Copy code from RAM to ITCM */
+ start = &__sitcm_text;
+ end = &__eitcm_text;
+ ram = &__itcm_start;
+ memcpy(start, ram, (end-start));
+ pr_debug("CPU ITCM: copied code from %p - %p\n", start, end);
+ }
+}
+
+/*
+ * This creates the TCM memory pool and has to be done later,
+ * during the core_initicalls, since the allocator is not yet
+ * up and running when the first initialization runs.
+ */
+static int __init setup_tcm_pool(void)
+{
+ u32 tcm_status = read_cpuid_tcmstatus();
+ u32 dtcm_pool_start = (u32) &__edtcm_data;
+ u32 itcm_pool_start = (u32) &__eitcm_text;
+ int ret;
+
+ /*
+ * Set up malloc pool, 2^2 = 4 bytes granularity since
+ * the TCM is sometimes just 4 KiB. NB: pages and cache
+ * line alignments does not matter in TCM!
+ */
+ tcm_pool = gen_pool_create(2, -1);
+
+ pr_debug("Setting up TCM memory pool\n");
+
+ /* Add the rest of DTCM to the TCM pool */
+ if (tcm_status & (1 << 16)) {
+ if (dtcm_pool_start < DTCM_END) {
+ ret = gen_pool_add(tcm_pool, dtcm_pool_start,
+ DTCM_END - dtcm_pool_start + 1, -1);
+ if (ret) {
+ pr_err("CPU DTCM: could not add DTCM " \
+ "remainder to pool!\n");
+ return ret;
+ }
+ pr_debug("CPU DTCM: Added %08x bytes @ %08x to " \
+ "the TCM memory pool\n",
+ DTCM_END - dtcm_pool_start + 1,
+ dtcm_pool_start);
+ }
+ }
+
+ /* Add the rest of ITCM to the TCM pool */
+ if (tcm_status & 1) {
+ if (itcm_pool_start < ITCM_END) {
+ ret = gen_pool_add(tcm_pool, itcm_pool_start,
+ ITCM_END - itcm_pool_start + 1, -1);
+ if (ret) {
+ pr_err("CPU ITCM: could not add ITCM " \
+ "remainder to pool!\n");
+ return ret;
+ }
+ pr_debug("CPU ITCM: Added %08x bytes @ %08x to " \
+ "the TCM memory pool\n",
+ ITCM_END - itcm_pool_start + 1,
+ itcm_pool_start);
+ }
+ }
+ return 0;
+}
+
+core_initcall(setup_tcm_pool);
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * TCM memory handling for ARM systems
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Rickard Andersson <rickard.andersson@stericsson.com>
+ */
+
+#ifdef CONFIG_HAVE_TCM
+void __init tcm_init(void);
+#else
+/* No TCM support, just blank inlines to be optimized out */
+inline void tcm_init(void)
+{
+}
+#endif
static inline void
do_cache_op(unsigned long start, unsigned long end, int flags)
{
+ struct mm_struct *mm = current->active_mm;
struct vm_area_struct *vma;
if (end < start || flags)
return;
- vma = find_vma(current->active_mm, start);
+ down_read(&mm->mmap_sem);
+ vma = find_vma(mm, start);
if (vma && vma->vm_start < end) {
if (start < vma->vm_start)
start = vma->vm_start;
flush_cache_user_range(vma, start, end);
}
+ up_read(&mm->mmap_sem);
}
/*
}
_edata_loc = __data_loc + SIZEOF(.data);
+#ifdef CONFIG_HAVE_TCM
+ /*
+ * We align everything to a page boundary so we can
+ * free it after init has commenced and TCM contents have
+ * been copied to its destination.
+ */
+ .tcm_start : {
+ . = ALIGN(PAGE_SIZE);
+ __tcm_start = .;
+ __itcm_start = .;
+ }
+
+ /*
+ * Link these to the ITCM RAM
+ * Put VMA to the TCM address and LMA to the common RAM
+ * and we'll upload the contents from RAM to TCM and free
+ * the used RAM after that.
+ */
+ .text_itcm ITCM_OFFSET : AT(__itcm_start)
+ {
+ __sitcm_text = .;
+ *(.tcm.text)
+ *(.tcm.rodata)
+ . = ALIGN(4);
+ __eitcm_text = .;
+ }
+
+ /*
+ * Reset the dot pointer, this is needed to create the
+ * relative __dtcm_start below (to be used as extern in code).
+ */
+ . = ADDR(.tcm_start) + SIZEOF(.tcm_start) + SIZEOF(.text_itcm);
+
+ .dtcm_start : {
+ __dtcm_start = .;
+ }
+
+ /* TODO: add remainder of ITCM as well, that can be used for data! */
+ .data_dtcm DTCM_OFFSET : AT(__dtcm_start)
+ {
+ . = ALIGN(4);
+ __sdtcm_data = .;
+ *(.tcm.data)
+ . = ALIGN(4);
+ __edtcm_data = .;
+ }
+
+ /* Reset the dot pointer or the linker gets confused */
+ . = ADDR(.dtcm_start) + SIZEOF(.data_dtcm);
+
+ /* End marker for freeing TCM copy in linked object */
+ .tcm_end : AT(ADDR(.dtcm_start) + SIZEOF(.data_dtcm)){
+ . = ALIGN(PAGE_SIZE);
+ __tcm_end = .;
+ }
+#endif
+
.bss : {
__bss_start = .; /* BSS */
*(.bss)
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
+#include <asm/cache.h>
-#define COPY_COUNT (PAGE_SZ/64 PLD( -1 ))
+#define COPY_COUNT (PAGE_SZ / (2 * L1_CACHE_BYTES) PLD( -1 ))
.text
.align 5
ENTRY(copy_page)
stmfd sp!, {r4, lr} @ 2
PLD( pld [r1, #0] )
- PLD( pld [r1, #32] )
+ PLD( pld [r1, #L1_CACHE_BYTES] )
mov r2, #COPY_COUNT @ 1
ldmia r1!, {r3, r4, ip, lr} @ 4+1
-1: PLD( pld [r1, #64] )
- PLD( pld [r1, #96] )
-2: stmia r0!, {r3, r4, ip, lr} @ 4
- ldmia r1!, {r3, r4, ip, lr} @ 4+1
- stmia r0!, {r3, r4, ip, lr} @ 4
- ldmia r1!, {r3, r4, ip, lr} @ 4+1
+1: PLD( pld [r1, #2 * L1_CACHE_BYTES])
+ PLD( pld [r1, #3 * L1_CACHE_BYTES])
+2:
+ .rept (2 * L1_CACHE_BYTES / 16 - 1)
stmia r0!, {r3, r4, ip, lr} @ 4
ldmia r1!, {r3, r4, ip, lr} @ 4
+ .endr
subs r2, r2, #1 @ 1
stmia r0!, {r3, r4, ip, lr} @ 4
ldmgtia r1!, {r3, r4, ip, lr} @ 4
* AC97
* -------------------------------------------------------------------- */
-#if defined(CONFIG_SND_AT91_AC97) || defined(CONFIG_SND_AT91_AC97_MODULE)
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct atmel_ac97_data ac97_data;
+static struct ac97c_platform_data ac97_data;
static struct resource ac97_resources[] = {
[0] = {
};
static struct platform_device at91cap9_ac97_device = {
- .name = "ac97c",
+ .name = "atmel_ac97c",
.id = 1,
.dev = {
.dma_mask = &ac97_dmamask,
.num_resources = ARRAY_SIZE(ac97_resources),
};
-void __init at91_add_device_ac97(struct atmel_ac97_data *data)
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
{
if (!data)
return;
platform_device_register(&at91cap9_ac97_device);
}
#else
-void __init at91_add_device_ac97(struct atmel_ac97_data *data) {}
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#endif
void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
#endif
+/* --------------------------------------------------------------------
+ * CAN Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_CAN_AT91) || defined(CONFIG_CAN_AT91_MODULE)
+static struct resource can_resources[] = {
+ [0] = {
+ .start = AT91SAM9263_BASE_CAN,
+ .end = AT91SAM9263_BASE_CAN + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9263_ID_CAN,
+ .end = AT91SAM9263_ID_CAN,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9263_can_device = {
+ .name = "at91_can",
+ .id = -1,
+ .resource = can_resources,
+ .num_resources = ARRAY_SIZE(can_resources),
+};
+
+void __init at91_add_device_can(struct at91_can_data *data)
+{
+ at91_set_A_periph(AT91_PIN_PA13, 0); /* CANTX */
+ at91_set_A_periph(AT91_PIN_PA14, 0); /* CANRX */
+ at91sam9263_can_device.dev.platform_data = data;
+
+ platform_device_register(&at91sam9263_can_device);
+}
+#else
+void __init at91_add_device_can(struct at91_can_data *data) {}
+#endif
/* --------------------------------------------------------------------
* LCD Controller
#include <mach/at91sam9g45.h>
#include <mach/at91sam9g45_matrix.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
#include "generic.h"
+/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 8,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9G45_ID_DMA,
+ .end = AT91SAM9G45_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
+
/* --------------------------------------------------------------------
* USB Host (OHCI)
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+ [0] = {
+ .start = AT91SAM9G45_BASE_AC97C,
+ .end = AT91SAM9G45_BASE_AC97C + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9G45_ID_AC97C,
+ .end = AT91SAM9G45_ID_AC97C,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9g45_ac97_device = {
+ .name = "atmel_ac97c",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ac97_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &ac97_data,
+ },
+ .resource = ac97_resources,
+ .num_resources = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+ if (!data)
+ return;
+
+ at91_set_A_periph(AT91_PIN_PD8, 0); /* AC97FS */
+ at91_set_A_periph(AT91_PIN_PD9, 0); /* AC97CK */
+ at91_set_A_periph(AT91_PIN_PD7, 0); /* AC97TX */
+ at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */
+
+ /* reset */
+ if (data->reset_pin)
+ at91_set_gpio_output(data->reset_pin, 0);
+
+ ac97_data = *data;
+ platform_device_register(&at91sam9g45_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
*/
static int __init at91_add_standard_devices(void)
{
+ at91_add_device_hdmac();
at91_add_device_rtc();
at91_add_device_rtt();
at91_add_device_watchdog();
#include <mach/at91sam9rl.h>
#include <mach/at91sam9rl_matrix.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at_hdmac.h>
#include "generic.h"
+/* --------------------------------------------------------------------
+ * HDMAC - AHB DMA Controller
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
+static u64 hdmac_dmamask = DMA_BIT_MASK(32);
+
+static struct at_dma_platform_data atdma_pdata = {
+ .nr_channels = 2,
+};
+
+static struct resource hdmac_resources[] = {
+ [0] = {
+ .start = AT91_BASE_SYS + AT91_DMA,
+ .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [2] = {
+ .start = AT91SAM9RL_ID_DMA,
+ .end = AT91SAM9RL_ID_DMA,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at_hdmac_device = {
+ .name = "at_hdmac",
+ .id = -1,
+ .dev = {
+ .dma_mask = &hdmac_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &atdma_pdata,
+ },
+ .resource = hdmac_resources,
+ .num_resources = ARRAY_SIZE(hdmac_resources),
+};
+
+void __init at91_add_device_hdmac(void)
+{
+ dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
+ platform_device_register(&at_hdmac_device);
+}
+#else
+void __init at91_add_device_hdmac(void) {}
+#endif
+
/* --------------------------------------------------------------------
* USB HS Device (Gadget)
* -------------------------------------------------------------------- */
#endif
+/* --------------------------------------------------------------------
+ * AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+ [0] = {
+ .start = AT91SAM9RL_BASE_AC97C,
+ .end = AT91SAM9RL_BASE_AC97C + SZ_16K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AT91SAM9RL_ID_AC97C,
+ .end = AT91SAM9RL_ID_AC97C,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device at91sam9rl_ac97_device = {
+ .name = "atmel_ac97c",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ac97_dmamask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &ac97_data,
+ },
+ .resource = ac97_resources,
+ .num_resources = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+ if (!data)
+ return;
+
+ at91_set_A_periph(AT91_PIN_PD1, 0); /* AC97FS */
+ at91_set_A_periph(AT91_PIN_PD2, 0); /* AC97CK */
+ at91_set_A_periph(AT91_PIN_PD3, 0); /* AC97TX */
+ at91_set_A_periph(AT91_PIN_PD4, 0); /* AC97RX */
+
+ /* reset */
+ if (data->reset_pin)
+ at91_set_gpio_output(data->reset_pin, 0);
+
+ ac97_data = *data;
+ platform_device_register(&at91sam9rl_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
/* --------------------------------------------------------------------
* LCD Controller
* -------------------------------------------------------------------- */
*/
static int __init at91_add_standard_devices(void)
{
+ at91_add_device_hdmac();
at91_add_device_rtc();
at91_add_device_rtt();
at91_add_device_watchdog();
/*
* AC97
*/
-static struct atmel_ac97_data cap9adk_ac97_data = {
+static struct ac97c_platform_data cap9adk_ac97_data = {
// .reset_pin = ... not connected
};
/*
* AC97
*/
-static struct atmel_ac97_data neocore926_ac97_data = {
+static struct ac97c_platform_data neocore926_ac97_data = {
.reset_pin = AT91_PIN_PA13,
};
}
};
+/*
+ * CAN
+ */
+static void sam9263ek_transceiver_switch(int on)
+{
+ if (on) {
+ at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
+ } else {
+ at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
+ at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
+ }
+}
+
+static struct at91_can_data ek_can_data = {
+ .transceiver_switch = sam9263ek_transceiver_switch,
+};
static void __init ek_board_init(void)
{
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
+ /* CAN */
+ at91_add_device_can(&ek_can_data);
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
#endif
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
/*
* LEDs ... these could all be PWM-driven, for variable brightness
*/
at91_add_device_lcdc(&ek_lcdc_data);
/* Push Buttons */
ek_add_device_buttons();
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
/* LEDs */
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
#endif
+/*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
/*
* LEDs
*/
at91_add_device_mmc(0, &ek_mmc_data);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
+ /* AC97 */
+ at91_add_device_ac97(&ek_ac97_data);
/* Touch Screen Controller */
at91_add_device_tsadcc();
/* LEDs */
/* Touchscreen Controller */
extern void __init at91_add_device_tsadcc(void);
+/* CAN */
+struct at91_can_data {
+ void (*transceiver_switch)(int on);
+};
+extern void __init at91_add_device_can(struct at91_can_data *data);
+
/* LEDs */
extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
#include <linux/clocksource.h>
#include <linux/clockchips.h>
-#include <linux/amba/bus.h>
#include <mach/csp/mm_addr.h>
#include <mach/hardware.h>
#include <asm/clkdev.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <cfg_global.h>
#include <mach/common.h>
#include <mach/i2c.h>
#include <mach/serial.h>
-#include <mach/common.h>
#include <mach/mmc.h>
#include <mach/nand.h>
#include <linux/amba/bus.h>
#include <linux/amba/kmi.h>
#include <linux/amba/clcd.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/clkdev.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/irq.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
return status & 8;
}
-static struct mmc_platform_data mmc_data = {
+static struct mmci_platform_data mmc_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
return ret;
}
-struct pci_bus *pci_v3_scan_bus(int nr, struct pci_sys_data *sys)
+struct pci_bus * __init pci_v3_scan_bus(int nr, struct pci_sys_data *sys)
{
return pci_scan_bus(sys->busnr, &pci_v3_ops, sys);
}
return 16;
}
+#define iop_adma_get_max_pq iop_adma_get_max_xor
+
static inline u32 iop_chan_get_current_descriptor(struct iop_adma_chan *chan)
{
return __raw_readl(ADMA_ADAR(chan));
#define IOP_ADMA_MAX_BYTE_COUNT ADMA_MAX_BYTE_COUNT
#define IOP_ADMA_ZERO_SUM_MAX_BYTE_COUNT ADMA_MAX_BYTE_COUNT
#define IOP_ADMA_XOR_MAX_BYTE_COUNT ADMA_MAX_BYTE_COUNT
+#define IOP_ADMA_PQ_MAX_BYTE_COUNT ADMA_MAX_BYTE_COUNT
#define iop_chan_zero_sum_slot_count(l, s, o) iop_chan_xor_slot_count(l, s, o)
+#define iop_chan_pq_slot_count iop_chan_xor_slot_count
+#define iop_chan_pq_zero_sum_slot_count iop_chan_xor_slot_count
static inline u32 iop_desc_get_dest_addr(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan)
return hw_desc->dest_addr;
}
+static inline u32 iop_desc_get_qdest_addr(struct iop_adma_desc_slot *desc,
+ struct iop_adma_chan *chan)
+{
+ struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
+ return hw_desc->q_dest_addr;
+}
+
static inline u32 iop_desc_get_byte_count(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan)
{
return 1;
}
+static inline void
+iop_desc_init_pq(struct iop_adma_desc_slot *desc, int src_cnt,
+ unsigned long flags)
+{
+ struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
+ union {
+ u32 value;
+ struct iop13xx_adma_desc_ctrl field;
+ } u_desc_ctrl;
+
+ u_desc_ctrl.value = 0;
+ u_desc_ctrl.field.src_select = src_cnt - 1;
+ u_desc_ctrl.field.xfer_dir = 3; /* local to internal bus */
+ u_desc_ctrl.field.pq_xfer_en = 1;
+ u_desc_ctrl.field.p_xfer_dis = !!(flags & DMA_PREP_PQ_DISABLE_P);
+ u_desc_ctrl.field.int_en = flags & DMA_PREP_INTERRUPT;
+ hw_desc->desc_ctrl = u_desc_ctrl.value;
+}
+
+static inline int iop_desc_is_pq(struct iop_adma_desc_slot *desc)
+{
+ struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
+ union {
+ u32 value;
+ struct iop13xx_adma_desc_ctrl field;
+ } u_desc_ctrl;
+
+ u_desc_ctrl.value = hw_desc->desc_ctrl;
+ return u_desc_ctrl.field.pq_xfer_en;
+}
+
+static inline void
+iop_desc_init_pq_zero_sum(struct iop_adma_desc_slot *desc, int src_cnt,
+ unsigned long flags)
+{
+ struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
+ union {
+ u32 value;
+ struct iop13xx_adma_desc_ctrl field;
+ } u_desc_ctrl;
+
+ u_desc_ctrl.value = 0;
+ u_desc_ctrl.field.src_select = src_cnt - 1;
+ u_desc_ctrl.field.xfer_dir = 3; /* local to internal bus */
+ u_desc_ctrl.field.zero_result = 1;
+ u_desc_ctrl.field.status_write_back_en = 1;
+ u_desc_ctrl.field.pq_xfer_en = 1;
+ u_desc_ctrl.field.p_xfer_dis = !!(flags & DMA_PREP_PQ_DISABLE_P);
+ u_desc_ctrl.field.int_en = flags & DMA_PREP_INTERRUPT;
+ hw_desc->desc_ctrl = u_desc_ctrl.value;
+}
+
static inline void iop_desc_set_byte_count(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan,
u32 byte_count)
}
}
+#define iop_desc_set_pq_zero_sum_byte_count iop_desc_set_zero_sum_byte_count
static inline void iop_desc_set_dest_addr(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan,
hw_desc->upper_dest_addr = 0;
}
+static inline void
+iop_desc_set_pq_addr(struct iop_adma_desc_slot *desc, dma_addr_t *addr)
+{
+ struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
+
+ hw_desc->dest_addr = addr[0];
+ hw_desc->q_dest_addr = addr[1];
+ hw_desc->upper_dest_addr = 0;
+}
+
static inline void iop_desc_set_memcpy_src_addr(struct iop_adma_desc_slot *desc,
dma_addr_t addr)
{
} while (slot_cnt);
}
+static inline void
+iop_desc_set_pq_src_addr(struct iop_adma_desc_slot *desc, int src_idx,
+ dma_addr_t addr, unsigned char coef)
+{
+ int slot_cnt = desc->slot_cnt, slots_per_op = desc->slots_per_op;
+ struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc, *iter;
+ struct iop13xx_adma_src *src;
+ int i = 0;
+
+ do {
+ iter = iop_hw_desc_slot_idx(hw_desc, i);
+ src = &iter->src[src_idx];
+ src->src_addr = addr;
+ src->pq_upper_src_addr = 0;
+ src->pq_dmlt = coef;
+ slot_cnt -= slots_per_op;
+ if (slot_cnt) {
+ i += slots_per_op;
+ addr += IOP_ADMA_PQ_MAX_BYTE_COUNT;
+ }
+ } while (slot_cnt);
+}
+
static inline void
iop_desc_init_interrupt(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *chan)
}
#define iop_desc_set_zero_sum_src_addr iop_desc_set_xor_src_addr
+#define iop_desc_set_pq_zero_sum_src_addr iop_desc_set_pq_src_addr
+
+static inline void
+iop_desc_set_pq_zero_sum_addr(struct iop_adma_desc_slot *desc, int pq_idx,
+ dma_addr_t *src)
+{
+ iop_desc_set_xor_src_addr(desc, pq_idx, src[pq_idx]);
+ iop_desc_set_xor_src_addr(desc, pq_idx+1, src[pq_idx+1]);
+}
static inline void iop_desc_set_next_desc(struct iop_adma_desc_slot *desc,
u32 next_desc_addr)
hw_desc->block_fill_data = val;
}
-static inline int iop_desc_get_zero_result(struct iop_adma_desc_slot *desc)
+static inline enum sum_check_flags
+iop_desc_get_zero_result(struct iop_adma_desc_slot *desc)
{
struct iop13xx_adma_desc_hw *hw_desc = desc->hw_desc;
struct iop13xx_adma_desc_ctrl desc_ctrl = hw_desc->desc_ctrl_field;
struct iop13xx_adma_byte_count byte_count = hw_desc->byte_count_field;
+ enum sum_check_flags flags;
BUG_ON(!(byte_count.tx_complete && desc_ctrl.zero_result));
- if (desc_ctrl.pq_xfer_en)
- return byte_count.zero_result_err_q;
- else
- return byte_count.zero_result_err;
+ flags = byte_count.zero_result_err_q << SUM_CHECK_Q;
+ flags |= byte_count.zero_result_err << SUM_CHECK_P;
+
+ return flags;
}
static inline void iop_chan_append(struct iop_adma_chan *chan)
plat_data = &iop13xx_adma_0_data;
dma_cap_set(DMA_MEMCPY, plat_data->cap_mask);
dma_cap_set(DMA_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_DUAL_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_ZERO_SUM, plat_data->cap_mask);
+ dma_cap_set(DMA_XOR_VAL, plat_data->cap_mask);
dma_cap_set(DMA_MEMSET, plat_data->cap_mask);
- dma_cap_set(DMA_MEMCPY_CRC32C, plat_data->cap_mask);
dma_cap_set(DMA_INTERRUPT, plat_data->cap_mask);
break;
case IOP13XX_INIT_ADMA_1:
plat_data = &iop13xx_adma_1_data;
dma_cap_set(DMA_MEMCPY, plat_data->cap_mask);
dma_cap_set(DMA_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_DUAL_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_ZERO_SUM, plat_data->cap_mask);
+ dma_cap_set(DMA_XOR_VAL, plat_data->cap_mask);
dma_cap_set(DMA_MEMSET, plat_data->cap_mask);
- dma_cap_set(DMA_MEMCPY_CRC32C, plat_data->cap_mask);
dma_cap_set(DMA_INTERRUPT, plat_data->cap_mask);
break;
case IOP13XX_INIT_ADMA_2:
plat_data = &iop13xx_adma_2_data;
dma_cap_set(DMA_MEMCPY, plat_data->cap_mask);
dma_cap_set(DMA_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_DUAL_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_ZERO_SUM, plat_data->cap_mask);
+ dma_cap_set(DMA_XOR_VAL, plat_data->cap_mask);
dma_cap_set(DMA_MEMSET, plat_data->cap_mask);
- dma_cap_set(DMA_MEMCPY_CRC32C, plat_data->cap_mask);
dma_cap_set(DMA_INTERRUPT, plat_data->cap_mask);
- dma_cap_set(DMA_PQ_XOR, plat_data->cap_mask);
- dma_cap_set(DMA_PQ_UPDATE, plat_data->cap_mask);
- dma_cap_set(DMA_PQ_ZERO_SUM, plat_data->cap_mask);
+ dma_cap_set(DMA_PQ, plat_data->cap_mask);
+ dma_cap_set(DMA_PQ_VAL, plat_data->cap_mask);
break;
}
}
#define IOP32X_MAX_RAM_SIZE 0x40000000UL
#define IOP3XX_MAX_RAM_SIZE IOP32X_MAX_RAM_SIZE
#define IOP3XX_PCI_LOWER_MEM_BA 0x80000000
-#define IOP32X_PCI_MEM_WINDOW_SIZE 0x04000000
-#define IOP3XX_PCI_MEM_WINDOW_SIZE IOP32X_PCI_MEM_WINDOW_SIZE
#endif
#define IOP33X_MAX_RAM_SIZE 0x80000000UL
#define IOP3XX_MAX_RAM_SIZE IOP33X_MAX_RAM_SIZE
#define IOP3XX_PCI_LOWER_MEM_BA (PHYS_OFFSET + IOP33X_MAX_RAM_SIZE)
-#define IOP33X_PCI_MEM_WINDOW_SIZE 0x08000000
-#define IOP3XX_PCI_MEM_WINDOW_SIZE IOP33X_PCI_MEM_WINDOW_SIZE
#endif
return single_open(file, clk_debugfs_show, NULL);
}
-static struct file_operations clk_debugfs_operations = {
+static const struct file_operations clk_debugfs_operations = {
.open = clk_debugfs_open,
.read = seq_read,
.llseek = seq_lseek,
{ .jtag_id = 0xb574, .die_rev = 0x2, .omap_id = 0x03310315, .type = 0x03100000},
{ .jtag_id = 0x355f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300100},
{ .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x07300300},
- { .jtag_id = 0xb55f, .die_rev = 0x0, .omap_id = 0x03320500, .type = 0x08500000},
+ { .jtag_id = 0xb62c, .die_rev = 0x1, .omap_id = 0x03320500, .type = 0x08500000},
{ .jtag_id = 0xb470, .die_rev = 0x0, .omap_id = 0x03310100, .type = 0x15100000},
{ .jtag_id = 0xb576, .die_rev = 0x0, .omap_id = 0x03320000, .type = 0x16100000},
{ .jtag_id = 0xb576, .die_rev = 0x2, .omap_id = 0x03320100, .type = 0x16110000},
#define TWL4030_MSECURE_GPIO 22
-static int sdp3430_keymap[] = {
+static int board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
KEY(0, 2, KEY_A),
0
};
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
static struct twl4030_keypad_data sdp3430_kp_data = {
+ .keymap_data = &board_map_data,
.rows = 5,
.cols = 6,
- .keymap = sdp3430_keymap,
- .keymapsize = ARRAY_SIZE(sdp3430_keymap),
.rep = 1,
};
},
};
-static int ldp_twl4030_keymap[] = {
+static int board_keymap[] = {
KEY(0, 0, KEY_1),
KEY(1, 0, KEY_2),
KEY(2, 0, KEY_3),
0
};
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
static struct twl4030_keypad_data ldp_kp_twl4030_data = {
+ .keymap_data = &board_map_data,
.rows = 6,
.cols = 6,
- .keymap = ldp_twl4030_keymap,
- .keymapsize = ARRAY_SIZE(ldp_twl4030_keymap),
.rep = 1,
};
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
+ if (system_rev >= 0x20 && system_rev <= 0x34301000) {
+ omap_cfg_reg(AG9_34XX_GPIO23);
+ mmc[0].gpio_wp = 23;
+ } else {
+ omap_cfg_reg(AH8_34XX_GPIO29);
+ }
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
- omap_cfg_reg(AH8_34XX_GPIO29);
mmc[0].gpio_cd = gpio + 0;
twl4030_mmc_init(mmc);
.usb_mode = T2_USB_MODE_ULPI,
};
-static int omap3evm_keymap[] = {
+static int board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
KEY(0, 2, KEY_A),
KEY(3, 3, KEY_P)
};
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
static struct twl4030_keypad_data omap3evm_kp_data = {
+ .keymap_data = &board_map_data,
.rows = 4,
.cols = 4,
- .keymap = omap3evm_keymap,
- .keymapsize = ARRAY_SIZE(omap3evm_keymap),
.rep = 1,
};
omap_set_gpio_debounce_time(32 * 5, GPIO_DEBOUNCE_TIME);
}
-static int pandora_keypad_map[] = {
+static int board_keymap[] = {
/* col, row, code */
KEY(0, 0, KEY_9),
KEY(0, 1, KEY_0),
KEY(5, 2, KEY_FN),
};
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
static struct twl4030_keypad_data pandora_kp_data = {
+ .keymap_data = &board_map_data,
.rows = 8,
.cols = 6,
- .keymap = pandora_keypad_map,
- .keymapsize = ARRAY_SIZE(pandora_keypad_map),
.rep = 1,
};
#define SYSTEM_REV_B_USES_VAUX3 0x1699
#define SYSTEM_REV_S_USES_VAUX3 0x8
-static int rx51_keymap[] = {
+static int board_keymap[] = {
KEY(0, 0, KEY_Q),
KEY(0, 1, KEY_W),
KEY(0, 2, KEY_E),
KEY(0xff, 5, KEY_F10),
};
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
static struct twl4030_keypad_data rx51_kp_data = {
+ .keymap_data = &board_map_data,
.rows = 8,
.cols = 8,
- .keymap = rx51_keymap,
- .keymapsize = ARRAY_SIZE(rx51_keymap),
.rep = 1,
};
#include "mmc-twl4030.h"
/* Zoom2 has Qwerty keyboard*/
-static int zoom2_twl4030_keymap[] = {
+static int board_keymap[] = {
KEY(0, 0, KEY_E),
KEY(1, 0, KEY_R),
KEY(2, 0, KEY_T),
0
};
+static struct matrix_keymap_data board_map_data = {
+ .keymap = board_keymap,
+ .keymap_size = ARRAY_SIZE(board_keymap),
+};
+
static struct twl4030_keypad_data zoom2_kp_twl4030_data = {
+ .keymap_data = &board_map_data,
.rows = 8,
.cols = 8,
- .keymap = zoom2_twl4030_keymap,
- .keymapsize = ARRAY_SIZE(zoom2_twl4030_keymap),
.rep = 1,
};
#include <asm/atomic.h>
#include "cm.h"
-#include "cm-regbits-4xxx.h"
/* XXX move this to cm.h */
/* MAX_MODULE_READY_TIME: max milliseconds for module to leave idle */
*/
int omap4_cm_wait_idlest_ready(u32 prcm_mod, u8 prcm_dev_offs)
{
- int i = 0;
- u8 cm_id;
- u16 prcm_mod_offs;
- u32 mask = OMAP4_PRCM_CM_CLKCTRL_IDLEST_MASK;
-
- cm_id = prcm_mod >> OMAP4_PRCM_MOD_CM_ID_SHIFT;
- prcm_mod_offs = prcm_mod & OMAP4_PRCM_MOD_OFFS_MASK;
-
- while (((omap4_cm_read_mod_reg(cm_id, prcm_mod_offs, prcm_dev_offs,
- OMAP4_CM_CLKCTRL_DREG) & mask) != 0) &&
- (i++ < MAX_MODULE_READY_TIME))
- udelay(1);
-
- return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+ /* FIXME: Add clock manager related code */
+ return 0;
}
};
#endif
-static void omap_init_mcspi(void)
+#ifdef CONFIG_ARCH_OMAP4
+static inline void omap4_mcspi_fixup(void)
{
- if (cpu_is_omap44xx()) {
- omap2_mcspi1_resources[0].start = OMAP4_MCSPI1_BASE;
- omap2_mcspi1_resources[0].end = OMAP4_MCSPI1_BASE + 0xff;
- omap2_mcspi2_resources[0].start = OMAP4_MCSPI2_BASE;
- omap2_mcspi2_resources[0].end = OMAP4_MCSPI2_BASE + 0xff;
- omap2_mcspi3_resources[0].start = OMAP4_MCSPI3_BASE;
- omap2_mcspi3_resources[0].end = OMAP4_MCSPI3_BASE + 0xff;
- omap2_mcspi4_resources[0].start = OMAP4_MCSPI4_BASE;
- omap2_mcspi4_resources[0].end = OMAP4_MCSPI4_BASE + 0xff;
- }
- platform_device_register(&omap2_mcspi1);
- platform_device_register(&omap2_mcspi2);
+ omap2_mcspi1_resources[0].start = OMAP4_MCSPI1_BASE;
+ omap2_mcspi1_resources[0].end = OMAP4_MCSPI1_BASE + 0xff;
+ omap2_mcspi2_resources[0].start = OMAP4_MCSPI2_BASE;
+ omap2_mcspi2_resources[0].end = OMAP4_MCSPI2_BASE + 0xff;
+ omap2_mcspi3_resources[0].start = OMAP4_MCSPI3_BASE;
+ omap2_mcspi3_resources[0].end = OMAP4_MCSPI3_BASE + 0xff;
+ omap2_mcspi4_resources[0].start = OMAP4_MCSPI4_BASE;
+ omap2_mcspi4_resources[0].end = OMAP4_MCSPI4_BASE + 0xff;
+}
+#else
+static inline void omap4_mcspi_fixup(void)
+{
+}
+#endif
+
#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP3) || \
defined(CONFIG_ARCH_OMAP4)
- if (cpu_is_omap2430() || cpu_is_omap343x() || cpu_is_omap44xx())
- platform_device_register(&omap2_mcspi3);
+static inline void omap2_mcspi3_init(void)
+{
+ platform_device_register(&omap2_mcspi3);
+}
+#else
+static inline void omap2_mcspi3_init(void)
+{
+}
#endif
+
#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
- if (cpu_is_omap343x() || cpu_is_omap44xx())
- platform_device_register(&omap2_mcspi4);
+static inline void omap2_mcspi4_init(void)
+{
+ platform_device_register(&omap2_mcspi4);
+}
+#else
+static inline void omap2_mcspi4_init(void)
+{
+}
#endif
+
+static void omap_init_mcspi(void)
+{
+ if (cpu_is_omap44xx())
+ omap4_mcspi_fixup();
+
+ platform_device_register(&omap2_mcspi1);
+ platform_device_register(&omap2_mcspi2);
+
+ if (cpu_is_omap2430() || cpu_is_omap343x() || cpu_is_omap44xx())
+ omap2_mcspi3_init();
+
+ if (cpu_is_omap343x() || cpu_is_omap44xx())
+ omap2_mcspi4_init();
}
#else
else if (cpu_is_omap34xx())
hwmods = omap34xx_hwmods;
- omap_hwmod_init(hwmods);
- omap2_mux_init();
#ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
/* The OPP tables have to be registered before a clk init */
+ omap_hwmod_init(hwmods);
+ omap2_mux_init();
omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
pwrdm_init(powerdomains_omap);
clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
l = iommu_read_reg(obj, MMU_SYSSTATUS);
if (l & MMU_SYS_RESETDONE)
break;
- } while (time_after(jiffies, timeout));
+ } while (!time_after(jiffies, timeout));
if (!(l & MMU_SYS_RESETDONE)) {
dev_err(obj->dev, "can't take mmu out of reset\n");
#define MAILBOX_IRQ_NEWMSG(u) (1 << (2 * (u)))
#define MAILBOX_IRQ_NOTFULL(u) (1 << (2 * (u) + 1))
+/* SYSCONFIG: register bit definition */
+#define AUTOIDLE (1 << 0)
+#define SOFTRESET (1 << 1)
+#define SMARTIDLE (2 << 3)
+
+/* SYSSTATUS: register bit definition */
+#define RESETDONE (1 << 0)
+
#define MBOX_REG_SIZE 0x120
#define MBOX_NR_REGS (MBOX_REG_SIZE / sizeof(u32))
/* Mailbox H/W preparations */
static int omap2_mbox_startup(struct omap_mbox *mbox)
{
- unsigned int l;
+ u32 l;
+ unsigned long timeout;
mbox_ick_handle = clk_get(NULL, "mailboxes_ick");
if (IS_ERR(mbox_ick_handle)) {
- printk("Could not get mailboxes_ick\n");
+ pr_err("Can't get mailboxes_ick\n");
return -ENODEV;
}
clk_enable(mbox_ick_handle);
+ mbox_write_reg(SOFTRESET, MAILBOX_SYSCONFIG);
+ timeout = jiffies + msecs_to_jiffies(20);
+ do {
+ l = mbox_read_reg(MAILBOX_SYSSTATUS);
+ if (l & RESETDONE)
+ break;
+ } while (!time_after(jiffies, timeout));
+
+ if (!(l & RESETDONE)) {
+ pr_err("Can't take mmu out of reset\n");
+ return -ENODEV;
+ }
+
l = mbox_read_reg(MAILBOX_REVISION);
pr_info("omap mailbox rev %d.%d\n", (l & 0xf0) >> 4, (l & 0x0f));
- /* set smart-idle & autoidle */
- l = mbox_read_reg(MAILBOX_SYSCONFIG);
- l |= 0x00000011;
+ l = SMARTIDLE | AUTOIDLE;
mbox_write_reg(l, MAILBOX_SYSCONFIG);
omap2_mbox_enable_irq(mbox, IRQ_RX);
u32 bit = (irq == IRQ_TX) ? p->notfull_bit : p->newmsg_bit;
mbox_write_reg(bit, p->irqstatus);
+
+ /* Flush posted write for irq status to avoid spurious interrupts */
+ mbox_read_reg(p->irqstatus);
}
static int omap2_mbox_is_irq(struct omap_mbox *mbox,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
MUX_CFG_34XX("AF22_34XX_GPIO9", 0xa18,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+MUX_CFG_34XX("AG9_34XX_GPIO23", 0x5ee,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
MUX_CFG_34XX("AH8_34XX_GPIO29", 0x5fa,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
MUX_CFG_34XX("U8_34XX_GPIO54_OUT", 0x0b4,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
MUX_CFG_34XX("AG4_34XX_GPIO134_OUT", 0x160,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("AF4_34XX_GPIO135_OUT", 0x162,
+ OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
MUX_CFG_34XX("AE4_34XX_GPIO136_OUT", 0x164,
OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
MUX_CFG_34XX("AF6_34XX_GPIO140_UP", 0x16c,
.uartclk = OMAP24XX_BASE_BAUD * 16,
}, {
#ifdef CONFIG_ARCH_OMAP4
- .membase = IO_ADDRESS(OMAP_UART4_BASE),
+ .membase = OMAP2_IO_ADDRESS(OMAP_UART4_BASE),
.mapbase = OMAP_UART4_BASE,
.irq = 70,
.flags = UPF_BOOT_AUTOCONF,
#ifdef CONFIG_ARCH_OMAP4
static struct plat_serial8250_port serial_platform_data3[] = {
{
- .membase = IO_ADDRESS(OMAP_UART4_BASE),
+ .membase = OMAP2_IO_ADDRESS(OMAP_UART4_BASE),
.mapbase = OMAP_UART4_BASE,
.irq = 70,
.flags = UPF_BOOT_AUTOCONF,
{
.pdev = {
.name = "serial8250",
- .id = 3
+ .id = 3,
.dev = {
.platform_data = serial_platform_data3,
},
config CPU_PXA935
bool "PXA935 (codename Tavor-P65)"
+ select CPU_PXA930
+
+config CPU_PXA950
+ bool "PXA950 (codename Tavor-PV2)"
+ select CPU_PXA930
endmenu
bool "Nec Mobilepro 900/c"
select PXA25x
+config MACH_BALLOON3
+ bool "Balloon 3 board"
+ select PXA27x
+ select IWMMXT
+ select PXA_HAVE_BOARD_IRQS
+
config ARCH_PXA_IDP
bool "Accelent Xscale IDP"
select PXA25x
Say Y here if you intend to run this kernel on a Palm Tungsten|E2
handheld computer.
+config MACH_PALMTC
+ bool "Palm Tungsten|C"
+ default y
+ depends on ARCH_PXA_PALM
+ select PXA25x
+ help
+ Say Y here if you intend to run this kernel on a Palm Tungsten|C
+ handheld computer.
+
config MACH_PALMT5
bool "Palm Tungsten|T5"
default y
select PXA27x
select IWMMXT
select HAVE_PWM
+ select PXA_HAVE_BOARD_IRQS
config MACH_EZX_A780
bool "Motorola EZX A780"
default y
depends on PXA_EZX
+config MACH_XCEP
+ bool "Iskratel Electronics XCEP"
+ select PXA25x
+ select MTD
+ select MTD_PARTITIONS
+ select MTD_PHYSMAP
+ select MTD_CFI_INTELEXT
+ select MTD_CFI
+ select MTD_CHAR
+ select SMC91X
+ select PXA_SSP
+ help
+ PXA255 based Single Board Computer with SMC 91C111 ethernet chip and 64 MB of flash.
+ Tuned for usage in Libera instruments for particle accelerators.
+
endmenu
config PXA25x
obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o
obj-$(CONFIG_MACH_LOGICPD_PXA270) += lpd270.o
obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o
+obj-$(CONFIG_MACH_BALLOON3) += balloon3.o
obj-$(CONFIG_MACH_MP900C) += mp900.o
obj-$(CONFIG_ARCH_PXA_IDP) += idp.o
obj-$(CONFIG_MACH_TRIZEPS4) += trizeps4.o
obj-$(CONFIG_MACH_E400) += e400.o
obj-$(CONFIG_MACH_E800) += e800.o
obj-$(CONFIG_MACH_PALMTE2) += palmte2.o
+obj-$(CONFIG_MACH_PALMTC) += palmtc.o
obj-$(CONFIG_MACH_PALMT5) += palmt5.o
obj-$(CONFIG_MACH_PALMTX) += palmtx.o
obj-$(CONFIG_MACH_PALMLD) += palmld.o
obj-$(CONFIG_MACH_CM_X300) += cm-x300.o
obj-$(CONFIG_PXA_EZX) += ezx.o
+obj-$(CONFIG_MACH_XCEP) += xcep.o
+
obj-$(CONFIG_MACH_INTELMOTE2) += imote2.o
obj-$(CONFIG_MACH_STARGATE2) += stargate2.o
obj-$(CONFIG_MACH_CSB726) += csb726.o
--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/balloon3.c
+ *
+ * Support for Balloonboard.org Balloon3 board.
+ *
+ * Author: Nick Bane, Wookey, Jonathan McDowell
+ * Created: June, 2006
+ * Copyright: Toby Churchill Ltd
+ * Derived from mainstone.c, by Nico Pitre
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/bitops.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/ioport.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/types.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+#include <asm/sizes.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/flash.h>
+
+#include <mach/pxa27x.h>
+#include <mach/balloon3.h>
+#include <mach/audio.h>
+#include <mach/pxafb.h>
+#include <mach/mmc.h>
+#include <mach/udc.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/irda.h>
+#include <mach/ohci.h>
+
+#include <plat/i2c.h>
+
+#include "generic.h"
+#include "devices.h"
+
+static unsigned long balloon3_irq_enabled;
+
+static unsigned long balloon3_features_present =
+ (1 << BALLOON3_FEATURE_OHCI) | (1 << BALLOON3_FEATURE_CF) |
+ (1 << BALLOON3_FEATURE_AUDIO) |
+ (1 << BALLOON3_FEATURE_TOPPOLY);
+
+int balloon3_has(enum balloon3_features feature)
+{
+ return (balloon3_features_present & (1 << feature)) ? 1 : 0;
+}
+EXPORT_SYMBOL_GPL(balloon3_has);
+
+int __init parse_balloon3_features(char *arg)
+{
+ if (!arg)
+ return 0;
+
+ return strict_strtoul(arg, 0, &balloon3_features_present);
+}
+early_param("balloon3_features", parse_balloon3_features);
+
+static void balloon3_mask_irq(unsigned int irq)
+{
+ int balloon3_irq = (irq - BALLOON3_IRQ(0));
+ balloon3_irq_enabled &= ~(1 << balloon3_irq);
+ __raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static void balloon3_unmask_irq(unsigned int irq)
+{
+ int balloon3_irq = (irq - BALLOON3_IRQ(0));
+ balloon3_irq_enabled |= (1 << balloon3_irq);
+ __raw_writel(~balloon3_irq_enabled, BALLOON3_INT_CONTROL_REG);
+}
+
+static struct irq_chip balloon3_irq_chip = {
+ .name = "FPGA",
+ .ack = balloon3_mask_irq,
+ .mask = balloon3_mask_irq,
+ .unmask = balloon3_unmask_irq,
+};
+
+static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+ unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+ balloon3_irq_enabled;
+
+ do {
+ /* clear useless edge notification */
+ if (desc->chip->ack)
+ desc->chip->ack(BALLOON3_AUX_NIRQ);
+ while (pending) {
+ irq = BALLOON3_IRQ(0) + __ffs(pending);
+ generic_handle_irq(irq);
+ pending &= pending - 1;
+ }
+ pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
+ balloon3_irq_enabled;
+ } while (pending);
+}
+
+static void __init balloon3_init_irq(void)
+{
+ int irq;
+
+ pxa27x_init_irq();
+ /* setup extra Balloon3 irqs */
+ for (irq = BALLOON3_IRQ(0); irq <= BALLOON3_IRQ(7); irq++) {
+ set_irq_chip(irq, &balloon3_irq_chip);
+ set_irq_handler(irq, handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+ }
+
+ set_irq_chained_handler(BALLOON3_AUX_NIRQ, balloon3_irq_handler);
+ set_irq_type(BALLOON3_AUX_NIRQ, IRQ_TYPE_EDGE_FALLING);
+
+ pr_debug("%s: chained handler installed - irq %d automatically "
+ "enabled\n", __func__, BALLOON3_AUX_NIRQ);
+}
+
+static void balloon3_backlight_power(int on)
+{
+ pr_debug("%s: power is %s\n", __func__, on ? "on" : "off");
+ gpio_set_value(BALLOON3_GPIO_RUN_BACKLIGHT, on);
+}
+
+static unsigned long balloon3_lcd_pin_config[] = {
+ /* LCD - 16bpp Active TFT */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+ GPIO77_LCD_BIAS,
+
+ GPIO99_GPIO, /* Backlight */
+};
+
+static struct pxafb_mode_info balloon3_lcd_modes[] = {
+ {
+ .pixclock = 38000,
+ .xres = 480,
+ .yres = 640,
+ .bpp = 16,
+ .hsync_len = 8,
+ .left_margin = 8,
+ .right_margin = 8,
+ .vsync_len = 2,
+ .upper_margin = 4,
+ .lower_margin = 5,
+ .sync = 0,
+ },
+};
+
+static struct pxafb_mach_info balloon3_pxafb_info = {
+ .modes = balloon3_lcd_modes,
+ .num_modes = ARRAY_SIZE(balloon3_lcd_modes),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+ .pxafb_backlight_power = balloon3_backlight_power,
+};
+
+static unsigned long balloon3_mmc_pin_config[] = {
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+};
+
+static void balloon3_mci_setpower(struct device *dev, unsigned int vdd)
+{
+ struct pxamci_platform_data *p_d = dev->platform_data;
+
+ if ((1 << vdd) & p_d->ocr_mask) {
+ pr_debug("%s: on\n", __func__);
+ /* FIXME something to prod here? */
+ } else {
+ pr_debug("%s: off\n", __func__);
+ /* FIXME something to prod here? */
+ }
+}
+
+static struct pxamci_platform_data balloon3_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .setpower = balloon3_mci_setpower,
+};
+
+static int balloon3_udc_is_connected(void)
+{
+ pr_debug("%s: udc connected\n", __func__);
+ return 1;
+}
+
+static void balloon3_udc_command(int cmd)
+{
+ switch (cmd) {
+ case PXA2XX_UDC_CMD_CONNECT:
+ UP2OCR |= (UP2OCR_DPPUE + UP2OCR_DPPUBE);
+ pr_debug("%s: connect\n", __func__);
+ break;
+ case PXA2XX_UDC_CMD_DISCONNECT:
+ UP2OCR &= ~UP2OCR_DPPUE;
+ pr_debug("%s: disconnect\n", __func__);
+ break;
+ }
+}
+
+static struct pxa2xx_udc_mach_info balloon3_udc_info = {
+ .udc_is_connected = balloon3_udc_is_connected,
+ .udc_command = balloon3_udc_command,
+};
+
+static struct pxaficp_platform_data balloon3_ficp_platform_data = {
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
+};
+
+static unsigned long balloon3_ohci_pin_config[] = {
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+};
+
+static struct pxaohci_platform_data balloon3_ohci_platform_data = {
+ .port_mode = PMM_PERPORT_MODE,
+ .flags = ENABLE_PORT_ALL | POWER_CONTROL_LOW | POWER_SENSE_LOW,
+};
+
+static unsigned long balloon3_pin_config[] __initdata = {
+ /* Select BTUART 'COM1/ttyS0' as IO option for pins 42/43/44/45 */
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO44_BTUART_CTS,
+ GPIO45_BTUART_RTS,
+
+ /* Wakeup GPIO */
+ GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
+
+ /* NAND & IDLE LED GPIOs */
+ GPIO9_GPIO,
+ GPIO10_GPIO,
+};
+
+static struct gpio_led balloon3_gpio_leds[] = {
+ {
+ .name = "balloon3:green:idle",
+ .default_trigger = "heartbeat",
+ .gpio = BALLOON3_GPIO_LED_IDLE,
+ .active_low = 1,
+ },
+ {
+ .name = "balloon3:green:nand",
+ .default_trigger = "nand-disk",
+ .gpio = BALLOON3_GPIO_LED_NAND,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led_platform_data balloon3_gpio_leds_platform_data = {
+ .leds = balloon3_gpio_leds,
+ .num_leds = ARRAY_SIZE(balloon3_gpio_leds),
+};
+
+static struct platform_device balloon3led_device = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &balloon3_gpio_leds_platform_data,
+ },
+};
+
+static void __init balloon3_init(void)
+{
+ pr_info("Initialising Balloon3\n");
+
+ /* system bus arbiter setting
+ * - Core_Park
+ * - LCD_wt:DMA_wt:CORE_Wt = 2:3:4
+ */
+ ARB_CNTRL = ARB_CORE_PARK | 0x234;
+
+ pxa_set_i2c_info(NULL);
+ if (balloon3_has(BALLOON3_FEATURE_AUDIO))
+ pxa_set_ac97_info(NULL);
+
+ if (balloon3_has(BALLOON3_FEATURE_TOPPOLY)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_lcd_pin_config));
+ gpio_request(BALLOON3_GPIO_RUN_BACKLIGHT,
+ "LCD Backlight Power");
+ gpio_direction_output(BALLOON3_GPIO_RUN_BACKLIGHT, 1);
+ set_pxa_fb_info(&balloon3_pxafb_info);
+ }
+
+ if (balloon3_has(BALLOON3_FEATURE_MMC)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_mmc_pin_config));
+ pxa_set_mci_info(&balloon3_mci_platform_data);
+ }
+ pxa_set_ficp_info(&balloon3_ficp_platform_data);
+ if (balloon3_has(BALLOON3_FEATURE_OHCI)) {
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_ohci_pin_config));
+ pxa_set_ohci_info(&balloon3_ohci_platform_data);
+ }
+ pxa_set_udc_info(&balloon3_udc_info);
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(balloon3_pin_config));
+
+ platform_device_register(&balloon3led_device);
+}
+
+static struct map_desc balloon3_io_desc[] __initdata = {
+ { /* CPLD/FPGA */
+ .virtual = BALLOON3_FPGA_VIRT,
+ .pfn = __phys_to_pfn(BALLOON3_FPGA_PHYS),
+ .length = BALLOON3_FPGA_LENGTH,
+ .type = MT_DEVICE,
+ },
+};
+
+static void __init balloon3_map_io(void)
+{
+ pxa_map_io();
+ iotable_init(balloon3_io_desc, ARRAY_SIZE(balloon3_io_desc));
+}
+
+MACHINE_START(BALLOON3, "Balloon3")
+ /* Maintainer: Nick Bane. */
+ .phys_io = 0x40000000,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = balloon3_map_io,
+ .init_irq = balloon3_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = balloon3_init,
+ .boot_params = PHYS_OFFSET + 0x100,
+MACHINE_END
unsigned int cken;
unsigned int delay;
unsigned int enabled;
- struct clk *other;
};
#define INIT_CLKREG(_clk,_devname,_conname) \
#include <linux/sysdev.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/delay.h>
#include <linux/rtc-v3020.h>
#include <video/mbxfb.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/libertas_spi.h>
+
#include <mach/pxa27x.h>
#include <mach/ohci.h>
#include <mach/mmc.h>
+#include <mach/pxa2xx_spi.h>
#include "generic.h"
/* MMC power enable */
#define GPIO105_MMC_POWER (105)
+/* WLAN GPIOS */
+#define GPIO19_WLAN_STRAP (19)
+#define GPIO102_WLAN_RST (102)
+
static unsigned long cmx270_pin_config[] = {
/* AC'97 */
GPIO28_AC97_BITCLK,
GPIO26_SSP1_RXD,
/* SSP2 */
- GPIO19_SSP2_SCLK,
- GPIO14_SSP2_SFRM,
+ GPIO19_GPIO, /* SSP2 clock is used as GPIO for Libertas pin-strap */
+ GPIO14_GPIO,
GPIO87_SSP2_TXD,
GPIO88_SSP2_RXD,
GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,
GPIO105_GPIO | MFP_LPM_DRIVE_HIGH, /* MMC/SD power */
GPIO53_GPIO, /* PC card reset */
+ GPIO102_GPIO, /* WLAN reset */
/* NAND controls */
GPIO11_GPIO | MFP_LPM_DRIVE_HIGH, /* NAND CE# */
/* interrupts */
GPIO10_GPIO, /* DM9000 interrupt */
GPIO83_GPIO, /* MMC card detect */
+ GPIO95_GPIO, /* WLAN interrupt */
};
/* V3020 RTC */
#endif
#if defined(CONFIG_MMC) || defined(CONFIG_MMC_MODULE)
-static int cmx270_mci_init(struct device *dev,
- irq_handler_t cmx270_detect_int,
- void *data)
+static struct pxamci_platform_data cmx270_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = GPIO83_MMC_IRQ,
+ .gpio_card_ro = -1,
+ .gpio_power = GPIO105_MMC_POWER,
+ .gpio_power_invert = 1,
+};
+
+static void __init cmx270_init_mmc(void)
{
- int err;
+ pxa_set_mci_info(&cmx270_mci_platform_data);
+}
+#else
+static inline void cmx270_init_mmc(void) {}
+#endif
+
+#if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
+static struct pxa2xx_spi_master cm_x270_spi_info = {
+ .num_chipselect = 1,
+ .enable_dma = 1,
+};
+
+static struct pxa2xx_spi_chip cm_x270_libertas_chip = {
+ .rx_threshold = 1,
+ .tx_threshold = 1,
+ .timeout = 1000,
+ .gpio_cs = 14,
+};
+
+static unsigned long cm_x270_libertas_pin_config[] = {
+ /* SSP2 */
+ GPIO19_SSP2_SCLK,
+ GPIO14_GPIO,
+ GPIO87_SSP2_TXD,
+ GPIO88_SSP2_RXD,
+
+};
- err = gpio_request(GPIO105_MMC_POWER, "MMC/SD power");
- if (err) {
- dev_warn(dev, "power gpio unavailable\n");
+static int cm_x270_libertas_setup(struct spi_device *spi)
+{
+ int err = gpio_request(GPIO19_WLAN_STRAP, "WLAN STRAP");
+ if (err)
return err;
- }
- gpio_direction_output(GPIO105_MMC_POWER, 0);
+ err = gpio_request(GPIO102_WLAN_RST, "WLAN RST");
+ if (err)
+ goto err_free_strap;
- err = request_irq(CMX270_MMC_IRQ, cmx270_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- gpio_free(GPIO105_MMC_POWER);
- dev_err(dev, "cmx270_mci_init: MMC/SD: can't"
- " request MMC card detect IRQ\n");
- }
+ err = gpio_direction_output(GPIO102_WLAN_RST, 0);
+ if (err)
+ goto err_free_strap;
+ msleep(100);
+
+ err = gpio_direction_output(GPIO19_WLAN_STRAP, 1);
+ if (err)
+ goto err_free_strap;
+ msleep(100);
+
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(cm_x270_libertas_pin_config));
+
+ gpio_set_value(GPIO102_WLAN_RST, 1);
+ msleep(100);
+
+ spi->bits_per_word = 16;
+ spi_setup(spi);
+
+ return 0;
+
+err_free_strap:
+ gpio_free(GPIO19_WLAN_STRAP);
return err;
}
-static void cmx270_mci_setpower(struct device *dev, unsigned int vdd)
+static int cm_x270_libertas_teardown(struct spi_device *spi)
{
- struct pxamci_platform_data *p_d = dev->platform_data;
-
- if ((1 << vdd) & p_d->ocr_mask) {
- dev_dbg(dev, "power on\n");
- gpio_set_value(GPIO105_MMC_POWER, 0);
- } else {
- gpio_set_value(GPIO105_MMC_POWER, 1);
- dev_dbg(dev, "power off\n");
- }
-}
+ gpio_set_value(GPIO102_WLAN_RST, 0);
+ gpio_free(GPIO102_WLAN_RST);
+ gpio_free(GPIO19_WLAN_STRAP);
-static void cmx270_mci_exit(struct device *dev, void *data)
-{
- free_irq(CMX270_MMC_IRQ, data);
- gpio_free(GPIO105_MMC_POWER);
+ return 0;
}
-static struct pxamci_platform_data cmx270_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cmx270_mci_init,
- .setpower = cmx270_mci_setpower,
- .exit = cmx270_mci_exit,
+struct libertas_spi_platform_data cm_x270_libertas_pdata = {
+ .use_dummy_writes = 1,
+ .setup = cm_x270_libertas_setup,
+ .teardown = cm_x270_libertas_teardown,
};
-static void __init cmx270_init_mmc(void)
+static struct spi_board_info cm_x270_spi_devices[] __initdata = {
+ {
+ .modalias = "libertas_spi",
+ .max_speed_hz = 13000000,
+ .bus_num = 2,
+ .irq = gpio_to_irq(95),
+ .chip_select = 0,
+ .controller_data = &cm_x270_libertas_chip,
+ .platform_data = &cm_x270_libertas_pdata,
+ },
+};
+
+static void __init cmx270_init_spi(void)
{
- pxa_set_mci_info(&cmx270_mci_platform_data);
+ pxa2xx_set_spi_info(2, &cm_x270_spi_info);
+ spi_register_board_info(ARRAY_AND_SIZE(cm_x270_spi_devices));
}
#else
-static inline void cmx270_init_mmc(void) {}
+static inline void cmx270_init_spi(void) {}
#endif
void __init cmx270_init(void)
cmx270_init_mmc();
cmx270_init_ohci();
cmx270_init_2700G();
+ cmx270_init_spi();
}
}
static struct pxamci_platform_data cm_x300_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cm_x300_mci_init,
- .exit = cm_x300_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = cm_x300_mci_init,
+ .exit = cm_x300_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
-static int cm_x300_mci2_ro(struct device *dev)
-{
- return gpio_get_value(GPIO85_MMC2_WP);
-}
-
-static int cm_x300_mci2_init(struct device *dev,
- irq_handler_t cm_x300_detect_int,
- void *data)
-{
- int err;
-
- /*
- * setup GPIO for CM-X300 MMC controller
- */
- err = gpio_request(GPIO82_MMC2_IRQ, "mmc card detect");
- if (err)
- goto err_request_cd;
- gpio_direction_input(GPIO82_MMC2_IRQ);
-
- err = gpio_request(GPIO85_MMC2_WP, "mmc write protect");
- if (err)
- goto err_request_wp;
- gpio_direction_input(GPIO85_MMC2_WP);
-
- err = request_irq(CM_X300_MMC2_IRQ, cm_x300_detect_int,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: MMC/SD/SDIO: "
- "can't request card detect IRQ\n", __func__);
- goto err_request_irq;
- }
-
- return 0;
-
-err_request_irq:
- gpio_free(GPIO85_MMC2_WP);
-err_request_wp:
- gpio_free(GPIO82_MMC2_IRQ);
-err_request_cd:
- return err;
-}
-
-static void cm_x300_mci2_exit(struct device *dev, void *data)
-{
- free_irq(CM_X300_MMC2_IRQ, data);
- gpio_free(GPIO82_MMC2_IRQ);
- gpio_free(GPIO85_MMC2_WP);
-}
-
static struct pxamci_platform_data cm_x300_mci2_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = cm_x300_mci2_init,
- .exit = cm_x300_mci2_exit,
- .get_ro = cm_x300_mci2_ro,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = GPIO82_MMC2_IRQ,
+ .gpio_card_ro = GPIO85_MMC2_WP,
+ .gpio_power = -1,
};
static void __init cm_x300_init_mmc(void)
{
colibri_pxa300_init_eth();
colibri_pxa300_init_ohci();
+ colibri_pxa3xx_init_nand();
colibri_pxa300_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO39_GPIO));
colibri_pxa310_init_ac97();
static inline void colibri_pxa320_init_ac97(void) {}
#endif
+/*
+ * The following configuration is verified to work with the Toradex Orchid
+ * carrier board
+ */
+static mfp_cfg_t colibri_pxa320_uart_pin_config[] __initdata = {
+ /* UART 1 configuration (may be set by bootloader) */
+ GPIO99_UART1_CTS,
+ GPIO104_UART1_RTS,
+ GPIO97_UART1_RXD,
+ GPIO98_UART1_TXD,
+ GPIO101_UART1_DTR,
+ GPIO103_UART1_DSR,
+ GPIO100_UART1_DCD,
+ GPIO102_UART1_RI,
+
+ /* UART 2 configuration */
+ GPIO109_UART2_CTS,
+ GPIO112_UART2_RTS,
+ GPIO110_UART2_RXD,
+ GPIO111_UART2_TXD,
+
+ /* UART 3 configuration */
+ GPIO30_UART3_RXD,
+ GPIO31_UART3_TXD,
+};
+
+static void __init colibri_pxa320_init_uart(void)
+{
+ pxa3xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa320_uart_pin_config));
+}
+
void __init colibri_pxa320_init(void)
{
colibri_pxa320_init_eth();
colibri_pxa320_init_ohci();
+ colibri_pxa3xx_init_nand();
colibri_pxa320_init_lcd();
colibri_pxa3xx_init_lcd(mfp_to_gpio(GPIO49_GPIO));
colibri_pxa320_init_ac97();
colibri_pxa3xx_init_mmc(ARRAY_AND_SIZE(colibri_pxa320_mmc_pin_config),
mfp_to_gpio(MFP_PIN_GPIO28));
+ colibri_pxa320_init_uart();
}
MACHINE_START(COLIBRI320, "Toradex Colibri PXA320")
#include <mach/colibri.h>
#include <mach/mmc.h>
#include <mach/pxafb.h>
+#include <mach/pxa3xx_nand.h>
#include "generic.h"
#include "devices.h"
}
static struct pxamci_platform_data colibri_pxa3xx_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = colibri_pxa3xx_mci_init,
- .exit = colibri_pxa3xx_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = colibri_pxa3xx_mci_init,
+ .exit = colibri_pxa3xx_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
void __init colibri_pxa3xx_init_mmc(mfp_cfg_t *pins, int len, int detect_pin)
}
#endif
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+static struct mtd_partition colibri_nand_partitions[] = {
+ {
+ .name = "bootloader",
+ .offset = 0,
+ .size = SZ_512K,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "kernel",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_4M,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "reserved",
+ .offset = MTDPART_OFS_APPEND,
+ .size = SZ_1M,
+ .mask_flags = MTD_WRITEABLE, /* force read-only */
+ },
+ {
+ .name = "fs",
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct pxa3xx_nand_platform_data colibri_nand_info = {
+ .enable_arbiter = 1,
+ .keep_config = 1,
+ .parts = colibri_nand_partitions,
+ .nr_parts = ARRAY_SIZE(colibri_nand_partitions),
+};
+
+void __init colibri_pxa3xx_init_nand(void)
+{
+ pxa3xx_set_nand_info(&colibri_nand_info);
+}
+#endif
+
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
#include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
#include <video/w100fb.h>
#include <asm/setup.h>
GPIO6_MMC_CLK,
GPIO8_MMC_CS0,
+ /* GPIO Matrix Keypad */
+ GPIO66_GPIO, /* column 0 */
+ GPIO67_GPIO, /* column 1 */
+ GPIO68_GPIO, /* column 2 */
+ GPIO69_GPIO, /* column 3 */
+ GPIO70_GPIO, /* column 4 */
+ GPIO71_GPIO, /* column 5 */
+ GPIO72_GPIO, /* column 6 */
+ GPIO73_GPIO, /* column 7 */
+ GPIO74_GPIO, /* column 8 */
+ GPIO75_GPIO, /* column 9 */
+ GPIO76_GPIO, /* column 10 */
+ GPIO77_GPIO, /* column 11 */
+ GPIO58_GPIO, /* row 0 */
+ GPIO59_GPIO, /* row 1 */
+ GPIO60_GPIO, /* row 2 */
+ GPIO61_GPIO, /* row 3 */
+ GPIO62_GPIO, /* row 4 */
+ GPIO63_GPIO, /* row 5 */
+ GPIO64_GPIO, /* row 6 */
+ GPIO65_GPIO, /* row 7 */
+
/* GPIO */
GPIO9_GPIO, /* CORGI_GPIO_nSD_DETECT */
GPIO7_GPIO, /* CORGI_GPIO_nSD_WP */
/*
* Corgi Keyboard Device
*/
+#define CORGI_KEY_CALENDER KEY_F1
+#define CORGI_KEY_ADDRESS KEY_F2
+#define CORGI_KEY_FN KEY_F3
+#define CORGI_KEY_CANCEL KEY_F4
+#define CORGI_KEY_OFF KEY_SUSPEND
+#define CORGI_KEY_EXOK KEY_F5
+#define CORGI_KEY_EXCANCEL KEY_F6
+#define CORGI_KEY_EXJOGDOWN KEY_F7
+#define CORGI_KEY_EXJOGUP KEY_F8
+#define CORGI_KEY_JAP1 KEY_LEFTCTRL
+#define CORGI_KEY_JAP2 KEY_LEFTALT
+#define CORGI_KEY_MAIL KEY_F10
+#define CORGI_KEY_OK KEY_F11
+#define CORGI_KEY_MENU KEY_F12
+
+static const uint32_t corgikbd_keymap[] = {
+ KEY(0, 1, KEY_1),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_5),
+ KEY(0, 4, KEY_6),
+ KEY(0, 5, KEY_7),
+ KEY(0, 6, KEY_9),
+ KEY(0, 7, KEY_0),
+ KEY(0, 8, KEY_BACKSPACE),
+ KEY(1, 1, KEY_2),
+ KEY(1, 2, KEY_4),
+ KEY(1, 3, KEY_R),
+ KEY(1, 4, KEY_Y),
+ KEY(1, 5, KEY_8),
+ KEY(1, 6, KEY_I),
+ KEY(1, 7, KEY_O),
+ KEY(1, 8, KEY_P),
+ KEY(2, 0, KEY_TAB),
+ KEY(2, 1, KEY_Q),
+ KEY(2, 2, KEY_E),
+ KEY(2, 3, KEY_T),
+ KEY(2, 4, KEY_G),
+ KEY(2, 5, KEY_U),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_K),
+ KEY(3, 0, CORGI_KEY_CALENDER),
+ KEY(3, 1, KEY_W),
+ KEY(3, 2, KEY_S),
+ KEY(3, 3, KEY_F),
+ KEY(3, 4, KEY_V),
+ KEY(3, 5, KEY_H),
+ KEY(3, 6, KEY_M),
+ KEY(3, 7, KEY_L),
+ KEY(3, 9, KEY_RIGHTSHIFT),
+ KEY(4, 0, CORGI_KEY_ADDRESS),
+ KEY(4, 1, KEY_A),
+ KEY(4, 2, KEY_D),
+ KEY(4, 3, KEY_C),
+ KEY(4, 4, KEY_B),
+ KEY(4, 5, KEY_N),
+ KEY(4, 6, KEY_DOT),
+ KEY(4, 8, KEY_ENTER),
+ KEY(4, 10, KEY_LEFTSHIFT),
+ KEY(5, 0, CORGI_KEY_MAIL),
+ KEY(5, 1, KEY_Z),
+ KEY(5, 2, KEY_X),
+ KEY(5, 3, KEY_MINUS),
+ KEY(5, 4, KEY_SPACE),
+ KEY(5, 5, KEY_COMMA),
+ KEY(5, 7, KEY_UP),
+ KEY(5, 11, CORGI_KEY_FN),
+ KEY(6, 0, KEY_SYSRQ),
+ KEY(6, 1, CORGI_KEY_JAP1),
+ KEY(6, 2, CORGI_KEY_JAP2),
+ KEY(6, 3, CORGI_KEY_CANCEL),
+ KEY(6, 4, CORGI_KEY_OK),
+ KEY(6, 5, CORGI_KEY_MENU),
+ KEY(6, 6, KEY_LEFT),
+ KEY(6, 7, KEY_DOWN),
+ KEY(6, 8, KEY_RIGHT),
+ KEY(7, 0, CORGI_KEY_OFF),
+ KEY(7, 1, CORGI_KEY_EXOK),
+ KEY(7, 2, CORGI_KEY_EXCANCEL),
+ KEY(7, 3, CORGI_KEY_EXJOGDOWN),
+ KEY(7, 4, CORGI_KEY_EXJOGUP),
+};
+
+static struct matrix_keymap_data corgikbd_keymap_data = {
+ .keymap = corgikbd_keymap,
+ .keymap_size = ARRAY_SIZE(corgikbd_keymap),
+};
+
+static const int corgikbd_row_gpios[] =
+ { 58, 59, 60, 61, 62, 63, 64, 65 };
+static const int corgikbd_col_gpios[] =
+ { 66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77 };
+
+static struct matrix_keypad_platform_data corgikbd_pdata = {
+ .keymap_data = &corgikbd_keymap_data,
+ .row_gpios = corgikbd_row_gpios,
+ .col_gpios = corgikbd_col_gpios,
+ .num_row_gpios = ARRAY_SIZE(corgikbd_row_gpios),
+ .num_col_gpios = ARRAY_SIZE(corgikbd_col_gpios),
+ .col_scan_delay_us = 10,
+ .debounce_ms = 10,
+ .wakeup = 1,
+};
+
static struct platform_device corgikbd_device = {
- .name = "corgi-keyboard",
+ .name = "matrix-keypad",
.id = -1,
+ .dev = {
+ .platform_data = &corgikbd_pdata,
+ },
};
/*
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-static struct pxamci_platform_data corgi_mci_platform_data;
-
-static int corgi_mci_init(struct device *dev, irq_handler_t corgi_detect_int, void *data)
-{
- int err;
-
- err = gpio_request(CORGI_GPIO_nSD_DETECT, "nSD_DETECT");
- if (err)
- goto err_out;
-
- err = gpio_request(CORGI_GPIO_nSD_WP, "nSD_WP");
- if (err)
- goto err_free_1;
-
- err = gpio_request(CORGI_GPIO_SD_PWR, "SD_PWR");
- if (err)
- goto err_free_2;
-
- gpio_direction_input(CORGI_GPIO_nSD_DETECT);
- gpio_direction_input(CORGI_GPIO_nSD_WP);
- gpio_direction_output(CORGI_GPIO_SD_PWR, 0);
-
- corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = request_irq(CORGI_IRQ_GPIO_nSD_DETECT, corgi_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING |
- IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
- __func__);
- goto err_free_3;
- }
- return 0;
-
-err_free_3:
- gpio_free(CORGI_GPIO_SD_PWR);
-err_free_2:
- gpio_free(CORGI_GPIO_nSD_WP);
-err_free_1:
- gpio_free(CORGI_GPIO_nSD_DETECT);
-err_out:
- return err;
-}
-
-static void corgi_mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data* p_d = dev->platform_data;
-
- gpio_set_value(CORGI_GPIO_SD_PWR, ((1 << vdd) & p_d->ocr_mask));
-}
-
-static int corgi_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(CORGI_GPIO_nSD_WP);
-}
-
-static void corgi_mci_exit(struct device *dev, void *data)
-{
- free_irq(CORGI_IRQ_GPIO_nSD_DETECT, data);
- gpio_free(CORGI_GPIO_SD_PWR);
- gpio_free(CORGI_GPIO_nSD_WP);
- gpio_free(CORGI_GPIO_nSD_DETECT);
-}
-
static struct pxamci_platform_data corgi_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = corgi_mci_init,
- .get_ro = corgi_mci_get_ro,
- .setpower = corgi_mci_setpower,
- .exit = corgi_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = CORGI_GPIO_nSD_WP,
+ .gpio_power = CORGI_GPIO_SD_PWR,
};
/*
* Irda
*/
-static void corgi_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(CORGI_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int corgi_irda_startup(struct device *dev)
-{
- int err;
-
- err = gpio_request(CORGI_GPIO_IR_ON, "IR_ON");
- if (err)
- return err;
-
- gpio_direction_output(CORGI_GPIO_IR_ON, 1);
- return 0;
-}
-
-static void corgi_irda_shutdown(struct device *dev)
-{
- gpio_free(CORGI_GPIO_IR_ON);
-}
-
static struct pxaficp_platform_data corgi_ficp_platform_data = {
+ .gpio_pwdown = CORGI_GPIO_IR_ON,
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = corgi_irda_transceiver_mode,
- .startup = corgi_irda_startup,
- .shutdown = corgi_irda_shutdown,
};
corgi_init_spi();
pxa_set_udc_info(&udc_info);
+ corgi_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&corgi_mci_platform_data);
pxa_set_ficp_info(&corgi_ficp_platform_data);
pxa_set_i2c_info(NULL);
static int csb726_mci_init(struct device *dev,
irq_handler_t detect, void *data)
{
- int err;
-
csb726_mci_data.detect_delay = msecs_to_jiffies(500);
-
- err = gpio_request(CSB726_GPIO_MMC_DETECT, "MMC detect");
- if (err)
- goto err_det_req;
-
- err = gpio_direction_input(CSB726_GPIO_MMC_DETECT);
- if (err)
- goto err_det_dir;
-
- err = gpio_request(CSB726_GPIO_MMC_RO, "MMC ro");
- if (err)
- goto err_ro_req;
-
- err = gpio_direction_input(CSB726_GPIO_MMC_RO);
- if (err)
- goto err_ro_dir;
-
- err = request_irq(gpio_to_irq(CSB726_GPIO_MMC_DETECT), detect,
- IRQF_DISABLED, "MMC card detect", data);
- if (err)
- goto err_irq;
-
return 0;
-
-err_irq:
-err_ro_dir:
- gpio_free(CSB726_GPIO_MMC_RO);
-err_ro_req:
-err_det_dir:
- gpio_free(CSB726_GPIO_MMC_DETECT);
-err_det_req:
- return err;
-}
-
-static int csb726_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(CSB726_GPIO_MMC_RO);
-}
-
-static void csb726_mci_exit(struct device *dev, void *data)
-{
- free_irq(gpio_to_irq(CSB726_GPIO_MMC_DETECT), data);
- gpio_free(CSB726_GPIO_MMC_RO);
- gpio_free(CSB726_GPIO_MMC_DETECT);
}
static struct pxamci_platform_data csb726_mci = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = csb726_mci_init,
- .get_ro = csb726_mci_get_ro,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = csb726_mci_init,
/* FIXME setpower */
- .exit = csb726_mci_exit,
+ .gpio_card_detect = CSB726_GPIO_MMC_DETECT,
+ .gpio_card_ro = CSB726_GPIO_MMC_RO,
+ .gpio_power = -1,
};
static struct pxaohci_platform_data csb726_ohci_platform_data = {
{
pxa_register_device(&pxa3xx_device_nand, info);
}
+
+static struct resource pxa3xx_resources_gcu[] = {
+ {
+ .start = 0x54000000,
+ .end = 0x54000fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_GCU,
+ .end = IRQ_GCU,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static u64 pxa3xx_gcu_dmamask = DMA_BIT_MASK(32);
+
+struct platform_device pxa3xx_device_gcu = {
+ .name = "pxa3xx-gcu",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(pxa3xx_resources_gcu),
+ .resource = pxa3xx_resources_gcu,
+ .dev = {
+ .dma_mask = &pxa3xx_gcu_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ },
+};
+
#endif /* CONFIG_PXA3xx */
/* pxa2xx-spi platform-device ID equals respective SSP platform-device ID + 1.
extern struct platform_device pxa3xx_device_nand;
extern struct platform_device pxa3xx_device_i2c_power;
+extern struct platform_device pxa3xx_device_gcu;
+
void __init pxa_register_device(struct platform_device *dev, void *data);
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_udc_info(&e7xx_udc_mach_info);
pxa_set_ac97_info(NULL);
- e7xx_irda_init();
pxa_set_ficp_info(&e7xx_ficp_platform_data);
}
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_udc_info(&e7xx_udc_mach_info);
pxa_set_ac97_info(NULL);
- e7xx_irda_init();
pxa_set_ficp_info(&e7xx_ficp_platform_data);
}
}
static struct pxamci_platform_data em_x270_mci_platform_data = {
- .ocr_mask = MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
- MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
- MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
- MMC_VDD_30_31|MMC_VDD_31_32,
- .init = em_x270_mci_init,
- .setpower = em_x270_mci_setpower,
- .exit = em_x270_mci_exit,
+ .ocr_mask = MMC_VDD_20_21|MMC_VDD_21_22|MMC_VDD_22_23|
+ MMC_VDD_24_25|MMC_VDD_25_26|MMC_VDD_26_27|
+ MMC_VDD_27_28|MMC_VDD_28_29|MMC_VDD_29_30|
+ MMC_VDD_30_31|MMC_VDD_31_32,
+ .init = em_x270_mci_init,
+ .setpower = em_x270_mci_setpower,
+ .exit = em_x270_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init em_x270_init_mmc(void)
return 0;
}
-static struct soc_camera_link iclink = {
- .bus_id = 0,
- .power = em_x270_sensor_power,
-};
-
static struct i2c_board_info em_x270_i2c_cam_info[] = {
{
I2C_BOARD_INFO("mt9m111", 0x48),
+ },
+};
+
+static struct soc_camera_link iclink = {
+ .bus_id = 0,
+ .power = em_x270_sensor_power,
+ .board_info = &em_x270_i2c_cam_info[0],
+ .i2c_adapter_id = 0,
+ .module_name = "mt9m111",
+};
+
+static struct platform_device em_x270_camera = {
+ .name = "soc-camera-pdrv",
+ .id = -1,
+ .dev = {
.platform_data = &iclink,
},
};
static void __init em_x270_init_camera(void)
{
- i2c_register_board_info(0, ARRAY_AND_SIZE(em_x270_i2c_cam_info));
pxa_set_camera_info(&em_x270_camera_platform_data);
+ platform_device_register(&em_x270_camera);
}
#else
static inline void em_x270_init_camera(void) {}
REGULATOR_CONSUMER(ldo10, &pxa_device_mci.dev, "vcc sdio");
REGULATOR_CONSUMER(ldo12, NULL, "vcc usb");
REGULATOR_CONSUMER(ldo19, &em_x270_gprs_userspace_consumer.dev, "vcc gprs");
+REGULATOR_CONSUMER(buck2, NULL, "vcc_core");
#define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask) \
static struct regulator_init_data _ldo##_data = { \
REGULATOR_CHANGE_STATUS | REGULATOR_CHANGE_VOLTAGE);
REGULATOR_INIT(ldo12, 3000000, 3000000, REGULATOR_CHANGE_STATUS);
REGULATOR_INIT(ldo19, 3200000, 3200000, REGULATOR_CHANGE_STATUS);
+REGULATOR_INIT(buck2, 1000000, 1650000, REGULATOR_CHANGE_VOLTAGE);
struct led_info em_x270_led_info = {
.name = "em-x270:orange",
DA9030_LDO(12),
DA9030_LDO(19),
+ DA9030_SUBDEV(regulator, BUCK2, &buck2_data),
+
DA9030_SUBDEV(led, LED_PC, &em_x270_led_info),
DA9030_SUBDEV(backlight, WLED, &em_x270_led_info),
DA9030_SUBDEV(battery, BAT, &em_x270_batterty_info),
static void __init em_x270_module_init(void)
{
- pr_info("%s\n", __func__);
pxa2xx_mfp_config(ARRAY_AND_SIZE(em_x270_pin_config));
mmc_cd = GPIO13_MMC_CD;
static void __init em_x270_exeda_init(void)
{
- pr_info("%s\n", __func__);
pxa2xx_mfp_config(ARRAY_AND_SIZE(exeda_pin_config));
mmc_cd = GPIO114_MMC_CD;
.gpio_pullup_inverted = 1
};
-static void e7xx_irda_transceiver_mode(struct device *dev, int mode)
-{
- if (mode & IR_OFF) {
- gpio_set_value(GPIO_E7XX_IR_OFF, 1);
- pxa2xx_transceiver_mode(dev, mode);
- } else {
- pxa2xx_transceiver_mode(dev, mode);
- gpio_set_value(GPIO_E7XX_IR_OFF, 0);
- }
-}
-
-int e7xx_irda_init(void)
-{
- int ret;
-
- ret = gpio_request(GPIO_E7XX_IR_OFF, "IrDA power");
- if (ret)
- goto out;
-
- ret = gpio_direction_output(GPIO_E7XX_IR_OFF, 0);
- if (ret)
- goto out;
-
- e7xx_irda_transceiver_mode(NULL, IR_SIRMODE | IR_OFF);
-out:
- return ret;
-}
-
-static void e7xx_irda_shutdown(struct device *dev)
-{
- e7xx_irda_transceiver_mode(dev, IR_SIRMODE | IR_OFF);
- gpio_free(GPIO_E7XX_IR_OFF);
-}
-
struct pxaficp_platform_data e7xx_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = e7xx_irda_transceiver_mode,
- .shutdown = e7xx_irda_shutdown,
+ .gpio_pwdown = GPIO_E7XX_IR_OFF,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
int eseries_tmio_enable(struct platform_device *dev)
#ifdef CONFIG_MMC_PXA
static struct pxamci_platform_data gumstix_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init gumstix_mmc_init(void)
#include <mach/irda.h>
#include <mach/pxa2xx_spi.h>
+#include <video/platform_lcd.h>
#include <video/w100fb.h>
#include "devices.h"
* IRDA
*/
-static void irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO105_HX4700_nIR_ON, mode & IR_OFF);
-}
-
static struct pxaficp_platform_data ficp_info = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = irda_transceiver_mode,
+ .gpio_pwdown = GPIO105_HX4700_nIR_ON,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/*
* LCD - Sony display connected to ATI Imageon w3220
*/
-static int lcd_power;
-
static void sony_lcd_init(void)
{
gpio_set_value(GPIO84_HX4700_LCD_SQN, 1);
gpio_set_value(GPIO110_HX4700_LCD_LVDD_3V3_ON, 0);
}
-static int hx4700_lcd_set_power(struct lcd_device *ldev, int level)
-{
- switch (level) {
- case FB_BLANK_UNBLANK:
- sony_lcd_init();
- break;
- case FB_BLANK_NORMAL:
- case FB_BLANK_VSYNC_SUSPEND:
- case FB_BLANK_HSYNC_SUSPEND:
- case FB_BLANK_POWERDOWN:
- sony_lcd_off();
- break;
- }
- lcd_power = level;
- return 0;
-}
-
-static int hx4700_lcd_get_power(struct lcd_device *lm)
-{
- return lcd_power;
-}
-
-static struct lcd_ops hx4700_lcd_ops = {
- .get_power = hx4700_lcd_get_power,
- .set_power = hx4700_lcd_set_power,
-};
-
-static struct lcd_device *hx4700_lcd_device;
-
#ifdef CONFIG_PM
static void w3220_lcd_suspend(struct w100fb_par *wfb)
{
.resource = w3220_resources,
};
+static void hx4700_lcd_set_power(struct plat_lcd_data *pd, unsigned int power)
+{
+ if (power)
+ sony_lcd_init();
+ else
+ sony_lcd_off();
+}
+
+static struct plat_lcd_data hx4700_lcd_data = {
+ .set_power = hx4700_lcd_set_power,
+};
+
+static struct platform_device hx4700_lcd = {
+ .name = "platform-lcd",
+ .id = -1,
+ .dev = {
+ .platform_data = &hx4700_lcd_data,
+ .parent = &w3220.dev,
+ },
+};
+
/*
* Backlight
*/
pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));
- hx4700_lcd_device = lcd_device_register("w100fb", NULL,
- (void *)&w3220_info, &hx4700_lcd_ops);
-
gpio_set_value(GPIO71_HX4700_ASIC3_nRESET, 0);
mdelay(10);
gpio_set_value(GPIO71_HX4700_ASIC3_nRESET, 1);
};
static struct pxamci_platform_data idp_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init idp_init(void)
static struct pxamci_platform_data imote2_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
.get_ro = imote2_mci_get_ro,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static struct mtd_partition imote2flash_partitions[] = {
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-pxa/balloon3.h
+ *
+ * Authors: Nick Bane and Wookey
+ * Created: Oct, 2005
+ * Copyright: Toby Churchill Ltd
+ * Cribbed from mainstone.c, by Nicholas Pitre
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef ASM_ARCH_BALLOON3_H
+#define ASM_ARCH_BALLOON3_H
+
+enum balloon3_features {
+ BALLOON3_FEATURE_OHCI,
+ BALLOON3_FEATURE_MMC,
+ BALLOON3_FEATURE_CF,
+ BALLOON3_FEATURE_AUDIO,
+ BALLOON3_FEATURE_TOPPOLY,
+};
+
+#define BALLOON3_FPGA_PHYS PXA_CS4_PHYS
+#define BALLOON3_FPGA_VIRT (0xf1000000) /* as per balloon2 */
+#define BALLOON3_FPGA_LENGTH 0x01000000
+
+/* FPGA/CPLD registers */
+#define BALLOON3_PCMCIA0_REG (BALLOON3_FPGA_VIRT + 0x00e00008)
+/* fixme - same for now */
+#define BALLOON3_PCMCIA1_REG (BALLOON3_FPGA_VIRT + 0x00e00008)
+#define BALLOON3_NANDIO_IO_REG (BALLOON3_FPGA_VIRT + 0x00e00000)
+/* fpga/cpld interrupt control register */
+#define BALLOON3_INT_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e0000C)
+#define BALLOON3_NANDIO_CTL2_REG (BALLOON3_FPGA_VIRT + 0x00e00010)
+#define BALLOON3_NANDIO_CTL_REG (BALLOON3_FPGA_VIRT + 0x00e00014)
+#define BALLOON3_VERSION_REG (BALLOON3_FPGA_VIRT + 0x00e0001c)
+
+#define BALLOON3_SAMOSA_ADDR_REG (BALLOON3_FPGA_VIRT + 0x00c00000)
+#define BALLOON3_SAMOSA_DATA_REG (BALLOON3_FPGA_VIRT + 0x00c00004)
+#define BALLOON3_SAMOSA_STATUS_REG (BALLOON3_FPGA_VIRT + 0x00c0001c)
+
+/* GPIOs for irqs */
+#define BALLOON3_GPIO_AUX_NIRQ (94)
+#define BALLOON3_GPIO_CODEC_IRQ (95)
+
+/* Timer and Idle LED locations */
+#define BALLOON3_GPIO_LED_NAND (9)
+#define BALLOON3_GPIO_LED_IDLE (10)
+
+/* backlight control */
+#define BALLOON3_GPIO_RUN_BACKLIGHT (99)
+
+#define BALLOON3_GPIO_S0_CD (105)
+
+/* FPGA Interrupt Mask/Acknowledge Register */
+#define BALLOON3_INT_S0_IRQ (1 << 0) /* PCMCIA 0 IRQ */
+#define BALLOON3_INT_S0_STSCHG (1 << 1) /* PCMCIA 0 status changed */
+
+/* CF Status Register */
+#define BALLOON3_PCMCIA_nIRQ (1 << 0) /* IRQ / ready signal */
+#define BALLOON3_PCMCIA_nSTSCHG_BVD1 (1 << 1)
+ /* VDD sense / card status changed */
+
+/* CF control register (write) */
+#define BALLOON3_PCMCIA_RESET (1 << 0) /* Card reset signal */
+#define BALLOON3_PCMCIA_ENABLE (1 << 1)
+#define BALLOON3_PCMCIA_ADD_ENABLE (1 << 2)
+
+/* CPLD (and FPGA) interface definitions */
+#define CPLD_LCD0_DATA_SET 0x00
+#define CPLD_LCD0_DATA_CLR 0x10
+#define CPLD_LCD0_COMMAND_SET 0x01
+#define CPLD_LCD0_COMMAND_CLR 0x11
+#define CPLD_LCD1_DATA_SET 0x02
+#define CPLD_LCD1_DATA_CLR 0x12
+#define CPLD_LCD1_COMMAND_SET 0x03
+#define CPLD_LCD1_COMMAND_CLR 0x13
+
+#define CPLD_MISC_SET 0x07
+#define CPLD_MISC_CLR 0x17
+#define CPLD_MISC_LOON_NRESET_BIT 0
+#define CPLD_MISC_LOON_UNSUSP_BIT 1
+#define CPLD_MISC_RUN_5V_BIT 2
+#define CPLD_MISC_CHG_D0_BIT 3
+#define CPLD_MISC_CHG_D1_BIT 4
+#define CPLD_MISC_DAC_NCS_BIT 5
+
+#define CPLD_LCD_SET 0x08
+#define CPLD_LCD_CLR 0x18
+#define CPLD_LCD_BACKLIGHT_EN_0_BIT 0
+#define CPLD_LCD_BACKLIGHT_EN_1_BIT 1
+#define CPLD_LCD_LED_RED_BIT 4
+#define CPLD_LCD_LED_GREEN_BIT 5
+#define CPLD_LCD_NRESET_BIT 7
+
+#define CPLD_LCD_RO_SET 0x09
+#define CPLD_LCD_RO_CLR 0x19
+#define CPLD_LCD_RO_LCD0_nWAIT_BIT 0
+#define CPLD_LCD_RO_LCD1_nWAIT_BIT 1
+
+#define CPLD_SERIAL_SET 0x0a
+#define CPLD_SERIAL_CLR 0x1a
+#define CPLD_SERIAL_GSM_RI_BIT 0
+#define CPLD_SERIAL_GSM_CTS_BIT 1
+#define CPLD_SERIAL_GSM_DTR_BIT 2
+#define CPLD_SERIAL_LPR_CTS_BIT 3
+#define CPLD_SERIAL_TC232_CTS_BIT 4
+#define CPLD_SERIAL_TC232_DSR_BIT 5
+
+#define CPLD_SROUTING_SET 0x0b
+#define CPLD_SROUTING_CLR 0x1b
+#define CPLD_SROUTING_MSP430_LPR 0
+#define CPLD_SROUTING_MSP430_TC232 1
+#define CPLD_SROUTING_MSP430_GSM 2
+#define CPLD_SROUTING_LOON_LPR (0 << 4)
+#define CPLD_SROUTING_LOON_TC232 (1 << 4)
+#define CPLD_SROUTING_LOON_GSM (2 << 4)
+
+#define CPLD_AROUTING_SET 0x0c
+#define CPLD_AROUTING_CLR 0x1c
+#define CPLD_AROUTING_MIC2PHONE_BIT 0
+#define CPLD_AROUTING_PHONE2INT_BIT 1
+#define CPLD_AROUTING_PHONE2EXT_BIT 2
+#define CPLD_AROUTING_LOONL2INT_BIT 3
+#define CPLD_AROUTING_LOONL2EXT_BIT 4
+#define CPLD_AROUTING_LOONR2PHONE_BIT 5
+#define CPLD_AROUTING_LOONR2INT_BIT 6
+#define CPLD_AROUTING_LOONR2EXT_BIT 7
+
+extern int balloon3_has(enum balloon3_features feature);
+
+#endif
extern void colibri_pxa3xx_init_eth(struct ax_plat_data *plat_data);
#endif
+#if defined(CONFIG_MTD_NAND_PXA3xx) || defined(CONFIG_MTD_NAND_PXA3xx_MODULE)
+extern void colibri_pxa3xx_init_nand(void);
+#else
+static inline void colibri_pxa3xx_init_nand(void) {}
+#endif
+
/* physical memory regions */
#define COLIBRI_SDRAM_BASE 0xa0000000 /* SDRAM region */
mov \tmp, \tmp, lsr #13
and \tmp, \tmp, #0x7 @ Core G
cmp \tmp, #1
- bhi 1004f
+ bhi 1002f
+ @ Core Generation 1 (PXA25x)
mov \base, #io_p2v(0x40000000) @ IIR Ctl = 0x40d00000
add \base, \base, #0x00d00000
ldr \irqstat, [\base, #0] @ ICIP
ldr \irqnr, [\base, #4] @ ICMR
- b 1002f
-1004:
- mrc p6, 0, \irqstat, c6, c0, 0 @ ICIP2
- mrc p6, 0, \irqnr, c7, c0, 0 @ ICMR2
ands \irqnr, \irqstat, \irqnr
- beq 1003f
+ beq 1001f
rsb \irqstat, \irqnr, #0
and \irqstat, \irqstat, \irqnr
clz \irqnr, \irqstat
- rsb \irqnr, \irqnr, #31
- add \irqnr, \irqnr, #(32 + PXA_IRQ(0))
+ rsb \irqnr, \irqnr, #(31 + PXA_IRQ(0))
b 1001f
-1003:
- mrc p6, 0, \irqstat, c0, c0, 0 @ ICIP
- mrc p6, 0, \irqnr, c1, c0, 0 @ ICMR
1002:
- ands \irqnr, \irqstat, \irqnr
+ @ Core Generation 2 (PXA27x) or Core Generation 3 (PXA3xx)
+ mrc p6, 0, \irqstat, c5, c0, 0 @ ICHP
+ tst \irqstat, #0x80000000
beq 1001f
- rsb \irqstat, \irqnr, #0
- and \irqstat, \irqstat, \irqnr
- clz \irqnr, \irqstat
- rsb \irqnr, \irqnr, #(31 + PXA_IRQ(0))
+ bic \irqstat, \irqstat, #0x80000000
+ mov \irqnr, \irqstat, lsr #16
1001:
.endm
#define __cpu_is_pxa935(id) (0)
#endif
+#ifdef CONFIG_CPU_PXA950
+#define __cpu_is_pxa950(id) \
+ ({ \
+ unsigned int _id = (id) >> 4 & 0xfff; \
+ id == 0x697; \
+ })
+#else
+#define __cpu_is_pxa950(id) (0)
+#endif
+
#define cpu_is_pxa210() \
({ \
__cpu_is_pxa210(read_cpuid_id()); \
__cpu_is_pxa935(id); \
})
+#define cpu_is_pxa950() \
+ ({ \
+ unsigned int id = read_cpuid(CPUID_ID); \
+ __cpu_is_pxa950(id); \
+ })
+
+
/*
* CPUID Core Generation Bit
* <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x
void (*transceiver_mode)(struct device *dev, int mode);
int (*startup)(struct device *dev);
void (*shutdown)(struct device *dev);
+ int gpio_pwdown; /* powerdown GPIO for the IrDA chip */
+ bool gpio_pwdown_inverted; /* gpio_pwdown is inverted */
};
extern void pxa_set_ficp_info(struct pxaficp_platform_data *info);
#ifdef CONFIG_PXA3xx
#define IRQ_SSP4 PXA_IRQ(13) /* SSP4 service request */
#define IRQ_CIR PXA_IRQ(34) /* Consumer IR */
+#define IRQ_COMM_WDT PXA_IRQ(35) /* Comm WDT interrupt */
#define IRQ_TSI PXA_IRQ(36) /* Touch Screen Interface (PXA320) */
#define IRQ_USIM2 PXA_IRQ(38) /* USIM2 Controller */
-#define IRQ_GRPHICS PXA_IRQ(39) /* Graphics Controller */
+#define IRQ_GCU PXA_IRQ(39) /* Graphics Controller */
#define IRQ_MMC2 PXA_IRQ(41) /* MMC2 Controller */
#define IRQ_1WIRE PXA_IRQ(44) /* 1-Wire Controller */
#define IRQ_NAND PXA_IRQ(45) /* NAND Controller */
#define IRQ_MMC3 PXA_IRQ(55) /* MMC3 Controller (PXA310) */
#endif
-#define PXA_GPIO_IRQ_BASE PXA_IRQ(64)
-#define PXA_GPIO_IRQ_NUM (128)
+#ifdef CONFIG_CPU_PXA935
+#define IRQ_U2O PXA_IRQ(64) /* USB OTG 2.0 Controller (PXA935) */
+#define IRQ_U2H PXA_IRQ(65) /* USB Host 2.0 Controller (PXA935) */
+
+#define IRQ_MMC3_PXA935 PXA_IRQ(72) /* MMC3 Controller (PXA935) */
+#define IRQ_MMC4_PXA935 PXA_IRQ(73) /* MMC4 Controller (PXA935) */
+#define IRQ_MMC5_PXA935 PXA_IRQ(74) /* MMC5 Controller (PXA935) */
+
+#define IRQ_U2P PXA_IRQ(93) /* USB PHY D+/D- Lines (PXA935) */
+#endif
+
+#ifdef CONFIG_CPU_PXA930
+#define IRQ_ENHROT PXA_IRQ(37) /* Enhanced Rotary (PXA930) */
+#define IRQ_ACIPC0 PXA_IRQ(5)
+#define IRQ_ACIPC1 PXA_IRQ(40)
+#define IRQ_ACIPC2 PXA_IRQ(19)
+#define IRQ_TRKBALL PXA_IRQ(43) /* Track Ball */
+#endif
+
+#ifdef CONFIG_CPU_PXA950
+#define IRQ_GC500 PXA_IRQ(70) /* Graphics Controller (PXA950) */
+#endif
+
+#define PXA_GPIO_IRQ_BASE PXA_IRQ(96)
+#define PXA_GPIO_IRQ_NUM (192)
#define GPIO_2_x_TO_IRQ(x) (PXA_GPIO_IRQ_BASE + (x))
#define IRQ_GPIO(x) (((x) < 2) ? (IRQ_GPIO0 + (x)) : GPIO_2_x_TO_IRQ(x))
#define IRQ_BOARD_END (IRQ_BOARD_START + 70)
#elif defined(CONFIG_MACH_ZYLONITE)
#define IRQ_BOARD_END (IRQ_BOARD_START + 32)
+#elif defined(CONFIG_PXA_EZX)
+#define IRQ_BOARD_END (IRQ_BOARD_START + 23)
#else
#define IRQ_BOARD_END (IRQ_BOARD_START + 16)
#endif
#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14)
#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15)
+/* Balloon3 Interrupts */
+#define BALLOON3_IRQ(x) (IRQ_BOARD_START + (x))
+
+#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0)
+#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1)
+
+#define BALLOON3_AUX_NIRQ IRQ_GPIO(BALLOON3_GPIO_AUX_NIRQ)
+#define BALLOON3_CODEC_IRQ IRQ_GPIO(BALLOON3_GPIO_CODEC_IRQ)
+#define BALLOON3_S0_CD_IRQ IRQ_GPIO(BALLOON3_GPIO_S0_CD)
+
/* LoCoMo Interrupts (CONFIG_SHARP_LOCOMO) */
#define IRQ_LOCOMO_KEY_BASE (IRQ_BOARD_START + 0)
#define IRQ_LOCOMO_GPIO_BASE (IRQ_BOARD_START + 1)
#ifndef __ASM_ARCH_MFP_H
#define __ASM_ARCH_MFP_H
-#define mfp_to_gpio(m) ((m) % 128)
-
-/* list of all the configurable MFP pins */
-enum {
- MFP_PIN_INVALID = -1,
-
- MFP_PIN_GPIO0 = 0,
- MFP_PIN_GPIO1,
- MFP_PIN_GPIO2,
- MFP_PIN_GPIO3,
- MFP_PIN_GPIO4,
- MFP_PIN_GPIO5,
- MFP_PIN_GPIO6,
- MFP_PIN_GPIO7,
- MFP_PIN_GPIO8,
- MFP_PIN_GPIO9,
- MFP_PIN_GPIO10,
- MFP_PIN_GPIO11,
- MFP_PIN_GPIO12,
- MFP_PIN_GPIO13,
- MFP_PIN_GPIO14,
- MFP_PIN_GPIO15,
- MFP_PIN_GPIO16,
- MFP_PIN_GPIO17,
- MFP_PIN_GPIO18,
- MFP_PIN_GPIO19,
- MFP_PIN_GPIO20,
- MFP_PIN_GPIO21,
- MFP_PIN_GPIO22,
- MFP_PIN_GPIO23,
- MFP_PIN_GPIO24,
- MFP_PIN_GPIO25,
- MFP_PIN_GPIO26,
- MFP_PIN_GPIO27,
- MFP_PIN_GPIO28,
- MFP_PIN_GPIO29,
- MFP_PIN_GPIO30,
- MFP_PIN_GPIO31,
- MFP_PIN_GPIO32,
- MFP_PIN_GPIO33,
- MFP_PIN_GPIO34,
- MFP_PIN_GPIO35,
- MFP_PIN_GPIO36,
- MFP_PIN_GPIO37,
- MFP_PIN_GPIO38,
- MFP_PIN_GPIO39,
- MFP_PIN_GPIO40,
- MFP_PIN_GPIO41,
- MFP_PIN_GPIO42,
- MFP_PIN_GPIO43,
- MFP_PIN_GPIO44,
- MFP_PIN_GPIO45,
- MFP_PIN_GPIO46,
- MFP_PIN_GPIO47,
- MFP_PIN_GPIO48,
- MFP_PIN_GPIO49,
- MFP_PIN_GPIO50,
- MFP_PIN_GPIO51,
- MFP_PIN_GPIO52,
- MFP_PIN_GPIO53,
- MFP_PIN_GPIO54,
- MFP_PIN_GPIO55,
- MFP_PIN_GPIO56,
- MFP_PIN_GPIO57,
- MFP_PIN_GPIO58,
- MFP_PIN_GPIO59,
- MFP_PIN_GPIO60,
- MFP_PIN_GPIO61,
- MFP_PIN_GPIO62,
- MFP_PIN_GPIO63,
- MFP_PIN_GPIO64,
- MFP_PIN_GPIO65,
- MFP_PIN_GPIO66,
- MFP_PIN_GPIO67,
- MFP_PIN_GPIO68,
- MFP_PIN_GPIO69,
- MFP_PIN_GPIO70,
- MFP_PIN_GPIO71,
- MFP_PIN_GPIO72,
- MFP_PIN_GPIO73,
- MFP_PIN_GPIO74,
- MFP_PIN_GPIO75,
- MFP_PIN_GPIO76,
- MFP_PIN_GPIO77,
- MFP_PIN_GPIO78,
- MFP_PIN_GPIO79,
- MFP_PIN_GPIO80,
- MFP_PIN_GPIO81,
- MFP_PIN_GPIO82,
- MFP_PIN_GPIO83,
- MFP_PIN_GPIO84,
- MFP_PIN_GPIO85,
- MFP_PIN_GPIO86,
- MFP_PIN_GPIO87,
- MFP_PIN_GPIO88,
- MFP_PIN_GPIO89,
- MFP_PIN_GPIO90,
- MFP_PIN_GPIO91,
- MFP_PIN_GPIO92,
- MFP_PIN_GPIO93,
- MFP_PIN_GPIO94,
- MFP_PIN_GPIO95,
- MFP_PIN_GPIO96,
- MFP_PIN_GPIO97,
- MFP_PIN_GPIO98,
- MFP_PIN_GPIO99,
- MFP_PIN_GPIO100,
- MFP_PIN_GPIO101,
- MFP_PIN_GPIO102,
- MFP_PIN_GPIO103,
- MFP_PIN_GPIO104,
- MFP_PIN_GPIO105,
- MFP_PIN_GPIO106,
- MFP_PIN_GPIO107,
- MFP_PIN_GPIO108,
- MFP_PIN_GPIO109,
- MFP_PIN_GPIO110,
- MFP_PIN_GPIO111,
- MFP_PIN_GPIO112,
- MFP_PIN_GPIO113,
- MFP_PIN_GPIO114,
- MFP_PIN_GPIO115,
- MFP_PIN_GPIO116,
- MFP_PIN_GPIO117,
- MFP_PIN_GPIO118,
- MFP_PIN_GPIO119,
- MFP_PIN_GPIO120,
- MFP_PIN_GPIO121,
- MFP_PIN_GPIO122,
- MFP_PIN_GPIO123,
- MFP_PIN_GPIO124,
- MFP_PIN_GPIO125,
- MFP_PIN_GPIO126,
- MFP_PIN_GPIO127,
- MFP_PIN_GPIO0_2,
- MFP_PIN_GPIO1_2,
- MFP_PIN_GPIO2_2,
- MFP_PIN_GPIO3_2,
- MFP_PIN_GPIO4_2,
- MFP_PIN_GPIO5_2,
- MFP_PIN_GPIO6_2,
- MFP_PIN_GPIO7_2,
- MFP_PIN_GPIO8_2,
- MFP_PIN_GPIO9_2,
- MFP_PIN_GPIO10_2,
- MFP_PIN_GPIO11_2,
- MFP_PIN_GPIO12_2,
- MFP_PIN_GPIO13_2,
- MFP_PIN_GPIO14_2,
- MFP_PIN_GPIO15_2,
- MFP_PIN_GPIO16_2,
- MFP_PIN_GPIO17_2,
-
- MFP_PIN_ULPI_STP,
- MFP_PIN_ULPI_NXT,
- MFP_PIN_ULPI_DIR,
-
- MFP_PIN_nXCVREN,
- MFP_PIN_DF_CLE_nOE,
- MFP_PIN_DF_nADV1_ALE,
- MFP_PIN_DF_SCLK_E,
- MFP_PIN_DF_SCLK_S,
- MFP_PIN_nBE0,
- MFP_PIN_nBE1,
- MFP_PIN_DF_nADV2_ALE,
- MFP_PIN_DF_INT_RnB,
- MFP_PIN_DF_nCS0,
- MFP_PIN_DF_nCS1,
- MFP_PIN_nLUA,
- MFP_PIN_nLLA,
- MFP_PIN_DF_nWE,
- MFP_PIN_DF_ALE_nWE,
- MFP_PIN_DF_nRE_nOE,
- MFP_PIN_DF_ADDR0,
- MFP_PIN_DF_ADDR1,
- MFP_PIN_DF_ADDR2,
- MFP_PIN_DF_ADDR3,
- MFP_PIN_DF_IO0,
- MFP_PIN_DF_IO1,
- MFP_PIN_DF_IO2,
- MFP_PIN_DF_IO3,
- MFP_PIN_DF_IO4,
- MFP_PIN_DF_IO5,
- MFP_PIN_DF_IO6,
- MFP_PIN_DF_IO7,
- MFP_PIN_DF_IO8,
- MFP_PIN_DF_IO9,
- MFP_PIN_DF_IO10,
- MFP_PIN_DF_IO11,
- MFP_PIN_DF_IO12,
- MFP_PIN_DF_IO13,
- MFP_PIN_DF_IO14,
- MFP_PIN_DF_IO15,
-
- /* additional pins on PXA930 */
- MFP_PIN_GSIM_UIO,
- MFP_PIN_GSIM_UCLK,
- MFP_PIN_GSIM_UDET,
- MFP_PIN_GSIM_nURST,
- MFP_PIN_PMIC_INT,
- MFP_PIN_RDY,
-
- MFP_PIN_MAX,
-};
-
-/*
- * a possible MFP configuration is represented by a 32-bit integer
- *
- * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
- * bit 10..12 - Alternate Function Selection
- * bit 13..15 - Drive Strength
- * bit 16..18 - Low Power Mode State
- * bit 19..20 - Low Power Mode Edge Detection
- * bit 21..22 - Run Mode Pull State
- *
- * to facilitate the definition, the following macros are provided
- *
- * MFP_CFG_DEFAULT - default MFP configuration value, with
- * alternate function = 0,
- * drive strength = fast 3mA (MFP_DS03X)
- * low power mode = default
- * edge detection = none
- *
- * MFP_CFG - default MFPR value with alternate function
- * MFP_CFG_DRV - default MFPR value with alternate function and
- * pin drive strength
- * MFP_CFG_LPM - default MFPR value with alternate function and
- * low power mode
- * MFP_CFG_X - default MFPR value with alternate function,
- * pin drive strength and low power mode
- */
-
-typedef unsigned long mfp_cfg_t;
-
-#define MFP_PIN(x) ((x) & 0x3ff)
-
-#define MFP_AF0 (0x0 << 10)
-#define MFP_AF1 (0x1 << 10)
-#define MFP_AF2 (0x2 << 10)
-#define MFP_AF3 (0x3 << 10)
-#define MFP_AF4 (0x4 << 10)
-#define MFP_AF5 (0x5 << 10)
-#define MFP_AF6 (0x6 << 10)
-#define MFP_AF7 (0x7 << 10)
-#define MFP_AF_MASK (0x7 << 10)
-#define MFP_AF(x) (((x) >> 10) & 0x7)
-
-#define MFP_DS01X (0x0 << 13)
-#define MFP_DS02X (0x1 << 13)
-#define MFP_DS03X (0x2 << 13)
-#define MFP_DS04X (0x3 << 13)
-#define MFP_DS06X (0x4 << 13)
-#define MFP_DS08X (0x5 << 13)
-#define MFP_DS10X (0x6 << 13)
-#define MFP_DS13X (0x7 << 13)
-#define MFP_DS_MASK (0x7 << 13)
-#define MFP_DS(x) (((x) >> 13) & 0x7)
-
-#define MFP_LPM_DEFAULT (0x0 << 16)
-#define MFP_LPM_DRIVE_LOW (0x1 << 16)
-#define MFP_LPM_DRIVE_HIGH (0x2 << 16)
-#define MFP_LPM_PULL_LOW (0x3 << 16)
-#define MFP_LPM_PULL_HIGH (0x4 << 16)
-#define MFP_LPM_FLOAT (0x5 << 16)
-#define MFP_LPM_INPUT (0x6 << 16)
-#define MFP_LPM_STATE_MASK (0x7 << 16)
-#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7)
-
-#define MFP_LPM_EDGE_NONE (0x0 << 19)
-#define MFP_LPM_EDGE_RISE (0x1 << 19)
-#define MFP_LPM_EDGE_FALL (0x2 << 19)
-#define MFP_LPM_EDGE_BOTH (0x3 << 19)
-#define MFP_LPM_EDGE_MASK (0x3 << 19)
-#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3)
-
-#define MFP_PULL_NONE (0x0 << 21)
-#define MFP_PULL_LOW (0x1 << 21)
-#define MFP_PULL_HIGH (0x2 << 21)
-#define MFP_PULL_BOTH (0x3 << 21)
-#define MFP_PULL_MASK (0x3 << 21)
-#define MFP_PULL(x) (((x) >> 21) & 0x3)
-
-#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
- MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
-
-#define MFP_CFG(pin, af) \
- ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
-
-#define MFP_CFG_DRV(pin, af, drv) \
- ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
-
-#define MFP_CFG_LPM(pin, af, lpm) \
- ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
-
-#define MFP_CFG_X(pin, af, drv, lpm) \
- ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
- (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
+#include <plat/mfp.h>
#endif /* __ASM_ARCH_MFP_H */
int (*get_ro)(struct device *);
void (*setpower)(struct device *, unsigned int);
void (*exit)(struct device *, void *);
+ int gpio_card_detect; /* gpio detecting card insertion */
+ int gpio_card_ro; /* gpio detecting read only toggle */
+ bool gpio_card_ro_invert; /* gpio ro is inverted */
+ int gpio_power; /* gpio powering up MMC bus */
+ bool gpio_power_invert; /* gpio power is inverted */
};
extern void pxa_set_mci_info(struct pxamci_platform_data *info);
--- /dev/null
+/*
+ * linux/include/asm-arm/arch-pxa/palmtc-gpio.h
+ *
+ * GPIOs and interrupts for Palm Tungsten|C Handheld Computer
+ *
+ * Authors: Alex Osborne <bobofdoom@gmail.com>
+ * Marek Vasut <marek.vasut@gmail.com>
+ * Holger Bocklet <bitz.email@gmx.net>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _INCLUDE_PALMTC_H_
+#define _INCLUDE_PALMTC_H_
+
+/** HERE ARE GPIOs **/
+
+/* GPIOs */
+#define GPIO_NR_PALMTC_EARPHONE_DETECT 2
+#define GPIO_NR_PALMTC_CRADLE_DETECT 5
+#define GPIO_NR_PALMTC_HOTSYNC_BUTTON 7
+
+/* SD/MMC */
+#define GPIO_NR_PALMTC_SD_DETECT_N 12
+#define GPIO_NR_PALMTC_SD_POWER 32
+#define GPIO_NR_PALMTC_SD_READONLY 54
+
+/* WLAN */
+#define GPIO_NR_PALMTC_PCMCIA_READY 13
+#define GPIO_NR_PALMTC_PCMCIA_PWRREADY 14
+#define GPIO_NR_PALMTC_PCMCIA_POWER1 15
+#define GPIO_NR_PALMTC_PCMCIA_POWER2 33
+#define GPIO_NR_PALMTC_PCMCIA_POWER3 55
+#define GPIO_NR_PALMTC_PCMCIA_RESET 78
+
+/* UDC */
+#define GPIO_NR_PALMTC_USB_DETECT_N 4
+#define GPIO_NR_PALMTC_USB_POWER 36
+
+/* LCD/BACKLIGHT */
+#define GPIO_NR_PALMTC_BL_POWER 16
+#define GPIO_NR_PALMTC_LCD_POWER 44
+#define GPIO_NR_PALMTC_LCD_BLANK 38
+
+/* UART */
+#define GPIO_NR_PALMTC_RS232_POWER 37
+
+/* IRDA */
+#define GPIO_NR_PALMTC_IR_DISABLE 45
+
+/* IRQs */
+#define IRQ_GPIO_PALMTC_SD_DETECT_N IRQ_GPIO(GPIO_NR_PALMTC_SD_DETECT_N)
+#define IRQ_GPIO_PALMTC_WLAN_READY IRQ_GPIO(GPIO_NR_PALMTC_WLAN_READY)
+
+/* UCB1400 GPIOs */
+#define GPIO_NR_PALMTC_POWER_DETECT (0x80 | 0x00)
+#define GPIO_NR_PALMTC_HEADPHONE_DETECT (0x80 | 0x01)
+#define GPIO_NR_PALMTC_SPEAKER_ENABLE (0x80 | 0x03)
+#define GPIO_NR_PALMTC_VIBRA_POWER (0x80 | 0x05)
+#define GPIO_NR_PALMTC_LED_POWER (0x80 | 0x07)
+
+/** HERE ARE INIT VALUES **/
+#define PALMTC_UCB1400_GPIO_OFFSET 0x80
+
+/* BATTERY */
+#define PALMTC_BAT_MAX_VOLTAGE 4000 /* 4.00V maximum voltage */
+#define PALMTC_BAT_MIN_VOLTAGE 3550 /* 3.55V critical voltage */
+#define PALMTC_BAT_MAX_CURRENT 0 /* unknokn */
+#define PALMTC_BAT_MIN_CURRENT 0 /* unknown */
+#define PALMTC_BAT_MAX_CHARGE 1 /* unknown */
+#define PALMTC_BAT_MIN_CHARGE 1 /* unknown */
+#define PALMTC_MAX_LIFE_MINS 240 /* on-life in minutes */
+
+#define PALMTC_BAT_MEASURE_DELAY (HZ * 1)
+
+/* BACKLIGHT */
+#define PALMTC_MAX_INTENSITY 0xFE
+#define PALMTC_DEFAULT_INTENSITY 0x7E
+#define PALMTC_LIMIT_MASK 0x7F
+#define PALMTC_PRESCALER 0x3F
+#define PALMTC_PERIOD_NS 3500
+
+#endif
#define PALMTX_PHYS_FLASH_START PXA_CS0_PHYS /* ChipSelect 0 */
#define PALMTX_PHYS_NAND_START PXA_CS1_PHYS /* ChipSelect 1 */
+#define PALMTX_NAND_ALE_PHYS (PALMTX_PHYS_NAND_START | (1 << 24))
+#define PALMTX_NAND_CLE_PHYS (PALMTX_PHYS_NAND_START | (1 << 25))
+#define PALMTX_NAND_ALE_VIRT 0xff100000
+#define PALMTX_NAND_CLE_VIRT 0xff200000
+
/* TOUCHSCREEN */
#define AC97_LINK_FRAME 21
#define CKEN_MVED 43 /* < MVED clock enable */
/* Note: GCU clock enable bit differs on PXA300/PXA310 and PXA320 */
-#define PXA300_CKEN_GRAPHICS 42 /* Graphics controller clock enable */
-#define PXA320_CKEN_GRAPHICS 7 /* Graphics controller clock enable */
+#define CKEN_PXA300_GCU 42 /* Graphics controller clock enable */
+#define CKEN_PXA320_GCU 7 /* Graphics controller clock enable */
#endif /* __ASM_ARCH_PXA3XX_REGS_H */
u_int fixed_modes:1,
cmap_inverse:1,
cmap_static:1,
- unused:29;
+ acceleration_enabled:1,
+ unused:28;
/* The following should be defined in LCCR0
* LCCR0_Act or LCCR0_Pas Active or Passive
#define ICFP __REG(0x40D0000C) /* Interrupt Controller FIQ Pending Register */
#define ICPR __REG(0x40D00010) /* Interrupt Controller Pending Register */
#define ICCR __REG(0x40D00014) /* Interrupt Controller Control Register */
+#define ICHP __REG(0x40D00018) /* Interrupt Controller Highest Priority Register */
#define ICIP2 __REG(0x40D0009C) /* Interrupt Controller IRQ Pending Register 2 */
#define ICMR2 __REG(0x40D000A0) /* Interrupt Controller Mask Register 2 */
#define ICFP2 __REG(0x40D000A8) /* Interrupt Controller FIQ Pending Register 2 */
#define ICPR2 __REG(0x40D000AC) /* Interrupt Controller Pending Register 2 */
+#define ICIP3 __REG(0x40D00130) /* Interrupt Controller IRQ Pending Register 3 */
+#define ICMR3 __REG(0x40D00134) /* Interrupt Controller Mask Register 3 */
+#define ICLR3 __REG(0x40D00138) /* Interrupt Controller Level Register 3 */
+#define ICFP3 __REG(0x40D0013C) /* Interrupt Controller FIQ Pending Register 3 */
+#define ICPR3 __REG(0x40D00140) /* Interrupt Controller Pending Register 3 */
+
+#define IPR(x) __REG(0x40D0001C + (x < 32 ? (x << 2) \
+ : (x < 64 ? (0x94 + ((x - 32) << 2)) \
+ : (0x128 + ((x - 64) << 2)))))
+
#endif /* __ASM_MACH_REGS_INTC_H */
{
if (machine_is_littleton() || machine_is_intelmote2()
|| machine_is_csb726() || machine_is_stargate2()
- || machine_is_cm_x300())
+ || machine_is_cm_x300() || machine_is_balloon3())
UART = STUART;
}
void __init pxa_init_irq(int irq_nr, set_wake_t fn)
{
- int irq;
+ int irq, i;
pxa_internal_irq_nr = irq_nr;
_ICLR(irq) = 0; /* all IRQs are IRQ, not FIQ */
}
+ /* initialize interrupt priority */
+ if (cpu_is_pxa27x() || cpu_is_pxa3xx()) {
+ for (i = 0; i < irq_nr; i++)
+ IPR(i) = i | (1 << 31);
+ }
+
/* only unmasked interrupts kick us out of idle */
ICCR = 1;
#endif
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
-static int littleton_mci_init(struct device *dev,
- irq_handler_t littleton_detect_int, void *data)
-{
- int err, gpio_cd = GPIO_MMC1_CARD_DETECT;
-
- err = gpio_request(gpio_cd, "mmc card detect");
- if (err)
- goto err_request_cd;
-
- gpio_direction_input(gpio_cd);
-
- err = request_irq(gpio_to_irq(gpio_cd), littleton_detect_int,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "mmc card detect", data);
- if (err) {
- dev_err(dev, "failed to request card detect IRQ\n");
- goto err_request_irq;
- }
- return 0;
-
-err_request_irq:
- gpio_free(gpio_cd);
-err_request_cd:
- return err;
-}
-
-static void littleton_mci_exit(struct device *dev, void *data)
-{
- int gpio_cd = GPIO_MMC1_CARD_DETECT;
-
- free_irq(gpio_to_irq(gpio_cd), data);
- gpio_free(gpio_cd);
-}
-
static struct pxamci_platform_data littleton_mci_platform_data = {
- .detect_delay = 20,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = littleton_mci_init,
- .exit = littleton_mci_exit,
+ .detect_delay = 20,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_MMC1_CARD_DETECT,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void __init littleton_init_mmc(void)
}
static struct pxamci_platform_data lubbock_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .detect_delay = 1,
- .init = lubbock_mci_init,
- .get_ro = lubbock_mci_get_ro,
- .exit = lubbock_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .detect_delay = 1,
+ .init = lubbock_mci_init,
+ .get_ro = lubbock_mci_get_ro,
+ .exit = lubbock_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void lubbock_irda_transceiver_mode(struct device *dev, int mode)
}
static struct pxaficp_platform_data lubbock_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE,
- .transceiver_mode = lubbock_irda_transceiver_mode,
+ .gpio_pwdown = -1,
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE,
+ .transceiver_mode = lubbock_irda_transceiver_mode,
};
static void __init lubbock_init(void)
* IRDA
*/
-static void magician_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO83_MAGICIAN_nIR_EN, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data magician_ficp_info = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = magician_irda_transceiver_mode,
+ .gpio_pwdown = GPIO83_MAGICIAN_nIR_EN,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/*
static int magician_mci_init(struct device *dev,
irq_handler_t detect_irq, void *data)
{
- int err;
-
- err = request_irq(IRQ_MAGICIAN_SD, detect_irq,
+ return request_irq(IRQ_MAGICIAN_SD, detect_irq,
IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
- "MMC card detect", data);
- if (err)
- goto err_request_irq;
- err = gpio_request(EGPIO_MAGICIAN_SD_POWER, "SD_POWER");
- if (err)
- goto err_request_power;
- err = gpio_request(EGPIO_MAGICIAN_nSD_READONLY, "nSD_READONLY");
- if (err)
- goto err_request_readonly;
-
- return 0;
-
-err_request_readonly:
- gpio_free(EGPIO_MAGICIAN_SD_POWER);
-err_request_power:
- free_irq(IRQ_MAGICIAN_SD, data);
-err_request_irq:
- return err;
-}
-
-static void magician_mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *pdata = dev->platform_data;
-
- gpio_set_value(EGPIO_MAGICIAN_SD_POWER, (1 << vdd) & pdata->ocr_mask);
-}
-
-static int magician_mci_get_ro(struct device *dev)
-{
- return (!gpio_get_value(EGPIO_MAGICIAN_nSD_READONLY));
+ "mmc card detect", data);
}
static void magician_mci_exit(struct device *dev, void *data)
{
- gpio_free(EGPIO_MAGICIAN_nSD_READONLY);
- gpio_free(EGPIO_MAGICIAN_SD_POWER);
free_irq(IRQ_MAGICIAN_SD, data);
}
static struct pxamci_platform_data magician_mci_info = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = magician_mci_init,
- .get_ro = magician_mci_get_ro,
- .setpower = magician_mci_setpower,
- .exit = magician_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = magician_mci_init,
+ .exit = magician_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = EGPIO_MAGICIAN_nSD_READONLY,
+ .gpio_card_ro_invert = 1,
+ .gpio_power = EGPIO_MAGICIAN_SD_POWER,
};
}
static struct pxamci_platform_data mainstone_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = mainstone_mci_init,
- .setpower = mainstone_mci_setpower,
- .exit = mainstone_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = mainstone_mci_init,
+ .setpower = mainstone_mci_setpower,
+ .exit = mainstone_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static void mainstone_irda_transceiver_mode(struct device *dev, int mode)
}
static struct pxaficp_platform_data mainstone_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = mainstone_irda_transceiver_mode,
+ .gpio_pwdown = -1,
+ .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
+ .transceiver_mode = mainstone_irda_transceiver_mode,
};
static struct gpio_keys_button gpio_keys_button[] = {
/*
* SDIO/MMC Card controller
*/
-static void mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
-
- if ((1 << vdd) & p_d->ocr_mask)
- gpio_set_value(GPIO91_SDIO_EN, 1); /* enable SDIO power */
- else
- gpio_set_value(GPIO91_SDIO_EN, 0); /* disable SDIO power */
-}
-
-static int mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO78_SDIO_RO);
-}
-
-struct gpio_ress mci_gpios[] = {
- MIO_GPIO_IN(GPIO78_SDIO_RO, "SDIO readonly detect"),
- MIO_GPIO_IN(GPIO15_SDIO_INSERT, "SDIO insertion detect"),
- MIO_GPIO_OUT(GPIO91_SDIO_EN, 0, "SDIO power enable")
-};
-
-static void mci_exit(struct device *dev, void *data)
-{
- mio_gpio_free(ARRAY_AND_SIZE(mci_gpios));
- free_irq(gpio_to_irq(GPIO15_SDIO_INSERT), data);
-}
-
-static struct pxamci_platform_data mioa701_mci_info;
-
/**
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-static int mci_init(struct device *dev, irq_handler_t detect_int, void *data)
-{
- int rc;
- int irq = gpio_to_irq(GPIO15_SDIO_INSERT);
-
- rc = mio_gpio_request(ARRAY_AND_SIZE(mci_gpios));
- if (rc)
- goto err_gpio;
- /* enable RE/FE interrupt on card insertion and removal */
- rc = request_irq(irq, detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING |
- IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (rc)
- goto err_irq;
-
- mioa701_mci_info.detect_delay = msecs_to_jiffies(250);
- return 0;
-
-err_irq:
- dev_err(dev, "mioa701_mci_init: MMC/SD:"
- " can't request MMC card detect IRQ\n");
- mio_gpio_free(ARRAY_AND_SIZE(mci_gpios));
-err_gpio:
- return rc;
-}
-
static struct pxamci_platform_data mioa701_mci_info = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = mci_init,
- .get_ro = mci_get_ro,
- .setpower = mci_setpower,
- .exit = mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO15_SDIO_INSERT,
+ .gpio_card_ro = GPIO78_SDIO_RO,
+ .gpio_power = GPIO91_SDIO_EN,
};
/* FlashRAM */
},
};
-static struct soc_camera_link iclink = {
- .bus_id = 0, /* Must match id in pxa27x_device_camera in device.c */
-};
-
/* Board I2C devices. */
static struct i2c_board_info __initdata mioa701_i2c_devices[] = {
{
- /* Must initialize before the camera(s) */
I2C_BOARD_INFO("mt9m111", 0x5d),
- .platform_data = &iclink,
},
};
+static struct soc_camera_link iclink = {
+ .bus_id = 0, /* Match id in pxa27x_device_camera in device.c */
+ .board_info = &mioa701_i2c_devices[0],
+ .i2c_adapter_id = 0,
+ .module_name = "mt9m111",
+};
+
struct i2c_pxa_platform_data i2c_pdata = {
.fast_mode = 1,
};
MIO_SIMPLE_DEV(mioa701_sound, "mioa701-wm9713", NULL)
MIO_SIMPLE_DEV(mioa701_board, "mioa701-board", NULL)
MIO_SIMPLE_DEV(gpio_vbus, "gpio-vbus", &gpio_vbus_data);
+MIO_SIMPLE_DEV(mioa701_camera, "soc-camera-pdrv",&iclink);
static struct platform_device *devices[] __initdata = {
&mioa701_gpio_keys,
&power_dev,
&strataflash,
&gpio_vbus,
+ &mioa701_camera,
&mioa701_board,
};
static struct gpio_ress global_gpios[] = {
MIO_GPIO_OUT(GPIO9_CHARGE_EN, 1, "Charger enable"),
MIO_GPIO_OUT(GPIO18_POWEROFF, 0, "Power Off"),
- MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power")
+ MIO_GPIO_OUT(GPIO87_LCD_POWER, 0, "LCD Power"),
};
static void __init mioa701_machine_init(void)
mio_gpio_request(ARRAY_AND_SIZE(global_gpios));
bootstrap_init();
set_pxa_fb_info(&mioa701_pxafb_info);
+ mioa701_mci_info.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&mioa701_mci_info);
pxa_set_keypad_info(&mioa701_keypad_info);
wm97xx_bat_set_pdata(&mioa701_battery_data);
pxa_set_i2c_info(&i2c_pdata);
pxa27x_set_i2c_power_info(NULL);
pxa_set_camera_info(&mioa701_pxacamera_platform_data);
- i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
}
static void mioa701_machine_exit(void)
#include <linux/wm97xx_batt.h>
#include <linux/power_supply.h>
#include <linux/sysdev.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
};
/******************************************************************************
- * SD/MMC card controller
+ * NOR Flash
******************************************************************************/
-static int palmld_mci_init(struct device *dev, irq_handler_t palmld_detect_int,
- void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMLD_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMLD_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N),
- palmld_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
+static struct mtd_partition palmld_partitions[] = {
+ {
+ .name = "Flash",
+ .offset = 0x00000000,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0
}
+};
- err = gpio_request(GPIO_NR_PALMLD_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMLD_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMLD_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMLD_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMLD_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMLD_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMLD_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmld_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMLD_SD_READONLY);
- gpio_free(GPIO_NR_PALMLD_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_PALMLD_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMLD_SD_DETECT_N);
-}
+static struct physmap_flash_data palmld_flash_data[] = {
+ {
+ .width = 2, /* bankwidth in bytes */
+ .parts = palmld_partitions,
+ .nr_parts = ARRAY_SIZE(palmld_partitions)
+ }
+};
-static void palmld_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMLD_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
+static struct resource palmld_flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_4M - 1,
+ .flags = IORESOURCE_MEM,
+};
-static int palmld_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMLD_SD_READONLY);
-}
+static struct platform_device palmld_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .resource = &palmld_flash_resource,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = palmld_flash_data,
+ },
+};
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
static struct pxamci_platform_data palmld_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmld_mci_power,
- .get_ro = palmld_mci_get_ro,
- .init = palmld_mci_init,
- .exit = palmld_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMLD_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMLD_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMLD_SD_POWER,
+ .detect_delay = 20,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmld_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMLD_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMLD_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMLD_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmld_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMLD_IR_DISABLE);
-}
-
-static void palmld_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMLD_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmld_ficp_platform_data = {
- .startup = palmld_irda_startup,
- .shutdown = palmld_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmld_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMLD_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
&power_supply,
&palmld_asoc,
&palmld_hdd,
+ &palmld_flash,
};
static struct map_desc palmld_io_desc[] __initdata = {
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int palmt5_mci_init(struct device *dev, irq_handler_t palmt5_detect_int,
- void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMT5_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMT5_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMT5_SD_DETECT_N),
- palmt5_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- err = gpio_request(GPIO_NR_PALMT5_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMT5_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMT5_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMT5_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMT5_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMT5_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMT5_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMT5_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmt5_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMT5_SD_READONLY);
- gpio_free(GPIO_NR_PALMT5_SD_POWER);
- free_irq(IRQ_GPIO_PALMT5_SD_DETECT_N, data);
- gpio_free(GPIO_NR_PALMT5_SD_DETECT_N);
-}
-
-static void palmt5_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMT5_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int palmt5_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMT5_SD_READONLY);
-}
-
static struct pxamci_platform_data palmt5_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmt5_mci_power,
- .get_ro = palmt5_mci_get_ro,
- .init = palmt5_mci_init,
- .exit = palmt5_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMT5_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMT5_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMT5_SD_POWER,
+ .detect_delay = 20,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmt5_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMT5_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMT5_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMT5_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmt5_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMT5_IR_DISABLE);
-}
-
-static void palmt5_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMT5_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmt5_ficp_platform_data = {
- .startup = palmt5_irda_startup,
- .shutdown = palmt5_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmt5_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMT5_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
--- /dev/null
+/*
+ * linux/arch/arm/mach-pxa/palmtc.c
+ *
+ * Support for the Palm Tungsten|C
+ *
+ * Author: Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Based on work of:
+ * Petr Blaha <p3t3@centrum.cz>
+ * Chetan S. Kumar <shivakumar.chetan@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/input.h>
+#include <linux/pwm_backlight.h>
+#include <linux/gpio.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/ucb1400.h>
+#include <linux/power_supply.h>
+#include <linux/gpio_keys.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/audio.h>
+#include <mach/palmtc.h>
+#include <mach/mmc.h>
+#include <mach/pxafb.h>
+#include <mach/mfp-pxa25x.h>
+#include <mach/irda.h>
+#include <mach/udc.h>
+#include <mach/pxa2xx-regs.h>
+
+#include "generic.h"
+#include "devices.h"
+
+/******************************************************************************
+ * Pin configuration
+ ******************************************************************************/
+static unsigned long palmtc_pin_config[] __initdata = {
+ /* MMC */
+ GPIO6_MMC_CLK,
+ GPIO8_MMC_CS0,
+ GPIO12_GPIO, /* detect */
+ GPIO32_GPIO, /* power */
+ GPIO54_GPIO, /* r/o switch */
+
+ /* PCMCIA */
+ GPIO52_nPCE_1,
+ GPIO53_nPCE_2,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO49_nPWE,
+ GPIO48_nPOE,
+ GPIO52_nPCE_1,
+ GPIO53_nPCE_2,
+ GPIO57_nIOIS16,
+ GPIO56_nPWAIT,
+
+ /* AC97 */
+ GPIO28_AC97_BITCLK,
+ GPIO29_AC97_SDATA_IN_0,
+ GPIO30_AC97_SDATA_OUT,
+ GPIO31_AC97_SYNC,
+
+ /* IrDA */
+ GPIO45_GPIO, /* ir disable */
+ GPIO46_FICP_RXD,
+ GPIO47_FICP_TXD,
+
+ /* PWM */
+ GPIO17_PWM1_OUT,
+
+ /* USB */
+ GPIO4_GPIO, /* detect */
+ GPIO36_GPIO, /* pullup */
+
+ /* LCD */
+ GPIO58_LCD_LDD_0,
+ GPIO59_LCD_LDD_1,
+ GPIO60_LCD_LDD_2,
+ GPIO61_LCD_LDD_3,
+ GPIO62_LCD_LDD_4,
+ GPIO63_LCD_LDD_5,
+ GPIO64_LCD_LDD_6,
+ GPIO65_LCD_LDD_7,
+ GPIO66_LCD_LDD_8,
+ GPIO67_LCD_LDD_9,
+ GPIO68_LCD_LDD_10,
+ GPIO69_LCD_LDD_11,
+ GPIO70_LCD_LDD_12,
+ GPIO71_LCD_LDD_13,
+ GPIO72_LCD_LDD_14,
+ GPIO73_LCD_LDD_15,
+ GPIO74_LCD_FCLK,
+ GPIO75_LCD_LCLK,
+ GPIO76_LCD_PCLK,
+ GPIO77_LCD_BIAS,
+
+ /* MATRIX KEYPAD */
+ GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 0 */
+ GPIO9_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 1 */
+ GPIO10_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 2 */
+ GPIO11_GPIO | WAKEUP_ON_EDGE_BOTH, /* in 3 */
+ GPIO18_GPIO | MFP_LPM_DRIVE_LOW, /* out 0 */
+ GPIO19_GPIO | MFP_LPM_DRIVE_LOW, /* out 1 */
+ GPIO20_GPIO | MFP_LPM_DRIVE_LOW, /* out 2 */
+ GPIO21_GPIO | MFP_LPM_DRIVE_LOW, /* out 3 */
+ GPIO22_GPIO | MFP_LPM_DRIVE_LOW, /* out 4 */
+ GPIO23_GPIO | MFP_LPM_DRIVE_LOW, /* out 5 */
+ GPIO24_GPIO | MFP_LPM_DRIVE_LOW, /* out 6 */
+ GPIO25_GPIO | MFP_LPM_DRIVE_LOW, /* out 7 */
+ GPIO26_GPIO | MFP_LPM_DRIVE_LOW, /* out 8 */
+ GPIO27_GPIO | MFP_LPM_DRIVE_LOW, /* out 9 */
+ GPIO79_GPIO | MFP_LPM_DRIVE_LOW, /* out 10 */
+ GPIO80_GPIO | MFP_LPM_DRIVE_LOW, /* out 11 */
+
+ /* PXA GPIO KEYS */
+ GPIO7_GPIO | WAKEUP_ON_EDGE_BOTH, /* hotsync button on cradle */
+
+ /* MISC */
+ GPIO1_RST, /* reset */
+ GPIO2_GPIO, /* earphone detect */
+ GPIO16_GPIO, /* backlight switch */
+};
+
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
+static struct pxamci_platform_data palmtc_mci_platform_data = {
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_power = GPIO_NR_PALMTC_SD_POWER,
+ .gpio_card_ro = GPIO_NR_PALMTC_SD_READONLY,
+ .gpio_card_detect = GPIO_NR_PALMTC_SD_DETECT_N,
+ .detect_delay = 20,
+};
+
+/******************************************************************************
+ * GPIO keys
+ ******************************************************************************/
+static struct gpio_keys_button palmtc_pxa_buttons[] = {
+ {KEY_F8, GPIO_NR_PALMTC_HOTSYNC_BUTTON, 1, "HotSync Button", EV_KEY, 1},
+};
+
+static struct gpio_keys_platform_data palmtc_pxa_keys_data = {
+ .buttons = palmtc_pxa_buttons,
+ .nbuttons = ARRAY_SIZE(palmtc_pxa_buttons),
+};
+
+static struct platform_device palmtc_pxa_keys = {
+ .name = "gpio-keys",
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtc_pxa_keys_data,
+ },
+};
+
+/******************************************************************************
+ * Backlight
+ ******************************************************************************/
+static int palmtc_backlight_init(struct device *dev)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_PALMTC_BL_POWER, "BL POWER");
+ if (ret)
+ goto err;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_BL_POWER, 1);
+ if (ret)
+ goto err2;
+
+ return 0;
+
+err2:
+ gpio_free(GPIO_NR_PALMTC_BL_POWER);
+err:
+ return ret;
+}
+
+static int palmtc_backlight_notify(int brightness)
+{
+ /* backlight is on when GPIO16 AF0 is high */
+ gpio_set_value(GPIO_NR_PALMTC_BL_POWER, brightness);
+ return brightness;
+}
+
+static void palmtc_backlight_exit(struct device *dev)
+{
+ gpio_free(GPIO_NR_PALMTC_BL_POWER);
+}
+
+static struct platform_pwm_backlight_data palmtc_backlight_data = {
+ .pwm_id = 1,
+ .max_brightness = PALMTC_MAX_INTENSITY,
+ .dft_brightness = PALMTC_MAX_INTENSITY,
+ .pwm_period_ns = PALMTC_PERIOD_NS,
+ .init = palmtc_backlight_init,
+ .notify = palmtc_backlight_notify,
+ .exit = palmtc_backlight_exit,
+};
+
+static struct platform_device palmtc_backlight = {
+ .name = "pwm-backlight",
+ .dev = {
+ .parent = &pxa25x_device_pwm1.dev,
+ .platform_data = &palmtc_backlight_data,
+ },
+};
+
+/******************************************************************************
+ * IrDA
+ ******************************************************************************/
+static struct pxaficp_platform_data palmtc_ficp_platform_data = {
+ .gpio_pwdown = GPIO_NR_PALMTC_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
+};
+
+/******************************************************************************
+ * Keyboard
+ ******************************************************************************/
+static const uint32_t palmtc_matrix_keys[] = {
+ KEY(0, 0, KEY_F1),
+ KEY(0, 1, KEY_X),
+ KEY(0, 2, KEY_POWER),
+ KEY(0, 3, KEY_TAB),
+ KEY(0, 4, KEY_A),
+ KEY(0, 5, KEY_Q),
+ KEY(0, 6, KEY_LEFTSHIFT),
+ KEY(0, 7, KEY_Z),
+ KEY(0, 8, KEY_S),
+ KEY(0, 9, KEY_W),
+ KEY(0, 10, KEY_E),
+ KEY(0, 11, KEY_UP),
+
+ KEY(1, 0, KEY_F2),
+ KEY(1, 1, KEY_DOWN),
+ KEY(1, 3, KEY_D),
+ KEY(1, 4, KEY_C),
+ KEY(1, 5, KEY_F),
+ KEY(1, 6, KEY_R),
+ KEY(1, 7, KEY_SPACE),
+ KEY(1, 8, KEY_V),
+ KEY(1, 9, KEY_G),
+ KEY(1, 10, KEY_T),
+ KEY(1, 11, KEY_LEFT),
+
+ KEY(2, 0, KEY_F3),
+ KEY(2, 1, KEY_LEFTCTRL),
+ KEY(2, 3, KEY_H),
+ KEY(2, 4, KEY_Y),
+ KEY(2, 5, KEY_N),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_U),
+ KEY(2, 8, KEY_M),
+ KEY(2, 9, KEY_K),
+ KEY(2, 10, KEY_I),
+ KEY(2, 11, KEY_RIGHT),
+
+ KEY(3, 0, KEY_F4),
+ KEY(3, 1, KEY_ENTER),
+ KEY(3, 3, KEY_DOT),
+ KEY(3, 4, KEY_L),
+ KEY(3, 5, KEY_O),
+ KEY(3, 6, KEY_LEFTALT),
+ KEY(3, 7, KEY_ENTER),
+ KEY(3, 8, KEY_BACKSPACE),
+ KEY(3, 9, KEY_P),
+ KEY(3, 10, KEY_B),
+ KEY(3, 11, KEY_FN),
+};
+
+const struct matrix_keymap_data palmtc_keymap_data = {
+ .keymap = palmtc_matrix_keys,
+ .keymap_size = ARRAY_SIZE(palmtc_matrix_keys),
+};
+
+const static unsigned int palmtc_keypad_row_gpios[] = {
+ 0, 9, 10, 11
+};
+
+const static unsigned int palmtc_keypad_col_gpios[] = {
+ 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 79, 80
+};
+
+static struct matrix_keypad_platform_data palmtc_keypad_platform_data = {
+ .keymap_data = &palmtc_keymap_data,
+ .col_gpios = palmtc_keypad_row_gpios,
+ .num_col_gpios = 12,
+ .row_gpios = palmtc_keypad_col_gpios,
+ .num_row_gpios = 4,
+ .active_low = 1,
+
+ .debounce_ms = 20,
+ .col_scan_delay_us = 5,
+};
+
+static struct platform_device palmtc_keyboard = {
+ .name = "matrix-keypad",
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtc_keypad_platform_data,
+ },
+};
+
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct pxa2xx_udc_mach_info palmtc_udc_info __initdata = {
+ .gpio_vbus = GPIO_NR_PALMTC_USB_DETECT_N,
+ .gpio_vbus_inverted = 1,
+ .gpio_pullup = GPIO_NR_PALMTC_USB_POWER,
+};
+
+/******************************************************************************
+ * Touchscreen / Battery / GPIO-extender
+ ******************************************************************************/
+static struct platform_device palmtc_ucb1400_core = {
+ .name = "ucb1400_core",
+ .id = -1,
+};
+
+/******************************************************************************
+ * NOR Flash
+ ******************************************************************************/
+static struct resource palmtc_flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_16M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct mtd_partition palmtc_flash_parts[] = {
+ {
+ .name = "U-Boot Bootloader",
+ .offset = 0x0,
+ .size = 0x40000,
+ },
+ {
+ .name = "Linux Kernel",
+ .offset = 0x40000,
+ .size = 0x2c0000,
+ },
+ {
+ .name = "Filesystem",
+ .offset = 0x300000,
+ .size = 0xcc0000,
+ },
+ {
+ .name = "U-Boot Environment",
+ .offset = 0xfc0000,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct physmap_flash_data palmtc_flash_data = {
+ .width = 4,
+ .parts = palmtc_flash_parts,
+ .nr_parts = ARRAY_SIZE(palmtc_flash_parts),
+};
+
+static struct platform_device palmtc_flash = {
+ .name = "physmap-flash",
+ .id = -1,
+ .resource = &palmtc_flash_resource,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = &palmtc_flash_data,
+ },
+};
+
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+static struct pxafb_mode_info palmtc_lcd_modes[] = {
+{
+ .pixclock = 115384,
+ .xres = 320,
+ .yres = 320,
+ .bpp = 16,
+
+ .left_margin = 27,
+ .right_margin = 7,
+ .upper_margin = 7,
+ .lower_margin = 8,
+
+ .hsync_len = 6,
+ .vsync_len = 1,
+},
+};
+
+static struct pxafb_mach_info palmtc_lcd_screen = {
+ .modes = palmtc_lcd_modes,
+ .num_modes = ARRAY_SIZE(palmtc_lcd_modes),
+ .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+/******************************************************************************
+ * Machine init
+ ******************************************************************************/
+static struct platform_device *devices[] __initdata = {
+ &palmtc_backlight,
+ &palmtc_ucb1400_core,
+ &palmtc_keyboard,
+ &palmtc_pxa_keys,
+ &palmtc_flash,
+};
+
+static void __init palmtc_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtc_pin_config));
+
+ set_pxa_fb_info(&palmtc_lcd_screen);
+ pxa_set_mci_info(&palmtc_mci_platform_data);
+ pxa_set_udc_info(&palmtc_udc_info);
+ pxa_set_ac97_info(NULL);
+ pxa_set_ficp_info(&palmtc_ficp_platform_data);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+};
+
+MACHINE_START(PALMTC, "Palm Tungsten|C")
+ .phys_io = 0x40000000,
+ .boot_params = 0xa0000100,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .map_io = pxa_map_io,
+ .init_irq = pxa25x_init_irq,
+ .timer = &pxa_timer,
+ .init_machine = palmtc_init
+MACHINE_END
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int palmte2_mci_init(struct device *dev,
- irq_handler_t palmte2_detect_int, void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMTE2_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMTE2_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N),
- palmte2_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- err = gpio_request(GPIO_NR_PALMTE2_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMTE2_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMTE2_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMTE2_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMTE2_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMTE2_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMTE2_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmte2_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMTE2_SD_READONLY);
- gpio_free(GPIO_NR_PALMTE2_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_PALMTE2_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMTE2_SD_DETECT_N);
-}
-
-static void palmte2_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMTE2_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int palmte2_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMTE2_SD_READONLY);
-}
-
static struct pxamci_platform_data palmte2_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmte2_mci_power,
- .get_ro = palmte2_mci_get_ro,
- .init = palmte2_mci_init,
- .exit = palmte2_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMTE2_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMTE2_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMTE2_SD_POWER,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmte2_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMTE2_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMTE2_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMTE2_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmte2_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMTE2_IR_DISABLE);
-}
-
-static void palmte2_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMTE2_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmte2_ficp_platform_data = {
- .startup = palmte2_irda_startup,
- .shutdown = palmte2_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmte2_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMTE2_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
#include <linux/wm97xx_batt.h>
#include <linux/power_supply.h>
#include <linux/usb/gpio_vbus.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
GPIO34_FFUART_RXD,
GPIO39_FFUART_TXD,
+ /* NAND */
+ GPIO15_nCS_1,
+ GPIO18_RDY,
+
/* MISC. */
GPIO10_GPIO, /* hotsync button */
GPIO12_GPIO, /* power detect */
};
/******************************************************************************
- * SD/MMC card controller
+ * NOR Flash
******************************************************************************/
-static int palmtx_mci_init(struct device *dev, irq_handler_t palmtx_detect_int,
- void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMTX_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMTX_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N),
- palmtx_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
+static struct mtd_partition palmtx_partitions[] = {
+ {
+ .name = "Flash",
+ .offset = 0x00000000,
+ .size = MTDPART_SIZ_FULL,
+ .mask_flags = 0
}
+};
- err = gpio_request(GPIO_NR_PALMTX_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMTX_SD_POWER, 0);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_PALMTX_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMTX_SD_READONLY);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMTX_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_PALMTX_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMTX_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmtx_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMTX_SD_READONLY);
- gpio_free(GPIO_NR_PALMTX_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_PALMTX_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMTX_SD_DETECT_N);
-}
+static struct physmap_flash_data palmtx_flash_data[] = {
+ {
+ .width = 2, /* bankwidth in bytes */
+ .parts = palmtx_partitions,
+ .nr_parts = ARRAY_SIZE(palmtx_partitions)
+ }
+};
-static void palmtx_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_PALMTX_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
+static struct resource palmtx_flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_8M - 1,
+ .flags = IORESOURCE_MEM,
+};
-static int palmtx_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMTX_SD_READONLY);
-}
+static struct platform_device palmtx_flash = {
+ .name = "physmap-flash",
+ .id = 0,
+ .resource = &palmtx_flash_resource,
+ .num_resources = 1,
+ .dev = {
+ .platform_data = palmtx_flash_data,
+ },
+};
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
static struct pxamci_platform_data palmtx_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmtx_mci_power,
- .get_ro = palmtx_mci_get_ro,
- .init = palmtx_mci_init,
- .exit = palmtx_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMTX_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMTX_SD_READONLY,
+ .gpio_power = GPIO_NR_PALMTX_SD_POWER,
+ .detect_delay = 20,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmtx_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMTX_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMTX_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMTX_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmtx_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMTX_IR_DISABLE);
-}
-
-static void palmtx_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMTX_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmtx_ficp_platform_data = {
- .startup = palmtx_irda_startup,
- .shutdown = palmtx_irda_shutdown,
- .transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
- .transceiver_mode = palmtx_irda_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_PALMTX_IR_DISABLE,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
.lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
};
+/******************************************************************************
+ * NAND Flash
+ ******************************************************************************/
+static void palmtx_nand_cmd_ctl(struct mtd_info *mtd, int cmd,
+ unsigned int ctrl)
+{
+ struct nand_chip *this = mtd->priv;
+ unsigned long nandaddr = (unsigned long)this->IO_ADDR_W;
+
+ if (cmd == NAND_CMD_NONE)
+ return;
+
+ if (ctrl & NAND_CLE)
+ writeb(cmd, PALMTX_NAND_CLE_VIRT);
+ else if (ctrl & NAND_ALE)
+ writeb(cmd, PALMTX_NAND_ALE_VIRT);
+ else
+ writeb(cmd, nandaddr);
+}
+
+static struct mtd_partition palmtx_partition_info[] = {
+ [0] = {
+ .name = "palmtx-0",
+ .offset = 0,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static const char *palmtx_part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data palmtx_nand_platdata = {
+ .chip = {
+ .nr_chips = 1,
+ .chip_offset = 0,
+ .nr_partitions = ARRAY_SIZE(palmtx_partition_info),
+ .partitions = palmtx_partition_info,
+ .chip_delay = 20,
+ .part_probe_types = palmtx_part_probes,
+ },
+ .ctrl = {
+ .cmd_ctrl = palmtx_nand_cmd_ctl,
+ },
+};
+
+static struct resource palmtx_nand_resource[] = {
+ [0] = {
+ .start = PXA_CS1_PHYS,
+ .end = PXA_CS1_PHYS + SZ_1M - 1,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device palmtx_nand = {
+ .name = "gen_nand",
+ .num_resources = ARRAY_SIZE(palmtx_nand_resource),
+ .resource = palmtx_nand_resource,
+ .id = -1,
+ .dev = {
+ .platform_data = &palmtx_nand_platdata,
+ }
+};
+
/******************************************************************************
* Power management - standby
******************************************************************************/
&power_supply,
&palmtx_asoc,
&palmtx_gpio_vbus,
+ &palmtx_flash,
+ &palmtx_nand,
};
static struct map_desc palmtx_io_desc[] __initdata = {
.virtual = PALMTX_PCMCIA_VIRT,
.pfn = __phys_to_pfn(PALMTX_PCMCIA_PHYS),
.length = PALMTX_PCMCIA_SIZE,
- .type = MT_DEVICE
-},
+ .type = MT_DEVICE,
+}, {
+ .virtual = PALMTX_NAND_ALE_VIRT,
+ .pfn = __phys_to_pfn(PALMTX_NAND_ALE_PHYS),
+ .length = SZ_1M,
+ .type = MT_DEVICE,
+}, {
+ .virtual = PALMTX_NAND_CLE_VIRT,
+ .pfn = __phys_to_pfn(PALMTX_NAND_CLE_PHYS),
+ .length = SZ_1M,
+ .type = MT_DEVICE,
+}
};
static void __init palmtx_map_io(void)
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int palmz72_mci_init(struct device *dev,
- irq_handler_t palmz72_detect_int, void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_PALMZ72_SD_DETECT_N, "SD IRQ");
- if (err)
- goto err;
- err = gpio_direction_input(GPIO_NR_PALMZ72_SD_DETECT_N);
- if (err)
- goto err2;
- err = request_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N),
- palmz72_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
- if (err) {
- printk(KERN_ERR "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- /* SD_POWER is not actually power, but it is more like chip
- * select, i.e. it is inverted */
-
- err = gpio_request(GPIO_NR_PALMZ72_SD_POWER_N, "SD_POWER");
- if (err)
- goto err3;
- err = gpio_direction_output(GPIO_NR_PALMZ72_SD_POWER_N, 0);
- if (err)
- goto err4;
- err = gpio_request(GPIO_NR_PALMZ72_SD_RO, "SD_RO");
- if (err)
- goto err4;
- err = gpio_direction_input(GPIO_NR_PALMZ72_SD_RO);
- if (err)
- goto err5;
-
- printk(KERN_DEBUG "%s: irq registered\n", __func__);
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_PALMZ72_SD_RO);
-err4:
- gpio_free(GPIO_NR_PALMZ72_SD_POWER_N);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N);
-err:
- return err;
-}
-
-static void palmz72_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_PALMZ72_SD_POWER_N);
- free_irq(gpio_to_irq(GPIO_NR_PALMZ72_SD_DETECT_N), data);
- gpio_free(GPIO_NR_PALMZ72_SD_DETECT_N);
- gpio_free(GPIO_NR_PALMZ72_SD_RO);
-}
-
-static void palmz72_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- if (p_d->ocr_mask & (1 << vdd))
- gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 0);
- else
- gpio_set_value(GPIO_NR_PALMZ72_SD_POWER_N, 1);
-}
-
-static int palmz72_mci_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_PALMZ72_SD_RO);
-}
-
+/* SD_POWER is not actually power, but it is more like chip
+ * select, i.e. it is inverted */
static struct pxamci_platform_data palmz72_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = palmz72_mci_power,
- .get_ro = palmz72_mci_ro,
- .init = palmz72_mci_init,
- .exit = palmz72_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_PALMZ72_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_PALMZ72_SD_RO,
+ .gpio_power = GPIO_NR_PALMZ72_SD_POWER_N,
+ .gpio_power_invert = 1,
};
/******************************************************************************
/******************************************************************************
* IrDA
******************************************************************************/
-static int palmz72_irda_startup(struct device *dev)
-{
- int err;
- err = gpio_request(GPIO_NR_PALMZ72_IR_DISABLE, "IR DISABLE");
- if (err)
- goto err;
- err = gpio_direction_output(GPIO_NR_PALMZ72_IR_DISABLE, 1);
- if (err)
- gpio_free(GPIO_NR_PALMZ72_IR_DISABLE);
-err:
- return err;
-}
-
-static void palmz72_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_PALMZ72_IR_DISABLE);
-}
-
-static void palmz72_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_PALMZ72_IR_DISABLE, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
static struct pxaficp_platform_data palmz72_ficp_platform_data = {
- .startup = palmz72_irda_startup,
- .shutdown = palmz72_irda_shutdown,
+ .gpio_pwdown = GPIO_NR_PALMZ72_IR_DISABLE,
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = palmz72_irda_transceiver_mode,
};
/******************************************************************************
#define MSECS_PER_JIFFY (1000/HZ)
static struct pxamci_platform_data pcm990_mci_platform_data = {
- .detect_delay = 250 / MSECS_PER_JIFFY,
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .init = pcm990_mci_init,
- .setpower = pcm990_mci_setpower,
- .exit = pcm990_mci_exit,
+ .detect_delay = 250 / MSECS_PER_JIFFY,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .init = pcm990_mci_init,
+ .setpower = pcm990_mci_setpower,
+ .exit = pcm990_mci_exit,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static struct pxaohci_platform_data pcm990_ohci_platform_data = {
gpio_bus_switch = -EINVAL;
}
-static struct soc_camera_link iclink = {
- .bus_id = 0, /* Must match with the camera ID above */
- .query_bus_param = pcm990_camera_query_bus_param,
- .set_bus_param = pcm990_camera_set_bus_param,
- .free_bus = pcm990_camera_free_bus,
-};
-
/* Board I2C devices. */
static struct i2c_board_info __initdata pcm990_i2c_devices[] = {
{
/* Must initialize before the camera(s) */
I2C_BOARD_INFO("pca9536", 0x41),
.platform_data = &pca9536_data,
- }, {
+ },
+};
+
+static struct i2c_board_info pcm990_camera_i2c[] = {
+ {
I2C_BOARD_INFO("mt9v022", 0x48),
- .platform_data = &iclink, /* With extender */
}, {
I2C_BOARD_INFO("mt9m001", 0x5d),
- .platform_data = &iclink, /* With extender */
+ },
+};
+
+static struct soc_camera_link iclink[] = {
+ {
+ .bus_id = 0, /* Must match with the camera ID */
+ .board_info = &pcm990_camera_i2c[0],
+ .i2c_adapter_id = 0,
+ .query_bus_param = pcm990_camera_query_bus_param,
+ .set_bus_param = pcm990_camera_set_bus_param,
+ .free_bus = pcm990_camera_free_bus,
+ .module_name = "mt9v022",
+ }, {
+ .bus_id = 0, /* Must match with the camera ID */
+ .board_info = &pcm990_camera_i2c[1],
+ .i2c_adapter_id = 0,
+ .query_bus_param = pcm990_camera_query_bus_param,
+ .set_bus_param = pcm990_camera_set_bus_param,
+ .free_bus = pcm990_camera_free_bus,
+ .module_name = "mt9m001",
+ },
+};
+
+static struct platform_device pcm990_camera[] = {
+ {
+ .name = "soc-camera-pdrv",
+ .id = 0,
+ .dev = {
+ .platform_data = &iclink[0],
+ },
+ }, {
+ .name = "soc-camera-pdrv",
+ .id = 1,
+ .dev = {
+ .platform_data = &iclink[1],
+ },
},
};
#endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
pxa_set_camera_info(&pcm990_pxacamera_platform_data);
i2c_register_board_info(0, ARRAY_AND_SIZE(pcm990_i2c_devices));
+
+ platform_device_register(&pcm990_camera[0]);
+ platform_device_register(&pcm990_camera[1]);
#endif
printk(KERN_INFO "PCM-990 Evaluation baseboard initialized\n");
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-static struct pxamci_platform_data poodle_mci_platform_data;
-
static int poodle_mci_init(struct device *dev, irq_handler_t poodle_detect_int, void *data)
{
int err;
- err = gpio_request(POODLE_GPIO_nSD_DETECT, "nSD_DETECT");
- if (err)
- goto err_out;
-
- err = gpio_request(POODLE_GPIO_nSD_WP, "nSD_WP");
- if (err)
- goto err_free_1;
-
err = gpio_request(POODLE_GPIO_SD_PWR, "SD_PWR");
if (err)
goto err_free_2;
if (err)
goto err_free_3;
- gpio_direction_input(POODLE_GPIO_nSD_DETECT);
- gpio_direction_input(POODLE_GPIO_nSD_WP);
-
gpio_direction_output(POODLE_GPIO_SD_PWR, 0);
gpio_direction_output(POODLE_GPIO_SD_PWR1, 0);
- poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = request_irq(POODLE_IRQ_GPIO_nSD_DETECT, poodle_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
- __func__);
- goto err_free_4;
- }
-
return 0;
-err_free_4:
- gpio_free(POODLE_GPIO_SD_PWR1);
err_free_3:
gpio_free(POODLE_GPIO_SD_PWR);
err_free_2:
- gpio_free(POODLE_GPIO_nSD_WP);
-err_free_1:
- gpio_free(POODLE_GPIO_nSD_DETECT);
-err_out:
return err;
}
}
}
-static int poodle_mci_get_ro(struct device *dev)
-{
- return !!gpio_get_value(POODLE_GPIO_nSD_WP);
- return GPLR(POODLE_GPIO_nSD_WP) & GPIO_bit(POODLE_GPIO_nSD_WP);
-}
-
-
static void poodle_mci_exit(struct device *dev, void *data)
{
- free_irq(POODLE_IRQ_GPIO_nSD_DETECT, data);
gpio_free(POODLE_GPIO_SD_PWR1);
gpio_free(POODLE_GPIO_SD_PWR);
- gpio_free(POODLE_GPIO_nSD_WP);
- gpio_free(POODLE_GPIO_nSD_DETECT);
}
static struct pxamci_platform_data poodle_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = poodle_mci_init,
- .get_ro = poodle_mci_get_ro,
- .setpower = poodle_mci_setpower,
- .exit = poodle_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = poodle_mci_init,
+ .setpower = poodle_mci_setpower,
+ .exit = poodle_mci_exit,
+ .gpio_card_detect = POODLE_IRQ_GPIO_nSD_DETECT,
+ .gpio_card_ro = POODLE_GPIO_nSD_WP,
+ .gpio_power = -1,
};
/*
* Irda
*/
-static void poodle_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(POODLE_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int poodle_irda_startup(struct device *dev)
-{
- int err;
-
- err = gpio_request(POODLE_GPIO_IR_ON, "IR_ON");
- if (err)
- return err;
-
- gpio_direction_output(POODLE_GPIO_IR_ON, 1);
- return 0;
-}
-
-static void poodle_irda_shutdown(struct device *dev)
-{
- gpio_free(POODLE_GPIO_IR_ON);
-}
-
static struct pxaficp_platform_data poodle_ficp_platform_data = {
+ .gpio_pwdown = POODLE_GPIO_IR_ON,
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = poodle_irda_transceiver_mode,
- .startup = poodle_irda_startup,
- .shutdown = poodle_irda_shutdown,
};
set_pxa_fb_parent(&poodle_locomo_device.dev);
set_pxa_fb_info(&poodle_fb_info);
pxa_set_udc_info(&udc_info);
+ poodle_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&poodle_mci_platform_data);
pxa_set_ficp_info(&poodle_ficp_platform_data);
pxa_set_i2c_info(NULL);
} else
BUG();
}
+EXPORT_SYMBOL_GPL(pxa2xx_transceiver_mode);
};
static DEFINE_PXA3_CKEN(common_nand, NAND, 156000000, 0);
+static DEFINE_PXA3_CKEN(gcu, PXA300_GCU, 0, 0);
static struct clk_lookup common_clkregs[] = {
INIT_CLKREG(&clk_common_nand, "pxa3xx-nand", NULL),
+ INIT_CLKREG(&clk_gcu, "pxa3xx-gcu", NULL),
};
static DEFINE_PXA3_CKEN(pxa310_mmc3, MMC3, 19500000, 0);
};
static DEFINE_PXA3_CKEN(pxa320_nand, NAND, 104000000, 0);
+static DEFINE_PXA3_CKEN(gcu, PXA320_GCU, 0, 0);
static struct clk_lookup pxa320_clkregs[] = {
INIT_CLKREG(&clk_pxa320_nand, "pxa3xx-nand", NULL),
+ INIT_CLKREG(&clk_gcu, "pxa3xx-gcu", NULL),
};
static int __init pxa320_init(void)
MFP_ADDR_END,
};
+static struct mfp_addr_map pxa935_mfp_addr_map[] __initdata = {
+ MFP_ADDR(GPIO159, 0x0524),
+ MFP_ADDR(GPIO163, 0x0534),
+ MFP_ADDR(GPIO167, 0x0544),
+ MFP_ADDR(GPIO168, 0x0548),
+ MFP_ADDR(GPIO169, 0x054c),
+ MFP_ADDR(GPIO170, 0x0550),
+ MFP_ADDR(GPIO171, 0x0554),
+ MFP_ADDR(GPIO172, 0x0558),
+ MFP_ADDR(GPIO173, 0x055c),
+
+ MFP_ADDR_END,
+};
+
static int __init pxa930_init(void)
{
- if (cpu_is_pxa930()) {
+ if (cpu_is_pxa930() || cpu_is_pxa935()) {
mfp_init_base(io_p2v(MFPR_BASE));
mfp_init_addr(pxa930_mfp_addr_map);
}
+ if (cpu_is_pxa935())
+ mfp_init_addr(pxa935_mfp_addr_map);
+
return 0;
}
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
#include <linux/mtd/sharpsl.h>
+#include <linux/input/matrix_keypad.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */
GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */
+ /* GPIO matrix keypad */
+ GPIO88_GPIO, /* column 0 */
+ GPIO23_GPIO, /* column 1 */
+ GPIO24_GPIO, /* column 2 */
+ GPIO25_GPIO, /* column 3 */
+ GPIO26_GPIO, /* column 4 */
+ GPIO27_GPIO, /* column 5 */
+ GPIO52_GPIO, /* column 6 */
+ GPIO103_GPIO, /* column 7 */
+ GPIO107_GPIO, /* column 8 */
+ GPIO108_GPIO, /* column 9 */
+ GPIO114_GPIO, /* column 10 */
+ GPIO12_GPIO, /* row 0 */
+ GPIO17_GPIO, /* row 1 */
+ GPIO91_GPIO, /* row 2 */
+ GPIO34_GPIO, /* row 3 */
+ GPIO36_GPIO, /* row 4 */
+ GPIO38_GPIO, /* row 5 */
+ GPIO39_GPIO, /* row 6 */
+
/* I2C */
GPIO117_I2C_SCL,
GPIO118_I2C_SDA,
/*
* Spitz Keyboard Device
*/
+#define SPITZ_KEY_CALENDAR KEY_F1
+#define SPITZ_KEY_ADDRESS KEY_F2
+#define SPITZ_KEY_FN KEY_F3
+#define SPITZ_KEY_CANCEL KEY_F4
+#define SPITZ_KEY_EXOK KEY_F5
+#define SPITZ_KEY_EXCANCEL KEY_F6
+#define SPITZ_KEY_EXJOGDOWN KEY_F7
+#define SPITZ_KEY_EXJOGUP KEY_F8
+#define SPITZ_KEY_JAP1 KEY_LEFTALT
+#define SPITZ_KEY_JAP2 KEY_RIGHTCTRL
+#define SPITZ_KEY_SYNC KEY_F9
+#define SPITZ_KEY_MAIL KEY_F10
+#define SPITZ_KEY_OK KEY_F11
+#define SPITZ_KEY_MENU KEY_F12
+
+static const uint32_t spitzkbd_keymap[] = {
+ KEY(0, 0, KEY_LEFTCTRL),
+ KEY(0, 1, KEY_1),
+ KEY(0, 2, KEY_3),
+ KEY(0, 3, KEY_5),
+ KEY(0, 4, KEY_6),
+ KEY(0, 5, KEY_7),
+ KEY(0, 6, KEY_9),
+ KEY(0, 7, KEY_0),
+ KEY(0, 8, KEY_BACKSPACE),
+ KEY(0, 9, SPITZ_KEY_EXOK), /* EXOK */
+ KEY(0, 10, SPITZ_KEY_EXCANCEL), /* EXCANCEL */
+ KEY(1, 1, KEY_2),
+ KEY(1, 2, KEY_4),
+ KEY(1, 3, KEY_R),
+ KEY(1, 4, KEY_Y),
+ KEY(1, 5, KEY_8),
+ KEY(1, 6, KEY_I),
+ KEY(1, 7, KEY_O),
+ KEY(1, 8, KEY_P),
+ KEY(1, 9, SPITZ_KEY_EXJOGDOWN), /* EXJOGDOWN */
+ KEY(1, 10, SPITZ_KEY_EXJOGUP), /* EXJOGUP */
+ KEY(2, 0, KEY_TAB),
+ KEY(2, 1, KEY_Q),
+ KEY(2, 2, KEY_E),
+ KEY(2, 3, KEY_T),
+ KEY(2, 4, KEY_G),
+ KEY(2, 5, KEY_U),
+ KEY(2, 6, KEY_J),
+ KEY(2, 7, KEY_K),
+ KEY(3, 0, SPITZ_KEY_ADDRESS), /* ADDRESS */
+ KEY(3, 1, KEY_W),
+ KEY(3, 2, KEY_S),
+ KEY(3, 3, KEY_F),
+ KEY(3, 4, KEY_V),
+ KEY(3, 5, KEY_H),
+ KEY(3, 6, KEY_M),
+ KEY(3, 7, KEY_L),
+ KEY(3, 9, KEY_RIGHTSHIFT),
+ KEY(4, 0, SPITZ_KEY_CALENDAR), /* CALENDAR */
+ KEY(4, 1, KEY_A),
+ KEY(4, 2, KEY_D),
+ KEY(4, 3, KEY_C),
+ KEY(4, 4, KEY_B),
+ KEY(4, 5, KEY_N),
+ KEY(4, 6, KEY_DOT),
+ KEY(4, 8, KEY_ENTER),
+ KEY(4, 9, KEY_LEFTSHIFT),
+ KEY(5, 0, SPITZ_KEY_MAIL), /* MAIL */
+ KEY(5, 1, KEY_Z),
+ KEY(5, 2, KEY_X),
+ KEY(5, 3, KEY_MINUS),
+ KEY(5, 4, KEY_SPACE),
+ KEY(5, 5, KEY_COMMA),
+ KEY(5, 7, KEY_UP),
+ KEY(5, 10, SPITZ_KEY_FN), /* FN */
+ KEY(6, 0, KEY_SYSRQ),
+ KEY(6, 1, SPITZ_KEY_JAP1), /* JAP1 */
+ KEY(6, 2, SPITZ_KEY_JAP2), /* JAP2 */
+ KEY(6, 3, SPITZ_KEY_CANCEL), /* CANCEL */
+ KEY(6, 4, SPITZ_KEY_OK), /* OK */
+ KEY(6, 5, SPITZ_KEY_MENU), /* MENU */
+ KEY(6, 6, KEY_LEFT),
+ KEY(6, 7, KEY_DOWN),
+ KEY(6, 8, KEY_RIGHT),
+};
+
+static const struct matrix_keymap_data spitzkbd_keymap_data = {
+ .keymap = spitzkbd_keymap,
+ .keymap_size = ARRAY_SIZE(spitzkbd_keymap),
+};
+
+static const uint32_t spitzkbd_row_gpios[] =
+ { 12, 17, 91, 34, 36, 38, 39 };
+static const uint32_t spitzkbd_col_gpios[] =
+ { 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
+
+static struct matrix_keypad_platform_data spitzkbd_pdata = {
+ .keymap_data = &spitzkbd_keymap_data,
+ .row_gpios = spitzkbd_row_gpios,
+ .col_gpios = spitzkbd_col_gpios,
+ .num_row_gpios = ARRAY_SIZE(spitzkbd_row_gpios),
+ .num_col_gpios = ARRAY_SIZE(spitzkbd_col_gpios),
+ .col_scan_delay_us = 10,
+ .debounce_ms = 10,
+ .wakeup = 1,
+};
+
static struct platform_device spitzkbd_device = {
- .name = "spitz-keyboard",
+ .name = "matrix-keypad",
.id = -1,
+ .dev = {
+ .platform_data = &spitzkbd_pdata,
+ },
};
.vref_delay_usecs = 100,
.x_plate_ohms = 419,
.y_plate_ohms = 486,
+ .pressure_max = 1024,
.gpio_pendown = SPITZ_GPIO_TP_INT,
.wait_for_sync = spitz_wait_for_hsync,
};
* The card detect interrupt isn't debounced so we delay it by 250ms
* to give the card a chance to fully insert/eject.
*/
-
-static struct pxamci_platform_data spitz_mci_platform_data;
-
-static int spitz_mci_init(struct device *dev, irq_handler_t spitz_detect_int, void *data)
-{
- int err;
-
- err = gpio_request(SPITZ_GPIO_nSD_DETECT, "nSD_DETECT");
- if (err)
- goto err_out;
-
- err = gpio_request(SPITZ_GPIO_nSD_WP, "nSD_WP");
- if (err)
- goto err_free_1;
-
- gpio_direction_input(SPITZ_GPIO_nSD_DETECT);
- gpio_direction_input(SPITZ_GPIO_nSD_WP);
-
- spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = request_irq(SPITZ_IRQ_GPIO_nSD_DETECT, spitz_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING |
- IRQF_TRIGGER_FALLING,
- "MMC card detect", data);
- if (err) {
- pr_err("%s: MMC/SD: can't request MMC card detect IRQ\n",
- __func__);
- goto err_free_2;
- }
- return 0;
-
-err_free_2:
- gpio_free(SPITZ_GPIO_nSD_WP);
-err_free_1:
- gpio_free(SPITZ_GPIO_nSD_DETECT);
-err_out:
- return err;
-}
-
static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
{
struct pxamci_platform_data* p_d = dev->platform_data;
spitz_card_pwr_ctrl(SPITZ_PWR_SD, 0x0000);
}
-static int spitz_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(SPITZ_GPIO_nSD_WP);
-}
-
-static void spitz_mci_exit(struct device *dev, void *data)
-{
- free_irq(SPITZ_IRQ_GPIO_nSD_DETECT, data);
- gpio_free(SPITZ_GPIO_nSD_WP);
- gpio_free(SPITZ_GPIO_nSD_DETECT);
-}
-
static struct pxamci_platform_data spitz_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = spitz_mci_init,
- .get_ro = spitz_mci_get_ro,
- .setpower = spitz_mci_setpower,
- .exit = spitz_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .setpower = spitz_mci_setpower,
+ .gpio_card_detect = SPITZ_GPIO_nSD_DETECT,
+ .gpio_card_ro = SPITZ_GPIO_nSD_WP,
+ .gpio_power = -1,
};
/*
* Irda
*/
-static int spitz_irda_startup(struct device *dev)
-{
- int rc;
-
- rc = gpio_request(SPITZ_GPIO_IR_ON, "IrDA on");
- if (rc)
- goto err;
-
- rc = gpio_direction_output(SPITZ_GPIO_IR_ON, 1);
- if (rc)
- goto err_dir;
-
- return 0;
-
-err_dir:
- gpio_free(SPITZ_GPIO_IR_ON);
-err:
- return rc;
-}
-
-static void spitz_irda_shutdown(struct device *dev)
-{
- gpio_free(SPITZ_GPIO_IR_ON);
-}
-
-static void spitz_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(SPITZ_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-#ifdef CONFIG_MACH_AKITA
-static void akita_irda_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(AKITA_GPIO_IR_ON, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-#endif
static struct pxaficp_platform_data spitz_ficp_platform_data = {
+/* .gpio_pwdown is set in spitz_init() and akita_init() accordingly */
.transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = spitz_irda_transceiver_mode,
- .startup = spitz_irda_startup,
- .shutdown = spitz_irda_shutdown,
};
spitz_init_spi();
platform_add_devices(devices, ARRAY_SIZE(devices));
+ spitz_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&spitz_mci_platform_data);
pxa_set_ohci_info(&spitz_ohci_platform_data);
pxa_set_ficp_info(&spitz_ficp_platform_data);
#if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI)
static void __init spitz_init(void)
{
+ spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
+
platform_scoop_config = &spitz_pcmcia_config;
common_init();
static void __init akita_init(void)
{
- spitz_ficp_platform_data.transceiver_mode = akita_irda_transceiver_mode;
+ spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;
/*
* MMC/SD Device
*/
-static struct pxamci_platform_data tosa_mci_platform_data;
-
static int tosa_mci_init(struct device *dev, irq_handler_t tosa_detect_int, void *data)
{
int err;
- tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250);
-
- err = gpio_request(TOSA_GPIO_nSD_DETECT, "MMC/SD card detect");
- if (err) {
- printk(KERN_ERR "tosa_mci_init: can't request nSD_DETECT gpio\n");
- goto err_gpio_detect;
- }
- err = gpio_direction_input(TOSA_GPIO_nSD_DETECT);
- if (err)
- goto err_gpio_detect_dir;
-
- err = request_irq(TOSA_IRQ_GPIO_nSD_DETECT, tosa_detect_int,
- IRQF_DISABLED | IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "MMC/SD card detect", data);
- if (err) {
- printk(KERN_ERR "tosa_mci_init: MMC/SD: can't request MMC card detect IRQ\n");
- goto err_irq;
- }
-
- err = gpio_request(TOSA_GPIO_SD_WP, "SD Write Protect");
- if (err) {
- printk(KERN_ERR "tosa_mci_init: can't request SD_WP gpio\n");
- goto err_gpio_wp;
- }
- err = gpio_direction_input(TOSA_GPIO_SD_WP);
- if (err)
- goto err_gpio_wp_dir;
-
- err = gpio_request(TOSA_GPIO_PWR_ON, "SD Power");
- if (err) {
- printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n");
- goto err_gpio_pwr;
- }
- err = gpio_direction_output(TOSA_GPIO_PWR_ON, 0);
- if (err)
- goto err_gpio_pwr_dir;
-
err = gpio_request(TOSA_GPIO_nSD_INT, "SD Int");
if (err) {
printk(KERN_ERR "tosa_mci_init: can't request SD_PWR gpio\n");
err_gpio_int_dir:
gpio_free(TOSA_GPIO_nSD_INT);
err_gpio_int:
-err_gpio_pwr_dir:
- gpio_free(TOSA_GPIO_PWR_ON);
-err_gpio_pwr:
-err_gpio_wp_dir:
- gpio_free(TOSA_GPIO_SD_WP);
-err_gpio_wp:
- free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data);
-err_irq:
-err_gpio_detect_dir:
- gpio_free(TOSA_GPIO_nSD_DETECT);
-err_gpio_detect:
return err;
}
-static void tosa_mci_setpower(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data* p_d = dev->platform_data;
-
- if (( 1 << vdd) & p_d->ocr_mask) {
- gpio_set_value(TOSA_GPIO_PWR_ON, 1);
- } else {
- gpio_set_value(TOSA_GPIO_PWR_ON, 0);
- }
-}
-
-static int tosa_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(TOSA_GPIO_SD_WP);
-}
-
static void tosa_mci_exit(struct device *dev, void *data)
{
gpio_free(TOSA_GPIO_nSD_INT);
- gpio_free(TOSA_GPIO_PWR_ON);
- gpio_free(TOSA_GPIO_SD_WP);
- free_irq(TOSA_IRQ_GPIO_nSD_DETECT, data);
- gpio_free(TOSA_GPIO_nSD_DETECT);
}
static struct pxamci_platform_data tosa_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
- .init = tosa_mci_init,
- .get_ro = tosa_mci_get_ro,
- .setpower = tosa_mci_setpower,
- .exit = tosa_mci_exit,
+ .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
+ .init = tosa_mci_init,
+ .exit = tosa_mci_exit,
+ .gpio_card_detect = TOSA_GPIO_nSD_DETECT,
+ .gpio_card_ro = TOSA_GPIO_SD_WP,
+ .gpio_power = TOSA_GPIO_PWR_ON,
};
/*
}
static struct pxaficp_platform_data tosa_ficp_platform_data = {
- .transceiver_cap = IR_SIRMODE | IR_OFF,
- .transceiver_mode = tosa_irda_transceiver_mode,
- .startup = tosa_irda_startup,
- .shutdown = tosa_irda_shutdown,
+ .gpio_pwdown = -1,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
+ .transceiver_mode = tosa_irda_transceiver_mode,
+ .startup = tosa_irda_startup,
+ .shutdown = tosa_irda_shutdown,
};
/*
dummy = gpiochip_reserve(TOSA_SCOOP_JC_GPIO_BASE, 12);
dummy = gpiochip_reserve(TOSA_TC6393XB_GPIO_BASE, 16);
+ tosa_mci_platform_data.detect_delay = msecs_to_jiffies(250);
pxa_set_mci_info(&tosa_mci_platform_data);
pxa_set_udc_info(&udc_info);
pxa_set_ficp_info(&tosa_ficp_platform_data);
/******************************************************************************
* SD/MMC card controller
******************************************************************************/
-static int treo680_mci_init(struct device *dev,
- irq_handler_t treo680_detect_int, void *data)
-{
- int err = 0;
-
- /* Setup an interrupt for detecting card insert/remove events */
- err = gpio_request(GPIO_NR_TREO680_SD_DETECT_N, "SD IRQ");
-
- if (err)
- goto err;
-
- err = gpio_direction_input(GPIO_NR_TREO680_SD_DETECT_N);
- if (err)
- goto err2;
-
- err = request_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N),
- treo680_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- "SD/MMC card detect", data);
-
- if (err) {
- dev_err(dev, "%s: cannot request SD/MMC card detect IRQ\n",
- __func__);
- goto err2;
- }
-
- err = gpio_request(GPIO_NR_TREO680_SD_POWER, "SD_POWER");
- if (err)
- goto err3;
-
- err = gpio_direction_output(GPIO_NR_TREO680_SD_POWER, 1);
- if (err)
- goto err4;
-
- err = gpio_request(GPIO_NR_TREO680_SD_READONLY, "SD_READONLY");
- if (err)
- goto err4;
-
- err = gpio_direction_input(GPIO_NR_TREO680_SD_READONLY);
- if (err)
- goto err5;
-
- return 0;
-
-err5:
- gpio_free(GPIO_NR_TREO680_SD_READONLY);
-err4:
- gpio_free(GPIO_NR_TREO680_SD_POWER);
-err3:
- free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
-err2:
- gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
-err:
- return err;
-}
-
-static void treo680_mci_exit(struct device *dev, void *data)
-{
- gpio_free(GPIO_NR_TREO680_SD_READONLY);
- gpio_free(GPIO_NR_TREO680_SD_POWER);
- free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
- gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
-}
-
-static void treo680_mci_power(struct device *dev, unsigned int vdd)
-{
- struct pxamci_platform_data *p_d = dev->platform_data;
- gpio_set_value(GPIO_NR_TREO680_SD_POWER, p_d->ocr_mask & (1 << vdd));
-}
-
-static int treo680_mci_get_ro(struct device *dev)
-{
- return gpio_get_value(GPIO_NR_TREO680_SD_READONLY);
-}
-
static struct pxamci_platform_data treo680_mci_platform_data = {
- .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
- .setpower = treo680_mci_power,
- .get_ro = treo680_mci_get_ro,
- .init = treo680_mci_init,
- .exit = treo680_mci_exit,
+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
+ .gpio_card_detect = GPIO_NR_TREO680_SD_DETECT_N,
+ .gpio_card_ro = GPIO_NR_TREO680_SD_READONLY,
+ .gpio_power = GPIO_NR_TREO680_SD_POWER,
};
/******************************************************************************
ret = gpio_direction_output(GPIO_NR_TREO680_BL_POWER, 0);
if (ret)
goto err2;
- ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
- if (ret)
- goto err2;
- ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
- if (ret)
- goto err3;
return 0;
-err3:
- gpio_free(GPIO_NR_TREO680_LCD_POWER);
+
err2:
gpio_free(GPIO_NR_TREO680_BL_POWER);
err:
static void treo680_backlight_exit(struct device *dev)
{
gpio_free(GPIO_NR_TREO680_BL_POWER);
- gpio_free(GPIO_NR_TREO680_LCD_POWER);
}
static struct platform_pwm_backlight_data treo680_backlight_data = {
/******************************************************************************
* IrDA
******************************************************************************/
-static void treo680_transceiver_mode(struct device *dev, int mode)
-{
- gpio_set_value(GPIO_NR_TREO680_IR_EN, mode & IR_OFF);
- pxa2xx_transceiver_mode(dev, mode);
-}
-
-static int treo680_irda_startup(struct device *dev)
-{
- int err;
-
- err = gpio_request(GPIO_NR_TREO680_IR_EN, "Ir port disable");
- if (err)
- goto err1;
-
- err = gpio_direction_output(GPIO_NR_TREO680_IR_EN, 1);
- if (err)
- goto err2;
-
- return 0;
-
-err2:
- dev_err(dev, "treo680_irda: cannot change IR gpio direction\n");
- gpio_free(GPIO_NR_TREO680_IR_EN);
-err1:
- dev_err(dev, "treo680_irda: cannot allocate IR gpio\n");
- return err;
-}
-
-static void treo680_irda_shutdown(struct device *dev)
-{
- gpio_free(GPIO_NR_TREO680_IR_EN);
-}
-
static struct pxaficp_platform_data treo680_ficp_info = {
- .transceiver_cap = IR_FIRMODE | IR_SIRMODE | IR_OFF,
- .startup = treo680_irda_startup,
- .shutdown = treo680_irda_shutdown,
- .transceiver_mode = treo680_transceiver_mode,
+ .gpio_pwdown = GPIO_NR_TREO680_IR_EN,
+ .transceiver_cap = IR_SIRMODE | IR_OFF,
};
/******************************************************************************
},
};
+static void treo680_lcd_power(int on, struct fb_var_screeninfo *info)
+{
+ gpio_set_value(GPIO_NR_TREO680_BL_POWER, on);
+}
+
static struct pxafb_mach_info treo680_lcd_screen = {
.modes = treo680_lcd_modes,
.num_modes = ARRAY_SIZE(treo680_lcd_modes),
}
}
+static void __init treo680_lcd_power_init(void)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
+ if (ret) {
+ pr_err("Treo680: LCD power GPIO request failed!\n");
+ return;
+ }
+
+ ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
+ if (ret) {
+ pr_err("Treo680: setting LCD power GPIO direction failed!\n");
+ gpio_free(GPIO_NR_TREO680_LCD_POWER);
+ return;
+ }
+
+ treo680_lcd_screen.pxafb_lcd_power = treo680_lcd_power;
+}
+
static void __init treo680_init(void)
{
treo680_pm_init();
pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
pxa_set_keypad_info(&treo680_keypad_platform_data);
+ treo680_lcd_power_init();
set_pxa_fb_info(&treo680_lcd_screen);
pxa_set_mci_info(&treo680_mci_platform_data);
treo680_udc_init();
.exit = trizeps4_mci_exit,
.get_ro = NULL, /* write-protection not supported */
.setpower = NULL, /* power-switching not supported */
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
/****************************************************************************
}
static struct pxaficp_platform_data trizeps4_ficp_platform_data = {
+ .gpio_pwdown = -1,
.transceiver_cap = IR_SIRMODE | IR_FIRMODE | IR_OFF,
.transceiver_mode = trizeps4_irda_transceiver_mode,
.startup = trizeps4_irda_startup,
--- /dev/null
+/* linux/arch/arm/mach-pxa/xcep.c
+ *
+ * Support for the Iskratel Electronics XCEP platform as used in
+ * the Libera instruments from Instrumentation Technologies.
+ *
+ * Author: Ales Bardorfer <ales@i-tech.si>
+ * Contributions by: Abbott, MG (Michael) <michael.abbott@diamond.ac.uk>
+ * Contributions by: Matej Kenda <matej.kenda@i-tech.si>
+ * Created: June 2006
+ * Copyright: (C) 2006-2009 Instrumentation Technologies
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/smc91x.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/irq.h>
+#include <asm/mach/map.h>
+
+#include <plat/i2c.h>
+
+#include <mach/hardware.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/mfp-pxa25x.h>
+
+#include "generic.h"
+
+#define XCEP_ETH_PHYS (PXA_CS3_PHYS + 0x00000300)
+#define XCEP_ETH_PHYS_END (PXA_CS3_PHYS + 0x000fffff)
+#define XCEP_ETH_ATTR (PXA_CS3_PHYS + 0x02000000)
+#define XCEP_ETH_ATTR_END (PXA_CS3_PHYS + 0x020fffff)
+#define XCEP_ETH_IRQ IRQ_GPIO0
+
+/* XCEP CPLD base */
+#define XCEP_CPLD_BASE 0xf0000000
+
+
+/* Flash partitions. */
+
+static struct mtd_partition xcep_partitions[] = {
+ {
+ .name = "Bootloader",
+ .size = 0x00040000,
+ .offset = 0,
+ .mask_flags = MTD_WRITEABLE
+ }, {
+ .name = "Bootloader ENV",
+ .size = 0x00040000,
+ .offset = 0x00040000,
+ .mask_flags = MTD_WRITEABLE
+ }, {
+ .name = "Kernel",
+ .size = 0x00100000,
+ .offset = 0x00080000,
+ }, {
+ .name = "Rescue fs",
+ .size = 0x00280000,
+ .offset = 0x00180000,
+ }, {
+ .name = "Filesystem",
+ .size = MTDPART_SIZ_FULL,
+ .offset = 0x00400000
+ }
+};
+
+static struct physmap_flash_data xcep_flash_data[] = {
+ {
+ .width = 4, /* bankwidth in bytes */
+ .parts = xcep_partitions,
+ .nr_parts = ARRAY_SIZE(xcep_partitions)
+ }
+};
+
+static struct resource flash_resource = {
+ .start = PXA_CS0_PHYS,
+ .end = PXA_CS0_PHYS + SZ_32M - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = xcep_flash_data,
+ },
+ .resource = &flash_resource,
+ .num_resources = 1,
+};
+
+
+
+/* SMC LAN91C111 network controller. */
+
+static struct resource smc91x_resources[] = {
+ [0] = {
+ .name = "smc91x-regs",
+ .start = XCEP_ETH_PHYS,
+ .end = XCEP_ETH_PHYS_END,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = XCEP_ETH_IRQ,
+ .end = XCEP_ETH_IRQ,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .name = "smc91x-attrib",
+ .start = XCEP_ETH_ATTR,
+ .end = XCEP_ETH_ATTR_END,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct smc91x_platdata xcep_smc91x_info = {
+ .flags = SMC91X_USE_32BIT | SMC91X_NOWAIT | SMC91X_USE_DMA,
+};
+
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+ .dev = {
+ .platform_data = &xcep_smc91x_info,
+ },
+};
+
+
+static struct platform_device *devices[] __initdata = {
+ &flash_device,
+ &smc91x_device,
+};
+
+
+/* We have to state that there are HWMON devices on the I2C bus on XCEP.
+ * Drivers for HWMON verify capabilities of the adapter when loading and
+ * refuse to attach if the adapter doesn't support HWMON class of devices.
+ * See also Documentation/i2c/porting-clients. */
+static struct i2c_pxa_platform_data xcep_i2c_platform_data = {
+ .class = I2C_CLASS_HWMON
+};
+
+
+static mfp_cfg_t xcep_pin_config[] __initdata = {
+ GPIO79_nCS_3, /* SMC 91C111 chip select. */
+ GPIO80_nCS_4, /* CPLD chip select. */
+ /* SSP communication to MSP430 */
+ GPIO23_SSP1_SCLK,
+ GPIO24_SSP1_SFRM,
+ GPIO25_SSP1_TXD,
+ GPIO26_SSP1_RXD,
+ GPIO27_SSP1_EXTCLK
+};
+
+static void __init xcep_init(void)
+{
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(xcep_pin_config));
+
+ /* See Intel XScale Developer's Guide for details */
+ /* Set RDF and RDN to appropriate values (chip select 3 (smc91x)) */
+ MSC1 = (MSC1 & 0xffff) | 0xD5540000;
+ /* Set RDF and RDN to appropriate values (chip select 5 (fpga)) */
+ MSC2 = (MSC2 & 0xffff) | 0x72A00000;
+
+ platform_add_devices(ARRAY_AND_SIZE(devices));
+ pxa_set_i2c_info(&xcep_i2c_platform_data);
+}
+
+MACHINE_START(XCEP, "Iskratel XCEP")
+ .phys_io = 0x40000000,
+ .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
+ .boot_params = 0xa0000100,
+ .init_machine = xcep_init,
+ .map_io = pxa_map_io,
+ .init_irq = pxa25x_init_irq,
+ .timer = &pxa_timer,
+MACHINE_END
+
.init = zylonite_mci_init,
.exit = zylonite_mci_exit,
.get_ro = zylonite_mci_ro,
+ .gpio_card_detect = -1,
+ .gpio_card_ro = -1,
+ .gpio_power = -1,
};
static struct pxamci_platform_data zylonite_mci2_platform_data = {
#include <linux/io.h>
#include <linux/smsc911x.h>
#include <linux/ata_platform.h>
+#include <linux/amba/mmci.h>
#include <asm/clkdev.h>
#include <asm/system.h>
#include <asm/mach/flash.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/hardware/gic.h>
return readl(REALVIEW_SYSMCI) & mask;
}
-struct mmc_platform_data realview_mmc0_plat_data = {
+struct mmci_platform_data realview_mmc0_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 17,
.gpio_cd = 16,
};
-struct mmc_platform_data realview_mmc1_plat_data = {
+struct mmci_platform_data realview_mmc1_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 19,
static struct clk_lookup lookups[] = {
{ /* UART0 */
- .dev_id = "dev:f1",
+ .dev_id = "dev:uart0",
.clk = &ref24_clk,
}, { /* UART1 */
- .dev_id = "dev:f2",
+ .dev_id = "dev:uart1",
.clk = &ref24_clk,
}, { /* UART2 */
- .dev_id = "dev:f3",
+ .dev_id = "dev:uart2",
.clk = &ref24_clk,
}, { /* UART3 */
- .dev_id = "fpga:09",
+ .dev_id = "fpga:uart3",
.clk = &ref24_clk,
}, { /* KMI0 */
- .dev_id = "fpga:06",
+ .dev_id = "fpga:kmi0",
.clk = &ref24_clk,
}, { /* KMI1 */
- .dev_id = "fpga:07",
+ .dev_id = "fpga:kmi1",
.clk = &ref24_clk,
}, { /* MMC0 */
- .dev_id = "fpga:05",
+ .dev_id = "fpga:mmc0",
.clk = &ref24_clk,
}, { /* EB:CLCD */
- .dev_id = "dev:20",
+ .dev_id = "dev:clcd",
.clk = &oscvco_clk,
}, { /* PB:CLCD */
- .dev_id = "issp:20",
+ .dev_id = "issp:clcd",
.clk = &oscvco_clk,
}
};
extern struct platform_device realview_flash_device;
extern struct platform_device realview_cf_device;
extern struct platform_device realview_i2c_device;
-extern struct mmc_platform_data realview_mmc0_plat_data;
-extern struct mmc_platform_data realview_mmc1_plat_data;
+extern struct mmci_platform_data realview_mmc0_plat_data;
+extern struct mmci_platform_data realview_mmc1_plat_data;
extern struct clcd_board clcd_plat_data;
extern void __iomem *gic_cpu_base_addr;
extern void __iomem *timer0_va_base;
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/board-eb.h>
#define EB_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", EB_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", EB_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", EB_SMC, NULL);
-AMBA_DEVICE(clcd, "dev:20", EB_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "dev:30", DMAC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", EB_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", EB_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", EB_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", EB_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", EB_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", EB_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", EB_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", EB_SMC, NULL);
+AMBA_DEVICE(clcd, "dev:clcd", EB_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "dev:dmac", DMAC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", EB_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", EB_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", EB_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", EB_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", EB_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", EB_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", EB_SSP, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/board-pb1176.h>
#define PB1176_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PB1176_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PB1176_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PB1176_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PB1176_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PB1176_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PB1176_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PB1176_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PB1176_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PB1176_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PB1176_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PB1176_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PB1176_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PB1176_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PB1176_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PB1176_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PB1176_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PB1176_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PB1176_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PB1176_CLCD, &clcd_plat_data);
-//AMBA_DEVICE(dmac, "issp:30", PB1176_DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PB1176_CLCD, &clcd_plat_data);
+//AMBA_DEVICE(dmac, "issp:dmac", PB1176_DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
// &dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/board-pb11mp.h>
#define PB11MP_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PB11MP_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PB11MP_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PB11MP_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PB11MP_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PB11MP_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PB11MP_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PB11MP_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PB11MP_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PB11MP_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PB11MP_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PB11MP_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PB11MP_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PB11MP_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PB11MP_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PB11MP_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PB11MP_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PB11MP_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PB11MP_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PB11MP_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:30", DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PB11MP_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/hardware.h>
#define PBA8_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PBA8_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PBA8_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PBA8_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PBA8_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PBA8_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PBA8_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PBA8_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PBA8_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PBA8_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PBA8_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PBA8_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PBA8_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PBA8_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PBA8_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PBA8_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PBA8_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PBA8_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PBA8_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PBA8_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:30", DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PBA8_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include <asm/mach/time.h>
#include <mach/hardware.h>
#define PBX_SSP_DMA { 9, 8 }
/* FPGA Primecells */
-AMBA_DEVICE(aaci, "fpga:04", AACI, NULL);
-AMBA_DEVICE(mmc0, "fpga:05", MMCI0, &realview_mmc0_plat_data);
-AMBA_DEVICE(kmi0, "fpga:06", KMI0, NULL);
-AMBA_DEVICE(kmi1, "fpga:07", KMI1, NULL);
-AMBA_DEVICE(uart3, "fpga:09", PBX_UART3, NULL);
+AMBA_DEVICE(aaci, "fpga:aaci", AACI, NULL);
+AMBA_DEVICE(mmc0, "fpga:mmc0", MMCI0, &realview_mmc0_plat_data);
+AMBA_DEVICE(kmi0, "fpga:kmi0", KMI0, NULL);
+AMBA_DEVICE(kmi1, "fpga:kmi1", KMI1, NULL);
+AMBA_DEVICE(uart3, "fpga:uart3", PBX_UART3, NULL);
/* DevChip Primecells */
-AMBA_DEVICE(smc, "dev:00", PBX_SMC, NULL);
-AMBA_DEVICE(sctl, "dev:e0", SCTL, NULL);
-AMBA_DEVICE(wdog, "dev:e1", PBX_WATCHDOG, NULL);
-AMBA_DEVICE(gpio0, "dev:e4", PBX_GPIO0, &gpio0_plat_data);
-AMBA_DEVICE(gpio1, "dev:e5", GPIO1, &gpio1_plat_data);
-AMBA_DEVICE(gpio2, "dev:e6", GPIO2, &gpio2_plat_data);
-AMBA_DEVICE(rtc, "dev:e8", PBX_RTC, NULL);
-AMBA_DEVICE(sci0, "dev:f0", SCI, NULL);
-AMBA_DEVICE(uart0, "dev:f1", PBX_UART0, NULL);
-AMBA_DEVICE(uart1, "dev:f2", PBX_UART1, NULL);
-AMBA_DEVICE(uart2, "dev:f3", PBX_UART2, NULL);
-AMBA_DEVICE(ssp0, "dev:f4", PBX_SSP, NULL);
+AMBA_DEVICE(smc, "dev:smc", PBX_SMC, NULL);
+AMBA_DEVICE(sctl, "dev:sctl", SCTL, NULL);
+AMBA_DEVICE(wdog, "dev:wdog", PBX_WATCHDOG, NULL);
+AMBA_DEVICE(gpio0, "dev:gpio0", PBX_GPIO0, &gpio0_plat_data);
+AMBA_DEVICE(gpio1, "dev:gpio1", GPIO1, &gpio1_plat_data);
+AMBA_DEVICE(gpio2, "dev:gpio2", GPIO2, &gpio2_plat_data);
+AMBA_DEVICE(rtc, "dev:rtc", PBX_RTC, NULL);
+AMBA_DEVICE(sci0, "dev:sci0", SCI, NULL);
+AMBA_DEVICE(uart0, "dev:uart0", PBX_UART0, NULL);
+AMBA_DEVICE(uart1, "dev:uart1", PBX_UART1, NULL);
+AMBA_DEVICE(uart2, "dev:uart2", PBX_UART2, NULL);
+AMBA_DEVICE(ssp0, "dev:ssp0", PBX_SSP, NULL);
/* Primecells on the NEC ISSP chip */
-AMBA_DEVICE(clcd, "issp:20", PBX_CLCD, &clcd_plat_data);
-AMBA_DEVICE(dmac, "issp:30", DMAC, NULL);
+AMBA_DEVICE(clcd, "issp:clcd", PBX_CLCD, &clcd_plat_data);
+AMBA_DEVICE(dmac, "issp:dmac", DMAC, NULL);
static struct amba_device *amba_devs[] __initdata = {
&dmac_device,
select CPU_S3C2410
select PM_H1940 if PM
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the HP IPAQ H1940
bool "Acer N30 family"
select CPU_S3C2410
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you want suppt for the Acer N30, Acer N35,
Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs.
select S3C24XX_DCLK
select ISA
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Simtec Electronics EB2410ITX
development board (also known as BAST)
bool "NexVision OTOM Board"
select CPU_S3C2410
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Nex Vision OTOM board
bool "QT2410"
select CPU_S3C2410
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Armzone QT2410
bool "Logitech Jive"
select CPU_S3C2412
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Logitech Jive.
select MACH_S3C2413
select MACH_SMDK
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using an SMDK2413
bool "VMSTMS"
select CPU_S3C2412
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using an VSTMS board
select S3C2440_XTAL_12000000
select S3C2410_IOTIMING if S3C2440_CPUFREQ
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Simtec IM2440D20 module, also
known as the Osiris.
select CPU_S3C2440
select S3C2440_XTAL_16934400
select PM_H1940 if PM
+ select S3C_DEV_NAND
help
Say Y here if you are using the HP iPAQ rx3715.
select S3C2440_XTAL_16934400
select MACH_SMDK
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the SMDK2440.
select CPU_S3C2440
select S3C2440_XTAL_12000000
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
bool "Avantech AT2440EVB development board"
select CPU_S3C2440
select S3C_DEV_USB_HOST
+ select S3C_DEV_NAND
help
Say Y here if you are using the AT2440EVB development board
select EEPROM_AT24
select LEDS_TRIGGER_BACKLIGHT
select SND_S3C24XX_SOC_S3C24XX_UDA134X
+ select S3C_DEV_NAND
help
Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
available via various sources. It can come with a 3.5" or 7" touch LCD.
bool "SMDK6400"
select CPU_S3C6400
select S3C_DEV_HSMMC
+ select S3C_DEV_NAND
select S3C6400_SETUP_SDHCI
help
Machine support for the Samsung SMDK6400
bool "Airgoo HMT"
select CPU_S3C6410
select S3C_DEV_FB
+ select S3C_DEV_NAND
select S3C_DEV_USB_HOST
select S3C64XX_SETUP_FB_24BPP
select HAVE_PWM
<http://www.handhelds.org/Compaq/index.html#iPAQ_H3600>
<http://www.compaq.com/products/handhelds/pocketpc/>
-config SA1100_H3XXX
- bool
- depends on SA1100_H3100 || SA1100_H3600
- default y
-
config SA1100_BADGE4
bool "HP Labs BadgePAD 4"
select SA1111
static sa1100_dma_t dma_chan[SA1100_DMA_CHANNELS];
-static spinlock_t dma_list_lock;
+static DEFINE_SPINLOCK(dma_list_lock);
static irqreturn_t dma_irq_handler(int irq, void *dev_id)
.set_mode = sa1100_osmr0_set_mode,
};
-static cycle_t sa1100_read_oscr(void)
+static cycle_t sa1100_read_oscr(struct clocksource *s)
{
return OSCR;
}
Memory Interface) from both from access and application
side.
+config MACH_U300_SPIDUMMY
+ bool "SSP/SPI dummy chip"
+ select SPI
+ select SPI_MASTER
+ select SPI_PL022
+ help
+ This creates a small kernel module that creates a dummy
+ SPI device to be used for loopback tests. Regularly used
+ to test reference designs. If you're not testing SPI,
+ you don't need it. Selecting this will activate the
+ SPI framework and ARM PL022 support.
+
comment "All the settings below must match the bootloader's settings"
config MACH_U300_ACCESS_MEM_SIZE
obj-$(CONFIG_ARCH_U300) += u300.o
obj-$(CONFIG_MMC) += mmc.o
+obj-$(CONFIG_SPI_PL022) += spi.o
+obj-$(CONFIG_MACH_U300_SPIDUMMY) += dummyspichip.o
+obj-$(CONFIG_I2C_STU300) += i2c.o
#include "clock.h"
#include "mmc.h"
+#include "spi.h"
+#include "i2c.h"
/*
* Static I/O mappings that are needed for booting the U300 platforms. The
};
static struct platform_device i2c0_device = {
- .name = "stddci2c",
+ .name = "stu300",
.id = 0,
.num_resources = ARRAY_SIZE(i2c0_resources),
.resource = i2c0_resources,
};
static struct platform_device i2c1_device = {
- .name = "stddci2c",
+ .name = "stu300",
.id = 1,
.num_resources = ARRAY_SIZE(i2c1_resources),
.resource = i2c1_resources,
/* Wait for the PLL208 to lock if not locked in yet */
while (!(readw(U300_SYSCON_VBASE + U300_SYSCON_CSR) &
U300_SYSCON_CSR_PLL208_LOCK_IND));
+ /* Initialize SPI device with some board specifics */
+ u300_spi_init(&pl022_device);
/* Register the AMBA devices in the AMBA bus abstraction layer */
u300_clock_primecells();
u300_assign_physmem();
+ /* Register subdevices on the I2C buses */
+ u300_i2c_register_board_devices();
+
+ /* Register subdevices on the SPI bus */
+ u300_spi_register_board_devices();
+
/* Register the platform devices */
platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs));
--- /dev/null
+/*
+ * arch/arm/mach-u300/dummyspichip.c
+ *
+ * Copyright (C) 2007-2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * This is a dummy loopback SPI "chip" used for testing SPI.
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/sysfs.h>
+#include <linux/mutex.h>
+#include <linux/spi/spi.h>
+#include <linux/dma-mapping.h>
+/*
+ * WARNING! Do not include this pl022-specific controller header
+ * for any generic driver. It is only done in this dummy chip
+ * because we alter the chip configuration in order to test some
+ * different settings on the loopback device. Normal chip configs
+ * shall be STATIC and not altered by the driver!
+ */
+#include <linux/amba/pl022.h>
+
+struct dummy {
+ struct device *dev;
+ struct mutex lock;
+};
+
+#define DMA_TEST_SIZE 2048
+
+/* When we cat /sys/bus/spi/devices/spi0.0/looptest this will be triggered */
+static ssize_t dummy_looptest(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct dummy *p_dummy = dev_get_drvdata(&spi->dev);
+
+ /*
+ * WARNING! Do not dereference the chip-specific data in any normal
+ * driver for a chip. It is usually STATIC and shall not be read
+ * or written to. Your chip driver should NOT depend on fields in this
+ * struct, this is just used here to alter the behaviour of the chip
+ * in order to perform tests.
+ */
+ struct pl022_config_chip *chip_info = spi->controller_data;
+ int status;
+ u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
+ 0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
+ 0xF0, 0x0D};
+ u8 rxbuf[14];
+ u8 *bigtxbuf_virtual;
+ u8 *bigrxbuf_virtual;
+
+ if (mutex_lock_interruptible(&p_dummy->lock))
+ return -ERESTARTSYS;
+
+ bigtxbuf_virtual = kmalloc(DMA_TEST_SIZE, GFP_KERNEL);
+ if (bigtxbuf_virtual == NULL) {
+ status = -ENOMEM;
+ goto out;
+ }
+ bigrxbuf_virtual = kmalloc(DMA_TEST_SIZE, GFP_KERNEL);
+
+ /* Fill TXBUF with some happy pattern */
+ memset(bigtxbuf_virtual, 0xAA, DMA_TEST_SIZE);
+
+ /*
+ * Force chip to 8 bit mode
+ * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
+ */
+ chip_info->data_size = SSP_DATA_BITS_8;
+ /* You should NOT DO THIS EITHER */
+ spi->master->setup(spi);
+
+ /* Now run the tests for 8bit mode */
+ pr_info("Simple test 1: write 0xAA byte, read back garbage byte "
+ "in 8bit mode\n");
+ status = spi_w8r8(spi, 0xAA);
+ if (status < 0)
+ pr_warning("Siple test 1: FAILURE: spi_write_then_read "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 1: SUCCESS!\n");
+
+ pr_info("Simple test 2: write 8 bytes, read back 8 bytes garbage "
+ "in 8bit mode (full FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 8, &rxbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 2: FAILURE: spi_write_then_read() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 2: SUCCESS!\n");
+
+ pr_info("Simple test 3: write 14 bytes, read back 14 bytes garbage "
+ "in 8bit mode (see if we overflow FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 14, &rxbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 3: FAILURE: failed with status %d "
+ "(probably FIFO overrun)\n", status);
+ else
+ pr_info("Simple test 3: SUCCESS!\n");
+
+ pr_info("Simple test 4: write 8 bytes with spi_write(), read 8 "
+ "bytes garbage with spi_read() in 8bit mode\n");
+ status = spi_write(spi, &txbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 4 step 1: FAILURE: spi_write() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 4 step 1: SUCCESS!\n");
+ status = spi_read(spi, &rxbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 4 step 2: FAILURE: spi_read() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 4 step 2: SUCCESS!\n");
+
+ pr_info("Simple test 5: write 14 bytes with spi_write(), read "
+ "14 bytes garbage with spi_read() in 8bit mode\n");
+ status = spi_write(spi, &txbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 5 step 1: FAILURE: spi_write() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 5 step 1: SUCCESS!\n");
+ status = spi_read(spi, &rxbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 5 step 2: FAILURE: spi_read() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 5: SUCCESS!\n");
+
+ pr_info("Simple test 6: write %d bytes with spi_write(), "
+ "read %d bytes garbage with spi_read() in 8bit mode\n",
+ DMA_TEST_SIZE, DMA_TEST_SIZE);
+ status = spi_write(spi, &bigtxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 6 step 1: FAILURE: spi_write() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 6 step 1: SUCCESS!\n");
+ status = spi_read(spi, &bigrxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 6 step 2: FAILURE: spi_read() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 6: SUCCESS!\n");
+
+
+ /*
+ * Force chip to 16 bit mode
+ * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
+ */
+ chip_info->data_size = SSP_DATA_BITS_16;
+ /* You should NOT DO THIS EITHER */
+ spi->master->setup(spi);
+
+ pr_info("Simple test 7: write 0xAA byte, read back garbage byte "
+ "in 16bit bus mode\n");
+ status = spi_w8r8(spi, 0xAA);
+ if (status == -EIO)
+ pr_info("Simple test 7: SUCCESS! (expected failure with "
+ "status EIO)\n");
+ else if (status < 0)
+ pr_warning("Siple test 7: FAILURE: spi_write_then_read "
+ "failed with status %d\n", status);
+ else
+ pr_warning("Siple test 7: FAILURE: spi_write_then_read "
+ "succeeded but it was expected to fail!\n");
+
+ pr_info("Simple test 8: write 8 bytes, read back 8 bytes garbage "
+ "in 16bit mode (full FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 8, &rxbuf[0], 8);
+ if (status < 0)
+ pr_warning("Simple test 8: FAILURE: spi_write_then_read() "
+ "failed with status %d\n", status);
+ else
+ pr_info("Simple test 8: SUCCESS!\n");
+
+ pr_info("Simple test 9: write 14 bytes, read back 14 bytes garbage "
+ "in 16bit mode (see if we overflow FIFO)\n");
+ status = spi_write_then_read(spi, &txbuf[0], 14, &rxbuf[0], 14);
+ if (status < 0)
+ pr_warning("Simple test 9: FAILURE: failed with status %d "
+ "(probably FIFO overrun)\n", status);
+ else
+ pr_info("Simple test 9: SUCCESS!\n");
+
+ pr_info("Simple test 10: write %d bytes with spi_write(), "
+ "read %d bytes garbage with spi_read() in 16bit mode\n",
+ DMA_TEST_SIZE, DMA_TEST_SIZE);
+ status = spi_write(spi, &bigtxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 10 step 1: FAILURE: spi_write() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 10 step 1: SUCCESS!\n");
+
+ status = spi_read(spi, &bigrxbuf_virtual[0], DMA_TEST_SIZE);
+ if (status < 0)
+ pr_warning("Simple test 10 step 2: FAILURE: spi_read() "
+ "failed with status %d (probably FIFO overrun)\n",
+ status);
+ else
+ pr_info("Simple test 10: SUCCESS!\n");
+
+ status = sprintf(buf, "loop test complete\n");
+ kfree(bigrxbuf_virtual);
+ kfree(bigtxbuf_virtual);
+ out:
+ mutex_unlock(&p_dummy->lock);
+ return status;
+}
+
+static DEVICE_ATTR(looptest, S_IRUGO, dummy_looptest, NULL);
+
+static int __devinit pl022_dummy_probe(struct spi_device *spi)
+{
+ struct dummy *p_dummy;
+ int status;
+
+ dev_info(&spi->dev, "probing dummy SPI device\n");
+
+ p_dummy = kzalloc(sizeof *p_dummy, GFP_KERNEL);
+ if (!p_dummy)
+ return -ENOMEM;
+
+ dev_set_drvdata(&spi->dev, p_dummy);
+ mutex_init(&p_dummy->lock);
+
+ /* sysfs hook */
+ status = device_create_file(&spi->dev, &dev_attr_looptest);
+ if (status) {
+ dev_dbg(&spi->dev, "device_create_file looptest failure.\n");
+ goto out_dev_create_looptest_failed;
+ }
+
+ return 0;
+
+out_dev_create_looptest_failed:
+ dev_set_drvdata(&spi->dev, NULL);
+ kfree(p_dummy);
+ return status;
+}
+
+static int __devexit pl022_dummy_remove(struct spi_device *spi)
+{
+ struct dummy *p_dummy = dev_get_drvdata(&spi->dev);
+
+ dev_info(&spi->dev, "removing dummy SPI device\n");
+ device_remove_file(&spi->dev, &dev_attr_looptest);
+ dev_set_drvdata(&spi->dev, NULL);
+ kfree(p_dummy);
+
+ return 0;
+}
+
+static struct spi_driver pl022_dummy_driver = {
+ .driver = {
+ .name = "spi-dummy",
+ .owner = THIS_MODULE,
+ },
+ .probe = pl022_dummy_probe,
+ .remove = __devexit_p(pl022_dummy_remove),
+};
+
+static int __init pl022_init_dummy(void)
+{
+ return spi_register_driver(&pl022_dummy_driver);
+}
+
+static void __exit pl022_exit_dummy(void)
+{
+ spi_unregister_driver(&pl022_dummy_driver);
+}
+
+module_init(pl022_init_dummy);
+module_exit(pl022_exit_dummy);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
+MODULE_DESCRIPTION("PL022 SSP/SPI DUMMY Linux driver");
+MODULE_LICENSE("GPL");
#include <linux/platform_device.h>
#include <linux/gpio.h>
-/* Need access to SYSCON registers for PADmuxing */
-#include <mach/syscon.h>
-
-#include "padmux.h"
-
/* Reference to GPIO block clock */
static struct clk *clk;
}
EXPORT_SYMBOL(gpio_unregister_callback);
+/* Non-zero means valid */
+int gpio_is_valid(int number)
+{
+ if (number >= 0 &&
+ number < (U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT))
+ return 1;
+ return 0;
+}
+EXPORT_SYMBOL(gpio_is_valid);
+
int gpio_request(unsigned gpio, const char *label)
{
if (gpio_pin[gpio].users)
writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE, virtbase + U300_GPIO_CR);
#endif
- /* Set up some padmuxing here */
-#ifdef CONFIG_MMC
- pmx_set_mission_mode_mmc();
-#endif
-#ifdef CONFIG_SPI_PL022
- pmx_set_mission_mode_spi();
-#endif
-
gpio_set_initial_values();
for (num_irqs = 0 ; num_irqs < U300_GPIO_NUM_PORTS; num_irqs++) {
--- /dev/null
+/*
+ * arch/arm/mach-u300/i2c.c
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Register board i2c devices
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <mach/irqs.h>
+
+static struct i2c_board_info __initdata bus0_i2c_board_info[] = {
+ {
+ .type = "ab3100",
+ .addr = 0x48,
+ .irq = IRQ_U300_IRQ0_EXT,
+ },
+};
+
+static struct i2c_board_info __initdata bus1_i2c_board_info[] = {
+#ifdef CONFIG_MACH_U300_BS335
+ {
+ .type = "fwcam",
+ .addr = 0x10,
+ },
+ {
+ .type = "fwcam",
+ .addr = 0x5d,
+ },
+#else
+ { },
+#endif
+};
+
+void __init u300_i2c_register_board_devices(void)
+{
+ i2c_register_board_info(0, bus0_i2c_board_info,
+ ARRAY_SIZE(bus0_i2c_board_info));
+ i2c_register_board_info(1, bus1_i2c_board_info,
+ ARRAY_SIZE(bus1_i2c_board_info));
+}
--- /dev/null
+/*
+ * arch/arm/mach-u300/i2c.h
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Register board i2c devices
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+
+#ifndef MACH_U300_I2C_H
+#define MACH_U300_I2C_H
+
+#ifdef CONFIG_I2C_STU300
+void __init u300_i2c_register_board_devices(void);
+#else
+/* Compile out this stuff if no I2C adapter is available */
+static inline void __init u300_i2c_register_board_devices(void)
+{
+}
+#endif
+
+#endif
#define PIN_TO_PORT(val) (val >> 3)
/* These can be found in arch/arm/mach-u300/gpio.c */
+extern int gpio_is_valid(int number);
extern int gpio_request(unsigned gpio, const char *label);
extern void gpio_free(unsigned gpio);
extern int gpio_direction_input(unsigned gpio);
(CONFIG_MACH_U300_ACCESS_MEM_SIZE & 1))*1024*1024 + 0x100)
#endif
+/*
+ * TCM memory whereabouts
+ */
+#define ITCM_OFFSET 0xffff2000
+#define ITCM_END 0xffff3fff
+#define DTCM_OFFSET 0xffff4000
+#define DTCM_END 0xffff5fff
+
/*
* We enable a real big DMA buffer if need be.
*/
#define U300_SYSCON_PMC1LR_CDI_MASK (0xC000)
#define U300_SYSCON_PMC1LR_CDI_CDI (0x0000)
#define U300_SYSCON_PMC1LR_CDI_EMIF (0x4000)
+#ifdef CONFIG_MACH_U300_BS335
+#define U300_SYSCON_PMC1LR_CDI_CDI2 (0x8000)
+#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO (0xC000)
+#elif CONFIG_MACH_U300_BS365
#define U300_SYSCON_PMC1LR_CDI_GPIO (0x8000)
#define U300_SYSCON_PMC1LR_CDI_WCDMA (0xC000)
+#endif
#define U300_SYSCON_PMC1LR_PDI_MASK (0x3000)
#define U300_SYSCON_PMC1LR_PDI_PDI (0x0000)
#define U300_SYSCON_PMC1LR_PDI_EGG (0x1000)
#define U300_SYSCON_MMCR_MASK (0x0003)
#define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE (0x0002)
#define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE (0x0001)
-
+/* Pull up/down control (R/W) */
+#define U300_SYSCON_PUCR (0x104)
+#define U300_SYSCON_PUCR_EMIF_1_WAIT_N_PU_ENABLE (0x0200)
+#define U300_SYSCON_PUCR_EMIF_1_NFIF_READY_PU_ENABLE (0x0100)
+#define U300_SYSCON_PUCR_EMIF_1_16BIT_PU_ENABLE (0x0080)
+#define U300_SYSCON_PUCR_EMIF_1_8BIT_PU_ENABLE (0x0040)
+#define U300_SYSCON_PUCR_KEY_IN_PU_EN_MASK (0x003F)
+/* Padmux 2 control */
+#define U300_SYSCON_PMC2R (0x100)
+#define U300_SYSCON_PMC2R_APP_MISC_0_MASK (0x00C0)
+#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM (0x0040)
+#define U300_SYSCON_PMC2R_APP_MISC_0_MMC (0x0080)
+#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 (0x00C0)
+#define U300_SYSCON_PMC2R_APP_MISC_1_MASK (0x0300)
+#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM (0x0100)
+#define U300_SYSCON_PMC2R_APP_MISC_1_MMC (0x0200)
+#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 (0x0300)
+#define U300_SYSCON_PMC2R_APP_MISC_2_MASK (0x0C00)
+#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM (0x0400)
+#define U300_SYSCON_PMC2R_APP_MISC_2_MMC (0x0800)
+#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 (0x0C00)
+#define U300_SYSCON_PMC2R_APP_MISC_3_MASK (0x3000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM (0x1000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_MMC (0x2000)
+#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 (0x3000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_MASK (0xC000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM (0x4000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_MMC (0x8000)
+#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO (0xC000)
/* TODO: More SYSCON registers missing */
#define U300_SYSCON_PMC3R (0x10c)
#define U300_SYSCON_PMC3R_APP_MISC_11_MASK (0xc000)
#define U300_SYSCON_PMC3R_APP_MISC_11_SPI (0x4000)
#define U300_SYSCON_PMC3R_APP_MISC_10_MASK (0x3000)
#define U300_SYSCON_PMC3R_APP_MISC_10_SPI (0x1000)
-/* TODO: Missing other configs, I just added the SPI stuff */
-
+/* TODO: Missing other configs */
+#define U300_SYSCON_PMC4R (0x168)
+#define U300_SYSCON_PMC4R_APP_MISC_12_MASK (0x0003)
+#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_13_MASK (0x000C)
+#define U300_SYSCON_PMC4R_APP_MISC_13_CDI (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA (0x0004)
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 (0x0008)
+#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO (0x000C)
+#define U300_SYSCON_PMC4R_APP_MISC_14_MASK (0x0030)
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA (0x0010)
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 (0x0020)
+#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO (0x0030)
+#define U300_SYSCON_PMC4R_APP_MISC_16_MASK (0x0300)
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 (0x0000)
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS (0x0100)
+#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N (0x0200)
/* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
#define U300_SYSCON_S0CCR (0x120)
#define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF)
#define U300_SYSCON_S0CCR_CLOCK_REQ (0x4000)
+#define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR (0x2000)
#define U300_SYSCON_S0CCR_CLOCK_INV (0x0200)
#define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK (0x01E0)
#define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK (0x001E)
#define U300_SYSCON_S1CCR (0x124)
#define U300_SYSCON_S1CCR_FIELD_MASK (0x43FF)
#define U300_SYSCON_S1CCR_CLOCK_REQ (0x4000)
+#define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR (0x2000)
#define U300_SYSCON_S1CCR_CLOCK_INV (0x0200)
#define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK (0x01E0)
#define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK (0x001E)
#define U300_SYSCON_S2CCR_FIELD_MASK (0xC3FF)
#define U300_SYSCON_S2CCR_CLK_STEAL (0x8000)
#define U300_SYSCON_S2CCR_CLOCK_REQ (0x4000)
+#define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR (0x2000)
#define U300_SYSCON_S2CCR_CLOCK_INV (0x0200)
#define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK (0x01E0)
#define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK (0x001E)
#define U300_SYSCON_MCR_PMGEN_CR_0_EMIF_0_SDRAM (0x000C)
#define U300_SYSCON_MCR_PM1G_MODE_ENABLE (0x0002)
#define U300_SYSCON_MCR_PMTG5_MODE_ENABLE (0x0001)
+/* SC_PLL_IRQ_CONTROL 16bit (R/W) */
+#define U300_SYSCON_PICR (0x0130)
+#define U300_SYSCON_PICR_MASK (0x00FF)
+#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE (0x0080)
+#define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE (0x0040)
+#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE (0x0020)
+#define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE (0x0010)
+#define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE (0x0008)
+#define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE (0x0004)
+#define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE (0x0002)
+#define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE (0x0001)
+/* SC_PLL_IRQ_STATUS 16 bit (R/-) */
+#define U300_SYSCON_PISR (0x0134)
+#define U300_SYSCON_PISR_MASK (0x000F)
+#define U300_SYSCON_PISR_PLL13_UNLOCK_IND (0x0008)
+#define U300_SYSCON_PISR_PLL13_LOCK_IND (0x0004)
+#define U300_SYSCON_PISR_PLL208_UNLOCK_IND (0x0002)
+#define U300_SYSCON_PISR_PLL208_LOCK_IND (0x0001)
+/* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
+#define U300_SYSCON_PICLR (0x0138)
+#define U300_SYSCON_PICLR_MASK (0x000F)
+#define U300_SYSCON_PICLR_RWMASK (0x0000)
+#define U300_SYSCON_PICLR_PLL13_UNLOCK_SC (0x0008)
+#define U300_SYSCON_PICLR_PLL13_LOCK_SC (0x0004)
+#define U300_SYSCON_PICLR_PLL208_UNLOCK_SC (0x0002)
+#define U300_SYSCON_PICLR_PLL208_LOCK_SC (0x0001)
+/* CAMIF_CONTROL 16 bit (-/W) */
+#define U300_SYSCON_CICR (0x013C)
+#define U300_SYSCON_CICR_MASK (0x0FFF)
+#define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_MASK (0x0F00)
+#define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_PORT1 (0x0C00)
+#define U300_SYSCON_CICR_APP_SUBLVDS_TESTMODE_PORT0 (0x0300)
+#define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_MASK (0x00F0)
+#define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_PORT1 (0x00C0)
+#define U300_SYSCON_CICR_APP_SUBLVDS_RESCON_PORT0 (0x0030)
+#define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_MASK (0x000F)
+#define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_PORT1 (0x000C)
+#define U300_SYSCON_CICR_APP_SUBLVDS_PWR_DWN_N_PORT0 (0x0003)
/* Clock activity observability register 0 */
#define U300_SYSCON_C0OAR (0x140)
#define U300_SYSCON_C0OAR_MASK (0xFFFF)
/**
* CPU medium frequency in MHz
*/
-#define SYSCON_CPU_CLOCK_MEDIUM 104
+#define SYSCON_CPU_CLOCK_MEDIUM 52
/**
* CPU low frequency in MHz
*/
/**
* EMIF medium frequency in MHz
*/
-#define SYSCON_EMIF_CLOCK_MEDIUM 104
+#define SYSCON_EMIF_CLOCK_MEDIUM 52
/**
* EMIF low frequency in MHz
*/
/**
* AHB medium frequency in MHz
*/
-#define SYSCON_AHB_CLOCK_MEDIUM 52
+#define SYSCON_AHB_CLOCK_MEDIUM 26
/**
* AHB low frequency in MHz
*/
SYSCON_BM_VIDEO_ENC
};
+/* Selectr a resistor or a set of resistors */
+enum syscon_pull_up_down {
+ SYSCON_PU_KEY_IN_EN,
+ SYSCON_PU_EMIF_1_8_BIT_EN,
+ SYSCON_PU_EMIF_1_16_BIT_EN,
+ SYSCON_PU_EMIF_1_NFIF_READY_EN,
+ SYSCON_PU_EMIF_1_NFIF_WAIT_N_EN,
+};
+
/*
* Note that this array must match the order of the array "clk_reg"
* in syscon.c
SYSCON_CLKCONTROL_SPI,
SYSCON_CLKCONTROL_I2S0_CORE,
SYSCON_CLKCONTROL_I2S1_CORE,
+ SYSCON_CLKCONTROL_UART1,
SYSCON_CLKCONTROL_AAIF,
SYSCON_CLKCONTROL_AHB,
SYSCON_CLKCONTROL_APEX,
enum syscon_sysclk_req {
SYSCON_SYSCLKREQ_DISABLED,
- SYSCON_SYSCLKREQ_ACTIVE_LOW
+ SYSCON_SYSCLKREQ_ACTIVE_LOW,
+ SYSCON_SYSCLKREQ_MONITOR
};
enum syscon_clk_mode {
#include <linux/regulator/consumer.h>
#include <linux/regulator/machine.h>
#include <linux/gpio.h>
+#include <linux/amba/mmci.h>
-#include <asm/mach/mmc.h>
#include "mmc.h"
+#include "padmux.h"
struct mmci_card_event {
struct input_dev *mmc_input;
int mmc_inserted;
struct work_struct workq;
- struct mmc_platform_data mmc0_plat_data;
+ struct mmci_platform_data mmc0_plat_data;
};
static unsigned int mmc_status(struct device *dev)
{
struct mmci_card_event *mmci_card;
struct device *mmcsd_device = &adev->dev;
+ struct pmx *pmx;
int ret = 0;
mmci_card = kzalloc(sizeof(struct mmci_card_event), GFP_KERNEL);
mmci_card->mmc0_plat_data.status = mmc_status;
mmci_card->mmc0_plat_data.gpio_wp = -1;
mmci_card->mmc0_plat_data.gpio_cd = -1;
+ mmci_card->mmc0_plat_data.capabilities = MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA;
mmcsd_device->platform_data = (void *) &mmci_card->mmc0_plat_data;
input_set_drvdata(mmci_card->mmc_input, mmci_card);
+ /*
+ * Setup padmuxing for MMC. Since this must always be
+ * compiled into the kernel, pmx is never released.
+ */
+ pmx = pmx_get(mmcsd_device, U300_APP_PMX_MMC_SETTING);
+
+ if (IS_ERR(pmx))
+ pr_warning("Could not get padmux handle\n");
+ else {
+ ret = pmx_activate(mmcsd_device, pmx);
+ if (IS_ERR_VALUE(ret))
+ pr_warning("Could not activate padmuxing\n");
+ }
+
ret = gpio_register_callback(U300_GPIO_PIN_MMC_CD, mmci_callback,
mmci_card);
* Copyright (C) 2009 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* U300 PADMUX functions
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- *
+ * Author: Martin Persson <martin.persson@stericsson.com>
*/
-#include <linux/io.h>
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/mutex.h>
+#include <linux/string.h>
+#include <linux/bug.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
#include <mach/u300-regs.h>
#include <mach/syscon.h>
-
#include "padmux.h"
-/* Set the PAD MUX to route the MMC reader correctly to GPIO0. */
-void pmx_set_mission_mode_mmc(void)
-{
- u16 val;
-
- val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMC1LR);
- val &= ~U300_SYSCON_PMC1LR_MMCSD_MASK;
- writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMC1LR);
- val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
- val &= ~U300_SYSCON_PMC1HR_APP_GPIO_1_MASK;
- val |= U300_SYSCON_PMC1HR_APP_GPIO_1_MMC;
- writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
-}
-
-void pmx_set_mission_mode_spi(void)
-{
- u16 val;
-
- /* Set up padmuxing so the SPI port and its chipselects are active */
- val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
- /*
- * Activate the SPI port (disable the use of these pins for generic
- * GPIO, DSP, AAIF
- */
- val &= ~U300_SYSCON_PMC1HR_APP_SPI_2_MASK;
- val |= U300_SYSCON_PMC1HR_APP_SPI_2_SPI;
- /*
- * Use GPIO pin SPI CS1 for CS1 actually (it can be used for other
- * things also)
- */
- val &= ~U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK;
- val |= U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI;
- /*
- * Use GPIO pin SPI CS2 for CS2 actually (it can be used for other
- * things also)
- */
- val &= ~U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK;
- val |= U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI;
- writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMC1HR);
+static DEFINE_MUTEX(pmx_mutex);
+
+const u32 pmx_registers[] = {
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC1LR),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC1HR),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC2R),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC3R),
+ (U300_SYSCON_VBASE + U300_SYSCON_PMC4R)
+};
+
+/* High level functionality */
+
+/* Lazy dog:
+ * onmask = {
+ * {"PMC1LR" mask, "PMC1LR" value},
+ * {"PMC1HR" mask, "PMC1HR" value},
+ * {"PMC2R" mask, "PMC2R" value},
+ * {"PMC3R" mask, "PMC3R" value},
+ * {"PMC4R" mask, "PMC4R" value}
+ * }
+ */
+static struct pmx mmc_setting = {
+ .setting = U300_APP_PMX_MMC_SETTING,
+ .default_on = false,
+ .activated = false,
+ .name = "MMC",
+ .onmask = {
+ {U300_SYSCON_PMC1LR_MMCSD_MASK,
+ U300_SYSCON_PMC1LR_MMCSD_MMCSD},
+ {0, 0},
+ {0, 0},
+ {0, 0},
+ {U300_SYSCON_PMC4R_APP_MISC_12_MASK,
+ U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO}
+ },
+};
+
+static struct pmx spi_setting = {
+ .setting = U300_APP_PMX_SPI_SETTING,
+ .default_on = false,
+ .activated = false,
+ .name = "SPI",
+ .onmask = {{0, 0},
+ {U300_SYSCON_PMC1HR_APP_SPI_2_MASK |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK,
+ U300_SYSCON_PMC1HR_APP_SPI_2_SPI |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI |
+ U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI},
+ {0, 0},
+ {0, 0},
+ {0, 0}
+ },
+};
+
+/* Available padmux settings */
+static struct pmx *pmx_settings[] = {
+ &mmc_setting,
+ &spi_setting,
+};
+
+static void update_registers(struct pmx *pmx, bool activate)
+{
+ u16 regval, val, mask;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(pmx_registers); i++) {
+ if (activate)
+ val = pmx->onmask[i].val;
+ else
+ val = 0;
+
+ mask = pmx->onmask[i].mask;
+ if (mask != 0) {
+ regval = readw(pmx_registers[i]);
+ regval &= ~mask;
+ regval |= val;
+ writew(regval, pmx_registers[i]);
+ }
+ }
+}
+
+struct pmx *pmx_get(struct device *dev, enum pmx_settings setting)
+{
+ int i;
+ struct pmx *pmx = ERR_PTR(-ENOENT);
+
+ if (dev == NULL)
+ return ERR_PTR(-EINVAL);
+
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (setting == pmx_settings[i]->setting) {
+
+ if (pmx_settings[i]->dev != NULL) {
+ WARN(1, "padmux: required setting "
+ "in use by another consumer\n");
+ } else {
+ pmx = pmx_settings[i];
+ pmx->dev = dev;
+ dev_dbg(dev, "padmux: setting nr %d is now "
+ "bound to %s and ready to use\n",
+ setting, dev_name(dev));
+ break;
+ }
+ }
+ }
+ mutex_unlock(&pmx_mutex);
+
+ return pmx;
+}
+EXPORT_SYMBOL(pmx_get);
+
+int pmx_put(struct device *dev, struct pmx *pmx)
+{
+ int i;
+ int ret = -ENOENT;
+
+ if (pmx == NULL || dev == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (pmx->setting == pmx_settings[i]->setting) {
+
+ if (dev != pmx->dev) {
+ WARN(1, "padmux: cannot release handle as "
+ "it is bound to another consumer\n");
+ ret = -EINVAL;
+ break;
+ } else {
+ pmx_settings[i]->dev = NULL;
+ ret = 0;
+ break;
+ }
+ }
+ }
+ mutex_unlock(&pmx_mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL(pmx_put);
+
+int pmx_activate(struct device *dev, struct pmx *pmx)
+{
+ int i, j, ret;
+ ret = 0;
+
+ if (pmx == NULL || dev == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pmx_mutex);
+
+ /* Make sure the required bits are not used */
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (pmx_settings[i]->dev == NULL || pmx_settings[i] == pmx)
+ continue;
+
+ for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) {
+
+ if (pmx_settings[i]->onmask[j].mask & pmx->
+ onmask[j].mask) {
+ /* More than one entry on the same bits */
+ WARN(1, "padmux: cannot activate "
+ "setting. Bit conflict with "
+ "an active setting\n");
+
+ ret = -EUSERS;
+ goto exit;
+ }
+ }
+ }
+ update_registers(pmx, true);
+ pmx->activated = true;
+ dev_dbg(dev, "padmux: setting nr %d is activated\n",
+ pmx->setting);
+
+exit:
+ mutex_unlock(&pmx_mutex);
+ return ret;
+}
+EXPORT_SYMBOL(pmx_activate);
+
+int pmx_deactivate(struct device *dev, struct pmx *pmx)
+{
+ int i;
+ int ret = -ENOENT;
+
+ if (pmx == NULL || dev == NULL)
+ return -EINVAL;
+
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (pmx_settings[i]->dev == NULL)
+ continue;
+
+ if (pmx->setting == pmx_settings[i]->setting) {
+
+ if (dev != pmx->dev) {
+ WARN(1, "padmux: cannot deactivate "
+ "pmx setting as it was activated "
+ "by another consumer\n");
+
+ ret = -EBUSY;
+ continue;
+ } else {
+ update_registers(pmx, false);
+ pmx_settings[i]->dev = NULL;
+ pmx->activated = false;
+ ret = 0;
+ dev_dbg(dev, "padmux: setting nr %d is deactivated",
+ pmx->setting);
+ break;
+ }
+ }
+ }
+ mutex_unlock(&pmx_mutex);
+
+ return ret;
+}
+EXPORT_SYMBOL(pmx_deactivate);
+
+/*
+ * For internal use only. If it is to be exported,
+ * it should be reentrant. Notice that pmx_activate
+ * (i.e. runtime settings) always override default settings.
+ */
+static int pmx_set_default(void)
+{
+ /* Used to identify several entries on the same bits */
+ u16 modbits[ARRAY_SIZE(pmx_registers)];
+
+ int i, j;
+
+ memset(modbits, 0, ARRAY_SIZE(pmx_registers) * sizeof(u16));
+
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+
+ if (!pmx_settings[i]->default_on)
+ continue;
+
+ for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) {
+
+ /* Make sure there is only one entry on the same bits */
+ if (modbits[j] & pmx_settings[i]->onmask[j].mask) {
+ BUG();
+ return -EUSERS;
+ }
+ modbits[j] |= pmx_settings[i]->onmask[j].mask;
+ }
+ update_registers(pmx_settings[i], true);
+ }
+ return 0;
}
+
+#if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG))
+static int pmx_show(struct seq_file *s, void *data)
+{
+ int i;
+ seq_printf(s, "-------------------------------------------------\n");
+ seq_printf(s, "SETTING BOUND TO DEVICE STATE\n");
+ seq_printf(s, "-------------------------------------------------\n");
+ mutex_lock(&pmx_mutex);
+ for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
+ /* Format pmx and device name nicely */
+ char cdp[33];
+ int chars;
+
+ chars = snprintf(&cdp[0], 17, "%s", pmx_settings[i]->name);
+ while (chars < 16) {
+ cdp[chars] = ' ';
+ chars++;
+ }
+ chars = snprintf(&cdp[16], 17, "%s", pmx_settings[i]->dev ?
+ dev_name(pmx_settings[i]->dev) : "N/A");
+ while (chars < 16) {
+ cdp[chars+16] = ' ';
+ chars++;
+ }
+ cdp[32] = '\0';
+
+ seq_printf(s,
+ "%s\t%s\n",
+ &cdp[0],
+ pmx_settings[i]->activated ?
+ "ACTIVATED" : "DEACTIVATED"
+ );
+
+ }
+ mutex_unlock(&pmx_mutex);
+ return 0;
+}
+
+static int pmx_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, pmx_show, NULL);
+}
+
+static const struct file_operations pmx_operations = {
+ .owner = THIS_MODULE,
+ .open = pmx_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static int __init init_pmx_read_debugfs(void)
+{
+ /* Expose a simple debugfs interface to view pmx settings */
+ (void) debugfs_create_file("padmux", S_IFREG | S_IRUGO,
+ NULL, NULL,
+ &pmx_operations);
+ return 0;
+}
+
+/*
+ * This needs to come in after the core_initcall(),
+ * because debugfs is not available until
+ * the subsystems come up.
+ */
+module_init(init_pmx_read_debugfs);
+#endif
+
+static int __init pmx_init(void)
+{
+ int ret;
+
+ ret = pmx_set_default();
+
+ if (IS_ERR_VALUE(ret))
+ pr_crit("padmux: default settings could not be set\n");
+
+ return 0;
+}
+
+/* Should be initialized before consumers */
+core_initcall(pmx_init);
* Copyright (C) 2009 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* U300 PADMUX API
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- *
+ * Author: Martin Persson <martin.persson@stericsson.com>
*/
#ifndef __MACH_U300_PADMUX_H
#define __MACH_U300_PADMUX_H
-void pmx_set_mission_mode_mmc(void);
-void pmx_set_mission_mode_spi(void);
+enum pmx_settings {
+ U300_APP_PMX_MMC_SETTING,
+ U300_APP_PMX_SPI_SETTING
+};
+
+struct pmx_onmask {
+ u16 mask; /* Mask bits */
+ u16 val; /* Value when active */
+};
+
+struct pmx {
+ struct device *dev;
+ enum pmx_settings setting;
+ char *name;
+ bool activated;
+ bool default_on;
+ struct pmx_onmask onmask[];
+};
+
+struct pmx *pmx_get(struct device *dev, enum pmx_settings setting);
+int pmx_put(struct device *dev, struct pmx *pmx);
+int pmx_activate(struct device *dev, struct pmx *pmx);
+int pmx_deactivate(struct device *dev, struct pmx *pmx);
#endif
--- /dev/null
+/*
+ * arch/arm/mach-u300/spi.c
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#include <linux/device.h>
+#include <linux/amba/bus.h>
+#include <linux/spi/spi.h>
+#include <linux/amba/pl022.h>
+#include <linux/err.h>
+#include "padmux.h"
+
+/*
+ * The following is for the actual devices on the SSP/SPI bus
+ */
+#ifdef CONFIG_MACH_U300_SPIDUMMY
+static void select_dummy_chip(u32 chipselect)
+{
+ pr_debug("CORE: %s called with CS=0x%x (%s)\n",
+ __func__,
+ chipselect,
+ chipselect ? "unselect chip" : "select chip");
+ /*
+ * Here you would write the chip select value to the GPIO pins if
+ * this was a real chip (but this is a loopback dummy).
+ */
+}
+
+struct pl022_config_chip dummy_chip_info = {
+ /* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
+ .lbm = LOOPBACK_ENABLED,
+ /*
+ * available POLLING_TRANSFER and INTERRUPT_TRANSFER,
+ * DMA_TRANSFER does not work
+ */
+ .com_mode = INTERRUPT_TRANSFER,
+ .iface = SSP_INTERFACE_MOTOROLA_SPI,
+ /* We can only act as master but SSP_SLAVE is possible in theory */
+ .hierarchy = SSP_MASTER,
+ /* 0 = drive TX even as slave, 1 = do not drive TX as slave */
+ .slave_tx_disable = 0,
+ /* LSB first */
+ .endian_tx = SSP_TX_LSB,
+ .endian_rx = SSP_RX_LSB,
+ .data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
+ .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
+ .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
+ .clk_phase = SSP_CLK_SECOND_EDGE,
+ .clk_pol = SSP_CLK_POL_IDLE_LOW,
+ .ctrl_len = SSP_BITS_12,
+ .wait_state = SSP_MWIRE_WAIT_ZERO,
+ .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
+ /*
+ * This is where you insert a call to a function to enable CS
+ * (usually GPIO) for a certain chip.
+ */
+ .cs_control = select_dummy_chip,
+};
+#endif
+
+static struct spi_board_info u300_spi_devices[] = {
+#ifdef CONFIG_MACH_U300_SPIDUMMY
+ {
+ /* A dummy chip used for loopback tests */
+ .modalias = "spi-dummy",
+ /* Really dummy, pass in additional chip config here */
+ .platform_data = NULL,
+ /* This defines how the controller shall handle the device */
+ .controller_data = &dummy_chip_info,
+ /* .irq - no external IRQ routed from this device */
+ .max_speed_hz = 1000000,
+ .bus_num = 0, /* Only one bus on this chip */
+ .chip_select = 0,
+ /* Means SPI_CS_HIGH, change if e.g low CS */
+ .mode = 0,
+ },
+#endif
+};
+
+static struct pl022_ssp_controller ssp_platform_data = {
+ /* If you have several SPI buses this varies, we have only bus 0 */
+ .bus_id = 0,
+ /* Set this to 1 when we think we got DMA working */
+ .enable_dma = 0,
+ /*
+ * On the APP CPU GPIO 4, 5 and 6 are connected as generic
+ * chip selects for SPI. (Same on U330, U335 and U365.)
+ * TODO: make sure the GPIO driver can select these properly
+ * and do padmuxing accordingly too.
+ */
+ .num_chipselect = 3,
+};
+
+
+void __init u300_spi_init(struct amba_device *adev)
+{
+ struct pmx *pmx;
+
+ adev->dev.platform_data = &ssp_platform_data;
+ /*
+ * Setup padmuxing for SPI. Since this must always be
+ * compiled into the kernel, pmx is never released.
+ */
+ pmx = pmx_get(&adev->dev, U300_APP_PMX_SPI_SETTING);
+
+ if (IS_ERR(pmx))
+ dev_warn(&adev->dev, "Could not get padmux handle\n");
+ else {
+ int ret;
+
+ ret = pmx_activate(&adev->dev, pmx);
+ if (IS_ERR_VALUE(ret))
+ dev_warn(&adev->dev, "Could not activate padmuxing\n");
+ }
+
+}
+void __init u300_spi_register_board_devices(void)
+{
+ /* Register any SPI devices */
+ spi_register_board_info(u300_spi_devices, ARRAY_SIZE(u300_spi_devices));
+}
--- /dev/null
+/*
+ * arch/arm/mach-u300/spi.h
+ *
+ * Copyright (C) 2009 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Author: Linus Walleij <linus.walleij@stericsson.com>
+ */
+#ifndef SPI_H
+#define SPI_H
+#include <linux/amba/bus.h>
+
+#ifdef CONFIG_SPI_PL022
+void __init u300_spi_init(struct amba_device *adev);
+void __init u300_spi_register_board_devices(void);
+#else
+/* Compile out SPI support if PL022 is not selected */
+static inline void __init u300_spi_init(struct amba_device *adev)
+{
+}
+static inline void __init u300_spi_register_board_devices(void)
+{
+}
+#endif
+
+#endif
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
+/*
+ * Override the global weak sched_clock symbol with this
+ * local implementation which uses the clocksource to get some
+ * better resolution when scheduling the kernel. We accept that
+ * this wraps around for now, since it is just a relative time
+ * stamp. (Inspired by OMAP implementation.)
+ */
+unsigned long long notrace sched_clock(void)
+{
+ return clocksource_cyc2ns(clocksource_u300_1mhz.read(
+ &clocksource_u300_1mhz),
+ clocksource_u300_1mhz.mult,
+ clocksource_u300_1mhz.shift);
+}
+
/*
* This sets up the system timers, clock source and clock event.
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/clocksource.h>
#include <linux/clockchips.h>
#include <linux/cnt32_to_63.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
#include "core.h"
#include "clock.h"
return readl(VERSATILE_SYSMCI) & mask;
}
-static struct mmc_platform_data mmc0_plat_data = {
+static struct mmci_platform_data mmc0_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
#include <linux/sysdev.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl061.h>
+#include <linux/amba/mmci.h>
#include <linux/io.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
-#include <asm/mach/mmc.h>
#include "core.h"
#define IRQ_MMCI1A IRQ_SIC_MMCI1A
#endif
-static struct mmc_platform_data mmc1_plat_data = {
+static struct mmci_platform_data mmc1_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = mmc_status,
.gpio_wp = -1,
select CPU_CP15_MMU
select CPU_COPY_V3 if MMU
select CPU_TLB_V3 if MMU
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
help
The ARM610 is the successor to the ARM3 processor
and was produced by VLSI Technology Inc.
depends on !MMU
select CPU_32v4T
select CPU_ABRT_LV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4
help
A 32-bit RISC microprocessor based on the ARM7 processor core
select CPU_CP15_MMU
select CPU_COPY_V3 if MMU
select CPU_TLB_V3 if MMU
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
help
A 32-bit RISC microprocessor based on the ARM7 processor core
designed by Advanced RISC Machines Ltd. The ARM710 is the
bool "Support ARM720T processor" if ARCH_INTEGRATOR
select CPU_32v4T
select CPU_ABRT_LV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4
select CPU_CACHE_VIVT
select CPU_CP15_MMU
depends on !MMU
select CPU_32v4T
select CPU_ABRT_LV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V3 # although the core is v4t
select CPU_CP15_MPU
help
depends on !MMU
select CPU_32v4T
select CPU_ABRT_NOMMU
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4
help
A 32-bit RISC microprocessor based on the ARM9 processor core
bool "Support ARM920T processor" if ARCH_INTEGRATOR
select CPU_32v4T
select CPU_ABRT_EV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WT
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool "Support ARM922T processor" if ARCH_INTEGRATOR
select CPU_32v4T
select CPU_ABRT_EV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WT
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool "Support ARM925T processor" if ARCH_OMAP1
select CPU_32v4T
select CPU_ABRT_EV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WT
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool "Support ARM926T processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB
select CPU_32v5
select CPU_ABRT_EV5TJ
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_COPY_V4WB if MMU
bool
select CPU_32v4
select CPU_ABRT_EV4
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_CACHE_FA
depends on !MMU
select CPU_32v4T
select CPU_ABRT_NOMMU
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MPU
help
depends on !MMU
select CPU_32v5
select CPU_ABRT_NOMMU
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MPU
help
bool "Support ARM1020T (rev 0) processor" if ARCH_INTEGRATOR
select CPU_32v5
select CPU_ABRT_EV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WT
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool "Support ARM1020E processor" if ARCH_INTEGRATOR
select CPU_32v5
select CPU_ABRT_EV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WT
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool "Support ARM1022E processor" if ARCH_INTEGRATOR
select CPU_32v5
select CPU_ABRT_EV4T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_COPY_V4WB if MMU # can probably do better
bool "Support ARM1026EJ-S processor" if ARCH_INTEGRATOR
select CPU_32v5
select CPU_ABRT_EV5T # But need Jazelle, but EV5TJ ignores bit 10
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_COPY_V4WB if MMU # can probably do better
select CPU_32v3 if ARCH_RPC
select CPU_32v4 if !ARCH_RPC
select CPU_ABRT_EV4
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WB
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool
select CPU_32v4
select CPU_ABRT_EV4
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_V4WB
select CPU_CACHE_VIVT
select CPU_CP15_MMU
bool
select CPU_32v5
select CPU_ABRT_EV5T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_TLB_V4WBI if MMU
bool
select CPU_32v5
select CPU_ABRT_EV5T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_TLB_V4WBI if MMU
bool
select CPU_32v5
select CPU_ABRT_EV5T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_TLB_V4WBI if MMU
bool
select CPU_32v5
select CPU_ABRT_EV5T
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_LEGACY
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_COPY_FEROCEON if MMU
bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX
select CPU_32v6
select CPU_ABRT_EV6
- select CPU_PABRT_NOIFAR
+ select CPU_PABRT_V6
select CPU_CACHE_V6
select CPU_CACHE_VIPT
select CPU_CP15_MMU
select CPU_32v6K
select CPU_32v7
select CPU_ABRT_EV7
- select CPU_PABRT_IFAR
+ select CPU_PABRT_V7
select CPU_CACHE_V7
select CPU_CACHE_VIPT
select CPU_CP15_MMU
config CPU_ABRT_EV7
bool
-config CPU_PABRT_IFAR
+config CPU_PABRT_LEGACY
bool
-config CPU_PABRT_NOIFAR
+config CPU_PABRT_V6
+ bool
+
+config CPU_PABRT_V7
bool
# The cache model
select OUTER_CACHE
help
This option enables the L2 cache on XScale3.
+
+config ARM_L1_CACHE_SHIFT
+ int
+ default 6 if ARCH_OMAP3
+ default 5
obj-$(CONFIG_CPU_ABRT_EV6) += abort-ev6.o
obj-$(CONFIG_CPU_ABRT_EV7) += abort-ev7.o
+obj-$(CONFIG_CPU_PABRT_LEGACY) += pabort-legacy.o
+obj-$(CONFIG_CPU_PABRT_V6) += pabort-v6.o
+obj-$(CONFIG_CPU_PABRT_V7) += pabort-v7.o
+
obj-$(CONFIG_CPU_CACHE_V3) += cache-v3.o
obj-$(CONFIG_CPU_CACHE_V4) += cache-v4.o
obj-$(CONFIG_CPU_CACHE_V4WT) += cache-v4wt.o
#include "fault.h"
+/*
+ * Fault status register encodings. We steal bit 31 for our own purposes.
+ */
+#define FSR_LNX_PF (1 << 31)
+#define FSR_WRITE (1 << 11)
+#define FSR_FS4 (1 << 10)
+#define FSR_FS3_0 (15)
+
+static inline int fsr_fs(unsigned int fsr)
+{
+ return (fsr & FSR_FS3_0) | (fsr & FSR_FS4) >> 6;
+}
+
#ifdef CONFIG_MMU
#ifdef CONFIG_KPROBES
#define VM_FAULT_BADMAP 0x010000
#define VM_FAULT_BADACCESS 0x020000
-static int
+/*
+ * Check that the permissions on the VMA allow for the fault which occurred.
+ * If we encountered a write fault, we must have write permission, otherwise
+ * we allow any permission.
+ */
+static inline bool access_error(unsigned int fsr, struct vm_area_struct *vma)
+{
+ unsigned int mask = VM_READ | VM_WRITE | VM_EXEC;
+
+ if (fsr & FSR_WRITE)
+ mask = VM_WRITE;
+ if (fsr & FSR_LNX_PF)
+ mask = VM_EXEC;
+
+ return vma->vm_flags & mask ? false : true;
+}
+
+static int __kprobes
__do_page_fault(struct mm_struct *mm, unsigned long addr, unsigned int fsr,
struct task_struct *tsk)
{
struct vm_area_struct *vma;
- int fault, mask;
+ int fault;
vma = find_vma(mm, addr);
fault = VM_FAULT_BADMAP;
- if (!vma)
+ if (unlikely(!vma))
goto out;
- if (vma->vm_start > addr)
+ if (unlikely(vma->vm_start > addr))
goto check_stack;
/*
* memory access, so we can handle it.
*/
good_area:
- if (fsr & (1 << 11)) /* write? */
- mask = VM_WRITE;
- else
- mask = VM_READ|VM_EXEC|VM_WRITE;
-
- fault = VM_FAULT_BADACCESS;
- if (!(vma->vm_flags & mask))
+ if (access_error(fsr, vma)) {
+ fault = VM_FAULT_BADACCESS;
goto out;
+ }
/*
- * If for any reason at all we couldn't handle
- * the fault, make sure we exit gracefully rather
- * than endlessly redo the fault.
+ * If for any reason at all we couldn't handle the fault, make
+ * sure we exit gracefully rather than endlessly redo the fault.
*/
-survive:
- fault = handle_mm_fault(mm, vma, addr & PAGE_MASK, (fsr & (1 << 11)) ? FAULT_FLAG_WRITE : 0);
- if (unlikely(fault & VM_FAULT_ERROR)) {
- if (fault & VM_FAULT_OOM)
- goto out_of_memory;
- else if (fault & VM_FAULT_SIGBUS)
- return fault;
- BUG();
- }
+ fault = handle_mm_fault(mm, vma, addr & PAGE_MASK, (fsr & FSR_WRITE) ? FAULT_FLAG_WRITE : 0);
+ if (unlikely(fault & VM_FAULT_ERROR))
+ return fault;
if (fault & VM_FAULT_MAJOR)
tsk->maj_flt++;
else
tsk->min_flt++;
return fault;
-out_of_memory:
- if (!is_global_init(tsk))
- goto out;
-
- /*
- * If we are out of memory for pid1, sleep for a while and retry
- */
- up_read(&mm->mmap_sem);
- yield();
- down_read(&mm->mmap_sem);
- goto survive;
-
check_stack:
if (vma->vm_flags & VM_GROWSDOWN && !expand_stack(vma, addr))
goto good_area;
if (!user_mode(regs) && !search_exception_tables(regs->ARM_pc))
goto no_context;
down_read(&mm->mmap_sem);
+ } else {
+ /*
+ * The above down_read_trylock() might have succeeded in
+ * which case, we'll have missed the might_sleep() from
+ * down_read()
+ */
+ might_sleep();
}
fault = __do_page_fault(mm, addr, fsr, tsk);
if (likely(!(fault & (VM_FAULT_ERROR | VM_FAULT_BADMAP | VM_FAULT_BADACCESS))))
return 0;
+ if (fault & VM_FAULT_OOM) {
+ /*
+ * We ran out of memory, call the OOM killer, and return to
+ * userspace (which will retry the fault, or kill us if we
+ * got oom-killed)
+ */
+ pagefault_out_of_memory();
+ return 0;
+ }
+
/*
* If we are in kernel mode at this point, we
* have no context to handle this fault with.
if (!user_mode(regs))
goto no_context;
- if (fault & VM_FAULT_OOM) {
- /*
- * We ran out of memory, or some other thing
- * happened to us that made us unable to handle
- * the page fault gracefully.
- */
- printk("VM: killing process %s\n", tsk->comm);
- do_group_exit(SIGKILL);
- return 0;
- }
if (fault & VM_FAULT_SIGBUS) {
/*
* We had some memory, but were unable to
asmlinkage void __exception
do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
{
- const struct fsr_info *inf = fsr_info + (fsr & 15) + ((fsr & (1 << 10)) >> 6);
+ const struct fsr_info *inf = fsr_info + fsr_fs(fsr);
struct siginfo info;
- if (!inf->fn(addr, fsr, regs))
+ if (!inf->fn(addr, fsr & ~FSR_LNX_PF, regs))
return;
printk(KERN_ALERT "Unhandled fault: %s (0x%03x) at 0x%08lx\n",
arm_notify_die("", regs, &info, fsr, 0);
}
+
+static struct fsr_info ifsr_info[] = {
+ { do_bad, SIGBUS, 0, "unknown 0" },
+ { do_bad, SIGBUS, 0, "unknown 1" },
+ { do_bad, SIGBUS, 0, "debug event" },
+ { do_bad, SIGSEGV, SEGV_ACCERR, "section access flag fault" },
+ { do_bad, SIGBUS, 0, "unknown 4" },
+ { do_translation_fault, SIGSEGV, SEGV_MAPERR, "section translation fault" },
+ { do_bad, SIGSEGV, SEGV_ACCERR, "page access flag fault" },
+ { do_page_fault, SIGSEGV, SEGV_MAPERR, "page translation fault" },
+ { do_bad, SIGBUS, 0, "external abort on non-linefetch" },
+ { do_bad, SIGSEGV, SEGV_ACCERR, "section domain fault" },
+ { do_bad, SIGBUS, 0, "unknown 10" },
+ { do_bad, SIGSEGV, SEGV_ACCERR, "page domain fault" },
+ { do_bad, SIGBUS, 0, "external abort on translation" },
+ { do_sect_fault, SIGSEGV, SEGV_ACCERR, "section permission fault" },
+ { do_bad, SIGBUS, 0, "external abort on translation" },
+ { do_page_fault, SIGSEGV, SEGV_ACCERR, "page permission fault" },
+ { do_bad, SIGBUS, 0, "unknown 16" },
+ { do_bad, SIGBUS, 0, "unknown 17" },
+ { do_bad, SIGBUS, 0, "unknown 18" },
+ { do_bad, SIGBUS, 0, "unknown 19" },
+ { do_bad, SIGBUS, 0, "unknown 20" },
+ { do_bad, SIGBUS, 0, "unknown 21" },
+ { do_bad, SIGBUS, 0, "unknown 22" },
+ { do_bad, SIGBUS, 0, "unknown 23" },
+ { do_bad, SIGBUS, 0, "unknown 24" },
+ { do_bad, SIGBUS, 0, "unknown 25" },
+ { do_bad, SIGBUS, 0, "unknown 26" },
+ { do_bad, SIGBUS, 0, "unknown 27" },
+ { do_bad, SIGBUS, 0, "unknown 28" },
+ { do_bad, SIGBUS, 0, "unknown 29" },
+ { do_bad, SIGBUS, 0, "unknown 30" },
+ { do_bad, SIGBUS, 0, "unknown 31" },
+};
+
asmlinkage void __exception
-do_PrefetchAbort(unsigned long addr, struct pt_regs *regs)
+do_PrefetchAbort(unsigned long addr, unsigned int ifsr, struct pt_regs *regs)
{
- do_translation_fault(addr, 0, regs);
+ const struct fsr_info *inf = ifsr_info + fsr_fs(ifsr);
+ struct siginfo info;
+
+ if (!inf->fn(addr, ifsr | FSR_LNX_PF, regs))
+ return;
+
+ printk(KERN_ALERT "Unhandled prefetch abort: %s (0x%03x) at 0x%08lx\n",
+ inf->name, ifsr, addr);
+
+ info.si_signo = inf->sig;
+ info.si_errno = 0;
+ info.si_code = inf->code;
+ info.si_addr = (void __user *)addr;
+ arm_notify_die("", regs, &info, ifsr, 0);
}
void free_initmem(void)
{
+#ifdef CONFIG_HAVE_TCM
+ extern char *__tcm_start, *__tcm_end;
+
+ totalram_pages += free_area(__phys_to_pfn(__pa(__tcm_start)),
+ __phys_to_pfn(__pa(__tcm_end)),
+ "TCM link");
+#endif
+
if (!machine_is_integrator() && !machine_is_cintegrator())
totalram_pages += free_area(__phys_to_pfn(__pa(__init_begin)),
__phys_to_pfn(__pa(__init_end)),
{
if (addr < PHYS_OFFSET)
return 0;
- if (addr + size >= __pa(high_memory - 1))
+ if (addr + size > __pa(high_memory - 1) + 1)
return 0;
return 1;
#include <asm/cachetype.h>
#include <asm/setup.h>
#include <asm/sizes.h>
+#include <asm/smp_plat.h>
#include <asm/tlb.h>
#include <asm/highmem.h>
if (meminfo.nr_banks >= NR_BANKS) {
printk(KERN_CRIT "NR_BANKS too low, "
"ignoring high memory\n");
- } else if (cache_is_vipt_aliasing()) {
- printk(KERN_CRIT "HIGHMEM is not yet supported "
- "with VIPT aliasing cache, "
- "ignoring high memory\n");
} else {
memmove(bank + 1, bank,
(meminfo.nr_banks - i) * sizeof(*bank));
bank->size = VMALLOC_MIN - __va(bank->start);
}
#else
+ bank->highmem = highmem;
+
/*
* Check whether this memory bank would entirely overlap
* the vmalloc area.
#endif
j++;
}
+#ifdef CONFIG_HIGHMEM
+ if (highmem) {
+ const char *reason = NULL;
+
+ if (cache_is_vipt_aliasing()) {
+ /*
+ * Interactions between kmap and other mappings
+ * make highmem support with aliasing VIPT caches
+ * rather difficult.
+ */
+ reason = "with VIPT aliasing cache";
+#ifdef CONFIG_SMP
+ } else if (tlb_ops_need_broadcast()) {
+ /*
+ * kmap_high needs to occasionally flush TLB entries,
+ * however, if the TLB entries need to be broadcast
+ * we may deadlock:
+ * kmap_high(irqs off)->flush_all_zero_pkmaps->
+ * flush_tlb_kernel_range->smp_call_function_many
+ * (must not be called with irqs off)
+ */
+ reason = "without hardware TLB ops broadcasting";
+#endif
+ }
+ if (reason) {
+ printk(KERN_CRIT "HIGHMEM is not supported %s, ignoring high memory\n",
+ reason);
+ while (j > 0 && meminfo.bank[j - 1].highmem)
+ j--;
+ }
+ }
+#endif
meminfo.nr_banks = j;
}
--- /dev/null
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: legacy_pabort
+ *
+ * Params : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ * : r1 = Simulated IFSR with section translation fault status
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+ .align 5
+ENTRY(legacy_pabort)
+ mov r1, #5
+ mov pc, lr
+ENDPROC(legacy_pabort)
--- /dev/null
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: v6_pabort
+ *
+ * Params : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ * : r1 = IFSR
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+ .align 5
+ENTRY(v6_pabort)
+ mrc p15, 0, r1, c5, c0, 1 @ get IFSR
+ mov pc, lr
+ENDPROC(v6_pabort)
--- /dev/null
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: v6_pabort
+ *
+ * Params : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ * : r1 = IFSR
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+ .align 5
+ENTRY(v7_pabort)
+ mrc p15, 0, r0, c6, c0, 2 @ get IFAR
+ mrc p15, 0, r1, c5, c0, 1 @ get IFSR
+ mov pc, lr
+ENDPROC(v7_pabort)
.type arm1020_processor_functions, #object
arm1020_processor_functions:
.word v4t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm1020_proc_init
.word cpu_arm1020_proc_fin
.word cpu_arm1020_reset
.type arm1020e_processor_functions, #object
arm1020e_processor_functions:
.word v4t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm1020e_proc_init
.word cpu_arm1020e_proc_fin
.word cpu_arm1020e_reset
.type arm1022_processor_functions, #object
arm1022_processor_functions:
.word v4t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm1022_proc_init
.word cpu_arm1022_proc_fin
.word cpu_arm1022_reset
.type arm1026_processor_functions, #object
arm1026_processor_functions:
.word v5t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm1026_proc_init
.word cpu_arm1026_proc_fin
.word cpu_arm1026_reset
.type arm6_processor_functions, #object
ENTRY(arm6_processor_functions)
.word cpu_arm6_data_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm6_proc_init
.word cpu_arm6_proc_fin
.word cpu_arm6_reset
.type arm7_processor_functions, #object
ENTRY(arm7_processor_functions)
.word cpu_arm7_data_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm7_proc_init
.word cpu_arm7_proc_fin
.word cpu_arm7_reset
.type arm720_processor_functions, #object
ENTRY(arm720_processor_functions)
.word v4t_late_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm720_proc_init
.word cpu_arm720_proc_fin
.word cpu_arm720_reset
.type arm740_processor_functions, #object
ENTRY(arm740_processor_functions)
.word v4t_late_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm740_proc_init
.word cpu_arm740_proc_fin
.word cpu_arm740_reset
.type arm7tdmi_processor_functions, #object
ENTRY(arm7tdmi_processor_functions)
.word v4t_late_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm7tdmi_proc_init
.word cpu_arm7tdmi_proc_fin
.word cpu_arm7tdmi_reset
.type arm920_processor_functions, #object
arm920_processor_functions:
.word v4t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm920_proc_init
.word cpu_arm920_proc_fin
.word cpu_arm920_reset
.type arm922_processor_functions, #object
arm922_processor_functions:
.word v4t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm922_proc_init
.word cpu_arm922_proc_fin
.word cpu_arm922_reset
.type arm925_processor_functions, #object
arm925_processor_functions:
.word v4t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm925_proc_init
.word cpu_arm925_proc_fin
.word cpu_arm925_reset
.type arm926_processor_functions, #object
arm926_processor_functions:
.word v5tj_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm926_proc_init
.word cpu_arm926_proc_fin
.word cpu_arm926_reset
.type arm940_processor_functions, #object
ENTRY(arm940_processor_functions)
.word nommu_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm940_proc_init
.word cpu_arm940_proc_fin
.word cpu_arm940_reset
.type arm946_processor_functions, #object
ENTRY(arm946_processor_functions)
.word nommu_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm946_proc_init
.word cpu_arm946_proc_fin
.word cpu_arm946_reset
.type arm9tdmi_processor_functions, #object
ENTRY(arm9tdmi_processor_functions)
.word nommu_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_arm9tdmi_proc_init
.word cpu_arm9tdmi_proc_fin
.word cpu_arm9tdmi_reset
.type fa526_processor_functions, #object
fa526_processor_functions:
.word v4_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_fa526_proc_init
.word cpu_fa526_proc_fin
.word cpu_fa526_reset
.type feroceon_processor_functions, #object
feroceon_processor_functions:
.word v5t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_feroceon_proc_init
.word cpu_feroceon_proc_fin
.word cpu_feroceon_reset
.type mohawk_processor_functions, #object
mohawk_processor_functions:
.word v5t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_mohawk_proc_init
.word cpu_mohawk_proc_fin
.word cpu_mohawk_reset
.type sa110_processor_functions, #object
ENTRY(sa110_processor_functions)
.word v4_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_sa110_proc_init
.word cpu_sa110_proc_fin
.word cpu_sa110_reset
.type sa1100_processor_functions, #object
ENTRY(sa1100_processor_functions)
.word v4_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_sa1100_proc_init
.word cpu_sa1100_proc_fin
.word cpu_sa1100_reset
.type v6_processor_functions, #object
ENTRY(v6_processor_functions)
.word v6_early_abort
- .word pabort_noifar
+ .word v6_pabort
.word cpu_v6_proc_init
.word cpu_v6_proc_fin
.word cpu_v6_reset
.type v7_processor_functions, #object
ENTRY(v7_processor_functions)
.word v7_early_abort
- .word pabort_ifar
+ .word v7_pabort
.word cpu_v7_proc_init
.word cpu_v7_proc_fin
.word cpu_v7_reset
.type xsc3_processor_functions, #object
ENTRY(xsc3_processor_functions)
.word v5t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_xsc3_proc_init
.word cpu_xsc3_proc_fin
.word cpu_xsc3_reset
.type xscale_processor_functions, #object
ENTRY(xscale_processor_functions)
.word v5t_early_abort
- .word pabort_noifar
+ .word legacy_pabort
.word cpu_xscale_proc_init
.word cpu_xscale_proc_fin
.word cpu_xscale_reset
dma_cap_set(DMA_INTERRUPT, iop3xx_dma_0_data.cap_mask);
#else
dma_cap_set(DMA_MEMCPY, iop3xx_dma_0_data.cap_mask);
- dma_cap_set(DMA_MEMCPY_CRC32C, iop3xx_dma_0_data.cap_mask);
dma_cap_set(DMA_INTERRUPT, iop3xx_dma_0_data.cap_mask);
#endif
dma_cap_set(DMA_INTERRUPT, iop3xx_dma_1_data.cap_mask);
#else
dma_cap_set(DMA_MEMCPY, iop3xx_dma_1_data.cap_mask);
- dma_cap_set(DMA_MEMCPY_CRC32C, iop3xx_dma_1_data.cap_mask);
dma_cap_set(DMA_INTERRUPT, iop3xx_dma_1_data.cap_mask);
#endif
dma_cap_set(DMA_INTERRUPT, iop3xx_aau_data.cap_mask);
#else
dma_cap_set(DMA_XOR, iop3xx_aau_data.cap_mask);
- dma_cap_set(DMA_ZERO_SUM, iop3xx_aau_data.cap_mask);
+ dma_cap_set(DMA_XOR_VAL, iop3xx_aau_data.cap_mask);
dma_cap_set(DMA_MEMSET, iop3xx_aau_data.cap_mask);
dma_cap_set(DMA_INTERRUPT, iop3xx_aau_data.cap_mask);
#endif
*IOP3XX_OUMWTVR0 = 0;
/* Outbound window 1 */
- *IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_BA + IOP3XX_PCI_MEM_WINDOW_SIZE;
+ *IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_BA +
+ IOP3XX_PCI_MEM_WINDOW_SIZE / 2;
*IOP3XX_OUMWTVR1 = 0;
/* BAR 3 ( Disabled ) */
{
u32 timer_ctl;
- ticks_per_jiffy = (tick_rate + HZ/2) / HZ;
+ ticks_per_jiffy = DIV_ROUND_CLOSEST(tick_rate, HZ);
ticks_per_usec = tick_rate / 1000000;
next_jiffy_time = 0xffffffff;
iop_tick_rate = tick_rate;
#ifdef CONFIG_ARCH_OMAP850
static struct gpio_bank gpio_bank_850[7] = {
- { OMAP1_MPUIO_BASE, INT_850_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
+ { OMAP1_MPUIO_VBASE, INT_850_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
{ OMAP850_GPIO1_BASE, INT_850_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_850 },
{ OMAP850_GPIO2_BASE, INT_850_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_850 },
{ OMAP850_GPIO3_BASE, INT_850_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_850 },
#ifndef ASMARM_ARCH_KEYPAD_H
#define ASMARM_ARCH_KEYPAD_H
+#include <linux/input/matrix_keypad.h>
+
struct omap_kp_platform_data {
int rows;
int cols;
#define KEY_PERSISTENT 0x00800000
#define KEYNUM_MASK 0x00EFFFFF
-#define KEY(col, row, val) (((col) << 28) | ((row) << 24) | (val))
-#define PERSISTENT_KEY(col, row) (((col) << 28) | ((row) << 24) | \
- KEY_PERSISTENT)
#endif
*/
AF26_34XX_GPIO0,
AF22_34XX_GPIO9,
+ AG9_34XX_GPIO23,
AH8_34XX_GPIO29,
U8_34XX_GPIO54_OUT,
U8_34XX_GPIO54_DOWN,
L8_34XX_GPIO63,
G25_34XX_GPIO86_OUT,
AG4_34XX_GPIO134_OUT,
+ AF4_34XX_GPIO135_OUT,
AE4_34XX_GPIO136_OUT,
AF6_34XX_GPIO140_UP,
AE6_34XX_GPIO141,
va += bytes;
}
- flush_cache_vmap(new->addr, new->addr + total);
+ flush_cache_vmap((unsigned long)new->addr,
+ (unsigned long)(new->addr + total));
return new->addr;
err_out:
}
va_end = _va + PAGE_SIZE * i;
- flush_cache_vmap(_va, va_end);
+ flush_cache_vmap((unsigned long)_va, (unsigned long)va_end);
}
static inline void sgtable_drain_vmalloc(struct sg_table *sgt)
#include <linux/kernel.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
+#include <linux/dma-mapping.h>
#include <asm/system.h>
#include <asm/irq.h>
+#include <asm/memory.h>
#include <mach/hardware.h>
#include <mach/dma.h>
+#define DMA_DEBUG_NAME "pxa_dma"
+#define DMA_MAX_REQUESTERS 64
+
struct dma_channel {
char *name;
pxa_dma_prio prio;
void (*irq_handler)(int, void *);
void *data;
+ spinlock_t lock;
};
static struct dma_channel *dma_channels;
static int num_dma_channels;
+/*
+ * Debug fs
+ */
+#ifdef CONFIG_DEBUG_FS
+#include <linux/debugfs.h>
+#include <linux/uaccess.h>
+#include <linux/seq_file.h>
+
+static struct dentry *dbgfs_root, *dbgfs_state, **dbgfs_chan;
+
+static int dbg_show_requester_chan(struct seq_file *s, void *p)
+{
+ int pos = 0;
+ int chan = (int)s->private;
+ int i;
+ u32 drcmr;
+
+ pos += seq_printf(s, "DMA channel %d requesters list :\n", chan);
+ for (i = 0; i < DMA_MAX_REQUESTERS; i++) {
+ drcmr = DRCMR(i);
+ if ((drcmr & DRCMR_CHLNUM) == chan)
+ pos += seq_printf(s, "\tRequester %d (MAPVLD=%d)\n", i,
+ !!(drcmr & DRCMR_MAPVLD));
+ }
+ return pos;
+}
+
+static inline int dbg_burst_from_dcmd(u32 dcmd)
+{
+ int burst = (dcmd >> 16) & 0x3;
+
+ return burst ? 4 << burst : 0;
+}
+
+static int is_phys_valid(unsigned long addr)
+{
+ return pfn_valid(__phys_to_pfn(addr));
+}
+
+#define DCSR_STR(flag) (dcsr & DCSR_##flag ? #flag" " : "")
+#define DCMD_STR(flag) (dcmd & DCMD_##flag ? #flag" " : "")
+
+static int dbg_show_descriptors(struct seq_file *s, void *p)
+{
+ int pos = 0;
+ int chan = (int)s->private;
+ int i, max_show = 20, burst, width;
+ u32 dcmd;
+ unsigned long phys_desc;
+ struct pxa_dma_desc *desc;
+ unsigned long flags;
+
+ spin_lock_irqsave(&dma_channels[chan].lock, flags);
+ phys_desc = DDADR(chan);
+
+ pos += seq_printf(s, "DMA channel %d descriptors :\n", chan);
+ pos += seq_printf(s, "[%03d] First descriptor unknown\n", 0);
+ for (i = 1; i < max_show && is_phys_valid(phys_desc); i++) {
+ desc = phys_to_virt(phys_desc);
+ dcmd = desc->dcmd;
+ burst = dbg_burst_from_dcmd(dcmd);
+ width = (1 << ((dcmd >> 14) & 0x3)) >> 1;
+
+ pos += seq_printf(s, "[%03d] Desc at %08lx(virt %p)\n",
+ i, phys_desc, desc);
+ pos += seq_printf(s, "\tDDADR = %08x\n", desc->ddadr);
+ pos += seq_printf(s, "\tDSADR = %08x\n", desc->dsadr);
+ pos += seq_printf(s, "\tDTADR = %08x\n", desc->dtadr);
+ pos += seq_printf(s, "\tDCMD = %08x (%s%s%s%s%s%s%sburst=%d"
+ " width=%d len=%d)\n",
+ dcmd,
+ DCMD_STR(INCSRCADDR), DCMD_STR(INCTRGADDR),
+ DCMD_STR(FLOWSRC), DCMD_STR(FLOWTRG),
+ DCMD_STR(STARTIRQEN), DCMD_STR(ENDIRQEN),
+ DCMD_STR(ENDIAN), burst, width,
+ dcmd & DCMD_LENGTH);
+ phys_desc = desc->ddadr;
+ }
+ if (i == max_show)
+ pos += seq_printf(s, "[%03d] Desc at %08lx ... max display reached\n",
+ i, phys_desc);
+ else
+ pos += seq_printf(s, "[%03d] Desc at %08lx is %s\n",
+ i, phys_desc, phys_desc == DDADR_STOP ?
+ "DDADR_STOP" : "invalid");
+
+ spin_unlock_irqrestore(&dma_channels[chan].lock, flags);
+ return pos;
+}
+
+static int dbg_show_chan_state(struct seq_file *s, void *p)
+{
+ int pos = 0;
+ int chan = (int)s->private;
+ u32 dcsr, dcmd;
+ int burst, width;
+ static char *str_prio[] = { "high", "normal", "low" };
+
+ dcsr = DCSR(chan);
+ dcmd = DCMD(chan);
+ burst = dbg_burst_from_dcmd(dcmd);
+ width = (1 << ((dcmd >> 14) & 0x3)) >> 1;
+
+ pos += seq_printf(s, "DMA channel %d\n", chan);
+ pos += seq_printf(s, "\tPriority : %s\n",
+ str_prio[dma_channels[chan].prio]);
+ pos += seq_printf(s, "\tUnaligned transfer bit: %s\n",
+ DALGN & (1 << chan) ? "yes" : "no");
+ pos += seq_printf(s, "\tDCSR = %08x (%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s)\n",
+ dcsr, DCSR_STR(RUN), DCSR_STR(NODESC),
+ DCSR_STR(STOPIRQEN), DCSR_STR(EORIRQEN),
+ DCSR_STR(EORJMPEN), DCSR_STR(EORSTOPEN),
+ DCSR_STR(SETCMPST), DCSR_STR(CLRCMPST),
+ DCSR_STR(CMPST), DCSR_STR(EORINTR), DCSR_STR(REQPEND),
+ DCSR_STR(STOPSTATE), DCSR_STR(ENDINTR),
+ DCSR_STR(STARTINTR), DCSR_STR(BUSERR));
+
+ pos += seq_printf(s, "\tDCMD = %08x (%s%s%s%s%s%s%sburst=%d width=%d"
+ " len=%d)\n",
+ dcmd,
+ DCMD_STR(INCSRCADDR), DCMD_STR(INCTRGADDR),
+ DCMD_STR(FLOWSRC), DCMD_STR(FLOWTRG),
+ DCMD_STR(STARTIRQEN), DCMD_STR(ENDIRQEN),
+ DCMD_STR(ENDIAN), burst, width, dcmd & DCMD_LENGTH);
+ pos += seq_printf(s, "\tDSADR = %08x\n", DSADR(chan));
+ pos += seq_printf(s, "\tDTADR = %08x\n", DTADR(chan));
+ pos += seq_printf(s, "\tDDADR = %08x\n", DDADR(chan));
+ return pos;
+}
+
+static int dbg_show_state(struct seq_file *s, void *p)
+{
+ int pos = 0;
+
+ /* basic device status */
+ pos += seq_printf(s, "DMA engine status\n");
+ pos += seq_printf(s, "\tChannel number: %d\n", num_dma_channels);
+
+ return pos;
+}
+
+#define DBGFS_FUNC_DECL(name) \
+static int dbg_open_##name(struct inode *inode, struct file *file) \
+{ \
+ return single_open(file, dbg_show_##name, inode->i_private); \
+} \
+static const struct file_operations dbg_fops_##name = { \
+ .owner = THIS_MODULE, \
+ .open = dbg_open_##name, \
+ .llseek = seq_lseek, \
+ .read = seq_read, \
+ .release = single_release, \
+}
+
+DBGFS_FUNC_DECL(state);
+DBGFS_FUNC_DECL(chan_state);
+DBGFS_FUNC_DECL(descriptors);
+DBGFS_FUNC_DECL(requester_chan);
+
+static struct dentry *pxa_dma_dbg_alloc_chan(int ch, struct dentry *chandir)
+{
+ char chan_name[11];
+ struct dentry *chan, *chan_state = NULL, *chan_descr = NULL;
+ struct dentry *chan_reqs = NULL;
+ void *dt;
+
+ scnprintf(chan_name, sizeof(chan_name), "%d", ch);
+ chan = debugfs_create_dir(chan_name, chandir);
+ dt = (void *)ch;
+
+ if (chan)
+ chan_state = debugfs_create_file("state", 0400, chan, dt,
+ &dbg_fops_chan_state);
+ if (chan_state)
+ chan_descr = debugfs_create_file("descriptors", 0400, chan, dt,
+ &dbg_fops_descriptors);
+ if (chan_descr)
+ chan_reqs = debugfs_create_file("requesters", 0400, chan, dt,
+ &dbg_fops_requester_chan);
+ if (!chan_reqs)
+ goto err_state;
+
+ return chan;
+
+err_state:
+ debugfs_remove_recursive(chan);
+ return NULL;
+}
+
+static void pxa_dma_init_debugfs(void)
+{
+ int i;
+ struct dentry *chandir;
+
+ dbgfs_root = debugfs_create_dir(DMA_DEBUG_NAME, NULL);
+ if (IS_ERR(dbgfs_root) || !dbgfs_root)
+ goto err_root;
+
+ dbgfs_state = debugfs_create_file("state", 0400, dbgfs_root, NULL,
+ &dbg_fops_state);
+ if (!dbgfs_state)
+ goto err_state;
+
+ dbgfs_chan = kmalloc(sizeof(*dbgfs_state) * num_dma_channels,
+ GFP_KERNEL);
+ if (!dbgfs_state)
+ goto err_alloc;
+
+ chandir = debugfs_create_dir("channels", dbgfs_root);
+ if (!chandir)
+ goto err_chandir;
+
+ for (i = 0; i < num_dma_channels; i++) {
+ dbgfs_chan[i] = pxa_dma_dbg_alloc_chan(i, chandir);
+ if (!dbgfs_chan[i])
+ goto err_chans;
+ }
+
+ return;
+err_chans:
+err_chandir:
+ kfree(dbgfs_chan);
+err_alloc:
+err_state:
+ debugfs_remove_recursive(dbgfs_root);
+err_root:
+ pr_err("pxa_dma: debugfs is not available\n");
+}
+
+static void __exit pxa_dma_cleanup_debugfs(void)
+{
+ debugfs_remove_recursive(dbgfs_root);
+}
+#else
+static inline void pxa_dma_init_debugfs(void) {}
+static inline void pxa_dma_cleanup_debugfs(void) {}
+#endif
+
int pxa_request_dma (char *name, pxa_dma_prio prio,
void (*irq_handler)(int, void *),
void *data)
local_irq_restore(flags);
return i;
}
+EXPORT_SYMBOL(pxa_request_dma);
void pxa_free_dma (int dma_ch)
{
dma_channels[dma_ch].name = NULL;
local_irq_restore(flags);
}
+EXPORT_SYMBOL(pxa_free_dma);
static irqreturn_t dma_irq_handler(int irq, void *dev_id)
{
int i, dint = DINT;
+ struct dma_channel *channel;
- for (i = 0; i < num_dma_channels; i++) {
- if (dint & (1 << i)) {
- struct dma_channel *channel = &dma_channels[i];
- if (channel->name && channel->irq_handler) {
- channel->irq_handler(i, channel->data);
- } else {
- /*
- * IRQ for an unregistered DMA channel:
- * let's clear the interrupts and disable it.
- */
- printk (KERN_WARNING "spurious IRQ for DMA channel %d\n", i);
- DCSR(i) = DCSR_STARTINTR|DCSR_ENDINTR|DCSR_BUSERR;
- }
+ while (dint) {
+ i = __ffs(dint);
+ dint &= (dint - 1);
+ channel = &dma_channels[i];
+ if (channel->name && channel->irq_handler) {
+ channel->irq_handler(i, channel->data);
+ } else {
+ /*
+ * IRQ for an unregistered DMA channel:
+ * let's clear the interrupts and disable it.
+ */
+ printk (KERN_WARNING "spurious IRQ for DMA channel %d\n", i);
+ DCSR(i) = DCSR_STARTINTR|DCSR_ENDINTR|DCSR_BUSERR;
}
}
return IRQ_HANDLED;
for (i = 0; i < num_ch; i++) {
DCSR(i) = 0;
dma_channels[i].prio = min((i & 0xf) >> 2, DMA_PRIO_LOW);
+ spin_lock_init(&dma_channels[i].lock);
}
ret = request_irq(irq, dma_irq_handler, IRQF_DISABLED, "DMA", NULL);
kfree(dma_channels);
return ret;
}
-
num_dma_channels = num_ch;
+
+ pxa_dma_init_debugfs();
+
return 0;
}
-
-EXPORT_SYMBOL(pxa_request_dma);
-EXPORT_SYMBOL(pxa_free_dma);
MFP_PIN_GPIO125,
MFP_PIN_GPIO126,
MFP_PIN_GPIO127,
+
+ MFP_PIN_GPIO128,
+ MFP_PIN_GPIO129,
+ MFP_PIN_GPIO130,
+ MFP_PIN_GPIO131,
+ MFP_PIN_GPIO132,
+ MFP_PIN_GPIO133,
+ MFP_PIN_GPIO134,
+ MFP_PIN_GPIO135,
+ MFP_PIN_GPIO136,
+ MFP_PIN_GPIO137,
+ MFP_PIN_GPIO138,
+ MFP_PIN_GPIO139,
+ MFP_PIN_GPIO140,
+ MFP_PIN_GPIO141,
+ MFP_PIN_GPIO142,
+ MFP_PIN_GPIO143,
+ MFP_PIN_GPIO144,
+ MFP_PIN_GPIO145,
+ MFP_PIN_GPIO146,
+ MFP_PIN_GPIO147,
+ MFP_PIN_GPIO148,
+ MFP_PIN_GPIO149,
+ MFP_PIN_GPIO150,
+ MFP_PIN_GPIO151,
+ MFP_PIN_GPIO152,
+ MFP_PIN_GPIO153,
+ MFP_PIN_GPIO154,
+ MFP_PIN_GPIO155,
+ MFP_PIN_GPIO156,
+ MFP_PIN_GPIO157,
+ MFP_PIN_GPIO158,
+ MFP_PIN_GPIO159,
+ MFP_PIN_GPIO160,
+ MFP_PIN_GPIO161,
+ MFP_PIN_GPIO162,
+ MFP_PIN_GPIO163,
+ MFP_PIN_GPIO164,
+ MFP_PIN_GPIO165,
+ MFP_PIN_GPIO166,
+ MFP_PIN_GPIO167,
+ MFP_PIN_GPIO168,
+ MFP_PIN_GPIO169,
+ MFP_PIN_GPIO170,
+ MFP_PIN_GPIO171,
+ MFP_PIN_GPIO172,
+ MFP_PIN_GPIO173,
+ MFP_PIN_GPIO174,
+ MFP_PIN_GPIO175,
+ MFP_PIN_GPIO176,
+ MFP_PIN_GPIO177,
+ MFP_PIN_GPIO178,
+ MFP_PIN_GPIO179,
+ MFP_PIN_GPIO180,
+ MFP_PIN_GPIO181,
+ MFP_PIN_GPIO182,
+ MFP_PIN_GPIO183,
+ MFP_PIN_GPIO184,
+ MFP_PIN_GPIO185,
+ MFP_PIN_GPIO186,
+ MFP_PIN_GPIO187,
+ MFP_PIN_GPIO188,
+ MFP_PIN_GPIO189,
+ MFP_PIN_GPIO190,
+ MFP_PIN_GPIO191,
+
+ MFP_PIN_GPIO255 = 255,
+
MFP_PIN_GPIO0_2,
MFP_PIN_GPIO1_2,
MFP_PIN_GPIO2_2,
#define MFP_PULL_LOW (0x1 << 21)
#define MFP_PULL_HIGH (0x2 << 21)
#define MFP_PULL_BOTH (0x3 << 21)
-#define MFP_PULL_MASK (0x3 << 21)
-#define MFP_PULL(x) (((x) >> 21) & 0x3)
+#define MFP_PULL_FLOAT (0x4 << 21)
+#define MFP_PULL_MASK (0x7 << 21)
+#define MFP_PULL(x) (((x) >> 21) & 0x7)
#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
* MFPR_PULL_LOW 1 0 1
* MFPR_PULL_HIGH 1 1 0
* MFPR_PULL_BOTH 1 1 1
+ * MFPR_PULL_FLOAT 1 0 0
*/
#define MFPR_PULL_NONE (0)
#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
+#define MFPR_PULL_FLOAT (MFPR_PULL_SEL)
/* mfp_spin_lock is used to ensure that MFP register configuration
* (most likely a read-modify-write operation) is atomic, and that
MFPR_PULL_LOW,
MFPR_PULL_HIGH,
MFPR_PULL_BOTH,
+ MFPR_PULL_FLOAT,
};
/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
gpn = chip->chip.base;
for (i = 0; i < chip->chip.ngpio; i++, gpn++) {
- BUG_ON(gpn > ARRAY_SIZE(s3c_gpios));
+ BUG_ON(gpn >= ARRAY_SIZE(s3c_gpios));
s3c_gpios[gpn] = chip;
}
}
#define _ARCH_MCI_H
struct s3c24xx_mci_pdata {
+ unsigned int no_wprotect : 1;
+ unsigned int no_detect : 1;
unsigned int wprotect_invert : 1;
unsigned int detect_invert : 1; /* set => detect active high. */
+ unsigned int use_dma : 1;
unsigned int gpio_detect;
unsigned int gpio_wprotect;
if (!chan)
return -EINVAL;
- buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_KERNEL);
+ buff = kzalloc(sizeof(struct s3c64xx_dma_buff), GFP_ATOMIC);
if (!buff) {
printk(KERN_ERR "%s: no memory for buffer\n", __func__);
return -ENOMEM;
}
- lli = dma_pool_alloc(dma_pool, GFP_KERNEL, &buff->lli_dma);
+ lli = dma_pool_alloc(dma_pool, GFP_ATOMIC, &buff->lli_dma);
if (!lli) {
printk(KERN_ERR "%s: no memory for lli\n", __func__);
ret = -ENOMEM;
printk(KERN_INFO "%s: Registering DMA channels\n", __func__);
- dma_pool = dma_pool_create("DMA-LLI", NULL, 32, 16, 0);
+ dma_pool = dma_pool_create("DMA-LLI", NULL, sizeof(struct pl080s_lli), 16, 0);
if (!dma_pool) {
printk(KERN_ERR "%s: failed to create pool\n", __func__);
return -ENOMEM;
struct s3c64xx_dma_buff *next;
void *pw;
- struct pl080_lli *lli;
+ struct pl080s_lli *lli;
dma_addr_t lli_dma;
};
#define IRQ_EINT_GROUP(group, no) (IRQ_EINT_GROUP##group##_BASE + (no))
+/* Define a group of interrupts for board-specific use (eg, for MFD
+ * interrupt controllers). */
+#define IRQ_BOARD_START (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
+
+#define IRQ_BOARD_NR 16
+
+#define IRQ_BOARD_END (IRQ_BOARD_START + IRQ_BOARD_NR)
+
/* Set the default NR_IRQS */
-#define NR_IRQS (IRQ_EINT_GROUP9_BASE + IRQ_EINT_GROUP9_NR + 1)
+#define NR_IRQS (IRQ_BOARD_END + 1)
#endif /* __ASM_PLAT_S3C64XX_IRQS_H */
return -EINVAL;
val = __raw_readl(reg);
- val &= ~(0xf << sclk->shift);
- val |= (div - 1) << sclk->shift;
+ val &= ~(0xf << sclk->divider_shift);
+ val |= (div - 1) << sclk->divider_shift;
__raw_writel(val, reg);
return 0;
clksrc |= src_nr << sclk->shift;
__raw_writel(clksrc, S3C_CLK_SRC);
+
+ clk->parent = parent;
return 0;
}
if (rate > parent_rate)
rate = parent_rate;
else {
- div = rate / parent_rate;
+ div = parent_rate / rate;
if (div == 0)
div = 1;
stmp3xxx_dma_free_command(ch,
&descriptors
[i]);
- } while (i-- >= 0);
+ } while (i-- > 0);
}
return err;
}
#
# http://www.arm.linux.org.uk/developer/machines/?action=new
#
-# Last update: Sat Sep 12 12:00:16 2009
+# Last update: Fri Sep 18 21:42:00 2009
#
# machine_is_xxx CONFIG_xxxx MACH_TYPE_xxx number
#
aml_m8050 MACH_AML_M8050 AML_M8050 1644
mx35_3ds MACH_MX35_3DS MX35_3DS 1645
mars MACH_MARS MARS 1646
-ntosd_644xa MACH_NTOSD_644XA NTOSD_644XA 1647
+neuros_osd2 MACH_NEUROS_OSD2 NEUROS_OSD2 1647
badger MACH_BADGER BADGER 1648
trizeps4wl MACH_TRIZEPS4WL TRIZEPS4WL 1649
trizeps5 MACH_TRIZEPS5 TRIZEPS5 1650
zoran43xx MACH_ZORAN43XX ZORAN43XX 1660
sonix926 MACH_SONIX926 SONIX926 1661
celestialsemi MACH_CELESTIALSEMI CELESTIALSEMI 1662
-cc9m2443 MACH_CC9M2443 CC9M2443 1663
+cc9m2443js MACH_CC9M2443JS CC9M2443JS 1663
tw5334 MACH_TW5334 TW5334 1664
omap_htcartemis MACH_HTCARTEMIS HTCARTEMIS 1665
nal_hlite MACH_NAL_HLITE NAL_HLITE 1666
rd88f5181l_ge MACH_RD88F5181L_GE RD88F5181L_GE 1812
sifmain MACH_SIFMAIN SIFMAIN 1813
sam9_l9261 MACH_SAM9_L9261 SAM9_L9261 1814
-cc9m2443js MACH_CC9M2443JS CC9M2443JS 1815
+cc9m2443 MACH_CC9M2443 CC9M2443 1815
xaria300 MACH_XARIA300 XARIA300 1816
it9200 MACH_IT9200 IT9200 1817
rd88f5181l_fxo MACH_RD88F5181L_FXO RD88F5181L_FXO 1818
pss2 MACH_PSS2 PSS2 2423
davinci_apm150 MACH_DAVINCI_APM150 DAVINCI_APM150 2424
str9100 MACH_STR9100 STR9100 2425
+net5big MACH_NET5BIG NET5BIG 2426
+seabed9263 MACH_SEABED9263 SEABED9263 2427
+mx51_m2id MACH_MX51_M2ID MX51_M2ID 2428
+octvocplus_eb MACH_OCTVOCPLUS_EB OCTVOCPLUS_EB 2429
+klk_firefox MACH_KLK_FIREFOX KLK_FIREFOX 2430
+klk_wirma_module MACH_KLK_WIRMA_MODULE KLK_WIRMA_MODULE 2431
+klk_wirma_mmi MACH_KLK_WIRMA_MMI KLK_WIRMA_MMI 2432
+supersonic MACH_SUPERSONIC SUPERSONIC 2433
+liberty MACH_LIBERTY LIBERTY 2434
+mh355 MACH_MH355 MH355 2435
+pc7802 MACH_PC7802 PC7802 2436
+gnet_sgc MACH_GNET_SGC GNET_SGC 2437
{
__sdata = .;
/* This gets done first, so the glob doesn't suck it in */
- . = ALIGN(32);
- *(.data.cacheline_aligned)
+ CACHELINE_ALIGNED_DATA(32)
#if !L1_DATA_A_LENGTH
. = ALIGN(32);
DATA_DATA
CONSTRUCTORS
- /* make sure the init_task is aligned to the
- * kernel thread size so we can locate the kernel
- * stack properly and quickly.
- */
- . = ALIGN(THREAD_SIZE);
- *(.init_task.data)
+ INIT_TASK_DATA(THREAD_SIZE)
__edata = .;
}
. = ALIGN(PAGE_SIZE);
___init_begin = .;
- .init.text :
- {
- . = ALIGN(PAGE_SIZE);
- __sinittext = .;
- INIT_TEXT
- __einittext = .;
- }
- .init.data :
- {
- . = ALIGN(16);
- INIT_DATA
- }
- .init.setup :
- {
- . = ALIGN(16);
- ___setup_start = .;
- *(.init.setup)
- ___setup_end = .;
- }
- .initcall.init :
- {
- ___initcall_start = .;
- INITCALLS
- ___initcall_end = .;
- }
- .con_initcall.init :
- {
- ___con_initcall_start = .;
- *(.con_initcall.init)
- ___con_initcall_end = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
+ . = ALIGN(16);
+ INIT_DATA_SECTION(16)
PERCPU(4)
- SECURITY_INIT
/* we have to discard exit text and such at runtime, not link time, to
* handle embedded cross-section references (alt instructions, bug
EXIT_DATA
}
- .init.ramfs :
- {
- . = ALIGN(4);
- ___initramfs_start = .;
- *(.init.ramfs)
- . = ALIGN(4);
- ___initramfs_end = .;
- }
-
__l1_lma_start = .;
- .text_l1 L1_CODE_START : AT(LOADADDR(.init.ramfs) + SIZEOF(.init.ramfs))
+ .text_l1 L1_CODE_START : AT(LOADADDR(.exit.data) + SIZEOF(.exit.data))
{
. = ALIGN(4);
__stext_l1 = .;
return ret;
}
-static struct file_operations coreb_fops = {
+static const struct file_operations coreb_fops = {
.owner = THIS_MODULE,
.ioctl = coreb_ioctl,
};
#define NUMBER_OF_PORTS 2
-static struct file_operations sync_serial_fops = {
+static const struct file_operations sync_serial_fops = {
.owner = THIS_MODULE,
.write = sync_serial_write,
.read = sync_serial_read,
extern void update_xtime_from_cmos(void);
extern int set_rtc_mmss(unsigned long nowtime);
-extern int setup_irq(int, struct irqaction *);
extern int have_rtc;
unsigned long get_ns_in_jiffie(void)
return 0;
}
-struct file_operations gpio_fops = {
+static const struct file_operations gpio_fops = {
.owner = THIS_MODULE,
.poll = gpio_poll,
.ioctl = gpio_ioctl,
static struct vm_area_struct* flush_vma;
static unsigned long flush_addr;
-extern int setup_irq(int, struct irqaction *);
-
/* Mode registers */
static unsigned long irq_regs[NR_CPUS] = {
regi_irq,
extern void update_xtime_from_cmos(void);
extern int set_rtc_mmss(unsigned long nowtime);
-extern int setup_irq(int, struct irqaction *);
extern int have_rtc;
#ifdef CONFIG_CPU_FREQ
},
};
-#define NBR_OF_PORTS sizeof(crisv32_ioports)/sizeof(struct crisv32_ioport)
+#define NBR_OF_PORTS ARRAY_SIZE(crisv32_ioports)
struct crisv32_iopin crisv32_led_net0_green;
struct crisv32_iopin crisv32_led_net0_red;
}
};
-#define NBR_OF_PORTS sizeof(crisv32_ioports)/sizeof(struct crisv32_ioport)
+#define NBR_OF_PORTS ARRAY_SIZE(crisv32_ioports)
struct crisv32_iopin crisv32_led_net0_green;
struct crisv32_iopin crisv32_led_net0_red;
/* CRIS PTE bits (see R_TLB_LO in the register description)
*
- * Bit: 31-13 12-------4 3 2 1 0
- * ________________________________________________
- * | pfn | reserved | global | valid | kernel | we |
- * |_____|__________|________|_______|________|_____|
+ * Bit: 31 30-13 12-------4 3 2 1 0
+ * _______________________________________________________
+ * | cache |pfn | reserved | global | valid | kernel | we |
+ * |_______|____|__________|________|_______|________|_____|
*
* (pfn = physical frame number)
*/
#define _PAGE_VALID (1<<2) /* page is valid */
#define _PAGE_SILENT_READ (1<<2) /* synonym */
#define _PAGE_GLOBAL (1<<3) /* global page - context is ignored */
+#define _PAGE_NO_CACHE (1<<31) /* part of the uncached memory map */
/* Bits the HW doesn't care about but the kernel uses them in SW */
/*
* CRISv32 PTE bits:
*
- * Bit: 31-13 12-5 4 3 2 1 0
- * +-----+------+--------+-------+--------+-------+---------+
- * | pfn | zero | global | valid | kernel | write | execute |
- * +-----+------+--------+-------+--------+-------+---------+
+ * Bit: 31 30-13 12-5 4 3 2 1 0
+ * +-------+-----+------+--------+-------+--------+-------+---------+
+ * | cache | pfn | zero | global | valid | kernel | write | execute |
+ * +-------+-----+------+--------+-------+--------+-------+---------+
*/
/*
#define _PAGE_VALID (1 << 3) /* Page is valid. */
#define _PAGE_SILENT_READ (1 << 3) /* Same as above. */
#define _PAGE_GLOBAL (1 << 4) /* Global page. */
+#define _PAGE_NO_CACHE (1 << 31) /* part of the uncached memory map */
+
/*
* The hardware doesn't care about these bits, but the kernel uses them in
#define __ASM_HARDIRQ_H
#include <asm/irq.h>
-#include <linux/threads.h>
-#include <linux/cache.h>
-
-typedef struct {
- unsigned int __softirq_pending;
-} ____cacheline_aligned irq_cpustat_t;
-
-#include <linux/irq_cpustat.h> /* Standard mappings for irq_cpustat_t above */
-
-void ack_bad_irq(unsigned int irq);
#define HARDIRQ_BITS 8
# error HARDIRQ_BITS is too low!
#endif
+#include <asm-generic/hardirq.h>
+
#endif /* __ASM_HARDIRQ_H */
static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
{ pte_val(pte) = (pte_val(pte) & _PAGE_CHG_MASK) | pgprot_val(newprot); return pte; }
+#define pgprot_noncached(prot) __pgprot((pgprot_val(prot) | _PAGE_NO_CACHE))
+
/* pte_val refers to a page in the 0x4xxxxxxx physical DRAM interval
* __pte_page(pte_val) refers to the "virtual" DRAM interval
#include <asm/io.h>
-void ack_bad_irq(unsigned int irq)
-{
- printk("unexpected IRQ trap at vector %02x\n", irq);
-}
-
int show_interrupts(struct seq_file *p, void *v)
{
int i = *(loff_t *) v, j;
_etext = . ; /* End of text section. */
__etext = .;
- . = ALIGN(4); /* Exception table. */
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
+ EXCEPTION_TABLE(4)
RODATA
__edata = . ; /* End of data section. */
_edata = . ;
- . = ALIGN(PAGE_SIZE); /* init_task and stack, must be aligned. */
- .data.init_task : { *(.data.init_task) }
+ INIT_TASK_DATA_SECTION(PAGE_SIZE)
. = ALIGN(PAGE_SIZE); /* Init code and data. */
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
.init.data : { INIT_DATA }
- . = ALIGN(16);
- __setup_start = .;
- .init.setup : { *(.init.setup) }
- __setup_end = .;
+ .init.setup : { INIT_SETUP(16) }
#ifdef CONFIG_ETRAX_ARCH_V32
__start___param = .;
__param : { *(__param) }
__stop___param = .;
#endif
.initcall.init : {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
+ INIT_CALLS
}
.con_initcall.init : {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
+ CON_INITCALL
}
SECURITY_INIT
PERCPU(PAGE_SIZE)
.init.ramfs : {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
+ INIT_RAM_FS
}
#endif
__init_end = .;
__data_end = . ; /* Move to _edata ? */
- __bss_start = .; /* BSS. */
- .bss : {
- *(COMMON)
- *(.bss)
- }
+ BSS_SECTION(0, 0, 0)
. = ALIGN (0x20);
_end = .;
/*
* Send us to sleep.
*/
-static int sysctl_pm_do_suspend(ctl_table *ctl, int write, struct file *filp,
+static int sysctl_pm_do_suspend(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *fpos)
{
int retval, mode;
}
-static int cmode_procctl(ctl_table *ctl, int write, struct file *filp,
+static int cmode_procctl(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *fpos)
{
int new_cmode;
if (!write)
- return proc_dointvec(ctl, write, filp, buffer, lenp, fpos);
+ return proc_dointvec(ctl, write, buffer, lenp, fpos);
new_cmode = user_atoi(buffer, *lenp);
return 0;
}
-static int p0_procctl(ctl_table *ctl, int write, struct file *filp,
+static int p0_procctl(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *fpos)
{
int new_p0;
if (!write)
- return proc_dointvec(ctl, write, filp, buffer, lenp, fpos);
+ return proc_dointvec(ctl, write, buffer, lenp, fpos);
new_p0 = user_atoi(buffer, *lenp);
return 1;
}
-static int cm_procctl(ctl_table *ctl, int write, struct file *filp,
+static int cm_procctl(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *fpos)
{
int new_cm;
if (!write)
- return proc_dointvec(ctl, write, filp, buffer, lenp, fpos);
+ return proc_dointvec(ctl, write, buffer, lenp, fpos);
new_cm = user_atoi(buffer, *lenp);
obj-y += pci-dma-nommu.o
endif
endif
+
+obj-$(CONFIG_MTD) += flash.o
--- /dev/null
+/* Flash mappings for the MB93090-MB00 motherboard
+ *
+ * Copyright (C) 2009 Red Hat, Inc. All Rights Reserved.
+ * Written by David Howells (dhowells@redhat.com)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public Licence
+ * as published by the Free Software Foundation; either version
+ * 2 of the Licence, or (at your option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#define MB93090_BOOTROM_ADDR 0xFF000000 /* Boot ROM */
+#define MB93090_BOOTROM_SIZE (2 * 1024 * 1024)
+#define MB93090_USERROM_ADDR 0xFF200000 /* User ROM */
+#define MB93090_USERROM_SIZE (2 * 1024 * 1024)
+
+/*
+ * default MTD partition table for both main flash devices, expected to be
+ * overridden by RedBoot
+ */
+static struct mtd_partition mb93090_partitions[] = {
+ {
+ .name = "Filesystem",
+ .size = MTDPART_SIZ_FULL,
+ .offset = 0,
+ }
+};
+
+/*
+ * Definition of the MB93090 Boot ROM (on the CPU card)
+ */
+static struct physmap_flash_data mb93090_bootrom_data = {
+ .width = 2,
+ .nr_parts = 2,
+ .parts = mb93090_partitions,
+};
+
+static struct resource mb93090_bootrom_resource = {
+ .start = MB93090_BOOTROM_ADDR,
+ .end = MB93090_BOOTROM_ADDR + MB93090_BOOTROM_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device mb93090_bootrom = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev.platform_data = &mb93090_bootrom_data,
+ .num_resources = 1,
+ .resource = &mb93090_bootrom_resource,
+};
+
+/*
+ * Definition of the MB93090 User ROM definition (on the motherboard)
+ */
+static struct physmap_flash_data mb93090_userrom_data = {
+ .width = 2,
+ .nr_parts = 2,
+ .parts = mb93090_partitions,
+};
+
+static struct resource mb93090_userrom_resource = {
+ .start = MB93090_USERROM_ADDR,
+ .end = MB93090_USERROM_ADDR + MB93090_USERROM_SIZE - 1,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device mb93090_userrom = {
+ .name = "physmap-flash",
+ .id = 1,
+ .dev.platform_data = &mb93090_userrom_data,
+ .num_resources = 1,
+ .resource = &mb93090_userrom_resource,
+};
+
+/*
+ * register the MB93090 flashes
+ */
+static int __init mb93090_mtd_init(void)
+{
+ platform_device_register(&mb93090_bootrom);
+ platform_device_register(&mb93090_userrom);
+ return 0;
+}
+
+module_init(mb93090_mtd_init);
#define VMLINUX_SYMBOL(_sym_) _##_sym_
#include <asm-generic/vmlinux.lds.h>
+#include <asm/page.h>
/* target memory map */
#ifdef CONFIG_H8300H_GENERIC
SCHED_TEXT
LOCK_TEXT
__etext = . ;
- . = ALIGN(16); /* Exception table */
- ___start___ex_table = .;
- *(__ex_table)
- ___stop___ex_table = .;
}
+ EXCEPTION_TABLE(16)
RODATA
#if defined(CONFIG_ROMKERNEL)
__sdata = . ;
___data_start = . ;
- . = ALIGN(0x2000) ;
- *(.data.init_task)
+ INIT_TASK_DATA(0x2000)
. = ALIGN(0x4) ;
DATA_DATA
. = ALIGN(0x4) ;
__einittext = .;
INIT_DATA
. = ALIGN(0x4) ;
+ INIT_SETUP(0x4)
___setup_start = .;
*(.init.setup)
. = ALIGN(0x4) ;
___setup_end = .;
- ___initcall_start = .;
- INITCALLS
- ___initcall_end = .;
- ___con_initcall_start = .;
- *(.con_initcall.init)
- ___con_initcall_end = .;
+ INIT_CALLS
+ CON_INITCALL
EXIT_TEXT
EXIT_DATA
-#if defined(CONFIG_BLK_DEV_INITRD)
- . = ALIGN(4);
- ___initramfs_start = .;
- *(.init.ramfs)
- ___initramfs_end = .;
-#endif
+ INIT_RAM_FS
. = ALIGN(0x4) ;
___init_end = .;
__edata = . ;
bool
config GENERIC_LOCKBREAK
- bool
- default y
- depends on SMP && PREEMPT
+ def_bool n
config RWSEM_XCHGADD_ALGORITHM
bool
}
-static struct vm_operations_struct ia32_shared_page_vm_ops = {
+static const struct vm_operations_struct ia32_shared_page_vm_ops = {
.fault = ia32_install_shared_page
};
-static struct vm_operations_struct ia32_gate_page_vm_ops = {
+static const struct vm_operations_struct ia32_gate_page_vm_ops = {
.fault = ia32_install_gate_page
};
#define ACPI_RELEASE_GLOBAL_LOCK(facs, Acq) \
((Acq) = ia64_acpi_release_global_lock(&facs->global_lock))
+#ifdef CONFIG_ACPI
#define acpi_disabled 0 /* ACPI always enabled on IA64 */
#define acpi_noirq 0 /* ACPI always enabled on IA64 */
#define acpi_pci_disabled 0 /* ACPI PCI always enabled on IA64 */
#define acpi_strict 1 /* no ACPI spec workarounds on IA64 */
+#endif
#define acpi_processor_cstate_check(x) (x) /* no idle limits on IA64 :) */
static inline void disable_acpi(void) { }
#define __raw_spin_lock_init(x) ((x)->lock = 0)
-#ifdef ASM_SUPPORTED
/*
- * Try to get the lock. If we fail to get the lock, make a non-standard call to
- * ia64_spinlock_contention(). We do not use a normal call because that would force all
- * callers of __raw_spin_lock() to be non-leaf routines. Instead, ia64_spinlock_contention() is
- * carefully coded to touch only those registers that __raw_spin_lock() marks "clobbered".
+ * Ticket locks are conceptually two parts, one indicating the current head of
+ * the queue, and the other indicating the current tail. The lock is acquired
+ * by atomically noting the tail and incrementing it by one (thus adding
+ * ourself to the queue and noting our position), then waiting until the head
+ * becomes equal to the the initial value of the tail.
+ *
+ * 63 32 31 0
+ * +----------------------------------------------------+
+ * | next_ticket_number | now_serving |
+ * +----------------------------------------------------+
*/
-#define IA64_SPINLOCK_CLOBBERS "ar.ccv", "ar.pfs", "p14", "p15", "r27", "r28", "r29", "r30", "b6", "memory"
+#define TICKET_SHIFT 32
-static inline void
-__raw_spin_lock_flags (raw_spinlock_t *lock, unsigned long flags)
+static __always_inline void __ticket_spin_lock(raw_spinlock_t *lock)
{
- register volatile unsigned int *ptr asm ("r31") = &lock->lock;
-
-#if (__GNUC__ == 3 && __GNUC_MINOR__ < 3)
-# ifdef CONFIG_ITANIUM
- /* don't use brl on Itanium... */
- asm volatile ("{\n\t"
- " mov ar.ccv = r0\n\t"
- " mov r28 = ip\n\t"
- " mov r30 = 1;;\n\t"
- "}\n\t"
- "cmpxchg4.acq r30 = [%1], r30, ar.ccv\n\t"
- "movl r29 = ia64_spinlock_contention_pre3_4;;\n\t"
- "cmp4.ne p14, p0 = r30, r0\n\t"
- "mov b6 = r29;;\n\t"
- "mov r27=%2\n\t"
- "(p14) br.cond.spnt.many b6"
- : "=r"(ptr) : "r"(ptr), "r" (flags) : IA64_SPINLOCK_CLOBBERS);
-# else
- asm volatile ("{\n\t"
- " mov ar.ccv = r0\n\t"
- " mov r28 = ip\n\t"
- " mov r30 = 1;;\n\t"
- "}\n\t"
- "cmpxchg4.acq r30 = [%1], r30, ar.ccv;;\n\t"
- "cmp4.ne p14, p0 = r30, r0\n\t"
- "mov r27=%2\n\t"
- "(p14) brl.cond.spnt.many ia64_spinlock_contention_pre3_4;;"
- : "=r"(ptr) : "r"(ptr), "r" (flags) : IA64_SPINLOCK_CLOBBERS);
-# endif /* CONFIG_MCKINLEY */
-#else
-# ifdef CONFIG_ITANIUM
- /* don't use brl on Itanium... */
- /* mis-declare, so we get the entry-point, not it's function descriptor: */
- asm volatile ("mov r30 = 1\n\t"
- "mov r27=%2\n\t"
- "mov ar.ccv = r0;;\n\t"
- "cmpxchg4.acq r30 = [%0], r30, ar.ccv\n\t"
- "movl r29 = ia64_spinlock_contention;;\n\t"
- "cmp4.ne p14, p0 = r30, r0\n\t"
- "mov b6 = r29;;\n\t"
- "(p14) br.call.spnt.many b6 = b6"
- : "=r"(ptr) : "r"(ptr), "r" (flags) : IA64_SPINLOCK_CLOBBERS);
-# else
- asm volatile ("mov r30 = 1\n\t"
- "mov r27=%2\n\t"
- "mov ar.ccv = r0;;\n\t"
- "cmpxchg4.acq r30 = [%0], r30, ar.ccv;;\n\t"
- "cmp4.ne p14, p0 = r30, r0\n\t"
- "(p14) brl.call.spnt.many b6=ia64_spinlock_contention;;"
- : "=r"(ptr) : "r"(ptr), "r" (flags) : IA64_SPINLOCK_CLOBBERS);
-# endif /* CONFIG_MCKINLEY */
-#endif
+ int *p = (int *)&lock->lock, turn, now_serving;
+
+ now_serving = *p;
+ turn = ia64_fetchadd(1, p+1, acq);
+
+ if (turn == now_serving)
+ return;
+
+ do {
+ cpu_relax();
+ } while (ACCESS_ONCE(*p) != turn);
}
-#define __raw_spin_lock(lock) __raw_spin_lock_flags(lock, 0)
+static __always_inline int __ticket_spin_trylock(raw_spinlock_t *lock)
+{
+ long tmp = ACCESS_ONCE(lock->lock), try;
-/* Unlock by doing an ordered store and releasing the cacheline with nta */
-static inline void __raw_spin_unlock(raw_spinlock_t *x) {
- barrier();
- asm volatile ("st4.rel.nta [%0] = r0\n\t" :: "r"(x));
+ if (!(((tmp >> TICKET_SHIFT) ^ tmp) & ((1L << TICKET_SHIFT) - 1))) {
+ try = tmp + (1L << TICKET_SHIFT);
+
+ return ia64_cmpxchg(acq, &lock->lock, tmp, try, sizeof (tmp)) == tmp;
+ }
+ return 0;
}
-#else /* !ASM_SUPPORTED */
-#define __raw_spin_lock_flags(lock, flags) __raw_spin_lock(lock)
-# define __raw_spin_lock(x) \
-do { \
- __u32 *ia64_spinlock_ptr = (__u32 *) (x); \
- __u64 ia64_spinlock_val; \
- ia64_spinlock_val = ia64_cmpxchg4_acq(ia64_spinlock_ptr, 1, 0); \
- if (unlikely(ia64_spinlock_val)) { \
- do { \
- while (*ia64_spinlock_ptr) \
- ia64_barrier(); \
- ia64_spinlock_val = ia64_cmpxchg4_acq(ia64_spinlock_ptr, 1, 0); \
- } while (ia64_spinlock_val); \
- } \
-} while (0)
-#define __raw_spin_unlock(x) do { barrier(); ((raw_spinlock_t *) x)->lock = 0; } while (0)
-#endif /* !ASM_SUPPORTED */
+static __always_inline void __ticket_spin_unlock(raw_spinlock_t *lock)
+{
+ int *p = (int *)&lock->lock;
+
+ (void)ia64_fetchadd(1, p, rel);
+}
+
+static inline int __ticket_spin_is_locked(raw_spinlock_t *lock)
+{
+ long tmp = ACCESS_ONCE(lock->lock);
+
+ return !!(((tmp >> TICKET_SHIFT) ^ tmp) & ((1L << TICKET_SHIFT) - 1));
+}
+
+static inline int __ticket_spin_is_contended(raw_spinlock_t *lock)
+{
+ long tmp = ACCESS_ONCE(lock->lock);
-#define __raw_spin_is_locked(x) ((x)->lock != 0)
-#define __raw_spin_trylock(x) (cmpxchg_acq(&(x)->lock, 0, 1) == 0)
-#define __raw_spin_unlock_wait(lock) \
- do { while (__raw_spin_is_locked(lock)) cpu_relax(); } while (0)
+ return (((tmp >> TICKET_SHIFT) - tmp) & ((1L << TICKET_SHIFT) - 1)) > 1;
+}
+
+static inline int __raw_spin_is_locked(raw_spinlock_t *lock)
+{
+ return __ticket_spin_is_locked(lock);
+}
+
+static inline int __raw_spin_is_contended(raw_spinlock_t *lock)
+{
+ return __ticket_spin_is_contended(lock);
+}
+#define __raw_spin_is_contended __raw_spin_is_contended
+
+static __always_inline void __raw_spin_lock(raw_spinlock_t *lock)
+{
+ __ticket_spin_lock(lock);
+}
+
+static __always_inline int __raw_spin_trylock(raw_spinlock_t *lock)
+{
+ return __ticket_spin_trylock(lock);
+}
+
+static __always_inline void __raw_spin_unlock(raw_spinlock_t *lock)
+{
+ __ticket_spin_unlock(lock);
+}
+
+static __always_inline void __raw_spin_lock_flags(raw_spinlock_t *lock,
+ unsigned long flags)
+{
+ __raw_spin_lock(lock);
+}
+
+static inline void __raw_spin_unlock_wait(raw_spinlock_t *lock)
+{
+ while (__raw_spin_is_locked(lock))
+ cpu_relax();
+}
#define __raw_read_can_lock(rw) (*(volatile int *)(rw) >= 0)
#define __raw_write_can_lock(rw) (*(volatile int *)(rw) == 0)
#endif
typedef struct {
- volatile unsigned int lock;
+ volatile unsigned long lock;
} raw_spinlock_t;
#define __RAW_SPIN_LOCK_UNLOCKED { 0 }
#endif /* CONFIG_IA64_BRL_EMU */
#ifdef CONFIG_SMP
- /*
- * This routine handles spinlock contention. It uses a non-standard calling
- * convention to avoid converting leaf routines into interior routines. Because
- * of this special convention, there are several restrictions:
- *
- * - do not use gp relative variables, this code is called from the kernel
- * and from modules, r1 is undefined.
- * - do not use stacked registers, the caller owns them.
- * - do not use the scratch stack space, the caller owns it.
- * - do not use any registers other than the ones listed below
- *
- * Inputs:
- * ar.pfs - saved CFM of caller
- * ar.ccv - 0 (and available for use)
- * r27 - flags from spin_lock_irqsave or 0. Must be preserved.
- * r28 - available for use.
- * r29 - available for use.
- * r30 - available for use.
- * r31 - address of lock, available for use.
- * b6 - return address
- * p14 - available for use.
- * p15 - used to track flag status.
- *
- * If you patch this code to use more registers, do not forget to update
- * the clobber lists for spin_lock() in arch/ia64/include/asm/spinlock.h.
- */
-
-#if (__GNUC__ == 3 && __GNUC_MINOR__ < 3)
-
-GLOBAL_ENTRY(ia64_spinlock_contention_pre3_4)
- .prologue
- .save ar.pfs, r0 // this code effectively has a zero frame size
- .save rp, r28
- .body
- nop 0
- tbit.nz p15,p0=r27,IA64_PSR_I_BIT
- .restore sp // pop existing prologue after next insn
- mov b6 = r28
- .prologue
- .save ar.pfs, r0
- .altrp b6
- .body
- ;;
-(p15) ssm psr.i // reenable interrupts if they were on
- // DavidM says that srlz.d is slow and is not required in this case
-.wait:
- // exponential backoff, kdb, lockmeter etc. go in here
- hint @pause
- ld4 r30=[r31] // don't use ld4.bias; if it's contended, we won't write the word
- nop 0
- ;;
- cmp4.ne p14,p0=r30,r0
-(p14) br.cond.sptk.few .wait
-(p15) rsm psr.i // disable interrupts if we reenabled them
- br.cond.sptk.few b6 // lock is now free, try to acquire
- .global ia64_spinlock_contention_pre3_4_end // for kernprof
-ia64_spinlock_contention_pre3_4_end:
-END(ia64_spinlock_contention_pre3_4)
-
-#else
-
-GLOBAL_ENTRY(ia64_spinlock_contention)
- .prologue
- .altrp b6
- .body
- tbit.nz p15,p0=r27,IA64_PSR_I_BIT
- ;;
-.wait:
-(p15) ssm psr.i // reenable interrupts if they were on
- // DavidM says that srlz.d is slow and is not required in this case
-.wait2:
- // exponential backoff, kdb, lockmeter etc. go in here
- hint @pause
- ld4 r30=[r31] // don't use ld4.bias; if it's contended, we won't write the word
- ;;
- cmp4.ne p14,p0=r30,r0
- mov r30 = 1
-(p14) br.cond.sptk.few .wait2
-(p15) rsm psr.i // disable interrupts if we reenabled them
- ;;
- cmpxchg4.acq r30=[r31], r30, ar.ccv
- ;;
- cmp4.ne p14,p0=r0,r30
-(p14) br.cond.sptk.few .wait
-
- br.ret.sptk.many b6 // lock is now taken
-END(ia64_spinlock_contention)
-
-#endif
#ifdef CONFIG_HOTPLUG_CPU
GLOBAL_ENTRY(ia64_jump_to_sal)
#include <asm/unwind.h>
EXPORT_SYMBOL(unw_init_running);
-#ifdef ASM_SUPPORTED
-# ifdef CONFIG_SMP
-# if (__GNUC__ == 3 && __GNUC_MINOR__ < 3)
-/*
- * This is not a normal routine and we don't want a function descriptor for it, so we use
- * a fake declaration here.
- */
-extern char ia64_spinlock_contention_pre3_4;
-EXPORT_SYMBOL(ia64_spinlock_contention_pre3_4);
-# else
-/*
- * This is not a normal routine and we don't want a function descriptor for it, so we use
- * a fake declaration here.
- */
-extern char ia64_spinlock_contention;
-EXPORT_SYMBOL(ia64_spinlock_contention);
-# endif
-# endif
-#endif
-
#if defined(CONFIG_IA64_ESI) || defined(CONFIG_IA64_ESI_MODULE)
extern void esi_call_phys (void);
EXPORT_SYMBOL_GPL(esi_call_phys);
u64 *prev_pfs_loc; /* state for WAR for old spinlock ool code */
} ia64_backtrace_t;
-#if (__GNUC__ == 3 && __GNUC_MINOR__ < 3)
-/*
- * Returns non-zero if the PC is in the spinlock contention out-of-line code
- * with non-standard calling sequence (on older compilers).
- */
-static __inline__ int in_old_ool_spinlock_code(unsigned long pc)
-{
- extern const char ia64_spinlock_contention_pre3_4[] __attribute__ ((weak));
- extern const char ia64_spinlock_contention_pre3_4_end[] __attribute__ ((weak));
- unsigned long sc_start = (unsigned long)ia64_spinlock_contention_pre3_4;
- unsigned long sc_end = (unsigned long)ia64_spinlock_contention_pre3_4_end;
- return (sc_start && sc_end && pc >= sc_start && pc < sc_end);
-}
-#else
-/* Newer spinlock code does a proper br.call and works fine with the unwinder */
-#define in_old_ool_spinlock_code(pc) 0
-#endif
-
/* Returns non-zero if the PC is in the Interrupt Vector Table */
static __inline__ int in_ivt_code(unsigned long pc)
{
*/
if (bt->prev_pfs_loc && bt->regs && bt->frame.pfs_loc == bt->prev_pfs_loc)
bt->frame.pfs_loc = &bt->regs->ar_pfs;
- bt->prev_pfs_loc = (in_old_ool_spinlock_code(bt->frame.ip) ? bt->frame.pfs_loc : NULL);
+ bt->prev_pfs_loc = NULL;
return unw_unwind(&bt->frame) == 0;
}
#define __raw_writew writew
#define __raw_writel writel
+#define ioread8 read
+#define ioread16 readw
+#define ioread32 readl
+#define iowrite8 writeb
+#define iowrite16 writew
+#define iowrite32 writel
+
#define mmiowb()
#define flush_write_buffers() do { } while (0) /* M32R_FIXME */
#ifndef _ASM_M32R_PAGE_H
#define _ASM_M32R_PAGE_H
+#include <linux/const.h>
+
/* PAGE_SHIFT determines the page size */
#define PAGE_SHIFT 12
-#define PAGE_SIZE (1UL << PAGE_SHIFT)
+#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
#ifndef __ASSEMBLY__
#define KSTK_EIP(tsk) ((tsk)->thread.lr)
#define KSTK_ESP(tsk) ((tsk)->thread.sp)
-#define THREAD_SIZE (2*PAGE_SIZE)
-
#define cpu_relax() barrier()
#endif /* _ASM_M32R_PROCESSOR_H */
#define PREEMPT_ACTIVE 0x10000000
+#define THREAD_SIZE (PAGE_SIZE << 1)
+
/*
* macros/functions for gaining access to the thread information structure
*/
#define init_thread_info (init_thread_union.thread_info)
#define init_stack (init_thread_union.stack)
-#define THREAD_SIZE (2*PAGE_SIZE)
-
/* how to get the thread information struct from C */
static inline struct thread_info *current_thread_info(void)
{
return ti->flags >> TI_FLAG_FAULT_CODE_SHIFT;
}
-#else /* !__ASSEMBLY__ */
-
-#define THREAD_SIZE 8192
-
-/* how to get the thread information struct from ASM */
-#define GET_THREAD_INFO(reg) GET_THREAD_INFO reg
- .macro GET_THREAD_INFO reg
- ldi \reg, #-THREAD_SIZE
- and \reg, sp
- .endm
-
#endif
/*
#define resume_kernel restore_all
#endif
+/* how to get the thread information struct from ASM */
+#define GET_THREAD_INFO(reg) GET_THREAD_INFO reg
+ .macro GET_THREAD_INFO reg
+ ldi \reg, #-THREAD_SIZE
+ and \reg, sp
+ .endm
+
ENTRY(ret_from_fork)
pop r0
bl schedule_tail
/*------------------------------------------------------------------------
* Stack area
*/
- .section .spi
+ .section .init.data, "aw"
ALIGN
.global spi_stack_top
.zero 1024
spi_stack_top:
- .section .spu
+ .section .init.data, "aw"
ALIGN
.global spu_stack_top
.zero 1024
EXPORT_SYMBOL(iounmap);
EXPORT_SYMBOL(kernel_thread);
-/* Networking helper routines. */
-/* Delay loops */
-EXPORT_SYMBOL(__udelay);
-EXPORT_SYMBOL(__delay);
-EXPORT_SYMBOL(__const_udelay);
-
EXPORT_SYMBOL(strncpy_from_user);
EXPORT_SYMBOL(__strncpy_from_user);
EXPORT_SYMBOL(clear_user);
#include <asm/hw_irq.h>
+#if defined(CONFIG_RTC_DRV_CMOS) || defined(CONFIG_RTC_DRV_CMOS_MODULE)
+/* this needs a better home */
+DEFINE_SPINLOCK(rtc_lock);
+
+#ifdef CONFIG_RTC_DRV_CMOS_MODULE
+EXPORT_SYMBOL(rtc_lock);
+#endif
+#endif /* pc-style 'CMOS' RTC support */
+
#ifdef CONFIG_SMP
extern void smp_local_timer_interrupt(void);
#endif
eit_vector[186] = (unsigned long)smp_call_function_interrupt;
eit_vector[187] = (unsigned long)smp_ipi_timer_interrupt;
eit_vector[188] = (unsigned long)smp_flush_cache_all_interrupt;
- eit_vector[189] = (unsigned long)smp_call_function_single_interrupt;
- eit_vector[190] = 0;
+ eit_vector[189] = 0; /* CPU_BOOT_IPI */
+ eit_vector[190] = (unsigned long)smp_call_function_single_interrupt;
eit_vector[191] = 0;
#endif
_flush_cache_copyback_all();
#include <asm-generic/vmlinux.lds.h>
#include <asm/addrspace.h>
#include <asm/page.h>
+#include <asm/thread_info.h>
OUTPUT_ARCH(m32r)
#if defined(__LITTLE_ENDIAN__)
#endif
_etext = .; /* End of text section */
- . = ALIGN(16); /* Exception table */
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
+ EXCEPTION_TABLE(16)
RODATA
-
- /* writeable */
- .data : { /* Data */
- *(.spu)
- *(.spi)
- DATA_DATA
- CONSTRUCTORS
- }
-
- . = ALIGN(4096);
- __nosave_begin = .;
- .data_nosave : { *(.data.nosave) }
- . = ALIGN(4096);
- __nosave_end = .;
-
- . = ALIGN(32);
- .data.cacheline_aligned : { *(.data.cacheline_aligned) }
-
+ RW_DATA_SECTION(32, PAGE_SIZE, THREAD_SIZE)
_edata = .; /* End of data section */
- . = ALIGN(8192); /* init_task */
- .data.init_task : { *(.data.init_task) }
-
/* will be freed after init */
- . = ALIGN(4096); /* Init code and data */
+ . = ALIGN(PAGE_SIZE); /* Init code and data */
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
- .init.data : { INIT_DATA }
- . = ALIGN(16);
- __setup_start = .;
- .init.setup : { *(.init.setup) }
- __setup_end = .;
- __initcall_start = .;
- .initcall.init : {
- INITCALLS
- }
- __initcall_end = .;
- __con_initcall_start = .;
- .con_initcall.init : { *(.con_initcall.init) }
- __con_initcall_end = .;
- SECURITY_INIT
- . = ALIGN(4);
- __alt_instructions = .;
- .altinstructions : { *(.altinstructions) }
- __alt_instructions_end = .;
- .altinstr_replacement : { *(.altinstr_replacement) }
- /* .exit.text is discard at runtime, not link time, to deal with references
- from .altinstructions and .eh_frame */
- .exit.text : { EXIT_TEXT }
- .exit.data : { EXIT_DATA }
-
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(4096);
- __initramfs_start = .;
- .init.ramfs : { *(.init.ramfs) }
- __initramfs_end = .;
-#endif
-
- PERCPU(4096)
- . = ALIGN(4096);
+ INIT_TEXT_SECTION(PAGE_SIZE)
+ INIT_DATA_SECTION(16)
+ PERCPU(PAGE_SIZE)
+ . = ALIGN(PAGE_SIZE);
__init_end = .;
/* freed after init ends here */
- __bss_start = .; /* BSS */
- .bss : { *(.bss) }
- . = ALIGN(4);
- __bss_stop = .;
+ BSS_SECTION(0, 0, 4)
_end = . ;
{
__const_udelay(nsecs * 0x00005); /* 2**32 / 1000000000 (rounded up) */
}
+
+EXPORT_SYMBOL(__delay);
+EXPORT_SYMBOL(__const_udelay);
+EXPORT_SYMBOL(__udelay);
EXPORT_SYMBOL(__ndelay);
} mem_prof_t;
static mem_prof_t mem_prof[MAX_NUMNODES];
+extern unsigned long memory_start;
+extern unsigned long memory_end;
+
static void __init mem_prof_init(void)
{
unsigned long start_pfn, holes, free_pfn;
/* Node#0 SDRAM */
mp = &mem_prof[0];
mp->start_pfn = PFN_UP(CONFIG_MEMORY_START);
- mp->pages = PFN_DOWN(CONFIG_MEMORY_SIZE);
+ mp->pages = PFN_DOWN(memory_end - memory_start);
mp->holes = 0;
mp->free_pfn = PFN_UP(__pa(_end));
; pmd = pmd_offset(pgd, address);
ld r3, @r3 ; r3: pmd data
- ldi r2, #-4096
beqz r3, 3f ; pmd_none(*pmd) ?
+ and3 r2, r3, #0xfff
+ add3 r2, r2, #-355 ; _KERNPG_TABLE(=0x163)
+ bnez r2, 3f ; pmd_bad(*pmd) ?
+ ldi r2, #-4096
+
; pte = pte_offset(pmd, address);
and r2, r3 ; r2: pte base addr
srl3 r3, r0, #10
ld r1, @r3 ; r1: pmd
beqz r1, 3f ; pmd_none(*pmd) ?
;
- and3 r1, r1, #0xeff
- ldi r4, #611 ; _KERNPG_TABLE(=611)
- bne r1, r4, 3f ; !pmd_bad(*pmd) ?
+ and3 r1, r1, #0x3ff
+ ldi r4, #0x163 ; _KERNPG_TABLE(=0x163)
+ bne r1, r4, 3f ; pmd_bad(*pmd) ?
.fillinsn
4:
#ifndef __M68K_HARDIRQ_H
#define __M68K_HARDIRQ_H
-#define HARDIRQ_BITS 8
+#include <linux/threads.h>
+#include <linux/cache.h>
+
+/* entry.S is sensitive to the offsets of these fields */
+typedef struct {
+ unsigned int __softirq_pending;
+} ____cacheline_aligned irq_cpustat_t;
-#include <asm-generic/hardirq.h>
+#include <linux/irq_cpustat.h> /* Standard mappings for irq_cpustat_t above */
+
+#define HARDIRQ_BITS 8
#endif
DEFINE(THREAD_FPSTATE, offsetof(struct thread_struct, fpstate));
/* offsets into the pt_regs */
- DEFINE(PT_D0, offsetof(struct pt_regs, d0));
- DEFINE(PT_ORIG_D0, offsetof(struct pt_regs, orig_d0));
- DEFINE(PT_D1, offsetof(struct pt_regs, d1));
- DEFINE(PT_D2, offsetof(struct pt_regs, d2));
- DEFINE(PT_D3, offsetof(struct pt_regs, d3));
- DEFINE(PT_D4, offsetof(struct pt_regs, d4));
- DEFINE(PT_D5, offsetof(struct pt_regs, d5));
- DEFINE(PT_A0, offsetof(struct pt_regs, a0));
- DEFINE(PT_A1, offsetof(struct pt_regs, a1));
- DEFINE(PT_A2, offsetof(struct pt_regs, a2));
- DEFINE(PT_PC, offsetof(struct pt_regs, pc));
- DEFINE(PT_SR, offsetof(struct pt_regs, sr));
+ DEFINE(PT_OFF_D0, offsetof(struct pt_regs, d0));
+ DEFINE(PT_OFF_ORIG_D0, offsetof(struct pt_regs, orig_d0));
+ DEFINE(PT_OFF_D1, offsetof(struct pt_regs, d1));
+ DEFINE(PT_OFF_D2, offsetof(struct pt_regs, d2));
+ DEFINE(PT_OFF_D3, offsetof(struct pt_regs, d3));
+ DEFINE(PT_OFF_D4, offsetof(struct pt_regs, d4));
+ DEFINE(PT_OFF_D5, offsetof(struct pt_regs, d5));
+ DEFINE(PT_OFF_A0, offsetof(struct pt_regs, a0));
+ DEFINE(PT_OFF_A1, offsetof(struct pt_regs, a1));
+ DEFINE(PT_OFF_A2, offsetof(struct pt_regs, a2));
+ DEFINE(PT_OFF_PC, offsetof(struct pt_regs, pc));
+ DEFINE(PT_OFF_SR, offsetof(struct pt_regs, sr));
#ifdef CONFIG_COLDFIRE
/* bitfields are a bit difficult */
- DEFINE(PT_FORMATVEC, offsetof(struct pt_regs, sr) - 2);
+ DEFINE(PT_OFF_FORMATVEC, offsetof(struct pt_regs, sr) - 2);
#else
/* bitfields are a bit difficult */
- DEFINE(PT_VECTOR, offsetof(struct pt_regs, pc) + 4);
+ DEFINE(PT_OFF_VECTOR, offsetof(struct pt_regs, pc) + 4);
#endif
/* signal defines */
ENTRY(buserr)
SAVE_ALL
moveq #-1,%d0
- movel %d0,%sp@(PT_ORIG_D0)
+ movel %d0,%sp@(PT_OFF_ORIG_D0)
movel %sp,%sp@- /* stack frame pointer argument */
jsr buserr_c
addql #4,%sp
ENTRY(trap)
SAVE_ALL
moveq #-1,%d0
- movel %d0,%sp@(PT_ORIG_D0)
+ movel %d0,%sp@(PT_OFF_ORIG_D0)
movel %sp,%sp@- /* stack frame pointer argument */
jsr trap_c
addql #4,%sp
ENTRY(dbginterrupt)
SAVE_ALL
moveq #-1,%d0
- movel %d0,%sp@(PT_ORIG_D0)
+ movel %d0,%sp@(PT_OFF_ORIG_D0)
movel %sp,%sp@- /* stack frame pointer argument */
jsr dbginterrupt_c
addql #4,%sp
totalram_pages++;
pages++;
}
- printk (KERN_NOTICE "Freeing initrd memory: %dk freed\n", pages);
+ printk (KERN_NOTICE "Freeing initrd memory: %dk freed\n", pages * (PAGE_SIZE / 1024));
}
#endif
#include <asm/mcfsim.h>
#include <asm/mcfuart.h>
#include <asm/mcfdma.h>
-#include <asm/mcfuart.h>
/***************************************************************************/
.globl inthandler7
badsys:
- movel #-ENOSYS,%sp@(PT_D0)
+ movel #-ENOSYS,%sp@(PT_OFF_D0)
jra ret_from_exception
do_trace:
- movel #-ENOSYS,%sp@(PT_D0) /* needed for strace*/
+ movel #-ENOSYS,%sp@(PT_OFF_D0) /* needed for strace*/
subql #4,%sp
SAVE_SWITCH_STACK
jbsr syscall_trace
RESTORE_SWITCH_STACK
addql #4,%sp
- movel %sp@(PT_ORIG_D0),%d1
+ movel %sp@(PT_OFF_ORIG_D0),%d1
movel #-ENOSYS,%d0
cmpl #NR_syscalls,%d1
jcc 1f
lea sys_call_table, %a0
jbsr %a0@(%d1)
-1: movel %d0,%sp@(PT_D0) /* save the return value */
+1: movel %d0,%sp@(PT_OFF_D0) /* save the return value */
subql #4,%sp /* dummy return address */
SAVE_SWITCH_STACK
jbsr syscall_trace
jbsr set_esp0
addql #4,%sp
- movel %sp@(PT_ORIG_D0),%d0
+ movel %sp@(PT_OFF_ORIG_D0),%d0
movel %sp,%d1 /* get thread_info pointer */
andl #-THREAD_SIZE,%d1
lea sys_call_table,%a0
movel %a0@(%d0), %a0
jbsr %a0@
- movel %d0,%sp@(PT_D0) /* save the return value*/
+ movel %d0,%sp@(PT_OFF_D0) /* save the return value*/
ret_from_exception:
- btst #5,%sp@(PT_SR) /* check if returning to kernel*/
+ btst #5,%sp@(PT_OFF_SR) /* check if returning to kernel*/
jeq Luser_return /* if so, skip resched, signals*/
Lkernel_return:
*/
inthandler1:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler2:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler3:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler4:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler5:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler6:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler7:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
inthandler:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and #0x3ff, %d0
movel %sp,%sp@-
2:
RESTORE_ALL
1:
- moveb %sp@(PT_SR), %d0
+ moveb %sp@(PT_OFF_SR), %d0
and #7, %d0
jhi 2b
.globl inthandler
badsys:
- movel #-ENOSYS,%sp@(PT_D0)
+ movel #-ENOSYS,%sp@(PT_OFF_D0)
jra ret_from_exception
do_trace:
- movel #-ENOSYS,%sp@(PT_D0) /* needed for strace*/
+ movel #-ENOSYS,%sp@(PT_OFF_D0) /* needed for strace*/
subql #4,%sp
SAVE_SWITCH_STACK
jbsr syscall_trace
RESTORE_SWITCH_STACK
addql #4,%sp
- movel %sp@(PT_ORIG_D0),%d1
+ movel %sp@(PT_OFF_ORIG_D0),%d1
movel #-ENOSYS,%d0
cmpl #NR_syscalls,%d1
jcc 1f
lea sys_call_table, %a0
jbsr %a0@(%d1)
-1: movel %d0,%sp@(PT_D0) /* save the return value */
+1: movel %d0,%sp@(PT_OFF_D0) /* save the return value */
subql #4,%sp /* dummy return address */
SAVE_SWITCH_STACK
jbsr syscall_trace
lea sys_call_table,%a0
movel %a0@(%d0), %a0
jbsr %a0@
- movel %d0,%sp@(PT_D0) /* save the return value*/
+ movel %d0,%sp@(PT_OFF_D0) /* save the return value*/
ret_from_exception:
- btst #5,%sp@(PT_SR) /* check if returning to kernel*/
+ btst #5,%sp@(PT_OFF_SR) /* check if returning to kernel*/
jeq Luser_return /* if so, skip resched, signals*/
Lkernel_return:
*/
inthandler:
SAVE_ALL
- movew %sp@(PT_VECTOR), %d0
+ movew %sp@(PT_OFF_VECTOR), %d0
and.l #0x3ff, %d0
lsr.l #0x02, %d0
2:
RESTORE_ALL
1:
- moveb %sp@(PT_SR), %d0
+ moveb %sp@(PT_OFF_SR), %d0
and #7, %d0
jhi 2b
/* check if we need to do software interrupts */
movel %d3,%a0
jbsr %a0@
- movel %d0,%sp@(PT_D0) /* save the return value */
+ movel %d0,%sp@(PT_OFF_D0) /* save the return value */
jra ret_from_exception
1:
- movel #-ENOSYS,%d2 /* strace needs -ENOSYS in PT_D0 */
- movel %d2,PT_D0(%sp) /* on syscall entry */
+ movel #-ENOSYS,%d2 /* strace needs -ENOSYS in PT_OFF_D0 */
+ movel %d2,PT_OFF_D0(%sp) /* on syscall entry */
subql #4,%sp
SAVE_SWITCH_STACK
jbsr syscall_trace
addql #4,%sp
movel %d3,%a0
jbsr %a0@
- movel %d0,%sp@(PT_D0) /* save the return value */
+ movel %d0,%sp@(PT_OFF_D0) /* save the return value */
subql #4,%sp /* dummy return address */
SAVE_SWITCH_STACK
jbsr syscall_trace
ret_from_exception:
move #0x2700,%sr /* disable intrs */
- btst #5,%sp@(PT_SR) /* check if returning to kernel */
+ btst #5,%sp@(PT_OFF_SR) /* check if returning to kernel */
jeq Luser_return /* if so, skip resched, signals */
#ifdef CONFIG_PREEMPT
Lreturn:
move #0x2700,%sr /* disable intrs */
movel sw_usp,%a0 /* get usp */
- movel %sp@(PT_PC),%a0@- /* copy exception program counter */
- movel %sp@(PT_FORMATVEC),%a0@-/* copy exception format/vector/sr */
+ movel %sp@(PT_OFF_PC),%a0@- /* copy exception program counter */
+ movel %sp@(PT_OFF_FORMATVEC),%a0@- /* copy exception format/vector/sr */
moveml %sp@,%d1-%d5/%a0-%a2
lea %sp@(32),%sp /* space for 8 regs */
movel %sp@+,%d0
ENTRY(inthandler)
SAVE_ALL
moveq #-1,%d0
- movel %d0,%sp@(PT_ORIG_D0)
+ movel %d0,%sp@(PT_OFF_ORIG_D0)
- movew %sp@(PT_FORMATVEC),%d0 /* put exception # in d0 */
+ movew %sp@(PT_OFF_FORMATVEC),%d0 /* put exception # in d0 */
andl #0x03fc,%d0 /* mask out vector only */
movel %sp,%sp@- /* push regs arg */
ENTRY(fasthandler)
SAVE_LOCAL
- movew %sp@(PT_FORMATVEC),%d0
+ movew %sp@(PT_OFF_FORMATVEC),%d0
andl #0x03fc,%d0 /* mask out vector only */
movel %sp,%sp@- /* push regs arg */
config MICROBLAZE
def_bool y
select HAVE_LMB
+ select USB_ARCH_HAS_EHCI
select ARCH_WANT_OPTIONAL_GPIOLIB
config SWAP
CPUFLAGS-1 += $(call cc-option,-mcpu=v$(CPU_VER))
# r31 holds current when in kernel mode
-KBUILD_KERNEL += -ffixed-r31 $(CPUFLAGS-1) $(CPUFLAGS-2)
+KBUILD_CFLAGS += -ffixed-r31 $(CPUFLAGS-1) $(CPUFLAGS-2)
LDFLAGS :=
LDFLAGS_vmlinux :=
-LIBGCC := $(shell $(CC) $(KBUILD_KERNEL) -print-libgcc-file-name)
+LIBGCC := $(shell $(CC) $(KBUILD_CFLAGS) -print-libgcc-file-name)
head-y := arch/microblaze/kernel/head.o
libs-y += arch/microblaze/lib/
boot := arch/microblaze/boot
+# Are we making a simpleImage.<boardname> target? If so, crack out the boardname
+DTB:=$(subst simpleImage.,,$(filter simpleImage.%, $(MAKECMDGOALS)))
+
+ifneq ($(DTB),)
+ core-y += $(boot)/
+endif
+
# defines filename extension depending memory management type
ifeq ($(CONFIG_MMU),)
MMU := -nommu
endif
-export MMU
+export MMU DTB
all: linux.bin
+BOOT_TARGETS = linux.bin linux.bin.gz simpleImage.%
+
archclean:
$(Q)$(MAKE) $(clean)=$(boot)
-linux.bin linux.bin.gz: vmlinux
+$(BOOT_TARGETS): vmlinux
$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
define archhelp
- echo '* linux.bin - Create raw binary'
- echo ' linux.bin.gz - Create compressed raw binary'
+ echo '* linux.bin - Create raw binary'
+ echo ' linux.bin.gz - Create compressed raw binary'
+ echo ' simpleImage.<dt> - ELF image with $(arch)/boot/dts/<dt>.dts linked in'
+ echo ' - stripped elf with fdt blob
+ echo ' simpleImage.<dt>.unstrip - full ELF image with fdt blob'
+ echo ' *_defconfig - Select default config from arch/microblaze/configs'
+ echo ''
+ echo ' Targets with <dt> embed a device tree blob inside the image'
+ echo ' These targets support board with firmware that does not'
+ echo ' support passing a device tree directly. Replace <dt> with the'
+ echo ' name of a dts file from the arch/microblaze/boot/dts/ directory'
+ echo ' (minus the .dts extension).'
endef
# arch/microblaze/boot/Makefile
#
-targets := linux.bin linux.bin.gz
+obj-y += linked_dtb.o
+
+targets := linux.bin linux.bin.gz simpleImage.%
OBJCOPYFLAGS_linux.bin := -O binary
+# Where the DTS files live
+dtstree := $(srctree)/$(src)/dts
+
+# Ensure system.dtb exists
+$(obj)/linked_dtb.o: $(obj)/system.dtb
+
+# Generate system.dtb from $(DTB).dtb
+ifneq ($(DTB),system)
+$(obj)/system.dtb: $(obj)/$(DTB).dtb
+ $(call if_changed,cp)
+endif
+
$(obj)/linux.bin: vmlinux FORCE
[ -n $(CONFIG_INITRAMFS_SOURCE) ] && [ ! -e $(CONFIG_INITRAMFS_SOURCE) ] && \
touch $(CONFIG_INITRAMFS_SOURCE) || echo "No CPIO image"
$(call if_changed,gzip)
@echo 'Kernel: $@ is ready' ' (#'`cat .version`')'
-clean-kernel += linux.bin linux.bin.gz
+quiet_cmd_cp = CP $< $@$2
+ cmd_cp = cat $< >$@$2 || (rm -f $@ && echo false)
+
+quiet_cmd_strip = STRIP $@
+ cmd_strip = $(STRIP) -K _start -K _end -K __log_buf -K _fdt_start vmlinux -o $@
+
+$(obj)/simpleImage.%: vmlinux FORCE
+ $(call if_changed,cp,.unstrip)
+ $(call if_changed,strip)
+ @echo 'Kernel: $@ is ready' ' (#'`cat .version`')'
+
+# Rule to build device tree blobs
+DTC = $(objtree)/scripts/dtc/dtc
+
+# Rule to build device tree blobs
+quiet_cmd_dtc = DTC $@
+ cmd_dtc = $(DTC) -O dtb -o $(obj)/$*.dtb -b 0 -p 1024 $(dtstree)/$*.dts
+
+$(obj)/%.dtb: $(dtstree)/%.dts FORCE
+ $(call if_changed,dtc)
+
+clean-kernel += linux.bin linux.bin.gz simpleImage.*
+
+clean-files += *.dtb
--- /dev/null
+../../platform/generic/system.dts
\ No newline at end of file
--- /dev/null
+.section __fdt_blob,"a"
+.incbin "arch/microblaze/boot/system.dtb"
+
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc6
-# Tue Aug 18 11:00:02 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 10:28:50 2009
#
CONFIG_MICROBLAZE=y
# CONFIG_SWAP is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_KS8842 is not set
+CONFIG_XILINX_EMACLITE=y
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_DISPLAY_SUPPORT is not set
# CONFIG_SOUND is not set
# CONFIG_USB_SUPPORT is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_PAGE_POISONING is not set
# CONFIG_SAMPLES is not set
# CONFIG_KMEMCHECK is not set
CONFIG_EARLY_PRINTK=y
-CONFIG_HEART_BEAT=y
+# CONFIG_HEART_BEAT is not set
CONFIG_DEBUG_BOOTMEM=y
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc6
-# Tue Aug 18 10:35:30 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 10:29:43 2009
#
CONFIG_MICROBLAZE=y
# CONFIG_SWAP is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
CONFIG_WIRELESS_OLD_REGULATORY=y
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_OF_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
#
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PHYSMAP_OF is not set
CONFIG_MTD_UCLINUX=y
# CONFIG_MTD_PLATRAM is not set
# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_KS8842 is not set
+# CONFIG_XILINX_EMACLITE is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
# CONFIG_USB_ARCH_HAS_OHCI is not set
-# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_DEBUG_LIST=y
CONFIG_DEBUG_SG=y
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_EARLY_PRINTK=y
-CONFIG_HEART_BEAT=y
+# CONFIG_HEART_BEAT is not set
# CONFIG_DEBUG_BOOTMEM is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
--- /dev/null
+#ifndef _ASM_MICROBLAZE_ASM_COMPAT_H
+#define _ASM_MICROBLAZE_ASM_COMPAT_H
+
+#include <asm/types.h>
+
+#ifdef __ASSEMBLY__
+# define stringify_in_c(...) __VA_ARGS__
+# define ASM_CONST(x) x
+#else
+/* This version of stringify will deal with commas... */
+# define __stringify_in_c(...) #__VA_ARGS__
+# define stringify_in_c(...) __stringify_in_c(__VA_ARGS__) " "
+# define __ASM_CONST(x) x##UL
+# define ASM_CONST(x) __ASM_CONST(x)
+#endif
+
+#endif /* _ASM_MICROBLAZE_ASM_COMPAT_H */
#define in_be32(a) __raw_readl((const void __iomem __force *)(a))
#define in_be16(a) __raw_readw(a)
+#define writel_be(v, a) out_be32((__force unsigned *)a, v)
+#define readl_be(a) in_be32((__force unsigned *)a)
+
/*
* Little endian
*/
+++ /dev/null
-#include <asm-generic/ipc.h>
#include <linux/pfn.h>
#include <asm/setup.h>
+#include <asm/asm-compat.h>
#include <linux/const.h>
#ifdef __KERNEL__
#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
+#define LOAD_OFFSET ASM_CONST((CONFIG_KERNEL_START-CONFIG_KERNEL_BASE_ADDR))
+
#ifndef __ASSEMBLY__
#define PAGE_UP(addr) (((addr)+((PAGE_SIZE)-1))&(~((PAGE_SIZE)-1)))
void time_init(void);
void init_IRQ(void);
void machine_early_init(const char *cmdline, unsigned int ram,
- unsigned int fdt);
+ unsigned int fdt, unsigned int msr);
void machine_restart(char *cmd);
void machine_shutdown(void);
--- /dev/null
+#ifndef __ASM_MICROBLAZE_SYSCALL_H
+#define __ASM_MICROBLAZE_SYSCALL_H
+
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <asm/ptrace.h>
+
+/* The system call number is given by the user in R12 */
+static inline long syscall_get_nr(struct task_struct *task,
+ struct pt_regs *regs)
+{
+ return regs->r12;
+}
+
+static inline void syscall_rollback(struct task_struct *task,
+ struct pt_regs *regs)
+{
+ /* TODO. */
+}
+
+static inline long syscall_get_error(struct task_struct *task,
+ struct pt_regs *regs)
+{
+ return IS_ERR_VALUE(regs->r3) ? regs->r3 : 0;
+}
+
+static inline long syscall_get_return_value(struct task_struct *task,
+ struct pt_regs *regs)
+{
+ return regs->r3;
+}
+
+static inline void syscall_set_return_value(struct task_struct *task,
+ struct pt_regs *regs,
+ int error, long val)
+{
+ if (error)
+ regs->r3 = -error;
+ else
+ regs->r3 = val;
+}
+
+static inline microblaze_reg_t microblaze_get_syscall_arg(struct pt_regs *regs,
+ unsigned int n)
+{
+ switch (n) {
+ case 5: return regs->r10;
+ case 4: return regs->r9;
+ case 3: return regs->r8;
+ case 2: return regs->r7;
+ case 1: return regs->r6;
+ case 0: return regs->r5;
+ default:
+ BUG();
+ }
+ return ~0;
+}
+
+static inline void microblaze_set_syscall_arg(struct pt_regs *regs,
+ unsigned int n,
+ unsigned long val)
+{
+ switch (n) {
+ case 5:
+ regs->r10 = val;
+ case 4:
+ regs->r9 = val;
+ case 3:
+ regs->r8 = val;
+ case 2:
+ regs->r7 = val;
+ case 1:
+ regs->r6 = val;
+ case 0:
+ regs->r5 = val;
+ default:
+ BUG();
+ }
+}
+
+static inline void syscall_get_arguments(struct task_struct *task,
+ struct pt_regs *regs,
+ unsigned int i, unsigned int n,
+ unsigned long *args)
+{
+ while (n--)
+ *args++ = microblaze_get_syscall_arg(regs, i++);
+}
+
+static inline void syscall_set_arguments(struct task_struct *task,
+ struct pt_regs *regs,
+ unsigned int i, unsigned int n,
+ const unsigned long *args)
+{
+ while (n--)
+ microblaze_set_syscall_arg(regs, i++, *args++);
+}
+
+#endif /* __ASM_MICROBLAZE_SYSCALL_H */
{"7.10.d", 0x0b},
{"7.20.a", 0x0c},
{"7.20.b", 0x0d},
+ {"7.20.c", 0x0e},
/* FIXME There is no keycode defined in MBV for these versions */
{"2.10.a", 0x10},
{"3.00.a", 0x20},
{"spartan3a", 0xa},
{"spartan3an", 0xb},
{"spartan3adsp", 0xc},
+ {"spartan6", 0xd},
+ {"virtex6", 0xe},
/* FIXME There is no key code defined for spartan2 */
{"spartan2", 0xf0},
{NULL, 0},
swi r12, r1, PTO+PT_R0;
tovirt(r1,r1)
- la r15, r0, ret_from_trap-8
/* where the trap should return need -8 to adjust for rtsd r15, 8*/
/* Jump to the appropriate function for the system call number in r12
* (r12 is not preserved), or return an error if r12 is not valid. The LP
* register should point to the location where
* the called function should return. [note that MAKE_SYS_CALL uses label 1] */
- /* See if the system call number is valid. */
+
+ # Step into virtual mode.
+ set_vms;
+ addik r11, r0, 3f
+ rtid r11, 0
+ nop
+3:
+ add r11, r0, CURRENT_TASK /* Get current task ptr into r11 */
+ lwi r11, r11, TS_THREAD_INFO /* get thread info */
+ lwi r11, r11, TI_FLAGS /* get flags in thread info */
+ andi r11, r11, _TIF_WORK_SYSCALL_MASK
+ beqi r11, 4f
+
+ addik r3, r0, -ENOSYS
+ swi r3, r1, PTO + PT_R3
+ brlid r15, do_syscall_trace_enter
+ addik r5, r1, PTO + PT_R0
+
+ # do_syscall_trace_enter returns the new syscall nr.
+ addk r12, r0, r3
+ lwi r5, r1, PTO+PT_R5;
+ lwi r6, r1, PTO+PT_R6;
+ lwi r7, r1, PTO+PT_R7;
+ lwi r8, r1, PTO+PT_R8;
+ lwi r9, r1, PTO+PT_R9;
+ lwi r10, r1, PTO+PT_R10;
+4:
+/* Jump to the appropriate function for the system call number in r12
+ * (r12 is not preserved), or return an error if r12 is not valid.
+ * The LP register should point to the location where the called function
+ * should return. [note that MAKE_SYS_CALL uses label 1] */
+ /* See if the system call number is valid */
addi r11, r12, -__NR_syscalls;
- bgei r11,1f;
+ bgei r11,5f;
/* Figure out which function to use for this system call. */
/* Note Microblaze barrel shift is optional, so don't rely on it */
add r12, r12, r12; /* convert num -> ptr */
add r12, r12, r12;
/* Trac syscalls and stored them to r0_ram */
- lwi r3, r12, 0x400 + TOPHYS(r0_ram)
+ lwi r3, r12, 0x400 + r0_ram
addi r3, r3, 1
- swi r3, r12, 0x400 + TOPHYS(r0_ram)
+ swi r3, r12, 0x400 + r0_ram
+
+ # Find and jump into the syscall handler.
+ lwi r12, r12, sys_call_table
+ /* where the trap should return need -8 to adjust for rtsd r15, 8 */
+ la r15, r0, ret_from_trap-8
+ bra r12
- lwi r12, r12, TOPHYS(sys_call_table); /* Function ptr */
- /* Make the system call. to r12*/
- set_vms;
- rtid r12, 0;
- nop;
/* The syscall number is invalid, return an error. */
-1: VM_ON; /* RETURN() expects virtual mode*/
+5:
addi r3, r0, -ENOSYS;
rtsd r15,8; /* looks like a normal subroutine return */
or r0, r0, r0
-/* Entry point used to return from a syscall/trap. */
+/* Entry point used to return from a syscall/trap */
/* We re-enable BIP bit before state restore */
C_ENTRY(ret_from_trap):
set_bip; /* Ints masked for state restore*/
/* See if returning to kernel mode, if so, skip resched &c. */
bnei r11, 2f;
+ /* We're returning to user mode, so check for various conditions that
+ * trigger rescheduling. */
+ # FIXME: Restructure all these flag checks.
+ add r11, r0, CURRENT_TASK; /* Get current task ptr into r11 */
+ lwi r11, r11, TS_THREAD_INFO; /* get thread info */
+ lwi r11, r11, TI_FLAGS; /* get flags in thread info */
+ andi r11, r11, _TIF_WORK_SYSCALL_MASK
+ beqi r11, 1f
+
+ swi r3, r1, PTO + PT_R3
+ swi r4, r1, PTO + PT_R4
+ brlid r15, do_syscall_trace_leave
+ addik r5, r1, PTO + PT_R0
+ lwi r3, r1, PTO + PT_R3
+ lwi r4, r1, PTO + PT_R4
+1:
+
/* We're returning to user mode, so check for various conditions that
* trigger rescheduling. */
/* Get current task ptr into r11 */
#endif
#if 0
- printk(KERN_WARNING "Exception %02x in %s mode, FSR=%08x PC=%08x ESR=%08x\n",
+ printk(KERN_WARNING "Exception %02x in %s mode, FSR=%08x PC=%08x " \
+ "ESR=%08x\n",
type, user_mode(regs) ? "user" : "kernel", fsr,
(unsigned int) regs->pc, (unsigned int) regs->esr);
#endif
switch (type & 0x1F) {
case MICROBLAZE_ILL_OPCODE_EXCEPTION:
if (user_mode(regs)) {
- printk(KERN_WARNING "Illegal opcode exception in user mode.\n");
+ pr_debug(KERN_WARNING "Illegal opcode exception " \
+ "in user mode.\n");
_exception(SIGILL, regs, ILL_ILLOPC, addr);
return;
}
- printk(KERN_WARNING "Illegal opcode exception in kernel mode.\n");
+ printk(KERN_WARNING "Illegal opcode exception " \
+ "in kernel mode.\n");
die("opcode exception", regs, SIGBUS);
break;
case MICROBLAZE_IBUS_EXCEPTION:
if (user_mode(regs)) {
- printk(KERN_WARNING "Instruction bus error exception in user mode.\n");
+ pr_debug(KERN_WARNING "Instruction bus error " \
+ "exception in user mode.\n");
_exception(SIGBUS, regs, BUS_ADRERR, addr);
return;
}
- printk(KERN_WARNING "Instruction bus error exception in kernel mode.\n");
+ printk(KERN_WARNING "Instruction bus error exception " \
+ "in kernel mode.\n");
die("bus exception", regs, SIGBUS);
break;
case MICROBLAZE_DBUS_EXCEPTION:
if (user_mode(regs)) {
- printk(KERN_WARNING "Data bus error exception in user mode.\n");
+ pr_debug(KERN_WARNING "Data bus error exception " \
+ "in user mode.\n");
_exception(SIGBUS, regs, BUS_ADRERR, addr);
return;
}
- printk(KERN_WARNING "Data bus error exception in kernel mode.\n");
+ printk(KERN_WARNING "Data bus error exception " \
+ "in kernel mode.\n");
die("bus exception", regs, SIGBUS);
break;
case MICROBLAZE_DIV_ZERO_EXCEPTION:
if (user_mode(regs)) {
- printk(KERN_WARNING "Divide by zero exception in user mode\n");
- _exception(SIGILL, regs, ILL_ILLOPC, addr);
+ pr_debug(KERN_WARNING "Divide by zero exception " \
+ "in user mode\n");
+ _exception(SIGILL, regs, FPE_INTDIV, addr);
return;
}
- printk(KERN_WARNING "Divide by zero exception in kernel mode.\n");
+ printk(KERN_WARNING "Divide by zero exception " \
+ "in kernel mode.\n");
die("Divide by exception", regs, SIGBUS);
break;
case MICROBLAZE_FPU_EXCEPTION:
- printk(KERN_WARNING "FPU exception\n");
+ pr_debug(KERN_WARNING "FPU exception\n");
/* IEEE FP exception */
/* I removed fsr variable and use code var for storing fsr */
if (fsr & FSR_IO)
#ifdef CONFIG_MMU
case MICROBLAZE_PRIVILEGED_EXCEPTION:
- printk(KERN_WARNING "Privileged exception\n");
+ pr_debug(KERN_WARNING "Privileged exception\n");
/* "brk r0,r0" - used as debug breakpoint */
if (get_user(code, (unsigned long *)regs->pc) == 0
&& code == 0x980c0000) {
mfs r1, rmsr
andi r1, r1, ~2
mts rmsr, r1
+/*
+ * Here is checking mechanism which check if Microblaze has msr instructions
+ * We load msr and compare it with previous r1 value - if is the same,
+ * msr instructions works if not - cpu don't have them.
+ */
+ /* r8=0 - I have msr instr, 1 - I don't have them */
+ rsubi r0, r0, 1 /* set the carry bit */
+ msrclr r0, 0x4 /* try to clear it */
+ /* read the carry bit, r8 will be '0' if msrclr exists */
+ addik r8, r0, 0
/* r7 may point to an FDT, or there may be one linked in.
if it's in r7, we've got to save it away ASAP.
* Please see $(ARCH)/mach-$(SUBARCH)/setup.c for
* the function.
*/
- la r8, r0, machine_early_init
- brald r15, r8
+ la r9, r0, machine_early_init
+ brald r15, r9
nop
#ifndef CONFIG_MMU
#define NUM_TO_REG(num) r ## num
#ifdef CONFIG_MMU
-/* FIXME you can't change first load of MSR because there is
- * hardcoded jump bri 4 */
#define RESTORE_STATE \
+ lwi r5, r1, 0; \
+ mts rmsr, r5; \
+ nop; \
lwi r3, r1, PT_R3; \
lwi r4, r1, PT_R4; \
lwi r5, r1, PT_R5; \
lwi r31, r0, TOPHYS(PER_CPU(CURRENT_SAVE)) /* get saved current */
#endif
+ mfs r5, rmsr;
+ nop
+ swi r5, r1, 0;
mfs r3, resr
nop
mfs r4, rear;
addk r8, r17, r0; /* Load exception address */
bralid r15, full_exception; /* Branch to the handler */
nop;
+ mts r0, rfsr; /* Clear sticky fsr */
+ nop
/*
* Trigger execution of the signal handler by enabling
regs->pc = pc;
regs->r1 = usp;
regs->pt_mode = 0;
+ regs->msr |= MSR_UMS;
}
#ifdef CONFIG_MMU
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/signal.h>
+#include <linux/elf.h>
+#include <linux/audit.h>
+#include <linux/seccomp.h>
+#include <linux/tracehook.h>
#include <linux/errno.h>
#include <asm/processor.h>
return rval;
}
+asmlinkage long do_syscall_trace_enter(struct pt_regs *regs)
+{
+ long ret = 0;
+
+ secure_computing(regs->r12);
+
+ if (test_thread_flag(TIF_SYSCALL_TRACE) &&
+ tracehook_report_syscall_entry(regs))
+ /*
+ * Tracing decided this syscall should not happen.
+ * We'll return a bogus call number to get an ENOSYS
+ * error, but leave the original number in regs->regs[0].
+ */
+ ret = -1L;
+
+ if (unlikely(current->audit_context))
+ audit_syscall_entry(EM_XILINX_MICROBLAZE, regs->r12,
+ regs->r5, regs->r6,
+ regs->r7, regs->r8);
+
+ return ret ?: regs->r12;
+}
+
+asmlinkage void do_syscall_trace_leave(struct pt_regs *regs)
+{
+ int step;
+
+ if (unlikely(current->audit_context))
+ audit_syscall_exit(AUDITSC_RESULT(regs->r3), regs->r3);
+
+ step = test_thread_flag(TIF_SINGLESTEP);
+ if (step || test_thread_flag(TIF_SYSCALL_TRACE))
+ tracehook_report_syscall_exit(regs, step);
+}
+
+#if 0
+static asmlinkage void syscall_trace(void)
+{
+ if (!test_thread_flag(TIF_SYSCALL_TRACE))
+ return;
+ if (!(current->ptrace & PT_PTRACED))
+ return;
+ /* The 0x80 provides a way for the tracing parent to distinguish
+ between a syscall stop and SIGTRAP delivery */
+ ptrace_notify(SIGTRAP | ((current->ptrace & PT_TRACESYSGOOD)
+ ? 0x80 : 0));
+ /*
+ * this isn't the same as continuing with a signal, but it will do
+ * for normal use. strace only continues with a signal if the
+ * stopping signal is not SIGTRAP. -brl
+ */
+ if (current->exit_code) {
+ send_sig(current->exit_code, current, 1);
+ current->exit_code = 0;
+ }
+}
+#endif
+
void ptrace_disable(struct task_struct *child)
{
/* nothing to do */
#endif /* CONFIG_MTD_UCLINUX_EBSS */
void __init machine_early_init(const char *cmdline, unsigned int ram,
- unsigned int fdt)
+ unsigned int fdt, unsigned int msr)
{
unsigned long *src, *dst = (unsigned long *)0x0;
early_printk("New klimit: 0x%08x\n", (unsigned)klimit);
#endif
+#if CONFIG_XILINX_MICROBLAZE0_USE_MSR_INSTR
+ if (msr)
+ early_printk("!!!Your kernel has setup MSR instruction but "
+ "CPU don't have it %d\n", msr);
+#else
+ if (!msr)
+ early_printk("!!!Your kernel not setup MSR instruction but "
+ "CPU have it %d\n", msr);
+#endif
+
for (src = __ivt_start; src < __ivt_end; src++, dst++)
*dst = *src;
OUTPUT_ARCH(microblaze)
ENTRY(_start)
+#include <asm/page.h>
#include <asm-generic/vmlinux.lds.h>
+#include <asm/thread_info.h>
jiffies = jiffies_64 + 4;
SECTIONS {
. = CONFIG_KERNEL_START;
- .text : {
+ _start = CONFIG_KERNEL_BASE_ADDR;
+ .text : AT(ADDR(.text) - LOAD_OFFSET) {
_text = . ;
_stext = . ;
*(.text .text.*)
}
. = ALIGN (4) ;
- _fdt_start = . ; /* place for fdt blob */
- . = . + 0x4000;
- _fdt_end = . ;
+ __fdt_blob : AT(ADDR(__fdt_blob) - LOAD_OFFSET) {
+ _fdt_start = . ; /* place for fdt blob */
+ *(__fdt_blob) ; /* Any link-placed DTB */
+ . = _fdt_start + 0x4000; /* Pad up to 16kbyte */
+ _fdt_end = . ;
+ }
. = ALIGN(16);
RODATA
- . = ALIGN(16);
- __ex_table : {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
+ EXCEPTION_TABLE(16)
/*
* sdata2 section can go anywhere, but must be word aligned
* and SDA2_BASE must point to the middle of it
*/
- .sdata2 : {
+ .sdata2 : AT(ADDR(.sdata2) - LOAD_OFFSET) {
_ssrw = .;
. = ALIGN(4096); /* page aligned when MMU used - origin 0x8 */
*(.sdata2)
}
_sdata = . ;
- .data ALIGN (4096) : { /* page aligned when MMU used - origin 0x4 */
- DATA_DATA
- CONSTRUCTORS
- }
- . = ALIGN(32);
- .data.cacheline_aligned : { *(.data.cacheline_aligned) }
+ RW_DATA_SECTION(32, PAGE_SIZE, THREAD_SIZE)
_edata = . ;
/* Reserve some low RAM for r0 based memory references */
r0_ram = . ;
. = . + 4096; /* a page should be enough */
- /* The initial task */
- . = ALIGN(8192);
- .data.init_task : { *(.data.init_task) }
-
/* Under the microblaze ABI, .sdata and .sbss must be contiguous */
. = ALIGN(8);
- .sdata : {
+ .sdata : AT(ADDR(.sdata) - LOAD_OFFSET) {
_ssro = .;
*(.sdata)
}
- .sbss : {
+ .sbss : AT(ADDR(.sbss) - LOAD_OFFSET) {
_ssbss = .;
*(.sbss)
_esbss = .;
__init_begin = .;
- . = ALIGN(4096);
- .init.text : {
- _sinittext = . ;
- INIT_TEXT
- _einittext = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
- .init.data : {
+ .init.data : AT(ADDR(.init.data) - LOAD_OFFSET) {
INIT_DATA
}
. = ALIGN(4);
- .init.ivt : {
+ .init.ivt : AT(ADDR(.init.ivt) - LOAD_OFFSET) {
__ivt_start = .;
*(.init.ivt)
__ivt_end = .;
}
- .init.setup : {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
+ .init.setup : AT(ADDR(.init.setup) - LOAD_OFFSET) {
+ INIT_SETUP(0)
}
- .initcall.init : {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
+ .initcall.init : AT(ADDR(.initcall.init) - LOAD_OFFSET ) {
+ INIT_CALLS
}
- .con_initcall.init : {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
+ .con_initcall.init : AT(ADDR(.con_initcall.init) - LOAD_OFFSET) {
+ CON_INITCALL
}
SECURITY_INIT
__init_end_before_initramfs = .;
- .init.ramfs ALIGN(4096) : {
+ .init.ramfs ALIGN(4096) : AT(ADDR(.init.ramfs) - LOAD_OFFSET) {
__initramfs_start = .;
*(.init.ramfs)
__initramfs_end = .;
}
__init_end = .;
- .bss ALIGN (4096) : { /* page aligned when MMU used */
+ .bss ALIGN (4096) : AT(ADDR(.bss) - LOAD_OFFSET) {
+ /* page aligned when MMU used */
__bss_start = . ;
*(.bss*)
*(COMMON)
totalram_pages++;
pages++;
}
- printk(KERN_NOTICE "Freeing initrd memory: %dk freed\n", pages);
+ printk(KERN_NOTICE "Freeing initrd memory: %dk freed\n",
+ (int)(pages * (PAGE_SIZE / 1024)));
}
#endif
#define DBDEV_TAB_SIZE ARRAY_SIZE(dbdev_tab)
#ifdef CONFIG_PM
-static u32 au1xxx_dbdma_pm_regs[NUM_DBDMA_CHANS + 1][8];
+static u32 au1xxx_dbdma_pm_regs[NUM_DBDMA_CHANS + 1][6];
#endif
au1xxx_dbdma_pm_regs[0][3] = au_readl(addr + 0x0c);
/* save channel configurations */
- for (i = 1, addr = DDMA_CHANNEL_BASE; i < NUM_DBDMA_CHANS; i++) {
+ for (i = 1, addr = DDMA_CHANNEL_BASE; i <= NUM_DBDMA_CHANS; i++) {
au1xxx_dbdma_pm_regs[i][0] = au_readl(addr + 0x00);
au1xxx_dbdma_pm_regs[i][1] = au_readl(addr + 0x04);
au1xxx_dbdma_pm_regs[i][2] = au_readl(addr + 0x08);
au1xxx_dbdma_pm_regs[i][3] = au_readl(addr + 0x0c);
au1xxx_dbdma_pm_regs[i][4] = au_readl(addr + 0x10);
au1xxx_dbdma_pm_regs[i][5] = au_readl(addr + 0x14);
- au1xxx_dbdma_pm_regs[i][6] = au_readl(addr + 0x18);
/* halt channel */
au_writel(au1xxx_dbdma_pm_regs[i][0] & ~1, addr + 0x00);
au_writel(au1xxx_dbdma_pm_regs[0][3], addr + 0x0c);
/* restore channel configurations */
- for (i = 1, addr = DDMA_CHANNEL_BASE; i < NUM_DBDMA_CHANS; i++) {
+ for (i = 1, addr = DDMA_CHANNEL_BASE; i <= NUM_DBDMA_CHANS; i++) {
au_writel(au1xxx_dbdma_pm_regs[i][0], addr + 0x00);
au_writel(au1xxx_dbdma_pm_regs[i][1], addr + 0x04);
au_writel(au1xxx_dbdma_pm_regs[i][2], addr + 0x08);
au_writel(au1xxx_dbdma_pm_regs[i][3], addr + 0x0c);
au_writel(au1xxx_dbdma_pm_regs[i][4], addr + 0x10);
au_writel(au1xxx_dbdma_pm_regs[i][5], addr + 0x14);
- au_writel(au1xxx_dbdma_pm_regs[i][6], addr + 0x18);
au_sync();
addr += 0x100; /* next channel base */
}
{
int ret;
- lock_kernel();
ret = request_irq(iodev_irq, iodev_irqhdl, IRQF_DISABLED,
iodev_name, &miscdev);
- unlock_kernel();
return ret;
}
obj-y += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
- dev-dsp.o dev-enet.o
+ dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o
obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
obj-y += boards/
#include <bcm63xx_cpu.h>
#include <bcm63xx_regs.h>
#include <bcm63xx_io.h>
-#include <bcm63xx_board.h>
#include <bcm63xx_dev_pci.h>
#include <bcm63xx_dev_enet.h>
#include <bcm63xx_dev_dsp.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_dev_uart.h>
#include <board_bcm963xx.h>
#define PFX "board_bcm963xx: "
{
u32 val;
+ bcm63xx_uart_register();
+
+ if (board.has_pccard)
+ bcm63xx_pcmcia_register();
+
if (board.has_enet0 &&
!board_get_mac_address(board.enet0.mac_addr))
bcm63xx_enet_register(0, &board.enet0);
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cs.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static struct resource pcmcia_resources[] = {
+ /* pcmcia registers */
+ {
+ /* start & end filled at runtime */
+ .flags = IORESOURCE_MEM,
+ },
+
+ /* pcmcia memory zone resources */
+ {
+ .start = BCM_PCMCIA_COMMON_BASE_PA,
+ .end = BCM_PCMCIA_COMMON_END_PA,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = BCM_PCMCIA_ATTR_BASE_PA,
+ .end = BCM_PCMCIA_ATTR_END_PA,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = BCM_PCMCIA_IO_BASE_PA,
+ .end = BCM_PCMCIA_IO_END_PA,
+ .flags = IORESOURCE_MEM,
+ },
+
+ /* PCMCIA irq */
+ {
+ /* start filled at runtime */
+ .flags = IORESOURCE_IRQ,
+ },
+
+ /* declare PCMCIA IO resource also */
+ {
+ .start = BCM_PCMCIA_IO_BASE_PA,
+ .end = BCM_PCMCIA_IO_END_PA,
+ .flags = IORESOURCE_IO,
+ },
+};
+
+static struct bcm63xx_pcmcia_platform_data pd;
+
+static struct platform_device bcm63xx_pcmcia_device = {
+ .name = "bcm63xx_pcmcia",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(pcmcia_resources),
+ .resource = pcmcia_resources,
+ .dev = {
+ .platform_data = &pd,
+ },
+};
+
+static int __init config_pcmcia_cs(unsigned int cs,
+ u32 base, unsigned int size)
+{
+ int ret;
+
+ ret = bcm63xx_set_cs_status(cs, 0);
+ if (!ret)
+ ret = bcm63xx_set_cs_base(cs, base, size);
+ if (!ret)
+ ret = bcm63xx_set_cs_status(cs, 1);
+ return ret;
+}
+
+static const __initdata struct {
+ unsigned int cs;
+ unsigned int base;
+ unsigned int size;
+} pcmcia_cs[3] = {
+ {
+ .cs = MPI_CS_PCMCIA_COMMON,
+ .base = BCM_PCMCIA_COMMON_BASE_PA,
+ .size = BCM_PCMCIA_COMMON_SIZE
+ },
+ {
+ .cs = MPI_CS_PCMCIA_ATTR,
+ .base = BCM_PCMCIA_ATTR_BASE_PA,
+ .size = BCM_PCMCIA_ATTR_SIZE
+ },
+ {
+ .cs = MPI_CS_PCMCIA_IO,
+ .base = BCM_PCMCIA_IO_BASE_PA,
+ .size = BCM_PCMCIA_IO_SIZE
+ },
+};
+
+int __init bcm63xx_pcmcia_register(void)
+{
+ int ret, i;
+
+ if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
+ return 0;
+
+ /* use correct pcmcia ready gpio depending on processor */
+ switch (bcm63xx_get_cpu_id()) {
+ case BCM6348_CPU_ID:
+ pd.ready_gpio = 22;
+ break;
+
+ case BCM6358_CPU_ID:
+ pd.ready_gpio = 18;
+ break;
+
+ default:
+ return -ENODEV;
+ }
+
+ pcmcia_resources[0].start = bcm63xx_regset_address(RSET_PCMCIA);
+ pcmcia_resources[0].end = pcmcia_resources[0].start +
+ RSET_PCMCIA_SIZE - 1;
+ pcmcia_resources[4].start = bcm63xx_get_irq_number(IRQ_PCMCIA);
+
+ /* configure pcmcia chip selects */
+ for (i = 0; i < 3; i++) {
+ ret = config_pcmcia_cs(pcmcia_cs[i].cs,
+ pcmcia_cs[i].base,
+ pcmcia_cs[i].size);
+ if (ret)
+ goto out_err;
+ }
+
+ return platform_device_register(&bcm63xx_pcmcia_device);
+
+out_err:
+ printk(KERN_ERR "unable to set pcmcia chip select\n");
+ return ret;
+}
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_uart.h>
+
+static struct resource uart_resources[] = {
+ {
+ .start = -1, /* filled at runtime */
+ .end = -1, /* filled at runtime */
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = -1, /* filled at runtime */
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bcm63xx_uart_device = {
+ .name = "bcm63xx_uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(uart_resources),
+ .resource = uart_resources,
+};
+
+int __init bcm63xx_uart_register(void)
+{
+ uart_resources[0].start = bcm63xx_regset_address(RSET_UART0);
+ uart_resources[0].end = uart_resources[0].start;
+ uart_resources[0].end += RSET_UART_SIZE - 1;
+ uart_resources[1].start = bcm63xx_get_irq_number(IRQ_UART0);
+ return platform_device_register(&bcm63xx_uart_device);
+}
--- /dev/null
+#ifndef BCM63XX_DEV_PCMCIA_H_
+#define BCM63XX_DEV_PCMCIA_H_
+
+/*
+ * PCMCIA driver platform data
+ */
+struct bcm63xx_pcmcia_platform_data {
+ unsigned int ready_gpio;
+};
+
+int bcm63xx_pcmcia_register(void);
+
+#endif /* BCM63XX_DEV_PCMCIA_H_ */
--- /dev/null
+#ifndef BCM63XX_DEV_UART_H_
+#define BCM63XX_DEV_UART_H_
+
+int bcm63xx_uart_register(void);
+
+#endif /* BCM63XX_DEV_UART_H_ */
extern asmlinkage void smp_call_function_interrupt(void);
-extern void arch_send_call_function_single_ipi(int cpu);
-extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
+static inline void arch_send_call_function_single_ipi(int cpu)
+{
+ extern struct plat_smp_ops *mp_ops; /* private */
+
+ mp_ops->send_ipi_mask(&cpumask_of_cpu(cpu), SMP_CALL_FUNCTION);
+}
+
+static inline void arch_send_call_function_ipi_mask(const struct cpumask *mask)
+{
+ extern struct plat_smp_ops *mp_ops; /* private */
+
+ mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
+}
#endif /* __ASM_SMP_H */
#if defined(__MIPSEB__)
# include <linux/unaligned/be_struct.h>
# include <linux/unaligned/le_byteshift.h>
-# include <linux/unaligned/generic.h>
# define get_unaligned __get_unaligned_be
# define put_unaligned __put_unaligned_be
#elif defined(__MIPSEL__)
# include <linux/unaligned/le_struct.h>
# include <linux/unaligned/be_byteshift.h>
-# include <linux/unaligned/generic.h>
# define get_unaligned __get_unaligned_le
# define put_unaligned __put_unaligned_le
#else
# error "MIPS, but neither __MIPSEB__, nor __MIPSEL__???"
#endif
+# include <linux/unaligned/generic.h>
+
#endif /* _ASM_MIPS_UNALIGNED_H */
# Makefile for the Linux/MIPS kernel.
#
+CPPFLAGS_vmlinux.lds := $(KBUILD_CFLAGS)
+
extra-y := head.o init_task.o vmlinux.lds
obj-y += cpu-probe.o branch.o entry.o genex.o irq.o process.o \
}
-static void sp_setfsuidgid( uid_t uid, gid_t gid)
+static int sp_setfsuidgid(uid_t uid, gid_t gid)
{
- current->cred->fsuid = uid;
- current->cred->fsgid = gid;
+ struct cred *new;
- key_fsuid_changed(current);
- key_fsgid_changed(current);
+ new = prepare_creds();
+ if (!new)
+ return -ENOMEM;
+
+ new->fsuid = uid;
+ new->fsgid = gid;
+
+ commit_creds(new);
+
+ return 0;
}
/*
mm_segment_t old_fs;
struct timeval tv;
struct timezone tz;
- int cmd;
+ int err, cmd;
char *vcwd;
int size;
/* Run the syscall at the privilege of the user who loaded the
SP program */
- if (vpe_getuid(tclimit))
- sp_setfsuidgid(vpe_getuid(tclimit), vpe_getgid(tclimit));
+ if (vpe_getuid(tclimit)) {
+ err = sp_setfsuidgid(vpe_getuid(tclimit), vpe_getgid(tclimit));
+ if (!err)
+ pr_err("Change of creds failed\n");
+ }
switch (sc.cmd) {
/* needs the flags argument translating from SDE kit to
break;
} /* switch */
- if (vpe_getuid(tclimit))
- sp_setfsuidgid( 0, 0);
+ if (vpe_getuid(tclimit)) {
+ err = sp_setfsuidgid(0, 0);
+ if (!err)
+ pr_err("restoring old creds failed\n");
+ }
old_fs = get_fs();
set_fs(KERNEL_DS);
*/
static irqreturn_t rtlx_interrupt(int irq, void *dev_id)
{
+ unsigned int vpeflags;
+ unsigned long flags;
int i;
- unsigned int flags, vpeflags;
/* Ought not to be strictly necessary for SMTC builds */
local_irq_save(flags);
static int file_open(struct inode *inode, struct file *filp)
{
- int minor = iminor(inode);
- int err;
-
- lock_kernel();
- err = rtlx_open(minor, (filp->f_flags & O_NONBLOCK) ? 0 : 1);
- unlock_kernel();
- return err;
+ return rtlx_open(iminor(inode), (filp->f_flags & O_NONBLOCK) ? 0 : 1);
}
static int file_release(struct inode *inode, struct file *filp)
{
- int minor = iminor(inode);
-
- return rtlx_release(minor);
+ return rtlx_release(iminor(inode));
}
static unsigned int file_poll(struct file *file, poll_table * wait)
#include <linux/cpumask.h>
#include <linux/cpu.h>
#include <linux/err.h>
-#include <linux/smp.h>
#include <asm/atomic.h>
#include <asm/cpu.h>
cpu_idle();
}
-void arch_send_call_function_ipi_mask(const struct cpumask *mask)
-{
- mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
-}
-
-/*
- * We reuse the same vector for the single IPI
- */
-void arch_send_call_function_single_ipi(int cpu)
-{
- mp_ops->send_ipi_mask(cpumask_of_cpu(cpu), SMP_CALL_FUNCTION);
-}
-
/*
* Call into both interrupt handlers, as we share the IPI for them
*/
static struct irqaction irq_ipi = {
.handler = ipi_interrupt,
- .flags = IRQF_DISABLED,
- .name = "SMTC_IPI",
- .flags = IRQF_PERCPU
+ .flags = IRQF_DISABLED | IRQF_PERCPU,
+ .name = "SMTC_IPI"
};
static void setup_cross_vpe_interrupts(unsigned int nvpe)
note PT_NOTE FLAGS(4); /* R__ */
}
-ifdef CONFIG_32BIT
- ifdef CONFIG_CPU_LITTLE_ENDIAN
+#ifdef CONFIG_32BIT
+ #ifdef CONFIG_CPU_LITTLE_ENDIAN
jiffies = jiffies_64;
- else
+ #else
jiffies = jiffies_64 + 4;
- endif
-else
+ #endif
+#else
jiffies = jiffies_64;
-endif
+#endif
SECTIONS
{
};
struct {
- /* Virtual processing elements */
- struct list_head vpe_list;
-
- /* Thread contexts */
- struct list_head tc_list;
+ spinlock_t vpe_list_lock;
+ struct list_head vpe_list; /* Virtual processing elements */
+ spinlock_t tc_list_lock;
+ struct list_head tc_list; /* Thread contexts */
} vpecontrol = {
- .vpe_list = LIST_HEAD_INIT(vpecontrol.vpe_list),
- .tc_list = LIST_HEAD_INIT(vpecontrol.tc_list)
+ .vpe_list_lock = SPIN_LOCK_UNLOCKED,
+ .vpe_list = LIST_HEAD_INIT(vpecontrol.vpe_list),
+ .tc_list_lock = SPIN_LOCK_UNLOCKED,
+ .tc_list = LIST_HEAD_INIT(vpecontrol.tc_list)
};
static void release_progmem(void *ptr);
/* get the vpe associated with this minor */
static struct vpe *get_vpe(int minor)
{
- struct vpe *v;
+ struct vpe *res, *v;
if (!cpu_has_mipsmt)
return NULL;
+ res = NULL;
+ spin_lock(&vpecontrol.vpe_list_lock);
list_for_each_entry(v, &vpecontrol.vpe_list, list) {
- if (v->minor == minor)
- return v;
+ if (v->minor == minor) {
+ res = v;
+ break;
+ }
}
+ spin_unlock(&vpecontrol.vpe_list_lock);
- return NULL;
+ return res;
}
/* get the vpe associated with this minor */
static struct tc *get_tc(int index)
{
- struct tc *t;
+ struct tc *res, *t;
+ res = NULL;
+ spin_lock(&vpecontrol.tc_list_lock);
list_for_each_entry(t, &vpecontrol.tc_list, list) {
- if (t->index == index)
- return t;
+ if (t->index == index) {
+ res = t;
+ break;
+ }
}
+ spin_unlock(&vpecontrol.tc_list_lock);
return NULL;
}
{
struct vpe *v;
- if ((v = kzalloc(sizeof(struct vpe), GFP_KERNEL)) == NULL) {
+ if ((v = kzalloc(sizeof(struct vpe), GFP_KERNEL)) == NULL)
return NULL;
- }
INIT_LIST_HEAD(&v->tc);
+ spin_lock(&vpecontrol.vpe_list_lock);
list_add_tail(&v->list, &vpecontrol.vpe_list);
+ spin_unlock(&vpecontrol.vpe_list_lock);
INIT_LIST_HEAD(&v->notify);
v->minor = minor;
+
return v;
}
INIT_LIST_HEAD(&tc->tc);
tc->index = index;
+
+ spin_lock(&vpecontrol.tc_list_lock);
list_add_tail(&tc->list, &vpecontrol.tc_list);
+ spin_unlock(&vpecontrol.tc_list_lock);
out:
return tc;
kfree(v);
}
-static void dump_mtregs(void)
+static void __maybe_unused dump_mtregs(void)
{
unsigned long val;
enum vpe_state state;
struct vpe_notifications *not;
struct vpe *v;
- int ret, err = 0;
+ int ret;
- lock_kernel();
if (minor != iminor(inode)) {
/* assume only 1 device at the moment. */
- printk(KERN_WARNING "VPE loader: only vpe1 is supported\n");
- err = -ENODEV;
- goto out;
+ pr_warning("VPE loader: only vpe1 is supported\n");
+
+ return -ENODEV;
}
if ((v = get_vpe(tclimit)) == NULL) {
- printk(KERN_WARNING "VPE loader: unable to get vpe\n");
- err = -ENODEV;
- goto out;
+ pr_warning("VPE loader: unable to get vpe\n");
+
+ return -ENODEV;
}
state = xchg(&v->state, VPE_STATE_INUSE);
v->shared_ptr = NULL;
v->__start = 0;
-out:
unlock_kernel();
+
return 0;
}
{
struct vpe *v, *n;
+ device_del(&vpe_device);
+ unregister_chrdev(major, module_name);
+
+ /* No locking needed here */
list_for_each_entry_safe(v, n, &vpecontrol.vpe_list, list) {
- if (v->state != VPE_STATE_UNUSED) {
+ if (v->state != VPE_STATE_UNUSED)
release_vpe(v);
- }
}
-
- device_del(&vpe_device);
- unregister_chrdev(major, module_name);
}
module_init(vpe_module_init);
/* And the same for proc */
-int proc_dolasatstring(ctl_table *table, int write, struct file *filp,
+int proc_dolasatstring(ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
int r;
- r = proc_dostring(table, write, filp, buffer, lenp, ppos);
+ r = proc_dostring(table, write, buffer, lenp, ppos);
if ((!write) || r)
return r;
}
/* proc function to write EEPROM after changing int entry */
-int proc_dolasatint(ctl_table *table, int write, struct file *filp,
+int proc_dolasatint(ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
int r;
- r = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ r = proc_dointvec(table, write, buffer, lenp, ppos);
if ((!write) || r)
return r;
static int rtctmp;
/* proc function to read/write RealTime Clock */
-int proc_dolasatrtc(ctl_table *table, int write, struct file *filp,
+int proc_dolasatrtc(ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
struct timespec ts;
if (rtctmp < 0)
rtctmp = 0;
}
- r = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ r = proc_dointvec(table, write, buffer, lenp, ppos);
if (r)
return r;
#endif
#ifdef CONFIG_INET
-int proc_lasat_ip(ctl_table *table, int write, struct file *filp,
+int proc_lasat_ip(ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
unsigned int ip;
return 0;
}
-int proc_lasat_prid(ctl_table *table, int write, struct file *filp,
+int proc_lasat_prid(ctl_table *table, int write,
void *buffer, size_t *lenp, loff_t *ppos)
{
int r;
- r = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ r = proc_dointvec(table, write, buffer, lenp, ppos);
if (r < 0)
return r;
if (write) {
*/
static void mips_sc_inv(unsigned long addr, unsigned long size)
{
+ unsigned long lsize = cpu_scache_line_size();
+ unsigned long almask = ~(lsize - 1);
+
+ cache_op(Hit_Writeback_Inv_SD, addr & almask);
+ cache_op(Hit_Writeback_Inv_SD, (addr + size - 1) & almask);
blast_inv_scache_range(addr, addr + size);
}
unsigned int ctrl;
unsigned long long reset_counter1;
unsigned long long reset_counter2;
- int cnt1_enalbed, cnt2_enalbed;
+ int cnt1_enabled, cnt2_enabled;
} reg;
DEFINE_SPINLOCK(sample_lock);
reg.ctrl = ctrl;
- reg.cnt1_enalbed = cfg[0].enabled;
- reg.cnt2_enalbed = cfg[1].enabled;
+ reg.cnt1_enabled = cfg[0].enabled;
+ reg.cnt2_enabled = cfg[1].enabled;
}
static void loongson2_cpu_start(void *args)
{
/* Start all counters on current CPU */
- if (reg.cnt1_enalbed || reg.cnt2_enalbed)
+ if (reg.cnt1_enabled || reg.cnt2_enabled)
write_c0_perfctrl(reg.ctrl);
}
*/
/* Check whether the irq belongs to me */
- enabled = reg.cnt1_enalbed | reg.cnt2_enalbed;
+ enabled = reg.cnt1_enabled | reg.cnt2_enabled;
if (!enabled)
return IRQ_NONE;
spin_lock_irqsave(&sample_lock, flags);
if (counter1 & LOONGSON2_PERFCNT_OVERFLOW) {
- if (reg.cnt1_enalbed)
+ if (reg.cnt1_enabled)
oprofile_add_sample(regs, 0);
counter1 = reg.reset_counter1;
}
if (counter2 & LOONGSON2_PERFCNT_OVERFLOW) {
- if (reg.cnt2_enalbed)
+ if (reg.cnt2_enabled)
oprofile_add_sample(regs, 1);
counter2 = reg.reset_counter2;
}
unsigned long intr;
unsigned long value;
static char pciirqflag;
+ int ret;
#if defined(CONFIG_PMC_MSP7120_GW) || defined(CONFIG_PMC_MSP7120_EVAL)
unsigned int vpe_status;
#endif
* allocation assigns an interrupt handler to the interrupt.
*/
if (pciirqflag == 0) {
- request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
+ ret = request_irq(MSP_INT_PCI,/* Hardcoded internal MSP7120 wiring */
bpci_interrupt,
IRQF_SHARED | IRQF_DISABLED,
"PMC MSP PCI Host",
preg);
+ if (ret != 0)
+ return ret;
pciirqflag = ~0;
}
REMOTE_HUB_SEND_INTR(COMPACT_TO_NASID_NODEID(cpu_to_node(destid)), irq);
}
-static void ip27_send_ipi(const struct cpumask *mask, unsigned int action)
+static void ip27_send_ipi_mask(const struct cpumask *mask, unsigned int action)
{
unsigned int i;
unsigned long flags;
unsigned int irq_dirty;
- if (cpumask_weight(mask) != 1) {
- printk("attempted to set irq affinity for irq %d to multiple CPUs\n", irq);
- return -1;
- }
i = cpumask_first(mask);
/* Convert logical CPU to physical CPU */
static int sbprof_tb_open(struct inode *inode, struct file *filp)
{
int minor;
- int err = 0;
- lock_kernel();
minor = iminor(inode);
- if (minor != 0) {
- err = -ENODEV;
- goto out;
- }
+ if (minor != 0)
+ return -ENODEV;
- if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED) {
- err = -EBUSY;
- goto out;
- }
+ if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED)
+ return -EBUSY;
memset(&sbp, 0, sizeof(struct sbprof_tb));
sbp.sbprof_tbbuf = vmalloc(MAX_TBSAMPLE_BYTES);
if (!sbp.sbprof_tbbuf) {
- err = -ENOMEM;
- goto out;
+ sbp.open = SB_CLOSED;
+ wmb();
+ return -ENOMEM;
}
+
memset(sbp.sbprof_tbbuf, 0, MAX_TBSAMPLE_BYTES);
init_waitqueue_head(&sbp.tb_sync);
init_waitqueue_head(&sbp.tb_read);
mutex_init(&sbp.lock);
sbp.open = SB_OPEN;
+ wmb();
- out:
- unlock_kernel();
- return err;
+ return 0;
}
static int sbprof_tb_release(struct inode *inode, struct file *filp)
int minor;
minor = iminor(inode);
- if (minor != 0 || !sbp.open)
+ if (minor != 0 || sbp.open != SB_CLOSED)
return -ENODEV;
mutex_lock(&sbp.lock);
sbprof_zbprof_stop();
vfree(sbp.sbprof_tbbuf);
- sbp.open = 0;
+ sbp.open = SB_CLOSED;
+ wmb();
mutex_unlock(&sbp.lock);
}
tb_dev = dev;
- sbp.open = 0;
+ sbp.open = SB_CLOSED;
+ wmb();
tb_period = zbbus_mhz * 10000LL;
pr_info(DEVNAME ": initialized - tb_period = %lld\n",
(long long) tb_period);
break;
}
ts->tv_sec = sec;
- tv->tv_nsec = 0;
+ ts->tv_nsec = 0;
}
int rtc_mips_set_time(unsigned long sec)
struct __large_struct { unsigned long buf[100]; };
#define __m(x) (*(struct __large_struct *)(x))
-#define __get_user_nocheck(x, ptr, size) \
-({ \
- __typeof(*(ptr)) __gu_val; \
- unsigned long __gu_addr; \
- int __gu_err; \
- __gu_addr = (unsigned long) (ptr); \
- switch (size) { \
- case 1: __get_user_asm("bu"); break; \
- case 2: __get_user_asm("hu"); break; \
- case 4: __get_user_asm("" ); break; \
- default: __get_user_unknown(); break; \
- } \
- x = (__typeof__(*(ptr))) __gu_val; \
- __gu_err; \
+#define __get_user_nocheck(x, ptr, size) \
+({ \
+ unsigned long __gu_addr; \
+ int __gu_err; \
+ __gu_addr = (unsigned long) (ptr); \
+ switch (size) { \
+ case 1: { \
+ unsigned char __gu_val; \
+ __get_user_asm("bu"); \
+ (x) = *(__force __typeof__(*(ptr))*) &__gu_val; \
+ break; \
+ } \
+ case 2: { \
+ unsigned short __gu_val; \
+ __get_user_asm("hu"); \
+ (x) = *(__force __typeof__(*(ptr))*) &__gu_val; \
+ break; \
+ } \
+ case 4: { \
+ unsigned int __gu_val; \
+ __get_user_asm(""); \
+ (x) = *(__force __typeof__(*(ptr))*) &__gu_val; \
+ break; \
+ } \
+ default: \
+ __get_user_unknown(); \
+ break; \
+ } \
+ __gu_err; \
})
-#define __get_user_check(x, ptr, size) \
-({ \
- __typeof__(*(ptr)) __gu_val; \
- unsigned long __gu_addr; \
- int __gu_err; \
- __gu_addr = (unsigned long) (ptr); \
- if (likely(__access_ok(__gu_addr,size))) { \
- switch (size) { \
- case 1: __get_user_asm("bu"); break; \
- case 2: __get_user_asm("hu"); break; \
- case 4: __get_user_asm("" ); break; \
- default: __get_user_unknown(); break; \
- } \
- } \
- else { \
- __gu_err = -EFAULT; \
- __gu_val = 0; \
- } \
- x = (__typeof__(*(ptr))) __gu_val; \
- __gu_err; \
+#define __get_user_check(x, ptr, size) \
+({ \
+ int _e; \
+ if (likely(__access_ok((unsigned long) (ptr), (size)))) \
+ _e = __get_user_nocheck((x), (ptr), (size)); \
+ else { \
+ _e = -EFAULT; \
+ (x) = (__typeof__(x))0; \
+ } \
+ _e; \
})
#define __get_user_asm(INSN) \
RO_DATA(PAGE_SIZE)
/* writeable */
- .data : { /* Data */
- DATA_DATA
- CONSTRUCTORS
- }
-
- .data_nosave : { NOSAVE_DATA; }
-
- .data.page_aligned : { PAGE_ALIGNED_DATA(PAGE_SIZE); }
- .data.cacheline_aligned : { CACHELINE_ALIGNED_DATA(32); }
-
- /* rarely changed data like cpu maps */
- . = ALIGN(32);
- .data.read_mostly : AT(ADDR(.data.read_mostly)) {
- READ_MOSTLY_DATA(32);
- _edata = .; /* End of data section */
- }
-
- .data.init_task : { INIT_TASK_DATA(THREAD_SIZE); }
+ RW_DATA_SECTION(32, PAGE_SIZE, THREAD_SIZE)
+ _edata = .;
/* might get freed after init */
. = ALIGN(PAGE_SIZE);
/* will be freed after init */
. = ALIGN(PAGE_SIZE); /* Init code and data */
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT;
- _einittext = .;
- }
- .init.data : { INIT_DATA; }
- .setup.init : { INIT_SETUP(16); }
-
- __initcall_start = .;
- .initcall.init : {
- INITCALLS
- }
- __initcall_end = .;
- .con_initcall.init : { CON_INITCALL; }
-
- SECURITY_INIT
+ INIT_TEXT_SECTION(PAGE_SIZE)
+ INIT_DATA_SECTION(16)
. = ALIGN(4);
__alt_instructions = .;
.altinstructions : { *(.altinstructions) }
.exit.text : { EXIT_TEXT; }
.exit.data : { EXIT_DATA; }
- .init.ramfs : { INIT_RAM_FS; }
-
PERCPU(32)
. = ALIGN(PAGE_SIZE);
__init_end = .;
extern unsigned long mn10300_iobclk;
extern unsigned long mn10300_tsc_per_HZ;
-#define MN10300_IOCLK ((unsigned long)mn10300_ioclk)
+#define MN10300_IOCLK mn10300_ioclk
/* If this processors has a another clock, uncomment the below. */
-/* #define MN10300_IOBCLK ((unsigned long)mn10300_iobclk) */
+/* #define MN10300_IOBCLK mn10300_iobclk */
#else /* !CONFIG_MN10300_RTC */
#define MN10300_TSCCLK MN10300_IOCLK
#ifdef CONFIG_MN10300_RTC
-#define MN10300_TSC_PER_HZ ((unsigned long)mn10300_tsc_per_HZ)
+#define MN10300_TSC_PER_HZ mn10300_tsc_per_HZ
#else /* !CONFIG_MN10300_RTC */
#define MN10300_TSC_PER_HZ (MN10300_TSCCLK/HZ)
#endif /* !CONFIG_MN10300_RTC */
extern unsigned long mn10300_iobclk;
extern unsigned long mn10300_tsc_per_HZ;
-#define MN10300_IOCLK ((unsigned long)mn10300_ioclk)
+#define MN10300_IOCLK mn10300_ioclk
/* If this processors has a another clock, uncomment the below. */
-/* #define MN10300_IOBCLK ((unsigned long)mn10300_iobclk) */
+/* #define MN10300_IOBCLK mn10300_iobclk */
#else /* !CONFIG_MN10300_RTC */
#define MN10300_TSCCLK MN10300_IOCLK
#ifdef CONFIG_MN10300_RTC
-#define MN10300_TSC_PER_HZ ((unsigned long)mn10300_tsc_per_HZ)
+#define MN10300_TSC_PER_HZ mn10300_tsc_per_HZ
#else /* !CONFIG_MN10300_RTC */
#define MN10300_TSC_PER_HZ (MN10300_TSCCLK/HZ)
#endif /* !CONFIG_MN10300_RTC */
#define F_SETOWN 12 /* for sockets. */
#define F_SETSIG 13 /* for sockets. */
#define F_GETSIG 14 /* for sockets. */
+#define F_GETOWN_EX 15
+#define F_SETOWN_EX 16
/* for posix fcntl() and lockf() */
#define F_RDLCK 01
*/
. = ALIGN(PAGE_SIZE);
data_start = .;
- . = ALIGN(16);
- /* Exception table */
- __ex_table : {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
+ EXCEPTION_TABLE(16)
NOTES
__stop___unwind = .;
}
- /* rarely changed data like cpu maps */
- . = ALIGN(16);
- .data.read_mostly : {
- *(.data.read_mostly)
- }
-
- . = ALIGN(L1_CACHE_BYTES);
/* Data */
- .data : {
- DATA_DATA
- CONSTRUCTORS
- }
-
- . = ALIGN(L1_CACHE_BYTES);
- .data.cacheline_aligned : {
- *(.data.cacheline_aligned)
- }
+ RW_DATA_SECTION(L1_CACHE_BYTES, PAGE_SIZE, THREAD_SIZE)
/* PA-RISC locks requires 16-byte alignment */
. = ALIGN(16);
*(.data.lock_aligned)
}
- /* nosave data is really only used for software suspend...it's here
- * just in case we ever implement it
- */
- . = ALIGN(PAGE_SIZE);
- __nosave_begin = .;
- .data_nosave : {
- *(.data.nosave)
- }
- . = ALIGN(PAGE_SIZE);
- __nosave_end = .;
-
/* End of data section */
_edata = .;
}
__bss_stop = .;
-
- /* assembler code expects init_task to be 16k aligned */
- . = ALIGN(16384);
- /* init_task */
- .data.init_task : {
- *(.data.init_task)
- }
-
#ifdef CONFIG_64BIT
. = ALIGN(16);
/* Linkage tables */
/* reserve space for interrupt stack by aligning __init* to 16k */
. = ALIGN(16384);
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
- .init.data : {
- INIT_DATA
- }
- . = ALIGN(16);
- .init.setup : {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
- }
- .initcall.init : {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
- }
- .con_initcall.init : {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
- }
- SECURITY_INIT
-
- /* alternate instruction replacement. This is a mechanism x86 uses
- * to detect the CPU type and replace generic instruction sequences
- * with CPU specific ones. We don't currently do this in PA, but
- * it seems like a good idea...
- */
- . = ALIGN(4);
- .altinstructions : {
- __alt_instructions = .;
- *(.altinstructions)
- __alt_instructions_end = .;
- }
- .altinstr_replacement : {
- *(.altinstr_replacement)
- }
-
- /* .exit.text is discard at runtime, not link time, to deal with references
- * from .altinstructions and .eh_frame
- */
- .exit.text : {
- EXIT_TEXT
- }
- .exit.data : {
- EXIT_DATA
- }
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(PAGE_SIZE);
- .init.ramfs : {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
- }
-#endif
+ INIT_TEXT_SECTION(16384)
+ INIT_DATA_SECTION(16)
PERCPU(PAGE_SIZE)
. = ALIGN(PAGE_SIZE);
config NODES_SHIFT
int
+ default "8" if PPC64
default "4"
depends on NEED_MULTIPLE_NODES
+config MAX_ACTIVE_REGIONS
+ int
+ default "256" if PPC64
+ default "32"
+
config ARCH_SELECT_MEMORY_MODEL
def_bool y
depends on PPC64
boot := arch/$(ARCH)/boot
+ifeq ($(CONFIG_RELOCATABLE),y)
+quiet_cmd_relocs_check = CALL $<
+ cmd_relocs_check = perl $< "$(OBJDUMP)" "$(obj)/vmlinux"
+
+PHONY += relocs_check
+relocs_check: arch/powerpc/relocs_check.pl vmlinux
+ $(call cmd,relocs_check)
+
+zImage: relocs_check
+endif
+
$(BOOT_TARGETS): vmlinux
$(Q)$(MAKE) ARCH=ppc64 $(build)=$(boot) $(patsubst %,$(boot)/%,$@)
/* DMA operations on that device */
struct dma_map_ops *dma_ops;
- void *dma_data;
+
+ /*
+ * When an iommu is in use, dma_data is used as a ptr to the base of the
+ * iommu_table. Otherwise, it is a simple numerical offset.
+ */
+ union {
+ dma_addr_t dma_offset;
+ void *iommu_table_base;
+ } dma_data;
+
#ifdef CONFIG_SWIOTLB
dma_addr_t max_direct_dma_addr;
#endif
extern void dma_direct_free_coherent(struct device *dev, size_t size,
void *vaddr, dma_addr_t dma_handle);
-extern unsigned long get_dma_direct_offset(struct device *dev);
#ifdef CONFIG_NOT_COHERENT_CACHE
/*
dev->archdata.dma_ops = ops;
}
+/*
+ * get_dma_offset()
+ *
+ * Get the dma offset on configurations where the dma address can be determined
+ * from the physical address by looking at a simple offset. Direct dma and
+ * swiotlb use this function, but it is typically not used by implementations
+ * with an iommu.
+ */
+static inline dma_addr_t get_dma_offset(struct device *dev)
+{
+ if (dev)
+ return dev->archdata.dma_data.dma_offset;
+
+ return PCI_DRAM_OFFSET;
+}
+
+static inline void set_dma_offset(struct device *dev, dma_addr_t off)
+{
+ if (dev)
+ dev->archdata.dma_data.dma_offset = off;
+}
+
/* this will be removed soon */
#define flush_write_buffers()
static inline dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
{
- return paddr + get_dma_direct_offset(dev);
+ return paddr + get_dma_offset(dev);
}
static inline phys_addr_t dma_to_phys(struct device *dev, dma_addr_t daddr)
{
- return daddr - get_dma_direct_offset(dev);
+ return daddr - get_dma_offset(dev);
}
#define dma_alloc_noncoherent(d, s, h, f) dma_alloc_coherent(d, s, h, f)
--- /dev/null
+/*
+ * Freescale MPC83XX / MPC85XX DMA Controller
+ *
+ * Copyright (c) 2009 Ira W. Snyder <iws@ovro.caltech.edu>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#ifndef __ARCH_POWERPC_ASM_FSLDMA_H__
+#define __ARCH_POWERPC_ASM_FSLDMA_H__
+
+#include <linux/dmaengine.h>
+
+/*
+ * Definitions for the Freescale DMA controller's DMA_SLAVE implemention
+ *
+ * The Freescale DMA_SLAVE implementation was designed to handle many-to-many
+ * transfers. An example usage would be an accelerated copy between two
+ * scatterlists. Another example use would be an accelerated copy from
+ * multiple non-contiguous device buffers into a single scatterlist.
+ *
+ * A DMA_SLAVE transaction is defined by a struct fsl_dma_slave. This
+ * structure contains a list of hardware addresses that should be copied
+ * to/from the scatterlist passed into device_prep_slave_sg(). The structure
+ * also has some fields to enable hardware-specific features.
+ */
+
+/**
+ * struct fsl_dma_hw_addr
+ * @entry: linked list entry
+ * @address: the hardware address
+ * @length: length to transfer
+ *
+ * Holds a single physical hardware address / length pair for use
+ * with the DMAEngine DMA_SLAVE API.
+ */
+struct fsl_dma_hw_addr {
+ struct list_head entry;
+
+ dma_addr_t address;
+ size_t length;
+};
+
+/**
+ * struct fsl_dma_slave
+ * @addresses: a linked list of struct fsl_dma_hw_addr structures
+ * @request_count: value for DMA request count
+ * @src_loop_size: setup and enable constant source-address DMA transfers
+ * @dst_loop_size: setup and enable constant destination address DMA transfers
+ * @external_start: enable externally started DMA transfers
+ * @external_pause: enable externally paused DMA transfers
+ *
+ * Holds a list of address / length pairs for use with the DMAEngine
+ * DMA_SLAVE API implementation for the Freescale DMA controller.
+ */
+struct fsl_dma_slave {
+
+ /* List of hardware address/length pairs */
+ struct list_head addresses;
+
+ /* Support for extra controller features */
+ unsigned int request_count;
+ unsigned int src_loop_size;
+ unsigned int dst_loop_size;
+ bool external_start;
+ bool external_pause;
+};
+
+/**
+ * fsl_dma_slave_append - add an address/length pair to a struct fsl_dma_slave
+ * @slave: the &struct fsl_dma_slave to add to
+ * @address: the hardware address to add
+ * @length: the length of bytes to transfer from @address
+ *
+ * Add a hardware address/length pair to a struct fsl_dma_slave. Returns 0 on
+ * success, -ERRNO otherwise.
+ */
+static inline int fsl_dma_slave_append(struct fsl_dma_slave *slave,
+ dma_addr_t address, size_t length)
+{
+ struct fsl_dma_hw_addr *addr;
+
+ addr = kzalloc(sizeof(*addr), GFP_ATOMIC);
+ if (!addr)
+ return -ENOMEM;
+
+ INIT_LIST_HEAD(&addr->entry);
+ addr->address = address;
+ addr->length = length;
+
+ list_add_tail(&addr->entry, &slave->addresses);
+ return 0;
+}
+
+/**
+ * fsl_dma_slave_free - free a struct fsl_dma_slave
+ * @slave: the struct fsl_dma_slave to free
+ *
+ * Free a struct fsl_dma_slave and all associated address/length pairs
+ */
+static inline void fsl_dma_slave_free(struct fsl_dma_slave *slave)
+{
+ struct fsl_dma_hw_addr *addr, *tmp;
+
+ if (slave) {
+ list_for_each_entry_safe(addr, tmp, &slave->addresses, entry) {
+ list_del(&addr->entry);
+ kfree(addr);
+ }
+
+ kfree(slave);
+ }
+}
+
+/**
+ * fsl_dma_slave_alloc - allocate a struct fsl_dma_slave
+ * @gfp: the flags to pass to kmalloc when allocating this structure
+ *
+ * Allocate a struct fsl_dma_slave for use by the DMA_SLAVE API. Returns a new
+ * struct fsl_dma_slave on success, or NULL on failure.
+ */
+static inline struct fsl_dma_slave *fsl_dma_slave_alloc(gfp_t gfp)
+{
+ struct fsl_dma_slave *slave;
+
+ slave = kzalloc(sizeof(*slave), gfp);
+ if (!slave)
+ return NULL;
+
+ INIT_LIST_HEAD(&slave->addresses);
+ return slave;
+}
+
+#endif /* __ARCH_POWERPC_ASM_FSLDMA_H__ */
struct scatterlist;
+static inline void set_iommu_table_base(struct device *dev, void *base)
+{
+ dev->archdata.dma_data.iommu_table_base = base;
+}
+
+static inline void *get_iommu_table_base(struct device *dev)
+{
+ return dev->archdata.dma_data.iommu_table_base;
+}
+
/* Frees table for an individual device node */
extern void iommu_free_table(struct iommu_table *tbl, const char *node_name);
void release_pmc_hardware(void);
void ppc_enable_pmcs(void);
-#ifdef CONFIG_PPC64
+#ifdef CONFIG_PPC_BOOK3S_64
#include <asm/lppaca.h>
static inline void ppc_set_pmu_inuse(int inuse)
#define _PAGE_NO_CACHE 0x004 /* I: caching is inhibited */
#define _PAGE_WRITETHRU 0x008 /* W: caching is write-through */
#define _PAGE_USER 0x010 /* matches one of the zone permission bits */
+#define _PAGE_SPECIAL 0x020 /* software: Special page */
#define _PAGE_RW 0x040 /* software: Writes permitted */
#define _PAGE_DIRTY 0x080 /* software: dirty page */
#define _PAGE_HWWRITE 0x100 /* hardware: Dirty & RW, set in exception */
#define _PAGE_FILE 0x0002 /* when !present: nonlinear file mapping */
#define _PAGE_NO_CACHE 0x0002 /* I: cache inhibit */
#define _PAGE_SHARED 0x0004 /* No ASID (context) compare */
+#define _PAGE_SPECIAL 0x0008 /* SW entry, forced to 0 by the TLB miss */
/* These five software bits must be masked out when the entry is loaded
* into the TLB.
#ifndef _PAGE_WRITETHRU
#define _PAGE_WRITETHRU 0
#endif
-#ifndef _PAGE_SPECIAL
-#define _PAGE_SPECIAL 0
-#endif
#ifndef _PAGE_4K_PFN
#define _PAGE_4K_PFN 0
#endif
#define HAVE_PAGE_AGP
/* Advertise support for _PAGE_SPECIAL */
-#ifdef _PAGE_SPECIAL
#define __HAVE_ARCH_PTE_SPECIAL
-#endif
static void *dma_iommu_alloc_coherent(struct device *dev, size_t size,
dma_addr_t *dma_handle, gfp_t flag)
{
- return iommu_alloc_coherent(dev, dev->archdata.dma_data, size,
+ return iommu_alloc_coherent(dev, get_iommu_table_base(dev), size,
dma_handle, device_to_mask(dev), flag,
dev_to_node(dev));
}
static void dma_iommu_free_coherent(struct device *dev, size_t size,
void *vaddr, dma_addr_t dma_handle)
{
- iommu_free_coherent(dev->archdata.dma_data, size, vaddr, dma_handle);
+ iommu_free_coherent(get_iommu_table_base(dev), size, vaddr, dma_handle);
}
/* Creates TCEs for a user provided buffer. The user buffer must be
enum dma_data_direction direction,
struct dma_attrs *attrs)
{
- return iommu_map_page(dev, dev->archdata.dma_data, page, offset, size,
- device_to_mask(dev), direction, attrs);
+ return iommu_map_page(dev, get_iommu_table_base(dev), page, offset,
+ size, device_to_mask(dev), direction, attrs);
}
size_t size, enum dma_data_direction direction,
struct dma_attrs *attrs)
{
- iommu_unmap_page(dev->archdata.dma_data, dma_handle, size, direction,
+ iommu_unmap_page(get_iommu_table_base(dev), dma_handle, size, direction,
attrs);
}
int nelems, enum dma_data_direction direction,
struct dma_attrs *attrs)
{
- return iommu_map_sg(dev, dev->archdata.dma_data, sglist, nelems,
+ return iommu_map_sg(dev, get_iommu_table_base(dev), sglist, nelems,
device_to_mask(dev), direction, attrs);
}
int nelems, enum dma_data_direction direction,
struct dma_attrs *attrs)
{
- iommu_unmap_sg(dev->archdata.dma_data, sglist, nelems, direction,
+ iommu_unmap_sg(get_iommu_table_base(dev), sglist, nelems, direction,
attrs);
}
/* We support DMA to/from any memory page via the iommu */
static int dma_iommu_dma_supported(struct device *dev, u64 mask)
{
- struct iommu_table *tbl = dev->archdata.dma_data;
+ struct iommu_table *tbl = get_iommu_table_base(dev);
if (!tbl || tbl->it_offset > mask) {
printk(KERN_INFO
* default the offset is PCI_DRAM_OFFSET.
*/
-unsigned long get_dma_direct_offset(struct device *dev)
-{
- if (dev)
- return (unsigned long)dev->archdata.dma_data;
-
- return PCI_DRAM_OFFSET;
-}
void *dma_direct_alloc_coherent(struct device *dev, size_t size,
dma_addr_t *dma_handle, gfp_t flag)
ret = __dma_alloc_coherent(dev, size, dma_handle, flag);
if (ret == NULL)
return NULL;
- *dma_handle += get_dma_direct_offset(dev);
+ *dma_handle += get_dma_offset(dev);
return ret;
#else
struct page *page;
return NULL;
ret = page_address(page);
memset(ret, 0, size);
- *dma_handle = virt_to_abs(ret) + get_dma_direct_offset(dev);
+ *dma_handle = virt_to_abs(ret) + get_dma_offset(dev);
return ret;
#endif
int i;
for_each_sg(sgl, sg, nents, i) {
- sg->dma_address = sg_phys(sg) + get_dma_direct_offset(dev);
+ sg->dma_address = sg_phys(sg) + get_dma_offset(dev);
sg->dma_length = sg->length;
__dma_sync_page(sg_page(sg), sg->offset, sg->length, direction);
}
{
BUG_ON(dir == DMA_NONE);
__dma_sync_page(page, offset, size, dir);
- return page_to_phys(page) + offset + get_dma_direct_offset(dev);
+ return page_to_phys(page) + offset + get_dma_offset(dev);
}
static inline void dma_direct_unmap_page(struct device *dev,
#include <asm/cputable.h>
#include <asm/setup.h>
#include <asm/thread_info.h>
-#include <asm/reg.h>
#include <asm/exception-64e.h>
#include <asm/bug.h>
#include <asm/irqflags.h>
/* Hook up default DMA ops */
sd->dma_ops = pci_dma_ops;
- sd->dma_data = (void *)PCI_DRAM_OFFSET;
+ set_dma_offset(&dev->dev, PCI_DRAM_OFFSET);
/* Additional platform DMA/iommu setup */
if (ppc_md.pci_dma_dev_setup)
unsigned long arch_randomize_brk(struct mm_struct *mm)
{
- unsigned long ret = PAGE_ALIGN(mm->brk + brk_rnd());
+ unsigned long base = mm->brk;
+ unsigned long ret;
+
+#ifdef CONFIG_PPC64
+ /*
+ * If we are using 1TB segments and we are allowed to randomise
+ * the heap, we can put it above 1TB so it is backed by a 1TB
+ * segment. Otherwise the heap will be in the bottom 1TB
+ * which always uses 256MB segments and this may result in a
+ * performance penalty.
+ */
+ if (!is_32bit_task() && (mmu_highuser_ssize == MMU_SEGSIZE_1T))
+ base = max_t(unsigned long, mm->brk, 1UL << SID_SHIFT_1T);
+#endif
+
+ ret = PAGE_ALIGN(base + brk_rnd());
if (ret < mm->brk)
return mm->brk;
root = call_prom("open", 1, 1, ADDR("/"));
if (root != 0) {
/* try calling the ibm,client-architecture-support method */
- prom_printf("Calling ibm,client-architecture...");
+ prom_printf("Calling ibm,client-architecture-support...");
if (call_prom_ret("call-method", 3, 2, &ret,
ADDR("ibm,client-architecture-support"),
root,
return;
}
call_prom("close", 1, 0, root);
+ prom_printf(" not implemented\n");
}
/* no ibm,client-architecture-support call, try the old way */
goto fail_mmapsem;
}
+ /*
+ * Put vDSO base into mm struct. We need to do this before calling
+ * install_special_mapping or the perf counter mmap tracking code
+ * will fail to recognise it as a vDSO (since arch_vma_name fails).
+ */
+ current->mm->context.vdso_base = vdso_base;
+
/*
* our vma flags don't have VM_WRITE so by default, the process isn't
* allowed to write those pages.
VM_MAYREAD|VM_MAYWRITE|VM_MAYEXEC|
VM_ALWAYSDUMP,
vdso_pagelist);
- if (rc)
+ if (rc) {
+ current->mm->context.vdso_base = 0;
goto fail_mmapsem;
-
- /* Put vDSO base into mm struct */
- current->mm->context.vdso_base = vdso_base;
+ }
up_write(&mm->mmap_sem);
return 0;
return NULL;
tbl = kmalloc(sizeof(*tbl), GFP_KERNEL);
+ if (tbl == NULL)
+ return NULL;
of_parse_dma_window(dev->dev.archdata.of_node, dma_window,
&tbl->it_index, &offset, &size);
vio_cmo_set_dma_ops(viodev);
else
viodev->dev.archdata.dma_ops = &dma_iommu_ops;
- viodev->dev.archdata.dma_data = vio_build_iommu_table(viodev);
+ set_iommu_table_base(&viodev->dev, vio_build_iommu_table(viodev));
set_dev_node(&viodev->dev, of_node_to_nid(of_node));
/* init generic 'struct device' fields: */
#include <asm/page.h>
#include <asm-generic/vmlinux.lds.h>
#include <asm/cache.h>
+#include <asm/thread_info.h>
ENTRY(_stext)
/* Read-only data */
RODATA
- /* Exception & bug tables */
- __ex_table : AT(ADDR(__ex_table) - LOAD_OFFSET) {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
+ EXCEPTION_TABLE(0)
NOTES :kernel :notes
*/
. = ALIGN(PAGE_SIZE);
__init_begin = .;
-
- .init.text : AT(ADDR(.init.text) - LOAD_OFFSET) {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- } :kernel
+ INIT_TEXT_SECTION(PAGE_SIZE) :kernel
/* .exit.text is discarded at runtime, not link time,
* to deal with references from __bug_table
#endif
}
- . = ALIGN(16);
.init.setup : AT(ADDR(.init.setup) - LOAD_OFFSET) {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
+ INIT_SETUP(16)
}
.initcall.init : AT(ADDR(.initcall.init) - LOAD_OFFSET) {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
- }
+ INIT_CALLS
+ }
.con_initcall.init : AT(ADDR(.con_initcall.init) - LOAD_OFFSET) {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
+ CON_INITCALL
}
SECURITY_INIT
__stop___fw_ftr_fixup = .;
}
#endif
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(PAGE_SIZE);
.init.ramfs : AT(ADDR(.init.ramfs) - LOAD_OFFSET) {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
+ INIT_RAM_FS
}
-#endif
+
PERCPU(PAGE_SIZE)
. = ALIGN(8);
#endif
/* The initial task and kernel stack */
-#ifdef CONFIG_PPC32
- . = ALIGN(8192);
-#else
- . = ALIGN(16384);
-#endif
.data.init_task : AT(ADDR(.data.init_task) - LOAD_OFFSET) {
- *(.data.init_task)
+ INIT_TASK_DATA(THREAD_SIZE)
}
- . = ALIGN(PAGE_SIZE);
.data.page_aligned : AT(ADDR(.data.page_aligned) - LOAD_OFFSET) {
- *(.data.page_aligned)
+ PAGE_ALIGNED_DATA(PAGE_SIZE)
}
- . = ALIGN(L1_CACHE_BYTES);
.data.cacheline_aligned : AT(ADDR(.data.cacheline_aligned) - LOAD_OFFSET) {
- *(.data.cacheline_aligned)
+ CACHELINE_ALIGNED_DATA(L1_CACHE_BYTES)
}
- . = ALIGN(L1_CACHE_BYTES);
.data.read_mostly : AT(ADDR(.data.read_mostly) - LOAD_OFFSET) {
- *(.data.read_mostly)
+ READ_MOSTLY_DATA(L1_CACHE_BYTES)
}
- . = ALIGN(PAGE_SIZE);
.data_nosave : AT(ADDR(.data_nosave) - LOAD_OFFSET) {
- __nosave_begin = .;
- *(.data.nosave)
- . = ALIGN(PAGE_SIZE);
- __nosave_end = .;
+ NOSAVE_DATA
}
. = ALIGN(PAGE_SIZE);
* And finally the bss
*/
- .bss : AT(ADDR(.bss) - LOAD_OFFSET) {
- __bss_start = .;
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- __bss_stop = .;
- }
+ BSS_SECTION(0, 0, 0)
. = ALIGN(PAGE_SIZE);
_end = . ;
return single_open(file, kvmppc_exit_timing_show, inode->i_private);
}
-static struct file_operations kvmppc_exit_timing_fops = {
+static const struct file_operations kvmppc_exit_timing_fops = {
.owner = THIS_MODULE,
.open = kvmppc_exit_timing_open,
.read = seq_read,
#include <asm/tlbflush.h>
#include <asm/tlb.h>
+#include "mmu_decl.h"
+
DEFINE_PER_CPU(struct mmu_gather, mmu_gathers);
#ifdef CONFIG_SMP
* support falls into the same category.
*/
-static pte_t set_pte_filter(pte_t pte)
+static pte_t set_pte_filter(pte_t pte, unsigned long addr)
{
pte = __pte(pte_val(pte) & ~_PAGE_HPTEFLAGS);
if (pte_looks_normal(pte) && !(cpu_has_feature(CPU_FTR_COHERENT_ICACHE) ||
if (!pg)
return pte;
if (!test_bit(PG_arch_1, &pg->flags)) {
+#ifdef CONFIG_8xx
+ /* On 8xx, cache control instructions (particularly
+ * "dcbst" from flush_dcache_icache) fault as write
+ * operation if there is an unpopulated TLB entry
+ * for the address in question. To workaround that,
+ * we invalidate the TLB here, thus avoiding dcbst
+ * misbehaviour.
+ */
+ /* 8xx doesn't care about PID, size or ind args */
+ _tlbil_va(addr, 0, 0, 0);
+#endif /* CONFIG_8xx */
flush_dcache_icache_page(pg);
set_bit(PG_arch_1, &pg->flags);
}
* as we don't have two bits to spare for _PAGE_EXEC and _PAGE_HWEXEC so
* instead we "filter out" the exec permission for non clean pages.
*/
-static pte_t set_pte_filter(pte_t pte)
+static pte_t set_pte_filter(pte_t pte, unsigned long addr)
{
struct page *pg;
* this context might not have been activated yet when this
* is called.
*/
- pte = set_pte_filter(pte);
+ pte = set_pte_filter(pte, addr);
/* Perform the setting of the PTE */
__set_pte_at(mm, addr, ptep, pte, 0);
#include <asm/asm-offsets.h>
#include <asm/cputable.h>
#include <asm/pgtable.h>
-#include <asm/reg.h>
#include <asm/exception-64e.h>
#include <asm/ppc-opcode.h>
static void celleb_dma_dev_setup(struct device *dev)
{
dev->archdata.dma_ops = get_pci_dma_ops();
- dev->archdata.dma_data = (void *)celleb_dma_direct_offset;
+ set_dma_offset(dev, celleb_dma_direct_offset);
}
static void celleb_pci_dma_dev_setup(struct pci_dev *pdev)
static void cell_dma_dev_setup(struct device *dev)
{
- struct dev_archdata *archdata = &dev->archdata;
-
/* Order is important here, these are not mutually exclusive */
if (get_dma_ops(dev) == &dma_iommu_fixed_ops)
cell_dma_dev_setup_fixed(dev);
else if (get_pci_dma_ops() == &dma_iommu_ops)
- archdata->dma_data = cell_get_iommu_table(dev);
+ set_iommu_table_base(dev, cell_get_iommu_table(dev));
else if (get_pci_dma_ops() == &dma_direct_ops)
- archdata->dma_data = (void *)cell_dma_direct_offset;
+ set_dma_offset(dev, cell_dma_direct_offset);
else
BUG();
}
static void cell_dma_dev_setup_fixed(struct device *dev)
{
- struct dev_archdata *archdata = &dev->archdata;
u64 addr;
addr = cell_iommu_get_fixed_address(dev) + dma_iommu_fixed_base;
- archdata->dma_data = (void *)addr;
+ set_dma_offset(dev, addr);
dev_dbg(dev, "iommu: fixed addr = %llx\n", addr);
}
__simple_attr_check_format(__fmt, 0ull); \
return spufs_attr_open(inode, file, __get, __set, __fmt); \
} \
-static struct file_operations __fops = { \
+static const struct file_operations __fops = { \
.owner = THIS_MODULE, \
.open = __fops ## _open, \
.release = spufs_attr_release, \
return len;
}
-static struct vm_operations_struct spufs_mem_mmap_vmops = {
+static const struct vm_operations_struct spufs_mem_mmap_vmops = {
.fault = spufs_mem_mmap_fault,
.access = spufs_mem_mmap_access,
};
return spufs_ps_fault(vma, vmf, 0x4000, SPUFS_CNTL_MAP_SIZE);
}
-static struct vm_operations_struct spufs_cntl_mmap_vmops = {
+static const struct vm_operations_struct spufs_cntl_mmap_vmops = {
.fault = spufs_cntl_mmap_fault,
};
#endif
}
-static struct vm_operations_struct spufs_signal1_mmap_vmops = {
+static const struct vm_operations_struct spufs_signal1_mmap_vmops = {
.fault = spufs_signal1_mmap_fault,
};
#endif
}
-static struct vm_operations_struct spufs_signal2_mmap_vmops = {
+static const struct vm_operations_struct spufs_signal2_mmap_vmops = {
.fault = spufs_signal2_mmap_fault,
};
return spufs_ps_fault(vma, vmf, 0x0000, SPUFS_MSS_MAP_SIZE);
}
-static struct vm_operations_struct spufs_mss_mmap_vmops = {
+static const struct vm_operations_struct spufs_mss_mmap_vmops = {
.fault = spufs_mss_mmap_fault,
};
return spufs_ps_fault(vma, vmf, 0x0000, SPUFS_PS_MAP_SIZE);
}
-static struct vm_operations_struct spufs_psmap_mmap_vmops = {
+static const struct vm_operations_struct spufs_psmap_mmap_vmops = {
.fault = spufs_psmap_mmap_fault,
};
return spufs_ps_fault(vma, vmf, 0x3000, SPUFS_MFC_MAP_SIZE);
}
-static struct vm_operations_struct spufs_mfc_mmap_vmops = {
+static const struct vm_operations_struct spufs_mfc_mmap_vmops = {
.fault = spufs_mfc_mmap_fault,
};
pdn->iommu_table = iommu_init_table(tbl, -1);
else
kfree(tbl);
- pdev->dev.archdata.dma_data = pdn->iommu_table;
+ set_iommu_table_base(&pdev->dev, pdn->iommu_table);
}
#else
#define pci_dma_dev_setup_iseries NULL
}
#endif
- dev->dev.archdata.dma_data = &iommu_table_iobmap;
+ set_iommu_table_base(&dev->dev, &iommu_table_iobmap);
}
static void pci_dma_bus_setup_null(struct pci_bus *b) { }
return n_read * sizeof(struct dtl_entry);
}
-static struct file_operations dtl_fops = {
+static const struct file_operations dtl_fops = {
.open = dtl_file_open,
.release = dtl_file_release,
.read = dtl_file_read,
phb->node);
iommu_table_setparms(phb, dn, tbl);
PCI_DN(dn)->iommu_table = iommu_init_table(tbl, phb->node);
- dev->dev.archdata.dma_data = PCI_DN(dn)->iommu_table;
+ set_iommu_table_base(&dev->dev, PCI_DN(dn)->iommu_table);
return;
}
dn = dn->parent;
if (dn && PCI_DN(dn))
- dev->dev.archdata.dma_data = PCI_DN(dn)->iommu_table;
+ set_iommu_table_base(&dev->dev, PCI_DN(dn)->iommu_table);
else
printk(KERN_WARNING "iommu: Device %s has no iommu table\n",
pci_name(dev));
*/
if (dma_window == NULL || pdn->parent == NULL) {
pr_debug(" no dma window for device, linking to parent\n");
- dev->dev.archdata.dma_data = PCI_DN(pdn)->iommu_table;
+ set_iommu_table_base(&dev->dev, PCI_DN(pdn)->iommu_table);
return;
}
pr_debug(" found DMA window, table: %p\n", pci->iommu_table);
}
- dev->dev.archdata.dma_data = pci->iommu_table;
+ set_iommu_table_base(&dev->dev, pci->iommu_table);
}
#else /* CONFIG_PCI */
#define pci_dma_bus_setup_pSeries NULL
--- /dev/null
+#!/usr/bin/perl
+
+# Copyright © 2009 IBM Corporation
+
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License
+# as published by the Free Software Foundation; either version
+# 2 of the License, or (at your option) any later version.
+
+# This script checks the relcoations of a vmlinux for "suspicious"
+# relocations.
+
+use strict;
+use warnings;
+
+if ($#ARGV != 1) {
+ die "$0 [path to objdump] [path to vmlinux]\n";
+}
+
+# Have Kbuild supply the path to objdump so we handle cross compilation.
+my $objdump = shift;
+my $vmlinux = shift;
+my $bad_relocs_count = 0;
+my $bad_relocs = "";
+my $old_binutils = 0;
+
+open(FD, "$objdump -R $vmlinux|") or die;
+while (<FD>) {
+ study $_;
+
+ # Only look at relcoation lines.
+ next if (!/\s+R_/);
+
+ # These relocations are okay
+ next if (/R_PPC64_RELATIVE/ or /R_PPC64_NONE/ or
+ /R_PPC64_ADDR64\s+mach_/);
+
+ # If we see this type of relcoation it's an idication that
+ # we /may/ be using an old version of binutils.
+ if (/R_PPC64_UADDR64/) {
+ $old_binutils++;
+ }
+
+ $bad_relocs_count++;
+ $bad_relocs .= $_;
+}
+
+if ($bad_relocs_count) {
+ print "WARNING: $bad_relocs_count bad relocations\n";
+ print $bad_relocs;
+}
+
+if ($old_binutils) {
+ print "WARNING: You need at binutils >= 2.19 to build a ".
+ "CONFIG_RELCOATABLE kernel\n";
+}
/* We only have one iommu table on the mac for now, which makes
* things simple. Setup all PCI devices to point to this table
*/
- dev->dev.archdata.dma_data = &iommu_table_dart;
+ set_iommu_table_base(&dev->dev, &iommu_table_dart);
}
static void pci_dma_bus_setup_dart(struct pci_bus *bus)
}
#endif
+static inline int unrecoverable_excp(struct pt_regs *regs)
+{
+#ifdef CONFIG_4xx
+ /* We have no MSR_RI bit on 4xx, so we simply return false */
+ return 0;
+#else
+ return ((regs->msr & MSR_RI) == 0);
+#endif
+}
+
static int xmon_core(struct pt_regs *regs, int fromipi)
{
int cmd = 0;
bp = NULL;
if ((regs->msr & (MSR_IR|MSR_PR|MSR_SF)) == (MSR_IR|MSR_SF))
bp = at_breakpoint(regs->nip);
- if (bp || (regs->msr & MSR_RI) == 0)
+ if (bp || unrecoverable_excp(regs))
fromipi = 0;
if (!fromipi) {
cpu, BP_NUM(bp));
xmon_print_symbol(regs->nip, " ", ")\n");
}
- if ((regs->msr & MSR_RI) == 0)
+ if (unrecoverable_excp(regs))
printf("WARNING: exception is not recoverable, "
"can't continue\n");
release_output_lock();
printf("Stopped at breakpoint %x (", BP_NUM(bp));
xmon_print_symbol(regs->nip, " ", ")\n");
}
- if ((regs->msr & MSR_RI) == 0)
+ if (unrecoverable_excp(regs))
printf("WARNING: exception is not recoverable, "
"can't continue\n");
remove_bpts();
* /proc entries (sysctl)
*/
static const char appldata_proc_name[APPLDATA_PROC_NAME_LENGTH] = "appldata";
-static int appldata_timer_handler(ctl_table *ctl, int write, struct file *filp,
+static int appldata_timer_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos);
static int appldata_interval_handler(ctl_table *ctl, int write,
- struct file *filp,
void __user *buffer,
size_t *lenp, loff_t *ppos);
* Start/Stop timer, show status of timer (0 = not active, 1 = active)
*/
static int
-appldata_timer_handler(ctl_table *ctl, int write, struct file *filp,
+appldata_timer_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int len;
* current timer interval.
*/
static int
-appldata_interval_handler(ctl_table *ctl, int write, struct file *filp,
+appldata_interval_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int len, interval;
* monitoring (0 = not in process, 1 = in process)
*/
static int
-appldata_generic_handler(ctl_table *ctl, int write, struct file *filp,
+appldata_generic_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct appldata_ops *ops = NULL, *tmp_ops;
* if debug_active is already off
*/
static int
-s390dbf_procactive(ctl_table *table, int write, struct file *filp,
+s390dbf_procactive(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
if (!write || debug_stoppable || !debug_active)
- return proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ return proc_dointvec(table, write, buffer, lenp, ppos);
else
return 0;
}
static struct ctl_table cmm_table[];
static int
-cmm_pages_handler(ctl_table *ctl, int write, struct file *filp,
+cmm_pages_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
char buf[16], *p;
}
static int
-cmm_timeout_handler(ctl_table *ctl, int write, struct file *filp,
+cmm_timeout_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
char buf[64], *p;
struct sh_eth_plat_data sh_eth_plat = {
.phy = 0x1f, /* SMSC LAN8700 */
.edmac_endian = EDMAC_LITTLE_ENDIAN,
+ .ether_link_active_low = 1
};
static struct platform_device sh_eth_device = {
#include <linux/usb/r8a66597.h>
#include <video/sh_mobile_lcdc.h>
#include <media/sh_mobile_ceu.h>
+#include <sound/sh_fsi.h>
#include <asm/io.h>
#include <asm/heartbeat.h>
#include <asm/sh_eth.h>
},
};
+/* FSI */
+/*
+ * FSI-A use external clock which came from ak464x.
+ * So, we should change parent of fsi
+ */
+#define FCLKACR 0xa4150008
+static void fsimck_init(struct clk *clk)
+{
+ u32 status = ctrl_inl(clk->enable_reg);
+
+ /* use external clock */
+ status &= ~0x000000ff;
+ status |= 0x00000080;
+ ctrl_outl(status, clk->enable_reg);
+}
+
+static struct clk_ops fsimck_clk_ops = {
+ .init = fsimck_init,
+};
+
+static struct clk fsimcka_clk = {
+ .name = "fsimcka_clk",
+ .id = -1,
+ .ops = &fsimck_clk_ops,
+ .enable_reg = (void __iomem *)FCLKACR,
+ .rate = 0, /* unknown */
+};
+
+struct sh_fsi_platform_info fsi_info = {
+ .porta_flags = SH_FSI_BRS_INV |
+ SH_FSI_OUT_SLAVE_MODE |
+ SH_FSI_IN_SLAVE_MODE |
+ SH_FSI_OFMT(PCM) |
+ SH_FSI_IFMT(PCM),
+};
+
+static struct resource fsi_resources[] = {
+ [0] = {
+ .name = "FSI",
+ .start = 0xFE3C0000,
+ .end = 0xFE3C021d,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = 108,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device fsi_device = {
+ .name = "sh_fsi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(fsi_resources),
+ .resource = fsi_resources,
+ .dev = {
+ .platform_data = &fsi_info,
+ },
+};
+
/* KEYSC in SoC (Needs SW33-2 set to ON) */
static struct sh_keysc_info keysc_info = {
.mode = SH_KEYSC_MODE_1,
&sh_eth_device,
&sh7724_usb0_host_device,
&sh7724_usb1_gadget_device,
+ &fsi_device,
};
#define EEPROM_OP 0xBA206000
static int __init devices_setup(void)
{
u16 sw = ctrl_inw(SW4140); /* select camera, monitor */
+ struct clk *fsia_clk;
/* Reset Release */
ctrl_outw(ctrl_inw(FPGA_OUT) &
~((1 << 1) | /* LAN */
(1 << 6) | /* VIDEO DAC */
+ (1 << 7) | /* AK4643 */
(1 << 12) | /* USB0 */
(1 << 14)), /* RMII */
FPGA_OUT);
gpio_request(GPIO_FN_KEYOUT1, NULL);
gpio_request(GPIO_FN_KEYOUT0, NULL);
+ /* enable FSI */
+ gpio_request(GPIO_FN_FSIMCKB, NULL);
+ gpio_request(GPIO_FN_FSIMCKA, NULL);
+ gpio_request(GPIO_FN_FSIOASD, NULL);
+ gpio_request(GPIO_FN_FSIIABCK, NULL);
+ gpio_request(GPIO_FN_FSIIALRCK, NULL);
+ gpio_request(GPIO_FN_FSIOABCK, NULL);
+ gpio_request(GPIO_FN_FSIOALRCK, NULL);
+ gpio_request(GPIO_FN_CLKAUDIOAO, NULL);
+ gpio_request(GPIO_FN_FSIIBSD, NULL);
+ gpio_request(GPIO_FN_FSIOBSD, NULL);
+ gpio_request(GPIO_FN_FSIIBBCK, NULL);
+ gpio_request(GPIO_FN_FSIIBLRCK, NULL);
+ gpio_request(GPIO_FN_FSIOBBCK, NULL);
+ gpio_request(GPIO_FN_FSIOBLRCK, NULL);
+ gpio_request(GPIO_FN_CLKAUDIOBO, NULL);
+ gpio_request(GPIO_FN_FSIIASD, NULL);
+
+ /* change parent of FSI A */
+ fsia_clk = clk_get(NULL, "fsia_clk");
+ clk_register(&fsimcka_clk);
+ clk_set_parent(fsia_clk, &fsimcka_clk);
+ clk_set_rate(fsia_clk, 11000);
+ clk_set_rate(&fsimcka_clk, 11000);
+ clk_put(fsia_clk);
+
/*
* enable SH-Eth
*
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 16:04:11 2009
+# Linux kernel version: 2.6.31
+# Fri Sep 25 11:22:50 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
-# CONFIG_FREEZER is not set
+CONFIG_FREEZER=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
CONFIG_CPU_SUBTYPE_SH7723=y
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty1 console=ttySC5,38400 root=/dev/nfs ip=dhcp"
#
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_HIBERNATION is not set
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH_MOBILE=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_GPIO_SYSFS is not set
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
# CONFIG_REGULATOR is not set
CONFIG_MEDIA_SUPPORT=y
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
CONFIG_MMC_SPI=y
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:24:48 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:56:07 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
-# CONFIG_MARKERS is not set
# CONFIG_OPROFILE is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,115200 panic=3"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
# CONFIG_STANDALONE is not set
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_KEYBOARD_MAPLE=y
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_MAPLE=y
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc7
-# Tue Sep 8 13:56:18 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:56:41 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_NAMESPACES is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INITRAMFS_ROOT_UID=0
-CONFIG_INITRAMFS_ROOT_GID=0
CONFIG_RD_GZIP=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
-CONFIG_INITRAMFS_COMPRESSION_NONE=y
-# CONFIG_INITRAMFS_COMPRESSION_GZIP is not set
-# CONFIG_INITRAMFS_COMPRESSION_BZIP2 is not set
-# CONFIG_INITRAMFS_COMPRESSION_LZMA is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
-CONFIG_HAVE_PERF_COUNTERS=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
# CONFIG_USB_HWA_HCD is not set
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
# CONFIG_FSNOTIFY is not set
# CONFIG_DNOTIFY is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FTRACE_SYSCALLS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc7
-# Wed Aug 26 09:09:07 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:45:39 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
-CONFIG_HAVE_PERF_COUNTERS=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty0, console=ttySC0,115200 root=/dev/nfs ip=dhcp mem=120M memchunk.vpu=4m"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_KS8851 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_GPIO is not set
# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
CONFIG_KEYBOARD_SH_KEYSC=y
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_REGULATOR is not set
CONFIG_VIDEO_SH_MOBILE_CEU=y
# CONFIG_V4L_USB_DRIVERS is not set
CONFIG_RADIO_ADAPTERS=y
+# CONFIG_I2C_SI4713 is not set
+# CONFIG_RADIO_SI4713 is not set
# CONFIG_USB_DSBR is not set
-# CONFIG_USB_SI470X is not set
+# CONFIG_RADIO_SI470X is not set
# CONFIG_USB_MR800 is not set
# CONFIG_RADIO_TEA5764 is not set
# CONFIG_DAB is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
# CONFIG_USB_HWA_HCD is not set
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
CONFIG_MMC_SPI=y
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FTRACE_SYSCALLS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:25:35 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:57:13 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SYSVIPC is not set
# CONFIG_BSD_PROCESS_ACCT is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
# CONFIG_CGROUPS is not set
# CONFIG_EVENTFD is not set
CONFIG_SHMEM=y
# CONFIG_AIO is not set
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_BASE_SMALL=1
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_SPARSEMEM=y
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_R3964 is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:25:55 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:57:30 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION="_edosk7760"
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x02000000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="mem=64M console=ttySC2,115200 root=/dev/nfs rw nfsroot=192.168.0.3:/scripts/filesys ip=192.168.0.4"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
CONFIG_MTD=y
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=0
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH7760=y
# CONFIG_I2C_SH_MOBILE is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
CONFIG_I2C_DEBUG_CORE=y
CONFIG_I2C_DEBUG_ALGO=y
CONFIG_I2C_DEBUG_BUS=y
CONFIG_I2C_DEBUG_CHIP=y
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_UNUSED_SYMBOLS=y
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe80000
CONFIG_EARLY_PRINTK=y
-# CONFIG_DEBUG_BOOTMEM is not set
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_HASH=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:27:21 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:58:18 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
CONFIG_CPU_SUBTYPE_SH7763=y
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_MEMORY_HOTPLUG is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/nfs ip=bootp"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_PHYSMAP_COMPAT is not set
+# CONFIG_MTD_GPIO_ADDR is not set
# CONFIG_MTD_PLATRAM is not set
#
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:28:12 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 17:59:45 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
# CONFIG_SYSVIPC is not set
CONFIG_BSD_PROCESS_ACCT=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
CONFIG_SUSPEND_FREEZER=y
# CONFIG_HIBERNATION is not set
CONFIG_APM_EMULATION=y
+# CONFIG_PM_RUNTIME is not set
# CONFIG_CPU_IDLE is not set
# CONFIG_NET is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_ATA_SFF=y
# CONFIG_SATA_MV is not set
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_KEYBOARD_HP6XX=y
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_HP6XX=y
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_W90X900 is not set
# CONFIG_INPUT_MISC is not set
#
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
#
# Partition Types
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc6
-# Thu Aug 20 15:09:16 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:01:48 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_NAMESPACES is not set
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INITRAMFS_ROOT_UID=0
-CONFIG_INITRAMFS_ROOT_GID=0
CONFIG_RD_GZIP=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
-# CONFIG_INITRAMFS_COMPRESSION_NONE is not set
-CONFIG_INITRAMFS_COMPRESSION_GZIP=y
-# CONFIG_INITRAMFS_COMPRESSION_BZIP2 is not set
-# CONFIG_INITRAMFS_COMPRESSION_LZMA is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
CONFIG_ANON_INODES=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
-CONFIG_HAVE_PERF_COUNTERS=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
CONFIG_CPU_SUBTYPE_SH7724=y
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,115200 quiet"
#
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
# CONFIG_SUSPEND is not set
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FTRACE_SYSCALLS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc6
-# Thu Aug 20 21:58:52 2009
+# Linux kernel version: 2.6.31
+# Fri Sep 25 11:54:22 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
-CONFIG_HAVE_PERF_COUNTERS=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
CONFIG_CPU_SUBTYPE_SH7724=y
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty0 console=ttySC1,115200"
#
# CONFIG_PM_DEBUG is not set
# CONFIG_SUSPEND is not set
# CONFIG_HIBERNATION is not set
+CONFIG_PM_RUNTIME=y
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
# CONFIG_MTD_NAND is not set
-# CONFIG_MTD_ONENAND is not set
+CONFIG_MTD_ONENAND=y
+# CONFIG_MTD_ONENAND_VERIFY_WRITE is not set
+CONFIG_MTD_ONENAND_GENERIC=y
+# CONFIG_MTD_ONENAND_OTP is not set
+# CONFIG_MTD_ONENAND_2X_PROGRAM is not set
+# CONFIG_MTD_ONENAND_SIM is not set
#
# LPDDR flash memory drivers
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_GPIO is not set
# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_KEYBOARD_SUNKBD is not set
CONFIG_KEYBOARD_SH_KEYSC=y
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_AB3100_CORE is not set
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FTRACE_SYSCALLS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:28:45 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:05:49 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
# CONFIG_SCSI_DH is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FONT_8x16=y
CONFIG_SOUND=m
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
# CONFIG_SND is not set
CONFIG_SOUND_PRIME=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=m
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=m
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=m
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_UFS_FS=m
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_UFS_DEBUG is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:29:50 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:09:59 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,115200 root=/dev/sda1"
#
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:30:31 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:10:49 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
-# CONFIG_KMEMCHECK is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xa4430000
CONFIG_EARLY_PRINTK=y
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:31:56 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:14:35 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
# CONFIG_SYSVIPC is not set
# CONFIG_POSIX_MQUEUE is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
CONFIG_CPU_SUBTYPE_SH4_202=y
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/hda1"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 16:06:48 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:17:41 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
-# CONFIG_FREEZER is not set
+CONFIG_FREEZER=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty0 console=ttySC0,115200 earlyprintk=serial ip=on root=/dev/nfs ip=dhcp"
#
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_HIBERNATION is not set
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
CONFIG_KEYBOARD_SH_KEYSC=y
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH_MOBILE=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_GPIO_SYSFS is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
CONFIG_MEDIA_SUPPORT=y
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
# CONFIG_USB_GADGET_PXA27X is not set
# CONFIG_USB_GADGET_S3C_HSOTG is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
CONFIG_USB_GADGET_M66592=y
CONFIG_USB_M66592=y
-CONFIG_SUPERH_BUILT_IN_M66592=y
# CONFIG_USB_GADGET_AMD5536UDC is not set
# CONFIG_USB_GADGET_FSL_QE is not set
# CONFIG_USB_GADGET_CI13XXX is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe00000
CONFIG_EARLY_PRINTK=y
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:33:28 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:20:53 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,115200 root=/dev/mtdblock2 rootfstype=jffs2 mem=63M mtdparts=physmap-flash.0:0x00100000(bootloader)ro,0x00500000(Kernel)ro,0x00A00000(Filesystem)"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
CONFIG_DEBUG_SG=y
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
-# CONFIG_KMEMCHECK is not set
# CONFIG_SH_STANDARD_BIOS is not set
CONFIG_EARLY_SCIF_CONSOLE=y
-CONFIG_EARLY_SCIF_CONSOLE_PORT=0x00000000
+CONFIG_EARLY_SCIF_CONSOLE_PORT=0xa4000150
CONFIG_EARLY_PRINTK=y
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:34:44 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:24:31 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=m
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
CONFIG_CPU_SUBTYPE_SH7780=y
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_STP=m
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_PHYSMAP_COMPAT is not set
# CONFIG_MTD_PCI is not set
+# CONFIG_MTD_GPIO_ADDR is not set
# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
CONFIG_I2C_HIGHLANDER=y
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SH_MOBILE is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_THERMAL=y
# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_DISPLAY_SUPPORT is not set
CONFIG_SOUND=m
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
# CONFIG_SND is not set
CONFIG_SOUND_PRIME=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe00000
# CONFIG_EARLY_PRINTK is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:37:20 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:29:23 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-# CONFIG_CLASSIC_RCU is not set
-# CONFIG_TREE_RCU is not set
-CONFIG_PREEMPT_RCU=y
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
CONFIG_RCU_TRACE=y
-# CONFIG_TREE_RCU_TRACE is not set
-CONFIG_PREEMPT_RCU_TRACE=y
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+CONFIG_TREE_RCU_TRACE=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_MEMORY_HOTPLUG is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_STP=m
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
CONFIG_I2C_HIGHLANDER=y
# CONFIG_I2C_OCORES is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
# PCI GPIO expanders:
#
# CONFIG_GPIO_BT8XX is not set
+# CONFIG_GPIO_LANGWELL is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_LOGO is not set
CONFIG_SOUND=m
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
# CONFIG_SND is not set
CONFIG_SOUND_PRIME=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_KPROBES_SANITY_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
CONFIG_EARLY_PRINTK=y
-# CONFIG_DEBUG_BOOTMEM is not set
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_4KSTACKS=y
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:39:54 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:34:29 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_BSD_PROCESS_ACCT=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
# CONFIG_IKCONFIG_PROC is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
# CONFIG_AIO is not set
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
# CONFIG_SLUB is not set
CONFIG_SLOB=y
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 earlyprintk=serial ignore_loglevel"
#
#
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
+# CONFIG_PM_RUNTIME is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
# CONFIG_NET is not set
# CONFIG_SYS_HYPERVISOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
# CONFIG_FILE_LOCKING is not set
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
#
# Partition Types
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:40:44 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:35:04 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
# CONFIG_IKCONFIG_PROC is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
# CONFIG_SLUB is not set
CONFIG_SLOB=y
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 earlyprintk=serial ignore_loglevel"
#
#
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
+# CONFIG_PM_RUNTIME is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
CONFIG_MTD_REDBOOT_PARTS=y
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
# CONFIG_USB_HWA_HCD is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
-# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
CONFIG_MISC_FILESYSTEMS=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_LIST=y
CONFIG_DEBUG_SG=y
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xfffe8000
CONFIG_EARLY_PRINTK=y
-CONFIG_DEBUG_BOOTMEM=y
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:42:26 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:36:25 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty0 console=ttySC0,115200 root=/dev/sda1 earlyprintk=serial"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_ADCXX is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_LIS3_SPI is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
CONFIG_MFD_SM501=y
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_EZX_PCAP is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_LOGO_SUPERH_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
CONFIG_RTC_DRV_R9701=y
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe80000
CONFIG_EARLY_PRINTK=y
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:43:19 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:39:48 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_IO_TRAPPED=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty0 console=ttySC0,115200 root=/dev/sda1 earlyprintk=serial"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_MTD_PMC551 is not set
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_ADCXX is not set
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
# CONFIG_SENSORS_LIS3_SPI is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
CONFIG_MFD_SM501=y
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_EZX_PCAP is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_LOGO_SUPERH_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
CONFIG_RTC_DRV_R9701=y
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe80000
CONFIG_EARLY_PRINTK=y
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:43:54 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:40:25 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION="_SDK7780"
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=18
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_SLUB_DEBUG=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-CONFIG_LBD=y
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
CONFIG_CPU_SUBTYPE_SH7780=y
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x01800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="mem=128M console=tty0 console=ttySC0,115200 ip=bootp root=/dev/nfs nfsroot=192.168.0.1:/home/rootfs"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_PCMCIA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_MOUSE_PS2_ALPS=y
CONFIG_MOUSE_PS2_SYNAPTICS=y
CONFIG_MOUSE_PS2_TRACKPOINT=y
# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_SENTELIC is not set
# CONFIG_MOUSE_PS2_TOUCHKIT is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_POWER_SUPPLY_DEBUG is not set
# CONFIG_BATTERY_DS2760 is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_LOGO_SUPERH_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
# CONFIG_SND is not set
CONFIG_SOUND_PRIME=y
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_UNUSED_SYMBOLS=y
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_HASH=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:46:15 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:45:28 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
CONFIG_POSIX_MQUEUE=y
#
# RCU Subsystem
#
-# CONFIG_CLASSIC_RCU is not set
-# CONFIG_TREE_RCU is not set
-CONFIG_PREEMPT_RCU=y
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
CONFIG_RCU_TRACE=y
-# CONFIG_TREE_RCU_TRACE is not set
-CONFIG_PREEMPT_RCU_TRACE=y
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+CONFIG_TREE_RCU_TRACE=y
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
# CONFIG_SLUB is not set
CONFIG_SLOB=y
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC3,115200 ignore_loglevel earlyprintk=serial"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_CONFIGFS_FS=y
CONFIG_MISC_FILESYSTEMS=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_LIST=y
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_KGDB is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_HASH=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:47:07 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:46:55 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
# CONFIG_SHMEM is not set
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="deadline"
-# CONFIG_FREEZER is not set
+CONFIG_FREEZER=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200"
#
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MII=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH_MOBILE=y
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
# CONFIG_LOGO is not set
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
CONFIG_USB_DEVICEFS=y
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
# CONFIG_USB_OXU210HP_HCD is not set
CONFIG_USB_ISP116X_HCD=y
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_HWA_HCD is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffe00000
CONFIG_EARLY_PRINTK=y
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:47:56 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:50:05 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SYSVIPC is not set
# CONFIG_BSD_PROCESS_ACCT is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_BASE_SMALL=1
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_FS=y
CONFIG_PROC_SYSCTL=y
# CONFIG_SYSFS is not set
-# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
#
# Partition Types
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:48:18 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:50:52 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
# CONFIG_SYSVIPC is not set
# CONFIG_POSIX_MQUEUE is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:49:00 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:53:32 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
# CONFIG_SHMEM is not set
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_ATA_SFF=y
# CONFIG_SATA_MV is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
-# CONFIG_KMEMCHECK is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
# CONFIG_DUMP_CODE is not set
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:50:49 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:57:11 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
# CONFIG_SHMEM is not set
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda2"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_ATA_SFF=y
# CONFIG_SATA_MV is not set
# CONFIG_NET_ETHERNET is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
# CONFIG_NETWORK_FILESYSTEMS is not set
#
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
-# CONFIG_KMEMCHECK is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
# CONFIG_DUMP_CODE is not set
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 12:54:24 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:57:41 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
-# CONFIG_MARKERS is not set
# CONFIG_OPROFILE is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
-# CONFIG_FREEZER is not set
+CONFIG_FREEZER=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_HIBERNATION is not set
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_ATA_SFF=y
# CONFIG_SATA_MV is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Mon Jun 29 16:28:43 2009
+# Linux kernel version: 2.6.31
+# Fri Sep 25 11:50:59 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
-CONFIG_HAVE_PERF_COUNTERS=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
-# CONFIG_FREEZER is not set
+CONFIG_FREEZER=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
CONFIG_CPU_SUBTYPE_SH7724=y
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
#
CONFIG_SOLUTION_ENGINE=y
CONFIG_SH_7724_SOLUTION_ENGINE=y
+# CONFIG_SH_KFR2R09 is not set
+# CONFIG_SH_ECOVEC is not set
#
# Timer and clock configuration
#
# DMA support
#
-# CONFIG_SH_DMA is not set
+CONFIG_SH_DMA_API=y
+CONFIG_SH_DMA=y
+CONFIG_NR_ONCHIP_DMA_CHANNELS=12
+# CONFIG_NR_DMA_CHANNELS_BOOL is not set
#
# Companion Chips
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=tty1 console=ttySC3,115200 root=/dev/nfs ip=dhcp memchunk.vpu=4m"
#
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_HIBERNATION is not set
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
#
# CONFIG_MTD_DATAFLASH is not set
# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
CONFIG_KEYBOARD_SH_KEYSC=y
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH_MOBILE=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
# CONFIG_AB3100_CORE is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_REGULATOR is not set
CONFIG_VIDEO_V4L2_COMMON=y
# CONFIG_VIDEO_ALLOW_V4L1 is not set
CONFIG_VIDEO_V4L1_COMPAT=y
-# CONFIG_DVB_CORE is not set
-CONFIG_VIDEO_MEDIA=y
+CONFIG_DVB_CORE=m
+CONFIG_VIDEO_MEDIA=m
#
# Multimedia drivers
#
# CONFIG_MEDIA_ATTACH is not set
-CONFIG_MEDIA_TUNER=y
+CONFIG_MEDIA_TUNER=m
# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
-CONFIG_MEDIA_TUNER_SIMPLE=y
-CONFIG_MEDIA_TUNER_TDA8290=y
-CONFIG_MEDIA_TUNER_TDA9887=y
-CONFIG_MEDIA_TUNER_TEA5761=y
-CONFIG_MEDIA_TUNER_TEA5767=y
-CONFIG_MEDIA_TUNER_MT20XX=y
-CONFIG_MEDIA_TUNER_XC2028=y
-CONFIG_MEDIA_TUNER_XC5000=y
-CONFIG_MEDIA_TUNER_MC44S803=y
+CONFIG_MEDIA_TUNER_SIMPLE=m
+CONFIG_MEDIA_TUNER_TDA8290=m
+CONFIG_MEDIA_TUNER_TDA9887=m
+CONFIG_MEDIA_TUNER_TEA5761=m
+CONFIG_MEDIA_TUNER_TEA5767=m
+CONFIG_MEDIA_TUNER_MT20XX=m
+CONFIG_MEDIA_TUNER_XC2028=m
+CONFIG_MEDIA_TUNER_XC5000=m
+CONFIG_MEDIA_TUNER_MC44S803=m
CONFIG_VIDEO_V4L2=y
CONFIG_VIDEOBUF_GEN=y
CONFIG_VIDEOBUF_DMA_CONTIG=y
# CONFIG_VIDEO_VIVI is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
+# CONFIG_VIDEO_AU0828 is not set
CONFIG_SOC_CAMERA=y
# CONFIG_SOC_CAMERA_MT9M001 is not set
# CONFIG_SOC_CAMERA_MT9M111 is not set
CONFIG_USB_GSPCA=m
# CONFIG_USB_M5602 is not set
# CONFIG_USB_STV06XX is not set
+# CONFIG_USB_GL860 is not set
# CONFIG_USB_GSPCA_CONEX is not set
# CONFIG_USB_GSPCA_ETOMS is not set
# CONFIG_USB_GSPCA_FINEPIX is not set
+# CONFIG_USB_GSPCA_JEILINJ is not set
# CONFIG_USB_GSPCA_MARS is not set
# CONFIG_USB_GSPCA_MR97310A is not set
# CONFIG_USB_GSPCA_OV519 is not set
# CONFIG_USB_GSPCA_OV534 is not set
# CONFIG_USB_GSPCA_PAC207 is not set
# CONFIG_USB_GSPCA_PAC7311 is not set
+# CONFIG_USB_GSPCA_SN9C20X is not set
# CONFIG_USB_GSPCA_SONIXB is not set
# CONFIG_USB_GSPCA_SONIXJ is not set
# CONFIG_USB_GSPCA_SPCA500 is not set
# CONFIG_USB_STKWEBCAM is not set
# CONFIG_USB_S2255 is not set
# CONFIG_RADIO_ADAPTERS is not set
+CONFIG_DVB_MAX_ADAPTERS=8
+# CONFIG_DVB_DYNAMIC_MINORS is not set
+CONFIG_DVB_CAPTURE_DRIVERS=y
+# CONFIG_TTPCI_EEPROM is not set
+
+#
+# Supported USB Adapters
+#
+# CONFIG_DVB_USB is not set
+# CONFIG_SMS_SIANO_MDTV is not set
+
+#
+# Supported FlexCopII (B2C2) Adapters
+#
+# CONFIG_DVB_B2C2_FLEXCOP is not set
+
+#
+# Supported DVB Frontends
+#
+# CONFIG_DVB_FE_CUSTOMISE is not set
# CONFIG_DAB is not set
#
# CONFIG_LOGO_SUPERH_MONO is not set
# CONFIG_LOGO_SUPERH_VGA16 is not set
CONFIG_LOGO_SUPERH_CLUT224=y
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+# CONFIG_SOUND_OSS_CORE is not set
+CONFIG_SND=m
+CONFIG_SND_TIMER=m
+CONFIG_SND_PCM=m
+CONFIG_SND_JACK=y
+# CONFIG_SND_SEQUENCER is not set
+# CONFIG_SND_MIXER_OSS is not set
+# CONFIG_SND_PCM_OSS is not set
+# CONFIG_SND_DYNAMIC_MINORS is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_RAWMIDI_SEQ is not set
+# CONFIG_SND_OPL3_LIB_SEQ is not set
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_SPI is not set
+# CONFIG_SND_SUPERH is not set
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+CONFIG_SND_SOC=m
+
+#
+# SoC Audio support for SuperH
+#
+CONFIG_SND_SOC_SH4_FSI=m
+CONFIG_SND_FSI_AK4642=y
+CONFIG_SND_SOC_I2C_AND_SPI=m
+CONFIG_SND_SOC_ALL_CODECS=m
+CONFIG_SND_SOC_WM_HUBS=m
+CONFIG_SND_SOC_AD1836=m
+CONFIG_SND_SOC_AD1938=m
+CONFIG_SND_SOC_AD73311=m
+CONFIG_SND_SOC_AK4104=m
+CONFIG_SND_SOC_AK4535=m
+CONFIG_SND_SOC_AK4642=m
+CONFIG_SND_SOC_CS4270=m
+CONFIG_SND_SOC_L3=m
+CONFIG_SND_SOC_PCM3008=m
+CONFIG_SND_SOC_SPDIF=m
+CONFIG_SND_SOC_SSM2602=m
+CONFIG_SND_SOC_TLV320AIC23=m
+CONFIG_SND_SOC_TLV320AIC26=m
+CONFIG_SND_SOC_TLV320AIC3X=m
+CONFIG_SND_SOC_UDA134X=m
+CONFIG_SND_SOC_UDA1380=m
+CONFIG_SND_SOC_WM8510=m
+CONFIG_SND_SOC_WM8523=m
+CONFIG_SND_SOC_WM8580=m
+CONFIG_SND_SOC_WM8728=m
+CONFIG_SND_SOC_WM8731=m
+CONFIG_SND_SOC_WM8750=m
+CONFIG_SND_SOC_WM8753=m
+CONFIG_SND_SOC_WM8776=m
+CONFIG_SND_SOC_WM8900=m
+CONFIG_SND_SOC_WM8903=m
+CONFIG_SND_SOC_WM8940=m
+CONFIG_SND_SOC_WM8960=m
+CONFIG_SND_SOC_WM8961=m
+CONFIG_SND_SOC_WM8971=m
+CONFIG_SND_SOC_WM8974=m
+CONFIG_SND_SOC_WM8988=m
+CONFIG_SND_SOC_WM8990=m
+CONFIG_SND_SOC_WM8993=m
+CONFIG_SND_SOC_WM9081=m
+CONFIG_SND_SOC_MAX9877=m
+# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_USB_DEVICEFS is not set
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
#
# USB Device Class drivers
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
-# CONFIG_USB_GADGET is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+CONFIG_USB_GADGET_R8A66597=y
+CONFIG_USB_R8A66597=y
+# CONFIG_USB_GADGET_PXA27X is not set
+# CONFIG_USB_GADGET_S3C_HSOTG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_LANGWELL is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+CONFIG_USB_GADGET_DUALSPEED=y
+# CONFIG_USB_ZERO is not set
+# CONFIG_USB_AUDIO is not set
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+# CONFIG_USB_ETH_EEM is not set
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_USB_G_PRINTER is not set
+# CONFIG_USB_CDC_COMPOSITE is not set
#
# OTG and related infrastructure
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
CONFIG_MMC_SPI=y
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:00:01 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 18:58:58 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:02:26 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:01:41 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,38400"
#
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:03:56 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:03:59 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
+CONFIG_BLK_DEV_BSG=y
# CONFIG_BLK_DEV_INTEGRITY is not set
#
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
CONFIG_CPU_SUBTYPE_SH7780=y
CONFIG_SPARSEMEM=y
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00810000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
-CONFIG_CMDLINE="console=ttySC0.115200 root=/dev/sda1"
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
+CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/sda1"
#
# Bus options
# CONFIG_BT is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_NS87410 is not set
# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_PDC_OLD is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# A new alternative FireWire stack is available with EXPERIMENTAL=y
+# You can enable one or both FireWire driver stacks.
#
+
+#
+# See the help texts for more information.
+#
+# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
CONFIG_THERMAL=y
# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_LOGO_SUPERH_CLUT224=y
CONFIG_SOUND=y
CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
# CONFIG_SND is not set
CONFIG_SOUND_PRIME=y
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_NULL is not set
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:04:41 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:07:14 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=m
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,115200 mem=64M root=/dev/nfs"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
# CONFIG_FW_LOADER is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
# CONFIG_EARLY_PRINTK is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:06:13 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:11:49 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
# CONFIG_SHMEM is not set
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
# CONFIG_HID_PID is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_CONFIGFS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:06:48 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:14:00 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-# CONFIG_CLASSIC_RCU is not set
CONFIG_TREE_RCU=y
-# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
CONFIG_CPU_SUBTYPE_SH7724=y
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
#
# Memory hotplug is currently incompatible with Software Suspend
#
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
# Board support
#
# CONFIG_SH_7724_SOLUTION_ENGINE is not set
+# CONFIG_SH_KFR2R09 is not set
+# CONFIG_SH_ECOVEC is not set
#
# Timer and clock configuration
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
CONFIG_HIBERNATION_NVS=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
+CONFIG_PM_RUNTIME=y
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH_MOBILE=y
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:07:15 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:15:37 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
CONFIG_CPU_SUBTYPE_SH7763=y
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_MEMORY_HOTPLUG is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC2,115200 root=/dev/sda1 rootdelay=10"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AR7_PARTS is not set
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
# CONFIG_MTD_PHYSMAP_COMPAT is not set
+# CONFIG_MTD_GPIO_ADDR is not set
# CONFIG_MTD_PLATRAM is not set
#
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:08:05 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:17:16 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-# CONFIG_CLASSIC_RCU is not set
CONFIG_TREE_RCU=y
-# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=17
CONFIG_GROUP_SCHED=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
CONFIG_BASE_SMALL=0
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
CONFIG_CPU_SUBTYPE_SH7770=y
# CONFIG_CPU_SUBTYPE_SH7780 is not set
#
# Memory hotplug is currently incompatible with Software Suspend
#
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
CONFIG_HIBERNATION_NVS=y
CONFIG_HIBERNATION=y
CONFIG_PM_STD_PARTITION=""
+# CONFIG_PM_RUNTIME is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_IDLE_GOV_MENU=y
# CONFIG_TCG_TPM is not set
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
CONFIG_I2C_SH_MOBILE=y
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:08:29 2009
+# Linux kernel version: 2.6.31
+# Fri Sep 25 11:39:20 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
-CONFIG_IO_TRAPPED=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
-# CONFIG_POSIX_MQUEUE is not set
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_USER_SCHED=y
# CONFIG_CGROUP_SCHED is not set
# CONFIG_CGROUPS is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
-# CONFIG_KALLSYMS_ALL is not set
+CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+CONFIG_PERF_COUNTERS=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
-# CONFIG_MARKERS is not set
-# CONFIG_OPROFILE is not set
+CONFIG_TRACEPOINTS=y
+CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
-# CONFIG_KPROBES is not set
+CONFIG_KPROBES=y
+CONFIG_KRETPROBES=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+CONFIG_GCOV_KERNEL=y
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+# CONFIG_LBDAF is not set
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
# CONFIG_PAGE_SIZE_8KB is not set
# CONFIG_PAGE_SIZE_16KB is not set
# CONFIG_PAGE_SIZE_64KB is not set
+CONFIG_HUGETLB_PAGE_SIZE_64K=y
+# CONFIG_HUGETLB_PAGE_SIZE_256K is not set
+# CONFIG_HUGETLB_PAGE_SIZE_1MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_4MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_64MB is not set
+# CONFIG_HUGETLB_PAGE_SIZE_512MB is not set
CONFIG_SELECT_MEMORY_MODEL=y
# CONFIG_FLATMEM_MANUAL is not set
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_MEMORY_HOTPLUG is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
#
# CONFIG_SH_HIGHLANDER is not set
CONFIG_SH_SH7785LCR=y
+# CONFIG_SH_SH7785LCR_PT is not set
#
# Timer and clock configuration
CONFIG_SH_PCLK_FREQ=50000000
CONFIG_SH_CLK_CPG=y
CONFIG_TICK_ONESHOT=y
-# CONFIG_NO_HZ is not set
+CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
#
# CPU Frequency scaling
#
-# CONFIG_CPU_FREQ is not set
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+# CONFIG_CPU_FREQ_DEBUG is not set
+CONFIG_CPU_FREQ_STAT=y
+CONFIG_CPU_FREQ_STAT_DETAILS=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+CONFIG_SH_CPU_FREQ=y
#
# DMA support
CONFIG_SCHED_HRTICK=y
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
-# CONFIG_SECCOMP is not set
+CONFIG_SECCOMP=y
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_GUSA=y
-# CONFIG_SPARSE_IRQ is not set
+CONFIG_SPARSE_IRQ=y
#
# Boot options
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
CONFIG_SH_PCIDMA_NONCOHERENT=y
# CONFIG_PCIEPORTBUS is not set
# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_PCI_LEGACY=y
-# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCI_LEGACY is not set
# CONFIG_PCI_STUB is not set
# CONFIG_PCI_IOV is not set
# CONFIG_PCCARD is not set
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
-# CONFIG_CPU_IDLE is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+# CONFIG_HIBERNATION is not set
+# CONFIG_PM_RUNTIME is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_IDLE_GOV_MENU=y
CONFIG_NET=y
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Network testing
#
# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_TCPPROBE is not set
+# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
-# CONFIG_DEBUG_DRIVER is not set
-# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_SCSI_DMA=y
# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
#
# SCSI support type (disk, tape, CD-ROM)
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_JME is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
-# CONFIG_WLAN_PRE80211 is not set
-# CONFIG_WLAN_80211 is not set
+# CONFIG_WLAN is not set
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_EVDEV is not set
-# CONFIG_INPUT_EVBUG is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=m
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
-# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_ADP5588 is not set
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
-# CONFIG_INPUT_MOUSE is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_SENTELIC is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
+# CONFIG_MOUSE_BCM5974 is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_SYNAPTICS_I2C is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
#
# Hardware I/O ports
#
-# CONFIG_SERIO is not set
+CONFIG_SERIO=y
+CONFIG_SERIO_I8042=y
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SERIO_PCIPS2 is not set
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
#
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_DEVKMEM=y
+# CONFIG_DEVKMEM is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NOZOMI is not set
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
-# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
-CONFIG_LEGACY_PTYS=y
-CONFIG_LEGACY_PTY_COUNT=256
+CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
+# CONFIG_LEGACY_PTYS is not set
# CONFIG_IPMI_HANDLER is not set
-CONFIG_HW_RANDOM=y
-# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_HW_RANDOM is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_RAW_DRIVER is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_ALGOPCA=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SH_MOBILE is not set
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
-# CONFIG_WATCHDOG is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+# CONFIG_ALIM7101_WDT is not set
+CONFIG_SH_WDT=y
+# CONFIG_SH_WDT_MMAP is not set
+
+#
+# PCI-based Watchdog Cards
+#
+# CONFIG_PCIPCWATCHDOG is not set
+# CONFIG_WDTPCI is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+# CONFIG_VGA_ARB is not set
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
-CONFIG_FB_SYS_FILLRECT=m
-CONFIG_FB_SYS_COPYAREA=m
-CONFIG_FB_SYS_IMAGEBLIT=m
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
# CONFIG_FB_FOREIGN_ENDIAN is not set
-CONFIG_FB_SYS_FOPS=m
-CONFIG_FB_DEFERRED_IO=y
+# CONFIG_FB_SYS_FOPS is not set
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_CARMINE is not set
-CONFIG_FB_SH_MOBILE_LCDC=m
+# CONFIG_FB_SH_MOBILE_LCDC is not set
CONFIG_FB_SM501=y
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FB_METRONOME is not set
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_LOGO_LINUX_CLUT224=y
-# CONFIG_LOGO_SUPERH_MONO is not set
-# CONFIG_LOGO_SUPERH_VGA16 is not set
-# CONFIG_LOGO_SUPERH_CLUT224 is not set
-# CONFIG_SOUND is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+CONFIG_LOGO_SUPERH_MONO=y
+CONFIG_LOGO_SUPERH_VGA16=y
+CONFIG_LOGO_SUPERH_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_HWDEP=y
+CONFIG_SND_RAWMIDI=y
+CONFIG_SND_SEQUENCER=y
+# CONFIG_SND_SEQ_DUMMY is not set
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_HRTIMER=y
+CONFIG_SND_SEQ_HRTIMER_DEFAULT=y
+CONFIG_SND_DYNAMIC_MINORS=y
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+CONFIG_SND_RAWMIDI_SEQ=y
+CONFIG_SND_OPL3_LIB_SEQ=y
+# CONFIG_SND_OPL4_LIB_SEQ is not set
+# CONFIG_SND_SBAWE_SEQ is not set
+# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_MPU401_UART=y
+CONFIG_SND_OPL3_LIB=y
+# CONFIG_SND_DRIVERS is not set
+CONFIG_SND_PCI=y
+# CONFIG_SND_AD1889 is not set
+# CONFIG_SND_ALS300 is not set
+# CONFIG_SND_ALI5451 is not set
+# CONFIG_SND_ATIIXP is not set
+# CONFIG_SND_ATIIXP_MODEM is not set
+# CONFIG_SND_AU8810 is not set
+# CONFIG_SND_AU8820 is not set
+# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AW2 is not set
+# CONFIG_SND_AZT3328 is not set
+# CONFIG_SND_BT87X is not set
+# CONFIG_SND_CA0106 is not set
+CONFIG_SND_CMIPCI=y
+# CONFIG_SND_OXYGEN is not set
+# CONFIG_SND_CS4281 is not set
+# CONFIG_SND_CS46XX is not set
+# CONFIG_SND_CTXFI is not set
+# CONFIG_SND_DARLA20 is not set
+# CONFIG_SND_GINA20 is not set
+# CONFIG_SND_LAYLA20 is not set
+# CONFIG_SND_DARLA24 is not set
+# CONFIG_SND_GINA24 is not set
+# CONFIG_SND_LAYLA24 is not set
+# CONFIG_SND_MONA is not set
+# CONFIG_SND_MIA is not set
+# CONFIG_SND_ECHO3G is not set
+# CONFIG_SND_INDIGO is not set
+# CONFIG_SND_INDIGOIO is not set
+# CONFIG_SND_INDIGODJ is not set
+# CONFIG_SND_INDIGOIOX is not set
+# CONFIG_SND_INDIGODJX is not set
+# CONFIG_SND_EMU10K1 is not set
+# CONFIG_SND_EMU10K1X is not set
+# CONFIG_SND_ENS1370 is not set
+# CONFIG_SND_ENS1371 is not set
+# CONFIG_SND_ES1938 is not set
+# CONFIG_SND_ES1968 is not set
+# CONFIG_SND_FM801 is not set
+# CONFIG_SND_HDA_INTEL is not set
+# CONFIG_SND_HDSP is not set
+# CONFIG_SND_HDSPM is not set
+# CONFIG_SND_HIFIER is not set
+# CONFIG_SND_ICE1712 is not set
+# CONFIG_SND_ICE1724 is not set
+# CONFIG_SND_INTEL8X0 is not set
+# CONFIG_SND_INTEL8X0M is not set
+# CONFIG_SND_KORG1212 is not set
+# CONFIG_SND_LX6464ES is not set
+# CONFIG_SND_MAESTRO3 is not set
+# CONFIG_SND_MIXART is not set
+# CONFIG_SND_NM256 is not set
+# CONFIG_SND_PCXHR is not set
+# CONFIG_SND_RIPTIDE is not set
+# CONFIG_SND_RME32 is not set
+# CONFIG_SND_RME96 is not set
+# CONFIG_SND_RME9652 is not set
+# CONFIG_SND_SONICVIBES is not set
+# CONFIG_SND_TRIDENT is not set
+# CONFIG_SND_VIA82XX is not set
+# CONFIG_SND_VIA82XX_MODEM is not set
+# CONFIG_SND_VIRTUOSO is not set
+# CONFIG_SND_VX222 is not set
+# CONFIG_SND_YMFPCI is not set
+# CONFIG_SND_SUPERH is not set
+CONFIG_SND_USB=y
+# CONFIG_SND_USB_AUDIO is not set
+# CONFIG_SND_USB_CAIAQ is not set
+# CONFIG_SND_SOC is not set
+# CONFIG_SOUND_PRIME is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
#
# Special HID drivers
#
-CONFIG_HID_A4TECH=y
-CONFIG_HID_APPLE=y
-CONFIG_HID_BELKIN=y
-CONFIG_HID_CHERRY=y
-CONFIG_HID_CHICONY=y
-CONFIG_HID_CYPRESS=y
-# CONFIG_HID_DRAGONRISE is not set
-CONFIG_HID_EZKEY=y
-# CONFIG_HID_KYE is not set
-CONFIG_HID_GYRATION=y
-# CONFIG_HID_KENSINGTON is not set
-CONFIG_HID_LOGITECH=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+# CONFIG_DRAGONRISE_FF is not set
+CONFIG_HID_EZKEY=m
+CONFIG_HID_KYE=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LOGITECH=m
# CONFIG_LOGITECH_FF is not set
# CONFIG_LOGIRUMBLEPAD2_FF is not set
-CONFIG_HID_MICROSOFT=y
-CONFIG_HID_MONTEREY=y
-# CONFIG_HID_NTRIG is not set
-CONFIG_HID_PANTHERLORD=y
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_PANTHERLORD=m
# CONFIG_PANTHERLORD_FF is not set
-CONFIG_HID_PETALYNX=y
-CONFIG_HID_SAMSUNG=y
-CONFIG_HID_SONY=y
-CONFIG_HID_SUNPLUS=y
-# CONFIG_HID_GREENASIA is not set
-# CONFIG_HID_SMARTJOYPLUS is not set
-# CONFIG_HID_TOPSEED is not set
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_SMARTJOYPLUS=m
+# CONFIG_SMARTJOYPLUS_FF is not set
+CONFIG_HID_TOPSEED=m
# CONFIG_HID_THRUSTMASTER is not set
-# CONFIG_HID_ZEROPLUS is not set
+CONFIG_HID_ZEROPLUS=m
+# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
#
# Miscellaneous USB options
#
-CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICEFS is not set
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
-CONFIG_USB_MON=y
+# CONFIG_USB_MON is not set
# CONFIG_USB_WUSB is not set
# CONFIG_USB_WUSB_CBAF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
-CONFIG_USB_OHCI_HCD=m
-# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
-# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
-CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_ISP1362_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
-CONFIG_USB_TEST=m
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
#
# CONFIG_NOP_USB_XCEIV is not set
# CONFIG_UWB is not set
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_SDHCI=m
+# CONFIG_MMC_SDHCI_PCI is not set
+CONFIG_MMC_SDHCI_PLTFM=m
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
+# CONFIG_MMC_TIFM_SD is not set
+# CONFIG_MMC_CB710 is not set
+# CONFIG_MMC_VIA_SDMMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
#
# CONFIG_RTC_DRV_SH is not set
# CONFIG_RTC_DRV_GENERIC is not set
-# CONFIG_DMADEVICES is not set
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
# CONFIG_AUXDISPLAY is not set
-# CONFIG_UIO is not set
+CONFIG_UIO=m
+# CONFIG_UIO_CIF is not set
+# CONFIG_UIO_PDRV is not set
+# CONFIG_UIO_PDRV_GENIRQ is not set
+# CONFIG_UIO_SMX is not set
+# CONFIG_UIO_AEC is not set
+# CONFIG_UIO_SERCOS3 is not set
+# CONFIG_UIO_PCI_GENERIC is not set
#
# TI VLYNQ
# CONFIG_EXT3_FS_SECURITY is not set
# CONFIG_EXT4_FS is not set
CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
-CONFIG_FS_POSIX_ACL=y
+# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
-# CONFIG_HUGETLBFS is not set
-# CONFIG_HUGETLB_PAGE is not set
-# CONFIG_CONFIGFS_FS is not set
+CONFIG_HUGETLBFS=y
+CONFIG_HUGETLB_PAGE=y
+CONFIG_CONFIGFS_FS=y
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
-CONFIG_NFSD=y
+CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
-CONFIG_NFSD_V4=y
+# CONFIG_NFSD_V4 is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
-CONFIG_EXPORTFS=y
+CONFIG_EXPORTFS=m
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
CONFIG_SUNRPC_GSS=y
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
-# CONFIG_PRINTK_TIME is not set
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
+CONFIG_PRINTK_TIME=y
+CONFIG_ENABLE_WARN_DEPRECATED=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
-# CONFIG_MAGIC_SYSRQ is not set
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_SHIRQ is not set
-CONFIG_DETECT_SOFTLOCKUP=y
-# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
-CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
-CONFIG_DETECT_HUNG_TASK=y
-# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
-CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_DEBUG_KERNEL is not set
CONFIG_SCHED_DEBUG=y
-# CONFIG_SCHEDSTATS is not set
-# CONFIG_TIMER_STATS is not set
-# CONFIG_DEBUG_OBJECTS is not set
-# CONFIG_DEBUG_SLAB is not set
-CONFIG_DEBUG_PREEMPT=y
-# CONFIG_DEBUG_RT_MUTEXES is not set
-# CONFIG_RT_MUTEX_TESTER is not set
-# CONFIG_DEBUG_SPINLOCK is not set
-# CONFIG_DEBUG_MUTEXES is not set
-# CONFIG_DEBUG_LOCK_ALLOC is not set
-# CONFIG_PROVE_LOCKING is not set
-# CONFIG_LOCK_STAT is not set
-# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
-# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
-# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_SCHEDSTATS=y
+CONFIG_TRACE_IRQFLAGS=y
+CONFIG_STACKTRACE=y
# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_VM is not set
-# CONFIG_DEBUG_WRITECOUNT is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
-# CONFIG_DEBUG_LIST is not set
-# CONFIG_DEBUG_SG is not set
-# CONFIG_DEBUG_NOTIFIERS is not set
-# CONFIG_FRAME_POINTER is not set
-# CONFIG_RCU_TORTURE_TEST is not set
+CONFIG_FRAME_POINTER=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
-# CONFIG_BACKTRACE_SELF_TEST is not set
-# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
-# CONFIG_FAULT_INJECTION is not set
-# CONFIG_LATENCYTOP is not set
+CONFIG_LATENCYTOP=y
CONFIG_SYSCTL_SYSCALL_CHECK=y
-# CONFIG_PAGE_POISONING is not set
+CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_TRACER_MAX_TRACE=y
+CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
+CONFIG_TRACING=y
+CONFIG_GENERIC_TRACER=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
+CONFIG_FUNCTION_TRACER=y
+CONFIG_FUNCTION_GRAPH_TRACER=y
+CONFIG_IRQSOFF_TRACER=y
# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+CONFIG_SCHED_TRACER=y
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_PROFILE_ALL_BRANCHES is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
+CONFIG_STACK_TRACER=y
+CONFIG_KMEMTRACE=y
+CONFIG_WORKQUEUE_TRACER=y
# CONFIG_BLK_DEV_IO_TRACE is not set
+CONFIG_DYNAMIC_FTRACE=y
+# CONFIG_FUNCTION_PROFILER is not set
+CONFIG_FTRACE_MCOUNT_RECORD=y
+# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_RING_BUFFER_BENCHMARK is not set
+# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
-# CONFIG_KGDB is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
-# CONFIG_DEBUG_STACK_USAGE is not set
-# CONFIG_4KSTACKS is not set
-# CONFIG_DUMP_CODE is not set
-# CONFIG_SH_NO_BSS_INIT is not set
+CONFIG_DWARF_UNWINDER=y
+CONFIG_MCOUNT=y
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
# CONFIG_CRYPTO_HW is not set
-# CONFIG_BINARY_PRINTF is not set
+CONFIG_BINARY_PRINTF=y
#
# Library routines
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:09:34 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:23:18 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
-CONFIG_IO_TRAPPED=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
-# CONFIG_MARKERS is not set
# CONFIG_OPROFILE is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_JME is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_ALGOPCA=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SH_MOBILE is not set
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
CONFIG_NFSD=y
CONFIG_NFSD_V3=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_KGDB is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
# CONFIG_DUMP_CODE is not set
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:10:33 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:27:17 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
# CONFIG_SWAP is not set
# CONFIG_SYSVIPC is not set
# CONFIG_POSIX_MQUEUE is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
# CONFIG_SHMEM is not set
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
# CONFIG_SLUB is not set
CONFIG_SLOB=y
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_BASE_SMALL=1
# CONFIG_MODULES is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00210000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,115200 root=1f01 mtdparts=phys_mapped_flash:64k(firm)ro,-(sys) netdev=34,0x300,eth0 "
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_KS8842 is not set
CONFIG_NETDEV_1000=y
CONFIG_NETDEV_10000=y
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_PROC_SYSCTL=y
CONFIG_PROC_PAGE_MONITOR=y
# CONFIG_SYSFS is not set
-CONFIG_TMPFS=y
-# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
CONFIG_EARLY_PRINTK=y
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:11:03 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:29:26 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-# CONFIG_CLASSIC_RCU is not set
-# CONFIG_TREE_RCU is not set
-CONFIG_PREEMPT_RCU=y
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
CONFIG_RCU_TRACE=y
-# CONFIG_TREE_RCU_TRACE is not set
-CONFIG_PREEMPT_RCU_TRACE=y
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
+CONFIG_TREE_RCU_TRACE=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+CONFIG_EVENT_PROFILE=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
# CONFIG_SLUB is not set
CONFIG_SLOB=y
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_USE_GENERIC_SMP_HELPERS=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_STOP_MACHINE=y
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00010000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00010000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 earlyprintk=bios ignore_loglevel"
#
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_ATA_SFF=y
# CONFIG_SATA_MV is not set
# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
# CONFIG_B44 is not set
# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_TCG_TPM is not set
CONFIG_I2C=m
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SH_MOBILE is not set
# CONFIG_I2C_SIMTEC is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_TMIO is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
# CONFIG_REGULATOR is not set
# CONFIG_MEDIA_SUPPORT is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=m
# CONFIG_USB_HWA_HCD is not set
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
CONFIG_USB_GADGET=y
# CONFIG_USB_GADGET_LH7A40X is not set
# CONFIG_USB_GADGET_OMAP is not set
# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_R8A66597 is not set
# CONFIG_USB_GADGET_PXA27X is not set
# CONFIG_USB_GADGET_S3C_HSOTG is not set
-# CONFIG_USB_GADGET_S3C2410 is not set
# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_S3C2410 is not set
CONFIG_USB_GADGET_M66592=y
CONFIG_USB_M66592=y
# CONFIG_USB_GADGET_AMD5536UDC is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_KPROBES_SANITY_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_RING_BUFFER=y
CONFIG_EVENT_TRACING=y
CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_PREEMPT_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
CONFIG_SH_STANDARD_BIOS=y
# CONFIG_EARLY_SCIF_CONSOLE is not set
CONFIG_EARLY_PRINTK=y
-# CONFIG_DEBUG_BOOTMEM is not set
-CONFIG_DEBUG_STACKOVERFLOW=y
+# CONFIG_STACK_DEBUG is not set
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
# CONFIG_CRYPTO_MANAGER is not set
# CONFIG_CRYPTO_MANAGER2 is not set
# CONFIG_CRYPTO_GF128MUL is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.31-rc6
-# Thu Aug 20 15:03:04 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:33:00 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
-CONFIG_HAVE_PERF_COUNTERS=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_KPROBES=y
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
# CONFIG_WIRELESS_EXT is not set
# CONFIG_LIB80211 is not set
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
# CONFIG_DNOTIFY is not set
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FTRACE_SYSCALLS=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:12:28 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:35:03 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
# CONFIG_SYSVIPC is not set
# CONFIG_BSD_PROCESS_ACCT is not set
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
#
# Partition Types
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_LATENCYTOP is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:12:54 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:36:36 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
# CONFIG_PROFILING is not set
-# CONFIG_MARKERS is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_BOOT_LINK_OFFSET=0x009e0000
CONFIG_ENTRY_OFFSET=0x00001000
# CONFIG_UBC_WAKEUP is not set
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC1,38400N81 root=/dev/nfs ip=:::::eth1:autoconf rw"
#
# CONFIG_BRIDGE_NF_EBTABLES is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
CONFIG_STP=y
CONFIG_FIB_RULES=y
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=m
CONFIG_MTD=m
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=0
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
# CONFIG_MTD_PARTITIONS is not set
-# CONFIG_MTD_TESTS is not set
#
# User Modules And Translation Layers
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_SFC is not set
# CONFIG_BE2NET is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_I5K_AMB is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
CONFIG_WATCHDOG=y
# CONFIG_WATCHDOG_NOWAYOUT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_XFS_POSIX_ACL is not set
# CONFIG_XFS_RT is not set
# CONFIG_XFS_DEBUG is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_ROMFS_ON_BLOCK=y
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
CONFIG_FTRACE=y
# CONFIG_FUNCTION_TRACER is not set
# CONFIG_IRQSOFF_TRACER is not set
# CONFIG_SCHED_TRACER is not set
# CONFIG_ENABLE_DEFAULT_TRACERS is not set
+# CONFIG_FTRACE_SYSCALLS is not set
# CONFIG_BOOT_TRACER is not set
CONFIG_BRANCH_PROFILE_NONE=y
# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_KGDB is not set
-# CONFIG_KMEMCHECK is not set
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
# CONFIG_DUMP_CODE is not set
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_GHASH is not set
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:14:36 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:42:33 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
# CONFIG_GENERIC_GPIO is not set
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_SLUB_DEBUG=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
-# CONFIG_MARKERS is not set
# CONFIG_OPROFILE is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_DEFAULT_CFQ is not set
CONFIG_DEFAULT_NOOP=y
CONFIG_DEFAULT_IOSCHED="noop"
-# CONFIG_FREEZER is not set
+CONFIG_FREEZER=y
#
# System type
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE_OVERWRITE=y
+# CONFIG_CMDLINE_EXTEND is not set
CONFIG_CMDLINE="console=ttySC0,115200 root=/dev/nfs ip=dhcp"
#
#
# Power management options (EXPERIMENTAL)
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+# CONFIG_HIBERNATION is not set
+CONFIG_PM_RUNTIME=y
# CONFIG_CPU_IDLE is not set
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
CONFIG_CFG80211=y
+# CONFIG_NL80211_TESTMODE is not set
+# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
# CONFIG_CFG80211_REG_DEBUG is not set
+CONFIG_CFG80211_DEFAULT_PS=y
+CONFIG_CFG80211_DEFAULT_PS_VALUE=1
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
CONFIG_LIB80211=m
# CONFIG_LIB80211_DEBUG is not set
CONFIG_MAC80211=y
-CONFIG_MAC80211_DEFAULT_PS=y
-CONFIG_MAC80211_DEFAULT_PS_VALUE=1
-
-#
-# Rate control algorithm selection
-#
CONFIG_MAC80211_RC_PID=y
# CONFIG_MAC80211_RC_MINSTREL is not set
CONFIG_MAC80211_RC_DEFAULT_PID=y
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_BNX2_ISCSI is not set
# CONFIG_LIBFC is not set
# CONFIG_LIBFCOE is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_ATA_SFF=y
# CONFIG_SATA_MV is not set
# CONFIG_KS8842 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
CONFIG_LIBERTAS=m
# CONFIG_RTL8187 is not set
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_P54_COMMON is not set
-# CONFIG_AR9170_USB is not set
+# CONFIG_ATH_COMMON is not set
# CONFIG_HOSTAP is not set
# CONFIG_B43 is not set
# CONFIG_B43LEGACY is not set
# CONFIG_ZD1211RW is not set
# CONFIG_RT2X00 is not set
+# CONFIG_WL12XX is not set
# CONFIG_IWM is not set
#
# CONFIG_TCG_TPM is not set
# CONFIG_I2C is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_F71882FG is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_USB_DEVICEFS is not set
CONFIG_USB_DEVICE_CLASS=y
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
# CONFIG_USB_OTG_WHITELIST is not set
# CONFIG_USB_OTG_BLACKLIST_HUB is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_SL811_HCD is not set
CONFIG_USB_R8A66597_HCD=y
-# CONFIG_SUPERH_ON_CHIP_R8A66597 is not set
# CONFIG_USB_HWA_HCD is not set
#
# CONFIG_USB_LD is not set
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
# CONFIG_USB_ISIGHTFW is not set
# CONFIG_USB_VST is not set
# CONFIG_USB_GADGET is not set
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_HEADERS_CHECK is not set
# CONFIG_LATENCYTOP is not set
# CONFIG_SYSCTL_SYSCALL_CHECK is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DMA_API_DEBUG is not set
CONFIG_HAVE_ARCH_KGDB=y
# CONFIG_SH_STANDARD_BIOS is not set
# CONFIG_EARLY_SCIF_CONSOLE is not set
+# CONFIG_DWARF_UNWINDER is not set
#
# Security options
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
CONFIG_CRYPTO_MICHAEL_MIC=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30
-# Thu Jun 18 13:15:28 2009
+# Linux kernel version: 2.6.31
+# Thu Sep 24 19:46:13 2009
#
CONFIG_SUPERH=y
CONFIG_SUPERH32=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_IRQ_PER_CPU=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
# CONFIG_ARCH_SUSPEND_POSSIBLE is not set
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_SYS_SUPPORTS_SMP=y
CONFIG_SYS_SUPPORTS_NUMA=y
CONFIG_SYS_SUPPORTS_PCI=y
CONFIG_SYS_SUPPORTS_TMU=y
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_ARCH_NO_VIRT_TO_BUS=y
CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
+CONFIG_HAVE_KERNEL_GZIP=y
+CONFIG_HAVE_KERNEL_BZIP2=y
+CONFIG_HAVE_KERNEL_LZMA=y
+CONFIG_KERNEL_GZIP=y
+# CONFIG_KERNEL_BZIP2 is not set
+# CONFIG_KERNEL_LZMA is not set
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSVIPC_SYSCTL=y
#
# RCU Subsystem
#
-# CONFIG_CLASSIC_RCU is not set
CONFIG_TREE_RCU=y
-# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_PREEMPT_RCU is not set
# CONFIG_RCU_TRACE is not set
CONFIG_RCU_FANOUT=32
# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+CONFIG_HAVE_PERF_EVENTS=y
#
-# Performance Counters
+# Kernel Performance Events And Counters
#
+CONFIG_PERF_EVENTS=y
+# CONFIG_PERF_COUNTERS is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_COMPAT_BRK=y
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
-CONFIG_TRACEPOINTS=y
-CONFIG_MARKERS=y
# CONFIG_OPROFILE is not set
CONFIG_HAVE_OPROFILE=y
# CONFIG_KPROBES is not set
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_DMA_API_DEBUG=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_CPU_SUBTYPE_SH4_202 is not set
# CONFIG_CPU_SUBTYPE_SH7723 is not set
# CONFIG_CPU_SUBTYPE_SH7724 is not set
+# CONFIG_CPU_SUBTYPE_SH7757 is not set
# CONFIG_CPU_SUBTYPE_SH7763 is not set
# CONFIG_CPU_SUBTYPE_SH7770 is not set
# CONFIG_CPU_SUBTYPE_SH7780 is not set
CONFIG_HAVE_MEMORY_PRESENT=y
CONFIG_SPARSEMEM_STATIC=y
# CONFIG_MEMORY_HOTPLUG is not set
-CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
CONFIG_MIGRATION=y
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_NR_QUICK=2
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
#
CONFIG_KEXEC=y
# CONFIG_CRASH_DUMP is not set
CONFIG_SECCOMP=y
+# CONFIG_SMP is not set
CONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
CONFIG_ZERO_PAGE_OFFSET=0x00001000
CONFIG_BOOT_LINK_OFFSET=0x00800000
CONFIG_ENTRY_OFFSET=0x00001000
-# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_CMDLINE_OVERWRITE is not set
+# CONFIG_CMDLINE_EXTEND is not set
#
# Bus options
# CONFIG_SH_PCIDMA_NONCOHERENT is not set
CONFIG_PCIEPORTBUS=y
CONFIG_PCIEAER=y
+# CONFIG_PCIE_ECRC is not set
+# CONFIG_PCIEAER_INJECT is not set
CONFIG_PCIEASPM=y
CONFIG_PCIEASPM_DEBUG=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
# CONFIG_HIBERNATION is not set
+# CONFIG_PM_RUNTIME is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# Network testing
#
# CONFIG_NET_PKTGEN is not set
-# CONFIG_NET_DROP_MONITOR is not set
# CONFIG_HAMRADIO is not set
# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
#
# CFG80211 needs to be enabled for MAC80211
#
-CONFIG_MAC80211_DEFAULT_PS_VALUE=0
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
# CONFIG_MTD_AR7_PARTS is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
CONFIG_SATA_SIL24=y
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_ATL1E is not set
# CONFIG_JME is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_SH_KEYSC is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_COMPAT=y
# CONFIG_I2C_CHARDEV is not set
CONFIG_I2C_HELPER_AUTO=y
CONFIG_I2C_ALGOPCA=y
#
# I2C system bus drivers (mostly embedded / system-on-chip)
#
+# CONFIG_I2C_DESIGNWARE is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_SH_MOBILE is not set
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
CONFIG_ARCH_REQUIRE_GPIOLIB=y
CONFIG_GPIOLIB=y
# CONFIG_DEBUG_GPIO is not set
# PCI GPIO expanders:
#
# CONFIG_GPIO_BT8XX is not set
+# CONFIG_GPIO_LANGWELL is not set
#
# SPI GPIO expanders:
#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_THMC50 is not set
# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-CONFIG_THERMAL_HWMON=y
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
# CONFIG_MFD_TMIO is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
+# CONFIG_AB3100_CORE is not set
# CONFIG_REGULATOR is not set
CONFIG_MEDIA_SUPPORT=y
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_EZKEY=y
# CONFIG_HID_KYE is not set
CONFIG_HID_GYRATION=y
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
# CONFIG_RTC_DRV_S35390A is not set
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
CONFIG_EXT4_FS_XATTR=y
# CONFIG_EXT4_FS_POSIX_ACL is not set
# CONFIG_EXT4_FS_SECURITY is not set
+# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=y
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
CONFIG_BTRFS_FS=y
# CONFIG_BTRFS_FS_POSIX_ACL is not set
+# CONFIG_NILFS2_FS is not set
CONFIG_FILE_LOCKING=y
CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
CONFIG_NFS_V4=y
+# CONFIG_NFS_V4_1 is not set
CONFIG_ROOT_NFS=y
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_FRAME_WARN=1024
# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
# CONFIG_PAGE_POISONING is not set
CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
CONFIG_EARLY_SCIF_CONSOLE=y
CONFIG_EARLY_SCIF_CONSOLE_PORT=0xffeb0000
CONFIG_EARLY_PRINTK=y
-# CONFIG_DEBUG_BOOTMEM is not set
-# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_STACK_DEBUG is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_4KSTACKS is not set
# CONFIG_DUMP_CODE is not set
+# CONFIG_DWARF_UNWINDER is not set
# CONFIG_SH_NO_BSS_INIT is not set
#
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
CONFIG_CRYPTO_HMAC=y
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=y
# CONFIG_CRYPTO_MICHAEL_MIC is not set
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+CONFIG_HAVE_LMB=y
CONFIG_NLATTR=y
CONFIG_GENERIC_ATOMIC64=y
menu "DMA support"
-config SH_DMA_API
- bool
config SH_DMA
bool "SuperH on-chip DMA controller (DMAC) support"
depends on CPU_SH3 || CPU_SH4
- select SH_DMA_API
default n
config SH_DMA_IRQ_MULTI
CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785 || \
CPU_SUBTYPE_SH7760
+config SH_DMA_API
+ depends on SH_DMA
+ bool "SuperH DMA API support"
+ default n
+ help
+ SH_DMA_API always enabled DMA API of used SuperH.
+ If you want to use DMA ENGINE, you must not enable this.
+ Please enable DMA_ENGINE and SH_DMAE.
+
config NR_ONCHIP_DMA_CHANNELS
int
depends on SH_DMA
# Makefile for the SuperH DMA specific kernel interface routines under Linux.
#
-obj-$(CONFIG_SH_DMA_API) += dma-api.o dma-sysfs.o
-obj-$(CONFIG_SH_DMA) += dma-sh.o
+obj-$(CONFIG_SH_DMA_API) += dma-sh.o dma-api.o dma-sysfs.o
obj-$(CONFIG_PVR2_DMA) += dma-pvr2.o
obj-$(CONFIG_G2_DMA) += dma-g2.o
obj-$(CONFIG_SH_DMABRG) += dmabrg.o
#define CHCR 0x0C
#define DMAOR 0x40
+/*
+ * for dma engine
+ *
+ * SuperH DMA mode
+ */
+#define SHDMA_MIX_IRQ (1 << 1)
+#define SHDMA_DMAOR1 (1 << 2)
+#define SHDMA_DMAE1 (1 << 3)
+
+struct sh_dmae_pdata {
+ unsigned int mode;
+};
+
#endif /* __DMA_SH_H */
#include <linux/sh_timer.h>
#include <asm/clock.h>
#include <asm/mmzone.h>
+#include <asm/dma-sh.h>
#include <cpu/sh7722.h>
static struct resource rtc_resources[] = {
},
};
+static struct sh_dmae_pdata dma_platform_data = {
+ .mode = 0,
+};
+
+static struct platform_device dma_device = {
+ .name = "sh-dma-engine",
+ .id = -1,
+ .dev = {
+ .platform_data = &dma_platform_data,
+ },
+};
+
static struct platform_device *sh7722_devices[] __initdata = {
&cmt_device,
&tmu0_device,
&vpu_device,
&veu_device,
&jpu_device,
+ &dma_device,
};
static int __init sh7722_devices_setup(void)
#include <linux/io.h>
#include <linux/serial_sci.h>
#include <linux/sh_timer.h>
+#include <asm/dma-sh.h>
static struct sh_timer_config tmu0_platform_data = {
.name = "TMU0",
},
};
+static struct sh_dmae_pdata dma_platform_data = {
+ .mode = (SHDMA_MIX_IRQ | SHDMA_DMAOR1),
+};
+
+static struct platform_device dma_device = {
+ .name = "sh-dma-engine",
+ .id = -1,
+ .dev = {
+ .platform_data = &dma_platform_data,
+ },
+};
+
static struct platform_device *sh7780_devices[] __initdata = {
&tmu0_device,
&tmu1_device,
&tmu5_device,
&rtc_device,
&sci_device,
+ &dma_device,
};
static int __init sh7780_devices_setup(void)
#include <asm/unwinder.h>
#include <asm/sections.h>
#include <asm/unaligned.h>
-#include <asm/dwarf.h>
#include <asm/stacktrace.h>
/* Reserve enough memory for two stack frames */
u_int rm;
int ret, index;
+ /*
+ * XXX: We can't handle mixed 16/32-bit instructions yet
+ */
+ if (instruction_size(instruction) != 2)
+ return -EINVAL;
+
index = (instruction>>8)&15; /* 0x0F00 */
rm = regs->regs[index];
se_user += 1;
-#ifndef CONFIG_CPU_SH2A
set_fs(USER_DS);
- if (copy_from_user(&instruction, (u16 *)(regs->pc & ~1), 2)) {
+ if (copy_from_user(&instruction, (insn_size_t *)(regs->pc & ~1),
+ sizeof(instruction))) {
set_fs(oldfs);
goto uspace_segv;
}
"in \"%s\" pid=%d pc=0x%p ins=0x%04hx\n",
current->comm, current->pid, (void *)regs->pc,
instruction);
-#endif
if (se_usermode & 2)
goto fixup;
} else {
se_sys += 1;
- if (se_kernmode_warn)
- printk(KERN_NOTICE "Unaligned kernel access "
- "on behalf of \"%s\" pid=%d pc=0x%p ins=0x%04hx\n",
- current->comm, current->pid, (void *)regs->pc,
- instruction);
-
if (regs->pc & 1)
die("unaligned program counter", regs, error_code);
die("insn faulting in do_address_error", regs, 0);
}
+ if (se_kernmode_warn)
+ printk(KERN_NOTICE "Unaligned kernel access "
+ "on behalf of \"%s\" pid=%d pc=0x%p ins=0x%04hx\n",
+ current->comm, current->pid, (void *)regs->pc,
+ instruction);
+
handle_unaligned_access(instruction, regs,
&user_mem_access, 0);
set_fs(oldfs);
config NEED_PER_CPU_EMBED_FIRST_CHUNK
def_bool y if SPARC64
+config NEED_PER_CPU_PAGE_FIRST_CHUNK
+ def_bool y if SPARC64
+
config GENERIC_HARDIRQS_NO__DO_IRQ
bool
def_bool y if SPARC64
static inline u32 vio_dring_avail(struct vio_dring_state *dr,
unsigned int ring_size)
{
- MAYBE_BUILD_BUG_ON(!is_power_of_2(ring_size));
-
return (dr->pending -
((dr->prod - dr->cons) & (ring_size - 1)));
}
free_bootmem(__pa(ptr), size);
}
-static int pcpu_cpu_distance(unsigned int from, unsigned int to)
+static int __init pcpu_cpu_distance(unsigned int from, unsigned int to)
{
if (cpu_to_node(from) == cpu_to_node(to))
return LOCAL_DISTANCE;
return REMOTE_DISTANCE;
}
+static void __init pcpu_populate_pte(unsigned long addr)
+{
+ pgd_t *pgd = pgd_offset_k(addr);
+ pud_t *pud;
+ pmd_t *pmd;
+
+ pud = pud_offset(pgd, addr);
+ if (pud_none(*pud)) {
+ pmd_t *new;
+
+ new = __alloc_bootmem(PAGE_SIZE, PAGE_SIZE, PAGE_SIZE);
+ pud_populate(&init_mm, pud, new);
+ }
+
+ pmd = pmd_offset(pud, addr);
+ if (!pmd_present(*pmd)) {
+ pte_t *new;
+
+ new = __alloc_bootmem(PAGE_SIZE, PAGE_SIZE, PAGE_SIZE);
+ pmd_populate_kernel(&init_mm, pmd, new);
+ }
+}
+
void __init setup_per_cpu_areas(void)
{
unsigned long delta;
unsigned int cpu;
- int rc;
-
- rc = pcpu_embed_first_chunk(PERCPU_MODULE_RESERVE,
- PERCPU_DYNAMIC_RESERVE, 4 << 20,
- pcpu_cpu_distance, pcpu_alloc_bootmem,
- pcpu_free_bootmem);
- if (rc)
- panic("failed to initialize first chunk (%d)", rc);
+ int rc = -EINVAL;
+
+ if (pcpu_chosen_fc != PCPU_FC_PAGE) {
+ rc = pcpu_embed_first_chunk(PERCPU_MODULE_RESERVE,
+ PERCPU_DYNAMIC_RESERVE, 4 << 20,
+ pcpu_cpu_distance,
+ pcpu_alloc_bootmem,
+ pcpu_free_bootmem);
+ if (rc)
+ pr_warning("PERCPU: %s allocator failed (%d), "
+ "falling back to page size\n",
+ pcpu_fc_names[pcpu_chosen_fc], rc);
+ }
+ if (rc < 0)
+ rc = pcpu_page_first_chunk(PERCPU_MODULE_RESERVE,
+ pcpu_alloc_bootmem,
+ pcpu_free_bootmem,
+ pcpu_populate_pte);
+ if (rc < 0)
+ panic("cannot initialize percpu area (err=%d)", rc);
delta = (unsigned long)pcpu_base_addr - (unsigned long)__per_cpu_start;
for_each_possible_cpu(cpu)
. = ALIGN(4096);
.note : { *(.note.*) }
- __ex_table : {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
+ EXCEPTION_TABLE(0)
BUG_TABLE
}
.init.setup : {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
+ INIT_SETUP(0)
}
- . = ALIGN(32);
- .data.percpu : {
- __per_cpu_start = . ;
- *(.data.percpu)
- __per_cpu_end = . ;
- }
+ PERCPU(32)
.initcall.init : {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
+ INIT_CALLS
}
.con_initcall.init : {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
+ CON_INITCALL
}
.uml.initcall.init : {
. = ALIGN(4096);
.init.ramfs : {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
+ INIT_RAM_FS
}
_text = .;
_stext = .;
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
. = ALIGN(PAGE_SIZE);
.init_array : { *(.init_array) }
.fini_array : { *(.fini_array) }
.data : {
- . = ALIGN(KERNEL_STACK_SIZE); /* init_task */
- *(.data.init_task)
+ INIT_TASK_DATA(KERNEL_STACK_SIZE)
. = ALIGN(KERNEL_STACK_SIZE);
*(.data.init_irqstack)
DATA_DATA
_text = .;
_stext = .;
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
. = ALIGN(PAGE_SIZE);
.text :
init.data : { INIT_DATA }
.data :
{
- . = ALIGN(KERNEL_STACK_SIZE); /* init_task */
- *(.data.init_task)
+ INIT_TASK_DATA(KERNEL_STACK_SIZE)
. = ALIGN(KERNEL_STACK_SIZE);
*(.data.init_irqstack)
DATA_DATA
_edata = .;
PROVIDE (edata = .);
. = ALIGN(PAGE_SIZE);
- .sbss :
- {
- __bss_start = .;
- PROVIDE(_bss_start = .);
- *(.sbss)
- *(.scommon)
- }
- .bss :
- {
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
+ __bss_start = .;
+ PROVIDE(_bss_start = .);
+ SBSS(0)
+ BSS(0)
_end = .;
PROVIDE (end = .);
config HAVE_LATENCYTOP_SUPPORT
def_bool y
-config FAST_CMPXCHG_LOCAL
- bool
- default y
-
config MMU
def_bool y
of Flat Logical. You will need a new lynxer.elf file to flash your
firmware with - send email to <Martin.Bligh@us.ibm.com>.
+config X86_SUPPORTS_MEMORY_FAILURE
+ bool
+ # MCE code calls memory_failure():
+ depends on X86_MCE
+ # On 32-bit this adds too big of NODES_SHIFT and we run out of page flags:
+ depends on !X86_NUMAQ
+ # On 32-bit SPARSEMEM adds too big of SECTIONS_WIDTH:
+ depends on X86_64 || !SPARSEMEM
+ select ARCH_SUPPORTS_MEMORY_FAILURE
+ default y
+
config X86_VISWS
bool "SGI 320/540 (Visual Workstation)"
depends on X86_32 && PCI && X86_MPPARSE && PCI_GODIRECT
config X86_CMPXCHG64
def_bool y
- depends on X86_PAE || X86_64
+ depends on X86_PAE || X86_64 || MCORE2 || MPENTIUM4 || MPENTIUMM || MPENTIUMIII || MPENTIUMII || M686 || MATOM
# this should be set for all -march=.. options where the compiler
# generates cmov.
int
default "64" if X86_64
default "6" if X86_32 && X86_P6_NOP
+ default "5" if X86_32 && X86_CMPXCHG64
default "4" if X86_32 && (X86_XADD || X86_CMPXCHG || X86_BSWAP || X86_WP_WORKS_OK)
default "3"
*/
.text
+#include <linux/init.h>
#include <linux/linkage.h>
#include <asm/segment.h>
#include <asm/page_types.h>
#include <asm/boot.h>
#include <asm/asm-offsets.h>
- .section ".text.head","ax",@progbits
+ __HEAD
ENTRY(startup_32)
cld
/*
.code32
.text
+#include <linux/init.h>
#include <linux/linkage.h>
#include <asm/segment.h>
#include <asm/pgtable_types.h>
#include <asm/processor-flags.h>
#include <asm/asm-offsets.h>
- .section ".text.head"
+ __HEAD
.code32
ENTRY(startup_32)
cld
+#include <asm-generic/vmlinux.lds.h>
+
OUTPUT_FORMAT(CONFIG_OUTPUT_FORMAT, CONFIG_OUTPUT_FORMAT, CONFIG_OUTPUT_FORMAT)
#undef i386
* address 0.
*/
. = 0;
- .text.head : {
+ .head.text : {
_head = . ;
- *(.text.head)
+ HEAD_TEXT
_ehead = . ;
}
.rodata.compressed : {
#define __AUDIT_ARCH_LE 0x40000000
#ifndef CONFIG_AUDITSYSCALL
-#define sysexit_audit int_ret_from_sys_call
-#define sysretl_audit int_ret_from_sys_call
+#define sysexit_audit ia32_ret_from_sys_call
+#define sysretl_audit ia32_ret_from_sys_call
#endif
#define IA32_NR_syscalls ((ia32_syscall_end - ia32_sys_call_table)/8)
.endm
/* clobbers %eax */
- .macro CLEAR_RREGS _r9=rax
+ .macro CLEAR_RREGS offset=0, _r9=rax
xorl %eax,%eax
- movq %rax,R11(%rsp)
- movq %rax,R10(%rsp)
- movq %\_r9,R9(%rsp)
- movq %rax,R8(%rsp)
+ movq %rax,\offset+R11(%rsp)
+ movq %rax,\offset+R10(%rsp)
+ movq %\_r9,\offset+R9(%rsp)
+ movq %rax,\offset+R8(%rsp)
.endm
/*
movl RIP-R11(%rsp),%edx /* User %eip */
CFI_REGISTER rip,rdx
RESTORE_ARGS 1,24,1,1,1,1
+ xorq %r8,%r8
+ xorq %r9,%r9
+ xorq %r10,%r10
+ xorq %r11,%r11
popfq
CFI_ADJUST_CFA_OFFSET -8
/*CFI_RESTORE rflags*/
.macro auditsys_exit exit,ebpsave=RBP
testl $(_TIF_ALLWORK_MASK & ~_TIF_SYSCALL_AUDIT),TI_flags(%r10)
- jnz int_ret_from_sys_call
+ jnz ia32_ret_from_sys_call
TRACE_IRQS_ON
sti
movl %eax,%esi /* second arg, syscall return value */
cli
TRACE_IRQS_OFF
testl %edi,TI_flags(%r10)
- jnz int_with_check
- jmp \exit
+ jz \exit
+ CLEAR_RREGS -ARGOFFSET
+ jmp int_with_check
.endm
sysenter_auditsys:
CFI_REGISTER rip,rcx
movl EFLAGS-ARGOFFSET(%rsp),%r11d
/*CFI_REGISTER rflags,r11*/
+ xorq %r10,%r10
+ xorq %r9,%r9
+ xorq %r8,%r8
TRACE_IRQS_ON
movl RSP-ARGOFFSET(%rsp),%esp
CFI_RESTORE rsp
#endif
xchgl %r9d,%ebp
SAVE_REST
- CLEAR_RREGS r9
+ CLEAR_RREGS 0, r9
movq $-ENOSYS,RAX(%rsp) /* ptrace can change this for a bad syscall */
movq %rsp,%rdi /* &pt_regs -> arg1 */
call syscall_trace_enter
call *ia32_sys_call_table(,%rax,8) # xxx: rip relative
ia32_sysret:
movq %rax,RAX-ARGOFFSET(%rsp)
+ia32_ret_from_sys_call:
+ CLEAR_RREGS -ARGOFFSET
jmp int_ret_from_sys_call
ia32_tracesys:
ia32_badsys:
movq $0,ORIG_RAX-ARGOFFSET(%rsp)
- movq $-ENOSYS,RAX-ARGOFFSET(%rsp)
- jmp int_ret_from_sys_call
+ movq $-ENOSYS,%rax
+ jmp ia32_sysret
quiet_ni_syscall:
movq $-ENOSYS,%rax
"adcl $0, %0 ;\n"
: "=&r" (sum)
: "r" (saddr), "r" (daddr),
- "r" (htonl(len)), "r" (htonl(proto)), "0" (sum));
+ "r" (htonl(len)), "r" (htonl(proto)), "0" (sum)
+ : "memory");
return csum_fold(sum);
}
extern unsigned long long cmpxchg_486_u64(volatile void *, u64, u64);
-#define cmpxchg64(ptr, o, n) \
-({ \
- __typeof__(*(ptr)) __ret; \
- if (likely(boot_cpu_data.x86 > 4)) \
- __ret = (__typeof__(*(ptr)))__cmpxchg64((ptr), \
- (unsigned long long)(o), \
- (unsigned long long)(n)); \
- else \
- __ret = (__typeof__(*(ptr)))cmpxchg_486_u64((ptr), \
- (unsigned long long)(o), \
- (unsigned long long)(n)); \
- __ret; \
-})
+#define cmpxchg64(ptr, o, n) \
+({ \
+ __typeof__(*(ptr)) __ret; \
+ __typeof__(*(ptr)) __old = (o); \
+ __typeof__(*(ptr)) __new = (n); \
+ alternative_io("call cmpxchg8b_emu", \
+ "lock; cmpxchg8b (%%esi)" , \
+ X86_FEATURE_CX8, \
+ "=A" (__ret), \
+ "S" ((ptr)), "0" (__old), \
+ "b" ((unsigned int)__new), \
+ "c" ((unsigned int)(__new>>32)) \
+ : "memory"); \
+ __ret; })
+
+
+
#define cmpxchg64_local(ptr, o, n) \
({ \
__typeof__(*(ptr)) __ret; \
#define NMI_INVALID 3
struct ctl_table;
-struct file;
-extern int proc_nmi_enabled(struct ctl_table *, int , struct file *,
+extern int proc_nmi_enabled(struct ctl_table *, int ,
void __user *, size_t *, loff_t *);
extern int unknown_nmi_panic;
static inline const struct cpumask *
cpumask_of_pcibus(const struct pci_bus *bus)
{
- return cpumask_of_node(__pcibus_to_node(bus));
+ int node;
+
+ node = __pcibus_to_node(bus);
+ return (node == -1) ? cpu_online_mask :
+ cpumask_of_node(node);
}
#endif
typedef struct page *pgtable_t;
extern pteval_t __supported_pte_mask;
+extern void set_nx(void);
extern int nx_enabled;
#define pgprot_writecombine pgprot_writecombine
return 0;
}
-static inline int cpu_to_node(int cpu)
-{
- return 0;
-}
-
static inline int early_cpu_to_node(int cpu)
{
return 0;
}
-static inline const struct cpumask *cpumask_of_node(int node)
-{
- return cpu_online_mask;
-}
-
static inline void setup_node_to_cpumask_map(void) { }
#endif
* P4, Core and beyond CPUs
*/
if (c->x86_vendor == X86_VENDOR_INTEL &&
- (c->x86 > 0x6 || (c->x86 == 6 && c->x86_model >= 14)))
+ (c->x86 > 0xf || (c->x86 == 6 && c->x86_model >= 14)))
flags->bm_control = 0;
}
EXPORT_SYMBOL(acpi_processor_power_init_bm_check);
/*
* proc handler for /proc/sys/kernel/nmi
*/
-int proc_nmi_enabled(struct ctl_table *table, int write, struct file *file,
+int proc_nmi_enabled(struct ctl_table *table, int write,
void __user *buffer, size_t *length, loff_t *ppos)
{
int old_state;
nmi_watchdog_enabled = (atomic_read(&nmi_active) > 0) ? 1 : 0;
old_state = nmi_watchdog_enabled;
- proc_dointvec(table, write, file, buffer, length, ppos);
+ proc_dointvec(table, write, buffer, length, ppos);
if (!!old_state == !!nmi_watchdog_enabled)
return 0;
};
/* Inject mce on current CPU */
-static int raise_local(struct mce *m)
+static int raise_local(void)
{
+ struct mce *m = &__get_cpu_var(injectm);
int context = MCJ_CTX(m->inject_flags);
int ret = 0;
int cpu = m->extcpu;
}
cpu_relax();
}
- raise_local(m);
+ raise_local();
put_cpu();
put_online_cpus();
} else
#endif
- raise_local(m);
+ raise_local();
}
/* Error injection interface */
static void print_mce_tail(void)
{
printk(KERN_EMERG "This is not a software problem!\n"
-#if (!defined(CONFIG_EDAC) || !defined(CONFIG_CPU_SUP_AMD))
- "Run through mcelog --ascii to decode and contact your hardware vendor\n"
-#endif
- );
+ "Run through mcelog --ascii to decode and contact your hardware vendor\n");
}
#define PANIC_TIMEOUT 5 /* 5 seconds */
static u64 mce_rdmsrl(u32 msr)
{
u64 v;
+
if (__get_cpu_var(injectm).finished) {
int offset = msr_to_offset(msr);
+
if (offset < 0)
return 0;
return *(u64 *)((char *)&__get_cpu_var(injectm) + offset);
}
- rdmsrl(msr, v);
+
+ if (rdmsrl_safe(msr, &v)) {
+ WARN_ONCE(1, "mce: Unable to read msr %d!\n", msr);
+ /*
+ * Return zero in case the access faulted. This should
+ * not happen normally but can happen if the CPU does
+ * something weird, or if the code is buggy.
+ */
+ v = 0;
+ }
+
return v;
}
{
if (__get_cpu_var(injectm).finished) {
int offset = msr_to_offset(msr);
+
if (offset >= 0)
*(u64 *)((char *)&__get_cpu_var(injectm) + offset) = v;
return;
m->ip = mce_rdmsrl(rip_msr);
}
-#ifdef CONFIG_X86_LOCAL_APIC
+#ifdef CONFIG_X86_LOCAL_APIC
/*
* Called after interrupts have been reenabled again
* when a MCE happened during an interrupts off region
return -ENOMEM;
for (i = 0; i < banks; i++) {
struct mce_bank *b = &mce_banks[i];
+
b->ctl = -1ULL;
b->init = 1;
}
banks = b;
if (!mce_banks) {
int err = mce_banks_init();
+
if (err)
return err;
}
for (i = 0; i < banks; i++) {
struct mce_bank *b = &mce_banks[i];
+
if (!b->init)
continue;
wrmsrl(MSR_IA32_MCx_CTL(i), b->ctl);
for (i = 0; i < banks; i++) {
struct mce_bank *b = &mce_banks[i];
+
if (b->init)
wrmsrl(MSR_IA32_MCx_CTL(i), 0);
}
cmci_clear();
for (i = 0; i < banks; i++) {
struct mce_bank *b = &mce_banks[i];
+
if (b->init)
wrmsrl(MSR_IA32_MCx_CTL(i), 0);
}
cmci_reenable();
for (i = 0; i < banks; i++) {
struct mce_bank *b = &mce_banks[i];
+
if (b->init)
wrmsrl(MSR_IA32_MCx_CTL(i), b->ctl);
}
/* How long to wait between reporting thermal events */
#define CHECK_INTERVAL (300 * HZ)
-static DEFINE_PER_CPU(__u64, next_check) = INITIAL_JIFFIES;
-static DEFINE_PER_CPU(unsigned long, thermal_throttle_count);
-static DEFINE_PER_CPU(bool, thermal_throttle_active);
+/*
+ * Current thermal throttling state:
+ */
+struct thermal_state {
+ bool is_throttled;
+
+ u64 next_check;
+ unsigned long throttle_count;
+ unsigned long last_throttle_count;
+};
+
+static DEFINE_PER_CPU(struct thermal_state, thermal_state);
-static atomic_t therm_throt_en = ATOMIC_INIT(0);
+static atomic_t therm_throt_en = ATOMIC_INIT(0);
#ifdef CONFIG_SYSFS
#define define_therm_throt_sysdev_one_ro(_name) \
static SYSDEV_ATTR(_name, 0444, therm_throt_sysdev_show_##_name, NULL)
#define define_therm_throt_sysdev_show_func(name) \
-static ssize_t therm_throt_sysdev_show_##name(struct sys_device *dev, \
- struct sysdev_attribute *attr, \
- char *buf) \
+ \
+static ssize_t therm_throt_sysdev_show_##name( \
+ struct sys_device *dev, \
+ struct sysdev_attribute *attr, \
+ char *buf) \
{ \
unsigned int cpu = dev->id; \
ssize_t ret; \
preempt_disable(); /* CPU hotplug */ \
if (cpu_online(cpu)) \
ret = sprintf(buf, "%lu\n", \
- per_cpu(thermal_throttle_##name, cpu)); \
+ per_cpu(thermal_state, cpu).name); \
else \
ret = 0; \
preempt_enable(); \
return ret; \
}
-define_therm_throt_sysdev_show_func(count);
-define_therm_throt_sysdev_one_ro(count);
+define_therm_throt_sysdev_show_func(throttle_count);
+define_therm_throt_sysdev_one_ro(throttle_count);
static struct attribute *thermal_throttle_attrs[] = {
- &attr_count.attr,
+ &attr_throttle_count.attr,
NULL
};
* 1 : Event should be logged further, and a message has been
* printed to the syslog.
*/
-static int therm_throt_process(int curr)
+static int therm_throt_process(bool is_throttled)
{
- unsigned int cpu = smp_processor_id();
- __u64 tmp_jiffs = get_jiffies_64();
- bool was_throttled = __get_cpu_var(thermal_throttle_active);
- bool is_throttled = __get_cpu_var(thermal_throttle_active) = curr;
+ struct thermal_state *state;
+ unsigned int this_cpu;
+ bool was_throttled;
+ u64 now;
+
+ this_cpu = smp_processor_id();
+ now = get_jiffies_64();
+ state = &per_cpu(thermal_state, this_cpu);
+
+ was_throttled = state->is_throttled;
+ state->is_throttled = is_throttled;
if (is_throttled)
- __get_cpu_var(thermal_throttle_count)++;
+ state->throttle_count++;
- if (!(was_throttled ^ is_throttled) &&
- time_before64(tmp_jiffs, __get_cpu_var(next_check)))
+ if (time_before64(now, state->next_check) &&
+ state->throttle_count != state->last_throttle_count)
return 0;
- __get_cpu_var(next_check) = tmp_jiffs + CHECK_INTERVAL;
+ state->next_check = now + CHECK_INTERVAL;
+ state->last_throttle_count = state->throttle_count;
/* if we just entered the thermal event */
if (is_throttled) {
- printk(KERN_CRIT "CPU%d: Temperature above threshold, "
- "cpu clock throttled (total events = %lu)\n",
- cpu, __get_cpu_var(thermal_throttle_count));
+ printk(KERN_CRIT "CPU%d: Temperature above threshold, cpu clock throttled (total events = %lu)\n", this_cpu, state->throttle_count);
add_taint(TAINT_MACHINE_CHECK);
return 1;
}
if (was_throttled) {
- printk(KERN_INFO "CPU%d: Temperature/speed normal\n", cpu);
+ printk(KERN_INFO "CPU%d: Temperature/speed normal\n", this_cpu);
return 1;
}
__u64 msr_val;
rdmsrl(MSR_IA32_THERM_STATUS, msr_val);
- if (therm_throt_process(msr_val & THERM_STATUS_PROCHOT))
+ if (therm_throt_process((msr_val & THERM_STATUS_PROCHOT) != 0))
mce_log_therm_throt_event(msr_val);
}
void set_perf_event_pending(void)
{
#ifdef CONFIG_X86_LOCAL_APIC
+ if (!x86_pmu.apic || !x86_pmu_initialized())
+ return;
+
apic->send_IPI_self(LOCAL_PENDING_VECTOR);
#endif
}
static inline void early_console_register(struct console *con, int keep_early)
{
+ if (early_console->index != -1) {
+ printk(KERN_CRIT "ERROR: earlyprintk= %s already used\n",
+ con->name);
+ return;
+ }
early_console = con;
if (keep_early)
early_console->flags &= ~CON_BOOT;
while (*buf != '\0') {
if (!strncmp(buf, "serial", 6)) {
- early_serial_init(buf + 6);
+ buf += 6;
+ early_serial_init(buf);
early_console_register(&early_serial_console, keep);
+ if (!strncmp(buf, ",ttyS", 5))
+ buf += 5;
}
if (!strncmp(buf, "ttyS", 4)) {
early_serial_init(buf + 4);
* any particular GDT layout, because we load our own as soon as we
* can.
*/
-.section .text.head,"ax",@progbits
+__HEAD
ENTRY(startup_32)
/* test KEEP_SEGMENTS flag to see if the bootloader is asking
us to not reload segments */
L3_START_KERNEL = pud_index(__START_KERNEL_map)
.text
- .section .text.head
+ __HEAD
.code64
.globl startup_64
startup_64:
EXPORT_SYMBOL(mcount);
#endif
+/*
+ * Note, this is a prototype to get at the symbol for
+ * the export, but dont use it from C code, it is used
+ * by assembly code and is not using C calling convention!
+ */
+#ifndef CONFIG_X86_CMPXCHG64
+extern void cmpxchg8b_emu(void);
+EXPORT_SYMBOL(cmpxchg8b_emu);
+#endif
+
/* Networking helper routines. */
EXPORT_SYMBOL(csum_partial_copy_generic);
/*
* The IDT has to be page-aligned to simplify the Pentium
- * F0 0F bug workaround.. We have a special link segment
- * for this.
+ * F0 0F bug workaround.
*/
-gate_desc idt_table[NR_VECTORS]
- __attribute__((__section__(".data.idt"))) = { { { { 0, 0 } } }, };
+gate_desc idt_table[NR_VECTORS] __page_aligned_data = { { { { 0, 0 } } }, };
#endif
DECLARE_BITMAP(used_vectors, NR_VECTORS);
return;
if (boot_cpu_has(X86_FEATURE_TSC_RELIABLE)) {
- pr_info("Skipping synchronization checks as TSC is reliable.\n");
+ printk_once(KERN_INFO "Skipping synchronization checks as TSC is reliable.\n");
return;
}
#endif
/* Text and read-only data */
-
- /* bootstrapping code */
- .text.head : AT(ADDR(.text.head) - LOAD_OFFSET) {
- _text = .;
- *(.text.head)
- } :text = 0x9090
-
- /* The rest of the text */
.text : AT(ADDR(.text) - LOAD_OFFSET) {
+ _text = .;
+ /* bootstrapping code */
+ HEAD_TEXT
#ifdef CONFIG_X86_32
- /* not really needed, already page aligned */
. = ALIGN(PAGE_SIZE);
*(.text.page_aligned)
#endif
NOTES :text :note
- /* Exception table */
- . = ALIGN(16);
- __ex_table : AT(ADDR(__ex_table) - LOAD_OFFSET) {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- } :text = 0x9090
+ EXCEPTION_TABLE(16) :text = 0x9090
RO_DATA(PAGE_SIZE)
#endif
PAGE_ALIGNED_DATA(PAGE_SIZE)
- *(.data.idt)
CACHELINE_ALIGNED_DATA(CONFIG_X86_L1_CACHE_BYTES)
#ifdef CONFIG_X86_64
#define VSYSCALL_ADDR (-10*1024*1024)
-#define VSYSCALL_PHYS_ADDR ((LOADADDR(.data) + SIZEOF(.data) + \
- PAGE_SIZE - 1) & ~(PAGE_SIZE - 1))
-#define VSYSCALL_VIRT_ADDR ((ADDR(.data) + SIZEOF(.data) + \
- PAGE_SIZE - 1) & ~(PAGE_SIZE - 1))
-#define VLOAD_OFFSET (VSYSCALL_ADDR - VSYSCALL_PHYS_ADDR)
+#define VLOAD_OFFSET (VSYSCALL_ADDR - __vsyscall_0 + LOAD_OFFSET)
#define VLOAD(x) (ADDR(x) - VLOAD_OFFSET)
-#define VVIRT_OFFSET (VSYSCALL_ADDR - VSYSCALL_VIRT_ADDR)
+#define VVIRT_OFFSET (VSYSCALL_ADDR - __vsyscall_0)
#define VVIRT(x) (ADDR(x) - VVIRT_OFFSET)
+ . = ALIGN(4096);
+ __vsyscall_0 = .;
+
. = VSYSCALL_ADDR;
- .vsyscall_0 : AT(VSYSCALL_PHYS_ADDR) {
+ .vsyscall_0 : AT(VLOAD(.vsyscall_0)) {
*(.vsyscall_0)
} :user
- __vsyscall_0 = VSYSCALL_VIRT_ADDR;
-
. = ALIGN(CONFIG_X86_L1_CACHE_BYTES);
.vsyscall_fn : AT(VLOAD(.vsyscall_fn)) {
*(.vsyscall_fn)
*(.vsyscall_3)
}
- . = VSYSCALL_VIRT_ADDR + PAGE_SIZE;
+ . = __vsyscall_0 + PAGE_SIZE;
#undef VSYSCALL_ADDR
-#undef VSYSCALL_PHYS_ADDR
-#undef VSYSCALL_VIRT_ADDR
#undef VLOAD_OFFSET
#undef VLOAD
#undef VVIRT_OFFSET
PERCPU_VADDR(0, :percpu)
#endif
- .init.text : AT(ADDR(.init.text) - LOAD_OFFSET) {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
#ifdef CONFIG_X86_64
:init
#endif
- .init.data : AT(ADDR(.init.data) - LOAD_OFFSET) {
- INIT_DATA
- }
-
- . = ALIGN(16);
- .init.setup : AT(ADDR(.init.setup) - LOAD_OFFSET) {
- __setup_start = .;
- *(.init.setup)
- __setup_end = .;
- }
- .initcall.init : AT(ADDR(.initcall.init) - LOAD_OFFSET) {
- __initcall_start = .;
- INITCALLS
- __initcall_end = .;
- }
-
- .con_initcall.init : AT(ADDR(.con_initcall.init) - LOAD_OFFSET) {
- __con_initcall_start = .;
- *(.con_initcall.init)
- __con_initcall_end = .;
- }
+ INIT_DATA_SECTION(16)
.x86_cpu_dev.init : AT(ADDR(.x86_cpu_dev.init) - LOAD_OFFSET) {
__x86_cpu_dev_start = .;
__x86_cpu_dev_end = .;
}
- SECURITY_INIT
-
. = ALIGN(8);
.parainstructions : AT(ADDR(.parainstructions) - LOAD_OFFSET) {
__parainstructions = .;
EXIT_DATA
}
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(PAGE_SIZE);
- .init.ramfs : AT(ADDR(.init.ramfs) - LOAD_OFFSET) {
- __initramfs_start = .;
- *(.init.ramfs)
- __initramfs_end = .;
- }
-#endif
-
#if !defined(CONFIG_X86_64) || !defined(CONFIG_SMP)
PERCPU(PAGE_SIZE)
#endif
}
#ifdef CONFIG_SYSCTL
-
-static int
-vsyscall_sysctl_change(ctl_table *ctl, int write, struct file * filp,
- void __user *buffer, size_t *lenp, loff_t *ppos)
-{
- return proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
-}
-
static ctl_table kernel_table2[] = {
{ .procname = "vsyscall64",
.data = &vsyscall_gtod_data.sysctl_enabled, .maxlen = sizeof(int),
.mode = 0644,
- .proc_handler = vsyscall_sysctl_change },
+ .proc_handler = proc_dointvec },
{}
};
lib-y += checksum_32.o
lib-y += strstr_32.o
lib-y += semaphore_32.o string_32.o
-
+ifneq ($(CONFIG_X86_CMPXCHG64),y)
+ lib-y += cmpxchg8b_emu.o
+endif
lib-$(CONFIG_X86_USE_3DNOW) += mmx_32.o
else
obj-y += io_64.o iomap_copy_64.o
--- /dev/null
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; version 2
+ * of the License.
+ *
+ */
+
+#include <linux/linkage.h>
+#include <asm/alternative-asm.h>
+#include <asm/frame.h>
+#include <asm/dwarf2.h>
+
+
+.text
+
+/*
+ * Inputs:
+ * %esi : memory location to compare
+ * %eax : low 32 bits of old value
+ * %edx : high 32 bits of old value
+ * %ebx : low 32 bits of new value
+ * %ecx : high 32 bits of new value
+ */
+ENTRY(cmpxchg8b_emu)
+CFI_STARTPROC
+
+#
+# Emulate 'cmpxchg8b (%esi)' on UP except we don't
+# set the whole ZF thing (caller will just compare
+# eax:edx with the expected value)
+#
+cmpxchg8b_emu:
+ pushfl
+ cli
+
+ cmpl (%esi), %eax
+ jne not_same
+ cmpl 4(%esi), %edx
+ jne half_same
+
+ movl %ebx, (%esi)
+ movl %ecx, 4(%esi)
+
+ popfl
+ ret
+
+ not_same:
+ movl (%esi), %eax
+ half_same:
+ movl 4(%esi), %edx
+
+ popfl
+ ret
+
+CFI_ENDPROC
+ENDPROC(cmpxchg8b_emu)
obj-y := init.o init_$(BITS).o fault.o ioremap.o extable.o pageattr.o mmap.o \
- pat.o pgtable.o physaddr.o gup.o
+ pat.o pgtable.o physaddr.o gup.o setup_nx.o
# Make sure __phys_addr has no stackprotector
nostackp := $(call cc-option, -fno-stack-protector)
CFLAGS_physaddr.o := $(nostackp)
+CFLAGS_setup_nx.o := $(nostackp)
obj-$(CONFIG_SMP) += tlb.o
info.si_errno = 0;
info.si_code = si_code;
info.si_addr = (void __user *)address;
+ info.si_addr_lsb = si_code == BUS_MCEERR_AR ? PAGE_SHIFT : 0;
force_sig_info(si_signo, &info, tsk);
}
}
static void
-do_sigbus(struct pt_regs *regs, unsigned long error_code, unsigned long address)
+do_sigbus(struct pt_regs *regs, unsigned long error_code, unsigned long address,
+ unsigned int fault)
{
struct task_struct *tsk = current;
struct mm_struct *mm = tsk->mm;
+ int code = BUS_ADRERR;
up_read(&mm->mmap_sem);
tsk->thread.error_code = error_code;
tsk->thread.trap_no = 14;
- force_sig_info_fault(SIGBUS, BUS_ADRERR, address, tsk);
+#ifdef CONFIG_MEMORY_FAILURE
+ if (fault & VM_FAULT_HWPOISON) {
+ printk(KERN_ERR
+ "MCE: Killing %s:%d due to hardware memory corruption fault at %lx\n",
+ tsk->comm, tsk->pid, address);
+ code = BUS_MCEERR_AR;
+ }
+#endif
+ force_sig_info_fault(SIGBUS, code, address, tsk);
}
static noinline void
if (fault & VM_FAULT_OOM) {
out_of_memory(regs, error_code, address);
} else {
- if (fault & VM_FAULT_SIGBUS)
- do_sigbus(regs, error_code, address);
+ if (fault & (VM_FAULT_SIGBUS|VM_FAULT_HWPOISON))
+ do_sigbus(regs, error_code, address, fault);
else
BUG();
}
#endif
;
-int nx_enabled;
-
-#if defined(CONFIG_X86_64) || defined(CONFIG_X86_PAE)
-static int disable_nx __cpuinitdata;
-
-/*
- * noexec = on|off
- *
- * Control non-executable mappings for processes.
- *
- * on Enable
- * off Disable
- */
-static int __init noexec_setup(char *str)
-{
- if (!str)
- return -EINVAL;
- if (!strncmp(str, "on", 2)) {
- __supported_pte_mask |= _PAGE_NX;
- disable_nx = 0;
- } else if (!strncmp(str, "off", 3)) {
- disable_nx = 1;
- __supported_pte_mask &= ~_PAGE_NX;
- }
- return 0;
-}
-early_param("noexec", noexec_setup);
-#endif
-
-#ifdef CONFIG_X86_PAE
-static void __init set_nx(void)
-{
- unsigned int v[4], l, h;
-
- if (cpu_has_pae && (cpuid_eax(0x80000000) > 0x80000001)) {
- cpuid(0x80000001, &v[0], &v[1], &v[2], &v[3]);
-
- if ((v[3] & (1 << 20)) && !disable_nx) {
- rdmsr(MSR_EFER, l, h);
- l |= EFER_NX;
- wrmsr(MSR_EFER, l, h);
- nx_enabled = 1;
- __supported_pte_mask |= _PAGE_NX;
- }
- }
-}
-#else
-static inline void set_nx(void)
-{
-}
-#endif
-
-#ifdef CONFIG_X86_64
-void __cpuinit check_efer(void)
-{
- unsigned long efer;
-
- rdmsrl(MSR_EFER, efer);
- if (!(efer & EFER_NX) || disable_nx)
- __supported_pte_mask &= ~_PAGE_NX;
-}
-#endif
-
static void __init find_early_table_space(unsigned long end, int use_pse,
int use_gbpages)
{
mb();
}
+EXPORT_SYMBOL_GPL(clflush_cache_range);
static void __cpa_flush_all(void *arg)
{
void pat_init(void)
{
u64 pat;
+ bool boot_cpu = !boot_pat_state;
if (!pat_enabled)
return;
rdmsrl(MSR_IA32_CR_PAT, boot_pat_state);
wrmsrl(MSR_IA32_CR_PAT, pat);
- printk(KERN_INFO "x86 PAT enabled: cpu %d, old 0x%Lx, new 0x%Lx\n",
- smp_processor_id(), boot_pat_state, pat);
+
+ if (boot_cpu)
+ printk(KERN_INFO "x86 PAT enabled: cpu %d, old 0x%Lx, new 0x%Lx\n",
+ smp_processor_id(), boot_pat_state, pat);
}
#undef PAT
--- /dev/null
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+
+#include <asm/pgtable.h>
+
+int nx_enabled;
+
+#if defined(CONFIG_X86_64) || defined(CONFIG_X86_PAE)
+static int disable_nx __cpuinitdata;
+
+/*
+ * noexec = on|off
+ *
+ * Control non-executable mappings for processes.
+ *
+ * on Enable
+ * off Disable
+ */
+static int __init noexec_setup(char *str)
+{
+ if (!str)
+ return -EINVAL;
+ if (!strncmp(str, "on", 2)) {
+ __supported_pte_mask |= _PAGE_NX;
+ disable_nx = 0;
+ } else if (!strncmp(str, "off", 3)) {
+ disable_nx = 1;
+ __supported_pte_mask &= ~_PAGE_NX;
+ }
+ return 0;
+}
+early_param("noexec", noexec_setup);
+#endif
+
+#ifdef CONFIG_X86_PAE
+void __init set_nx(void)
+{
+ unsigned int v[4], l, h;
+
+ if (cpu_has_pae && (cpuid_eax(0x80000000) > 0x80000001)) {
+ cpuid(0x80000001, &v[0], &v[1], &v[2], &v[3]);
+
+ if ((v[3] & (1 << 20)) && !disable_nx) {
+ rdmsr(MSR_EFER, l, h);
+ l |= EFER_NX;
+ wrmsr(MSR_EFER, l, h);
+ nx_enabled = 1;
+ __supported_pte_mask |= _PAGE_NX;
+ }
+ }
+}
+#else
+void set_nx(void)
+{
+}
+#endif
+
+#ifdef CONFIG_X86_64
+void __cpuinit check_efer(void)
+{
+ unsigned long efer;
+
+ rdmsrl(MSR_EFER, efer);
+ if (!(efer & EFER_NX) || disable_nx)
+ __supported_pte_mask &= ~_PAGE_NX;
+}
+#endif
+
#else /* CONFIG_X86_32 */
-static unsigned char mp_bus_to_node[BUS_NR] = {
+static int mp_bus_to_node[BUS_NR] = {
[0 ... BUS_NR - 1] = -1
};
pci_write_config_byte(dev, PCI_LATENCY_TIMER, lat);
}
-static struct vm_operations_struct pci_mmap_ops = {
+static const struct vm_operations_struct pci_mmap_ops = {
.access = generic_access_phys,
};
return 0;
}
-static struct file_operations u32_array_fops = {
+static const struct file_operations u32_array_fops = {
.owner = THIS_MODULE,
.open = u32_array_open,
.release= xen_array_release,
__supported_pte_mask |= _PAGE_IOMAP;
+#ifdef CONFIG_X86_64
+ /* Work out if we support NX */
+ check_efer();
+#endif
+
xen_setup_features();
/* Get mfn list */
pgd = (pgd_t *)xen_start_info->pt_base;
-#ifdef CONFIG_X86_64
- /* Work out if we support NX */
- check_efer();
-#endif
-
/* Don't do the full vcpu_info placement stuff until we have a
possible map and a non-dummy shared_info. */
per_cpu(xen_vcpu, 0) = &HYPERVISOR_shared_info->vcpu_info[0];
*/
#include <asm-generic/vmlinux.lds.h>
+#include <asm/page.h>
+#include <asm/thread_info.h>
#include <variant/core.h>
#include <platform/hardware.h>
.fixup : { *(.fixup) }
- . = ALIGN(16);
-
- __ex_table : {
- __start___ex_table = .;
- *(__ex_table)
- __stop___ex_table = .;
- }
-
+ EXCEPTION_TABLE(16)
/* Data section */
- . = ALIGN(XCHAL_ICACHE_LINESIZE);
_fdata = .;
- .data :
- {
- DATA_DATA
- CONSTRUCTORS
- . = ALIGN(XCHAL_ICACHE_LINESIZE);
- *(.data.cacheline_aligned)
- }
-
+ RW_DATA_SECTION(XCHAL_ICACHE_LINESIZE, PAGE_SIZE, THREAD_SIZE)
_edata = .;
- /* The initial task */
- . = ALIGN(8192);
- .data.init_task : { *(.data.init_task) }
-
/* Initialization code and data: */
- . = ALIGN(1 << 12);
+ . = ALIGN(PAGE_SIZE);
__init_begin = .;
- .init.text : {
- _sinittext = .;
- INIT_TEXT
- _einittext = .;
- }
+ INIT_TEXT_SECTION(PAGE_SIZE)
.init.data :
{
.DebugInterruptVector.text);
__boot_reloc_table_end = ABSOLUTE(.) ;
- }
- . = ALIGN(XCHAL_ICACHE_LINESIZE);
-
- __setup_start = .;
- .init.setup : { *(.init.setup) }
- __setup_end = .;
-
- __initcall_start = .;
- .initcall.init : {
- INITCALLS
+ INIT_SETUP(XCHAL_ICACHE_LINESIZE)
+ INIT_CALLS
+ CON_INITCALL
+ SECURITY_INITCALL
+ INIT_RAM_FS
}
- __initcall_end = .;
-
- __con_initcall_start = .;
- .con_initcall.init : { *(.con_initcall.init) }
- __con_initcall_end = .;
-
- SECURITY_INIT
-
-
-#ifdef CONFIG_BLK_DEV_INITRD
- . = ALIGN(4096);
- __initramfs_start =.;
- .init.ramfs : { *(.init.ramfs) }
- __initramfs_end = .;
-#endif
-
- PERCPU(4096)
+ PERCPU(PAGE_SIZE)
/* We need this dummy segment here */
.DoubleExceptionVector.literal)
. = (LOADADDR( .DoubleExceptionVector.text ) + SIZEOF( .DoubleExceptionVector.text ) + 3) & ~ 3;
- . = ALIGN(1 << 12);
+ . = ALIGN(PAGE_SIZE);
__init_end = .;
- . = ALIGN(8192);
-
- /* BSS section */
- _bss_start = .;
- .bss : { *(.bss.page_aligned) *(.bss) }
- _bss_end = .;
+ BSS_SECTION(0, 8192, 0)
_end = .;
if (bio->bi_private)
complete(bio->bi_private);
+ __free_page(bio_page(bio));
bio_put(bio);
}
struct request_queue *q = bdev_get_queue(bdev);
int type = flags & DISCARD_FL_BARRIER ?
DISCARD_BARRIER : DISCARD_NOBARRIER;
+ struct bio *bio;
+ struct page *page;
int ret = 0;
if (!q)
return -ENXIO;
- if (!q->prepare_discard_fn)
+ if (!blk_queue_discard(q))
return -EOPNOTSUPP;
while (nr_sects && !ret) {
- struct bio *bio = bio_alloc(gfp_mask, 0);
- if (!bio)
- return -ENOMEM;
+ unsigned int sector_size = q->limits.logical_block_size;
+ unsigned int max_discard_sectors =
+ min(q->limits.max_discard_sectors, UINT_MAX >> 9);
+ bio = bio_alloc(gfp_mask, 1);
+ if (!bio)
+ goto out;
+ bio->bi_sector = sector;
bio->bi_end_io = blkdev_discard_end_io;
bio->bi_bdev = bdev;
if (flags & DISCARD_FL_WAIT)
bio->bi_private = &wait;
- bio->bi_sector = sector;
+ /*
+ * Add a zeroed one-sector payload as that's what
+ * our current implementations need. If we'll ever need
+ * more the interface will need revisiting.
+ */
+ page = alloc_page(GFP_KERNEL | __GFP_ZERO);
+ if (!page)
+ goto out_free_bio;
+ if (bio_add_pc_page(q, bio, page, sector_size, 0) < sector_size)
+ goto out_free_page;
- if (nr_sects > queue_max_hw_sectors(q)) {
- bio->bi_size = queue_max_hw_sectors(q) << 9;
- nr_sects -= queue_max_hw_sectors(q);
- sector += queue_max_hw_sectors(q);
+ /*
+ * And override the bio size - the way discard works we
+ * touch many more blocks on disk than the actual payload
+ * length.
+ */
+ if (nr_sects > max_discard_sectors) {
+ bio->bi_size = max_discard_sectors << 9;
+ nr_sects -= max_discard_sectors;
+ sector += max_discard_sectors;
} else {
bio->bi_size = nr_sects << 9;
nr_sects = 0;
bio_put(bio);
}
return ret;
+out_free_page:
+ __free_page(page);
+out_free_bio:
+ bio_put(bio);
+out:
+ return -ENOMEM;
}
EXPORT_SYMBOL(blkdev_issue_discard);
#include "blk.h"
EXPORT_TRACEPOINT_SYMBOL_GPL(block_remap);
+EXPORT_TRACEPOINT_SYMBOL_GPL(block_rq_remap);
EXPORT_TRACEPOINT_SYMBOL_GPL(block_bio_complete);
static int __make_request(struct request_queue *q, struct bio *bio);
part_stat_inc(cpu, part, merges[rw]);
else {
part_round_stats(cpu, part);
- part_inc_in_flight(part, rw);
+ part_inc_in_flight(part);
}
part_stat_unlock();
if (part->in_flight) {
__part_stat_add(cpu, part, time_in_queue,
- part_in_flight(part) * (now - part->stamp));
+ part->in_flight * (now - part->stamp));
__part_stat_add(cpu, part, io_ticks, (now - part->stamp));
}
part->stamp = now;
req->cmd_flags |= REQ_DISCARD;
if (bio_rw_flagged(bio, BIO_RW_BARRIER))
req->cmd_flags |= REQ_SOFTBARRIER;
- req->q->prepare_discard_fn(req->q, req);
} else if (unlikely(bio_rw_flagged(bio, BIO_RW_BARRIER)))
req->cmd_flags |= REQ_HARDBARRIER;
goto end_io;
}
- if (unlikely(nr_sectors > queue_max_hw_sectors(q))) {
+ if (unlikely(!bio_rw_flagged(bio, BIO_RW_DISCARD) &&
+ nr_sectors > queue_max_hw_sectors(q))) {
printk(KERN_ERR "bio too big device %s (%u > %u)\n",
bdevname(bio->bi_bdev, b),
bio_sectors(bio),
goto end_io;
if (bio_rw_flagged(bio, BIO_RW_DISCARD) &&
- !q->prepare_discard_fn) {
+ !blk_queue_discard(q)) {
err = -EOPNOTSUPP;
goto end_io;
}
part_stat_inc(cpu, part, ios[rw]);
part_stat_add(cpu, part, ticks[rw], duration);
part_round_stats(cpu, part);
- part_dec_in_flight(part, rw);
+ part_dec_in_flight(part);
part_stat_unlock();
}
}
EXPORT_SYMBOL(kblockd_schedule_work);
+int kblockd_schedule_delayed_work(struct request_queue *q,
+ struct delayed_work *work,
+ unsigned long delay)
+{
+ return queue_delayed_work(kblockd_workqueue, work, delay);
+}
+EXPORT_SYMBOL(kblockd_schedule_delayed_work);
+
int __init blk_dev_init(void)
{
BUILD_BUG_ON(__REQ_NR_BITS > 8 *
part = disk_map_sector_rcu(req->rq_disk, blk_rq_pos(req));
part_round_stats(cpu, part);
- part_dec_in_flight(part, rq_data_dir(req));
+ part_dec_in_flight(part);
part_stat_unlock();
}
}
EXPORT_SYMBOL(blk_queue_prep_rq);
-/**
- * blk_queue_set_discard - set a discard_sectors function for queue
- * @q: queue
- * @dfn: prepare_discard function
- *
- * It's possible for a queue to register a discard callback which is used
- * to transform a discard request into the appropriate type for the
- * hardware. If none is registered, then discard requests are failed
- * with %EOPNOTSUPP.
- *
- */
-void blk_queue_set_discard(struct request_queue *q, prepare_discard_fn *dfn)
-{
- q->prepare_discard_fn = dfn;
-}
-EXPORT_SYMBOL(blk_queue_set_discard);
-
/**
* blk_queue_merge_bvec - set a merge_bvec function for queue
* @q: queue
lim->max_hw_segments = MAX_HW_SEGMENTS;
lim->seg_boundary_mask = BLK_SEG_BOUNDARY_MASK;
lim->max_segment_size = MAX_SEGMENT_SIZE;
- lim->max_sectors = lim->max_hw_sectors = SAFE_MAX_SECTORS;
+ lim->max_sectors = BLK_DEF_MAX_SECTORS;
+ lim->max_hw_sectors = INT_MAX;
+ lim->max_discard_sectors = SAFE_MAX_SECTORS;
lim->logical_block_size = lim->physical_block_size = lim->io_min = 512;
lim->bounce_pfn = (unsigned long)(BLK_BOUNCE_ANY >> PAGE_SHIFT);
lim->alignment_offset = 0;
q->unplug_timer.data = (unsigned long)q;
blk_set_default_limits(&q->limits);
+ blk_queue_max_sectors(q, SAFE_MAX_SECTORS);
/*
* If the caller didn't supply a lock, fall back to our embedded
}
EXPORT_SYMBOL(blk_queue_max_hw_sectors);
+/**
+ * blk_queue_max_discard_sectors - set max sectors for a single discard
+ * @q: the request queue for the device
+ * @max_discard: maximum number of sectors to discard
+ **/
+void blk_queue_max_discard_sectors(struct request_queue *q,
+ unsigned int max_discard_sectors)
+{
+ q->limits.max_discard_sectors = max_discard_sectors;
+}
+EXPORT_SYMBOL(blk_queue_max_discard_sectors);
+
/**
* blk_queue_max_phys_segments - set max phys segments for a request for this queue
* @q: the request queue for the device
if (ret) {
kobject_uevent(&q->kobj, KOBJ_REMOVE);
kobject_del(&q->kobj);
+ blk_trace_remove_sysfs(disk_to_dev(disk));
return ret;
}
if (WARN_ON(!q))
return;
- if (q->request_fn) {
+ if (q->request_fn)
elv_unregister_queue(q);
- kobject_uevent(&q->kobj, KOBJ_REMOVE);
- kobject_del(&q->kobj);
- kobject_put(&disk_to_dev(disk)->kobj);
- }
+ kobject_uevent(&q->kobj, KOBJ_REMOVE);
+ kobject_del(&q->kobj);
+ blk_trace_remove_sysfs(disk_to_dev(disk));
+ kobject_put(&disk_to_dev(disk)->kobj);
}
* idle window management
*/
struct timer_list idle_slice_timer;
- struct work_struct unplug_work;
+ struct delayed_work unplug_work;
struct cfq_queue *active_queue;
struct cfq_io_context *active_cic;
unsigned int cfq_slice[2];
unsigned int cfq_slice_async_rq;
unsigned int cfq_slice_idle;
+ unsigned int cfq_latency;
struct list_head cic_list;
* Fallback dummy cfqq for extreme OOM conditions
*/
struct cfq_queue oom_cfqq;
+
+ unsigned long last_end_sync_rq;
};
enum cfqq_state_flags {
* scheduler run of queue, if there are requests pending and no one in the
* driver that will restart queueing
*/
-static inline void cfq_schedule_dispatch(struct cfq_data *cfqd)
+static inline void cfq_schedule_dispatch(struct cfq_data *cfqd,
+ unsigned long delay)
{
if (cfqd->busy_queues) {
cfq_log(cfqd, "schedule dispatch");
- kblockd_schedule_work(cfqd->queue, &cfqd->unplug_work);
+ kblockd_schedule_delayed_work(cfqd->queue, &cfqd->unplug_work,
+ delay);
}
}
return 0;
/*
- * we are the only queue, allow up to 4 times of 'quantum'
+ * Sole queue user, allow bigger slice
*/
- if (cfqq->dispatched >= 4 * max_dispatch)
- return 0;
+ max_dispatch *= 4;
+ }
+
+ /*
+ * Async queues must wait a bit before being allowed dispatch.
+ * We also ramp up the dispatch depth gradually for async IO,
+ * based on the last sync IO we serviced
+ */
+ if (!cfq_cfqq_sync(cfqq) && cfqd->cfq_latency) {
+ unsigned long last_sync = jiffies - cfqd->last_end_sync_rq;
+ unsigned int depth;
+
+ depth = last_sync / cfqd->cfq_slice[1];
+ if (!depth && !cfqq->dispatched)
+ depth = 1;
+ if (depth < max_dispatch)
+ max_dispatch = depth;
}
+ if (cfqq->dispatched >= max_dispatch)
+ return 0;
+
/*
* Dispatch a request from this cfqq
*/
if (unlikely(cfqd->active_queue == cfqq)) {
__cfq_slice_expired(cfqd, cfqq, 0);
- cfq_schedule_dispatch(cfqd);
+ cfq_schedule_dispatch(cfqd, 0);
}
kmem_cache_free(cfq_pool, cfqq);
{
if (unlikely(cfqq == cfqd->active_queue)) {
__cfq_slice_expired(cfqd, cfqq, 0);
- cfq_schedule_dispatch(cfqd);
+ cfq_schedule_dispatch(cfqd, 0);
}
cfq_put_queue(cfqq);
enable_idle = old_idle = cfq_cfqq_idle_window(cfqq);
if (!atomic_read(&cic->ioc->nr_tasks) || !cfqd->cfq_slice_idle ||
- (cfqd->hw_tag && CIC_SEEKY(cic)))
+ (!cfqd->cfq_latency && cfqd->hw_tag && CIC_SEEKY(cic)))
enable_idle = 0;
else if (sample_valid(cic->ttime_samples)) {
if (cic->ttime_mean > cfqd->cfq_slice_idle)
if (cfq_cfqq_sync(cfqq))
cfqd->sync_flight--;
- if (sync)
+ if (sync) {
RQ_CIC(rq)->last_end_request = now;
+ cfqd->last_end_sync_rq = now;
+ }
/*
* If this is the active queue, check if it needs to be expired,
}
if (!rq_in_driver(cfqd))
- cfq_schedule_dispatch(cfqd);
+ cfq_schedule_dispatch(cfqd, 0);
}
/*
if (cic)
put_io_context(cic->ioc);
- cfq_schedule_dispatch(cfqd);
+ cfq_schedule_dispatch(cfqd, 0);
spin_unlock_irqrestore(q->queue_lock, flags);
cfq_log(cfqd, "set_request fail");
return 1;
static void cfq_kick_queue(struct work_struct *work)
{
struct cfq_data *cfqd =
- container_of(work, struct cfq_data, unplug_work);
+ container_of(work, struct cfq_data, unplug_work.work);
struct request_queue *q = cfqd->queue;
spin_lock_irq(q->queue_lock);
expire:
cfq_slice_expired(cfqd, timed_out);
out_kick:
- cfq_schedule_dispatch(cfqd);
+ cfq_schedule_dispatch(cfqd, 0);
out_cont:
spin_unlock_irqrestore(cfqd->queue->queue_lock, flags);
}
static void cfq_shutdown_timer_wq(struct cfq_data *cfqd)
{
del_timer_sync(&cfqd->idle_slice_timer);
- cancel_work_sync(&cfqd->unplug_work);
+ cancel_delayed_work_sync(&cfqd->unplug_work);
}
static void cfq_put_async_queues(struct cfq_data *cfqd)
cfqd->idle_slice_timer.function = cfq_idle_slice_timer;
cfqd->idle_slice_timer.data = (unsigned long) cfqd;
- INIT_WORK(&cfqd->unplug_work, cfq_kick_queue);
+ INIT_DELAYED_WORK(&cfqd->unplug_work, cfq_kick_queue);
cfqd->cfq_quantum = cfq_quantum;
cfqd->cfq_fifo_expire[0] = cfq_fifo_expire[0];
cfqd->cfq_slice[1] = cfq_slice_sync;
cfqd->cfq_slice_async_rq = cfq_slice_async_rq;
cfqd->cfq_slice_idle = cfq_slice_idle;
+ cfqd->cfq_latency = 1;
cfqd->hw_tag = 1;
-
+ cfqd->last_end_sync_rq = jiffies;
return cfqd;
}
SHOW_FUNCTION(cfq_slice_sync_show, cfqd->cfq_slice[1], 1);
SHOW_FUNCTION(cfq_slice_async_show, cfqd->cfq_slice[0], 1);
SHOW_FUNCTION(cfq_slice_async_rq_show, cfqd->cfq_slice_async_rq, 0);
+SHOW_FUNCTION(cfq_low_latency_show, cfqd->cfq_latency, 0);
#undef SHOW_FUNCTION
#define STORE_FUNCTION(__FUNC, __PTR, MIN, MAX, __CONV) \
STORE_FUNCTION(cfq_slice_async_store, &cfqd->cfq_slice[0], 1, UINT_MAX, 1);
STORE_FUNCTION(cfq_slice_async_rq_store, &cfqd->cfq_slice_async_rq, 1,
UINT_MAX, 0);
+STORE_FUNCTION(cfq_low_latency_store, &cfqd->cfq_latency, 0, 1, 0);
#undef STORE_FUNCTION
#define CFQ_ATTR(name) \
CFQ_ATTR(slice_async),
CFQ_ATTR(slice_async_rq),
CFQ_ATTR(slice_idle),
+ CFQ_ATTR(low_latency),
__ATTR_NULL
};
return put_user(val, (compat_int_t __user *)compat_ptr(arg));
}
+static int compat_put_uint(unsigned long arg, unsigned int val)
+{
+ return put_user(val, (compat_uint_t __user *)compat_ptr(arg));
+}
+
static int compat_put_long(unsigned long arg, long val)
{
return put_user(val, (compat_long_t __user *)compat_ptr(arg));
switch (cmd) {
case HDIO_GETGEO:
return compat_hdio_getgeo(disk, bdev, compat_ptr(arg));
+ case BLKPBSZGET:
+ return compat_put_uint(arg, bdev_physical_block_size(bdev));
+ case BLKIOMIN:
+ return compat_put_uint(arg, bdev_io_min(bdev));
+ case BLKIOOPT:
+ return compat_put_uint(arg, bdev_io_opt(bdev));
+ case BLKALIGNOFF:
+ return compat_put_int(arg, bdev_alignment_offset(bdev));
case BLKFLSBUF:
case BLKROSET:
case BLKDISCARD:
static DEVICE_ATTR(alignment_offset, S_IRUGO, disk_alignment_offset_show, NULL);
static DEVICE_ATTR(capability, S_IRUGO, disk_capability_show, NULL);
static DEVICE_ATTR(stat, S_IRUGO, part_stat_show, NULL);
-static DEVICE_ATTR(inflight, S_IRUGO, part_inflight_show, NULL);
#ifdef CONFIG_FAIL_MAKE_REQUEST
static struct device_attribute dev_attr_fail =
__ATTR(make-it-fail, S_IRUGO|S_IWUSR, part_fail_show, part_fail_store);
&dev_attr_alignment_offset.attr,
&dev_attr_capability.attr,
&dev_attr_stat.attr,
- &dev_attr_inflight.attr,
#ifdef CONFIG_FAIL_MAKE_REQUEST
&dev_attr_fail.attr,
#endif
part_stat_read(hd, merges[1]),
(unsigned long long)part_stat_read(hd, sectors[1]),
jiffies_to_msecs(part_stat_read(hd, ticks[1])),
- part_in_flight(hd),
+ hd->in_flight,
jiffies_to_msecs(part_stat_read(hd, io_ticks)),
jiffies_to_msecs(part_stat_read(hd, time_in_queue))
);
return put_user(val, (int __user *)arg);
}
+static int put_uint(unsigned long arg, unsigned int val)
+{
+ return put_user(val, (unsigned int __user *)arg);
+}
+
static int put_long(unsigned long arg, long val)
{
return put_user(val, (long __user *)arg);
return put_long(arg, (bdi->ra_pages * PAGE_CACHE_SIZE) / 512);
case BLKROGET:
return put_int(arg, bdev_read_only(bdev) != 0);
- case BLKBSZGET: /* get the logical block size (cf. BLKSSZGET) */
+ case BLKBSZGET: /* get block device soft block size (cf. BLKSSZGET) */
return put_int(arg, block_size(bdev));
- case BLKSSZGET: /* get block device hardware sector size */
+ case BLKSSZGET: /* get block device logical block size */
return put_int(arg, bdev_logical_block_size(bdev));
+ case BLKPBSZGET: /* get block device physical block size */
+ return put_uint(arg, bdev_physical_block_size(bdev));
+ case BLKIOMIN:
+ return put_uint(arg, bdev_io_min(bdev));
+ case BLKIOOPT:
+ return put_uint(arg, bdev_io_opt(bdev));
+ case BLKALIGNOFF:
+ return put_int(arg, bdev_alignment_offset(bdev));
case BLKSECTGET:
return put_ushort(arg, queue_max_sectors(bdev_get_queue(bdev)));
case BLKRASET:
tristate
select ASYNC_CORE
+config ASYNC_PQ
+ tristate
+ select ASYNC_CORE
+
+config ASYNC_RAID6_RECOV
+ tristate
+ select ASYNC_CORE
+ select ASYNC_PQ
+
obj-$(CONFIG_ASYNC_MEMCPY) += async_memcpy.o
obj-$(CONFIG_ASYNC_MEMSET) += async_memset.o
obj-$(CONFIG_ASYNC_XOR) += async_xor.o
+obj-$(CONFIG_ASYNC_PQ) += async_pq.o
+obj-$(CONFIG_ASYNC_RAID6_RECOV) += async_raid6_recov.o
+obj-$(CONFIG_ASYNC_RAID6_TEST) += raid6test.o
* async_memcpy - attempt to copy memory with a dma engine.
* @dest: destination page
* @src: src page
- * @offset: offset in pages to start transaction
+ * @dest_offset: offset into 'dest' to start transaction
+ * @src_offset: offset into 'src' to start transaction
* @len: length in bytes
- * @flags: ASYNC_TX_ACK, ASYNC_TX_DEP_ACK,
- * @depend_tx: memcpy depends on the result of this transaction
- * @cb_fn: function to call when the memcpy completes
- * @cb_param: parameter to pass to the callback routine
+ * @submit: submission / completion modifiers
+ *
+ * honored flags: ASYNC_TX_ACK
*/
struct dma_async_tx_descriptor *
async_memcpy(struct page *dest, struct page *src, unsigned int dest_offset,
- unsigned int src_offset, size_t len, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+ unsigned int src_offset, size_t len,
+ struct async_submit_ctl *submit)
{
- struct dma_chan *chan = async_tx_find_channel(depend_tx, DMA_MEMCPY,
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_MEMCPY,
&dest, 1, &src, 1, len);
struct dma_device *device = chan ? chan->device : NULL;
struct dma_async_tx_descriptor *tx = NULL;
- if (device) {
+ if (device && is_dma_copy_aligned(device, src_offset, dest_offset, len)) {
dma_addr_t dma_dest, dma_src;
- unsigned long dma_prep_flags = cb_fn ? DMA_PREP_INTERRUPT : 0;
+ unsigned long dma_prep_flags = 0;
+ if (submit->cb_fn)
+ dma_prep_flags |= DMA_PREP_INTERRUPT;
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_prep_flags |= DMA_PREP_FENCE;
dma_dest = dma_map_page(device->dev, dest, dest_offset, len,
DMA_FROM_DEVICE);
if (tx) {
pr_debug("%s: (async) len: %zu\n", __func__, len);
- async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
+ async_tx_submit(chan, tx, submit);
} else {
void *dest_buf, *src_buf;
pr_debug("%s: (sync) len: %zu\n", __func__, len);
/* wait for any prerequisite operations */
- async_tx_quiesce(&depend_tx);
+ async_tx_quiesce(&submit->depend_tx);
dest_buf = kmap_atomic(dest, KM_USER0) + dest_offset;
src_buf = kmap_atomic(src, KM_USER1) + src_offset;
kunmap_atomic(dest_buf, KM_USER0);
kunmap_atomic(src_buf, KM_USER1);
- async_tx_sync_epilog(cb_fn, cb_param);
+ async_tx_sync_epilog(submit);
}
return tx;
}
EXPORT_SYMBOL_GPL(async_memcpy);
-static int __init async_memcpy_init(void)
-{
- return 0;
-}
-
-static void __exit async_memcpy_exit(void)
-{
- do { } while (0);
-}
-
-module_init(async_memcpy_init);
-module_exit(async_memcpy_exit);
-
MODULE_AUTHOR("Intel Corporation");
MODULE_DESCRIPTION("asynchronous memcpy api");
MODULE_LICENSE("GPL");
* @val: fill value
* @offset: offset in pages to start transaction
* @len: length in bytes
- * @flags: ASYNC_TX_ACK, ASYNC_TX_DEP_ACK
- * @depend_tx: memset depends on the result of this transaction
- * @cb_fn: function to call when the memcpy completes
- * @cb_param: parameter to pass to the callback routine
+ *
+ * honored flags: ASYNC_TX_ACK
*/
struct dma_async_tx_descriptor *
-async_memset(struct page *dest, int val, unsigned int offset,
- size_t len, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+async_memset(struct page *dest, int val, unsigned int offset, size_t len,
+ struct async_submit_ctl *submit)
{
- struct dma_chan *chan = async_tx_find_channel(depend_tx, DMA_MEMSET,
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_MEMSET,
&dest, 1, NULL, 0, len);
struct dma_device *device = chan ? chan->device : NULL;
struct dma_async_tx_descriptor *tx = NULL;
- if (device) {
+ if (device && is_dma_fill_aligned(device, offset, 0, len)) {
dma_addr_t dma_dest;
- unsigned long dma_prep_flags = cb_fn ? DMA_PREP_INTERRUPT : 0;
+ unsigned long dma_prep_flags = 0;
+ if (submit->cb_fn)
+ dma_prep_flags |= DMA_PREP_INTERRUPT;
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_prep_flags |= DMA_PREP_FENCE;
dma_dest = dma_map_page(device->dev, dest, offset, len,
DMA_FROM_DEVICE);
if (tx) {
pr_debug("%s: (async) len: %zu\n", __func__, len);
- async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
+ async_tx_submit(chan, tx, submit);
} else { /* run the memset synchronously */
void *dest_buf;
pr_debug("%s: (sync) len: %zu\n", __func__, len);
- dest_buf = (void *) (((char *) page_address(dest)) + offset);
+ dest_buf = page_address(dest) + offset;
/* wait for any prerequisite operations */
- async_tx_quiesce(&depend_tx);
+ async_tx_quiesce(&submit->depend_tx);
memset(dest_buf, val, len);
- async_tx_sync_epilog(cb_fn, cb_param);
+ async_tx_sync_epilog(submit);
}
return tx;
}
EXPORT_SYMBOL_GPL(async_memset);
-static int __init async_memset_init(void)
-{
- return 0;
-}
-
-static void __exit async_memset_exit(void)
-{
- do { } while (0);
-}
-
-module_init(async_memset_init);
-module_exit(async_memset_exit);
-
MODULE_AUTHOR("Intel Corporation");
MODULE_DESCRIPTION("asynchronous memset api");
MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * Copyright(c) 2007 Yuri Tikhonov <yur@emcraft.com>
+ * Copyright(c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called COPYING.
+ */
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/raid/pq.h>
+#include <linux/async_tx.h>
+
+/**
+ * scribble - space to hold throwaway P buffer for synchronous gen_syndrome
+ */
+static struct page *scribble;
+
+static bool is_raid6_zero_block(struct page *p)
+{
+ return p == (void *) raid6_empty_zero_page;
+}
+
+/* the struct page *blocks[] parameter passed to async_gen_syndrome()
+ * and async_syndrome_val() contains the 'P' destination address at
+ * blocks[disks-2] and the 'Q' destination address at blocks[disks-1]
+ *
+ * note: these are macros as they are used as lvalues
+ */
+#define P(b, d) (b[d-2])
+#define Q(b, d) (b[d-1])
+
+/**
+ * do_async_gen_syndrome - asynchronously calculate P and/or Q
+ */
+static __async_inline struct dma_async_tx_descriptor *
+do_async_gen_syndrome(struct dma_chan *chan, struct page **blocks,
+ const unsigned char *scfs, unsigned int offset, int disks,
+ size_t len, dma_addr_t *dma_src,
+ struct async_submit_ctl *submit)
+{
+ struct dma_async_tx_descriptor *tx = NULL;
+ struct dma_device *dma = chan->device;
+ enum dma_ctrl_flags dma_flags = 0;
+ enum async_tx_flags flags_orig = submit->flags;
+ dma_async_tx_callback cb_fn_orig = submit->cb_fn;
+ dma_async_tx_callback cb_param_orig = submit->cb_param;
+ int src_cnt = disks - 2;
+ unsigned char coefs[src_cnt];
+ unsigned short pq_src_cnt;
+ dma_addr_t dma_dest[2];
+ int src_off = 0;
+ int idx;
+ int i;
+
+ /* DMAs use destinations as sources, so use BIDIRECTIONAL mapping */
+ if (P(blocks, disks))
+ dma_dest[0] = dma_map_page(dma->dev, P(blocks, disks), offset,
+ len, DMA_BIDIRECTIONAL);
+ else
+ dma_flags |= DMA_PREP_PQ_DISABLE_P;
+ if (Q(blocks, disks))
+ dma_dest[1] = dma_map_page(dma->dev, Q(blocks, disks), offset,
+ len, DMA_BIDIRECTIONAL);
+ else
+ dma_flags |= DMA_PREP_PQ_DISABLE_Q;
+
+ /* convert source addresses being careful to collapse 'empty'
+ * sources and update the coefficients accordingly
+ */
+ for (i = 0, idx = 0; i < src_cnt; i++) {
+ if (is_raid6_zero_block(blocks[i]))
+ continue;
+ dma_src[idx] = dma_map_page(dma->dev, blocks[i], offset, len,
+ DMA_TO_DEVICE);
+ coefs[idx] = scfs[i];
+ idx++;
+ }
+ src_cnt = idx;
+
+ while (src_cnt > 0) {
+ submit->flags = flags_orig;
+ pq_src_cnt = min(src_cnt, dma_maxpq(dma, dma_flags));
+ /* if we are submitting additional pqs, leave the chain open,
+ * clear the callback parameters, and leave the destination
+ * buffers mapped
+ */
+ if (src_cnt > pq_src_cnt) {
+ submit->flags &= ~ASYNC_TX_ACK;
+ submit->flags |= ASYNC_TX_FENCE;
+ dma_flags |= DMA_COMPL_SKIP_DEST_UNMAP;
+ submit->cb_fn = NULL;
+ submit->cb_param = NULL;
+ } else {
+ dma_flags &= ~DMA_COMPL_SKIP_DEST_UNMAP;
+ submit->cb_fn = cb_fn_orig;
+ submit->cb_param = cb_param_orig;
+ if (cb_fn_orig)
+ dma_flags |= DMA_PREP_INTERRUPT;
+ }
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_flags |= DMA_PREP_FENCE;
+
+ /* Since we have clobbered the src_list we are committed
+ * to doing this asynchronously. Drivers force forward
+ * progress in case they can not provide a descriptor
+ */
+ for (;;) {
+ tx = dma->device_prep_dma_pq(chan, dma_dest,
+ &dma_src[src_off],
+ pq_src_cnt,
+ &coefs[src_off], len,
+ dma_flags);
+ if (likely(tx))
+ break;
+ async_tx_quiesce(&submit->depend_tx);
+ dma_async_issue_pending(chan);
+ }
+
+ async_tx_submit(chan, tx, submit);
+ submit->depend_tx = tx;
+
+ /* drop completed sources */
+ src_cnt -= pq_src_cnt;
+ src_off += pq_src_cnt;
+
+ dma_flags |= DMA_PREP_CONTINUE;
+ }
+
+ return tx;
+}
+
+/**
+ * do_sync_gen_syndrome - synchronously calculate a raid6 syndrome
+ */
+static void
+do_sync_gen_syndrome(struct page **blocks, unsigned int offset, int disks,
+ size_t len, struct async_submit_ctl *submit)
+{
+ void **srcs;
+ int i;
+
+ if (submit->scribble)
+ srcs = submit->scribble;
+ else
+ srcs = (void **) blocks;
+
+ for (i = 0; i < disks; i++) {
+ if (is_raid6_zero_block(blocks[i])) {
+ BUG_ON(i > disks - 3); /* P or Q can't be zero */
+ srcs[i] = blocks[i];
+ } else
+ srcs[i] = page_address(blocks[i]) + offset;
+ }
+ raid6_call.gen_syndrome(disks, len, srcs);
+ async_tx_sync_epilog(submit);
+}
+
+/**
+ * async_gen_syndrome - asynchronously calculate a raid6 syndrome
+ * @blocks: source blocks from idx 0..disks-3, P @ disks-2 and Q @ disks-1
+ * @offset: common offset into each block (src and dest) to start transaction
+ * @disks: number of blocks (including missing P or Q, see below)
+ * @len: length of operation in bytes
+ * @submit: submission/completion modifiers
+ *
+ * General note: This routine assumes a field of GF(2^8) with a
+ * primitive polynomial of 0x11d and a generator of {02}.
+ *
+ * 'disks' note: callers can optionally omit either P or Q (but not
+ * both) from the calculation by setting blocks[disks-2] or
+ * blocks[disks-1] to NULL. When P or Q is omitted 'len' must be <=
+ * PAGE_SIZE as a temporary buffer of this size is used in the
+ * synchronous path. 'disks' always accounts for both destination
+ * buffers.
+ *
+ * 'blocks' note: if submit->scribble is NULL then the contents of
+ * 'blocks' may be overridden
+ */
+struct dma_async_tx_descriptor *
+async_gen_syndrome(struct page **blocks, unsigned int offset, int disks,
+ size_t len, struct async_submit_ctl *submit)
+{
+ int src_cnt = disks - 2;
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_PQ,
+ &P(blocks, disks), 2,
+ blocks, src_cnt, len);
+ struct dma_device *device = chan ? chan->device : NULL;
+ dma_addr_t *dma_src = NULL;
+
+ BUG_ON(disks > 255 || !(P(blocks, disks) || Q(blocks, disks)));
+
+ if (submit->scribble)
+ dma_src = submit->scribble;
+ else if (sizeof(dma_addr_t) <= sizeof(struct page *))
+ dma_src = (dma_addr_t *) blocks;
+
+ if (dma_src && device &&
+ (src_cnt <= dma_maxpq(device, 0) ||
+ dma_maxpq(device, DMA_PREP_CONTINUE) > 0) &&
+ is_dma_pq_aligned(device, offset, 0, len)) {
+ /* run the p+q asynchronously */
+ pr_debug("%s: (async) disks: %d len: %zu\n",
+ __func__, disks, len);
+ return do_async_gen_syndrome(chan, blocks, raid6_gfexp, offset,
+ disks, len, dma_src, submit);
+ }
+
+ /* run the pq synchronously */
+ pr_debug("%s: (sync) disks: %d len: %zu\n", __func__, disks, len);
+
+ /* wait for any prerequisite operations */
+ async_tx_quiesce(&submit->depend_tx);
+
+ if (!P(blocks, disks)) {
+ P(blocks, disks) = scribble;
+ BUG_ON(len + offset > PAGE_SIZE);
+ }
+ if (!Q(blocks, disks)) {
+ Q(blocks, disks) = scribble;
+ BUG_ON(len + offset > PAGE_SIZE);
+ }
+ do_sync_gen_syndrome(blocks, offset, disks, len, submit);
+
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(async_gen_syndrome);
+
+/**
+ * async_syndrome_val - asynchronously validate a raid6 syndrome
+ * @blocks: source blocks from idx 0..disks-3, P @ disks-2 and Q @ disks-1
+ * @offset: common offset into each block (src and dest) to start transaction
+ * @disks: number of blocks (including missing P or Q, see below)
+ * @len: length of operation in bytes
+ * @pqres: on val failure SUM_CHECK_P_RESULT and/or SUM_CHECK_Q_RESULT are set
+ * @spare: temporary result buffer for the synchronous case
+ * @submit: submission / completion modifiers
+ *
+ * The same notes from async_gen_syndrome apply to the 'blocks',
+ * and 'disks' parameters of this routine. The synchronous path
+ * requires a temporary result buffer and submit->scribble to be
+ * specified.
+ */
+struct dma_async_tx_descriptor *
+async_syndrome_val(struct page **blocks, unsigned int offset, int disks,
+ size_t len, enum sum_check_flags *pqres, struct page *spare,
+ struct async_submit_ctl *submit)
+{
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_PQ_VAL,
+ NULL, 0, blocks, disks,
+ len);
+ struct dma_device *device = chan ? chan->device : NULL;
+ struct dma_async_tx_descriptor *tx;
+ enum dma_ctrl_flags dma_flags = submit->cb_fn ? DMA_PREP_INTERRUPT : 0;
+ dma_addr_t *dma_src = NULL;
+
+ BUG_ON(disks < 4);
+
+ if (submit->scribble)
+ dma_src = submit->scribble;
+ else if (sizeof(dma_addr_t) <= sizeof(struct page *))
+ dma_src = (dma_addr_t *) blocks;
+
+ if (dma_src && device && disks <= dma_maxpq(device, 0) &&
+ is_dma_pq_aligned(device, offset, 0, len)) {
+ struct device *dev = device->dev;
+ dma_addr_t *pq = &dma_src[disks-2];
+ int i;
+
+ pr_debug("%s: (async) disks: %d len: %zu\n",
+ __func__, disks, len);
+ if (!P(blocks, disks))
+ dma_flags |= DMA_PREP_PQ_DISABLE_P;
+ if (!Q(blocks, disks))
+ dma_flags |= DMA_PREP_PQ_DISABLE_Q;
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_flags |= DMA_PREP_FENCE;
+ for (i = 0; i < disks; i++)
+ if (likely(blocks[i])) {
+ BUG_ON(is_raid6_zero_block(blocks[i]));
+ dma_src[i] = dma_map_page(dev, blocks[i],
+ offset, len,
+ DMA_TO_DEVICE);
+ }
+
+ for (;;) {
+ tx = device->device_prep_dma_pq_val(chan, pq, dma_src,
+ disks - 2,
+ raid6_gfexp,
+ len, pqres,
+ dma_flags);
+ if (likely(tx))
+ break;
+ async_tx_quiesce(&submit->depend_tx);
+ dma_async_issue_pending(chan);
+ }
+ async_tx_submit(chan, tx, submit);
+
+ return tx;
+ } else {
+ struct page *p_src = P(blocks, disks);
+ struct page *q_src = Q(blocks, disks);
+ enum async_tx_flags flags_orig = submit->flags;
+ dma_async_tx_callback cb_fn_orig = submit->cb_fn;
+ void *scribble = submit->scribble;
+ void *cb_param_orig = submit->cb_param;
+ void *p, *q, *s;
+
+ pr_debug("%s: (sync) disks: %d len: %zu\n",
+ __func__, disks, len);
+
+ /* caller must provide a temporary result buffer and
+ * allow the input parameters to be preserved
+ */
+ BUG_ON(!spare || !scribble);
+
+ /* wait for any prerequisite operations */
+ async_tx_quiesce(&submit->depend_tx);
+
+ /* recompute p and/or q into the temporary buffer and then
+ * check to see the result matches the current value
+ */
+ tx = NULL;
+ *pqres = 0;
+ if (p_src) {
+ init_async_submit(submit, ASYNC_TX_XOR_ZERO_DST, NULL,
+ NULL, NULL, scribble);
+ tx = async_xor(spare, blocks, offset, disks-2, len, submit);
+ async_tx_quiesce(&tx);
+ p = page_address(p_src) + offset;
+ s = page_address(spare) + offset;
+ *pqres |= !!memcmp(p, s, len) << SUM_CHECK_P;
+ }
+
+ if (q_src) {
+ P(blocks, disks) = NULL;
+ Q(blocks, disks) = spare;
+ init_async_submit(submit, 0, NULL, NULL, NULL, scribble);
+ tx = async_gen_syndrome(blocks, offset, disks, len, submit);
+ async_tx_quiesce(&tx);
+ q = page_address(q_src) + offset;
+ s = page_address(spare) + offset;
+ *pqres |= !!memcmp(q, s, len) << SUM_CHECK_Q;
+ }
+
+ /* restore P, Q and submit */
+ P(blocks, disks) = p_src;
+ Q(blocks, disks) = q_src;
+
+ submit->cb_fn = cb_fn_orig;
+ submit->cb_param = cb_param_orig;
+ submit->flags = flags_orig;
+ async_tx_sync_epilog(submit);
+
+ return NULL;
+ }
+}
+EXPORT_SYMBOL_GPL(async_syndrome_val);
+
+static int __init async_pq_init(void)
+{
+ scribble = alloc_page(GFP_KERNEL);
+
+ if (scribble)
+ return 0;
+
+ pr_err("%s: failed to allocate required spare page\n", __func__);
+
+ return -ENOMEM;
+}
+
+static void __exit async_pq_exit(void)
+{
+ put_page(scribble);
+}
+
+module_init(async_pq_init);
+module_exit(async_pq_exit);
+
+MODULE_DESCRIPTION("asynchronous raid6 syndrome generation/validation");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * Asynchronous RAID-6 recovery calculations ASYNC_TX API.
+ * Copyright(c) 2009 Intel Corporation
+ *
+ * based on raid6recov.c:
+ * Copyright 2002 H. Peter Anvin
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 51
+ * Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/raid/pq.h>
+#include <linux/async_tx.h>
+
+static struct dma_async_tx_descriptor *
+async_sum_product(struct page *dest, struct page **srcs, unsigned char *coef,
+ size_t len, struct async_submit_ctl *submit)
+{
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_PQ,
+ &dest, 1, srcs, 2, len);
+ struct dma_device *dma = chan ? chan->device : NULL;
+ const u8 *amul, *bmul;
+ u8 ax, bx;
+ u8 *a, *b, *c;
+
+ if (dma) {
+ dma_addr_t dma_dest[2];
+ dma_addr_t dma_src[2];
+ struct device *dev = dma->dev;
+ struct dma_async_tx_descriptor *tx;
+ enum dma_ctrl_flags dma_flags = DMA_PREP_PQ_DISABLE_P;
+
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_flags |= DMA_PREP_FENCE;
+ dma_dest[1] = dma_map_page(dev, dest, 0, len, DMA_BIDIRECTIONAL);
+ dma_src[0] = dma_map_page(dev, srcs[0], 0, len, DMA_TO_DEVICE);
+ dma_src[1] = dma_map_page(dev, srcs[1], 0, len, DMA_TO_DEVICE);
+ tx = dma->device_prep_dma_pq(chan, dma_dest, dma_src, 2, coef,
+ len, dma_flags);
+ if (tx) {
+ async_tx_submit(chan, tx, submit);
+ return tx;
+ }
+
+ /* could not get a descriptor, unmap and fall through to
+ * the synchronous path
+ */
+ dma_unmap_page(dev, dma_dest[1], len, DMA_BIDIRECTIONAL);
+ dma_unmap_page(dev, dma_src[0], len, DMA_TO_DEVICE);
+ dma_unmap_page(dev, dma_src[1], len, DMA_TO_DEVICE);
+ }
+
+ /* run the operation synchronously */
+ async_tx_quiesce(&submit->depend_tx);
+ amul = raid6_gfmul[coef[0]];
+ bmul = raid6_gfmul[coef[1]];
+ a = page_address(srcs[0]);
+ b = page_address(srcs[1]);
+ c = page_address(dest);
+
+ while (len--) {
+ ax = amul[*a++];
+ bx = bmul[*b++];
+ *c++ = ax ^ bx;
+ }
+
+ return NULL;
+}
+
+static struct dma_async_tx_descriptor *
+async_mult(struct page *dest, struct page *src, u8 coef, size_t len,
+ struct async_submit_ctl *submit)
+{
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_PQ,
+ &dest, 1, &src, 1, len);
+ struct dma_device *dma = chan ? chan->device : NULL;
+ const u8 *qmul; /* Q multiplier table */
+ u8 *d, *s;
+
+ if (dma) {
+ dma_addr_t dma_dest[2];
+ dma_addr_t dma_src[1];
+ struct device *dev = dma->dev;
+ struct dma_async_tx_descriptor *tx;
+ enum dma_ctrl_flags dma_flags = DMA_PREP_PQ_DISABLE_P;
+
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_flags |= DMA_PREP_FENCE;
+ dma_dest[1] = dma_map_page(dev, dest, 0, len, DMA_BIDIRECTIONAL);
+ dma_src[0] = dma_map_page(dev, src, 0, len, DMA_TO_DEVICE);
+ tx = dma->device_prep_dma_pq(chan, dma_dest, dma_src, 1, &coef,
+ len, dma_flags);
+ if (tx) {
+ async_tx_submit(chan, tx, submit);
+ return tx;
+ }
+
+ /* could not get a descriptor, unmap and fall through to
+ * the synchronous path
+ */
+ dma_unmap_page(dev, dma_dest[1], len, DMA_BIDIRECTIONAL);
+ dma_unmap_page(dev, dma_src[0], len, DMA_TO_DEVICE);
+ }
+
+ /* no channel available, or failed to allocate a descriptor, so
+ * perform the operation synchronously
+ */
+ async_tx_quiesce(&submit->depend_tx);
+ qmul = raid6_gfmul[coef];
+ d = page_address(dest);
+ s = page_address(src);
+
+ while (len--)
+ *d++ = qmul[*s++];
+
+ return NULL;
+}
+
+static struct dma_async_tx_descriptor *
+__2data_recov_4(size_t bytes, int faila, int failb, struct page **blocks,
+ struct async_submit_ctl *submit)
+{
+ struct dma_async_tx_descriptor *tx = NULL;
+ struct page *p, *q, *a, *b;
+ struct page *srcs[2];
+ unsigned char coef[2];
+ enum async_tx_flags flags = submit->flags;
+ dma_async_tx_callback cb_fn = submit->cb_fn;
+ void *cb_param = submit->cb_param;
+ void *scribble = submit->scribble;
+
+ p = blocks[4-2];
+ q = blocks[4-1];
+
+ a = blocks[faila];
+ b = blocks[failb];
+
+ /* in the 4 disk case P + Pxy == P and Q + Qxy == Q */
+ /* Dx = A*(P+Pxy) + B*(Q+Qxy) */
+ srcs[0] = p;
+ srcs[1] = q;
+ coef[0] = raid6_gfexi[failb-faila];
+ coef[1] = raid6_gfinv[raid6_gfexp[faila]^raid6_gfexp[failb]];
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_sum_product(b, srcs, coef, bytes, submit);
+
+ /* Dy = P+Pxy+Dx */
+ srcs[0] = p;
+ srcs[1] = b;
+ init_async_submit(submit, flags | ASYNC_TX_XOR_ZERO_DST, tx, cb_fn,
+ cb_param, scribble);
+ tx = async_xor(a, srcs, 0, 2, bytes, submit);
+
+ return tx;
+
+}
+
+static struct dma_async_tx_descriptor *
+__2data_recov_5(size_t bytes, int faila, int failb, struct page **blocks,
+ struct async_submit_ctl *submit)
+{
+ struct dma_async_tx_descriptor *tx = NULL;
+ struct page *p, *q, *g, *dp, *dq;
+ struct page *srcs[2];
+ unsigned char coef[2];
+ enum async_tx_flags flags = submit->flags;
+ dma_async_tx_callback cb_fn = submit->cb_fn;
+ void *cb_param = submit->cb_param;
+ void *scribble = submit->scribble;
+ int uninitialized_var(good);
+ int i;
+
+ for (i = 0; i < 3; i++) {
+ if (i == faila || i == failb)
+ continue;
+ else {
+ good = i;
+ break;
+ }
+ }
+ BUG_ON(i >= 3);
+
+ p = blocks[5-2];
+ q = blocks[5-1];
+ g = blocks[good];
+
+ /* Compute syndrome with zero for the missing data pages
+ * Use the dead data pages as temporary storage for delta p and
+ * delta q
+ */
+ dp = blocks[faila];
+ dq = blocks[failb];
+
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_memcpy(dp, g, 0, 0, bytes, submit);
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_mult(dq, g, raid6_gfexp[good], bytes, submit);
+
+ /* compute P + Pxy */
+ srcs[0] = dp;
+ srcs[1] = p;
+ init_async_submit(submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_DROP_DST, tx,
+ NULL, NULL, scribble);
+ tx = async_xor(dp, srcs, 0, 2, bytes, submit);
+
+ /* compute Q + Qxy */
+ srcs[0] = dq;
+ srcs[1] = q;
+ init_async_submit(submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_DROP_DST, tx,
+ NULL, NULL, scribble);
+ tx = async_xor(dq, srcs, 0, 2, bytes, submit);
+
+ /* Dx = A*(P+Pxy) + B*(Q+Qxy) */
+ srcs[0] = dp;
+ srcs[1] = dq;
+ coef[0] = raid6_gfexi[failb-faila];
+ coef[1] = raid6_gfinv[raid6_gfexp[faila]^raid6_gfexp[failb]];
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_sum_product(dq, srcs, coef, bytes, submit);
+
+ /* Dy = P+Pxy+Dx */
+ srcs[0] = dp;
+ srcs[1] = dq;
+ init_async_submit(submit, flags | ASYNC_TX_XOR_DROP_DST, tx, cb_fn,
+ cb_param, scribble);
+ tx = async_xor(dp, srcs, 0, 2, bytes, submit);
+
+ return tx;
+}
+
+static struct dma_async_tx_descriptor *
+__2data_recov_n(int disks, size_t bytes, int faila, int failb,
+ struct page **blocks, struct async_submit_ctl *submit)
+{
+ struct dma_async_tx_descriptor *tx = NULL;
+ struct page *p, *q, *dp, *dq;
+ struct page *srcs[2];
+ unsigned char coef[2];
+ enum async_tx_flags flags = submit->flags;
+ dma_async_tx_callback cb_fn = submit->cb_fn;
+ void *cb_param = submit->cb_param;
+ void *scribble = submit->scribble;
+
+ p = blocks[disks-2];
+ q = blocks[disks-1];
+
+ /* Compute syndrome with zero for the missing data pages
+ * Use the dead data pages as temporary storage for
+ * delta p and delta q
+ */
+ dp = blocks[faila];
+ blocks[faila] = (void *)raid6_empty_zero_page;
+ blocks[disks-2] = dp;
+ dq = blocks[failb];
+ blocks[failb] = (void *)raid6_empty_zero_page;
+ blocks[disks-1] = dq;
+
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_gen_syndrome(blocks, 0, disks, bytes, submit);
+
+ /* Restore pointer table */
+ blocks[faila] = dp;
+ blocks[failb] = dq;
+ blocks[disks-2] = p;
+ blocks[disks-1] = q;
+
+ /* compute P + Pxy */
+ srcs[0] = dp;
+ srcs[1] = p;
+ init_async_submit(submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_DROP_DST, tx,
+ NULL, NULL, scribble);
+ tx = async_xor(dp, srcs, 0, 2, bytes, submit);
+
+ /* compute Q + Qxy */
+ srcs[0] = dq;
+ srcs[1] = q;
+ init_async_submit(submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_DROP_DST, tx,
+ NULL, NULL, scribble);
+ tx = async_xor(dq, srcs, 0, 2, bytes, submit);
+
+ /* Dx = A*(P+Pxy) + B*(Q+Qxy) */
+ srcs[0] = dp;
+ srcs[1] = dq;
+ coef[0] = raid6_gfexi[failb-faila];
+ coef[1] = raid6_gfinv[raid6_gfexp[faila]^raid6_gfexp[failb]];
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_sum_product(dq, srcs, coef, bytes, submit);
+
+ /* Dy = P+Pxy+Dx */
+ srcs[0] = dp;
+ srcs[1] = dq;
+ init_async_submit(submit, flags | ASYNC_TX_XOR_DROP_DST, tx, cb_fn,
+ cb_param, scribble);
+ tx = async_xor(dp, srcs, 0, 2, bytes, submit);
+
+ return tx;
+}
+
+/**
+ * async_raid6_2data_recov - asynchronously calculate two missing data blocks
+ * @disks: number of disks in the RAID-6 array
+ * @bytes: block size
+ * @faila: first failed drive index
+ * @failb: second failed drive index
+ * @blocks: array of source pointers where the last two entries are p and q
+ * @submit: submission/completion modifiers
+ */
+struct dma_async_tx_descriptor *
+async_raid6_2data_recov(int disks, size_t bytes, int faila, int failb,
+ struct page **blocks, struct async_submit_ctl *submit)
+{
+ BUG_ON(faila == failb);
+ if (failb < faila)
+ swap(faila, failb);
+
+ pr_debug("%s: disks: %d len: %zu\n", __func__, disks, bytes);
+
+ /* we need to preserve the contents of 'blocks' for the async
+ * case, so punt to synchronous if a scribble buffer is not available
+ */
+ if (!submit->scribble) {
+ void **ptrs = (void **) blocks;
+ int i;
+
+ async_tx_quiesce(&submit->depend_tx);
+ for (i = 0; i < disks; i++)
+ ptrs[i] = page_address(blocks[i]);
+
+ raid6_2data_recov(disks, bytes, faila, failb, ptrs);
+
+ async_tx_sync_epilog(submit);
+
+ return NULL;
+ }
+
+ switch (disks) {
+ case 4:
+ /* dma devices do not uniformly understand a zero source pq
+ * operation (in contrast to the synchronous case), so
+ * explicitly handle the 4 disk special case
+ */
+ return __2data_recov_4(bytes, faila, failb, blocks, submit);
+ case 5:
+ /* dma devices do not uniformly understand a single
+ * source pq operation (in contrast to the synchronous
+ * case), so explicitly handle the 5 disk special case
+ */
+ return __2data_recov_5(bytes, faila, failb, blocks, submit);
+ default:
+ return __2data_recov_n(disks, bytes, faila, failb, blocks, submit);
+ }
+}
+EXPORT_SYMBOL_GPL(async_raid6_2data_recov);
+
+/**
+ * async_raid6_datap_recov - asynchronously calculate a data and the 'p' block
+ * @disks: number of disks in the RAID-6 array
+ * @bytes: block size
+ * @faila: failed drive index
+ * @blocks: array of source pointers where the last two entries are p and q
+ * @submit: submission/completion modifiers
+ */
+struct dma_async_tx_descriptor *
+async_raid6_datap_recov(int disks, size_t bytes, int faila,
+ struct page **blocks, struct async_submit_ctl *submit)
+{
+ struct dma_async_tx_descriptor *tx = NULL;
+ struct page *p, *q, *dq;
+ u8 coef;
+ enum async_tx_flags flags = submit->flags;
+ dma_async_tx_callback cb_fn = submit->cb_fn;
+ void *cb_param = submit->cb_param;
+ void *scribble = submit->scribble;
+ struct page *srcs[2];
+
+ pr_debug("%s: disks: %d len: %zu\n", __func__, disks, bytes);
+
+ /* we need to preserve the contents of 'blocks' for the async
+ * case, so punt to synchronous if a scribble buffer is not available
+ */
+ if (!scribble) {
+ void **ptrs = (void **) blocks;
+ int i;
+
+ async_tx_quiesce(&submit->depend_tx);
+ for (i = 0; i < disks; i++)
+ ptrs[i] = page_address(blocks[i]);
+
+ raid6_datap_recov(disks, bytes, faila, ptrs);
+
+ async_tx_sync_epilog(submit);
+
+ return NULL;
+ }
+
+ p = blocks[disks-2];
+ q = blocks[disks-1];
+
+ /* Compute syndrome with zero for the missing data page
+ * Use the dead data page as temporary storage for delta q
+ */
+ dq = blocks[faila];
+ blocks[faila] = (void *)raid6_empty_zero_page;
+ blocks[disks-1] = dq;
+
+ /* in the 4 disk case we only need to perform a single source
+ * multiplication
+ */
+ if (disks == 4) {
+ int good = faila == 0 ? 1 : 0;
+ struct page *g = blocks[good];
+
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL,
+ scribble);
+ tx = async_memcpy(p, g, 0, 0, bytes, submit);
+
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL,
+ scribble);
+ tx = async_mult(dq, g, raid6_gfexp[good], bytes, submit);
+ } else {
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL,
+ scribble);
+ tx = async_gen_syndrome(blocks, 0, disks, bytes, submit);
+ }
+
+ /* Restore pointer table */
+ blocks[faila] = dq;
+ blocks[disks-1] = q;
+
+ /* calculate g^{-faila} */
+ coef = raid6_gfinv[raid6_gfexp[faila]];
+
+ srcs[0] = dq;
+ srcs[1] = q;
+ init_async_submit(submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_DROP_DST, tx,
+ NULL, NULL, scribble);
+ tx = async_xor(dq, srcs, 0, 2, bytes, submit);
+
+ init_async_submit(submit, ASYNC_TX_FENCE, tx, NULL, NULL, scribble);
+ tx = async_mult(dq, dq, coef, bytes, submit);
+
+ srcs[0] = p;
+ srcs[1] = dq;
+ init_async_submit(submit, flags | ASYNC_TX_XOR_DROP_DST, tx, cb_fn,
+ cb_param, scribble);
+ tx = async_xor(p, srcs, 0, 2, bytes, submit);
+
+ return tx;
+}
+EXPORT_SYMBOL_GPL(async_raid6_datap_recov);
+
+MODULE_AUTHOR("Dan Williams <dan.j.williams@intel.com>");
+MODULE_DESCRIPTION("asynchronous RAID-6 recovery api");
+MODULE_LICENSE("GPL");
async_dmaengine_put();
}
+module_init(async_tx_init);
+module_exit(async_tx_exit);
+
/**
* __async_tx_find_channel - find a channel to carry out the operation or let
* the transaction execute synchronously
- * @depend_tx: transaction dependency
+ * @submit: transaction dependency and submission modifiers
* @tx_type: transaction type
*/
struct dma_chan *
-__async_tx_find_channel(struct dma_async_tx_descriptor *depend_tx,
- enum dma_transaction_type tx_type)
+__async_tx_find_channel(struct async_submit_ctl *submit,
+ enum dma_transaction_type tx_type)
{
+ struct dma_async_tx_descriptor *depend_tx = submit->depend_tx;
+
/* see if we can keep the chain on one channel */
if (depend_tx &&
dma_has_cap(tx_type, depend_tx->chan->device->cap_mask))
return async_dma_find_channel(tx_type);
}
EXPORT_SYMBOL_GPL(__async_tx_find_channel);
-#else
-static int __init async_tx_init(void)
-{
- printk(KERN_INFO "async_tx: api initialized (sync-only)\n");
- return 0;
-}
-
-static void __exit async_tx_exit(void)
-{
- do { } while (0);
-}
#endif
async_tx_channel_switch(struct dma_async_tx_descriptor *depend_tx,
struct dma_async_tx_descriptor *tx)
{
- struct dma_chan *chan;
- struct dma_device *device;
+ struct dma_chan *chan = depend_tx->chan;
+ struct dma_device *device = chan->device;
struct dma_async_tx_descriptor *intr_tx = (void *) ~0;
+ #ifdef CONFIG_ASYNC_TX_DISABLE_CHANNEL_SWITCH
+ BUG();
+ #endif
+
/* first check to see if we can still append to depend_tx */
spin_lock_bh(&depend_tx->lock);
if (depend_tx->parent && depend_tx->chan == tx->chan) {
}
spin_unlock_bh(&depend_tx->lock);
- if (!intr_tx)
+ /* attached dependency, flush the parent channel */
+ if (!intr_tx) {
+ device->device_issue_pending(chan);
return;
-
- chan = depend_tx->chan;
- device = chan->device;
+ }
/* see if we can schedule an interrupt
* otherwise poll for completion
intr_tx->tx_submit(intr_tx);
async_tx_ack(intr_tx);
}
+ device->device_issue_pending(chan);
} else {
if (dma_wait_for_async_tx(depend_tx) == DMA_ERROR)
panic("%s: DMA_ERROR waiting for depend_tx\n",
/**
- * submit_disposition - while holding depend_tx->lock we must avoid submitting
- * new operations to prevent a circular locking dependency with
- * drivers that already hold a channel lock when calling
- * async_tx_run_dependencies.
+ * submit_disposition - flags for routing an incoming operation
* @ASYNC_TX_SUBMITTED: we were able to append the new operation under the lock
* @ASYNC_TX_CHANNEL_SWITCH: when the lock is dropped schedule a channel switch
* @ASYNC_TX_DIRECT_SUBMIT: when the lock is dropped submit directly
+ *
+ * while holding depend_tx->lock we must avoid submitting new operations
+ * to prevent a circular locking dependency with drivers that already
+ * hold a channel lock when calling async_tx_run_dependencies.
*/
enum submit_disposition {
ASYNC_TX_SUBMITTED,
void
async_tx_submit(struct dma_chan *chan, struct dma_async_tx_descriptor *tx,
- enum async_tx_flags flags, struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+ struct async_submit_ctl *submit)
{
- tx->callback = cb_fn;
- tx->callback_param = cb_param;
+ struct dma_async_tx_descriptor *depend_tx = submit->depend_tx;
+
+ tx->callback = submit->cb_fn;
+ tx->callback_param = submit->cb_param;
if (depend_tx) {
enum submit_disposition s;
tx->tx_submit(tx);
}
- if (flags & ASYNC_TX_ACK)
+ if (submit->flags & ASYNC_TX_ACK)
async_tx_ack(tx);
- if (depend_tx && (flags & ASYNC_TX_DEP_ACK))
+ if (depend_tx)
async_tx_ack(depend_tx);
}
EXPORT_SYMBOL_GPL(async_tx_submit);
/**
- * async_trigger_callback - schedules the callback function to be run after
- * any dependent operations have been completed.
- * @flags: ASYNC_TX_ACK, ASYNC_TX_DEP_ACK
- * @depend_tx: 'callback' requires the completion of this transaction
- * @cb_fn: function to call after depend_tx completes
- * @cb_param: parameter to pass to the callback routine
+ * async_trigger_callback - schedules the callback function to be run
+ * @submit: submission and completion parameters
+ *
+ * honored flags: ASYNC_TX_ACK
+ *
+ * The callback is run after any dependent operations have completed.
*/
struct dma_async_tx_descriptor *
-async_trigger_callback(enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+async_trigger_callback(struct async_submit_ctl *submit)
{
struct dma_chan *chan;
struct dma_device *device;
struct dma_async_tx_descriptor *tx;
+ struct dma_async_tx_descriptor *depend_tx = submit->depend_tx;
if (depend_tx) {
chan = depend_tx->chan;
if (tx) {
pr_debug("%s: (async)\n", __func__);
- async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
+ async_tx_submit(chan, tx, submit);
} else {
pr_debug("%s: (sync)\n", __func__);
/* wait for any prerequisite operations */
- async_tx_quiesce(&depend_tx);
+ async_tx_quiesce(&submit->depend_tx);
- async_tx_sync_epilog(cb_fn, cb_param);
+ async_tx_sync_epilog(submit);
}
return tx;
}
EXPORT_SYMBOL_GPL(async_tx_quiesce);
-module_init(async_tx_init);
-module_exit(async_tx_exit);
-
MODULE_AUTHOR("Intel Corporation");
MODULE_DESCRIPTION("Asynchronous Bulk Memory Transactions API");
MODULE_LICENSE("GPL");
/* do_async_xor - dma map the pages and perform the xor with an engine */
static __async_inline struct dma_async_tx_descriptor *
do_async_xor(struct dma_chan *chan, struct page *dest, struct page **src_list,
- unsigned int offset, int src_cnt, size_t len,
- enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+ unsigned int offset, int src_cnt, size_t len, dma_addr_t *dma_src,
+ struct async_submit_ctl *submit)
{
struct dma_device *dma = chan->device;
- dma_addr_t *dma_src = (dma_addr_t *) src_list;
struct dma_async_tx_descriptor *tx = NULL;
int src_off = 0;
int i;
- dma_async_tx_callback _cb_fn;
- void *_cb_param;
- enum async_tx_flags async_flags;
+ dma_async_tx_callback cb_fn_orig = submit->cb_fn;
+ void *cb_param_orig = submit->cb_param;
+ enum async_tx_flags flags_orig = submit->flags;
enum dma_ctrl_flags dma_flags;
int xor_src_cnt;
dma_addr_t dma_dest;
}
while (src_cnt) {
- async_flags = flags;
+ submit->flags = flags_orig;
dma_flags = 0;
- xor_src_cnt = min(src_cnt, dma->max_xor);
+ xor_src_cnt = min(src_cnt, (int)dma->max_xor);
/* if we are submitting additional xors, leave the chain open,
* clear the callback parameters, and leave the destination
* buffer mapped
*/
if (src_cnt > xor_src_cnt) {
- async_flags &= ~ASYNC_TX_ACK;
+ submit->flags &= ~ASYNC_TX_ACK;
+ submit->flags |= ASYNC_TX_FENCE;
dma_flags = DMA_COMPL_SKIP_DEST_UNMAP;
- _cb_fn = NULL;
- _cb_param = NULL;
+ submit->cb_fn = NULL;
+ submit->cb_param = NULL;
} else {
- _cb_fn = cb_fn;
- _cb_param = cb_param;
+ submit->cb_fn = cb_fn_orig;
+ submit->cb_param = cb_param_orig;
}
- if (_cb_fn)
+ if (submit->cb_fn)
dma_flags |= DMA_PREP_INTERRUPT;
-
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_flags |= DMA_PREP_FENCE;
/* Since we have clobbered the src_list we are committed
* to doing this asynchronously. Drivers force forward progress
* in case they can not provide a descriptor
xor_src_cnt, len, dma_flags);
if (unlikely(!tx))
- async_tx_quiesce(&depend_tx);
+ async_tx_quiesce(&submit->depend_tx);
/* spin wait for the preceeding transactions to complete */
while (unlikely(!tx)) {
dma_flags);
}
- async_tx_submit(chan, tx, async_flags, depend_tx, _cb_fn,
- _cb_param);
-
- depend_tx = tx;
- flags |= ASYNC_TX_DEP_ACK;
+ async_tx_submit(chan, tx, submit);
+ submit->depend_tx = tx;
if (src_cnt > xor_src_cnt) {
/* drop completed sources */
static void
do_sync_xor(struct page *dest, struct page **src_list, unsigned int offset,
- int src_cnt, size_t len, enum async_tx_flags flags,
- dma_async_tx_callback cb_fn, void *cb_param)
+ int src_cnt, size_t len, struct async_submit_ctl *submit)
{
int i;
int xor_src_cnt;
int src_off = 0;
void *dest_buf;
- void **srcs = (void **) src_list;
+ void **srcs;
+
+ if (submit->scribble)
+ srcs = submit->scribble;
+ else
+ srcs = (void **) src_list;
- /* reuse the 'src_list' array to convert to buffer pointers */
+ /* convert to buffer pointers */
for (i = 0; i < src_cnt; i++)
srcs[i] = page_address(src_list[i]) + offset;
/* set destination address */
dest_buf = page_address(dest) + offset;
- if (flags & ASYNC_TX_XOR_ZERO_DST)
+ if (submit->flags & ASYNC_TX_XOR_ZERO_DST)
memset(dest_buf, 0, len);
while (src_cnt > 0) {
src_off += xor_src_cnt;
}
- async_tx_sync_epilog(cb_fn, cb_param);
+ async_tx_sync_epilog(submit);
}
/**
* async_xor - attempt to xor a set of blocks with a dma engine.
- * xor_blocks always uses the dest as a source so the ASYNC_TX_XOR_ZERO_DST
- * flag must be set to not include dest data in the calculation. The
- * assumption with dma eninges is that they only use the destination
- * buffer as a source when it is explicity specified in the source list.
* @dest: destination page
- * @src_list: array of source pages (if the dest is also a source it must be
- * at index zero). The contents of this array may be overwritten.
- * @offset: offset in pages to start transaction
+ * @src_list: array of source pages
+ * @offset: common src/dst offset to start transaction
* @src_cnt: number of source pages
* @len: length in bytes
- * @flags: ASYNC_TX_XOR_ZERO_DST, ASYNC_TX_XOR_DROP_DEST,
- * ASYNC_TX_ACK, ASYNC_TX_DEP_ACK
- * @depend_tx: xor depends on the result of this transaction.
- * @cb_fn: function to call when the xor completes
- * @cb_param: parameter to pass to the callback routine
+ * @submit: submission / completion modifiers
+ *
+ * honored flags: ASYNC_TX_ACK, ASYNC_TX_XOR_ZERO_DST, ASYNC_TX_XOR_DROP_DST
+ *
+ * xor_blocks always uses the dest as a source so the
+ * ASYNC_TX_XOR_ZERO_DST flag must be set to not include dest data in
+ * the calculation. The assumption with dma eninges is that they only
+ * use the destination buffer as a source when it is explicity specified
+ * in the source list.
+ *
+ * src_list note: if the dest is also a source it must be at index zero.
+ * The contents of this array will be overwritten if a scribble region
+ * is not specified.
*/
struct dma_async_tx_descriptor *
async_xor(struct page *dest, struct page **src_list, unsigned int offset,
- int src_cnt, size_t len, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+ int src_cnt, size_t len, struct async_submit_ctl *submit)
{
- struct dma_chan *chan = async_tx_find_channel(depend_tx, DMA_XOR,
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_XOR,
&dest, 1, src_list,
src_cnt, len);
+ dma_addr_t *dma_src = NULL;
+
BUG_ON(src_cnt <= 1);
- if (chan) {
+ if (submit->scribble)
+ dma_src = submit->scribble;
+ else if (sizeof(dma_addr_t) <= sizeof(struct page *))
+ dma_src = (dma_addr_t *) src_list;
+
+ if (dma_src && chan && is_dma_xor_aligned(chan->device, offset, 0, len)) {
/* run the xor asynchronously */
pr_debug("%s (async): len: %zu\n", __func__, len);
return do_async_xor(chan, dest, src_list, offset, src_cnt, len,
- flags, depend_tx, cb_fn, cb_param);
+ dma_src, submit);
} else {
/* run the xor synchronously */
pr_debug("%s (sync): len: %zu\n", __func__, len);
+ WARN_ONCE(chan, "%s: no space for dma address conversion\n",
+ __func__);
/* in the sync case the dest is an implied source
* (assumes the dest is the first source)
*/
- if (flags & ASYNC_TX_XOR_DROP_DST) {
+ if (submit->flags & ASYNC_TX_XOR_DROP_DST) {
src_cnt--;
src_list++;
}
/* wait for any prerequisite operations */
- async_tx_quiesce(&depend_tx);
+ async_tx_quiesce(&submit->depend_tx);
- do_sync_xor(dest, src_list, offset, src_cnt, len,
- flags, cb_fn, cb_param);
+ do_sync_xor(dest, src_list, offset, src_cnt, len, submit);
return NULL;
}
}
/**
- * async_xor_zero_sum - attempt a xor parity check with a dma engine.
+ * async_xor_val - attempt a xor parity check with a dma engine.
* @dest: destination page used if the xor is performed synchronously
- * @src_list: array of source pages. The dest page must be listed as a source
- * at index zero. The contents of this array may be overwritten.
+ * @src_list: array of source pages
* @offset: offset in pages to start transaction
* @src_cnt: number of source pages
* @len: length in bytes
* @result: 0 if sum == 0 else non-zero
- * @flags: ASYNC_TX_ACK, ASYNC_TX_DEP_ACK
- * @depend_tx: xor depends on the result of this transaction.
- * @cb_fn: function to call when the xor completes
- * @cb_param: parameter to pass to the callback routine
+ * @submit: submission / completion modifiers
+ *
+ * honored flags: ASYNC_TX_ACK
+ *
+ * src_list note: if the dest is also a source it must be at index zero.
+ * The contents of this array will be overwritten if a scribble region
+ * is not specified.
*/
struct dma_async_tx_descriptor *
-async_xor_zero_sum(struct page *dest, struct page **src_list,
- unsigned int offset, int src_cnt, size_t len,
- u32 *result, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_param)
+async_xor_val(struct page *dest, struct page **src_list, unsigned int offset,
+ int src_cnt, size_t len, enum sum_check_flags *result,
+ struct async_submit_ctl *submit)
{
- struct dma_chan *chan = async_tx_find_channel(depend_tx, DMA_ZERO_SUM,
+ struct dma_chan *chan = async_tx_find_channel(submit, DMA_XOR_VAL,
&dest, 1, src_list,
src_cnt, len);
struct dma_device *device = chan ? chan->device : NULL;
struct dma_async_tx_descriptor *tx = NULL;
+ dma_addr_t *dma_src = NULL;
BUG_ON(src_cnt <= 1);
- if (device && src_cnt <= device->max_xor) {
- dma_addr_t *dma_src = (dma_addr_t *) src_list;
- unsigned long dma_prep_flags = cb_fn ? DMA_PREP_INTERRUPT : 0;
+ if (submit->scribble)
+ dma_src = submit->scribble;
+ else if (sizeof(dma_addr_t) <= sizeof(struct page *))
+ dma_src = (dma_addr_t *) src_list;
+
+ if (dma_src && device && src_cnt <= device->max_xor &&
+ is_dma_xor_aligned(device, offset, 0, len)) {
+ unsigned long dma_prep_flags = 0;
int i;
pr_debug("%s: (async) len: %zu\n", __func__, len);
+ if (submit->cb_fn)
+ dma_prep_flags |= DMA_PREP_INTERRUPT;
+ if (submit->flags & ASYNC_TX_FENCE)
+ dma_prep_flags |= DMA_PREP_FENCE;
for (i = 0; i < src_cnt; i++)
dma_src[i] = dma_map_page(device->dev, src_list[i],
offset, len, DMA_TO_DEVICE);
- tx = device->device_prep_dma_zero_sum(chan, dma_src, src_cnt,
- len, result,
- dma_prep_flags);
+ tx = device->device_prep_dma_xor_val(chan, dma_src, src_cnt,
+ len, result,
+ dma_prep_flags);
if (unlikely(!tx)) {
- async_tx_quiesce(&depend_tx);
+ async_tx_quiesce(&submit->depend_tx);
while (!tx) {
dma_async_issue_pending(chan);
- tx = device->device_prep_dma_zero_sum(chan,
+ tx = device->device_prep_dma_xor_val(chan,
dma_src, src_cnt, len, result,
dma_prep_flags);
}
}
- async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
+ async_tx_submit(chan, tx, submit);
} else {
- unsigned long xor_flags = flags;
+ enum async_tx_flags flags_orig = submit->flags;
pr_debug("%s: (sync) len: %zu\n", __func__, len);
+ WARN_ONCE(device && src_cnt <= device->max_xor,
+ "%s: no space for dma address conversion\n",
+ __func__);
- xor_flags |= ASYNC_TX_XOR_DROP_DST;
- xor_flags &= ~ASYNC_TX_ACK;
+ submit->flags |= ASYNC_TX_XOR_DROP_DST;
+ submit->flags &= ~ASYNC_TX_ACK;
- tx = async_xor(dest, src_list, offset, src_cnt, len, xor_flags,
- depend_tx, NULL, NULL);
+ tx = async_xor(dest, src_list, offset, src_cnt, len, submit);
async_tx_quiesce(&tx);
- *result = page_is_zero(dest, offset, len) ? 0 : 1;
+ *result = !page_is_zero(dest, offset, len) << SUM_CHECK_P;
- async_tx_sync_epilog(cb_fn, cb_param);
+ async_tx_sync_epilog(submit);
+ submit->flags = flags_orig;
}
return tx;
}
-EXPORT_SYMBOL_GPL(async_xor_zero_sum);
-
-static int __init async_xor_init(void)
-{
- #ifdef CONFIG_ASYNC_TX_DMA
- /* To conserve stack space the input src_list (array of page pointers)
- * is reused to hold the array of dma addresses passed to the driver.
- * This conversion is only possible when dma_addr_t is less than the
- * the size of a pointer. HIGHMEM64G is known to violate this
- * assumption.
- */
- BUILD_BUG_ON(sizeof(dma_addr_t) > sizeof(struct page *));
- #endif
-
- return 0;
-}
-
-static void __exit async_xor_exit(void)
-{
- do { } while (0);
-}
-
-module_init(async_xor_init);
-module_exit(async_xor_exit);
+EXPORT_SYMBOL_GPL(async_xor_val);
MODULE_AUTHOR("Intel Corporation");
MODULE_DESCRIPTION("asynchronous xor/xor-zero-sum api");
--- /dev/null
+/*
+ * asynchronous raid6 recovery self test
+ * Copyright (c) 2009, Intel Corporation.
+ *
+ * based on drivers/md/raid6test/test.c:
+ * Copyright 2002-2007 H. Peter Anvin
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ */
+#include <linux/async_tx.h>
+#include <linux/random.h>
+
+#undef pr
+#define pr(fmt, args...) pr_info("raid6test: " fmt, ##args)
+
+#define NDISKS 16 /* Including P and Q */
+
+static struct page *dataptrs[NDISKS];
+static addr_conv_t addr_conv[NDISKS];
+static struct page *data[NDISKS+3];
+static struct page *spare;
+static struct page *recovi;
+static struct page *recovj;
+
+static void callback(void *param)
+{
+ struct completion *cmp = param;
+
+ complete(cmp);
+}
+
+static void makedata(int disks)
+{
+ int i, j;
+
+ for (i = 0; i < disks; i++) {
+ for (j = 0; j < PAGE_SIZE/sizeof(u32); j += sizeof(u32)) {
+ u32 *p = page_address(data[i]) + j;
+
+ *p = random32();
+ }
+
+ dataptrs[i] = data[i];
+ }
+}
+
+static char disk_type(int d, int disks)
+{
+ if (d == disks - 2)
+ return 'P';
+ else if (d == disks - 1)
+ return 'Q';
+ else
+ return 'D';
+}
+
+/* Recover two failed blocks. */
+static void raid6_dual_recov(int disks, size_t bytes, int faila, int failb, struct page **ptrs)
+{
+ struct async_submit_ctl submit;
+ struct completion cmp;
+ struct dma_async_tx_descriptor *tx = NULL;
+ enum sum_check_flags result = ~0;
+
+ if (faila > failb)
+ swap(faila, failb);
+
+ if (failb == disks-1) {
+ if (faila == disks-2) {
+ /* P+Q failure. Just rebuild the syndrome. */
+ init_async_submit(&submit, 0, NULL, NULL, NULL, addr_conv);
+ tx = async_gen_syndrome(ptrs, 0, disks, bytes, &submit);
+ } else {
+ struct page *blocks[disks];
+ struct page *dest;
+ int count = 0;
+ int i;
+
+ /* data+Q failure. Reconstruct data from P,
+ * then rebuild syndrome
+ */
+ for (i = disks; i-- ; ) {
+ if (i == faila || i == failb)
+ continue;
+ blocks[count++] = ptrs[i];
+ }
+ dest = ptrs[faila];
+ init_async_submit(&submit, ASYNC_TX_XOR_ZERO_DST, NULL,
+ NULL, NULL, addr_conv);
+ tx = async_xor(dest, blocks, 0, count, bytes, &submit);
+
+ init_async_submit(&submit, 0, tx, NULL, NULL, addr_conv);
+ tx = async_gen_syndrome(ptrs, 0, disks, bytes, &submit);
+ }
+ } else {
+ if (failb == disks-2) {
+ /* data+P failure. */
+ init_async_submit(&submit, 0, NULL, NULL, NULL, addr_conv);
+ tx = async_raid6_datap_recov(disks, bytes, faila, ptrs, &submit);
+ } else {
+ /* data+data failure. */
+ init_async_submit(&submit, 0, NULL, NULL, NULL, addr_conv);
+ tx = async_raid6_2data_recov(disks, bytes, faila, failb, ptrs, &submit);
+ }
+ }
+ init_completion(&cmp);
+ init_async_submit(&submit, ASYNC_TX_ACK, tx, callback, &cmp, addr_conv);
+ tx = async_syndrome_val(ptrs, 0, disks, bytes, &result, spare, &submit);
+ async_tx_issue_pending(tx);
+
+ if (wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000)) == 0)
+ pr("%s: timeout! (faila: %d failb: %d disks: %d)\n",
+ __func__, faila, failb, disks);
+
+ if (result != 0)
+ pr("%s: validation failure! faila: %d failb: %d sum_check_flags: %x\n",
+ __func__, faila, failb, result);
+}
+
+static int test_disks(int i, int j, int disks)
+{
+ int erra, errb;
+
+ memset(page_address(recovi), 0xf0, PAGE_SIZE);
+ memset(page_address(recovj), 0xba, PAGE_SIZE);
+
+ dataptrs[i] = recovi;
+ dataptrs[j] = recovj;
+
+ raid6_dual_recov(disks, PAGE_SIZE, i, j, dataptrs);
+
+ erra = memcmp(page_address(data[i]), page_address(recovi), PAGE_SIZE);
+ errb = memcmp(page_address(data[j]), page_address(recovj), PAGE_SIZE);
+
+ pr("%s(%d, %d): faila=%3d(%c) failb=%3d(%c) %s\n",
+ __func__, i, j, i, disk_type(i, disks), j, disk_type(j, disks),
+ (!erra && !errb) ? "OK" : !erra ? "ERRB" : !errb ? "ERRA" : "ERRAB");
+
+ dataptrs[i] = data[i];
+ dataptrs[j] = data[j];
+
+ return erra || errb;
+}
+
+static int test(int disks, int *tests)
+{
+ struct dma_async_tx_descriptor *tx;
+ struct async_submit_ctl submit;
+ struct completion cmp;
+ int err = 0;
+ int i, j;
+
+ recovi = data[disks];
+ recovj = data[disks+1];
+ spare = data[disks+2];
+
+ makedata(disks);
+
+ /* Nuke syndromes */
+ memset(page_address(data[disks-2]), 0xee, PAGE_SIZE);
+ memset(page_address(data[disks-1]), 0xee, PAGE_SIZE);
+
+ /* Generate assumed good syndrome */
+ init_completion(&cmp);
+ init_async_submit(&submit, ASYNC_TX_ACK, NULL, callback, &cmp, addr_conv);
+ tx = async_gen_syndrome(dataptrs, 0, disks, PAGE_SIZE, &submit);
+ async_tx_issue_pending(tx);
+
+ if (wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000)) == 0) {
+ pr("error: initial gen_syndrome(%d) timed out\n", disks);
+ return 1;
+ }
+
+ pr("testing the %d-disk case...\n", disks);
+ for (i = 0; i < disks-1; i++)
+ for (j = i+1; j < disks; j++) {
+ (*tests)++;
+ err += test_disks(i, j, disks);
+ }
+
+ return err;
+}
+
+
+static int raid6_test(void)
+{
+ int err = 0;
+ int tests = 0;
+ int i;
+
+ for (i = 0; i < NDISKS+3; i++) {
+ data[i] = alloc_page(GFP_KERNEL);
+ if (!data[i]) {
+ while (i--)
+ put_page(data[i]);
+ return -ENOMEM;
+ }
+ }
+
+ /* the 4-disk and 5-disk cases are special for the recovery code */
+ if (NDISKS > 4)
+ err += test(4, &tests);
+ if (NDISKS > 5)
+ err += test(5, &tests);
+ err += test(NDISKS, &tests);
+
+ pr("\n");
+ pr("complete (%d tests, %d failure%s)\n",
+ tests, err, err == 1 ? "" : "s");
+
+ for (i = 0; i < NDISKS+3; i++)
+ put_page(data[i]);
+
+ return 0;
+}
+
+static void raid6_test_exit(void)
+{
+}
+
+/* when compiled-in wait for drivers to load first (assumes dma drivers
+ * are also compliled-in)
+ */
+late_initcall(raid6_test);
+module_exit(raid6_test_exit);
+MODULE_AUTHOR("Dan Williams <dan.j.williams@intel.com>");
+MODULE_DESCRIPTION("asynchronous RAID-6 recovery self tests");
+MODULE_LICENSE("GPL");
select ACPI_CONTAINER
default y
+config ACPI_PROCESSOR_AGGREGATOR
+ tristate "Processor Aggregator"
+ depends on ACPI_PROCESSOR
+ depends on EXPERIMENTAL
+ depends on X86
+ help
+ ACPI 4.0 defines processor Aggregator, which enables OS to perform
+ specfic processor configuration and control that applies to all
+ processors in the platform. Currently only logical processor idling
+ is defined, which is to reduce power consumption. This driver
+ support the new device.
+
config ACPI_THERMAL
tristate "Thermal Zone"
depends on ACPI_PROCESSOR
processor-y := processor_core.o processor_throttling.o
processor-y += processor_idle.o processor_thermal.o
processor-$(CONFIG_CPU_FREQ) += processor_perflib.o
+
+obj-$(CONFIG_ACPI_PROCESSOR_AGGREGATOR) += acpi_pad.o
--- /dev/null
+/*
+ * acpi_pad.c ACPI Processor Aggregator Driver
+ *
+ * Copyright (c) 2009, Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/cpumask.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/cpu.h>
+#include <linux/clockchips.h>
+#include <acpi/acpi_bus.h>
+#include <acpi/acpi_drivers.h>
+
+#define ACPI_PROCESSOR_AGGREGATOR_CLASS "processor_aggregator"
+#define ACPI_PROCESSOR_AGGREGATOR_DEVICE_NAME "Processor Aggregator"
+#define ACPI_PROCESSOR_AGGREGATOR_NOTIFY 0x80
+static DEFINE_MUTEX(isolated_cpus_lock);
+
+#define MWAIT_SUBSTATE_MASK (0xf)
+#define MWAIT_CSTATE_MASK (0xf)
+#define MWAIT_SUBSTATE_SIZE (4)
+#define CPUID_MWAIT_LEAF (5)
+#define CPUID5_ECX_EXTENSIONS_SUPPORTED (0x1)
+#define CPUID5_ECX_INTERRUPT_BREAK (0x2)
+static unsigned long power_saving_mwait_eax;
+static void power_saving_mwait_init(void)
+{
+ unsigned int eax, ebx, ecx, edx;
+ unsigned int highest_cstate = 0;
+ unsigned int highest_subcstate = 0;
+ int i;
+
+ if (!boot_cpu_has(X86_FEATURE_MWAIT))
+ return;
+ if (boot_cpu_data.cpuid_level < CPUID_MWAIT_LEAF)
+ return;
+
+ cpuid(CPUID_MWAIT_LEAF, &eax, &ebx, &ecx, &edx);
+
+ if (!(ecx & CPUID5_ECX_EXTENSIONS_SUPPORTED) ||
+ !(ecx & CPUID5_ECX_INTERRUPT_BREAK))
+ return;
+
+ edx >>= MWAIT_SUBSTATE_SIZE;
+ for (i = 0; i < 7 && edx; i++, edx >>= MWAIT_SUBSTATE_SIZE) {
+ if (edx & MWAIT_SUBSTATE_MASK) {
+ highest_cstate = i;
+ highest_subcstate = edx & MWAIT_SUBSTATE_MASK;
+ }
+ }
+ power_saving_mwait_eax = (highest_cstate << MWAIT_SUBSTATE_SIZE) |
+ (highest_subcstate - 1);
+
+ for_each_online_cpu(i)
+ clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ON, &i);
+
+#if defined(CONFIG_GENERIC_TIME) && defined(CONFIG_X86)
+ switch (boot_cpu_data.x86_vendor) {
+ case X86_VENDOR_AMD:
+ case X86_VENDOR_INTEL:
+ /*
+ * AMD Fam10h TSC will tick in all
+ * C/P/S0/S1 states when this bit is set.
+ */
+ if (boot_cpu_has(X86_FEATURE_NONSTOP_TSC))
+ return;
+
+ /*FALL THROUGH*/
+ default:
+ /* TSC could halt in idle, so notify users */
+ mark_tsc_unstable("TSC halts in idle");
+ }
+#endif
+}
+
+static unsigned long cpu_weight[NR_CPUS];
+static int tsk_in_cpu[NR_CPUS] = {[0 ... NR_CPUS-1] = -1};
+static DECLARE_BITMAP(pad_busy_cpus_bits, NR_CPUS);
+static void round_robin_cpu(unsigned int tsk_index)
+{
+ struct cpumask *pad_busy_cpus = to_cpumask(pad_busy_cpus_bits);
+ cpumask_var_t tmp;
+ int cpu;
+ unsigned long min_weight = -1, preferred_cpu;
+
+ if (!alloc_cpumask_var(&tmp, GFP_KERNEL))
+ return;
+
+ mutex_lock(&isolated_cpus_lock);
+ cpumask_clear(tmp);
+ for_each_cpu(cpu, pad_busy_cpus)
+ cpumask_or(tmp, tmp, topology_thread_cpumask(cpu));
+ cpumask_andnot(tmp, cpu_online_mask, tmp);
+ /* avoid HT sibilings if possible */
+ if (cpumask_empty(tmp))
+ cpumask_andnot(tmp, cpu_online_mask, pad_busy_cpus);
+ if (cpumask_empty(tmp)) {
+ mutex_unlock(&isolated_cpus_lock);
+ return;
+ }
+ for_each_cpu(cpu, tmp) {
+ if (cpu_weight[cpu] < min_weight) {
+ min_weight = cpu_weight[cpu];
+ preferred_cpu = cpu;
+ }
+ }
+
+ if (tsk_in_cpu[tsk_index] != -1)
+ cpumask_clear_cpu(tsk_in_cpu[tsk_index], pad_busy_cpus);
+ tsk_in_cpu[tsk_index] = preferred_cpu;
+ cpumask_set_cpu(preferred_cpu, pad_busy_cpus);
+ cpu_weight[preferred_cpu]++;
+ mutex_unlock(&isolated_cpus_lock);
+
+ set_cpus_allowed_ptr(current, cpumask_of(preferred_cpu));
+}
+
+static void exit_round_robin(unsigned int tsk_index)
+{
+ struct cpumask *pad_busy_cpus = to_cpumask(pad_busy_cpus_bits);
+ cpumask_clear_cpu(tsk_in_cpu[tsk_index], pad_busy_cpus);
+ tsk_in_cpu[tsk_index] = -1;
+}
+
+static unsigned int idle_pct = 5; /* percentage */
+static unsigned int round_robin_time = 10; /* second */
+static int power_saving_thread(void *data)
+{
+ struct sched_param param = {.sched_priority = 1};
+ int do_sleep;
+ unsigned int tsk_index = (unsigned long)data;
+ u64 last_jiffies = 0;
+
+ sched_setscheduler(current, SCHED_RR, ¶m);
+
+ while (!kthread_should_stop()) {
+ int cpu;
+ u64 expire_time;
+
+ try_to_freeze();
+
+ /* round robin to cpus */
+ if (last_jiffies + round_robin_time * HZ < jiffies) {
+ last_jiffies = jiffies;
+ round_robin_cpu(tsk_index);
+ }
+
+ do_sleep = 0;
+
+ current_thread_info()->status &= ~TS_POLLING;
+ /*
+ * TS_POLLING-cleared state must be visible before we test
+ * NEED_RESCHED:
+ */
+ smp_mb();
+
+ expire_time = jiffies + HZ * (100 - idle_pct) / 100;
+
+ while (!need_resched()) {
+ local_irq_disable();
+ cpu = smp_processor_id();
+ clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER,
+ &cpu);
+ stop_critical_timings();
+
+ __monitor((void *)¤t_thread_info()->flags, 0, 0);
+ smp_mb();
+ if (!need_resched())
+ __mwait(power_saving_mwait_eax, 1);
+
+ start_critical_timings();
+ clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT,
+ &cpu);
+ local_irq_enable();
+
+ if (jiffies > expire_time) {
+ do_sleep = 1;
+ break;
+ }
+ }
+
+ current_thread_info()->status |= TS_POLLING;
+
+ /*
+ * current sched_rt has threshold for rt task running time.
+ * When a rt task uses 95% CPU time, the rt thread will be
+ * scheduled out for 5% CPU time to not starve other tasks. But
+ * the mechanism only works when all CPUs have RT task running,
+ * as if one CPU hasn't RT task, RT task from other CPUs will
+ * borrow CPU time from this CPU and cause RT task use > 95%
+ * CPU time. To make 'avoid staration' work, takes a nap here.
+ */
+ if (do_sleep)
+ schedule_timeout_killable(HZ * idle_pct / 100);
+ }
+
+ exit_round_robin(tsk_index);
+ return 0;
+}
+
+static struct task_struct *ps_tsks[NR_CPUS];
+static unsigned int ps_tsk_num;
+static int create_power_saving_task(void)
+{
+ ps_tsks[ps_tsk_num] = kthread_run(power_saving_thread,
+ (void *)(unsigned long)ps_tsk_num,
+ "power_saving/%d", ps_tsk_num);
+ if (ps_tsks[ps_tsk_num]) {
+ ps_tsk_num++;
+ return 0;
+ }
+ return -EINVAL;
+}
+
+static void destroy_power_saving_task(void)
+{
+ if (ps_tsk_num > 0) {
+ ps_tsk_num--;
+ kthread_stop(ps_tsks[ps_tsk_num]);
+ }
+}
+
+static void set_power_saving_task_num(unsigned int num)
+{
+ if (num > ps_tsk_num) {
+ while (ps_tsk_num < num) {
+ if (create_power_saving_task())
+ return;
+ }
+ } else if (num < ps_tsk_num) {
+ while (ps_tsk_num > num)
+ destroy_power_saving_task();
+ }
+}
+
+static int acpi_pad_idle_cpus(unsigned int num_cpus)
+{
+ get_online_cpus();
+
+ num_cpus = min_t(unsigned int, num_cpus, num_online_cpus());
+ set_power_saving_task_num(num_cpus);
+
+ put_online_cpus();
+ return 0;
+}
+
+static uint32_t acpi_pad_idle_cpus_num(void)
+{
+ return ps_tsk_num;
+}
+
+static ssize_t acpi_pad_rrtime_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ unsigned long num;
+ if (strict_strtoul(buf, 0, &num))
+ return -EINVAL;
+ if (num < 1 || num >= 100)
+ return -EINVAL;
+ mutex_lock(&isolated_cpus_lock);
+ round_robin_time = num;
+ mutex_unlock(&isolated_cpus_lock);
+ return count;
+}
+
+static ssize_t acpi_pad_rrtime_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return scnprintf(buf, PAGE_SIZE, "%d", round_robin_time);
+}
+static DEVICE_ATTR(rrtime, S_IRUGO|S_IWUSR,
+ acpi_pad_rrtime_show,
+ acpi_pad_rrtime_store);
+
+static ssize_t acpi_pad_idlepct_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ unsigned long num;
+ if (strict_strtoul(buf, 0, &num))
+ return -EINVAL;
+ if (num < 1 || num >= 100)
+ return -EINVAL;
+ mutex_lock(&isolated_cpus_lock);
+ idle_pct = num;
+ mutex_unlock(&isolated_cpus_lock);
+ return count;
+}
+
+static ssize_t acpi_pad_idlepct_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return scnprintf(buf, PAGE_SIZE, "%d", idle_pct);
+}
+static DEVICE_ATTR(idlepct, S_IRUGO|S_IWUSR,
+ acpi_pad_idlepct_show,
+ acpi_pad_idlepct_store);
+
+static ssize_t acpi_pad_idlecpus_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ unsigned long num;
+ if (strict_strtoul(buf, 0, &num))
+ return -EINVAL;
+ mutex_lock(&isolated_cpus_lock);
+ acpi_pad_idle_cpus(num);
+ mutex_unlock(&isolated_cpus_lock);
+ return count;
+}
+
+static ssize_t acpi_pad_idlecpus_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return cpumask_scnprintf(buf, PAGE_SIZE,
+ to_cpumask(pad_busy_cpus_bits));
+}
+static DEVICE_ATTR(idlecpus, S_IRUGO|S_IWUSR,
+ acpi_pad_idlecpus_show,
+ acpi_pad_idlecpus_store);
+
+static int acpi_pad_add_sysfs(struct acpi_device *device)
+{
+ int result;
+
+ result = device_create_file(&device->dev, &dev_attr_idlecpus);
+ if (result)
+ return -ENODEV;
+ result = device_create_file(&device->dev, &dev_attr_idlepct);
+ if (result) {
+ device_remove_file(&device->dev, &dev_attr_idlecpus);
+ return -ENODEV;
+ }
+ result = device_create_file(&device->dev, &dev_attr_rrtime);
+ if (result) {
+ device_remove_file(&device->dev, &dev_attr_idlecpus);
+ device_remove_file(&device->dev, &dev_attr_idlepct);
+ return -ENODEV;
+ }
+ return 0;
+}
+
+static void acpi_pad_remove_sysfs(struct acpi_device *device)
+{
+ device_remove_file(&device->dev, &dev_attr_idlecpus);
+ device_remove_file(&device->dev, &dev_attr_idlepct);
+ device_remove_file(&device->dev, &dev_attr_rrtime);
+}
+
+/* Query firmware how many CPUs should be idle */
+static int acpi_pad_pur(acpi_handle handle, int *num_cpus)
+{
+ struct acpi_buffer buffer = {ACPI_ALLOCATE_BUFFER, NULL};
+ acpi_status status;
+ union acpi_object *package;
+ int rev, num, ret = -EINVAL;
+
+ status = acpi_evaluate_object(handle, "_PUR", NULL, &buffer);
+ if (ACPI_FAILURE(status))
+ return -EINVAL;
+ package = buffer.pointer;
+ if (package->type != ACPI_TYPE_PACKAGE || package->package.count != 2)
+ goto out;
+ rev = package->package.elements[0].integer.value;
+ num = package->package.elements[1].integer.value;
+ if (rev != 1)
+ goto out;
+ *num_cpus = num;
+ ret = 0;
+out:
+ kfree(buffer.pointer);
+ return ret;
+}
+
+/* Notify firmware how many CPUs are idle */
+static void acpi_pad_ost(acpi_handle handle, int stat,
+ uint32_t idle_cpus)
+{
+ union acpi_object params[3] = {
+ {.type = ACPI_TYPE_INTEGER,},
+ {.type = ACPI_TYPE_INTEGER,},
+ {.type = ACPI_TYPE_BUFFER,},
+ };
+ struct acpi_object_list arg_list = {3, params};
+
+ params[0].integer.value = ACPI_PROCESSOR_AGGREGATOR_NOTIFY;
+ params[1].integer.value = stat;
+ params[2].buffer.length = 4;
+ params[2].buffer.pointer = (void *)&idle_cpus;
+ acpi_evaluate_object(handle, "_OST", &arg_list, NULL);
+}
+
+static void acpi_pad_handle_notify(acpi_handle handle)
+{
+ int num_cpus, ret;
+ uint32_t idle_cpus;
+
+ mutex_lock(&isolated_cpus_lock);
+ if (acpi_pad_pur(handle, &num_cpus)) {
+ mutex_unlock(&isolated_cpus_lock);
+ return;
+ }
+ ret = acpi_pad_idle_cpus(num_cpus);
+ idle_cpus = acpi_pad_idle_cpus_num();
+ if (!ret)
+ acpi_pad_ost(handle, 0, idle_cpus);
+ else
+ acpi_pad_ost(handle, 1, 0);
+ mutex_unlock(&isolated_cpus_lock);
+}
+
+static void acpi_pad_notify(acpi_handle handle, u32 event,
+ void *data)
+{
+ struct acpi_device *device = data;
+
+ switch (event) {
+ case ACPI_PROCESSOR_AGGREGATOR_NOTIFY:
+ acpi_pad_handle_notify(handle);
+ acpi_bus_generate_proc_event(device, event, 0);
+ acpi_bus_generate_netlink_event(device->pnp.device_class,
+ dev_name(&device->dev), event, 0);
+ break;
+ default:
+ printk(KERN_WARNING"Unsupported event [0x%x]\n", event);
+ break;
+ }
+}
+
+static int acpi_pad_add(struct acpi_device *device)
+{
+ acpi_status status;
+
+ strcpy(acpi_device_name(device), ACPI_PROCESSOR_AGGREGATOR_DEVICE_NAME);
+ strcpy(acpi_device_class(device), ACPI_PROCESSOR_AGGREGATOR_CLASS);
+
+ if (acpi_pad_add_sysfs(device))
+ return -ENODEV;
+
+ status = acpi_install_notify_handler(device->handle,
+ ACPI_DEVICE_NOTIFY, acpi_pad_notify, device);
+ if (ACPI_FAILURE(status)) {
+ acpi_pad_remove_sysfs(device);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int acpi_pad_remove(struct acpi_device *device,
+ int type)
+{
+ mutex_lock(&isolated_cpus_lock);
+ acpi_pad_idle_cpus(0);
+ mutex_unlock(&isolated_cpus_lock);
+
+ acpi_remove_notify_handler(device->handle,
+ ACPI_DEVICE_NOTIFY, acpi_pad_notify);
+ acpi_pad_remove_sysfs(device);
+ return 0;
+}
+
+static const struct acpi_device_id pad_device_ids[] = {
+ {"ACPI000C", 0},
+ {"", 0},
+};
+MODULE_DEVICE_TABLE(acpi, pad_device_ids);
+
+static struct acpi_driver acpi_pad_driver = {
+ .name = "processor_aggregator",
+ .class = ACPI_PROCESSOR_AGGREGATOR_CLASS,
+ .ids = pad_device_ids,
+ .ops = {
+ .add = acpi_pad_add,
+ .remove = acpi_pad_remove,
+ },
+};
+
+static int __init acpi_pad_init(void)
+{
+ power_saving_mwait_init();
+ if (power_saving_mwait_eax == 0)
+ return -EINVAL;
+
+ return acpi_bus_register_driver(&acpi_pad_driver);
+}
+
+static void __exit acpi_pad_exit(void)
+{
+ acpi_bus_unregister_driver(&acpi_pad_driver);
+}
+
+module_init(acpi_pad_init);
+module_exit(acpi_pad_exit);
+MODULE_AUTHOR("Shaohua Li<shaohua.li@intel.com>");
+MODULE_DESCRIPTION("ACPI Processor Aggregator Driver");
+MODULE_LICENSE("GPL");
EXPORT_SYMBOL(acpi_bus_get_device);
-int acpi_bus_get_status(struct acpi_device *device)
+acpi_status acpi_bus_get_status_handle(acpi_handle handle,
+ unsigned long long *sta)
{
- acpi_status status = AE_OK;
- unsigned long long sta = 0;
-
+ acpi_status status;
- if (!device)
- return -EINVAL;
+ status = acpi_evaluate_integer(handle, "_STA", NULL, sta);
+ if (ACPI_SUCCESS(status))
+ return AE_OK;
- /*
- * Evaluate _STA if present.
- */
- if (device->flags.dynamic_status) {
- status =
- acpi_evaluate_integer(device->handle, "_STA", NULL, &sta);
- if (ACPI_FAILURE(status))
- return -ENODEV;
- STRUCT_TO_INT(device->status) = (int)sta;
+ if (status == AE_NOT_FOUND) {
+ *sta = ACPI_STA_DEVICE_PRESENT | ACPI_STA_DEVICE_ENABLED |
+ ACPI_STA_DEVICE_UI | ACPI_STA_DEVICE_FUNCTIONING;
+ return AE_OK;
}
+ return status;
+}
- /*
- * According to ACPI spec some device can be present and functional
- * even if the parent is not present but functional.
- * In such conditions the child device should not inherit the status
- * from the parent.
- */
- else
- STRUCT_TO_INT(device->status) =
- ACPI_STA_DEVICE_PRESENT | ACPI_STA_DEVICE_ENABLED |
- ACPI_STA_DEVICE_UI | ACPI_STA_DEVICE_FUNCTIONING;
+int acpi_bus_get_status(struct acpi_device *device)
+{
+ acpi_status status;
+ unsigned long long sta;
+
+ status = acpi_bus_get_status_handle(device->handle, &sta);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
+
+ STRUCT_TO_INT(device->status) = (int) sta;
if (device->status.functional && !device->status.present) {
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device [%s] status [%08x]: "
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device [%s] status [%08x]\n",
device->pnp.bus_id,
(u32) STRUCT_TO_INT(device->status)));
-
return 0;
}
-
EXPORT_SYMBOL(acpi_bus_get_status);
void acpi_bus_private_data_handler(acpi_handle handle,
.release = single_release,
};
+static BLOCKING_NOTIFIER_HEAD(acpi_lid_notifier);
+static struct acpi_device *lid_device;
+
/* --------------------------------------------------------------------------
FS Interface (/proc)
-------------------------------------------------------------------------- */
/* --------------------------------------------------------------------------
Driver Interface
-------------------------------------------------------------------------- */
+int acpi_lid_notifier_register(struct notifier_block *nb)
+{
+ return blocking_notifier_chain_register(&acpi_lid_notifier, nb);
+}
+EXPORT_SYMBOL(acpi_lid_notifier_register);
+
+int acpi_lid_notifier_unregister(struct notifier_block *nb)
+{
+ return blocking_notifier_chain_unregister(&acpi_lid_notifier, nb);
+}
+EXPORT_SYMBOL(acpi_lid_notifier_unregister);
+
+int acpi_lid_open(void)
+{
+ acpi_status status;
+ unsigned long long state;
+
+ status = acpi_evaluate_integer(lid_device->handle, "_LID", NULL,
+ &state);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
+
+ return !!state;
+}
+EXPORT_SYMBOL(acpi_lid_open);
+
static int acpi_lid_send_state(struct acpi_device *device)
{
struct acpi_button *button = acpi_driver_data(device);
unsigned long long state;
acpi_status status;
+ int ret;
status = acpi_evaluate_integer(device->handle, "_LID", NULL, &state);
if (ACPI_FAILURE(status))
/* input layer checks if event is redundant */
input_report_switch(button->input, SW_LID, !state);
input_sync(button->input);
- return 0;
+
+ ret = blocking_notifier_call_chain(&acpi_lid_notifier, state, device);
+ if (ret == NOTIFY_DONE)
+ ret = blocking_notifier_call_chain(&acpi_lid_notifier, state,
+ device);
+ return ret;
}
static void acpi_button_notify(struct acpi_device *device, u32 event)
error = input_register_device(input);
if (error)
goto err_remove_fs;
- if (button->type == ACPI_BUTTON_TYPE_LID)
+ if (button->type == ACPI_BUTTON_TYPE_LID) {
acpi_lid_send_state(device);
+ /*
+ * This assumes there's only one lid device, or if there are
+ * more we only care about the last one...
+ */
+ lid_device = device;
+ }
if (device->wakeup.flags.valid) {
/* Button's GPE is run-wake GPE */
struct list_head dependent_devices;
struct list_head hotplug_devices;
- struct list_head sibiling;
+ struct list_head sibling;
struct platform_device *dock_device;
};
static LIST_HEAD(dock_stations);
if (is_dock(handle))
return 1;
- list_for_each_entry(dock_station, &dock_stations, sibiling) {
+ list_for_each_entry(dock_station, &dock_stations, sibling) {
if (find_dock_dependent_device(dock_station, handle))
return 1;
}
* make sure this handle is for a device dependent on the dock,
* this would include the dock station itself
*/
- list_for_each_entry(dock_station, &dock_stations, sibiling) {
+ list_for_each_entry(dock_station, &dock_stations, sibling) {
/*
* An ATA bay can be in a dock and itself can be ejected
* seperately, so there are two 'dock stations' which need the
if (!dock_station_count)
return;
- list_for_each_entry(dock_station, &dock_stations, sibiling) {
+ list_for_each_entry(dock_station, &dock_stations, sibling) {
dd = find_dock_dependent_device(dock_station, handle);
if (dd)
dock_del_hotplug_device(dock_station, dd);
if (event != ACPI_NOTIFY_BUS_CHECK && event != ACPI_NOTIFY_DEVICE_CHECK
&& event != ACPI_NOTIFY_EJECT_REQUEST)
return 0;
- list_for_each_entry(dock_station, &dock_stations, sibiling) {
+ list_for_each_entry(dock_station, &dock_stations, sibling) {
if (dock_station->handle == handle) {
struct dock_data *dock_data;
dock_station->last_dock_time = jiffies - HZ;
INIT_LIST_HEAD(&dock_station->dependent_devices);
INIT_LIST_HEAD(&dock_station->hotplug_devices);
- INIT_LIST_HEAD(&dock_station->sibiling);
+ INIT_LIST_HEAD(&dock_station->sibling);
spin_lock_init(&dock_station->dd_lock);
mutex_init(&dock_station->hp_lock);
ATOMIC_INIT_NOTIFIER_HEAD(&dock_notifier_list);
add_dock_dependent_device(dock_station, dd);
dock_station_count++;
- list_add(&dock_station->sibiling, &dock_stations);
+ list_add(&dock_station->sibling, &dock_stations);
return 0;
dock_add_err_unregister:
struct dock_station *tmp;
unregister_acpi_bus_notifier(&dock_acpi_notifier);
- list_for_each_entry_safe(dock_station, tmp, &dock_stations, sibiling)
+ list_for_each_entry_safe(dock_station, tmp, &dock_stations, sibling)
dock_remove(dock_station);
}
} *boot_ec, *first_ec;
static int EC_FLAGS_MSI; /* Out-of-spec MSI controller */
+static int EC_FLAGS_VALIDATE_ECDT; /* ASUStec ECDTs need to be validated */
+static int EC_FLAGS_SKIP_DSDT_SCAN; /* Not all BIOS survive early DSDT scan */
/* --------------------------------------------------------------------------
Transaction Management
}
advance_transaction(ec, acpi_ec_read_status(ec));
} while (time_before(jiffies, delay));
- if (!ec->curr->irq_count ||
- (acpi_ec_read_status(ec) & ACPI_EC_FLAG_IBF))
+ if (acpi_ec_read_status(ec) & ACPI_EC_FLAG_IBF)
break;
- /* try restart command if we get any false interrupts */
pr_debug(PREFIX "controller reset, restart transaction\n");
spin_lock_irqsave(&ec->curr_lock, flags);
start_transaction(ec);
{"", 0},
};
+/* Some BIOS do not survive early DSDT scan, skip it */
+static int ec_skip_dsdt_scan(const struct dmi_system_id *id)
+{
+ EC_FLAGS_SKIP_DSDT_SCAN = 1;
+ return 0;
+}
+
+/* ASUStek often supplies us with broken ECDT, validate it */
+static int ec_validate_ecdt(const struct dmi_system_id *id)
+{
+ EC_FLAGS_VALIDATE_ECDT = 1;
+ return 0;
+}
+
+/* MSI EC needs special treatment, enable it */
+static int ec_flag_msi(const struct dmi_system_id *id)
+{
+ EC_FLAGS_MSI = 1;
+ EC_FLAGS_VALIDATE_ECDT = 1;
+ return 0;
+}
+
+static struct dmi_system_id __initdata ec_dmi_table[] = {
+ {
+ ec_skip_dsdt_scan, "Compal JFL92", {
+ DMI_MATCH(DMI_BIOS_VENDOR, "COMPAL"),
+ DMI_MATCH(DMI_BOARD_NAME, "JFL92") }, NULL},
+ {
+ ec_flag_msi, "MSI hardware", {
+ DMI_MATCH(DMI_BIOS_VENDOR, "Micro-Star"),
+ DMI_MATCH(DMI_CHASSIS_VENDOR, "MICRO-Star") }, NULL},
+ {
+ ec_validate_ecdt, "ASUS hardware", {
+ DMI_MATCH(DMI_BIOS_VENDOR, "ASUS") }, NULL},
+ {},
+};
+
+
int __init acpi_ec_ecdt_probe(void)
{
acpi_status status;
/*
* Generate a boot ec context
*/
- if (dmi_name_in_vendors("Micro-Star") ||
- dmi_name_in_vendors("Notebook")) {
- pr_info(PREFIX "Enabling special treatment for EC from MSI.\n");
- EC_FLAGS_MSI = 1;
- }
+ dmi_check_system(ec_dmi_table);
status = acpi_get_table(ACPI_SIG_ECDT, 1,
(struct acpi_table_header **)&ecdt_ptr);
if (ACPI_SUCCESS(status)) {
boot_ec->handle = ACPI_ROOT_OBJECT;
acpi_get_handle(ACPI_ROOT_OBJECT, ecdt_ptr->id, &boot_ec->handle);
/* Don't trust ECDT, which comes from ASUSTek */
- if (!dmi_name_in_vendors("ASUS") && EC_FLAGS_MSI == 0)
+ if (!EC_FLAGS_VALIDATE_ECDT)
goto install;
saved_ec = kmalloc(sizeof(struct acpi_ec), GFP_KERNEL);
if (!saved_ec)
memcpy(saved_ec, boot_ec, sizeof(struct acpi_ec));
/* fall through */
}
+
+ if (EC_FLAGS_SKIP_DSDT_SCAN)
+ return -ENODEV;
+
/* This workaround is needed only on some broken machines,
* which require early EC, but fail to provide ECDT */
printk(KERN_DEBUG PREFIX "Look up EC in DSDT\n");
res_list_elem->name,
(long long) res_list_elem->start,
(long long) res_list_elem->end);
- printk(KERN_INFO "ACPI: Device needs an ACPI driver\n");
+ if (acpi_enforce_resources == ENFORCE_RESOURCES_LAX)
+ printk(KERN_NOTICE "ACPI: This conflict may"
+ " cause random problems and system"
+ " instability\n");
+ printk(KERN_INFO "ACPI: If an ACPI driver is available"
+ " for this device, you should use it instead of"
+ " the native driver\n");
}
if (acpi_enforce_resources == ENFORCE_RESOURCES_STRICT)
return -EBUSY;
if (len > 4)
len = 4;
+ if (len < 0)
+ return -EFAULT;
if (copy_from_user(strbuf, buffer, len))
return -EFAULT;
goto err_remove_sysfs;
}
- if (pr->flags.throttling) {
- printk(KERN_INFO PREFIX "%s [%s] (supports",
- acpi_device_name(device), acpi_device_bid(device));
- printk(" %d throttling states", pr->throttling.state_count);
- printk(")\n");
- }
-
return 0;
err_remove_sysfs:
#ifdef CONFIG_ACPI_PROCFS
struct proc_dir_entry *entry = NULL;
#endif
- unsigned int i;
if (boot_option_idle_override)
return 0;
acpi_processor_setup_cpuidle(pr);
if (cpuidle_register_device(&pr->power.dev))
return -EIO;
-
- printk(KERN_INFO PREFIX "CPU%d (power states:", pr->id);
- for (i = 1; i <= pr->power.count; i++)
- if (pr->power.states[i].valid)
- printk(" C%d[C%d]", i,
- pr->power.states[i].type);
- printk(")\n");
}
#ifdef CONFIG_ACPI_PROCFS
/* 'power' [R] */
#define ACPI_BUS_HID "LNXSYBUS"
#define ACPI_BUS_DEVICE_NAME "System Bus"
+#define ACPI_IS_ROOT_DEVICE(device) (!(device)->parent)
+
static LIST_HEAD(acpi_device_list);
static LIST_HEAD(acpi_bus_id_list);
DEFINE_MUTEX(acpi_device_lock);
{
int len;
int count;
-
- if (!acpi_dev->flags.hardware_id && !acpi_dev->flags.compatible_ids)
- return -ENODEV;
+ struct acpi_hardware_id *id;
len = snprintf(modalias, size, "acpi:");
size -= len;
- if (acpi_dev->flags.hardware_id) {
- count = snprintf(&modalias[len], size, "%s:",
- acpi_dev->pnp.hardware_id);
+ list_for_each_entry(id, &acpi_dev->pnp.ids, list) {
+ count = snprintf(&modalias[len], size, "%s:", id->id);
if (count < 0 || count >= size)
return -EINVAL;
len += count;
size -= count;
}
- if (acpi_dev->flags.compatible_ids) {
- struct acpica_device_id_list *cid_list;
- int i;
-
- cid_list = acpi_dev->pnp.cid_list;
- for (i = 0; i < cid_list->count; i++) {
- count = snprintf(&modalias[len], size, "%s:",
- cid_list->ids[i].string);
- if (count < 0 || count >= size) {
- printk(KERN_ERR PREFIX "%s cid[%i] exceeds event buffer size",
- acpi_dev->pnp.device_name, i);
- break;
- }
- len += count;
- size -= count;
- }
- }
-
modalias[len] = '\0';
return len;
}
acpi_device_hid_show(struct device *dev, struct device_attribute *attr, char *buf) {
struct acpi_device *acpi_dev = to_acpi_device(dev);
- return sprintf(buf, "%s\n", acpi_dev->pnp.hardware_id);
+ return sprintf(buf, "%s\n", acpi_device_hid(acpi_dev));
}
static DEVICE_ATTR(hid, 0444, acpi_device_hid_show, NULL);
goto end;
}
- if (dev->flags.hardware_id) {
- result = device_create_file(&dev->dev, &dev_attr_hid);
- if (result)
- goto end;
- }
+ result = device_create_file(&dev->dev, &dev_attr_hid);
+ if (result)
+ goto end;
- if (dev->flags.hardware_id || dev->flags.compatible_ids) {
- result = device_create_file(&dev->dev, &dev_attr_modalias);
- if (result)
- goto end;
- }
+ result = device_create_file(&dev->dev, &dev_attr_modalias);
+ if (result)
+ goto end;
/*
* If device has _EJ0, 'eject' file is created that is used to trigger
if (ACPI_SUCCESS(status))
device_remove_file(&dev->dev, &dev_attr_eject);
- if (dev->flags.hardware_id || dev->flags.compatible_ids)
- device_remove_file(&dev->dev, &dev_attr_modalias);
-
- if (dev->flags.hardware_id)
- device_remove_file(&dev->dev, &dev_attr_hid);
+ device_remove_file(&dev->dev, &dev_attr_modalias);
+ device_remove_file(&dev->dev, &dev_attr_hid);
if (dev->handle)
device_remove_file(&dev->dev, &dev_attr_path);
}
const struct acpi_device_id *ids)
{
const struct acpi_device_id *id;
+ struct acpi_hardware_id *hwid;
/*
* If the device is not present, it is unnecessary to load device
if (!device->status.present)
return -ENODEV;
- if (device->flags.hardware_id) {
- for (id = ids; id->id[0]; id++) {
- if (!strcmp((char*)id->id, device->pnp.hardware_id))
+ for (id = ids; id->id[0]; id++)
+ list_for_each_entry(hwid, &device->pnp.ids, list)
+ if (!strcmp((char *) id->id, hwid->id))
return 0;
- }
- }
-
- if (device->flags.compatible_ids) {
- struct acpica_device_id_list *cid_list = device->pnp.cid_list;
- int i;
-
- for (id = ids; id->id[0]; id++) {
- /* compare multiple _CID entries against driver ids */
- for (i = 0; i < cid_list->count; i++) {
- if (!strcmp((char*)id->id,
- cid_list->ids[i].string))
- return 0;
- }
- }
- }
return -ENOENT;
}
EXPORT_SYMBOL(acpi_match_device_ids);
+static void acpi_free_ids(struct acpi_device *device)
+{
+ struct acpi_hardware_id *id, *tmp;
+
+ list_for_each_entry_safe(id, tmp, &device->pnp.ids, list) {
+ kfree(id->id);
+ kfree(id);
+ }
+}
+
static void acpi_device_release(struct device *dev)
{
struct acpi_device *acpi_dev = to_acpi_device(dev);
- kfree(acpi_dev->pnp.cid_list);
- if (acpi_dev->flags.hardware_id)
- kfree(acpi_dev->pnp.hardware_id);
- if (acpi_dev->flags.unique_id)
- kfree(acpi_dev->pnp.unique_id);
+ acpi_free_ids(acpi_dev);
kfree(acpi_dev);
}
static int acpi_device_install_notify_handler(struct acpi_device *device)
{
acpi_status status;
- char *hid;
- hid = acpi_device_hid(device);
- if (!strcmp(hid, ACPI_BUTTON_HID_POWERF))
+ if (device->device_type == ACPI_BUS_TYPE_POWER_BUTTON)
status =
acpi_install_fixed_event_handler(ACPI_EVENT_POWER_BUTTON,
acpi_device_notify_fixed,
device);
- else if (!strcmp(hid, ACPI_BUTTON_HID_SLEEPF))
+ else if (device->device_type == ACPI_BUS_TYPE_SLEEP_BUTTON)
status =
acpi_install_fixed_event_handler(ACPI_EVENT_SLEEP_BUTTON,
acpi_device_notify_fixed,
static void acpi_device_remove_notify_handler(struct acpi_device *device)
{
- if (!strcmp(acpi_device_hid(device), ACPI_BUTTON_HID_POWERF))
+ if (device->device_type == ACPI_BUS_TYPE_POWER_BUTTON)
acpi_remove_fixed_event_handler(ACPI_EVENT_POWER_BUTTON,
acpi_device_notify_fixed);
- else if (!strcmp(acpi_device_hid(device), ACPI_BUTTON_HID_SLEEPF))
+ else if (device->device_type == ACPI_BUS_TYPE_SLEEP_BUTTON)
acpi_remove_fixed_event_handler(ACPI_EVENT_SLEEP_BUTTON,
acpi_device_notify_fixed);
else
.uevent = acpi_device_uevent,
};
-static int acpi_device_register(struct acpi_device *device,
- struct acpi_device *parent)
+static int acpi_device_register(struct acpi_device *device)
{
int result;
struct acpi_device_bus_id *acpi_device_bus_id, *new_bus_id;
int found = 0;
+
/*
* Linkage
* -------
* If failed, create one and link it into acpi_bus_id_list
*/
list_for_each_entry(acpi_device_bus_id, &acpi_bus_id_list, node) {
- if(!strcmp(acpi_device_bus_id->bus_id, device->flags.hardware_id? device->pnp.hardware_id : "device")) {
- acpi_device_bus_id->instance_no ++;
+ if (!strcmp(acpi_device_bus_id->bus_id,
+ acpi_device_hid(device))) {
+ acpi_device_bus_id->instance_no++;
found = 1;
kfree(new_bus_id);
break;
}
if (!found) {
acpi_device_bus_id = new_bus_id;
- strcpy(acpi_device_bus_id->bus_id, device->flags.hardware_id ? device->pnp.hardware_id : "device");
+ strcpy(acpi_device_bus_id->bus_id, acpi_device_hid(device));
acpi_device_bus_id->instance_no = 0;
list_add_tail(&acpi_device_bus_id->node, &acpi_bus_id_list);
}
mutex_unlock(&acpi_device_lock);
if (device->parent)
- device->dev.parent = &parent->dev;
+ device->dev.parent = &device->parent->dev;
device->dev.bus = &acpi_bus_type;
device->dev.release = &acpi_device_release;
result = device_register(&device->dev);
/* --------------------------------------------------------------------------
Device Enumeration
-------------------------------------------------------------------------- */
+static struct acpi_device *acpi_bus_get_parent(acpi_handle handle)
+{
+ acpi_status status;
+ int ret;
+ struct acpi_device *device;
+
+ /*
+ * Fixed hardware devices do not appear in the namespace and do not
+ * have handles, but we fabricate acpi_devices for them, so we have
+ * to deal with them specially.
+ */
+ if (handle == NULL)
+ return acpi_root;
+
+ do {
+ status = acpi_get_parent(handle, &handle);
+ if (status == AE_NULL_ENTRY)
+ return NULL;
+ if (ACPI_FAILURE(status))
+ return acpi_root;
+
+ ret = acpi_bus_get_device(handle, &device);
+ if (ret == 0)
+ return device;
+ } while (1);
+}
+
acpi_status
acpi_bus_get_ejd(acpi_handle handle, acpi_handle *ejd)
{
if (ACPI_SUCCESS(status))
device->flags.dynamic_status = 1;
- /* Presence of _CID indicates 'compatible_ids' */
- status = acpi_get_handle(device->handle, "_CID", &temp);
- if (ACPI_SUCCESS(status))
- device->flags.compatible_ids = 1;
-
/* Presence of _RMV indicates 'removable' */
status = acpi_get_handle(device->handle, "_RMV", &temp);
if (ACPI_SUCCESS(status))
return 0;
}
-static void acpi_device_get_busid(struct acpi_device *device,
- acpi_handle handle, int type)
+static void acpi_device_get_busid(struct acpi_device *device)
{
char bus_id[5] = { '?', 0 };
struct acpi_buffer buffer = { sizeof(bus_id), bus_id };
* The device's Bus ID is simply the object name.
* TBD: Shouldn't this value be unique (within the ACPI namespace)?
*/
- switch (type) {
- case ACPI_BUS_TYPE_SYSTEM:
+ if (ACPI_IS_ROOT_DEVICE(device)) {
strcpy(device->pnp.bus_id, "ACPI");
- break;
+ return;
+ }
+
+ switch (device->device_type) {
case ACPI_BUS_TYPE_POWER_BUTTON:
strcpy(device->pnp.bus_id, "PWRF");
break;
strcpy(device->pnp.bus_id, "SLPF");
break;
default:
- acpi_get_name(handle, ACPI_SINGLE_NAME, &buffer);
+ acpi_get_name(device->handle, ACPI_SINGLE_NAME, &buffer);
/* Clean up trailing underscores (if any) */
for (i = 3; i > 1; i--) {
if (bus_id[i] == '_')
return acpi_get_handle(device->handle, "_DCK", &tmp);
}
-static struct acpica_device_id_list*
-acpi_add_cid(
- struct acpi_device_info *info,
- struct acpica_device_id *new_cid)
+char *acpi_device_hid(struct acpi_device *device)
{
- struct acpica_device_id_list *cid;
- char *next_id_string;
- acpi_size cid_length;
- acpi_size new_cid_length;
- u32 i;
-
-
- /* Allocate new CID list with room for the new CID */
-
- if (!new_cid)
- new_cid_length = info->compatible_id_list.list_size;
- else if (info->compatible_id_list.list_size)
- new_cid_length = info->compatible_id_list.list_size +
- new_cid->length + sizeof(struct acpica_device_id);
- else
- new_cid_length = sizeof(struct acpica_device_id_list) + new_cid->length;
-
- cid = ACPI_ALLOCATE_ZEROED(new_cid_length);
- if (!cid) {
- return NULL;
- }
-
- cid->list_size = new_cid_length;
- cid->count = info->compatible_id_list.count;
- if (new_cid)
- cid->count++;
- next_id_string = (char *) cid->ids + (cid->count * sizeof(struct acpica_device_id));
-
- /* Copy all existing CIDs */
-
- for (i = 0; i < info->compatible_id_list.count; i++) {
- cid_length = info->compatible_id_list.ids[i].length;
- cid->ids[i].string = next_id_string;
- cid->ids[i].length = cid_length;
+ struct acpi_hardware_id *hid;
- ACPI_MEMCPY(next_id_string, info->compatible_id_list.ids[i].string,
- cid_length);
-
- next_id_string += cid_length;
- }
+ hid = list_first_entry(&device->pnp.ids, struct acpi_hardware_id, list);
+ return hid->id;
+}
+EXPORT_SYMBOL(acpi_device_hid);
- /* Append the new CID */
+static void acpi_add_id(struct acpi_device *device, const char *dev_id)
+{
+ struct acpi_hardware_id *id;
- if (new_cid) {
- cid->ids[i].string = next_id_string;
- cid->ids[i].length = new_cid->length;
+ id = kmalloc(sizeof(*id), GFP_KERNEL);
+ if (!id)
+ return;
- ACPI_MEMCPY(next_id_string, new_cid->string, new_cid->length);
+ id->id = kmalloc(strlen(dev_id) + 1, GFP_KERNEL);
+ if (!id->id) {
+ kfree(id);
+ return;
}
- return cid;
+ strcpy(id->id, dev_id);
+ list_add_tail(&id->list, &device->pnp.ids);
}
-static void acpi_device_set_id(struct acpi_device *device,
- struct acpi_device *parent, acpi_handle handle,
- int type)
+static void acpi_device_set_id(struct acpi_device *device)
{
- struct acpi_device_info *info = NULL;
- char *hid = NULL;
- char *uid = NULL;
- struct acpica_device_id_list *cid_list = NULL;
- char *cid_add = NULL;
acpi_status status;
+ struct acpi_device_info *info;
+ struct acpica_device_id_list *cid_list;
+ int i;
- switch (type) {
+ switch (device->device_type) {
case ACPI_BUS_TYPE_DEVICE:
- status = acpi_get_object_info(handle, &info);
+ if (ACPI_IS_ROOT_DEVICE(device)) {
+ acpi_add_id(device, ACPI_SYSTEM_HID);
+ break;
+ } else if (ACPI_IS_ROOT_DEVICE(device->parent)) {
+ /* \_SB_, the only root-level namespace device */
+ acpi_add_id(device, ACPI_BUS_HID);
+ strcpy(device->pnp.device_name, ACPI_BUS_DEVICE_NAME);
+ strcpy(device->pnp.device_class, ACPI_BUS_CLASS);
+ break;
+ }
+
+ status = acpi_get_object_info(device->handle, &info);
if (ACPI_FAILURE(status)) {
printk(KERN_ERR PREFIX "%s: Error reading device info\n", __func__);
return;
}
if (info->valid & ACPI_VALID_HID)
- hid = info->hardware_id.string;
- if (info->valid & ACPI_VALID_UID)
- uid = info->unique_id.string;
- if (info->valid & ACPI_VALID_CID)
+ acpi_add_id(device, info->hardware_id.string);
+ if (info->valid & ACPI_VALID_CID) {
cid_list = &info->compatible_id_list;
+ for (i = 0; i < cid_list->count; i++)
+ acpi_add_id(device, cid_list->ids[i].string);
+ }
if (info->valid & ACPI_VALID_ADR) {
device->pnp.bus_address = info->address;
device->flags.bus_address = 1;
}
- /* If we have a video/bay/dock device, add our selfdefined
- HID to the CID list. Like that the video/bay/dock drivers
- will get autoloaded and the device might still match
- against another driver.
- */
+ kfree(info);
+
+ /*
+ * Some devices don't reliably have _HIDs & _CIDs, so add
+ * synthetic HIDs to make sure drivers can find them.
+ */
if (acpi_is_video_device(device))
- cid_add = ACPI_VIDEO_HID;
+ acpi_add_id(device, ACPI_VIDEO_HID);
else if (ACPI_SUCCESS(acpi_bay_match(device)))
- cid_add = ACPI_BAY_HID;
+ acpi_add_id(device, ACPI_BAY_HID);
else if (ACPI_SUCCESS(acpi_dock_match(device)))
- cid_add = ACPI_DOCK_HID;
+ acpi_add_id(device, ACPI_DOCK_HID);
break;
case ACPI_BUS_TYPE_POWER:
- hid = ACPI_POWER_HID;
+ acpi_add_id(device, ACPI_POWER_HID);
break;
case ACPI_BUS_TYPE_PROCESSOR:
- hid = ACPI_PROCESSOR_OBJECT_HID;
- break;
- case ACPI_BUS_TYPE_SYSTEM:
- hid = ACPI_SYSTEM_HID;
+ acpi_add_id(device, ACPI_PROCESSOR_OBJECT_HID);
break;
case ACPI_BUS_TYPE_THERMAL:
- hid = ACPI_THERMAL_HID;
+ acpi_add_id(device, ACPI_THERMAL_HID);
break;
case ACPI_BUS_TYPE_POWER_BUTTON:
- hid = ACPI_BUTTON_HID_POWERF;
+ acpi_add_id(device, ACPI_BUTTON_HID_POWERF);
break;
case ACPI_BUS_TYPE_SLEEP_BUTTON:
- hid = ACPI_BUTTON_HID_SLEEPF;
+ acpi_add_id(device, ACPI_BUTTON_HID_SLEEPF);
break;
}
/*
- * \_SB
- * ----
- * Fix for the system root bus device -- the only root-level device.
+ * We build acpi_devices for some objects that don't have _HID or _CID,
+ * e.g., PCI bridges and slots. Drivers can't bind to these objects,
+ * but we do use them indirectly by traversing the acpi_device tree.
+ * This generic ID isn't useful for driver binding, but it provides
+ * the useful property that "every acpi_device has an ID."
*/
- if (((acpi_handle)parent == ACPI_ROOT_OBJECT) && (type == ACPI_BUS_TYPE_DEVICE)) {
- hid = ACPI_BUS_HID;
- strcpy(device->pnp.device_name, ACPI_BUS_DEVICE_NAME);
- strcpy(device->pnp.device_class, ACPI_BUS_CLASS);
- }
-
- if (hid) {
- device->pnp.hardware_id = ACPI_ALLOCATE_ZEROED(strlen (hid) + 1);
- if (device->pnp.hardware_id) {
- strcpy(device->pnp.hardware_id, hid);
- device->flags.hardware_id = 1;
- }
- }
- if (!device->flags.hardware_id)
- device->pnp.hardware_id = "";
-
- if (uid) {
- device->pnp.unique_id = ACPI_ALLOCATE_ZEROED(strlen (uid) + 1);
- if (device->pnp.unique_id) {
- strcpy(device->pnp.unique_id, uid);
- device->flags.unique_id = 1;
- }
- }
- if (!device->flags.unique_id)
- device->pnp.unique_id = "";
-
- if (cid_list || cid_add) {
- struct acpica_device_id_list *list;
-
- if (cid_add) {
- struct acpica_device_id cid;
- cid.length = strlen (cid_add) + 1;
- cid.string = cid_add;
-
- list = acpi_add_cid(info, &cid);
- } else {
- list = acpi_add_cid(info, NULL);
- }
-
- if (list) {
- device->pnp.cid_list = list;
- if (cid_add)
- device->flags.compatible_ids = 1;
- }
- }
-
- kfree(info);
+ if (list_empty(&device->pnp.ids))
+ acpi_add_id(device, "device");
}
-static int acpi_device_set_context(struct acpi_device *device, int type)
+static int acpi_device_set_context(struct acpi_device *device)
{
- acpi_status status = AE_OK;
- int result = 0;
+ acpi_status status;
+
/*
* Context
* -------
* Attach this 'struct acpi_device' to the ACPI object. This makes
- * resolutions from handle->device very efficient. Note that we need
- * to be careful with fixed-feature devices as they all attach to the
- * root object.
+ * resolutions from handle->device very efficient. Fixed hardware
+ * devices have no handles, so we skip them.
*/
- if (type != ACPI_BUS_TYPE_POWER_BUTTON &&
- type != ACPI_BUS_TYPE_SLEEP_BUTTON) {
- status = acpi_attach_data(device->handle,
- acpi_bus_data_handler, device);
+ if (!device->handle)
+ return 0;
- if (ACPI_FAILURE(status)) {
- printk(KERN_ERR PREFIX "Error attaching device data\n");
- result = -ENODEV;
- }
- }
- return result;
+ status = acpi_attach_data(device->handle,
+ acpi_bus_data_handler, device);
+ if (ACPI_SUCCESS(status))
+ return 0;
+
+ printk(KERN_ERR PREFIX "Error attaching device data\n");
+ return -ENODEV;
}
static int acpi_bus_remove(struct acpi_device *dev, int rmdevice)
return 0;
}
-static int
-acpi_add_single_object(struct acpi_device **child,
- struct acpi_device *parent, acpi_handle handle, int type,
- struct acpi_bus_ops *ops)
+static int acpi_add_single_object(struct acpi_device **child,
+ acpi_handle handle, int type,
+ unsigned long long sta,
+ struct acpi_bus_ops *ops)
{
- int result = 0;
- struct acpi_device *device = NULL;
-
-
- if (!child)
- return -EINVAL;
+ int result;
+ struct acpi_device *device;
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
device = kzalloc(sizeof(struct acpi_device), GFP_KERNEL);
if (!device) {
return -ENOMEM;
}
+ INIT_LIST_HEAD(&device->pnp.ids);
+ device->device_type = type;
device->handle = handle;
- device->parent = parent;
+ device->parent = acpi_bus_get_parent(handle);
device->bus_ops = *ops; /* workround for not call .start */
+ STRUCT_TO_INT(device->status) = sta;
-
- acpi_device_get_busid(device, handle, type);
+ acpi_device_get_busid(device);
/*
* Flags
* -----
- * Get prior to calling acpi_bus_get_status() so we know whether
- * or not _STA is present. Note that we only look for object
- * handles -- cannot evaluate objects until we know the device is
- * present and properly initialized.
+ * Note that we only look for object handles -- cannot evaluate objects
+ * until we know the device is present and properly initialized.
*/
result = acpi_bus_get_flags(device);
if (result)
goto end;
- /*
- * Status
- * ------
- * See if the device is present. We always assume that non-Device
- * and non-Processor objects (e.g. thermal zones, power resources,
- * etc.) are present, functioning, etc. (at least when parent object
- * is present). Note that _STA has a different meaning for some
- * objects (e.g. power resources) so we need to be careful how we use
- * it.
- */
- switch (type) {
- case ACPI_BUS_TYPE_PROCESSOR:
- case ACPI_BUS_TYPE_DEVICE:
- result = acpi_bus_get_status(device);
- if (ACPI_FAILURE(result)) {
- result = -ENODEV;
- goto end;
- }
- /*
- * When the device is neither present nor functional, the
- * device should not be added to Linux ACPI device tree.
- * When the status of the device is not present but functinal,
- * it should be added to Linux ACPI tree. For example : bay
- * device , dock device.
- * In such conditions it is unncessary to check whether it is
- * bay device or dock device.
- */
- if (!device->status.present && !device->status.functional) {
- result = -ENODEV;
- goto end;
- }
- break;
- default:
- STRUCT_TO_INT(device->status) =
- ACPI_STA_DEVICE_PRESENT | ACPI_STA_DEVICE_ENABLED |
- ACPI_STA_DEVICE_UI | ACPI_STA_DEVICE_FUNCTIONING;
- break;
- }
-
/*
* Initialize Device
* -----------------
* TBD: Synch with Core's enumeration/initialization process.
*/
-
- /*
- * Hardware ID, Unique ID, & Bus Address
- * -------------------------------------
- */
- acpi_device_set_id(device, parent, handle, type);
+ acpi_device_set_id(device);
/*
* Power Management
goto end;
}
- if ((result = acpi_device_set_context(device, type)))
+ if ((result = acpi_device_set_context(device)))
goto end;
- result = acpi_device_register(device, parent);
+ result = acpi_device_register(device);
/*
* Bind _ADR-Based Devices when hot add
}
end:
- if (!result)
+ if (!result) {
+ acpi_get_name(handle, ACPI_FULL_PATHNAME, &buffer);
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO,
+ "Adding %s [%s] parent %s\n", dev_name(&device->dev),
+ (char *) buffer.pointer,
+ device->parent ? dev_name(&device->parent->dev) :
+ "(null)"));
+ kfree(buffer.pointer);
*child = device;
- else
+ } else
acpi_device_release(&device->dev);
return result;
}
-static int acpi_bus_scan(struct acpi_device *start, struct acpi_bus_ops *ops)
-{
- acpi_status status = AE_OK;
- struct acpi_device *parent = NULL;
- struct acpi_device *child = NULL;
- acpi_handle phandle = NULL;
- acpi_handle chandle = NULL;
- acpi_object_type type = 0;
- u32 level = 1;
-
+#define ACPI_STA_DEFAULT (ACPI_STA_DEVICE_PRESENT | ACPI_STA_DEVICE_ENABLED | \
+ ACPI_STA_DEVICE_UI | ACPI_STA_DEVICE_FUNCTIONING)
- if (!start)
- return -EINVAL;
+static int acpi_bus_type_and_status(acpi_handle handle, int *type,
+ unsigned long long *sta)
+{
+ acpi_status status;
+ acpi_object_type acpi_type;
- parent = start;
- phandle = start->handle;
+ status = acpi_get_type(handle, &acpi_type);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
- /*
- * Parse through the ACPI namespace, identify all 'devices', and
- * create a new 'struct acpi_device' for each.
- */
- while ((level > 0) && parent) {
+ switch (acpi_type) {
+ case ACPI_TYPE_ANY: /* for ACPI_ROOT_OBJECT */
+ case ACPI_TYPE_DEVICE:
+ *type = ACPI_BUS_TYPE_DEVICE;
+ status = acpi_bus_get_status_handle(handle, sta);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
+ break;
+ case ACPI_TYPE_PROCESSOR:
+ *type = ACPI_BUS_TYPE_PROCESSOR;
+ status = acpi_bus_get_status_handle(handle, sta);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
+ break;
+ case ACPI_TYPE_THERMAL:
+ *type = ACPI_BUS_TYPE_THERMAL;
+ *sta = ACPI_STA_DEFAULT;
+ break;
+ case ACPI_TYPE_POWER:
+ *type = ACPI_BUS_TYPE_POWER;
+ *sta = ACPI_STA_DEFAULT;
+ break;
+ default:
+ return -ENODEV;
+ }
- status = acpi_get_next_object(ACPI_TYPE_ANY, phandle,
- chandle, &chandle);
+ return 0;
+}
- /*
- * If this scope is exhausted then move our way back up.
- */
- if (ACPI_FAILURE(status)) {
- level--;
- chandle = phandle;
- acpi_get_parent(phandle, &phandle);
- if (parent->parent)
- parent = parent->parent;
- continue;
- }
+static acpi_status acpi_bus_check_add(acpi_handle handle, u32 lvl,
+ void *context, void **return_value)
+{
+ struct acpi_bus_ops *ops = context;
+ int type;
+ unsigned long long sta;
+ struct acpi_device *device;
+ acpi_status status;
+ int result;
- status = acpi_get_type(chandle, &type);
- if (ACPI_FAILURE(status))
- continue;
+ result = acpi_bus_type_and_status(handle, &type, &sta);
+ if (result)
+ return AE_OK;
- /*
- * If this is a scope object then parse it (depth-first).
- */
- if (type == ACPI_TYPE_LOCAL_SCOPE) {
- level++;
- phandle = chandle;
- chandle = NULL;
- continue;
- }
+ if (!(sta & ACPI_STA_DEVICE_PRESENT) &&
+ !(sta & ACPI_STA_DEVICE_FUNCTIONING))
+ return AE_CTRL_DEPTH;
- /*
- * We're only interested in objects that we consider 'devices'.
- */
- switch (type) {
- case ACPI_TYPE_DEVICE:
- type = ACPI_BUS_TYPE_DEVICE;
- break;
- case ACPI_TYPE_PROCESSOR:
- type = ACPI_BUS_TYPE_PROCESSOR;
- break;
- case ACPI_TYPE_THERMAL:
- type = ACPI_BUS_TYPE_THERMAL;
- break;
- case ACPI_TYPE_POWER:
- type = ACPI_BUS_TYPE_POWER;
- break;
- default:
- continue;
- }
+ /*
+ * We may already have an acpi_device from a previous enumeration. If
+ * so, we needn't add it again, but we may still have to start it.
+ */
+ device = NULL;
+ acpi_bus_get_device(handle, &device);
+ if (ops->acpi_op_add && !device)
+ acpi_add_single_object(&device, handle, type, sta, ops);
- if (ops->acpi_op_add)
- status = acpi_add_single_object(&child, parent,
- chandle, type, ops);
- else
- status = acpi_bus_get_device(chandle, &child);
+ if (!device)
+ return AE_CTRL_DEPTH;
+ if (ops->acpi_op_start && !(ops->acpi_op_add)) {
+ status = acpi_start_single_object(device);
if (ACPI_FAILURE(status))
- continue;
+ return AE_CTRL_DEPTH;
+ }
- if (ops->acpi_op_start && !(ops->acpi_op_add)) {
- status = acpi_start_single_object(child);
- if (ACPI_FAILURE(status))
- continue;
- }
+ if (!*return_value)
+ *return_value = device;
+ return AE_OK;
+}
- /*
- * If the device is present, enabled, and functioning then
- * parse its scope (depth-first). Note that we need to
- * represent absent devices to facilitate PnP notifications
- * -- but only the subtree head (not all of its children,
- * which will be enumerated when the parent is inserted).
- *
- * TBD: Need notifications and other detection mechanisms
- * in place before we can fully implement this.
- */
- /*
- * When the device is not present but functional, it is also
- * necessary to scan the children of this device.
- */
- if (child->status.present || (!child->status.present &&
- child->status.functional)) {
- status = acpi_get_next_object(ACPI_TYPE_ANY, chandle,
- NULL, NULL);
- if (ACPI_SUCCESS(status)) {
- level++;
- phandle = chandle;
- chandle = NULL;
- parent = child;
- }
- }
- }
+static int acpi_bus_scan(acpi_handle handle, struct acpi_bus_ops *ops,
+ struct acpi_device **child)
+{
+ acpi_status status;
+ void *device = NULL;
+
+ status = acpi_bus_check_add(handle, 0, ops, &device);
+ if (ACPI_SUCCESS(status))
+ acpi_walk_namespace(ACPI_TYPE_ANY, handle, ACPI_UINT32_MAX,
+ acpi_bus_check_add, ops, &device);
+ if (child)
+ *child = device;
return 0;
}
acpi_bus_add(struct acpi_device **child,
struct acpi_device *parent, acpi_handle handle, int type)
{
- int result;
struct acpi_bus_ops ops;
memset(&ops, 0, sizeof(ops));
ops.acpi_op_add = 1;
- result = acpi_add_single_object(child, parent, handle, type, &ops);
- if (!result)
- result = acpi_bus_scan(*child, &ops);
-
- return result;
+ acpi_bus_scan(handle, &ops, child);
+ return 0;
}
EXPORT_SYMBOL(acpi_bus_add);
int acpi_bus_start(struct acpi_device *device)
{
- int result;
struct acpi_bus_ops ops;
+ memset(&ops, 0, sizeof(ops));
+ ops.acpi_op_start = 1;
- if (!device)
- return -EINVAL;
-
- result = acpi_start_single_object(device);
- if (!result) {
- memset(&ops, 0, sizeof(ops));
- ops.acpi_op_start = 1;
- result = acpi_bus_scan(device, &ops);
- }
- return result;
+ acpi_bus_scan(device->handle, &ops, NULL);
+ return 0;
}
EXPORT_SYMBOL(acpi_bus_start);
}
EXPORT_SYMBOL_GPL(acpi_bus_trim);
-static int acpi_bus_scan_fixed(struct acpi_device *root)
+static int acpi_bus_scan_fixed(void)
{
int result = 0;
struct acpi_device *device = NULL;
struct acpi_bus_ops ops;
- if (!root)
- return -ENODEV;
-
memset(&ops, 0, sizeof(ops));
ops.acpi_op_add = 1;
ops.acpi_op_start = 1;
* Enumerate all fixed-feature devices.
*/
if ((acpi_gbl_FADT.flags & ACPI_FADT_POWER_BUTTON) == 0) {
- result = acpi_add_single_object(&device, acpi_root,
- NULL,
+ result = acpi_add_single_object(&device, NULL,
ACPI_BUS_TYPE_POWER_BUTTON,
+ ACPI_STA_DEFAULT,
&ops);
}
if ((acpi_gbl_FADT.flags & ACPI_FADT_SLEEP_BUTTON) == 0) {
- result = acpi_add_single_object(&device, acpi_root,
- NULL,
+ result = acpi_add_single_object(&device, NULL,
ACPI_BUS_TYPE_SLEEP_BUTTON,
+ ACPI_STA_DEFAULT,
&ops);
}
printk(KERN_ERR PREFIX "Could not register bus type\n");
}
- /*
- * Create the root device in the bus's device tree
- */
- result = acpi_add_single_object(&acpi_root, NULL, ACPI_ROOT_OBJECT,
- ACPI_BUS_TYPE_SYSTEM, &ops);
- if (result)
- goto Done;
-
/*
* Enumerate devices in the ACPI namespace.
*/
- result = acpi_bus_scan_fixed(acpi_root);
+ result = acpi_bus_scan(ACPI_ROOT_OBJECT, &ops, &acpi_root);
if (!result)
- result = acpi_bus_scan(acpi_root, &ops);
+ result = acpi_bus_scan_fixed();
if (result)
acpi_device_unregister(acpi_root, ACPI_BUS_REMOVAL_NORMAL);
-Done:
return result;
}
struct file *file);
static ssize_t acpi_video_device_write_brightness(struct file *file,
const char __user *buffer, size_t count, loff_t *data);
-static struct file_operations acpi_video_device_brightness_fops = {
+static const struct file_operations acpi_video_device_brightness_fops = {
.owner = THIS_MODULE,
.open = acpi_video_device_brightness_open_fs,
.read = seq_read,
result = acpi_video_device_lcd_set_level(device, level_next);
+ if (!result)
+ backlight_force_update(device->backlight,
+ BACKLIGHT_UPDATE_HOTKEY);
+
out:
if (result)
printk(KERN_ERR PREFIX "Failed to switch the brightness\n");
return;
}
-/********** Set socket options for a VC **********/
-
-// int amb_getsockopt (struct atm_vcc * atm_vcc, int level, int optname, void * optval, int optlen);
-
-/********** Set socket options for a VC **********/
-
-// int amb_setsockopt (struct atm_vcc * atm_vcc, int level, int optname, void * optval, int optlen);
-
/********** Send **********/
static int amb_send (struct atm_vcc * atm_vcc, struct sk_buff * skb) {
static int eni_setsockopt(struct atm_vcc *vcc,int level,int optname,
- void __user *optval,int optlen)
+ void __user *optval,unsigned int optlen)
{
return -EINVAL;
}
static int fs_setsockopt(struct atm_vcc *vcc,int level,int optname,
- void __user *optval,int optlen)
+ void __user *optval,unsigned int optlen)
{
func_enter ();
func_exit ();
static int
-fore200e_setsockopt(struct atm_vcc* vcc, int level, int optname, void __user *optval, int optlen)
+fore200e_setsockopt(struct atm_vcc* vcc, int level, int optname, void __user *optval, unsigned int optlen)
{
/* struct fore200e* fore200e = FORE200E_DEV(vcc->dev); */
he_dev->rbps_base = pci_alloc_consistent(he_dev->pci_dev,
CONFIG_RBPS_SIZE * sizeof(struct he_rbp), &he_dev->rbps_phys);
if (he_dev->rbps_base == NULL) {
- hprintk("failed to alloc rbps\n");
- return -ENOMEM;
+ hprintk("failed to alloc rbps_base\n");
+ goto out_destroy_rbps_pool;
}
memset(he_dev->rbps_base, 0, CONFIG_RBPS_SIZE * sizeof(struct he_rbp));
he_dev->rbps_virt = kmalloc(CONFIG_RBPS_SIZE * sizeof(struct he_virt), GFP_KERNEL);
+ if (he_dev->rbps_virt == NULL) {
+ hprintk("failed to alloc rbps_virt\n");
+ goto out_free_rbps_base;
+ }
for (i = 0; i < CONFIG_RBPS_SIZE; ++i) {
dma_addr_t dma_handle;
cpuaddr = pci_pool_alloc(he_dev->rbps_pool, GFP_KERNEL|GFP_DMA, &dma_handle);
if (cpuaddr == NULL)
- return -ENOMEM;
+ goto out_free_rbps_virt;
he_dev->rbps_virt[i].virt = cpuaddr;
he_dev->rbps_base[i].status = RBP_LOANED | RBP_SMALLBUF | (i << RBP_INDEX_OFF);
CONFIG_RBPL_BUFSIZE, 8, 0);
if (he_dev->rbpl_pool == NULL) {
hprintk("unable to create rbpl pool\n");
- return -ENOMEM;
+ goto out_free_rbps_virt;
}
he_dev->rbpl_base = pci_alloc_consistent(he_dev->pci_dev,
CONFIG_RBPL_SIZE * sizeof(struct he_rbp), &he_dev->rbpl_phys);
if (he_dev->rbpl_base == NULL) {
- hprintk("failed to alloc rbpl\n");
- return -ENOMEM;
+ hprintk("failed to alloc rbpl_base\n");
+ goto out_destroy_rbpl_pool;
}
memset(he_dev->rbpl_base, 0, CONFIG_RBPL_SIZE * sizeof(struct he_rbp));
he_dev->rbpl_virt = kmalloc(CONFIG_RBPL_SIZE * sizeof(struct he_virt), GFP_KERNEL);
+ if (he_dev->rbpl_virt == NULL) {
+ hprintk("failed to alloc rbpl_virt\n");
+ goto out_free_rbpl_base;
+ }
for (i = 0; i < CONFIG_RBPL_SIZE; ++i) {
dma_addr_t dma_handle;
cpuaddr = pci_pool_alloc(he_dev->rbpl_pool, GFP_KERNEL|GFP_DMA, &dma_handle);
if (cpuaddr == NULL)
- return -ENOMEM;
+ goto out_free_rbpl_virt;
he_dev->rbpl_virt[i].virt = cpuaddr;
he_dev->rbpl_base[i].status = RBP_LOANED | (i << RBP_INDEX_OFF);
CONFIG_RBRQ_SIZE * sizeof(struct he_rbrq), &he_dev->rbrq_phys);
if (he_dev->rbrq_base == NULL) {
hprintk("failed to allocate rbrq\n");
- return -ENOMEM;
+ goto out_free_rbpl_virt;
}
memset(he_dev->rbrq_base, 0, CONFIG_RBRQ_SIZE * sizeof(struct he_rbrq));
CONFIG_TBRQ_SIZE * sizeof(struct he_tbrq), &he_dev->tbrq_phys);
if (he_dev->tbrq_base == NULL) {
hprintk("failed to allocate tbrq\n");
- return -ENOMEM;
+ goto out_free_rbpq_base;
}
memset(he_dev->tbrq_base, 0, CONFIG_TBRQ_SIZE * sizeof(struct he_tbrq));
he_writel(he_dev, CONFIG_TBRQ_THRESH, G0_TBRQ_THRESH + (group * 16));
return 0;
+
+out_free_rbpq_base:
+ pci_free_consistent(he_dev->pci_dev, CONFIG_RBRQ_SIZE *
+ sizeof(struct he_rbrq), he_dev->rbrq_base,
+ he_dev->rbrq_phys);
+ i = CONFIG_RBPL_SIZE;
+out_free_rbpl_virt:
+ while (i--)
+ pci_pool_free(he_dev->rbpl_pool, he_dev->rbpl_virt[i].virt,
+ he_dev->rbpl_base[i].phys);
+ kfree(he_dev->rbpl_virt);
+
+out_free_rbpl_base:
+ pci_free_consistent(he_dev->pci_dev, CONFIG_RBPL_SIZE *
+ sizeof(struct he_rbp), he_dev->rbpl_base,
+ he_dev->rbpl_phys);
+out_destroy_rbpl_pool:
+ pci_pool_destroy(he_dev->rbpl_pool);
+
+ i = CONFIG_RBPS_SIZE;
+out_free_rbps_virt:
+ while (i--)
+ pci_pool_free(he_dev->rbps_pool, he_dev->rbps_virt[i].virt,
+ he_dev->rbps_base[i].phys);
+ kfree(he_dev->rbps_virt);
+
+out_free_rbps_base:
+ pci_free_consistent(he_dev->pci_dev, CONFIG_RBPS_SIZE *
+ sizeof(struct he_rbp), he_dev->rbps_base,
+ he_dev->rbps_phys);
+out_destroy_rbps_pool:
+ pci_pool_destroy(he_dev->rbps_pool);
+ return -ENOMEM;
}
static int __devinit
}
static int hrz_setsockopt (struct atm_vcc * atm_vcc, int level, int optname,
- void *optval, int optlen) {
+ void *optval, unsigned int optlen) {
hrz_dev * dev = HRZ_DEV(atm_vcc->dev);
PRINTD (DBG_FLOW|DBG_VCC, "hrz_setsockopt");
switch (level) {
}
static int ia_setsockopt(struct atm_vcc *vcc, int level, int optname,
- void __user *optval, int optlen)
+ void __user *optval, unsigned int optlen)
{
IF_EVENT(printk(">ia_setsockopt\n");)
return -EINVAL;
SOLOS_ATTR_RO(RSUnCorrectedErrorsUp)
SOLOS_ATTR_RO(InterleaveRDn)
SOLOS_ATTR_RO(InterleaveRUp)
+SOLOS_ATTR_RO(BisRDn)
+SOLOS_ATTR_RO(BisRUp)
+SOLOS_ATTR_RO(INPdown)
+SOLOS_ATTR_RO(INPup)
SOLOS_ATTR_RO(ShowtimeStart)
SOLOS_ATTR_RO(ATURVendor)
SOLOS_ATTR_RO(ATUCCountry)
SOLOS_ATTR_RW(LineMode)
SOLOS_ATTR_RW(Profile)
SOLOS_ATTR_RW(DetectNoise)
+SOLOS_ATTR_RW(BisAForceSNRMarginDn)
+SOLOS_ATTR_RW(BisMForceSNRMarginDn)
+SOLOS_ATTR_RW(BisAMaxMargin)
+SOLOS_ATTR_RW(BisMMaxMargin)
+SOLOS_ATTR_RW(AnnexAForceSNRMarginDn)
+SOLOS_ATTR_RW(AnnexAMaxMargin)
+SOLOS_ATTR_RW(AnnexMMaxMargin)
SOLOS_ATTR_RO(SupportedAnnexes)
SOLOS_ATTR_RO(Status)
SOLOS_ATTR_RO(TotalStart)
#define RX_DMA_ADDR(port) (0x30 + (4 * (port)))
#define DATA_RAM_SIZE 32768
-#define BUF_SIZE 4096
+#define BUF_SIZE 2048
+#define OLD_BUF_SIZE 4096 /* For FPGA versions <= 2*/
#define FPGA_PAGE 528 /* FPGA flash page size*/
#define SOLOS_PAGE 512 /* Solos flash page size*/
#define FPGA_BLOCK (FPGA_PAGE * 8) /* FPGA flash block size*/
#define SOLOS_BLOCK (SOLOS_PAGE * 8) /* Solos flash block size*/
-#define RX_BUF(card, nr) ((card->buffers) + (nr)*BUF_SIZE*2)
-#define TX_BUF(card, nr) ((card->buffers) + (nr)*BUF_SIZE*2 + BUF_SIZE)
+#define RX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2)
+#define TX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2 + (card->buffer_size))
+#define FLASH_BUF ((card->buffers) + 4*(card->buffer_size)*2)
#define RX_DMA_SIZE 2048
+#define FPGA_VERSION(a,b) (((a) << 8) + (b))
+#define LEGACY_BUFFERS 2
+#define DMA_SUPPORTED 4
+
static int reset = 0;
static int atmdebug = 0;
static int firmware_upgrade = 0;
static int fpga_upgrade = 0;
+static int db_firmware_upgrade = 0;
+static int db_fpga_upgrade = 0;
struct pkt_hdr {
__le16 size;
wait_queue_head_t param_wq;
wait_queue_head_t fw_wq;
int using_dma;
+ int fpga_version;
+ int buffer_size;
};
MODULE_PARM_DESC(atmdebug, "Print ATM data");
MODULE_PARM_DESC(firmware_upgrade, "Initiate Solos firmware upgrade");
MODULE_PARM_DESC(fpga_upgrade, "Initiate FPGA upgrade");
+MODULE_PARM_DESC(db_firmware_upgrade, "Initiate daughter board Solos firmware upgrade");
+MODULE_PARM_DESC(db_fpga_upgrade, "Initiate daughter board FPGA upgrade");
module_param(reset, int, 0444);
module_param(atmdebug, int, 0644);
module_param(firmware_upgrade, int, 0444);
module_param(fpga_upgrade, int, 0444);
+module_param(db_firmware_upgrade, int, 0444);
+module_param(db_fpga_upgrade, int, 0444);
static void fpga_queue(struct solos_card *card, int port, struct sk_buff *skb,
struct atm_vcc *vcc);
if (chip == 0) {
fw_name = "solos-FPGA.bin";
blocksize = FPGA_BLOCK;
- } else {
+ }
+
+ if (chip == 1) {
fw_name = "solos-Firmware.bin";
blocksize = SOLOS_BLOCK;
}
+
+ if (chip == 2){
+ if (card->fpga_version > LEGACY_BUFFERS){
+ fw_name = "solos-db-FPGA.bin";
+ blocksize = FPGA_BLOCK;
+ } else {
+ dev_info(&card->dev->dev, "FPGA version doesn't support daughter board upgrades\n");
+ return -EPERM;
+ }
+ }
+
+ if (chip == 3){
+ if (card->fpga_version > LEGACY_BUFFERS){
+ fw_name = "solos-Firmware.bin";
+ blocksize = SOLOS_BLOCK;
+ } else {
+ dev_info(&card->dev->dev, "FPGA version doesn't support daughter board upgrades\n");
+ return -EPERM;
+ }
+ }
if (request_firmware(&fw, fw_name, &card->dev->dev))
return -ENOENT;
data32 = ioread32(card->config_regs + FPGA_MODE);
/* Set mode to Chip Erase */
- dev_info(&card->dev->dev, "Set FPGA Flash mode to %s Chip Erase\n",
- chip?"Solos":"FPGA");
+ if(chip == 0 || chip == 2)
+ dev_info(&card->dev->dev, "Set FPGA Flash mode to FPGA Chip Erase\n");
+ if(chip == 1 || chip == 3)
+ dev_info(&card->dev->dev, "Set FPGA Flash mode to Solos Chip Erase\n");
iowrite32((chip * 2), card->config_regs + FLASH_MODE);
/* Copy block to buffer, swapping each 16 bits */
for(i = 0; i < blocksize; i += 4) {
uint32_t word = swahb32p((uint32_t *)(fw->data + offset + i));
- iowrite32(word, RX_BUF(card, 3) + i);
+ if(card->fpga_version > LEGACY_BUFFERS)
+ iowrite32(word, FLASH_BUF + i);
+ else
+ iowrite32(word, RX_BUF(card, 3) + i);
}
/* Specify block number and then trigger flash write */
memcpy_fromio(header, RX_BUF(card, port), sizeof(*header));
size = le16_to_cpu(header->size);
+ if (size > (card->buffer_size - sizeof(*header))){
+ dev_warn(&card->dev->dev, "Invalid buffer size\n");
+ continue;
+ }
skb = alloc_skb(size + 1, GFP_ATOMIC);
if (!skb) {
fpga_ver = (data32 & 0x0000FFFF);
major_ver = ((data32 & 0xFF000000) >> 24);
minor_ver = ((data32 & 0x00FF0000) >> 16);
+ card->fpga_version = FPGA_VERSION(major_ver,minor_ver);
+ if (card->fpga_version > LEGACY_BUFFERS)
+ card->buffer_size = BUF_SIZE;
+ else
+ card->buffer_size = OLD_BUF_SIZE;
dev_info(&dev->dev, "Solos FPGA Version %d.%02d svn-%d\n",
major_ver, minor_ver, fpga_ver);
- if (0 && fpga_ver > 27)
+ if (card->fpga_version >= DMA_SUPPORTED){
card->using_dma = 1;
- else {
+ } else {
+ card->using_dma = 0;
/* Set RX empty flag for all ports */
iowrite32(0xF0, card->config_regs + FLAGS_ADDR);
}
if (firmware_upgrade)
flash_upgrade(card, 1);
+ if (db_fpga_upgrade)
+ flash_upgrade(card, 2);
+
+ if (db_firmware_upgrade)
+ flash_upgrade(card, 3);
+
err = atm_init(card);
if (err)
goto out_free_irq;
static int zatm_setsockopt(struct atm_vcc *vcc,int level,int optname,
- void __user *optval,int optlen)
+ void __user *optval,unsigned int optlen)
{
return -EINVAL;
}
#include <linux/slab.h>
#include <linux/smp_lock.h>
#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
#include <linux/reboot.h>
#include <linux/spinlock.h>
#include <linux/timer.h>
return true;
}
-
-/*
- DAC960_ProcReadStatus implements reading /proc/rd/status.
-*/
-
-static int DAC960_ProcReadStatus(char *Page, char **Start, off_t Offset,
- int Count, int *EOF, void *Data)
+static int dac960_proc_show(struct seq_file *m, void *v)
{
unsigned char *StatusMessage = "OK\n";
- int ControllerNumber, BytesAvailable;
+ int ControllerNumber;
for (ControllerNumber = 0;
ControllerNumber < DAC960_ControllerCount;
ControllerNumber++)
break;
}
}
- BytesAvailable = strlen(StatusMessage) - Offset;
- if (Count >= BytesAvailable)
- {
- Count = BytesAvailable;
- *EOF = true;
- }
- if (Count <= 0) return 0;
- *Start = Page;
- memcpy(Page, &StatusMessage[Offset], Count);
- return Count;
+ seq_puts(m, StatusMessage);
+ return 0;
}
+static int dac960_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, dac960_proc_show, NULL);
+}
-/*
- DAC960_ProcReadInitialStatus implements reading /proc/rd/cN/initial_status.
-*/
+static const struct file_operations dac960_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = dac960_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
-static int DAC960_ProcReadInitialStatus(char *Page, char **Start, off_t Offset,
- int Count, int *EOF, void *Data)
+static int dac960_initial_status_proc_show(struct seq_file *m, void *v)
{
- DAC960_Controller_T *Controller = (DAC960_Controller_T *) Data;
- int BytesAvailable = Controller->InitialStatusLength - Offset;
- if (Count >= BytesAvailable)
- {
- Count = BytesAvailable;
- *EOF = true;
- }
- if (Count <= 0) return 0;
- *Start = Page;
- memcpy(Page, &Controller->CombinedStatusBuffer[Offset], Count);
- return Count;
+ DAC960_Controller_T *Controller = (DAC960_Controller_T *)m->private;
+ seq_printf(m, "%.*s", Controller->InitialStatusLength, Controller->CombinedStatusBuffer);
+ return 0;
}
+static int dac960_initial_status_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, dac960_initial_status_proc_show, PDE(inode)->data);
+}
-/*
- DAC960_ProcReadCurrentStatus implements reading /proc/rd/cN/current_status.
-*/
+static const struct file_operations dac960_initial_status_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = dac960_initial_status_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
-static int DAC960_ProcReadCurrentStatus(char *Page, char **Start, off_t Offset,
- int Count, int *EOF, void *Data)
+static int dac960_current_status_proc_show(struct seq_file *m, void *v)
{
- DAC960_Controller_T *Controller = (DAC960_Controller_T *) Data;
+ DAC960_Controller_T *Controller = (DAC960_Controller_T *) m->private;
unsigned char *StatusMessage =
"No Rebuild or Consistency Check in Progress\n";
int ProgressMessageLength = strlen(StatusMessage);
- int BytesAvailable;
if (jiffies != Controller->LastCurrentStatusTime)
{
Controller->CurrentStatusLength = 0;
}
Controller->LastCurrentStatusTime = jiffies;
}
- BytesAvailable = Controller->CurrentStatusLength - Offset;
- if (Count >= BytesAvailable)
- {
- Count = BytesAvailable;
- *EOF = true;
- }
- if (Count <= 0) return 0;
- *Start = Page;
- memcpy(Page, &Controller->CurrentStatusBuffer[Offset], Count);
- return Count;
+ seq_printf(m, "%.*s", Controller->CurrentStatusLength, Controller->CurrentStatusBuffer);
+ return 0;
}
+static int dac960_current_status_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, dac960_current_status_proc_show, PDE(inode)->data);
+}
-/*
- DAC960_ProcReadUserCommand implements reading /proc/rd/cN/user_command.
-*/
+static const struct file_operations dac960_current_status_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = dac960_current_status_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
-static int DAC960_ProcReadUserCommand(char *Page, char **Start, off_t Offset,
- int Count, int *EOF, void *Data)
+static int dac960_user_command_proc_show(struct seq_file *m, void *v)
{
- DAC960_Controller_T *Controller = (DAC960_Controller_T *) Data;
- int BytesAvailable = Controller->UserStatusLength - Offset;
- if (Count >= BytesAvailable)
- {
- Count = BytesAvailable;
- *EOF = true;
- }
- if (Count <= 0) return 0;
- *Start = Page;
- memcpy(Page, &Controller->UserStatusBuffer[Offset], Count);
- return Count;
-}
+ DAC960_Controller_T *Controller = (DAC960_Controller_T *)m->private;
+ seq_printf(m, "%.*s", Controller->UserStatusLength, Controller->UserStatusBuffer);
+ return 0;
+}
-/*
- DAC960_ProcWriteUserCommand implements writing /proc/rd/cN/user_command.
-*/
+static int dac960_user_command_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, dac960_user_command_proc_show, PDE(inode)->data);
+}
-static int DAC960_ProcWriteUserCommand(struct file *file,
+static ssize_t dac960_user_command_proc_write(struct file *file,
const char __user *Buffer,
- unsigned long Count, void *Data)
+ size_t Count, loff_t *pos)
{
- DAC960_Controller_T *Controller = (DAC960_Controller_T *) Data;
+ DAC960_Controller_T *Controller = (DAC960_Controller_T *) PDE(file->f_path.dentry->d_inode)->data;
unsigned char CommandBuffer[80];
int Length;
if (Count > sizeof(CommandBuffer)-1) return -EINVAL;
? Count : -EBUSY);
}
+static const struct file_operations dac960_user_command_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = dac960_user_command_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+ .write = dac960_user_command_proc_write,
+};
/*
DAC960_CreateProcEntries creates the /proc/rd/... entries for the
if (DAC960_ProcDirectoryEntry == NULL) {
DAC960_ProcDirectoryEntry = proc_mkdir("rd", NULL);
- StatusProcEntry = create_proc_read_entry("status", 0,
+ StatusProcEntry = proc_create("status", 0,
DAC960_ProcDirectoryEntry,
- DAC960_ProcReadStatus, NULL);
+ &dac960_proc_fops);
}
sprintf(Controller->ControllerName, "c%d", Controller->ControllerNumber);
ControllerProcEntry = proc_mkdir(Controller->ControllerName,
DAC960_ProcDirectoryEntry);
- create_proc_read_entry("initial_status", 0, ControllerProcEntry,
- DAC960_ProcReadInitialStatus, Controller);
- create_proc_read_entry("current_status", 0, ControllerProcEntry,
- DAC960_ProcReadCurrentStatus, Controller);
- UserCommandProcEntry =
- create_proc_read_entry("user_command", S_IWUSR | S_IRUSR,
- ControllerProcEntry, DAC960_ProcReadUserCommand,
- Controller);
- UserCommandProcEntry->write_proc = DAC960_ProcWriteUserCommand;
+ proc_create_data("initial_status", 0, ControllerProcEntry, &dac960_initial_status_proc_fops, Controller);
+ proc_create_data("current_status", 0, ControllerProcEntry, &dac960_current_status_proc_fops, Controller);
+ UserCommandProcEntry = proc_create_data("user_command", S_IWUSR | S_IRUSR, ControllerProcEntry, &dac960_user_command_proc_fops, Controller);
Controller->ControllerProcEntry = ControllerProcEntry;
}
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <linux/init.h>
+#include <linux/jiffies.h>
#include <linux/hdreg.h>
#include <linux/spinlock.h>
#include <linux/compat.h>
+#include <linux/mutex.h>
#include <asm/uaccess.h>
#include <asm/io.h>
static ctlr_info_t *hba[MAX_CTLR];
+static struct task_struct *cciss_scan_thread;
+static DEFINE_MUTEX(scan_mutex);
+static LIST_HEAD(scan_q);
+
static void do_cciss_request(struct request_queue *q);
static irqreturn_t do_cciss_intr(int irq, void *dev_id);
static int cciss_open(struct block_device *bdev, fmode_t mode);
static int cciss_getgeo(struct block_device *bdev, struct hd_geometry *geo);
static int cciss_revalidate(struct gendisk *disk);
-static int rebuild_lun_table(ctlr_info_t *h, int first_time);
+static int rebuild_lun_table(ctlr_info_t *h, int first_time, int via_ioctl);
static int deregister_disk(ctlr_info_t *h, int drv_index,
- int clear_all);
+ int clear_all, int via_ioctl);
static void cciss_read_capacity(int ctlr, int logvol, int withirq,
sector_t *total_size, unsigned int *block_size);
static int process_sendcmd_error(ctlr_info_t *h, CommandList_struct *c);
static void fail_all_cmds(unsigned long ctlr);
+static int add_to_scan_list(struct ctlr_info *h);
static int scan_thread(void *data);
static int check_for_unit_attention(ctlr_info_t *h, CommandList_struct *c);
+static void cciss_hba_release(struct device *dev);
+static void cciss_device_release(struct device *dev);
+static void cciss_free_gendisk(ctlr_info_t *h, int drv_index);
+static void cciss_free_drive_info(ctlr_info_t *h, int drv_index);
#ifdef CONFIG_PROC_FS
static void cciss_procinit(int i);
#include "cciss_scsi.c" /* For SCSI tape support */
-#define RAID_UNKNOWN 6
+static const char *raid_label[] = { "0", "4", "1(1+0)", "5", "5+1", "ADG",
+ "UNKNOWN"
+};
+#define RAID_UNKNOWN (sizeof(raid_label) / sizeof(raid_label[0])-1)
#ifdef CONFIG_PROC_FS
#define ENG_GIG 1000000000
#define ENG_GIG_FACTOR (ENG_GIG/512)
#define ENGAGE_SCSI "engage scsi"
-static const char *raid_label[] = { "0", "4", "1(1+0)", "5", "5+1", "ADG",
- "UNKNOWN"
-};
static struct proc_dir_entry *proc_cciss;
ctlr_info_t *h = seq->private;
unsigned ctlr = h->ctlr;
loff_t *pos = v;
- drive_info_struct *drv = &h->drv[*pos];
+ drive_info_struct *drv = h->drv[*pos];
if (*pos > h->highest_lun)
return 0;
vol_sz_frac *= 100;
sector_div(vol_sz_frac, ENG_GIG_FACTOR);
- if (drv->raid_level > 5)
+ if (drv->raid_level < 0 || drv->raid_level > RAID_UNKNOWN)
drv->raid_level = RAID_UNKNOWN;
seq_printf(seq, "cciss/c%dd%d:"
"\t%4u.%02uGB\tRAID %s\n",
return err;
}
-static struct file_operations cciss_proc_fops = {
+static const struct file_operations cciss_proc_fops = {
.owner = THIS_MODULE,
.open = cciss_seq_open,
.read = seq_read,
#define to_hba(n) container_of(n, struct ctlr_info, dev)
#define to_drv(n) container_of(n, drive_info_struct, dev)
-static struct device_type cciss_host_type = {
- .name = "cciss_host",
-};
+static ssize_t host_store_rescan(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct ctlr_info *h = to_hba(dev);
+
+ add_to_scan_list(h);
+ wake_up_process(cciss_scan_thread);
+ wait_for_completion_interruptible(&h->scan_wait);
+
+ return count;
+}
+DEVICE_ATTR(rescan, S_IWUSR, NULL, host_store_rescan);
static ssize_t dev_show_unique_id(struct device *dev,
struct device_attribute *attr,
}
DEVICE_ATTR(rev, S_IRUGO, dev_show_rev, NULL);
+static ssize_t cciss_show_lunid(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ drive_info_struct *drv = to_drv(dev);
+ struct ctlr_info *h = to_hba(drv->dev.parent);
+ unsigned long flags;
+ unsigned char lunid[8];
+
+ spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
+ if (h->busy_configuring) {
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return -EBUSY;
+ }
+ if (!drv->heads) {
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return -ENOTTY;
+ }
+ memcpy(lunid, drv->LunID, sizeof(lunid));
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return snprintf(buf, 20, "0x%02x%02x%02x%02x%02x%02x%02x%02x\n",
+ lunid[0], lunid[1], lunid[2], lunid[3],
+ lunid[4], lunid[5], lunid[6], lunid[7]);
+}
+DEVICE_ATTR(lunid, S_IRUGO, cciss_show_lunid, NULL);
+
+static ssize_t cciss_show_raid_level(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ drive_info_struct *drv = to_drv(dev);
+ struct ctlr_info *h = to_hba(drv->dev.parent);
+ int raid;
+ unsigned long flags;
+
+ spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
+ if (h->busy_configuring) {
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return -EBUSY;
+ }
+ raid = drv->raid_level;
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ if (raid < 0 || raid > RAID_UNKNOWN)
+ raid = RAID_UNKNOWN;
+
+ return snprintf(buf, strlen(raid_label[raid]) + 7, "RAID %s\n",
+ raid_label[raid]);
+}
+DEVICE_ATTR(raid_level, S_IRUGO, cciss_show_raid_level, NULL);
+
+static ssize_t cciss_show_usage_count(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ drive_info_struct *drv = to_drv(dev);
+ struct ctlr_info *h = to_hba(drv->dev.parent);
+ unsigned long flags;
+ int count;
+
+ spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
+ if (h->busy_configuring) {
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return -EBUSY;
+ }
+ count = drv->usage_count;
+ spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
+ return snprintf(buf, 20, "%d\n", count);
+}
+DEVICE_ATTR(usage_count, S_IRUGO, cciss_show_usage_count, NULL);
+
+static struct attribute *cciss_host_attrs[] = {
+ &dev_attr_rescan.attr,
+ NULL
+};
+
+static struct attribute_group cciss_host_attr_group = {
+ .attrs = cciss_host_attrs,
+};
+
+static const struct attribute_group *cciss_host_attr_groups[] = {
+ &cciss_host_attr_group,
+ NULL
+};
+
+static struct device_type cciss_host_type = {
+ .name = "cciss_host",
+ .groups = cciss_host_attr_groups,
+ .release = cciss_hba_release,
+};
+
static struct attribute *cciss_dev_attrs[] = {
&dev_attr_unique_id.attr,
&dev_attr_model.attr,
&dev_attr_vendor.attr,
&dev_attr_rev.attr,
+ &dev_attr_lunid.attr,
+ &dev_attr_raid_level.attr,
+ &dev_attr_usage_count.attr,
NULL
};
static struct device_type cciss_dev_type = {
.name = "cciss_device",
.groups = cciss_dev_attr_groups,
+ .release = cciss_device_release,
};
static struct bus_type cciss_bus_type = {
.name = "cciss",
};
+/*
+ * cciss_hba_release is called when the reference count
+ * of h->dev goes to zero.
+ */
+static void cciss_hba_release(struct device *dev)
+{
+ /*
+ * nothing to do, but need this to avoid a warning
+ * about not having a release handler from lib/kref.c.
+ */
+}
/*
* Initialize sysfs entry for each controller. This sets up and registers
static void cciss_destroy_hba_sysfs_entry(struct ctlr_info *h)
{
device_del(&h->dev);
+ put_device(&h->dev); /* final put. */
+}
+
+/* cciss_device_release is called when the reference count
+ * of h->drv[x]dev goes to zero.
+ */
+static void cciss_device_release(struct device *dev)
+{
+ drive_info_struct *drv = to_drv(dev);
+ kfree(drv);
}
/*
* /sys/bus/pci/devices/<dev/ccis#/. We also create a link from
* /sys/block/cciss!c#d# to this entry.
*/
-static int cciss_create_ld_sysfs_entry(struct ctlr_info *h,
- drive_info_struct *drv,
+static long cciss_create_ld_sysfs_entry(struct ctlr_info *h,
int drv_index)
{
- device_initialize(&drv->dev);
- drv->dev.type = &cciss_dev_type;
- drv->dev.bus = &cciss_bus_type;
- dev_set_name(&drv->dev, "c%dd%d", h->ctlr, drv_index);
- drv->dev.parent = &h->dev;
- return device_add(&drv->dev);
+ struct device *dev;
+
+ if (h->drv[drv_index]->device_initialized)
+ return 0;
+
+ dev = &h->drv[drv_index]->dev;
+ device_initialize(dev);
+ dev->type = &cciss_dev_type;
+ dev->bus = &cciss_bus_type;
+ dev_set_name(dev, "c%dd%d", h->ctlr, drv_index);
+ dev->parent = &h->dev;
+ h->drv[drv_index]->device_initialized = 1;
+ return device_add(dev);
}
/*
* Remove sysfs entries for a logical drive.
*/
-static void cciss_destroy_ld_sysfs_entry(drive_info_struct *drv)
+static void cciss_destroy_ld_sysfs_entry(struct ctlr_info *h, int drv_index,
+ int ctlr_exiting)
{
- device_del(&drv->dev);
+ struct device *dev = &h->drv[drv_index]->dev;
+
+ /* special case for c*d0, we only destroy it on controller exit */
+ if (drv_index == 0 && !ctlr_exiting)
+ return;
+
+ device_del(dev);
+ put_device(dev); /* the "final" put. */
+ h->drv[drv_index] = NULL;
}
/*
printk(KERN_DEBUG "cciss_open %s\n", bdev->bd_disk->disk_name);
#endif /* CCISS_DEBUG */
- if (host->busy_initializing || drv->busy_configuring)
+ if (drv->busy_configuring)
return -EBUSY;
/*
* Root is allowed to open raw volume zero even if it's not configured
if (MINOR(bdev->bd_dev) & 0x0f) {
return -ENXIO;
/* if it is, make sure we have a LUN ID */
- } else if (drv->LunID == 0) {
+ } else if (memcmp(drv->LunID, CTLR_LUNID,
+ sizeof(drv->LunID))) {
return -ENXIO;
}
}
case CCISS_DEREGDISK:
case CCISS_REGNEWD:
case CCISS_REVALIDVOLS:
- return rebuild_lun_table(host, 0);
+ return rebuild_lun_table(host, 0, 1);
case CCISS_GETLUNINFO:{
LogvolInfo_struct luninfo;
- luninfo.LunID = drv->LunID;
+ memcpy(&luninfo.LunID, drv->LunID,
+ sizeof(luninfo.LunID));
luninfo.num_opens = drv->usage_count;
luninfo.num_parts = 0;
if (copy_to_user(argp, &luninfo,
/* make sure the disk has been added and the drive is real
* because this can be called from the middle of init_one.
*/
- if (!(h->drv[curr_queue].queue) || !(h->drv[curr_queue].heads))
+ if (!h->drv[curr_queue])
+ continue;
+ if (!(h->drv[curr_queue]->queue) ||
+ !(h->drv[curr_queue]->heads))
continue;
blk_start_queue(h->gendisk[curr_queue]->queue);
spin_unlock_irqrestore(&h->lock, flags);
}
-static void log_unit_to_scsi3addr(ctlr_info_t *h, unsigned char scsi3addr[],
- uint32_t log_unit)
+static inline void log_unit_to_scsi3addr(ctlr_info_t *h,
+ unsigned char scsi3addr[], uint32_t log_unit)
{
- log_unit = h->drv[log_unit].LunID & 0x03fff;
- memset(&scsi3addr[4], 0, 4);
- memcpy(&scsi3addr[0], &log_unit, 4);
- scsi3addr[3] |= 0x40;
+ memcpy(scsi3addr, h->drv[log_unit]->LunID,
+ sizeof(h->drv[log_unit]->LunID));
}
/* This function gets the SCSI vendor, model, and revision of a logical drive
return;
}
-static void cciss_add_disk(ctlr_info_t *h, struct gendisk *disk,
+/*
+ * cciss_add_disk sets up the block device queue for a logical drive
+ */
+static int cciss_add_disk(ctlr_info_t *h, struct gendisk *disk,
int drv_index)
{
disk->queue = blk_init_queue(do_cciss_request, &h->lock);
+ if (!disk->queue)
+ goto init_queue_failure;
sprintf(disk->disk_name, "cciss/c%dd%d", h->ctlr, drv_index);
disk->major = h->major;
disk->first_minor = drv_index << NWD_SHIFT;
disk->fops = &cciss_fops;
- disk->private_data = &h->drv[drv_index];
- disk->driverfs_dev = &h->drv[drv_index].dev;
+ if (cciss_create_ld_sysfs_entry(h, drv_index))
+ goto cleanup_queue;
+ disk->private_data = h->drv[drv_index];
+ disk->driverfs_dev = &h->drv[drv_index]->dev;
/* Set up queue information */
blk_queue_bounce_limit(disk->queue, h->pdev->dma_mask);
disk->queue->queuedata = h;
blk_queue_logical_block_size(disk->queue,
- h->drv[drv_index].block_size);
+ h->drv[drv_index]->block_size);
/* Make sure all queue data is written out before */
- /* setting h->drv[drv_index].queue, as setting this */
+ /* setting h->drv[drv_index]->queue, as setting this */
/* allows the interrupt handler to start the queue */
wmb();
- h->drv[drv_index].queue = disk->queue;
+ h->drv[drv_index]->queue = disk->queue;
add_disk(disk);
+ return 0;
+
+cleanup_queue:
+ blk_cleanup_queue(disk->queue);
+ disk->queue = NULL;
+init_queue_failure:
+ return -1;
}
/* This function will check the usage_count of the drive to be updated/added.
* is also the controller node. Any changes to disk 0 will show up on
* the next reboot.
*/
-static void cciss_update_drive_info(int ctlr, int drv_index, int first_time)
+static void cciss_update_drive_info(int ctlr, int drv_index, int first_time,
+ int via_ioctl)
{
ctlr_info_t *h = hba[ctlr];
struct gendisk *disk;
unsigned long flags = 0;
int ret = 0;
drive_info_struct *drvinfo;
- int was_only_controller_node;
/* Get information about the disk and modify the driver structure */
inq_buff = kmalloc(sizeof(InquiryData_struct), GFP_KERNEL);
- drvinfo = kmalloc(sizeof(*drvinfo), GFP_KERNEL);
+ drvinfo = kzalloc(sizeof(*drvinfo), GFP_KERNEL);
if (inq_buff == NULL || drvinfo == NULL)
goto mem_msg;
- /* See if we're trying to update the "controller node"
- * this will happen the when the first logical drive gets
- * created by ACU.
- */
- was_only_controller_node = (drv_index == 0 &&
- h->drv[0].raid_level == -1);
-
/* testing to see if 16-byte CDBs are already being used */
if (h->cciss_read == CCISS_READ_16) {
cciss_read_capacity_16(h->ctlr, drv_index, 1,
drvinfo->model, drvinfo->rev);
cciss_get_serial_no(ctlr, drv_index, 1, drvinfo->serial_no,
sizeof(drvinfo->serial_no));
+ /* Save the lunid in case we deregister the disk, below. */
+ memcpy(drvinfo->LunID, h->drv[drv_index]->LunID,
+ sizeof(drvinfo->LunID));
/* Is it the same disk we already know, and nothing's changed? */
- if (h->drv[drv_index].raid_level != -1 &&
+ if (h->drv[drv_index]->raid_level != -1 &&
((memcmp(drvinfo->serial_no,
- h->drv[drv_index].serial_no, 16) == 0) &&
- drvinfo->block_size == h->drv[drv_index].block_size &&
- drvinfo->nr_blocks == h->drv[drv_index].nr_blocks &&
- drvinfo->heads == h->drv[drv_index].heads &&
- drvinfo->sectors == h->drv[drv_index].sectors &&
- drvinfo->cylinders == h->drv[drv_index].cylinders))
+ h->drv[drv_index]->serial_no, 16) == 0) &&
+ drvinfo->block_size == h->drv[drv_index]->block_size &&
+ drvinfo->nr_blocks == h->drv[drv_index]->nr_blocks &&
+ drvinfo->heads == h->drv[drv_index]->heads &&
+ drvinfo->sectors == h->drv[drv_index]->sectors &&
+ drvinfo->cylinders == h->drv[drv_index]->cylinders))
/* The disk is unchanged, nothing to update */
goto freeret;
* If the disk already exists then deregister it before proceeding
* (unless it's the first disk (for the controller node).
*/
- if (h->drv[drv_index].raid_level != -1 && drv_index != 0) {
+ if (h->drv[drv_index]->raid_level != -1 && drv_index != 0) {
printk(KERN_WARNING "disk %d has changed.\n", drv_index);
spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
- h->drv[drv_index].busy_configuring = 1;
+ h->drv[drv_index]->busy_configuring = 1;
spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
- /* deregister_disk sets h->drv[drv_index].queue = NULL
+ /* deregister_disk sets h->drv[drv_index]->queue = NULL
* which keeps the interrupt handler from starting
* the queue.
*/
- ret = deregister_disk(h, drv_index, 0);
- h->drv[drv_index].busy_configuring = 0;
+ ret = deregister_disk(h, drv_index, 0, via_ioctl);
}
/* If the disk is in use return */
goto freeret;
/* Save the new information from cciss_geometry_inquiry
- * and serial number inquiry.
+ * and serial number inquiry. If the disk was deregistered
+ * above, then h->drv[drv_index] will be NULL.
*/
- h->drv[drv_index].block_size = drvinfo->block_size;
- h->drv[drv_index].nr_blocks = drvinfo->nr_blocks;
- h->drv[drv_index].heads = drvinfo->heads;
- h->drv[drv_index].sectors = drvinfo->sectors;
- h->drv[drv_index].cylinders = drvinfo->cylinders;
- h->drv[drv_index].raid_level = drvinfo->raid_level;
- memcpy(h->drv[drv_index].serial_no, drvinfo->serial_no, 16);
- memcpy(h->drv[drv_index].vendor, drvinfo->vendor, VENDOR_LEN + 1);
- memcpy(h->drv[drv_index].model, drvinfo->model, MODEL_LEN + 1);
- memcpy(h->drv[drv_index].rev, drvinfo->rev, REV_LEN + 1);
+ if (h->drv[drv_index] == NULL) {
+ drvinfo->device_initialized = 0;
+ h->drv[drv_index] = drvinfo;
+ drvinfo = NULL; /* so it won't be freed below. */
+ } else {
+ /* special case for cxd0 */
+ h->drv[drv_index]->block_size = drvinfo->block_size;
+ h->drv[drv_index]->nr_blocks = drvinfo->nr_blocks;
+ h->drv[drv_index]->heads = drvinfo->heads;
+ h->drv[drv_index]->sectors = drvinfo->sectors;
+ h->drv[drv_index]->cylinders = drvinfo->cylinders;
+ h->drv[drv_index]->raid_level = drvinfo->raid_level;
+ memcpy(h->drv[drv_index]->serial_no, drvinfo->serial_no, 16);
+ memcpy(h->drv[drv_index]->vendor, drvinfo->vendor,
+ VENDOR_LEN + 1);
+ memcpy(h->drv[drv_index]->model, drvinfo->model, MODEL_LEN + 1);
+ memcpy(h->drv[drv_index]->rev, drvinfo->rev, REV_LEN + 1);
+ }
++h->num_luns;
disk = h->gendisk[drv_index];
- set_capacity(disk, h->drv[drv_index].nr_blocks);
+ set_capacity(disk, h->drv[drv_index]->nr_blocks);
/* If it's not disk 0 (drv_index != 0)
* or if it was disk 0, but there was previously
* (raid_leve == -1) then we want to update the
* logical drive's information.
*/
- if (drv_index || first_time)
- cciss_add_disk(h, disk, drv_index);
+ if (drv_index || first_time) {
+ if (cciss_add_disk(h, disk, drv_index) != 0) {
+ cciss_free_gendisk(h, drv_index);
+ cciss_free_drive_info(h, drv_index);
+ printk(KERN_WARNING "cciss:%d could not update "
+ "disk %d\n", h->ctlr, drv_index);
+ --h->num_luns;
+ }
+ }
freeret:
kfree(inq_buff);
}
/* This function will find the first index of the controllers drive array
- * that has a -1 for the raid_level and will return that index. This is
- * where new drives will be added. If the index to be returned is greater
- * than the highest_lun index for the controller then highest_lun is set
- * to this new index. If there are no available indexes then -1 is returned.
- * "controller_node" is used to know if this is a real logical drive, or just
- * the controller node, which determines if this counts towards highest_lun.
+ * that has a null drv pointer and allocate the drive info struct and
+ * will return that index This is where new drives will be added.
+ * If the index to be returned is greater than the highest_lun index for
+ * the controller then highest_lun is set * to this new index.
+ * If there are no available indexes or if tha allocation fails, then -1
+ * is returned. * "controller_node" is used to know if this is a real
+ * logical drive, or just the controller node, which determines if this
+ * counts towards highest_lun.
*/
-static int cciss_find_free_drive_index(int ctlr, int controller_node)
+static int cciss_alloc_drive_info(ctlr_info_t *h, int controller_node)
{
int i;
+ drive_info_struct *drv;
+ /* Search for an empty slot for our drive info */
for (i = 0; i < CISS_MAX_LUN; i++) {
- if (hba[ctlr]->drv[i].raid_level == -1) {
- if (i > hba[ctlr]->highest_lun)
- if (!controller_node)
- hba[ctlr]->highest_lun = i;
+
+ /* if not cxd0 case, and it's occupied, skip it. */
+ if (h->drv[i] && i != 0)
+ continue;
+ /*
+ * If it's cxd0 case, and drv is alloc'ed already, and a
+ * disk is configured there, skip it.
+ */
+ if (i == 0 && h->drv[i] && h->drv[i]->raid_level != -1)
+ continue;
+
+ /*
+ * We've found an empty slot. Update highest_lun
+ * provided this isn't just the fake cxd0 controller node.
+ */
+ if (i > h->highest_lun && !controller_node)
+ h->highest_lun = i;
+
+ /* If adding a real disk at cxd0, and it's already alloc'ed */
+ if (i == 0 && h->drv[i] != NULL)
return i;
- }
+
+ /*
+ * Found an empty slot, not already alloc'ed. Allocate it.
+ * Mark it with raid_level == -1, so we know it's new later on.
+ */
+ drv = kzalloc(sizeof(*drv), GFP_KERNEL);
+ if (!drv)
+ return -1;
+ drv->raid_level = -1; /* so we know it's new */
+ h->drv[i] = drv;
+ return i;
}
return -1;
}
+static void cciss_free_drive_info(ctlr_info_t *h, int drv_index)
+{
+ kfree(h->drv[drv_index]);
+ h->drv[drv_index] = NULL;
+}
+
+static void cciss_free_gendisk(ctlr_info_t *h, int drv_index)
+{
+ put_disk(h->gendisk[drv_index]);
+ h->gendisk[drv_index] = NULL;
+}
+
/* cciss_add_gendisk finds a free hba[]->drv structure
* and allocates a gendisk if needed, and sets the lunid
* in the drvinfo structure. It returns the index into
* a means to talk to the controller in case no logical
* drives have yet been configured.
*/
-static int cciss_add_gendisk(ctlr_info_t *h, __u32 lunid, int controller_node)
+static int cciss_add_gendisk(ctlr_info_t *h, unsigned char lunid[],
+ int controller_node)
{
int drv_index;
- drv_index = cciss_find_free_drive_index(h->ctlr, controller_node);
+ drv_index = cciss_alloc_drive_info(h, controller_node);
if (drv_index == -1)
return -1;
+
/*Check if the gendisk needs to be allocated */
if (!h->gendisk[drv_index]) {
h->gendisk[drv_index] =
printk(KERN_ERR "cciss%d: could not "
"allocate a new disk %d\n",
h->ctlr, drv_index);
- return -1;
+ goto err_free_drive_info;
}
}
- h->drv[drv_index].LunID = lunid;
- if (cciss_create_ld_sysfs_entry(h, &h->drv[drv_index], drv_index))
+ memcpy(h->drv[drv_index]->LunID, lunid,
+ sizeof(h->drv[drv_index]->LunID));
+ if (cciss_create_ld_sysfs_entry(h, drv_index))
goto err_free_disk;
-
/* Don't need to mark this busy because nobody */
/* else knows about this disk yet to contend */
/* for access to it. */
- h->drv[drv_index].busy_configuring = 0;
+ h->drv[drv_index]->busy_configuring = 0;
wmb();
return drv_index;
err_free_disk:
- put_disk(h->gendisk[drv_index]);
- h->gendisk[drv_index] = NULL;
+ cciss_free_gendisk(h, drv_index);
+err_free_drive_info:
+ cciss_free_drive_info(h, drv_index);
return -1;
}
if (h->gendisk[0] != NULL) /* already did this? Then bail. */
return;
- drv_index = cciss_add_gendisk(h, 0, 1);
- if (drv_index == -1) {
- printk(KERN_WARNING "cciss%d: could not "
- "add disk 0.\n", h->ctlr);
- return;
- }
- h->drv[drv_index].block_size = 512;
- h->drv[drv_index].nr_blocks = 0;
- h->drv[drv_index].heads = 0;
- h->drv[drv_index].sectors = 0;
- h->drv[drv_index].cylinders = 0;
- h->drv[drv_index].raid_level = -1;
- memset(h->drv[drv_index].serial_no, 0, 16);
+ drv_index = cciss_add_gendisk(h, CTLR_LUNID, 1);
+ if (drv_index == -1)
+ goto error;
+ h->drv[drv_index]->block_size = 512;
+ h->drv[drv_index]->nr_blocks = 0;
+ h->drv[drv_index]->heads = 0;
+ h->drv[drv_index]->sectors = 0;
+ h->drv[drv_index]->cylinders = 0;
+ h->drv[drv_index]->raid_level = -1;
+ memset(h->drv[drv_index]->serial_no, 0, 16);
disk = h->gendisk[drv_index];
- cciss_add_disk(h, disk, drv_index);
+ if (cciss_add_disk(h, disk, drv_index) == 0)
+ return;
+ cciss_free_gendisk(h, drv_index);
+ cciss_free_drive_info(h, drv_index);
+error:
+ printk(KERN_WARNING "cciss%d: could not "
+ "add disk 0.\n", h->ctlr);
+ return;
}
/* This function will add and remove logical drives from the Logical
* INPUT
* h = The controller to perform the operations on
*/
-static int rebuild_lun_table(ctlr_info_t *h, int first_time)
+static int rebuild_lun_table(ctlr_info_t *h, int first_time,
+ int via_ioctl)
{
int ctlr = h->ctlr;
int num_luns;
int i;
int drv_found;
int drv_index = 0;
- __u32 lunid = 0;
+ unsigned char lunid[8] = CTLR_LUNID;
unsigned long flags;
if (!capable(CAP_SYS_RAWIO))
drv_found = 0;
/* skip holes in the array from already deleted drives */
- if (h->drv[i].raid_level == -1)
+ if (h->drv[i] == NULL)
continue;
for (j = 0; j < num_luns; j++) {
- memcpy(&lunid, &ld_buff->LUN[j][0], 4);
- lunid = le32_to_cpu(lunid);
- if (h->drv[i].LunID == lunid) {
+ memcpy(lunid, &ld_buff->LUN[j][0], sizeof(lunid));
+ if (memcmp(h->drv[i]->LunID, lunid,
+ sizeof(lunid)) == 0) {
drv_found = 1;
break;
}
if (!drv_found) {
/* Deregister it from the OS, it's gone. */
spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
- h->drv[i].busy_configuring = 1;
+ h->drv[i]->busy_configuring = 1;
spin_unlock_irqrestore(CCISS_LOCK(h->ctlr), flags);
- return_code = deregister_disk(h, i, 1);
- cciss_destroy_ld_sysfs_entry(&h->drv[i]);
- h->drv[i].busy_configuring = 0;
+ return_code = deregister_disk(h, i, 1, via_ioctl);
+ if (h->drv[i] != NULL)
+ h->drv[i]->busy_configuring = 0;
}
}
drv_found = 0;
- memcpy(&lunid, &ld_buff->LUN[i][0], 4);
- lunid = le32_to_cpu(lunid);
-
+ memcpy(lunid, &ld_buff->LUN[i][0], sizeof(lunid));
/* Find if the LUN is already in the drive array
* of the driver. If so then update its info
* if not in use. If it does not exist then find
* the first free index and add it.
*/
for (j = 0; j <= h->highest_lun; j++) {
- if (h->drv[j].raid_level != -1 &&
- h->drv[j].LunID == lunid) {
+ if (h->drv[j] != NULL &&
+ memcmp(h->drv[j]->LunID, lunid,
+ sizeof(h->drv[j]->LunID)) == 0) {
drv_index = j;
drv_found = 1;
break;
if (drv_index == -1)
goto freeret;
}
- cciss_update_drive_info(ctlr, drv_index, first_time);
+ cciss_update_drive_info(ctlr, drv_index, first_time,
+ via_ioctl);
} /* end for */
freeret:
goto freeret;
}
+static void cciss_clear_drive_info(drive_info_struct *drive_info)
+{
+ /* zero out the disk size info */
+ drive_info->nr_blocks = 0;
+ drive_info->block_size = 0;
+ drive_info->heads = 0;
+ drive_info->sectors = 0;
+ drive_info->cylinders = 0;
+ drive_info->raid_level = -1;
+ memset(drive_info->serial_no, 0, sizeof(drive_info->serial_no));
+ memset(drive_info->model, 0, sizeof(drive_info->model));
+ memset(drive_info->rev, 0, sizeof(drive_info->rev));
+ memset(drive_info->vendor, 0, sizeof(drive_info->vendor));
+ /*
+ * don't clear the LUNID though, we need to remember which
+ * one this one is.
+ */
+}
+
/* This function will deregister the disk and it's queue from the
* kernel. It must be called with the controller lock held and the
* drv structures busy_configuring flag set. It's parameters are:
* the disk in preparation for re-adding it. In this case
* the highest_lun should be left unchanged and the LunID
* should not be cleared.
+ * via_ioctl
+ * This indicates whether we've reached this path via ioctl.
+ * This affects the maximum usage count allowed for c0d0 to be messed with.
+ * If this path is reached via ioctl(), then the max_usage_count will
+ * be 1, as the process calling ioctl() has got to have the device open.
+ * If we get here via sysfs, then the max usage count will be zero.
*/
static int deregister_disk(ctlr_info_t *h, int drv_index,
- int clear_all)
+ int clear_all, int via_ioctl)
{
int i;
struct gendisk *disk;
drive_info_struct *drv;
+ int recalculate_highest_lun;
if (!capable(CAP_SYS_RAWIO))
return -EPERM;
- drv = &h->drv[drv_index];
+ drv = h->drv[drv_index];
disk = h->gendisk[drv_index];
/* make sure logical volume is NOT is use */
if (clear_all || (h->gendisk[0] == disk)) {
- if (drv->usage_count > 1)
+ if (drv->usage_count > via_ioctl)
return -EBUSY;
} else if (drv->usage_count > 0)
return -EBUSY;
+ recalculate_highest_lun = (drv == h->drv[h->highest_lun]);
+
/* invalidate the devices and deregister the disk. If it is disk
* zero do not deregister it but just zero out it's values. This
* allows us to delete disk zero but keep the controller registered.
*/
if (h->gendisk[0] != disk) {
struct request_queue *q = disk->queue;
- if (disk->flags & GENHD_FL_UP)
+ if (disk->flags & GENHD_FL_UP) {
+ cciss_destroy_ld_sysfs_entry(h, drv_index, 0);
del_gendisk(disk);
- if (q) {
- blk_cleanup_queue(q);
- /* Set drv->queue to NULL so that we do not try
- * to call blk_start_queue on this queue in the
- * interrupt handler
- */
- drv->queue = NULL;
}
+ if (q)
+ blk_cleanup_queue(q);
/* If clear_all is set then we are deleting the logical
* drive, not just refreshing its info. For drives
* other than disk 0 we will call put_disk. We do not
}
} else {
set_capacity(disk, 0);
+ cciss_clear_drive_info(drv);
}
--h->num_luns;
- /* zero out the disk size info */
- drv->nr_blocks = 0;
- drv->block_size = 0;
- drv->heads = 0;
- drv->sectors = 0;
- drv->cylinders = 0;
- drv->raid_level = -1; /* This can be used as a flag variable to
- * indicate that this element of the drive
- * array is free.
- */
-
- if (clear_all) {
- /* check to see if it was the last disk */
- if (drv == h->drv + h->highest_lun) {
- /* if so, find the new hightest lun */
- int i, newhighest = -1;
- for (i = 0; i <= h->highest_lun; i++) {
- /* if the disk has size > 0, it is available */
- if (h->drv[i].heads)
- newhighest = i;
- }
- h->highest_lun = newhighest;
- }
- drv->LunID = 0;
+ /* if it was the last disk, find the new hightest lun */
+ if (clear_all && recalculate_highest_lun) {
+ int i, newhighest = -1;
+ for (i = 0; i <= h->highest_lun; i++) {
+ /* if the disk has size > 0, it is available */
+ if (h->drv[i] && h->drv[i]->heads)
+ newhighest = i;
+ }
+ h->highest_lun = newhighest;
}
return 0;
}
} else { /* Get geometry failed */
printk(KERN_WARNING "cciss: reading geometry failed\n");
}
- printk(KERN_INFO " heads=%d, sectors=%d, cylinders=%d\n\n",
- drv->heads, drv->sectors, drv->cylinders);
}
static void
*total_size = 0;
*block_size = BLOCK_SIZE;
}
- if (*total_size != 0)
- printk(KERN_INFO " blocks= %llu block_size= %d\n",
- (unsigned long long)*total_size+1, *block_size);
kfree(buf);
}
InquiryData_struct *inq_buff = NULL;
for (logvol = 0; logvol < CISS_MAX_LUN; logvol++) {
- if (h->drv[logvol].LunID == drv->LunID) {
+ if (memcmp(h->drv[logvol]->LunID, drv->LunID,
+ sizeof(drv->LunID)) == 0) {
FOUND = 1;
break;
}
/* The first 2 bits are reserved for controller error reporting. */
c->Header.Tag.lower = (c->cmdindex << 3);
c->Header.Tag.lower |= 0x04; /* flag for direct lookup. */
- c->Header.LUN.LogDev.VolId = drv->LunID;
- c->Header.LUN.LogDev.Mode = 1;
+ memcpy(&c->Header.LUN, drv->LunID, sizeof(drv->LunID));
c->Request.CDBLen = 10; // 12 byte commands not in FW yet;
c->Request.Type.Type = TYPE_CMD; // It is a command.
c->Request.Type.Attribute = ATTR_SIMPLE;
return IRQ_HANDLED;
}
+/**
+ * add_to_scan_list() - add controller to rescan queue
+ * @h: Pointer to the controller.
+ *
+ * Adds the controller to the rescan queue if not already on the queue.
+ *
+ * returns 1 if added to the queue, 0 if skipped (could be on the
+ * queue already, or the controller could be initializing or shutting
+ * down).
+ **/
+static int add_to_scan_list(struct ctlr_info *h)
+{
+ struct ctlr_info *test_h;
+ int found = 0;
+ int ret = 0;
+
+ if (h->busy_initializing)
+ return 0;
+
+ if (!mutex_trylock(&h->busy_shutting_down))
+ return 0;
+
+ mutex_lock(&scan_mutex);
+ list_for_each_entry(test_h, &scan_q, scan_list) {
+ if (test_h == h) {
+ found = 1;
+ break;
+ }
+ }
+ if (!found && !h->busy_scanning) {
+ INIT_COMPLETION(h->scan_wait);
+ list_add_tail(&h->scan_list, &scan_q);
+ ret = 1;
+ }
+ mutex_unlock(&scan_mutex);
+ mutex_unlock(&h->busy_shutting_down);
+
+ return ret;
+}
+
+/**
+ * remove_from_scan_list() - remove controller from rescan queue
+ * @h: Pointer to the controller.
+ *
+ * Removes the controller from the rescan queue if present. Blocks if
+ * the controller is currently conducting a rescan.
+ **/
+static void remove_from_scan_list(struct ctlr_info *h)
+{
+ struct ctlr_info *test_h, *tmp_h;
+ int scanning = 0;
+
+ mutex_lock(&scan_mutex);
+ list_for_each_entry_safe(test_h, tmp_h, &scan_q, scan_list) {
+ if (test_h == h) {
+ list_del(&h->scan_list);
+ complete_all(&h->scan_wait);
+ mutex_unlock(&scan_mutex);
+ return;
+ }
+ }
+ if (&h->busy_scanning)
+ scanning = 0;
+ mutex_unlock(&scan_mutex);
+
+ if (scanning)
+ wait_for_completion(&h->scan_wait);
+}
+
+/**
+ * scan_thread() - kernel thread used to rescan controllers
+ * @data: Ignored.
+ *
+ * A kernel thread used scan for drive topology changes on
+ * controllers. The thread processes only one controller at a time
+ * using a queue. Controllers are added to the queue using
+ * add_to_scan_list() and removed from the queue either after done
+ * processing or using remove_from_scan_list().
+ *
+ * returns 0.
+ **/
static int scan_thread(void *data)
{
- ctlr_info_t *h = data;
- int rc;
- DECLARE_COMPLETION_ONSTACK(wait);
- h->rescan_wait = &wait;
+ struct ctlr_info *h;
- for (;;) {
- rc = wait_for_completion_interruptible(&wait);
+ while (1) {
+ set_current_state(TASK_INTERRUPTIBLE);
+ schedule();
if (kthread_should_stop())
break;
- if (!rc)
- rebuild_lun_table(h, 0);
+
+ while (1) {
+ mutex_lock(&scan_mutex);
+ if (list_empty(&scan_q)) {
+ mutex_unlock(&scan_mutex);
+ break;
+ }
+
+ h = list_entry(scan_q.next,
+ struct ctlr_info,
+ scan_list);
+ list_del(&h->scan_list);
+ h->busy_scanning = 1;
+ mutex_unlock(&scan_mutex);
+
+ if (h) {
+ rebuild_lun_table(h, 0, 0);
+ complete_all(&h->scan_wait);
+ mutex_lock(&scan_mutex);
+ h->busy_scanning = 0;
+ mutex_unlock(&scan_mutex);
+ }
+ }
}
+
return 0;
}
case REPORT_LUNS_CHANGED:
printk(KERN_WARNING "cciss%d: report LUN data "
"changed\n", h->ctlr);
- if (h->rescan_wait)
- complete(h->rescan_wait);
+ add_to_scan_list(h);
+ wake_up_process(cciss_scan_thread);
return 1;
break;
case POWER_OR_RESET:
if (scratchpad == CCISS_FIRMWARE_READY)
break;
set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(HZ / 10); /* wait 100ms */
+ schedule_timeout(msecs_to_jiffies(100)); /* wait 100ms */
}
if (scratchpad != CCISS_FIRMWARE_READY) {
printk(KERN_WARNING "cciss: Board not ready. Timed out.\n");
break;
/* delay and try again */
set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(10);
+ schedule_timeout(msecs_to_jiffies(1));
}
#ifdef CCISS_DEBUG
return -1;
}
-static void free_hba(int i)
+static void free_hba(int n)
{
- ctlr_info_t *p = hba[i];
- int n;
+ ctlr_info_t *h = hba[n];
+ int i;
- hba[i] = NULL;
- for (n = 0; n < CISS_MAX_LUN; n++)
- put_disk(p->gendisk[n]);
- kfree(p);
+ hba[n] = NULL;
+ for (i = 0; i < h->highest_lun + 1; i++)
+ if (h->gendisk[i] != NULL)
+ put_disk(h->gendisk[i]);
+ kfree(h);
}
/* Send a message CDB to the firmware. */
hba[i]->busy_initializing = 1;
INIT_HLIST_HEAD(&hba[i]->cmpQ);
INIT_HLIST_HEAD(&hba[i]->reqQ);
+ mutex_init(&hba[i]->busy_shutting_down);
if (cciss_pci_init(hba[i], pdev) != 0)
goto clean0;
hba[i]->ctlr = i;
hba[i]->pdev = pdev;
+ init_completion(&hba[i]->scan_wait);
+
if (cciss_create_hba_sysfs_entry(hba[i]))
goto clean0;
hba[i]->num_luns = 0;
hba[i]->highest_lun = -1;
for (j = 0; j < CISS_MAX_LUN; j++) {
- hba[i]->drv[j].raid_level = -1;
- hba[i]->drv[j].queue = NULL;
+ hba[i]->drv[j] = NULL;
hba[i]->gendisk[j] = NULL;
}
hba[i]->cciss_max_sectors = 2048;
+ rebuild_lun_table(hba[i], 1, 0);
hba[i]->busy_initializing = 0;
-
- rebuild_lun_table(hba[i], 1);
- hba[i]->cciss_scan_thread = kthread_run(scan_thread, hba[i],
- "cciss_scan%02d", i);
- if (IS_ERR(hba[i]->cciss_scan_thread))
- return PTR_ERR(hba[i]->cciss_scan_thread);
-
return 1;
clean4:
cciss_destroy_hba_sysfs_entry(hba[i]);
clean0:
hba[i]->busy_initializing = 0;
- /* cleanup any queues that may have been initialized */
- for (j=0; j <= hba[i]->highest_lun; j++){
- drive_info_struct *drv = &(hba[i]->drv[j]);
- if (drv->queue)
- blk_cleanup_queue(drv->queue);
- }
+
/*
* Deliberately omit pci_disable_device(): it does something nasty to
* Smart Array controllers that pci_enable_device does not undo
return;
}
- kthread_stop(hba[i]->cciss_scan_thread);
+ mutex_lock(&hba[i]->busy_shutting_down);
+ remove_from_scan_list(hba[i]);
remove_proc_entry(hba[i]->devname, proc_cciss);
unregister_blkdev(hba[i]->major, hba[i]->devname);
if (disk) {
struct request_queue *q = disk->queue;
- if (disk->flags & GENHD_FL_UP)
+ if (disk->flags & GENHD_FL_UP) {
+ cciss_destroy_ld_sysfs_entry(hba[i], j, 1);
del_gendisk(disk);
+ }
if (q)
blk_cleanup_queue(q);
}
pci_release_regions(pdev);
pci_set_drvdata(pdev, NULL);
cciss_destroy_hba_sysfs_entry(hba[i]);
+ mutex_unlock(&hba[i]->busy_shutting_down);
free_hba(i);
}
if (err)
return err;
+ /* Start the scan thread */
+ cciss_scan_thread = kthread_run(scan_thread, NULL, "cciss_scan");
+ if (IS_ERR(cciss_scan_thread)) {
+ err = PTR_ERR(cciss_scan_thread);
+ goto err_bus_unregister;
+ }
+
/* Register for our PCI devices */
err = pci_register_driver(&cciss_pci_driver);
if (err)
- goto err_bus_register;
+ goto err_thread_stop;
- return 0;
+ return err;
-err_bus_register:
+err_thread_stop:
+ kthread_stop(cciss_scan_thread);
+err_bus_unregister:
bus_unregister(&cciss_bus_type);
+
return err;
}
cciss_remove_one(hba[i]->pdev);
}
}
+ kthread_stop(cciss_scan_thread);
remove_proc_entry("driver/cciss", NULL);
bus_unregister(&cciss_bus_type);
}
#define CCISS_H
#include <linux/genhd.h>
+#include <linux/mutex.h>
#include "cciss_cmd.h"
};
typedef struct _drive_info_struct
{
- __u32 LunID;
+ unsigned char LunID[8];
int usage_count;
struct request_queue *queue;
sector_t nr_blocks;
char vendor[VENDOR_LEN + 1]; /* SCSI vendor string */
char model[MODEL_LEN + 1]; /* SCSI model string */
char rev[REV_LEN + 1]; /* SCSI revision string */
+ char device_initialized; /* indicates whether dev is initialized */
} drive_info_struct;
struct ctlr_info
BYTE cciss_read_capacity;
// information about each logical volume
- drive_info_struct drv[CISS_MAX_LUN];
+ drive_info_struct *drv[CISS_MAX_LUN];
struct access_method access;
int nr_frees;
int busy_configuring;
int busy_initializing;
+ int busy_scanning;
+ struct mutex busy_shutting_down;
/* This element holds the zero based queue number of the last
* queue to be started. It is used for fairness.
/* and saved for later processing */
#endif
unsigned char alive;
- struct completion *rescan_wait;
- struct task_struct *cciss_scan_thread;
+ struct list_head scan_list;
+ struct completion scan_wait;
struct device dev;
};
#include <linux/blkpg.h>
#include <linux/timer.h>
#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
#include <linux/init.h>
#include <linux/hdreg.h>
#include <linux/spinlock.h>
#ifdef CONFIG_PROC_FS
static void ida_procinit(int i);
-static int ida_proc_get_info(char *buffer, char **start, off_t offset, int length, int *eof, void *data);
#else
static void ida_procinit(int i) {}
#endif
#ifdef CONFIG_PROC_FS
static struct proc_dir_entry *proc_array;
+static const struct file_operations ida_proc_fops;
/*
* Get us a file in /proc/array that says something about each controller.
if (!proc_array) return;
}
- create_proc_read_entry(hba[i]->devname, 0, proc_array,
- ida_proc_get_info, hba[i]);
+ proc_create_data(hba[i]->devname, 0, proc_array, &ida_proc_fops, hba[i]);
}
/*
* Report information about this controller.
*/
-static int ida_proc_get_info(char *buffer, char **start, off_t offset, int length, int *eof, void *data)
+static int ida_proc_show(struct seq_file *m, void *v)
{
- off_t pos = 0;
- off_t len = 0;
- int size, i, ctlr;
- ctlr_info_t *h = (ctlr_info_t*)data;
+ int i, ctlr;
+ ctlr_info_t *h = (ctlr_info_t*)m->private;
drv_info_t *drv;
#ifdef CPQ_PROC_PRINT_QUEUES
cmdlist_t *c;
#endif
ctlr = h->ctlr;
- size = sprintf(buffer, "%s: Compaq %s Controller\n"
+ seq_printf(m, "%s: Compaq %s Controller\n"
" Board ID: 0x%08lx\n"
" Firmware Revision: %c%c%c%c\n"
" Controller Sig: 0x%08lx\n"
h->log_drives, h->phys_drives,
h->Qdepth, h->maxQsinceinit);
- pos += size; len += size;
-
- size = sprintf(buffer+len, "Logical Drive Info:\n");
- pos += size; len += size;
+ seq_puts(m, "Logical Drive Info:\n");
for(i=0; i<h->log_drives; i++) {
drv = &h->drv[i];
- size = sprintf(buffer+len, "ida/c%dd%d: blksz=%d nr_blks=%d\n",
+ seq_printf(m, "ida/c%dd%d: blksz=%d nr_blks=%d\n",
ctlr, i, drv->blk_size, drv->nr_blks);
- pos += size; len += size;
}
#ifdef CPQ_PROC_PRINT_QUEUES
spin_lock_irqsave(IDA_LOCK(h->ctlr), flags);
- size = sprintf(buffer+len, "\nCurrent Queues:\n");
- pos += size; len += size;
+ seq_puts(m, "\nCurrent Queues:\n");
c = h->reqQ;
- size = sprintf(buffer+len, "reqQ = %p", c); pos += size; len += size;
+ seq_printf(m, "reqQ = %p", c);
if (c) c=c->next;
while(c && c != h->reqQ) {
- size = sprintf(buffer+len, "->%p", c);
- pos += size; len += size;
+ seq_printf(m, "->%p", c);
c=c->next;
}
c = h->cmpQ;
- size = sprintf(buffer+len, "\ncmpQ = %p", c); pos += size; len += size;
+ seq_printf(m, "\ncmpQ = %p", c);
if (c) c=c->next;
while(c && c != h->cmpQ) {
- size = sprintf(buffer+len, "->%p", c);
- pos += size; len += size;
+ seq_printf(m, "->%p", c);
c=c->next;
}
- size = sprintf(buffer+len, "\n"); pos += size; len += size;
+ seq_putc(m, '\n');
spin_unlock_irqrestore(IDA_LOCK(h->ctlr), flags);
#endif
- size = sprintf(buffer+len, "nr_allocs = %d\nnr_frees = %d\n",
+ seq_printf(m, "nr_allocs = %d\nnr_frees = %d\n",
h->nr_allocs, h->nr_frees);
- pos += size; len += size;
-
- *eof = 1;
- *start = buffer+offset;
- len -= offset;
- if (len>length)
- len = length;
- return len;
+ return 0;
+}
+
+static int ida_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, ida_proc_show, PDE(inode)->data);
}
+
+static const struct file_operations ida_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = ida_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
#endif /* CONFIG_PROC_FS */
module_param_array(eisa, int, NULL, 0);
return 0;
}
-static int cdrom_sysctl_info(ctl_table *ctl, int write, struct file * filp,
+static int cdrom_sysctl_info(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int pos;
goto done;
doit:
mutex_unlock(&cdrom_mutex);
- return proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ return proc_dostring(ctl, write, buffer, lenp, ppos);
done:
printk(KERN_INFO "cdrom: info buffer too small\n");
goto doit;
mutex_unlock(&cdrom_mutex);
}
-static int cdrom_sysctl_handler(ctl_table *ctl, int write, struct file * filp,
+static int cdrom_sysctl_handler(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int ret;
- ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
if (write) {
The mmtimer device allows direct userspace access to the
Altix system timer.
+config UV_MMTIMER
+ tristate "UV_MMTIMER Memory mapped RTC for SGI UV"
+ depends on X86_UV
+ default m
+ help
+ The uv_mmtimer device allows direct userspace access to the
+ UV system timer.
+
source "drivers/char/tpm/Kconfig"
config TELCLOCK
obj-$(CONFIG_SGI_SNSC) += snsc.o snsc_event.o
obj-$(CONFIG_MSPEC) += mspec.o
obj-$(CONFIG_MMTIMER) += mmtimer.o
+obj-$(CONFIG_UV_MMTIMER) += uv_mmtimer.o
obj-$(CONFIG_VIOTAPE) += viotape.o
obj-$(CONFIG_HVCS) += hvcs.o
obj-$(CONFIG_IBM_BSR) += bsr.o
struct agp_bridge_data {
const struct agp_version *version;
const struct agp_bridge_driver *driver;
- struct vm_operations_struct *vm_ops;
+ const struct vm_operations_struct *vm_ops;
void *previous_size;
void *current_size;
void *dev_private_data;
{ 0, 0, 0 }, /* filled in by alpha_core_agp_setup */
};
-struct vm_operations_struct alpha_core_agp_vm_ops = {
+static const struct vm_operations_struct alpha_core_agp_vm_ops = {
.fault = alpha_core_agp_vm_fault,
};
#define PCI_DEVICE_ID_INTEL_Q35_IG 0x29B2
#define PCI_DEVICE_ID_INTEL_Q33_HB 0x29D0
#define PCI_DEVICE_ID_INTEL_Q33_IG 0x29D2
+#define PCI_DEVICE_ID_INTEL_B43_HB 0x2E40
+#define PCI_DEVICE_ID_INTEL_B43_IG 0x2E42
#define PCI_DEVICE_ID_INTEL_GM45_HB 0x2A40
#define PCI_DEVICE_ID_INTEL_GM45_IG 0x2A42
#define PCI_DEVICE_ID_INTEL_IGD_E_HB 0x2E00
agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_G45_HB || \
agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_GM45_HB || \
agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_G41_HB || \
+ agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_B43_HB || \
agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_IGDNG_D_HB || \
agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_IGDNG_M_HB || \
agp_bridge->dev->device == PCI_DEVICE_ID_INTEL_IGDNG_MA_HB)
if (!intel_private.i8xx_page)
return;
- /* make page uncached */
- map_page_into_agp(intel_private.i8xx_page);
-
intel_private.i8xx_flush_page = kmap(intel_private.i8xx_page);
if (!intel_private.i8xx_flush_page)
intel_i830_fini_flush();
}
+static void
+do_wbinvd(void *null)
+{
+ wbinvd();
+}
+
+/* The chipset_flush interface needs to get data that has already been
+ * flushed out of the CPU all the way out to main memory, because the GPU
+ * doesn't snoop those buffers.
+ *
+ * The 8xx series doesn't have the same lovely interface for flushing the
+ * chipset write buffers that the later chips do. According to the 865
+ * specs, it's 64 octwords, or 1KB. So, to get those previous things in
+ * that buffer out, we just fill 1KB and clflush it out, on the assumption
+ * that it'll push whatever was in there out. It appears to work.
+ */
static void intel_i830_chipset_flush(struct agp_bridge_data *bridge)
{
unsigned int *pg = intel_private.i8xx_flush_page;
- int i;
- for (i = 0; i < 256; i += 2)
- *(pg + i) = i;
+ memset(pg, 0, 1024);
- wmb();
+ if (cpu_has_clflush) {
+ clflush_cache_range(pg, 1024);
+ } else {
+ if (on_each_cpu(do_wbinvd, NULL, 1) != 0)
+ printk(KERN_ERR "Timed out waiting for cache flush.\n");
+ }
}
/* The intel i830 automatically initializes the agp aperture during POST.
case PCI_DEVICE_ID_INTEL_Q45_HB:
case PCI_DEVICE_ID_INTEL_G45_HB:
case PCI_DEVICE_ID_INTEL_G41_HB:
+ case PCI_DEVICE_ID_INTEL_B43_HB:
case PCI_DEVICE_ID_INTEL_IGDNG_D_HB:
case PCI_DEVICE_ID_INTEL_IGDNG_M_HB:
case PCI_DEVICE_ID_INTEL_IGDNG_MA_HB:
"Q45/Q43", NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_G45_HB, PCI_DEVICE_ID_INTEL_G45_IG, 0,
"G45/G43", NULL, &intel_i965_driver },
+ { PCI_DEVICE_ID_INTEL_B43_HB, PCI_DEVICE_ID_INTEL_B43_IG, 0,
+ "B43", NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_G41_HB, PCI_DEVICE_ID_INTEL_G41_IG, 0,
"G41", NULL, &intel_i965_driver },
{ PCI_DEVICE_ID_INTEL_IGDNG_D_HB, PCI_DEVICE_ID_INTEL_IGDNG_D_IG, 0,
ID(PCI_DEVICE_ID_INTEL_Q45_HB),
ID(PCI_DEVICE_ID_INTEL_G45_HB),
ID(PCI_DEVICE_ID_INTEL_G41_HB),
+ ID(PCI_DEVICE_ID_INTEL_B43_HB),
ID(PCI_DEVICE_ID_INTEL_IGDNG_D_HB),
ID(PCI_DEVICE_ID_INTEL_IGDNG_M_HB),
ID(PCI_DEVICE_ID_INTEL_IGDNG_MA_HB),
return as ? 0 : -ENOMEM;
}
-static struct file_operations apm_bios_fops = {
+static const struct file_operations apm_bios_fops = {
.owner = THIS_MODULE,
.read = apm_read,
.poll = apm_poll,
/*
* Blackfin On-Chip OTP Memory Interface
- * Supports BF52x/BF54x
*
- * Copyright 2007-2008 Analog Devices Inc.
+ * Copyright 2007-2009 Analog Devices Inc.
*
* Enter bugs at http://blackfin.uclinux.org/
*
#include <linux/module.h>
#include <linux/mutex.h>
#include <linux/types.h>
+#include <mtd/mtd-abi.h>
#include <asm/blackfin.h>
+#include <asm/bfrom.h>
#include <asm/uaccess.h>
#define stamp(fmt, args...) pr_debug("%s:%i: " fmt "\n", __func__, __LINE__, ## args)
static DEFINE_MUTEX(bfin_otp_lock);
-/* OTP Boot ROM functions */
-#define _BOOTROM_OTP_COMMAND 0xEF000018
-#define _BOOTROM_OTP_READ 0xEF00001A
-#define _BOOTROM_OTP_WRITE 0xEF00001C
-
-static u32 (* const otp_command)(u32 command, u32 value) = (void *)_BOOTROM_OTP_COMMAND;
-static u32 (* const otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)_BOOTROM_OTP_READ;
-static u32 (* const otp_write)(u32 page, u32 flags, u64 *page_content) = (void *)_BOOTROM_OTP_WRITE;
-
-/* otp_command(): defines for "command" */
-#define OTP_INIT 0x00000001
-#define OTP_CLOSE 0x00000002
-
-/* otp_{read,write}(): defines for "flags" */
-#define OTP_LOWER_HALF 0x00000000 /* select upper/lower 64-bit half (bit 0) */
-#define OTP_UPPER_HALF 0x00000001
-#define OTP_NO_ECC 0x00000010 /* do not use ECC */
-#define OTP_LOCK 0x00000020 /* sets page protection bit for page */
-#define OTP_ACCESS_READ 0x00001000
-#define OTP_ACCESS_READWRITE 0x00002000
-
-/* Return values for all functions */
-#define OTP_SUCCESS 0x00000000
-#define OTP_MASTER_ERROR 0x001
-#define OTP_WRITE_ERROR 0x003
-#define OTP_READ_ERROR 0x005
-#define OTP_ACC_VIO_ERROR 0x009
-#define OTP_DATA_MULT_ERROR 0x011
-#define OTP_ECC_MULT_ERROR 0x021
-#define OTP_PREV_WR_ERROR 0x041
-#define OTP_DATA_SB_WARN 0x100
-#define OTP_ECC_SB_WARN 0x200
-
/**
* bfin_otp_read - Read OTP pages
*
page = *pos / (sizeof(u64) * 2);
while (bytes_done < count) {
flags = (*pos % (sizeof(u64) * 2) ? OTP_UPPER_HALF : OTP_LOWER_HALF);
- stamp("processing page %i (%s)", page, (flags == OTP_UPPER_HALF ? "upper" : "lower"));
- ret = otp_read(page, flags, &content);
+ stamp("processing page %i (0x%x:%s)", page, flags,
+ (flags & OTP_UPPER_HALF ? "upper" : "lower"));
+ ret = bfrom_OtpRead(page, flags, &content);
if (ret & OTP_MASTER_ERROR) {
+ stamp("error from otp: 0x%x", ret);
bytes_done = -EIO;
break;
}
bytes_done = -EFAULT;
break;
}
- if (flags == OTP_UPPER_HALF)
+ if (flags & OTP_UPPER_HALF)
++page;
bytes_done += sizeof(content);
*pos += sizeof(content);
}
#ifdef CONFIG_BFIN_OTP_WRITE_ENABLE
+static bool allow_writes;
+
+/**
+ * bfin_otp_init_timing - setup OTP timing parameters
+ *
+ * Required before doing any write operation. Algorithms from HRM.
+ */
+static u32 bfin_otp_init_timing(void)
+{
+ u32 tp1, tp2, tp3, timing;
+
+ tp1 = get_sclk() / 1000000;
+ tp2 = (2 * get_sclk() / 10000000) << 8;
+ tp3 = (0x1401) << 15;
+ timing = tp1 | tp2 | tp3;
+ if (bfrom_OtpCommand(OTP_INIT, timing))
+ return 0;
+
+ return timing;
+}
+
+/**
+ * bfin_otp_deinit_timing - set timings to only allow reads
+ *
+ * Should be called after all writes are done.
+ */
+static void bfin_otp_deinit_timing(u32 timing)
+{
+ /* mask bits [31:15] so that any attempts to write fail */
+ bfrom_OtpCommand(OTP_CLOSE, 0);
+ bfrom_OtpCommand(OTP_INIT, timing & ~(-1 << 15));
+ bfrom_OtpCommand(OTP_CLOSE, 0);
+}
+
/**
- * bfin_otp_write - Write OTP pages
+ * bfin_otp_write - write OTP pages
*
* All writes must be in half page chunks (half page == 64 bits).
*/
static ssize_t bfin_otp_write(struct file *filp, const char __user *buff, size_t count, loff_t *pos)
{
- stampit();
+ ssize_t bytes_done;
+ u32 timing, page, base_flags, flags, ret;
+ u64 content;
+
+ if (!allow_writes)
+ return -EACCES;
if (count % sizeof(u64))
return -EMSGSIZE;
if (mutex_lock_interruptible(&bfin_otp_lock))
return -ERESTARTSYS;
- /* need otp_init() documentation before this can be implemented */
+ stampit();
+
+ timing = bfin_otp_init_timing();
+ if (timing == 0) {
+ mutex_unlock(&bfin_otp_lock);
+ return -EIO;
+ }
+
+ base_flags = OTP_CHECK_FOR_PREV_WRITE;
+
+ bytes_done = 0;
+ page = *pos / (sizeof(u64) * 2);
+ while (bytes_done < count) {
+ flags = base_flags | (*pos % (sizeof(u64) * 2) ? OTP_UPPER_HALF : OTP_LOWER_HALF);
+ stamp("processing page %i (0x%x:%s) from %p", page, flags,
+ (flags & OTP_UPPER_HALF ? "upper" : "lower"), buff + bytes_done);
+ if (copy_from_user(&content, buff + bytes_done, sizeof(content))) {
+ bytes_done = -EFAULT;
+ break;
+ }
+ ret = bfrom_OtpWrite(page, flags, &content);
+ if (ret & OTP_MASTER_ERROR) {
+ stamp("error from otp: 0x%x", ret);
+ bytes_done = -EIO;
+ break;
+ }
+ if (flags & OTP_UPPER_HALF)
+ ++page;
+ bytes_done += sizeof(content);
+ *pos += sizeof(content);
+ }
+
+ bfin_otp_deinit_timing(timing);
mutex_unlock(&bfin_otp_lock);
+ return bytes_done;
+}
+
+static long bfin_otp_ioctl(struct file *filp, unsigned cmd, unsigned long arg)
+{
+ stampit();
+
+ switch (cmd) {
+ case OTPLOCK: {
+ u32 timing;
+ int ret = -EIO;
+
+ if (!allow_writes)
+ return -EACCES;
+
+ if (mutex_lock_interruptible(&bfin_otp_lock))
+ return -ERESTARTSYS;
+
+ timing = bfin_otp_init_timing();
+ if (timing) {
+ u32 otp_result = bfrom_OtpWrite(arg, OTP_LOCK, NULL);
+ stamp("locking page %lu resulted in 0x%x", arg, otp_result);
+ if (!(otp_result & OTP_MASTER_ERROR))
+ ret = 0;
+
+ bfin_otp_deinit_timing(timing);
+ }
+
+ mutex_unlock(&bfin_otp_lock);
+
+ return ret;
+ }
+
+ case MEMLOCK:
+ allow_writes = false;
+ return 0;
+
+ case MEMUNLOCK:
+ allow_writes = true;
+ return 0;
+ }
+
return -EINVAL;
}
#else
# define bfin_otp_write NULL
+# define bfin_otp_ioctl NULL
#endif
-static struct file_operations bfin_otp_fops = {
- .owner = THIS_MODULE,
- .read = bfin_otp_read,
- .write = bfin_otp_write,
+static const struct file_operations bfin_otp_fops = {
+ .owner = THIS_MODULE,
+ .unlocked_ioctl = bfin_otp_ioctl,
+ .read = bfin_otp_read,
+ .write = bfin_otp_write,
};
static struct miscdevice bfin_otp_misc_device = {
continue;
}
#ifdef MODULE
- if (isparam && irq[i])
+ if (isparam && i < NR_CARDS && irq[i])
cy_isa_irq = irq[i];
else
#endif
#include <linux/errno.h> /* for -EBUSY */
#include <linux/ioport.h> /* for request_region */
#include <linux/delay.h> /* for loops_per_jiffy */
+#include <linux/sched.h>
#include <linux/smp_lock.h> /* cycle_kernel_lock() */
#include <asm/io.h> /* for inb_p, outb_p, inb, outb, etc. */
#include <asm/uaccess.h> /* for get_user, etc. */
unsigned long m, t;
t = devp->hd_ireqfreq;
- m = read_counter(&devp->hd_hpet->hpet_mc);
- write_counter(t + m + devp->hd_hpets->hp_delta,
- &devp->hd_timer->hpet_compare);
+ m = read_counter(&devp->hd_timer->hpet_compare);
+ write_counter(t + m, &devp->hd_timer->hpet_compare);
}
if (devp->hd_flags & HPET_SHARED_IRQ)
g = v | Tn_32MODE_CNF_MASK | Tn_INT_ENB_CNF_MASK;
if (devp->hd_flags & HPET_PERIODIC) {
- write_counter(t, &timer->hpet_compare);
g |= Tn_TYPE_CNF_MASK;
- v |= Tn_TYPE_CNF_MASK;
- writeq(v, &timer->hpet_config);
- v |= Tn_VAL_SET_CNF_MASK;
+ v |= Tn_TYPE_CNF_MASK | Tn_VAL_SET_CNF_MASK;
writeq(v, &timer->hpet_config);
local_irq_save(flags);
- /* NOTE: what we modify here is a hidden accumulator
+ /*
+ * NOTE: First we modify the hidden accumulator
* register supported by periodic-capable comparators.
* We never want to modify the (single) counter; that
- * would affect all the comparators.
+ * would affect all the comparators. The value written
+ * is the counter value when the first interrupt is due.
*/
m = read_counter(&hpet->hpet_mc);
write_counter(t + m + hpetp->hp_delta, &timer->hpet_compare);
+ /*
+ * Then we modify the comparator, indicating the period
+ * for subsequent interrupt.
+ */
+ write_counter(t, &timer->hpet_compare);
} else {
local_irq_save(flags);
m = read_counter(&hpet->hpet_mc);
EXPORT_SYMBOL_GPL(hvc_poll);
/**
- * hvc_resize() - Update terminal window size information.
+ * __hvc_resize() - Update terminal window size information.
* @hp: HVC console pointer
* @ws: Terminal window size structure
*
*
* Locking: Locking free; the function MUST be called holding hp->lock
*/
-void hvc_resize(struct hvc_struct *hp, struct winsize ws)
+void __hvc_resize(struct hvc_struct *hp, struct winsize ws)
{
hp->ws = ws;
schedule_work(&hp->tty_resize);
}
-EXPORT_SYMBOL_GPL(hvc_resize);
+EXPORT_SYMBOL_GPL(__hvc_resize);
/*
* This kthread is either polling or interrupt driven. This is determined by
#define HVC_CONSOLE_H
#include <linux/kref.h>
#include <linux/tty.h>
+#include <linux/spinlock.h>
/*
* This is the max number of console adapters that can/will be found as
void hvc_kick(void);
/* Resize hvc tty terminal window */
-extern void hvc_resize(struct hvc_struct *hp, struct winsize ws);
+extern void __hvc_resize(struct hvc_struct *hp, struct winsize ws);
+
+static inline void hvc_resize(struct hvc_struct *hp, struct winsize ws)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&hp->lock, flags);
+ __hvc_resize(hp, ws);
+ spin_unlock_irqrestore(&hp->lock, flags);
+}
/* default notifier for irq based notification */
extern int notifier_add_irq(struct hvc_struct *hp, int data);
case MSG_TYPE_WINSIZE:
if (rb->mbuf->datalen != sizeof(struct winsize))
break;
- hvc_resize(priv->hvc, *((struct winsize *) rb->mbuf->data));
+ /* The caller must ensure that the hvc is locked, which
+ * is the case when called from hvc_iucv_get_chars() */
+ __hvc_resize(priv->hvc, *((struct winsize *) rb->mbuf->data));
break;
case MSG_TYPE_ERROR: /* ignored ... */
if (!res)
return -ENOENT;
- mem = request_mem_region(res->start, res->end - res->start + 1,
+ mem = request_mem_region(res->start, resource_size(res),
pdev->name);
if (mem == NULL) {
ret = -EBUSY;
}
dev_set_drvdata(&pdev->dev, mem);
- rng_base = ioremap(res->start, res->end - res->start + 1);
+ rng_base = ioremap(res->start, resource_size(res));
if (!rng_base) {
ret = -ENOMEM;
goto err_ioremap;
#include <linux/errno.h>
#include <asm/system.h>
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/slab.h>
#include <linux/ipmi.h>
#include <linux/errno.h>
#include <asm/system.h>
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
#include <linux/slab.h>
}
#endif
-static struct vm_operations_struct mmap_mem_ops = {
+static const struct vm_operations_struct mmap_mem_ops = {
#ifdef CONFIG_HAVE_IOREMAP_PROT
.access = generic_access_phys
#endif
if (chunk > PAGE_SIZE)
chunk = PAGE_SIZE; /* Just for latency reasons */
- unwritten = clear_user(buf, chunk);
+ unwritten = __clear_user(buf, chunk);
written += chunk - unwritten;
if (unwritten)
break;
return VM_FAULT_NOPAGE;
}
-static struct vm_operations_struct mspec_vm_ops = {
+static const struct vm_operations_struct mspec_vm_ops = {
.open = mspec_open,
.close = mspec_close,
.fault = mspec_fault,
case IOCTL_MW_REGISTER_IPC: {
unsigned int ipcnum = (unsigned int) ioarg;
- PRINTK_3(TRACE_MWAVE,
- "mwavedd::mwave_ioctl IOCTL_MW_REGISTER_IPC"
- " ipcnum %x entry usIntCount %x\n",
- ipcnum,
- pDrvData->IPCs[ipcnum].usIntCount);
-
if (ipcnum >= ARRAY_SIZE(pDrvData->IPCs)) {
PRINTK_ERROR(KERN_ERR_MWAVE
"mwavedd::mwave_ioctl:"
ipcnum);
return -EINVAL;
}
+ PRINTK_3(TRACE_MWAVE,
+ "mwavedd::mwave_ioctl IOCTL_MW_REGISTER_IPC"
+ " ipcnum %x entry usIntCount %x\n",
+ ipcnum,
+ pDrvData->IPCs[ipcnum].usIntCount);
+
lock_kernel();
pDrvData->IPCs[ipcnum].bIsHere = FALSE;
pDrvData->IPCs[ipcnum].bIsEnabled = TRUE;
case IOCTL_MW_GET_IPC: {
unsigned int ipcnum = (unsigned int) ioarg;
- PRINTK_3(TRACE_MWAVE,
- "mwavedd::mwave_ioctl IOCTL_MW_GET_IPC"
- " ipcnum %x, usIntCount %x\n",
- ipcnum,
- pDrvData->IPCs[ipcnum].usIntCount);
if (ipcnum >= ARRAY_SIZE(pDrvData->IPCs)) {
PRINTK_ERROR(KERN_ERR_MWAVE
"mwavedd::mwave_ioctl:"
" Invalid ipcnum %x\n", ipcnum);
return -EINVAL;
}
+ PRINTK_3(TRACE_MWAVE,
+ "mwavedd::mwave_ioctl IOCTL_MW_GET_IPC"
+ " ipcnum %x, usIntCount %x\n",
+ ipcnum,
+ pDrvData->IPCs[ipcnum].usIntCount);
lock_kernel();
if (pDrvData->IPCs[ipcnum].bIsEnabled == TRUE) {
return 0;
}
+/* Traditional BSD devices */
+#ifdef CONFIG_LEGACY_PTYS
+
static int pty_install(struct tty_driver *driver, struct tty_struct *tty)
{
struct tty_struct *o_tty;
return -ENOMEM;
}
-
-static const struct tty_operations pty_ops = {
- .install = pty_install,
- .open = pty_open,
- .close = pty_close,
- .write = pty_write,
- .write_room = pty_write_room,
- .flush_buffer = pty_flush_buffer,
- .chars_in_buffer = pty_chars_in_buffer,
- .unthrottle = pty_unthrottle,
- .set_termios = pty_set_termios,
- .resize = pty_resize
-};
-
-/* Traditional BSD devices */
-#ifdef CONFIG_LEGACY_PTYS
-static struct tty_driver *pty_driver, *pty_slave_driver;
-
static int pty_bsd_ioctl(struct tty_struct *tty, struct file *file,
unsigned int cmd, unsigned long arg)
{
static int legacy_count = CONFIG_LEGACY_PTY_COUNT;
module_param(legacy_count, int, 0);
-static const struct tty_operations pty_ops_bsd = {
+/*
+ * The master side of a pty can do TIOCSPTLCK and thus
+ * has pty_bsd_ioctl.
+ */
+static const struct tty_operations master_pty_ops_bsd = {
+ .install = pty_install,
.open = pty_open,
.close = pty_close,
.write = pty_write,
.resize = pty_resize
};
+static const struct tty_operations slave_pty_ops_bsd = {
+ .install = pty_install,
+ .open = pty_open,
+ .close = pty_close,
+ .write = pty_write,
+ .write_room = pty_write_room,
+ .flush_buffer = pty_flush_buffer,
+ .chars_in_buffer = pty_chars_in_buffer,
+ .unthrottle = pty_unthrottle,
+ .set_termios = pty_set_termios,
+ .resize = pty_resize
+};
+
static void __init legacy_pty_init(void)
{
+ struct tty_driver *pty_driver, *pty_slave_driver;
+
if (legacy_count <= 0)
return;
pty_driver->init_termios.c_ospeed = 38400;
pty_driver->flags = TTY_DRIVER_RESET_TERMIOS | TTY_DRIVER_REAL_RAW;
pty_driver->other = pty_slave_driver;
- tty_set_operations(pty_driver, &pty_ops);
+ tty_set_operations(pty_driver, &master_pty_ops_bsd);
pty_slave_driver->owner = THIS_MODULE;
pty_slave_driver->driver_name = "pty_slave";
pty_slave_driver->flags = TTY_DRIVER_RESET_TERMIOS |
TTY_DRIVER_REAL_RAW;
pty_slave_driver->other = pty_driver;
- tty_set_operations(pty_slave_driver, &pty_ops);
+ tty_set_operations(pty_slave_driver, &slave_pty_ops_bsd);
if (tty_register_driver(pty_driver))
panic("Couldn't register pty driver");
* as an ASCII string in the standard UUID format. If accesses via the
* sysctl system call, it is returned as 16 bytes of binary data.
*/
-static int proc_do_uuid(ctl_table *table, int write, struct file *filp,
+static int proc_do_uuid(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
ctl_table fake_table;
fake_table.data = buf;
fake_table.maxlen = sizeof(buf);
- return proc_dostring(&fake_table, write, filp, buffer, lenp, ppos);
+ return proc_dostring(&fake_table, write, buffer, lenp, ppos);
}
static int uuid_strategy(ctl_table *table,
/*
** It is important that the product code is an unsigned object!
*/
- if (DownLoad.ProductCode > MAX_PRODUCT) {
+ if (DownLoad.ProductCode >= MAX_PRODUCT) {
rio_dprintk(RIO_DEBUG_CTRL, "RIO_DOWNLOAD: Bad product code %d passed\n", DownLoad.ProductCode);
p->RIOError.Error = NO_SUCH_PRODUCT;
return -ENXIO;
return 1;
}
- if ((long)info < (long)(&cy_port[0])
- || (long)(&cy_port[NR_PORTS]) < (long)info) {
+ if (info < &cy_port[0] || info >= &cy_port[NR_PORTS]) {
printk("Warning: cyclades_port out of range for (%s) in %s\n",
name, routine);
return 1;
panic("TxInt on debug port!!!");
}
#endif
-
- info = &cy_port[channel];
-
/* validate the port number (as configured and open) */
if ((channel < 0) || (NR_PORTS <= channel)) {
base_addr[CyIER] &= ~(CyTxMpty | CyTxRdy);
base_addr[CyTEOIR] = CyNOTRANS;
return IRQ_HANDLED;
}
+ info = &cy_port[channel];
info->last_active = jiffies;
if (info->tty == 0) {
base_addr[CyIER] &= ~(CyTxMpty | CyTxRdy);
* of ttys that the driver keeps.
*
* This method gets called from a work queue so that the driver private
- * shutdown ops can sleep (needed for USB at least)
+ * cleanup ops can sleep (needed for USB at least)
*/
static void release_one_tty(struct work_struct *work)
{
container_of(work, struct tty_struct, hangup_work);
struct tty_driver *driver = tty->driver;
- if (tty->ops->shutdown)
- tty->ops->shutdown(tty);
- else
- tty_shutdown(tty);
+ if (tty->ops->cleanup)
+ tty->ops->cleanup(tty);
+
tty->magic = 0;
tty_driver_kref_put(driver);
module_put(driver->owner);
static void queue_release_one_tty(struct kref *kref)
{
struct tty_struct *tty = container_of(kref, struct tty_struct, kref);
+
+ if (tty->ops->shutdown)
+ tty->ops->shutdown(tty);
+ else
+ tty_shutdown(tty);
+
/* The hangup queue is now free so we can reuse it rather than
waste a chunk of memory for each port */
INIT_WORK(&tty->hangup_work, release_one_tty);
static int tty_ldisc_halt(struct tty_struct *tty)
{
clear_bit(TTY_LDISC, &tty->flags);
- return cancel_delayed_work(&tty->buf.work);
+ return cancel_delayed_work_sync(&tty->buf.work);
}
/**
* N_TTY.
*/
if (tty->driver->flags & TTY_DRIVER_RESET_TERMIOS) {
- /* Make sure the old ldisc is quiescent */
- tty_ldisc_halt(tty);
- flush_scheduled_work();
-
/* Avoid racing set_ldisc or tty_ldisc_release */
mutex_lock(&tty->ldisc_mutex);
+ tty_ldisc_halt(tty);
if (tty->ldisc) { /* Not yet closed */
/* Switch back to N_TTY */
tty_ldisc_reinit(tty);
--- /dev/null
+/*
+ * Timer device implementation for SGI UV platform.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2009 Silicon Graphics, Inc. All rights reserved.
+ *
+ */
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/ioctl.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/mm.h>
+#include <linux/fs.h>
+#include <linux/mmtimer.h>
+#include <linux/miscdevice.h>
+#include <linux/posix-timers.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/math64.h>
+#include <linux/smp_lock.h>
+
+#include <asm/genapic.h>
+#include <asm/uv/uv_hub.h>
+#include <asm/uv/bios.h>
+#include <asm/uv/uv.h>
+
+MODULE_AUTHOR("Dimitri Sivanich <sivanich@sgi.com>");
+MODULE_DESCRIPTION("SGI UV Memory Mapped RTC Timer");
+MODULE_LICENSE("GPL");
+
+/* name of the device, usually in /dev */
+#define UV_MMTIMER_NAME "mmtimer"
+#define UV_MMTIMER_DESC "SGI UV Memory Mapped RTC Timer"
+#define UV_MMTIMER_VERSION "1.0"
+
+static long uv_mmtimer_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg);
+static int uv_mmtimer_mmap(struct file *file, struct vm_area_struct *vma);
+
+/*
+ * Period in femtoseconds (10^-15 s)
+ */
+static unsigned long uv_mmtimer_femtoperiod;
+
+static const struct file_operations uv_mmtimer_fops = {
+ .owner = THIS_MODULE,
+ .mmap = uv_mmtimer_mmap,
+ .unlocked_ioctl = uv_mmtimer_ioctl,
+};
+
+/**
+ * uv_mmtimer_ioctl - ioctl interface for /dev/uv_mmtimer
+ * @file: file structure for the device
+ * @cmd: command to execute
+ * @arg: optional argument to command
+ *
+ * Executes the command specified by @cmd. Returns 0 for success, < 0 for
+ * failure.
+ *
+ * Valid commands:
+ *
+ * %MMTIMER_GETOFFSET - Should return the offset (relative to the start
+ * of the page where the registers are mapped) for the counter in question.
+ *
+ * %MMTIMER_GETRES - Returns the resolution of the clock in femto (10^-15)
+ * seconds
+ *
+ * %MMTIMER_GETFREQ - Copies the frequency of the clock in Hz to the address
+ * specified by @arg
+ *
+ * %MMTIMER_GETBITS - Returns the number of bits in the clock's counter
+ *
+ * %MMTIMER_MMAPAVAIL - Returns 1 if registers can be mmap'd into userspace
+ *
+ * %MMTIMER_GETCOUNTER - Gets the current value in the counter and places it
+ * in the address specified by @arg.
+ */
+static long uv_mmtimer_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
+{
+ int ret = 0;
+
+ switch (cmd) {
+ case MMTIMER_GETOFFSET: /* offset of the counter */
+ /*
+ * UV RTC register is on its own page
+ */
+ if (PAGE_SIZE <= (1 << 16))
+ ret = ((UV_LOCAL_MMR_BASE | UVH_RTC) & (PAGE_SIZE-1))
+ / 8;
+ else
+ ret = -ENOSYS;
+ break;
+
+ case MMTIMER_GETRES: /* resolution of the clock in 10^-15 s */
+ if (copy_to_user((unsigned long __user *)arg,
+ &uv_mmtimer_femtoperiod, sizeof(unsigned long)))
+ ret = -EFAULT;
+ break;
+
+ case MMTIMER_GETFREQ: /* frequency in Hz */
+ if (copy_to_user((unsigned long __user *)arg,
+ &sn_rtc_cycles_per_second,
+ sizeof(unsigned long)))
+ ret = -EFAULT;
+ break;
+
+ case MMTIMER_GETBITS: /* number of bits in the clock */
+ ret = hweight64(UVH_RTC_REAL_TIME_CLOCK_MASK);
+ break;
+
+ case MMTIMER_MMAPAVAIL: /* can we mmap the clock into userspace? */
+ ret = (PAGE_SIZE <= (1 << 16)) ? 1 : 0;
+ break;
+
+ case MMTIMER_GETCOUNTER:
+ if (copy_to_user((unsigned long __user *)arg,
+ (unsigned long *)uv_local_mmr_address(UVH_RTC),
+ sizeof(unsigned long)))
+ ret = -EFAULT;
+ break;
+ default:
+ ret = -ENOTTY;
+ break;
+ }
+ return ret;
+}
+
+/**
+ * uv_mmtimer_mmap - maps the clock's registers into userspace
+ * @file: file structure for the device
+ * @vma: VMA to map the registers into
+ *
+ * Calls remap_pfn_range() to map the clock's registers into
+ * the calling process' address space.
+ */
+static int uv_mmtimer_mmap(struct file *file, struct vm_area_struct *vma)
+{
+ unsigned long uv_mmtimer_addr;
+
+ if (vma->vm_end - vma->vm_start != PAGE_SIZE)
+ return -EINVAL;
+
+ if (vma->vm_flags & VM_WRITE)
+ return -EPERM;
+
+ if (PAGE_SIZE > (1 << 16))
+ return -ENOSYS;
+
+ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+
+ uv_mmtimer_addr = UV_LOCAL_MMR_BASE | UVH_RTC;
+ uv_mmtimer_addr &= ~(PAGE_SIZE - 1);
+ uv_mmtimer_addr &= 0xfffffffffffffffUL;
+
+ if (remap_pfn_range(vma, vma->vm_start, uv_mmtimer_addr >> PAGE_SHIFT,
+ PAGE_SIZE, vma->vm_page_prot)) {
+ printk(KERN_ERR "remap_pfn_range failed in uv_mmtimer_mmap\n");
+ return -EAGAIN;
+ }
+
+ return 0;
+}
+
+static struct miscdevice uv_mmtimer_miscdev = {
+ MISC_DYNAMIC_MINOR,
+ UV_MMTIMER_NAME,
+ &uv_mmtimer_fops
+};
+
+
+/**
+ * uv_mmtimer_init - device initialization routine
+ *
+ * Does initial setup for the uv_mmtimer device.
+ */
+static int __init uv_mmtimer_init(void)
+{
+ if (!is_uv_system()) {
+ printk(KERN_ERR "%s: Hardware unsupported\n", UV_MMTIMER_NAME);
+ return -1;
+ }
+
+ /*
+ * Sanity check the cycles/sec variable
+ */
+ if (sn_rtc_cycles_per_second < 100000) {
+ printk(KERN_ERR "%s: unable to determine clock frequency\n",
+ UV_MMTIMER_NAME);
+ return -1;
+ }
+
+ uv_mmtimer_femtoperiod = ((unsigned long)1E15 +
+ sn_rtc_cycles_per_second / 2) /
+ sn_rtc_cycles_per_second;
+
+ if (misc_register(&uv_mmtimer_miscdev)) {
+ printk(KERN_ERR "%s: failed to register device\n",
+ UV_MMTIMER_NAME);
+ return -1;
+ }
+
+ printk(KERN_INFO "%s: v%s, %ld MHz\n", UV_MMTIMER_DESC,
+ UV_MMTIMER_VERSION,
+ sn_rtc_cycles_per_second/(unsigned long)1E6);
+
+ return 0;
+}
+
+module_init(uv_mmtimer_init);
goto eperm;
if (copy_from_user(&vsa, (struct vt_setactivate __user *)arg,
- sizeof(struct vt_setactivate)))
- return -EFAULT;
+ sizeof(struct vt_setactivate))) {
+ ret = -EFAULT;
+ goto out;
+ }
if (vsa.console == 0 || vsa.console > MAX_NR_CONSOLES)
ret = -ENXIO;
else {
return status;
}
-static struct file_operations hwicap_fops = {
+static const struct file_operations hwicap_fops = {
.owner = THIS_MODULE,
.write = hwicap_write,
.read = hwicap_read,
struct cn_callback_entry *cbq =
container_of(work, struct cn_callback_entry, work);
struct cn_callback_data *d = &cbq->data;
+ struct cn_msg *msg = NLMSG_DATA(nlmsg_hdr(d->skb));
+ struct netlink_skb_parms *nsp = &NETLINK_CB(d->skb);
- d->callback(d->callback_priv);
+ d->callback(msg, nsp);
- d->destruct_data(d->ddata);
- d->ddata = NULL;
+ kfree_skb(d->skb);
+ d->skb = NULL;
kfree(d->free);
}
static struct cn_callback_entry *
cn_queue_alloc_callback_entry(char *name, struct cb_id *id,
- void (*callback)(struct cn_msg *))
+ void (*callback)(struct cn_msg *, struct netlink_skb_parms *))
{
struct cn_callback_entry *cbq;
}
int cn_queue_add_callback(struct cn_queue_dev *dev, char *name, struct cb_id *id,
- void (*callback)(struct cn_msg *))
+ void (*callback)(struct cn_msg *, struct netlink_skb_parms *))
{
struct cn_callback_entry *cbq, *__cbq;
int found = 0;
/*
* Callback helper - queues work and setup destructor for given data.
*/
-static int cn_call_callback(struct cn_msg *msg, void (*destruct_data)(void *), void *data)
+static int cn_call_callback(struct sk_buff *skb)
{
struct cn_callback_entry *__cbq, *__new_cbq;
struct cn_dev *dev = &cdev;
+ struct cn_msg *msg = NLMSG_DATA(nlmsg_hdr(skb));
int err = -ENODEV;
spin_lock_bh(&dev->cbdev->queue_lock);
list_for_each_entry(__cbq, &dev->cbdev->queue_list, callback_entry) {
if (cn_cb_equal(&__cbq->id.id, &msg->id)) {
if (likely(!work_pending(&__cbq->work) &&
- __cbq->data.ddata == NULL)) {
- __cbq->data.callback_priv = msg;
-
- __cbq->data.ddata = data;
- __cbq->data.destruct_data = destruct_data;
+ __cbq->data.skb == NULL)) {
+ __cbq->data.skb = skb;
if (queue_cn_work(__cbq, &__cbq->work))
err = 0;
__new_cbq = kzalloc(sizeof(struct cn_callback_entry), GFP_ATOMIC);
if (__new_cbq) {
d = &__new_cbq->data;
- d->callback_priv = msg;
+ d->skb = skb;
d->callback = __cbq->data.callback;
- d->ddata = data;
- d->destruct_data = destruct_data;
d->free = __new_cbq;
__new_cbq->pdev = __cbq->pdev;
*/
static void cn_rx_skb(struct sk_buff *__skb)
{
- struct cn_msg *msg;
struct nlmsghdr *nlh;
int err;
struct sk_buff *skb;
return;
}
- msg = NLMSG_DATA(nlh);
- err = cn_call_callback(msg, (void (*)(void *))kfree_skb, skb);
+ err = cn_call_callback(skb);
if (err < 0)
kfree_skb(skb);
}
* May sleep.
*/
int cn_add_callback(struct cb_id *id, char *name,
- void (*callback)(struct cn_msg *))
+ void (*callback)(struct cn_msg *, struct netlink_skb_parms *))
{
int err;
struct cn_dev *dev = &cdev;
*
* Used for notification of a request's processing.
*/
-static void cn_callback(struct cn_msg *msg)
+static void cn_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
struct cn_ctl_msg *ctl;
struct cn_ctl_entry *ent;
#include <linux/device.h>
#include <linux/dca.h>
-#define DCA_VERSION "1.8"
+#define DCA_VERSION "1.12.1"
MODULE_VERSION(DCA_VERSION);
MODULE_LICENSE("GPL");
static DEFINE_SPINLOCK(dca_lock);
-static LIST_HEAD(dca_providers);
+static LIST_HEAD(dca_domains);
-static struct dca_provider *dca_find_provider_by_dev(struct device *dev)
+static struct pci_bus *dca_pci_rc_from_dev(struct device *dev)
{
- struct dca_provider *dca, *ret = NULL;
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct pci_bus *bus = pdev->bus;
- list_for_each_entry(dca, &dca_providers, node) {
- if ((!dev) || (dca->ops->dev_managed(dca, dev))) {
- ret = dca;
- break;
- }
+ while (bus->parent)
+ bus = bus->parent;
+
+ return bus;
+}
+
+static struct dca_domain *dca_allocate_domain(struct pci_bus *rc)
+{
+ struct dca_domain *domain;
+
+ domain = kzalloc(sizeof(*domain), GFP_NOWAIT);
+ if (!domain)
+ return NULL;
+
+ INIT_LIST_HEAD(&domain->dca_providers);
+ domain->pci_rc = rc;
+
+ return domain;
+}
+
+static void dca_free_domain(struct dca_domain *domain)
+{
+ list_del(&domain->node);
+ kfree(domain);
+}
+
+static struct dca_domain *dca_find_domain(struct pci_bus *rc)
+{
+ struct dca_domain *domain;
+
+ list_for_each_entry(domain, &dca_domains, node)
+ if (domain->pci_rc == rc)
+ return domain;
+
+ return NULL;
+}
+
+static struct dca_domain *dca_get_domain(struct device *dev)
+{
+ struct pci_bus *rc;
+ struct dca_domain *domain;
+
+ rc = dca_pci_rc_from_dev(dev);
+ domain = dca_find_domain(rc);
+
+ if (!domain) {
+ domain = dca_allocate_domain(rc);
+ if (domain)
+ list_add(&domain->node, &dca_domains);
+ }
+
+ return domain;
+}
+
+static struct dca_provider *dca_find_provider_by_dev(struct device *dev)
+{
+ struct dca_provider *dca;
+ struct pci_bus *rc;
+ struct dca_domain *domain;
+
+ if (dev) {
+ rc = dca_pci_rc_from_dev(dev);
+ domain = dca_find_domain(rc);
+ if (!domain)
+ return NULL;
+ } else {
+ if (!list_empty(&dca_domains))
+ domain = list_first_entry(&dca_domains,
+ struct dca_domain,
+ node);
+ else
+ return NULL;
}
- return ret;
+ list_for_each_entry(dca, &domain->dca_providers, node)
+ if ((!dev) || (dca->ops->dev_managed(dca, dev)))
+ return dca;
+
+ return NULL;
}
/**
struct dca_provider *dca;
int err, slot = -ENODEV;
unsigned long flags;
+ struct pci_bus *pci_rc;
+ struct dca_domain *domain;
if (!dev)
return -EFAULT;
return -EEXIST;
}
- list_for_each_entry(dca, &dca_providers, node) {
+ pci_rc = dca_pci_rc_from_dev(dev);
+ domain = dca_find_domain(pci_rc);
+ if (!domain) {
+ spin_unlock_irqrestore(&dca_lock, flags);
+ return -ENODEV;
+ }
+
+ list_for_each_entry(dca, &domain->dca_providers, node) {
slot = dca->ops->add_requester(dca, dev);
if (slot >= 0)
break;
{
int err;
unsigned long flags;
+ struct dca_domain *domain;
err = dca_sysfs_add_provider(dca, dev);
if (err)
return err;
spin_lock_irqsave(&dca_lock, flags);
- list_add(&dca->node, &dca_providers);
+ domain = dca_get_domain(dev);
+ if (!domain) {
+ spin_unlock_irqrestore(&dca_lock, flags);
+ return -ENODEV;
+ }
+ list_add(&dca->node, &domain->dca_providers);
spin_unlock_irqrestore(&dca_lock, flags);
blocking_notifier_call_chain(&dca_provider_chain,
* unregister_dca_provider - remove a dca provider
* @dca - struct created by alloc_dca_provider()
*/
-void unregister_dca_provider(struct dca_provider *dca)
+void unregister_dca_provider(struct dca_provider *dca, struct device *dev)
{
unsigned long flags;
+ struct pci_bus *pci_rc;
+ struct dca_domain *domain;
blocking_notifier_call_chain(&dca_provider_chain,
DCA_PROVIDER_REMOVE, NULL);
spin_lock_irqsave(&dca_lock, flags);
+
list_del(&dca->node);
+
+ pci_rc = dca_pci_rc_from_dev(dev);
+ domain = dca_find_domain(pci_rc);
+ if (list_empty(&domain->dca_providers))
+ dca_free_domain(domain);
+
spin_unlock_irqrestore(&dca_lock, flags);
dca_sysfs_remove_provider(dca);
static int __init dca_init(void)
{
- printk(KERN_ERR "dca service started, version %s\n", DCA_VERSION);
+ pr_info("dca service started, version %s\n", DCA_VERSION);
return dca_sysfs_init();
}
comment "DMA Devices"
+config ASYNC_TX_DISABLE_CHANNEL_SWITCH
+ bool
+
config INTEL_IOATDMA
tristate "Intel I/OAT DMA support"
depends on PCI && X86
select DMA_ENGINE
select DCA
+ select ASYNC_TX_DISABLE_CHANNEL_SWITCH
help
Enable support for the Intel(R) I/OAT DMA engine present
in recent Intel Xeon chipsets.
Support the TXx9 SoC internal DMA controller. This can be
integrated in chips such as the Toshiba TX4927/38/39.
+config SH_DMAE
+ tristate "Renesas SuperH DMAC support"
+ depends on SUPERH && SH_DMA
+ depends on !SH_DMA_API
+ select DMA_ENGINE
+ help
+ Enable support for the Renesas SuperH DMA controllers.
+
config DMA_ENGINE
bool
config ASYNC_TX_DMA
bool "Async_tx: Offload support for the async_tx api"
- depends on DMA_ENGINE && !HIGHMEM64G
+ depends on DMA_ENGINE
help
This allows the async_tx api to take advantage of offload engines for
memcpy, memset, xor, and raid6 p+q operations. If your platform has
obj-$(CONFIG_DMA_ENGINE) += dmaengine.o
obj-$(CONFIG_NET_DMA) += iovlock.o
obj-$(CONFIG_DMATEST) += dmatest.o
-obj-$(CONFIG_INTEL_IOATDMA) += ioatdma.o
-ioatdma-objs := ioat.o ioat_dma.o ioat_dca.o
+obj-$(CONFIG_INTEL_IOATDMA) += ioat/
obj-$(CONFIG_INTEL_IOP_ADMA) += iop-adma.o
obj-$(CONFIG_FSL_DMA) += fsldma.o
obj-$(CONFIG_MV_XOR) += mv_xor.o
obj-$(CONFIG_AT_HDMAC) += at_hdmac.o
obj-$(CONFIG_MX3_IPU) += ipu/
obj-$(CONFIG_TXX9_DMAC) += txx9dmac.o
+obj-$(CONFIG_SH_DMAE) += shdma.o
desc = dma_pool_alloc(atdma->dma_desc_pool, gfp_flags, &phys);
if (desc) {
memset(desc, 0, sizeof(struct at_desc));
+ INIT_LIST_HEAD(&desc->tx_list);
dma_async_tx_descriptor_init(&desc->txd, chan);
/* txd.flags will be overwritten in prep functions */
desc->txd.flags = DMA_CTRL_ACK;
struct at_desc *child;
spin_lock_bh(&atchan->lock);
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
dev_vdbg(chan2dev(&atchan->chan_common),
"moving child desc %p to freelist\n",
child);
- list_splice_init(&desc->txd.tx_list, &atchan->free_list);
+ list_splice_init(&desc->tx_list, &atchan->free_list);
dev_vdbg(chan2dev(&atchan->chan_common),
"moving desc %p to freelist\n", desc);
list_add(&desc->desc_node, &atchan->free_list);
param = txd->callback_param;
/* move children to free_list */
- list_splice_init(&txd->tx_list, &atchan->free_list);
+ list_splice_init(&desc->tx_list, &atchan->free_list);
/* move myself to free_list */
list_move(&desc->desc_node, &atchan->free_list);
/* unmap dma addresses */
- if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
- if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE)
- dma_unmap_single(chan2parent(&atchan->chan_common),
- desc->lli.daddr,
- desc->len, DMA_FROM_DEVICE);
- else
- dma_unmap_page(chan2parent(&atchan->chan_common),
- desc->lli.daddr,
- desc->len, DMA_FROM_DEVICE);
- }
- if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
- if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE)
- dma_unmap_single(chan2parent(&atchan->chan_common),
- desc->lli.saddr,
- desc->len, DMA_TO_DEVICE);
- else
- dma_unmap_page(chan2parent(&atchan->chan_common),
- desc->lli.saddr,
- desc->len, DMA_TO_DEVICE);
+ if (!atchan->chan_common.private) {
+ struct device *parent = chan2parent(&atchan->chan_common);
+ if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+ if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE)
+ dma_unmap_single(parent,
+ desc->lli.daddr,
+ desc->len, DMA_FROM_DEVICE);
+ else
+ dma_unmap_page(parent,
+ desc->lli.daddr,
+ desc->len, DMA_FROM_DEVICE);
+ }
+ if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE)
+ dma_unmap_single(parent,
+ desc->lli.saddr,
+ desc->len, DMA_TO_DEVICE);
+ else
+ dma_unmap_page(parent,
+ desc->lli.saddr,
+ desc->len, DMA_TO_DEVICE);
+ }
}
/*
/* This one is currently in progress */
return;
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
if (!(child->lli.ctrla & ATC_DONE))
/* Currently in progress */
return;
dev_crit(chan2dev(&atchan->chan_common),
" cookie: %d\n", bad_desc->txd.cookie);
atc_dump_lli(atchan, &bad_desc->lli);
- list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &bad_desc->tx_list, desc_node)
atc_dump_lli(atchan, &child->lli);
/* Pretend the descriptor completed successfully */
prev->lli.dscr = desc->txd.phys;
/* insert the link descriptor to the LD ring */
list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ &first->tx_list);
}
prev = desc;
}
reg_width = atslave->reg_width;
- sg_len = dma_map_sg(chan2parent(chan), sgl, sg_len, direction);
-
ctrla = ATC_DEFAULT_CTRLA | atslave->ctrla;
ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN;
prev->lli.dscr = desc->txd.phys;
/* insert the link descriptor to the LD ring */
list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ &first->tx_list);
}
prev = desc;
total_len += len;
prev->lli.dscr = desc->txd.phys;
/* insert the link descriptor to the LD ring */
list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ &first->tx_list);
}
prev = desc;
total_len += len;
struct at_lli lli;
/* THEN values for driver housekeeping */
+ struct list_head tx_list;
struct dma_async_tx_descriptor txd;
struct list_head desc_node;
size_t len;
}
EXPORT_SYMBOL(dmaengine_put);
+static bool device_has_all_tx_types(struct dma_device *device)
+{
+ /* A device that satisfies this test has channels that will never cause
+ * an async_tx channel switch event as all possible operation types can
+ * be handled.
+ */
+ #ifdef CONFIG_ASYNC_TX_DMA
+ if (!dma_has_cap(DMA_INTERRUPT, device->cap_mask))
+ return false;
+ #endif
+
+ #if defined(CONFIG_ASYNC_MEMCPY) || defined(CONFIG_ASYNC_MEMCPY_MODULE)
+ if (!dma_has_cap(DMA_MEMCPY, device->cap_mask))
+ return false;
+ #endif
+
+ #if defined(CONFIG_ASYNC_MEMSET) || defined(CONFIG_ASYNC_MEMSET_MODULE)
+ if (!dma_has_cap(DMA_MEMSET, device->cap_mask))
+ return false;
+ #endif
+
+ #if defined(CONFIG_ASYNC_XOR) || defined(CONFIG_ASYNC_XOR_MODULE)
+ if (!dma_has_cap(DMA_XOR, device->cap_mask))
+ return false;
+ #endif
+
+ #if defined(CONFIG_ASYNC_PQ) || defined(CONFIG_ASYNC_PQ_MODULE)
+ if (!dma_has_cap(DMA_PQ, device->cap_mask))
+ return false;
+ #endif
+
+ return true;
+}
+
static int get_dma_id(struct dma_device *device)
{
int rc;
!device->device_prep_dma_memcpy);
BUG_ON(dma_has_cap(DMA_XOR, device->cap_mask) &&
!device->device_prep_dma_xor);
- BUG_ON(dma_has_cap(DMA_ZERO_SUM, device->cap_mask) &&
- !device->device_prep_dma_zero_sum);
+ BUG_ON(dma_has_cap(DMA_XOR_VAL, device->cap_mask) &&
+ !device->device_prep_dma_xor_val);
+ BUG_ON(dma_has_cap(DMA_PQ, device->cap_mask) &&
+ !device->device_prep_dma_pq);
+ BUG_ON(dma_has_cap(DMA_PQ_VAL, device->cap_mask) &&
+ !device->device_prep_dma_pq_val);
BUG_ON(dma_has_cap(DMA_MEMSET, device->cap_mask) &&
!device->device_prep_dma_memset);
BUG_ON(dma_has_cap(DMA_INTERRUPT, device->cap_mask) &&
BUG_ON(!device->device_issue_pending);
BUG_ON(!device->dev);
+ /* note: this only matters in the
+ * CONFIG_ASYNC_TX_DISABLE_CHANNEL_SWITCH=y case
+ */
+ if (device_has_all_tx_types(device))
+ dma_cap_set(DMA_ASYNC_TX, device->cap_mask);
+
idr_ref = kmalloc(sizeof(*idr_ref), GFP_KERNEL);
if (!idr_ref)
return -ENOMEM;
{
tx->chan = chan;
spin_lock_init(&tx->lock);
- INIT_LIST_HEAD(&tx->tx_list);
}
EXPORT_SYMBOL(dma_async_tx_descriptor_init);
/* dma_wait_for_async_tx - spin wait for a transaction to complete
* @tx: in-flight transaction to wait on
- *
- * This routine assumes that tx was obtained from a call to async_memcpy,
- * async_xor, async_memset, etc which ensures that tx is "in-flight" (prepped
- * and submitted). Walking the parent chain is only meant to cover for DMA
- * drivers that do not implement the DMA_INTERRUPT capability and may race with
- * the driver's descriptor cleanup routine.
*/
enum dma_status
dma_wait_for_async_tx(struct dma_async_tx_descriptor *tx)
{
- enum dma_status status;
- struct dma_async_tx_descriptor *iter;
- struct dma_async_tx_descriptor *parent;
+ unsigned long dma_sync_wait_timeout = jiffies + msecs_to_jiffies(5000);
if (!tx)
return DMA_SUCCESS;
- WARN_ONCE(tx->parent, "%s: speculatively walking dependency chain for"
- " %s\n", __func__, dma_chan_name(tx->chan));
-
- /* poll through the dependency chain, return when tx is complete */
- do {
- iter = tx;
-
- /* find the root of the unsubmitted dependency chain */
- do {
- parent = iter->parent;
- if (!parent)
- break;
- else
- iter = parent;
- } while (parent);
-
- /* there is a small window for ->parent == NULL and
- * ->cookie == -EBUSY
- */
- while (iter->cookie == -EBUSY)
- cpu_relax();
-
- status = dma_sync_wait(iter->chan, iter->cookie);
- } while (status == DMA_IN_PROGRESS || (iter != tx));
-
- return status;
+ while (tx->cookie == -EBUSY) {
+ if (time_after_eq(jiffies, dma_sync_wait_timeout)) {
+ pr_err("%s timeout waiting for descriptor submission\n",
+ __func__);
+ return DMA_ERROR;
+ }
+ cpu_relax();
+ }
+ return dma_sync_wait(tx->chan, tx->cookie);
}
EXPORT_SYMBOL_GPL(dma_wait_for_async_tx);
MODULE_PARM_DESC(xor_sources,
"Number of xor source buffers (default: 3)");
+static unsigned int pq_sources = 3;
+module_param(pq_sources, uint, S_IRUGO);
+MODULE_PARM_DESC(pq_sources,
+ "Number of p+q source buffers (default: 3)");
+
/*
* Initialization patterns. All bytes in the source buffer has bit 7
* set, all bytes in the destination buffer has bit 7 cleared.
dma_cookie_t cookie;
enum dma_status status;
enum dma_ctrl_flags flags;
+ u8 pq_coefs[pq_sources];
int ret;
int src_cnt;
int dst_cnt;
else if (thread->type == DMA_XOR) {
src_cnt = xor_sources | 1; /* force odd to ensure dst = src */
dst_cnt = 1;
+ } else if (thread->type == DMA_PQ) {
+ src_cnt = pq_sources | 1; /* force odd to ensure dst = src */
+ dst_cnt = 2;
+ for (i = 0; i < pq_sources; i++)
+ pq_coefs[i] = 1;
} else
goto err_srcs;
dma_addr_t dma_dsts[dst_cnt];
struct completion cmp;
unsigned long tmo = msecs_to_jiffies(3000);
+ u8 align = 0;
total_tests++;
src_off = dmatest_random() % (test_buf_size - len + 1);
dst_off = dmatest_random() % (test_buf_size - len + 1);
+ /* honor alignment restrictions */
+ if (thread->type == DMA_MEMCPY)
+ align = dev->copy_align;
+ else if (thread->type == DMA_XOR)
+ align = dev->xor_align;
+ else if (thread->type == DMA_PQ)
+ align = dev->pq_align;
+
+ len = (len >> align) << align;
+ src_off = (src_off >> align) << align;
+ dst_off = (dst_off >> align) << align;
+
dmatest_init_srcs(thread->srcs, src_off, len);
dmatest_init_dsts(thread->dsts, dst_off, len);
DMA_BIDIRECTIONAL);
}
+
if (thread->type == DMA_MEMCPY)
tx = dev->device_prep_dma_memcpy(chan,
dma_dsts[0] + dst_off,
dma_dsts[0] + dst_off,
dma_srcs, xor_sources,
len, flags);
+ else if (thread->type == DMA_PQ) {
+ dma_addr_t dma_pq[dst_cnt];
+
+ for (i = 0; i < dst_cnt; i++)
+ dma_pq[i] = dma_dsts[i] + dst_off;
+ tx = dev->device_prep_dma_pq(chan, dma_pq, dma_srcs,
+ pq_sources, pq_coefs,
+ len, flags);
+ }
if (!tx) {
for (i = 0; i < src_cnt; i++)
op = "copy";
else if (type == DMA_XOR)
op = "xor";
+ else if (type == DMA_PQ)
+ op = "pq";
else
return -EINVAL;
cnt = dmatest_add_threads(dtc, DMA_XOR);
thread_count += cnt > 0 ? cnt : 0;
}
+ if (dma_has_cap(DMA_PQ, dma_dev->cap_mask)) {
+ cnt = dmatest_add_threads(dtc, DMA_PQ);
+ thread_count += cnt > 0 ?: 0;
+ }
pr_info("dmatest: Started %u threads using %s\n",
thread_count, dma_chan_name(chan));
{
struct dw_desc *child;
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
dma_sync_single_for_cpu(chan2parent(&dwc->chan),
child->txd.phys, sizeof(child->lli),
DMA_TO_DEVICE);
dwc_sync_desc_for_cpu(dwc, desc);
spin_lock_bh(&dwc->lock);
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
dev_vdbg(chan2dev(&dwc->chan),
"moving child desc %p to freelist\n",
child);
- list_splice_init(&desc->txd.tx_list, &dwc->free_list);
+ list_splice_init(&desc->tx_list, &dwc->free_list);
dev_vdbg(chan2dev(&dwc->chan), "moving desc %p to freelist\n", desc);
list_add(&desc->desc_node, &dwc->free_list);
spin_unlock_bh(&dwc->lock);
param = txd->callback_param;
dwc_sync_desc_for_cpu(dwc, desc);
- list_splice_init(&txd->tx_list, &dwc->free_list);
+ list_splice_init(&desc->tx_list, &dwc->free_list);
list_move(&desc->desc_node, &dwc->free_list);
- /*
- * We use dma_unmap_page() regardless of how the buffers were
- * mapped before they were submitted...
- */
- if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP))
- dma_unmap_page(chan2parent(&dwc->chan), desc->lli.dar,
- desc->len, DMA_FROM_DEVICE);
- if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP))
- dma_unmap_page(chan2parent(&dwc->chan), desc->lli.sar,
- desc->len, DMA_TO_DEVICE);
+ if (!dwc->chan.private) {
+ struct device *parent = chan2parent(&dwc->chan);
+ if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+ if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE)
+ dma_unmap_single(parent, desc->lli.dar,
+ desc->len, DMA_FROM_DEVICE);
+ else
+ dma_unmap_page(parent, desc->lli.dar,
+ desc->len, DMA_FROM_DEVICE);
+ }
+ if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE)
+ dma_unmap_single(parent, desc->lli.sar,
+ desc->len, DMA_TO_DEVICE);
+ else
+ dma_unmap_page(parent, desc->lli.sar,
+ desc->len, DMA_TO_DEVICE);
+ }
+ }
/*
* The API requires that no submissions are done from a
/* This one is currently in progress */
return;
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
if (child->lli.llp == llp)
/* Currently in progress */
return;
dev_printk(KERN_CRIT, chan2dev(&dwc->chan),
" cookie: %d\n", bad_desc->txd.cookie);
dwc_dump_lli(dwc, &bad_desc->lli);
- list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &bad_desc->tx_list, desc_node)
dwc_dump_lli(dwc, &child->lli);
/* Pretend the descriptor completed successfully */
prev->txd.phys, sizeof(prev->lli),
DMA_TO_DEVICE);
list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ &first->tx_list);
}
prev = desc;
}
reg_width = dws->reg_width;
prev = first = NULL;
- sg_len = dma_map_sg(chan2parent(chan), sgl, sg_len, direction);
-
switch (direction) {
case DMA_TO_DEVICE:
ctllo = (DWC_DEFAULT_CTLLO
sizeof(prev->lli),
DMA_TO_DEVICE);
list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ &first->tx_list);
}
prev = desc;
total_len += len;
sizeof(prev->lli),
DMA_TO_DEVICE);
list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ &first->tx_list);
}
prev = desc;
total_len += len;
break;
}
+ INIT_LIST_HEAD(&desc->tx_list);
dma_async_tx_descriptor_init(&desc->txd, chan);
desc->txd.tx_submit = dwc_tx_submit;
desc->txd.flags = DMA_CTRL_ACK;
/* THEN values for driver housekeeping */
struct list_head desc_node;
+ struct list_head tx_list;
struct dma_async_tx_descriptor txd;
size_t len;
};
#include <linux/dmapool.h>
#include <linux/of_platform.h>
+#include <asm/fsldma.h>
#include "fsldma.h"
static void dma_init(struct fsl_dma_chan *fsl_chan)
}
/**
- * fsl_chan_toggle_ext_pause - Toggle channel external pause status
+ * fsl_chan_set_request_count - Set DMA Request Count for external control
* @fsl_chan : Freescale DMA channel
- * @size : Pause control size, 0 for disable external pause control.
- * The maximum is 1024.
+ * @size : Number of bytes to transfer in a single request
+ *
+ * The Freescale DMA channel can be controlled by the external signal DREQ#.
+ * The DMA request count is how many bytes are allowed to transfer before
+ * pausing the channel, after which a new assertion of DREQ# resumes channel
+ * operation.
*
- * The Freescale DMA channel can be controlled by the external
- * signal DREQ#. The pause control size is how many bytes are allowed
- * to transfer before pausing the channel, after which a new assertion
- * of DREQ# resumes channel operation.
+ * A size of 0 disables external pause control. The maximum size is 1024.
*/
-static void fsl_chan_toggle_ext_pause(struct fsl_dma_chan *fsl_chan, int size)
+static void fsl_chan_set_request_count(struct fsl_dma_chan *fsl_chan, int size)
{
- if (size > 1024)
- return;
+ BUG_ON(size > 1024);
+ DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr,
+ DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32)
+ | ((__ilog2(size) << 24) & 0x0f000000),
+ 32);
+}
- if (size) {
- DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr,
- DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32)
- | ((__ilog2(size) << 24) & 0x0f000000),
- 32);
+/**
+ * fsl_chan_toggle_ext_pause - Toggle channel external pause status
+ * @fsl_chan : Freescale DMA channel
+ * @enable : 0 is disabled, 1 is enabled.
+ *
+ * The Freescale DMA channel can be controlled by the external signal DREQ#.
+ * The DMA Request Count feature should be used in addition to this feature
+ * to set the number of bytes to transfer before pausing the channel.
+ */
+static void fsl_chan_toggle_ext_pause(struct fsl_dma_chan *fsl_chan, int enable)
+{
+ if (enable)
fsl_chan->feature |= FSL_DMA_CHAN_PAUSE_EXT;
- } else
+ else
fsl_chan->feature &= ~FSL_DMA_CHAN_PAUSE_EXT;
}
static dma_cookie_t fsl_dma_tx_submit(struct dma_async_tx_descriptor *tx)
{
struct fsl_dma_chan *fsl_chan = to_fsl_chan(tx->chan);
- struct fsl_desc_sw *desc;
+ struct fsl_desc_sw *desc = tx_to_fsl_desc(tx);
+ struct fsl_desc_sw *child;
unsigned long flags;
dma_cookie_t cookie;
spin_lock_irqsave(&fsl_chan->desc_lock, flags);
cookie = fsl_chan->common.cookie;
- list_for_each_entry(desc, &tx->tx_list, node) {
+ list_for_each_entry(child, &desc->tx_list, node) {
cookie++;
if (cookie < 0)
cookie = 1;
}
fsl_chan->common.cookie = cookie;
- append_ld_queue(fsl_chan, tx_to_fsl_desc(tx));
- list_splice_init(&tx->tx_list, fsl_chan->ld_queue.prev);
+ append_ld_queue(fsl_chan, desc);
+ list_splice_init(&desc->tx_list, fsl_chan->ld_queue.prev);
spin_unlock_irqrestore(&fsl_chan->desc_lock, flags);
desc_sw = dma_pool_alloc(fsl_chan->desc_pool, GFP_ATOMIC, &pdesc);
if (desc_sw) {
memset(desc_sw, 0, sizeof(struct fsl_desc_sw));
+ INIT_LIST_HEAD(&desc_sw->tx_list);
dma_async_tx_descriptor_init(&desc_sw->async_tx,
&fsl_chan->common);
desc_sw->async_tx.tx_submit = fsl_dma_tx_submit;
new->async_tx.flags = flags;
/* Insert the link descriptor to the LD ring */
- list_add_tail(&new->node, &new->async_tx.tx_list);
+ list_add_tail(&new->node, &new->tx_list);
/* Set End-of-link to the last link descriptor of new list*/
set_ld_eol(fsl_chan, new);
dma_dest += copy;
/* Insert the link descriptor to the LD ring */
- list_add_tail(&new->node, &first->async_tx.tx_list);
+ list_add_tail(&new->node, &first->tx_list);
} while (len);
new->async_tx.flags = flags; /* client is in control of this ack */
if (!first)
return NULL;
- list = &first->async_tx.tx_list;
+ list = &first->tx_list;
list_for_each_entry_safe_reverse(new, prev, list, node) {
list_del(&new->node);
dma_pool_free(fsl_chan->desc_pool, new, new->async_tx.phys);
return NULL;
}
+/**
+ * fsl_dma_prep_slave_sg - prepare descriptors for a DMA_SLAVE transaction
+ * @chan: DMA channel
+ * @sgl: scatterlist to transfer to/from
+ * @sg_len: number of entries in @scatterlist
+ * @direction: DMA direction
+ * @flags: DMAEngine flags
+ *
+ * Prepare a set of descriptors for a DMA_SLAVE transaction. Following the
+ * DMA_SLAVE API, this gets the device-specific information from the
+ * chan->private variable.
+ */
+static struct dma_async_tx_descriptor *fsl_dma_prep_slave_sg(
+ struct dma_chan *chan, struct scatterlist *sgl, unsigned int sg_len,
+ enum dma_data_direction direction, unsigned long flags)
+{
+ struct fsl_dma_chan *fsl_chan;
+ struct fsl_desc_sw *first = NULL, *prev = NULL, *new = NULL;
+ struct fsl_dma_slave *slave;
+ struct list_head *tx_list;
+ size_t copy;
+
+ int i;
+ struct scatterlist *sg;
+ size_t sg_used;
+ size_t hw_used;
+ struct fsl_dma_hw_addr *hw;
+ dma_addr_t dma_dst, dma_src;
+
+ if (!chan)
+ return NULL;
+
+ if (!chan->private)
+ return NULL;
+
+ fsl_chan = to_fsl_chan(chan);
+ slave = chan->private;
+
+ if (list_empty(&slave->addresses))
+ return NULL;
+
+ hw = list_first_entry(&slave->addresses, struct fsl_dma_hw_addr, entry);
+ hw_used = 0;
+
+ /*
+ * Build the hardware transaction to copy from the scatterlist to
+ * the hardware, or from the hardware to the scatterlist
+ *
+ * If you are copying from the hardware to the scatterlist and it
+ * takes two hardware entries to fill an entire page, then both
+ * hardware entries will be coalesced into the same page
+ *
+ * If you are copying from the scatterlist to the hardware and a
+ * single page can fill two hardware entries, then the data will
+ * be read out of the page into the first hardware entry, and so on
+ */
+ for_each_sg(sgl, sg, sg_len, i) {
+ sg_used = 0;
+
+ /* Loop until the entire scatterlist entry is used */
+ while (sg_used < sg_dma_len(sg)) {
+
+ /*
+ * If we've used up the current hardware address/length
+ * pair, we need to load a new one
+ *
+ * This is done in a while loop so that descriptors with
+ * length == 0 will be skipped
+ */
+ while (hw_used >= hw->length) {
+
+ /*
+ * If the current hardware entry is the last
+ * entry in the list, we're finished
+ */
+ if (list_is_last(&hw->entry, &slave->addresses))
+ goto finished;
+
+ /* Get the next hardware address/length pair */
+ hw = list_entry(hw->entry.next,
+ struct fsl_dma_hw_addr, entry);
+ hw_used = 0;
+ }
+
+ /* Allocate the link descriptor from DMA pool */
+ new = fsl_dma_alloc_descriptor(fsl_chan);
+ if (!new) {
+ dev_err(fsl_chan->dev, "No free memory for "
+ "link descriptor\n");
+ goto fail;
+ }
+#ifdef FSL_DMA_LD_DEBUG
+ dev_dbg(fsl_chan->dev, "new link desc alloc %p\n", new);
+#endif
+
+ /*
+ * Calculate the maximum number of bytes to transfer,
+ * making sure it is less than the DMA controller limit
+ */
+ copy = min_t(size_t, sg_dma_len(sg) - sg_used,
+ hw->length - hw_used);
+ copy = min_t(size_t, copy, FSL_DMA_BCR_MAX_CNT);
+
+ /*
+ * DMA_FROM_DEVICE
+ * from the hardware to the scatterlist
+ *
+ * DMA_TO_DEVICE
+ * from the scatterlist to the hardware
+ */
+ if (direction == DMA_FROM_DEVICE) {
+ dma_src = hw->address + hw_used;
+ dma_dst = sg_dma_address(sg) + sg_used;
+ } else {
+ dma_src = sg_dma_address(sg) + sg_used;
+ dma_dst = hw->address + hw_used;
+ }
+
+ /* Fill in the descriptor */
+ set_desc_cnt(fsl_chan, &new->hw, copy);
+ set_desc_src(fsl_chan, &new->hw, dma_src);
+ set_desc_dest(fsl_chan, &new->hw, dma_dst);
+
+ /*
+ * If this is not the first descriptor, chain the
+ * current descriptor after the previous descriptor
+ */
+ if (!first) {
+ first = new;
+ } else {
+ set_desc_next(fsl_chan, &prev->hw,
+ new->async_tx.phys);
+ }
+
+ new->async_tx.cookie = 0;
+ async_tx_ack(&new->async_tx);
+
+ prev = new;
+ sg_used += copy;
+ hw_used += copy;
+
+ /* Insert the link descriptor into the LD ring */
+ list_add_tail(&new->node, &first->tx_list);
+ }
+ }
+
+finished:
+
+ /* All of the hardware address/length pairs had length == 0 */
+ if (!first || !new)
+ return NULL;
+
+ new->async_tx.flags = flags;
+ new->async_tx.cookie = -EBUSY;
+
+ /* Set End-of-link to the last link descriptor of new list */
+ set_ld_eol(fsl_chan, new);
+
+ /* Enable extra controller features */
+ if (fsl_chan->set_src_loop_size)
+ fsl_chan->set_src_loop_size(fsl_chan, slave->src_loop_size);
+
+ if (fsl_chan->set_dest_loop_size)
+ fsl_chan->set_dest_loop_size(fsl_chan, slave->dst_loop_size);
+
+ if (fsl_chan->toggle_ext_start)
+ fsl_chan->toggle_ext_start(fsl_chan, slave->external_start);
+
+ if (fsl_chan->toggle_ext_pause)
+ fsl_chan->toggle_ext_pause(fsl_chan, slave->external_pause);
+
+ if (fsl_chan->set_request_count)
+ fsl_chan->set_request_count(fsl_chan, slave->request_count);
+
+ return &first->async_tx;
+
+fail:
+ /* If first was not set, then we failed to allocate the very first
+ * descriptor, and we're done */
+ if (!first)
+ return NULL;
+
+ /*
+ * First is set, so all of the descriptors we allocated have been added
+ * to first->tx_list, INCLUDING "first" itself. Therefore we
+ * must traverse the list backwards freeing each descriptor in turn
+ *
+ * We're re-using variables for the loop, oh well
+ */
+ tx_list = &first->tx_list;
+ list_for_each_entry_safe_reverse(new, prev, tx_list, node) {
+ list_del_init(&new->node);
+ dma_pool_free(fsl_chan->desc_pool, new, new->async_tx.phys);
+ }
+
+ return NULL;
+}
+
+static void fsl_dma_device_terminate_all(struct dma_chan *chan)
+{
+ struct fsl_dma_chan *fsl_chan;
+ struct fsl_desc_sw *desc, *tmp;
+ unsigned long flags;
+
+ if (!chan)
+ return;
+
+ fsl_chan = to_fsl_chan(chan);
+
+ /* Halt the DMA engine */
+ dma_halt(fsl_chan);
+
+ spin_lock_irqsave(&fsl_chan->desc_lock, flags);
+
+ /* Remove and free all of the descriptors in the LD queue */
+ list_for_each_entry_safe(desc, tmp, &fsl_chan->ld_queue, node) {
+ list_del(&desc->node);
+ dma_pool_free(fsl_chan->desc_pool, desc, desc->async_tx.phys);
+ }
+
+ spin_unlock_irqrestore(&fsl_chan->desc_lock, flags);
+}
+
/**
* fsl_dma_update_completed_cookie - Update the completed cookie.
* @fsl_chan : Freescale DMA channel
new_fsl_chan->toggle_ext_start = fsl_chan_toggle_ext_start;
new_fsl_chan->set_src_loop_size = fsl_chan_set_src_loop_size;
new_fsl_chan->set_dest_loop_size = fsl_chan_set_dest_loop_size;
+ new_fsl_chan->set_request_count = fsl_chan_set_request_count;
}
spin_lock_init(&new_fsl_chan->desc_lock);
dma_cap_set(DMA_MEMCPY, fdev->common.cap_mask);
dma_cap_set(DMA_INTERRUPT, fdev->common.cap_mask);
+ dma_cap_set(DMA_SLAVE, fdev->common.cap_mask);
fdev->common.device_alloc_chan_resources = fsl_dma_alloc_chan_resources;
fdev->common.device_free_chan_resources = fsl_dma_free_chan_resources;
fdev->common.device_prep_dma_interrupt = fsl_dma_prep_interrupt;
fdev->common.device_prep_dma_memcpy = fsl_dma_prep_memcpy;
fdev->common.device_is_tx_complete = fsl_dma_is_complete;
fdev->common.device_issue_pending = fsl_dma_memcpy_issue_pending;
+ fdev->common.device_prep_slave_sg = fsl_dma_prep_slave_sg;
+ fdev->common.device_terminate_all = fsl_dma_device_terminate_all;
fdev->common.dev = &dev->dev;
fdev->irq = irq_of_parse_and_map(dev->node, 0);
struct fsl_desc_sw {
struct fsl_dma_ld_hw hw;
struct list_head node;
+ struct list_head tx_list;
struct dma_async_tx_descriptor async_tx;
struct list_head *ld;
void *priv;
struct tasklet_struct tasklet;
u32 feature;
- void (*toggle_ext_pause)(struct fsl_dma_chan *fsl_chan, int size);
+ void (*toggle_ext_pause)(struct fsl_dma_chan *fsl_chan, int enable);
void (*toggle_ext_start)(struct fsl_dma_chan *fsl_chan, int enable);
void (*set_src_loop_size)(struct fsl_dma_chan *fsl_chan, int size);
void (*set_dest_loop_size)(struct fsl_dma_chan *fsl_chan, int size);
+ void (*set_request_count)(struct fsl_dma_chan *fsl_chan, int size);
};
#define to_fsl_chan(chan) container_of(chan, struct fsl_dma_chan, common)
+++ /dev/null
-/*
- * Intel I/OAT DMA Linux driver
- * Copyright(c) 2007 - 2009 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- *
- * The full GNU General Public License is included in this distribution in
- * the file called "COPYING".
- *
- */
-
-/*
- * This driver supports an Intel I/OAT DMA engine, which does asynchronous
- * copy operations.
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/dca.h>
-#include "ioatdma.h"
-#include "ioatdma_registers.h"
-#include "ioatdma_hw.h"
-
-MODULE_VERSION(IOAT_DMA_VERSION);
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Intel Corporation");
-
-static struct pci_device_id ioat_pci_tbl[] = {
- /* I/OAT v1 platforms */
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_CNB) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_SCNB) },
- { PCI_DEVICE(PCI_VENDOR_ID_UNISYS, PCI_DEVICE_ID_UNISYS_DMA_DIRECTOR) },
-
- /* I/OAT v2 platforms */
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_SNB) },
-
- /* I/OAT v3 platforms */
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG0) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG1) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG2) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG3) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG4) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG5) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG6) },
- { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG7) },
- { 0, }
-};
-
-struct ioat_device {
- struct pci_dev *pdev;
- void __iomem *iobase;
- struct ioatdma_device *dma;
- struct dca_provider *dca;
-};
-
-static int __devinit ioat_probe(struct pci_dev *pdev,
- const struct pci_device_id *id);
-static void __devexit ioat_remove(struct pci_dev *pdev);
-
-static int ioat_dca_enabled = 1;
-module_param(ioat_dca_enabled, int, 0644);
-MODULE_PARM_DESC(ioat_dca_enabled, "control support of dca service (default: 1)");
-
-static struct pci_driver ioat_pci_driver = {
- .name = "ioatdma",
- .id_table = ioat_pci_tbl,
- .probe = ioat_probe,
- .remove = __devexit_p(ioat_remove),
-};
-
-static int __devinit ioat_probe(struct pci_dev *pdev,
- const struct pci_device_id *id)
-{
- void __iomem *iobase;
- struct ioat_device *device;
- unsigned long mmio_start, mmio_len;
- int err;
-
- err = pci_enable_device(pdev);
- if (err)
- goto err_enable_device;
-
- err = pci_request_regions(pdev, ioat_pci_driver.name);
- if (err)
- goto err_request_regions;
-
- err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
- if (err)
- err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
- if (err)
- goto err_set_dma_mask;
-
- err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
- if (err)
- err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
- if (err)
- goto err_set_dma_mask;
-
- mmio_start = pci_resource_start(pdev, 0);
- mmio_len = pci_resource_len(pdev, 0);
- iobase = ioremap(mmio_start, mmio_len);
- if (!iobase) {
- err = -ENOMEM;
- goto err_ioremap;
- }
-
- device = kzalloc(sizeof(*device), GFP_KERNEL);
- if (!device) {
- err = -ENOMEM;
- goto err_kzalloc;
- }
- device->pdev = pdev;
- pci_set_drvdata(pdev, device);
- device->iobase = iobase;
-
- pci_set_master(pdev);
-
- switch (readb(iobase + IOAT_VER_OFFSET)) {
- case IOAT_VER_1_2:
- device->dma = ioat_dma_probe(pdev, iobase);
- if (device->dma && ioat_dca_enabled)
- device->dca = ioat_dca_init(pdev, iobase);
- break;
- case IOAT_VER_2_0:
- device->dma = ioat_dma_probe(pdev, iobase);
- if (device->dma && ioat_dca_enabled)
- device->dca = ioat2_dca_init(pdev, iobase);
- break;
- case IOAT_VER_3_0:
- device->dma = ioat_dma_probe(pdev, iobase);
- if (device->dma && ioat_dca_enabled)
- device->dca = ioat3_dca_init(pdev, iobase);
- break;
- default:
- err = -ENODEV;
- break;
- }
- if (!device->dma)
- err = -ENODEV;
-
- if (err)
- goto err_version;
-
- return 0;
-
-err_version:
- kfree(device);
-err_kzalloc:
- iounmap(iobase);
-err_ioremap:
-err_set_dma_mask:
- pci_release_regions(pdev);
- pci_disable_device(pdev);
-err_request_regions:
-err_enable_device:
- return err;
-}
-
-static void __devexit ioat_remove(struct pci_dev *pdev)
-{
- struct ioat_device *device = pci_get_drvdata(pdev);
-
- dev_err(&pdev->dev, "Removing dma and dca services\n");
- if (device->dca) {
- unregister_dca_provider(device->dca);
- free_dca_provider(device->dca);
- device->dca = NULL;
- }
-
- if (device->dma) {
- ioat_dma_remove(device->dma);
- device->dma = NULL;
- }
-
- kfree(device);
-}
-
-static int __init ioat_init_module(void)
-{
- return pci_register_driver(&ioat_pci_driver);
-}
-module_init(ioat_init_module);
-
-static void __exit ioat_exit_module(void)
-{
- pci_unregister_driver(&ioat_pci_driver);
-}
-module_exit(ioat_exit_module);
--- /dev/null
+obj-$(CONFIG_INTEL_IOATDMA) += ioatdma.o
+ioatdma-objs := pci.o dma.o dma_v2.o dma_v3.o dca.o
--- /dev/null
+/*
+ * Intel I/OAT DMA Linux driver
+ * Copyright(c) 2007 - 2009 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/smp.h>
+#include <linux/interrupt.h>
+#include <linux/dca.h>
+
+/* either a kernel change is needed, or we need something like this in kernel */
+#ifndef CONFIG_SMP
+#include <asm/smp.h>
+#undef cpu_physical_id
+#define cpu_physical_id(cpu) (cpuid_ebx(1) >> 24)
+#endif
+
+#include "dma.h"
+#include "registers.h"
+
+/*
+ * Bit 7 of a tag map entry is the "valid" bit, if it is set then bits 0:6
+ * contain the bit number of the APIC ID to map into the DCA tag. If the valid
+ * bit is not set, then the value must be 0 or 1 and defines the bit in the tag.
+ */
+#define DCA_TAG_MAP_VALID 0x80
+
+#define DCA3_TAG_MAP_BIT_TO_INV 0x80
+#define DCA3_TAG_MAP_BIT_TO_SEL 0x40
+#define DCA3_TAG_MAP_LITERAL_VAL 0x1
+
+#define DCA_TAG_MAP_MASK 0xDF
+
+/* expected tag map bytes for I/OAT ver.2 */
+#define DCA2_TAG_MAP_BYTE0 0x80
+#define DCA2_TAG_MAP_BYTE1 0x0
+#define DCA2_TAG_MAP_BYTE2 0x81
+#define DCA2_TAG_MAP_BYTE3 0x82
+#define DCA2_TAG_MAP_BYTE4 0x82
+
+/* verify if tag map matches expected values */
+static inline int dca2_tag_map_valid(u8 *tag_map)
+{
+ return ((tag_map[0] == DCA2_TAG_MAP_BYTE0) &&
+ (tag_map[1] == DCA2_TAG_MAP_BYTE1) &&
+ (tag_map[2] == DCA2_TAG_MAP_BYTE2) &&
+ (tag_map[3] == DCA2_TAG_MAP_BYTE3) &&
+ (tag_map[4] == DCA2_TAG_MAP_BYTE4));
+}
+
+/*
+ * "Legacy" DCA systems do not implement the DCA register set in the
+ * I/OAT device. Software needs direct support for their tag mappings.
+ */
+
+#define APICID_BIT(x) (DCA_TAG_MAP_VALID | (x))
+#define IOAT_TAG_MAP_LEN 8
+
+static u8 ioat_tag_map_BNB[IOAT_TAG_MAP_LEN] = {
+ 1, APICID_BIT(1), APICID_BIT(2), APICID_BIT(2), };
+static u8 ioat_tag_map_SCNB[IOAT_TAG_MAP_LEN] = {
+ 1, APICID_BIT(1), APICID_BIT(2), APICID_BIT(2), };
+static u8 ioat_tag_map_CNB[IOAT_TAG_MAP_LEN] = {
+ 1, APICID_BIT(1), APICID_BIT(3), APICID_BIT(4), APICID_BIT(2), };
+static u8 ioat_tag_map_UNISYS[IOAT_TAG_MAP_LEN] = { 0 };
+
+/* pack PCI B/D/F into a u16 */
+static inline u16 dcaid_from_pcidev(struct pci_dev *pci)
+{
+ return (pci->bus->number << 8) | pci->devfn;
+}
+
+static int dca_enabled_in_bios(struct pci_dev *pdev)
+{
+ /* CPUID level 9 returns DCA configuration */
+ /* Bit 0 indicates DCA enabled by the BIOS */
+ unsigned long cpuid_level_9;
+ int res;
+
+ cpuid_level_9 = cpuid_eax(9);
+ res = test_bit(0, &cpuid_level_9);
+ if (!res)
+ dev_err(&pdev->dev, "DCA is disabled in BIOS\n");
+
+ return res;
+}
+
+static int system_has_dca_enabled(struct pci_dev *pdev)
+{
+ if (boot_cpu_has(X86_FEATURE_DCA))
+ return dca_enabled_in_bios(pdev);
+
+ dev_err(&pdev->dev, "boot cpu doesn't have X86_FEATURE_DCA\n");
+ return 0;
+}
+
+struct ioat_dca_slot {
+ struct pci_dev *pdev; /* requester device */
+ u16 rid; /* requester id, as used by IOAT */
+};
+
+#define IOAT_DCA_MAX_REQ 6
+#define IOAT3_DCA_MAX_REQ 2
+
+struct ioat_dca_priv {
+ void __iomem *iobase;
+ void __iomem *dca_base;
+ int max_requesters;
+ int requester_count;
+ u8 tag_map[IOAT_TAG_MAP_LEN];
+ struct ioat_dca_slot req_slots[0];
+};
+
+/* 5000 series chipset DCA Port Requester ID Table Entry Format
+ * [15:8] PCI-Express Bus Number
+ * [7:3] PCI-Express Device Number
+ * [2:0] PCI-Express Function Number
+ *
+ * 5000 series chipset DCA control register format
+ * [7:1] Reserved (0)
+ * [0] Ignore Function Number
+ */
+
+static int ioat_dca_add_requester(struct dca_provider *dca, struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+ u16 id;
+
+ /* This implementation only supports PCI-Express */
+ if (dev->bus != &pci_bus_type)
+ return -ENODEV;
+ pdev = to_pci_dev(dev);
+ id = dcaid_from_pcidev(pdev);
+
+ if (ioatdca->requester_count == ioatdca->max_requesters)
+ return -ENODEV;
+
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == NULL) {
+ /* found an empty slot */
+ ioatdca->requester_count++;
+ ioatdca->req_slots[i].pdev = pdev;
+ ioatdca->req_slots[i].rid = id;
+ writew(id, ioatdca->dca_base + (i * 4));
+ /* make sure the ignore function bit is off */
+ writeb(0, ioatdca->dca_base + (i * 4) + 2);
+ return i;
+ }
+ }
+ /* Error, ioatdma->requester_count is out of whack */
+ return -EFAULT;
+}
+
+static int ioat_dca_remove_requester(struct dca_provider *dca,
+ struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+
+ /* This implementation only supports PCI-Express */
+ if (dev->bus != &pci_bus_type)
+ return -ENODEV;
+ pdev = to_pci_dev(dev);
+
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == pdev) {
+ writew(0, ioatdca->dca_base + (i * 4));
+ ioatdca->req_slots[i].pdev = NULL;
+ ioatdca->req_slots[i].rid = 0;
+ ioatdca->requester_count--;
+ return i;
+ }
+ }
+ return -ENODEV;
+}
+
+static u8 ioat_dca_get_tag(struct dca_provider *dca,
+ struct device *dev,
+ int cpu)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ int i, apic_id, bit, value;
+ u8 entry, tag;
+
+ tag = 0;
+ apic_id = cpu_physical_id(cpu);
+
+ for (i = 0; i < IOAT_TAG_MAP_LEN; i++) {
+ entry = ioatdca->tag_map[i];
+ if (entry & DCA_TAG_MAP_VALID) {
+ bit = entry & ~DCA_TAG_MAP_VALID;
+ value = (apic_id & (1 << bit)) ? 1 : 0;
+ } else {
+ value = entry ? 1 : 0;
+ }
+ tag |= (value << i);
+ }
+ return tag;
+}
+
+static int ioat_dca_dev_managed(struct dca_provider *dca,
+ struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+
+ pdev = to_pci_dev(dev);
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == pdev)
+ return 1;
+ }
+ return 0;
+}
+
+static struct dca_ops ioat_dca_ops = {
+ .add_requester = ioat_dca_add_requester,
+ .remove_requester = ioat_dca_remove_requester,
+ .get_tag = ioat_dca_get_tag,
+ .dev_managed = ioat_dca_dev_managed,
+};
+
+
+struct dca_provider * __devinit
+ioat_dca_init(struct pci_dev *pdev, void __iomem *iobase)
+{
+ struct dca_provider *dca;
+ struct ioat_dca_priv *ioatdca;
+ u8 *tag_map = NULL;
+ int i;
+ int err;
+ u8 version;
+ u8 max_requesters;
+
+ if (!system_has_dca_enabled(pdev))
+ return NULL;
+
+ /* I/OAT v1 systems must have a known tag_map to support DCA */
+ switch (pdev->vendor) {
+ case PCI_VENDOR_ID_INTEL:
+ switch (pdev->device) {
+ case PCI_DEVICE_ID_INTEL_IOAT:
+ tag_map = ioat_tag_map_BNB;
+ break;
+ case PCI_DEVICE_ID_INTEL_IOAT_CNB:
+ tag_map = ioat_tag_map_CNB;
+ break;
+ case PCI_DEVICE_ID_INTEL_IOAT_SCNB:
+ tag_map = ioat_tag_map_SCNB;
+ break;
+ }
+ break;
+ case PCI_VENDOR_ID_UNISYS:
+ switch (pdev->device) {
+ case PCI_DEVICE_ID_UNISYS_DMA_DIRECTOR:
+ tag_map = ioat_tag_map_UNISYS;
+ break;
+ }
+ break;
+ }
+ if (tag_map == NULL)
+ return NULL;
+
+ version = readb(iobase + IOAT_VER_OFFSET);
+ if (version == IOAT_VER_3_0)
+ max_requesters = IOAT3_DCA_MAX_REQ;
+ else
+ max_requesters = IOAT_DCA_MAX_REQ;
+
+ dca = alloc_dca_provider(&ioat_dca_ops,
+ sizeof(*ioatdca) +
+ (sizeof(struct ioat_dca_slot) * max_requesters));
+ if (!dca)
+ return NULL;
+
+ ioatdca = dca_priv(dca);
+ ioatdca->max_requesters = max_requesters;
+ ioatdca->dca_base = iobase + 0x54;
+
+ /* copy over the APIC ID to DCA tag mapping */
+ for (i = 0; i < IOAT_TAG_MAP_LEN; i++)
+ ioatdca->tag_map[i] = tag_map[i];
+
+ err = register_dca_provider(dca, &pdev->dev);
+ if (err) {
+ free_dca_provider(dca);
+ return NULL;
+ }
+
+ return dca;
+}
+
+
+static int ioat2_dca_add_requester(struct dca_provider *dca, struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+ u16 id;
+ u16 global_req_table;
+
+ /* This implementation only supports PCI-Express */
+ if (dev->bus != &pci_bus_type)
+ return -ENODEV;
+ pdev = to_pci_dev(dev);
+ id = dcaid_from_pcidev(pdev);
+
+ if (ioatdca->requester_count == ioatdca->max_requesters)
+ return -ENODEV;
+
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == NULL) {
+ /* found an empty slot */
+ ioatdca->requester_count++;
+ ioatdca->req_slots[i].pdev = pdev;
+ ioatdca->req_slots[i].rid = id;
+ global_req_table =
+ readw(ioatdca->dca_base + IOAT_DCA_GREQID_OFFSET);
+ writel(id | IOAT_DCA_GREQID_VALID,
+ ioatdca->iobase + global_req_table + (i * 4));
+ return i;
+ }
+ }
+ /* Error, ioatdma->requester_count is out of whack */
+ return -EFAULT;
+}
+
+static int ioat2_dca_remove_requester(struct dca_provider *dca,
+ struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+ u16 global_req_table;
+
+ /* This implementation only supports PCI-Express */
+ if (dev->bus != &pci_bus_type)
+ return -ENODEV;
+ pdev = to_pci_dev(dev);
+
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == pdev) {
+ global_req_table =
+ readw(ioatdca->dca_base + IOAT_DCA_GREQID_OFFSET);
+ writel(0, ioatdca->iobase + global_req_table + (i * 4));
+ ioatdca->req_slots[i].pdev = NULL;
+ ioatdca->req_slots[i].rid = 0;
+ ioatdca->requester_count--;
+ return i;
+ }
+ }
+ return -ENODEV;
+}
+
+static u8 ioat2_dca_get_tag(struct dca_provider *dca,
+ struct device *dev,
+ int cpu)
+{
+ u8 tag;
+
+ tag = ioat_dca_get_tag(dca, dev, cpu);
+ tag = (~tag) & 0x1F;
+ return tag;
+}
+
+static struct dca_ops ioat2_dca_ops = {
+ .add_requester = ioat2_dca_add_requester,
+ .remove_requester = ioat2_dca_remove_requester,
+ .get_tag = ioat2_dca_get_tag,
+ .dev_managed = ioat_dca_dev_managed,
+};
+
+static int ioat2_dca_count_dca_slots(void __iomem *iobase, u16 dca_offset)
+{
+ int slots = 0;
+ u32 req;
+ u16 global_req_table;
+
+ global_req_table = readw(iobase + dca_offset + IOAT_DCA_GREQID_OFFSET);
+ if (global_req_table == 0)
+ return 0;
+ do {
+ req = readl(iobase + global_req_table + (slots * sizeof(u32)));
+ slots++;
+ } while ((req & IOAT_DCA_GREQID_LASTID) == 0);
+
+ return slots;
+}
+
+struct dca_provider * __devinit
+ioat2_dca_init(struct pci_dev *pdev, void __iomem *iobase)
+{
+ struct dca_provider *dca;
+ struct ioat_dca_priv *ioatdca;
+ int slots;
+ int i;
+ int err;
+ u32 tag_map;
+ u16 dca_offset;
+ u16 csi_fsb_control;
+ u16 pcie_control;
+ u8 bit;
+
+ if (!system_has_dca_enabled(pdev))
+ return NULL;
+
+ dca_offset = readw(iobase + IOAT_DCAOFFSET_OFFSET);
+ if (dca_offset == 0)
+ return NULL;
+
+ slots = ioat2_dca_count_dca_slots(iobase, dca_offset);
+ if (slots == 0)
+ return NULL;
+
+ dca = alloc_dca_provider(&ioat2_dca_ops,
+ sizeof(*ioatdca)
+ + (sizeof(struct ioat_dca_slot) * slots));
+ if (!dca)
+ return NULL;
+
+ ioatdca = dca_priv(dca);
+ ioatdca->iobase = iobase;
+ ioatdca->dca_base = iobase + dca_offset;
+ ioatdca->max_requesters = slots;
+
+ /* some bios might not know to turn these on */
+ csi_fsb_control = readw(ioatdca->dca_base + IOAT_FSB_CAP_ENABLE_OFFSET);
+ if ((csi_fsb_control & IOAT_FSB_CAP_ENABLE_PREFETCH) == 0) {
+ csi_fsb_control |= IOAT_FSB_CAP_ENABLE_PREFETCH;
+ writew(csi_fsb_control,
+ ioatdca->dca_base + IOAT_FSB_CAP_ENABLE_OFFSET);
+ }
+ pcie_control = readw(ioatdca->dca_base + IOAT_PCI_CAP_ENABLE_OFFSET);
+ if ((pcie_control & IOAT_PCI_CAP_ENABLE_MEMWR) == 0) {
+ pcie_control |= IOAT_PCI_CAP_ENABLE_MEMWR;
+ writew(pcie_control,
+ ioatdca->dca_base + IOAT_PCI_CAP_ENABLE_OFFSET);
+ }
+
+
+ /* TODO version, compatibility and configuration checks */
+
+ /* copy out the APIC to DCA tag map */
+ tag_map = readl(ioatdca->dca_base + IOAT_APICID_TAG_MAP_OFFSET);
+ for (i = 0; i < 5; i++) {
+ bit = (tag_map >> (4 * i)) & 0x0f;
+ if (bit < 8)
+ ioatdca->tag_map[i] = bit | DCA_TAG_MAP_VALID;
+ else
+ ioatdca->tag_map[i] = 0;
+ }
+
+ if (!dca2_tag_map_valid(ioatdca->tag_map)) {
+ dev_err(&pdev->dev, "APICID_TAG_MAP set incorrectly by BIOS, "
+ "disabling DCA\n");
+ free_dca_provider(dca);
+ return NULL;
+ }
+
+ err = register_dca_provider(dca, &pdev->dev);
+ if (err) {
+ free_dca_provider(dca);
+ return NULL;
+ }
+
+ return dca;
+}
+
+static int ioat3_dca_add_requester(struct dca_provider *dca, struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+ u16 id;
+ u16 global_req_table;
+
+ /* This implementation only supports PCI-Express */
+ if (dev->bus != &pci_bus_type)
+ return -ENODEV;
+ pdev = to_pci_dev(dev);
+ id = dcaid_from_pcidev(pdev);
+
+ if (ioatdca->requester_count == ioatdca->max_requesters)
+ return -ENODEV;
+
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == NULL) {
+ /* found an empty slot */
+ ioatdca->requester_count++;
+ ioatdca->req_slots[i].pdev = pdev;
+ ioatdca->req_slots[i].rid = id;
+ global_req_table =
+ readw(ioatdca->dca_base + IOAT3_DCA_GREQID_OFFSET);
+ writel(id | IOAT_DCA_GREQID_VALID,
+ ioatdca->iobase + global_req_table + (i * 4));
+ return i;
+ }
+ }
+ /* Error, ioatdma->requester_count is out of whack */
+ return -EFAULT;
+}
+
+static int ioat3_dca_remove_requester(struct dca_provider *dca,
+ struct device *dev)
+{
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ struct pci_dev *pdev;
+ int i;
+ u16 global_req_table;
+
+ /* This implementation only supports PCI-Express */
+ if (dev->bus != &pci_bus_type)
+ return -ENODEV;
+ pdev = to_pci_dev(dev);
+
+ for (i = 0; i < ioatdca->max_requesters; i++) {
+ if (ioatdca->req_slots[i].pdev == pdev) {
+ global_req_table =
+ readw(ioatdca->dca_base + IOAT3_DCA_GREQID_OFFSET);
+ writel(0, ioatdca->iobase + global_req_table + (i * 4));
+ ioatdca->req_slots[i].pdev = NULL;
+ ioatdca->req_slots[i].rid = 0;
+ ioatdca->requester_count--;
+ return i;
+ }
+ }
+ return -ENODEV;
+}
+
+static u8 ioat3_dca_get_tag(struct dca_provider *dca,
+ struct device *dev,
+ int cpu)
+{
+ u8 tag;
+
+ struct ioat_dca_priv *ioatdca = dca_priv(dca);
+ int i, apic_id, bit, value;
+ u8 entry;
+
+ tag = 0;
+ apic_id = cpu_physical_id(cpu);
+
+ for (i = 0; i < IOAT_TAG_MAP_LEN; i++) {
+ entry = ioatdca->tag_map[i];
+ if (entry & DCA3_TAG_MAP_BIT_TO_SEL) {
+ bit = entry &
+ ~(DCA3_TAG_MAP_BIT_TO_SEL | DCA3_TAG_MAP_BIT_TO_INV);
+ value = (apic_id & (1 << bit)) ? 1 : 0;
+ } else if (entry & DCA3_TAG_MAP_BIT_TO_INV) {
+ bit = entry & ~DCA3_TAG_MAP_BIT_TO_INV;
+ value = (apic_id & (1 << bit)) ? 0 : 1;
+ } else {
+ value = (entry & DCA3_TAG_MAP_LITERAL_VAL) ? 1 : 0;
+ }
+ tag |= (value << i);
+ }
+
+ return tag;
+}
+
+static struct dca_ops ioat3_dca_ops = {
+ .add_requester = ioat3_dca_add_requester,
+ .remove_requester = ioat3_dca_remove_requester,
+ .get_tag = ioat3_dca_get_tag,
+ .dev_managed = ioat_dca_dev_managed,
+};
+
+static int ioat3_dca_count_dca_slots(void *iobase, u16 dca_offset)
+{
+ int slots = 0;
+ u32 req;
+ u16 global_req_table;
+
+ global_req_table = readw(iobase + dca_offset + IOAT3_DCA_GREQID_OFFSET);
+ if (global_req_table == 0)
+ return 0;
+
+ do {
+ req = readl(iobase + global_req_table + (slots * sizeof(u32)));
+ slots++;
+ } while ((req & IOAT_DCA_GREQID_LASTID) == 0);
+
+ return slots;
+}
+
+struct dca_provider * __devinit
+ioat3_dca_init(struct pci_dev *pdev, void __iomem *iobase)
+{
+ struct dca_provider *dca;
+ struct ioat_dca_priv *ioatdca;
+ int slots;
+ int i;
+ int err;
+ u16 dca_offset;
+ u16 csi_fsb_control;
+ u16 pcie_control;
+ u8 bit;
+
+ union {
+ u64 full;
+ struct {
+ u32 low;
+ u32 high;
+ };
+ } tag_map;
+
+ if (!system_has_dca_enabled(pdev))
+ return NULL;
+
+ dca_offset = readw(iobase + IOAT_DCAOFFSET_OFFSET);
+ if (dca_offset == 0)
+ return NULL;
+
+ slots = ioat3_dca_count_dca_slots(iobase, dca_offset);
+ if (slots == 0)
+ return NULL;
+
+ dca = alloc_dca_provider(&ioat3_dca_ops,
+ sizeof(*ioatdca)
+ + (sizeof(struct ioat_dca_slot) * slots));
+ if (!dca)
+ return NULL;
+
+ ioatdca = dca_priv(dca);
+ ioatdca->iobase = iobase;
+ ioatdca->dca_base = iobase + dca_offset;
+ ioatdca->max_requesters = slots;
+
+ /* some bios might not know to turn these on */
+ csi_fsb_control = readw(ioatdca->dca_base + IOAT3_CSI_CONTROL_OFFSET);
+ if ((csi_fsb_control & IOAT3_CSI_CONTROL_PREFETCH) == 0) {
+ csi_fsb_control |= IOAT3_CSI_CONTROL_PREFETCH;
+ writew(csi_fsb_control,
+ ioatdca->dca_base + IOAT3_CSI_CONTROL_OFFSET);
+ }
+ pcie_control = readw(ioatdca->dca_base + IOAT3_PCI_CONTROL_OFFSET);
+ if ((pcie_control & IOAT3_PCI_CONTROL_MEMWR) == 0) {
+ pcie_control |= IOAT3_PCI_CONTROL_MEMWR;
+ writew(pcie_control,
+ ioatdca->dca_base + IOAT3_PCI_CONTROL_OFFSET);
+ }
+
+
+ /* TODO version, compatibility and configuration checks */
+
+ /* copy out the APIC to DCA tag map */
+ tag_map.low =
+ readl(ioatdca->dca_base + IOAT3_APICID_TAG_MAP_OFFSET_LOW);
+ tag_map.high =
+ readl(ioatdca->dca_base + IOAT3_APICID_TAG_MAP_OFFSET_HIGH);
+ for (i = 0; i < 8; i++) {
+ bit = tag_map.full >> (8 * i);
+ ioatdca->tag_map[i] = bit & DCA_TAG_MAP_MASK;
+ }
+
+ err = register_dca_provider(dca, &pdev->dev);
+ if (err) {
+ free_dca_provider(dca);
+ return NULL;
+ }
+
+ return dca;
+}
--- /dev/null
+/*
+ * Intel I/OAT DMA Linux driver
+ * Copyright(c) 2004 - 2009 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ *
+ */
+
+/*
+ * This driver supports an Intel I/OAT DMA engine, which does asynchronous
+ * copy operations.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/dmaengine.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/workqueue.h>
+#include <linux/i7300_idle.h>
+#include "dma.h"
+#include "registers.h"
+#include "hw.h"
+
+int ioat_pending_level = 4;
+module_param(ioat_pending_level, int, 0644);
+MODULE_PARM_DESC(ioat_pending_level,
+ "high-water mark for pushing ioat descriptors (default: 4)");
+
+/* internal functions */
+static void ioat1_cleanup(struct ioat_dma_chan *ioat);
+static void ioat1_dma_start_null_desc(struct ioat_dma_chan *ioat);
+
+/**
+ * ioat_dma_do_interrupt - handler used for single vector interrupt mode
+ * @irq: interrupt id
+ * @data: interrupt data
+ */
+static irqreturn_t ioat_dma_do_interrupt(int irq, void *data)
+{
+ struct ioatdma_device *instance = data;
+ struct ioat_chan_common *chan;
+ unsigned long attnstatus;
+ int bit;
+ u8 intrctrl;
+
+ intrctrl = readb(instance->reg_base + IOAT_INTRCTRL_OFFSET);
+
+ if (!(intrctrl & IOAT_INTRCTRL_MASTER_INT_EN))
+ return IRQ_NONE;
+
+ if (!(intrctrl & IOAT_INTRCTRL_INT_STATUS)) {
+ writeb(intrctrl, instance->reg_base + IOAT_INTRCTRL_OFFSET);
+ return IRQ_NONE;
+ }
+
+ attnstatus = readl(instance->reg_base + IOAT_ATTNSTATUS_OFFSET);
+ for_each_bit(bit, &attnstatus, BITS_PER_LONG) {
+ chan = ioat_chan_by_index(instance, bit);
+ tasklet_schedule(&chan->cleanup_task);
+ }
+
+ writeb(intrctrl, instance->reg_base + IOAT_INTRCTRL_OFFSET);
+ return IRQ_HANDLED;
+}
+
+/**
+ * ioat_dma_do_interrupt_msix - handler used for vector-per-channel interrupt mode
+ * @irq: interrupt id
+ * @data: interrupt data
+ */
+static irqreturn_t ioat_dma_do_interrupt_msix(int irq, void *data)
+{
+ struct ioat_chan_common *chan = data;
+
+ tasklet_schedule(&chan->cleanup_task);
+
+ return IRQ_HANDLED;
+}
+
+static void ioat1_cleanup_tasklet(unsigned long data);
+
+/* common channel initialization */
+void ioat_init_channel(struct ioatdma_device *device,
+ struct ioat_chan_common *chan, int idx,
+ void (*timer_fn)(unsigned long),
+ void (*tasklet)(unsigned long),
+ unsigned long ioat)
+{
+ struct dma_device *dma = &device->common;
+
+ chan->device = device;
+ chan->reg_base = device->reg_base + (0x80 * (idx + 1));
+ spin_lock_init(&chan->cleanup_lock);
+ chan->common.device = dma;
+ list_add_tail(&chan->common.device_node, &dma->channels);
+ device->idx[idx] = chan;
+ init_timer(&chan->timer);
+ chan->timer.function = timer_fn;
+ chan->timer.data = ioat;
+ tasklet_init(&chan->cleanup_task, tasklet, ioat);
+ tasklet_disable(&chan->cleanup_task);
+}
+
+static void ioat1_timer_event(unsigned long data);
+
+/**
+ * ioat1_dma_enumerate_channels - find and initialize the device's channels
+ * @device: the device to be enumerated
+ */
+static int ioat1_enumerate_channels(struct ioatdma_device *device)
+{
+ u8 xfercap_scale;
+ u32 xfercap;
+ int i;
+ struct ioat_dma_chan *ioat;
+ struct device *dev = &device->pdev->dev;
+ struct dma_device *dma = &device->common;
+
+ INIT_LIST_HEAD(&dma->channels);
+ dma->chancnt = readb(device->reg_base + IOAT_CHANCNT_OFFSET);
+ dma->chancnt &= 0x1f; /* bits [4:0] valid */
+ if (dma->chancnt > ARRAY_SIZE(device->idx)) {
+ dev_warn(dev, "(%d) exceeds max supported channels (%zu)\n",
+ dma->chancnt, ARRAY_SIZE(device->idx));
+ dma->chancnt = ARRAY_SIZE(device->idx);
+ }
+ xfercap_scale = readb(device->reg_base + IOAT_XFERCAP_OFFSET);
+ xfercap_scale &= 0x1f; /* bits [4:0] valid */
+ xfercap = (xfercap_scale == 0 ? -1 : (1UL << xfercap_scale));
+ dev_dbg(dev, "%s: xfercap = %d\n", __func__, xfercap);
+
+#ifdef CONFIG_I7300_IDLE_IOAT_CHANNEL
+ if (i7300_idle_platform_probe(NULL, NULL, 1) == 0)
+ dma->chancnt--;
+#endif
+ for (i = 0; i < dma->chancnt; i++) {
+ ioat = devm_kzalloc(dev, sizeof(*ioat), GFP_KERNEL);
+ if (!ioat)
+ break;
+
+ ioat_init_channel(device, &ioat->base, i,
+ ioat1_timer_event,
+ ioat1_cleanup_tasklet,
+ (unsigned long) ioat);
+ ioat->xfercap = xfercap;
+ spin_lock_init(&ioat->desc_lock);
+ INIT_LIST_HEAD(&ioat->free_desc);
+ INIT_LIST_HEAD(&ioat->used_desc);
+ }
+ dma->chancnt = i;
+ return i;
+}
+
+/**
+ * ioat_dma_memcpy_issue_pending - push potentially unrecognized appended
+ * descriptors to hw
+ * @chan: DMA channel handle
+ */
+static inline void
+__ioat1_dma_memcpy_issue_pending(struct ioat_dma_chan *ioat)
+{
+ void __iomem *reg_base = ioat->base.reg_base;
+
+ dev_dbg(to_dev(&ioat->base), "%s: pending: %d\n",
+ __func__, ioat->pending);
+ ioat->pending = 0;
+ writeb(IOAT_CHANCMD_APPEND, reg_base + IOAT1_CHANCMD_OFFSET);
+}
+
+static void ioat1_dma_memcpy_issue_pending(struct dma_chan *chan)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(chan);
+
+ if (ioat->pending > 0) {
+ spin_lock_bh(&ioat->desc_lock);
+ __ioat1_dma_memcpy_issue_pending(ioat);
+ spin_unlock_bh(&ioat->desc_lock);
+ }
+}
+
+/**
+ * ioat1_reset_channel - restart a channel
+ * @ioat: IOAT DMA channel handle
+ */
+static void ioat1_reset_channel(struct ioat_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ void __iomem *reg_base = chan->reg_base;
+ u32 chansts, chanerr;
+
+ dev_warn(to_dev(chan), "reset\n");
+ chanerr = readl(reg_base + IOAT_CHANERR_OFFSET);
+ chansts = *chan->completion & IOAT_CHANSTS_STATUS;
+ if (chanerr) {
+ dev_err(to_dev(chan),
+ "chan%d, CHANSTS = 0x%08x CHANERR = 0x%04x, clearing\n",
+ chan_num(chan), chansts, chanerr);
+ writel(chanerr, reg_base + IOAT_CHANERR_OFFSET);
+ }
+
+ /*
+ * whack it upside the head with a reset
+ * and wait for things to settle out.
+ * force the pending count to a really big negative
+ * to make sure no one forces an issue_pending
+ * while we're waiting.
+ */
+
+ ioat->pending = INT_MIN;
+ writeb(IOAT_CHANCMD_RESET,
+ reg_base + IOAT_CHANCMD_OFFSET(chan->device->version));
+ set_bit(IOAT_RESET_PENDING, &chan->state);
+ mod_timer(&chan->timer, jiffies + RESET_DELAY);
+}
+
+static dma_cookie_t ioat1_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+ struct dma_chan *c = tx->chan;
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+ struct ioat_desc_sw *desc = tx_to_ioat_desc(tx);
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioat_desc_sw *first;
+ struct ioat_desc_sw *chain_tail;
+ dma_cookie_t cookie;
+
+ spin_lock_bh(&ioat->desc_lock);
+ /* cookie incr and addition to used_list must be atomic */
+ cookie = c->cookie;
+ cookie++;
+ if (cookie < 0)
+ cookie = 1;
+ c->cookie = cookie;
+ tx->cookie = cookie;
+ dev_dbg(to_dev(&ioat->base), "%s: cookie: %d\n", __func__, cookie);
+
+ /* write address into NextDescriptor field of last desc in chain */
+ first = to_ioat_desc(desc->tx_list.next);
+ chain_tail = to_ioat_desc(ioat->used_desc.prev);
+ /* make descriptor updates globally visible before chaining */
+ wmb();
+ chain_tail->hw->next = first->txd.phys;
+ list_splice_tail_init(&desc->tx_list, &ioat->used_desc);
+ dump_desc_dbg(ioat, chain_tail);
+ dump_desc_dbg(ioat, first);
+
+ if (!test_and_set_bit(IOAT_COMPLETION_PENDING, &chan->state))
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+
+ ioat->active += desc->hw->tx_cnt;
+ ioat->pending += desc->hw->tx_cnt;
+ if (ioat->pending >= ioat_pending_level)
+ __ioat1_dma_memcpy_issue_pending(ioat);
+ spin_unlock_bh(&ioat->desc_lock);
+
+ return cookie;
+}
+
+/**
+ * ioat_dma_alloc_descriptor - allocate and return a sw and hw descriptor pair
+ * @ioat: the channel supplying the memory pool for the descriptors
+ * @flags: allocation flags
+ */
+static struct ioat_desc_sw *
+ioat_dma_alloc_descriptor(struct ioat_dma_chan *ioat, gfp_t flags)
+{
+ struct ioat_dma_descriptor *desc;
+ struct ioat_desc_sw *desc_sw;
+ struct ioatdma_device *ioatdma_device;
+ dma_addr_t phys;
+
+ ioatdma_device = ioat->base.device;
+ desc = pci_pool_alloc(ioatdma_device->dma_pool, flags, &phys);
+ if (unlikely(!desc))
+ return NULL;
+
+ desc_sw = kzalloc(sizeof(*desc_sw), flags);
+ if (unlikely(!desc_sw)) {
+ pci_pool_free(ioatdma_device->dma_pool, desc, phys);
+ return NULL;
+ }
+
+ memset(desc, 0, sizeof(*desc));
+
+ INIT_LIST_HEAD(&desc_sw->tx_list);
+ dma_async_tx_descriptor_init(&desc_sw->txd, &ioat->base.common);
+ desc_sw->txd.tx_submit = ioat1_tx_submit;
+ desc_sw->hw = desc;
+ desc_sw->txd.phys = phys;
+ set_desc_id(desc_sw, -1);
+
+ return desc_sw;
+}
+
+static int ioat_initial_desc_count = 256;
+module_param(ioat_initial_desc_count, int, 0644);
+MODULE_PARM_DESC(ioat_initial_desc_count,
+ "ioat1: initial descriptors per channel (default: 256)");
+/**
+ * ioat1_dma_alloc_chan_resources - returns the number of allocated descriptors
+ * @chan: the channel to be filled out
+ */
+static int ioat1_dma_alloc_chan_resources(struct dma_chan *c)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioat_desc_sw *desc;
+ u32 chanerr;
+ int i;
+ LIST_HEAD(tmp_list);
+
+ /* have we already been set up? */
+ if (!list_empty(&ioat->free_desc))
+ return ioat->desccount;
+
+ /* Setup register to interrupt and write completion status on error */
+ writew(IOAT_CHANCTRL_RUN, chan->reg_base + IOAT_CHANCTRL_OFFSET);
+
+ chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ if (chanerr) {
+ dev_err(to_dev(chan), "CHANERR = %x, clearing\n", chanerr);
+ writel(chanerr, chan->reg_base + IOAT_CHANERR_OFFSET);
+ }
+
+ /* Allocate descriptors */
+ for (i = 0; i < ioat_initial_desc_count; i++) {
+ desc = ioat_dma_alloc_descriptor(ioat, GFP_KERNEL);
+ if (!desc) {
+ dev_err(to_dev(chan), "Only %d initial descriptors\n", i);
+ break;
+ }
+ set_desc_id(desc, i);
+ list_add_tail(&desc->node, &tmp_list);
+ }
+ spin_lock_bh(&ioat->desc_lock);
+ ioat->desccount = i;
+ list_splice(&tmp_list, &ioat->free_desc);
+ spin_unlock_bh(&ioat->desc_lock);
+
+ /* allocate a completion writeback area */
+ /* doing 2 32bit writes to mmio since 1 64b write doesn't work */
+ chan->completion = pci_pool_alloc(chan->device->completion_pool,
+ GFP_KERNEL, &chan->completion_dma);
+ memset(chan->completion, 0, sizeof(*chan->completion));
+ writel(((u64) chan->completion_dma) & 0x00000000FFFFFFFF,
+ chan->reg_base + IOAT_CHANCMP_OFFSET_LOW);
+ writel(((u64) chan->completion_dma) >> 32,
+ chan->reg_base + IOAT_CHANCMP_OFFSET_HIGH);
+
+ tasklet_enable(&chan->cleanup_task);
+ ioat1_dma_start_null_desc(ioat); /* give chain to dma device */
+ dev_dbg(to_dev(chan), "%s: allocated %d descriptors\n",
+ __func__, ioat->desccount);
+ return ioat->desccount;
+}
+
+/**
+ * ioat1_dma_free_chan_resources - release all the descriptors
+ * @chan: the channel to be cleaned
+ */
+static void ioat1_dma_free_chan_resources(struct dma_chan *c)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioatdma_device *ioatdma_device = chan->device;
+ struct ioat_desc_sw *desc, *_desc;
+ int in_use_descs = 0;
+
+ /* Before freeing channel resources first check
+ * if they have been previously allocated for this channel.
+ */
+ if (ioat->desccount == 0)
+ return;
+
+ tasklet_disable(&chan->cleanup_task);
+ del_timer_sync(&chan->timer);
+ ioat1_cleanup(ioat);
+
+ /* Delay 100ms after reset to allow internal DMA logic to quiesce
+ * before removing DMA descriptor resources.
+ */
+ writeb(IOAT_CHANCMD_RESET,
+ chan->reg_base + IOAT_CHANCMD_OFFSET(chan->device->version));
+ mdelay(100);
+
+ spin_lock_bh(&ioat->desc_lock);
+ list_for_each_entry_safe(desc, _desc, &ioat->used_desc, node) {
+ dev_dbg(to_dev(chan), "%s: freeing %d from used list\n",
+ __func__, desc_id(desc));
+ dump_desc_dbg(ioat, desc);
+ in_use_descs++;
+ list_del(&desc->node);
+ pci_pool_free(ioatdma_device->dma_pool, desc->hw,
+ desc->txd.phys);
+ kfree(desc);
+ }
+ list_for_each_entry_safe(desc, _desc,
+ &ioat->free_desc, node) {
+ list_del(&desc->node);
+ pci_pool_free(ioatdma_device->dma_pool, desc->hw,
+ desc->txd.phys);
+ kfree(desc);
+ }
+ spin_unlock_bh(&ioat->desc_lock);
+
+ pci_pool_free(ioatdma_device->completion_pool,
+ chan->completion,
+ chan->completion_dma);
+
+ /* one is ok since we left it on there on purpose */
+ if (in_use_descs > 1)
+ dev_err(to_dev(chan), "Freeing %d in use descriptors!\n",
+ in_use_descs - 1);
+
+ chan->last_completion = 0;
+ chan->completion_dma = 0;
+ ioat->pending = 0;
+ ioat->desccount = 0;
+}
+
+/**
+ * ioat1_dma_get_next_descriptor - return the next available descriptor
+ * @ioat: IOAT DMA channel handle
+ *
+ * Gets the next descriptor from the chain, and must be called with the
+ * channel's desc_lock held. Allocates more descriptors if the channel
+ * has run out.
+ */
+static struct ioat_desc_sw *
+ioat1_dma_get_next_descriptor(struct ioat_dma_chan *ioat)
+{
+ struct ioat_desc_sw *new;
+
+ if (!list_empty(&ioat->free_desc)) {
+ new = to_ioat_desc(ioat->free_desc.next);
+ list_del(&new->node);
+ } else {
+ /* try to get another desc */
+ new = ioat_dma_alloc_descriptor(ioat, GFP_ATOMIC);
+ if (!new) {
+ dev_err(to_dev(&ioat->base), "alloc failed\n");
+ return NULL;
+ }
+ }
+ dev_dbg(to_dev(&ioat->base), "%s: allocated: %d\n",
+ __func__, desc_id(new));
+ prefetch(new->hw);
+ return new;
+}
+
+static struct dma_async_tx_descriptor *
+ioat1_dma_prep_memcpy(struct dma_chan *c, dma_addr_t dma_dest,
+ dma_addr_t dma_src, size_t len, unsigned long flags)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+ struct ioat_desc_sw *desc;
+ size_t copy;
+ LIST_HEAD(chain);
+ dma_addr_t src = dma_src;
+ dma_addr_t dest = dma_dest;
+ size_t total_len = len;
+ struct ioat_dma_descriptor *hw = NULL;
+ int tx_cnt = 0;
+
+ spin_lock_bh(&ioat->desc_lock);
+ desc = ioat1_dma_get_next_descriptor(ioat);
+ do {
+ if (!desc)
+ break;
+
+ tx_cnt++;
+ copy = min_t(size_t, len, ioat->xfercap);
+
+ hw = desc->hw;
+ hw->size = copy;
+ hw->ctl = 0;
+ hw->src_addr = src;
+ hw->dst_addr = dest;
+
+ list_add_tail(&desc->node, &chain);
+
+ len -= copy;
+ dest += copy;
+ src += copy;
+ if (len) {
+ struct ioat_desc_sw *next;
+
+ async_tx_ack(&desc->txd);
+ next = ioat1_dma_get_next_descriptor(ioat);
+ hw->next = next ? next->txd.phys : 0;
+ dump_desc_dbg(ioat, desc);
+ desc = next;
+ } else
+ hw->next = 0;
+ } while (len);
+
+ if (!desc) {
+ struct ioat_chan_common *chan = &ioat->base;
+
+ dev_err(to_dev(chan),
+ "chan%d - get_next_desc failed\n", chan_num(chan));
+ list_splice(&chain, &ioat->free_desc);
+ spin_unlock_bh(&ioat->desc_lock);
+ return NULL;
+ }
+ spin_unlock_bh(&ioat->desc_lock);
+
+ desc->txd.flags = flags;
+ desc->len = total_len;
+ list_splice(&chain, &desc->tx_list);
+ hw->ctl_f.int_en = !!(flags & DMA_PREP_INTERRUPT);
+ hw->ctl_f.compl_write = 1;
+ hw->tx_cnt = tx_cnt;
+ dump_desc_dbg(ioat, desc);
+
+ return &desc->txd;
+}
+
+static void ioat1_cleanup_tasklet(unsigned long data)
+{
+ struct ioat_dma_chan *chan = (void *)data;
+
+ ioat1_cleanup(chan);
+ writew(IOAT_CHANCTRL_RUN, chan->base.reg_base + IOAT_CHANCTRL_OFFSET);
+}
+
+void ioat_dma_unmap(struct ioat_chan_common *chan, enum dma_ctrl_flags flags,
+ size_t len, struct ioat_dma_descriptor *hw)
+{
+ struct pci_dev *pdev = chan->device->pdev;
+ size_t offset = len - hw->size;
+
+ if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP))
+ ioat_unmap(pdev, hw->dst_addr - offset, len,
+ PCI_DMA_FROMDEVICE, flags, 1);
+
+ if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP))
+ ioat_unmap(pdev, hw->src_addr - offset, len,
+ PCI_DMA_TODEVICE, flags, 0);
+}
+
+unsigned long ioat_get_current_completion(struct ioat_chan_common *chan)
+{
+ unsigned long phys_complete;
+ u64 completion;
+
+ completion = *chan->completion;
+ phys_complete = ioat_chansts_to_addr(completion);
+
+ dev_dbg(to_dev(chan), "%s: phys_complete: %#llx\n", __func__,
+ (unsigned long long) phys_complete);
+
+ if (is_ioat_halted(completion)) {
+ u32 chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ dev_err(to_dev(chan), "Channel halted, chanerr = %x\n",
+ chanerr);
+
+ /* TODO do something to salvage the situation */
+ }
+
+ return phys_complete;
+}
+
+bool ioat_cleanup_preamble(struct ioat_chan_common *chan,
+ unsigned long *phys_complete)
+{
+ *phys_complete = ioat_get_current_completion(chan);
+ if (*phys_complete == chan->last_completion)
+ return false;
+ clear_bit(IOAT_COMPLETION_ACK, &chan->state);
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+
+ return true;
+}
+
+static void __cleanup(struct ioat_dma_chan *ioat, unsigned long phys_complete)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ struct list_head *_desc, *n;
+ struct dma_async_tx_descriptor *tx;
+
+ dev_dbg(to_dev(chan), "%s: phys_complete: %lx\n",
+ __func__, phys_complete);
+ list_for_each_safe(_desc, n, &ioat->used_desc) {
+ struct ioat_desc_sw *desc;
+
+ prefetch(n);
+ desc = list_entry(_desc, typeof(*desc), node);
+ tx = &desc->txd;
+ /*
+ * Incoming DMA requests may use multiple descriptors,
+ * due to exceeding xfercap, perhaps. If so, only the
+ * last one will have a cookie, and require unmapping.
+ */
+ dump_desc_dbg(ioat, desc);
+ if (tx->cookie) {
+ chan->completed_cookie = tx->cookie;
+ tx->cookie = 0;
+ ioat_dma_unmap(chan, tx->flags, desc->len, desc->hw);
+ ioat->active -= desc->hw->tx_cnt;
+ if (tx->callback) {
+ tx->callback(tx->callback_param);
+ tx->callback = NULL;
+ }
+ }
+
+ if (tx->phys != phys_complete) {
+ /*
+ * a completed entry, but not the last, so clean
+ * up if the client is done with the descriptor
+ */
+ if (async_tx_test_ack(tx))
+ list_move_tail(&desc->node, &ioat->free_desc);
+ } else {
+ /*
+ * last used desc. Do not remove, so we can
+ * append from it.
+ */
+
+ /* if nothing else is pending, cancel the
+ * completion timeout
+ */
+ if (n == &ioat->used_desc) {
+ dev_dbg(to_dev(chan),
+ "%s cancel completion timeout\n",
+ __func__);
+ clear_bit(IOAT_COMPLETION_PENDING, &chan->state);
+ }
+
+ /* TODO check status bits? */
+ break;
+ }
+ }
+
+ chan->last_completion = phys_complete;
+}
+
+/**
+ * ioat1_cleanup - cleanup up finished descriptors
+ * @chan: ioat channel to be cleaned up
+ *
+ * To prevent lock contention we defer cleanup when the locks are
+ * contended with a terminal timeout that forces cleanup and catches
+ * completion notification errors.
+ */
+static void ioat1_cleanup(struct ioat_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ unsigned long phys_complete;
+
+ prefetch(chan->completion);
+
+ if (!spin_trylock_bh(&chan->cleanup_lock))
+ return;
+
+ if (!ioat_cleanup_preamble(chan, &phys_complete)) {
+ spin_unlock_bh(&chan->cleanup_lock);
+ return;
+ }
+
+ if (!spin_trylock_bh(&ioat->desc_lock)) {
+ spin_unlock_bh(&chan->cleanup_lock);
+ return;
+ }
+
+ __cleanup(ioat, phys_complete);
+
+ spin_unlock_bh(&ioat->desc_lock);
+ spin_unlock_bh(&chan->cleanup_lock);
+}
+
+static void ioat1_timer_event(unsigned long data)
+{
+ struct ioat_dma_chan *ioat = (void *) data;
+ struct ioat_chan_common *chan = &ioat->base;
+
+ dev_dbg(to_dev(chan), "%s: state: %lx\n", __func__, chan->state);
+
+ spin_lock_bh(&chan->cleanup_lock);
+ if (test_and_clear_bit(IOAT_RESET_PENDING, &chan->state)) {
+ struct ioat_desc_sw *desc;
+
+ spin_lock_bh(&ioat->desc_lock);
+
+ /* restart active descriptors */
+ desc = to_ioat_desc(ioat->used_desc.prev);
+ ioat_set_chainaddr(ioat, desc->txd.phys);
+ ioat_start(chan);
+
+ ioat->pending = 0;
+ set_bit(IOAT_COMPLETION_PENDING, &chan->state);
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+ spin_unlock_bh(&ioat->desc_lock);
+ } else if (test_bit(IOAT_COMPLETION_PENDING, &chan->state)) {
+ unsigned long phys_complete;
+
+ spin_lock_bh(&ioat->desc_lock);
+ /* if we haven't made progress and we have already
+ * acknowledged a pending completion once, then be more
+ * forceful with a restart
+ */
+ if (ioat_cleanup_preamble(chan, &phys_complete))
+ __cleanup(ioat, phys_complete);
+ else if (test_bit(IOAT_COMPLETION_ACK, &chan->state))
+ ioat1_reset_channel(ioat);
+ else {
+ u64 status = ioat_chansts(chan);
+
+ /* manually update the last completion address */
+ if (ioat_chansts_to_addr(status) != 0)
+ *chan->completion = status;
+
+ set_bit(IOAT_COMPLETION_ACK, &chan->state);
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+ }
+ spin_unlock_bh(&ioat->desc_lock);
+ }
+ spin_unlock_bh(&chan->cleanup_lock);
+}
+
+static enum dma_status
+ioat1_dma_is_complete(struct dma_chan *c, dma_cookie_t cookie,
+ dma_cookie_t *done, dma_cookie_t *used)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+
+ if (ioat_is_complete(c, cookie, done, used) == DMA_SUCCESS)
+ return DMA_SUCCESS;
+
+ ioat1_cleanup(ioat);
+
+ return ioat_is_complete(c, cookie, done, used);
+}
+
+static void ioat1_dma_start_null_desc(struct ioat_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioat_desc_sw *desc;
+ struct ioat_dma_descriptor *hw;
+
+ spin_lock_bh(&ioat->desc_lock);
+
+ desc = ioat1_dma_get_next_descriptor(ioat);
+
+ if (!desc) {
+ dev_err(to_dev(chan),
+ "Unable to start null desc - get next desc failed\n");
+ spin_unlock_bh(&ioat->desc_lock);
+ return;
+ }
+
+ hw = desc->hw;
+ hw->ctl = 0;
+ hw->ctl_f.null = 1;
+ hw->ctl_f.int_en = 1;
+ hw->ctl_f.compl_write = 1;
+ /* set size to non-zero value (channel returns error when size is 0) */
+ hw->size = NULL_DESC_BUFFER_SIZE;
+ hw->src_addr = 0;
+ hw->dst_addr = 0;
+ async_tx_ack(&desc->txd);
+ hw->next = 0;
+ list_add_tail(&desc->node, &ioat->used_desc);
+ dump_desc_dbg(ioat, desc);
+
+ ioat_set_chainaddr(ioat, desc->txd.phys);
+ ioat_start(chan);
+ spin_unlock_bh(&ioat->desc_lock);
+}
+
+/*
+ * Perform a IOAT transaction to verify the HW works.
+ */
+#define IOAT_TEST_SIZE 2000
+
+static void __devinit ioat_dma_test_callback(void *dma_async_param)
+{
+ struct completion *cmp = dma_async_param;
+
+ complete(cmp);
+}
+
+/**
+ * ioat_dma_self_test - Perform a IOAT transaction to verify the HW works.
+ * @device: device to be tested
+ */
+int __devinit ioat_dma_self_test(struct ioatdma_device *device)
+{
+ int i;
+ u8 *src;
+ u8 *dest;
+ struct dma_device *dma = &device->common;
+ struct device *dev = &device->pdev->dev;
+ struct dma_chan *dma_chan;
+ struct dma_async_tx_descriptor *tx;
+ dma_addr_t dma_dest, dma_src;
+ dma_cookie_t cookie;
+ int err = 0;
+ struct completion cmp;
+ unsigned long tmo;
+ unsigned long flags;
+
+ src = kzalloc(sizeof(u8) * IOAT_TEST_SIZE, GFP_KERNEL);
+ if (!src)
+ return -ENOMEM;
+ dest = kzalloc(sizeof(u8) * IOAT_TEST_SIZE, GFP_KERNEL);
+ if (!dest) {
+ kfree(src);
+ return -ENOMEM;
+ }
+
+ /* Fill in src buffer */
+ for (i = 0; i < IOAT_TEST_SIZE; i++)
+ src[i] = (u8)i;
+
+ /* Start copy, using first DMA channel */
+ dma_chan = container_of(dma->channels.next, struct dma_chan,
+ device_node);
+ if (dma->device_alloc_chan_resources(dma_chan) < 1) {
+ dev_err(dev, "selftest cannot allocate chan resource\n");
+ err = -ENODEV;
+ goto out;
+ }
+
+ dma_src = dma_map_single(dev, src, IOAT_TEST_SIZE, DMA_TO_DEVICE);
+ dma_dest = dma_map_single(dev, dest, IOAT_TEST_SIZE, DMA_FROM_DEVICE);
+ flags = DMA_COMPL_SRC_UNMAP_SINGLE | DMA_COMPL_DEST_UNMAP_SINGLE |
+ DMA_PREP_INTERRUPT;
+ tx = device->common.device_prep_dma_memcpy(dma_chan, dma_dest, dma_src,
+ IOAT_TEST_SIZE, flags);
+ if (!tx) {
+ dev_err(dev, "Self-test prep failed, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ async_tx_ack(tx);
+ init_completion(&cmp);
+ tx->callback = ioat_dma_test_callback;
+ tx->callback_param = &cmp;
+ cookie = tx->tx_submit(tx);
+ if (cookie < 0) {
+ dev_err(dev, "Self-test setup failed, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ dma->device_issue_pending(dma_chan);
+
+ tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+
+ if (tmo == 0 ||
+ dma->device_is_tx_complete(dma_chan, cookie, NULL, NULL)
+ != DMA_SUCCESS) {
+ dev_err(dev, "Self-test copy timed out, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ if (memcmp(src, dest, IOAT_TEST_SIZE)) {
+ dev_err(dev, "Self-test copy failed compare, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+free_resources:
+ dma->device_free_chan_resources(dma_chan);
+out:
+ kfree(src);
+ kfree(dest);
+ return err;
+}
+
+static char ioat_interrupt_style[32] = "msix";
+module_param_string(ioat_interrupt_style, ioat_interrupt_style,
+ sizeof(ioat_interrupt_style), 0644);
+MODULE_PARM_DESC(ioat_interrupt_style,
+ "set ioat interrupt style: msix (default), "
+ "msix-single-vector, msi, intx)");
+
+/**
+ * ioat_dma_setup_interrupts - setup interrupt handler
+ * @device: ioat device
+ */
+static int ioat_dma_setup_interrupts(struct ioatdma_device *device)
+{
+ struct ioat_chan_common *chan;
+ struct pci_dev *pdev = device->pdev;
+ struct device *dev = &pdev->dev;
+ struct msix_entry *msix;
+ int i, j, msixcnt;
+ int err = -EINVAL;
+ u8 intrctrl = 0;
+
+ if (!strcmp(ioat_interrupt_style, "msix"))
+ goto msix;
+ if (!strcmp(ioat_interrupt_style, "msix-single-vector"))
+ goto msix_single_vector;
+ if (!strcmp(ioat_interrupt_style, "msi"))
+ goto msi;
+ if (!strcmp(ioat_interrupt_style, "intx"))
+ goto intx;
+ dev_err(dev, "invalid ioat_interrupt_style %s\n", ioat_interrupt_style);
+ goto err_no_irq;
+
+msix:
+ /* The number of MSI-X vectors should equal the number of channels */
+ msixcnt = device->common.chancnt;
+ for (i = 0; i < msixcnt; i++)
+ device->msix_entries[i].entry = i;
+
+ err = pci_enable_msix(pdev, device->msix_entries, msixcnt);
+ if (err < 0)
+ goto msi;
+ if (err > 0)
+ goto msix_single_vector;
+
+ for (i = 0; i < msixcnt; i++) {
+ msix = &device->msix_entries[i];
+ chan = ioat_chan_by_index(device, i);
+ err = devm_request_irq(dev, msix->vector,
+ ioat_dma_do_interrupt_msix, 0,
+ "ioat-msix", chan);
+ if (err) {
+ for (j = 0; j < i; j++) {
+ msix = &device->msix_entries[j];
+ chan = ioat_chan_by_index(device, j);
+ devm_free_irq(dev, msix->vector, chan);
+ }
+ goto msix_single_vector;
+ }
+ }
+ intrctrl |= IOAT_INTRCTRL_MSIX_VECTOR_CONTROL;
+ goto done;
+
+msix_single_vector:
+ msix = &device->msix_entries[0];
+ msix->entry = 0;
+ err = pci_enable_msix(pdev, device->msix_entries, 1);
+ if (err)
+ goto msi;
+
+ err = devm_request_irq(dev, msix->vector, ioat_dma_do_interrupt, 0,
+ "ioat-msix", device);
+ if (err) {
+ pci_disable_msix(pdev);
+ goto msi;
+ }
+ goto done;
+
+msi:
+ err = pci_enable_msi(pdev);
+ if (err)
+ goto intx;
+
+ err = devm_request_irq(dev, pdev->irq, ioat_dma_do_interrupt, 0,
+ "ioat-msi", device);
+ if (err) {
+ pci_disable_msi(pdev);
+ goto intx;
+ }
+ goto done;
+
+intx:
+ err = devm_request_irq(dev, pdev->irq, ioat_dma_do_interrupt,
+ IRQF_SHARED, "ioat-intx", device);
+ if (err)
+ goto err_no_irq;
+
+done:
+ if (device->intr_quirk)
+ device->intr_quirk(device);
+ intrctrl |= IOAT_INTRCTRL_MASTER_INT_EN;
+ writeb(intrctrl, device->reg_base + IOAT_INTRCTRL_OFFSET);
+ return 0;
+
+err_no_irq:
+ /* Disable all interrupt generation */
+ writeb(0, device->reg_base + IOAT_INTRCTRL_OFFSET);
+ dev_err(dev, "no usable interrupts\n");
+ return err;
+}
+
+static void ioat_disable_interrupts(struct ioatdma_device *device)
+{
+ /* Disable all interrupt generation */
+ writeb(0, device->reg_base + IOAT_INTRCTRL_OFFSET);
+}
+
+int __devinit ioat_probe(struct ioatdma_device *device)
+{
+ int err = -ENODEV;
+ struct dma_device *dma = &device->common;
+ struct pci_dev *pdev = device->pdev;
+ struct device *dev = &pdev->dev;
+
+ /* DMA coherent memory pool for DMA descriptor allocations */
+ device->dma_pool = pci_pool_create("dma_desc_pool", pdev,
+ sizeof(struct ioat_dma_descriptor),
+ 64, 0);
+ if (!device->dma_pool) {
+ err = -ENOMEM;
+ goto err_dma_pool;
+ }
+
+ device->completion_pool = pci_pool_create("completion_pool", pdev,
+ sizeof(u64), SMP_CACHE_BYTES,
+ SMP_CACHE_BYTES);
+
+ if (!device->completion_pool) {
+ err = -ENOMEM;
+ goto err_completion_pool;
+ }
+
+ device->enumerate_channels(device);
+
+ dma_cap_set(DMA_MEMCPY, dma->cap_mask);
+ dma->dev = &pdev->dev;
+
+ if (!dma->chancnt) {
+ dev_err(dev, "zero channels detected\n");
+ goto err_setup_interrupts;
+ }
+
+ err = ioat_dma_setup_interrupts(device);
+ if (err)
+ goto err_setup_interrupts;
+
+ err = device->self_test(device);
+ if (err)
+ goto err_self_test;
+
+ return 0;
+
+err_self_test:
+ ioat_disable_interrupts(device);
+err_setup_interrupts:
+ pci_pool_destroy(device->completion_pool);
+err_completion_pool:
+ pci_pool_destroy(device->dma_pool);
+err_dma_pool:
+ return err;
+}
+
+int __devinit ioat_register(struct ioatdma_device *device)
+{
+ int err = dma_async_device_register(&device->common);
+
+ if (err) {
+ ioat_disable_interrupts(device);
+ pci_pool_destroy(device->completion_pool);
+ pci_pool_destroy(device->dma_pool);
+ }
+
+ return err;
+}
+
+/* ioat1_intr_quirk - fix up dma ctrl register to enable / disable msi */
+static void ioat1_intr_quirk(struct ioatdma_device *device)
+{
+ struct pci_dev *pdev = device->pdev;
+ u32 dmactrl;
+
+ pci_read_config_dword(pdev, IOAT_PCI_DMACTRL_OFFSET, &dmactrl);
+ if (pdev->msi_enabled)
+ dmactrl |= IOAT_PCI_DMACTRL_MSI_EN;
+ else
+ dmactrl &= ~IOAT_PCI_DMACTRL_MSI_EN;
+ pci_write_config_dword(pdev, IOAT_PCI_DMACTRL_OFFSET, dmactrl);
+}
+
+static ssize_t ring_size_show(struct dma_chan *c, char *page)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+
+ return sprintf(page, "%d\n", ioat->desccount);
+}
+static struct ioat_sysfs_entry ring_size_attr = __ATTR_RO(ring_size);
+
+static ssize_t ring_active_show(struct dma_chan *c, char *page)
+{
+ struct ioat_dma_chan *ioat = to_ioat_chan(c);
+
+ return sprintf(page, "%d\n", ioat->active);
+}
+static struct ioat_sysfs_entry ring_active_attr = __ATTR_RO(ring_active);
+
+static ssize_t cap_show(struct dma_chan *c, char *page)
+{
+ struct dma_device *dma = c->device;
+
+ return sprintf(page, "copy%s%s%s%s%s%s\n",
+ dma_has_cap(DMA_PQ, dma->cap_mask) ? " pq" : "",
+ dma_has_cap(DMA_PQ_VAL, dma->cap_mask) ? " pq_val" : "",
+ dma_has_cap(DMA_XOR, dma->cap_mask) ? " xor" : "",
+ dma_has_cap(DMA_XOR_VAL, dma->cap_mask) ? " xor_val" : "",
+ dma_has_cap(DMA_MEMSET, dma->cap_mask) ? " fill" : "",
+ dma_has_cap(DMA_INTERRUPT, dma->cap_mask) ? " intr" : "");
+
+}
+struct ioat_sysfs_entry ioat_cap_attr = __ATTR_RO(cap);
+
+static ssize_t version_show(struct dma_chan *c, char *page)
+{
+ struct dma_device *dma = c->device;
+ struct ioatdma_device *device = to_ioatdma_device(dma);
+
+ return sprintf(page, "%d.%d\n",
+ device->version >> 4, device->version & 0xf);
+}
+struct ioat_sysfs_entry ioat_version_attr = __ATTR_RO(version);
+
+static struct attribute *ioat1_attrs[] = {
+ &ring_size_attr.attr,
+ &ring_active_attr.attr,
+ &ioat_cap_attr.attr,
+ &ioat_version_attr.attr,
+ NULL,
+};
+
+static ssize_t
+ioat_attr_show(struct kobject *kobj, struct attribute *attr, char *page)
+{
+ struct ioat_sysfs_entry *entry;
+ struct ioat_chan_common *chan;
+
+ entry = container_of(attr, struct ioat_sysfs_entry, attr);
+ chan = container_of(kobj, struct ioat_chan_common, kobj);
+
+ if (!entry->show)
+ return -EIO;
+ return entry->show(&chan->common, page);
+}
+
+struct sysfs_ops ioat_sysfs_ops = {
+ .show = ioat_attr_show,
+};
+
+static struct kobj_type ioat1_ktype = {
+ .sysfs_ops = &ioat_sysfs_ops,
+ .default_attrs = ioat1_attrs,
+};
+
+void ioat_kobject_add(struct ioatdma_device *device, struct kobj_type *type)
+{
+ struct dma_device *dma = &device->common;
+ struct dma_chan *c;
+
+ list_for_each_entry(c, &dma->channels, device_node) {
+ struct ioat_chan_common *chan = to_chan_common(c);
+ struct kobject *parent = &c->dev->device.kobj;
+ int err;
+
+ err = kobject_init_and_add(&chan->kobj, type, parent, "quickdata");
+ if (err) {
+ dev_warn(to_dev(chan),
+ "sysfs init error (%d), continuing...\n", err);
+ kobject_put(&chan->kobj);
+ set_bit(IOAT_KOBJ_INIT_FAIL, &chan->state);
+ }
+ }
+}
+
+void ioat_kobject_del(struct ioatdma_device *device)
+{
+ struct dma_device *dma = &device->common;
+ struct dma_chan *c;
+
+ list_for_each_entry(c, &dma->channels, device_node) {
+ struct ioat_chan_common *chan = to_chan_common(c);
+
+ if (!test_bit(IOAT_KOBJ_INIT_FAIL, &chan->state)) {
+ kobject_del(&chan->kobj);
+ kobject_put(&chan->kobj);
+ }
+ }
+}
+
+int __devinit ioat1_dma_probe(struct ioatdma_device *device, int dca)
+{
+ struct pci_dev *pdev = device->pdev;
+ struct dma_device *dma;
+ int err;
+
+ device->intr_quirk = ioat1_intr_quirk;
+ device->enumerate_channels = ioat1_enumerate_channels;
+ device->self_test = ioat_dma_self_test;
+ dma = &device->common;
+ dma->device_prep_dma_memcpy = ioat1_dma_prep_memcpy;
+ dma->device_issue_pending = ioat1_dma_memcpy_issue_pending;
+ dma->device_alloc_chan_resources = ioat1_dma_alloc_chan_resources;
+ dma->device_free_chan_resources = ioat1_dma_free_chan_resources;
+ dma->device_is_tx_complete = ioat1_dma_is_complete;
+
+ err = ioat_probe(device);
+ if (err)
+ return err;
+ ioat_set_tcp_copy_break(4096);
+ err = ioat_register(device);
+ if (err)
+ return err;
+ ioat_kobject_add(device, &ioat1_ktype);
+
+ if (dca)
+ device->dca = ioat_dca_init(pdev, device->reg_base);
+
+ return err;
+}
+
+void __devexit ioat_dma_remove(struct ioatdma_device *device)
+{
+ struct dma_device *dma = &device->common;
+
+ ioat_disable_interrupts(device);
+
+ ioat_kobject_del(device);
+
+ dma_async_device_unregister(dma);
+
+ pci_pool_destroy(device->dma_pool);
+ pci_pool_destroy(device->completion_pool);
+
+ INIT_LIST_HEAD(&dma->channels);
+}
--- /dev/null
+/*
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called COPYING.
+ */
+#ifndef IOATDMA_H
+#define IOATDMA_H
+
+#include <linux/dmaengine.h>
+#include "hw.h"
+#include "registers.h"
+#include <linux/init.h>
+#include <linux/dmapool.h>
+#include <linux/cache.h>
+#include <linux/pci_ids.h>
+#include <net/tcp.h>
+
+#define IOAT_DMA_VERSION "4.00"
+
+#define IOAT_LOW_COMPLETION_MASK 0xffffffc0
+#define IOAT_DMA_DCA_ANY_CPU ~0
+
+#define to_ioatdma_device(dev) container_of(dev, struct ioatdma_device, common)
+#define to_ioat_desc(lh) container_of(lh, struct ioat_desc_sw, node)
+#define tx_to_ioat_desc(tx) container_of(tx, struct ioat_desc_sw, txd)
+#define to_dev(ioat_chan) (&(ioat_chan)->device->pdev->dev)
+
+#define chan_num(ch) ((int)((ch)->reg_base - (ch)->device->reg_base) / 0x80)
+
+/*
+ * workaround for IOAT ver.3.0 null descriptor issue
+ * (channel returns error when size is 0)
+ */
+#define NULL_DESC_BUFFER_SIZE 1
+
+/**
+ * struct ioatdma_device - internal representation of a IOAT device
+ * @pdev: PCI-Express device
+ * @reg_base: MMIO register space base address
+ * @dma_pool: for allocating DMA descriptors
+ * @common: embedded struct dma_device
+ * @version: version of ioatdma device
+ * @msix_entries: irq handlers
+ * @idx: per channel data
+ * @dca: direct cache access context
+ * @intr_quirk: interrupt setup quirk (for ioat_v1 devices)
+ * @enumerate_channels: hw version specific channel enumeration
+ * @cleanup_tasklet: select between the v2 and v3 cleanup routines
+ * @timer_fn: select between the v2 and v3 timer watchdog routines
+ * @self_test: hardware version specific self test for each supported op type
+ *
+ * Note: the v3 cleanup routine supports raid operations
+ */
+struct ioatdma_device {
+ struct pci_dev *pdev;
+ void __iomem *reg_base;
+ struct pci_pool *dma_pool;
+ struct pci_pool *completion_pool;
+ struct dma_device common;
+ u8 version;
+ struct msix_entry msix_entries[4];
+ struct ioat_chan_common *idx[4];
+ struct dca_provider *dca;
+ void (*intr_quirk)(struct ioatdma_device *device);
+ int (*enumerate_channels)(struct ioatdma_device *device);
+ void (*cleanup_tasklet)(unsigned long data);
+ void (*timer_fn)(unsigned long data);
+ int (*self_test)(struct ioatdma_device *device);
+};
+
+struct ioat_chan_common {
+ struct dma_chan common;
+ void __iomem *reg_base;
+ unsigned long last_completion;
+ spinlock_t cleanup_lock;
+ dma_cookie_t completed_cookie;
+ unsigned long state;
+ #define IOAT_COMPLETION_PENDING 0
+ #define IOAT_COMPLETION_ACK 1
+ #define IOAT_RESET_PENDING 2
+ #define IOAT_KOBJ_INIT_FAIL 3
+ struct timer_list timer;
+ #define COMPLETION_TIMEOUT msecs_to_jiffies(100)
+ #define IDLE_TIMEOUT msecs_to_jiffies(2000)
+ #define RESET_DELAY msecs_to_jiffies(100)
+ struct ioatdma_device *device;
+ dma_addr_t completion_dma;
+ u64 *completion;
+ struct tasklet_struct cleanup_task;
+ struct kobject kobj;
+};
+
+struct ioat_sysfs_entry {
+ struct attribute attr;
+ ssize_t (*show)(struct dma_chan *, char *);
+};
+
+/**
+ * struct ioat_dma_chan - internal representation of a DMA channel
+ */
+struct ioat_dma_chan {
+ struct ioat_chan_common base;
+
+ size_t xfercap; /* XFERCAP register value expanded out */
+
+ spinlock_t desc_lock;
+ struct list_head free_desc;
+ struct list_head used_desc;
+
+ int pending;
+ u16 desccount;
+ u16 active;
+};
+
+static inline struct ioat_chan_common *to_chan_common(struct dma_chan *c)
+{
+ return container_of(c, struct ioat_chan_common, common);
+}
+
+static inline struct ioat_dma_chan *to_ioat_chan(struct dma_chan *c)
+{
+ struct ioat_chan_common *chan = to_chan_common(c);
+
+ return container_of(chan, struct ioat_dma_chan, base);
+}
+
+/**
+ * ioat_is_complete - poll the status of an ioat transaction
+ * @c: channel handle
+ * @cookie: transaction identifier
+ * @done: if set, updated with last completed transaction
+ * @used: if set, updated with last used transaction
+ */
+static inline enum dma_status
+ioat_is_complete(struct dma_chan *c, dma_cookie_t cookie,
+ dma_cookie_t *done, dma_cookie_t *used)
+{
+ struct ioat_chan_common *chan = to_chan_common(c);
+ dma_cookie_t last_used;
+ dma_cookie_t last_complete;
+
+ last_used = c->cookie;
+ last_complete = chan->completed_cookie;
+
+ if (done)
+ *done = last_complete;
+ if (used)
+ *used = last_used;
+
+ return dma_async_is_complete(cookie, last_complete, last_used);
+}
+
+/* wrapper around hardware descriptor format + additional software fields */
+
+/**
+ * struct ioat_desc_sw - wrapper around hardware descriptor
+ * @hw: hardware DMA descriptor (for memcpy)
+ * @node: this descriptor will either be on the free list,
+ * or attached to a transaction list (tx_list)
+ * @txd: the generic software descriptor for all engines
+ * @id: identifier for debug
+ */
+struct ioat_desc_sw {
+ struct ioat_dma_descriptor *hw;
+ struct list_head node;
+ size_t len;
+ struct list_head tx_list;
+ struct dma_async_tx_descriptor txd;
+ #ifdef DEBUG
+ int id;
+ #endif
+};
+
+#ifdef DEBUG
+#define set_desc_id(desc, i) ((desc)->id = (i))
+#define desc_id(desc) ((desc)->id)
+#else
+#define set_desc_id(desc, i)
+#define desc_id(desc) (0)
+#endif
+
+static inline void
+__dump_desc_dbg(struct ioat_chan_common *chan, struct ioat_dma_descriptor *hw,
+ struct dma_async_tx_descriptor *tx, int id)
+{
+ struct device *dev = to_dev(chan);
+
+ dev_dbg(dev, "desc[%d]: (%#llx->%#llx) cookie: %d flags: %#x"
+ " ctl: %#x (op: %d int_en: %d compl: %d)\n", id,
+ (unsigned long long) tx->phys,
+ (unsigned long long) hw->next, tx->cookie, tx->flags,
+ hw->ctl, hw->ctl_f.op, hw->ctl_f.int_en, hw->ctl_f.compl_write);
+}
+
+#define dump_desc_dbg(c, d) \
+ ({ if (d) __dump_desc_dbg(&c->base, d->hw, &d->txd, desc_id(d)); 0; })
+
+static inline void ioat_set_tcp_copy_break(unsigned long copybreak)
+{
+ #ifdef CONFIG_NET_DMA
+ sysctl_tcp_dma_copybreak = copybreak;
+ #endif
+}
+
+static inline struct ioat_chan_common *
+ioat_chan_by_index(struct ioatdma_device *device, int index)
+{
+ return device->idx[index];
+}
+
+static inline u64 ioat_chansts(struct ioat_chan_common *chan)
+{
+ u8 ver = chan->device->version;
+ u64 status;
+ u32 status_lo;
+
+ /* We need to read the low address first as this causes the
+ * chipset to latch the upper bits for the subsequent read
+ */
+ status_lo = readl(chan->reg_base + IOAT_CHANSTS_OFFSET_LOW(ver));
+ status = readl(chan->reg_base + IOAT_CHANSTS_OFFSET_HIGH(ver));
+ status <<= 32;
+ status |= status_lo;
+
+ return status;
+}
+
+static inline void ioat_start(struct ioat_chan_common *chan)
+{
+ u8 ver = chan->device->version;
+
+ writeb(IOAT_CHANCMD_START, chan->reg_base + IOAT_CHANCMD_OFFSET(ver));
+}
+
+static inline u64 ioat_chansts_to_addr(u64 status)
+{
+ return status & IOAT_CHANSTS_COMPLETED_DESCRIPTOR_ADDR;
+}
+
+static inline u32 ioat_chanerr(struct ioat_chan_common *chan)
+{
+ return readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+}
+
+static inline void ioat_suspend(struct ioat_chan_common *chan)
+{
+ u8 ver = chan->device->version;
+
+ writeb(IOAT_CHANCMD_SUSPEND, chan->reg_base + IOAT_CHANCMD_OFFSET(ver));
+}
+
+static inline void ioat_set_chainaddr(struct ioat_dma_chan *ioat, u64 addr)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+
+ writel(addr & 0x00000000FFFFFFFF,
+ chan->reg_base + IOAT1_CHAINADDR_OFFSET_LOW);
+ writel(addr >> 32,
+ chan->reg_base + IOAT1_CHAINADDR_OFFSET_HIGH);
+}
+
+static inline bool is_ioat_active(unsigned long status)
+{
+ return ((status & IOAT_CHANSTS_STATUS) == IOAT_CHANSTS_ACTIVE);
+}
+
+static inline bool is_ioat_idle(unsigned long status)
+{
+ return ((status & IOAT_CHANSTS_STATUS) == IOAT_CHANSTS_DONE);
+}
+
+static inline bool is_ioat_halted(unsigned long status)
+{
+ return ((status & IOAT_CHANSTS_STATUS) == IOAT_CHANSTS_HALTED);
+}
+
+static inline bool is_ioat_suspended(unsigned long status)
+{
+ return ((status & IOAT_CHANSTS_STATUS) == IOAT_CHANSTS_SUSPENDED);
+}
+
+/* channel was fatally programmed */
+static inline bool is_ioat_bug(unsigned long err)
+{
+ return !!(err & (IOAT_CHANERR_SRC_ADDR_ERR|IOAT_CHANERR_DEST_ADDR_ERR|
+ IOAT_CHANERR_NEXT_ADDR_ERR|IOAT_CHANERR_CONTROL_ERR|
+ IOAT_CHANERR_LENGTH_ERR));
+}
+
+static inline void ioat_unmap(struct pci_dev *pdev, dma_addr_t addr, size_t len,
+ int direction, enum dma_ctrl_flags flags, bool dst)
+{
+ if ((dst && (flags & DMA_COMPL_DEST_UNMAP_SINGLE)) ||
+ (!dst && (flags & DMA_COMPL_SRC_UNMAP_SINGLE)))
+ pci_unmap_single(pdev, addr, len, direction);
+ else
+ pci_unmap_page(pdev, addr, len, direction);
+}
+
+int __devinit ioat_probe(struct ioatdma_device *device);
+int __devinit ioat_register(struct ioatdma_device *device);
+int __devinit ioat1_dma_probe(struct ioatdma_device *dev, int dca);
+int __devinit ioat_dma_self_test(struct ioatdma_device *device);
+void __devexit ioat_dma_remove(struct ioatdma_device *device);
+struct dca_provider * __devinit ioat_dca_init(struct pci_dev *pdev,
+ void __iomem *iobase);
+unsigned long ioat_get_current_completion(struct ioat_chan_common *chan);
+void ioat_init_channel(struct ioatdma_device *device,
+ struct ioat_chan_common *chan, int idx,
+ void (*timer_fn)(unsigned long),
+ void (*tasklet)(unsigned long),
+ unsigned long ioat);
+void ioat_dma_unmap(struct ioat_chan_common *chan, enum dma_ctrl_flags flags,
+ size_t len, struct ioat_dma_descriptor *hw);
+bool ioat_cleanup_preamble(struct ioat_chan_common *chan,
+ unsigned long *phys_complete);
+void ioat_kobject_add(struct ioatdma_device *device, struct kobj_type *type);
+void ioat_kobject_del(struct ioatdma_device *device);
+extern struct sysfs_ops ioat_sysfs_ops;
+extern struct ioat_sysfs_entry ioat_version_attr;
+extern struct ioat_sysfs_entry ioat_cap_attr;
+#endif /* IOATDMA_H */
--- /dev/null
+/*
+ * Intel I/OAT DMA Linux driver
+ * Copyright(c) 2004 - 2009 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ *
+ */
+
+/*
+ * This driver supports an Intel I/OAT DMA engine (versions >= 2), which
+ * does asynchronous data movement and checksumming operations.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/dmaengine.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/workqueue.h>
+#include <linux/i7300_idle.h>
+#include "dma.h"
+#include "dma_v2.h"
+#include "registers.h"
+#include "hw.h"
+
+int ioat_ring_alloc_order = 8;
+module_param(ioat_ring_alloc_order, int, 0644);
+MODULE_PARM_DESC(ioat_ring_alloc_order,
+ "ioat2+: allocate 2^n descriptors per channel"
+ " (default: 8 max: 16)");
+static int ioat_ring_max_alloc_order = IOAT_MAX_ORDER;
+module_param(ioat_ring_max_alloc_order, int, 0644);
+MODULE_PARM_DESC(ioat_ring_max_alloc_order,
+ "ioat2+: upper limit for ring size (default: 16)");
+
+void __ioat2_issue_pending(struct ioat2_dma_chan *ioat)
+{
+ void * __iomem reg_base = ioat->base.reg_base;
+
+ ioat->pending = 0;
+ ioat->dmacount += ioat2_ring_pending(ioat);
+ ioat->issued = ioat->head;
+ /* make descriptor updates globally visible before notifying channel */
+ wmb();
+ writew(ioat->dmacount, reg_base + IOAT_CHAN_DMACOUNT_OFFSET);
+ dev_dbg(to_dev(&ioat->base),
+ "%s: head: %#x tail: %#x issued: %#x count: %#x\n",
+ __func__, ioat->head, ioat->tail, ioat->issued, ioat->dmacount);
+}
+
+void ioat2_issue_pending(struct dma_chan *chan)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(chan);
+
+ spin_lock_bh(&ioat->ring_lock);
+ if (ioat->pending == 1)
+ __ioat2_issue_pending(ioat);
+ spin_unlock_bh(&ioat->ring_lock);
+}
+
+/**
+ * ioat2_update_pending - log pending descriptors
+ * @ioat: ioat2+ channel
+ *
+ * set pending to '1' unless pending is already set to '2', pending == 2
+ * indicates that submission is temporarily blocked due to an in-flight
+ * reset. If we are already above the ioat_pending_level threshold then
+ * just issue pending.
+ *
+ * called with ring_lock held
+ */
+static void ioat2_update_pending(struct ioat2_dma_chan *ioat)
+{
+ if (unlikely(ioat->pending == 2))
+ return;
+ else if (ioat2_ring_pending(ioat) > ioat_pending_level)
+ __ioat2_issue_pending(ioat);
+ else
+ ioat->pending = 1;
+}
+
+static void __ioat2_start_null_desc(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_ring_ent *desc;
+ struct ioat_dma_descriptor *hw;
+ int idx;
+
+ if (ioat2_ring_space(ioat) < 1) {
+ dev_err(to_dev(&ioat->base),
+ "Unable to start null desc - ring full\n");
+ return;
+ }
+
+ dev_dbg(to_dev(&ioat->base), "%s: head: %#x tail: %#x issued: %#x\n",
+ __func__, ioat->head, ioat->tail, ioat->issued);
+ idx = ioat2_desc_alloc(ioat, 1);
+ desc = ioat2_get_ring_ent(ioat, idx);
+
+ hw = desc->hw;
+ hw->ctl = 0;
+ hw->ctl_f.null = 1;
+ hw->ctl_f.int_en = 1;
+ hw->ctl_f.compl_write = 1;
+ /* set size to non-zero value (channel returns error when size is 0) */
+ hw->size = NULL_DESC_BUFFER_SIZE;
+ hw->src_addr = 0;
+ hw->dst_addr = 0;
+ async_tx_ack(&desc->txd);
+ ioat2_set_chainaddr(ioat, desc->txd.phys);
+ dump_desc_dbg(ioat, desc);
+ __ioat2_issue_pending(ioat);
+}
+
+static void ioat2_start_null_desc(struct ioat2_dma_chan *ioat)
+{
+ spin_lock_bh(&ioat->ring_lock);
+ __ioat2_start_null_desc(ioat);
+ spin_unlock_bh(&ioat->ring_lock);
+}
+
+static void __cleanup(struct ioat2_dma_chan *ioat, unsigned long phys_complete)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ struct dma_async_tx_descriptor *tx;
+ struct ioat_ring_ent *desc;
+ bool seen_current = false;
+ u16 active;
+ int i;
+
+ dev_dbg(to_dev(chan), "%s: head: %#x tail: %#x issued: %#x\n",
+ __func__, ioat->head, ioat->tail, ioat->issued);
+
+ active = ioat2_ring_active(ioat);
+ for (i = 0; i < active && !seen_current; i++) {
+ prefetch(ioat2_get_ring_ent(ioat, ioat->tail + i + 1));
+ desc = ioat2_get_ring_ent(ioat, ioat->tail + i);
+ tx = &desc->txd;
+ dump_desc_dbg(ioat, desc);
+ if (tx->cookie) {
+ ioat_dma_unmap(chan, tx->flags, desc->len, desc->hw);
+ chan->completed_cookie = tx->cookie;
+ tx->cookie = 0;
+ if (tx->callback) {
+ tx->callback(tx->callback_param);
+ tx->callback = NULL;
+ }
+ }
+
+ if (tx->phys == phys_complete)
+ seen_current = true;
+ }
+ ioat->tail += i;
+ BUG_ON(!seen_current); /* no active descs have written a completion? */
+
+ chan->last_completion = phys_complete;
+ if (ioat->head == ioat->tail) {
+ dev_dbg(to_dev(chan), "%s: cancel completion timeout\n",
+ __func__);
+ clear_bit(IOAT_COMPLETION_PENDING, &chan->state);
+ mod_timer(&chan->timer, jiffies + IDLE_TIMEOUT);
+ }
+}
+
+/**
+ * ioat2_cleanup - clean finished descriptors (advance tail pointer)
+ * @chan: ioat channel to be cleaned up
+ */
+static void ioat2_cleanup(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ unsigned long phys_complete;
+
+ prefetch(chan->completion);
+
+ if (!spin_trylock_bh(&chan->cleanup_lock))
+ return;
+
+ if (!ioat_cleanup_preamble(chan, &phys_complete)) {
+ spin_unlock_bh(&chan->cleanup_lock);
+ return;
+ }
+
+ if (!spin_trylock_bh(&ioat->ring_lock)) {
+ spin_unlock_bh(&chan->cleanup_lock);
+ return;
+ }
+
+ __cleanup(ioat, phys_complete);
+
+ spin_unlock_bh(&ioat->ring_lock);
+ spin_unlock_bh(&chan->cleanup_lock);
+}
+
+void ioat2_cleanup_tasklet(unsigned long data)
+{
+ struct ioat2_dma_chan *ioat = (void *) data;
+
+ ioat2_cleanup(ioat);
+ writew(IOAT_CHANCTRL_RUN, ioat->base.reg_base + IOAT_CHANCTRL_OFFSET);
+}
+
+void __ioat2_restart_chan(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+
+ /* set the tail to be re-issued */
+ ioat->issued = ioat->tail;
+ ioat->dmacount = 0;
+ set_bit(IOAT_COMPLETION_PENDING, &chan->state);
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+
+ dev_dbg(to_dev(chan),
+ "%s: head: %#x tail: %#x issued: %#x count: %#x\n",
+ __func__, ioat->head, ioat->tail, ioat->issued, ioat->dmacount);
+
+ if (ioat2_ring_pending(ioat)) {
+ struct ioat_ring_ent *desc;
+
+ desc = ioat2_get_ring_ent(ioat, ioat->tail);
+ ioat2_set_chainaddr(ioat, desc->txd.phys);
+ __ioat2_issue_pending(ioat);
+ } else
+ __ioat2_start_null_desc(ioat);
+}
+
+static void ioat2_restart_channel(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ unsigned long phys_complete;
+ u32 status;
+
+ status = ioat_chansts(chan);
+ if (is_ioat_active(status) || is_ioat_idle(status))
+ ioat_suspend(chan);
+ while (is_ioat_active(status) || is_ioat_idle(status)) {
+ status = ioat_chansts(chan);
+ cpu_relax();
+ }
+
+ if (ioat_cleanup_preamble(chan, &phys_complete))
+ __cleanup(ioat, phys_complete);
+
+ __ioat2_restart_chan(ioat);
+}
+
+void ioat2_timer_event(unsigned long data)
+{
+ struct ioat2_dma_chan *ioat = (void *) data;
+ struct ioat_chan_common *chan = &ioat->base;
+
+ spin_lock_bh(&chan->cleanup_lock);
+ if (test_bit(IOAT_COMPLETION_PENDING, &chan->state)) {
+ unsigned long phys_complete;
+ u64 status;
+
+ spin_lock_bh(&ioat->ring_lock);
+ status = ioat_chansts(chan);
+
+ /* when halted due to errors check for channel
+ * programming errors before advancing the completion state
+ */
+ if (is_ioat_halted(status)) {
+ u32 chanerr;
+
+ chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ BUG_ON(is_ioat_bug(chanerr));
+ }
+
+ /* if we haven't made progress and we have already
+ * acknowledged a pending completion once, then be more
+ * forceful with a restart
+ */
+ if (ioat_cleanup_preamble(chan, &phys_complete))
+ __cleanup(ioat, phys_complete);
+ else if (test_bit(IOAT_COMPLETION_ACK, &chan->state))
+ ioat2_restart_channel(ioat);
+ else {
+ set_bit(IOAT_COMPLETION_ACK, &chan->state);
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+ }
+ spin_unlock_bh(&ioat->ring_lock);
+ } else {
+ u16 active;
+
+ /* if the ring is idle, empty, and oversized try to step
+ * down the size
+ */
+ spin_lock_bh(&ioat->ring_lock);
+ active = ioat2_ring_active(ioat);
+ if (active == 0 && ioat->alloc_order > ioat_get_alloc_order())
+ reshape_ring(ioat, ioat->alloc_order-1);
+ spin_unlock_bh(&ioat->ring_lock);
+
+ /* keep shrinking until we get back to our minimum
+ * default size
+ */
+ if (ioat->alloc_order > ioat_get_alloc_order())
+ mod_timer(&chan->timer, jiffies + IDLE_TIMEOUT);
+ }
+ spin_unlock_bh(&chan->cleanup_lock);
+}
+
+/**
+ * ioat2_enumerate_channels - find and initialize the device's channels
+ * @device: the device to be enumerated
+ */
+int ioat2_enumerate_channels(struct ioatdma_device *device)
+{
+ struct ioat2_dma_chan *ioat;
+ struct device *dev = &device->pdev->dev;
+ struct dma_device *dma = &device->common;
+ u8 xfercap_log;
+ int i;
+
+ INIT_LIST_HEAD(&dma->channels);
+ dma->chancnt = readb(device->reg_base + IOAT_CHANCNT_OFFSET);
+ dma->chancnt &= 0x1f; /* bits [4:0] valid */
+ if (dma->chancnt > ARRAY_SIZE(device->idx)) {
+ dev_warn(dev, "(%d) exceeds max supported channels (%zu)\n",
+ dma->chancnt, ARRAY_SIZE(device->idx));
+ dma->chancnt = ARRAY_SIZE(device->idx);
+ }
+ xfercap_log = readb(device->reg_base + IOAT_XFERCAP_OFFSET);
+ xfercap_log &= 0x1f; /* bits [4:0] valid */
+ if (xfercap_log == 0)
+ return 0;
+ dev_dbg(dev, "%s: xfercap = %d\n", __func__, 1 << xfercap_log);
+
+ /* FIXME which i/oat version is i7300? */
+#ifdef CONFIG_I7300_IDLE_IOAT_CHANNEL
+ if (i7300_idle_platform_probe(NULL, NULL, 1) == 0)
+ dma->chancnt--;
+#endif
+ for (i = 0; i < dma->chancnt; i++) {
+ ioat = devm_kzalloc(dev, sizeof(*ioat), GFP_KERNEL);
+ if (!ioat)
+ break;
+
+ ioat_init_channel(device, &ioat->base, i,
+ device->timer_fn,
+ device->cleanup_tasklet,
+ (unsigned long) ioat);
+ ioat->xfercap_log = xfercap_log;
+ spin_lock_init(&ioat->ring_lock);
+ }
+ dma->chancnt = i;
+ return i;
+}
+
+static dma_cookie_t ioat2_tx_submit_unlock(struct dma_async_tx_descriptor *tx)
+{
+ struct dma_chan *c = tx->chan;
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_chan_common *chan = &ioat->base;
+ dma_cookie_t cookie = c->cookie;
+
+ cookie++;
+ if (cookie < 0)
+ cookie = 1;
+ tx->cookie = cookie;
+ c->cookie = cookie;
+ dev_dbg(to_dev(&ioat->base), "%s: cookie: %d\n", __func__, cookie);
+
+ if (!test_and_set_bit(IOAT_COMPLETION_PENDING, &chan->state))
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+ ioat2_update_pending(ioat);
+ spin_unlock_bh(&ioat->ring_lock);
+
+ return cookie;
+}
+
+static struct ioat_ring_ent *ioat2_alloc_ring_ent(struct dma_chan *chan, gfp_t flags)
+{
+ struct ioat_dma_descriptor *hw;
+ struct ioat_ring_ent *desc;
+ struct ioatdma_device *dma;
+ dma_addr_t phys;
+
+ dma = to_ioatdma_device(chan->device);
+ hw = pci_pool_alloc(dma->dma_pool, flags, &phys);
+ if (!hw)
+ return NULL;
+ memset(hw, 0, sizeof(*hw));
+
+ desc = kmem_cache_alloc(ioat2_cache, flags);
+ if (!desc) {
+ pci_pool_free(dma->dma_pool, hw, phys);
+ return NULL;
+ }
+ memset(desc, 0, sizeof(*desc));
+
+ dma_async_tx_descriptor_init(&desc->txd, chan);
+ desc->txd.tx_submit = ioat2_tx_submit_unlock;
+ desc->hw = hw;
+ desc->txd.phys = phys;
+ return desc;
+}
+
+static void ioat2_free_ring_ent(struct ioat_ring_ent *desc, struct dma_chan *chan)
+{
+ struct ioatdma_device *dma;
+
+ dma = to_ioatdma_device(chan->device);
+ pci_pool_free(dma->dma_pool, desc->hw, desc->txd.phys);
+ kmem_cache_free(ioat2_cache, desc);
+}
+
+static struct ioat_ring_ent **ioat2_alloc_ring(struct dma_chan *c, int order, gfp_t flags)
+{
+ struct ioat_ring_ent **ring;
+ int descs = 1 << order;
+ int i;
+
+ if (order > ioat_get_max_alloc_order())
+ return NULL;
+
+ /* allocate the array to hold the software ring */
+ ring = kcalloc(descs, sizeof(*ring), flags);
+ if (!ring)
+ return NULL;
+ for (i = 0; i < descs; i++) {
+ ring[i] = ioat2_alloc_ring_ent(c, flags);
+ if (!ring[i]) {
+ while (i--)
+ ioat2_free_ring_ent(ring[i], c);
+ kfree(ring);
+ return NULL;
+ }
+ set_desc_id(ring[i], i);
+ }
+
+ /* link descs */
+ for (i = 0; i < descs-1; i++) {
+ struct ioat_ring_ent *next = ring[i+1];
+ struct ioat_dma_descriptor *hw = ring[i]->hw;
+
+ hw->next = next->txd.phys;
+ }
+ ring[i]->hw->next = ring[0]->txd.phys;
+
+ return ring;
+}
+
+/* ioat2_alloc_chan_resources - allocate/initialize ioat2 descriptor ring
+ * @chan: channel to be initialized
+ */
+int ioat2_alloc_chan_resources(struct dma_chan *c)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioat_ring_ent **ring;
+ u32 chanerr;
+ int order;
+
+ /* have we already been set up? */
+ if (ioat->ring)
+ return 1 << ioat->alloc_order;
+
+ /* Setup register to interrupt and write completion status on error */
+ writew(IOAT_CHANCTRL_RUN, chan->reg_base + IOAT_CHANCTRL_OFFSET);
+
+ chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ if (chanerr) {
+ dev_err(to_dev(chan), "CHANERR = %x, clearing\n", chanerr);
+ writel(chanerr, chan->reg_base + IOAT_CHANERR_OFFSET);
+ }
+
+ /* allocate a completion writeback area */
+ /* doing 2 32bit writes to mmio since 1 64b write doesn't work */
+ chan->completion = pci_pool_alloc(chan->device->completion_pool,
+ GFP_KERNEL, &chan->completion_dma);
+ if (!chan->completion)
+ return -ENOMEM;
+
+ memset(chan->completion, 0, sizeof(*chan->completion));
+ writel(((u64) chan->completion_dma) & 0x00000000FFFFFFFF,
+ chan->reg_base + IOAT_CHANCMP_OFFSET_LOW);
+ writel(((u64) chan->completion_dma) >> 32,
+ chan->reg_base + IOAT_CHANCMP_OFFSET_HIGH);
+
+ order = ioat_get_alloc_order();
+ ring = ioat2_alloc_ring(c, order, GFP_KERNEL);
+ if (!ring)
+ return -ENOMEM;
+
+ spin_lock_bh(&ioat->ring_lock);
+ ioat->ring = ring;
+ ioat->head = 0;
+ ioat->issued = 0;
+ ioat->tail = 0;
+ ioat->pending = 0;
+ ioat->alloc_order = order;
+ spin_unlock_bh(&ioat->ring_lock);
+
+ tasklet_enable(&chan->cleanup_task);
+ ioat2_start_null_desc(ioat);
+
+ return 1 << ioat->alloc_order;
+}
+
+bool reshape_ring(struct ioat2_dma_chan *ioat, int order)
+{
+ /* reshape differs from normal ring allocation in that we want
+ * to allocate a new software ring while only
+ * extending/truncating the hardware ring
+ */
+ struct ioat_chan_common *chan = &ioat->base;
+ struct dma_chan *c = &chan->common;
+ const u16 curr_size = ioat2_ring_mask(ioat) + 1;
+ const u16 active = ioat2_ring_active(ioat);
+ const u16 new_size = 1 << order;
+ struct ioat_ring_ent **ring;
+ u16 i;
+
+ if (order > ioat_get_max_alloc_order())
+ return false;
+
+ /* double check that we have at least 1 free descriptor */
+ if (active == curr_size)
+ return false;
+
+ /* when shrinking, verify that we can hold the current active
+ * set in the new ring
+ */
+ if (active >= new_size)
+ return false;
+
+ /* allocate the array to hold the software ring */
+ ring = kcalloc(new_size, sizeof(*ring), GFP_NOWAIT);
+ if (!ring)
+ return false;
+
+ /* allocate/trim descriptors as needed */
+ if (new_size > curr_size) {
+ /* copy current descriptors to the new ring */
+ for (i = 0; i < curr_size; i++) {
+ u16 curr_idx = (ioat->tail+i) & (curr_size-1);
+ u16 new_idx = (ioat->tail+i) & (new_size-1);
+
+ ring[new_idx] = ioat->ring[curr_idx];
+ set_desc_id(ring[new_idx], new_idx);
+ }
+
+ /* add new descriptors to the ring */
+ for (i = curr_size; i < new_size; i++) {
+ u16 new_idx = (ioat->tail+i) & (new_size-1);
+
+ ring[new_idx] = ioat2_alloc_ring_ent(c, GFP_NOWAIT);
+ if (!ring[new_idx]) {
+ while (i--) {
+ u16 new_idx = (ioat->tail+i) & (new_size-1);
+
+ ioat2_free_ring_ent(ring[new_idx], c);
+ }
+ kfree(ring);
+ return false;
+ }
+ set_desc_id(ring[new_idx], new_idx);
+ }
+
+ /* hw link new descriptors */
+ for (i = curr_size-1; i < new_size; i++) {
+ u16 new_idx = (ioat->tail+i) & (new_size-1);
+ struct ioat_ring_ent *next = ring[(new_idx+1) & (new_size-1)];
+ struct ioat_dma_descriptor *hw = ring[new_idx]->hw;
+
+ hw->next = next->txd.phys;
+ }
+ } else {
+ struct ioat_dma_descriptor *hw;
+ struct ioat_ring_ent *next;
+
+ /* copy current descriptors to the new ring, dropping the
+ * removed descriptors
+ */
+ for (i = 0; i < new_size; i++) {
+ u16 curr_idx = (ioat->tail+i) & (curr_size-1);
+ u16 new_idx = (ioat->tail+i) & (new_size-1);
+
+ ring[new_idx] = ioat->ring[curr_idx];
+ set_desc_id(ring[new_idx], new_idx);
+ }
+
+ /* free deleted descriptors */
+ for (i = new_size; i < curr_size; i++) {
+ struct ioat_ring_ent *ent;
+
+ ent = ioat2_get_ring_ent(ioat, ioat->tail+i);
+ ioat2_free_ring_ent(ent, c);
+ }
+
+ /* fix up hardware ring */
+ hw = ring[(ioat->tail+new_size-1) & (new_size-1)]->hw;
+ next = ring[(ioat->tail+new_size) & (new_size-1)];
+ hw->next = next->txd.phys;
+ }
+
+ dev_dbg(to_dev(chan), "%s: allocated %d descriptors\n",
+ __func__, new_size);
+
+ kfree(ioat->ring);
+ ioat->ring = ring;
+ ioat->alloc_order = order;
+
+ return true;
+}
+
+/**
+ * ioat2_alloc_and_lock - common descriptor alloc boilerplate for ioat2,3 ops
+ * @idx: gets starting descriptor index on successful allocation
+ * @ioat: ioat2,3 channel (ring) to operate on
+ * @num_descs: allocation length
+ */
+int ioat2_alloc_and_lock(u16 *idx, struct ioat2_dma_chan *ioat, int num_descs)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+
+ spin_lock_bh(&ioat->ring_lock);
+ /* never allow the last descriptor to be consumed, we need at
+ * least one free at all times to allow for on-the-fly ring
+ * resizing.
+ */
+ while (unlikely(ioat2_ring_space(ioat) <= num_descs)) {
+ if (reshape_ring(ioat, ioat->alloc_order + 1) &&
+ ioat2_ring_space(ioat) > num_descs)
+ break;
+
+ if (printk_ratelimit())
+ dev_dbg(to_dev(chan),
+ "%s: ring full! num_descs: %d (%x:%x:%x)\n",
+ __func__, num_descs, ioat->head, ioat->tail,
+ ioat->issued);
+ spin_unlock_bh(&ioat->ring_lock);
+
+ /* progress reclaim in the allocation failure case we
+ * may be called under bh_disabled so we need to trigger
+ * the timer event directly
+ */
+ spin_lock_bh(&chan->cleanup_lock);
+ if (jiffies > chan->timer.expires &&
+ timer_pending(&chan->timer)) {
+ struct ioatdma_device *device = chan->device;
+
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+ spin_unlock_bh(&chan->cleanup_lock);
+ device->timer_fn((unsigned long) ioat);
+ } else
+ spin_unlock_bh(&chan->cleanup_lock);
+ return -ENOMEM;
+ }
+
+ dev_dbg(to_dev(chan), "%s: num_descs: %d (%x:%x:%x)\n",
+ __func__, num_descs, ioat->head, ioat->tail, ioat->issued);
+
+ *idx = ioat2_desc_alloc(ioat, num_descs);
+ return 0; /* with ioat->ring_lock held */
+}
+
+struct dma_async_tx_descriptor *
+ioat2_dma_prep_memcpy_lock(struct dma_chan *c, dma_addr_t dma_dest,
+ dma_addr_t dma_src, size_t len, unsigned long flags)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_dma_descriptor *hw;
+ struct ioat_ring_ent *desc;
+ dma_addr_t dst = dma_dest;
+ dma_addr_t src = dma_src;
+ size_t total_len = len;
+ int num_descs;
+ u16 idx;
+ int i;
+
+ num_descs = ioat2_xferlen_to_descs(ioat, len);
+ if (likely(num_descs) &&
+ ioat2_alloc_and_lock(&idx, ioat, num_descs) == 0)
+ /* pass */;
+ else
+ return NULL;
+ i = 0;
+ do {
+ size_t copy = min_t(size_t, len, 1 << ioat->xfercap_log);
+
+ desc = ioat2_get_ring_ent(ioat, idx + i);
+ hw = desc->hw;
+
+ hw->size = copy;
+ hw->ctl = 0;
+ hw->src_addr = src;
+ hw->dst_addr = dst;
+
+ len -= copy;
+ dst += copy;
+ src += copy;
+ dump_desc_dbg(ioat, desc);
+ } while (++i < num_descs);
+
+ desc->txd.flags = flags;
+ desc->len = total_len;
+ hw->ctl_f.int_en = !!(flags & DMA_PREP_INTERRUPT);
+ hw->ctl_f.fence = !!(flags & DMA_PREP_FENCE);
+ hw->ctl_f.compl_write = 1;
+ dump_desc_dbg(ioat, desc);
+ /* we leave the channel locked to ensure in order submission */
+
+ return &desc->txd;
+}
+
+/**
+ * ioat2_free_chan_resources - release all the descriptors
+ * @chan: the channel to be cleaned
+ */
+void ioat2_free_chan_resources(struct dma_chan *c)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioatdma_device *device = chan->device;
+ struct ioat_ring_ent *desc;
+ const u16 total_descs = 1 << ioat->alloc_order;
+ int descs;
+ int i;
+
+ /* Before freeing channel resources first check
+ * if they have been previously allocated for this channel.
+ */
+ if (!ioat->ring)
+ return;
+
+ tasklet_disable(&chan->cleanup_task);
+ del_timer_sync(&chan->timer);
+ device->cleanup_tasklet((unsigned long) ioat);
+
+ /* Delay 100ms after reset to allow internal DMA logic to quiesce
+ * before removing DMA descriptor resources.
+ */
+ writeb(IOAT_CHANCMD_RESET,
+ chan->reg_base + IOAT_CHANCMD_OFFSET(chan->device->version));
+ mdelay(100);
+
+ spin_lock_bh(&ioat->ring_lock);
+ descs = ioat2_ring_space(ioat);
+ dev_dbg(to_dev(chan), "freeing %d idle descriptors\n", descs);
+ for (i = 0; i < descs; i++) {
+ desc = ioat2_get_ring_ent(ioat, ioat->head + i);
+ ioat2_free_ring_ent(desc, c);
+ }
+
+ if (descs < total_descs)
+ dev_err(to_dev(chan), "Freeing %d in use descriptors!\n",
+ total_descs - descs);
+
+ for (i = 0; i < total_descs - descs; i++) {
+ desc = ioat2_get_ring_ent(ioat, ioat->tail + i);
+ dump_desc_dbg(ioat, desc);
+ ioat2_free_ring_ent(desc, c);
+ }
+
+ kfree(ioat->ring);
+ ioat->ring = NULL;
+ ioat->alloc_order = 0;
+ pci_pool_free(device->completion_pool, chan->completion,
+ chan->completion_dma);
+ spin_unlock_bh(&ioat->ring_lock);
+
+ chan->last_completion = 0;
+ chan->completion_dma = 0;
+ ioat->pending = 0;
+ ioat->dmacount = 0;
+}
+
+enum dma_status
+ioat2_is_complete(struct dma_chan *c, dma_cookie_t cookie,
+ dma_cookie_t *done, dma_cookie_t *used)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioatdma_device *device = ioat->base.device;
+
+ if (ioat_is_complete(c, cookie, done, used) == DMA_SUCCESS)
+ return DMA_SUCCESS;
+
+ device->cleanup_tasklet((unsigned long) ioat);
+
+ return ioat_is_complete(c, cookie, done, used);
+}
+
+static ssize_t ring_size_show(struct dma_chan *c, char *page)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+
+ return sprintf(page, "%d\n", (1 << ioat->alloc_order) & ~1);
+}
+static struct ioat_sysfs_entry ring_size_attr = __ATTR_RO(ring_size);
+
+static ssize_t ring_active_show(struct dma_chan *c, char *page)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+
+ /* ...taken outside the lock, no need to be precise */
+ return sprintf(page, "%d\n", ioat2_ring_active(ioat));
+}
+static struct ioat_sysfs_entry ring_active_attr = __ATTR_RO(ring_active);
+
+static struct attribute *ioat2_attrs[] = {
+ &ring_size_attr.attr,
+ &ring_active_attr.attr,
+ &ioat_cap_attr.attr,
+ &ioat_version_attr.attr,
+ NULL,
+};
+
+struct kobj_type ioat2_ktype = {
+ .sysfs_ops = &ioat_sysfs_ops,
+ .default_attrs = ioat2_attrs,
+};
+
+int __devinit ioat2_dma_probe(struct ioatdma_device *device, int dca)
+{
+ struct pci_dev *pdev = device->pdev;
+ struct dma_device *dma;
+ struct dma_chan *c;
+ struct ioat_chan_common *chan;
+ int err;
+
+ device->enumerate_channels = ioat2_enumerate_channels;
+ device->cleanup_tasklet = ioat2_cleanup_tasklet;
+ device->timer_fn = ioat2_timer_event;
+ device->self_test = ioat_dma_self_test;
+ dma = &device->common;
+ dma->device_prep_dma_memcpy = ioat2_dma_prep_memcpy_lock;
+ dma->device_issue_pending = ioat2_issue_pending;
+ dma->device_alloc_chan_resources = ioat2_alloc_chan_resources;
+ dma->device_free_chan_resources = ioat2_free_chan_resources;
+ dma->device_is_tx_complete = ioat2_is_complete;
+
+ err = ioat_probe(device);
+ if (err)
+ return err;
+ ioat_set_tcp_copy_break(2048);
+
+ list_for_each_entry(c, &dma->channels, device_node) {
+ chan = to_chan_common(c);
+ writel(IOAT_DCACTRL_CMPL_WRITE_ENABLE | IOAT_DMA_DCA_ANY_CPU,
+ chan->reg_base + IOAT_DCACTRL_OFFSET);
+ }
+
+ err = ioat_register(device);
+ if (err)
+ return err;
+
+ ioat_kobject_add(device, &ioat2_ktype);
+
+ if (dca)
+ device->dca = ioat2_dca_init(pdev, device->reg_base);
+
+ return err;
+}
--- /dev/null
+/*
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called COPYING.
+ */
+#ifndef IOATDMA_V2_H
+#define IOATDMA_V2_H
+
+#include <linux/dmaengine.h>
+#include "dma.h"
+#include "hw.h"
+
+
+extern int ioat_pending_level;
+extern int ioat_ring_alloc_order;
+
+/*
+ * workaround for IOAT ver.3.0 null descriptor issue
+ * (channel returns error when size is 0)
+ */
+#define NULL_DESC_BUFFER_SIZE 1
+
+#define IOAT_MAX_ORDER 16
+#define ioat_get_alloc_order() \
+ (min(ioat_ring_alloc_order, IOAT_MAX_ORDER))
+#define ioat_get_max_alloc_order() \
+ (min(ioat_ring_max_alloc_order, IOAT_MAX_ORDER))
+
+/* struct ioat2_dma_chan - ioat v2 / v3 channel attributes
+ * @base: common ioat channel parameters
+ * @xfercap_log; log2 of channel max transfer length (for fast division)
+ * @head: allocated index
+ * @issued: hardware notification point
+ * @tail: cleanup index
+ * @pending: lock free indicator for issued != head
+ * @dmacount: identical to 'head' except for occasionally resetting to zero
+ * @alloc_order: log2 of the number of allocated descriptors
+ * @ring: software ring buffer implementation of hardware ring
+ * @ring_lock: protects ring attributes
+ */
+struct ioat2_dma_chan {
+ struct ioat_chan_common base;
+ size_t xfercap_log;
+ u16 head;
+ u16 issued;
+ u16 tail;
+ u16 dmacount;
+ u16 alloc_order;
+ int pending;
+ struct ioat_ring_ent **ring;
+ spinlock_t ring_lock;
+};
+
+static inline struct ioat2_dma_chan *to_ioat2_chan(struct dma_chan *c)
+{
+ struct ioat_chan_common *chan = to_chan_common(c);
+
+ return container_of(chan, struct ioat2_dma_chan, base);
+}
+
+static inline u16 ioat2_ring_mask(struct ioat2_dma_chan *ioat)
+{
+ return (1 << ioat->alloc_order) - 1;
+}
+
+/* count of descriptors in flight with the engine */
+static inline u16 ioat2_ring_active(struct ioat2_dma_chan *ioat)
+{
+ return (ioat->head - ioat->tail) & ioat2_ring_mask(ioat);
+}
+
+/* count of descriptors pending submission to hardware */
+static inline u16 ioat2_ring_pending(struct ioat2_dma_chan *ioat)
+{
+ return (ioat->head - ioat->issued) & ioat2_ring_mask(ioat);
+}
+
+static inline u16 ioat2_ring_space(struct ioat2_dma_chan *ioat)
+{
+ u16 num_descs = ioat2_ring_mask(ioat) + 1;
+ u16 active = ioat2_ring_active(ioat);
+
+ BUG_ON(active > num_descs);
+
+ return num_descs - active;
+}
+
+/* assumes caller already checked space */
+static inline u16 ioat2_desc_alloc(struct ioat2_dma_chan *ioat, u16 len)
+{
+ ioat->head += len;
+ return ioat->head - len;
+}
+
+static inline u16 ioat2_xferlen_to_descs(struct ioat2_dma_chan *ioat, size_t len)
+{
+ u16 num_descs = len >> ioat->xfercap_log;
+
+ num_descs += !!(len & ((1 << ioat->xfercap_log) - 1));
+ return num_descs;
+}
+
+/**
+ * struct ioat_ring_ent - wrapper around hardware descriptor
+ * @hw: hardware DMA descriptor (for memcpy)
+ * @fill: hardware fill descriptor
+ * @xor: hardware xor descriptor
+ * @xor_ex: hardware xor extension descriptor
+ * @pq: hardware pq descriptor
+ * @pq_ex: hardware pq extension descriptor
+ * @pqu: hardware pq update descriptor
+ * @raw: hardware raw (un-typed) descriptor
+ * @txd: the generic software descriptor for all engines
+ * @len: total transaction length for unmap
+ * @result: asynchronous result of validate operations
+ * @id: identifier for debug
+ */
+
+struct ioat_ring_ent {
+ union {
+ struct ioat_dma_descriptor *hw;
+ struct ioat_fill_descriptor *fill;
+ struct ioat_xor_descriptor *xor;
+ struct ioat_xor_ext_descriptor *xor_ex;
+ struct ioat_pq_descriptor *pq;
+ struct ioat_pq_ext_descriptor *pq_ex;
+ struct ioat_pq_update_descriptor *pqu;
+ struct ioat_raw_descriptor *raw;
+ };
+ size_t len;
+ struct dma_async_tx_descriptor txd;
+ enum sum_check_flags *result;
+ #ifdef DEBUG
+ int id;
+ #endif
+};
+
+static inline struct ioat_ring_ent *
+ioat2_get_ring_ent(struct ioat2_dma_chan *ioat, u16 idx)
+{
+ return ioat->ring[idx & ioat2_ring_mask(ioat)];
+}
+
+static inline void ioat2_set_chainaddr(struct ioat2_dma_chan *ioat, u64 addr)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+
+ writel(addr & 0x00000000FFFFFFFF,
+ chan->reg_base + IOAT2_CHAINADDR_OFFSET_LOW);
+ writel(addr >> 32,
+ chan->reg_base + IOAT2_CHAINADDR_OFFSET_HIGH);
+}
+
+int __devinit ioat2_dma_probe(struct ioatdma_device *dev, int dca);
+int __devinit ioat3_dma_probe(struct ioatdma_device *dev, int dca);
+struct dca_provider * __devinit ioat2_dca_init(struct pci_dev *pdev, void __iomem *iobase);
+struct dca_provider * __devinit ioat3_dca_init(struct pci_dev *pdev, void __iomem *iobase);
+int ioat2_alloc_and_lock(u16 *idx, struct ioat2_dma_chan *ioat, int num_descs);
+int ioat2_enumerate_channels(struct ioatdma_device *device);
+struct dma_async_tx_descriptor *
+ioat2_dma_prep_memcpy_lock(struct dma_chan *c, dma_addr_t dma_dest,
+ dma_addr_t dma_src, size_t len, unsigned long flags);
+void ioat2_issue_pending(struct dma_chan *chan);
+int ioat2_alloc_chan_resources(struct dma_chan *c);
+void ioat2_free_chan_resources(struct dma_chan *c);
+enum dma_status ioat2_is_complete(struct dma_chan *c, dma_cookie_t cookie,
+ dma_cookie_t *done, dma_cookie_t *used);
+void __ioat2_restart_chan(struct ioat2_dma_chan *ioat);
+bool reshape_ring(struct ioat2_dma_chan *ioat, int order);
+void __ioat2_issue_pending(struct ioat2_dma_chan *ioat);
+void ioat2_cleanup_tasklet(unsigned long data);
+void ioat2_timer_event(unsigned long data);
+extern struct kobj_type ioat2_ktype;
+extern struct kmem_cache *ioat2_cache;
+#endif /* IOATDMA_V2_H */
--- /dev/null
+/*
+ * This file is provided under a dual BSD/GPLv2 license. When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ *
+ * BSD LICENSE
+ *
+ * Copyright(c) 2004-2009 Intel Corporation. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Intel Corporation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/*
+ * Support routines for v3+ hardware
+ */
+
+#include <linux/pci.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include "registers.h"
+#include "hw.h"
+#include "dma.h"
+#include "dma_v2.h"
+
+/* ioat hardware assumes at least two sources for raid operations */
+#define src_cnt_to_sw(x) ((x) + 2)
+#define src_cnt_to_hw(x) ((x) - 2)
+
+/* provide a lookup table for setting the source address in the base or
+ * extended descriptor of an xor or pq descriptor
+ */
+static const u8 xor_idx_to_desc __read_mostly = 0xd0;
+static const u8 xor_idx_to_field[] __read_mostly = { 1, 4, 5, 6, 7, 0, 1, 2 };
+static const u8 pq_idx_to_desc __read_mostly = 0xf8;
+static const u8 pq_idx_to_field[] __read_mostly = { 1, 4, 5, 0, 1, 2, 4, 5 };
+
+static dma_addr_t xor_get_src(struct ioat_raw_descriptor *descs[2], int idx)
+{
+ struct ioat_raw_descriptor *raw = descs[xor_idx_to_desc >> idx & 1];
+
+ return raw->field[xor_idx_to_field[idx]];
+}
+
+static void xor_set_src(struct ioat_raw_descriptor *descs[2],
+ dma_addr_t addr, u32 offset, int idx)
+{
+ struct ioat_raw_descriptor *raw = descs[xor_idx_to_desc >> idx & 1];
+
+ raw->field[xor_idx_to_field[idx]] = addr + offset;
+}
+
+static dma_addr_t pq_get_src(struct ioat_raw_descriptor *descs[2], int idx)
+{
+ struct ioat_raw_descriptor *raw = descs[pq_idx_to_desc >> idx & 1];
+
+ return raw->field[pq_idx_to_field[idx]];
+}
+
+static void pq_set_src(struct ioat_raw_descriptor *descs[2],
+ dma_addr_t addr, u32 offset, u8 coef, int idx)
+{
+ struct ioat_pq_descriptor *pq = (struct ioat_pq_descriptor *) descs[0];
+ struct ioat_raw_descriptor *raw = descs[pq_idx_to_desc >> idx & 1];
+
+ raw->field[pq_idx_to_field[idx]] = addr + offset;
+ pq->coef[idx] = coef;
+}
+
+static void ioat3_dma_unmap(struct ioat2_dma_chan *ioat,
+ struct ioat_ring_ent *desc, int idx)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ struct pci_dev *pdev = chan->device->pdev;
+ size_t len = desc->len;
+ size_t offset = len - desc->hw->size;
+ struct dma_async_tx_descriptor *tx = &desc->txd;
+ enum dma_ctrl_flags flags = tx->flags;
+
+ switch (desc->hw->ctl_f.op) {
+ case IOAT_OP_COPY:
+ if (!desc->hw->ctl_f.null) /* skip 'interrupt' ops */
+ ioat_dma_unmap(chan, flags, len, desc->hw);
+ break;
+ case IOAT_OP_FILL: {
+ struct ioat_fill_descriptor *hw = desc->fill;
+
+ if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP))
+ ioat_unmap(pdev, hw->dst_addr - offset, len,
+ PCI_DMA_FROMDEVICE, flags, 1);
+ break;
+ }
+ case IOAT_OP_XOR_VAL:
+ case IOAT_OP_XOR: {
+ struct ioat_xor_descriptor *xor = desc->xor;
+ struct ioat_ring_ent *ext;
+ struct ioat_xor_ext_descriptor *xor_ex = NULL;
+ int src_cnt = src_cnt_to_sw(xor->ctl_f.src_cnt);
+ struct ioat_raw_descriptor *descs[2];
+ int i;
+
+ if (src_cnt > 5) {
+ ext = ioat2_get_ring_ent(ioat, idx + 1);
+ xor_ex = ext->xor_ex;
+ }
+
+ if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ descs[0] = (struct ioat_raw_descriptor *) xor;
+ descs[1] = (struct ioat_raw_descriptor *) xor_ex;
+ for (i = 0; i < src_cnt; i++) {
+ dma_addr_t src = xor_get_src(descs, i);
+
+ ioat_unmap(pdev, src - offset, len,
+ PCI_DMA_TODEVICE, flags, 0);
+ }
+
+ /* dest is a source in xor validate operations */
+ if (xor->ctl_f.op == IOAT_OP_XOR_VAL) {
+ ioat_unmap(pdev, xor->dst_addr - offset, len,
+ PCI_DMA_TODEVICE, flags, 1);
+ break;
+ }
+ }
+
+ if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP))
+ ioat_unmap(pdev, xor->dst_addr - offset, len,
+ PCI_DMA_FROMDEVICE, flags, 1);
+ break;
+ }
+ case IOAT_OP_PQ_VAL:
+ case IOAT_OP_PQ: {
+ struct ioat_pq_descriptor *pq = desc->pq;
+ struct ioat_ring_ent *ext;
+ struct ioat_pq_ext_descriptor *pq_ex = NULL;
+ int src_cnt = src_cnt_to_sw(pq->ctl_f.src_cnt);
+ struct ioat_raw_descriptor *descs[2];
+ int i;
+
+ if (src_cnt > 3) {
+ ext = ioat2_get_ring_ent(ioat, idx + 1);
+ pq_ex = ext->pq_ex;
+ }
+
+ /* in the 'continue' case don't unmap the dests as sources */
+ if (dmaf_p_disabled_continue(flags))
+ src_cnt--;
+ else if (dmaf_continue(flags))
+ src_cnt -= 3;
+
+ if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ descs[0] = (struct ioat_raw_descriptor *) pq;
+ descs[1] = (struct ioat_raw_descriptor *) pq_ex;
+ for (i = 0; i < src_cnt; i++) {
+ dma_addr_t src = pq_get_src(descs, i);
+
+ ioat_unmap(pdev, src - offset, len,
+ PCI_DMA_TODEVICE, flags, 0);
+ }
+
+ /* the dests are sources in pq validate operations */
+ if (pq->ctl_f.op == IOAT_OP_XOR_VAL) {
+ if (!(flags & DMA_PREP_PQ_DISABLE_P))
+ ioat_unmap(pdev, pq->p_addr - offset,
+ len, PCI_DMA_TODEVICE, flags, 0);
+ if (!(flags & DMA_PREP_PQ_DISABLE_Q))
+ ioat_unmap(pdev, pq->q_addr - offset,
+ len, PCI_DMA_TODEVICE, flags, 0);
+ break;
+ }
+ }
+
+ if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+ if (!(flags & DMA_PREP_PQ_DISABLE_P))
+ ioat_unmap(pdev, pq->p_addr - offset, len,
+ PCI_DMA_BIDIRECTIONAL, flags, 1);
+ if (!(flags & DMA_PREP_PQ_DISABLE_Q))
+ ioat_unmap(pdev, pq->q_addr - offset, len,
+ PCI_DMA_BIDIRECTIONAL, flags, 1);
+ }
+ break;
+ }
+ default:
+ dev_err(&pdev->dev, "%s: unknown op type: %#x\n",
+ __func__, desc->hw->ctl_f.op);
+ }
+}
+
+static bool desc_has_ext(struct ioat_ring_ent *desc)
+{
+ struct ioat_dma_descriptor *hw = desc->hw;
+
+ if (hw->ctl_f.op == IOAT_OP_XOR ||
+ hw->ctl_f.op == IOAT_OP_XOR_VAL) {
+ struct ioat_xor_descriptor *xor = desc->xor;
+
+ if (src_cnt_to_sw(xor->ctl_f.src_cnt) > 5)
+ return true;
+ } else if (hw->ctl_f.op == IOAT_OP_PQ ||
+ hw->ctl_f.op == IOAT_OP_PQ_VAL) {
+ struct ioat_pq_descriptor *pq = desc->pq;
+
+ if (src_cnt_to_sw(pq->ctl_f.src_cnt) > 3)
+ return true;
+ }
+
+ return false;
+}
+
+/**
+ * __cleanup - reclaim used descriptors
+ * @ioat: channel (ring) to clean
+ *
+ * The difference from the dma_v2.c __cleanup() is that this routine
+ * handles extended descriptors and dma-unmapping raid operations.
+ */
+static void __cleanup(struct ioat2_dma_chan *ioat, unsigned long phys_complete)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioat_ring_ent *desc;
+ bool seen_current = false;
+ u16 active;
+ int i;
+
+ dev_dbg(to_dev(chan), "%s: head: %#x tail: %#x issued: %#x\n",
+ __func__, ioat->head, ioat->tail, ioat->issued);
+
+ active = ioat2_ring_active(ioat);
+ for (i = 0; i < active && !seen_current; i++) {
+ struct dma_async_tx_descriptor *tx;
+
+ prefetch(ioat2_get_ring_ent(ioat, ioat->tail + i + 1));
+ desc = ioat2_get_ring_ent(ioat, ioat->tail + i);
+ dump_desc_dbg(ioat, desc);
+ tx = &desc->txd;
+ if (tx->cookie) {
+ chan->completed_cookie = tx->cookie;
+ ioat3_dma_unmap(ioat, desc, ioat->tail + i);
+ tx->cookie = 0;
+ if (tx->callback) {
+ tx->callback(tx->callback_param);
+ tx->callback = NULL;
+ }
+ }
+
+ if (tx->phys == phys_complete)
+ seen_current = true;
+
+ /* skip extended descriptors */
+ if (desc_has_ext(desc)) {
+ BUG_ON(i + 1 >= active);
+ i++;
+ }
+ }
+ ioat->tail += i;
+ BUG_ON(!seen_current); /* no active descs have written a completion? */
+ chan->last_completion = phys_complete;
+ if (ioat->head == ioat->tail) {
+ dev_dbg(to_dev(chan), "%s: cancel completion timeout\n",
+ __func__);
+ clear_bit(IOAT_COMPLETION_PENDING, &chan->state);
+ mod_timer(&chan->timer, jiffies + IDLE_TIMEOUT);
+ }
+}
+
+static void ioat3_cleanup(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ unsigned long phys_complete;
+
+ prefetch(chan->completion);
+
+ if (!spin_trylock_bh(&chan->cleanup_lock))
+ return;
+
+ if (!ioat_cleanup_preamble(chan, &phys_complete)) {
+ spin_unlock_bh(&chan->cleanup_lock);
+ return;
+ }
+
+ if (!spin_trylock_bh(&ioat->ring_lock)) {
+ spin_unlock_bh(&chan->cleanup_lock);
+ return;
+ }
+
+ __cleanup(ioat, phys_complete);
+
+ spin_unlock_bh(&ioat->ring_lock);
+ spin_unlock_bh(&chan->cleanup_lock);
+}
+
+static void ioat3_cleanup_tasklet(unsigned long data)
+{
+ struct ioat2_dma_chan *ioat = (void *) data;
+
+ ioat3_cleanup(ioat);
+ writew(IOAT_CHANCTRL_RUN | IOAT3_CHANCTRL_COMPL_DCA_EN,
+ ioat->base.reg_base + IOAT_CHANCTRL_OFFSET);
+}
+
+static void ioat3_restart_channel(struct ioat2_dma_chan *ioat)
+{
+ struct ioat_chan_common *chan = &ioat->base;
+ unsigned long phys_complete;
+ u32 status;
+
+ status = ioat_chansts(chan);
+ if (is_ioat_active(status) || is_ioat_idle(status))
+ ioat_suspend(chan);
+ while (is_ioat_active(status) || is_ioat_idle(status)) {
+ status = ioat_chansts(chan);
+ cpu_relax();
+ }
+
+ if (ioat_cleanup_preamble(chan, &phys_complete))
+ __cleanup(ioat, phys_complete);
+
+ __ioat2_restart_chan(ioat);
+}
+
+static void ioat3_timer_event(unsigned long data)
+{
+ struct ioat2_dma_chan *ioat = (void *) data;
+ struct ioat_chan_common *chan = &ioat->base;
+
+ spin_lock_bh(&chan->cleanup_lock);
+ if (test_bit(IOAT_COMPLETION_PENDING, &chan->state)) {
+ unsigned long phys_complete;
+ u64 status;
+
+ spin_lock_bh(&ioat->ring_lock);
+ status = ioat_chansts(chan);
+
+ /* when halted due to errors check for channel
+ * programming errors before advancing the completion state
+ */
+ if (is_ioat_halted(status)) {
+ u32 chanerr;
+
+ chanerr = readl(chan->reg_base + IOAT_CHANERR_OFFSET);
+ BUG_ON(is_ioat_bug(chanerr));
+ }
+
+ /* if we haven't made progress and we have already
+ * acknowledged a pending completion once, then be more
+ * forceful with a restart
+ */
+ if (ioat_cleanup_preamble(chan, &phys_complete))
+ __cleanup(ioat, phys_complete);
+ else if (test_bit(IOAT_COMPLETION_ACK, &chan->state))
+ ioat3_restart_channel(ioat);
+ else {
+ set_bit(IOAT_COMPLETION_ACK, &chan->state);
+ mod_timer(&chan->timer, jiffies + COMPLETION_TIMEOUT);
+ }
+ spin_unlock_bh(&ioat->ring_lock);
+ } else {
+ u16 active;
+
+ /* if the ring is idle, empty, and oversized try to step
+ * down the size
+ */
+ spin_lock_bh(&ioat->ring_lock);
+ active = ioat2_ring_active(ioat);
+ if (active == 0 && ioat->alloc_order > ioat_get_alloc_order())
+ reshape_ring(ioat, ioat->alloc_order-1);
+ spin_unlock_bh(&ioat->ring_lock);
+
+ /* keep shrinking until we get back to our minimum
+ * default size
+ */
+ if (ioat->alloc_order > ioat_get_alloc_order())
+ mod_timer(&chan->timer, jiffies + IDLE_TIMEOUT);
+ }
+ spin_unlock_bh(&chan->cleanup_lock);
+}
+
+static enum dma_status
+ioat3_is_complete(struct dma_chan *c, dma_cookie_t cookie,
+ dma_cookie_t *done, dma_cookie_t *used)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+
+ if (ioat_is_complete(c, cookie, done, used) == DMA_SUCCESS)
+ return DMA_SUCCESS;
+
+ ioat3_cleanup(ioat);
+
+ return ioat_is_complete(c, cookie, done, used);
+}
+
+static struct dma_async_tx_descriptor *
+ioat3_prep_memset_lock(struct dma_chan *c, dma_addr_t dest, int value,
+ size_t len, unsigned long flags)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_ring_ent *desc;
+ size_t total_len = len;
+ struct ioat_fill_descriptor *fill;
+ int num_descs;
+ u64 src_data = (0x0101010101010101ULL) * (value & 0xff);
+ u16 idx;
+ int i;
+
+ num_descs = ioat2_xferlen_to_descs(ioat, len);
+ if (likely(num_descs) &&
+ ioat2_alloc_and_lock(&idx, ioat, num_descs) == 0)
+ /* pass */;
+ else
+ return NULL;
+ i = 0;
+ do {
+ size_t xfer_size = min_t(size_t, len, 1 << ioat->xfercap_log);
+
+ desc = ioat2_get_ring_ent(ioat, idx + i);
+ fill = desc->fill;
+
+ fill->size = xfer_size;
+ fill->src_data = src_data;
+ fill->dst_addr = dest;
+ fill->ctl = 0;
+ fill->ctl_f.op = IOAT_OP_FILL;
+
+ len -= xfer_size;
+ dest += xfer_size;
+ dump_desc_dbg(ioat, desc);
+ } while (++i < num_descs);
+
+ desc->txd.flags = flags;
+ desc->len = total_len;
+ fill->ctl_f.int_en = !!(flags & DMA_PREP_INTERRUPT);
+ fill->ctl_f.fence = !!(flags & DMA_PREP_FENCE);
+ fill->ctl_f.compl_write = 1;
+ dump_desc_dbg(ioat, desc);
+
+ /* we leave the channel locked to ensure in order submission */
+ return &desc->txd;
+}
+
+static struct dma_async_tx_descriptor *
+__ioat3_prep_xor_lock(struct dma_chan *c, enum sum_check_flags *result,
+ dma_addr_t dest, dma_addr_t *src, unsigned int src_cnt,
+ size_t len, unsigned long flags)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_ring_ent *compl_desc;
+ struct ioat_ring_ent *desc;
+ struct ioat_ring_ent *ext;
+ size_t total_len = len;
+ struct ioat_xor_descriptor *xor;
+ struct ioat_xor_ext_descriptor *xor_ex = NULL;
+ struct ioat_dma_descriptor *hw;
+ u32 offset = 0;
+ int num_descs;
+ int with_ext;
+ int i;
+ u16 idx;
+ u8 op = result ? IOAT_OP_XOR_VAL : IOAT_OP_XOR;
+
+ BUG_ON(src_cnt < 2);
+
+ num_descs = ioat2_xferlen_to_descs(ioat, len);
+ /* we need 2x the number of descriptors to cover greater than 5
+ * sources
+ */
+ if (src_cnt > 5) {
+ with_ext = 1;
+ num_descs *= 2;
+ } else
+ with_ext = 0;
+
+ /* completion writes from the raid engine may pass completion
+ * writes from the legacy engine, so we need one extra null
+ * (legacy) descriptor to ensure all completion writes arrive in
+ * order.
+ */
+ if (likely(num_descs) &&
+ ioat2_alloc_and_lock(&idx, ioat, num_descs+1) == 0)
+ /* pass */;
+ else
+ return NULL;
+ i = 0;
+ do {
+ struct ioat_raw_descriptor *descs[2];
+ size_t xfer_size = min_t(size_t, len, 1 << ioat->xfercap_log);
+ int s;
+
+ desc = ioat2_get_ring_ent(ioat, idx + i);
+ xor = desc->xor;
+
+ /* save a branch by unconditionally retrieving the
+ * extended descriptor xor_set_src() knows to not write
+ * to it in the single descriptor case
+ */
+ ext = ioat2_get_ring_ent(ioat, idx + i + 1);
+ xor_ex = ext->xor_ex;
+
+ descs[0] = (struct ioat_raw_descriptor *) xor;
+ descs[1] = (struct ioat_raw_descriptor *) xor_ex;
+ for (s = 0; s < src_cnt; s++)
+ xor_set_src(descs, src[s], offset, s);
+ xor->size = xfer_size;
+ xor->dst_addr = dest + offset;
+ xor->ctl = 0;
+ xor->ctl_f.op = op;
+ xor->ctl_f.src_cnt = src_cnt_to_hw(src_cnt);
+
+ len -= xfer_size;
+ offset += xfer_size;
+ dump_desc_dbg(ioat, desc);
+ } while ((i += 1 + with_ext) < num_descs);
+
+ /* last xor descriptor carries the unmap parameters and fence bit */
+ desc->txd.flags = flags;
+ desc->len = total_len;
+ if (result)
+ desc->result = result;
+ xor->ctl_f.fence = !!(flags & DMA_PREP_FENCE);
+
+ /* completion descriptor carries interrupt bit */
+ compl_desc = ioat2_get_ring_ent(ioat, idx + i);
+ compl_desc->txd.flags = flags & DMA_PREP_INTERRUPT;
+ hw = compl_desc->hw;
+ hw->ctl = 0;
+ hw->ctl_f.null = 1;
+ hw->ctl_f.int_en = !!(flags & DMA_PREP_INTERRUPT);
+ hw->ctl_f.compl_write = 1;
+ hw->size = NULL_DESC_BUFFER_SIZE;
+ dump_desc_dbg(ioat, compl_desc);
+
+ /* we leave the channel locked to ensure in order submission */
+ return &desc->txd;
+}
+
+static struct dma_async_tx_descriptor *
+ioat3_prep_xor(struct dma_chan *chan, dma_addr_t dest, dma_addr_t *src,
+ unsigned int src_cnt, size_t len, unsigned long flags)
+{
+ return __ioat3_prep_xor_lock(chan, NULL, dest, src, src_cnt, len, flags);
+}
+
+struct dma_async_tx_descriptor *
+ioat3_prep_xor_val(struct dma_chan *chan, dma_addr_t *src,
+ unsigned int src_cnt, size_t len,
+ enum sum_check_flags *result, unsigned long flags)
+{
+ /* the cleanup routine only sets bits on validate failure, it
+ * does not clear bits on validate success... so clear it here
+ */
+ *result = 0;
+
+ return __ioat3_prep_xor_lock(chan, result, src[0], &src[1],
+ src_cnt - 1, len, flags);
+}
+
+static void
+dump_pq_desc_dbg(struct ioat2_dma_chan *ioat, struct ioat_ring_ent *desc, struct ioat_ring_ent *ext)
+{
+ struct device *dev = to_dev(&ioat->base);
+ struct ioat_pq_descriptor *pq = desc->pq;
+ struct ioat_pq_ext_descriptor *pq_ex = ext ? ext->pq_ex : NULL;
+ struct ioat_raw_descriptor *descs[] = { (void *) pq, (void *) pq_ex };
+ int src_cnt = src_cnt_to_sw(pq->ctl_f.src_cnt);
+ int i;
+
+ dev_dbg(dev, "desc[%d]: (%#llx->%#llx) flags: %#x"
+ " sz: %#x ctl: %#x (op: %d int: %d compl: %d pq: '%s%s' src_cnt: %d)\n",
+ desc_id(desc), (unsigned long long) desc->txd.phys,
+ (unsigned long long) (pq_ex ? pq_ex->next : pq->next),
+ desc->txd.flags, pq->size, pq->ctl, pq->ctl_f.op, pq->ctl_f.int_en,
+ pq->ctl_f.compl_write,
+ pq->ctl_f.p_disable ? "" : "p", pq->ctl_f.q_disable ? "" : "q",
+ pq->ctl_f.src_cnt);
+ for (i = 0; i < src_cnt; i++)
+ dev_dbg(dev, "\tsrc[%d]: %#llx coef: %#x\n", i,
+ (unsigned long long) pq_get_src(descs, i), pq->coef[i]);
+ dev_dbg(dev, "\tP: %#llx\n", pq->p_addr);
+ dev_dbg(dev, "\tQ: %#llx\n", pq->q_addr);
+}
+
+static struct dma_async_tx_descriptor *
+__ioat3_prep_pq_lock(struct dma_chan *c, enum sum_check_flags *result,
+ const dma_addr_t *dst, const dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf,
+ size_t len, unsigned long flags)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_chan_common *chan = &ioat->base;
+ struct ioat_ring_ent *compl_desc;
+ struct ioat_ring_ent *desc;
+ struct ioat_ring_ent *ext;
+ size_t total_len = len;
+ struct ioat_pq_descriptor *pq;
+ struct ioat_pq_ext_descriptor *pq_ex = NULL;
+ struct ioat_dma_descriptor *hw;
+ u32 offset = 0;
+ int num_descs;
+ int with_ext;
+ int i, s;
+ u16 idx;
+ u8 op = result ? IOAT_OP_PQ_VAL : IOAT_OP_PQ;
+
+ dev_dbg(to_dev(chan), "%s\n", __func__);
+ /* the engine requires at least two sources (we provide
+ * at least 1 implied source in the DMA_PREP_CONTINUE case)
+ */
+ BUG_ON(src_cnt + dmaf_continue(flags) < 2);
+
+ num_descs = ioat2_xferlen_to_descs(ioat, len);
+ /* we need 2x the number of descriptors to cover greater than 3
+ * sources
+ */
+ if (src_cnt > 3 || flags & DMA_PREP_CONTINUE) {
+ with_ext = 1;
+ num_descs *= 2;
+ } else
+ with_ext = 0;
+
+ /* completion writes from the raid engine may pass completion
+ * writes from the legacy engine, so we need one extra null
+ * (legacy) descriptor to ensure all completion writes arrive in
+ * order.
+ */
+ if (likely(num_descs) &&
+ ioat2_alloc_and_lock(&idx, ioat, num_descs+1) == 0)
+ /* pass */;
+ else
+ return NULL;
+ i = 0;
+ do {
+ struct ioat_raw_descriptor *descs[2];
+ size_t xfer_size = min_t(size_t, len, 1 << ioat->xfercap_log);
+
+ desc = ioat2_get_ring_ent(ioat, idx + i);
+ pq = desc->pq;
+
+ /* save a branch by unconditionally retrieving the
+ * extended descriptor pq_set_src() knows to not write
+ * to it in the single descriptor case
+ */
+ ext = ioat2_get_ring_ent(ioat, idx + i + with_ext);
+ pq_ex = ext->pq_ex;
+
+ descs[0] = (struct ioat_raw_descriptor *) pq;
+ descs[1] = (struct ioat_raw_descriptor *) pq_ex;
+
+ for (s = 0; s < src_cnt; s++)
+ pq_set_src(descs, src[s], offset, scf[s], s);
+
+ /* see the comment for dma_maxpq in include/linux/dmaengine.h */
+ if (dmaf_p_disabled_continue(flags))
+ pq_set_src(descs, dst[1], offset, 1, s++);
+ else if (dmaf_continue(flags)) {
+ pq_set_src(descs, dst[0], offset, 0, s++);
+ pq_set_src(descs, dst[1], offset, 1, s++);
+ pq_set_src(descs, dst[1], offset, 0, s++);
+ }
+ pq->size = xfer_size;
+ pq->p_addr = dst[0] + offset;
+ pq->q_addr = dst[1] + offset;
+ pq->ctl = 0;
+ pq->ctl_f.op = op;
+ pq->ctl_f.src_cnt = src_cnt_to_hw(s);
+ pq->ctl_f.p_disable = !!(flags & DMA_PREP_PQ_DISABLE_P);
+ pq->ctl_f.q_disable = !!(flags & DMA_PREP_PQ_DISABLE_Q);
+
+ len -= xfer_size;
+ offset += xfer_size;
+ } while ((i += 1 + with_ext) < num_descs);
+
+ /* last pq descriptor carries the unmap parameters and fence bit */
+ desc->txd.flags = flags;
+ desc->len = total_len;
+ if (result)
+ desc->result = result;
+ pq->ctl_f.fence = !!(flags & DMA_PREP_FENCE);
+ dump_pq_desc_dbg(ioat, desc, ext);
+
+ /* completion descriptor carries interrupt bit */
+ compl_desc = ioat2_get_ring_ent(ioat, idx + i);
+ compl_desc->txd.flags = flags & DMA_PREP_INTERRUPT;
+ hw = compl_desc->hw;
+ hw->ctl = 0;
+ hw->ctl_f.null = 1;
+ hw->ctl_f.int_en = !!(flags & DMA_PREP_INTERRUPT);
+ hw->ctl_f.compl_write = 1;
+ hw->size = NULL_DESC_BUFFER_SIZE;
+ dump_desc_dbg(ioat, compl_desc);
+
+ /* we leave the channel locked to ensure in order submission */
+ return &desc->txd;
+}
+
+static struct dma_async_tx_descriptor *
+ioat3_prep_pq(struct dma_chan *chan, dma_addr_t *dst, dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf, size_t len,
+ unsigned long flags)
+{
+ /* handle the single source multiply case from the raid6
+ * recovery path
+ */
+ if (unlikely((flags & DMA_PREP_PQ_DISABLE_P) && src_cnt == 1)) {
+ dma_addr_t single_source[2];
+ unsigned char single_source_coef[2];
+
+ BUG_ON(flags & DMA_PREP_PQ_DISABLE_Q);
+ single_source[0] = src[0];
+ single_source[1] = src[0];
+ single_source_coef[0] = scf[0];
+ single_source_coef[1] = 0;
+
+ return __ioat3_prep_pq_lock(chan, NULL, dst, single_source, 2,
+ single_source_coef, len, flags);
+ } else
+ return __ioat3_prep_pq_lock(chan, NULL, dst, src, src_cnt, scf,
+ len, flags);
+}
+
+struct dma_async_tx_descriptor *
+ioat3_prep_pq_val(struct dma_chan *chan, dma_addr_t *pq, dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf, size_t len,
+ enum sum_check_flags *pqres, unsigned long flags)
+{
+ /* the cleanup routine only sets bits on validate failure, it
+ * does not clear bits on validate success... so clear it here
+ */
+ *pqres = 0;
+
+ return __ioat3_prep_pq_lock(chan, pqres, pq, src, src_cnt, scf, len,
+ flags);
+}
+
+static struct dma_async_tx_descriptor *
+ioat3_prep_pqxor(struct dma_chan *chan, dma_addr_t dst, dma_addr_t *src,
+ unsigned int src_cnt, size_t len, unsigned long flags)
+{
+ unsigned char scf[src_cnt];
+ dma_addr_t pq[2];
+
+ memset(scf, 0, src_cnt);
+ flags |= DMA_PREP_PQ_DISABLE_Q;
+ pq[0] = dst;
+ pq[1] = ~0;
+
+ return __ioat3_prep_pq_lock(chan, NULL, pq, src, src_cnt, scf, len,
+ flags);
+}
+
+struct dma_async_tx_descriptor *
+ioat3_prep_pqxor_val(struct dma_chan *chan, dma_addr_t *src,
+ unsigned int src_cnt, size_t len,
+ enum sum_check_flags *result, unsigned long flags)
+{
+ unsigned char scf[src_cnt];
+ dma_addr_t pq[2];
+
+ /* the cleanup routine only sets bits on validate failure, it
+ * does not clear bits on validate success... so clear it here
+ */
+ *result = 0;
+
+ memset(scf, 0, src_cnt);
+ flags |= DMA_PREP_PQ_DISABLE_Q;
+ pq[0] = src[0];
+ pq[1] = ~0;
+
+ return __ioat3_prep_pq_lock(chan, result, pq, &src[1], src_cnt - 1, scf,
+ len, flags);
+}
+
+static struct dma_async_tx_descriptor *
+ioat3_prep_interrupt_lock(struct dma_chan *c, unsigned long flags)
+{
+ struct ioat2_dma_chan *ioat = to_ioat2_chan(c);
+ struct ioat_ring_ent *desc;
+ struct ioat_dma_descriptor *hw;
+ u16 idx;
+
+ if (ioat2_alloc_and_lock(&idx, ioat, 1) == 0)
+ desc = ioat2_get_ring_ent(ioat, idx);
+ else
+ return NULL;
+
+ hw = desc->hw;
+ hw->ctl = 0;
+ hw->ctl_f.null = 1;
+ hw->ctl_f.int_en = 1;
+ hw->ctl_f.fence = !!(flags & DMA_PREP_FENCE);
+ hw->ctl_f.compl_write = 1;
+ hw->size = NULL_DESC_BUFFER_SIZE;
+ hw->src_addr = 0;
+ hw->dst_addr = 0;
+
+ desc->txd.flags = flags;
+ desc->len = 1;
+
+ dump_desc_dbg(ioat, desc);
+
+ /* we leave the channel locked to ensure in order submission */
+ return &desc->txd;
+}
+
+static void __devinit ioat3_dma_test_callback(void *dma_async_param)
+{
+ struct completion *cmp = dma_async_param;
+
+ complete(cmp);
+}
+
+#define IOAT_NUM_SRC_TEST 6 /* must be <= 8 */
+static int __devinit ioat_xor_val_self_test(struct ioatdma_device *device)
+{
+ int i, src_idx;
+ struct page *dest;
+ struct page *xor_srcs[IOAT_NUM_SRC_TEST];
+ struct page *xor_val_srcs[IOAT_NUM_SRC_TEST + 1];
+ dma_addr_t dma_srcs[IOAT_NUM_SRC_TEST + 1];
+ dma_addr_t dma_addr, dest_dma;
+ struct dma_async_tx_descriptor *tx;
+ struct dma_chan *dma_chan;
+ dma_cookie_t cookie;
+ u8 cmp_byte = 0;
+ u32 cmp_word;
+ u32 xor_val_result;
+ int err = 0;
+ struct completion cmp;
+ unsigned long tmo;
+ struct device *dev = &device->pdev->dev;
+ struct dma_device *dma = &device->common;
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ if (!dma_has_cap(DMA_XOR, dma->cap_mask))
+ return 0;
+
+ for (src_idx = 0; src_idx < IOAT_NUM_SRC_TEST; src_idx++) {
+ xor_srcs[src_idx] = alloc_page(GFP_KERNEL);
+ if (!xor_srcs[src_idx]) {
+ while (src_idx--)
+ __free_page(xor_srcs[src_idx]);
+ return -ENOMEM;
+ }
+ }
+
+ dest = alloc_page(GFP_KERNEL);
+ if (!dest) {
+ while (src_idx--)
+ __free_page(xor_srcs[src_idx]);
+ return -ENOMEM;
+ }
+
+ /* Fill in src buffers */
+ for (src_idx = 0; src_idx < IOAT_NUM_SRC_TEST; src_idx++) {
+ u8 *ptr = page_address(xor_srcs[src_idx]);
+ for (i = 0; i < PAGE_SIZE; i++)
+ ptr[i] = (1 << src_idx);
+ }
+
+ for (src_idx = 0; src_idx < IOAT_NUM_SRC_TEST; src_idx++)
+ cmp_byte ^= (u8) (1 << src_idx);
+
+ cmp_word = (cmp_byte << 24) | (cmp_byte << 16) |
+ (cmp_byte << 8) | cmp_byte;
+
+ memset(page_address(dest), 0, PAGE_SIZE);
+
+ dma_chan = container_of(dma->channels.next, struct dma_chan,
+ device_node);
+ if (dma->device_alloc_chan_resources(dma_chan) < 1) {
+ err = -ENODEV;
+ goto out;
+ }
+
+ /* test xor */
+ dest_dma = dma_map_page(dev, dest, 0, PAGE_SIZE, DMA_FROM_DEVICE);
+ for (i = 0; i < IOAT_NUM_SRC_TEST; i++)
+ dma_srcs[i] = dma_map_page(dev, xor_srcs[i], 0, PAGE_SIZE,
+ DMA_TO_DEVICE);
+ tx = dma->device_prep_dma_xor(dma_chan, dest_dma, dma_srcs,
+ IOAT_NUM_SRC_TEST, PAGE_SIZE,
+ DMA_PREP_INTERRUPT);
+
+ if (!tx) {
+ dev_err(dev, "Self-test xor prep failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ async_tx_ack(tx);
+ init_completion(&cmp);
+ tx->callback = ioat3_dma_test_callback;
+ tx->callback_param = &cmp;
+ cookie = tx->tx_submit(tx);
+ if (cookie < 0) {
+ dev_err(dev, "Self-test xor setup failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ dma->device_issue_pending(dma_chan);
+
+ tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+
+ if (dma->device_is_tx_complete(dma_chan, cookie, NULL, NULL) != DMA_SUCCESS) {
+ dev_err(dev, "Self-test xor timed out\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ dma_sync_single_for_cpu(dev, dest_dma, PAGE_SIZE, DMA_FROM_DEVICE);
+ for (i = 0; i < (PAGE_SIZE / sizeof(u32)); i++) {
+ u32 *ptr = page_address(dest);
+ if (ptr[i] != cmp_word) {
+ dev_err(dev, "Self-test xor failed compare\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ }
+ dma_sync_single_for_device(dev, dest_dma, PAGE_SIZE, DMA_TO_DEVICE);
+
+ /* skip validate if the capability is not present */
+ if (!dma_has_cap(DMA_XOR_VAL, dma_chan->device->cap_mask))
+ goto free_resources;
+
+ /* validate the sources with the destintation page */
+ for (i = 0; i < IOAT_NUM_SRC_TEST; i++)
+ xor_val_srcs[i] = xor_srcs[i];
+ xor_val_srcs[i] = dest;
+
+ xor_val_result = 1;
+
+ for (i = 0; i < IOAT_NUM_SRC_TEST + 1; i++)
+ dma_srcs[i] = dma_map_page(dev, xor_val_srcs[i], 0, PAGE_SIZE,
+ DMA_TO_DEVICE);
+ tx = dma->device_prep_dma_xor_val(dma_chan, dma_srcs,
+ IOAT_NUM_SRC_TEST + 1, PAGE_SIZE,
+ &xor_val_result, DMA_PREP_INTERRUPT);
+ if (!tx) {
+ dev_err(dev, "Self-test zero prep failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ async_tx_ack(tx);
+ init_completion(&cmp);
+ tx->callback = ioat3_dma_test_callback;
+ tx->callback_param = &cmp;
+ cookie = tx->tx_submit(tx);
+ if (cookie < 0) {
+ dev_err(dev, "Self-test zero setup failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ dma->device_issue_pending(dma_chan);
+
+ tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+
+ if (dma->device_is_tx_complete(dma_chan, cookie, NULL, NULL) != DMA_SUCCESS) {
+ dev_err(dev, "Self-test validate timed out\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ if (xor_val_result != 0) {
+ dev_err(dev, "Self-test validate failed compare\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ /* skip memset if the capability is not present */
+ if (!dma_has_cap(DMA_MEMSET, dma_chan->device->cap_mask))
+ goto free_resources;
+
+ /* test memset */
+ dma_addr = dma_map_page(dev, dest, 0,
+ PAGE_SIZE, DMA_FROM_DEVICE);
+ tx = dma->device_prep_dma_memset(dma_chan, dma_addr, 0, PAGE_SIZE,
+ DMA_PREP_INTERRUPT);
+ if (!tx) {
+ dev_err(dev, "Self-test memset prep failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ async_tx_ack(tx);
+ init_completion(&cmp);
+ tx->callback = ioat3_dma_test_callback;
+ tx->callback_param = &cmp;
+ cookie = tx->tx_submit(tx);
+ if (cookie < 0) {
+ dev_err(dev, "Self-test memset setup failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ dma->device_issue_pending(dma_chan);
+
+ tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+
+ if (dma->device_is_tx_complete(dma_chan, cookie, NULL, NULL) != DMA_SUCCESS) {
+ dev_err(dev, "Self-test memset timed out\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ for (i = 0; i < PAGE_SIZE/sizeof(u32); i++) {
+ u32 *ptr = page_address(dest);
+ if (ptr[i]) {
+ dev_err(dev, "Self-test memset failed compare\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ }
+
+ /* test for non-zero parity sum */
+ xor_val_result = 0;
+ for (i = 0; i < IOAT_NUM_SRC_TEST + 1; i++)
+ dma_srcs[i] = dma_map_page(dev, xor_val_srcs[i], 0, PAGE_SIZE,
+ DMA_TO_DEVICE);
+ tx = dma->device_prep_dma_xor_val(dma_chan, dma_srcs,
+ IOAT_NUM_SRC_TEST + 1, PAGE_SIZE,
+ &xor_val_result, DMA_PREP_INTERRUPT);
+ if (!tx) {
+ dev_err(dev, "Self-test 2nd zero prep failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ async_tx_ack(tx);
+ init_completion(&cmp);
+ tx->callback = ioat3_dma_test_callback;
+ tx->callback_param = &cmp;
+ cookie = tx->tx_submit(tx);
+ if (cookie < 0) {
+ dev_err(dev, "Self-test 2nd zero setup failed\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ dma->device_issue_pending(dma_chan);
+
+ tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+
+ if (dma->device_is_tx_complete(dma_chan, cookie, NULL, NULL) != DMA_SUCCESS) {
+ dev_err(dev, "Self-test 2nd validate timed out\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ if (xor_val_result != SUM_CHECK_P_RESULT) {
+ dev_err(dev, "Self-test validate failed compare\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+free_resources:
+ dma->device_free_chan_resources(dma_chan);
+out:
+ src_idx = IOAT_NUM_SRC_TEST;
+ while (src_idx--)
+ __free_page(xor_srcs[src_idx]);
+ __free_page(dest);
+ return err;
+}
+
+static int __devinit ioat3_dma_self_test(struct ioatdma_device *device)
+{
+ int rc = ioat_dma_self_test(device);
+
+ if (rc)
+ return rc;
+
+ rc = ioat_xor_val_self_test(device);
+ if (rc)
+ return rc;
+
+ return 0;
+}
+
+int __devinit ioat3_dma_probe(struct ioatdma_device *device, int dca)
+{
+ struct pci_dev *pdev = device->pdev;
+ struct dma_device *dma;
+ struct dma_chan *c;
+ struct ioat_chan_common *chan;
+ bool is_raid_device = false;
+ int err;
+ u16 dev_id;
+ u32 cap;
+
+ device->enumerate_channels = ioat2_enumerate_channels;
+ device->self_test = ioat3_dma_self_test;
+ dma = &device->common;
+ dma->device_prep_dma_memcpy = ioat2_dma_prep_memcpy_lock;
+ dma->device_issue_pending = ioat2_issue_pending;
+ dma->device_alloc_chan_resources = ioat2_alloc_chan_resources;
+ dma->device_free_chan_resources = ioat2_free_chan_resources;
+
+ dma_cap_set(DMA_INTERRUPT, dma->cap_mask);
+ dma->device_prep_dma_interrupt = ioat3_prep_interrupt_lock;
+
+ cap = readl(device->reg_base + IOAT_DMA_CAP_OFFSET);
+ if (cap & IOAT_CAP_XOR) {
+ is_raid_device = true;
+ dma->max_xor = 8;
+ dma->xor_align = 2;
+
+ dma_cap_set(DMA_XOR, dma->cap_mask);
+ dma->device_prep_dma_xor = ioat3_prep_xor;
+
+ dma_cap_set(DMA_XOR_VAL, dma->cap_mask);
+ dma->device_prep_dma_xor_val = ioat3_prep_xor_val;
+ }
+ if (cap & IOAT_CAP_PQ) {
+ is_raid_device = true;
+ dma_set_maxpq(dma, 8, 0);
+ dma->pq_align = 2;
+
+ dma_cap_set(DMA_PQ, dma->cap_mask);
+ dma->device_prep_dma_pq = ioat3_prep_pq;
+
+ dma_cap_set(DMA_PQ_VAL, dma->cap_mask);
+ dma->device_prep_dma_pq_val = ioat3_prep_pq_val;
+
+ if (!(cap & IOAT_CAP_XOR)) {
+ dma->max_xor = 8;
+ dma->xor_align = 2;
+
+ dma_cap_set(DMA_XOR, dma->cap_mask);
+ dma->device_prep_dma_xor = ioat3_prep_pqxor;
+
+ dma_cap_set(DMA_XOR_VAL, dma->cap_mask);
+ dma->device_prep_dma_xor_val = ioat3_prep_pqxor_val;
+ }
+ }
+ if (is_raid_device && (cap & IOAT_CAP_FILL_BLOCK)) {
+ dma_cap_set(DMA_MEMSET, dma->cap_mask);
+ dma->device_prep_dma_memset = ioat3_prep_memset_lock;
+ }
+
+
+ if (is_raid_device) {
+ dma->device_is_tx_complete = ioat3_is_complete;
+ device->cleanup_tasklet = ioat3_cleanup_tasklet;
+ device->timer_fn = ioat3_timer_event;
+ } else {
+ dma->device_is_tx_complete = ioat2_is_complete;
+ device->cleanup_tasklet = ioat2_cleanup_tasklet;
+ device->timer_fn = ioat2_timer_event;
+ }
+
+ /* -= IOAT ver.3 workarounds =- */
+ /* Write CHANERRMSK_INT with 3E07h to mask out the errors
+ * that can cause stability issues for IOAT ver.3
+ */
+ pci_write_config_dword(pdev, IOAT_PCI_CHANERRMASK_INT_OFFSET, 0x3e07);
+
+ /* Clear DMAUNCERRSTS Cfg-Reg Parity Error status bit
+ * (workaround for spurious config parity error after restart)
+ */
+ pci_read_config_word(pdev, IOAT_PCI_DEVICE_ID_OFFSET, &dev_id);
+ if (dev_id == PCI_DEVICE_ID_INTEL_IOAT_TBG0)
+ pci_write_config_dword(pdev, IOAT_PCI_DMAUNCERRSTS_OFFSET, 0x10);
+
+ err = ioat_probe(device);
+ if (err)
+ return err;
+ ioat_set_tcp_copy_break(262144);
+
+ list_for_each_entry(c, &dma->channels, device_node) {
+ chan = to_chan_common(c);
+ writel(IOAT_DMA_DCA_ANY_CPU,
+ chan->reg_base + IOAT_DCACTRL_OFFSET);
+ }
+
+ err = ioat_register(device);
+ if (err)
+ return err;
+
+ ioat_kobject_add(device, &ioat2_ktype);
+
+ if (dca)
+ device->dca = ioat3_dca_init(pdev, device->reg_base);
+
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called COPYING.
+ */
+#ifndef _IOAT_HW_H_
+#define _IOAT_HW_H_
+
+/* PCI Configuration Space Values */
+#define IOAT_PCI_VID 0x8086
+#define IOAT_MMIO_BAR 0
+
+/* CB device ID's */
+#define IOAT_PCI_DID_5000 0x1A38
+#define IOAT_PCI_DID_CNB 0x360B
+#define IOAT_PCI_DID_SCNB 0x65FF
+#define IOAT_PCI_DID_SNB 0x402F
+
+#define IOAT_PCI_RID 0x00
+#define IOAT_PCI_SVID 0x8086
+#define IOAT_PCI_SID 0x8086
+#define IOAT_VER_1_2 0x12 /* Version 1.2 */
+#define IOAT_VER_2_0 0x20 /* Version 2.0 */
+#define IOAT_VER_3_0 0x30 /* Version 3.0 */
+#define IOAT_VER_3_2 0x32 /* Version 3.2 */
+
+struct ioat_dma_descriptor {
+ uint32_t size;
+ union {
+ uint32_t ctl;
+ struct {
+ unsigned int int_en:1;
+ unsigned int src_snoop_dis:1;
+ unsigned int dest_snoop_dis:1;
+ unsigned int compl_write:1;
+ unsigned int fence:1;
+ unsigned int null:1;
+ unsigned int src_brk:1;
+ unsigned int dest_brk:1;
+ unsigned int bundle:1;
+ unsigned int dest_dca:1;
+ unsigned int hint:1;
+ unsigned int rsvd2:13;
+ #define IOAT_OP_COPY 0x00
+ unsigned int op:8;
+ } ctl_f;
+ };
+ uint64_t src_addr;
+ uint64_t dst_addr;
+ uint64_t next;
+ uint64_t rsv1;
+ uint64_t rsv2;
+ /* store some driver data in an unused portion of the descriptor */
+ union {
+ uint64_t user1;
+ uint64_t tx_cnt;
+ };
+ uint64_t user2;
+};
+
+struct ioat_fill_descriptor {
+ uint32_t size;
+ union {
+ uint32_t ctl;
+ struct {
+ unsigned int int_en:1;
+ unsigned int rsvd:1;
+ unsigned int dest_snoop_dis:1;
+ unsigned int compl_write:1;
+ unsigned int fence:1;
+ unsigned int rsvd2:2;
+ unsigned int dest_brk:1;
+ unsigned int bundle:1;
+ unsigned int rsvd4:15;
+ #define IOAT_OP_FILL 0x01
+ unsigned int op:8;
+ } ctl_f;
+ };
+ uint64_t src_data;
+ uint64_t dst_addr;
+ uint64_t next;
+ uint64_t rsv1;
+ uint64_t next_dst_addr;
+ uint64_t user1;
+ uint64_t user2;
+};
+
+struct ioat_xor_descriptor {
+ uint32_t size;
+ union {
+ uint32_t ctl;
+ struct {
+ unsigned int int_en:1;
+ unsigned int src_snoop_dis:1;
+ unsigned int dest_snoop_dis:1;
+ unsigned int compl_write:1;
+ unsigned int fence:1;
+ unsigned int src_cnt:3;
+ unsigned int bundle:1;
+ unsigned int dest_dca:1;
+ unsigned int hint:1;
+ unsigned int rsvd:13;
+ #define IOAT_OP_XOR 0x87
+ #define IOAT_OP_XOR_VAL 0x88
+ unsigned int op:8;
+ } ctl_f;
+ };
+ uint64_t src_addr;
+ uint64_t dst_addr;
+ uint64_t next;
+ uint64_t src_addr2;
+ uint64_t src_addr3;
+ uint64_t src_addr4;
+ uint64_t src_addr5;
+};
+
+struct ioat_xor_ext_descriptor {
+ uint64_t src_addr6;
+ uint64_t src_addr7;
+ uint64_t src_addr8;
+ uint64_t next;
+ uint64_t rsvd[4];
+};
+
+struct ioat_pq_descriptor {
+ uint32_t size;
+ union {
+ uint32_t ctl;
+ struct {
+ unsigned int int_en:1;
+ unsigned int src_snoop_dis:1;
+ unsigned int dest_snoop_dis:1;
+ unsigned int compl_write:1;
+ unsigned int fence:1;
+ unsigned int src_cnt:3;
+ unsigned int bundle:1;
+ unsigned int dest_dca:1;
+ unsigned int hint:1;
+ unsigned int p_disable:1;
+ unsigned int q_disable:1;
+ unsigned int rsvd:11;
+ #define IOAT_OP_PQ 0x89
+ #define IOAT_OP_PQ_VAL 0x8a
+ unsigned int op:8;
+ } ctl_f;
+ };
+ uint64_t src_addr;
+ uint64_t p_addr;
+ uint64_t next;
+ uint64_t src_addr2;
+ uint64_t src_addr3;
+ uint8_t coef[8];
+ uint64_t q_addr;
+};
+
+struct ioat_pq_ext_descriptor {
+ uint64_t src_addr4;
+ uint64_t src_addr5;
+ uint64_t src_addr6;
+ uint64_t next;
+ uint64_t src_addr7;
+ uint64_t src_addr8;
+ uint64_t rsvd[2];
+};
+
+struct ioat_pq_update_descriptor {
+ uint32_t size;
+ union {
+ uint32_t ctl;
+ struct {
+ unsigned int int_en:1;
+ unsigned int src_snoop_dis:1;
+ unsigned int dest_snoop_dis:1;
+ unsigned int compl_write:1;
+ unsigned int fence:1;
+ unsigned int src_cnt:3;
+ unsigned int bundle:1;
+ unsigned int dest_dca:1;
+ unsigned int hint:1;
+ unsigned int p_disable:1;
+ unsigned int q_disable:1;
+ unsigned int rsvd:3;
+ unsigned int coef:8;
+ #define IOAT_OP_PQ_UP 0x8b
+ unsigned int op:8;
+ } ctl_f;
+ };
+ uint64_t src_addr;
+ uint64_t p_addr;
+ uint64_t next;
+ uint64_t src_addr2;
+ uint64_t p_src;
+ uint64_t q_src;
+ uint64_t q_addr;
+};
+
+struct ioat_raw_descriptor {
+ uint64_t field[8];
+};
+#endif
--- /dev/null
+/*
+ * Intel I/OAT DMA Linux driver
+ * Copyright(c) 2007 - 2009 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ *
+ * The full GNU General Public License is included in this distribution in
+ * the file called "COPYING".
+ *
+ */
+
+/*
+ * This driver supports an Intel I/OAT DMA engine, which does asynchronous
+ * copy operations.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/dca.h>
+#include "dma.h"
+#include "dma_v2.h"
+#include "registers.h"
+#include "hw.h"
+
+MODULE_VERSION(IOAT_DMA_VERSION);
+MODULE_LICENSE("Dual BSD/GPL");
+MODULE_AUTHOR("Intel Corporation");
+
+static struct pci_device_id ioat_pci_tbl[] = {
+ /* I/OAT v1 platforms */
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_CNB) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_SCNB) },
+ { PCI_VDEVICE(UNISYS, PCI_DEVICE_ID_UNISYS_DMA_DIRECTOR) },
+
+ /* I/OAT v2 platforms */
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_SNB) },
+
+ /* I/OAT v3 platforms */
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG0) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG1) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG2) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG3) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG4) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG5) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG6) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_TBG7) },
+
+ /* I/OAT v3.2 platforms */
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF0) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF1) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF2) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF3) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF4) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF5) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF6) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF7) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF8) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IOAT_JSF9) },
+
+ { 0, }
+};
+MODULE_DEVICE_TABLE(pci, ioat_pci_tbl);
+
+static int __devinit ioat_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *id);
+static void __devexit ioat_remove(struct pci_dev *pdev);
+
+static int ioat_dca_enabled = 1;
+module_param(ioat_dca_enabled, int, 0644);
+MODULE_PARM_DESC(ioat_dca_enabled, "control support of dca service (default: 1)");
+
+struct kmem_cache *ioat2_cache;
+
+#define DRV_NAME "ioatdma"
+
+static struct pci_driver ioat_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = ioat_pci_tbl,
+ .probe = ioat_pci_probe,
+ .remove = __devexit_p(ioat_remove),
+};
+
+static struct ioatdma_device *
+alloc_ioatdma(struct pci_dev *pdev, void __iomem *iobase)
+{
+ struct device *dev = &pdev->dev;
+ struct ioatdma_device *d = devm_kzalloc(dev, sizeof(*d), GFP_KERNEL);
+
+ if (!d)
+ return NULL;
+ d->pdev = pdev;
+ d->reg_base = iobase;
+ return d;
+}
+
+static int __devinit ioat_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ void __iomem * const *iomap;
+ struct device *dev = &pdev->dev;
+ struct ioatdma_device *device;
+ int err;
+
+ err = pcim_enable_device(pdev);
+ if (err)
+ return err;
+
+ err = pcim_iomap_regions(pdev, 1 << IOAT_MMIO_BAR, DRV_NAME);
+ if (err)
+ return err;
+ iomap = pcim_iomap_table(pdev);
+ if (!iomap)
+ return -ENOMEM;
+
+ err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
+ if (err)
+ err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (err)
+ return err;
+
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
+ if (err)
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (err)
+ return err;
+
+ device = devm_kzalloc(dev, sizeof(*device), GFP_KERNEL);
+ if (!device)
+ return -ENOMEM;
+
+ pci_set_master(pdev);
+
+ device = alloc_ioatdma(pdev, iomap[IOAT_MMIO_BAR]);
+ if (!device)
+ return -ENOMEM;
+ pci_set_drvdata(pdev, device);
+
+ device->version = readb(device->reg_base + IOAT_VER_OFFSET);
+ if (device->version == IOAT_VER_1_2)
+ err = ioat1_dma_probe(device, ioat_dca_enabled);
+ else if (device->version == IOAT_VER_2_0)
+ err = ioat2_dma_probe(device, ioat_dca_enabled);
+ else if (device->version >= IOAT_VER_3_0)
+ err = ioat3_dma_probe(device, ioat_dca_enabled);
+ else
+ return -ENODEV;
+
+ if (err) {
+ dev_err(dev, "Intel(R) I/OAT DMA Engine init failed\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static void __devexit ioat_remove(struct pci_dev *pdev)
+{
+ struct ioatdma_device *device = pci_get_drvdata(pdev);
+
+ if (!device)
+ return;
+
+ dev_err(&pdev->dev, "Removing dma and dca services\n");
+ if (device->dca) {
+ unregister_dca_provider(device->dca, &pdev->dev);
+ free_dca_provider(device->dca);
+ device->dca = NULL;
+ }
+ ioat_dma_remove(device);
+}
+
+static int __init ioat_init_module(void)
+{
+ int err;
+
+ pr_info("%s: Intel(R) QuickData Technology Driver %s\n",
+ DRV_NAME, IOAT_DMA_VERSION);
+
+ ioat2_cache = kmem_cache_create("ioat2", sizeof(struct ioat_ring_ent),
+ 0, SLAB_HWCACHE_ALIGN, NULL);
+ if (!ioat2_cache)
+ return -ENOMEM;
+
+ err = pci_register_driver(&ioat_pci_driver);
+ if (err)
+ kmem_cache_destroy(ioat2_cache);
+
+ return err;
+}
+module_init(ioat_init_module);
+
+static void __exit ioat_exit_module(void)
+{
+ pci_unregister_driver(&ioat_pci_driver);
+ kmem_cache_destroy(ioat2_cache);
+}
+module_exit(ioat_exit_module);
--- /dev/null
+/*
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; if not, write to the Free Software Foundation, Inc., 59
+ * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ * The full GNU General Public License is included in this distribution in the
+ * file called COPYING.
+ */
+#ifndef _IOAT_REGISTERS_H_
+#define _IOAT_REGISTERS_H_
+
+#define IOAT_PCI_DMACTRL_OFFSET 0x48
+#define IOAT_PCI_DMACTRL_DMA_EN 0x00000001
+#define IOAT_PCI_DMACTRL_MSI_EN 0x00000002
+
+#define IOAT_PCI_DEVICE_ID_OFFSET 0x02
+#define IOAT_PCI_DMAUNCERRSTS_OFFSET 0x148
+#define IOAT_PCI_CHANERRMASK_INT_OFFSET 0x184
+
+/* MMIO Device Registers */
+#define IOAT_CHANCNT_OFFSET 0x00 /* 8-bit */
+
+#define IOAT_XFERCAP_OFFSET 0x01 /* 8-bit */
+#define IOAT_XFERCAP_4KB 12
+#define IOAT_XFERCAP_8KB 13
+#define IOAT_XFERCAP_16KB 14
+#define IOAT_XFERCAP_32KB 15
+#define IOAT_XFERCAP_32GB 0
+
+#define IOAT_GENCTRL_OFFSET 0x02 /* 8-bit */
+#define IOAT_GENCTRL_DEBUG_EN 0x01
+
+#define IOAT_INTRCTRL_OFFSET 0x03 /* 8-bit */
+#define IOAT_INTRCTRL_MASTER_INT_EN 0x01 /* Master Interrupt Enable */
+#define IOAT_INTRCTRL_INT_STATUS 0x02 /* ATTNSTATUS -or- Channel Int */
+#define IOAT_INTRCTRL_INT 0x04 /* INT_STATUS -and- MASTER_INT_EN */
+#define IOAT_INTRCTRL_MSIX_VECTOR_CONTROL 0x08 /* Enable all MSI-X vectors */
+
+#define IOAT_ATTNSTATUS_OFFSET 0x04 /* Each bit is a channel */
+
+#define IOAT_VER_OFFSET 0x08 /* 8-bit */
+#define IOAT_VER_MAJOR_MASK 0xF0
+#define IOAT_VER_MINOR_MASK 0x0F
+#define GET_IOAT_VER_MAJOR(x) (((x) & IOAT_VER_MAJOR_MASK) >> 4)
+#define GET_IOAT_VER_MINOR(x) ((x) & IOAT_VER_MINOR_MASK)
+
+#define IOAT_PERPORTOFFSET_OFFSET 0x0A /* 16-bit */
+
+#define IOAT_INTRDELAY_OFFSET 0x0C /* 16-bit */
+#define IOAT_INTRDELAY_INT_DELAY_MASK 0x3FFF /* Interrupt Delay Time */
+#define IOAT_INTRDELAY_COALESE_SUPPORT 0x8000 /* Interrupt Coalescing Supported */
+
+#define IOAT_DEVICE_STATUS_OFFSET 0x0E /* 16-bit */
+#define IOAT_DEVICE_STATUS_DEGRADED_MODE 0x0001
+#define IOAT_DEVICE_MMIO_RESTRICTED 0x0002
+#define IOAT_DEVICE_MEMORY_BYPASS 0x0004
+#define IOAT_DEVICE_ADDRESS_REMAPPING 0x0008
+
+#define IOAT_DMA_CAP_OFFSET 0x10 /* 32-bit */
+#define IOAT_CAP_PAGE_BREAK 0x00000001
+#define IOAT_CAP_CRC 0x00000002
+#define IOAT_CAP_SKIP_MARKER 0x00000004
+#define IOAT_CAP_DCA 0x00000010
+#define IOAT_CAP_CRC_MOVE 0x00000020
+#define IOAT_CAP_FILL_BLOCK 0x00000040
+#define IOAT_CAP_APIC 0x00000080
+#define IOAT_CAP_XOR 0x00000100
+#define IOAT_CAP_PQ 0x00000200
+
+#define IOAT_CHANNEL_MMIO_SIZE 0x80 /* Each Channel MMIO space is this size */
+
+/* DMA Channel Registers */
+#define IOAT_CHANCTRL_OFFSET 0x00 /* 16-bit Channel Control Register */
+#define IOAT_CHANCTRL_CHANNEL_PRIORITY_MASK 0xF000
+#define IOAT3_CHANCTRL_COMPL_DCA_EN 0x0200
+#define IOAT_CHANCTRL_CHANNEL_IN_USE 0x0100
+#define IOAT_CHANCTRL_DESCRIPTOR_ADDR_SNOOP_CONTROL 0x0020
+#define IOAT_CHANCTRL_ERR_INT_EN 0x0010
+#define IOAT_CHANCTRL_ANY_ERR_ABORT_EN 0x0008
+#define IOAT_CHANCTRL_ERR_COMPLETION_EN 0x0004
+#define IOAT_CHANCTRL_INT_REARM 0x0001
+#define IOAT_CHANCTRL_RUN (IOAT_CHANCTRL_INT_REARM |\
+ IOAT_CHANCTRL_ERR_COMPLETION_EN |\
+ IOAT_CHANCTRL_ANY_ERR_ABORT_EN |\
+ IOAT_CHANCTRL_ERR_INT_EN)
+
+#define IOAT_DMA_COMP_OFFSET 0x02 /* 16-bit DMA channel compatibility */
+#define IOAT_DMA_COMP_V1 0x0001 /* Compatibility with DMA version 1 */
+#define IOAT_DMA_COMP_V2 0x0002 /* Compatibility with DMA version 2 */
+
+
+#define IOAT1_CHANSTS_OFFSET 0x04 /* 64-bit Channel Status Register */
+#define IOAT2_CHANSTS_OFFSET 0x08 /* 64-bit Channel Status Register */
+#define IOAT_CHANSTS_OFFSET(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHANSTS_OFFSET : IOAT2_CHANSTS_OFFSET)
+#define IOAT1_CHANSTS_OFFSET_LOW 0x04
+#define IOAT2_CHANSTS_OFFSET_LOW 0x08
+#define IOAT_CHANSTS_OFFSET_LOW(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHANSTS_OFFSET_LOW : IOAT2_CHANSTS_OFFSET_LOW)
+#define IOAT1_CHANSTS_OFFSET_HIGH 0x08
+#define IOAT2_CHANSTS_OFFSET_HIGH 0x0C
+#define IOAT_CHANSTS_OFFSET_HIGH(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHANSTS_OFFSET_HIGH : IOAT2_CHANSTS_OFFSET_HIGH)
+#define IOAT_CHANSTS_COMPLETED_DESCRIPTOR_ADDR (~0x3fULL)
+#define IOAT_CHANSTS_SOFT_ERR 0x10ULL
+#define IOAT_CHANSTS_UNAFFILIATED_ERR 0x8ULL
+#define IOAT_CHANSTS_STATUS 0x7ULL
+#define IOAT_CHANSTS_ACTIVE 0x0
+#define IOAT_CHANSTS_DONE 0x1
+#define IOAT_CHANSTS_SUSPENDED 0x2
+#define IOAT_CHANSTS_HALTED 0x3
+
+
+
+#define IOAT_CHAN_DMACOUNT_OFFSET 0x06 /* 16-bit DMA Count register */
+
+#define IOAT_DCACTRL_OFFSET 0x30 /* 32 bit Direct Cache Access Control Register */
+#define IOAT_DCACTRL_CMPL_WRITE_ENABLE 0x10000
+#define IOAT_DCACTRL_TARGET_CPU_MASK 0xFFFF /* APIC ID */
+
+/* CB DCA Memory Space Registers */
+#define IOAT_DCAOFFSET_OFFSET 0x14
+/* CB_BAR + IOAT_DCAOFFSET value */
+#define IOAT_DCA_VER_OFFSET 0x00
+#define IOAT_DCA_VER_MAJOR_MASK 0xF0
+#define IOAT_DCA_VER_MINOR_MASK 0x0F
+
+#define IOAT_DCA_COMP_OFFSET 0x02
+#define IOAT_DCA_COMP_V1 0x1
+
+#define IOAT_FSB_CAPABILITY_OFFSET 0x04
+#define IOAT_FSB_CAPABILITY_PREFETCH 0x1
+
+#define IOAT_PCI_CAPABILITY_OFFSET 0x06
+#define IOAT_PCI_CAPABILITY_MEMWR 0x1
+
+#define IOAT_FSB_CAP_ENABLE_OFFSET 0x08
+#define IOAT_FSB_CAP_ENABLE_PREFETCH 0x1
+
+#define IOAT_PCI_CAP_ENABLE_OFFSET 0x0A
+#define IOAT_PCI_CAP_ENABLE_MEMWR 0x1
+
+#define IOAT_APICID_TAG_MAP_OFFSET 0x0C
+#define IOAT_APICID_TAG_MAP_TAG0 0x0000000F
+#define IOAT_APICID_TAG_MAP_TAG0_SHIFT 0
+#define IOAT_APICID_TAG_MAP_TAG1 0x000000F0
+#define IOAT_APICID_TAG_MAP_TAG1_SHIFT 4
+#define IOAT_APICID_TAG_MAP_TAG2 0x00000F00
+#define IOAT_APICID_TAG_MAP_TAG2_SHIFT 8
+#define IOAT_APICID_TAG_MAP_TAG3 0x0000F000
+#define IOAT_APICID_TAG_MAP_TAG3_SHIFT 12
+#define IOAT_APICID_TAG_MAP_TAG4 0x000F0000
+#define IOAT_APICID_TAG_MAP_TAG4_SHIFT 16
+#define IOAT_APICID_TAG_CB2_VALID 0x8080808080
+
+#define IOAT_DCA_GREQID_OFFSET 0x10
+#define IOAT_DCA_GREQID_SIZE 0x04
+#define IOAT_DCA_GREQID_MASK 0xFFFF
+#define IOAT_DCA_GREQID_IGNOREFUN 0x10000000
+#define IOAT_DCA_GREQID_VALID 0x20000000
+#define IOAT_DCA_GREQID_LASTID 0x80000000
+
+#define IOAT3_CSI_CAPABILITY_OFFSET 0x08
+#define IOAT3_CSI_CAPABILITY_PREFETCH 0x1
+
+#define IOAT3_PCI_CAPABILITY_OFFSET 0x0A
+#define IOAT3_PCI_CAPABILITY_MEMWR 0x1
+
+#define IOAT3_CSI_CONTROL_OFFSET 0x0C
+#define IOAT3_CSI_CONTROL_PREFETCH 0x1
+
+#define IOAT3_PCI_CONTROL_OFFSET 0x0E
+#define IOAT3_PCI_CONTROL_MEMWR 0x1
+
+#define IOAT3_APICID_TAG_MAP_OFFSET 0x10
+#define IOAT3_APICID_TAG_MAP_OFFSET_LOW 0x10
+#define IOAT3_APICID_TAG_MAP_OFFSET_HIGH 0x14
+
+#define IOAT3_DCA_GREQID_OFFSET 0x02
+
+#define IOAT1_CHAINADDR_OFFSET 0x0C /* 64-bit Descriptor Chain Address Register */
+#define IOAT2_CHAINADDR_OFFSET 0x10 /* 64-bit Descriptor Chain Address Register */
+#define IOAT_CHAINADDR_OFFSET(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHAINADDR_OFFSET : IOAT2_CHAINADDR_OFFSET)
+#define IOAT1_CHAINADDR_OFFSET_LOW 0x0C
+#define IOAT2_CHAINADDR_OFFSET_LOW 0x10
+#define IOAT_CHAINADDR_OFFSET_LOW(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHAINADDR_OFFSET_LOW : IOAT2_CHAINADDR_OFFSET_LOW)
+#define IOAT1_CHAINADDR_OFFSET_HIGH 0x10
+#define IOAT2_CHAINADDR_OFFSET_HIGH 0x14
+#define IOAT_CHAINADDR_OFFSET_HIGH(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHAINADDR_OFFSET_HIGH : IOAT2_CHAINADDR_OFFSET_HIGH)
+
+#define IOAT1_CHANCMD_OFFSET 0x14 /* 8-bit DMA Channel Command Register */
+#define IOAT2_CHANCMD_OFFSET 0x04 /* 8-bit DMA Channel Command Register */
+#define IOAT_CHANCMD_OFFSET(ver) ((ver) < IOAT_VER_2_0 \
+ ? IOAT1_CHANCMD_OFFSET : IOAT2_CHANCMD_OFFSET)
+#define IOAT_CHANCMD_RESET 0x20
+#define IOAT_CHANCMD_RESUME 0x10
+#define IOAT_CHANCMD_ABORT 0x08
+#define IOAT_CHANCMD_SUSPEND 0x04
+#define IOAT_CHANCMD_APPEND 0x02
+#define IOAT_CHANCMD_START 0x01
+
+#define IOAT_CHANCMP_OFFSET 0x18 /* 64-bit Channel Completion Address Register */
+#define IOAT_CHANCMP_OFFSET_LOW 0x18
+#define IOAT_CHANCMP_OFFSET_HIGH 0x1C
+
+#define IOAT_CDAR_OFFSET 0x20 /* 64-bit Current Descriptor Address Register */
+#define IOAT_CDAR_OFFSET_LOW 0x20
+#define IOAT_CDAR_OFFSET_HIGH 0x24
+
+#define IOAT_CHANERR_OFFSET 0x28 /* 32-bit Channel Error Register */
+#define IOAT_CHANERR_SRC_ADDR_ERR 0x0001
+#define IOAT_CHANERR_DEST_ADDR_ERR 0x0002
+#define IOAT_CHANERR_NEXT_ADDR_ERR 0x0004
+#define IOAT_CHANERR_NEXT_DESC_ALIGN_ERR 0x0008
+#define IOAT_CHANERR_CHAIN_ADDR_VALUE_ERR 0x0010
+#define IOAT_CHANERR_CHANCMD_ERR 0x0020
+#define IOAT_CHANERR_CHIPSET_UNCORRECTABLE_DATA_INTEGRITY_ERR 0x0040
+#define IOAT_CHANERR_DMA_UNCORRECTABLE_DATA_INTEGRITY_ERR 0x0080
+#define IOAT_CHANERR_READ_DATA_ERR 0x0100
+#define IOAT_CHANERR_WRITE_DATA_ERR 0x0200
+#define IOAT_CHANERR_CONTROL_ERR 0x0400
+#define IOAT_CHANERR_LENGTH_ERR 0x0800
+#define IOAT_CHANERR_COMPLETION_ADDR_ERR 0x1000
+#define IOAT_CHANERR_INT_CONFIGURATION_ERR 0x2000
+#define IOAT_CHANERR_SOFT_ERR 0x4000
+#define IOAT_CHANERR_UNAFFILIATED_ERR 0x8000
+#define IOAT_CHANERR_XOR_P_OR_CRC_ERR 0x10000
+#define IOAT_CHANERR_XOR_Q_ERR 0x20000
+#define IOAT_CHANERR_DESCRIPTOR_COUNT_ERR 0x40000
+
+#define IOAT_CHANERR_HANDLE_MASK (IOAT_CHANERR_XOR_P_OR_CRC_ERR | IOAT_CHANERR_XOR_Q_ERR)
+
+#define IOAT_CHANERR_MASK_OFFSET 0x2C /* 32-bit Channel Error Register */
+
+#endif /* _IOAT_REGISTERS_H_ */
+++ /dev/null
-/*
- * Intel I/OAT DMA Linux driver
- * Copyright(c) 2007 - 2009 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- *
- * The full GNU General Public License is included in this distribution in
- * the file called "COPYING".
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/smp.h>
-#include <linux/interrupt.h>
-#include <linux/dca.h>
-
-/* either a kernel change is needed, or we need something like this in kernel */
-#ifndef CONFIG_SMP
-#include <asm/smp.h>
-#undef cpu_physical_id
-#define cpu_physical_id(cpu) (cpuid_ebx(1) >> 24)
-#endif
-
-#include "ioatdma.h"
-#include "ioatdma_registers.h"
-
-/*
- * Bit 7 of a tag map entry is the "valid" bit, if it is set then bits 0:6
- * contain the bit number of the APIC ID to map into the DCA tag. If the valid
- * bit is not set, then the value must be 0 or 1 and defines the bit in the tag.
- */
-#define DCA_TAG_MAP_VALID 0x80
-
-#define DCA3_TAG_MAP_BIT_TO_INV 0x80
-#define DCA3_TAG_MAP_BIT_TO_SEL 0x40
-#define DCA3_TAG_MAP_LITERAL_VAL 0x1
-
-#define DCA_TAG_MAP_MASK 0xDF
-
-/* expected tag map bytes for I/OAT ver.2 */
-#define DCA2_TAG_MAP_BYTE0 0x80
-#define DCA2_TAG_MAP_BYTE1 0x0
-#define DCA2_TAG_MAP_BYTE2 0x81
-#define DCA2_TAG_MAP_BYTE3 0x82
-#define DCA2_TAG_MAP_BYTE4 0x82
-
-/* verify if tag map matches expected values */
-static inline int dca2_tag_map_valid(u8 *tag_map)
-{
- return ((tag_map[0] == DCA2_TAG_MAP_BYTE0) &&
- (tag_map[1] == DCA2_TAG_MAP_BYTE1) &&
- (tag_map[2] == DCA2_TAG_MAP_BYTE2) &&
- (tag_map[3] == DCA2_TAG_MAP_BYTE3) &&
- (tag_map[4] == DCA2_TAG_MAP_BYTE4));
-}
-
-/*
- * "Legacy" DCA systems do not implement the DCA register set in the
- * I/OAT device. Software needs direct support for their tag mappings.
- */
-
-#define APICID_BIT(x) (DCA_TAG_MAP_VALID | (x))
-#define IOAT_TAG_MAP_LEN 8
-
-static u8 ioat_tag_map_BNB[IOAT_TAG_MAP_LEN] = {
- 1, APICID_BIT(1), APICID_BIT(2), APICID_BIT(2), };
-static u8 ioat_tag_map_SCNB[IOAT_TAG_MAP_LEN] = {
- 1, APICID_BIT(1), APICID_BIT(2), APICID_BIT(2), };
-static u8 ioat_tag_map_CNB[IOAT_TAG_MAP_LEN] = {
- 1, APICID_BIT(1), APICID_BIT(3), APICID_BIT(4), APICID_BIT(2), };
-static u8 ioat_tag_map_UNISYS[IOAT_TAG_MAP_LEN] = { 0 };
-
-/* pack PCI B/D/F into a u16 */
-static inline u16 dcaid_from_pcidev(struct pci_dev *pci)
-{
- return (pci->bus->number << 8) | pci->devfn;
-}
-
-static int dca_enabled_in_bios(struct pci_dev *pdev)
-{
- /* CPUID level 9 returns DCA configuration */
- /* Bit 0 indicates DCA enabled by the BIOS */
- unsigned long cpuid_level_9;
- int res;
-
- cpuid_level_9 = cpuid_eax(9);
- res = test_bit(0, &cpuid_level_9);
- if (!res)
- dev_err(&pdev->dev, "DCA is disabled in BIOS\n");
-
- return res;
-}
-
-static int system_has_dca_enabled(struct pci_dev *pdev)
-{
- if (boot_cpu_has(X86_FEATURE_DCA))
- return dca_enabled_in_bios(pdev);
-
- dev_err(&pdev->dev, "boot cpu doesn't have X86_FEATURE_DCA\n");
- return 0;
-}
-
-struct ioat_dca_slot {
- struct pci_dev *pdev; /* requester device */
- u16 rid; /* requester id, as used by IOAT */
-};
-
-#define IOAT_DCA_MAX_REQ 6
-#define IOAT3_DCA_MAX_REQ 2
-
-struct ioat_dca_priv {
- void __iomem *iobase;
- void __iomem *dca_base;
- int max_requesters;
- int requester_count;
- u8 tag_map[IOAT_TAG_MAP_LEN];
- struct ioat_dca_slot req_slots[0];
-};
-
-/* 5000 series chipset DCA Port Requester ID Table Entry Format
- * [15:8] PCI-Express Bus Number
- * [7:3] PCI-Express Device Number
- * [2:0] PCI-Express Function Number
- *
- * 5000 series chipset DCA control register format
- * [7:1] Reserved (0)
- * [0] Ignore Function Number
- */
-
-static int ioat_dca_add_requester(struct dca_provider *dca, struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
- u16 id;
-
- /* This implementation only supports PCI-Express */
- if (dev->bus != &pci_bus_type)
- return -ENODEV;
- pdev = to_pci_dev(dev);
- id = dcaid_from_pcidev(pdev);
-
- if (ioatdca->requester_count == ioatdca->max_requesters)
- return -ENODEV;
-
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == NULL) {
- /* found an empty slot */
- ioatdca->requester_count++;
- ioatdca->req_slots[i].pdev = pdev;
- ioatdca->req_slots[i].rid = id;
- writew(id, ioatdca->dca_base + (i * 4));
- /* make sure the ignore function bit is off */
- writeb(0, ioatdca->dca_base + (i * 4) + 2);
- return i;
- }
- }
- /* Error, ioatdma->requester_count is out of whack */
- return -EFAULT;
-}
-
-static int ioat_dca_remove_requester(struct dca_provider *dca,
- struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
-
- /* This implementation only supports PCI-Express */
- if (dev->bus != &pci_bus_type)
- return -ENODEV;
- pdev = to_pci_dev(dev);
-
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == pdev) {
- writew(0, ioatdca->dca_base + (i * 4));
- ioatdca->req_slots[i].pdev = NULL;
- ioatdca->req_slots[i].rid = 0;
- ioatdca->requester_count--;
- return i;
- }
- }
- return -ENODEV;
-}
-
-static u8 ioat_dca_get_tag(struct dca_provider *dca,
- struct device *dev,
- int cpu)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- int i, apic_id, bit, value;
- u8 entry, tag;
-
- tag = 0;
- apic_id = cpu_physical_id(cpu);
-
- for (i = 0; i < IOAT_TAG_MAP_LEN; i++) {
- entry = ioatdca->tag_map[i];
- if (entry & DCA_TAG_MAP_VALID) {
- bit = entry & ~DCA_TAG_MAP_VALID;
- value = (apic_id & (1 << bit)) ? 1 : 0;
- } else {
- value = entry ? 1 : 0;
- }
- tag |= (value << i);
- }
- return tag;
-}
-
-static int ioat_dca_dev_managed(struct dca_provider *dca,
- struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
-
- pdev = to_pci_dev(dev);
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == pdev)
- return 1;
- }
- return 0;
-}
-
-static struct dca_ops ioat_dca_ops = {
- .add_requester = ioat_dca_add_requester,
- .remove_requester = ioat_dca_remove_requester,
- .get_tag = ioat_dca_get_tag,
- .dev_managed = ioat_dca_dev_managed,
-};
-
-
-struct dca_provider *ioat_dca_init(struct pci_dev *pdev, void __iomem *iobase)
-{
- struct dca_provider *dca;
- struct ioat_dca_priv *ioatdca;
- u8 *tag_map = NULL;
- int i;
- int err;
- u8 version;
- u8 max_requesters;
-
- if (!system_has_dca_enabled(pdev))
- return NULL;
-
- /* I/OAT v1 systems must have a known tag_map to support DCA */
- switch (pdev->vendor) {
- case PCI_VENDOR_ID_INTEL:
- switch (pdev->device) {
- case PCI_DEVICE_ID_INTEL_IOAT:
- tag_map = ioat_tag_map_BNB;
- break;
- case PCI_DEVICE_ID_INTEL_IOAT_CNB:
- tag_map = ioat_tag_map_CNB;
- break;
- case PCI_DEVICE_ID_INTEL_IOAT_SCNB:
- tag_map = ioat_tag_map_SCNB;
- break;
- }
- break;
- case PCI_VENDOR_ID_UNISYS:
- switch (pdev->device) {
- case PCI_DEVICE_ID_UNISYS_DMA_DIRECTOR:
- tag_map = ioat_tag_map_UNISYS;
- break;
- }
- break;
- }
- if (tag_map == NULL)
- return NULL;
-
- version = readb(iobase + IOAT_VER_OFFSET);
- if (version == IOAT_VER_3_0)
- max_requesters = IOAT3_DCA_MAX_REQ;
- else
- max_requesters = IOAT_DCA_MAX_REQ;
-
- dca = alloc_dca_provider(&ioat_dca_ops,
- sizeof(*ioatdca) +
- (sizeof(struct ioat_dca_slot) * max_requesters));
- if (!dca)
- return NULL;
-
- ioatdca = dca_priv(dca);
- ioatdca->max_requesters = max_requesters;
- ioatdca->dca_base = iobase + 0x54;
-
- /* copy over the APIC ID to DCA tag mapping */
- for (i = 0; i < IOAT_TAG_MAP_LEN; i++)
- ioatdca->tag_map[i] = tag_map[i];
-
- err = register_dca_provider(dca, &pdev->dev);
- if (err) {
- free_dca_provider(dca);
- return NULL;
- }
-
- return dca;
-}
-
-
-static int ioat2_dca_add_requester(struct dca_provider *dca, struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
- u16 id;
- u16 global_req_table;
-
- /* This implementation only supports PCI-Express */
- if (dev->bus != &pci_bus_type)
- return -ENODEV;
- pdev = to_pci_dev(dev);
- id = dcaid_from_pcidev(pdev);
-
- if (ioatdca->requester_count == ioatdca->max_requesters)
- return -ENODEV;
-
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == NULL) {
- /* found an empty slot */
- ioatdca->requester_count++;
- ioatdca->req_slots[i].pdev = pdev;
- ioatdca->req_slots[i].rid = id;
- global_req_table =
- readw(ioatdca->dca_base + IOAT_DCA_GREQID_OFFSET);
- writel(id | IOAT_DCA_GREQID_VALID,
- ioatdca->iobase + global_req_table + (i * 4));
- return i;
- }
- }
- /* Error, ioatdma->requester_count is out of whack */
- return -EFAULT;
-}
-
-static int ioat2_dca_remove_requester(struct dca_provider *dca,
- struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
- u16 global_req_table;
-
- /* This implementation only supports PCI-Express */
- if (dev->bus != &pci_bus_type)
- return -ENODEV;
- pdev = to_pci_dev(dev);
-
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == pdev) {
- global_req_table =
- readw(ioatdca->dca_base + IOAT_DCA_GREQID_OFFSET);
- writel(0, ioatdca->iobase + global_req_table + (i * 4));
- ioatdca->req_slots[i].pdev = NULL;
- ioatdca->req_slots[i].rid = 0;
- ioatdca->requester_count--;
- return i;
- }
- }
- return -ENODEV;
-}
-
-static u8 ioat2_dca_get_tag(struct dca_provider *dca,
- struct device *dev,
- int cpu)
-{
- u8 tag;
-
- tag = ioat_dca_get_tag(dca, dev, cpu);
- tag = (~tag) & 0x1F;
- return tag;
-}
-
-static struct dca_ops ioat2_dca_ops = {
- .add_requester = ioat2_dca_add_requester,
- .remove_requester = ioat2_dca_remove_requester,
- .get_tag = ioat2_dca_get_tag,
- .dev_managed = ioat_dca_dev_managed,
-};
-
-static int ioat2_dca_count_dca_slots(void __iomem *iobase, u16 dca_offset)
-{
- int slots = 0;
- u32 req;
- u16 global_req_table;
-
- global_req_table = readw(iobase + dca_offset + IOAT_DCA_GREQID_OFFSET);
- if (global_req_table == 0)
- return 0;
- do {
- req = readl(iobase + global_req_table + (slots * sizeof(u32)));
- slots++;
- } while ((req & IOAT_DCA_GREQID_LASTID) == 0);
-
- return slots;
-}
-
-struct dca_provider *ioat2_dca_init(struct pci_dev *pdev, void __iomem *iobase)
-{
- struct dca_provider *dca;
- struct ioat_dca_priv *ioatdca;
- int slots;
- int i;
- int err;
- u32 tag_map;
- u16 dca_offset;
- u16 csi_fsb_control;
- u16 pcie_control;
- u8 bit;
-
- if (!system_has_dca_enabled(pdev))
- return NULL;
-
- dca_offset = readw(iobase + IOAT_DCAOFFSET_OFFSET);
- if (dca_offset == 0)
- return NULL;
-
- slots = ioat2_dca_count_dca_slots(iobase, dca_offset);
- if (slots == 0)
- return NULL;
-
- dca = alloc_dca_provider(&ioat2_dca_ops,
- sizeof(*ioatdca)
- + (sizeof(struct ioat_dca_slot) * slots));
- if (!dca)
- return NULL;
-
- ioatdca = dca_priv(dca);
- ioatdca->iobase = iobase;
- ioatdca->dca_base = iobase + dca_offset;
- ioatdca->max_requesters = slots;
-
- /* some bios might not know to turn these on */
- csi_fsb_control = readw(ioatdca->dca_base + IOAT_FSB_CAP_ENABLE_OFFSET);
- if ((csi_fsb_control & IOAT_FSB_CAP_ENABLE_PREFETCH) == 0) {
- csi_fsb_control |= IOAT_FSB_CAP_ENABLE_PREFETCH;
- writew(csi_fsb_control,
- ioatdca->dca_base + IOAT_FSB_CAP_ENABLE_OFFSET);
- }
- pcie_control = readw(ioatdca->dca_base + IOAT_PCI_CAP_ENABLE_OFFSET);
- if ((pcie_control & IOAT_PCI_CAP_ENABLE_MEMWR) == 0) {
- pcie_control |= IOAT_PCI_CAP_ENABLE_MEMWR;
- writew(pcie_control,
- ioatdca->dca_base + IOAT_PCI_CAP_ENABLE_OFFSET);
- }
-
-
- /* TODO version, compatibility and configuration checks */
-
- /* copy out the APIC to DCA tag map */
- tag_map = readl(ioatdca->dca_base + IOAT_APICID_TAG_MAP_OFFSET);
- for (i = 0; i < 5; i++) {
- bit = (tag_map >> (4 * i)) & 0x0f;
- if (bit < 8)
- ioatdca->tag_map[i] = bit | DCA_TAG_MAP_VALID;
- else
- ioatdca->tag_map[i] = 0;
- }
-
- if (!dca2_tag_map_valid(ioatdca->tag_map)) {
- dev_err(&pdev->dev, "APICID_TAG_MAP set incorrectly by BIOS, "
- "disabling DCA\n");
- free_dca_provider(dca);
- return NULL;
- }
-
- err = register_dca_provider(dca, &pdev->dev);
- if (err) {
- free_dca_provider(dca);
- return NULL;
- }
-
- return dca;
-}
-
-static int ioat3_dca_add_requester(struct dca_provider *dca, struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
- u16 id;
- u16 global_req_table;
-
- /* This implementation only supports PCI-Express */
- if (dev->bus != &pci_bus_type)
- return -ENODEV;
- pdev = to_pci_dev(dev);
- id = dcaid_from_pcidev(pdev);
-
- if (ioatdca->requester_count == ioatdca->max_requesters)
- return -ENODEV;
-
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == NULL) {
- /* found an empty slot */
- ioatdca->requester_count++;
- ioatdca->req_slots[i].pdev = pdev;
- ioatdca->req_slots[i].rid = id;
- global_req_table =
- readw(ioatdca->dca_base + IOAT3_DCA_GREQID_OFFSET);
- writel(id | IOAT_DCA_GREQID_VALID,
- ioatdca->iobase + global_req_table + (i * 4));
- return i;
- }
- }
- /* Error, ioatdma->requester_count is out of whack */
- return -EFAULT;
-}
-
-static int ioat3_dca_remove_requester(struct dca_provider *dca,
- struct device *dev)
-{
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- struct pci_dev *pdev;
- int i;
- u16 global_req_table;
-
- /* This implementation only supports PCI-Express */
- if (dev->bus != &pci_bus_type)
- return -ENODEV;
- pdev = to_pci_dev(dev);
-
- for (i = 0; i < ioatdca->max_requesters; i++) {
- if (ioatdca->req_slots[i].pdev == pdev) {
- global_req_table =
- readw(ioatdca->dca_base + IOAT3_DCA_GREQID_OFFSET);
- writel(0, ioatdca->iobase + global_req_table + (i * 4));
- ioatdca->req_slots[i].pdev = NULL;
- ioatdca->req_slots[i].rid = 0;
- ioatdca->requester_count--;
- return i;
- }
- }
- return -ENODEV;
-}
-
-static u8 ioat3_dca_get_tag(struct dca_provider *dca,
- struct device *dev,
- int cpu)
-{
- u8 tag;
-
- struct ioat_dca_priv *ioatdca = dca_priv(dca);
- int i, apic_id, bit, value;
- u8 entry;
-
- tag = 0;
- apic_id = cpu_physical_id(cpu);
-
- for (i = 0; i < IOAT_TAG_MAP_LEN; i++) {
- entry = ioatdca->tag_map[i];
- if (entry & DCA3_TAG_MAP_BIT_TO_SEL) {
- bit = entry &
- ~(DCA3_TAG_MAP_BIT_TO_SEL | DCA3_TAG_MAP_BIT_TO_INV);
- value = (apic_id & (1 << bit)) ? 1 : 0;
- } else if (entry & DCA3_TAG_MAP_BIT_TO_INV) {
- bit = entry & ~DCA3_TAG_MAP_BIT_TO_INV;
- value = (apic_id & (1 << bit)) ? 0 : 1;
- } else {
- value = (entry & DCA3_TAG_MAP_LITERAL_VAL) ? 1 : 0;
- }
- tag |= (value << i);
- }
-
- return tag;
-}
-
-static struct dca_ops ioat3_dca_ops = {
- .add_requester = ioat3_dca_add_requester,
- .remove_requester = ioat3_dca_remove_requester,
- .get_tag = ioat3_dca_get_tag,
- .dev_managed = ioat_dca_dev_managed,
-};
-
-static int ioat3_dca_count_dca_slots(void *iobase, u16 dca_offset)
-{
- int slots = 0;
- u32 req;
- u16 global_req_table;
-
- global_req_table = readw(iobase + dca_offset + IOAT3_DCA_GREQID_OFFSET);
- if (global_req_table == 0)
- return 0;
-
- do {
- req = readl(iobase + global_req_table + (slots * sizeof(u32)));
- slots++;
- } while ((req & IOAT_DCA_GREQID_LASTID) == 0);
-
- return slots;
-}
-
-struct dca_provider *ioat3_dca_init(struct pci_dev *pdev, void __iomem *iobase)
-{
- struct dca_provider *dca;
- struct ioat_dca_priv *ioatdca;
- int slots;
- int i;
- int err;
- u16 dca_offset;
- u16 csi_fsb_control;
- u16 pcie_control;
- u8 bit;
-
- union {
- u64 full;
- struct {
- u32 low;
- u32 high;
- };
- } tag_map;
-
- if (!system_has_dca_enabled(pdev))
- return NULL;
-
- dca_offset = readw(iobase + IOAT_DCAOFFSET_OFFSET);
- if (dca_offset == 0)
- return NULL;
-
- slots = ioat3_dca_count_dca_slots(iobase, dca_offset);
- if (slots == 0)
- return NULL;
-
- dca = alloc_dca_provider(&ioat3_dca_ops,
- sizeof(*ioatdca)
- + (sizeof(struct ioat_dca_slot) * slots));
- if (!dca)
- return NULL;
-
- ioatdca = dca_priv(dca);
- ioatdca->iobase = iobase;
- ioatdca->dca_base = iobase + dca_offset;
- ioatdca->max_requesters = slots;
-
- /* some bios might not know to turn these on */
- csi_fsb_control = readw(ioatdca->dca_base + IOAT3_CSI_CONTROL_OFFSET);
- if ((csi_fsb_control & IOAT3_CSI_CONTROL_PREFETCH) == 0) {
- csi_fsb_control |= IOAT3_CSI_CONTROL_PREFETCH;
- writew(csi_fsb_control,
- ioatdca->dca_base + IOAT3_CSI_CONTROL_OFFSET);
- }
- pcie_control = readw(ioatdca->dca_base + IOAT3_PCI_CONTROL_OFFSET);
- if ((pcie_control & IOAT3_PCI_CONTROL_MEMWR) == 0) {
- pcie_control |= IOAT3_PCI_CONTROL_MEMWR;
- writew(pcie_control,
- ioatdca->dca_base + IOAT3_PCI_CONTROL_OFFSET);
- }
-
-
- /* TODO version, compatibility and configuration checks */
-
- /* copy out the APIC to DCA tag map */
- tag_map.low =
- readl(ioatdca->dca_base + IOAT3_APICID_TAG_MAP_OFFSET_LOW);
- tag_map.high =
- readl(ioatdca->dca_base + IOAT3_APICID_TAG_MAP_OFFSET_HIGH);
- for (i = 0; i < 8; i++) {
- bit = tag_map.full >> (8 * i);
- ioatdca->tag_map[i] = bit & DCA_TAG_MAP_MASK;
- }
-
- err = register_dca_provider(dca, &pdev->dev);
- if (err) {
- free_dca_provider(dca);
- return NULL;
- }
-
- return dca;
-}
+++ /dev/null
-/*
- * Intel I/OAT DMA Linux driver
- * Copyright(c) 2004 - 2009 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms and conditions of the GNU General Public License,
- * version 2, as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
- *
- * The full GNU General Public License is included in this distribution in
- * the file called "COPYING".
- *
- */
-
-/*
- * This driver supports an Intel I/OAT DMA engine, which does asynchronous
- * copy operations.
- */
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/dmaengine.h>
-#include <linux/delay.h>
-#include <linux/dma-mapping.h>
-#include <linux/workqueue.h>
-#include <linux/i7300_idle.h>
-#include "ioatdma.h"
-#include "ioatdma_registers.h"
-#include "ioatdma_hw.h"
-
-#define to_ioat_chan(chan) container_of(chan, struct ioat_dma_chan, common)
-#define to_ioatdma_device(dev) container_of(dev, struct ioatdma_device, common)
-#define to_ioat_desc(lh) container_of(lh, struct ioat_desc_sw, node)
-#define tx_to_ioat_desc(tx) container_of(tx, struct ioat_desc_sw, async_tx)
-
-#define chan_num(ch) ((int)((ch)->reg_base - (ch)->device->reg_base) / 0x80)
-static int ioat_pending_level = 4;
-module_param(ioat_pending_level, int, 0644);
-MODULE_PARM_DESC(ioat_pending_level,
- "high-water mark for pushing ioat descriptors (default: 4)");
-
-#define RESET_DELAY msecs_to_jiffies(100)
-#define WATCHDOG_DELAY round_jiffies(msecs_to_jiffies(2000))
-static void ioat_dma_chan_reset_part2(struct work_struct *work);
-static void ioat_dma_chan_watchdog(struct work_struct *work);
-
-/*
- * workaround for IOAT ver.3.0 null descriptor issue
- * (channel returns error when size is 0)
- */
-#define NULL_DESC_BUFFER_SIZE 1
-
-/* internal functions */
-static void ioat_dma_start_null_desc(struct ioat_dma_chan *ioat_chan);
-static void ioat_dma_memcpy_cleanup(struct ioat_dma_chan *ioat_chan);
-
-static struct ioat_desc_sw *
-ioat1_dma_get_next_descriptor(struct ioat_dma_chan *ioat_chan);
-static struct ioat_desc_sw *
-ioat2_dma_get_next_descriptor(struct ioat_dma_chan *ioat_chan);
-
-static inline struct ioat_dma_chan *ioat_lookup_chan_by_index(
- struct ioatdma_device *device,
- int index)
-{
- return device->idx[index];
-}
-
-/**
- * ioat_dma_do_interrupt - handler used for single vector interrupt mode
- * @irq: interrupt id
- * @data: interrupt data
- */
-static irqreturn_t ioat_dma_do_interrupt(int irq, void *data)
-{
- struct ioatdma_device *instance = data;
- struct ioat_dma_chan *ioat_chan;
- unsigned long attnstatus;
- int bit;
- u8 intrctrl;
-
- intrctrl = readb(instance->reg_base + IOAT_INTRCTRL_OFFSET);
-
- if (!(intrctrl & IOAT_INTRCTRL_MASTER_INT_EN))
- return IRQ_NONE;
-
- if (!(intrctrl & IOAT_INTRCTRL_INT_STATUS)) {
- writeb(intrctrl, instance->reg_base + IOAT_INTRCTRL_OFFSET);
- return IRQ_NONE;
- }
-
- attnstatus = readl(instance->reg_base + IOAT_ATTNSTATUS_OFFSET);
- for_each_bit(bit, &attnstatus, BITS_PER_LONG) {
- ioat_chan = ioat_lookup_chan_by_index(instance, bit);
- tasklet_schedule(&ioat_chan->cleanup_task);
- }
-
- writeb(intrctrl, instance->reg_base + IOAT_INTRCTRL_OFFSET);
- return IRQ_HANDLED;
-}
-
-/**
- * ioat_dma_do_interrupt_msix - handler used for vector-per-channel interrupt mode
- * @irq: interrupt id
- * @data: interrupt data
- */
-static irqreturn_t ioat_dma_do_interrupt_msix(int irq, void *data)
-{
- struct ioat_dma_chan *ioat_chan = data;
-
- tasklet_schedule(&ioat_chan->cleanup_task);
-
- return IRQ_HANDLED;
-}
-
-static void ioat_dma_cleanup_tasklet(unsigned long data);
-
-/**
- * ioat_dma_enumerate_channels - find and initialize the device's channels
- * @device: the device to be enumerated
- */
-static int ioat_dma_enumerate_channels(struct ioatdma_device *device)
-{
- u8 xfercap_scale;
- u32 xfercap;
- int i;
- struct ioat_dma_chan *ioat_chan;
-
- /*
- * IOAT ver.3 workarounds
- */
- if (device->version == IOAT_VER_3_0) {
- u32 chan_err_mask;
- u16 dev_id;
- u32 dmauncerrsts;
-
- /*
- * Write CHANERRMSK_INT with 3E07h to mask out the errors
- * that can cause stability issues for IOAT ver.3
- */
- chan_err_mask = 0x3E07;
- pci_write_config_dword(device->pdev,
- IOAT_PCI_CHANERRMASK_INT_OFFSET,
- chan_err_mask);
-
- /*
- * Clear DMAUNCERRSTS Cfg-Reg Parity Error status bit
- * (workaround for spurious config parity error after restart)
- */
- pci_read_config_word(device->pdev,
- IOAT_PCI_DEVICE_ID_OFFSET,
- &dev_id);
- if (dev_id == PCI_DEVICE_ID_INTEL_IOAT_TBG0) {
- dmauncerrsts = 0x10;
- pci_write_config_dword(device->pdev,
- IOAT_PCI_DMAUNCERRSTS_OFFSET,
- dmauncerrsts);
- }
- }
-
- device->common.chancnt = readb(device->reg_base + IOAT_CHANCNT_OFFSET);
- xfercap_scale = readb(device->reg_base + IOAT_XFERCAP_OFFSET);
- xfercap = (xfercap_scale == 0 ? -1 : (1UL << xfercap_scale));
-
-#ifdef CONFIG_I7300_IDLE_IOAT_CHANNEL
- if (i7300_idle_platform_probe(NULL, NULL, 1) == 0) {
- device->common.chancnt--;
- }
-#endif
- for (i = 0; i < device->common.chancnt; i++) {
- ioat_chan = kzalloc(sizeof(*ioat_chan), GFP_KERNEL);
- if (!ioat_chan) {
- device->common.chancnt = i;
- break;
- }
-
- ioat_chan->device = device;
- ioat_chan->reg_base = device->reg_base + (0x80 * (i + 1));
- ioat_chan->xfercap = xfercap;
- ioat_chan->desccount = 0;
- INIT_DELAYED_WORK(&ioat_chan->work, ioat_dma_chan_reset_part2);
- if (ioat_chan->device->version == IOAT_VER_2_0)
- writel(IOAT_DCACTRL_CMPL_WRITE_ENABLE |
- IOAT_DMA_DCA_ANY_CPU,
- ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
- else if (ioat_chan->device->version == IOAT_VER_3_0)
- writel(IOAT_DMA_DCA_ANY_CPU,
- ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
- spin_lock_init(&ioat_chan->cleanup_lock);
- spin_lock_init(&ioat_chan->desc_lock);
- INIT_LIST_HEAD(&ioat_chan->free_desc);
- INIT_LIST_HEAD(&ioat_chan->used_desc);
- /* This should be made common somewhere in dmaengine.c */
- ioat_chan->common.device = &device->common;
- list_add_tail(&ioat_chan->common.device_node,
- &device->common.channels);
- device->idx[i] = ioat_chan;
- tasklet_init(&ioat_chan->cleanup_task,
- ioat_dma_cleanup_tasklet,
- (unsigned long) ioat_chan);
- tasklet_disable(&ioat_chan->cleanup_task);
- }
- return device->common.chancnt;
-}
-
-/**
- * ioat_dma_memcpy_issue_pending - push potentially unrecognized appended
- * descriptors to hw
- * @chan: DMA channel handle
- */
-static inline void __ioat1_dma_memcpy_issue_pending(
- struct ioat_dma_chan *ioat_chan)
-{
- ioat_chan->pending = 0;
- writeb(IOAT_CHANCMD_APPEND, ioat_chan->reg_base + IOAT1_CHANCMD_OFFSET);
-}
-
-static void ioat1_dma_memcpy_issue_pending(struct dma_chan *chan)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
-
- if (ioat_chan->pending > 0) {
- spin_lock_bh(&ioat_chan->desc_lock);
- __ioat1_dma_memcpy_issue_pending(ioat_chan);
- spin_unlock_bh(&ioat_chan->desc_lock);
- }
-}
-
-static inline void __ioat2_dma_memcpy_issue_pending(
- struct ioat_dma_chan *ioat_chan)
-{
- ioat_chan->pending = 0;
- writew(ioat_chan->dmacount,
- ioat_chan->reg_base + IOAT_CHAN_DMACOUNT_OFFSET);
-}
-
-static void ioat2_dma_memcpy_issue_pending(struct dma_chan *chan)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
-
- if (ioat_chan->pending > 0) {
- spin_lock_bh(&ioat_chan->desc_lock);
- __ioat2_dma_memcpy_issue_pending(ioat_chan);
- spin_unlock_bh(&ioat_chan->desc_lock);
- }
-}
-
-
-/**
- * ioat_dma_chan_reset_part2 - reinit the channel after a reset
- */
-static void ioat_dma_chan_reset_part2(struct work_struct *work)
-{
- struct ioat_dma_chan *ioat_chan =
- container_of(work, struct ioat_dma_chan, work.work);
- struct ioat_desc_sw *desc;
-
- spin_lock_bh(&ioat_chan->cleanup_lock);
- spin_lock_bh(&ioat_chan->desc_lock);
-
- ioat_chan->completion_virt->low = 0;
- ioat_chan->completion_virt->high = 0;
- ioat_chan->pending = 0;
-
- /*
- * count the descriptors waiting, and be sure to do it
- * right for both the CB1 line and the CB2 ring
- */
- ioat_chan->dmacount = 0;
- if (ioat_chan->used_desc.prev) {
- desc = to_ioat_desc(ioat_chan->used_desc.prev);
- do {
- ioat_chan->dmacount++;
- desc = to_ioat_desc(desc->node.next);
- } while (&desc->node != ioat_chan->used_desc.next);
- }
-
- /*
- * write the new starting descriptor address
- * this puts channel engine into ARMED state
- */
- desc = to_ioat_desc(ioat_chan->used_desc.prev);
- switch (ioat_chan->device->version) {
- case IOAT_VER_1_2:
- writel(((u64) desc->async_tx.phys) & 0x00000000FFFFFFFF,
- ioat_chan->reg_base + IOAT1_CHAINADDR_OFFSET_LOW);
- writel(((u64) desc->async_tx.phys) >> 32,
- ioat_chan->reg_base + IOAT1_CHAINADDR_OFFSET_HIGH);
-
- writeb(IOAT_CHANCMD_START, ioat_chan->reg_base
- + IOAT_CHANCMD_OFFSET(ioat_chan->device->version));
- break;
- case IOAT_VER_2_0:
- writel(((u64) desc->async_tx.phys) & 0x00000000FFFFFFFF,
- ioat_chan->reg_base + IOAT2_CHAINADDR_OFFSET_LOW);
- writel(((u64) desc->async_tx.phys) >> 32,
- ioat_chan->reg_base + IOAT2_CHAINADDR_OFFSET_HIGH);
-
- /* tell the engine to go with what's left to be done */
- writew(ioat_chan->dmacount,
- ioat_chan->reg_base + IOAT_CHAN_DMACOUNT_OFFSET);
-
- break;
- }
- dev_err(&ioat_chan->device->pdev->dev,
- "chan%d reset - %d descs waiting, %d total desc\n",
- chan_num(ioat_chan), ioat_chan->dmacount, ioat_chan->desccount);
-
- spin_unlock_bh(&ioat_chan->desc_lock);
- spin_unlock_bh(&ioat_chan->cleanup_lock);
-}
-
-/**
- * ioat_dma_reset_channel - restart a channel
- * @ioat_chan: IOAT DMA channel handle
- */
-static void ioat_dma_reset_channel(struct ioat_dma_chan *ioat_chan)
-{
- u32 chansts, chanerr;
-
- if (!ioat_chan->used_desc.prev)
- return;
-
- chanerr = readl(ioat_chan->reg_base + IOAT_CHANERR_OFFSET);
- chansts = (ioat_chan->completion_virt->low
- & IOAT_CHANSTS_DMA_TRANSFER_STATUS);
- if (chanerr) {
- dev_err(&ioat_chan->device->pdev->dev,
- "chan%d, CHANSTS = 0x%08x CHANERR = 0x%04x, clearing\n",
- chan_num(ioat_chan), chansts, chanerr);
- writel(chanerr, ioat_chan->reg_base + IOAT_CHANERR_OFFSET);
- }
-
- /*
- * whack it upside the head with a reset
- * and wait for things to settle out.
- * force the pending count to a really big negative
- * to make sure no one forces an issue_pending
- * while we're waiting.
- */
-
- spin_lock_bh(&ioat_chan->desc_lock);
- ioat_chan->pending = INT_MIN;
- writeb(IOAT_CHANCMD_RESET,
- ioat_chan->reg_base
- + IOAT_CHANCMD_OFFSET(ioat_chan->device->version));
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- /* schedule the 2nd half instead of sleeping a long time */
- schedule_delayed_work(&ioat_chan->work, RESET_DELAY);
-}
-
-/**
- * ioat_dma_chan_watchdog - watch for stuck channels
- */
-static void ioat_dma_chan_watchdog(struct work_struct *work)
-{
- struct ioatdma_device *device =
- container_of(work, struct ioatdma_device, work.work);
- struct ioat_dma_chan *ioat_chan;
- int i;
-
- union {
- u64 full;
- struct {
- u32 low;
- u32 high;
- };
- } completion_hw;
- unsigned long compl_desc_addr_hw;
-
- for (i = 0; i < device->common.chancnt; i++) {
- ioat_chan = ioat_lookup_chan_by_index(device, i);
-
- if (ioat_chan->device->version == IOAT_VER_1_2
- /* have we started processing anything yet */
- && ioat_chan->last_completion
- /* have we completed any since last watchdog cycle? */
- && (ioat_chan->last_completion ==
- ioat_chan->watchdog_completion)
- /* has TCP stuck on one cookie since last watchdog? */
- && (ioat_chan->watchdog_tcp_cookie ==
- ioat_chan->watchdog_last_tcp_cookie)
- && (ioat_chan->watchdog_tcp_cookie !=
- ioat_chan->completed_cookie)
- /* is there something in the chain to be processed? */
- /* CB1 chain always has at least the last one processed */
- && (ioat_chan->used_desc.prev != ioat_chan->used_desc.next)
- && ioat_chan->pending == 0) {
-
- /*
- * check CHANSTS register for completed
- * descriptor address.
- * if it is different than completion writeback,
- * it is not zero
- * and it has changed since the last watchdog
- * we can assume that channel
- * is still working correctly
- * and the problem is in completion writeback.
- * update completion writeback
- * with actual CHANSTS value
- * else
- * try resetting the channel
- */
-
- completion_hw.low = readl(ioat_chan->reg_base +
- IOAT_CHANSTS_OFFSET_LOW(ioat_chan->device->version));
- completion_hw.high = readl(ioat_chan->reg_base +
- IOAT_CHANSTS_OFFSET_HIGH(ioat_chan->device->version));
-#if (BITS_PER_LONG == 64)
- compl_desc_addr_hw =
- completion_hw.full
- & IOAT_CHANSTS_COMPLETED_DESCRIPTOR_ADDR;
-#else
- compl_desc_addr_hw =
- completion_hw.low & IOAT_LOW_COMPLETION_MASK;
-#endif
-
- if ((compl_desc_addr_hw != 0)
- && (compl_desc_addr_hw != ioat_chan->watchdog_completion)
- && (compl_desc_addr_hw != ioat_chan->last_compl_desc_addr_hw)) {
- ioat_chan->last_compl_desc_addr_hw = compl_desc_addr_hw;
- ioat_chan->completion_virt->low = completion_hw.low;
- ioat_chan->completion_virt->high = completion_hw.high;
- } else {
- ioat_dma_reset_channel(ioat_chan);
- ioat_chan->watchdog_completion = 0;
- ioat_chan->last_compl_desc_addr_hw = 0;
- }
-
- /*
- * for version 2.0 if there are descriptors yet to be processed
- * and the last completed hasn't changed since the last watchdog
- * if they haven't hit the pending level
- * issue the pending to push them through
- * else
- * try resetting the channel
- */
- } else if (ioat_chan->device->version == IOAT_VER_2_0
- && ioat_chan->used_desc.prev
- && ioat_chan->last_completion
- && ioat_chan->last_completion == ioat_chan->watchdog_completion) {
-
- if (ioat_chan->pending < ioat_pending_level)
- ioat2_dma_memcpy_issue_pending(&ioat_chan->common);
- else {
- ioat_dma_reset_channel(ioat_chan);
- ioat_chan->watchdog_completion = 0;
- }
- } else {
- ioat_chan->last_compl_desc_addr_hw = 0;
- ioat_chan->watchdog_completion
- = ioat_chan->last_completion;
- }
-
- ioat_chan->watchdog_last_tcp_cookie =
- ioat_chan->watchdog_tcp_cookie;
- }
-
- schedule_delayed_work(&device->work, WATCHDOG_DELAY);
-}
-
-static dma_cookie_t ioat1_tx_submit(struct dma_async_tx_descriptor *tx)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(tx->chan);
- struct ioat_desc_sw *first = tx_to_ioat_desc(tx);
- struct ioat_desc_sw *prev, *new;
- struct ioat_dma_descriptor *hw;
- dma_cookie_t cookie;
- LIST_HEAD(new_chain);
- u32 copy;
- size_t len;
- dma_addr_t src, dst;
- unsigned long orig_flags;
- unsigned int desc_count = 0;
-
- /* src and dest and len are stored in the initial descriptor */
- len = first->len;
- src = first->src;
- dst = first->dst;
- orig_flags = first->async_tx.flags;
- new = first;
-
- spin_lock_bh(&ioat_chan->desc_lock);
- prev = to_ioat_desc(ioat_chan->used_desc.prev);
- prefetch(prev->hw);
- do {
- copy = min_t(size_t, len, ioat_chan->xfercap);
-
- async_tx_ack(&new->async_tx);
-
- hw = new->hw;
- hw->size = copy;
- hw->ctl = 0;
- hw->src_addr = src;
- hw->dst_addr = dst;
- hw->next = 0;
-
- /* chain together the physical address list for the HW */
- wmb();
- prev->hw->next = (u64) new->async_tx.phys;
-
- len -= copy;
- dst += copy;
- src += copy;
-
- list_add_tail(&new->node, &new_chain);
- desc_count++;
- prev = new;
- } while (len && (new = ioat1_dma_get_next_descriptor(ioat_chan)));
-
- if (!new) {
- dev_err(&ioat_chan->device->pdev->dev,
- "tx submit failed\n");
- spin_unlock_bh(&ioat_chan->desc_lock);
- return -ENOMEM;
- }
-
- hw->ctl = IOAT_DMA_DESCRIPTOR_CTL_CP_STS;
- if (first->async_tx.callback) {
- hw->ctl |= IOAT_DMA_DESCRIPTOR_CTL_INT_GN;
- if (first != new) {
- /* move callback into to last desc */
- new->async_tx.callback = first->async_tx.callback;
- new->async_tx.callback_param
- = first->async_tx.callback_param;
- first->async_tx.callback = NULL;
- first->async_tx.callback_param = NULL;
- }
- }
-
- new->tx_cnt = desc_count;
- new->async_tx.flags = orig_flags; /* client is in control of this ack */
-
- /* store the original values for use in later cleanup */
- if (new != first) {
- new->src = first->src;
- new->dst = first->dst;
- new->len = first->len;
- }
-
- /* cookie incr and addition to used_list must be atomic */
- cookie = ioat_chan->common.cookie;
- cookie++;
- if (cookie < 0)
- cookie = 1;
- ioat_chan->common.cookie = new->async_tx.cookie = cookie;
-
- /* write address into NextDescriptor field of last desc in chain */
- to_ioat_desc(ioat_chan->used_desc.prev)->hw->next =
- first->async_tx.phys;
- list_splice_tail(&new_chain, &ioat_chan->used_desc);
-
- ioat_chan->dmacount += desc_count;
- ioat_chan->pending += desc_count;
- if (ioat_chan->pending >= ioat_pending_level)
- __ioat1_dma_memcpy_issue_pending(ioat_chan);
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- return cookie;
-}
-
-static dma_cookie_t ioat2_tx_submit(struct dma_async_tx_descriptor *tx)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(tx->chan);
- struct ioat_desc_sw *first = tx_to_ioat_desc(tx);
- struct ioat_desc_sw *new;
- struct ioat_dma_descriptor *hw;
- dma_cookie_t cookie;
- u32 copy;
- size_t len;
- dma_addr_t src, dst;
- unsigned long orig_flags;
- unsigned int desc_count = 0;
-
- /* src and dest and len are stored in the initial descriptor */
- len = first->len;
- src = first->src;
- dst = first->dst;
- orig_flags = first->async_tx.flags;
- new = first;
-
- /*
- * ioat_chan->desc_lock is still in force in version 2 path
- * it gets unlocked at end of this function
- */
- do {
- copy = min_t(size_t, len, ioat_chan->xfercap);
-
- async_tx_ack(&new->async_tx);
-
- hw = new->hw;
- hw->size = copy;
- hw->ctl = 0;
- hw->src_addr = src;
- hw->dst_addr = dst;
-
- len -= copy;
- dst += copy;
- src += copy;
- desc_count++;
- } while (len && (new = ioat2_dma_get_next_descriptor(ioat_chan)));
-
- if (!new) {
- dev_err(&ioat_chan->device->pdev->dev,
- "tx submit failed\n");
- spin_unlock_bh(&ioat_chan->desc_lock);
- return -ENOMEM;
- }
-
- hw->ctl |= IOAT_DMA_DESCRIPTOR_CTL_CP_STS;
- if (first->async_tx.callback) {
- hw->ctl |= IOAT_DMA_DESCRIPTOR_CTL_INT_GN;
- if (first != new) {
- /* move callback into to last desc */
- new->async_tx.callback = first->async_tx.callback;
- new->async_tx.callback_param
- = first->async_tx.callback_param;
- first->async_tx.callback = NULL;
- first->async_tx.callback_param = NULL;
- }
- }
-
- new->tx_cnt = desc_count;
- new->async_tx.flags = orig_flags; /* client is in control of this ack */
-
- /* store the original values for use in later cleanup */
- if (new != first) {
- new->src = first->src;
- new->dst = first->dst;
- new->len = first->len;
- }
-
- /* cookie incr and addition to used_list must be atomic */
- cookie = ioat_chan->common.cookie;
- cookie++;
- if (cookie < 0)
- cookie = 1;
- ioat_chan->common.cookie = new->async_tx.cookie = cookie;
-
- ioat_chan->dmacount += desc_count;
- ioat_chan->pending += desc_count;
- if (ioat_chan->pending >= ioat_pending_level)
- __ioat2_dma_memcpy_issue_pending(ioat_chan);
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- return cookie;
-}
-
-/**
- * ioat_dma_alloc_descriptor - allocate and return a sw and hw descriptor pair
- * @ioat_chan: the channel supplying the memory pool for the descriptors
- * @flags: allocation flags
- */
-static struct ioat_desc_sw *ioat_dma_alloc_descriptor(
- struct ioat_dma_chan *ioat_chan,
- gfp_t flags)
-{
- struct ioat_dma_descriptor *desc;
- struct ioat_desc_sw *desc_sw;
- struct ioatdma_device *ioatdma_device;
- dma_addr_t phys;
-
- ioatdma_device = to_ioatdma_device(ioat_chan->common.device);
- desc = pci_pool_alloc(ioatdma_device->dma_pool, flags, &phys);
- if (unlikely(!desc))
- return NULL;
-
- desc_sw = kzalloc(sizeof(*desc_sw), flags);
- if (unlikely(!desc_sw)) {
- pci_pool_free(ioatdma_device->dma_pool, desc, phys);
- return NULL;
- }
-
- memset(desc, 0, sizeof(*desc));
- dma_async_tx_descriptor_init(&desc_sw->async_tx, &ioat_chan->common);
- switch (ioat_chan->device->version) {
- case IOAT_VER_1_2:
- desc_sw->async_tx.tx_submit = ioat1_tx_submit;
- break;
- case IOAT_VER_2_0:
- case IOAT_VER_3_0:
- desc_sw->async_tx.tx_submit = ioat2_tx_submit;
- break;
- }
-
- desc_sw->hw = desc;
- desc_sw->async_tx.phys = phys;
-
- return desc_sw;
-}
-
-static int ioat_initial_desc_count = 256;
-module_param(ioat_initial_desc_count, int, 0644);
-MODULE_PARM_DESC(ioat_initial_desc_count,
- "initial descriptors per channel (default: 256)");
-
-/**
- * ioat2_dma_massage_chan_desc - link the descriptors into a circle
- * @ioat_chan: the channel to be massaged
- */
-static void ioat2_dma_massage_chan_desc(struct ioat_dma_chan *ioat_chan)
-{
- struct ioat_desc_sw *desc, *_desc;
-
- /* setup used_desc */
- ioat_chan->used_desc.next = ioat_chan->free_desc.next;
- ioat_chan->used_desc.prev = NULL;
-
- /* pull free_desc out of the circle so that every node is a hw
- * descriptor, but leave it pointing to the list
- */
- ioat_chan->free_desc.prev->next = ioat_chan->free_desc.next;
- ioat_chan->free_desc.next->prev = ioat_chan->free_desc.prev;
-
- /* circle link the hw descriptors */
- desc = to_ioat_desc(ioat_chan->free_desc.next);
- desc->hw->next = to_ioat_desc(desc->node.next)->async_tx.phys;
- list_for_each_entry_safe(desc, _desc, ioat_chan->free_desc.next, node) {
- desc->hw->next = to_ioat_desc(desc->node.next)->async_tx.phys;
- }
-}
-
-/**
- * ioat_dma_alloc_chan_resources - returns the number of allocated descriptors
- * @chan: the channel to be filled out
- */
-static int ioat_dma_alloc_chan_resources(struct dma_chan *chan)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
- struct ioat_desc_sw *desc;
- u16 chanctrl;
- u32 chanerr;
- int i;
- LIST_HEAD(tmp_list);
-
- /* have we already been set up? */
- if (!list_empty(&ioat_chan->free_desc))
- return ioat_chan->desccount;
-
- /* Setup register to interrupt and write completion status on error */
- chanctrl = IOAT_CHANCTRL_ERR_INT_EN |
- IOAT_CHANCTRL_ANY_ERR_ABORT_EN |
- IOAT_CHANCTRL_ERR_COMPLETION_EN;
- writew(chanctrl, ioat_chan->reg_base + IOAT_CHANCTRL_OFFSET);
-
- chanerr = readl(ioat_chan->reg_base + IOAT_CHANERR_OFFSET);
- if (chanerr) {
- dev_err(&ioat_chan->device->pdev->dev,
- "CHANERR = %x, clearing\n", chanerr);
- writel(chanerr, ioat_chan->reg_base + IOAT_CHANERR_OFFSET);
- }
-
- /* Allocate descriptors */
- for (i = 0; i < ioat_initial_desc_count; i++) {
- desc = ioat_dma_alloc_descriptor(ioat_chan, GFP_KERNEL);
- if (!desc) {
- dev_err(&ioat_chan->device->pdev->dev,
- "Only %d initial descriptors\n", i);
- break;
- }
- list_add_tail(&desc->node, &tmp_list);
- }
- spin_lock_bh(&ioat_chan->desc_lock);
- ioat_chan->desccount = i;
- list_splice(&tmp_list, &ioat_chan->free_desc);
- if (ioat_chan->device->version != IOAT_VER_1_2)
- ioat2_dma_massage_chan_desc(ioat_chan);
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- /* allocate a completion writeback area */
- /* doing 2 32bit writes to mmio since 1 64b write doesn't work */
- ioat_chan->completion_virt =
- pci_pool_alloc(ioat_chan->device->completion_pool,
- GFP_KERNEL,
- &ioat_chan->completion_addr);
- memset(ioat_chan->completion_virt, 0,
- sizeof(*ioat_chan->completion_virt));
- writel(((u64) ioat_chan->completion_addr) & 0x00000000FFFFFFFF,
- ioat_chan->reg_base + IOAT_CHANCMP_OFFSET_LOW);
- writel(((u64) ioat_chan->completion_addr) >> 32,
- ioat_chan->reg_base + IOAT_CHANCMP_OFFSET_HIGH);
-
- tasklet_enable(&ioat_chan->cleanup_task);
- ioat_dma_start_null_desc(ioat_chan); /* give chain to dma device */
- return ioat_chan->desccount;
-}
-
-/**
- * ioat_dma_free_chan_resources - release all the descriptors
- * @chan: the channel to be cleaned
- */
-static void ioat_dma_free_chan_resources(struct dma_chan *chan)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
- struct ioatdma_device *ioatdma_device = to_ioatdma_device(chan->device);
- struct ioat_desc_sw *desc, *_desc;
- int in_use_descs = 0;
-
- /* Before freeing channel resources first check
- * if they have been previously allocated for this channel.
- */
- if (ioat_chan->desccount == 0)
- return;
-
- tasklet_disable(&ioat_chan->cleanup_task);
- ioat_dma_memcpy_cleanup(ioat_chan);
-
- /* Delay 100ms after reset to allow internal DMA logic to quiesce
- * before removing DMA descriptor resources.
- */
- writeb(IOAT_CHANCMD_RESET,
- ioat_chan->reg_base
- + IOAT_CHANCMD_OFFSET(ioat_chan->device->version));
- mdelay(100);
-
- spin_lock_bh(&ioat_chan->desc_lock);
- switch (ioat_chan->device->version) {
- case IOAT_VER_1_2:
- list_for_each_entry_safe(desc, _desc,
- &ioat_chan->used_desc, node) {
- in_use_descs++;
- list_del(&desc->node);
- pci_pool_free(ioatdma_device->dma_pool, desc->hw,
- desc->async_tx.phys);
- kfree(desc);
- }
- list_for_each_entry_safe(desc, _desc,
- &ioat_chan->free_desc, node) {
- list_del(&desc->node);
- pci_pool_free(ioatdma_device->dma_pool, desc->hw,
- desc->async_tx.phys);
- kfree(desc);
- }
- break;
- case IOAT_VER_2_0:
- case IOAT_VER_3_0:
- list_for_each_entry_safe(desc, _desc,
- ioat_chan->free_desc.next, node) {
- list_del(&desc->node);
- pci_pool_free(ioatdma_device->dma_pool, desc->hw,
- desc->async_tx.phys);
- kfree(desc);
- }
- desc = to_ioat_desc(ioat_chan->free_desc.next);
- pci_pool_free(ioatdma_device->dma_pool, desc->hw,
- desc->async_tx.phys);
- kfree(desc);
- INIT_LIST_HEAD(&ioat_chan->free_desc);
- INIT_LIST_HEAD(&ioat_chan->used_desc);
- break;
- }
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- pci_pool_free(ioatdma_device->completion_pool,
- ioat_chan->completion_virt,
- ioat_chan->completion_addr);
-
- /* one is ok since we left it on there on purpose */
- if (in_use_descs > 1)
- dev_err(&ioat_chan->device->pdev->dev,
- "Freeing %d in use descriptors!\n",
- in_use_descs - 1);
-
- ioat_chan->last_completion = ioat_chan->completion_addr = 0;
- ioat_chan->pending = 0;
- ioat_chan->dmacount = 0;
- ioat_chan->desccount = 0;
- ioat_chan->watchdog_completion = 0;
- ioat_chan->last_compl_desc_addr_hw = 0;
- ioat_chan->watchdog_tcp_cookie =
- ioat_chan->watchdog_last_tcp_cookie = 0;
-}
-
-/**
- * ioat_dma_get_next_descriptor - return the next available descriptor
- * @ioat_chan: IOAT DMA channel handle
- *
- * Gets the next descriptor from the chain, and must be called with the
- * channel's desc_lock held. Allocates more descriptors if the channel
- * has run out.
- */
-static struct ioat_desc_sw *
-ioat1_dma_get_next_descriptor(struct ioat_dma_chan *ioat_chan)
-{
- struct ioat_desc_sw *new;
-
- if (!list_empty(&ioat_chan->free_desc)) {
- new = to_ioat_desc(ioat_chan->free_desc.next);
- list_del(&new->node);
- } else {
- /* try to get another desc */
- new = ioat_dma_alloc_descriptor(ioat_chan, GFP_ATOMIC);
- if (!new) {
- dev_err(&ioat_chan->device->pdev->dev,
- "alloc failed\n");
- return NULL;
- }
- }
-
- prefetch(new->hw);
- return new;
-}
-
-static struct ioat_desc_sw *
-ioat2_dma_get_next_descriptor(struct ioat_dma_chan *ioat_chan)
-{
- struct ioat_desc_sw *new;
-
- /*
- * used.prev points to where to start processing
- * used.next points to next free descriptor
- * if used.prev == NULL, there are none waiting to be processed
- * if used.next == used.prev.prev, there is only one free descriptor,
- * and we need to use it to as a noop descriptor before
- * linking in a new set of descriptors, since the device
- * has probably already read the pointer to it
- */
- if (ioat_chan->used_desc.prev &&
- ioat_chan->used_desc.next == ioat_chan->used_desc.prev->prev) {
-
- struct ioat_desc_sw *desc;
- struct ioat_desc_sw *noop_desc;
- int i;
-
- /* set up the noop descriptor */
- noop_desc = to_ioat_desc(ioat_chan->used_desc.next);
- /* set size to non-zero value (channel returns error when size is 0) */
- noop_desc->hw->size = NULL_DESC_BUFFER_SIZE;
- noop_desc->hw->ctl = IOAT_DMA_DESCRIPTOR_NUL;
- noop_desc->hw->src_addr = 0;
- noop_desc->hw->dst_addr = 0;
-
- ioat_chan->used_desc.next = ioat_chan->used_desc.next->next;
- ioat_chan->pending++;
- ioat_chan->dmacount++;
-
- /* try to get a few more descriptors */
- for (i = 16; i; i--) {
- desc = ioat_dma_alloc_descriptor(ioat_chan, GFP_ATOMIC);
- if (!desc) {
- dev_err(&ioat_chan->device->pdev->dev,
- "alloc failed\n");
- break;
- }
- list_add_tail(&desc->node, ioat_chan->used_desc.next);
-
- desc->hw->next
- = to_ioat_desc(desc->node.next)->async_tx.phys;
- to_ioat_desc(desc->node.prev)->hw->next
- = desc->async_tx.phys;
- ioat_chan->desccount++;
- }
-
- ioat_chan->used_desc.next = noop_desc->node.next;
- }
- new = to_ioat_desc(ioat_chan->used_desc.next);
- prefetch(new);
- ioat_chan->used_desc.next = new->node.next;
-
- if (ioat_chan->used_desc.prev == NULL)
- ioat_chan->used_desc.prev = &new->node;
-
- prefetch(new->hw);
- return new;
-}
-
-static struct ioat_desc_sw *ioat_dma_get_next_descriptor(
- struct ioat_dma_chan *ioat_chan)
-{
- if (!ioat_chan)
- return NULL;
-
- switch (ioat_chan->device->version) {
- case IOAT_VER_1_2:
- return ioat1_dma_get_next_descriptor(ioat_chan);
- case IOAT_VER_2_0:
- case IOAT_VER_3_0:
- return ioat2_dma_get_next_descriptor(ioat_chan);
- }
- return NULL;
-}
-
-static struct dma_async_tx_descriptor *ioat1_dma_prep_memcpy(
- struct dma_chan *chan,
- dma_addr_t dma_dest,
- dma_addr_t dma_src,
- size_t len,
- unsigned long flags)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
- struct ioat_desc_sw *new;
-
- spin_lock_bh(&ioat_chan->desc_lock);
- new = ioat_dma_get_next_descriptor(ioat_chan);
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- if (new) {
- new->len = len;
- new->dst = dma_dest;
- new->src = dma_src;
- new->async_tx.flags = flags;
- return &new->async_tx;
- } else {
- dev_err(&ioat_chan->device->pdev->dev,
- "chan%d - get_next_desc failed: %d descs waiting, %d total desc\n",
- chan_num(ioat_chan), ioat_chan->dmacount, ioat_chan->desccount);
- return NULL;
- }
-}
-
-static struct dma_async_tx_descriptor *ioat2_dma_prep_memcpy(
- struct dma_chan *chan,
- dma_addr_t dma_dest,
- dma_addr_t dma_src,
- size_t len,
- unsigned long flags)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
- struct ioat_desc_sw *new;
-
- spin_lock_bh(&ioat_chan->desc_lock);
- new = ioat2_dma_get_next_descriptor(ioat_chan);
-
- /*
- * leave ioat_chan->desc_lock set in ioat 2 path
- * it will get unlocked at end of tx_submit
- */
-
- if (new) {
- new->len = len;
- new->dst = dma_dest;
- new->src = dma_src;
- new->async_tx.flags = flags;
- return &new->async_tx;
- } else {
- spin_unlock_bh(&ioat_chan->desc_lock);
- dev_err(&ioat_chan->device->pdev->dev,
- "chan%d - get_next_desc failed: %d descs waiting, %d total desc\n",
- chan_num(ioat_chan), ioat_chan->dmacount, ioat_chan->desccount);
- return NULL;
- }
-}
-
-static void ioat_dma_cleanup_tasklet(unsigned long data)
-{
- struct ioat_dma_chan *chan = (void *)data;
- ioat_dma_memcpy_cleanup(chan);
- writew(IOAT_CHANCTRL_INT_DISABLE,
- chan->reg_base + IOAT_CHANCTRL_OFFSET);
-}
-
-static void
-ioat_dma_unmap(struct ioat_dma_chan *ioat_chan, struct ioat_desc_sw *desc)
-{
- if (!(desc->async_tx.flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
- if (desc->async_tx.flags & DMA_COMPL_DEST_UNMAP_SINGLE)
- pci_unmap_single(ioat_chan->device->pdev,
- pci_unmap_addr(desc, dst),
- pci_unmap_len(desc, len),
- PCI_DMA_FROMDEVICE);
- else
- pci_unmap_page(ioat_chan->device->pdev,
- pci_unmap_addr(desc, dst),
- pci_unmap_len(desc, len),
- PCI_DMA_FROMDEVICE);
- }
-
- if (!(desc->async_tx.flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
- if (desc->async_tx.flags & DMA_COMPL_SRC_UNMAP_SINGLE)
- pci_unmap_single(ioat_chan->device->pdev,
- pci_unmap_addr(desc, src),
- pci_unmap_len(desc, len),
- PCI_DMA_TODEVICE);
- else
- pci_unmap_page(ioat_chan->device->pdev,
- pci_unmap_addr(desc, src),
- pci_unmap_len(desc, len),
- PCI_DMA_TODEVICE);
- }
-}
-
-/**
- * ioat_dma_memcpy_cleanup - cleanup up finished descriptors
- * @chan: ioat channel to be cleaned up
- */
-static void ioat_dma_memcpy_cleanup(struct ioat_dma_chan *ioat_chan)
-{
- unsigned long phys_complete;
- struct ioat_desc_sw *desc, *_desc;
- dma_cookie_t cookie = 0;
- unsigned long desc_phys;
- struct ioat_desc_sw *latest_desc;
-
- prefetch(ioat_chan->completion_virt);
-
- if (!spin_trylock_bh(&ioat_chan->cleanup_lock))
- return;
-
- /* The completion writeback can happen at any time,
- so reads by the driver need to be atomic operations
- The descriptor physical addresses are limited to 32-bits
- when the CPU can only do a 32-bit mov */
-
-#if (BITS_PER_LONG == 64)
- phys_complete =
- ioat_chan->completion_virt->full
- & IOAT_CHANSTS_COMPLETED_DESCRIPTOR_ADDR;
-#else
- phys_complete =
- ioat_chan->completion_virt->low & IOAT_LOW_COMPLETION_MASK;
-#endif
-
- if ((ioat_chan->completion_virt->full
- & IOAT_CHANSTS_DMA_TRANSFER_STATUS) ==
- IOAT_CHANSTS_DMA_TRANSFER_STATUS_HALTED) {
- dev_err(&ioat_chan->device->pdev->dev,
- "Channel halted, chanerr = %x\n",
- readl(ioat_chan->reg_base + IOAT_CHANERR_OFFSET));
-
- /* TODO do something to salvage the situation */
- }
-
- if (phys_complete == ioat_chan->last_completion) {
- spin_unlock_bh(&ioat_chan->cleanup_lock);
- /*
- * perhaps we're stuck so hard that the watchdog can't go off?
- * try to catch it after 2 seconds
- */
- if (ioat_chan->device->version != IOAT_VER_3_0) {
- if (time_after(jiffies,
- ioat_chan->last_completion_time + HZ*WATCHDOG_DELAY)) {
- ioat_dma_chan_watchdog(&(ioat_chan->device->work.work));
- ioat_chan->last_completion_time = jiffies;
- }
- }
- return;
- }
- ioat_chan->last_completion_time = jiffies;
-
- cookie = 0;
- if (!spin_trylock_bh(&ioat_chan->desc_lock)) {
- spin_unlock_bh(&ioat_chan->cleanup_lock);
- return;
- }
-
- switch (ioat_chan->device->version) {
- case IOAT_VER_1_2:
- list_for_each_entry_safe(desc, _desc,
- &ioat_chan->used_desc, node) {
-
- /*
- * Incoming DMA requests may use multiple descriptors,
- * due to exceeding xfercap, perhaps. If so, only the
- * last one will have a cookie, and require unmapping.
- */
- if (desc->async_tx.cookie) {
- cookie = desc->async_tx.cookie;
- ioat_dma_unmap(ioat_chan, desc);
- if (desc->async_tx.callback) {
- desc->async_tx.callback(desc->async_tx.callback_param);
- desc->async_tx.callback = NULL;
- }
- }
-
- if (desc->async_tx.phys != phys_complete) {
- /*
- * a completed entry, but not the last, so clean
- * up if the client is done with the descriptor
- */
- if (async_tx_test_ack(&desc->async_tx)) {
- list_move_tail(&desc->node,
- &ioat_chan->free_desc);
- } else
- desc->async_tx.cookie = 0;
- } else {
- /*
- * last used desc. Do not remove, so we can
- * append from it, but don't look at it next
- * time, either
- */
- desc->async_tx.cookie = 0;
-
- /* TODO check status bits? */
- break;
- }
- }
- break;
- case IOAT_VER_2_0:
- case IOAT_VER_3_0:
- /* has some other thread has already cleaned up? */
- if (ioat_chan->used_desc.prev == NULL)
- break;
-
- /* work backwards to find latest finished desc */
- desc = to_ioat_desc(ioat_chan->used_desc.next);
- latest_desc = NULL;
- do {
- desc = to_ioat_desc(desc->node.prev);
- desc_phys = (unsigned long)desc->async_tx.phys
- & IOAT_CHANSTS_COMPLETED_DESCRIPTOR_ADDR;
- if (desc_phys == phys_complete) {
- latest_desc = desc;
- break;
- }
- } while (&desc->node != ioat_chan->used_desc.prev);
-
- if (latest_desc != NULL) {
-
- /* work forwards to clear finished descriptors */
- for (desc = to_ioat_desc(ioat_chan->used_desc.prev);
- &desc->node != latest_desc->node.next &&
- &desc->node != ioat_chan->used_desc.next;
- desc = to_ioat_desc(desc->node.next)) {
- if (desc->async_tx.cookie) {
- cookie = desc->async_tx.cookie;
- desc->async_tx.cookie = 0;
- ioat_dma_unmap(ioat_chan, desc);
- if (desc->async_tx.callback) {
- desc->async_tx.callback(desc->async_tx.callback_param);
- desc->async_tx.callback = NULL;
- }
- }
- }
-
- /* move used.prev up beyond those that are finished */
- if (&desc->node == ioat_chan->used_desc.next)
- ioat_chan->used_desc.prev = NULL;
- else
- ioat_chan->used_desc.prev = &desc->node;
- }
- break;
- }
-
- spin_unlock_bh(&ioat_chan->desc_lock);
-
- ioat_chan->last_completion = phys_complete;
- if (cookie != 0)
- ioat_chan->completed_cookie = cookie;
-
- spin_unlock_bh(&ioat_chan->cleanup_lock);
-}
-
-/**
- * ioat_dma_is_complete - poll the status of a IOAT DMA transaction
- * @chan: IOAT DMA channel handle
- * @cookie: DMA transaction identifier
- * @done: if not %NULL, updated with last completed transaction
- * @used: if not %NULL, updated with last used transaction
- */
-static enum dma_status ioat_dma_is_complete(struct dma_chan *chan,
- dma_cookie_t cookie,
- dma_cookie_t *done,
- dma_cookie_t *used)
-{
- struct ioat_dma_chan *ioat_chan = to_ioat_chan(chan);
- dma_cookie_t last_used;
- dma_cookie_t last_complete;
- enum dma_status ret;
-
- last_used = chan->cookie;
- last_complete = ioat_chan->completed_cookie;
- ioat_chan->watchdog_tcp_cookie = cookie;
-
- if (done)
- *done = last_complete;
- if (used)
- *used = last_used;
-
- ret = dma_async_is_complete(cookie, last_complete, last_used);
- if (ret == DMA_SUCCESS)
- return ret;
-
- ioat_dma_memcpy_cleanup(ioat_chan);
-
- last_used = chan->cookie;
- last_complete = ioat_chan->completed_cookie;
-
- if (done)
- *done = last_complete;
- if (used)
- *used = last_used;
-
- return dma_async_is_complete(cookie, last_complete, last_used);
-}
-
-static void ioat_dma_start_null_desc(struct ioat_dma_chan *ioat_chan)
-{
- struct ioat_desc_sw *desc;
-
- spin_lock_bh(&ioat_chan->desc_lock);
-
- desc = ioat_dma_get_next_descriptor(ioat_chan);
-
- if (!desc) {
- dev_err(&ioat_chan->device->pdev->dev,
- "Unable to start null desc - get next desc failed\n");
- spin_unlock_bh(&ioat_chan->desc_lock);
- return;
- }
-
- desc->hw->ctl = IOAT_DMA_DESCRIPTOR_NUL
- | IOAT_DMA_DESCRIPTOR_CTL_INT_GN
- | IOAT_DMA_DESCRIPTOR_CTL_CP_STS;
- /* set size to non-zero value (channel returns error when size is 0) */
- desc->hw->size = NULL_DESC_BUFFER_SIZE;
- desc->hw->src_addr = 0;
- desc->hw->dst_addr = 0;
- async_tx_ack(&desc->async_tx);
- switch (ioat_chan->device->version) {
- case IOAT_VER_1_2:
- desc->hw->next = 0;
- list_add_tail(&desc->node, &ioat_chan->used_desc);
-
- writel(((u64) desc->async_tx.phys) & 0x00000000FFFFFFFF,
- ioat_chan->reg_base + IOAT1_CHAINADDR_OFFSET_LOW);
- writel(((u64) desc->async_tx.phys) >> 32,
- ioat_chan->reg_base + IOAT1_CHAINADDR_OFFSET_HIGH);
-
- writeb(IOAT_CHANCMD_START, ioat_chan->reg_base
- + IOAT_CHANCMD_OFFSET(ioat_chan->device->version));
- break;
- case IOAT_VER_2_0:
- case IOAT_VER_3_0:
- writel(((u64) desc->async_tx.phys) & 0x00000000FFFFFFFF,
- ioat_chan->reg_base + IOAT2_CHAINADDR_OFFSET_LOW);
- writel(((u64) desc->async_tx.phys) >> 32,
- ioat_chan->reg_base + IOAT2_CHAINADDR_OFFSET_HIGH);
-
- ioat_chan->dmacount++;
- __ioat2_dma_memcpy_issue_pending(ioat_chan);
- break;
- }
- spin_unlock_bh(&ioat_chan->desc_lock);
-}
-
-/*
- * Perform a IOAT transaction to verify the HW works.
- */
-#define IOAT_TEST_SIZE 2000
-
-static void ioat_dma_test_callback(void *dma_async_param)
-{
- struct completion *cmp = dma_async_param;
-
- complete(cmp);
-}
-
-/**
- * ioat_dma_self_test - Perform a IOAT transaction to verify the HW works.
- * @device: device to be tested
- */
-static int ioat_dma_self_test(struct ioatdma_device *device)
-{
- int i;
- u8 *src;
- u8 *dest;
- struct dma_chan *dma_chan;
- struct dma_async_tx_descriptor *tx;
- dma_addr_t dma_dest, dma_src;
- dma_cookie_t cookie;
- int err = 0;
- struct completion cmp;
- unsigned long tmo;
- unsigned long flags;
-
- src = kzalloc(sizeof(u8) * IOAT_TEST_SIZE, GFP_KERNEL);
- if (!src)
- return -ENOMEM;
- dest = kzalloc(sizeof(u8) * IOAT_TEST_SIZE, GFP_KERNEL);
- if (!dest) {
- kfree(src);
- return -ENOMEM;
- }
-
- /* Fill in src buffer */
- for (i = 0; i < IOAT_TEST_SIZE; i++)
- src[i] = (u8)i;
-
- /* Start copy, using first DMA channel */
- dma_chan = container_of(device->common.channels.next,
- struct dma_chan,
- device_node);
- if (device->common.device_alloc_chan_resources(dma_chan) < 1) {
- dev_err(&device->pdev->dev,
- "selftest cannot allocate chan resource\n");
- err = -ENODEV;
- goto out;
- }
-
- dma_src = dma_map_single(dma_chan->device->dev, src, IOAT_TEST_SIZE,
- DMA_TO_DEVICE);
- dma_dest = dma_map_single(dma_chan->device->dev, dest, IOAT_TEST_SIZE,
- DMA_FROM_DEVICE);
- flags = DMA_COMPL_SRC_UNMAP_SINGLE | DMA_COMPL_DEST_UNMAP_SINGLE;
- tx = device->common.device_prep_dma_memcpy(dma_chan, dma_dest, dma_src,
- IOAT_TEST_SIZE, flags);
- if (!tx) {
- dev_err(&device->pdev->dev,
- "Self-test prep failed, disabling\n");
- err = -ENODEV;
- goto free_resources;
- }
-
- async_tx_ack(tx);
- init_completion(&cmp);
- tx->callback = ioat_dma_test_callback;
- tx->callback_param = &cmp;
- cookie = tx->tx_submit(tx);
- if (cookie < 0) {
- dev_err(&device->pdev->dev,
- "Self-test setup failed, disabling\n");
- err = -ENODEV;
- goto free_resources;
- }
- device->common.device_issue_pending(dma_chan);
-
- tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
-
- if (tmo == 0 ||
- device->common.device_is_tx_complete(dma_chan, cookie, NULL, NULL)
- != DMA_SUCCESS) {
- dev_err(&device->pdev->dev,
- "Self-test copy timed out, disabling\n");
- err = -ENODEV;
- goto free_resources;
- }
- if (memcmp(src, dest, IOAT_TEST_SIZE)) {
- dev_err(&device->pdev->dev,
- "Self-test copy failed compare, disabling\n");
- err = -ENODEV;
- goto free_resources;
- }
-
-free_resources:
- device->common.device_free_chan_resources(dma_chan);
-out:
- kfree(src);
- kfree(dest);
- return err;
-}
-
-static char ioat_interrupt_style[32] = "msix";
-module_param_string(ioat_interrupt_style, ioat_interrupt_style,
- sizeof(ioat_interrupt_style), 0644);
-MODULE_PARM_DESC(ioat_interrupt_style,
- "set ioat interrupt style: msix (default), "
- "msix-single-vector, msi, intx)");
-
-/**
- * ioat_dma_setup_interrupts - setup interrupt handler
- * @device: ioat device
- */
-static int ioat_dma_setup_interrupts(struct ioatdma_device *device)
-{
- struct ioat_dma_chan *ioat_chan;
- int err, i, j, msixcnt;
- u8 intrctrl = 0;
-
- if (!strcmp(ioat_interrupt_style, "msix"))
- goto msix;
- if (!strcmp(ioat_interrupt_style, "msix-single-vector"))
- goto msix_single_vector;
- if (!strcmp(ioat_interrupt_style, "msi"))
- goto msi;
- if (!strcmp(ioat_interrupt_style, "intx"))
- goto intx;
- dev_err(&device->pdev->dev, "invalid ioat_interrupt_style %s\n",
- ioat_interrupt_style);
- goto err_no_irq;
-
-msix:
- /* The number of MSI-X vectors should equal the number of channels */
- msixcnt = device->common.chancnt;
- for (i = 0; i < msixcnt; i++)
- device->msix_entries[i].entry = i;
-
- err = pci_enable_msix(device->pdev, device->msix_entries, msixcnt);
- if (err < 0)
- goto msi;
- if (err > 0)
- goto msix_single_vector;
-
- for (i = 0; i < msixcnt; i++) {
- ioat_chan = ioat_lookup_chan_by_index(device, i);
- err = request_irq(device->msix_entries[i].vector,
- ioat_dma_do_interrupt_msix,
- 0, "ioat-msix", ioat_chan);
- if (err) {
- for (j = 0; j < i; j++) {
- ioat_chan =
- ioat_lookup_chan_by_index(device, j);
- free_irq(device->msix_entries[j].vector,
- ioat_chan);
- }
- goto msix_single_vector;
- }
- }
- intrctrl |= IOAT_INTRCTRL_MSIX_VECTOR_CONTROL;
- device->irq_mode = msix_multi_vector;
- goto done;
-
-msix_single_vector:
- device->msix_entries[0].entry = 0;
- err = pci_enable_msix(device->pdev, device->msix_entries, 1);
- if (err)
- goto msi;
-
- err = request_irq(device->msix_entries[0].vector, ioat_dma_do_interrupt,
- 0, "ioat-msix", device);
- if (err) {
- pci_disable_msix(device->pdev);
- goto msi;
- }
- device->irq_mode = msix_single_vector;
- goto done;
-
-msi:
- err = pci_enable_msi(device->pdev);
- if (err)
- goto intx;
-
- err = request_irq(device->pdev->irq, ioat_dma_do_interrupt,
- 0, "ioat-msi", device);
- if (err) {
- pci_disable_msi(device->pdev);
- goto intx;
- }
- /*
- * CB 1.2 devices need a bit set in configuration space to enable MSI
- */
- if (device->version == IOAT_VER_1_2) {
- u32 dmactrl;
- pci_read_config_dword(device->pdev,
- IOAT_PCI_DMACTRL_OFFSET, &dmactrl);
- dmactrl |= IOAT_PCI_DMACTRL_MSI_EN;
- pci_write_config_dword(device->pdev,
- IOAT_PCI_DMACTRL_OFFSET, dmactrl);
- }
- device->irq_mode = msi;
- goto done;
-
-intx:
- err = request_irq(device->pdev->irq, ioat_dma_do_interrupt,
- IRQF_SHARED, "ioat-intx", device);
- if (err)
- goto err_no_irq;
- device->irq_mode = intx;
-
-done:
- intrctrl |= IOAT_INTRCTRL_MASTER_INT_EN;
- writeb(intrctrl, device->reg_base + IOAT_INTRCTRL_OFFSET);
- return 0;
-
-err_no_irq:
- /* Disable all interrupt generation */
- writeb(0, device->reg_base + IOAT_INTRCTRL_OFFSET);
- dev_err(&device->pdev->dev, "no usable interrupts\n");
- device->irq_mode = none;
- return -1;
-}
-
-/**
- * ioat_dma_remove_interrupts - remove whatever interrupts were set
- * @device: ioat device
- */
-static void ioat_dma_remove_interrupts(struct ioatdma_device *device)
-{
- struct ioat_dma_chan *ioat_chan;
- int i;
-
- /* Disable all interrupt generation */
- writeb(0, device->reg_base + IOAT_INTRCTRL_OFFSET);
-
- switch (device->irq_mode) {
- case msix_multi_vector:
- for (i = 0; i < device->common.chancnt; i++) {
- ioat_chan = ioat_lookup_chan_by_index(device, i);
- free_irq(device->msix_entries[i].vector, ioat_chan);
- }
- pci_disable_msix(device->pdev);
- break;
- case msix_single_vector:
- free_irq(device->msix_entries[0].vector, device);
- pci_disable_msix(device->pdev);
- break;
- case msi:
- free_irq(device->pdev->irq, device);
- pci_disable_msi(device->pdev);
- break;
- case intx:
- free_irq(device->pdev->irq, device);
- break;
- case none:
- dev_warn(&device->pdev->dev,
- "call to %s without interrupts setup\n", __func__);
- }
- device->irq_mode = none;
-}
-
-struct ioatdma_device *ioat_dma_probe(struct pci_dev *pdev,
- void __iomem *iobase)
-{
- int err;
- struct ioatdma_device *device;
-
- device = kzalloc(sizeof(*device), GFP_KERNEL);
- if (!device) {
- err = -ENOMEM;
- goto err_kzalloc;
- }
- device->pdev = pdev;
- device->reg_base = iobase;
- device->version = readb(device->reg_base + IOAT_VER_OFFSET);
-
- /* DMA coherent memory pool for DMA descriptor allocations */
- device->dma_pool = pci_pool_create("dma_desc_pool", pdev,
- sizeof(struct ioat_dma_descriptor),
- 64, 0);
- if (!device->dma_pool) {
- err = -ENOMEM;
- goto err_dma_pool;
- }
-
- device->completion_pool = pci_pool_create("completion_pool", pdev,
- sizeof(u64), SMP_CACHE_BYTES,
- SMP_CACHE_BYTES);
- if (!device->completion_pool) {
- err = -ENOMEM;
- goto err_completion_pool;
- }
-
- INIT_LIST_HEAD(&device->common.channels);
- ioat_dma_enumerate_channels(device);
-
- device->common.device_alloc_chan_resources =
- ioat_dma_alloc_chan_resources;
- device->common.device_free_chan_resources =
- ioat_dma_free_chan_resources;
- device->common.dev = &pdev->dev;
-
- dma_cap_set(DMA_MEMCPY, device->common.cap_mask);
- device->common.device_is_tx_complete = ioat_dma_is_complete;
- switch (device->version) {
- case IOAT_VER_1_2:
- device->common.device_prep_dma_memcpy = ioat1_dma_prep_memcpy;
- device->common.device_issue_pending =
- ioat1_dma_memcpy_issue_pending;
- break;
- case IOAT_VER_2_0:
- case IOAT_VER_3_0:
- device->common.device_prep_dma_memcpy = ioat2_dma_prep_memcpy;
- device->common.device_issue_pending =
- ioat2_dma_memcpy_issue_pending;
- break;
- }
-
- dev_err(&device->pdev->dev,
- "Intel(R) I/OAT DMA Engine found,"
- " %d channels, device version 0x%02x, driver version %s\n",
- device->common.chancnt, device->version, IOAT_DMA_VERSION);
-
- if (!device->common.chancnt) {
- dev_err(&device->pdev->dev,
- "Intel(R) I/OAT DMA Engine problem found: "
- "zero channels detected\n");
- goto err_setup_interrupts;
- }
-
- err = ioat_dma_setup_interrupts(device);
- if (err)
- goto err_setup_interrupts;
-
- err = ioat_dma_self_test(device);
- if (err)
- goto err_self_test;
-
- ioat_set_tcp_copy_break(device);
-
- dma_async_device_register(&device->common);
-
- if (device->version != IOAT_VER_3_0) {
- INIT_DELAYED_WORK(&device->work, ioat_dma_chan_watchdog);
- schedule_delayed_work(&device->work,
- WATCHDOG_DELAY);
- }
-
- return device;
-
-err_self_test:
- ioat_dma_remove_interrupts(device);
-err_setup_interrupts:
- pci_pool_destroy(device->completion_pool);
-err_completion_pool:
- pci_pool_destroy(device->dma_pool);
-err_dma_pool:
- kfree(device);
-err_kzalloc:
- dev_err(&pdev->dev,
- "Intel(R) I/OAT DMA Engine initialization failed\n");
- return NULL;
-}
-
-void ioat_dma_remove(struct ioatdma_device *device)
-{
- struct dma_chan *chan, *_chan;
- struct ioat_dma_chan *ioat_chan;
-
- if (device->version != IOAT_VER_3_0)
- cancel_delayed_work(&device->work);
-
- ioat_dma_remove_interrupts(device);
-
- dma_async_device_unregister(&device->common);
-
- pci_pool_destroy(device->dma_pool);
- pci_pool_destroy(device->completion_pool);
-
- iounmap(device->reg_base);
- pci_release_regions(device->pdev);
- pci_disable_device(device->pdev);
-
- list_for_each_entry_safe(chan, _chan,
- &device->common.channels, device_node) {
- ioat_chan = to_ioat_chan(chan);
- list_del(&chan->device_node);
- kfree(ioat_chan);
- }
- kfree(device);
-}
-
+++ /dev/null
-/*
- * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the Free
- * Software Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59
- * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- *
- * The full GNU General Public License is included in this distribution in the
- * file called COPYING.
- */
-#ifndef IOATDMA_H
-#define IOATDMA_H
-
-#include <linux/dmaengine.h>
-#include "ioatdma_hw.h"
-#include <linux/init.h>
-#include <linux/dmapool.h>
-#include <linux/cache.h>
-#include <linux/pci_ids.h>
-#include <net/tcp.h>
-
-#define IOAT_DMA_VERSION "3.64"
-
-enum ioat_interrupt {
- none = 0,
- msix_multi_vector = 1,
- msix_single_vector = 2,
- msi = 3,
- intx = 4,
-};
-
-#define IOAT_LOW_COMPLETION_MASK 0xffffffc0
-#define IOAT_DMA_DCA_ANY_CPU ~0
-#define IOAT_WATCHDOG_PERIOD (2 * HZ)
-
-
-/**
- * struct ioatdma_device - internal representation of a IOAT device
- * @pdev: PCI-Express device
- * @reg_base: MMIO register space base address
- * @dma_pool: for allocating DMA descriptors
- * @common: embedded struct dma_device
- * @version: version of ioatdma device
- * @irq_mode: which style irq to use
- * @msix_entries: irq handlers
- * @idx: per channel data
- */
-
-struct ioatdma_device {
- struct pci_dev *pdev;
- void __iomem *reg_base;
- struct pci_pool *dma_pool;
- struct pci_pool *completion_pool;
- struct dma_device common;
- u8 version;
- enum ioat_interrupt irq_mode;
- struct delayed_work work;
- struct msix_entry msix_entries[4];
- struct ioat_dma_chan *idx[4];
-};
-
-/**
- * struct ioat_dma_chan - internal representation of a DMA channel
- */
-struct ioat_dma_chan {
-
- void __iomem *reg_base;
-
- dma_cookie_t completed_cookie;
- unsigned long last_completion;
- unsigned long last_completion_time;
-
- size_t xfercap; /* XFERCAP register value expanded out */
-
- spinlock_t cleanup_lock;
- spinlock_t desc_lock;
- struct list_head free_desc;
- struct list_head used_desc;
- unsigned long watchdog_completion;
- int watchdog_tcp_cookie;
- u32 watchdog_last_tcp_cookie;
- struct delayed_work work;
-
- int pending;
- int dmacount;
- int desccount;
-
- struct ioatdma_device *device;
- struct dma_chan common;
-
- dma_addr_t completion_addr;
- union {
- u64 full; /* HW completion writeback */
- struct {
- u32 low;
- u32 high;
- };
- } *completion_virt;
- unsigned long last_compl_desc_addr_hw;
- struct tasklet_struct cleanup_task;
-};
-
-/* wrapper around hardware descriptor format + additional software fields */
-
-/**
- * struct ioat_desc_sw - wrapper around hardware descriptor
- * @hw: hardware DMA descriptor
- * @node: this descriptor will either be on the free list,
- * or attached to a transaction list (async_tx.tx_list)
- * @tx_cnt: number of descriptors required to complete the transaction
- * @async_tx: the generic software descriptor for all engines
- */
-struct ioat_desc_sw {
- struct ioat_dma_descriptor *hw;
- struct list_head node;
- int tx_cnt;
- size_t len;
- dma_addr_t src;
- dma_addr_t dst;
- struct dma_async_tx_descriptor async_tx;
-};
-
-static inline void ioat_set_tcp_copy_break(struct ioatdma_device *dev)
-{
- #ifdef CONFIG_NET_DMA
- switch (dev->version) {
- case IOAT_VER_1_2:
- sysctl_tcp_dma_copybreak = 4096;
- break;
- case IOAT_VER_2_0:
- sysctl_tcp_dma_copybreak = 2048;
- break;
- case IOAT_VER_3_0:
- sysctl_tcp_dma_copybreak = 262144;
- break;
- }
- #endif
-}
-
-#if defined(CONFIG_INTEL_IOATDMA) || defined(CONFIG_INTEL_IOATDMA_MODULE)
-struct ioatdma_device *ioat_dma_probe(struct pci_dev *pdev,
- void __iomem *iobase);
-void ioat_dma_remove(struct ioatdma_device *device);
-struct dca_provider *ioat_dca_init(struct pci_dev *pdev, void __iomem *iobase);
-struct dca_provider *ioat2_dca_init(struct pci_dev *pdev, void __iomem *iobase);
-struct dca_provider *ioat3_dca_init(struct pci_dev *pdev, void __iomem *iobase);
-#else
-#define ioat_dma_probe(pdev, iobase) NULL
-#define ioat_dma_remove(device) do { } while (0)
-#define ioat_dca_init(pdev, iobase) NULL
-#define ioat2_dca_init(pdev, iobase) NULL
-#define ioat3_dca_init(pdev, iobase) NULL
-#endif
-
-#endif /* IOATDMA_H */
+++ /dev/null
-/*
- * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the Free
- * Software Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59
- * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- *
- * The full GNU General Public License is included in this distribution in the
- * file called COPYING.
- */
-#ifndef _IOAT_HW_H_
-#define _IOAT_HW_H_
-
-/* PCI Configuration Space Values */
-#define IOAT_PCI_VID 0x8086
-
-/* CB device ID's */
-#define IOAT_PCI_DID_5000 0x1A38
-#define IOAT_PCI_DID_CNB 0x360B
-#define IOAT_PCI_DID_SCNB 0x65FF
-#define IOAT_PCI_DID_SNB 0x402F
-
-#define IOAT_PCI_RID 0x00
-#define IOAT_PCI_SVID 0x8086
-#define IOAT_PCI_SID 0x8086
-#define IOAT_VER_1_2 0x12 /* Version 1.2 */
-#define IOAT_VER_2_0 0x20 /* Version 2.0 */
-#define IOAT_VER_3_0 0x30 /* Version 3.0 */
-
-struct ioat_dma_descriptor {
- uint32_t size;
- uint32_t ctl;
- uint64_t src_addr;
- uint64_t dst_addr;
- uint64_t next;
- uint64_t rsv1;
- uint64_t rsv2;
- uint64_t user1;
- uint64_t user2;
-};
-
-#define IOAT_DMA_DESCRIPTOR_CTL_INT_GN 0x00000001
-#define IOAT_DMA_DESCRIPTOR_CTL_SRC_SN 0x00000002
-#define IOAT_DMA_DESCRIPTOR_CTL_DST_SN 0x00000004
-#define IOAT_DMA_DESCRIPTOR_CTL_CP_STS 0x00000008
-#define IOAT_DMA_DESCRIPTOR_CTL_FRAME 0x00000010
-#define IOAT_DMA_DESCRIPTOR_NUL 0x00000020
-#define IOAT_DMA_DESCRIPTOR_CTL_SP_BRK 0x00000040
-#define IOAT_DMA_DESCRIPTOR_CTL_DP_BRK 0x00000080
-#define IOAT_DMA_DESCRIPTOR_CTL_BNDL 0x00000100
-#define IOAT_DMA_DESCRIPTOR_CTL_DCA 0x00000200
-#define IOAT_DMA_DESCRIPTOR_CTL_BUFHINT 0x00000400
-
-#define IOAT_DMA_DESCRIPTOR_CTL_OPCODE_CONTEXT 0xFF000000
-#define IOAT_DMA_DESCRIPTOR_CTL_OPCODE_DMA 0x00000000
-
-#define IOAT_DMA_DESCRIPTOR_CTL_CONTEXT_DCA 0x00000001
-#define IOAT_DMA_DESCRIPTOR_CTL_OPCODE_MASK 0xFF000000
-
-#endif
+++ /dev/null
-/*
- * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the Free
- * Software Foundation; either version 2 of the License, or (at your option)
- * any later version.
- *
- * This program is distributed in the hope that it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- * more details.
- *
- * You should have received a copy of the GNU General Public License along with
- * this program; if not, write to the Free Software Foundation, Inc., 59
- * Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- *
- * The full GNU General Public License is included in this distribution in the
- * file called COPYING.
- */
-#ifndef _IOAT_REGISTERS_H_
-#define _IOAT_REGISTERS_H_
-
-#define IOAT_PCI_DMACTRL_OFFSET 0x48
-#define IOAT_PCI_DMACTRL_DMA_EN 0x00000001
-#define IOAT_PCI_DMACTRL_MSI_EN 0x00000002
-
-#define IOAT_PCI_DEVICE_ID_OFFSET 0x02
-#define IOAT_PCI_DMAUNCERRSTS_OFFSET 0x148
-#define IOAT_PCI_CHANERRMASK_INT_OFFSET 0x184
-
-/* MMIO Device Registers */
-#define IOAT_CHANCNT_OFFSET 0x00 /* 8-bit */
-
-#define IOAT_XFERCAP_OFFSET 0x01 /* 8-bit */
-#define IOAT_XFERCAP_4KB 12
-#define IOAT_XFERCAP_8KB 13
-#define IOAT_XFERCAP_16KB 14
-#define IOAT_XFERCAP_32KB 15
-#define IOAT_XFERCAP_32GB 0
-
-#define IOAT_GENCTRL_OFFSET 0x02 /* 8-bit */
-#define IOAT_GENCTRL_DEBUG_EN 0x01
-
-#define IOAT_INTRCTRL_OFFSET 0x03 /* 8-bit */
-#define IOAT_INTRCTRL_MASTER_INT_EN 0x01 /* Master Interrupt Enable */
-#define IOAT_INTRCTRL_INT_STATUS 0x02 /* ATTNSTATUS -or- Channel Int */
-#define IOAT_INTRCTRL_INT 0x04 /* INT_STATUS -and- MASTER_INT_EN */
-#define IOAT_INTRCTRL_MSIX_VECTOR_CONTROL 0x08 /* Enable all MSI-X vectors */
-
-#define IOAT_ATTNSTATUS_OFFSET 0x04 /* Each bit is a channel */
-
-#define IOAT_VER_OFFSET 0x08 /* 8-bit */
-#define IOAT_VER_MAJOR_MASK 0xF0
-#define IOAT_VER_MINOR_MASK 0x0F
-#define GET_IOAT_VER_MAJOR(x) (((x) & IOAT_VER_MAJOR_MASK) >> 4)
-#define GET_IOAT_VER_MINOR(x) ((x) & IOAT_VER_MINOR_MASK)
-
-#define IOAT_PERPORTOFFSET_OFFSET 0x0A /* 16-bit */
-
-#define IOAT_INTRDELAY_OFFSET 0x0C /* 16-bit */
-#define IOAT_INTRDELAY_INT_DELAY_MASK 0x3FFF /* Interrupt Delay Time */
-#define IOAT_INTRDELAY_COALESE_SUPPORT 0x8000 /* Interrupt Coalescing Supported */
-
-#define IOAT_DEVICE_STATUS_OFFSET 0x0E /* 16-bit */
-#define IOAT_DEVICE_STATUS_DEGRADED_MODE 0x0001
-
-#define IOAT_CHANNEL_MMIO_SIZE 0x80 /* Each Channel MMIO space is this size */
-
-/* DMA Channel Registers */
-#define IOAT_CHANCTRL_OFFSET 0x00 /* 16-bit Channel Control Register */
-#define IOAT_CHANCTRL_CHANNEL_PRIORITY_MASK 0xF000
-#define IOAT_CHANCTRL_CHANNEL_IN_USE 0x0100
-#define IOAT_CHANCTRL_DESCRIPTOR_ADDR_SNOOP_CONTROL 0x0020
-#define IOAT_CHANCTRL_ERR_INT_EN 0x0010
-#define IOAT_CHANCTRL_ANY_ERR_ABORT_EN 0x0008
-#define IOAT_CHANCTRL_ERR_COMPLETION_EN 0x0004
-#define IOAT_CHANCTRL_INT_DISABLE 0x0001
-
-#define IOAT_DMA_COMP_OFFSET 0x02 /* 16-bit DMA channel compatibility */
-#define IOAT_DMA_COMP_V1 0x0001 /* Compatibility with DMA version 1 */
-#define IOAT_DMA_COMP_V2 0x0002 /* Compatibility with DMA version 2 */
-
-
-#define IOAT1_CHANSTS_OFFSET 0x04 /* 64-bit Channel Status Register */
-#define IOAT2_CHANSTS_OFFSET 0x08 /* 64-bit Channel Status Register */
-#define IOAT_CHANSTS_OFFSET(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHANSTS_OFFSET : IOAT2_CHANSTS_OFFSET)
-#define IOAT1_CHANSTS_OFFSET_LOW 0x04
-#define IOAT2_CHANSTS_OFFSET_LOW 0x08
-#define IOAT_CHANSTS_OFFSET_LOW(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHANSTS_OFFSET_LOW : IOAT2_CHANSTS_OFFSET_LOW)
-#define IOAT1_CHANSTS_OFFSET_HIGH 0x08
-#define IOAT2_CHANSTS_OFFSET_HIGH 0x0C
-#define IOAT_CHANSTS_OFFSET_HIGH(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHANSTS_OFFSET_HIGH : IOAT2_CHANSTS_OFFSET_HIGH)
-#define IOAT_CHANSTS_COMPLETED_DESCRIPTOR_ADDR ~0x3F
-#define IOAT_CHANSTS_SOFT_ERR 0x0000000000000010
-#define IOAT_CHANSTS_UNAFFILIATED_ERR 0x0000000000000008
-#define IOAT_CHANSTS_DMA_TRANSFER_STATUS 0x0000000000000007
-#define IOAT_CHANSTS_DMA_TRANSFER_STATUS_ACTIVE 0x0
-#define IOAT_CHANSTS_DMA_TRANSFER_STATUS_DONE 0x1
-#define IOAT_CHANSTS_DMA_TRANSFER_STATUS_SUSPENDED 0x2
-#define IOAT_CHANSTS_DMA_TRANSFER_STATUS_HALTED 0x3
-
-
-
-#define IOAT_CHAN_DMACOUNT_OFFSET 0x06 /* 16-bit DMA Count register */
-
-#define IOAT_DCACTRL_OFFSET 0x30 /* 32 bit Direct Cache Access Control Register */
-#define IOAT_DCACTRL_CMPL_WRITE_ENABLE 0x10000
-#define IOAT_DCACTRL_TARGET_CPU_MASK 0xFFFF /* APIC ID */
-
-/* CB DCA Memory Space Registers */
-#define IOAT_DCAOFFSET_OFFSET 0x14
-/* CB_BAR + IOAT_DCAOFFSET value */
-#define IOAT_DCA_VER_OFFSET 0x00
-#define IOAT_DCA_VER_MAJOR_MASK 0xF0
-#define IOAT_DCA_VER_MINOR_MASK 0x0F
-
-#define IOAT_DCA_COMP_OFFSET 0x02
-#define IOAT_DCA_COMP_V1 0x1
-
-#define IOAT_FSB_CAPABILITY_OFFSET 0x04
-#define IOAT_FSB_CAPABILITY_PREFETCH 0x1
-
-#define IOAT_PCI_CAPABILITY_OFFSET 0x06
-#define IOAT_PCI_CAPABILITY_MEMWR 0x1
-
-#define IOAT_FSB_CAP_ENABLE_OFFSET 0x08
-#define IOAT_FSB_CAP_ENABLE_PREFETCH 0x1
-
-#define IOAT_PCI_CAP_ENABLE_OFFSET 0x0A
-#define IOAT_PCI_CAP_ENABLE_MEMWR 0x1
-
-#define IOAT_APICID_TAG_MAP_OFFSET 0x0C
-#define IOAT_APICID_TAG_MAP_TAG0 0x0000000F
-#define IOAT_APICID_TAG_MAP_TAG0_SHIFT 0
-#define IOAT_APICID_TAG_MAP_TAG1 0x000000F0
-#define IOAT_APICID_TAG_MAP_TAG1_SHIFT 4
-#define IOAT_APICID_TAG_MAP_TAG2 0x00000F00
-#define IOAT_APICID_TAG_MAP_TAG2_SHIFT 8
-#define IOAT_APICID_TAG_MAP_TAG3 0x0000F000
-#define IOAT_APICID_TAG_MAP_TAG3_SHIFT 12
-#define IOAT_APICID_TAG_MAP_TAG4 0x000F0000
-#define IOAT_APICID_TAG_MAP_TAG4_SHIFT 16
-#define IOAT_APICID_TAG_CB2_VALID 0x8080808080
-
-#define IOAT_DCA_GREQID_OFFSET 0x10
-#define IOAT_DCA_GREQID_SIZE 0x04
-#define IOAT_DCA_GREQID_MASK 0xFFFF
-#define IOAT_DCA_GREQID_IGNOREFUN 0x10000000
-#define IOAT_DCA_GREQID_VALID 0x20000000
-#define IOAT_DCA_GREQID_LASTID 0x80000000
-
-#define IOAT3_CSI_CAPABILITY_OFFSET 0x08
-#define IOAT3_CSI_CAPABILITY_PREFETCH 0x1
-
-#define IOAT3_PCI_CAPABILITY_OFFSET 0x0A
-#define IOAT3_PCI_CAPABILITY_MEMWR 0x1
-
-#define IOAT3_CSI_CONTROL_OFFSET 0x0C
-#define IOAT3_CSI_CONTROL_PREFETCH 0x1
-
-#define IOAT3_PCI_CONTROL_OFFSET 0x0E
-#define IOAT3_PCI_CONTROL_MEMWR 0x1
-
-#define IOAT3_APICID_TAG_MAP_OFFSET 0x10
-#define IOAT3_APICID_TAG_MAP_OFFSET_LOW 0x10
-#define IOAT3_APICID_TAG_MAP_OFFSET_HIGH 0x14
-
-#define IOAT3_DCA_GREQID_OFFSET 0x02
-
-#define IOAT1_CHAINADDR_OFFSET 0x0C /* 64-bit Descriptor Chain Address Register */
-#define IOAT2_CHAINADDR_OFFSET 0x10 /* 64-bit Descriptor Chain Address Register */
-#define IOAT_CHAINADDR_OFFSET(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHAINADDR_OFFSET : IOAT2_CHAINADDR_OFFSET)
-#define IOAT1_CHAINADDR_OFFSET_LOW 0x0C
-#define IOAT2_CHAINADDR_OFFSET_LOW 0x10
-#define IOAT_CHAINADDR_OFFSET_LOW(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHAINADDR_OFFSET_LOW : IOAT2_CHAINADDR_OFFSET_LOW)
-#define IOAT1_CHAINADDR_OFFSET_HIGH 0x10
-#define IOAT2_CHAINADDR_OFFSET_HIGH 0x14
-#define IOAT_CHAINADDR_OFFSET_HIGH(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHAINADDR_OFFSET_HIGH : IOAT2_CHAINADDR_OFFSET_HIGH)
-
-#define IOAT1_CHANCMD_OFFSET 0x14 /* 8-bit DMA Channel Command Register */
-#define IOAT2_CHANCMD_OFFSET 0x04 /* 8-bit DMA Channel Command Register */
-#define IOAT_CHANCMD_OFFSET(ver) ((ver) < IOAT_VER_2_0 \
- ? IOAT1_CHANCMD_OFFSET : IOAT2_CHANCMD_OFFSET)
-#define IOAT_CHANCMD_RESET 0x20
-#define IOAT_CHANCMD_RESUME 0x10
-#define IOAT_CHANCMD_ABORT 0x08
-#define IOAT_CHANCMD_SUSPEND 0x04
-#define IOAT_CHANCMD_APPEND 0x02
-#define IOAT_CHANCMD_START 0x01
-
-#define IOAT_CHANCMP_OFFSET 0x18 /* 64-bit Channel Completion Address Register */
-#define IOAT_CHANCMP_OFFSET_LOW 0x18
-#define IOAT_CHANCMP_OFFSET_HIGH 0x1C
-
-#define IOAT_CDAR_OFFSET 0x20 /* 64-bit Current Descriptor Address Register */
-#define IOAT_CDAR_OFFSET_LOW 0x20
-#define IOAT_CDAR_OFFSET_HIGH 0x24
-
-#define IOAT_CHANERR_OFFSET 0x28 /* 32-bit Channel Error Register */
-#define IOAT_CHANERR_DMA_TRANSFER_SRC_ADDR_ERR 0x0001
-#define IOAT_CHANERR_DMA_TRANSFER_DEST_ADDR_ERR 0x0002
-#define IOAT_CHANERR_NEXT_DESCRIPTOR_ADDR_ERR 0x0004
-#define IOAT_CHANERR_NEXT_DESCRIPTOR_ALIGNMENT_ERR 0x0008
-#define IOAT_CHANERR_CHAIN_ADDR_VALUE_ERR 0x0010
-#define IOAT_CHANERR_CHANCMD_ERR 0x0020
-#define IOAT_CHANERR_CHIPSET_UNCORRECTABLE_DATA_INTEGRITY_ERR 0x0040
-#define IOAT_CHANERR_DMA_UNCORRECTABLE_DATA_INTEGRITY_ERR 0x0080
-#define IOAT_CHANERR_READ_DATA_ERR 0x0100
-#define IOAT_CHANERR_WRITE_DATA_ERR 0x0200
-#define IOAT_CHANERR_DESCRIPTOR_CONTROL_ERR 0x0400
-#define IOAT_CHANERR_DESCRIPTOR_LENGTH_ERR 0x0800
-#define IOAT_CHANERR_COMPLETION_ADDR_ERR 0x1000
-#define IOAT_CHANERR_INT_CONFIGURATION_ERR 0x2000
-#define IOAT_CHANERR_SOFT_ERR 0x4000
-#define IOAT_CHANERR_UNAFFILIATED_ERR 0x8000
-
-#define IOAT_CHANERR_MASK_OFFSET 0x2C /* 32-bit Channel Error Register */
-
-#endif /* _IOAT_REGISTERS_H_ */
#include <linux/platform_device.h>
#include <linux/memory.h>
#include <linux/ioport.h>
+#include <linux/raid/pq.h>
#include <mach/adma.h>
}
}
+static void
+iop_desc_unmap(struct iop_adma_chan *iop_chan, struct iop_adma_desc_slot *desc)
+{
+ struct dma_async_tx_descriptor *tx = &desc->async_tx;
+ struct iop_adma_desc_slot *unmap = desc->group_head;
+ struct device *dev = &iop_chan->device->pdev->dev;
+ u32 len = unmap->unmap_len;
+ enum dma_ctrl_flags flags = tx->flags;
+ u32 src_cnt;
+ dma_addr_t addr;
+ dma_addr_t dest;
+
+ src_cnt = unmap->unmap_src_cnt;
+ dest = iop_desc_get_dest_addr(unmap, iop_chan);
+ if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+ enum dma_data_direction dir;
+
+ if (src_cnt > 1) /* is xor? */
+ dir = DMA_BIDIRECTIONAL;
+ else
+ dir = DMA_FROM_DEVICE;
+
+ dma_unmap_page(dev, dest, len, dir);
+ }
+
+ if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ while (src_cnt--) {
+ addr = iop_desc_get_src_addr(unmap, iop_chan, src_cnt);
+ if (addr == dest)
+ continue;
+ dma_unmap_page(dev, addr, len, DMA_TO_DEVICE);
+ }
+ }
+ desc->group_head = NULL;
+}
+
+static void
+iop_desc_unmap_pq(struct iop_adma_chan *iop_chan, struct iop_adma_desc_slot *desc)
+{
+ struct dma_async_tx_descriptor *tx = &desc->async_tx;
+ struct iop_adma_desc_slot *unmap = desc->group_head;
+ struct device *dev = &iop_chan->device->pdev->dev;
+ u32 len = unmap->unmap_len;
+ enum dma_ctrl_flags flags = tx->flags;
+ u32 src_cnt = unmap->unmap_src_cnt;
+ dma_addr_t pdest = iop_desc_get_dest_addr(unmap, iop_chan);
+ dma_addr_t qdest = iop_desc_get_qdest_addr(unmap, iop_chan);
+ int i;
+
+ if (tx->flags & DMA_PREP_CONTINUE)
+ src_cnt -= 3;
+
+ if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP) && !desc->pq_check_result) {
+ dma_unmap_page(dev, pdest, len, DMA_BIDIRECTIONAL);
+ dma_unmap_page(dev, qdest, len, DMA_BIDIRECTIONAL);
+ }
+
+ if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ dma_addr_t addr;
+
+ for (i = 0; i < src_cnt; i++) {
+ addr = iop_desc_get_src_addr(unmap, iop_chan, i);
+ dma_unmap_page(dev, addr, len, DMA_TO_DEVICE);
+ }
+ if (desc->pq_check_result) {
+ dma_unmap_page(dev, pdest, len, DMA_TO_DEVICE);
+ dma_unmap_page(dev, qdest, len, DMA_TO_DEVICE);
+ }
+ }
+
+ desc->group_head = NULL;
+}
+
+
static dma_cookie_t
iop_adma_run_tx_complete_actions(struct iop_adma_desc_slot *desc,
struct iop_adma_chan *iop_chan, dma_cookie_t cookie)
{
- BUG_ON(desc->async_tx.cookie < 0);
- if (desc->async_tx.cookie > 0) {
- cookie = desc->async_tx.cookie;
- desc->async_tx.cookie = 0;
+ struct dma_async_tx_descriptor *tx = &desc->async_tx;
+
+ BUG_ON(tx->cookie < 0);
+ if (tx->cookie > 0) {
+ cookie = tx->cookie;
+ tx->cookie = 0;
/* call the callback (must not sleep or submit new
* operations to this channel)
*/
- if (desc->async_tx.callback)
- desc->async_tx.callback(
- desc->async_tx.callback_param);
+ if (tx->callback)
+ tx->callback(tx->callback_param);
/* unmap dma addresses
* (unmap_single vs unmap_page?)
*/
if (desc->group_head && desc->unmap_len) {
- struct iop_adma_desc_slot *unmap = desc->group_head;
- struct device *dev =
- &iop_chan->device->pdev->dev;
- u32 len = unmap->unmap_len;
- enum dma_ctrl_flags flags = desc->async_tx.flags;
- u32 src_cnt;
- dma_addr_t addr;
- dma_addr_t dest;
-
- src_cnt = unmap->unmap_src_cnt;
- dest = iop_desc_get_dest_addr(unmap, iop_chan);
- if (!(flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
- enum dma_data_direction dir;
-
- if (src_cnt > 1) /* is xor? */
- dir = DMA_BIDIRECTIONAL;
- else
- dir = DMA_FROM_DEVICE;
-
- dma_unmap_page(dev, dest, len, dir);
- }
-
- if (!(flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
- while (src_cnt--) {
- addr = iop_desc_get_src_addr(unmap,
- iop_chan,
- src_cnt);
- if (addr == dest)
- continue;
- dma_unmap_page(dev, addr, len,
- DMA_TO_DEVICE);
- }
- }
- desc->group_head = NULL;
+ if (iop_desc_is_pq(desc))
+ iop_desc_unmap_pq(iop_chan, desc);
+ else
+ iop_desc_unmap(iop_chan, desc);
}
}
/* run dependent operations */
- dma_run_dependencies(&desc->async_tx);
+ dma_run_dependencies(tx);
return cookie;
}
{
struct iop_adma_chan *iop_chan = (struct iop_adma_chan *) data;
- spin_lock(&iop_chan->lock);
+ /* lockdep will flag depedency submissions as potentially
+ * recursive locking, this is not the case as a dependency
+ * submission will never recurse a channels submit routine.
+ * There are checks in async_tx.c to prevent this.
+ */
+ spin_lock_nested(&iop_chan->lock, SINGLE_DEPTH_NESTING);
__iop_adma_slot_cleanup(iop_chan);
spin_unlock(&iop_chan->lock);
}
}
alloc_tail->group_head = alloc_start;
alloc_tail->async_tx.cookie = -EBUSY;
- list_splice(&chain, &alloc_tail->async_tx.tx_list);
+ list_splice(&chain, &alloc_tail->tx_list);
iop_chan->last_used = last_used;
iop_desc_clear_next_desc(alloc_start);
iop_desc_clear_next_desc(alloc_tail);
old_chain_tail = list_entry(iop_chan->chain.prev,
struct iop_adma_desc_slot, chain_node);
- list_splice_init(&sw_desc->async_tx.tx_list,
+ list_splice_init(&sw_desc->tx_list,
&old_chain_tail->chain_node);
/* fix up the hardware chain */
dma_async_tx_descriptor_init(&slot->async_tx, chan);
slot->async_tx.tx_submit = iop_adma_tx_submit;
+ INIT_LIST_HEAD(&slot->tx_list);
INIT_LIST_HEAD(&slot->chain_node);
INIT_LIST_HEAD(&slot->slot_node);
hw_desc = (char *) iop_chan->device->dma_desc_pool;
}
static struct dma_async_tx_descriptor *
-iop_adma_prep_dma_zero_sum(struct dma_chan *chan, dma_addr_t *dma_src,
- unsigned int src_cnt, size_t len, u32 *result,
- unsigned long flags)
+iop_adma_prep_dma_xor_val(struct dma_chan *chan, dma_addr_t *dma_src,
+ unsigned int src_cnt, size_t len, u32 *result,
+ unsigned long flags)
{
struct iop_adma_chan *iop_chan = to_iop_adma_chan(chan);
struct iop_adma_desc_slot *sw_desc, *grp_start;
return sw_desc ? &sw_desc->async_tx : NULL;
}
+static struct dma_async_tx_descriptor *
+iop_adma_prep_dma_pq(struct dma_chan *chan, dma_addr_t *dst, dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf, size_t len,
+ unsigned long flags)
+{
+ struct iop_adma_chan *iop_chan = to_iop_adma_chan(chan);
+ struct iop_adma_desc_slot *sw_desc, *g;
+ int slot_cnt, slots_per_op;
+ int continue_srcs;
+
+ if (unlikely(!len))
+ return NULL;
+ BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
+
+ dev_dbg(iop_chan->device->common.dev,
+ "%s src_cnt: %d len: %u flags: %lx\n",
+ __func__, src_cnt, len, flags);
+
+ if (dmaf_p_disabled_continue(flags))
+ continue_srcs = 1+src_cnt;
+ else if (dmaf_continue(flags))
+ continue_srcs = 3+src_cnt;
+ else
+ continue_srcs = 0+src_cnt;
+
+ spin_lock_bh(&iop_chan->lock);
+ slot_cnt = iop_chan_pq_slot_count(len, continue_srcs, &slots_per_op);
+ sw_desc = iop_adma_alloc_slots(iop_chan, slot_cnt, slots_per_op);
+ if (sw_desc) {
+ int i;
+
+ g = sw_desc->group_head;
+ iop_desc_set_byte_count(g, iop_chan, len);
+
+ /* even if P is disabled its destination address (bits
+ * [3:0]) must match Q. It is ok if P points to an
+ * invalid address, it won't be written.
+ */
+ if (flags & DMA_PREP_PQ_DISABLE_P)
+ dst[0] = dst[1] & 0x7;
+
+ iop_desc_set_pq_addr(g, dst);
+ sw_desc->unmap_src_cnt = src_cnt;
+ sw_desc->unmap_len = len;
+ sw_desc->async_tx.flags = flags;
+ for (i = 0; i < src_cnt; i++)
+ iop_desc_set_pq_src_addr(g, i, src[i], scf[i]);
+
+ /* if we are continuing a previous operation factor in
+ * the old p and q values, see the comment for dma_maxpq
+ * in include/linux/dmaengine.h
+ */
+ if (dmaf_p_disabled_continue(flags))
+ iop_desc_set_pq_src_addr(g, i++, dst[1], 1);
+ else if (dmaf_continue(flags)) {
+ iop_desc_set_pq_src_addr(g, i++, dst[0], 0);
+ iop_desc_set_pq_src_addr(g, i++, dst[1], 1);
+ iop_desc_set_pq_src_addr(g, i++, dst[1], 0);
+ }
+ iop_desc_init_pq(g, i, flags);
+ }
+ spin_unlock_bh(&iop_chan->lock);
+
+ return sw_desc ? &sw_desc->async_tx : NULL;
+}
+
+static struct dma_async_tx_descriptor *
+iop_adma_prep_dma_pq_val(struct dma_chan *chan, dma_addr_t *pq, dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf,
+ size_t len, enum sum_check_flags *pqres,
+ unsigned long flags)
+{
+ struct iop_adma_chan *iop_chan = to_iop_adma_chan(chan);
+ struct iop_adma_desc_slot *sw_desc, *g;
+ int slot_cnt, slots_per_op;
+
+ if (unlikely(!len))
+ return NULL;
+ BUG_ON(len > IOP_ADMA_XOR_MAX_BYTE_COUNT);
+
+ dev_dbg(iop_chan->device->common.dev, "%s src_cnt: %d len: %u\n",
+ __func__, src_cnt, len);
+
+ spin_lock_bh(&iop_chan->lock);
+ slot_cnt = iop_chan_pq_zero_sum_slot_count(len, src_cnt + 2, &slots_per_op);
+ sw_desc = iop_adma_alloc_slots(iop_chan, slot_cnt, slots_per_op);
+ if (sw_desc) {
+ /* for validate operations p and q are tagged onto the
+ * end of the source list
+ */
+ int pq_idx = src_cnt;
+
+ g = sw_desc->group_head;
+ iop_desc_init_pq_zero_sum(g, src_cnt+2, flags);
+ iop_desc_set_pq_zero_sum_byte_count(g, len);
+ g->pq_check_result = pqres;
+ pr_debug("\t%s: g->pq_check_result: %p\n",
+ __func__, g->pq_check_result);
+ sw_desc->unmap_src_cnt = src_cnt+2;
+ sw_desc->unmap_len = len;
+ sw_desc->async_tx.flags = flags;
+ while (src_cnt--)
+ iop_desc_set_pq_zero_sum_src_addr(g, src_cnt,
+ src[src_cnt],
+ scf[src_cnt]);
+ iop_desc_set_pq_zero_sum_addr(g, pq_idx, src);
+ }
+ spin_unlock_bh(&iop_chan->lock);
+
+ return sw_desc ? &sw_desc->async_tx : NULL;
+}
+
static void iop_adma_free_chan_resources(struct dma_chan *chan)
{
struct iop_adma_chan *iop_chan = to_iop_adma_chan(chan);
#define IOP_ADMA_NUM_SRC_TEST 4 /* must be <= 15 */
static int __devinit
-iop_adma_xor_zero_sum_self_test(struct iop_adma_device *device)
+iop_adma_xor_val_self_test(struct iop_adma_device *device)
{
int i, src_idx;
struct page *dest;
PAGE_SIZE, DMA_TO_DEVICE);
/* skip zero sum if the capability is not present */
- if (!dma_has_cap(DMA_ZERO_SUM, dma_chan->device->cap_mask))
+ if (!dma_has_cap(DMA_XOR_VAL, dma_chan->device->cap_mask))
goto free_resources;
/* zero sum the sources with the destintation page */
dma_srcs[i] = dma_map_page(dma_chan->device->dev,
zero_sum_srcs[i], 0, PAGE_SIZE,
DMA_TO_DEVICE);
- tx = iop_adma_prep_dma_zero_sum(dma_chan, dma_srcs,
- IOP_ADMA_NUM_SRC_TEST + 1, PAGE_SIZE,
- &zero_sum_result,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ tx = iop_adma_prep_dma_xor_val(dma_chan, dma_srcs,
+ IOP_ADMA_NUM_SRC_TEST + 1, PAGE_SIZE,
+ &zero_sum_result,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
cookie = iop_adma_tx_submit(tx);
iop_adma_issue_pending(dma_chan);
dma_srcs[i] = dma_map_page(dma_chan->device->dev,
zero_sum_srcs[i], 0, PAGE_SIZE,
DMA_TO_DEVICE);
- tx = iop_adma_prep_dma_zero_sum(dma_chan, dma_srcs,
- IOP_ADMA_NUM_SRC_TEST + 1, PAGE_SIZE,
- &zero_sum_result,
- DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ tx = iop_adma_prep_dma_xor_val(dma_chan, dma_srcs,
+ IOP_ADMA_NUM_SRC_TEST + 1, PAGE_SIZE,
+ &zero_sum_result,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
cookie = iop_adma_tx_submit(tx);
iop_adma_issue_pending(dma_chan);
return err;
}
+#ifdef CONFIG_MD_RAID6_PQ
+static int __devinit
+iop_adma_pq_zero_sum_self_test(struct iop_adma_device *device)
+{
+ /* combined sources, software pq results, and extra hw pq results */
+ struct page *pq[IOP_ADMA_NUM_SRC_TEST+2+2];
+ /* ptr to the extra hw pq buffers defined above */
+ struct page **pq_hw = &pq[IOP_ADMA_NUM_SRC_TEST+2];
+ /* address conversion buffers (dma_map / page_address) */
+ void *pq_sw[IOP_ADMA_NUM_SRC_TEST+2];
+ dma_addr_t pq_src[IOP_ADMA_NUM_SRC_TEST];
+ dma_addr_t pq_dest[2];
+
+ int i;
+ struct dma_async_tx_descriptor *tx;
+ struct dma_chan *dma_chan;
+ dma_cookie_t cookie;
+ u32 zero_sum_result;
+ int err = 0;
+ struct device *dev;
+
+ dev_dbg(device->common.dev, "%s\n", __func__);
+
+ for (i = 0; i < ARRAY_SIZE(pq); i++) {
+ pq[i] = alloc_page(GFP_KERNEL);
+ if (!pq[i]) {
+ while (i--)
+ __free_page(pq[i]);
+ return -ENOMEM;
+ }
+ }
+
+ /* Fill in src buffers */
+ for (i = 0; i < IOP_ADMA_NUM_SRC_TEST; i++) {
+ pq_sw[i] = page_address(pq[i]);
+ memset(pq_sw[i], 0x11111111 * (1<<i), PAGE_SIZE);
+ }
+ pq_sw[i] = page_address(pq[i]);
+ pq_sw[i+1] = page_address(pq[i+1]);
+
+ dma_chan = container_of(device->common.channels.next,
+ struct dma_chan,
+ device_node);
+ if (iop_adma_alloc_chan_resources(dma_chan) < 1) {
+ err = -ENODEV;
+ goto out;
+ }
+
+ dev = dma_chan->device->dev;
+
+ /* initialize the dests */
+ memset(page_address(pq_hw[0]), 0 , PAGE_SIZE);
+ memset(page_address(pq_hw[1]), 0 , PAGE_SIZE);
+
+ /* test pq */
+ pq_dest[0] = dma_map_page(dev, pq_hw[0], 0, PAGE_SIZE, DMA_FROM_DEVICE);
+ pq_dest[1] = dma_map_page(dev, pq_hw[1], 0, PAGE_SIZE, DMA_FROM_DEVICE);
+ for (i = 0; i < IOP_ADMA_NUM_SRC_TEST; i++)
+ pq_src[i] = dma_map_page(dev, pq[i], 0, PAGE_SIZE,
+ DMA_TO_DEVICE);
+
+ tx = iop_adma_prep_dma_pq(dma_chan, pq_dest, pq_src,
+ IOP_ADMA_NUM_SRC_TEST, (u8 *)raid6_gfexp,
+ PAGE_SIZE,
+ DMA_PREP_INTERRUPT |
+ DMA_CTRL_ACK);
+
+ cookie = iop_adma_tx_submit(tx);
+ iop_adma_issue_pending(dma_chan);
+ msleep(8);
+
+ if (iop_adma_is_complete(dma_chan, cookie, NULL, NULL) !=
+ DMA_SUCCESS) {
+ dev_err(dev, "Self-test pq timed out, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ raid6_call.gen_syndrome(IOP_ADMA_NUM_SRC_TEST+2, PAGE_SIZE, pq_sw);
+
+ if (memcmp(pq_sw[IOP_ADMA_NUM_SRC_TEST],
+ page_address(pq_hw[0]), PAGE_SIZE) != 0) {
+ dev_err(dev, "Self-test p failed compare, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+ if (memcmp(pq_sw[IOP_ADMA_NUM_SRC_TEST+1],
+ page_address(pq_hw[1]), PAGE_SIZE) != 0) {
+ dev_err(dev, "Self-test q failed compare, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ /* test correct zero sum using the software generated pq values */
+ for (i = 0; i < IOP_ADMA_NUM_SRC_TEST + 2; i++)
+ pq_src[i] = dma_map_page(dev, pq[i], 0, PAGE_SIZE,
+ DMA_TO_DEVICE);
+
+ zero_sum_result = ~0;
+ tx = iop_adma_prep_dma_pq_val(dma_chan, &pq_src[IOP_ADMA_NUM_SRC_TEST],
+ pq_src, IOP_ADMA_NUM_SRC_TEST,
+ raid6_gfexp, PAGE_SIZE, &zero_sum_result,
+ DMA_PREP_INTERRUPT|DMA_CTRL_ACK);
+
+ cookie = iop_adma_tx_submit(tx);
+ iop_adma_issue_pending(dma_chan);
+ msleep(8);
+
+ if (iop_adma_is_complete(dma_chan, cookie, NULL, NULL) !=
+ DMA_SUCCESS) {
+ dev_err(dev, "Self-test pq-zero-sum timed out, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ if (zero_sum_result != 0) {
+ dev_err(dev, "Self-test pq-zero-sum failed to validate: %x\n",
+ zero_sum_result);
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ /* test incorrect zero sum */
+ i = IOP_ADMA_NUM_SRC_TEST;
+ memset(pq_sw[i] + 100, 0, 100);
+ memset(pq_sw[i+1] + 200, 0, 200);
+ for (i = 0; i < IOP_ADMA_NUM_SRC_TEST + 2; i++)
+ pq_src[i] = dma_map_page(dev, pq[i], 0, PAGE_SIZE,
+ DMA_TO_DEVICE);
+
+ zero_sum_result = 0;
+ tx = iop_adma_prep_dma_pq_val(dma_chan, &pq_src[IOP_ADMA_NUM_SRC_TEST],
+ pq_src, IOP_ADMA_NUM_SRC_TEST,
+ raid6_gfexp, PAGE_SIZE, &zero_sum_result,
+ DMA_PREP_INTERRUPT|DMA_CTRL_ACK);
+
+ cookie = iop_adma_tx_submit(tx);
+ iop_adma_issue_pending(dma_chan);
+ msleep(8);
+
+ if (iop_adma_is_complete(dma_chan, cookie, NULL, NULL) !=
+ DMA_SUCCESS) {
+ dev_err(dev, "Self-test !pq-zero-sum timed out, disabling\n");
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+ if (zero_sum_result != (SUM_CHECK_P_RESULT | SUM_CHECK_Q_RESULT)) {
+ dev_err(dev, "Self-test !pq-zero-sum failed to validate: %x\n",
+ zero_sum_result);
+ err = -ENODEV;
+ goto free_resources;
+ }
+
+free_resources:
+ iop_adma_free_chan_resources(dma_chan);
+out:
+ i = ARRAY_SIZE(pq);
+ while (i--)
+ __free_page(pq[i]);
+ return err;
+}
+#endif
+
static int __devexit iop_adma_remove(struct platform_device *dev)
{
struct iop_adma_device *device = platform_get_drvdata(dev);
dma_dev->max_xor = iop_adma_get_max_xor();
dma_dev->device_prep_dma_xor = iop_adma_prep_dma_xor;
}
- if (dma_has_cap(DMA_ZERO_SUM, dma_dev->cap_mask))
- dma_dev->device_prep_dma_zero_sum =
- iop_adma_prep_dma_zero_sum;
+ if (dma_has_cap(DMA_XOR_VAL, dma_dev->cap_mask))
+ dma_dev->device_prep_dma_xor_val =
+ iop_adma_prep_dma_xor_val;
+ if (dma_has_cap(DMA_PQ, dma_dev->cap_mask)) {
+ dma_set_maxpq(dma_dev, iop_adma_get_max_pq(), 0);
+ dma_dev->device_prep_dma_pq = iop_adma_prep_dma_pq;
+ }
+ if (dma_has_cap(DMA_PQ_VAL, dma_dev->cap_mask))
+ dma_dev->device_prep_dma_pq_val =
+ iop_adma_prep_dma_pq_val;
if (dma_has_cap(DMA_INTERRUPT, dma_dev->cap_mask))
dma_dev->device_prep_dma_interrupt =
iop_adma_prep_dma_interrupt;
}
if (dma_has_cap(DMA_XOR, dma_dev->cap_mask) ||
- dma_has_cap(DMA_MEMSET, dma_dev->cap_mask)) {
- ret = iop_adma_xor_zero_sum_self_test(adev);
+ dma_has_cap(DMA_MEMSET, dma_dev->cap_mask)) {
+ ret = iop_adma_xor_val_self_test(adev);
dev_dbg(&pdev->dev, "xor self test returned %d\n", ret);
if (ret)
goto err_free_iop_chan;
}
+ if (dma_has_cap(DMA_PQ, dma_dev->cap_mask) &&
+ dma_has_cap(DMA_PQ_VAL, dma_dev->cap_mask)) {
+ #ifdef CONFIG_MD_RAID6_PQ
+ ret = iop_adma_pq_zero_sum_self_test(adev);
+ dev_dbg(&pdev->dev, "pq self test returned %d\n", ret);
+ #else
+ /* can not test raid6, so do not publish capability */
+ dma_cap_clear(DMA_PQ, dma_dev->cap_mask);
+ dma_cap_clear(DMA_PQ_VAL, dma_dev->cap_mask);
+ ret = 0;
+ #endif
+ if (ret)
+ goto err_free_iop_chan;
+ }
+
dev_printk(KERN_INFO, &pdev->dev, "Intel(R) IOP: "
- "( %s%s%s%s%s%s%s%s%s%s)\n",
- dma_has_cap(DMA_PQ_XOR, dma_dev->cap_mask) ? "pq_xor " : "",
- dma_has_cap(DMA_PQ_UPDATE, dma_dev->cap_mask) ? "pq_update " : "",
- dma_has_cap(DMA_PQ_ZERO_SUM, dma_dev->cap_mask) ? "pq_zero_sum " : "",
+ "( %s%s%s%s%s%s%s)\n",
+ dma_has_cap(DMA_PQ, dma_dev->cap_mask) ? "pq " : "",
+ dma_has_cap(DMA_PQ_VAL, dma_dev->cap_mask) ? "pq_val " : "",
dma_has_cap(DMA_XOR, dma_dev->cap_mask) ? "xor " : "",
- dma_has_cap(DMA_DUAL_XOR, dma_dev->cap_mask) ? "dual_xor " : "",
- dma_has_cap(DMA_ZERO_SUM, dma_dev->cap_mask) ? "xor_zero_sum " : "",
+ dma_has_cap(DMA_XOR_VAL, dma_dev->cap_mask) ? "xor_val " : "",
dma_has_cap(DMA_MEMSET, dma_dev->cap_mask) ? "fill " : "",
- dma_has_cap(DMA_MEMCPY_CRC32C, dma_dev->cap_mask) ? "cpy+crc " : "",
dma_has_cap(DMA_MEMCPY, dma_dev->cap_mask) ? "cpy " : "",
dma_has_cap(DMA_INTERRUPT, dma_dev->cap_mask) ? "intr " : "");
if (sw_desc) {
grp_start = sw_desc->group_head;
- list_splice_init(&sw_desc->async_tx.tx_list, &iop_chan->chain);
+ list_splice_init(&sw_desc->tx_list, &iop_chan->chain);
async_tx_ack(&sw_desc->async_tx);
iop_desc_init_memcpy(grp_start, 0);
iop_desc_set_byte_count(grp_start, iop_chan, 0);
sw_desc = iop_adma_alloc_slots(iop_chan, slot_cnt, slots_per_op);
if (sw_desc) {
grp_start = sw_desc->group_head;
- list_splice_init(&sw_desc->async_tx.tx_list, &iop_chan->chain);
+ list_splice_init(&sw_desc->tx_list, &iop_chan->chain);
async_tx_ack(&sw_desc->async_tx);
iop_desc_init_null_xor(grp_start, 2, 0);
iop_desc_set_byte_count(grp_start, iop_chan, 0);
iov_byte_offset,
kdata,
copy);
+ /* poll for a descriptor slot */
+ if (unlikely(dma_cookie < 0)) {
+ dma_async_issue_pending(chan);
+ continue;
+ }
len -= copy;
iov[iovec_idx].iov_len -= copy;
page,
offset,
copy);
+ /* poll for a descriptor slot */
+ if (unlikely(dma_cookie < 0)) {
+ dma_async_issue_pending(chan);
+ continue;
+ }
len -= copy;
iov[iovec_idx].iov_len -= copy;
}
alloc_tail->group_head = alloc_start;
alloc_tail->async_tx.cookie = -EBUSY;
- list_splice(&chain, &alloc_tail->async_tx.tx_list);
+ list_splice(&chain, &alloc_tail->tx_list);
mv_chan->last_used = last_used;
mv_desc_clear_next_desc(alloc_start);
mv_desc_clear_next_desc(alloc_tail);
cookie = mv_desc_assign_cookie(mv_chan, sw_desc);
if (list_empty(&mv_chan->chain))
- list_splice_init(&sw_desc->async_tx.tx_list, &mv_chan->chain);
+ list_splice_init(&sw_desc->tx_list, &mv_chan->chain);
else {
new_hw_chain = 0;
old_chain_tail = list_entry(mv_chan->chain.prev,
struct mv_xor_desc_slot,
chain_node);
- list_splice_init(&grp_start->async_tx.tx_list,
+ list_splice_init(&grp_start->tx_list,
&old_chain_tail->chain_node);
if (!mv_can_chain(grp_start))
slot->async_tx.tx_submit = mv_xor_tx_submit;
INIT_LIST_HEAD(&slot->chain_node);
INIT_LIST_HEAD(&slot->slot_node);
+ INIT_LIST_HEAD(&slot->tx_list);
hw_desc = (char *) mv_chan->device->dma_desc_pool;
slot->async_tx.phys =
(dma_addr_t) &hw_desc[idx * MV_XOR_SLOT_SIZE];
* @idx: pool index
* @unmap_src_cnt: number of xor sources
* @unmap_len: transaction bytecount
+ * @tx_list: list of slots that make up a multi-descriptor transaction
* @async_tx: support for the async_tx api
- * @group_list: list of slots that make up a multi-descriptor transaction
- * for example transfer lengths larger than the supported hw max
* @xor_check_result: result of zero sum
* @crc32_result: result crc calculation
*/
u16 unmap_src_cnt;
u32 value;
size_t unmap_len;
+ struct list_head tx_list;
struct dma_async_tx_descriptor async_tx;
union {
u32 *xor_check_result;
--- /dev/null
+/*
+ * Renesas SuperH DMA Engine support
+ *
+ * base is drivers/dma/flsdma.c
+ *
+ * Copyright (C) 2009 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
+ * Copyright (C) 2009 Renesas Solutions, Inc. All rights reserved.
+ * Copyright (C) 2007 Freescale Semiconductor, Inc. All rights reserved.
+ *
+ * This is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * - DMA of SuperH does not have Hardware DMA chain mode.
+ * - MAX DMA size is 16MB.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/dmaengine.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/platform_device.h>
+#include <cpu/dma.h>
+#include <asm/dma-sh.h>
+#include "shdma.h"
+
+/* DMA descriptor control */
+#define DESC_LAST (-1)
+#define DESC_COMP (1)
+#define DESC_NCOMP (0)
+
+#define NR_DESCS_PER_CHANNEL 32
+/*
+ * Define the default configuration for dual address memory-memory transfer.
+ * The 0x400 value represents auto-request, external->external.
+ *
+ * And this driver set 4byte burst mode.
+ * If you want to change mode, you need to change RS_DEFAULT of value.
+ * (ex 1byte burst mode -> (RS_DUAL & ~TS_32)
+ */
+#define RS_DEFAULT (RS_DUAL)
+
+#define SH_DMAC_CHAN_BASE(id) (dma_base_addr[id])
+static void sh_dmae_writel(struct sh_dmae_chan *sh_dc, u32 data, u32 reg)
+{
+ ctrl_outl(data, (SH_DMAC_CHAN_BASE(sh_dc->id) + reg));
+}
+
+static u32 sh_dmae_readl(struct sh_dmae_chan *sh_dc, u32 reg)
+{
+ return ctrl_inl((SH_DMAC_CHAN_BASE(sh_dc->id) + reg));
+}
+
+static void dmae_init(struct sh_dmae_chan *sh_chan)
+{
+ u32 chcr = RS_DEFAULT; /* default is DUAL mode */
+ sh_dmae_writel(sh_chan, chcr, CHCR);
+}
+
+/*
+ * Reset DMA controller
+ *
+ * SH7780 has two DMAOR register
+ */
+static void sh_dmae_ctl_stop(int id)
+{
+ unsigned short dmaor = dmaor_read_reg(id);
+
+ dmaor &= ~(DMAOR_NMIF | DMAOR_AE);
+ dmaor_write_reg(id, dmaor);
+}
+
+static int sh_dmae_rst(int id)
+{
+ unsigned short dmaor;
+
+ sh_dmae_ctl_stop(id);
+ dmaor = (dmaor_read_reg(id)|DMAOR_INIT);
+
+ dmaor_write_reg(id, dmaor);
+ if ((dmaor_read_reg(id) & (DMAOR_AE | DMAOR_NMIF))) {
+ pr_warning(KERN_ERR "dma-sh: Can't initialize DMAOR.\n");
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int dmae_is_idle(struct sh_dmae_chan *sh_chan)
+{
+ u32 chcr = sh_dmae_readl(sh_chan, CHCR);
+ if (chcr & CHCR_DE) {
+ if (!(chcr & CHCR_TE))
+ return -EBUSY; /* working */
+ }
+ return 0; /* waiting */
+}
+
+static inline unsigned int calc_xmit_shift(struct sh_dmae_chan *sh_chan)
+{
+ u32 chcr = sh_dmae_readl(sh_chan, CHCR);
+ return ts_shift[(chcr & CHCR_TS_MASK) >> CHCR_TS_SHIFT];
+}
+
+static void dmae_set_reg(struct sh_dmae_chan *sh_chan, struct sh_dmae_regs hw)
+{
+ sh_dmae_writel(sh_chan, hw.sar, SAR);
+ sh_dmae_writel(sh_chan, hw.dar, DAR);
+ sh_dmae_writel(sh_chan,
+ (hw.tcr >> calc_xmit_shift(sh_chan)), TCR);
+}
+
+static void dmae_start(struct sh_dmae_chan *sh_chan)
+{
+ u32 chcr = sh_dmae_readl(sh_chan, CHCR);
+
+ chcr |= (CHCR_DE|CHCR_IE);
+ sh_dmae_writel(sh_chan, chcr, CHCR);
+}
+
+static void dmae_halt(struct sh_dmae_chan *sh_chan)
+{
+ u32 chcr = sh_dmae_readl(sh_chan, CHCR);
+
+ chcr &= ~(CHCR_DE | CHCR_TE | CHCR_IE);
+ sh_dmae_writel(sh_chan, chcr, CHCR);
+}
+
+static int dmae_set_chcr(struct sh_dmae_chan *sh_chan, u32 val)
+{
+ int ret = dmae_is_idle(sh_chan);
+ /* When DMA was working, can not set data to CHCR */
+ if (ret)
+ return ret;
+
+ sh_dmae_writel(sh_chan, val, CHCR);
+ return 0;
+}
+
+#define DMARS1_ADDR 0x04
+#define DMARS2_ADDR 0x08
+#define DMARS_SHIFT 8
+#define DMARS_CHAN_MSK 0x01
+static int dmae_set_dmars(struct sh_dmae_chan *sh_chan, u16 val)
+{
+ u32 addr;
+ int shift = 0;
+ int ret = dmae_is_idle(sh_chan);
+ if (ret)
+ return ret;
+
+ if (sh_chan->id & DMARS_CHAN_MSK)
+ shift = DMARS_SHIFT;
+
+ switch (sh_chan->id) {
+ /* DMARS0 */
+ case 0:
+ case 1:
+ addr = SH_DMARS_BASE;
+ break;
+ /* DMARS1 */
+ case 2:
+ case 3:
+ addr = (SH_DMARS_BASE + DMARS1_ADDR);
+ break;
+ /* DMARS2 */
+ case 4:
+ case 5:
+ addr = (SH_DMARS_BASE + DMARS2_ADDR);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ctrl_outw((val << shift) |
+ (ctrl_inw(addr) & (shift ? 0xFF00 : 0x00FF)),
+ addr);
+
+ return 0;
+}
+
+static dma_cookie_t sh_dmae_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+ struct sh_desc *desc = tx_to_sh_desc(tx);
+ struct sh_dmae_chan *sh_chan = to_sh_chan(tx->chan);
+ dma_cookie_t cookie;
+
+ spin_lock_bh(&sh_chan->desc_lock);
+
+ cookie = sh_chan->common.cookie;
+ cookie++;
+ if (cookie < 0)
+ cookie = 1;
+
+ /* If desc only in the case of 1 */
+ if (desc->async_tx.cookie != -EBUSY)
+ desc->async_tx.cookie = cookie;
+ sh_chan->common.cookie = desc->async_tx.cookie;
+
+ list_splice_init(&desc->tx_list, sh_chan->ld_queue.prev);
+
+ spin_unlock_bh(&sh_chan->desc_lock);
+
+ return cookie;
+}
+
+static struct sh_desc *sh_dmae_get_desc(struct sh_dmae_chan *sh_chan)
+{
+ struct sh_desc *desc, *_desc, *ret = NULL;
+
+ spin_lock_bh(&sh_chan->desc_lock);
+ list_for_each_entry_safe(desc, _desc, &sh_chan->ld_free, node) {
+ if (async_tx_test_ack(&desc->async_tx)) {
+ list_del(&desc->node);
+ ret = desc;
+ break;
+ }
+ }
+ spin_unlock_bh(&sh_chan->desc_lock);
+
+ return ret;
+}
+
+static void sh_dmae_put_desc(struct sh_dmae_chan *sh_chan, struct sh_desc *desc)
+{
+ if (desc) {
+ spin_lock_bh(&sh_chan->desc_lock);
+
+ list_splice_init(&desc->tx_list, &sh_chan->ld_free);
+ list_add(&desc->node, &sh_chan->ld_free);
+
+ spin_unlock_bh(&sh_chan->desc_lock);
+ }
+}
+
+static int sh_dmae_alloc_chan_resources(struct dma_chan *chan)
+{
+ struct sh_dmae_chan *sh_chan = to_sh_chan(chan);
+ struct sh_desc *desc;
+
+ spin_lock_bh(&sh_chan->desc_lock);
+ while (sh_chan->descs_allocated < NR_DESCS_PER_CHANNEL) {
+ spin_unlock_bh(&sh_chan->desc_lock);
+ desc = kzalloc(sizeof(struct sh_desc), GFP_KERNEL);
+ if (!desc) {
+ spin_lock_bh(&sh_chan->desc_lock);
+ break;
+ }
+ dma_async_tx_descriptor_init(&desc->async_tx,
+ &sh_chan->common);
+ desc->async_tx.tx_submit = sh_dmae_tx_submit;
+ desc->async_tx.flags = DMA_CTRL_ACK;
+ INIT_LIST_HEAD(&desc->tx_list);
+ sh_dmae_put_desc(sh_chan, desc);
+
+ spin_lock_bh(&sh_chan->desc_lock);
+ sh_chan->descs_allocated++;
+ }
+ spin_unlock_bh(&sh_chan->desc_lock);
+
+ return sh_chan->descs_allocated;
+}
+
+/*
+ * sh_dma_free_chan_resources - Free all resources of the channel.
+ */
+static void sh_dmae_free_chan_resources(struct dma_chan *chan)
+{
+ struct sh_dmae_chan *sh_chan = to_sh_chan(chan);
+ struct sh_desc *desc, *_desc;
+ LIST_HEAD(list);
+
+ BUG_ON(!list_empty(&sh_chan->ld_queue));
+ spin_lock_bh(&sh_chan->desc_lock);
+
+ list_splice_init(&sh_chan->ld_free, &list);
+ sh_chan->descs_allocated = 0;
+
+ spin_unlock_bh(&sh_chan->desc_lock);
+
+ list_for_each_entry_safe(desc, _desc, &list, node)
+ kfree(desc);
+}
+
+static struct dma_async_tx_descriptor *sh_dmae_prep_memcpy(
+ struct dma_chan *chan, dma_addr_t dma_dest, dma_addr_t dma_src,
+ size_t len, unsigned long flags)
+{
+ struct sh_dmae_chan *sh_chan;
+ struct sh_desc *first = NULL, *prev = NULL, *new;
+ size_t copy_size;
+
+ if (!chan)
+ return NULL;
+
+ if (!len)
+ return NULL;
+
+ sh_chan = to_sh_chan(chan);
+
+ do {
+ /* Allocate the link descriptor from DMA pool */
+ new = sh_dmae_get_desc(sh_chan);
+ if (!new) {
+ dev_err(sh_chan->dev,
+ "No free memory for link descriptor\n");
+ goto err_get_desc;
+ }
+
+ copy_size = min(len, (size_t)SH_DMA_TCR_MAX);
+
+ new->hw.sar = dma_src;
+ new->hw.dar = dma_dest;
+ new->hw.tcr = copy_size;
+ if (!first)
+ first = new;
+
+ new->mark = DESC_NCOMP;
+ async_tx_ack(&new->async_tx);
+
+ prev = new;
+ len -= copy_size;
+ dma_src += copy_size;
+ dma_dest += copy_size;
+ /* Insert the link descriptor to the LD ring */
+ list_add_tail(&new->node, &first->tx_list);
+ } while (len);
+
+ new->async_tx.flags = flags; /* client is in control of this ack */
+ new->async_tx.cookie = -EBUSY; /* Last desc */
+
+ return &first->async_tx;
+
+err_get_desc:
+ sh_dmae_put_desc(sh_chan, first);
+ return NULL;
+
+}
+
+/*
+ * sh_chan_ld_cleanup - Clean up link descriptors
+ *
+ * This function clean up the ld_queue of DMA channel.
+ */
+static void sh_dmae_chan_ld_cleanup(struct sh_dmae_chan *sh_chan)
+{
+ struct sh_desc *desc, *_desc;
+
+ spin_lock_bh(&sh_chan->desc_lock);
+ list_for_each_entry_safe(desc, _desc, &sh_chan->ld_queue, node) {
+ dma_async_tx_callback callback;
+ void *callback_param;
+
+ /* non send data */
+ if (desc->mark == DESC_NCOMP)
+ break;
+
+ /* send data sesc */
+ callback = desc->async_tx.callback;
+ callback_param = desc->async_tx.callback_param;
+
+ /* Remove from ld_queue list */
+ list_splice_init(&desc->tx_list, &sh_chan->ld_free);
+
+ dev_dbg(sh_chan->dev, "link descriptor %p will be recycle.\n",
+ desc);
+
+ list_move(&desc->node, &sh_chan->ld_free);
+ /* Run the link descriptor callback function */
+ if (callback) {
+ spin_unlock_bh(&sh_chan->desc_lock);
+ dev_dbg(sh_chan->dev, "link descriptor %p callback\n",
+ desc);
+ callback(callback_param);
+ spin_lock_bh(&sh_chan->desc_lock);
+ }
+ }
+ spin_unlock_bh(&sh_chan->desc_lock);
+}
+
+static void sh_chan_xfer_ld_queue(struct sh_dmae_chan *sh_chan)
+{
+ struct list_head *ld_node;
+ struct sh_dmae_regs hw;
+
+ /* DMA work check */
+ if (dmae_is_idle(sh_chan))
+ return;
+
+ /* Find the first un-transfer desciptor */
+ for (ld_node = sh_chan->ld_queue.next;
+ (ld_node != &sh_chan->ld_queue)
+ && (to_sh_desc(ld_node)->mark == DESC_COMP);
+ ld_node = ld_node->next)
+ cpu_relax();
+
+ if (ld_node != &sh_chan->ld_queue) {
+ /* Get the ld start address from ld_queue */
+ hw = to_sh_desc(ld_node)->hw;
+ dmae_set_reg(sh_chan, hw);
+ dmae_start(sh_chan);
+ }
+}
+
+static void sh_dmae_memcpy_issue_pending(struct dma_chan *chan)
+{
+ struct sh_dmae_chan *sh_chan = to_sh_chan(chan);
+ sh_chan_xfer_ld_queue(sh_chan);
+}
+
+static enum dma_status sh_dmae_is_complete(struct dma_chan *chan,
+ dma_cookie_t cookie,
+ dma_cookie_t *done,
+ dma_cookie_t *used)
+{
+ struct sh_dmae_chan *sh_chan = to_sh_chan(chan);
+ dma_cookie_t last_used;
+ dma_cookie_t last_complete;
+
+ sh_dmae_chan_ld_cleanup(sh_chan);
+
+ last_used = chan->cookie;
+ last_complete = sh_chan->completed_cookie;
+ if (last_complete == -EBUSY)
+ last_complete = last_used;
+
+ if (done)
+ *done = last_complete;
+
+ if (used)
+ *used = last_used;
+
+ return dma_async_is_complete(cookie, last_complete, last_used);
+}
+
+static irqreturn_t sh_dmae_interrupt(int irq, void *data)
+{
+ irqreturn_t ret = IRQ_NONE;
+ struct sh_dmae_chan *sh_chan = (struct sh_dmae_chan *)data;
+ u32 chcr = sh_dmae_readl(sh_chan, CHCR);
+
+ if (chcr & CHCR_TE) {
+ /* DMA stop */
+ dmae_halt(sh_chan);
+
+ ret = IRQ_HANDLED;
+ tasklet_schedule(&sh_chan->tasklet);
+ }
+
+ return ret;
+}
+
+#if defined(CONFIG_CPU_SH4)
+static irqreturn_t sh_dmae_err(int irq, void *data)
+{
+ int err = 0;
+ struct sh_dmae_device *shdev = (struct sh_dmae_device *)data;
+
+ /* IRQ Multi */
+ if (shdev->pdata.mode & SHDMA_MIX_IRQ) {
+ int cnt = 0;
+ switch (irq) {
+#if defined(DMTE6_IRQ) && defined(DMAE1_IRQ)
+ case DMTE6_IRQ:
+ cnt++;
+#endif
+ case DMTE0_IRQ:
+ if (dmaor_read_reg(cnt) & (DMAOR_NMIF | DMAOR_AE)) {
+ disable_irq(irq);
+ return IRQ_HANDLED;
+ }
+ default:
+ return IRQ_NONE;
+ }
+ } else {
+ /* reset dma controller */
+ err = sh_dmae_rst(0);
+ if (err)
+ return err;
+ if (shdev->pdata.mode & SHDMA_DMAOR1) {
+ err = sh_dmae_rst(1);
+ if (err)
+ return err;
+ }
+ disable_irq(irq);
+ return IRQ_HANDLED;
+ }
+}
+#endif
+
+static void dmae_do_tasklet(unsigned long data)
+{
+ struct sh_dmae_chan *sh_chan = (struct sh_dmae_chan *)data;
+ struct sh_desc *desc, *_desc, *cur_desc = NULL;
+ u32 sar_buf = sh_dmae_readl(sh_chan, SAR);
+ list_for_each_entry_safe(desc, _desc,
+ &sh_chan->ld_queue, node) {
+ if ((desc->hw.sar + desc->hw.tcr) == sar_buf) {
+ cur_desc = desc;
+ break;
+ }
+ }
+
+ if (cur_desc) {
+ switch (cur_desc->async_tx.cookie) {
+ case 0: /* other desc data */
+ break;
+ case -EBUSY: /* last desc */
+ sh_chan->completed_cookie =
+ cur_desc->async_tx.cookie;
+ break;
+ default: /* first desc ( 0 < )*/
+ sh_chan->completed_cookie =
+ cur_desc->async_tx.cookie - 1;
+ break;
+ }
+ cur_desc->mark = DESC_COMP;
+ }
+ /* Next desc */
+ sh_chan_xfer_ld_queue(sh_chan);
+ sh_dmae_chan_ld_cleanup(sh_chan);
+}
+
+static unsigned int get_dmae_irq(unsigned int id)
+{
+ unsigned int irq = 0;
+ if (id < ARRAY_SIZE(dmte_irq_map))
+ irq = dmte_irq_map[id];
+ return irq;
+}
+
+static int __devinit sh_dmae_chan_probe(struct sh_dmae_device *shdev, int id)
+{
+ int err;
+ unsigned int irq = get_dmae_irq(id);
+ unsigned long irqflags = IRQF_DISABLED;
+ struct sh_dmae_chan *new_sh_chan;
+
+ /* alloc channel */
+ new_sh_chan = kzalloc(sizeof(struct sh_dmae_chan), GFP_KERNEL);
+ if (!new_sh_chan) {
+ dev_err(shdev->common.dev, "No free memory for allocating "
+ "dma channels!\n");
+ return -ENOMEM;
+ }
+
+ new_sh_chan->dev = shdev->common.dev;
+ new_sh_chan->id = id;
+
+ /* Init DMA tasklet */
+ tasklet_init(&new_sh_chan->tasklet, dmae_do_tasklet,
+ (unsigned long)new_sh_chan);
+
+ /* Init the channel */
+ dmae_init(new_sh_chan);
+
+ spin_lock_init(&new_sh_chan->desc_lock);
+
+ /* Init descripter manage list */
+ INIT_LIST_HEAD(&new_sh_chan->ld_queue);
+ INIT_LIST_HEAD(&new_sh_chan->ld_free);
+
+ /* copy struct dma_device */
+ new_sh_chan->common.device = &shdev->common;
+
+ /* Add the channel to DMA device channel list */
+ list_add_tail(&new_sh_chan->common.device_node,
+ &shdev->common.channels);
+ shdev->common.chancnt++;
+
+ if (shdev->pdata.mode & SHDMA_MIX_IRQ) {
+ irqflags = IRQF_SHARED;
+#if defined(DMTE6_IRQ)
+ if (irq >= DMTE6_IRQ)
+ irq = DMTE6_IRQ;
+ else
+#endif
+ irq = DMTE0_IRQ;
+ }
+
+ snprintf(new_sh_chan->dev_id, sizeof(new_sh_chan->dev_id),
+ "sh-dmae%d", new_sh_chan->id);
+
+ /* set up channel irq */
+ err = request_irq(irq, &sh_dmae_interrupt,
+ irqflags, new_sh_chan->dev_id, new_sh_chan);
+ if (err) {
+ dev_err(shdev->common.dev, "DMA channel %d request_irq error "
+ "with return %d\n", id, err);
+ goto err_no_irq;
+ }
+
+ /* CHCR register control function */
+ new_sh_chan->set_chcr = dmae_set_chcr;
+ /* DMARS register control function */
+ new_sh_chan->set_dmars = dmae_set_dmars;
+
+ shdev->chan[id] = new_sh_chan;
+ return 0;
+
+err_no_irq:
+ /* remove from dmaengine device node */
+ list_del(&new_sh_chan->common.device_node);
+ kfree(new_sh_chan);
+ return err;
+}
+
+static void sh_dmae_chan_remove(struct sh_dmae_device *shdev)
+{
+ int i;
+
+ for (i = shdev->common.chancnt - 1 ; i >= 0 ; i--) {
+ if (shdev->chan[i]) {
+ struct sh_dmae_chan *shchan = shdev->chan[i];
+ if (!(shdev->pdata.mode & SHDMA_MIX_IRQ))
+ free_irq(dmte_irq_map[i], shchan);
+
+ list_del(&shchan->common.device_node);
+ kfree(shchan);
+ shdev->chan[i] = NULL;
+ }
+ }
+ shdev->common.chancnt = 0;
+}
+
+static int __init sh_dmae_probe(struct platform_device *pdev)
+{
+ int err = 0, cnt, ecnt;
+ unsigned long irqflags = IRQF_DISABLED;
+#if defined(CONFIG_CPU_SH4)
+ int eirq[] = { DMAE0_IRQ,
+#if defined(DMAE1_IRQ)
+ DMAE1_IRQ
+#endif
+ };
+#endif
+ struct sh_dmae_device *shdev;
+
+ shdev = kzalloc(sizeof(struct sh_dmae_device), GFP_KERNEL);
+ if (!shdev) {
+ dev_err(&pdev->dev, "No enough memory\n");
+ err = -ENOMEM;
+ goto shdev_err;
+ }
+
+ /* get platform data */
+ if (!pdev->dev.platform_data)
+ goto shdev_err;
+
+ /* platform data */
+ memcpy(&shdev->pdata, pdev->dev.platform_data,
+ sizeof(struct sh_dmae_pdata));
+
+ /* reset dma controller */
+ err = sh_dmae_rst(0);
+ if (err)
+ goto rst_err;
+
+ /* SH7780/85/23 has DMAOR1 */
+ if (shdev->pdata.mode & SHDMA_DMAOR1) {
+ err = sh_dmae_rst(1);
+ if (err)
+ goto rst_err;
+ }
+
+ INIT_LIST_HEAD(&shdev->common.channels);
+
+ dma_cap_set(DMA_MEMCPY, shdev->common.cap_mask);
+ shdev->common.device_alloc_chan_resources
+ = sh_dmae_alloc_chan_resources;
+ shdev->common.device_free_chan_resources = sh_dmae_free_chan_resources;
+ shdev->common.device_prep_dma_memcpy = sh_dmae_prep_memcpy;
+ shdev->common.device_is_tx_complete = sh_dmae_is_complete;
+ shdev->common.device_issue_pending = sh_dmae_memcpy_issue_pending;
+ shdev->common.dev = &pdev->dev;
+
+#if defined(CONFIG_CPU_SH4)
+ /* Non Mix IRQ mode SH7722/SH7730 etc... */
+ if (shdev->pdata.mode & SHDMA_MIX_IRQ) {
+ irqflags = IRQF_SHARED;
+ eirq[0] = DMTE0_IRQ;
+#if defined(DMTE6_IRQ) && defined(DMAE1_IRQ)
+ eirq[1] = DMTE6_IRQ;
+#endif
+ }
+
+ for (ecnt = 0 ; ecnt < ARRAY_SIZE(eirq); ecnt++) {
+ err = request_irq(eirq[ecnt], sh_dmae_err,
+ irqflags, "DMAC Address Error", shdev);
+ if (err) {
+ dev_err(&pdev->dev, "DMA device request_irq"
+ "error (irq %d) with return %d\n",
+ eirq[ecnt], err);
+ goto eirq_err;
+ }
+ }
+#endif /* CONFIG_CPU_SH4 */
+
+ /* Create DMA Channel */
+ for (cnt = 0 ; cnt < MAX_DMA_CHANNELS ; cnt++) {
+ err = sh_dmae_chan_probe(shdev, cnt);
+ if (err)
+ goto chan_probe_err;
+ }
+
+ platform_set_drvdata(pdev, shdev);
+ dma_async_device_register(&shdev->common);
+
+ return err;
+
+chan_probe_err:
+ sh_dmae_chan_remove(shdev);
+
+eirq_err:
+ for (ecnt-- ; ecnt >= 0; ecnt--)
+ free_irq(eirq[ecnt], shdev);
+
+rst_err:
+ kfree(shdev);
+
+shdev_err:
+ return err;
+}
+
+static int __exit sh_dmae_remove(struct platform_device *pdev)
+{
+ struct sh_dmae_device *shdev = platform_get_drvdata(pdev);
+
+ dma_async_device_unregister(&shdev->common);
+
+ if (shdev->pdata.mode & SHDMA_MIX_IRQ) {
+ free_irq(DMTE0_IRQ, shdev);
+#if defined(DMTE6_IRQ)
+ free_irq(DMTE6_IRQ, shdev);
+#endif
+ }
+
+ /* channel data remove */
+ sh_dmae_chan_remove(shdev);
+
+ if (!(shdev->pdata.mode & SHDMA_MIX_IRQ)) {
+ free_irq(DMAE0_IRQ, shdev);
+#if defined(DMAE1_IRQ)
+ free_irq(DMAE1_IRQ, shdev);
+#endif
+ }
+ kfree(shdev);
+
+ return 0;
+}
+
+static void sh_dmae_shutdown(struct platform_device *pdev)
+{
+ struct sh_dmae_device *shdev = platform_get_drvdata(pdev);
+ sh_dmae_ctl_stop(0);
+ if (shdev->pdata.mode & SHDMA_DMAOR1)
+ sh_dmae_ctl_stop(1);
+}
+
+static struct platform_driver sh_dmae_driver = {
+ .remove = __exit_p(sh_dmae_remove),
+ .shutdown = sh_dmae_shutdown,
+ .driver = {
+ .name = "sh-dma-engine",
+ },
+};
+
+static int __init sh_dmae_init(void)
+{
+ return platform_driver_probe(&sh_dmae_driver, sh_dmae_probe);
+}
+module_init(sh_dmae_init);
+
+static void __exit sh_dmae_exit(void)
+{
+ platform_driver_unregister(&sh_dmae_driver);
+}
+module_exit(sh_dmae_exit);
+
+MODULE_AUTHOR("Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>");
+MODULE_DESCRIPTION("Renesas SH DMA Engine driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * Renesas SuperH DMA Engine support
+ *
+ * Copyright (C) 2009 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
+ * Copyright (C) 2009 Renesas Solutions, Inc. All rights reserved.
+ *
+ * This is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ */
+#ifndef __DMA_SHDMA_H
+#define __DMA_SHDMA_H
+
+#include <linux/device.h>
+#include <linux/dmapool.h>
+#include <linux/dmaengine.h>
+
+#define SH_DMA_TCR_MAX 0x00FFFFFF /* 16MB */
+
+struct sh_dmae_regs {
+ u32 sar; /* SAR / source address */
+ u32 dar; /* DAR / destination address */
+ u32 tcr; /* TCR / transfer count */
+};
+
+struct sh_desc {
+ struct list_head tx_list;
+ struct sh_dmae_regs hw;
+ struct list_head node;
+ struct dma_async_tx_descriptor async_tx;
+ int mark;
+};
+
+struct sh_dmae_chan {
+ dma_cookie_t completed_cookie; /* The maximum cookie completed */
+ spinlock_t desc_lock; /* Descriptor operation lock */
+ struct list_head ld_queue; /* Link descriptors queue */
+ struct list_head ld_free; /* Link descriptors free */
+ struct dma_chan common; /* DMA common channel */
+ struct device *dev; /* Channel device */
+ struct tasklet_struct tasklet; /* Tasklet */
+ int descs_allocated; /* desc count */
+ int id; /* Raw id of this channel */
+ char dev_id[16]; /* unique name per DMAC of channel */
+
+ /* Set chcr */
+ int (*set_chcr)(struct sh_dmae_chan *sh_chan, u32 regs);
+ /* Set DMA resource */
+ int (*set_dmars)(struct sh_dmae_chan *sh_chan, u16 res);
+};
+
+struct sh_dmae_device {
+ struct dma_device common;
+ struct sh_dmae_chan *chan[MAX_DMA_CHANNELS];
+ struct sh_dmae_pdata pdata;
+};
+
+#define to_sh_chan(chan) container_of(chan, struct sh_dmae_chan, common)
+#define to_sh_desc(lh) container_of(lh, struct sh_desc, node)
+#define tx_to_sh_desc(tx) container_of(tx, struct sh_desc, async_tx)
+
+#endif /* __DMA_SHDMA_H */
static struct txx9dmac_desc *txx9dmac_last_child(struct txx9dmac_desc *desc)
{
- if (!list_empty(&desc->txd.tx_list))
- desc = list_entry(desc->txd.tx_list.prev,
- struct txx9dmac_desc, desc_node);
+ if (!list_empty(&desc->tx_list))
+ desc = list_entry(desc->tx_list.prev, typeof(*desc), desc_node);
return desc;
}
desc = kzalloc(sizeof(*desc), flags);
if (!desc)
return NULL;
+ INIT_LIST_HEAD(&desc->tx_list);
dma_async_tx_descriptor_init(&desc->txd, &dc->chan);
desc->txd.tx_submit = txx9dmac_tx_submit;
/* txd.flags will be overwritten in prep funcs */
struct txx9dmac_dev *ddev = dc->ddev;
struct txx9dmac_desc *child;
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
dma_sync_single_for_cpu(chan2parent(&dc->chan),
child->txd.phys, ddev->descsize,
DMA_TO_DEVICE);
txx9dmac_sync_desc_for_cpu(dc, desc);
spin_lock_bh(&dc->lock);
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
dev_vdbg(chan2dev(&dc->chan),
"moving child desc %p to freelist\n",
child);
- list_splice_init(&desc->txd.tx_list, &dc->free_list);
+ list_splice_init(&desc->tx_list, &dc->free_list);
dev_vdbg(chan2dev(&dc->chan), "moving desc %p to freelist\n",
desc);
list_add(&desc->desc_node, &dc->free_list);
param = txd->callback_param;
txx9dmac_sync_desc_for_cpu(dc, desc);
- list_splice_init(&txd->tx_list, &dc->free_list);
+ list_splice_init(&desc->tx_list, &dc->free_list);
list_move(&desc->desc_node, &dc->free_list);
if (!ds) {
"Bad descriptor submitted for DMA! (cookie: %d)\n",
bad_desc->txd.cookie);
txx9dmac_dump_desc(dc, &bad_desc->hwdesc);
- list_for_each_entry(child, &bad_desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &bad_desc->tx_list, desc_node)
txx9dmac_dump_desc(dc, &child->hwdesc);
/* Pretend the descriptor completed successfully */
txx9dmac_descriptor_complete(dc, bad_desc);
return;
}
- list_for_each_entry(child, &desc->txd.tx_list, desc_node)
+ list_for_each_entry(child, &desc->tx_list, desc_node)
if (desc_read_CHAR(dc, child) == chain) {
/* Currently in progress */
if (csr & TXX9_DMA_CSR_ABCHC)
dma_sync_single_for_device(chan2parent(&dc->chan),
prev->txd.phys, ddev->descsize,
DMA_TO_DEVICE);
- list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ list_add_tail(&desc->desc_node, &first->tx_list);
}
prev = desc;
}
prev->txd.phys,
ddev->descsize,
DMA_TO_DEVICE);
- list_add_tail(&desc->desc_node,
- &first->txd.tx_list);
+ list_add_tail(&desc->desc_node, &first->tx_list);
}
prev = desc;
}
/* THEN values for driver housekeeping */
struct list_head desc_node ____cacheline_aligned;
+ struct list_head tx_list;
struct dma_async_tx_descriptor txd;
size_t len;
};
Support for error detection and correction on the Intel
3000 and 3010 server chipsets.
+config EDAC_I3200
+ tristate "Intel 3200"
+ depends on EDAC_MM_EDAC && PCI && X86 && EXPERIMENTAL
+ help
+ Support for error detection and correction on the Intel
+ 3200 and 3210 server chipsets.
+
config EDAC_X38
tristate "Intel X38"
depends on EDAC_MM_EDAC && PCI && X86
San Clemente MCH.
config EDAC_MPC85XX
- tristate "Freescale MPC85xx"
- depends on EDAC_MM_EDAC && FSL_SOC && MPC85xx
+ tristate "Freescale MPC83xx / MPC85xx"
+ depends on EDAC_MM_EDAC && FSL_SOC && (PPC_83xx || MPC85xx)
help
Support for error detection and correction on the Freescale
- MPC8560, MPC8540, MPC8548
+ MPC8349, MPC8560, MPC8540, MPC8548
config EDAC_MV64X60
tristate "Marvell MV64x60"
obj-$(CONFIG_EDAC_I82875P) += i82875p_edac.o
obj-$(CONFIG_EDAC_I82975X) += i82975x_edac.o
obj-$(CONFIG_EDAC_I3000) += i3000_edac.o
+obj-$(CONFIG_EDAC_I3200) += i3200_edac.o
obj-$(CONFIG_EDAC_X38) += x38_edac.o
obj-$(CONFIG_EDAC_I82860) += i82860_edac.o
obj-$(CONFIG_EDAC_R82600) += r82600_edac.o
obj-$(CONFIG_EDAC_PPC4XX) += ppc4xx_edac.o
obj-$(CONFIG_EDAC_AMD8111) += amd8111_edac.o
obj-$(CONFIG_EDAC_AMD8131) += amd8131_edac.o
+
if (!devm_request_mem_region(&pdev->dev,
r->start,
- r->end - r->start + 1,
+ resource_size(r),
pdev->name)) {
cpc925_printk(KERN_ERR, "Unable to request mem region\n");
res = -EBUSY;
goto err1;
}
- vbase = devm_ioremap(&pdev->dev, r->start, r->end - r->start + 1);
+ vbase = devm_ioremap(&pdev->dev, r->start, resource_size(r));
if (!vbase) {
cpc925_printk(KERN_ERR, "Unable to ioremap device\n");
res = -ENOMEM;
cpc925_mc_exit(mci);
edac_mc_free(mci);
err2:
- devm_release_mem_region(&pdev->dev, r->start, r->end-r->start+1);
+ devm_release_mem_region(&pdev->dev, r->start, resource_size(r));
err1:
devres_release_group(&pdev->dev, cpc925_probe);
out:
edac_dev = container_of(head, struct edac_device_ctl_info, rcu);
INIT_LIST_HEAD(&edac_dev->link);
- complete(&edac_dev->removal_complete);
}
/*
*edac_device)
{
list_del_rcu(&edac_device->link);
-
- init_completion(&edac_device->removal_complete);
call_rcu(&edac_device->rcu, complete_edac_device_list_del);
- wait_for_completion(&edac_device->removal_complete);
+ rcu_barrier();
}
/*
mci = container_of(head, struct mem_ctl_info, rcu);
INIT_LIST_HEAD(&mci->link);
- complete(&mci->complete);
}
static void del_mc_from_global_list(struct mem_ctl_info *mci)
{
atomic_dec(&edac_handlers);
list_del_rcu(&mci->link);
- init_completion(&mci->complete);
call_rcu(&mci->rcu, complete_mc_list_del);
- wait_for_completion(&mci->complete);
+ rcu_barrier();
}
/**
pci = container_of(head, struct edac_pci_ctl_info, rcu);
INIT_LIST_HEAD(&pci->link);
- complete(&pci->complete);
}
/*
static void del_edac_pci_from_global_list(struct edac_pci_ctl_info *pci)
{
list_del_rcu(&pci->link);
- init_completion(&pci->complete);
call_rcu(&pci->rcu, complete_edac_pci_list_del);
- wait_for_completion(&pci->complete);
+ rcu_barrier();
}
#if 0
--- /dev/null
+/*
+ * Intel 3200/3210 Memory Controller kernel module
+ * Copyright (C) 2008-2009 Akamai Technologies, Inc.
+ * Portions by Hitoshi Mitake <h.mitake@gmail.com>.
+ *
+ * This file may be distributed under the terms of the
+ * GNU General Public License.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/slab.h>
+#include <linux/edac.h>
+#include <linux/io.h>
+#include "edac_core.h"
+
+#define I3200_REVISION "1.1"
+
+#define EDAC_MOD_STR "i3200_edac"
+
+#define PCI_DEVICE_ID_INTEL_3200_HB 0x29f0
+
+#define I3200_RANKS 8
+#define I3200_RANKS_PER_CHANNEL 4
+#define I3200_CHANNELS 2
+
+/* Intel 3200 register addresses - device 0 function 0 - DRAM Controller */
+
+#define I3200_MCHBAR_LOW 0x48 /* MCH Memory Mapped Register BAR */
+#define I3200_MCHBAR_HIGH 0x4c
+#define I3200_MCHBAR_MASK 0xfffffc000ULL /* bits 35:14 */
+#define I3200_MMR_WINDOW_SIZE 16384
+
+#define I3200_TOM 0xa0 /* Top of Memory (16b)
+ *
+ * 15:10 reserved
+ * 9:0 total populated physical memory
+ */
+#define I3200_TOM_MASK 0x3ff /* bits 9:0 */
+#define I3200_TOM_SHIFT 26 /* 64MiB grain */
+
+#define I3200_ERRSTS 0xc8 /* Error Status Register (16b)
+ *
+ * 15 reserved
+ * 14 Isochronous TBWRR Run Behind FIFO Full
+ * (ITCV)
+ * 13 Isochronous TBWRR Run Behind FIFO Put
+ * (ITSTV)
+ * 12 reserved
+ * 11 MCH Thermal Sensor Event
+ * for SMI/SCI/SERR (GTSE)
+ * 10 reserved
+ * 9 LOCK to non-DRAM Memory Flag (LCKF)
+ * 8 reserved
+ * 7 DRAM Throttle Flag (DTF)
+ * 6:2 reserved
+ * 1 Multi-bit DRAM ECC Error Flag (DMERR)
+ * 0 Single-bit DRAM ECC Error Flag (DSERR)
+ */
+#define I3200_ERRSTS_UE 0x0002
+#define I3200_ERRSTS_CE 0x0001
+#define I3200_ERRSTS_BITS (I3200_ERRSTS_UE | I3200_ERRSTS_CE)
+
+
+/* Intel MMIO register space - device 0 function 0 - MMR space */
+
+#define I3200_C0DRB 0x200 /* Channel 0 DRAM Rank Boundary (16b x 4)
+ *
+ * 15:10 reserved
+ * 9:0 Channel 0 DRAM Rank Boundary Address
+ */
+#define I3200_C1DRB 0x600 /* Channel 1 DRAM Rank Boundary (16b x 4) */
+#define I3200_DRB_MASK 0x3ff /* bits 9:0 */
+#define I3200_DRB_SHIFT 26 /* 64MiB grain */
+
+#define I3200_C0ECCERRLOG 0x280 /* Channel 0 ECC Error Log (64b)
+ *
+ * 63:48 Error Column Address (ERRCOL)
+ * 47:32 Error Row Address (ERRROW)
+ * 31:29 Error Bank Address (ERRBANK)
+ * 28:27 Error Rank Address (ERRRANK)
+ * 26:24 reserved
+ * 23:16 Error Syndrome (ERRSYND)
+ * 15: 2 reserved
+ * 1 Multiple Bit Error Status (MERRSTS)
+ * 0 Correctable Error Status (CERRSTS)
+ */
+#define I3200_C1ECCERRLOG 0x680 /* Chan 1 ECC Error Log (64b) */
+#define I3200_ECCERRLOG_CE 0x1
+#define I3200_ECCERRLOG_UE 0x2
+#define I3200_ECCERRLOG_RANK_BITS 0x18000000
+#define I3200_ECCERRLOG_RANK_SHIFT 27
+#define I3200_ECCERRLOG_SYNDROME_BITS 0xff0000
+#define I3200_ECCERRLOG_SYNDROME_SHIFT 16
+#define I3200_CAPID0 0xe0 /* P.95 of spec for details */
+
+struct i3200_priv {
+ void __iomem *window;
+};
+
+static int nr_channels;
+
+static int how_many_channels(struct pci_dev *pdev)
+{
+ unsigned char capid0_8b; /* 8th byte of CAPID0 */
+
+ pci_read_config_byte(pdev, I3200_CAPID0 + 8, &capid0_8b);
+ if (capid0_8b & 0x20) { /* check DCD: Dual Channel Disable */
+ debugf0("In single channel mode.\n");
+ return 1;
+ } else {
+ debugf0("In dual channel mode.\n");
+ return 2;
+ }
+}
+
+static unsigned long eccerrlog_syndrome(u64 log)
+{
+ return (log & I3200_ECCERRLOG_SYNDROME_BITS) >>
+ I3200_ECCERRLOG_SYNDROME_SHIFT;
+}
+
+static int eccerrlog_row(int channel, u64 log)
+{
+ u64 rank = ((log & I3200_ECCERRLOG_RANK_BITS) >>
+ I3200_ECCERRLOG_RANK_SHIFT);
+ return rank | (channel * I3200_RANKS_PER_CHANNEL);
+}
+
+enum i3200_chips {
+ I3200 = 0,
+};
+
+struct i3200_dev_info {
+ const char *ctl_name;
+};
+
+struct i3200_error_info {
+ u16 errsts;
+ u16 errsts2;
+ u64 eccerrlog[I3200_CHANNELS];
+};
+
+static const struct i3200_dev_info i3200_devs[] = {
+ [I3200] = {
+ .ctl_name = "i3200"
+ },
+};
+
+static struct pci_dev *mci_pdev;
+static int i3200_registered = 1;
+
+
+static void i3200_clear_error_info(struct mem_ctl_info *mci)
+{
+ struct pci_dev *pdev;
+
+ pdev = to_pci_dev(mci->dev);
+
+ /*
+ * Clear any error bits.
+ * (Yes, we really clear bits by writing 1 to them.)
+ */
+ pci_write_bits16(pdev, I3200_ERRSTS, I3200_ERRSTS_BITS,
+ I3200_ERRSTS_BITS);
+}
+
+static void i3200_get_and_clear_error_info(struct mem_ctl_info *mci,
+ struct i3200_error_info *info)
+{
+ struct pci_dev *pdev;
+ struct i3200_priv *priv = mci->pvt_info;
+ void __iomem *window = priv->window;
+
+ pdev = to_pci_dev(mci->dev);
+
+ /*
+ * This is a mess because there is no atomic way to read all the
+ * registers at once and the registers can transition from CE being
+ * overwritten by UE.
+ */
+ pci_read_config_word(pdev, I3200_ERRSTS, &info->errsts);
+ if (!(info->errsts & I3200_ERRSTS_BITS))
+ return;
+
+ info->eccerrlog[0] = readq(window + I3200_C0ECCERRLOG);
+ if (nr_channels == 2)
+ info->eccerrlog[1] = readq(window + I3200_C1ECCERRLOG);
+
+ pci_read_config_word(pdev, I3200_ERRSTS, &info->errsts2);
+
+ /*
+ * If the error is the same for both reads then the first set
+ * of reads is valid. If there is a change then there is a CE
+ * with no info and the second set of reads is valid and
+ * should be UE info.
+ */
+ if ((info->errsts ^ info->errsts2) & I3200_ERRSTS_BITS) {
+ info->eccerrlog[0] = readq(window + I3200_C0ECCERRLOG);
+ if (nr_channels == 2)
+ info->eccerrlog[1] = readq(window + I3200_C1ECCERRLOG);
+ }
+
+ i3200_clear_error_info(mci);
+}
+
+static void i3200_process_error_info(struct mem_ctl_info *mci,
+ struct i3200_error_info *info)
+{
+ int channel;
+ u64 log;
+
+ if (!(info->errsts & I3200_ERRSTS_BITS))
+ return;
+
+ if ((info->errsts ^ info->errsts2) & I3200_ERRSTS_BITS) {
+ edac_mc_handle_ce_no_info(mci, "UE overwrote CE");
+ info->errsts = info->errsts2;
+ }
+
+ for (channel = 0; channel < nr_channels; channel++) {
+ log = info->eccerrlog[channel];
+ if (log & I3200_ECCERRLOG_UE) {
+ edac_mc_handle_ue(mci, 0, 0,
+ eccerrlog_row(channel, log),
+ "i3200 UE");
+ } else if (log & I3200_ECCERRLOG_CE) {
+ edac_mc_handle_ce(mci, 0, 0,
+ eccerrlog_syndrome(log),
+ eccerrlog_row(channel, log), 0,
+ "i3200 CE");
+ }
+ }
+}
+
+static void i3200_check(struct mem_ctl_info *mci)
+{
+ struct i3200_error_info info;
+
+ debugf1("MC%d: %s()\n", mci->mc_idx, __func__);
+ i3200_get_and_clear_error_info(mci, &info);
+ i3200_process_error_info(mci, &info);
+}
+
+
+void __iomem *i3200_map_mchbar(struct pci_dev *pdev)
+{
+ union {
+ u64 mchbar;
+ struct {
+ u32 mchbar_low;
+ u32 mchbar_high;
+ };
+ } u;
+ void __iomem *window;
+
+ pci_read_config_dword(pdev, I3200_MCHBAR_LOW, &u.mchbar_low);
+ pci_read_config_dword(pdev, I3200_MCHBAR_HIGH, &u.mchbar_high);
+ u.mchbar &= I3200_MCHBAR_MASK;
+
+ if (u.mchbar != (resource_size_t)u.mchbar) {
+ printk(KERN_ERR
+ "i3200: mmio space beyond accessible range (0x%llx)\n",
+ (unsigned long long)u.mchbar);
+ return NULL;
+ }
+
+ window = ioremap_nocache(u.mchbar, I3200_MMR_WINDOW_SIZE);
+ if (!window)
+ printk(KERN_ERR "i3200: cannot map mmio space at 0x%llx\n",
+ (unsigned long long)u.mchbar);
+
+ return window;
+}
+
+
+static void i3200_get_drbs(void __iomem *window,
+ u16 drbs[I3200_CHANNELS][I3200_RANKS_PER_CHANNEL])
+{
+ int i;
+
+ for (i = 0; i < I3200_RANKS_PER_CHANNEL; i++) {
+ drbs[0][i] = readw(window + I3200_C0DRB + 2*i) & I3200_DRB_MASK;
+ drbs[1][i] = readw(window + I3200_C1DRB + 2*i) & I3200_DRB_MASK;
+ }
+}
+
+static bool i3200_is_stacked(struct pci_dev *pdev,
+ u16 drbs[I3200_CHANNELS][I3200_RANKS_PER_CHANNEL])
+{
+ u16 tom;
+
+ pci_read_config_word(pdev, I3200_TOM, &tom);
+ tom &= I3200_TOM_MASK;
+
+ return drbs[I3200_CHANNELS - 1][I3200_RANKS_PER_CHANNEL - 1] == tom;
+}
+
+static unsigned long drb_to_nr_pages(
+ u16 drbs[I3200_CHANNELS][I3200_RANKS_PER_CHANNEL], bool stacked,
+ int channel, int rank)
+{
+ int n;
+
+ n = drbs[channel][rank];
+ if (rank > 0)
+ n -= drbs[channel][rank - 1];
+ if (stacked && (channel == 1) &&
+ drbs[channel][rank] == drbs[channel][I3200_RANKS_PER_CHANNEL - 1])
+ n -= drbs[0][I3200_RANKS_PER_CHANNEL - 1];
+
+ n <<= (I3200_DRB_SHIFT - PAGE_SHIFT);
+ return n;
+}
+
+static int i3200_probe1(struct pci_dev *pdev, int dev_idx)
+{
+ int rc;
+ int i;
+ struct mem_ctl_info *mci = NULL;
+ unsigned long last_page;
+ u16 drbs[I3200_CHANNELS][I3200_RANKS_PER_CHANNEL];
+ bool stacked;
+ void __iomem *window;
+ struct i3200_priv *priv;
+
+ debugf0("MC: %s()\n", __func__);
+
+ window = i3200_map_mchbar(pdev);
+ if (!window)
+ return -ENODEV;
+
+ i3200_get_drbs(window, drbs);
+ nr_channels = how_many_channels(pdev);
+
+ mci = edac_mc_alloc(sizeof(struct i3200_priv), I3200_RANKS,
+ nr_channels, 0);
+ if (!mci)
+ return -ENOMEM;
+
+ debugf3("MC: %s(): init mci\n", __func__);
+
+ mci->dev = &pdev->dev;
+ mci->mtype_cap = MEM_FLAG_DDR2;
+
+ mci->edac_ctl_cap = EDAC_FLAG_SECDED;
+ mci->edac_cap = EDAC_FLAG_SECDED;
+
+ mci->mod_name = EDAC_MOD_STR;
+ mci->mod_ver = I3200_REVISION;
+ mci->ctl_name = i3200_devs[dev_idx].ctl_name;
+ mci->dev_name = pci_name(pdev);
+ mci->edac_check = i3200_check;
+ mci->ctl_page_to_phys = NULL;
+ priv = mci->pvt_info;
+ priv->window = window;
+
+ stacked = i3200_is_stacked(pdev, drbs);
+
+ /*
+ * The dram rank boundary (DRB) reg values are boundary addresses
+ * for each DRAM rank with a granularity of 64MB. DRB regs are
+ * cumulative; the last one will contain the total memory
+ * contained in all ranks.
+ */
+ last_page = -1UL;
+ for (i = 0; i < mci->nr_csrows; i++) {
+ unsigned long nr_pages;
+ struct csrow_info *csrow = &mci->csrows[i];
+
+ nr_pages = drb_to_nr_pages(drbs, stacked,
+ i / I3200_RANKS_PER_CHANNEL,
+ i % I3200_RANKS_PER_CHANNEL);
+
+ if (nr_pages == 0) {
+ csrow->mtype = MEM_EMPTY;
+ continue;
+ }
+
+ csrow->first_page = last_page + 1;
+ last_page += nr_pages;
+ csrow->last_page = last_page;
+ csrow->nr_pages = nr_pages;
+
+ csrow->grain = nr_pages << PAGE_SHIFT;
+ csrow->mtype = MEM_DDR2;
+ csrow->dtype = DEV_UNKNOWN;
+ csrow->edac_mode = EDAC_UNKNOWN;
+ }
+
+ i3200_clear_error_info(mci);
+
+ rc = -ENODEV;
+ if (edac_mc_add_mc(mci)) {
+ debugf3("MC: %s(): failed edac_mc_add_mc()\n", __func__);
+ goto fail;
+ }
+
+ /* get this far and it's successful */
+ debugf3("MC: %s(): success\n", __func__);
+ return 0;
+
+fail:
+ iounmap(window);
+ if (mci)
+ edac_mc_free(mci);
+
+ return rc;
+}
+
+static int __devinit i3200_init_one(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ int rc;
+
+ debugf0("MC: %s()\n", __func__);
+
+ if (pci_enable_device(pdev) < 0)
+ return -EIO;
+
+ rc = i3200_probe1(pdev, ent->driver_data);
+ if (!mci_pdev)
+ mci_pdev = pci_dev_get(pdev);
+
+ return rc;
+}
+
+static void __devexit i3200_remove_one(struct pci_dev *pdev)
+{
+ struct mem_ctl_info *mci;
+ struct i3200_priv *priv;
+
+ debugf0("%s()\n", __func__);
+
+ mci = edac_mc_del_mc(&pdev->dev);
+ if (!mci)
+ return;
+
+ priv = mci->pvt_info;
+ iounmap(priv->window);
+
+ edac_mc_free(mci);
+}
+
+static const struct pci_device_id i3200_pci_tbl[] __devinitdata = {
+ {
+ PCI_VEND_DEV(INTEL, 3200_HB), PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ I3200},
+ {
+ 0,
+ } /* 0 terminated list. */
+};
+
+MODULE_DEVICE_TABLE(pci, i3200_pci_tbl);
+
+static struct pci_driver i3200_driver = {
+ .name = EDAC_MOD_STR,
+ .probe = i3200_init_one,
+ .remove = __devexit_p(i3200_remove_one),
+ .id_table = i3200_pci_tbl,
+};
+
+static int __init i3200_init(void)
+{
+ int pci_rc;
+
+ debugf3("MC: %s()\n", __func__);
+
+ /* Ensure that the OPSTATE is set correctly for POLL or NMI */
+ opstate_init();
+
+ pci_rc = pci_register_driver(&i3200_driver);
+ if (pci_rc < 0)
+ goto fail0;
+
+ if (!mci_pdev) {
+ i3200_registered = 0;
+ mci_pdev = pci_get_device(PCI_VENDOR_ID_INTEL,
+ PCI_DEVICE_ID_INTEL_3200_HB, NULL);
+ if (!mci_pdev) {
+ debugf0("i3200 pci_get_device fail\n");
+ pci_rc = -ENODEV;
+ goto fail1;
+ }
+
+ pci_rc = i3200_init_one(mci_pdev, i3200_pci_tbl);
+ if (pci_rc < 0) {
+ debugf0("i3200 init fail\n");
+ pci_rc = -ENODEV;
+ goto fail1;
+ }
+ }
+
+ return 0;
+
+fail1:
+ pci_unregister_driver(&i3200_driver);
+
+fail0:
+ if (mci_pdev)
+ pci_dev_put(mci_pdev);
+
+ return pci_rc;
+}
+
+static void __exit i3200_exit(void)
+{
+ debugf3("MC: %s()\n", __func__);
+
+ pci_unregister_driver(&i3200_driver);
+ if (!i3200_registered) {
+ i3200_remove_one(mci_pdev);
+ pci_dev_put(mci_pdev);
+ }
+}
+
+module_init(i3200_init);
+module_exit(i3200_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Akamai Technologies, Inc.");
+MODULE_DESCRIPTION("MC support for Intel 3200 memory hub controllers");
+
+module_param(edac_op_state, int, 0444);
+MODULE_PARM_DESC(edac_op_state, "EDAC Error Reporting state: 0=Poll,1=NMI");
#endif
static u32 orig_l2_err_disable;
+#ifdef CONFIG_MPC85xx
static u32 orig_hid1[2];
+#endif
/************************ MC SYSFS parts ***********************************/
{ .compatible = "fsl,mpc8560-l2-cache-controller", },
{ .compatible = "fsl,mpc8568-l2-cache-controller", },
{ .compatible = "fsl,mpc8572-l2-cache-controller", },
+ { .compatible = "fsl,p2020-l2-cache-controller", },
{},
};
csrow = &mci->csrows[index];
cs_bnds = in_be32(pdata->mc_vbase + MPC85XX_MC_CS_BNDS_0 +
(index * MPC85XX_MC_CS_BNDS_OFS));
- start = (cs_bnds & 0xfff0000) << 4;
- end = ((cs_bnds & 0xfff) << 20);
- if (start)
- start |= 0xfffff;
- if (end)
- end |= 0xfffff;
+
+ start = (cs_bnds & 0xffff0000) >> 16;
+ end = (cs_bnds & 0x0000ffff);
if (start == end)
continue; /* not populated */
+ start <<= (24 - PAGE_SHIFT);
+ end <<= (24 - PAGE_SHIFT);
+ end |= (1 << (24 - PAGE_SHIFT)) - 1;
+
csrow->first_page = start >> PAGE_SHIFT;
csrow->last_page = end >> PAGE_SHIFT;
- csrow->nr_pages = csrow->last_page + 1 - csrow->first_page;
+ csrow->nr_pages = end + 1 - start;
csrow->grain = 8;
csrow->mtype = mtype;
csrow->dtype = DEV_UNKNOWN;
{ .compatible = "fsl,mpc8560-memory-controller", },
{ .compatible = "fsl,mpc8568-memory-controller", },
{ .compatible = "fsl,mpc8572-memory-controller", },
+ { .compatible = "fsl,mpc8349-memory-controller", },
+ { .compatible = "fsl,p2020-memory-controller", },
{},
};
},
};
-
+#ifdef CONFIG_MPC85xx
static void __init mpc85xx_mc_clear_rfxe(void *data)
{
orig_hid1[smp_processor_id()] = mfspr(SPRN_HID1);
mtspr(SPRN_HID1, (orig_hid1[smp_processor_id()] & ~0x20000));
}
-
+#endif
static int __init mpc85xx_mc_init(void)
{
printk(KERN_WARNING EDAC_MOD_STR "PCI fails to register\n");
#endif
+#ifdef CONFIG_MPC85xx
/*
* need to clear HID1[RFXE] to disable machine check int
* so we can catch it
*/
if (edac_op_state == EDAC_OPSTATE_INT)
on_each_cpu(mpc85xx_mc_clear_rfxe, NULL, 0);
+#endif
return 0;
}
module_init(mpc85xx_mc_init);
+#ifdef CONFIG_MPC85xx
static void __exit mpc85xx_mc_restore_hid1(void *data)
{
mtspr(SPRN_HID1, orig_hid1[smp_processor_id()]);
}
+#endif
static void __exit mpc85xx_mc_exit(void)
{
+#ifdef CONFIG_MPC85xx
on_each_cpu(mpc85xx_mc_restore_hid1, NULL, 0);
+#endif
#ifdef CONFIG_PCI
of_unregister_platform_driver(&mpc85xx_pci_err_driver);
#endif
return -ENOENT;
}
- pci_serr = ioremap(r->start, r->end - r->start + 1);
+ pci_serr = ioremap(r->start, resource_size(r));
if (!pci_serr)
return -ENOMEM;
if (!devm_request_mem_region(&pdev->dev,
r->start,
- r->end - r->start + 1,
+ resource_size(r),
pdata->name)) {
printk(KERN_ERR "%s: Error while requesting mem region\n",
__func__);
pdata->pci_vbase = devm_ioremap(&pdev->dev,
r->start,
- r->end - r->start + 1);
+ resource_size(r));
if (!pdata->pci_vbase) {
printk(KERN_ERR "%s: Unable to setup PCI err regs\n", __func__);
res = -ENOMEM;
if (!devm_request_mem_region(&pdev->dev,
r->start,
- r->end - r->start + 1,
+ resource_size(r),
pdata->name)) {
printk(KERN_ERR "%s: Error while request mem region\n",
__func__);
pdata->sram_vbase = devm_ioremap(&pdev->dev,
r->start,
- r->end - r->start + 1);
+ resource_size(r));
if (!pdata->sram_vbase) {
printk(KERN_ERR "%s: Unable to setup SRAM err regs\n",
__func__);
if (!devm_request_mem_region(&pdev->dev,
r->start,
- r->end - r->start + 1,
+ resource_size(r),
pdata->name)) {
printk(KERN_ERR "%s: Error while requesting mem region\n",
__func__);
pdata->cpu_vbase[0] = devm_ioremap(&pdev->dev,
r->start,
- r->end - r->start + 1);
+ resource_size(r));
if (!pdata->cpu_vbase[0]) {
printk(KERN_ERR "%s: Unable to setup CPU err regs\n", __func__);
res = -ENOMEM;
if (!devm_request_mem_region(&pdev->dev,
r->start,
- r->end - r->start + 1,
+ resource_size(r),
pdata->name)) {
printk(KERN_ERR "%s: Error while requesting mem region\n",
__func__);
pdata->cpu_vbase[1] = devm_ioremap(&pdev->dev,
r->start,
- r->end - r->start + 1);
+ resource_size(r));
if (!pdata->cpu_vbase[1]) {
printk(KERN_ERR "%s: Unable to setup CPU err regs\n", __func__);
res = -ENOMEM;
if (!devm_request_mem_region(&pdev->dev,
r->start,
- r->end - r->start + 1,
+ resource_size(r),
pdata->name)) {
printk(KERN_ERR "%s: Error while requesting mem region\n",
__func__);
pdata->mc_vbase = devm_ioremap(&pdev->dev,
r->start,
- r->end - r->start + 1);
+ resource_size(r));
if (!pdata->mc_vbase) {
printk(KERN_ERR "%s: Unable to setup MC err regs\n", __func__);
res = -ENOMEM;
#include <linux/mutex.h>
#include <linux/poll.h>
#include <linux/preempt.h>
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/time.h>
#include <linux/uaccess.h>
return single_open(file, gpiolib_show, NULL);
}
-static struct file_operations gpiolib_operations = {
+static const struct file_operations gpiolib_operations = {
.open = gpiolib_open,
.read = seq_read,
.llseek = seq_lseek,
select BACKLIGHT_CLASS_DEVICE if ACPI
select INPUT if ACPI
select ACPI_VIDEO if ACPI
+ select ACPI_BUTTON if ACPI
help
Choose this option if you have a system that has Intel 830M, 845G,
852GM, 855GM 865G or 915G integrated graphics. If M is selected, the
list_for_each_entry_safe(mode, t, &connector->user_modes, head)
drm_mode_remove(connector, mode);
+ kfree(connector->fb_helper_private);
mutex_lock(&dev->mode_config.mutex);
drm_mode_object_put(dev, &connector->base);
list_del(&connector->head);
#include "drmP.h"
#include "drm_crtc.h"
#include "drm_crtc_helper.h"
+#include "drm_fb_helper.h"
static void drm_mode_validate_flag(struct drm_connector *connector,
int flags)
list_for_each_entry_safe(mode, t, &connector->modes, head)
mode->status = MODE_UNVERIFIED;
- connector->status = connector->funcs->detect(connector);
+ if (connector->force) {
+ if (connector->force == DRM_FORCE_ON)
+ connector->status = connector_status_connected;
+ else
+ connector->status = connector_status_disconnected;
+ if (connector->funcs->force)
+ connector->funcs->force(connector);
+ } else
+ connector->status = connector->funcs->detect(connector);
if (connector->status == connector_status_disconnected) {
DRM_DEBUG_KMS("%s is disconnected\n",
return NULL;
}
+static bool drm_has_cmdline_mode(struct drm_connector *connector)
+{
+ struct drm_fb_helper_connector *fb_help_conn = connector->fb_helper_private;
+ struct drm_fb_helper_cmdline_mode *cmdline_mode;
+
+ if (!fb_help_conn)
+ return false;
+
+ cmdline_mode = &fb_help_conn->cmdline_mode;
+ return cmdline_mode->specified;
+}
+
+static struct drm_display_mode *drm_pick_cmdline_mode(struct drm_connector *connector, int width, int height)
+{
+ struct drm_fb_helper_connector *fb_help_conn = connector->fb_helper_private;
+ struct drm_fb_helper_cmdline_mode *cmdline_mode;
+ struct drm_display_mode *mode = NULL;
+
+ if (!fb_help_conn)
+ return mode;
+
+ cmdline_mode = &fb_help_conn->cmdline_mode;
+ if (cmdline_mode->specified == false)
+ return mode;
+
+ /* attempt to find a matching mode in the list of modes
+ * we have gotten so far, if not add a CVT mode that conforms
+ */
+ if (cmdline_mode->rb || cmdline_mode->margins)
+ goto create_mode;
+
+ list_for_each_entry(mode, &connector->modes, head) {
+ /* check width/height */
+ if (mode->hdisplay != cmdline_mode->xres ||
+ mode->vdisplay != cmdline_mode->yres)
+ continue;
+
+ if (cmdline_mode->refresh_specified) {
+ if (mode->vrefresh != cmdline_mode->refresh)
+ continue;
+ }
+
+ if (cmdline_mode->interlace) {
+ if (!(mode->flags & DRM_MODE_FLAG_INTERLACE))
+ continue;
+ }
+ return mode;
+ }
+
+create_mode:
+ mode = drm_cvt_mode(connector->dev, cmdline_mode->xres,
+ cmdline_mode->yres,
+ cmdline_mode->refresh_specified ? cmdline_mode->refresh : 60,
+ cmdline_mode->rb, cmdline_mode->interlace,
+ cmdline_mode->margins);
+ list_add(&mode->head, &connector->modes);
+ return mode;
+}
+
static bool drm_connector_enabled(struct drm_connector *connector, bool strict)
{
bool enable;
continue;
}
- DRM_DEBUG_KMS("looking for preferred mode on connector %d\n",
- connector->base.id);
+ DRM_DEBUG_KMS("looking for cmdline mode on connector %d\n",
+ connector->base.id);
- modes[i] = drm_has_preferred_mode(connector, width, height);
+ /* got for command line mode first */
+ modes[i] = drm_pick_cmdline_mode(connector, width, height);
+ if (!modes[i]) {
+ DRM_DEBUG_KMS("looking for preferred mode on connector %d\n",
+ connector->base.id);
+ modes[i] = drm_has_preferred_mode(connector, width, height);
+ }
/* No preferred modes, pick one off the list */
if (!modes[i] && !list_empty(&connector->modes)) {
list_for_each_entry(modes[i], &connector->modes, head)
my_score = 1;
if (connector->status == connector_status_connected)
my_score++;
+ if (drm_has_cmdline_mode(connector))
+ my_score++;
if (drm_has_preferred_mode(connector, width, height))
my_score++;
{
int count = 0;
+ drm_fb_helper_parse_command_line(dev);
+
count = drm_helper_probe_connector_modes(dev,
dev->mode_config.max_width,
dev->mode_config.max_height);
/*
* we shouldn't end up with no modes here.
*/
- WARN(!count, "Connected connector with 0 modes\n");
+ WARN(!count, "No connectors reported connected with modes\n");
drm_setup_crtcs(dev);
/* Valid EDID header has these bytes */
-static u8 edid_header[] = { 0x00, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x00 };
+static const u8 edid_header[] = {
+ 0x00, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x00
+};
/**
* edid_is_valid - sanity check EDID data
}
return mode;
}
+
+/*
+ * 0 is reserved. The spec says 0x01 fill for unused timings. Some old
+ * monitors fill with ascii space (0x20) instead.
+ */
+static int
+bad_std_timing(u8 a, u8 b)
+{
+ return (a == 0x00 && b == 0x00) ||
+ (a == 0x01 && b == 0x01) ||
+ (a == 0x20 && b == 0x20);
+}
+
/**
* drm_mode_std - convert standard mode info (width, height, refresh) into mode
* @t: standard timing params
*/
struct drm_display_mode *drm_mode_std(struct drm_device *dev,
struct std_timing *t,
+ int revision,
int timing_level)
{
struct drm_display_mode *mode;
unsigned vfreq = (t->vfreq_aspect & EDID_TIMING_VFREQ_MASK)
>> EDID_TIMING_VFREQ_SHIFT;
+ if (bad_std_timing(t->hsize, t->vfreq_aspect))
+ return NULL;
+
/* According to the EDID spec, the hdisplay = hsize * 8 + 248 */
hsize = t->hsize * 8 + 248;
/* vrefresh_rate = vfreq + 60 */
vrefresh_rate = vfreq + 60;
/* the vdisplay is calculated based on the aspect ratio */
- if (aspect_ratio == 0)
- vsize = (hsize * 10) / 16;
- else if (aspect_ratio == 1)
+ if (aspect_ratio == 0) {
+ if (revision < 3)
+ vsize = hsize;
+ else
+ vsize = (hsize * 10) / 16;
+ } else if (aspect_ratio == 1)
vsize = (hsize * 3) / 4;
else if (aspect_ratio == 2)
vsize = (hsize * 4) / 5;
vsize = (hsize * 9) / 16;
/* HDTV hack */
if (hsize == 1360 && vsize == 765 && vrefresh_rate == 60) {
- mode = drm_cvt_mode(dev, hsize, vsize, vrefresh_rate, 0, 0);
+ mode = drm_cvt_mode(dev, hsize, vsize, vrefresh_rate, 0, 0,
+ false);
mode->hdisplay = 1366;
mode->vsync_start = mode->vsync_start - 1;
mode->vsync_end = mode->vsync_end - 1;
mode = drm_gtf_mode(dev, hsize, vsize, vrefresh_rate, 0, 0);
break;
case LEVEL_CVT:
- mode = drm_cvt_mode(dev, hsize, vsize, vrefresh_rate, 0, 0);
+ mode = drm_cvt_mode(dev, hsize, vsize, vrefresh_rate, 0, 0,
+ false);
break;
}
return mode;
continue;
newmode = drm_mode_std(dev, &edid->standard_timings[i],
- timing_level);
+ edid->revision, timing_level);
if (newmode) {
drm_mode_probed_add(connector, newmode);
modes++;
case EDID_DETAIL_MONITOR_CPDATA:
break;
case EDID_DETAIL_STD_MODES:
- /* Five modes per detailed section */
- for (j = 0; j < 5; i++) {
+ for (j = 0; j < 6; i++) {
struct std_timing *std;
struct drm_display_mode *newmode;
std = &data->data.timings[j];
newmode = drm_mode_std(dev, std,
+ edid->revision,
timing_level);
if (newmode) {
drm_mode_probed_add(connector, newmode);
struct drm_display_mode *newmode;
std = &data->data.timings[j];
- newmode = drm_mode_std(dev, std, timing_level);
+ newmode = drm_mode_std(dev, std,
+ edid->revision,
+ timing_level);
if (newmode) {
drm_mode_probed_add(connector, newmode);
modes++;
static LIST_HEAD(kernel_fb_helper_list);
+int drm_fb_helper_add_connector(struct drm_connector *connector)
+{
+ connector->fb_helper_private = kzalloc(sizeof(struct drm_fb_helper_connector), GFP_KERNEL);
+ if (!connector->fb_helper_private)
+ return -ENOMEM;
+
+ return 0;
+}
+EXPORT_SYMBOL(drm_fb_helper_add_connector);
+
+static int my_atoi(const char *name)
+{
+ int val = 0;
+
+ for (;; name++) {
+ switch (*name) {
+ case '0' ... '9':
+ val = 10*val+(*name-'0');
+ break;
+ default:
+ return val;
+ }
+ }
+}
+
+/**
+ * drm_fb_helper_connector_parse_command_line - parse command line for connector
+ * @connector - connector to parse line for
+ * @mode_option - per connector mode option
+ *
+ * This parses the connector specific then generic command lines for
+ * modes and options to configure the connector.
+ *
+ * This uses the same parameters as the fb modedb.c, except for extra
+ * <xres>x<yres>[M][R][-<bpp>][@<refresh>][i][m][eDd]
+ *
+ * enable/enable Digital/disable bit at the end
+ */
+static bool drm_fb_helper_connector_parse_command_line(struct drm_connector *connector,
+ const char *mode_option)
+{
+ const char *name;
+ unsigned int namelen;
+ int res_specified = 0, bpp_specified = 0, refresh_specified = 0;
+ unsigned int xres = 0, yres = 0, bpp = 32, refresh = 0;
+ int yres_specified = 0, cvt = 0, rb = 0, interlace = 0, margins = 0;
+ int i;
+ enum drm_connector_force force = DRM_FORCE_UNSPECIFIED;
+ struct drm_fb_helper_connector *fb_help_conn = connector->fb_helper_private;
+ struct drm_fb_helper_cmdline_mode *cmdline_mode;
+
+ if (!fb_help_conn)
+ return false;
+
+ cmdline_mode = &fb_help_conn->cmdline_mode;
+ if (!mode_option)
+ mode_option = fb_mode_option;
+
+ if (!mode_option) {
+ cmdline_mode->specified = false;
+ return false;
+ }
+
+ name = mode_option;
+ namelen = strlen(name);
+ for (i = namelen-1; i >= 0; i--) {
+ switch (name[i]) {
+ case '@':
+ namelen = i;
+ if (!refresh_specified && !bpp_specified &&
+ !yres_specified) {
+ refresh = my_atoi(&name[i+1]);
+ refresh_specified = 1;
+ if (cvt || rb)
+ cvt = 0;
+ } else
+ goto done;
+ break;
+ case '-':
+ namelen = i;
+ if (!bpp_specified && !yres_specified) {
+ bpp = my_atoi(&name[i+1]);
+ bpp_specified = 1;
+ if (cvt || rb)
+ cvt = 0;
+ } else
+ goto done;
+ break;
+ case 'x':
+ if (!yres_specified) {
+ yres = my_atoi(&name[i+1]);
+ yres_specified = 1;
+ } else
+ goto done;
+ case '0' ... '9':
+ break;
+ case 'M':
+ if (!yres_specified)
+ cvt = 1;
+ break;
+ case 'R':
+ if (!cvt)
+ rb = 1;
+ break;
+ case 'm':
+ if (!cvt)
+ margins = 1;
+ break;
+ case 'i':
+ if (!cvt)
+ interlace = 1;
+ break;
+ case 'e':
+ force = DRM_FORCE_ON;
+ break;
+ case 'D':
+ if ((connector->connector_type != DRM_MODE_CONNECTOR_DVII) ||
+ (connector->connector_type != DRM_MODE_CONNECTOR_HDMIB))
+ force = DRM_FORCE_ON;
+ else
+ force = DRM_FORCE_ON_DIGITAL;
+ break;
+ case 'd':
+ force = DRM_FORCE_OFF;
+ break;
+ default:
+ goto done;
+ }
+ }
+ if (i < 0 && yres_specified) {
+ xres = my_atoi(name);
+ res_specified = 1;
+ }
+done:
+
+ DRM_DEBUG_KMS("cmdline mode for connector %s %dx%d@%dHz%s%s%s\n",
+ drm_get_connector_name(connector), xres, yres,
+ (refresh) ? refresh : 60, (rb) ? " reduced blanking" :
+ "", (margins) ? " with margins" : "", (interlace) ?
+ " interlaced" : "");
+
+ if (force) {
+ const char *s;
+ switch (force) {
+ case DRM_FORCE_OFF: s = "OFF"; break;
+ case DRM_FORCE_ON_DIGITAL: s = "ON - dig"; break;
+ default:
+ case DRM_FORCE_ON: s = "ON"; break;
+ }
+
+ DRM_INFO("forcing %s connector %s\n",
+ drm_get_connector_name(connector), s);
+ connector->force = force;
+ }
+
+ if (res_specified) {
+ cmdline_mode->specified = true;
+ cmdline_mode->xres = xres;
+ cmdline_mode->yres = yres;
+ }
+
+ if (refresh_specified) {
+ cmdline_mode->refresh_specified = true;
+ cmdline_mode->refresh = refresh;
+ }
+
+ if (bpp_specified) {
+ cmdline_mode->bpp_specified = true;
+ cmdline_mode->bpp = bpp;
+ }
+ cmdline_mode->rb = rb ? true : false;
+ cmdline_mode->cvt = cvt ? true : false;
+ cmdline_mode->interlace = interlace ? true : false;
+
+ return true;
+}
+
+int drm_fb_helper_parse_command_line(struct drm_device *dev)
+{
+ struct drm_connector *connector;
+
+ list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ char *option = NULL;
+
+ /* do something on return - turn off connector maybe */
+ if (fb_get_options(drm_get_connector_name(connector), &option))
+ continue;
+
+ drm_fb_helper_connector_parse_command_line(connector, option);
+ }
+ return 0;
+}
+
bool drm_fb_helper_force_kernel_mode(void)
{
int i = 0;
}
EXPORT_SYMBOL(drm_fb_helper_restore);
+#ifdef CONFIG_MAGIC_SYSRQ
static void drm_fb_helper_restore_work_fn(struct work_struct *ignored)
{
drm_fb_helper_restore();
.help_msg = "force-fb(V)",
.action_msg = "Restore framebuffer console",
};
+#endif
static void drm_fb_helper_on(struct fb_info *info)
{
uint32_t fb_height,
uint32_t surface_width,
uint32_t surface_height,
+ uint32_t surface_depth,
+ uint32_t surface_bpp,
struct drm_framebuffer **fb_ptr))
{
struct drm_crtc *crtc;
struct drm_framebuffer *fb;
struct drm_mode_set *modeset = NULL;
struct drm_fb_helper *fb_helper;
+ uint32_t surface_depth = 24, surface_bpp = 32;
/* first up get a count of crtcs now in use and new min/maxes width/heights */
+ list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+ struct drm_fb_helper_connector *fb_help_conn = connector->fb_helper_private;
+
+ struct drm_fb_helper_cmdline_mode *cmdline_mode;
+
+ if (!fb_help_conn)
+ continue;
+
+ cmdline_mode = &fb_help_conn->cmdline_mode;
+
+ if (cmdline_mode->bpp_specified) {
+ switch (cmdline_mode->bpp) {
+ case 8:
+ surface_depth = surface_bpp = 8;
+ break;
+ case 15:
+ surface_depth = 15;
+ surface_bpp = 16;
+ break;
+ case 16:
+ surface_depth = surface_bpp = 16;
+ break;
+ case 24:
+ surface_depth = surface_bpp = 24;
+ break;
+ case 32:
+ surface_depth = 24;
+ surface_bpp = 32;
+ break;
+ }
+ break;
+ }
+ }
+
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
if (drm_helper_crtc_in_use(crtc)) {
if (crtc->desired_mode) {
/* do we have an fb already? */
if (list_empty(&dev->mode_config.fb_kernel_list)) {
ret = (*fb_create)(dev, fb_width, fb_height, surface_width,
- surface_height, &fb);
+ surface_height, surface_depth, surface_bpp,
+ &fb);
if (ret)
return -EINVAL;
new_fb = 1;
if (IS_ERR(obj->filp))
goto free;
+ /* Basically we want to disable the OOM killer and handle ENOMEM
+ * ourselves by sacrificing pages from cached buffers.
+ * XXX shmem_file_[gs]et_gfp_mask()
+ */
+ mapping_set_gfp_mask(obj->filp->f_path.dentry->d_inode->i_mapping,
+ GFP_HIGHUSER |
+ __GFP_COLD |
+ __GFP_FS |
+ __GFP_RECLAIMABLE |
+ __GFP_NORETRY |
+ __GFP_NOWARN |
+ __GFP_NOMEMALLOC);
+
kref_init(&obj->refcount);
kref_init(&obj->handlecount);
obj->size = size;
#define HV_FACTOR 1000
struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay,
int vdisplay, int vrefresh,
- bool reduced, bool interlaced)
+ bool reduced, bool interlaced, bool margins)
{
/* 1) top/bottom margin size (% of height) - default: 1.8, */
#define CVT_MARGIN_PERCENTAGE 18
/* Pixel Clock step (kHz) */
#define CVT_CLOCK_STEP 250
struct drm_display_mode *drm_mode;
- bool margins = false;
unsigned int vfieldrate, hperiod;
int hdisplay_rnd, hmargin, vdisplay_rnd, vmargin, vsync;
int interlace;
}
/** AGP virtual memory operations */
-static struct vm_operations_struct drm_vm_ops = {
+static const struct vm_operations_struct drm_vm_ops = {
.fault = drm_vm_fault,
.open = drm_vm_open,
.close = drm_vm_close,
};
/** Shared virtual memory operations */
-static struct vm_operations_struct drm_vm_shm_ops = {
+static const struct vm_operations_struct drm_vm_shm_ops = {
.fault = drm_vm_shm_fault,
.open = drm_vm_open,
.close = drm_vm_shm_close,
};
/** DMA virtual memory operations */
-static struct vm_operations_struct drm_vm_dma_ops = {
+static const struct vm_operations_struct drm_vm_dma_ops = {
.fault = drm_vm_dma_fault,
.open = drm_vm_open,
.close = drm_vm_close,
};
/** Scatter-gather virtual memory operations */
-static struct vm_operations_struct drm_vm_sg_ops = {
+static const struct vm_operations_struct drm_vm_sg_ops = {
.fault = drm_vm_sg_fault,
.open = drm_vm_open,
.close = drm_vm_close,
i915_gem.o \
i915_gem_debug.o \
i915_gem_tiling.o \
+ i915_trace_points.o \
intel_display.o \
intel_crt.o \
intel_lvds.o \
{
struct drm_gem_object *obj = obj_priv->obj;
- seq_printf(m, " %p: %s %08x %08x %d",
+ seq_printf(m, " %p: %s %8zd %08x %08x %d %s",
obj,
get_pin_flag(obj_priv),
+ obj->size,
obj->read_domains, obj->write_domain,
- obj_priv->last_rendering_seqno);
+ obj_priv->last_rendering_seqno,
+ obj_priv->dirty ? "dirty" : "");
if (obj->name)
seq_printf(m, " (name: %d)", obj->name);
#include "intel_drv.h"
#include "i915_drm.h"
#include "i915_drv.h"
+#include "i915_trace.h"
#include <linux/vgaarb.h>
/* Really want an OS-independent resettable timer. Would like to have
u32 last_head = I915_READ(PRB0_HEAD) & HEAD_ADDR;
int i;
+ trace_i915_ring_wait_begin (dev);
+
for (i = 0; i < 100000; i++) {
ring->head = I915_READ(PRB0_HEAD) & HEAD_ADDR;
acthd = I915_READ(acthd_reg);
ring->space = ring->head - (ring->tail + 8);
if (ring->space < 0)
ring->space += ring->Size;
- if (ring->space >= n)
+ if (ring->space >= n) {
+ trace_i915_ring_wait_end (dev);
return 0;
+ }
if (dev->primary->master) {
struct drm_i915_master_private *master_priv = dev->primary->master->driver_priv;
}
+ trace_i915_ring_wait_end (dev);
return -EBUSY;
}
* how much was set aside so we can use it for our own purposes.
*/
static int i915_probe_agp(struct drm_device *dev, uint32_t *aperture_size,
- uint32_t *preallocated_size)
+ uint32_t *preallocated_size,
+ uint32_t *start)
{
struct drm_i915_private *dev_priv = dev->dev_private;
u16 tmp = 0;
return -1;
}
*preallocated_size = stolen - overhead;
+ *start = overhead;
return 0;
}
+#define PTE_ADDRESS_MASK 0xfffff000
+#define PTE_ADDRESS_MASK_HIGH 0x000000f0 /* i915+ */
+#define PTE_MAPPING_TYPE_UNCACHED (0 << 1)
+#define PTE_MAPPING_TYPE_DCACHE (1 << 1) /* i830 only */
+#define PTE_MAPPING_TYPE_CACHED (3 << 1)
+#define PTE_MAPPING_TYPE_MASK (3 << 1)
+#define PTE_VALID (1 << 0)
+
+/**
+ * i915_gtt_to_phys - take a GTT address and turn it into a physical one
+ * @dev: drm device
+ * @gtt_addr: address to translate
+ *
+ * Some chip functions require allocations from stolen space but need the
+ * physical address of the memory in question. We use this routine
+ * to get a physical address suitable for register programming from a given
+ * GTT address.
+ */
+static unsigned long i915_gtt_to_phys(struct drm_device *dev,
+ unsigned long gtt_addr)
+{
+ unsigned long *gtt;
+ unsigned long entry, phys;
+ int gtt_bar = IS_I9XX(dev) ? 0 : 1;
+ int gtt_offset, gtt_size;
+
+ if (IS_I965G(dev)) {
+ if (IS_G4X(dev) || IS_IGDNG(dev)) {
+ gtt_offset = 2*1024*1024;
+ gtt_size = 2*1024*1024;
+ } else {
+ gtt_offset = 512*1024;
+ gtt_size = 512*1024;
+ }
+ } else {
+ gtt_bar = 3;
+ gtt_offset = 0;
+ gtt_size = pci_resource_len(dev->pdev, gtt_bar);
+ }
+
+ gtt = ioremap_wc(pci_resource_start(dev->pdev, gtt_bar) + gtt_offset,
+ gtt_size);
+ if (!gtt) {
+ DRM_ERROR("ioremap of GTT failed\n");
+ return 0;
+ }
+
+ entry = *(volatile u32 *)(gtt + (gtt_addr / 1024));
+
+ DRM_DEBUG("GTT addr: 0x%08lx, PTE: 0x%08lx\n", gtt_addr, entry);
+
+ /* Mask out these reserved bits on this hardware. */
+ if (!IS_I9XX(dev) || IS_I915G(dev) || IS_I915GM(dev) ||
+ IS_I945G(dev) || IS_I945GM(dev)) {
+ entry &= ~PTE_ADDRESS_MASK_HIGH;
+ }
+
+ /* If it's not a mapping type we know, then bail. */
+ if ((entry & PTE_MAPPING_TYPE_MASK) != PTE_MAPPING_TYPE_UNCACHED &&
+ (entry & PTE_MAPPING_TYPE_MASK) != PTE_MAPPING_TYPE_CACHED) {
+ iounmap(gtt);
+ return 0;
+ }
+
+ if (!(entry & PTE_VALID)) {
+ DRM_ERROR("bad GTT entry in stolen space\n");
+ iounmap(gtt);
+ return 0;
+ }
+
+ iounmap(gtt);
+
+ phys =(entry & PTE_ADDRESS_MASK) |
+ ((uint64_t)(entry & PTE_ADDRESS_MASK_HIGH) << (32 - 4));
+
+ DRM_DEBUG("GTT addr: 0x%08lx, phys addr: 0x%08lx\n", gtt_addr, phys);
+
+ return phys;
+}
+
+static void i915_warn_stolen(struct drm_device *dev)
+{
+ DRM_ERROR("not enough stolen space for compressed buffer, disabling\n");
+ DRM_ERROR("hint: you may be able to increase stolen memory size in the BIOS to avoid this\n");
+}
+
+static void i915_setup_compression(struct drm_device *dev, int size)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_mm_node *compressed_fb, *compressed_llb;
+ unsigned long cfb_base, ll_base;
+
+ /* Leave 1M for line length buffer & misc. */
+ compressed_fb = drm_mm_search_free(&dev_priv->vram, size, 4096, 0);
+ if (!compressed_fb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ compressed_fb = drm_mm_get_block(compressed_fb, size, 4096);
+ if (!compressed_fb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ cfb_base = i915_gtt_to_phys(dev, compressed_fb->start);
+ if (!cfb_base) {
+ DRM_ERROR("failed to get stolen phys addr, disabling FBC\n");
+ drm_mm_put_block(compressed_fb);
+ }
+
+ if (!IS_GM45(dev)) {
+ compressed_llb = drm_mm_search_free(&dev_priv->vram, 4096,
+ 4096, 0);
+ if (!compressed_llb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ compressed_llb = drm_mm_get_block(compressed_llb, 4096, 4096);
+ if (!compressed_llb) {
+ i915_warn_stolen(dev);
+ return;
+ }
+
+ ll_base = i915_gtt_to_phys(dev, compressed_llb->start);
+ if (!ll_base) {
+ DRM_ERROR("failed to get stolen phys addr, disabling FBC\n");
+ drm_mm_put_block(compressed_fb);
+ drm_mm_put_block(compressed_llb);
+ }
+ }
+
+ dev_priv->cfb_size = size;
+
+ if (IS_GM45(dev)) {
+ g4x_disable_fbc(dev);
+ I915_WRITE(DPFC_CB_BASE, compressed_fb->start);
+ } else {
+ i8xx_disable_fbc(dev);
+ I915_WRITE(FBC_CFB_BASE, cfb_base);
+ I915_WRITE(FBC_LL_BASE, ll_base);
+ }
+
+ DRM_DEBUG("FBC base 0x%08lx, ll base 0x%08lx, size %dM\n", cfb_base,
+ ll_base, size >> 20);
+}
+
/* true = enable decode, false = disable decoder */
static unsigned int i915_vga_set_decode(void *cookie, bool state)
{
}
static int i915_load_modeset_init(struct drm_device *dev,
+ unsigned long prealloc_start,
unsigned long prealloc_size,
unsigned long agp_size)
{
/* Basic memrange allocator for stolen space (aka vram) */
drm_mm_init(&dev_priv->vram, 0, prealloc_size);
+ DRM_INFO("set up %ldM of stolen space\n", prealloc_size / (1024*1024));
+
+ /* We're off and running w/KMS */
+ dev_priv->mm.suspended = 0;
/* Let GEM Manage from end of prealloc space to end of aperture.
*
*/
i915_gem_do_init(dev, prealloc_size, agp_size - 4096);
+ mutex_lock(&dev->struct_mutex);
ret = i915_gem_init_ringbuffer(dev);
+ mutex_unlock(&dev->struct_mutex);
if (ret)
goto out;
+ /* Try to set up FBC with a reasonable compressed buffer size */
+ if (IS_MOBILE(dev) && (IS_I9XX(dev) || IS_I965G(dev) || IS_GM45(dev)) &&
+ i915_powersave) {
+ int cfb_size;
+
+ /* Try to get an 8M buffer... */
+ if (prealloc_size > (9*1024*1024))
+ cfb_size = 8*1024*1024;
+ else /* fall back to 7/8 of the stolen space */
+ cfb_size = prealloc_size * 7 / 8;
+ i915_setup_compression(dev, cfb_size);
+ }
+
/* Allow hardware batchbuffers unless told otherwise.
*/
dev_priv->allow_batchbuffer = 1;
struct drm_i915_private *dev_priv = dev->dev_private;
resource_size_t base, size;
int ret = 0, mmio_bar = IS_I9XX(dev) ? 0 : 1;
- uint32_t agp_size, prealloc_size;
+ uint32_t agp_size, prealloc_size, prealloc_start;
/* i915 has 4 more counters */
dev->counters += 4;
"performance may suffer.\n");
}
- ret = i915_probe_agp(dev, &agp_size, &prealloc_size);
+ ret = i915_probe_agp(dev, &agp_size, &prealloc_size, &prealloc_start);
if (ret)
goto out_iomapfree;
return ret;
}
+ /* Start out suspended */
+ dev_priv->mm.suspended = 1;
+
if (drm_core_check_feature(dev, DRIVER_MODESET)) {
- ret = i915_load_modeset_init(dev, prealloc_size, agp_size);
+ ret = i915_load_modeset_init(dev, prealloc_start,
+ prealloc_size, agp_size);
if (ret < 0) {
DRM_ERROR("failed to init modeset\n");
goto out_workqueue_free;
if (!IS_IGDNG(dev))
intel_opregion_init(dev, 0);
+ setup_timer(&dev_priv->hangcheck_timer, i915_hangcheck_elapsed,
+ (unsigned long) dev);
return 0;
out_workqueue_free:
struct drm_i915_private *dev_priv = dev->dev_private;
destroy_workqueue(dev_priv->wq);
+ del_timer_sync(&dev_priv->hangcheck_timer);
io_mapping_free(dev_priv->mm.gtt_mapping);
if (dev_priv->mm.gtt_mtrr >= 0) {
DRM_IOCTL_DEF(DRM_I915_GEM_GET_TILING, i915_gem_get_tiling, 0),
DRM_IOCTL_DEF(DRM_I915_GEM_GET_APERTURE, i915_gem_get_aperture_ioctl, 0),
DRM_IOCTL_DEF(DRM_I915_GET_PIPE_FROM_CRTC_ID, intel_get_pipe_from_crtc_id, 0),
+ DRM_IOCTL_DEF(DRM_I915_GEM_MADVISE, i915_gem_madvise_ioctl, 0),
};
int i915_max_ioctl = DRM_ARRAY_SIZE(i915_ioctls);
pci_set_power_state(dev->pdev, PCI_D3hot);
}
+ dev_priv->suspended = 1;
+
return 0;
}
struct drm_i915_private *dev_priv = dev->dev_private;
int ret = 0;
- pci_set_power_state(dev->pdev, PCI_D0);
- pci_restore_state(dev->pdev);
if (pci_enable_device(dev->pdev))
return -1;
pci_set_master(dev->pdev);
drm_helper_resume_force_mode(dev);
}
+ dev_priv->suspended = 0;
+
return ret;
}
+/**
+ * i965_reset - reset chip after a hang
+ * @dev: drm device to reset
+ * @flags: reset domains
+ *
+ * Reset the chip. Useful if a hang is detected. Returns zero on successful
+ * reset or otherwise an error code.
+ *
+ * Procedure is fairly simple:
+ * - reset the chip using the reset reg
+ * - re-init context state
+ * - re-init hardware status page
+ * - re-init ring buffer
+ * - re-init interrupt state
+ * - re-init display
+ */
+int i965_reset(struct drm_device *dev, u8 flags)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ unsigned long timeout;
+ u8 gdrst;
+ /*
+ * We really should only reset the display subsystem if we actually
+ * need to
+ */
+ bool need_display = true;
+
+ mutex_lock(&dev->struct_mutex);
+
+ /*
+ * Clear request list
+ */
+ i915_gem_retire_requests(dev);
+
+ if (need_display)
+ i915_save_display(dev);
+
+ if (IS_I965G(dev) || IS_G4X(dev)) {
+ /*
+ * Set the domains we want to reset, then the reset bit (bit 0).
+ * Clear the reset bit after a while and wait for hardware status
+ * bit (bit 1) to be set
+ */
+ pci_read_config_byte(dev->pdev, GDRST, &gdrst);
+ pci_write_config_byte(dev->pdev, GDRST, gdrst | flags | ((flags == GDRST_FULL) ? 0x1 : 0x0));
+ udelay(50);
+ pci_write_config_byte(dev->pdev, GDRST, gdrst & 0xfe);
+
+ /* ...we don't want to loop forever though, 500ms should be plenty */
+ timeout = jiffies + msecs_to_jiffies(500);
+ do {
+ udelay(100);
+ pci_read_config_byte(dev->pdev, GDRST, &gdrst);
+ } while ((gdrst & 0x1) && time_after(timeout, jiffies));
+
+ if (gdrst & 0x1) {
+ WARN(true, "i915: Failed to reset chip\n");
+ mutex_unlock(&dev->struct_mutex);
+ return -EIO;
+ }
+ } else {
+ DRM_ERROR("Error occurred. Don't know how to reset this chip.\n");
+ return -ENODEV;
+ }
+
+ /* Ok, now get things going again... */
+
+ /*
+ * Everything depends on having the GTT running, so we need to start
+ * there. Fortunately we don't need to do this unless we reset the
+ * chip at a PCI level.
+ *
+ * Next we need to restore the context, but we don't use those
+ * yet either...
+ *
+ * Ring buffer needs to be re-initialized in the KMS case, or if X
+ * was running at the time of the reset (i.e. we weren't VT
+ * switched away).
+ */
+ if (drm_core_check_feature(dev, DRIVER_MODESET) ||
+ !dev_priv->mm.suspended) {
+ drm_i915_ring_buffer_t *ring = &dev_priv->ring;
+ struct drm_gem_object *obj = ring->ring_obj;
+ struct drm_i915_gem_object *obj_priv = obj->driver_private;
+ dev_priv->mm.suspended = 0;
+
+ /* Stop the ring if it's running. */
+ I915_WRITE(PRB0_CTL, 0);
+ I915_WRITE(PRB0_TAIL, 0);
+ I915_WRITE(PRB0_HEAD, 0);
+
+ /* Initialize the ring. */
+ I915_WRITE(PRB0_START, obj_priv->gtt_offset);
+ I915_WRITE(PRB0_CTL,
+ ((obj->size - 4096) & RING_NR_PAGES) |
+ RING_NO_REPORT |
+ RING_VALID);
+ if (!drm_core_check_feature(dev, DRIVER_MODESET))
+ i915_kernel_lost_context(dev);
+ else {
+ ring->head = I915_READ(PRB0_HEAD) & HEAD_ADDR;
+ ring->tail = I915_READ(PRB0_TAIL) & TAIL_ADDR;
+ ring->space = ring->head - (ring->tail + 8);
+ if (ring->space < 0)
+ ring->space += ring->Size;
+ }
+
+ mutex_unlock(&dev->struct_mutex);
+ drm_irq_uninstall(dev);
+ drm_irq_install(dev);
+ mutex_lock(&dev->struct_mutex);
+ }
+
+ /*
+ * Display needs restore too...
+ */
+ if (need_display)
+ i915_restore_display(dev);
+
+ mutex_unlock(&dev->struct_mutex);
+ return 0;
+}
+
+
static int __devinit
i915_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
{
driver.num_ioctls = i915_max_ioctl;
+ i915_gem_shrinker_init();
+
/*
* If CONFIG_DRM_I915_KMS is set, default to KMS unless
* explicitly disabled with the module pararmeter.
static void __exit i915_exit(void)
{
+ i915_gem_shrinker_exit();
drm_exit(&driver);
}
PIPE_B,
};
+enum plane {
+ PLANE_A = 0,
+ PLANE_B,
+};
+
#define I915_NUM_PIPE 2
/* Interface history:
struct timeval time;
};
+struct drm_i915_display_funcs {
+ void (*dpms)(struct drm_crtc *crtc, int mode);
+ bool (*fbc_enabled)(struct drm_crtc *crtc);
+ void (*enable_fbc)(struct drm_crtc *crtc, unsigned long interval);
+ void (*disable_fbc)(struct drm_device *dev);
+ int (*get_display_clock_speed)(struct drm_device *dev);
+ int (*get_fifo_size)(struct drm_device *dev, int plane);
+ void (*update_wm)(struct drm_device *dev, int planea_clock,
+ int planeb_clock, int sr_hdisplay, int pixel_size);
+ /* clock updates for mode set */
+ /* cursor updates */
+ /* render clock increase/decrease */
+ /* display clock increase/decrease */
+ /* pll clock increase/decrease */
+ /* clock gating init */
+};
+
typedef struct drm_i915_private {
struct drm_device *dev;
unsigned int sr01, adpa, ppcr, dvob, dvoc, lvds;
int vblank_pipe;
+ /* For hangcheck timer */
+#define DRM_I915_HANGCHECK_PERIOD 75 /* in jiffies */
+ struct timer_list hangcheck_timer;
+ int hangcheck_count;
+ uint32_t last_acthd;
+
bool cursor_needs_physical;
struct drm_mm vram;
+ unsigned long cfb_size;
+ unsigned long cfb_pitch;
+ int cfb_fence;
+ int cfb_plane;
+
int irq_enabled;
struct intel_opregion opregion;
unsigned int edp_support:1;
int lvds_ssc_freq;
+ struct notifier_block lid_notifier;
+
int crt_ddc_bus; /* -1 = unknown, else GPIO to use for CRT DDC */
struct drm_i915_fence_reg fence_regs[16]; /* assume 965 */
int fence_reg_start; /* 4 if userland hasn't ioctl'd us yet */
struct work_struct error_work;
struct workqueue_struct *wq;
+ /* Display functions */
+ struct drm_i915_display_funcs display;
+
/* Register state */
+ bool suspended;
u8 saveLBB;
u32 saveDSPACNTR;
u32 saveDSPBCNTR;
struct io_mapping *gtt_mapping;
int gtt_mtrr;
+ /**
+ * Membership on list of all loaded devices, used to evict
+ * inactive buffers under memory pressure.
+ *
+ * Modifications should only be done whilst holding the
+ * shrink_list_lock spinlock.
+ */
+ struct list_head shrink_list;
+
/**
* List of objects currently involved in rendering from the
* ringbuffer.
* It prevents command submission from occuring and makes
* every pending request fail
*/
- int wedged;
+ atomic_t wedged;
/** Bit 6 swizzling required for X tiling */
uint32_t bit_6_swizzle_x;
* This is the same as gtt_space->start
*/
uint32_t gtt_offset;
- /**
- * Required alignment for the object
- */
- uint32_t gtt_alignment;
+
/**
* Fake offset for use by mmap(2)
*/
* in an execbuffer object list.
*/
int in_execbuffer;
+
+ /**
+ * Advice: are the backing pages purgeable?
+ */
+ int madv;
};
/**
extern unsigned int i915_fbpercrtc;
extern unsigned int i915_powersave;
+extern void i915_save_display(struct drm_device *dev);
+extern void i915_restore_display(struct drm_device *dev);
extern int i915_master_create(struct drm_device *dev, struct drm_master *master);
extern void i915_master_destroy(struct drm_device *dev, struct drm_master *master);
extern int i915_emit_box(struct drm_device *dev,
struct drm_clip_rect *boxes,
int i, int DR1, int DR4);
+extern int i965_reset(struct drm_device *dev, u8 flags);
/* i915_irq.c */
+void i915_hangcheck_elapsed(unsigned long data);
extern int i915_irq_emit(struct drm_device *dev, void *data,
struct drm_file *file_priv);
extern int i915_irq_wait(struct drm_device *dev, void *data,
struct drm_file *file_priv);
int i915_gem_throttle_ioctl(struct drm_device *dev, void *data,
struct drm_file *file_priv);
+int i915_gem_madvise_ioctl(struct drm_device *dev, void *data,
+ struct drm_file *file_priv);
int i915_gem_entervt_ioctl(struct drm_device *dev, void *data,
struct drm_file *file_priv);
int i915_gem_leavevt_ioctl(struct drm_device *dev, void *data,
void i915_gem_release_mmap(struct drm_gem_object *obj);
void i915_gem_lastclose(struct drm_device *dev);
uint32_t i915_get_gem_seqno(struct drm_device *dev);
+bool i915_seqno_passed(uint32_t seq1, uint32_t seq2);
int i915_gem_object_get_fence_reg(struct drm_gem_object *obj);
int i915_gem_object_put_fence_reg(struct drm_gem_object *obj);
void i915_gem_retire_requests(struct drm_device *dev);
void i915_gem_object_put_pages(struct drm_gem_object *obj);
void i915_gem_release(struct drm_device * dev, struct drm_file *file_priv);
+void i915_gem_shrinker_init(void);
+void i915_gem_shrinker_exit(void);
+
/* i915_gem_tiling.c */
void i915_gem_detect_bit_6_swizzle(struct drm_device *dev);
void i915_gem_object_do_bit_17_swizzle(struct drm_gem_object *obj);
extern void intel_modeset_init(struct drm_device *dev);
extern void intel_modeset_cleanup(struct drm_device *dev);
extern int intel_modeset_vga_set_state(struct drm_device *dev, bool state);
+extern void i8xx_disable_fbc(struct drm_device *dev);
+extern void g4x_disable_fbc(struct drm_device *dev);
/**
* Lock test for when it's just for synchronization of ring access.
(dev)->pci_device == 0x2E12 || \
(dev)->pci_device == 0x2E22 || \
(dev)->pci_device == 0x2E32 || \
+ (dev)->pci_device == 0x2E42 || \
(dev)->pci_device == 0x0042 || \
(dev)->pci_device == 0x0046)
(dev)->pci_device == 0x2E12 || \
(dev)->pci_device == 0x2E22 || \
(dev)->pci_device == 0x2E32 || \
+ (dev)->pci_device == 0x2E42 || \
IS_GM45(dev))
#define IS_IGDG(dev) ((dev)->pci_device == 0xa001)
#define SUPPORTS_INTEGRATED_HDMI(dev) (IS_G4X(dev) || IS_IGDNG(dev))
#define SUPPORTS_INTEGRATED_DP(dev) (IS_G4X(dev) || IS_IGDNG(dev))
#define SUPPORTS_EDP(dev) (IS_IGDNG_M(dev))
-#define I915_HAS_HOTPLUG(dev) (IS_I945G(dev) || IS_I945GM(dev) || IS_I965G(dev))
+#define I915_HAS_HOTPLUG(dev) (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev) || IS_I965G(dev))
/* dsparb controlled by hw only */
#define DSPARB_HWCONTROL(dev) (IS_G4X(dev) || IS_IGDNG(dev))
#define HAS_FW_BLC(dev) (IS_I9XX(dev) || IS_G4X(dev) || IS_IGDNG(dev))
#define HAS_PIPE_CXSR(dev) (IS_G4X(dev) || IS_IGDNG(dev))
+#define I915_HAS_FBC(dev) (IS_MOBILE(dev) && (IS_I9XX(dev) || IS_I965G(dev)))
#define PRIMARY_RINGBUFFER_SIZE (128*1024)
#include "drm.h"
#include "i915_drm.h"
#include "i915_drv.h"
+#include "i915_trace.h"
#include "intel_drv.h"
#include <linux/swap.h>
#include <linux/pci.h>
static int i915_gem_object_bind_to_gtt(struct drm_gem_object *obj,
unsigned alignment);
static void i915_gem_clear_fence_reg(struct drm_gem_object *obj);
-static int i915_gem_evict_something(struct drm_device *dev);
+static int i915_gem_evict_something(struct drm_device *dev, int min_size);
+static int i915_gem_evict_from_inactive_list(struct drm_device *dev);
static int i915_gem_phys_pwrite(struct drm_device *dev, struct drm_gem_object *obj,
struct drm_i915_gem_pwrite *args,
struct drm_file *file_priv);
+static LIST_HEAD(shrink_list);
+static DEFINE_SPINLOCK(shrink_list_lock);
+
int i915_gem_do_init(struct drm_device *dev, unsigned long start,
unsigned long end)
{
return ret;
}
+static inline gfp_t
+i915_gem_object_get_page_gfp_mask (struct drm_gem_object *obj)
+{
+ return mapping_gfp_mask(obj->filp->f_path.dentry->d_inode->i_mapping);
+}
+
+static inline void
+i915_gem_object_set_page_gfp_mask (struct drm_gem_object *obj, gfp_t gfp)
+{
+ mapping_set_gfp_mask(obj->filp->f_path.dentry->d_inode->i_mapping, gfp);
+}
+
+static int
+i915_gem_object_get_pages_or_evict(struct drm_gem_object *obj)
+{
+ int ret;
+
+ ret = i915_gem_object_get_pages(obj);
+
+ /* If we've insufficient memory to map in the pages, attempt
+ * to make some space by throwing out some old buffers.
+ */
+ if (ret == -ENOMEM) {
+ struct drm_device *dev = obj->dev;
+ gfp_t gfp;
+
+ ret = i915_gem_evict_something(dev, obj->size);
+ if (ret)
+ return ret;
+
+ gfp = i915_gem_object_get_page_gfp_mask(obj);
+ i915_gem_object_set_page_gfp_mask(obj, gfp & ~__GFP_NORETRY);
+ ret = i915_gem_object_get_pages(obj);
+ i915_gem_object_set_page_gfp_mask (obj, gfp);
+ }
+
+ return ret;
+}
+
/**
* This is the fallback shmem pread path, which allocates temporary storage
* in kernel space to copy_to_user into outside of the struct_mutex, so we
mutex_lock(&dev->struct_mutex);
- ret = i915_gem_object_get_pages(obj);
- if (ret != 0)
+ ret = i915_gem_object_get_pages_or_evict(obj);
+ if (ret)
goto fail_unlock;
ret = i915_gem_object_set_cpu_read_domain_range(obj, args->offset,
mutex_lock(&dev->struct_mutex);
- ret = i915_gem_object_get_pages(obj);
- if (ret != 0)
+ ret = i915_gem_object_get_pages_or_evict(obj);
+ if (ret)
goto fail_unlock;
ret = i915_gem_object_set_to_cpu_domain(obj, 1);
/* Now bind it into the GTT if needed */
mutex_lock(&dev->struct_mutex);
if (!obj_priv->gtt_space) {
- ret = i915_gem_object_bind_to_gtt(obj, obj_priv->gtt_alignment);
- if (ret) {
- mutex_unlock(&dev->struct_mutex);
- return VM_FAULT_SIGBUS;
- }
-
- ret = i915_gem_object_set_to_gtt_domain(obj, write);
- if (ret) {
- mutex_unlock(&dev->struct_mutex);
- return VM_FAULT_SIGBUS;
- }
+ ret = i915_gem_object_bind_to_gtt(obj, 0);
+ if (ret)
+ goto unlock;
list_add_tail(&obj_priv->list, &dev_priv->mm.inactive_list);
+
+ ret = i915_gem_object_set_to_gtt_domain(obj, write);
+ if (ret)
+ goto unlock;
}
/* Need a new fence register? */
if (obj_priv->tiling_mode != I915_TILING_NONE) {
ret = i915_gem_object_get_fence_reg(obj);
- if (ret) {
- mutex_unlock(&dev->struct_mutex);
- return VM_FAULT_SIGBUS;
- }
+ if (ret)
+ goto unlock;
}
pfn = ((dev->agp->base + obj_priv->gtt_offset) >> PAGE_SHIFT) +
/* Finally, remap it using the new GTT offset */
ret = vm_insert_pfn(vma, (unsigned long)vmf->virtual_address, pfn);
-
+unlock:
mutex_unlock(&dev->struct_mutex);
switch (ret) {
+ case 0:
+ case -ERESTARTSYS:
+ return VM_FAULT_NOPAGE;
case -ENOMEM:
case -EAGAIN:
return VM_FAULT_OOM;
- case -EFAULT:
- case -EINVAL:
- return VM_FAULT_SIGBUS;
default:
- return VM_FAULT_NOPAGE;
+ return VM_FAULT_SIGBUS;
}
}
obj_priv = obj->driver_private;
+ if (obj_priv->madv != I915_MADV_WILLNEED) {
+ DRM_ERROR("Attempting to mmap a purgeable buffer\n");
+ drm_gem_object_unreference(obj);
+ mutex_unlock(&dev->struct_mutex);
+ return -EINVAL;
+ }
+
+
if (!obj_priv->mmap_offset) {
ret = i915_gem_create_mmap_offset(obj);
if (ret) {
args->offset = obj_priv->mmap_offset;
- obj_priv->gtt_alignment = i915_gem_get_gtt_alignment(obj);
-
- /* Make sure the alignment is correct for fence regs etc */
- if (obj_priv->agp_mem &&
- (obj_priv->gtt_offset & (obj_priv->gtt_alignment - 1))) {
- drm_gem_object_unreference(obj);
- mutex_unlock(&dev->struct_mutex);
- return -EINVAL;
- }
-
/*
* Pull it into the GTT so that we have a page list (makes the
* initial fault faster and any subsequent flushing possible).
*/
if (!obj_priv->agp_mem) {
- ret = i915_gem_object_bind_to_gtt(obj, obj_priv->gtt_alignment);
+ ret = i915_gem_object_bind_to_gtt(obj, 0);
if (ret) {
drm_gem_object_unreference(obj);
mutex_unlock(&dev->struct_mutex);
int i;
BUG_ON(obj_priv->pages_refcount == 0);
+ BUG_ON(obj_priv->madv == __I915_MADV_PURGED);
if (--obj_priv->pages_refcount != 0)
return;
if (obj_priv->tiling_mode != I915_TILING_NONE)
i915_gem_object_save_bit_17_swizzle(obj);
- for (i = 0; i < page_count; i++)
- if (obj_priv->pages[i] != NULL) {
- if (obj_priv->dirty)
- set_page_dirty(obj_priv->pages[i]);
+ if (obj_priv->madv == I915_MADV_DONTNEED)
+ obj_priv->dirty = 0;
+
+ for (i = 0; i < page_count; i++) {
+ if (obj_priv->pages[i] == NULL)
+ break;
+
+ if (obj_priv->dirty)
+ set_page_dirty(obj_priv->pages[i]);
+
+ if (obj_priv->madv == I915_MADV_WILLNEED)
mark_page_accessed(obj_priv->pages[i]);
- page_cache_release(obj_priv->pages[i]);
- }
+
+ page_cache_release(obj_priv->pages[i]);
+ }
obj_priv->dirty = 0;
drm_free_large(obj_priv->pages);
obj_priv->last_rendering_seqno = 0;
}
+/* Immediately discard the backing storage */
+static void
+i915_gem_object_truncate(struct drm_gem_object *obj)
+{
+ struct drm_i915_gem_object *obj_priv = obj->driver_private;
+ struct inode *inode;
+
+ inode = obj->filp->f_path.dentry->d_inode;
+ if (inode->i_op->truncate)
+ inode->i_op->truncate (inode);
+
+ obj_priv->madv = __I915_MADV_PURGED;
+}
+
+static inline int
+i915_gem_object_is_purgeable(struct drm_i915_gem_object *obj_priv)
+{
+ return obj_priv->madv == I915_MADV_DONTNEED;
+}
+
static void
i915_gem_object_move_to_inactive(struct drm_gem_object *obj)
{
if ((obj->write_domain & flush_domains) ==
obj->write_domain) {
+ uint32_t old_write_domain = obj->write_domain;
+
obj->write_domain = 0;
i915_gem_object_move_to_active(obj, seqno);
+
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
}
}
- if (was_empty && !dev_priv->mm.suspended)
- queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ);
+ if (!dev_priv->mm.suspended) {
+ mod_timer(&dev_priv->hangcheck_timer, jiffies + DRM_I915_HANGCHECK_PERIOD);
+ if (was_empty)
+ queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, HZ);
+ }
return seqno;
}
{
drm_i915_private_t *dev_priv = dev->dev_private;
+ trace_i915_gem_request_retire(dev, request->seqno);
+
/* Move any buffers on the active list that are no longer referenced
* by the ringbuffer to the flushing/inactive lists as appropriate.
*/
/**
* Returns true if seq1 is later than seq2.
*/
-static int
+bool
i915_seqno_passed(uint32_t seq1, uint32_t seq2)
{
return (int32_t)(seq1 - seq2) >= 0;
retiring_seqno = request->seqno;
if (i915_seqno_passed(seqno, retiring_seqno) ||
- dev_priv->mm.wedged) {
+ atomic_read(&dev_priv->mm.wedged)) {
i915_gem_retire_request(dev, request);
list_del(&request->list);
BUG_ON(seqno == 0);
+ if (atomic_read(&dev_priv->mm.wedged))
+ return -EIO;
+
if (!i915_seqno_passed(i915_get_gem_seqno(dev), seqno)) {
if (IS_IGDNG(dev))
ier = I915_READ(DEIER) | I915_READ(GTIER);
i915_driver_irq_postinstall(dev);
}
+ trace_i915_gem_request_wait_begin(dev, seqno);
+
dev_priv->mm.waiting_gem_seqno = seqno;
i915_user_irq_get(dev);
ret = wait_event_interruptible(dev_priv->irq_queue,
i915_seqno_passed(i915_get_gem_seqno(dev),
seqno) ||
- dev_priv->mm.wedged);
+ atomic_read(&dev_priv->mm.wedged));
i915_user_irq_put(dev);
dev_priv->mm.waiting_gem_seqno = 0;
+
+ trace_i915_gem_request_wait_end(dev, seqno);
}
- if (dev_priv->mm.wedged)
+ if (atomic_read(&dev_priv->mm.wedged))
ret = -EIO;
if (ret && ret != -ERESTARTSYS)
DRM_INFO("%s: invalidate %08x flush %08x\n", __func__,
invalidate_domains, flush_domains);
#endif
+ trace_i915_gem_request_flush(dev, dev_priv->mm.next_gem_seqno,
+ invalidate_domains, flush_domains);
if (flush_domains & I915_GEM_DOMAIN_CPU)
drm_agp_chipset_flush(dev);
return -EINVAL;
}
+ /* blow away mappings if mapped through GTT */
+ i915_gem_release_mmap(obj);
+
+ if (obj_priv->fence_reg != I915_FENCE_REG_NONE)
+ i915_gem_clear_fence_reg(obj);
+
/* Move the object to the CPU domain to ensure that
* any possible CPU writes while it's not in the GTT
* are flushed when we go to remap it. This will
return ret;
}
+ BUG_ON(obj_priv->active);
+
if (obj_priv->agp_mem != NULL) {
drm_unbind_agp(obj_priv->agp_mem);
drm_free_agp(obj_priv->agp_mem, obj->size / PAGE_SIZE);
obj_priv->agp_mem = NULL;
}
- BUG_ON(obj_priv->active);
-
- /* blow away mappings if mapped through GTT */
- i915_gem_release_mmap(obj);
-
- if (obj_priv->fence_reg != I915_FENCE_REG_NONE)
- i915_gem_clear_fence_reg(obj);
-
i915_gem_object_put_pages(obj);
+ BUG_ON(obj_priv->pages_refcount);
if (obj_priv->gtt_space) {
atomic_dec(&dev->gtt_count);
if (!list_empty(&obj_priv->list))
list_del_init(&obj_priv->list);
+ if (i915_gem_object_is_purgeable(obj_priv))
+ i915_gem_object_truncate(obj);
+
+ trace_i915_gem_object_unbind(obj);
+
return 0;
}
+static struct drm_gem_object *
+i915_gem_find_inactive_object(struct drm_device *dev, int min_size)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ struct drm_i915_gem_object *obj_priv;
+ struct drm_gem_object *best = NULL;
+ struct drm_gem_object *first = NULL;
+
+ /* Try to find the smallest clean object */
+ list_for_each_entry(obj_priv, &dev_priv->mm.inactive_list, list) {
+ struct drm_gem_object *obj = obj_priv->obj;
+ if (obj->size >= min_size) {
+ if ((!obj_priv->dirty ||
+ i915_gem_object_is_purgeable(obj_priv)) &&
+ (!best || obj->size < best->size)) {
+ best = obj;
+ if (best->size == min_size)
+ return best;
+ }
+ if (!first)
+ first = obj;
+ }
+ }
+
+ return best ? best : first;
+}
+
static int
-i915_gem_evict_something(struct drm_device *dev)
+i915_gem_evict_everything(struct drm_device *dev)
+{
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ uint32_t seqno;
+ int ret;
+ bool lists_empty;
+
+ spin_lock(&dev_priv->mm.active_list_lock);
+ lists_empty = (list_empty(&dev_priv->mm.inactive_list) &&
+ list_empty(&dev_priv->mm.flushing_list) &&
+ list_empty(&dev_priv->mm.active_list));
+ spin_unlock(&dev_priv->mm.active_list_lock);
+
+ if (lists_empty)
+ return -ENOSPC;
+
+ /* Flush everything (on to the inactive lists) and evict */
+ i915_gem_flush(dev, I915_GEM_GPU_DOMAINS, I915_GEM_GPU_DOMAINS);
+ seqno = i915_add_request(dev, NULL, I915_GEM_GPU_DOMAINS);
+ if (seqno == 0)
+ return -ENOMEM;
+
+ ret = i915_wait_request(dev, seqno);
+ if (ret)
+ return ret;
+
+ ret = i915_gem_evict_from_inactive_list(dev);
+ if (ret)
+ return ret;
+
+ spin_lock(&dev_priv->mm.active_list_lock);
+ lists_empty = (list_empty(&dev_priv->mm.inactive_list) &&
+ list_empty(&dev_priv->mm.flushing_list) &&
+ list_empty(&dev_priv->mm.active_list));
+ spin_unlock(&dev_priv->mm.active_list_lock);
+ BUG_ON(!lists_empty);
+
+ return 0;
+}
+
+static int
+i915_gem_evict_something(struct drm_device *dev, int min_size)
{
drm_i915_private_t *dev_priv = dev->dev_private;
struct drm_gem_object *obj;
- struct drm_i915_gem_object *obj_priv;
- int ret = 0;
+ int ret;
for (;;) {
+ i915_gem_retire_requests(dev);
+
/* If there's an inactive buffer available now, grab it
* and be done.
*/
- if (!list_empty(&dev_priv->mm.inactive_list)) {
- obj_priv = list_first_entry(&dev_priv->mm.inactive_list,
- struct drm_i915_gem_object,
- list);
- obj = obj_priv->obj;
- BUG_ON(obj_priv->pin_count != 0);
+ obj = i915_gem_find_inactive_object(dev, min_size);
+ if (obj) {
+ struct drm_i915_gem_object *obj_priv;
+
#if WATCH_LRU
DRM_INFO("%s: evicting %p\n", __func__, obj);
#endif
+ obj_priv = obj->driver_private;
+ BUG_ON(obj_priv->pin_count != 0);
BUG_ON(obj_priv->active);
/* Wait on the rendering and unbind the buffer. */
- ret = i915_gem_object_unbind(obj);
- break;
+ return i915_gem_object_unbind(obj);
}
/* If we didn't get anything, but the ring is still processing
- * things, wait for one of those things to finish and hopefully
- * leave us a buffer to evict.
+ * things, wait for the next to finish and hopefully leave us
+ * a buffer to evict.
*/
if (!list_empty(&dev_priv->mm.request_list)) {
struct drm_i915_gem_request *request;
ret = i915_wait_request(dev, request->seqno);
if (ret)
- break;
+ return ret;
- /* if waiting caused an object to become inactive,
- * then loop around and wait for it. Otherwise, we
- * assume that waiting freed and unbound something,
- * so there should now be some space in the GTT
- */
- if (!list_empty(&dev_priv->mm.inactive_list))
- continue;
- break;
+ continue;
}
/* If we didn't have anything on the request list but there
* will get moved to inactive.
*/
if (!list_empty(&dev_priv->mm.flushing_list)) {
- obj_priv = list_first_entry(&dev_priv->mm.flushing_list,
- struct drm_i915_gem_object,
- list);
- obj = obj_priv->obj;
+ struct drm_i915_gem_object *obj_priv;
- i915_gem_flush(dev,
- obj->write_domain,
- obj->write_domain);
- i915_add_request(dev, NULL, obj->write_domain);
+ /* Find an object that we can immediately reuse */
+ list_for_each_entry(obj_priv, &dev_priv->mm.flushing_list, list) {
+ obj = obj_priv->obj;
+ if (obj->size >= min_size)
+ break;
- obj = NULL;
- continue;
- }
+ obj = NULL;
+ }
- DRM_ERROR("inactive empty %d request empty %d "
- "flushing empty %d\n",
- list_empty(&dev_priv->mm.inactive_list),
- list_empty(&dev_priv->mm.request_list),
- list_empty(&dev_priv->mm.flushing_list));
- /* If we didn't do any of the above, there's nothing to be done
- * and we just can't fit it in.
- */
- return -ENOSPC;
- }
- return ret;
-}
+ if (obj != NULL) {
+ uint32_t seqno;
-static int
-i915_gem_evict_everything(struct drm_device *dev)
-{
- int ret;
+ i915_gem_flush(dev,
+ obj->write_domain,
+ obj->write_domain);
+ seqno = i915_add_request(dev, NULL, obj->write_domain);
+ if (seqno == 0)
+ return -ENOMEM;
- for (;;) {
- ret = i915_gem_evict_something(dev);
- if (ret != 0)
- break;
+ ret = i915_wait_request(dev, seqno);
+ if (ret)
+ return ret;
+
+ continue;
+ }
+ }
+
+ /* If we didn't do any of the above, there's no single buffer
+ * large enough to swap out for the new one, so just evict
+ * everything and start again. (This should be rare.)
+ */
+ if (!list_empty (&dev_priv->mm.inactive_list))
+ return i915_gem_evict_from_inactive_list(dev);
+ else
+ return i915_gem_evict_everything(dev);
}
- if (ret == -ENOSPC)
- return 0;
- return ret;
}
int
BUG_ON(obj_priv->pages != NULL);
obj_priv->pages = drm_calloc_large(page_count, sizeof(struct page *));
if (obj_priv->pages == NULL) {
- DRM_ERROR("Faled to allocate page list\n");
obj_priv->pages_refcount--;
return -ENOMEM;
}
page = read_mapping_page(mapping, i, NULL);
if (IS_ERR(page)) {
ret = PTR_ERR(page);
- DRM_ERROR("read_mapping_page failed: %d\n", ret);
i915_gem_object_put_pages(obj);
return ret;
}
else
i830_write_fence_reg(reg);
+ trace_i915_gem_object_get_fence(obj, i, obj_priv->tiling_mode);
+
return 0;
}
drm_i915_private_t *dev_priv = dev->dev_private;
struct drm_i915_gem_object *obj_priv = obj->driver_private;
struct drm_mm_node *free_space;
- int page_count, ret;
+ bool retry_alloc = false;
+ int ret;
if (dev_priv->mm.suspended)
return -EBUSY;
+
+ if (obj_priv->madv != I915_MADV_WILLNEED) {
+ DRM_ERROR("Attempting to bind a purgeable object\n");
+ return -EINVAL;
+ }
+
if (alignment == 0)
alignment = i915_gem_get_gtt_alignment(obj);
if (alignment & (i915_gem_get_gtt_alignment(obj) - 1)) {
}
}
if (obj_priv->gtt_space == NULL) {
- bool lists_empty;
-
/* If the gtt is empty and we're still having trouble
* fitting our object in, we're out of memory.
*/
#if WATCH_LRU
DRM_INFO("%s: GTT full, evicting something\n", __func__);
#endif
- spin_lock(&dev_priv->mm.active_list_lock);
- lists_empty = (list_empty(&dev_priv->mm.inactive_list) &&
- list_empty(&dev_priv->mm.flushing_list) &&
- list_empty(&dev_priv->mm.active_list));
- spin_unlock(&dev_priv->mm.active_list_lock);
- if (lists_empty) {
- DRM_ERROR("GTT full, but LRU list empty\n");
- return -ENOSPC;
- }
-
- ret = i915_gem_evict_something(dev);
- if (ret != 0) {
- if (ret != -ERESTARTSYS)
- DRM_ERROR("Failed to evict a buffer %d\n", ret);
+ ret = i915_gem_evict_something(dev, obj->size);
+ if (ret)
return ret;
- }
+
goto search_free;
}
DRM_INFO("Binding object of size %zd at 0x%08x\n",
obj->size, obj_priv->gtt_offset);
#endif
+ if (retry_alloc) {
+ i915_gem_object_set_page_gfp_mask (obj,
+ i915_gem_object_get_page_gfp_mask (obj) & ~__GFP_NORETRY);
+ }
ret = i915_gem_object_get_pages(obj);
+ if (retry_alloc) {
+ i915_gem_object_set_page_gfp_mask (obj,
+ i915_gem_object_get_page_gfp_mask (obj) | __GFP_NORETRY);
+ }
if (ret) {
drm_mm_put_block(obj_priv->gtt_space);
obj_priv->gtt_space = NULL;
+
+ if (ret == -ENOMEM) {
+ /* first try to clear up some space from the GTT */
+ ret = i915_gem_evict_something(dev, obj->size);
+ if (ret) {
+ /* now try to shrink everyone else */
+ if (! retry_alloc) {
+ retry_alloc = true;
+ goto search_free;
+ }
+
+ return ret;
+ }
+
+ goto search_free;
+ }
+
return ret;
}
- page_count = obj->size / PAGE_SIZE;
/* Create an AGP memory structure pointing at our pages, and bind it
* into the GTT.
*/
obj_priv->agp_mem = drm_agp_bind_pages(dev,
obj_priv->pages,
- page_count,
+ obj->size >> PAGE_SHIFT,
obj_priv->gtt_offset,
obj_priv->agp_type);
if (obj_priv->agp_mem == NULL) {
i915_gem_object_put_pages(obj);
drm_mm_put_block(obj_priv->gtt_space);
obj_priv->gtt_space = NULL;
- return -ENOMEM;
+
+ ret = i915_gem_evict_something(dev, obj->size);
+ if (ret)
+ return ret;
+
+ goto search_free;
}
atomic_inc(&dev->gtt_count);
atomic_add(obj->size, &dev->gtt_memory);
BUG_ON(obj->read_domains & I915_GEM_GPU_DOMAINS);
BUG_ON(obj->write_domain & I915_GEM_GPU_DOMAINS);
+ trace_i915_gem_object_bind(obj, obj_priv->gtt_offset);
+
return 0;
}
if (obj_priv->pages == NULL)
return;
- /* XXX: The 865 in particular appears to be weird in how it handles
- * cache flushing. We haven't figured it out, but the
- * clflush+agp_chipset_flush doesn't appear to successfully get the
- * data visible to the PGU, while wbinvd + agp_chipset_flush does.
- */
- if (IS_I865G(obj->dev)) {
- wbinvd();
- return;
- }
+ trace_i915_gem_object_clflush(obj);
drm_clflush_pages(obj_priv->pages, obj->size / PAGE_SIZE);
}
{
struct drm_device *dev = obj->dev;
uint32_t seqno;
+ uint32_t old_write_domain;
if ((obj->write_domain & I915_GEM_GPU_DOMAINS) == 0)
return;
/* Queue the GPU write cache flushing we need. */
+ old_write_domain = obj->write_domain;
i915_gem_flush(dev, 0, obj->write_domain);
seqno = i915_add_request(dev, NULL, obj->write_domain);
obj->write_domain = 0;
i915_gem_object_move_to_active(obj, seqno);
+
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
/** Flushes the GTT write domain for the object if it's dirty. */
static void
i915_gem_object_flush_gtt_write_domain(struct drm_gem_object *obj)
{
+ uint32_t old_write_domain;
+
if (obj->write_domain != I915_GEM_DOMAIN_GTT)
return;
* to it immediately go to main memory as far as we know, so there's
* no chipset flush. It also doesn't land in render cache.
*/
+ old_write_domain = obj->write_domain;
obj->write_domain = 0;
+
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
/** Flushes the CPU write domain for the object if it's dirty. */
i915_gem_object_flush_cpu_write_domain(struct drm_gem_object *obj)
{
struct drm_device *dev = obj->dev;
+ uint32_t old_write_domain;
if (obj->write_domain != I915_GEM_DOMAIN_CPU)
return;
i915_gem_clflush_object(obj);
drm_agp_chipset_flush(dev);
+ old_write_domain = obj->write_domain;
obj->write_domain = 0;
+
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
/**
i915_gem_object_set_to_gtt_domain(struct drm_gem_object *obj, int write)
{
struct drm_i915_gem_object *obj_priv = obj->driver_private;
+ uint32_t old_write_domain, old_read_domains;
int ret;
/* Not valid to be called on unbound objects. */
if (ret != 0)
return ret;
+ old_write_domain = obj->write_domain;
+ old_read_domains = obj->read_domains;
+
/* If we're writing through the GTT domain, then CPU and GPU caches
* will need to be invalidated at next use.
*/
obj_priv->dirty = 1;
}
+ trace_i915_gem_object_change_domain(obj,
+ old_read_domains,
+ old_write_domain);
+
return 0;
}
static int
i915_gem_object_set_to_cpu_domain(struct drm_gem_object *obj, int write)
{
+ uint32_t old_write_domain, old_read_domains;
int ret;
i915_gem_object_flush_gpu_write_domain(obj);
*/
i915_gem_object_set_to_full_cpu_read_domain(obj);
+ old_write_domain = obj->write_domain;
+ old_read_domains = obj->read_domains;
+
/* Flush the CPU cache if it's still invalid. */
if ((obj->read_domains & I915_GEM_DOMAIN_CPU) == 0) {
i915_gem_clflush_object(obj);
obj->write_domain = I915_GEM_DOMAIN_CPU;
}
+ trace_i915_gem_object_change_domain(obj,
+ old_read_domains,
+ old_write_domain);
+
return 0;
}
struct drm_i915_gem_object *obj_priv = obj->driver_private;
uint32_t invalidate_domains = 0;
uint32_t flush_domains = 0;
+ uint32_t old_read_domains;
BUG_ON(obj->pending_read_domains & I915_GEM_DOMAIN_CPU);
BUG_ON(obj->pending_write_domain == I915_GEM_DOMAIN_CPU);
i915_gem_clflush_object(obj);
}
+ old_read_domains = obj->read_domains;
+
/* The actual obj->write_domain will be updated with
* pending_write_domain after we emit the accumulated flush for all
* of our domain changes in execbuffers (which clears objects'
obj->read_domains, obj->write_domain,
dev->invalidate_domains, dev->flush_domains);
#endif
+
+ trace_i915_gem_object_change_domain(obj,
+ old_read_domains,
+ obj->write_domain);
}
/**
uint64_t offset, uint64_t size)
{
struct drm_i915_gem_object *obj_priv = obj->driver_private;
+ uint32_t old_read_domains;
int i, ret;
if (offset == 0 && size == obj->size)
*/
BUG_ON((obj->write_domain & ~I915_GEM_DOMAIN_CPU) != 0);
+ old_read_domains = obj->read_domains;
obj->read_domains |= I915_GEM_DOMAIN_CPU;
+ trace_i915_gem_object_change_domain(obj,
+ old_read_domains,
+ obj->write_domain);
+
return 0;
}
}
target_obj_priv = target_obj->driver_private;
+#if WATCH_RELOC
+ DRM_INFO("%s: obj %p offset %08x target %d "
+ "read %08x write %08x gtt %08x "
+ "presumed %08x delta %08x\n",
+ __func__,
+ obj,
+ (int) reloc->offset,
+ (int) reloc->target_handle,
+ (int) reloc->read_domains,
+ (int) reloc->write_domain,
+ (int) target_obj_priv->gtt_offset,
+ (int) reloc->presumed_offset,
+ reloc->delta);
+#endif
+
/* The target buffer should have appeared before us in the
* exec_object list, so it should have a GTT space bound by now.
*/
return -EINVAL;
}
- if (reloc->offset > obj->size - 4) {
- DRM_ERROR("Relocation beyond object bounds: "
- "obj %p target %d offset %d size %d.\n",
- obj, reloc->target_handle,
- (int) reloc->offset, (int) obj->size);
- drm_gem_object_unreference(target_obj);
- i915_gem_object_unpin(obj);
- return -EINVAL;
- }
- if (reloc->offset & 3) {
- DRM_ERROR("Relocation not 4-byte aligned: "
- "obj %p target %d offset %d.\n",
- obj, reloc->target_handle,
- (int) reloc->offset);
- drm_gem_object_unreference(target_obj);
- i915_gem_object_unpin(obj);
- return -EINVAL;
- }
-
+ /* Validate that the target is in a valid r/w GPU domain */
if (reloc->write_domain & I915_GEM_DOMAIN_CPU ||
reloc->read_domains & I915_GEM_DOMAIN_CPU) {
DRM_ERROR("reloc with read/write CPU domains: "
i915_gem_object_unpin(obj);
return -EINVAL;
}
-
if (reloc->write_domain && target_obj->pending_write_domain &&
reloc->write_domain != target_obj->pending_write_domain) {
DRM_ERROR("Write domain conflict: "
return -EINVAL;
}
-#if WATCH_RELOC
- DRM_INFO("%s: obj %p offset %08x target %d "
- "read %08x write %08x gtt %08x "
- "presumed %08x delta %08x\n",
- __func__,
- obj,
- (int) reloc->offset,
- (int) reloc->target_handle,
- (int) reloc->read_domains,
- (int) reloc->write_domain,
- (int) target_obj_priv->gtt_offset,
- (int) reloc->presumed_offset,
- reloc->delta);
-#endif
-
target_obj->pending_read_domains |= reloc->read_domains;
target_obj->pending_write_domain |= reloc->write_domain;
continue;
}
+ /* Check that the relocation address is valid... */
+ if (reloc->offset > obj->size - 4) {
+ DRM_ERROR("Relocation beyond object bounds: "
+ "obj %p target %d offset %d size %d.\n",
+ obj, reloc->target_handle,
+ (int) reloc->offset, (int) obj->size);
+ drm_gem_object_unreference(target_obj);
+ i915_gem_object_unpin(obj);
+ return -EINVAL;
+ }
+ if (reloc->offset & 3) {
+ DRM_ERROR("Relocation not 4-byte aligned: "
+ "obj %p target %d offset %d.\n",
+ obj, reloc->target_handle,
+ (int) reloc->offset);
+ drm_gem_object_unreference(target_obj);
+ i915_gem_object_unpin(obj);
+ return -EINVAL;
+ }
+
+ /* and points to somewhere within the target object. */
+ if (reloc->delta >= target_obj->size) {
+ DRM_ERROR("Relocation beyond target object bounds: "
+ "obj %p target %d delta %d size %d.\n",
+ obj, reloc->target_handle,
+ (int) reloc->delta, (int) target_obj->size);
+ drm_gem_object_unreference(target_obj);
+ i915_gem_object_unpin(obj);
+ return -EINVAL;
+ }
+
ret = i915_gem_object_set_to_gtt_domain(obj, 1);
if (ret != 0) {
drm_gem_object_unreference(target_obj);
exec_start = (uint32_t) exec_offset + exec->batch_start_offset;
exec_len = (uint32_t) exec->batch_len;
+ trace_i915_gem_request_submit(dev, dev_priv->mm.next_gem_seqno);
+
count = nbox ? nbox : 1;
for (i = 0; i < count; i++) {
i915_verify_inactive(dev, __FILE__, __LINE__);
- if (dev_priv->mm.wedged) {
+ if (atomic_read(&dev_priv->mm.wedged)) {
DRM_ERROR("Execbuf while wedged\n");
mutex_unlock(&dev->struct_mutex);
ret = -EIO;
/* error other than GTT full, or we've already tried again */
if (ret != -ENOSPC || pin_tries >= 1) {
- if (ret != -ERESTARTSYS)
- DRM_ERROR("Failed to pin buffers %d\n", ret);
+ if (ret != -ERESTARTSYS) {
+ unsigned long long total_size = 0;
+ for (i = 0; i < args->buffer_count; i++)
+ total_size += object_list[i]->size;
+ DRM_ERROR("Failed to pin buffer %d of %d, total %llu bytes: %d\n",
+ pinned+1, args->buffer_count,
+ total_size, ret);
+ DRM_ERROR("%d objects [%d pinned], "
+ "%d object bytes [%d pinned], "
+ "%d/%d gtt bytes\n",
+ atomic_read(&dev->object_count),
+ atomic_read(&dev->pin_count),
+ atomic_read(&dev->object_memory),
+ atomic_read(&dev->pin_memory),
+ atomic_read(&dev->gtt_memory),
+ dev->gtt_total);
+ }
goto err;
}
/* evict everyone we can from the aperture */
ret = i915_gem_evict_everything(dev);
- if (ret)
+ if (ret && ret != -ENOSPC)
goto err;
}
for (i = 0; i < args->buffer_count; i++) {
struct drm_gem_object *obj = object_list[i];
+ uint32_t old_write_domain = obj->write_domain;
obj->write_domain = obj->pending_write_domain;
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
i915_verify_inactive(dev, __FILE__, __LINE__);
i915_verify_inactive(dev, __FILE__, __LINE__);
if (obj_priv->gtt_space == NULL) {
ret = i915_gem_object_bind_to_gtt(obj, alignment);
- if (ret != 0) {
- if (ret != -EBUSY && ret != -ERESTARTSYS)
- DRM_ERROR("Failure to bind: %d\n", ret);
+ if (ret)
return ret;
- }
}
/*
* Pre-965 chips need a fence register set up in order to
}
obj_priv = obj->driver_private;
+ if (obj_priv->madv != I915_MADV_WILLNEED) {
+ DRM_ERROR("Attempting to pin a purgeable buffer\n");
+ drm_gem_object_unreference(obj);
+ mutex_unlock(&dev->struct_mutex);
+ return -EINVAL;
+ }
+
if (obj_priv->pin_filp != NULL && obj_priv->pin_filp != file_priv) {
DRM_ERROR("Already pinned in i915_gem_pin_ioctl(): %d\n",
args->handle);
return i915_gem_ring_throttle(dev, file_priv);
}
+int
+i915_gem_madvise_ioctl(struct drm_device *dev, void *data,
+ struct drm_file *file_priv)
+{
+ struct drm_i915_gem_madvise *args = data;
+ struct drm_gem_object *obj;
+ struct drm_i915_gem_object *obj_priv;
+
+ switch (args->madv) {
+ case I915_MADV_DONTNEED:
+ case I915_MADV_WILLNEED:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ obj = drm_gem_object_lookup(dev, file_priv, args->handle);
+ if (obj == NULL) {
+ DRM_ERROR("Bad handle in i915_gem_madvise_ioctl(): %d\n",
+ args->handle);
+ return -EBADF;
+ }
+
+ mutex_lock(&dev->struct_mutex);
+ obj_priv = obj->driver_private;
+
+ if (obj_priv->pin_count) {
+ drm_gem_object_unreference(obj);
+ mutex_unlock(&dev->struct_mutex);
+
+ DRM_ERROR("Attempted i915_gem_madvise_ioctl() on a pinned object\n");
+ return -EINVAL;
+ }
+
+ if (obj_priv->madv != __I915_MADV_PURGED)
+ obj_priv->madv = args->madv;
+
+ /* if the object is no longer bound, discard its backing storage */
+ if (i915_gem_object_is_purgeable(obj_priv) &&
+ obj_priv->gtt_space == NULL)
+ i915_gem_object_truncate(obj);
+
+ args->retained = obj_priv->madv != __I915_MADV_PURGED;
+
+ drm_gem_object_unreference(obj);
+ mutex_unlock(&dev->struct_mutex);
+
+ return 0;
+}
+
int i915_gem_init_object(struct drm_gem_object *obj)
{
struct drm_i915_gem_object *obj_priv;
obj_priv->fence_reg = I915_FENCE_REG_NONE;
INIT_LIST_HEAD(&obj_priv->list);
INIT_LIST_HEAD(&obj_priv->fence_list);
+ obj_priv->madv = I915_MADV_WILLNEED;
+
+ trace_i915_gem_object_create(obj);
return 0;
}
struct drm_device *dev = obj->dev;
struct drm_i915_gem_object *obj_priv = obj->driver_private;
+ trace_i915_gem_object_destroy(obj);
+
while (obj_priv->pin_count > 0)
i915_gem_object_unpin(obj);
i915_gem_object_unbind(obj);
- i915_gem_free_mmap_offset(obj);
+ if (obj_priv->mmap_offset)
+ i915_gem_free_mmap_offset(obj);
kfree(obj_priv->page_cpu_valid);
kfree(obj_priv->bit_17);
kfree(obj->driver_private);
}
-/** Unbinds all objects that are on the given buffer list. */
+/** Unbinds all inactive objects. */
static int
-i915_gem_evict_from_list(struct drm_device *dev, struct list_head *head)
+i915_gem_evict_from_inactive_list(struct drm_device *dev)
{
- struct drm_gem_object *obj;
- struct drm_i915_gem_object *obj_priv;
- int ret;
+ drm_i915_private_t *dev_priv = dev->dev_private;
- while (!list_empty(head)) {
- obj_priv = list_first_entry(head,
- struct drm_i915_gem_object,
- list);
- obj = obj_priv->obj;
+ while (!list_empty(&dev_priv->mm.inactive_list)) {
+ struct drm_gem_object *obj;
+ int ret;
- if (obj_priv->pin_count != 0) {
- DRM_ERROR("Pinned object in unbind list\n");
- mutex_unlock(&dev->struct_mutex);
- return -EINVAL;
- }
+ obj = list_first_entry(&dev_priv->mm.inactive_list,
+ struct drm_i915_gem_object,
+ list)->obj;
ret = i915_gem_object_unbind(obj);
if (ret != 0) {
- DRM_ERROR("Error unbinding object in LeaveVT: %d\n",
- ret);
- mutex_unlock(&dev->struct_mutex);
+ DRM_ERROR("Error unbinding object: %d\n", ret);
return ret;
}
}
-
return 0;
}
* We need to replace this with a semaphore, or something.
*/
dev_priv->mm.suspended = 1;
+ del_timer(&dev_priv->hangcheck_timer);
/* Cancel the retire work handler, wait for it to finish if running
*/
if (last_seqno == cur_seqno) {
if (stuck++ > 100) {
DRM_ERROR("hardware wedged\n");
- dev_priv->mm.wedged = 1;
+ atomic_set(&dev_priv->mm.wedged, 1);
DRM_WAKEUP(&dev_priv->irq_queue);
break;
}
i915_gem_retire_requests(dev);
spin_lock(&dev_priv->mm.active_list_lock);
- if (!dev_priv->mm.wedged) {
+ if (!atomic_read(&dev_priv->mm.wedged)) {
/* Active and flushing should now be empty as we've
* waited for a sequence higher than any pending execbuffer
*/
* the GPU domains and just stuff them onto inactive.
*/
while (!list_empty(&dev_priv->mm.active_list)) {
- struct drm_i915_gem_object *obj_priv;
+ struct drm_gem_object *obj;
+ uint32_t old_write_domain;
- obj_priv = list_first_entry(&dev_priv->mm.active_list,
- struct drm_i915_gem_object,
- list);
- obj_priv->obj->write_domain &= ~I915_GEM_GPU_DOMAINS;
- i915_gem_object_move_to_inactive(obj_priv->obj);
+ obj = list_first_entry(&dev_priv->mm.active_list,
+ struct drm_i915_gem_object,
+ list)->obj;
+ old_write_domain = obj->write_domain;
+ obj->write_domain &= ~I915_GEM_GPU_DOMAINS;
+ i915_gem_object_move_to_inactive(obj);
+
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
spin_unlock(&dev_priv->mm.active_list_lock);
while (!list_empty(&dev_priv->mm.flushing_list)) {
- struct drm_i915_gem_object *obj_priv;
+ struct drm_gem_object *obj;
+ uint32_t old_write_domain;
- obj_priv = list_first_entry(&dev_priv->mm.flushing_list,
- struct drm_i915_gem_object,
- list);
- obj_priv->obj->write_domain &= ~I915_GEM_GPU_DOMAINS;
- i915_gem_object_move_to_inactive(obj_priv->obj);
+ obj = list_first_entry(&dev_priv->mm.flushing_list,
+ struct drm_i915_gem_object,
+ list)->obj;
+ old_write_domain = obj->write_domain;
+ obj->write_domain &= ~I915_GEM_GPU_DOMAINS;
+ i915_gem_object_move_to_inactive(obj);
+
+ trace_i915_gem_object_change_domain(obj,
+ obj->read_domains,
+ old_write_domain);
}
/* Move all inactive buffers out of the GTT. */
- ret = i915_gem_evict_from_list(dev, &dev_priv->mm.inactive_list);
+ ret = i915_gem_evict_from_inactive_list(dev);
WARN_ON(!list_empty(&dev_priv->mm.inactive_list));
if (ret) {
mutex_unlock(&dev->struct_mutex);
if (drm_core_check_feature(dev, DRIVER_MODESET))
return 0;
- if (dev_priv->mm.wedged) {
+ if (atomic_read(&dev_priv->mm.wedged)) {
DRM_ERROR("Reenabling wedged hardware, good luck\n");
- dev_priv->mm.wedged = 0;
+ atomic_set(&dev_priv->mm.wedged, 0);
}
mutex_lock(&dev->struct_mutex);
i915_gem_retire_work_handler);
dev_priv->mm.next_gem_seqno = 1;
+ spin_lock(&shrink_list_lock);
+ list_add(&dev_priv->mm.shrink_list, &shrink_list);
+ spin_unlock(&shrink_list_lock);
+
/* Old X drivers will take 0-2 for front, back, depth buffers */
dev_priv->fence_reg_start = 3;
list_del_init(i915_file_priv->mm.request_list.next);
mutex_unlock(&dev->struct_mutex);
}
+
+static int
+i915_gem_shrink(int nr_to_scan, gfp_t gfp_mask)
+{
+ drm_i915_private_t *dev_priv, *next_dev;
+ struct drm_i915_gem_object *obj_priv, *next_obj;
+ int cnt = 0;
+ int would_deadlock = 1;
+
+ /* "fast-path" to count number of available objects */
+ if (nr_to_scan == 0) {
+ spin_lock(&shrink_list_lock);
+ list_for_each_entry(dev_priv, &shrink_list, mm.shrink_list) {
+ struct drm_device *dev = dev_priv->dev;
+
+ if (mutex_trylock(&dev->struct_mutex)) {
+ list_for_each_entry(obj_priv,
+ &dev_priv->mm.inactive_list,
+ list)
+ cnt++;
+ mutex_unlock(&dev->struct_mutex);
+ }
+ }
+ spin_unlock(&shrink_list_lock);
+
+ return (cnt / 100) * sysctl_vfs_cache_pressure;
+ }
+
+ spin_lock(&shrink_list_lock);
+
+ /* first scan for clean buffers */
+ list_for_each_entry_safe(dev_priv, next_dev,
+ &shrink_list, mm.shrink_list) {
+ struct drm_device *dev = dev_priv->dev;
+
+ if (! mutex_trylock(&dev->struct_mutex))
+ continue;
+
+ spin_unlock(&shrink_list_lock);
+
+ i915_gem_retire_requests(dev);
+
+ list_for_each_entry_safe(obj_priv, next_obj,
+ &dev_priv->mm.inactive_list,
+ list) {
+ if (i915_gem_object_is_purgeable(obj_priv)) {
+ i915_gem_object_unbind(obj_priv->obj);
+ if (--nr_to_scan <= 0)
+ break;
+ }
+ }
+
+ spin_lock(&shrink_list_lock);
+ mutex_unlock(&dev->struct_mutex);
+
+ would_deadlock = 0;
+
+ if (nr_to_scan <= 0)
+ break;
+ }
+
+ /* second pass, evict/count anything still on the inactive list */
+ list_for_each_entry_safe(dev_priv, next_dev,
+ &shrink_list, mm.shrink_list) {
+ struct drm_device *dev = dev_priv->dev;
+
+ if (! mutex_trylock(&dev->struct_mutex))
+ continue;
+
+ spin_unlock(&shrink_list_lock);
+
+ list_for_each_entry_safe(obj_priv, next_obj,
+ &dev_priv->mm.inactive_list,
+ list) {
+ if (nr_to_scan > 0) {
+ i915_gem_object_unbind(obj_priv->obj);
+ nr_to_scan--;
+ } else
+ cnt++;
+ }
+
+ spin_lock(&shrink_list_lock);
+ mutex_unlock(&dev->struct_mutex);
+
+ would_deadlock = 0;
+ }
+
+ spin_unlock(&shrink_list_lock);
+
+ if (would_deadlock)
+ return -1;
+ else if (cnt > 0)
+ return (cnt / 100) * sysctl_vfs_cache_pressure;
+ else
+ return 0;
+}
+
+static struct shrinker shrinker = {
+ .shrink = i915_gem_shrink,
+ .seeks = DEFAULT_SEEKS,
+};
+
+__init void
+i915_gem_shrinker_init(void)
+{
+ register_shrinker(&shrinker);
+}
+
+__exit void
+i915_gem_shrinker_exit(void)
+{
+ unregister_shrinker(&shrinker);
+}
#include "drm.h"
#include "i915_drm.h"
#include "i915_drv.h"
+#include "i915_trace.h"
#include "intel_drv.h"
#define MAX_NOPID ((u32)~0)
}
if (gt_iir & GT_USER_INTERRUPT) {
- dev_priv->mm.irq_gem_seqno = i915_get_gem_seqno(dev);
+ u32 seqno = i915_get_gem_seqno(dev);
+ dev_priv->mm.irq_gem_seqno = seqno;
+ trace_i915_gem_request_complete(dev, seqno);
DRM_WAKEUP(&dev_priv->irq_queue);
}
drm_i915_private_t *dev_priv = container_of(work, drm_i915_private_t,
error_work);
struct drm_device *dev = dev_priv->dev;
- char *event_string = "ERROR=1";
- char *envp[] = { event_string, NULL };
+ char *error_event[] = { "ERROR=1", NULL };
+ char *reset_event[] = { "RESET=1", NULL };
+ char *reset_done_event[] = { "ERROR=0", NULL };
DRM_DEBUG("generating error event\n");
-
- kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, envp);
+ kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, error_event);
+
+ if (atomic_read(&dev_priv->mm.wedged)) {
+ if (IS_I965G(dev)) {
+ DRM_DEBUG("resetting chip\n");
+ kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, reset_event);
+ if (!i965_reset(dev, GDRST_RENDER)) {
+ atomic_set(&dev_priv->mm.wedged, 0);
+ kobject_uevent_env(&dev->primary->kdev.kobj, KOBJ_CHANGE, reset_done_event);
+ }
+ } else {
+ printk("reboot required\n");
+ }
+ }
}
/**
* so userspace knows something bad happened (should trigger collection
* of a ring dump etc.).
*/
-static void i915_handle_error(struct drm_device *dev)
+static void i915_handle_error(struct drm_device *dev, bool wedged)
{
struct drm_i915_private *dev_priv = dev->dev_private;
u32 eir = I915_READ(EIR);
I915_WRITE(IIR, I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT);
}
+ if (wedged) {
+ atomic_set(&dev_priv->mm.wedged, 1);
+
+ /*
+ * Wakeup waiting processes so they don't hang
+ */
+ printk("i915: Waking up sleeping processes\n");
+ DRM_WAKEUP(&dev_priv->irq_queue);
+ }
+
queue_work(dev_priv->wq, &dev_priv->error_work);
}
pipeb_stats = I915_READ(PIPEBSTAT);
if (iir & I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT)
- i915_handle_error(dev);
+ i915_handle_error(dev, false);
/*
* Clear the PIPE(A|B)STAT regs before the IIR
}
if (iir & I915_USER_INTERRUPT) {
- dev_priv->mm.irq_gem_seqno = i915_get_gem_seqno(dev);
+ u32 seqno = i915_get_gem_seqno(dev);
+ dev_priv->mm.irq_gem_seqno = seqno;
+ trace_i915_gem_request_complete(dev, seqno);
DRM_WAKEUP(&dev_priv->irq_queue);
+ dev_priv->hangcheck_count = 0;
+ mod_timer(&dev_priv->hangcheck_timer, jiffies + DRM_I915_HANGCHECK_PERIOD);
}
if (pipea_stats & vblank_status) {
return -EINVAL;
}
+struct drm_i915_gem_request *i915_get_tail_request(struct drm_device *dev) {
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ return list_entry(dev_priv->mm.request_list.prev, struct drm_i915_gem_request, list);
+}
+
+/**
+ * This is called when the chip hasn't reported back with completed
+ * batchbuffers in a long time. The first time this is called we simply record
+ * ACTHD. If ACTHD hasn't changed by the time the hangcheck timer elapses
+ * again, we assume the chip is wedged and try to fix it.
+ */
+void i915_hangcheck_elapsed(unsigned long data)
+{
+ struct drm_device *dev = (struct drm_device *)data;
+ drm_i915_private_t *dev_priv = dev->dev_private;
+ uint32_t acthd;
+
+ if (!IS_I965G(dev))
+ acthd = I915_READ(ACTHD);
+ else
+ acthd = I915_READ(ACTHD_I965);
+
+ /* If all work is done then ACTHD clearly hasn't advanced. */
+ if (list_empty(&dev_priv->mm.request_list) ||
+ i915_seqno_passed(i915_get_gem_seqno(dev), i915_get_tail_request(dev)->seqno)) {
+ dev_priv->hangcheck_count = 0;
+ return;
+ }
+
+ if (dev_priv->last_acthd == acthd && dev_priv->hangcheck_count > 0) {
+ DRM_ERROR("Hangcheck timer elapsed... GPU hung\n");
+ i915_handle_error(dev, true);
+ return;
+ }
+
+ /* Reset timer case chip hangs without another request being added */
+ mod_timer(&dev_priv->hangcheck_timer, jiffies + DRM_I915_HANGCHECK_PERIOD);
+
+ if (acthd != dev_priv->last_acthd)
+ dev_priv->hangcheck_count = 0;
+ else
+ dev_priv->hangcheck_count++;
+
+ dev_priv->last_acthd = acthd;
+}
+
/* drm_dma.h hooks
*/
static void igdng_irq_preinstall(struct drm_device *dev)
struct drm_i915_private *dev_priv = dev->dev_private;
struct opregion_asle *asle = dev_priv->opregion.asle;
u32 blc_pwm_ctl, blc_pwm_ctl2;
+ u32 max_backlight, level, shift;
if (!(bclp & ASLE_BCLP_VALID))
return ASLE_BACKLIGHT_FAIL;
return ASLE_BACKLIGHT_FAIL;
blc_pwm_ctl = I915_READ(BLC_PWM_CTL);
- blc_pwm_ctl &= ~BACKLIGHT_DUTY_CYCLE_MASK;
blc_pwm_ctl2 = I915_READ(BLC_PWM_CTL2);
- if (blc_pwm_ctl2 & BLM_COMBINATION_MODE)
+ if (IS_I965G(dev) && (blc_pwm_ctl2 & BLM_COMBINATION_MODE))
pci_write_config_dword(dev->pdev, PCI_LBPC, bclp);
- else
- I915_WRITE(BLC_PWM_CTL, blc_pwm_ctl | ((bclp * 0x101)-1));
-
+ else {
+ if (IS_IGD(dev)) {
+ blc_pwm_ctl &= ~(BACKLIGHT_DUTY_CYCLE_MASK - 1);
+ max_backlight = (blc_pwm_ctl & BACKLIGHT_MODULATION_FREQ_MASK) >>
+ BACKLIGHT_MODULATION_FREQ_SHIFT;
+ shift = BACKLIGHT_DUTY_CYCLE_SHIFT + 1;
+ } else {
+ blc_pwm_ctl &= ~BACKLIGHT_DUTY_CYCLE_MASK;
+ max_backlight = ((blc_pwm_ctl & BACKLIGHT_MODULATION_FREQ_MASK) >>
+ BACKLIGHT_MODULATION_FREQ_SHIFT) * 2;
+ shift = BACKLIGHT_DUTY_CYCLE_SHIFT;
+ }
+ level = (bclp * max_backlight) / 255;
+ I915_WRITE(BLC_PWM_CTL, blc_pwm_ctl | (level << shift));
+ }
asle->cblv = (bclp*0x64)/0xff | ASLE_CBLV_VALID;
return 0;
#define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0)
#define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0)
#define LBB 0xf4
+#define GDRST 0xc0
+#define GDRST_FULL (0<<2)
+#define GDRST_RENDER (1<<2)
+#define GDRST_MEDIA (3<<2)
/* VGA stuff */
#define FBC_CTL_PLANEA (0<<0)
#define FBC_CTL_PLANEB (1<<0)
#define FBC_FENCE_OFF 0x0321b
+#define FBC_TAG 0x03300
#define FBC_LL_SIZE (1536)
+/* Framebuffer compression for GM45+ */
+#define DPFC_CB_BASE 0x3200
+#define DPFC_CONTROL 0x3208
+#define DPFC_CTL_EN (1<<31)
+#define DPFC_CTL_PLANEA (0<<30)
+#define DPFC_CTL_PLANEB (1<<30)
+#define DPFC_CTL_FENCE_EN (1<<29)
+#define DPFC_SR_EN (1<<10)
+#define DPFC_CTL_LIMIT_1X (0<<6)
+#define DPFC_CTL_LIMIT_2X (1<<6)
+#define DPFC_CTL_LIMIT_4X (2<<6)
+#define DPFC_RECOMP_CTL 0x320c
+#define DPFC_RECOMP_STALL_EN (1<<27)
+#define DPFC_RECOMP_STALL_WM_SHIFT (16)
+#define DPFC_RECOMP_STALL_WM_MASK (0x07ff0000)
+#define DPFC_RECOMP_TIMER_COUNT_SHIFT (0)
+#define DPFC_RECOMP_TIMER_COUNT_MASK (0x0000003f)
+#define DPFC_STATUS 0x3210
+#define DPFC_INVAL_SEG_SHIFT (16)
+#define DPFC_INVAL_SEG_MASK (0x07ff0000)
+#define DPFC_COMP_SEG_SHIFT (0)
+#define DPFC_COMP_SEG_MASK (0x000003ff)
+#define DPFC_STATUS2 0x3214
+#define DPFC_FENCE_YOFF 0x3218
+#define DPFC_CHICKEN 0x3224
+#define DPFC_HT_MODIFY (1<<31)
+
/*
* GPIO regs
*/
#define PF_ENABLE (1<<31)
#define PFA_WIN_SZ 0x68074
#define PFB_WIN_SZ 0x68874
+#define PFA_WIN_POS 0x68070
+#define PFB_WIN_POS 0x68870
/* legacy palette */
#define LGC_PALETTE_A 0x4a000
if (drm_core_check_feature(dev, DRIVER_MODESET))
return;
+
/* Pipe & plane A info */
dev_priv->savePIPEACONF = I915_READ(PIPEACONF);
dev_priv->savePIPEASRC = I915_READ(PIPEASRC);
dev_priv->savePIPEBSTAT = I915_READ(PIPEBSTAT);
return;
}
+
static void i915_restore_modeset_reg(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
return;
}
-int i915_save_state(struct drm_device *dev)
+
+void i915_save_display(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- int i;
-
- pci_read_config_byte(dev->pdev, LBB, &dev_priv->saveLBB);
-
- /* Render Standby */
- if (IS_I965G(dev) && IS_MOBILE(dev))
- dev_priv->saveRENDERSTANDBY = I915_READ(MCHBAR_RENDER_STANDBY);
-
- /* Hardware status page */
- dev_priv->saveHWS = I915_READ(HWS_PGA);
/* Display arbitration control */
dev_priv->saveDSPARB = I915_READ(DSPARB);
/* This is only meaningful in non-KMS mode */
/* Don't save them in KMS mode */
i915_save_modeset_reg(dev);
+
/* Cursor state */
dev_priv->saveCURACNTR = I915_READ(CURACNTR);
dev_priv->saveCURAPOS = I915_READ(CURAPOS);
dev_priv->saveFBC_CONTROL2 = I915_READ(FBC_CONTROL2);
dev_priv->saveFBC_CONTROL = I915_READ(FBC_CONTROL);
- /* Interrupt state */
- dev_priv->saveIIR = I915_READ(IIR);
- dev_priv->saveIER = I915_READ(IER);
- dev_priv->saveIMR = I915_READ(IMR);
-
/* VGA state */
dev_priv->saveVGA0 = I915_READ(VGA0);
dev_priv->saveVGA1 = I915_READ(VGA1);
dev_priv->saveVGA_PD = I915_READ(VGA_PD);
dev_priv->saveVGACNTRL = I915_READ(VGACNTRL);
- /* Clock gating state */
- dev_priv->saveD_STATE = I915_READ(D_STATE);
- dev_priv->saveDSPCLK_GATE_D = I915_READ(DSPCLK_GATE_D);
-
- /* Cache mode state */
- dev_priv->saveCACHE_MODE_0 = I915_READ(CACHE_MODE_0);
-
- /* Memory Arbitration state */
- dev_priv->saveMI_ARB_STATE = I915_READ(MI_ARB_STATE);
-
- /* Scratch space */
- for (i = 0; i < 16; i++) {
- dev_priv->saveSWF0[i] = I915_READ(SWF00 + (i << 2));
- dev_priv->saveSWF1[i] = I915_READ(SWF10 + (i << 2));
- }
- for (i = 0; i < 3; i++)
- dev_priv->saveSWF2[i] = I915_READ(SWF30 + (i << 2));
-
- /* Fences */
- if (IS_I965G(dev)) {
- for (i = 0; i < 16; i++)
- dev_priv->saveFENCE[i] = I915_READ64(FENCE_REG_965_0 + (i * 8));
- } else {
- for (i = 0; i < 8; i++)
- dev_priv->saveFENCE[i] = I915_READ(FENCE_REG_830_0 + (i * 4));
-
- if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
- for (i = 0; i < 8; i++)
- dev_priv->saveFENCE[i+8] = I915_READ(FENCE_REG_945_8 + (i * 4));
- }
i915_save_vga(dev);
-
- return 0;
}
-int i915_restore_state(struct drm_device *dev)
+void i915_restore_display(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- int i;
-
- pci_write_config_byte(dev->pdev, LBB, dev_priv->saveLBB);
-
- /* Render Standby */
- if (IS_I965G(dev) && IS_MOBILE(dev))
- I915_WRITE(MCHBAR_RENDER_STANDBY, dev_priv->saveRENDERSTANDBY);
-
- /* Hardware status page */
- I915_WRITE(HWS_PGA, dev_priv->saveHWS);
/* Display arbitration */
I915_WRITE(DSPARB, dev_priv->saveDSPARB);
- /* Fences */
- if (IS_I965G(dev)) {
- for (i = 0; i < 16; i++)
- I915_WRITE64(FENCE_REG_965_0 + (i * 8), dev_priv->saveFENCE[i]);
- } else {
- for (i = 0; i < 8; i++)
- I915_WRITE(FENCE_REG_830_0 + (i * 4), dev_priv->saveFENCE[i]);
- if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
- for (i = 0; i < 8; i++)
- I915_WRITE(FENCE_REG_945_8 + (i * 4), dev_priv->saveFENCE[i+8]);
- }
-
/* Display port ratios (must be done before clock is set) */
if (SUPPORTS_INTEGRATED_DP(dev)) {
I915_WRITE(PIPEA_GMCH_DATA_M, dev_priv->savePIPEA_GMCH_DATA_M);
I915_WRITE(PIPEA_DP_LINK_N, dev_priv->savePIPEA_DP_LINK_N);
I915_WRITE(PIPEB_DP_LINK_N, dev_priv->savePIPEB_DP_LINK_N);
}
+
/* This is only meaningful in non-KMS mode */
/* Don't restore them in KMS mode */
i915_restore_modeset_reg(dev);
+
/* Cursor state */
I915_WRITE(CURAPOS, dev_priv->saveCURAPOS);
I915_WRITE(CURACNTR, dev_priv->saveCURACNTR);
I915_WRITE(VGA_PD, dev_priv->saveVGA_PD);
DRM_UDELAY(150);
+ i915_restore_vga(dev);
+}
+
+int i915_save_state(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int i;
+
+ pci_read_config_byte(dev->pdev, LBB, &dev_priv->saveLBB);
+
+ /* Render Standby */
+ if (IS_I965G(dev) && IS_MOBILE(dev))
+ dev_priv->saveRENDERSTANDBY = I915_READ(MCHBAR_RENDER_STANDBY);
+
+ /* Hardware status page */
+ dev_priv->saveHWS = I915_READ(HWS_PGA);
+
+ i915_save_display(dev);
+
+ /* Interrupt state */
+ dev_priv->saveIER = I915_READ(IER);
+ dev_priv->saveIMR = I915_READ(IMR);
+
+ /* Clock gating state */
+ dev_priv->saveD_STATE = I915_READ(D_STATE);
+ dev_priv->saveDSPCLK_GATE_D = I915_READ(DSPCLK_GATE_D); /* Not sure about this */
+
+ /* Cache mode state */
+ dev_priv->saveCACHE_MODE_0 = I915_READ(CACHE_MODE_0);
+
+ /* Memory Arbitration state */
+ dev_priv->saveMI_ARB_STATE = I915_READ(MI_ARB_STATE);
+
+ /* Scratch space */
+ for (i = 0; i < 16; i++) {
+ dev_priv->saveSWF0[i] = I915_READ(SWF00 + (i << 2));
+ dev_priv->saveSWF1[i] = I915_READ(SWF10 + (i << 2));
+ }
+ for (i = 0; i < 3; i++)
+ dev_priv->saveSWF2[i] = I915_READ(SWF30 + (i << 2));
+
+ /* Fences */
+ if (IS_I965G(dev)) {
+ for (i = 0; i < 16; i++)
+ dev_priv->saveFENCE[i] = I915_READ64(FENCE_REG_965_0 + (i * 8));
+ } else {
+ for (i = 0; i < 8; i++)
+ dev_priv->saveFENCE[i] = I915_READ(FENCE_REG_830_0 + (i * 4));
+
+ if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
+ for (i = 0; i < 8; i++)
+ dev_priv->saveFENCE[i+8] = I915_READ(FENCE_REG_945_8 + (i * 4));
+ }
+
+ return 0;
+}
+
+int i915_restore_state(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ int i;
+
+ pci_write_config_byte(dev->pdev, LBB, dev_priv->saveLBB);
+
+ /* Render Standby */
+ if (IS_I965G(dev) && IS_MOBILE(dev))
+ I915_WRITE(MCHBAR_RENDER_STANDBY, dev_priv->saveRENDERSTANDBY);
+
+ /* Hardware status page */
+ I915_WRITE(HWS_PGA, dev_priv->saveHWS);
+
+ /* Fences */
+ if (IS_I965G(dev)) {
+ for (i = 0; i < 16; i++)
+ I915_WRITE64(FENCE_REG_965_0 + (i * 8), dev_priv->saveFENCE[i]);
+ } else {
+ for (i = 0; i < 8; i++)
+ I915_WRITE(FENCE_REG_830_0 + (i * 4), dev_priv->saveFENCE[i]);
+ if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
+ for (i = 0; i < 8; i++)
+ I915_WRITE(FENCE_REG_945_8 + (i * 4), dev_priv->saveFENCE[i+8]);
+ }
+
+ i915_restore_display(dev);
+
+ /* Interrupt state */
+ I915_WRITE (IER, dev_priv->saveIER);
+ I915_WRITE (IMR, dev_priv->saveIMR);
+
/* Clock gating state */
I915_WRITE (D_STATE, dev_priv->saveD_STATE);
I915_WRITE (DSPCLK_GATE_D, dev_priv->saveDSPCLK_GATE_D);
for (i = 0; i < 3; i++)
I915_WRITE(SWF30 + (i << 2), dev_priv->saveSWF2[i]);
- i915_restore_vga(dev);
-
return 0;
}
--- /dev/null
+#if !defined(_I915_TRACE_H_) || defined(TRACE_HEADER_MULTI_READ)
+#define _I915_TRACE_H_
+
+#include <linux/stringify.h>
+#include <linux/types.h>
+#include <linux/tracepoint.h>
+
+#include <drm/drmP.h>
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM i915
+#define TRACE_SYSTEM_STRING __stringify(TRACE_SYSTEM)
+#define TRACE_INCLUDE_FILE i915_trace
+
+/* object tracking */
+
+TRACE_EVENT(i915_gem_object_create,
+
+ TP_PROTO(struct drm_gem_object *obj),
+
+ TP_ARGS(obj),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ __field(u32, size)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ __entry->size = obj->size;
+ ),
+
+ TP_printk("obj=%p, size=%u", __entry->obj, __entry->size)
+);
+
+TRACE_EVENT(i915_gem_object_bind,
+
+ TP_PROTO(struct drm_gem_object *obj, u32 gtt_offset),
+
+ TP_ARGS(obj, gtt_offset),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ __field(u32, gtt_offset)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ __entry->gtt_offset = gtt_offset;
+ ),
+
+ TP_printk("obj=%p, gtt_offset=%08x",
+ __entry->obj, __entry->gtt_offset)
+);
+
+TRACE_EVENT(i915_gem_object_clflush,
+
+ TP_PROTO(struct drm_gem_object *obj),
+
+ TP_ARGS(obj),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ ),
+
+ TP_printk("obj=%p", __entry->obj)
+);
+
+TRACE_EVENT(i915_gem_object_change_domain,
+
+ TP_PROTO(struct drm_gem_object *obj, uint32_t old_read_domains, uint32_t old_write_domain),
+
+ TP_ARGS(obj, old_read_domains, old_write_domain),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ __field(u32, read_domains)
+ __field(u32, write_domain)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ __entry->read_domains = obj->read_domains | (old_read_domains << 16);
+ __entry->write_domain = obj->write_domain | (old_write_domain << 16);
+ ),
+
+ TP_printk("obj=%p, read=%04x, write=%04x",
+ __entry->obj,
+ __entry->read_domains, __entry->write_domain)
+);
+
+TRACE_EVENT(i915_gem_object_get_fence,
+
+ TP_PROTO(struct drm_gem_object *obj, int fence, int tiling_mode),
+
+ TP_ARGS(obj, fence, tiling_mode),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ __field(int, fence)
+ __field(int, tiling_mode)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ __entry->fence = fence;
+ __entry->tiling_mode = tiling_mode;
+ ),
+
+ TP_printk("obj=%p, fence=%d, tiling=%d",
+ __entry->obj, __entry->fence, __entry->tiling_mode)
+);
+
+TRACE_EVENT(i915_gem_object_unbind,
+
+ TP_PROTO(struct drm_gem_object *obj),
+
+ TP_ARGS(obj),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ ),
+
+ TP_printk("obj=%p", __entry->obj)
+);
+
+TRACE_EVENT(i915_gem_object_destroy,
+
+ TP_PROTO(struct drm_gem_object *obj),
+
+ TP_ARGS(obj),
+
+ TP_STRUCT__entry(
+ __field(struct drm_gem_object *, obj)
+ ),
+
+ TP_fast_assign(
+ __entry->obj = obj;
+ ),
+
+ TP_printk("obj=%p", __entry->obj)
+);
+
+/* batch tracing */
+
+TRACE_EVENT(i915_gem_request_submit,
+
+ TP_PROTO(struct drm_device *dev, u32 seqno),
+
+ TP_ARGS(dev, seqno),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ __field(u32, seqno)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->seqno = seqno;
+ ),
+
+ TP_printk("dev=%p, seqno=%u", __entry->dev, __entry->seqno)
+);
+
+TRACE_EVENT(i915_gem_request_flush,
+
+ TP_PROTO(struct drm_device *dev, u32 seqno,
+ u32 flush_domains, u32 invalidate_domains),
+
+ TP_ARGS(dev, seqno, flush_domains, invalidate_domains),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ __field(u32, seqno)
+ __field(u32, flush_domains)
+ __field(u32, invalidate_domains)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->seqno = seqno;
+ __entry->flush_domains = flush_domains;
+ __entry->invalidate_domains = invalidate_domains;
+ ),
+
+ TP_printk("dev=%p, seqno=%u, flush=%04x, invalidate=%04x",
+ __entry->dev, __entry->seqno,
+ __entry->flush_domains, __entry->invalidate_domains)
+);
+
+
+TRACE_EVENT(i915_gem_request_complete,
+
+ TP_PROTO(struct drm_device *dev, u32 seqno),
+
+ TP_ARGS(dev, seqno),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ __field(u32, seqno)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->seqno = seqno;
+ ),
+
+ TP_printk("dev=%p, seqno=%u", __entry->dev, __entry->seqno)
+);
+
+TRACE_EVENT(i915_gem_request_retire,
+
+ TP_PROTO(struct drm_device *dev, u32 seqno),
+
+ TP_ARGS(dev, seqno),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ __field(u32, seqno)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->seqno = seqno;
+ ),
+
+ TP_printk("dev=%p, seqno=%u", __entry->dev, __entry->seqno)
+);
+
+TRACE_EVENT(i915_gem_request_wait_begin,
+
+ TP_PROTO(struct drm_device *dev, u32 seqno),
+
+ TP_ARGS(dev, seqno),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ __field(u32, seqno)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->seqno = seqno;
+ ),
+
+ TP_printk("dev=%p, seqno=%u", __entry->dev, __entry->seqno)
+);
+
+TRACE_EVENT(i915_gem_request_wait_end,
+
+ TP_PROTO(struct drm_device *dev, u32 seqno),
+
+ TP_ARGS(dev, seqno),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ __field(u32, seqno)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->seqno = seqno;
+ ),
+
+ TP_printk("dev=%p, seqno=%u", __entry->dev, __entry->seqno)
+);
+
+TRACE_EVENT(i915_ring_wait_begin,
+
+ TP_PROTO(struct drm_device *dev),
+
+ TP_ARGS(dev),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ ),
+
+ TP_printk("dev=%p", __entry->dev)
+);
+
+TRACE_EVENT(i915_ring_wait_end,
+
+ TP_PROTO(struct drm_device *dev),
+
+ TP_ARGS(dev),
+
+ TP_STRUCT__entry(
+ __field(struct drm_device *, dev)
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ ),
+
+ TP_printk("dev=%p", __entry->dev)
+);
+
+#endif /* _I915_TRACE_H_ */
+
+/* This part must be outside protection */
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH ../../drivers/gpu/drm/i915
+#include <trace/define_trace.h>
--- /dev/null
+/*
+ * Copyright © 2009 Intel Corporation
+ *
+ * Authors:
+ * Chris Wilson <chris@chris-wilson.co.uk>
+ */
+
+#include "i915_drv.h"
+
+#define CREATE_TRACE_POINTS
+#include "i915_trace.h"
if (IS_I85X(dev_priv->dev))
dev_priv->lvds_ssc_freq =
general->ssc_freq ? 66 : 48;
+ else if (IS_IGDNG(dev_priv->dev))
+ dev_priv->lvds_ssc_freq =
+ general->ssc_freq ? 100 : 120;
else
dev_priv->lvds_ssc_freq =
general->ssc_freq ? 100 : 96;
{
struct drm_device *dev = connector->dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- u32 adpa, temp;
+ u32 adpa;
bool ret;
- temp = adpa = I915_READ(PCH_ADPA);
-
- adpa &= ~ADPA_DAC_ENABLE;
- I915_WRITE(PCH_ADPA, adpa);
+ adpa = I915_READ(PCH_ADPA);
adpa &= ~ADPA_CRT_HOTPLUG_MASK;
else
ret = false;
- /* restore origin register */
- I915_WRITE(PCH_ADPA, temp);
return ret;
}
* Eric Anholt <eric@anholt.net>
*/
+#include <linux/module.h>
+#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/kernel.h>
#include "drmP.h"
refclk, best_clock);
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
- if ((I915_READ(LVDS) & LVDS_CLKB_POWER_MASK) ==
+ if ((I915_READ(PCH_LVDS) & LVDS_CLKB_POWER_MASK) ==
LVDS_CLKB_POWER_UP)
clock.p2 = limit->p2.p2_fast;
else
mdelay(20);
}
+/* Parameters have changed, update FBC info */
+static void i8xx_enable_fbc(struct drm_crtc *crtc, unsigned long interval)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_framebuffer *fb = crtc->fb;
+ struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
+ struct drm_i915_gem_object *obj_priv = intel_fb->obj->driver_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int plane, i;
+ u32 fbc_ctl, fbc_ctl2;
+
+ dev_priv->cfb_pitch = dev_priv->cfb_size / FBC_LL_SIZE;
+
+ if (fb->pitch < dev_priv->cfb_pitch)
+ dev_priv->cfb_pitch = fb->pitch;
+
+ /* FBC_CTL wants 64B units */
+ dev_priv->cfb_pitch = (dev_priv->cfb_pitch / 64) - 1;
+ dev_priv->cfb_fence = obj_priv->fence_reg;
+ dev_priv->cfb_plane = intel_crtc->plane;
+ plane = dev_priv->cfb_plane == 0 ? FBC_CTL_PLANEA : FBC_CTL_PLANEB;
+
+ /* Clear old tags */
+ for (i = 0; i < (FBC_LL_SIZE / 32) + 1; i++)
+ I915_WRITE(FBC_TAG + (i * 4), 0);
+
+ /* Set it up... */
+ fbc_ctl2 = FBC_CTL_FENCE_DBL | FBC_CTL_IDLE_IMM | plane;
+ if (obj_priv->tiling_mode != I915_TILING_NONE)
+ fbc_ctl2 |= FBC_CTL_CPU_FENCE;
+ I915_WRITE(FBC_CONTROL2, fbc_ctl2);
+ I915_WRITE(FBC_FENCE_OFF, crtc->y);
+
+ /* enable it... */
+ fbc_ctl = FBC_CTL_EN | FBC_CTL_PERIODIC;
+ fbc_ctl |= (dev_priv->cfb_pitch & 0xff) << FBC_CTL_STRIDE_SHIFT;
+ fbc_ctl |= (interval & 0x2fff) << FBC_CTL_INTERVAL_SHIFT;
+ if (obj_priv->tiling_mode != I915_TILING_NONE)
+ fbc_ctl |= dev_priv->cfb_fence;
+ I915_WRITE(FBC_CONTROL, fbc_ctl);
+
+ DRM_DEBUG("enabled FBC, pitch %ld, yoff %d, plane %d, ",
+ dev_priv->cfb_pitch, crtc->y, dev_priv->cfb_plane);
+}
+
+void i8xx_disable_fbc(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ u32 fbc_ctl;
+
+ if (!I915_HAS_FBC(dev))
+ return;
+
+ /* Disable compression */
+ fbc_ctl = I915_READ(FBC_CONTROL);
+ fbc_ctl &= ~FBC_CTL_EN;
+ I915_WRITE(FBC_CONTROL, fbc_ctl);
+
+ /* Wait for compressing bit to clear */
+ while (I915_READ(FBC_STATUS) & FBC_STAT_COMPRESSING)
+ ; /* nothing */
+
+ intel_wait_for_vblank(dev);
+
+ DRM_DEBUG("disabled FBC\n");
+}
+
+static bool i8xx_fbc_enabled(struct drm_crtc *crtc)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+
+ return I915_READ(FBC_CONTROL) & FBC_CTL_EN;
+}
+
+static void g4x_enable_fbc(struct drm_crtc *crtc, unsigned long interval)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_framebuffer *fb = crtc->fb;
+ struct intel_framebuffer *intel_fb = to_intel_framebuffer(fb);
+ struct drm_i915_gem_object *obj_priv = intel_fb->obj->driver_private;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int plane = (intel_crtc->plane == 0 ? DPFC_CTL_PLANEA :
+ DPFC_CTL_PLANEB);
+ unsigned long stall_watermark = 200;
+ u32 dpfc_ctl;
+
+ dev_priv->cfb_pitch = (dev_priv->cfb_pitch / 64) - 1;
+ dev_priv->cfb_fence = obj_priv->fence_reg;
+ dev_priv->cfb_plane = intel_crtc->plane;
+
+ dpfc_ctl = plane | DPFC_SR_EN | DPFC_CTL_LIMIT_1X;
+ if (obj_priv->tiling_mode != I915_TILING_NONE) {
+ dpfc_ctl |= DPFC_CTL_FENCE_EN | dev_priv->cfb_fence;
+ I915_WRITE(DPFC_CHICKEN, DPFC_HT_MODIFY);
+ } else {
+ I915_WRITE(DPFC_CHICKEN, ~DPFC_HT_MODIFY);
+ }
+
+ I915_WRITE(DPFC_CONTROL, dpfc_ctl);
+ I915_WRITE(DPFC_RECOMP_CTL, DPFC_RECOMP_STALL_EN |
+ (stall_watermark << DPFC_RECOMP_STALL_WM_SHIFT) |
+ (interval << DPFC_RECOMP_TIMER_COUNT_SHIFT));
+ I915_WRITE(DPFC_FENCE_YOFF, crtc->y);
+
+ /* enable it... */
+ I915_WRITE(DPFC_CONTROL, I915_READ(DPFC_CONTROL) | DPFC_CTL_EN);
+
+ DRM_DEBUG("enabled fbc on plane %d\n", intel_crtc->plane);
+}
+
+void g4x_disable_fbc(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ u32 dpfc_ctl;
+
+ /* Disable compression */
+ dpfc_ctl = I915_READ(DPFC_CONTROL);
+ dpfc_ctl &= ~DPFC_CTL_EN;
+ I915_WRITE(DPFC_CONTROL, dpfc_ctl);
+ intel_wait_for_vblank(dev);
+
+ DRM_DEBUG("disabled FBC\n");
+}
+
+static bool g4x_fbc_enabled(struct drm_crtc *crtc)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+
+ return I915_READ(DPFC_CONTROL) & DPFC_CTL_EN;
+}
+
+/**
+ * intel_update_fbc - enable/disable FBC as needed
+ * @crtc: CRTC to point the compressor at
+ * @mode: mode in use
+ *
+ * Set up the framebuffer compression hardware at mode set time. We
+ * enable it if possible:
+ * - plane A only (on pre-965)
+ * - no pixel mulitply/line duplication
+ * - no alpha buffer discard
+ * - no dual wide
+ * - framebuffer <= 2048 in width, 1536 in height
+ *
+ * We can't assume that any compression will take place (worst case),
+ * so the compressed buffer has to be the same size as the uncompressed
+ * one. It also must reside (along with the line length buffer) in
+ * stolen memory.
+ *
+ * We need to enable/disable FBC on a global basis.
+ */
+static void intel_update_fbc(struct drm_crtc *crtc,
+ struct drm_display_mode *mode)
+{
+ struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ struct drm_framebuffer *fb = crtc->fb;
+ struct intel_framebuffer *intel_fb;
+ struct drm_i915_gem_object *obj_priv;
+ struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+ int plane = intel_crtc->plane;
+
+ if (!i915_powersave)
+ return;
+
+ if (!dev_priv->display.fbc_enabled ||
+ !dev_priv->display.enable_fbc ||
+ !dev_priv->display.disable_fbc)
+ return;
+
+ if (!crtc->fb)
+ return;
+
+ intel_fb = to_intel_framebuffer(fb);
+ obj_priv = intel_fb->obj->driver_private;
+
+ /*
+ * If FBC is already on, we just have to verify that we can
+ * keep it that way...
+ * Need to disable if:
+ * - changing FBC params (stride, fence, mode)
+ * - new fb is too large to fit in compressed buffer
+ * - going to an unsupported config (interlace, pixel multiply, etc.)
+ */
+ if (intel_fb->obj->size > dev_priv->cfb_size) {
+ DRM_DEBUG("framebuffer too large, disabling compression\n");
+ goto out_disable;
+ }
+ if ((mode->flags & DRM_MODE_FLAG_INTERLACE) ||
+ (mode->flags & DRM_MODE_FLAG_DBLSCAN)) {
+ DRM_DEBUG("mode incompatible with compression, disabling\n");
+ goto out_disable;
+ }
+ if ((mode->hdisplay > 2048) ||
+ (mode->vdisplay > 1536)) {
+ DRM_DEBUG("mode too large for compression, disabling\n");
+ goto out_disable;
+ }
+ if ((IS_I915GM(dev) || IS_I945GM(dev)) && plane != 0) {
+ DRM_DEBUG("plane not 0, disabling compression\n");
+ goto out_disable;
+ }
+ if (obj_priv->tiling_mode != I915_TILING_X) {
+ DRM_DEBUG("framebuffer not tiled, disabling compression\n");
+ goto out_disable;
+ }
+
+ if (dev_priv->display.fbc_enabled(crtc)) {
+ /* We can re-enable it in this case, but need to update pitch */
+ if (fb->pitch > dev_priv->cfb_pitch)
+ dev_priv->display.disable_fbc(dev);
+ if (obj_priv->fence_reg != dev_priv->cfb_fence)
+ dev_priv->display.disable_fbc(dev);
+ if (plane != dev_priv->cfb_plane)
+ dev_priv->display.disable_fbc(dev);
+ }
+
+ if (!dev_priv->display.fbc_enabled(crtc)) {
+ /* Now try to turn it back on if possible */
+ dev_priv->display.enable_fbc(crtc, 500);
+ }
+
+ return;
+
+out_disable:
+ DRM_DEBUG("unsupported config, disabling FBC\n");
+ /* Multiple disables should be harmless */
+ if (dev_priv->display.fbc_enabled(crtc))
+ dev_priv->display.disable_fbc(dev);
+}
+
static int
intel_pipe_set_base(struct drm_crtc *crtc, int x, int y,
struct drm_framebuffer *old_fb)
struct drm_i915_gem_object *obj_priv;
struct drm_gem_object *obj;
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
unsigned long Start, Offset;
- int dspbase = (pipe == 0 ? DSPAADDR : DSPBADDR);
- int dspsurf = (pipe == 0 ? DSPASURF : DSPBSURF);
- int dspstride = (pipe == 0) ? DSPASTRIDE : DSPBSTRIDE;
- int dsptileoff = (pipe == 0 ? DSPATILEOFF : DSPBTILEOFF);
- int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ int dspbase = (plane == 0 ? DSPAADDR : DSPBADDR);
+ int dspsurf = (plane == 0 ? DSPASURF : DSPBSURF);
+ int dspstride = (plane == 0) ? DSPASTRIDE : DSPBSTRIDE;
+ int dsptileoff = (plane == 0 ? DSPATILEOFF : DSPBTILEOFF);
+ int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
u32 dspcntr, alignment;
int ret;
return 0;
}
- switch (pipe) {
+ switch (plane) {
case 0:
case 1:
break;
default:
- DRM_ERROR("Can't update pipe %d in SAREA\n", pipe);
+ DRM_ERROR("Can't update plane %d in SAREA\n", plane);
return -EINVAL;
}
I915_READ(dspbase);
}
+ if ((IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
intel_wait_for_vblank(dev);
if (old_fb) {
int transconf_reg = (pipe == 0) ? TRANSACONF : TRANSBCONF;
int pf_ctl_reg = (pipe == 0) ? PFA_CTL_1 : PFB_CTL_1;
int pf_win_size = (pipe == 0) ? PFA_WIN_SZ : PFB_WIN_SZ;
+ int pf_win_pos = (pipe == 0) ? PFA_WIN_POS : PFB_WIN_POS;
int cpu_htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
int cpu_hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
int cpu_hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B;
}
}
+ /* Enable panel fitting for LVDS */
+ if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
+ temp = I915_READ(pf_ctl_reg);
+ I915_WRITE(pf_ctl_reg, temp | PF_ENABLE);
+
+ /* currently full aspect */
+ I915_WRITE(pf_win_pos, 0);
+
+ I915_WRITE(pf_win_size,
+ (dev_priv->panel_fixed_mode->hdisplay << 16) |
+ (dev_priv->panel_fixed_mode->vdisplay));
+ }
+
/* Enable CPU pipe */
temp = I915_READ(pipeconf_reg);
if ((temp & PIPEACONF_ENABLE) == 0) {
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
int dpll_reg = (pipe == 0) ? DPLL_A : DPLL_B;
- int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
- int dspbase_reg = (pipe == 0) ? DSPAADDR : DSPBADDR;
+ int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
+ int dspbase_reg = (plane == 0) ? DSPAADDR : DSPBADDR;
int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
u32 temp;
intel_crtc_load_lut(crtc);
+ if ((IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
/* Give the overlay scaler a chance to enable if it's on this pipe */
//intel_crtc_dpms_video(crtc, true); TODO
intel_update_watermarks(dev);
/* Give the overlay scaler a chance to disable if it's on this pipe */
//intel_crtc_dpms_video(crtc, FALSE); TODO
+ if (dev_priv->cfb_plane == plane &&
+ dev_priv->display.disable_fbc)
+ dev_priv->display.disable_fbc(dev);
+
/* Disable the VGA plane that we never use */
i915_disable_vga(dev);
static void intel_crtc_dpms(struct drm_crtc *crtc, int mode)
{
struct drm_device *dev = crtc->dev;
+ struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_i915_master_private *master_priv;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
bool enabled;
- if (IS_IGDNG(dev))
- igdng_crtc_dpms(crtc, mode);
- else
- i9xx_crtc_dpms(crtc, mode);
+ dev_priv->display.dpms(crtc, mode);
intel_crtc->dpms_mode = mode;
return true;
}
+static int i945_get_display_clock_speed(struct drm_device *dev)
+{
+ return 400000;
+}
-/** Returns the core display clock speed for i830 - i945 */
-static int intel_get_core_clock_speed(struct drm_device *dev)
+static int i915_get_display_clock_speed(struct drm_device *dev)
{
+ return 333000;
+}
- /* Core clock values taken from the published datasheets.
- * The 830 may go up to 166 Mhz, which we should check.
- */
- if (IS_I945G(dev))
- return 400000;
- else if (IS_I915G(dev))
- return 333000;
- else if (IS_I945GM(dev) || IS_845G(dev) || IS_IGDGM(dev))
- return 200000;
- else if (IS_I915GM(dev)) {
- u16 gcfgc = 0;
+static int i9xx_misc_get_display_clock_speed(struct drm_device *dev)
+{
+ return 200000;
+}
- pci_read_config_word(dev->pdev, GCFGC, &gcfgc);
+static int i915gm_get_display_clock_speed(struct drm_device *dev)
+{
+ u16 gcfgc = 0;
- if (gcfgc & GC_LOW_FREQUENCY_ENABLE)
- return 133000;
- else {
- switch (gcfgc & GC_DISPLAY_CLOCK_MASK) {
- case GC_DISPLAY_CLOCK_333_MHZ:
- return 333000;
- default:
- case GC_DISPLAY_CLOCK_190_200_MHZ:
- return 190000;
- }
- }
- } else if (IS_I865G(dev))
- return 266000;
- else if (IS_I855(dev)) {
- u16 hpllcc = 0;
- /* Assume that the hardware is in the high speed state. This
- * should be the default.
- */
- switch (hpllcc & GC_CLOCK_CONTROL_MASK) {
- case GC_CLOCK_133_200:
- case GC_CLOCK_100_200:
- return 200000;
- case GC_CLOCK_166_250:
- return 250000;
- case GC_CLOCK_100_133:
- return 133000;
+ pci_read_config_word(dev->pdev, GCFGC, &gcfgc);
+
+ if (gcfgc & GC_LOW_FREQUENCY_ENABLE)
+ return 133000;
+ else {
+ switch (gcfgc & GC_DISPLAY_CLOCK_MASK) {
+ case GC_DISPLAY_CLOCK_333_MHZ:
+ return 333000;
+ default:
+ case GC_DISPLAY_CLOCK_190_200_MHZ:
+ return 190000;
}
- } else /* 852, 830 */
+ }
+}
+
+static int i865_get_display_clock_speed(struct drm_device *dev)
+{
+ return 266000;
+}
+
+static int i855_get_display_clock_speed(struct drm_device *dev)
+{
+ u16 hpllcc = 0;
+ /* Assume that the hardware is in the high speed state. This
+ * should be the default.
+ */
+ switch (hpllcc & GC_CLOCK_CONTROL_MASK) {
+ case GC_CLOCK_133_200:
+ case GC_CLOCK_100_200:
+ return 200000;
+ case GC_CLOCK_166_250:
+ return 250000;
+ case GC_CLOCK_100_133:
return 133000;
+ }
+
+ /* Shouldn't happen */
+ return 0;
+}
- return 0; /* Silence gcc warning */
+static int i830_get_display_clock_speed(struct drm_device *dev)
+{
+ return 133000;
}
/**
{
long entries_required, wm_size;
- entries_required = (clock_in_khz * pixel_size * latency_ns) / 1000000;
+ /*
+ * Note: we need to make sure we don't overflow for various clock &
+ * latency values.
+ * clocks go from a few thousand to several hundred thousand.
+ * latency is usually a few thousand
+ */
+ entries_required = ((clock_in_khz / 1000) * pixel_size * latency_ns) /
+ 1000;
entries_required /= wm->cacheline_size;
DRM_DEBUG("FIFO entries required for mode: %d\n", entries_required);
for (i = 0; i < ARRAY_SIZE(cxsr_latency_table); i++) {
latency = &cxsr_latency_table[i];
if (is_desktop == latency->is_desktop &&
- fsb == latency->fsb_freq && mem == latency->mem_freq)
- break;
+ fsb == latency->fsb_freq && mem == latency->mem_freq)
+ return latency;
}
- if (i >= ARRAY_SIZE(cxsr_latency_table)) {
- DRM_DEBUG("Unknown FSB/MEM found, disable CxSR\n");
- return NULL;
- }
- return latency;
+
+ DRM_DEBUG("Unknown FSB/MEM found, disable CxSR\n");
+
+ return NULL;
}
static void igd_disable_cxsr(struct drm_device *dev)
*/
const static int latency_ns = 5000;
-static int intel_get_fifo_size(struct drm_device *dev, int plane)
+static int i9xx_get_fifo_size(struct drm_device *dev, int plane)
{
struct drm_i915_private *dev_priv = dev->dev_private;
uint32_t dsparb = I915_READ(DSPARB);
int size;
- if (IS_I9XX(dev)) {
- if (plane == 0)
- size = dsparb & 0x7f;
- else
- size = ((dsparb >> DSPARB_CSTART_SHIFT) & 0x7f) -
- (dsparb & 0x7f);
- } else if (IS_I85X(dev)) {
- if (plane == 0)
- size = dsparb & 0x1ff;
- else
- size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) -
- (dsparb & 0x1ff);
- size >>= 1; /* Convert to cachelines */
- } else if (IS_845G(dev)) {
+ if (plane == 0)
size = dsparb & 0x7f;
- size >>= 2; /* Convert to cachelines */
- } else {
- size = dsparb & 0x7f;
- size >>= 1; /* Convert to cachelines */
- }
+ else
+ size = ((dsparb >> DSPARB_CSTART_SHIFT) & 0x7f) -
+ (dsparb & 0x7f);
+
+ DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A",
+ size);
+
+ return size;
+}
+
+static int i85x_get_fifo_size(struct drm_device *dev, int plane)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ uint32_t dsparb = I915_READ(DSPARB);
+ int size;
+
+ if (plane == 0)
+ size = dsparb & 0x1ff;
+ else
+ size = ((dsparb >> DSPARB_BEND_SHIFT) & 0x1ff) -
+ (dsparb & 0x1ff);
+ size >>= 1; /* Convert to cachelines */
DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A",
size);
return size;
}
-static void g4x_update_wm(struct drm_device *dev)
+static int i845_get_fifo_size(struct drm_device *dev, int plane)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ uint32_t dsparb = I915_READ(DSPARB);
+ int size;
+
+ size = dsparb & 0x7f;
+ size >>= 2; /* Convert to cachelines */
+
+ DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A",
+ size);
+
+ return size;
+}
+
+static int i830_get_fifo_size(struct drm_device *dev, int plane)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+ uint32_t dsparb = I915_READ(DSPARB);
+ int size;
+
+ size = dsparb & 0x7f;
+ size >>= 1; /* Convert to cachelines */
+
+ DRM_DEBUG("FIFO size - (0x%08x) %s: %d\n", dsparb, plane ? "B" : "A",
+ size);
+
+ return size;
+}
+
+static void g4x_update_wm(struct drm_device *dev, int unused, int unused2,
+ int unused3, int unused4)
{
struct drm_i915_private *dev_priv = dev->dev_private;
u32 fw_blc_self = I915_READ(FW_BLC_SELF);
I915_WRITE(FW_BLC_SELF, fw_blc_self);
}
-static void i965_update_wm(struct drm_device *dev)
+static void i965_update_wm(struct drm_device *dev, int unused, int unused2,
+ int unused3, int unused4)
{
struct drm_i915_private *dev_priv = dev->dev_private;
cacheline_size = planea_params.cacheline_size;
/* Update per-plane FIFO sizes */
- planea_params.fifo_size = intel_get_fifo_size(dev, 0);
- planeb_params.fifo_size = intel_get_fifo_size(dev, 1);
+ planea_params.fifo_size = dev_priv->display.get_fifo_size(dev, 0);
+ planeb_params.fifo_size = dev_priv->display.get_fifo_size(dev, 1);
planea_wm = intel_calculate_wm(planea_clock, &planea_params,
pixel_size, latency_ns);
I915_WRITE(FW_BLC2, fwater_hi);
}
-static void i830_update_wm(struct drm_device *dev, int planea_clock,
- int pixel_size)
+static void i830_update_wm(struct drm_device *dev, int planea_clock, int unused,
+ int unused2, int pixel_size)
{
struct drm_i915_private *dev_priv = dev->dev_private;
uint32_t fwater_lo = I915_READ(FW_BLC) & ~0xfff;
int planea_wm;
- i830_wm_info.fifo_size = intel_get_fifo_size(dev, 0);
+ i830_wm_info.fifo_size = dev_priv->display.get_fifo_size(dev, 0);
planea_wm = intel_calculate_wm(planea_clock, &i830_wm_info,
pixel_size, latency_ns);
*/
static void intel_update_watermarks(struct drm_device *dev)
{
+ struct drm_i915_private *dev_priv = dev->dev_private;
struct drm_crtc *crtc;
struct intel_crtc *intel_crtc;
int sr_hdisplay = 0;
else if (IS_IGD(dev))
igd_disable_cxsr(dev);
- if (IS_G4X(dev))
- g4x_update_wm(dev);
- else if (IS_I965G(dev))
- i965_update_wm(dev);
- else if (IS_I9XX(dev) || IS_MOBILE(dev))
- i9xx_update_wm(dev, planea_clock, planeb_clock, sr_hdisplay,
- pixel_size);
- else
- i830_update_wm(dev, planea_clock, pixel_size);
+ dev_priv->display.update_wm(dev, planea_clock, planeb_clock,
+ sr_hdisplay, pixel_size);
}
static int intel_crtc_mode_set(struct drm_crtc *crtc,
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
int fp_reg = (pipe == 0) ? FPA0 : FPB0;
int dpll_reg = (pipe == 0) ? DPLL_A : DPLL_B;
int dpll_md_reg = (intel_crtc->pipe == 0) ? DPLL_A_MD : DPLL_B_MD;
- int dspcntr_reg = (pipe == 0) ? DSPACNTR : DSPBCNTR;
+ int dspcntr_reg = (plane == 0) ? DSPACNTR : DSPBCNTR;
int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
int htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
int hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
int vtot_reg = (pipe == 0) ? VTOTAL_A : VTOTAL_B;
int vblank_reg = (pipe == 0) ? VBLANK_A : VBLANK_B;
int vsync_reg = (pipe == 0) ? VSYNC_A : VSYNC_B;
- int dspsize_reg = (pipe == 0) ? DSPASIZE : DSPBSIZE;
- int dsppos_reg = (pipe == 0) ? DSPAPOS : DSPBPOS;
+ int dspsize_reg = (plane == 0) ? DSPASIZE : DSPBSIZE;
+ int dsppos_reg = (plane == 0) ? DSPAPOS : DSPBPOS;
int pipesrc_reg = (pipe == 0) ? PIPEASRC : PIPEBSRC;
int refclk, num_outputs = 0;
intel_clock_t clock, reduced_clock;
enable color space conversion */
if (!IS_IGDNG(dev)) {
if (pipe == 0)
- dspcntr |= DISPPLANE_SEL_PIPE_A;
+ dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
else
dspcntr |= DISPPLANE_SEL_PIPE_B;
}
* XXX: No double-wide on 915GM pipe B. Is that the only reason for the
* pipe == 0 check?
*/
- if (mode->clock > intel_get_core_clock_speed(dev) * 9 / 10)
+ if (mode->clock >
+ dev_priv->display.get_display_clock_speed(dev) * 9 / 10)
pipeconf |= PIPEACONF_DOUBLE_WIDE;
else
pipeconf &= ~PIPEACONF_DOUBLE_WIDE;
udelay(150);
if (IS_I965G(dev) && !IS_IGDNG(dev)) {
- sdvo_pixel_multiply = adjusted_mode->clock / mode->clock;
- I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) |
+ if (is_sdvo) {
+ sdvo_pixel_multiply = adjusted_mode->clock / mode->clock;
+ I915_WRITE(dpll_md_reg, (0 << DPLL_MD_UDI_DIVIDER_SHIFT) |
((sdvo_pixel_multiply - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT));
+ } else
+ I915_WRITE(dpll_md_reg, 0);
} else {
/* write it again -- the BIOS does, after all */
I915_WRITE(dpll_reg, dpll);
/* Flush the plane changes */
ret = intel_pipe_set_base(crtc, x, y, old_fb);
+ if ((IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
intel_update_watermarks(dev);
drm_vblank_post_modeset(dev, pipe);
struct drm_gem_object *bo;
struct drm_i915_gem_object *obj_priv;
int pipe = intel_crtc->pipe;
+ int plane = intel_crtc->plane;
uint32_t control = (pipe == 0) ? CURACNTR : CURBCNTR;
uint32_t base = (pipe == 0) ? CURABASE : CURBBASE;
uint32_t temp = I915_READ(control);
i915_gem_object_unpin(intel_crtc->cursor_bo);
drm_gem_object_unreference(intel_crtc->cursor_bo);
}
+
+ if ((IS_I965G(dev) || plane == 0))
+ intel_update_fbc(crtc, &crtc->mode);
+
mutex_unlock(&dev->struct_mutex);
intel_crtc->cursor_addr = addr;
intel_crtc->lut_b[i] = i;
}
+ /* Swap pipes & planes for FBC on pre-965 */
+ intel_crtc->pipe = pipe;
+ intel_crtc->plane = pipe;
+ if (IS_MOBILE(dev) && (IS_I9XX(dev) && !IS_I965G(dev))) {
+ DRM_DEBUG("swapping pipes & planes for FBC\n");
+ intel_crtc->plane = ((pipe == 0) ? 1 : 0);
+ }
+
intel_crtc->cursor_addr = 0;
intel_crtc->dpms_mode = DRM_MODE_DPMS_OFF;
drm_crtc_helper_add(&intel_crtc->base, &intel_helper_funcs);
}
}
+/* Set up chip specific display functions */
+static void intel_init_display(struct drm_device *dev)
+{
+ struct drm_i915_private *dev_priv = dev->dev_private;
+
+ /* We always want a DPMS function */
+ if (IS_IGDNG(dev))
+ dev_priv->display.dpms = igdng_crtc_dpms;
+ else
+ dev_priv->display.dpms = i9xx_crtc_dpms;
+
+ /* Only mobile has FBC, leave pointers NULL for other chips */
+ if (IS_MOBILE(dev)) {
+ if (IS_GM45(dev)) {
+ dev_priv->display.fbc_enabled = g4x_fbc_enabled;
+ dev_priv->display.enable_fbc = g4x_enable_fbc;
+ dev_priv->display.disable_fbc = g4x_disable_fbc;
+ } else if (IS_I965GM(dev) || IS_I945GM(dev) || IS_I915GM(dev)) {
+ dev_priv->display.fbc_enabled = i8xx_fbc_enabled;
+ dev_priv->display.enable_fbc = i8xx_enable_fbc;
+ dev_priv->display.disable_fbc = i8xx_disable_fbc;
+ }
+ /* 855GM needs testing */
+ }
+
+ /* Returns the core display clock speed */
+ if (IS_I945G(dev))
+ dev_priv->display.get_display_clock_speed =
+ i945_get_display_clock_speed;
+ else if (IS_I915G(dev))
+ dev_priv->display.get_display_clock_speed =
+ i915_get_display_clock_speed;
+ else if (IS_I945GM(dev) || IS_845G(dev) || IS_IGDGM(dev))
+ dev_priv->display.get_display_clock_speed =
+ i9xx_misc_get_display_clock_speed;
+ else if (IS_I915GM(dev))
+ dev_priv->display.get_display_clock_speed =
+ i915gm_get_display_clock_speed;
+ else if (IS_I865G(dev))
+ dev_priv->display.get_display_clock_speed =
+ i865_get_display_clock_speed;
+ else if (IS_I855(dev))
+ dev_priv->display.get_display_clock_speed =
+ i855_get_display_clock_speed;
+ else /* 852, 830 */
+ dev_priv->display.get_display_clock_speed =
+ i830_get_display_clock_speed;
+
+ /* For FIFO watermark updates */
+ if (IS_G4X(dev))
+ dev_priv->display.update_wm = g4x_update_wm;
+ else if (IS_I965G(dev))
+ dev_priv->display.update_wm = i965_update_wm;
+ else if (IS_I9XX(dev) || IS_MOBILE(dev)) {
+ dev_priv->display.update_wm = i9xx_update_wm;
+ dev_priv->display.get_fifo_size = i9xx_get_fifo_size;
+ } else {
+ if (IS_I85X(dev))
+ dev_priv->display.get_fifo_size = i85x_get_fifo_size;
+ else if (IS_845G(dev))
+ dev_priv->display.get_fifo_size = i845_get_fifo_size;
+ else
+ dev_priv->display.get_fifo_size = i830_get_fifo_size;
+ dev_priv->display.update_wm = i830_update_wm;
+ }
+}
+
void intel_modeset_init(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
dev->mode_config.funcs = (void *)&intel_mode_funcs;
+ intel_init_display(dev);
+
if (IS_I965G(dev)) {
dev->mode_config.max_width = 8192;
dev->mode_config.max_height = 8192;
mutex_unlock(&dev->struct_mutex);
+ if (dev_priv->display.disable_fbc)
+ dev_priv->display.disable_fbc(dev);
+
drm_mode_config_cleanup(dev);
}
#include <linux/i2c.h>
#include <linux/i2c-id.h>
#include <linux/i2c-algo-bit.h>
+#include "i915_drv.h"
#include "drm_crtc.h"
#include "drm_crtc_helper.h"
struct intel_crtc {
struct drm_crtc base;
- int pipe;
- int plane;
+ enum pipe pipe;
+ enum plane plane;
struct drm_gem_object *cursor_bo;
uint32_t cursor_addr;
u8 lut_r[256], lut_g[256], lut_b[256];
static int intelfb_create(struct drm_device *dev, uint32_t fb_width,
uint32_t fb_height, uint32_t surface_width,
uint32_t surface_height,
+ uint32_t surface_depth, uint32_t surface_bpp,
struct drm_framebuffer **fb_p)
{
struct fb_info *info;
mode_cmd.width = surface_width;
mode_cmd.height = surface_height;
- mode_cmd.bpp = 32;
+ mode_cmd.bpp = surface_bpp;
mode_cmd.pitch = ALIGN(mode_cmd.width * ((mode_cmd.bpp + 1) / 8), 64);
- mode_cmd.depth = 24;
+ mode_cmd.depth = surface_depth;
size = mode_cmd.pitch * mode_cmd.height;
size = ALIGN(size, PAGE_SIZE);
* Jesse Barnes <jesse.barnes@intel.com>
*/
+#include <acpi/button.h>
#include <linux/dmi.h>
#include <linux/i2c.h>
#include "drmP.h"
goto out;
}
+ /* full screen scale for now */
+ if (IS_IGDNG(dev))
+ goto out;
+
/* 965+ wants fuzzy fitting */
if (IS_I965G(dev))
pfit_control |= (intel_crtc->pipe << PFIT_PIPE_SHIFT) |
* to register description and PRM.
* Change the value here to see the borders for debugging
*/
- I915_WRITE(BCLRPAT_A, 0);
- I915_WRITE(BCLRPAT_B, 0);
+ if (!IS_IGDNG(dev)) {
+ I915_WRITE(BCLRPAT_A, 0);
+ I915_WRITE(BCLRPAT_B, 0);
+ }
switch (lvds_priv->fitting_mode) {
case DRM_MODE_SCALE_CENTER:
* settings.
*/
- /* No panel fitting yet, fixme */
if (IS_IGDNG(dev))
return;
I915_WRITE(PFIT_CONTROL, lvds_priv->pfit_control);
}
+/* Some lid devices report incorrect lid status, assume they're connected */
+static const struct dmi_system_id bad_lid_status[] = {
+ {
+ .ident = "Aspire One",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Aspire one"),
+ },
+ },
+ { }
+};
+
/**
* Detect the LVDS connection.
*
- * This always returns CONNECTOR_STATUS_CONNECTED. This connector should only have
- * been set up if the LVDS was actually connected anyway.
+ * Since LVDS doesn't have hotlug, we use the lid as a proxy. Open means
+ * connected and closed means disconnected. We also send hotplug events as
+ * needed, using lid status notification from the input layer.
*/
static enum drm_connector_status intel_lvds_detect(struct drm_connector *connector)
{
- return connector_status_connected;
+ enum drm_connector_status status = connector_status_connected;
+
+ if (!acpi_lid_open() && !dmi_check_system(bad_lid_status))
+ status = connector_status_disconnected;
+
+ return status;
}
/**
return 0;
}
+static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
+ void *unused)
+{
+ struct drm_i915_private *dev_priv =
+ container_of(nb, struct drm_i915_private, lid_notifier);
+ struct drm_device *dev = dev_priv->dev;
+
+ if (acpi_lid_open() && !dev_priv->suspended) {
+ mutex_lock(&dev->mode_config.mutex);
+ drm_helper_resume_force_mode(dev);
+ mutex_unlock(&dev->mode_config.mutex);
+ }
+
+ drm_sysfs_hotplug_event(dev_priv->dev);
+
+ return NOTIFY_OK;
+}
+
/**
* intel_lvds_destroy - unregister and free LVDS structures
* @connector: connector to free
*/
static void intel_lvds_destroy(struct drm_connector *connector)
{
+ struct drm_device *dev = connector->dev;
struct intel_output *intel_output = to_intel_output(connector);
+ struct drm_i915_private *dev_priv = dev->dev_private;
if (intel_output->ddc_bus)
intel_i2c_destroy(intel_output->ddc_bus);
+ if (dev_priv->lid_notifier.notifier_call)
+ acpi_lid_notifier_unregister(&dev_priv->lid_notifier);
drm_sysfs_connector_remove(connector);
drm_connector_cleanup(connector);
kfree(connector);
pwm |= PWM_PCH_ENABLE;
I915_WRITE(BLC_PWM_PCH_CTL1, pwm);
}
+ dev_priv->lid_notifier.notifier_call = intel_lid_notify;
+ if (acpi_lid_notifier_register(&dev_priv->lid_notifier)) {
+ DRM_DEBUG("lid notifier registration failed\n");
+ dev_priv->lid_notifier.notifier_call = NULL;
+ }
drm_sysfs_connector_add(connector);
return;
struct intel_sdvo_dtd save_input_dtd_1, save_input_dtd_2;
struct intel_sdvo_dtd save_output_dtd[16];
u32 save_SDVOX;
+ /* add the property for the SDVO-TV */
+ struct drm_property *left_property;
+ struct drm_property *right_property;
+ struct drm_property *top_property;
+ struct drm_property *bottom_property;
+ struct drm_property *hpos_property;
+ struct drm_property *vpos_property;
+
+ /* add the property for the SDVO-TV/LVDS */
+ struct drm_property *brightness_property;
+ struct drm_property *contrast_property;
+ struct drm_property *saturation_property;
+ struct drm_property *hue_property;
+
+ /* Add variable to record current setting for the above property */
+ u32 left_margin, right_margin, top_margin, bottom_margin;
+ /* this is to get the range of margin.*/
+ u32 max_hscan, max_vscan;
+ u32 max_hpos, cur_hpos;
+ u32 max_vpos, cur_vpos;
+ u32 cur_brightness, max_brightness;
+ u32 cur_contrast, max_contrast;
+ u32 cur_saturation, max_saturation;
+ u32 cur_hue, max_hue;
};
static bool
SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SDTV_RESOLUTION_SUPPORT),
SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SCALED_HDTV_RESOLUTION_SUPPORT),
SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SUPPORTED_ENHANCEMENTS),
+ /* Add the op code for SDVO enhancements */
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_POSITION_H),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_POSITION_H),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_POSITION_H),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_POSITION_V),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_POSITION_V),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_POSITION_V),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_SATURATION),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SATURATION),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_SATURATION),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_HUE),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_HUE),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_HUE),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_CONTRAST),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_CONTRAST),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_CONTRAST),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_BRIGHTNESS),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_BRIGHTNESS),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_BRIGHTNESS),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_OVERSCAN_H),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_OVERSCAN_H),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_OVERSCAN_H),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_MAX_OVERSCAN_V),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_OVERSCAN_V),
+ SDVO_CMD_NAME_ENTRY(SDVO_CMD_SET_OVERSCAN_V),
/* HDMI op code */
SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_SUPP_ENCODE),
SDVO_CMD_NAME_ENTRY(SDVO_CMD_GET_ENCODE),
status = intel_sdvo_read_response(output, NULL, 0);
if (status != SDVO_CMD_STATUS_SUCCESS)
- DRM_DEBUG("%s: Failed to set TV format\n",
+ DRM_DEBUG_KMS("%s: Failed to set TV format\n",
SDVO_NAME(sdvo_priv));
}
return 1;
}
+static
+void intel_sdvo_destroy_enhance_property(struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+ struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
+ struct drm_device *dev = connector->dev;
+
+ if (sdvo_priv->is_tv) {
+ if (sdvo_priv->left_property)
+ drm_property_destroy(dev, sdvo_priv->left_property);
+ if (sdvo_priv->right_property)
+ drm_property_destroy(dev, sdvo_priv->right_property);
+ if (sdvo_priv->top_property)
+ drm_property_destroy(dev, sdvo_priv->top_property);
+ if (sdvo_priv->bottom_property)
+ drm_property_destroy(dev, sdvo_priv->bottom_property);
+ if (sdvo_priv->hpos_property)
+ drm_property_destroy(dev, sdvo_priv->hpos_property);
+ if (sdvo_priv->vpos_property)
+ drm_property_destroy(dev, sdvo_priv->vpos_property);
+ }
+ if (sdvo_priv->is_tv) {
+ if (sdvo_priv->saturation_property)
+ drm_property_destroy(dev,
+ sdvo_priv->saturation_property);
+ if (sdvo_priv->contrast_property)
+ drm_property_destroy(dev,
+ sdvo_priv->contrast_property);
+ if (sdvo_priv->hue_property)
+ drm_property_destroy(dev, sdvo_priv->hue_property);
+ }
+ if (sdvo_priv->is_tv || sdvo_priv->is_lvds) {
+ if (sdvo_priv->brightness_property)
+ drm_property_destroy(dev,
+ sdvo_priv->brightness_property);
+ }
+ return;
+}
+
static void intel_sdvo_destroy(struct drm_connector *connector)
{
struct intel_output *intel_output = to_intel_output(connector);
drm_property_destroy(connector->dev,
sdvo_priv->tv_format_property);
+ if (sdvo_priv->is_tv || sdvo_priv->is_lvds)
+ intel_sdvo_destroy_enhance_property(connector);
+
drm_sysfs_connector_remove(connector);
drm_connector_cleanup(connector);
struct drm_crtc *crtc = encoder->crtc;
int ret = 0;
bool changed = false;
+ uint8_t cmd, status;
+ uint16_t temp_value;
ret = drm_connector_property_set_value(connector, property, val);
if (ret < 0)
sdvo_priv->tv_format_name = sdvo_priv->tv_format_supported[val];
changed = true;
- } else {
- ret = -EINVAL;
- goto out;
}
+ if (sdvo_priv->is_tv || sdvo_priv->is_lvds) {
+ cmd = 0;
+ temp_value = val;
+ if (sdvo_priv->left_property == property) {
+ drm_connector_property_set_value(connector,
+ sdvo_priv->right_property, val);
+ if (sdvo_priv->left_margin == temp_value)
+ goto out;
+
+ sdvo_priv->left_margin = temp_value;
+ sdvo_priv->right_margin = temp_value;
+ temp_value = sdvo_priv->max_hscan -
+ sdvo_priv->left_margin;
+ cmd = SDVO_CMD_SET_OVERSCAN_H;
+ } else if (sdvo_priv->right_property == property) {
+ drm_connector_property_set_value(connector,
+ sdvo_priv->left_property, val);
+ if (sdvo_priv->right_margin == temp_value)
+ goto out;
+
+ sdvo_priv->left_margin = temp_value;
+ sdvo_priv->right_margin = temp_value;
+ temp_value = sdvo_priv->max_hscan -
+ sdvo_priv->left_margin;
+ cmd = SDVO_CMD_SET_OVERSCAN_H;
+ } else if (sdvo_priv->top_property == property) {
+ drm_connector_property_set_value(connector,
+ sdvo_priv->bottom_property, val);
+ if (sdvo_priv->top_margin == temp_value)
+ goto out;
+
+ sdvo_priv->top_margin = temp_value;
+ sdvo_priv->bottom_margin = temp_value;
+ temp_value = sdvo_priv->max_vscan -
+ sdvo_priv->top_margin;
+ cmd = SDVO_CMD_SET_OVERSCAN_V;
+ } else if (sdvo_priv->bottom_property == property) {
+ drm_connector_property_set_value(connector,
+ sdvo_priv->top_property, val);
+ if (sdvo_priv->bottom_margin == temp_value)
+ goto out;
+ sdvo_priv->top_margin = temp_value;
+ sdvo_priv->bottom_margin = temp_value;
+ temp_value = sdvo_priv->max_vscan -
+ sdvo_priv->top_margin;
+ cmd = SDVO_CMD_SET_OVERSCAN_V;
+ } else if (sdvo_priv->hpos_property == property) {
+ if (sdvo_priv->cur_hpos == temp_value)
+ goto out;
+
+ cmd = SDVO_CMD_SET_POSITION_H;
+ sdvo_priv->cur_hpos = temp_value;
+ } else if (sdvo_priv->vpos_property == property) {
+ if (sdvo_priv->cur_vpos == temp_value)
+ goto out;
+
+ cmd = SDVO_CMD_SET_POSITION_V;
+ sdvo_priv->cur_vpos = temp_value;
+ } else if (sdvo_priv->saturation_property == property) {
+ if (sdvo_priv->cur_saturation == temp_value)
+ goto out;
+
+ cmd = SDVO_CMD_SET_SATURATION;
+ sdvo_priv->cur_saturation = temp_value;
+ } else if (sdvo_priv->contrast_property == property) {
+ if (sdvo_priv->cur_contrast == temp_value)
+ goto out;
+
+ cmd = SDVO_CMD_SET_CONTRAST;
+ sdvo_priv->cur_contrast = temp_value;
+ } else if (sdvo_priv->hue_property == property) {
+ if (sdvo_priv->cur_hue == temp_value)
+ goto out;
+
+ cmd = SDVO_CMD_SET_HUE;
+ sdvo_priv->cur_hue = temp_value;
+ } else if (sdvo_priv->brightness_property == property) {
+ if (sdvo_priv->cur_brightness == temp_value)
+ goto out;
+
+ cmd = SDVO_CMD_SET_BRIGHTNESS;
+ sdvo_priv->cur_brightness = temp_value;
+ }
+ if (cmd) {
+ intel_sdvo_write_cmd(intel_output, cmd, &temp_value, 2);
+ status = intel_sdvo_read_response(intel_output,
+ NULL, 0);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO command \n");
+ return -EINVAL;
+ }
+ changed = true;
+ }
+ }
if (changed && crtc)
drm_crtc_helper_set_mode(crtc, &crtc->mode, crtc->x,
crtc->y, crtc->fb);
sdvo_priv->controlled_output = SDVO_OUTPUT_RGB1;
encoder->encoder_type = DRM_MODE_ENCODER_DAC;
connector->connector_type = DRM_MODE_CONNECTOR_VGA;
+ intel_output->clone_mask = (1 << INTEL_SDVO_NON_TV_CLONE_BIT) |
+ (1 << INTEL_ANALOG_CLONE_BIT);
} else if (flags & SDVO_OUTPUT_LVDS0) {
sdvo_priv->controlled_output = SDVO_OUTPUT_LVDS0;
}
+static void intel_sdvo_create_enhance_property(struct drm_connector *connector)
+{
+ struct intel_output *intel_output = to_intel_output(connector);
+ struct intel_sdvo_priv *sdvo_priv = intel_output->dev_priv;
+ struct intel_sdvo_enhancements_reply sdvo_data;
+ struct drm_device *dev = connector->dev;
+ uint8_t status;
+ uint16_t response, data_value[2];
+
+ intel_sdvo_write_cmd(intel_output, SDVO_CMD_GET_SUPPORTED_ENHANCEMENTS,
+ NULL, 0);
+ status = intel_sdvo_read_response(intel_output, &sdvo_data,
+ sizeof(sdvo_data));
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS(" incorrect response is returned\n");
+ return;
+ }
+ response = *((uint16_t *)&sdvo_data);
+ if (!response) {
+ DRM_DEBUG_KMS("No enhancement is supported\n");
+ return;
+ }
+ if (sdvo_priv->is_tv) {
+ /* when horizontal overscan is supported, Add the left/right
+ * property
+ */
+ if (sdvo_data.overscan_h) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_OVERSCAN_H, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO max "
+ "h_overscan\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_OVERSCAN_H, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO h_overscan\n");
+ return;
+ }
+ sdvo_priv->max_hscan = data_value[0];
+ sdvo_priv->left_margin = data_value[0] - response;
+ sdvo_priv->right_margin = sdvo_priv->left_margin;
+ sdvo_priv->left_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "left_margin", 2);
+ sdvo_priv->left_property->values[0] = 0;
+ sdvo_priv->left_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->left_property,
+ sdvo_priv->left_margin);
+ sdvo_priv->right_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "right_margin", 2);
+ sdvo_priv->right_property->values[0] = 0;
+ sdvo_priv->right_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->right_property,
+ sdvo_priv->right_margin);
+ DRM_DEBUG_KMS("h_overscan: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ if (sdvo_data.overscan_v) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_OVERSCAN_V, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO max "
+ "v_overscan\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_OVERSCAN_V, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO v_overscan\n");
+ return;
+ }
+ sdvo_priv->max_vscan = data_value[0];
+ sdvo_priv->top_margin = data_value[0] - response;
+ sdvo_priv->bottom_margin = sdvo_priv->top_margin;
+ sdvo_priv->top_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "top_margin", 2);
+ sdvo_priv->top_property->values[0] = 0;
+ sdvo_priv->top_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->top_property,
+ sdvo_priv->top_margin);
+ sdvo_priv->bottom_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "bottom_margin", 2);
+ sdvo_priv->bottom_property->values[0] = 0;
+ sdvo_priv->bottom_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->bottom_property,
+ sdvo_priv->bottom_margin);
+ DRM_DEBUG_KMS("v_overscan: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ if (sdvo_data.position_h) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_POSITION_H, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO Max h_pos\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_POSITION_H, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO get h_postion\n");
+ return;
+ }
+ sdvo_priv->max_hpos = data_value[0];
+ sdvo_priv->cur_hpos = response;
+ sdvo_priv->hpos_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "hpos", 2);
+ sdvo_priv->hpos_property->values[0] = 0;
+ sdvo_priv->hpos_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->hpos_property,
+ sdvo_priv->cur_hpos);
+ DRM_DEBUG_KMS("h_position: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ if (sdvo_data.position_v) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_POSITION_V, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO Max v_pos\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_POSITION_V, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO get v_postion\n");
+ return;
+ }
+ sdvo_priv->max_vpos = data_value[0];
+ sdvo_priv->cur_vpos = response;
+ sdvo_priv->vpos_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "vpos", 2);
+ sdvo_priv->vpos_property->values[0] = 0;
+ sdvo_priv->vpos_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->vpos_property,
+ sdvo_priv->cur_vpos);
+ DRM_DEBUG_KMS("v_position: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ }
+ if (sdvo_priv->is_tv) {
+ if (sdvo_data.saturation) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_SATURATION, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO Max sat\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_SATURATION, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO get sat\n");
+ return;
+ }
+ sdvo_priv->max_saturation = data_value[0];
+ sdvo_priv->cur_saturation = response;
+ sdvo_priv->saturation_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "saturation", 2);
+ sdvo_priv->saturation_property->values[0] = 0;
+ sdvo_priv->saturation_property->values[1] =
+ data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->saturation_property,
+ sdvo_priv->cur_saturation);
+ DRM_DEBUG_KMS("saturation: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ if (sdvo_data.contrast) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_CONTRAST, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO Max contrast\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_CONTRAST, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO get contrast\n");
+ return;
+ }
+ sdvo_priv->max_contrast = data_value[0];
+ sdvo_priv->cur_contrast = response;
+ sdvo_priv->contrast_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "contrast", 2);
+ sdvo_priv->contrast_property->values[0] = 0;
+ sdvo_priv->contrast_property->values[1] = data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->contrast_property,
+ sdvo_priv->cur_contrast);
+ DRM_DEBUG_KMS("contrast: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ if (sdvo_data.hue) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_HUE, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO Max hue\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_HUE, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO get hue\n");
+ return;
+ }
+ sdvo_priv->max_hue = data_value[0];
+ sdvo_priv->cur_hue = response;
+ sdvo_priv->hue_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "hue", 2);
+ sdvo_priv->hue_property->values[0] = 0;
+ sdvo_priv->hue_property->values[1] =
+ data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->hue_property,
+ sdvo_priv->cur_hue);
+ DRM_DEBUG_KMS("hue: max %d, default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ }
+ if (sdvo_priv->is_tv || sdvo_priv->is_lvds) {
+ if (sdvo_data.brightness) {
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_MAX_BRIGHTNESS, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &data_value, 4);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO Max bright\n");
+ return;
+ }
+ intel_sdvo_write_cmd(intel_output,
+ SDVO_CMD_GET_BRIGHTNESS, NULL, 0);
+ status = intel_sdvo_read_response(intel_output,
+ &response, 2);
+ if (status != SDVO_CMD_STATUS_SUCCESS) {
+ DRM_DEBUG_KMS("Incorrect SDVO get brigh\n");
+ return;
+ }
+ sdvo_priv->max_brightness = data_value[0];
+ sdvo_priv->cur_brightness = response;
+ sdvo_priv->brightness_property =
+ drm_property_create(dev, DRM_MODE_PROP_RANGE,
+ "brightness", 2);
+ sdvo_priv->brightness_property->values[0] = 0;
+ sdvo_priv->brightness_property->values[1] =
+ data_value[0];
+ drm_connector_attach_property(connector,
+ sdvo_priv->brightness_property,
+ sdvo_priv->cur_brightness);
+ DRM_DEBUG_KMS("brightness: max %d, "
+ "default %d, current %d\n",
+ data_value[0], data_value[1], response);
+ }
+ }
+ return;
+}
+
bool intel_sdvo_init(struct drm_device *dev, int output_device)
{
struct drm_connector *connector;
drm_mode_connector_attach_encoder(&intel_output->base, &intel_output->enc);
if (sdvo_priv->is_tv)
intel_sdvo_tv_create_property(connector);
+
+ if (sdvo_priv->is_tv || sdvo_priv->is_lvds)
+ intel_sdvo_create_enhance_property(connector);
+
drm_sysfs_connector_add(connector);
intel_sdvo_select_ddc_bus(sdvo_priv);
--- /dev/null
+mkregtable
+*_reg_safe.h
+
#define VGA_RENDER_CONTROL 0x0300
#define VGA_VSTATUS_CNTL_MASK 0x00030000
-/* AVIVO disable VGA rendering */
-static inline void radeon_avivo_vga_render_disable(struct radeon_device *rdev)
-{
- u32 vga_render;
- vga_render = RREG32(VGA_RENDER_CONTROL);
- vga_render &= ~VGA_VSTATUS_CNTL_MASK;
- WREG32(VGA_RENDER_CONTROL, vga_render);
-}
-
#endif
void r100_cs_dump_packet(struct radeon_cs_parser *p,
struct radeon_cs_packet *pkt)
{
- struct radeon_cs_chunk *ib_chunk;
volatile uint32_t *ib;
unsigned i;
unsigned idx;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
idx = pkt->idx;
for (i = 0; i <= (pkt->count + 1); i++, idx++) {
DRM_INFO("ib[%d]=0x%08X\n", idx, ib[idx]);
idx, ib_chunk->length_dw);
return -EINVAL;
}
- header = ib_chunk->kdata[idx];
+ header = radeon_get_ib_value(p, idx);
pkt->idx = idx;
pkt->type = CP_PACKET_GET_TYPE(header);
pkt->count = CP_PACKET_GET_COUNT(header);
*/
int r100_cs_packet_parse_vline(struct radeon_cs_parser *p)
{
- struct radeon_cs_chunk *ib_chunk;
struct drm_mode_object *obj;
struct drm_crtc *crtc;
struct radeon_crtc *radeon_crtc;
int crtc_id;
int r;
uint32_t header, h_idx, reg;
+ volatile uint32_t *ib;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
+ ib = p->ib->ptr;
/* parse the wait until */
r = r100_cs_packet_parse(p, &waitreloc, p->idx);
return r;
}
- if (ib_chunk->kdata[waitreloc.idx + 1] != RADEON_WAIT_CRTC_VLINE) {
+ if (radeon_get_ib_value(p, waitreloc.idx + 1) != RADEON_WAIT_CRTC_VLINE) {
DRM_ERROR("vline wait had illegal wait until\n");
r = -EINVAL;
return r;
}
/* jump over the NOP */
- r = r100_cs_packet_parse(p, &p3reloc, p->idx);
+ r = r100_cs_packet_parse(p, &p3reloc, p->idx + waitreloc.count + 2);
if (r)
return r;
h_idx = p->idx - 2;
- p->idx += waitreloc.count;
- p->idx += p3reloc.count;
+ p->idx += waitreloc.count + 2;
+ p->idx += p3reloc.count + 2;
- header = ib_chunk->kdata[h_idx];
- crtc_id = ib_chunk->kdata[h_idx + 5];
- reg = ib_chunk->kdata[h_idx] >> 2;
+ header = radeon_get_ib_value(p, h_idx);
+ crtc_id = radeon_get_ib_value(p, h_idx + 5);
+ reg = header >> 2;
mutex_lock(&p->rdev->ddev->mode_config.mutex);
obj = drm_mode_object_find(p->rdev->ddev, crtc_id, DRM_MODE_OBJECT_CRTC);
if (!obj) {
if (!crtc->enabled) {
/* if the CRTC isn't enabled - we need to nop out the wait until */
- ib_chunk->kdata[h_idx + 2] = PACKET2(0);
- ib_chunk->kdata[h_idx + 3] = PACKET2(0);
+ ib[h_idx + 2] = PACKET2(0);
+ ib[h_idx + 3] = PACKET2(0);
} else if (crtc_id == 1) {
switch (reg) {
case AVIVO_D1MODE_VLINE_START_END:
- header &= R300_CP_PACKET0_REG_MASK;
+ header &= ~R300_CP_PACKET0_REG_MASK;
header |= AVIVO_D2MODE_VLINE_START_END >> 2;
break;
case RADEON_CRTC_GUI_TRIG_VLINE:
- header &= R300_CP_PACKET0_REG_MASK;
+ header &= ~R300_CP_PACKET0_REG_MASK;
header |= RADEON_CRTC2_GUI_TRIG_VLINE >> 2;
break;
default:
r = -EINVAL;
goto out;
}
- ib_chunk->kdata[h_idx] = header;
- ib_chunk->kdata[h_idx + 3] |= RADEON_ENG_DISPLAY_SELECT_CRTC1;
+ ib[h_idx] = header;
+ ib[h_idx + 3] |= RADEON_ENG_DISPLAY_SELECT_CRTC1;
}
out:
mutex_unlock(&p->rdev->ddev->mode_config.mutex);
int r100_cs_packet_next_reloc(struct radeon_cs_parser *p,
struct radeon_cs_reloc **cs_reloc)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_chunk *relocs_chunk;
struct radeon_cs_packet p3reloc;
unsigned idx;
return -EINVAL;
}
*cs_reloc = NULL;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
relocs_chunk = &p->chunks[p->chunk_relocs_idx];
r = r100_cs_packet_parse(p, &p3reloc, p->idx);
if (r) {
r100_cs_dump_packet(p, &p3reloc);
return -EINVAL;
}
- idx = ib_chunk->kdata[p3reloc.idx + 1];
+ idx = radeon_get_ib_value(p, p3reloc.idx + 1);
if (idx >= relocs_chunk->length_dw) {
DRM_ERROR("Relocs at %d after relocations chunk end %d !\n",
idx, relocs_chunk->length_dw);
struct radeon_cs_packet *pkt,
unsigned idx, unsigned reg)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_reloc *reloc;
struct r100_cs_track *track;
volatile uint32_t *ib;
int r;
int i, face;
u32 tile_flags = 0;
+ u32 idx_value;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
track = (struct r100_cs_track *)p->track;
+ idx_value = radeon_get_ib_value(p, idx);
+
switch (reg) {
case RADEON_CRTC_GUI_TRIG_VLINE:
r = r100_cs_packet_parse_vline(p);
return r;
}
track->zb.robj = reloc->robj;
- track->zb.offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->zb.offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case RADEON_RB3D_COLOROFFSET:
r = r100_cs_packet_next_reloc(p, &reloc);
return r;
}
track->cb[0].robj = reloc->robj;
- track->cb[0].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->cb[0].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case RADEON_PP_TXOFFSET_0:
case RADEON_PP_TXOFFSET_1:
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[i].robj = reloc->robj;
break;
case RADEON_PP_CUBIC_OFFSET_T0_0:
r100_cs_dump_packet(p, pkt);
return r;
}
- track->textures[0].cube_info[i].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->textures[0].cube_info[i].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[0].cube_info[i].robj = reloc->robj;
break;
case RADEON_PP_CUBIC_OFFSET_T1_0:
r100_cs_dump_packet(p, pkt);
return r;
}
- track->textures[1].cube_info[i].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->textures[1].cube_info[i].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[1].cube_info[i].robj = reloc->robj;
break;
case RADEON_PP_CUBIC_OFFSET_T2_0:
r100_cs_dump_packet(p, pkt);
return r;
}
- track->textures[2].cube_info[i].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->textures[2].cube_info[i].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[2].cube_info[i].robj = reloc->robj;
break;
case RADEON_RE_WIDTH_HEIGHT:
- track->maxy = ((ib_chunk->kdata[idx] >> 16) & 0x7FF);
+ track->maxy = ((idx_value >> 16) & 0x7FF);
break;
case RADEON_RB3D_COLORPITCH:
r = r100_cs_packet_next_reloc(p, &reloc);
if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
tile_flags |= RADEON_COLOR_MICROTILE_ENABLE;
- tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+ tmp = idx_value & ~(0x7 << 16);
tmp |= tile_flags;
ib[idx] = tmp;
- track->cb[0].pitch = ib_chunk->kdata[idx] & RADEON_COLORPITCH_MASK;
+ track->cb[0].pitch = idx_value & RADEON_COLORPITCH_MASK;
break;
case RADEON_RB3D_DEPTHPITCH:
- track->zb.pitch = ib_chunk->kdata[idx] & RADEON_DEPTHPITCH_MASK;
+ track->zb.pitch = idx_value & RADEON_DEPTHPITCH_MASK;
break;
case RADEON_RB3D_CNTL:
- switch ((ib_chunk->kdata[idx] >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f) {
+ switch ((idx_value >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f) {
case 7:
case 8:
case 9:
break;
default:
DRM_ERROR("Invalid color buffer format (%d) !\n",
- ((ib_chunk->kdata[idx] >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f));
+ ((idx_value >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f));
return -EINVAL;
}
- track->z_enabled = !!(ib_chunk->kdata[idx] & RADEON_Z_ENABLE);
+ track->z_enabled = !!(idx_value & RADEON_Z_ENABLE);
break;
case RADEON_RB3D_ZSTENCILCNTL:
- switch (ib_chunk->kdata[idx] & 0xf) {
+ switch (idx_value & 0xf) {
case 0:
track->zb.cpp = 2;
break;
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case RADEON_PP_CNTL:
{
- uint32_t temp = ib_chunk->kdata[idx] >> 4;
+ uint32_t temp = idx_value >> 4;
for (i = 0; i < track->num_texture; i++)
track->textures[i].enabled = !!(temp & (1 << i));
}
break;
case RADEON_SE_VF_CNTL:
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = idx_value;
break;
case RADEON_SE_VTX_FMT:
- track->vtx_size = r100_get_vtx_size(ib_chunk->kdata[idx]);
+ track->vtx_size = r100_get_vtx_size(idx_value);
break;
case RADEON_PP_TEX_SIZE_0:
case RADEON_PP_TEX_SIZE_1:
case RADEON_PP_TEX_SIZE_2:
i = (reg - RADEON_PP_TEX_SIZE_0) / 8;
- track->textures[i].width = (ib_chunk->kdata[idx] & RADEON_TEX_USIZE_MASK) + 1;
- track->textures[i].height = ((ib_chunk->kdata[idx] & RADEON_TEX_VSIZE_MASK) >> RADEON_TEX_VSIZE_SHIFT) + 1;
+ track->textures[i].width = (idx_value & RADEON_TEX_USIZE_MASK) + 1;
+ track->textures[i].height = ((idx_value & RADEON_TEX_VSIZE_MASK) >> RADEON_TEX_VSIZE_SHIFT) + 1;
break;
case RADEON_PP_TEX_PITCH_0:
case RADEON_PP_TEX_PITCH_1:
case RADEON_PP_TEX_PITCH_2:
i = (reg - RADEON_PP_TEX_PITCH_0) / 8;
- track->textures[i].pitch = ib_chunk->kdata[idx] + 32;
+ track->textures[i].pitch = idx_value + 32;
break;
case RADEON_PP_TXFILTER_0:
case RADEON_PP_TXFILTER_1:
case RADEON_PP_TXFILTER_2:
i = (reg - RADEON_PP_TXFILTER_0) / 24;
- track->textures[i].num_levels = ((ib_chunk->kdata[idx] & RADEON_MAX_MIP_LEVEL_MASK)
+ track->textures[i].num_levels = ((idx_value & RADEON_MAX_MIP_LEVEL_MASK)
>> RADEON_MAX_MIP_LEVEL_SHIFT);
- tmp = (ib_chunk->kdata[idx] >> 23) & 0x7;
+ tmp = (idx_value >> 23) & 0x7;
if (tmp == 2 || tmp == 6)
track->textures[i].roundup_w = false;
- tmp = (ib_chunk->kdata[idx] >> 27) & 0x7;
+ tmp = (idx_value >> 27) & 0x7;
if (tmp == 2 || tmp == 6)
track->textures[i].roundup_h = false;
break;
case RADEON_PP_TXFORMAT_1:
case RADEON_PP_TXFORMAT_2:
i = (reg - RADEON_PP_TXFORMAT_0) / 24;
- if (ib_chunk->kdata[idx] & RADEON_TXFORMAT_NON_POWER2) {
+ if (idx_value & RADEON_TXFORMAT_NON_POWER2) {
track->textures[i].use_pitch = 1;
} else {
track->textures[i].use_pitch = 0;
- track->textures[i].width = 1 << ((ib_chunk->kdata[idx] >> RADEON_TXFORMAT_WIDTH_SHIFT) & RADEON_TXFORMAT_WIDTH_MASK);
- track->textures[i].height = 1 << ((ib_chunk->kdata[idx] >> RADEON_TXFORMAT_HEIGHT_SHIFT) & RADEON_TXFORMAT_HEIGHT_MASK);
+ track->textures[i].width = 1 << ((idx_value >> RADEON_TXFORMAT_WIDTH_SHIFT) & RADEON_TXFORMAT_WIDTH_MASK);
+ track->textures[i].height = 1 << ((idx_value >> RADEON_TXFORMAT_HEIGHT_SHIFT) & RADEON_TXFORMAT_HEIGHT_MASK);
}
- if (ib_chunk->kdata[idx] & RADEON_TXFORMAT_CUBIC_MAP_ENABLE)
+ if (idx_value & RADEON_TXFORMAT_CUBIC_MAP_ENABLE)
track->textures[i].tex_coord_type = 2;
- switch ((ib_chunk->kdata[idx] & RADEON_TXFORMAT_FORMAT_MASK)) {
+ switch ((idx_value & RADEON_TXFORMAT_FORMAT_MASK)) {
case RADEON_TXFORMAT_I8:
case RADEON_TXFORMAT_RGB332:
case RADEON_TXFORMAT_Y8:
track->textures[i].cpp = 4;
break;
}
- track->textures[i].cube_info[4].width = 1 << ((ib_chunk->kdata[idx] >> 16) & 0xf);
- track->textures[i].cube_info[4].height = 1 << ((ib_chunk->kdata[idx] >> 20) & 0xf);
+ track->textures[i].cube_info[4].width = 1 << ((idx_value >> 16) & 0xf);
+ track->textures[i].cube_info[4].height = 1 << ((idx_value >> 20) & 0xf);
break;
case RADEON_PP_CUBIC_FACES_0:
case RADEON_PP_CUBIC_FACES_1:
case RADEON_PP_CUBIC_FACES_2:
- tmp = ib_chunk->kdata[idx];
+ tmp = idx_value;
i = (reg - RADEON_PP_CUBIC_FACES_0) / 4;
for (face = 0; face < 4; face++) {
track->textures[i].cube_info[face].width = 1 << ((tmp >> (face * 8)) & 0xf);
struct radeon_cs_packet *pkt,
struct radeon_object *robj)
{
- struct radeon_cs_chunk *ib_chunk;
unsigned idx;
-
- ib_chunk = &p->chunks[p->chunk_ib_idx];
+ u32 value;
idx = pkt->idx + 1;
- if ((ib_chunk->kdata[idx+2] + 1) > radeon_object_size(robj)) {
+ value = radeon_get_ib_value(p, idx + 2);
+ if ((value + 1) > radeon_object_size(robj)) {
DRM_ERROR("[drm] Buffer too small for PACKET3 INDX_BUFFER "
"(need %u have %lu) !\n",
- ib_chunk->kdata[idx+2] + 1,
+ value + 1,
radeon_object_size(robj));
return -EINVAL;
}
static int r100_packet3_check(struct radeon_cs_parser *p,
struct radeon_cs_packet *pkt)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_reloc *reloc;
struct r100_cs_track *track;
unsigned idx;
- unsigned i, c;
volatile uint32_t *ib;
int r;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
idx = pkt->idx + 1;
track = (struct r100_cs_track *)p->track;
switch (pkt->opcode) {
case PACKET3_3D_LOAD_VBPNTR:
- c = ib_chunk->kdata[idx++];
- track->num_arrays = c;
- for (i = 0; i < (c - 1); i += 2, idx += 3) {
- r = r100_cs_packet_next_reloc(p, &reloc);
- if (r) {
- DRM_ERROR("No reloc for packet3 %d\n",
- pkt->opcode);
- r100_cs_dump_packet(p, pkt);
- return r;
- }
- ib[idx+1] = ib_chunk->kdata[idx+1] + ((u32)reloc->lobj.gpu_offset);
- track->arrays[i + 0].robj = reloc->robj;
- track->arrays[i + 0].esize = ib_chunk->kdata[idx] >> 8;
- track->arrays[i + 0].esize &= 0x7F;
- r = r100_cs_packet_next_reloc(p, &reloc);
- if (r) {
- DRM_ERROR("No reloc for packet3 %d\n",
- pkt->opcode);
- r100_cs_dump_packet(p, pkt);
- return r;
- }
- ib[idx+2] = ib_chunk->kdata[idx+2] + ((u32)reloc->lobj.gpu_offset);
- track->arrays[i + 1].robj = reloc->robj;
- track->arrays[i + 1].esize = ib_chunk->kdata[idx] >> 24;
- track->arrays[i + 1].esize &= 0x7F;
- }
- if (c & 1) {
- r = r100_cs_packet_next_reloc(p, &reloc);
- if (r) {
- DRM_ERROR("No reloc for packet3 %d\n",
- pkt->opcode);
- r100_cs_dump_packet(p, pkt);
- return r;
- }
- ib[idx+1] = ib_chunk->kdata[idx+1] + ((u32)reloc->lobj.gpu_offset);
- track->arrays[i + 0].robj = reloc->robj;
- track->arrays[i + 0].esize = ib_chunk->kdata[idx] >> 8;
- track->arrays[i + 0].esize &= 0x7F;
- }
+ r = r100_packet3_load_vbpntr(p, pkt, idx);
+ if (r)
+ return r;
break;
case PACKET3_INDX_BUFFER:
r = r100_cs_packet_next_reloc(p, &reloc);
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx+1] = ib_chunk->kdata[idx+1] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx+1] = radeon_get_ib_value(p, idx+1) + ((u32)reloc->lobj.gpu_offset);
r = r100_cs_track_check_pkt3_indx_buffer(p, pkt, reloc->robj);
if (r) {
return r;
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = radeon_get_ib_value(p, idx) + ((u32)reloc->lobj.gpu_offset);
track->num_arrays = 1;
- track->vtx_size = r100_get_vtx_size(ib_chunk->kdata[idx+2]);
+ track->vtx_size = r100_get_vtx_size(radeon_get_ib_value(p, idx + 2));
track->arrays[0].robj = reloc->robj;
track->arrays[0].esize = track->vtx_size;
- track->max_indx = ib_chunk->kdata[idx+1];
+ track->max_indx = radeon_get_ib_value(p, idx+1);
- track->vap_vf_cntl = ib_chunk->kdata[idx+3];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx+3);
track->immd_dwords = pkt->count - 1;
r = r100_cs_track_check(p->rdev, track);
if (r)
return r;
break;
case PACKET3_3D_DRAW_IMMD:
- if (((ib_chunk->kdata[idx+1] >> 4) & 0x3) != 3) {
+ if (((radeon_get_ib_value(p, idx + 1) >> 4) & 0x3) != 3) {
DRM_ERROR("PRIM_WALK must be 3 for IMMD draw\n");
return -EINVAL;
}
- track->vap_vf_cntl = ib_chunk->kdata[idx+1];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx + 1);
track->immd_dwords = pkt->count - 1;
r = r100_cs_track_check(p->rdev, track);
if (r)
break;
/* triggers drawing using in-packet vertex data */
case PACKET3_3D_DRAW_IMMD_2:
- if (((ib_chunk->kdata[idx] >> 4) & 0x3) != 3) {
+ if (((radeon_get_ib_value(p, idx) >> 4) & 0x3) != 3) {
DRM_ERROR("PRIM_WALK must be 3 for IMMD draw\n");
return -EINVAL;
}
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx);
track->immd_dwords = pkt->count;
r = r100_cs_track_check(p->rdev, track);
if (r)
break;
/* triggers drawing using in-packet vertex data */
case PACKET3_3D_DRAW_VBUF_2:
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx);
r = r100_cs_track_check(p->rdev, track);
if (r)
return r;
break;
/* triggers drawing of vertex buffers setup elsewhere */
case PACKET3_3D_DRAW_INDX_2:
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx);
r = r100_cs_track_check(p->rdev, track);
if (r)
return r;
break;
/* triggers drawing using indices to vertex buffer */
case PACKET3_3D_DRAW_VBUF:
- track->vap_vf_cntl = ib_chunk->kdata[idx + 1];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx + 1);
r = r100_cs_track_check(p->rdev, track);
if (r)
return r;
break;
/* triggers drawing of vertex buffers setup elsewhere */
case PACKET3_3D_DRAW_INDX:
- track->vap_vf_cntl = ib_chunk->kdata[idx + 1];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx + 1);
r = r100_cs_track_check(p->rdev, track);
if (r)
return r;
struct radeon_cs_packet *pkt,
unsigned idx, unsigned reg);
+
+
static inline int r100_reloc_pitch_offset(struct radeon_cs_parser *p,
struct radeon_cs_packet *pkt,
unsigned idx,
u32 tile_flags = 0;
u32 tmp;
struct radeon_cs_reloc *reloc;
- struct radeon_cs_chunk *ib_chunk;
-
- ib_chunk = &p->chunks[p->chunk_ib_idx];
+ u32 value;
r = r100_cs_packet_next_reloc(p, &reloc);
if (r) {
r100_cs_dump_packet(p, pkt);
return r;
}
- tmp = ib_chunk->kdata[idx] & 0x003fffff;
+ value = radeon_get_ib_value(p, idx);
+ tmp = value & 0x003fffff;
tmp += (((u32)reloc->lobj.gpu_offset) >> 10);
if (reloc->lobj.tiling_flags & RADEON_TILING_MACRO)
}
tmp |= tile_flags;
- p->ib->ptr[idx] = (ib_chunk->kdata[idx] & 0x3fc00000) | tmp;
+ p->ib->ptr[idx] = (value & 0x3fc00000) | tmp;
return 0;
}
+
+static inline int r100_packet3_load_vbpntr(struct radeon_cs_parser *p,
+ struct radeon_cs_packet *pkt,
+ int idx)
+{
+ unsigned c, i;
+ struct radeon_cs_reloc *reloc;
+ struct r100_cs_track *track;
+ int r = 0;
+ volatile uint32_t *ib;
+ u32 idx_value;
+
+ ib = p->ib->ptr;
+ track = (struct r100_cs_track *)p->track;
+ c = radeon_get_ib_value(p, idx++) & 0x1F;
+ track->num_arrays = c;
+ for (i = 0; i < (c - 1); i+=2, idx+=3) {
+ r = r100_cs_packet_next_reloc(p, &reloc);
+ if (r) {
+ DRM_ERROR("No reloc for packet3 %d\n",
+ pkt->opcode);
+ r100_cs_dump_packet(p, pkt);
+ return r;
+ }
+ idx_value = radeon_get_ib_value(p, idx);
+ ib[idx+1] = radeon_get_ib_value(p, idx + 1) + ((u32)reloc->lobj.gpu_offset);
+
+ track->arrays[i + 0].esize = idx_value >> 8;
+ track->arrays[i + 0].robj = reloc->robj;
+ track->arrays[i + 0].esize &= 0x7F;
+ r = r100_cs_packet_next_reloc(p, &reloc);
+ if (r) {
+ DRM_ERROR("No reloc for packet3 %d\n",
+ pkt->opcode);
+ r100_cs_dump_packet(p, pkt);
+ return r;
+ }
+ ib[idx+2] = radeon_get_ib_value(p, idx + 2) + ((u32)reloc->lobj.gpu_offset);
+ track->arrays[i + 1].robj = reloc->robj;
+ track->arrays[i + 1].esize = idx_value >> 24;
+ track->arrays[i + 1].esize &= 0x7F;
+ }
+ if (c & 1) {
+ r = r100_cs_packet_next_reloc(p, &reloc);
+ if (r) {
+ DRM_ERROR("No reloc for packet3 %d\n",
+ pkt->opcode);
+ r100_cs_dump_packet(p, pkt);
+ return r;
+ }
+ idx_value = radeon_get_ib_value(p, idx);
+ ib[idx+1] = radeon_get_ib_value(p, idx + 1) + ((u32)reloc->lobj.gpu_offset);
+ track->arrays[i + 0].robj = reloc->robj;
+ track->arrays[i + 0].esize = idx_value >> 8;
+ track->arrays[i + 0].esize &= 0x7F;
+ }
+ return r;
+}
struct radeon_cs_packet *pkt,
unsigned idx, unsigned reg)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_reloc *reloc;
struct r100_cs_track *track;
volatile uint32_t *ib;
int i;
int face;
u32 tile_flags = 0;
+ u32 idx_value;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
track = (struct r100_cs_track *)p->track;
-
+ idx_value = radeon_get_ib_value(p, idx);
switch (reg) {
case RADEON_CRTC_GUI_TRIG_VLINE:
r = r100_cs_packet_parse_vline(p);
return r;
}
track->zb.robj = reloc->robj;
- track->zb.offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->zb.offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case RADEON_RB3D_COLOROFFSET:
r = r100_cs_packet_next_reloc(p, &reloc);
return r;
}
track->cb[0].robj = reloc->robj;
- track->cb[0].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->cb[0].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case R200_PP_TXOFFSET_0:
case R200_PP_TXOFFSET_1:
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[i].robj = reloc->robj;
break;
case R200_PP_CUBIC_OFFSET_F1_0:
r100_cs_dump_packet(p, pkt);
return r;
}
- track->textures[i].cube_info[face - 1].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->textures[i].cube_info[face - 1].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[i].cube_info[face - 1].robj = reloc->robj;
break;
case RADEON_RE_WIDTH_HEIGHT:
- track->maxy = ((ib_chunk->kdata[idx] >> 16) & 0x7FF);
+ track->maxy = ((idx_value >> 16) & 0x7FF);
break;
case RADEON_RB3D_COLORPITCH:
r = r100_cs_packet_next_reloc(p, &reloc);
if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
tile_flags |= RADEON_COLOR_MICROTILE_ENABLE;
- tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+ tmp = idx_value & ~(0x7 << 16);
tmp |= tile_flags;
ib[idx] = tmp;
- track->cb[0].pitch = ib_chunk->kdata[idx] & RADEON_COLORPITCH_MASK;
+ track->cb[0].pitch = idx_value & RADEON_COLORPITCH_MASK;
break;
case RADEON_RB3D_DEPTHPITCH:
- track->zb.pitch = ib_chunk->kdata[idx] & RADEON_DEPTHPITCH_MASK;
+ track->zb.pitch = idx_value & RADEON_DEPTHPITCH_MASK;
break;
case RADEON_RB3D_CNTL:
- switch ((ib_chunk->kdata[idx] >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f) {
+ switch ((idx_value >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f) {
case 7:
case 8:
case 9:
break;
default:
DRM_ERROR("Invalid color buffer format (%d) !\n",
- ((ib_chunk->kdata[idx] >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f));
+ ((idx_value >> RADEON_RB3D_COLOR_FORMAT_SHIFT) & 0x1f));
return -EINVAL;
}
- if (ib_chunk->kdata[idx] & RADEON_DEPTHXY_OFFSET_ENABLE) {
+ if (idx_value & RADEON_DEPTHXY_OFFSET_ENABLE) {
DRM_ERROR("No support for depth xy offset in kms\n");
return -EINVAL;
}
- track->z_enabled = !!(ib_chunk->kdata[idx] & RADEON_Z_ENABLE);
+ track->z_enabled = !!(idx_value & RADEON_Z_ENABLE);
break;
case RADEON_RB3D_ZSTENCILCNTL:
- switch (ib_chunk->kdata[idx] & 0xf) {
+ switch (idx_value & 0xf) {
case 0:
track->zb.cpp = 2;
break;
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case RADEON_PP_CNTL:
{
- uint32_t temp = ib_chunk->kdata[idx] >> 4;
+ uint32_t temp = idx_value >> 4;
for (i = 0; i < track->num_texture; i++)
track->textures[i].enabled = !!(temp & (1 << i));
}
break;
case RADEON_SE_VF_CNTL:
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = idx_value;
break;
case 0x210c:
/* VAP_VF_MAX_VTX_INDX */
- track->max_indx = ib_chunk->kdata[idx] & 0x00FFFFFFUL;
+ track->max_indx = idx_value & 0x00FFFFFFUL;
break;
case R200_SE_VTX_FMT_0:
- track->vtx_size = r200_get_vtx_size_0(ib_chunk->kdata[idx]);
+ track->vtx_size = r200_get_vtx_size_0(idx_value);
break;
case R200_SE_VTX_FMT_1:
- track->vtx_size += r200_get_vtx_size_1(ib_chunk->kdata[idx]);
+ track->vtx_size += r200_get_vtx_size_1(idx_value);
break;
case R200_PP_TXSIZE_0:
case R200_PP_TXSIZE_1:
case R200_PP_TXSIZE_4:
case R200_PP_TXSIZE_5:
i = (reg - R200_PP_TXSIZE_0) / 32;
- track->textures[i].width = (ib_chunk->kdata[idx] & RADEON_TEX_USIZE_MASK) + 1;
- track->textures[i].height = ((ib_chunk->kdata[idx] & RADEON_TEX_VSIZE_MASK) >> RADEON_TEX_VSIZE_SHIFT) + 1;
+ track->textures[i].width = (idx_value & RADEON_TEX_USIZE_MASK) + 1;
+ track->textures[i].height = ((idx_value & RADEON_TEX_VSIZE_MASK) >> RADEON_TEX_VSIZE_SHIFT) + 1;
break;
case R200_PP_TXPITCH_0:
case R200_PP_TXPITCH_1:
case R200_PP_TXPITCH_4:
case R200_PP_TXPITCH_5:
i = (reg - R200_PP_TXPITCH_0) / 32;
- track->textures[i].pitch = ib_chunk->kdata[idx] + 32;
+ track->textures[i].pitch = idx_value + 32;
break;
case R200_PP_TXFILTER_0:
case R200_PP_TXFILTER_1:
case R200_PP_TXFILTER_4:
case R200_PP_TXFILTER_5:
i = (reg - R200_PP_TXFILTER_0) / 32;
- track->textures[i].num_levels = ((ib_chunk->kdata[idx] & R200_MAX_MIP_LEVEL_MASK)
+ track->textures[i].num_levels = ((idx_value & R200_MAX_MIP_LEVEL_MASK)
>> R200_MAX_MIP_LEVEL_SHIFT);
- tmp = (ib_chunk->kdata[idx] >> 23) & 0x7;
+ tmp = (idx_value >> 23) & 0x7;
if (tmp == 2 || tmp == 6)
track->textures[i].roundup_w = false;
- tmp = (ib_chunk->kdata[idx] >> 27) & 0x7;
+ tmp = (idx_value >> 27) & 0x7;
if (tmp == 2 || tmp == 6)
track->textures[i].roundup_h = false;
break;
case R200_PP_TXFORMAT_X_4:
case R200_PP_TXFORMAT_X_5:
i = (reg - R200_PP_TXFORMAT_X_0) / 32;
- track->textures[i].txdepth = ib_chunk->kdata[idx] & 0x7;
- tmp = (ib_chunk->kdata[idx] >> 16) & 0x3;
+ track->textures[i].txdepth = idx_value & 0x7;
+ tmp = (idx_value >> 16) & 0x3;
/* 2D, 3D, CUBE */
switch (tmp) {
case 0:
case R200_PP_TXFORMAT_4:
case R200_PP_TXFORMAT_5:
i = (reg - R200_PP_TXFORMAT_0) / 32;
- if (ib_chunk->kdata[idx] & R200_TXFORMAT_NON_POWER2) {
+ if (idx_value & R200_TXFORMAT_NON_POWER2) {
track->textures[i].use_pitch = 1;
} else {
track->textures[i].use_pitch = 0;
- track->textures[i].width = 1 << ((ib_chunk->kdata[idx] >> RADEON_TXFORMAT_WIDTH_SHIFT) & RADEON_TXFORMAT_WIDTH_MASK);
- track->textures[i].height = 1 << ((ib_chunk->kdata[idx] >> RADEON_TXFORMAT_HEIGHT_SHIFT) & RADEON_TXFORMAT_HEIGHT_MASK);
+ track->textures[i].width = 1 << ((idx_value >> RADEON_TXFORMAT_WIDTH_SHIFT) & RADEON_TXFORMAT_WIDTH_MASK);
+ track->textures[i].height = 1 << ((idx_value >> RADEON_TXFORMAT_HEIGHT_SHIFT) & RADEON_TXFORMAT_HEIGHT_MASK);
}
- switch ((ib_chunk->kdata[idx] & RADEON_TXFORMAT_FORMAT_MASK)) {
+ switch ((idx_value & RADEON_TXFORMAT_FORMAT_MASK)) {
case R200_TXFORMAT_I8:
case R200_TXFORMAT_RGB332:
case R200_TXFORMAT_Y8:
track->textures[i].cpp = 4;
break;
}
- track->textures[i].cube_info[4].width = 1 << ((ib_chunk->kdata[idx] >> 16) & 0xf);
- track->textures[i].cube_info[4].height = 1 << ((ib_chunk->kdata[idx] >> 20) & 0xf);
+ track->textures[i].cube_info[4].width = 1 << ((idx_value >> 16) & 0xf);
+ track->textures[i].cube_info[4].height = 1 << ((idx_value >> 20) & 0xf);
break;
case R200_PP_CUBIC_FACES_0:
case R200_PP_CUBIC_FACES_1:
case R200_PP_CUBIC_FACES_3:
case R200_PP_CUBIC_FACES_4:
case R200_PP_CUBIC_FACES_5:
- tmp = ib_chunk->kdata[idx];
+ tmp = idx_value;
i = (reg - R200_PP_CUBIC_FACES_0) / 32;
for (face = 0; face < 4; face++) {
track->textures[i].cube_info[face].width = 1 << ((tmp >> (face * 8)) & 0xf);
struct radeon_cs_packet *pkt,
unsigned idx, unsigned reg)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_reloc *reloc;
struct r100_cs_track *track;
volatile uint32_t *ib;
uint32_t tmp, tile_flags = 0;
unsigned i;
int r;
+ u32 idx_value;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
track = (struct r100_cs_track *)p->track;
+ idx_value = radeon_get_ib_value(p, idx);
+
switch(reg) {
case AVIVO_D1MODE_VLINE_START_END:
case RADEON_CRTC_GUI_TRIG_VLINE:
return r;
}
track->cb[i].robj = reloc->robj;
- track->cb[i].offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->cb[i].offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case R300_ZB_DEPTHOFFSET:
r = r100_cs_packet_next_reloc(p, &reloc);
return r;
}
track->zb.robj = reloc->robj;
- track->zb.offset = ib_chunk->kdata[idx];
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ track->zb.offset = idx_value;
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case R300_TX_OFFSET_0:
case R300_TX_OFFSET_0+4:
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
track->textures[i].robj = reloc->robj;
break;
/* Tracked registers */
case 0x2084:
/* VAP_VF_CNTL */
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = idx_value;
break;
case 0x20B4:
/* VAP_VTX_SIZE */
- track->vtx_size = ib_chunk->kdata[idx] & 0x7F;
+ track->vtx_size = idx_value & 0x7F;
break;
case 0x2134:
/* VAP_VF_MAX_VTX_INDX */
- track->max_indx = ib_chunk->kdata[idx] & 0x00FFFFFFUL;
+ track->max_indx = idx_value & 0x00FFFFFFUL;
break;
case 0x43E4:
/* SC_SCISSOR1 */
- track->maxy = ((ib_chunk->kdata[idx] >> 13) & 0x1FFF) + 1;
+ track->maxy = ((idx_value >> 13) & 0x1FFF) + 1;
if (p->rdev->family < CHIP_RV515) {
track->maxy -= 1440;
}
break;
case 0x4E00:
/* RB3D_CCTL */
- track->num_cb = ((ib_chunk->kdata[idx] >> 5) & 0x3) + 1;
+ track->num_cb = ((idx_value >> 5) & 0x3) + 1;
break;
case 0x4E38:
case 0x4E3C:
if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
tile_flags |= R300_COLOR_MICROTILE_ENABLE;
- tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+ tmp = idx_value & ~(0x7 << 16);
tmp |= tile_flags;
ib[idx] = tmp;
i = (reg - 0x4E38) >> 2;
- track->cb[i].pitch = ib_chunk->kdata[idx] & 0x3FFE;
- switch (((ib_chunk->kdata[idx] >> 21) & 0xF)) {
+ track->cb[i].pitch = idx_value & 0x3FFE;
+ switch (((idx_value >> 21) & 0xF)) {
case 9:
case 11:
case 12:
break;
default:
DRM_ERROR("Invalid color buffer format (%d) !\n",
- ((ib_chunk->kdata[idx] >> 21) & 0xF));
+ ((idx_value >> 21) & 0xF));
return -EINVAL;
}
break;
case 0x4F00:
/* ZB_CNTL */
- if (ib_chunk->kdata[idx] & 2) {
+ if (idx_value & 2) {
track->z_enabled = true;
} else {
track->z_enabled = false;
break;
case 0x4F10:
/* ZB_FORMAT */
- switch ((ib_chunk->kdata[idx] & 0xF)) {
+ switch ((idx_value & 0xF)) {
case 0:
case 1:
track->zb.cpp = 2;
break;
default:
DRM_ERROR("Invalid z buffer format (%d) !\n",
- (ib_chunk->kdata[idx] & 0xF));
+ (idx_value & 0xF));
return -EINVAL;
}
break;
if (reloc->lobj.tiling_flags & RADEON_TILING_MICRO)
tile_flags |= R300_DEPTHMICROTILE_TILED;;
- tmp = ib_chunk->kdata[idx] & ~(0x7 << 16);
+ tmp = idx_value & ~(0x7 << 16);
tmp |= tile_flags;
ib[idx] = tmp;
- track->zb.pitch = ib_chunk->kdata[idx] & 0x3FFC;
+ track->zb.pitch = idx_value & 0x3FFC;
break;
case 0x4104:
for (i = 0; i < 16; i++) {
bool enabled;
- enabled = !!(ib_chunk->kdata[idx] & (1 << i));
+ enabled = !!(idx_value & (1 << i));
track->textures[i].enabled = enabled;
}
break;
case 0x44FC:
/* TX_FORMAT1_[0-15] */
i = (reg - 0x44C0) >> 2;
- tmp = (ib_chunk->kdata[idx] >> 25) & 0x3;
+ tmp = (idx_value >> 25) & 0x3;
track->textures[i].tex_coord_type = tmp;
- switch ((ib_chunk->kdata[idx] & 0x1F)) {
+ switch ((idx_value & 0x1F)) {
case R300_TX_FORMAT_X8:
case R300_TX_FORMAT_Y4X4:
case R300_TX_FORMAT_Z3Y3X2:
break;
default:
DRM_ERROR("Invalid texture format %u\n",
- (ib_chunk->kdata[idx] & 0x1F));
+ (idx_value & 0x1F));
return -EINVAL;
break;
}
case 0x443C:
/* TX_FILTER0_[0-15] */
i = (reg - 0x4400) >> 2;
- tmp = ib_chunk->kdata[idx] & 0x7;
+ tmp = idx_value & 0x7;
if (tmp == 2 || tmp == 4 || tmp == 6) {
track->textures[i].roundup_w = false;
}
- tmp = (ib_chunk->kdata[idx] >> 3) & 0x7;
+ tmp = (idx_value >> 3) & 0x7;
if (tmp == 2 || tmp == 4 || tmp == 6) {
track->textures[i].roundup_h = false;
}
case 0x453C:
/* TX_FORMAT2_[0-15] */
i = (reg - 0x4500) >> 2;
- tmp = ib_chunk->kdata[idx] & 0x3FFF;
+ tmp = idx_value & 0x3FFF;
track->textures[i].pitch = tmp + 1;
if (p->rdev->family >= CHIP_RV515) {
- tmp = ((ib_chunk->kdata[idx] >> 15) & 1) << 11;
+ tmp = ((idx_value >> 15) & 1) << 11;
track->textures[i].width_11 = tmp;
- tmp = ((ib_chunk->kdata[idx] >> 16) & 1) << 11;
+ tmp = ((idx_value >> 16) & 1) << 11;
track->textures[i].height_11 = tmp;
}
break;
case 0x44BC:
/* TX_FORMAT0_[0-15] */
i = (reg - 0x4480) >> 2;
- tmp = ib_chunk->kdata[idx] & 0x7FF;
+ tmp = idx_value & 0x7FF;
track->textures[i].width = tmp + 1;
- tmp = (ib_chunk->kdata[idx] >> 11) & 0x7FF;
+ tmp = (idx_value >> 11) & 0x7FF;
track->textures[i].height = tmp + 1;
- tmp = (ib_chunk->kdata[idx] >> 26) & 0xF;
+ tmp = (idx_value >> 26) & 0xF;
track->textures[i].num_levels = tmp;
- tmp = ib_chunk->kdata[idx] & (1 << 31);
+ tmp = idx_value & (1 << 31);
track->textures[i].use_pitch = !!tmp;
- tmp = (ib_chunk->kdata[idx] >> 22) & 0xF;
+ tmp = (idx_value >> 22) & 0xF;
track->textures[i].txdepth = tmp;
break;
case R300_ZB_ZPASS_ADDR:
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx] = ib_chunk->kdata[idx] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx] = idx_value + ((u32)reloc->lobj.gpu_offset);
break;
case 0x4be8:
/* valid register only on RV530 */
static int r300_packet3_check(struct radeon_cs_parser *p,
struct radeon_cs_packet *pkt)
{
- struct radeon_cs_chunk *ib_chunk;
-
struct radeon_cs_reloc *reloc;
struct r100_cs_track *track;
volatile uint32_t *ib;
unsigned idx;
- unsigned i, c;
int r;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
idx = pkt->idx + 1;
track = (struct r100_cs_track *)p->track;
switch(pkt->opcode) {
case PACKET3_3D_LOAD_VBPNTR:
- c = ib_chunk->kdata[idx++] & 0x1F;
- track->num_arrays = c;
- for (i = 0; i < (c - 1); i+=2, idx+=3) {
- r = r100_cs_packet_next_reloc(p, &reloc);
- if (r) {
- DRM_ERROR("No reloc for packet3 %d\n",
- pkt->opcode);
- r100_cs_dump_packet(p, pkt);
- return r;
- }
- ib[idx+1] = ib_chunk->kdata[idx+1] + ((u32)reloc->lobj.gpu_offset);
- track->arrays[i + 0].robj = reloc->robj;
- track->arrays[i + 0].esize = ib_chunk->kdata[idx] >> 8;
- track->arrays[i + 0].esize &= 0x7F;
- r = r100_cs_packet_next_reloc(p, &reloc);
- if (r) {
- DRM_ERROR("No reloc for packet3 %d\n",
- pkt->opcode);
- r100_cs_dump_packet(p, pkt);
- return r;
- }
- ib[idx+2] = ib_chunk->kdata[idx+2] + ((u32)reloc->lobj.gpu_offset);
- track->arrays[i + 1].robj = reloc->robj;
- track->arrays[i + 1].esize = ib_chunk->kdata[idx] >> 24;
- track->arrays[i + 1].esize &= 0x7F;
- }
- if (c & 1) {
- r = r100_cs_packet_next_reloc(p, &reloc);
- if (r) {
- DRM_ERROR("No reloc for packet3 %d\n",
- pkt->opcode);
- r100_cs_dump_packet(p, pkt);
- return r;
- }
- ib[idx+1] = ib_chunk->kdata[idx+1] + ((u32)reloc->lobj.gpu_offset);
- track->arrays[i + 0].robj = reloc->robj;
- track->arrays[i + 0].esize = ib_chunk->kdata[idx] >> 8;
- track->arrays[i + 0].esize &= 0x7F;
- }
+ r = r100_packet3_load_vbpntr(p, pkt, idx);
+ if (r)
+ return r;
break;
case PACKET3_INDX_BUFFER:
r = r100_cs_packet_next_reloc(p, &reloc);
r100_cs_dump_packet(p, pkt);
return r;
}
- ib[idx+1] = ib_chunk->kdata[idx+1] + ((u32)reloc->lobj.gpu_offset);
+ ib[idx+1] = radeon_get_ib_value(p, idx + 1) + ((u32)reloc->lobj.gpu_offset);
r = r100_cs_track_check_pkt3_indx_buffer(p, pkt, reloc->robj);
if (r) {
return r;
/* Number of dwords is vtx_size * (num_vertices - 1)
* PRIM_WALK must be equal to 3 vertex data in embedded
* in cmd stream */
- if (((ib_chunk->kdata[idx+1] >> 4) & 0x3) != 3) {
+ if (((radeon_get_ib_value(p, idx + 1) >> 4) & 0x3) != 3) {
DRM_ERROR("PRIM_WALK must be 3 for IMMD draw\n");
return -EINVAL;
}
- track->vap_vf_cntl = ib_chunk->kdata[idx+1];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx + 1);
track->immd_dwords = pkt->count - 1;
r = r100_cs_track_check(p->rdev, track);
if (r) {
/* Number of dwords is vtx_size * (num_vertices - 1)
* PRIM_WALK must be equal to 3 vertex data in embedded
* in cmd stream */
- if (((ib_chunk->kdata[idx] >> 4) & 0x3) != 3) {
+ if (((radeon_get_ib_value(p, idx) >> 4) & 0x3) != 3) {
DRM_ERROR("PRIM_WALK must be 3 for IMMD draw\n");
return -EINVAL;
}
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx);
track->immd_dwords = pkt->count;
r = r100_cs_track_check(p->rdev, track);
if (r) {
}
break;
case PACKET3_3D_DRAW_VBUF:
- track->vap_vf_cntl = ib_chunk->kdata[idx + 1];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx + 1);
r = r100_cs_track_check(p->rdev, track);
if (r) {
return r;
}
break;
case PACKET3_3D_DRAW_VBUF_2:
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx);
r = r100_cs_track_check(p->rdev, track);
if (r) {
return r;
}
break;
case PACKET3_3D_DRAW_INDX:
- track->vap_vf_cntl = ib_chunk->kdata[idx + 1];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx + 1);
r = r100_cs_track_check(p->rdev, track);
if (r) {
return r;
}
break;
case PACKET3_3D_DRAW_INDX_2:
- track->vap_vf_cntl = ib_chunk->kdata[idx];
+ track->vap_vf_cntl = radeon_get_ib_value(p, idx);
r = r100_cs_track_check(p->rdev, track);
if (r) {
return r;
#define AVIVO_D1MODE_VBLANK_STATUS 0x6534
# define AVIVO_VBLANK_ACK (1 << 4)
#define AVIVO_D1MODE_VLINE_START_END 0x6538
+#define AVIVO_D1MODE_VLINE_STATUS 0x653c
+# define AVIVO_D1MODE_VLINE_STAT (1 << 12)
#define AVIVO_DxMODE_INT_MASK 0x6540
# define AVIVO_D1MODE_INT_MASK (1 << 0)
# define AVIVO_D2MODE_INT_MASK (1 << 8)
#define AVIVO_D2MODE_VBLANK_STATUS 0x6d34
#define AVIVO_D2MODE_VLINE_START_END 0x6d38
+#define AVIVO_D2MODE_VLINE_STATUS 0x6d3c
#define AVIVO_D2MODE_VIEWPORT_START 0x6d80
#define AVIVO_D2MODE_VIEWPORT_SIZE 0x6d84
#define AVIVO_D2MODE_EXT_OVERSCAN_LEFT_RIGHT 0x6d88
* Jerome Glisse
*/
#include "drmP.h"
-#include "radeon_reg.h"
#include "radeon.h"
+#include "atom.h"
+#include "r520d.h"
-/* r520,rv530,rv560,rv570,r580 depends on : */
-void r100_hdp_reset(struct radeon_device *rdev);
-void r420_pipes_init(struct radeon_device *rdev);
-void rs600_mc_disable_clients(struct radeon_device *rdev);
-void rs600_disable_vga(struct radeon_device *rdev);
-int rv515_debugfs_pipes_info_init(struct radeon_device *rdev);
-int rv515_debugfs_ga_info_init(struct radeon_device *rdev);
+/* This files gather functions specifics to: r520,rv530,rv560,rv570,r580 */
-/* This files gather functions specifics to:
- * r520,rv530,rv560,rv570,r580
- *
- * Some of these functions might be used by newer ASICs.
- */
-void r520_gpu_init(struct radeon_device *rdev);
-int r520_mc_wait_for_idle(struct radeon_device *rdev);
-
-
-/*
- * MC
- */
-int r520_mc_init(struct radeon_device *rdev)
-{
- uint32_t tmp;
- int r;
-
- if (r100_debugfs_rbbm_init(rdev)) {
- DRM_ERROR("Failed to register debugfs file for RBBM !\n");
- }
- if (rv515_debugfs_pipes_info_init(rdev)) {
- DRM_ERROR("Failed to register debugfs file for pipes !\n");
- }
- if (rv515_debugfs_ga_info_init(rdev)) {
- DRM_ERROR("Failed to register debugfs file for pipes !\n");
- }
-
- r520_gpu_init(rdev);
- rv370_pcie_gart_disable(rdev);
-
- /* Setup GPU memory space */
- rdev->mc.vram_location = 0xFFFFFFFFUL;
- rdev->mc.gtt_location = 0xFFFFFFFFUL;
- if (rdev->flags & RADEON_IS_AGP) {
- r = radeon_agp_init(rdev);
- if (r) {
- printk(KERN_WARNING "[drm] Disabling AGP\n");
- rdev->flags &= ~RADEON_IS_AGP;
- rdev->mc.gtt_size = radeon_gart_size * 1024 * 1024;
- } else {
- rdev->mc.gtt_location = rdev->mc.agp_base;
- }
- }
- r = radeon_mc_setup(rdev);
- if (r) {
- return r;
- }
-
- /* Program GPU memory space */
- rs600_mc_disable_clients(rdev);
- if (r520_mc_wait_for_idle(rdev)) {
- printk(KERN_WARNING "Failed to wait MC idle while "
- "programming pipes. Bad things might happen.\n");
- }
- /* Write VRAM size in case we are limiting it */
- WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
- tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
- tmp = REG_SET(R520_MC_FB_TOP, tmp >> 16);
- tmp |= REG_SET(R520_MC_FB_START, rdev->mc.vram_location >> 16);
- WREG32_MC(R520_MC_FB_LOCATION, tmp);
- WREG32(RS690_HDP_FB_LOCATION, rdev->mc.vram_location >> 16);
- WREG32(0x310, rdev->mc.vram_location);
- if (rdev->flags & RADEON_IS_AGP) {
- tmp = rdev->mc.gtt_location + rdev->mc.gtt_size - 1;
- tmp = REG_SET(R520_MC_AGP_TOP, tmp >> 16);
- tmp |= REG_SET(R520_MC_AGP_START, rdev->mc.gtt_location >> 16);
- WREG32_MC(R520_MC_AGP_LOCATION, tmp);
- WREG32_MC(R520_MC_AGP_BASE, rdev->mc.agp_base);
- WREG32_MC(R520_MC_AGP_BASE_2, 0);
- } else {
- WREG32_MC(R520_MC_AGP_LOCATION, 0x0FFFFFFF);
- WREG32_MC(R520_MC_AGP_BASE, 0);
- WREG32_MC(R520_MC_AGP_BASE_2, 0);
- }
- return 0;
-}
-
-void r520_mc_fini(struct radeon_device *rdev)
-{
-}
-
-
-/*
- * Global GPU functions
- */
-void r520_errata(struct radeon_device *rdev)
-{
- rdev->pll_errata = 0;
-}
-
-int r520_mc_wait_for_idle(struct radeon_device *rdev)
+static int r520_mc_wait_for_idle(struct radeon_device *rdev)
{
unsigned i;
uint32_t tmp;
return -1;
}
-void r520_gpu_init(struct radeon_device *rdev)
+static void r520_gpu_init(struct radeon_device *rdev)
{
unsigned pipe_select_current, gb_pipe_select, tmp;
r100_hdp_reset(rdev);
- rs600_disable_vga(rdev);
+ rv515_vga_render_disable(rdev);
/*
* DST_PIPE_CONFIG 0x170C
* GB_TILE_CONFIG 0x4018
}
}
-
-/*
- * VRAM info
- */
static void r520_vram_get_type(struct radeon_device *rdev)
{
uint32_t tmp;
rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a);
}
-void r520_bandwidth_update(struct radeon_device *rdev)
+void r520_mc_program(struct radeon_device *rdev)
+{
+ struct rv515_mc_save save;
+
+ /* Stops all mc clients */
+ rv515_mc_stop(rdev, &save);
+
+ /* Wait for mc idle */
+ if (r520_mc_wait_for_idle(rdev))
+ dev_warn(rdev->dev, "Wait MC idle timeout before updating MC.\n");
+ /* Write VRAM size in case we are limiting it */
+ WREG32(R_0000F8_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
+ /* Program MC, should be a 32bits limited address space */
+ WREG32_MC(R_000004_MC_FB_LOCATION,
+ S_000004_MC_FB_START(rdev->mc.vram_start >> 16) |
+ S_000004_MC_FB_TOP(rdev->mc.vram_end >> 16));
+ WREG32(R_000134_HDP_FB_LOCATION,
+ S_000134_HDP_FB_START(rdev->mc.vram_start >> 16));
+ if (rdev->flags & RADEON_IS_AGP) {
+ WREG32_MC(R_000005_MC_AGP_LOCATION,
+ S_000005_MC_AGP_START(rdev->mc.gtt_start >> 16) |
+ S_000005_MC_AGP_TOP(rdev->mc.gtt_end >> 16));
+ WREG32_MC(R_000006_AGP_BASE, lower_32_bits(rdev->mc.agp_base));
+ WREG32_MC(R_000007_AGP_BASE_2,
+ S_000007_AGP_BASE_ADDR_2(upper_32_bits(rdev->mc.agp_base)));
+ } else {
+ WREG32_MC(R_000005_MC_AGP_LOCATION, 0xFFFFFFFF);
+ WREG32_MC(R_000006_AGP_BASE, 0);
+ WREG32_MC(R_000007_AGP_BASE_2, 0);
+ }
+
+ rv515_mc_resume(rdev, &save);
+}
+
+static int r520_startup(struct radeon_device *rdev)
+{
+ int r;
+
+ r520_mc_program(rdev);
+ /* Resume clock */
+ rv515_clock_startup(rdev);
+ /* Initialize GPU configuration (# pipes, ...) */
+ r520_gpu_init(rdev);
+ /* Initialize GART (initialize after TTM so we can allocate
+ * memory through TTM but finalize after TTM) */
+ if (rdev->flags & RADEON_IS_PCIE) {
+ r = rv370_pcie_gart_enable(rdev);
+ if (r)
+ return r;
+ }
+ /* Enable IRQ */
+ rdev->irq.sw_int = true;
+ r100_irq_set(rdev);
+ /* 1M ring buffer */
+ r = r100_cp_init(rdev, 1024 * 1024);
+ if (r) {
+ dev_err(rdev->dev, "failled initializing CP (%d).\n", r);
+ return r;
+ }
+ r = r100_wb_init(rdev);
+ if (r)
+ dev_err(rdev->dev, "failled initializing WB (%d).\n", r);
+ r = r100_ib_init(rdev);
+ if (r) {
+ dev_err(rdev->dev, "failled initializing IB (%d).\n", r);
+ return r;
+ }
+ return 0;
+}
+
+int r520_resume(struct radeon_device *rdev)
{
- rv515_bandwidth_avivo_update(rdev);
+ /* Make sur GART are not working */
+ if (rdev->flags & RADEON_IS_PCIE)
+ rv370_pcie_gart_disable(rdev);
+ /* Resume clock before doing reset */
+ rv515_clock_startup(rdev);
+ /* Reset gpu before posting otherwise ATOM will enter infinite loop */
+ if (radeon_gpu_reset(rdev)) {
+ dev_warn(rdev->dev, "GPU reset failed ! (0xE40=0x%08X, 0x7C0=0x%08X)\n",
+ RREG32(R_000E40_RBBM_STATUS),
+ RREG32(R_0007C0_CP_STAT));
+ }
+ /* post */
+ atom_asic_init(rdev->mode_info.atom_context);
+ /* Resume clock after posting */
+ rv515_clock_startup(rdev);
+ return r520_startup(rdev);
+}
+
+int r520_init(struct radeon_device *rdev)
+{
+ int r;
+
+ rdev->new_init_path = true;
+ /* Initialize scratch registers */
+ radeon_scratch_init(rdev);
+ /* Initialize surface registers */
+ radeon_surface_init(rdev);
+ /* TODO: disable VGA need to use VGA request */
+ /* BIOS*/
+ if (!radeon_get_bios(rdev)) {
+ if (ASIC_IS_AVIVO(rdev))
+ return -EINVAL;
+ }
+ if (rdev->is_atom_bios) {
+ r = radeon_atombios_init(rdev);
+ if (r)
+ return r;
+ } else {
+ dev_err(rdev->dev, "Expecting atombios for RV515 GPU\n");
+ return -EINVAL;
+ }
+ /* Reset gpu before posting otherwise ATOM will enter infinite loop */
+ if (radeon_gpu_reset(rdev)) {
+ dev_warn(rdev->dev,
+ "GPU reset failed ! (0xE40=0x%08X, 0x7C0=0x%08X)\n",
+ RREG32(R_000E40_RBBM_STATUS),
+ RREG32(R_0007C0_CP_STAT));
+ }
+ /* check if cards are posted or not */
+ if (!radeon_card_posted(rdev) && rdev->bios) {
+ DRM_INFO("GPU not posted. posting now...\n");
+ atom_asic_init(rdev->mode_info.atom_context);
+ }
+ /* Initialize clocks */
+ radeon_get_clock_info(rdev->ddev);
+ /* Get vram informations */
+ r520_vram_info(rdev);
+ /* Initialize memory controller (also test AGP) */
+ r = r420_mc_init(rdev);
+ if (r)
+ return r;
+ rv515_debugfs(rdev);
+ /* Fence driver */
+ r = radeon_fence_driver_init(rdev);
+ if (r)
+ return r;
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ /* Memory manager */
+ r = radeon_object_init(rdev);
+ if (r)
+ return r;
+ r = rv370_pcie_gart_init(rdev);
+ if (r)
+ return r;
+ rv515_set_safe_registers(rdev);
+ rdev->accel_working = true;
+ r = r520_startup(rdev);
+ if (r) {
+ /* Somethings want wront with the accel init stop accel */
+ dev_err(rdev->dev, "Disabling GPU acceleration\n");
+ rv515_suspend(rdev);
+ r100_cp_fini(rdev);
+ r100_wb_fini(rdev);
+ r100_ib_fini(rdev);
+ rv370_pcie_gart_fini(rdev);
+ radeon_agp_fini(rdev);
+ radeon_irq_kms_fini(rdev);
+ rdev->accel_working = false;
+ }
+ return 0;
}
--- /dev/null
+/*
+ * Copyright 2008 Advanced Micro Devices, Inc.
+ * Copyright 2008 Red Hat Inc.
+ * Copyright 2009 Jerome Glisse.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a
+ * copy of this software and associated documentation files (the "Software"),
+ * to deal in the Software without restriction, including without limitation
+ * the rights to use, copy, modify, merge, publish, distribute, sublicense,
+ * and/or sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
+ * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
+ * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Authors: Dave Airlie
+ * Alex Deucher
+ * Jerome Glisse
+ */
+#ifndef __R520D_H__
+#define __R520D_H__
+
+/* Registers */
+#define R_0000F8_CONFIG_MEMSIZE 0x0000F8
+#define S_0000F8_CONFIG_MEMSIZE(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_0000F8_CONFIG_MEMSIZE(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_0000F8_CONFIG_MEMSIZE 0x00000000
+#define R_000134_HDP_FB_LOCATION 0x000134
+#define S_000134_HDP_FB_START(x) (((x) & 0xFFFF) << 0)
+#define G_000134_HDP_FB_START(x) (((x) >> 0) & 0xFFFF)
+#define C_000134_HDP_FB_START 0xFFFF0000
+#define R_0007C0_CP_STAT 0x0007C0
+#define S_0007C0_MRU_BUSY(x) (((x) & 0x1) << 0)
+#define G_0007C0_MRU_BUSY(x) (((x) >> 0) & 0x1)
+#define C_0007C0_MRU_BUSY 0xFFFFFFFE
+#define S_0007C0_MWU_BUSY(x) (((x) & 0x1) << 1)
+#define G_0007C0_MWU_BUSY(x) (((x) >> 1) & 0x1)
+#define C_0007C0_MWU_BUSY 0xFFFFFFFD
+#define S_0007C0_RSIU_BUSY(x) (((x) & 0x1) << 2)
+#define G_0007C0_RSIU_BUSY(x) (((x) >> 2) & 0x1)
+#define C_0007C0_RSIU_BUSY 0xFFFFFFFB
+#define S_0007C0_RCIU_BUSY(x) (((x) & 0x1) << 3)
+#define G_0007C0_RCIU_BUSY(x) (((x) >> 3) & 0x1)
+#define C_0007C0_RCIU_BUSY 0xFFFFFFF7
+#define S_0007C0_CSF_PRIMARY_BUSY(x) (((x) & 0x1) << 9)
+#define G_0007C0_CSF_PRIMARY_BUSY(x) (((x) >> 9) & 0x1)
+#define C_0007C0_CSF_PRIMARY_BUSY 0xFFFFFDFF
+#define S_0007C0_CSF_INDIRECT_BUSY(x) (((x) & 0x1) << 10)
+#define G_0007C0_CSF_INDIRECT_BUSY(x) (((x) >> 10) & 0x1)
+#define C_0007C0_CSF_INDIRECT_BUSY 0xFFFFFBFF
+#define S_0007C0_CSQ_PRIMARY_BUSY(x) (((x) & 0x1) << 11)
+#define G_0007C0_CSQ_PRIMARY_BUSY(x) (((x) >> 11) & 0x1)
+#define C_0007C0_CSQ_PRIMARY_BUSY 0xFFFFF7FF
+#define S_0007C0_CSQ_INDIRECT_BUSY(x) (((x) & 0x1) << 12)
+#define G_0007C0_CSQ_INDIRECT_BUSY(x) (((x) >> 12) & 0x1)
+#define C_0007C0_CSQ_INDIRECT_BUSY 0xFFFFEFFF
+#define S_0007C0_CSI_BUSY(x) (((x) & 0x1) << 13)
+#define G_0007C0_CSI_BUSY(x) (((x) >> 13) & 0x1)
+#define C_0007C0_CSI_BUSY 0xFFFFDFFF
+#define S_0007C0_CSF_INDIRECT2_BUSY(x) (((x) & 0x1) << 14)
+#define G_0007C0_CSF_INDIRECT2_BUSY(x) (((x) >> 14) & 0x1)
+#define C_0007C0_CSF_INDIRECT2_BUSY 0xFFFFBFFF
+#define S_0007C0_CSQ_INDIRECT2_BUSY(x) (((x) & 0x1) << 15)
+#define G_0007C0_CSQ_INDIRECT2_BUSY(x) (((x) >> 15) & 0x1)
+#define C_0007C0_CSQ_INDIRECT2_BUSY 0xFFFF7FFF
+#define S_0007C0_GUIDMA_BUSY(x) (((x) & 0x1) << 28)
+#define G_0007C0_GUIDMA_BUSY(x) (((x) >> 28) & 0x1)
+#define C_0007C0_GUIDMA_BUSY 0xEFFFFFFF
+#define S_0007C0_VIDDMA_BUSY(x) (((x) & 0x1) << 29)
+#define G_0007C0_VIDDMA_BUSY(x) (((x) >> 29) & 0x1)
+#define C_0007C0_VIDDMA_BUSY 0xDFFFFFFF
+#define S_0007C0_CMDSTRM_BUSY(x) (((x) & 0x1) << 30)
+#define G_0007C0_CMDSTRM_BUSY(x) (((x) >> 30) & 0x1)
+#define C_0007C0_CMDSTRM_BUSY 0xBFFFFFFF
+#define S_0007C0_CP_BUSY(x) (((x) & 0x1) << 31)
+#define G_0007C0_CP_BUSY(x) (((x) >> 31) & 0x1)
+#define C_0007C0_CP_BUSY 0x7FFFFFFF
+#define R_000E40_RBBM_STATUS 0x000E40
+#define S_000E40_CMDFIFO_AVAIL(x) (((x) & 0x7F) << 0)
+#define G_000E40_CMDFIFO_AVAIL(x) (((x) >> 0) & 0x7F)
+#define C_000E40_CMDFIFO_AVAIL 0xFFFFFF80
+#define S_000E40_HIRQ_ON_RBB(x) (((x) & 0x1) << 8)
+#define G_000E40_HIRQ_ON_RBB(x) (((x) >> 8) & 0x1)
+#define C_000E40_HIRQ_ON_RBB 0xFFFFFEFF
+#define S_000E40_CPRQ_ON_RBB(x) (((x) & 0x1) << 9)
+#define G_000E40_CPRQ_ON_RBB(x) (((x) >> 9) & 0x1)
+#define C_000E40_CPRQ_ON_RBB 0xFFFFFDFF
+#define S_000E40_CFRQ_ON_RBB(x) (((x) & 0x1) << 10)
+#define G_000E40_CFRQ_ON_RBB(x) (((x) >> 10) & 0x1)
+#define C_000E40_CFRQ_ON_RBB 0xFFFFFBFF
+#define S_000E40_HIRQ_IN_RTBUF(x) (((x) & 0x1) << 11)
+#define G_000E40_HIRQ_IN_RTBUF(x) (((x) >> 11) & 0x1)
+#define C_000E40_HIRQ_IN_RTBUF 0xFFFFF7FF
+#define S_000E40_CPRQ_IN_RTBUF(x) (((x) & 0x1) << 12)
+#define G_000E40_CPRQ_IN_RTBUF(x) (((x) >> 12) & 0x1)
+#define C_000E40_CPRQ_IN_RTBUF 0xFFFFEFFF
+#define S_000E40_CFRQ_IN_RTBUF(x) (((x) & 0x1) << 13)
+#define G_000E40_CFRQ_IN_RTBUF(x) (((x) >> 13) & 0x1)
+#define C_000E40_CFRQ_IN_RTBUF 0xFFFFDFFF
+#define S_000E40_CF_PIPE_BUSY(x) (((x) & 0x1) << 14)
+#define G_000E40_CF_PIPE_BUSY(x) (((x) >> 14) & 0x1)
+#define C_000E40_CF_PIPE_BUSY 0xFFFFBFFF
+#define S_000E40_ENG_EV_BUSY(x) (((x) & 0x1) << 15)
+#define G_000E40_ENG_EV_BUSY(x) (((x) >> 15) & 0x1)
+#define C_000E40_ENG_EV_BUSY 0xFFFF7FFF
+#define S_000E40_CP_CMDSTRM_BUSY(x) (((x) & 0x1) << 16)
+#define G_000E40_CP_CMDSTRM_BUSY(x) (((x) >> 16) & 0x1)
+#define C_000E40_CP_CMDSTRM_BUSY 0xFFFEFFFF
+#define S_000E40_E2_BUSY(x) (((x) & 0x1) << 17)
+#define G_000E40_E2_BUSY(x) (((x) >> 17) & 0x1)
+#define C_000E40_E2_BUSY 0xFFFDFFFF
+#define S_000E40_RB2D_BUSY(x) (((x) & 0x1) << 18)
+#define G_000E40_RB2D_BUSY(x) (((x) >> 18) & 0x1)
+#define C_000E40_RB2D_BUSY 0xFFFBFFFF
+#define S_000E40_RB3D_BUSY(x) (((x) & 0x1) << 19)
+#define G_000E40_RB3D_BUSY(x) (((x) >> 19) & 0x1)
+#define C_000E40_RB3D_BUSY 0xFFF7FFFF
+#define S_000E40_VAP_BUSY(x) (((x) & 0x1) << 20)
+#define G_000E40_VAP_BUSY(x) (((x) >> 20) & 0x1)
+#define C_000E40_VAP_BUSY 0xFFEFFFFF
+#define S_000E40_RE_BUSY(x) (((x) & 0x1) << 21)
+#define G_000E40_RE_BUSY(x) (((x) >> 21) & 0x1)
+#define C_000E40_RE_BUSY 0xFFDFFFFF
+#define S_000E40_TAM_BUSY(x) (((x) & 0x1) << 22)
+#define G_000E40_TAM_BUSY(x) (((x) >> 22) & 0x1)
+#define C_000E40_TAM_BUSY 0xFFBFFFFF
+#define S_000E40_TDM_BUSY(x) (((x) & 0x1) << 23)
+#define G_000E40_TDM_BUSY(x) (((x) >> 23) & 0x1)
+#define C_000E40_TDM_BUSY 0xFF7FFFFF
+#define S_000E40_PB_BUSY(x) (((x) & 0x1) << 24)
+#define G_000E40_PB_BUSY(x) (((x) >> 24) & 0x1)
+#define C_000E40_PB_BUSY 0xFEFFFFFF
+#define S_000E40_TIM_BUSY(x) (((x) & 0x1) << 25)
+#define G_000E40_TIM_BUSY(x) (((x) >> 25) & 0x1)
+#define C_000E40_TIM_BUSY 0xFDFFFFFF
+#define S_000E40_GA_BUSY(x) (((x) & 0x1) << 26)
+#define G_000E40_GA_BUSY(x) (((x) >> 26) & 0x1)
+#define C_000E40_GA_BUSY 0xFBFFFFFF
+#define S_000E40_CBA2D_BUSY(x) (((x) & 0x1) << 27)
+#define G_000E40_CBA2D_BUSY(x) (((x) >> 27) & 0x1)
+#define C_000E40_CBA2D_BUSY 0xF7FFFFFF
+#define S_000E40_RBBM_HIBUSY(x) (((x) & 0x1) << 28)
+#define G_000E40_RBBM_HIBUSY(x) (((x) >> 28) & 0x1)
+#define C_000E40_RBBM_HIBUSY 0xEFFFFFFF
+#define S_000E40_SKID_CFBUSY(x) (((x) & 0x1) << 29)
+#define G_000E40_SKID_CFBUSY(x) (((x) >> 29) & 0x1)
+#define C_000E40_SKID_CFBUSY 0xDFFFFFFF
+#define S_000E40_VAP_VF_BUSY(x) (((x) & 0x1) << 30)
+#define G_000E40_VAP_VF_BUSY(x) (((x) >> 30) & 0x1)
+#define C_000E40_VAP_VF_BUSY 0xBFFFFFFF
+#define S_000E40_GUI_ACTIVE(x) (((x) & 0x1) << 31)
+#define G_000E40_GUI_ACTIVE(x) (((x) >> 31) & 0x1)
+#define C_000E40_GUI_ACTIVE 0x7FFFFFFF
+
+
+#define R_000004_MC_FB_LOCATION 0x000004
+#define S_000004_MC_FB_START(x) (((x) & 0xFFFF) << 0)
+#define G_000004_MC_FB_START(x) (((x) >> 0) & 0xFFFF)
+#define C_000004_MC_FB_START 0xFFFF0000
+#define S_000004_MC_FB_TOP(x) (((x) & 0xFFFF) << 16)
+#define G_000004_MC_FB_TOP(x) (((x) >> 16) & 0xFFFF)
+#define C_000004_MC_FB_TOP 0x0000FFFF
+#define R_000005_MC_AGP_LOCATION 0x000005
+#define S_000005_MC_AGP_START(x) (((x) & 0xFFFF) << 0)
+#define G_000005_MC_AGP_START(x) (((x) >> 0) & 0xFFFF)
+#define C_000005_MC_AGP_START 0xFFFF0000
+#define S_000005_MC_AGP_TOP(x) (((x) & 0xFFFF) << 16)
+#define G_000005_MC_AGP_TOP(x) (((x) >> 16) & 0xFFFF)
+#define C_000005_MC_AGP_TOP 0x0000FFFF
+#define R_000006_AGP_BASE 0x000006
+#define S_000006_AGP_BASE_ADDR(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_000006_AGP_BASE_ADDR(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_000006_AGP_BASE_ADDR 0x00000000
+#define R_000007_AGP_BASE_2 0x000007
+#define S_000007_AGP_BASE_ADDR_2(x) (((x) & 0xF) << 0)
+#define G_000007_AGP_BASE_ADDR_2(x) (((x) >> 0) & 0xF)
+#define C_000007_AGP_BASE_ADDR_2 0xFFFFFFF0
+
+#endif
#include "radeon.h"
#include "radeon_mode.h"
#include "r600d.h"
-#include "avivod.h"
#include "atom.h"
+#include "avivod.h"
#define PFP_UCODE_SIZE 576
#define PM4_UCODE_SIZE 1792
/* we need to own VRAM, so turn off the VGA renderer here
* to stop it overwriting our objects */
- radeon_avivo_vga_render_disable(rdev);
+ rv515_vga_render_disable(rdev);
}
int r600_mc_init(struct radeon_device *rdev)
/* Setup GPU memory space */
rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE);
rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE);
+
+ if (rdev->mc.mc_vram_size > rdev->mc.aper_size)
+ rdev->mc.mc_vram_size = rdev->mc.aper_size;
+
+ if (rdev->mc.real_vram_size > rdev->mc.aper_size)
+ rdev->mc.real_vram_size = rdev->mc.aper_size;
+
if (rdev->flags & RADEON_IS_AGP) {
r = radeon_agp_init(rdev);
if (r)
#include "drmP.h"
#include "radeon.h"
#include "r600d.h"
-#include "avivod.h"
static int r600_cs_packet_next_reloc_mm(struct radeon_cs_parser *p,
struct radeon_cs_reloc **cs_reloc);
idx, ib_chunk->length_dw);
return -EINVAL;
}
- header = ib_chunk->kdata[idx];
+ header = radeon_get_ib_value(p, idx);
pkt->idx = idx;
pkt->type = CP_PACKET_GET_TYPE(header);
pkt->count = CP_PACKET_GET_COUNT(header);
static int r600_cs_packet_next_reloc_mm(struct radeon_cs_parser *p,
struct radeon_cs_reloc **cs_reloc)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_chunk *relocs_chunk;
struct radeon_cs_packet p3reloc;
unsigned idx;
return -EINVAL;
}
*cs_reloc = NULL;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
relocs_chunk = &p->chunks[p->chunk_relocs_idx];
r = r600_cs_packet_parse(p, &p3reloc, p->idx);
if (r) {
p3reloc.idx);
return -EINVAL;
}
- idx = ib_chunk->kdata[p3reloc.idx + 1];
+ idx = radeon_get_ib_value(p, p3reloc.idx + 1);
if (idx >= relocs_chunk->length_dw) {
DRM_ERROR("Relocs at %d after relocations chunk end %d !\n",
idx, relocs_chunk->length_dw);
static int r600_cs_packet_next_reloc_nomm(struct radeon_cs_parser *p,
struct radeon_cs_reloc **cs_reloc)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_chunk *relocs_chunk;
struct radeon_cs_packet p3reloc;
unsigned idx;
return -EINVAL;
}
*cs_reloc = NULL;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
relocs_chunk = &p->chunks[p->chunk_relocs_idx];
r = r600_cs_packet_parse(p, &p3reloc, p->idx);
if (r) {
p3reloc.idx);
return -EINVAL;
}
- idx = ib_chunk->kdata[p3reloc.idx + 1];
+ idx = radeon_get_ib_value(p, p3reloc.idx + 1);
if (idx >= relocs_chunk->length_dw) {
DRM_ERROR("Relocs at %d after relocations chunk end %d !\n",
idx, relocs_chunk->length_dw);
return 0;
}
+/**
+ * r600_cs_packet_next_vline() - parse userspace VLINE packet
+ * @parser: parser structure holding parsing context.
+ *
+ * Userspace sends a special sequence for VLINE waits.
+ * PACKET0 - VLINE_START_END + value
+ * PACKET3 - WAIT_REG_MEM poll vline status reg
+ * RELOC (P3) - crtc_id in reloc.
+ *
+ * This function parses this and relocates the VLINE START END
+ * and WAIT_REG_MEM packets to the correct crtc.
+ * It also detects a switched off crtc and nulls out the
+ * wait in that case.
+ */
+static int r600_cs_packet_parse_vline(struct radeon_cs_parser *p)
+{
+ struct drm_mode_object *obj;
+ struct drm_crtc *crtc;
+ struct radeon_crtc *radeon_crtc;
+ struct radeon_cs_packet p3reloc, wait_reg_mem;
+ int crtc_id;
+ int r;
+ uint32_t header, h_idx, reg, wait_reg_mem_info;
+ volatile uint32_t *ib;
+
+ ib = p->ib->ptr;
+
+ /* parse the WAIT_REG_MEM */
+ r = r600_cs_packet_parse(p, &wait_reg_mem, p->idx);
+ if (r)
+ return r;
+
+ /* check its a WAIT_REG_MEM */
+ if (wait_reg_mem.type != PACKET_TYPE3 ||
+ wait_reg_mem.opcode != PACKET3_WAIT_REG_MEM) {
+ DRM_ERROR("vline wait missing WAIT_REG_MEM segment\n");
+ r = -EINVAL;
+ return r;
+ }
+
+ wait_reg_mem_info = radeon_get_ib_value(p, wait_reg_mem.idx + 1);
+ /* bit 4 is reg (0) or mem (1) */
+ if (wait_reg_mem_info & 0x10) {
+ DRM_ERROR("vline WAIT_REG_MEM waiting on MEM rather than REG\n");
+ r = -EINVAL;
+ return r;
+ }
+ /* waiting for value to be equal */
+ if ((wait_reg_mem_info & 0x7) != 0x3) {
+ DRM_ERROR("vline WAIT_REG_MEM function not equal\n");
+ r = -EINVAL;
+ return r;
+ }
+ if ((radeon_get_ib_value(p, wait_reg_mem.idx + 2) << 2) != AVIVO_D1MODE_VLINE_STATUS) {
+ DRM_ERROR("vline WAIT_REG_MEM bad reg\n");
+ r = -EINVAL;
+ return r;
+ }
+
+ if (radeon_get_ib_value(p, wait_reg_mem.idx + 5) != AVIVO_D1MODE_VLINE_STAT) {
+ DRM_ERROR("vline WAIT_REG_MEM bad bit mask\n");
+ r = -EINVAL;
+ return r;
+ }
+
+ /* jump over the NOP */
+ r = r600_cs_packet_parse(p, &p3reloc, p->idx + wait_reg_mem.count + 2);
+ if (r)
+ return r;
+
+ h_idx = p->idx - 2;
+ p->idx += wait_reg_mem.count + 2;
+ p->idx += p3reloc.count + 2;
+
+ header = radeon_get_ib_value(p, h_idx);
+ crtc_id = radeon_get_ib_value(p, h_idx + 2 + 7 + 1);
+ reg = header >> 2;
+ mutex_lock(&p->rdev->ddev->mode_config.mutex);
+ obj = drm_mode_object_find(p->rdev->ddev, crtc_id, DRM_MODE_OBJECT_CRTC);
+ if (!obj) {
+ DRM_ERROR("cannot find crtc %d\n", crtc_id);
+ r = -EINVAL;
+ goto out;
+ }
+ crtc = obj_to_crtc(obj);
+ radeon_crtc = to_radeon_crtc(crtc);
+ crtc_id = radeon_crtc->crtc_id;
+
+ if (!crtc->enabled) {
+ /* if the CRTC isn't enabled - we need to nop out the WAIT_REG_MEM */
+ ib[h_idx + 2] = PACKET2(0);
+ ib[h_idx + 3] = PACKET2(0);
+ ib[h_idx + 4] = PACKET2(0);
+ ib[h_idx + 5] = PACKET2(0);
+ ib[h_idx + 6] = PACKET2(0);
+ ib[h_idx + 7] = PACKET2(0);
+ ib[h_idx + 8] = PACKET2(0);
+ } else if (crtc_id == 1) {
+ switch (reg) {
+ case AVIVO_D1MODE_VLINE_START_END:
+ header &= ~R600_CP_PACKET0_REG_MASK;
+ header |= AVIVO_D2MODE_VLINE_START_END >> 2;
+ break;
+ default:
+ DRM_ERROR("unknown crtc reloc\n");
+ r = -EINVAL;
+ goto out;
+ }
+ ib[h_idx] = header;
+ ib[h_idx + 4] = AVIVO_D2MODE_VLINE_STATUS >> 2;
+ }
+out:
+ mutex_unlock(&p->rdev->ddev->mode_config.mutex);
+ return r;
+}
+
static int r600_packet0_check(struct radeon_cs_parser *p,
struct radeon_cs_packet *pkt,
unsigned idx, unsigned reg)
{
+ int r;
+
switch (reg) {
case AVIVO_D1MODE_VLINE_START_END:
- case AVIVO_D2MODE_VLINE_START_END:
+ r = r600_cs_packet_parse_vline(p);
+ if (r) {
+ DRM_ERROR("No reloc for ib[%d]=0x%04X\n",
+ idx, reg);
+ return r;
+ }
break;
default:
printk(KERN_ERR "Forbidden register 0x%04X in cs at %d\n",
static int r600_packet3_check(struct radeon_cs_parser *p,
struct radeon_cs_packet *pkt)
{
- struct radeon_cs_chunk *ib_chunk;
struct radeon_cs_reloc *reloc;
volatile u32 *ib;
unsigned idx;
unsigned i;
unsigned start_reg, end_reg, reg;
int r;
+ u32 idx_value;
ib = p->ib->ptr;
- ib_chunk = &p->chunks[p->chunk_ib_idx];
idx = pkt->idx + 1;
+ idx_value = radeon_get_ib_value(p, idx);
+
switch (pkt->opcode) {
case PACKET3_START_3D_CMDBUF:
if (p->family >= CHIP_RV770 || pkt->count) {
DRM_ERROR("bad DRAW_INDEX\n");
return -EINVAL;
}
- ib[idx+0] += (u32)(reloc->lobj.gpu_offset & 0xffffffff);
- ib[idx+1] = upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
+ ib[idx+0] = idx_value + (u32)(reloc->lobj.gpu_offset & 0xffffffff);
+ ib[idx+1] += upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
break;
case PACKET3_DRAW_INDEX_AUTO:
if (pkt->count != 1) {
return -EINVAL;
}
/* bit 4 is reg (0) or mem (1) */
- if (ib_chunk->kdata[idx+0] & 0x10) {
+ if (idx_value & 0x10) {
r = r600_cs_packet_next_reloc(p, &reloc);
if (r) {
DRM_ERROR("bad WAIT_REG_MEM\n");
return -EINVAL;
}
ib[idx+1] += (u32)(reloc->lobj.gpu_offset & 0xffffffff);
- ib[idx+2] = upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
+ ib[idx+2] += upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
}
break;
case PACKET3_SURFACE_SYNC:
return -EINVAL;
}
/* 0xffffffff/0x0 is flush all cache flag */
- if (ib_chunk->kdata[idx+1] != 0xffffffff ||
- ib_chunk->kdata[idx+2] != 0) {
+ if (radeon_get_ib_value(p, idx + 1) != 0xffffffff ||
+ radeon_get_ib_value(p, idx + 2) != 0) {
r = r600_cs_packet_next_reloc(p, &reloc);
if (r) {
DRM_ERROR("bad SURFACE_SYNC\n");
return -EINVAL;
}
ib[idx+1] += (u32)(reloc->lobj.gpu_offset & 0xffffffff);
- ib[idx+2] |= upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
+ ib[idx+2] += upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
}
break;
case PACKET3_EVENT_WRITE_EOP:
return -EINVAL;
}
ib[idx+1] += (u32)(reloc->lobj.gpu_offset & 0xffffffff);
- ib[idx+2] |= upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
+ ib[idx+2] += upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
break;
case PACKET3_SET_CONFIG_REG:
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_CONFIG_REG_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_CONFIG_REG_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_CONFIG_REG_OFFSET) ||
(start_reg >= PACKET3_SET_CONFIG_REG_END) ||
}
break;
case PACKET3_SET_CONTEXT_REG:
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_CONTEXT_REG_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_CONTEXT_REG_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_CONTEXT_REG_OFFSET) ||
(start_reg >= PACKET3_SET_CONTEXT_REG_END) ||
DRM_ERROR("bad SET_RESOURCE\n");
return -EINVAL;
}
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_RESOURCE_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_RESOURCE_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_RESOURCE_OFFSET) ||
(start_reg >= PACKET3_SET_RESOURCE_END) ||
return -EINVAL;
}
for (i = 0; i < (pkt->count / 7); i++) {
- switch (G__SQ_VTX_CONSTANT_TYPE(ib[idx+(i*7)+6+1])) {
+ switch (G__SQ_VTX_CONSTANT_TYPE(radeon_get_ib_value(p, idx+(i*7)+6+1))) {
case SQ_TEX_VTX_VALID_TEXTURE:
/* tex base */
r = r600_cs_packet_next_reloc(p, &reloc);
return -EINVAL;
}
ib[idx+1+(i*7)+0] += (u32)((reloc->lobj.gpu_offset) & 0xffffffff);
- ib[idx+1+(i*7)+2] |= upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
+ ib[idx+1+(i*7)+2] += upper_32_bits(reloc->lobj.gpu_offset) & 0xff;
break;
case SQ_TEX_VTX_INVALID_TEXTURE:
case SQ_TEX_VTX_INVALID_BUFFER:
}
break;
case PACKET3_SET_ALU_CONST:
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_ALU_CONST_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_ALU_CONST_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_ALU_CONST_OFFSET) ||
(start_reg >= PACKET3_SET_ALU_CONST_END) ||
}
break;
case PACKET3_SET_BOOL_CONST:
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_BOOL_CONST_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_BOOL_CONST_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_BOOL_CONST_OFFSET) ||
(start_reg >= PACKET3_SET_BOOL_CONST_END) ||
}
break;
case PACKET3_SET_LOOP_CONST:
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_LOOP_CONST_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_LOOP_CONST_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_LOOP_CONST_OFFSET) ||
(start_reg >= PACKET3_SET_LOOP_CONST_END) ||
}
break;
case PACKET3_SET_CTL_CONST:
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_CTL_CONST_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_CTL_CONST_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_CTL_CONST_OFFSET) ||
(start_reg >= PACKET3_SET_CTL_CONST_END) ||
DRM_ERROR("bad SET_SAMPLER\n");
return -EINVAL;
}
- start_reg = (ib[idx+0] << 2) + PACKET3_SET_SAMPLER_OFFSET;
+ start_reg = (idx_value << 2) + PACKET3_SET_SAMPLER_OFFSET;
end_reg = 4 * pkt->count + start_reg - 4;
if ((start_reg < PACKET3_SET_SAMPLER_OFFSET) ||
(start_reg >= PACKET3_SET_SAMPLER_END) ||
kfree(parser->relocs);
for (i = 0; i < parser->nchunks; i++) {
kfree(parser->chunks[i].kdata);
+ kfree(parser->chunks[i].kpage[0]);
+ kfree(parser->chunks[i].kpage[1]);
}
kfree(parser->chunks);
kfree(parser->chunks_array);
* uncached). */
ib_chunk = &parser.chunks[parser.chunk_ib_idx];
parser.ib->length_dw = ib_chunk->length_dw;
- memcpy((void *)parser.ib->ptr, ib_chunk->kdata, ib_chunk->length_dw*4);
*l = parser.ib->length_dw;
r = r600_cs_parse(&parser);
if (r) {
r600_cs_parser_fini(&parser, r);
return r;
}
+ r = radeon_cs_finish_pages(&parser);
+ if (r) {
+ DRM_ERROR("Invalid command stream !\n");
+ r600_cs_parser_fini(&parser, r);
+ return r;
+ }
r600_cs_parser_fini(&parser, r);
return r;
}
* - TESTING, TESTING, TESTING
*/
+/* Initialization path:
+ * We expect that acceleration initialization might fail for various
+ * reasons even thought we work hard to make it works on most
+ * configurations. In order to still have a working userspace in such
+ * situation the init path must succeed up to the memory controller
+ * initialization point. Failure before this point are considered as
+ * fatal error. Here is the init callchain :
+ * radeon_device_init perform common structure, mutex initialization
+ * asic_init setup the GPU memory layout and perform all
+ * one time initialization (failure in this
+ * function are considered fatal)
+ * asic_startup setup the GPU acceleration, in order to
+ * follow guideline the first thing this
+ * function should do is setting the GPU
+ * memory controller (only MC setup failure
+ * are considered as fatal)
+ */
+
#include <asm/atomic.h>
#include <linux/wait.h>
#include <linux/list.h>
unsigned long idx;
uint64_t gpu_addr;
struct radeon_fence *fence;
- volatile uint32_t *ptr;
+ uint32_t *ptr;
uint32_t length_dw;
};
struct radeon_cs_chunk {
uint32_t chunk_id;
uint32_t length_dw;
+ int kpage_idx[2];
+ uint32_t *kpage[2];
uint32_t *kdata;
+ void __user *user_ptr;
+ int last_copied_page;
+ int last_page_index;
};
struct radeon_cs_parser {
struct radeon_ib *ib;
void *track;
unsigned family;
+ int parser_error;
};
+extern int radeon_cs_update_pages(struct radeon_cs_parser *p, int pg_idx);
+extern int radeon_cs_finish_pages(struct radeon_cs_parser *p);
+
+
+static inline u32 radeon_get_ib_value(struct radeon_cs_parser *p, int idx)
+{
+ struct radeon_cs_chunk *ibc = &p->chunks[p->chunk_ib_idx];
+ u32 pg_idx, pg_offset;
+ u32 idx_value = 0;
+ int new_page;
+
+ pg_idx = (idx * 4) / PAGE_SIZE;
+ pg_offset = (idx * 4) % PAGE_SIZE;
+
+ if (ibc->kpage_idx[0] == pg_idx)
+ return ibc->kpage[0][pg_offset/4];
+ if (ibc->kpage_idx[1] == pg_idx)
+ return ibc->kpage[1][pg_offset/4];
+
+ new_page = radeon_cs_update_pages(p, pg_idx);
+ if (new_page < 0) {
+ p->parser_error = new_page;
+ return 0;
+ }
+
+ idx_value = ibc->kpage[new_page][pg_offset/4];
+ return idx_value;
+}
+
struct radeon_cs_packet {
unsigned idx;
unsigned type;
extern void radeon_scratch_init(struct radeon_device *rdev);
extern void radeon_surface_init(struct radeon_device *rdev);
extern int radeon_cs_parser_init(struct radeon_cs_parser *p, void *data);
+extern void radeon_atom_set_clock_gating(struct radeon_device *rdev, int enable);
/* r100,rv100,rs100,rv200,rs200,r200,rv250,rs300,rv280 */
struct r100_mc_save {
extern void r100_wb_disable(struct radeon_device *rdev);
extern void r100_wb_fini(struct radeon_device *rdev);
extern int r100_wb_init(struct radeon_device *rdev);
+extern void r100_hdp_reset(struct radeon_device *rdev);
+extern int r100_rb2d_reset(struct radeon_device *rdev);
+extern int r100_cp_reset(struct radeon_device *rdev);
/* r300,r350,rv350,rv370,rv380 */
extern void r300_set_reg_safe(struct radeon_device *rdev);
extern void rv370_pcie_gart_disable(struct radeon_device *rdev);
/* r420,r423,rv410 */
+extern int r420_mc_init(struct radeon_device *rdev);
extern u32 r420_mc_rreg(struct radeon_device *rdev, u32 reg);
extern void r420_mc_wreg(struct radeon_device *rdev, u32 reg, u32 v);
extern int r420_debugfs_pipes_info_init(struct radeon_device *rdev);
+extern void r420_pipes_init(struct radeon_device *rdev);
/* rv515 */
+struct rv515_mc_save {
+ u32 d1vga_control;
+ u32 d2vga_control;
+ u32 vga_render_control;
+ u32 vga_hdp_control;
+ u32 d1crtc_control;
+ u32 d2crtc_control;
+};
extern void rv515_bandwidth_avivo_update(struct radeon_device *rdev);
+extern void rv515_vga_render_disable(struct radeon_device *rdev);
+extern void rv515_set_safe_registers(struct radeon_device *rdev);
+extern void rv515_mc_stop(struct radeon_device *rdev, struct rv515_mc_save *save);
+extern void rv515_mc_resume(struct radeon_device *rdev, struct rv515_mc_save *save);
+extern void rv515_clock_startup(struct radeon_device *rdev);
+extern void rv515_debugfs(struct radeon_device *rdev);
+extern int rv515_suspend(struct radeon_device *rdev);
/* rs690, rs740 */
extern void rs690_line_buffer_adjust(struct radeon_device *rdev,
* rv515
*/
int rv515_init(struct radeon_device *rdev);
-void rv515_errata(struct radeon_device *rdev);
-void rv515_vram_info(struct radeon_device *rdev);
+void rv515_fini(struct radeon_device *rdev);
int rv515_gpu_reset(struct radeon_device *rdev);
-int rv515_mc_init(struct radeon_device *rdev);
-void rv515_mc_fini(struct radeon_device *rdev);
uint32_t rv515_mc_rreg(struct radeon_device *rdev, uint32_t reg);
void rv515_mc_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
void rv515_ring_start(struct radeon_device *rdev);
uint32_t rv515_pcie_rreg(struct radeon_device *rdev, uint32_t reg);
void rv515_pcie_wreg(struct radeon_device *rdev, uint32_t reg, uint32_t v);
void rv515_bandwidth_update(struct radeon_device *rdev);
+int rv515_resume(struct radeon_device *rdev);
+int rv515_suspend(struct radeon_device *rdev);
static struct radeon_asic rv515_asic = {
.init = &rv515_init,
- .errata = &rv515_errata,
- .vram_info = &rv515_vram_info,
+ .fini = &rv515_fini,
+ .suspend = &rv515_suspend,
+ .resume = &rv515_resume,
+ .errata = NULL,
+ .vram_info = NULL,
.vga_set_state = &r100_vga_set_state,
.gpu_reset = &rv515_gpu_reset,
- .mc_init = &rv515_mc_init,
- .mc_fini = &rv515_mc_fini,
- .wb_init = &r100_wb_init,
- .wb_fini = &r100_wb_fini,
+ .mc_init = NULL,
+ .mc_fini = NULL,
+ .wb_init = NULL,
+ .wb_fini = NULL,
.gart_init = &rv370_pcie_gart_init,
.gart_fini = &rv370_pcie_gart_fini,
- .gart_enable = &rv370_pcie_gart_enable,
- .gart_disable = &rv370_pcie_gart_disable,
+ .gart_enable = NULL,
+ .gart_disable = NULL,
.gart_tlb_flush = &rv370_pcie_gart_tlb_flush,
.gart_set_page = &rv370_pcie_gart_set_page,
- .cp_init = &r100_cp_init,
- .cp_fini = &r100_cp_fini,
- .cp_disable = &r100_cp_disable,
+ .cp_init = NULL,
+ .cp_fini = NULL,
+ .cp_disable = NULL,
.cp_commit = &r100_cp_commit,
.ring_start = &rv515_ring_start,
.ring_test = &r100_ring_test,
.ring_ib_execute = &r100_ring_ib_execute,
- .ib_test = &r100_ib_test,
+ .ib_test = NULL,
.irq_set = &rs600_irq_set,
.irq_process = &rs600_irq_process,
.get_vblank_counter = &rs600_get_vblank_counter,
/*
* r520,rv530,rv560,rv570,r580
*/
-void r520_errata(struct radeon_device *rdev);
-void r520_vram_info(struct radeon_device *rdev);
-int r520_mc_init(struct radeon_device *rdev);
-void r520_mc_fini(struct radeon_device *rdev);
-void r520_bandwidth_update(struct radeon_device *rdev);
+int r520_init(struct radeon_device *rdev);
+int r520_resume(struct radeon_device *rdev);
static struct radeon_asic r520_asic = {
- .init = &rv515_init,
- .errata = &r520_errata,
- .vram_info = &r520_vram_info,
+ .init = &r520_init,
+ .fini = &rv515_fini,
+ .suspend = &rv515_suspend,
+ .resume = &r520_resume,
+ .errata = NULL,
+ .vram_info = NULL,
.vga_set_state = &r100_vga_set_state,
.gpu_reset = &rv515_gpu_reset,
- .mc_init = &r520_mc_init,
- .mc_fini = &r520_mc_fini,
- .wb_init = &r100_wb_init,
- .wb_fini = &r100_wb_fini,
- .gart_init = &rv370_pcie_gart_init,
- .gart_fini = &rv370_pcie_gart_fini,
- .gart_enable = &rv370_pcie_gart_enable,
- .gart_disable = &rv370_pcie_gart_disable,
+ .mc_init = NULL,
+ .mc_fini = NULL,
+ .wb_init = NULL,
+ .wb_fini = NULL,
+ .gart_init = NULL,
+ .gart_fini = NULL,
+ .gart_enable = NULL,
+ .gart_disable = NULL,
.gart_tlb_flush = &rv370_pcie_gart_tlb_flush,
.gart_set_page = &rv370_pcie_gart_set_page,
- .cp_init = &r100_cp_init,
- .cp_fini = &r100_cp_fini,
- .cp_disable = &r100_cp_disable,
+ .cp_init = NULL,
+ .cp_fini = NULL,
+ .cp_disable = NULL,
.cp_commit = &r100_cp_commit,
.ring_start = &rv515_ring_start,
.ring_test = &r100_ring_test,
.ring_ib_execute = &r100_ring_ib_execute,
- .ib_test = &r100_ib_test,
+ .ib_test = NULL,
.irq_set = &rs600_irq_set,
.irq_process = &rs600_irq_process,
.get_vblank_counter = &rs600_get_vblank_counter,
.set_clock_gating = &radeon_atom_set_clock_gating,
.set_surface_reg = r100_set_surface_reg,
.clear_surface_reg = r100_clear_surface_reg,
- .bandwidth_update = &r520_bandwidth_update,
+ .bandwidth_update = &rv515_bandwidth_update,
};
/*
.set_clock_gating = &radeon_atom_set_clock_gating,
.set_surface_reg = r600_set_surface_reg,
.clear_surface_reg = r600_clear_surface_reg,
- .bandwidth_update = &r520_bandwidth_update,
+ .bandwidth_update = &rv515_bandwidth_update,
};
/*
.set_clock_gating = &radeon_atom_set_clock_gating,
.set_surface_reg = r600_set_surface_reg,
.clear_surface_reg = r600_clear_surface_reg,
- .bandwidth_update = &r520_bandwidth_update,
+ .bandwidth_update = &rv515_bandwidth_update,
};
#endif
(le16_to_cpu(path->usConnObjectId) &
OBJECT_TYPE_MASK) >> OBJECT_TYPE_SHIFT;
- if ((le16_to_cpu(path->usDeviceTag) ==
- ATOM_DEVICE_TV1_SUPPORT)
- || (le16_to_cpu(path->usDeviceTag) ==
- ATOM_DEVICE_TV2_SUPPORT)
- || (le16_to_cpu(path->usDeviceTag) ==
- ATOM_DEVICE_CV_SUPPORT))
+ /* TODO CV support */
+ if (le16_to_cpu(path->usDeviceTag) ==
+ ATOM_DEVICE_CV_SUPPORT)
continue;
if ((rdev->family == CHIP_RS780) &&
#include "drmP.h"
#include "drm_edid.h"
#include "drm_crtc_helper.h"
+#include "drm_fb_helper.h"
#include "radeon_drm.h"
#include "radeon.h"
#include "atom.h"
if (common_modes[i].w < 320 || common_modes[i].h < 200)
continue;
- mode = drm_cvt_mode(dev, common_modes[i].w, common_modes[i].h, 60, false, false);
+ mode = drm_cvt_mode(dev, common_modes[i].w, common_modes[i].h, 60, false, false, false);
drm_mode_probed_add(connector, mode);
}
}
radeon_add_common_modes(encoder, connector);
else {
/* only 800x600 is supported right now on pre-avivo chips */
- tv_mode = drm_cvt_mode(dev, 800, 600, 60, false, false);
+ tv_mode = drm_cvt_mode(dev, 800, 600, 60, false, false, false);
tv_mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
drm_mode_probed_add(connector, tv_mode);
}
return NULL;
}
+static void radeon_dvi_force(struct drm_connector *connector)
+{
+ struct radeon_connector *radeon_connector = to_radeon_connector(connector);
+ if (connector->force == DRM_FORCE_ON)
+ radeon_connector->use_digital = false;
+ if (connector->force == DRM_FORCE_ON_DIGITAL)
+ radeon_connector->use_digital = true;
+}
+
struct drm_connector_helper_funcs radeon_dvi_connector_helper_funcs = {
.get_modes = radeon_dvi_get_modes,
.mode_valid = radeon_vga_mode_valid,
.fill_modes = drm_helper_probe_single_connector_modes,
.set_property = radeon_connector_set_property,
.destroy = radeon_connector_destroy,
+ .force = radeon_dvi_force,
};
void
struct radeon_connector *radeon_connector;
struct radeon_connector_atom_dig *radeon_dig_connector;
uint32_t subpixel_order = SubPixelNone;
+ int ret;
/* fixme - tv/cv/din */
if (connector_type == DRM_MODE_CONNECTOR_Unknown)
switch (connector_type) {
case DRM_MODE_CONNECTOR_VGA:
drm_connector_init(dev, &radeon_connector->base, &radeon_vga_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "VGA");
if (!radeon_connector->ddc_bus)
goto failed;
}
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
break;
case DRM_MODE_CONNECTOR_DVIA:
drm_connector_init(dev, &radeon_connector->base, &radeon_vga_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "DVI");
if (!radeon_connector->ddc_bus)
goto failed;
}
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
radeon_dig_connector->igp_lane_info = igp_lane_info;
radeon_connector->con_priv = radeon_dig_connector;
drm_connector_init(dev, &radeon_connector->base, &radeon_dvi_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "DVI");
if (!radeon_connector->ddc_bus)
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.coherent_mode_property,
1);
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
radeon_dig_connector->igp_lane_info = igp_lane_info;
radeon_connector->con_priv = radeon_dig_connector;
drm_connector_init(dev, &radeon_connector->base, &radeon_dvi_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "HDMI");
if (!radeon_connector->ddc_bus)
radeon_dig_connector->igp_lane_info = igp_lane_info;
radeon_connector->con_priv = radeon_dig_connector;
drm_connector_init(dev, &radeon_connector->base, &radeon_dvi_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "DP");
if (!radeon_connector->ddc_bus)
case DRM_MODE_CONNECTOR_9PinDIN:
if (radeon_tv == 1) {
drm_connector_init(dev, &radeon_connector->base, &radeon_tv_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_tv_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_tv_connector_helper_funcs);
+ if (ret)
+ goto failed;
+ radeon_connector->dac_load_detect = true;
+ drm_connector_attach_property(&radeon_connector->base,
+ rdev->mode_info.load_detect_property,
+ 1);
}
- drm_connector_attach_property(&radeon_connector->base,
- rdev->mode_info.load_detect_property,
- 1);
break;
case DRM_MODE_CONNECTOR_LVDS:
radeon_dig_connector = kzalloc(sizeof(struct radeon_connector_atom_dig), GFP_KERNEL);
radeon_dig_connector->igp_lane_info = igp_lane_info;
radeon_connector->con_priv = radeon_dig_connector;
drm_connector_init(dev, &radeon_connector->base, &radeon_lvds_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_lvds_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_lvds_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "LVDS");
if (!radeon_connector->ddc_bus)
struct drm_connector *connector;
struct radeon_connector *radeon_connector;
uint32_t subpixel_order = SubPixelNone;
+ int ret;
/* fixme - tv/cv/din */
if (connector_type == DRM_MODE_CONNECTOR_Unknown)
switch (connector_type) {
case DRM_MODE_CONNECTOR_VGA:
drm_connector_init(dev, &radeon_connector->base, &radeon_vga_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "VGA");
if (!radeon_connector->ddc_bus)
goto failed;
}
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
break;
case DRM_MODE_CONNECTOR_DVIA:
drm_connector_init(dev, &radeon_connector->base, &radeon_vga_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_vga_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "DVI");
if (!radeon_connector->ddc_bus)
goto failed;
}
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
case DRM_MODE_CONNECTOR_DVII:
case DRM_MODE_CONNECTOR_DVID:
drm_connector_init(dev, &radeon_connector->base, &radeon_dvi_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_dvi_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "DVI");
if (!radeon_connector->ddc_bus)
goto failed;
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
case DRM_MODE_CONNECTOR_9PinDIN:
if (radeon_tv == 1) {
drm_connector_init(dev, &radeon_connector->base, &radeon_tv_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_tv_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_tv_connector_helper_funcs);
+ if (ret)
+ goto failed;
+ radeon_connector->dac_load_detect = true;
drm_connector_attach_property(&radeon_connector->base,
rdev->mode_info.load_detect_property,
1);
break;
case DRM_MODE_CONNECTOR_LVDS:
drm_connector_init(dev, &radeon_connector->base, &radeon_lvds_connector_funcs, connector_type);
- drm_connector_helper_add(&radeon_connector->base, &radeon_lvds_connector_helper_funcs);
+ ret = drm_connector_helper_add(&radeon_connector->base, &radeon_lvds_connector_helper_funcs);
+ if (ret)
+ goto failed;
if (i2c_bus->valid) {
radeon_connector->ddc_bus = radeon_i2c_create(dev, i2c_bus, "LVDS");
if (!radeon_connector->ddc_bus)
}
p->chunks[i].length_dw = user_chunk.length_dw;
- cdata = (uint32_t *)(unsigned long)user_chunk.chunk_data;
+ p->chunks[i].user_ptr = (void __user *)(unsigned long)user_chunk.chunk_data;
- size = p->chunks[i].length_dw * sizeof(uint32_t);
- p->chunks[i].kdata = kmalloc(size, GFP_KERNEL);
- if (p->chunks[i].kdata == NULL) {
- return -ENOMEM;
- }
- if (DRM_COPY_FROM_USER(p->chunks[i].kdata, cdata, size)) {
- return -EFAULT;
+ cdata = (uint32_t *)(unsigned long)user_chunk.chunk_data;
+ if (p->chunks[i].chunk_id != RADEON_CHUNK_ID_IB) {
+ size = p->chunks[i].length_dw * sizeof(uint32_t);
+ p->chunks[i].kdata = kmalloc(size, GFP_KERNEL);
+ if (p->chunks[i].kdata == NULL) {
+ return -ENOMEM;
+ }
+ if (DRM_COPY_FROM_USER(p->chunks[i].kdata,
+ p->chunks[i].user_ptr, size)) {
+ return -EFAULT;
+ }
+ } else {
+ p->chunks[i].kpage[0] = kmalloc(PAGE_SIZE, GFP_KERNEL);
+ p->chunks[i].kpage[1] = kmalloc(PAGE_SIZE, GFP_KERNEL);
+ if (p->chunks[i].kpage[0] == NULL || p->chunks[i].kpage[1] == NULL) {
+ kfree(p->chunks[i].kpage[0]);
+ kfree(p->chunks[i].kpage[1]);
+ return -ENOMEM;
+ }
+ p->chunks[i].kpage_idx[0] = -1;
+ p->chunks[i].kpage_idx[1] = -1;
+ p->chunks[i].last_copied_page = -1;
+ p->chunks[i].last_page_index = ((p->chunks[i].length_dw * 4) - 1) / PAGE_SIZE;
}
}
if (p->chunks[p->chunk_ib_idx].length_dw > (16 * 1024)) {
kfree(parser->relocs_ptr);
for (i = 0; i < parser->nchunks; i++) {
kfree(parser->chunks[i].kdata);
+ kfree(parser->chunks[i].kpage[0]);
+ kfree(parser->chunks[i].kpage[1]);
}
kfree(parser->chunks);
kfree(parser->chunks_array);
* uncached). */
ib_chunk = &parser.chunks[parser.chunk_ib_idx];
parser.ib->length_dw = ib_chunk->length_dw;
- memcpy((void *)parser.ib->ptr, ib_chunk->kdata, ib_chunk->length_dw*4);
r = radeon_cs_parse(&parser);
+ if (r || parser.parser_error) {
+ DRM_ERROR("Invalid command stream !\n");
+ radeon_cs_parser_fini(&parser, r);
+ mutex_unlock(&rdev->cs_mutex);
+ return r;
+ }
+ r = radeon_cs_finish_pages(&parser);
if (r) {
DRM_ERROR("Invalid command stream !\n");
radeon_cs_parser_fini(&parser, r);
mutex_unlock(&rdev->cs_mutex);
return r;
}
+
+int radeon_cs_finish_pages(struct radeon_cs_parser *p)
+{
+ struct radeon_cs_chunk *ibc = &p->chunks[p->chunk_ib_idx];
+ int i;
+ int size = PAGE_SIZE;
+
+ for (i = ibc->last_copied_page + 1; i <= ibc->last_page_index; i++) {
+ if (i == ibc->last_page_index) {
+ size = (ibc->length_dw * 4) % PAGE_SIZE;
+ if (size == 0)
+ size = PAGE_SIZE;
+ }
+
+ if (DRM_COPY_FROM_USER(p->ib->ptr + (i * (PAGE_SIZE/4)),
+ ibc->user_ptr + (i * PAGE_SIZE),
+ size))
+ return -EFAULT;
+ }
+ return 0;
+}
+
+int radeon_cs_update_pages(struct radeon_cs_parser *p, int pg_idx)
+{
+ int new_page;
+ struct radeon_cs_chunk *ibc = &p->chunks[p->chunk_ib_idx];
+ int i;
+ int size = PAGE_SIZE;
+
+ for (i = ibc->last_copied_page + 1; i < pg_idx; i++) {
+ if (DRM_COPY_FROM_USER(p->ib->ptr + (i * (PAGE_SIZE/4)),
+ ibc->user_ptr + (i * PAGE_SIZE),
+ PAGE_SIZE)) {
+ p->parser_error = -EFAULT;
+ return 0;
+ }
+ }
+
+ new_page = ibc->kpage_idx[0] < ibc->kpage_idx[1] ? 0 : 1;
+
+ if (pg_idx == ibc->last_page_index) {
+ size = (ibc->length_dw * 4) % PAGE_SIZE;
+ if (size == 0)
+ size = PAGE_SIZE;
+ }
+
+ if (DRM_COPY_FROM_USER(ibc->kpage[new_page],
+ ibc->user_ptr + (pg_idx * PAGE_SIZE),
+ size)) {
+ p->parser_error = -EFAULT;
+ return 0;
+ }
+
+ /* copy to IB here */
+ memcpy((void *)(p->ib->ptr+(pg_idx*(PAGE_SIZE/4))), ibc->kpage[new_page], size);
+
+ ibc->last_copied_page = pg_idx;
+ ibc->kpage_idx[new_page] = pg_idx;
+
+ return new_page;
+}
if (radeon_agpmode == -1) {
rdev->flags &= ~RADEON_IS_AGP;
- if (rdev->family >= CHIP_RV515 ||
- rdev->family == CHIP_RV380 ||
- rdev->family == CHIP_RV410 ||
- rdev->family == CHIP_R423) {
+ if (rdev->family >= CHIP_R600) {
+ DRM_INFO("Forcing AGP to PCIE mode\n");
+ rdev->flags |= RADEON_IS_PCIE;
+ } else if (rdev->family >= CHIP_RV515 ||
+ rdev->family == CHIP_RV380 ||
+ rdev->family == CHIP_RV410 ||
+ rdev->family == CHIP_R423) {
DRM_INFO("Forcing AGP to PCIE mode\n");
rdev->flags |= RADEON_IS_PCIE;
rdev->asic->gart_init = &rv370_pcie_gart_init;
int radeon_driver_irq_postinstall_kms(struct drm_device *dev);
void radeon_driver_irq_uninstall_kms(struct drm_device *dev);
irqreturn_t radeon_driver_irq_handler_kms(DRM_IRQ_ARGS);
-int radeon_master_create_kms(struct drm_device *dev, struct drm_master *master);
-void radeon_master_destroy_kms(struct drm_device *dev,
- struct drm_master *master);
int radeon_dma_ioctl_kms(struct drm_device *dev, void *data,
struct drm_file *file_priv);
int radeon_gem_object_init(struct drm_gem_object *obj);
.get_vblank_counter = radeon_get_vblank_counter_kms,
.enable_vblank = radeon_enable_vblank_kms,
.disable_vblank = radeon_disable_vblank_kms,
- .master_create = radeon_master_create_kms,
- .master_destroy = radeon_master_destroy_kms,
#if defined(CONFIG_DEBUG_FS)
.debugfs_init = radeon_debugfs_init,
.debugfs_cleanup = radeon_debugfs_cleanup,
int radeonfb_create(struct drm_device *dev,
uint32_t fb_width, uint32_t fb_height,
uint32_t surface_width, uint32_t surface_height,
+ uint32_t surface_depth, uint32_t surface_bpp,
struct drm_framebuffer **fb_p)
{
struct radeon_device *rdev = dev->dev_private;
mode_cmd.width = surface_width;
mode_cmd.height = surface_height;
- mode_cmd.bpp = 32;
+ mode_cmd.bpp = surface_bpp;
/* need to align pitch with crtc limits */
mode_cmd.pitch = radeon_align_pitch(rdev, mode_cmd.width, mode_cmd.bpp, fb_tiled) * ((mode_cmd.bpp + 1) / 8);
- mode_cmd.depth = 24;
+ mode_cmd.depth = surface_depth;
size = mode_cmd.pitch * mode_cmd.height;
aligned_size = ALIGN(size, PAGE_SIZE);
return ret;
}
+static char *mode_option;
+int radeon_parse_options(char *options)
+{
+ char *this_opt;
+
+ if (!options || !*options)
+ return 0;
+
+ while ((this_opt = strsep(&options, ",")) != NULL) {
+ if (!*this_opt)
+ continue;
+ mode_option = this_opt;
+ }
+ return 0;
+}
+
int radeonfb_probe(struct drm_device *dev)
{
- int ret;
- ret = drm_fb_helper_single_fb_probe(dev, &radeonfb_create);
- return ret;
+ return drm_fb_helper_single_fb_probe(dev, &radeonfb_create);
}
-EXPORT_SYMBOL(radeonfb_probe);
int radeonfb_remove(struct drm_device *dev, struct drm_framebuffer *fb)
{
}
-/*
- * For multiple master (like multiple X).
- */
-struct drm_radeon_master_private {
- drm_local_map_t *sarea;
- drm_radeon_sarea_t *sarea_priv;
-};
-
-int radeon_master_create_kms(struct drm_device *dev, struct drm_master *master)
-{
- struct drm_radeon_master_private *master_priv;
- unsigned long sareapage;
- int ret;
-
- master_priv = kzalloc(sizeof(*master_priv), GFP_KERNEL);
- if (master_priv == NULL) {
- return -ENOMEM;
- }
- /* prebuild the SAREA */
- sareapage = max_t(unsigned long, SAREA_MAX, PAGE_SIZE);
- ret = drm_addmap(dev, 0, sareapage, _DRM_SHM,
- _DRM_CONTAINS_LOCK,
- &master_priv->sarea);
- if (ret) {
- DRM_ERROR("SAREA setup failed\n");
- return ret;
- }
- master_priv->sarea_priv = master_priv->sarea->handle + sizeof(struct drm_sarea);
- master_priv->sarea_priv->pfCurrentPage = 0;
- master->driver_priv = master_priv;
- return 0;
-}
-
-void radeon_master_destroy_kms(struct drm_device *dev,
- struct drm_master *master)
-{
- struct drm_radeon_master_private *master_priv = master->driver_priv;
-
- if (master_priv == NULL) {
- return;
- }
- if (master_priv->sarea) {
- drm_rmmap_locked(dev, master_priv->sarea);
- }
- kfree(master_priv);
- master->driver_priv = NULL;
-}
-
-
/*
* IOCTL.
*/
# define RADEON_CP_PACKET_MAX_DWORDS (1 << 12)
# define RADEON_CP_PACKET0_REG_MASK 0x000007ff
# define R300_CP_PACKET0_REG_MASK 0x00001fff
+# define R600_CP_PACKET0_REG_MASK 0x0000ffff
# define RADEON_CP_PACKET1_REG0_MASK 0x000007ff
# define RADEON_CP_PACKET1_REG1_MASK 0x003ff800
}
static struct vm_operations_struct radeon_ttm_vm_ops;
-static struct vm_operations_struct *ttm_vm_ops = NULL;
+static const struct vm_operations_struct *ttm_vm_ops = NULL;
static int radeon_ttm_fault(struct vm_area_struct *vma, struct vm_fault *vmf)
{
#define RADEON_DEBUGFS_MEM_TYPES 2
-static struct drm_info_list radeon_mem_types_list[RADEON_DEBUGFS_MEM_TYPES];
-static char radeon_mem_types_names[RADEON_DEBUGFS_MEM_TYPES][32];
-
#if defined(CONFIG_DEBUG_FS)
static int radeon_mm_dump_table(struct seq_file *m, void *data)
{
static int radeon_ttm_debugfs_init(struct radeon_device *rdev)
{
+#if defined(CONFIG_DEBUG_FS)
+ static struct drm_info_list radeon_mem_types_list[RADEON_DEBUGFS_MEM_TYPES];
+ static char radeon_mem_types_names[RADEON_DEBUGFS_MEM_TYPES][32];
unsigned i;
-#if defined(CONFIG_DEBUG_FS)
for (i = 0; i < RADEON_DEBUGFS_MEM_TYPES; i++) {
if (i == 0)
sprintf(radeon_mem_types_names[i], "radeon_vram_mm");
#include "drmP.h"
#include "radeon_reg.h"
#include "radeon.h"
-#include "avivod.h"
#include "rs600_reg_safe.h"
*/
void rs600_gpu_init(struct radeon_device *rdev);
int rs600_mc_wait_for_idle(struct radeon_device *rdev);
-void rs600_disable_vga(struct radeon_device *rdev);
/*
"programming pipes. Bad things might happen.\n");
}
- radeon_avivo_vga_render_disable(rdev);
+ rv515_vga_render_disable(rdev);
tmp = RREG32(AVIVO_D1VGA_CONTROL);
WREG32(AVIVO_D1VGA_CONTROL, tmp & ~AVIVO_DVGA_CONTROL_MODE_ENABLE);
/*
* Global GPU functions
*/
-void rs600_disable_vga(struct radeon_device *rdev)
-{
- unsigned tmp;
-
- WREG32(0x330, 0);
- WREG32(0x338, 0);
- tmp = RREG32(0x300);
- tmp &= ~(3 << 16);
- WREG32(0x300, tmp);
- WREG32(0x308, (1 << 8));
- WREG32(0x310, rdev->mc.vram_location);
- WREG32(0x594, 0);
-}
-
int rs600_mc_wait_for_idle(struct radeon_device *rdev)
{
unsigned i;
{
/* FIXME: HDP same place on rs600 ? */
r100_hdp_reset(rdev);
- rs600_disable_vga(rdev);
+ rv515_vga_render_disable(rdev);
/* FIXME: is this correct ? */
r420_pipes_init(rdev);
if (rs600_mc_wait_for_idle(rdev)) {
int rs400_gart_enable(struct radeon_device *rdev);
void rs400_gart_adjust_size(struct radeon_device *rdev);
void rs600_mc_disable_clients(struct radeon_device *rdev);
-void rs600_disable_vga(struct radeon_device *rdev);
/* This files gather functions specifics to :
* rs690,rs740
{
/* FIXME: HDP same place on rs690 ? */
r100_hdp_reset(rdev);
- rs600_disable_vga(rdev);
+ rv515_vga_render_disable(rdev);
/* FIXME: is this correct ? */
r420_pipes_init(rdev);
if (rs690_mc_wait_for_idle(rdev)) {
#include "drmP.h"
#include "rv515d.h"
#include "radeon.h"
-
+#include "atom.h"
#include "rv515_reg_safe.h"
-/* rv515 depends on : */
-void r100_hdp_reset(struct radeon_device *rdev);
-int r100_cp_reset(struct radeon_device *rdev);
-int r100_rb2d_reset(struct radeon_device *rdev);
-int r100_gui_wait_for_idle(struct radeon_device *rdev);
-int r100_cp_init(struct radeon_device *rdev, unsigned ring_size);
-void r420_pipes_init(struct radeon_device *rdev);
-void rs600_mc_disable_clients(struct radeon_device *rdev);
-void rs600_disable_vga(struct radeon_device *rdev);
-
-/* This files gather functions specifics to:
- * rv515
- *
- * Some of these functions might be used by newer ASICs.
- */
+
+/* This files gather functions specifics to: rv515 */
int rv515_debugfs_pipes_info_init(struct radeon_device *rdev);
int rv515_debugfs_ga_info_init(struct radeon_device *rdev);
void rv515_gpu_init(struct radeon_device *rdev);
int rv515_mc_wait_for_idle(struct radeon_device *rdev);
-
-/*
- * MC
- */
-int rv515_mc_init(struct radeon_device *rdev)
+void rv515_debugfs(struct radeon_device *rdev)
{
- uint32_t tmp;
- int r;
-
if (r100_debugfs_rbbm_init(rdev)) {
DRM_ERROR("Failed to register debugfs file for RBBM !\n");
}
if (rv515_debugfs_ga_info_init(rdev)) {
DRM_ERROR("Failed to register debugfs file for pipes !\n");
}
-
- rv515_gpu_init(rdev);
- rv370_pcie_gart_disable(rdev);
-
- /* Setup GPU memory space */
- rdev->mc.vram_location = 0xFFFFFFFFUL;
- rdev->mc.gtt_location = 0xFFFFFFFFUL;
- if (rdev->flags & RADEON_IS_AGP) {
- r = radeon_agp_init(rdev);
- if (r) {
- printk(KERN_WARNING "[drm] Disabling AGP\n");
- rdev->flags &= ~RADEON_IS_AGP;
- rdev->mc.gtt_size = radeon_gart_size * 1024 * 1024;
- } else {
- rdev->mc.gtt_location = rdev->mc.agp_base;
- }
- }
- r = radeon_mc_setup(rdev);
- if (r) {
- return r;
- }
-
- /* Program GPU memory space */
- rs600_mc_disable_clients(rdev);
- if (rv515_mc_wait_for_idle(rdev)) {
- printk(KERN_WARNING "Failed to wait MC idle while "
- "programming pipes. Bad things might happen.\n");
- }
- /* Write VRAM size in case we are limiting it */
- WREG32(RADEON_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
- tmp = REG_SET(MC_FB_START, rdev->mc.vram_location >> 16);
- WREG32(0x134, tmp);
- tmp = rdev->mc.vram_location + rdev->mc.mc_vram_size - 1;
- tmp = REG_SET(MC_FB_TOP, tmp >> 16);
- tmp |= REG_SET(MC_FB_START, rdev->mc.vram_location >> 16);
- WREG32_MC(MC_FB_LOCATION, tmp);
- WREG32(HDP_FB_LOCATION, rdev->mc.vram_location >> 16);
- WREG32(0x310, rdev->mc.vram_location);
- if (rdev->flags & RADEON_IS_AGP) {
- tmp = rdev->mc.gtt_location + rdev->mc.gtt_size - 1;
- tmp = REG_SET(MC_AGP_TOP, tmp >> 16);
- tmp |= REG_SET(MC_AGP_START, rdev->mc.gtt_location >> 16);
- WREG32_MC(MC_AGP_LOCATION, tmp);
- WREG32_MC(MC_AGP_BASE, rdev->mc.agp_base);
- WREG32_MC(MC_AGP_BASE_2, 0);
- } else {
- WREG32_MC(MC_AGP_LOCATION, 0x0FFFFFFF);
- WREG32_MC(MC_AGP_BASE, 0);
- WREG32_MC(MC_AGP_BASE_2, 0);
- }
- return 0;
-}
-
-void rv515_mc_fini(struct radeon_device *rdev)
-{
}
-
-/*
- * Global GPU functions
- */
void rv515_ring_start(struct radeon_device *rdev)
{
int r;
radeon_ring_unlock_commit(rdev);
}
-void rv515_errata(struct radeon_device *rdev)
-{
- rdev->pll_errata = 0;
-}
-
int rv515_mc_wait_for_idle(struct radeon_device *rdev)
{
unsigned i;
return -1;
}
+void rv515_vga_render_disable(struct radeon_device *rdev)
+{
+ WREG32(R_000300_VGA_RENDER_CONTROL,
+ RREG32(R_000300_VGA_RENDER_CONTROL) & C_000300_VGA_VSTATUS_CNTL);
+}
+
void rv515_gpu_init(struct radeon_device *rdev)
{
unsigned pipe_select_current, gb_pipe_select, tmp;
"reseting GPU. Bad things might happen.\n");
}
- rs600_disable_vga(rdev);
+ rv515_vga_render_disable(rdev);
r420_pipes_init(rdev);
gb_pipe_select = RREG32(0x402C);
return 0;
}
-
-/*
- * VRAM info
- */
static void rv515_vram_get_type(struct radeon_device *rdev)
{
uint32_t tmp;
rdev->pm.sclk.full = rfixed_div(rdev->pm.sclk, a);
}
-
-/*
- * Indirect registers accessor
- */
uint32_t rv515_mc_rreg(struct radeon_device *rdev, uint32_t reg)
{
uint32_t r;
WREG32(MC_IND_INDEX, 0);
}
-/*
- * Debugfs info
- */
#if defined(CONFIG_DEBUG_FS)
static int rv515_debugfs_pipes_info(struct seq_file *m, void *data)
{
#endif
}
-/*
- * Asic initialization
- */
-int rv515_init(struct radeon_device *rdev)
+void rv515_mc_stop(struct radeon_device *rdev, struct rv515_mc_save *save)
+{
+ save->d1vga_control = RREG32(R_000330_D1VGA_CONTROL);
+ save->d2vga_control = RREG32(R_000338_D2VGA_CONTROL);
+ save->vga_render_control = RREG32(R_000300_VGA_RENDER_CONTROL);
+ save->vga_hdp_control = RREG32(R_000328_VGA_HDP_CONTROL);
+ save->d1crtc_control = RREG32(R_006080_D1CRTC_CONTROL);
+ save->d2crtc_control = RREG32(R_006880_D2CRTC_CONTROL);
+
+ /* Stop all video */
+ WREG32(R_000330_D1VGA_CONTROL, 0);
+ WREG32(R_0068E8_D2CRTC_UPDATE_LOCK, 0);
+ WREG32(R_000300_VGA_RENDER_CONTROL, 0);
+ WREG32(R_0060E8_D1CRTC_UPDATE_LOCK, 1);
+ WREG32(R_0068E8_D2CRTC_UPDATE_LOCK, 1);
+ WREG32(R_006080_D1CRTC_CONTROL, 0);
+ WREG32(R_006880_D2CRTC_CONTROL, 0);
+ WREG32(R_0060E8_D1CRTC_UPDATE_LOCK, 0);
+ WREG32(R_0068E8_D2CRTC_UPDATE_LOCK, 0);
+}
+
+void rv515_mc_resume(struct radeon_device *rdev, struct rv515_mc_save *save)
+{
+ WREG32(R_006110_D1GRPH_PRIMARY_SURFACE_ADDRESS, rdev->mc.vram_start);
+ WREG32(R_006118_D1GRPH_SECONDARY_SURFACE_ADDRESS, rdev->mc.vram_start);
+ WREG32(R_006910_D2GRPH_PRIMARY_SURFACE_ADDRESS, rdev->mc.vram_start);
+ WREG32(R_006918_D2GRPH_SECONDARY_SURFACE_ADDRESS, rdev->mc.vram_start);
+ WREG32(R_000310_VGA_MEMORY_BASE_ADDRESS, rdev->mc.vram_start);
+ /* Unlock host access */
+ WREG32(R_000328_VGA_HDP_CONTROL, save->vga_hdp_control);
+ mdelay(1);
+ /* Restore video state */
+ WREG32(R_0060E8_D1CRTC_UPDATE_LOCK, 1);
+ WREG32(R_0068E8_D2CRTC_UPDATE_LOCK, 1);
+ WREG32(R_006080_D1CRTC_CONTROL, save->d1crtc_control);
+ WREG32(R_006880_D2CRTC_CONTROL, save->d2crtc_control);
+ WREG32(R_0060E8_D1CRTC_UPDATE_LOCK, 0);
+ WREG32(R_0068E8_D2CRTC_UPDATE_LOCK, 0);
+ WREG32(R_000330_D1VGA_CONTROL, save->d1vga_control);
+ WREG32(R_000338_D2VGA_CONTROL, save->d2vga_control);
+ WREG32(R_000300_VGA_RENDER_CONTROL, save->vga_render_control);
+}
+
+void rv515_mc_program(struct radeon_device *rdev)
+{
+ struct rv515_mc_save save;
+
+ /* Stops all mc clients */
+ rv515_mc_stop(rdev, &save);
+
+ /* Wait for mc idle */
+ if (rv515_mc_wait_for_idle(rdev))
+ dev_warn(rdev->dev, "Wait MC idle timeout before updating MC.\n");
+ /* Write VRAM size in case we are limiting it */
+ WREG32(R_0000F8_CONFIG_MEMSIZE, rdev->mc.real_vram_size);
+ /* Program MC, should be a 32bits limited address space */
+ WREG32_MC(R_000001_MC_FB_LOCATION,
+ S_000001_MC_FB_START(rdev->mc.vram_start >> 16) |
+ S_000001_MC_FB_TOP(rdev->mc.vram_end >> 16));
+ WREG32(R_000134_HDP_FB_LOCATION,
+ S_000134_HDP_FB_START(rdev->mc.vram_start >> 16));
+ if (rdev->flags & RADEON_IS_AGP) {
+ WREG32_MC(R_000002_MC_AGP_LOCATION,
+ S_000002_MC_AGP_START(rdev->mc.gtt_start >> 16) |
+ S_000002_MC_AGP_TOP(rdev->mc.gtt_end >> 16));
+ WREG32_MC(R_000003_MC_AGP_BASE, lower_32_bits(rdev->mc.agp_base));
+ WREG32_MC(R_000004_MC_AGP_BASE_2,
+ S_000004_AGP_BASE_ADDR_2(upper_32_bits(rdev->mc.agp_base)));
+ } else {
+ WREG32_MC(R_000002_MC_AGP_LOCATION, 0xFFFFFFFF);
+ WREG32_MC(R_000003_MC_AGP_BASE, 0);
+ WREG32_MC(R_000004_MC_AGP_BASE_2, 0);
+ }
+
+ rv515_mc_resume(rdev, &save);
+}
+
+void rv515_clock_startup(struct radeon_device *rdev)
+{
+ if (radeon_dynclks != -1 && radeon_dynclks)
+ radeon_atom_set_clock_gating(rdev, 1);
+ /* We need to force on some of the block */
+ WREG32_PLL(R_00000F_CP_DYN_CNTL,
+ RREG32_PLL(R_00000F_CP_DYN_CNTL) | S_00000F_CP_FORCEON(1));
+ WREG32_PLL(R_000011_E2_DYN_CNTL,
+ RREG32_PLL(R_000011_E2_DYN_CNTL) | S_000011_E2_FORCEON(1));
+ WREG32_PLL(R_000013_IDCT_DYN_CNTL,
+ RREG32_PLL(R_000013_IDCT_DYN_CNTL) | S_000013_IDCT_FORCEON(1));
+}
+
+static int rv515_startup(struct radeon_device *rdev)
+{
+ int r;
+
+ rv515_mc_program(rdev);
+ /* Resume clock */
+ rv515_clock_startup(rdev);
+ /* Initialize GPU configuration (# pipes, ...) */
+ rv515_gpu_init(rdev);
+ /* Initialize GART (initialize after TTM so we can allocate
+ * memory through TTM but finalize after TTM) */
+ if (rdev->flags & RADEON_IS_PCIE) {
+ r = rv370_pcie_gart_enable(rdev);
+ if (r)
+ return r;
+ }
+ /* Enable IRQ */
+ rdev->irq.sw_int = true;
+ r100_irq_set(rdev);
+ /* 1M ring buffer */
+ r = r100_cp_init(rdev, 1024 * 1024);
+ if (r) {
+ dev_err(rdev->dev, "failled initializing CP (%d).\n", r);
+ return r;
+ }
+ r = r100_wb_init(rdev);
+ if (r)
+ dev_err(rdev->dev, "failled initializing WB (%d).\n", r);
+ r = r100_ib_init(rdev);
+ if (r) {
+ dev_err(rdev->dev, "failled initializing IB (%d).\n", r);
+ return r;
+ }
+ return 0;
+}
+
+int rv515_resume(struct radeon_device *rdev)
+{
+ /* Make sur GART are not working */
+ if (rdev->flags & RADEON_IS_PCIE)
+ rv370_pcie_gart_disable(rdev);
+ /* Resume clock before doing reset */
+ rv515_clock_startup(rdev);
+ /* Reset gpu before posting otherwise ATOM will enter infinite loop */
+ if (radeon_gpu_reset(rdev)) {
+ dev_warn(rdev->dev, "GPU reset failed ! (0xE40=0x%08X, 0x7C0=0x%08X)\n",
+ RREG32(R_000E40_RBBM_STATUS),
+ RREG32(R_0007C0_CP_STAT));
+ }
+ /* post */
+ atom_asic_init(rdev->mode_info.atom_context);
+ /* Resume clock after posting */
+ rv515_clock_startup(rdev);
+ return rv515_startup(rdev);
+}
+
+int rv515_suspend(struct radeon_device *rdev)
+{
+ r100_cp_disable(rdev);
+ r100_wb_disable(rdev);
+ r100_irq_disable(rdev);
+ if (rdev->flags & RADEON_IS_PCIE)
+ rv370_pcie_gart_disable(rdev);
+ return 0;
+}
+
+void rv515_set_safe_registers(struct radeon_device *rdev)
{
rdev->config.r300.reg_safe_bm = rv515_reg_safe_bm;
rdev->config.r300.reg_safe_bm_size = ARRAY_SIZE(rv515_reg_safe_bm);
+}
+
+void rv515_fini(struct radeon_device *rdev)
+{
+ rv515_suspend(rdev);
+ r100_cp_fini(rdev);
+ r100_wb_fini(rdev);
+ r100_ib_fini(rdev);
+ radeon_gem_fini(rdev);
+ rv370_pcie_gart_fini(rdev);
+ radeon_agp_fini(rdev);
+ radeon_irq_kms_fini(rdev);
+ radeon_fence_driver_fini(rdev);
+ radeon_object_fini(rdev);
+ radeon_atombios_fini(rdev);
+ kfree(rdev->bios);
+ rdev->bios = NULL;
+}
+
+int rv515_init(struct radeon_device *rdev)
+{
+ int r;
+
+ rdev->new_init_path = true;
+ /* Initialize scratch registers */
+ radeon_scratch_init(rdev);
+ /* Initialize surface registers */
+ radeon_surface_init(rdev);
+ /* TODO: disable VGA need to use VGA request */
+ /* BIOS*/
+ if (!radeon_get_bios(rdev)) {
+ if (ASIC_IS_AVIVO(rdev))
+ return -EINVAL;
+ }
+ if (rdev->is_atom_bios) {
+ r = radeon_atombios_init(rdev);
+ if (r)
+ return r;
+ } else {
+ dev_err(rdev->dev, "Expecting atombios for RV515 GPU\n");
+ return -EINVAL;
+ }
+ /* Reset gpu before posting otherwise ATOM will enter infinite loop */
+ if (radeon_gpu_reset(rdev)) {
+ dev_warn(rdev->dev,
+ "GPU reset failed ! (0xE40=0x%08X, 0x7C0=0x%08X)\n",
+ RREG32(R_000E40_RBBM_STATUS),
+ RREG32(R_0007C0_CP_STAT));
+ }
+ /* check if cards are posted or not */
+ if (!radeon_card_posted(rdev) && rdev->bios) {
+ DRM_INFO("GPU not posted. posting now...\n");
+ atom_asic_init(rdev->mode_info.atom_context);
+ }
+ /* Initialize clocks */
+ radeon_get_clock_info(rdev->ddev);
+ /* Get vram informations */
+ rv515_vram_info(rdev);
+ /* Initialize memory controller (also test AGP) */
+ r = r420_mc_init(rdev);
+ if (r)
+ return r;
+ rv515_debugfs(rdev);
+ /* Fence driver */
+ r = radeon_fence_driver_init(rdev);
+ if (r)
+ return r;
+ r = radeon_irq_kms_init(rdev);
+ if (r)
+ return r;
+ /* Memory manager */
+ r = radeon_object_init(rdev);
+ if (r)
+ return r;
+ r = rv370_pcie_gart_init(rdev);
+ if (r)
+ return r;
+ rv515_set_safe_registers(rdev);
+ rdev->accel_working = true;
+ r = rv515_startup(rdev);
+ if (r) {
+ /* Somethings want wront with the accel init stop accel */
+ dev_err(rdev->dev, "Disabling GPU acceleration\n");
+ rv515_suspend(rdev);
+ r100_cp_fini(rdev);
+ r100_wb_fini(rdev);
+ r100_ib_fini(rdev);
+ rv370_pcie_gart_fini(rdev);
+ radeon_agp_fini(rdev);
+ radeon_irq_kms_fini(rdev);
+ rdev->accel_working = false;
+ }
return 0;
}
#define CP_PACKET0_GET_ONE_REG_WR(h) (((h) >> 15) & 1)
#define CP_PACKET3_GET_OPCODE(h) (((h) >> 8) & 0xFF)
-#endif
+/* Registers */
+#define R_0000F8_CONFIG_MEMSIZE 0x0000F8
+#define S_0000F8_CONFIG_MEMSIZE(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_0000F8_CONFIG_MEMSIZE(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_0000F8_CONFIG_MEMSIZE 0x00000000
+#define R_000134_HDP_FB_LOCATION 0x000134
+#define S_000134_HDP_FB_START(x) (((x) & 0xFFFF) << 0)
+#define G_000134_HDP_FB_START(x) (((x) >> 0) & 0xFFFF)
+#define C_000134_HDP_FB_START 0xFFFF0000
+#define R_000300_VGA_RENDER_CONTROL 0x000300
+#define S_000300_VGA_BLINK_RATE(x) (((x) & 0x1F) << 0)
+#define G_000300_VGA_BLINK_RATE(x) (((x) >> 0) & 0x1F)
+#define C_000300_VGA_BLINK_RATE 0xFFFFFFE0
+#define S_000300_VGA_BLINK_MODE(x) (((x) & 0x3) << 5)
+#define G_000300_VGA_BLINK_MODE(x) (((x) >> 5) & 0x3)
+#define C_000300_VGA_BLINK_MODE 0xFFFFFF9F
+#define S_000300_VGA_CURSOR_BLINK_INVERT(x) (((x) & 0x1) << 7)
+#define G_000300_VGA_CURSOR_BLINK_INVERT(x) (((x) >> 7) & 0x1)
+#define C_000300_VGA_CURSOR_BLINK_INVERT 0xFFFFFF7F
+#define S_000300_VGA_EXTD_ADDR_COUNT_ENABLE(x) (((x) & 0x1) << 8)
+#define G_000300_VGA_EXTD_ADDR_COUNT_ENABLE(x) (((x) >> 8) & 0x1)
+#define C_000300_VGA_EXTD_ADDR_COUNT_ENABLE 0xFFFFFEFF
+#define S_000300_VGA_VSTATUS_CNTL(x) (((x) & 0x3) << 16)
+#define G_000300_VGA_VSTATUS_CNTL(x) (((x) >> 16) & 0x3)
+#define C_000300_VGA_VSTATUS_CNTL 0xFFFCFFFF
+#define S_000300_VGA_LOCK_8DOT(x) (((x) & 0x1) << 24)
+#define G_000300_VGA_LOCK_8DOT(x) (((x) >> 24) & 0x1)
+#define C_000300_VGA_LOCK_8DOT 0xFEFFFFFF
+#define S_000300_VGAREG_LINECMP_COMPATIBILITY_SEL(x) (((x) & 0x1) << 25)
+#define G_000300_VGAREG_LINECMP_COMPATIBILITY_SEL(x) (((x) >> 25) & 0x1)
+#define C_000300_VGAREG_LINECMP_COMPATIBILITY_SEL 0xFDFFFFFF
+#define R_000310_VGA_MEMORY_BASE_ADDRESS 0x000310
+#define S_000310_VGA_MEMORY_BASE_ADDRESS(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_000310_VGA_MEMORY_BASE_ADDRESS(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_000310_VGA_MEMORY_BASE_ADDRESS 0x00000000
+#define R_000328_VGA_HDP_CONTROL 0x000328
+#define S_000328_VGA_MEM_PAGE_SELECT_EN(x) (((x) & 0x1) << 0)
+#define G_000328_VGA_MEM_PAGE_SELECT_EN(x) (((x) >> 0) & 0x1)
+#define C_000328_VGA_MEM_PAGE_SELECT_EN 0xFFFFFFFE
+#define S_000328_VGA_RBBM_LOCK_DISABLE(x) (((x) & 0x1) << 8)
+#define G_000328_VGA_RBBM_LOCK_DISABLE(x) (((x) >> 8) & 0x1)
+#define C_000328_VGA_RBBM_LOCK_DISABLE 0xFFFFFEFF
+#define S_000328_VGA_SOFT_RESET(x) (((x) & 0x1) << 16)
+#define G_000328_VGA_SOFT_RESET(x) (((x) >> 16) & 0x1)
+#define C_000328_VGA_SOFT_RESET 0xFFFEFFFF
+#define S_000328_VGA_TEST_RESET_CONTROL(x) (((x) & 0x1) << 24)
+#define G_000328_VGA_TEST_RESET_CONTROL(x) (((x) >> 24) & 0x1)
+#define C_000328_VGA_TEST_RESET_CONTROL 0xFEFFFFFF
+#define R_000330_D1VGA_CONTROL 0x000330
+#define S_000330_D1VGA_MODE_ENABLE(x) (((x) & 0x1) << 0)
+#define G_000330_D1VGA_MODE_ENABLE(x) (((x) >> 0) & 0x1)
+#define C_000330_D1VGA_MODE_ENABLE 0xFFFFFFFE
+#define S_000330_D1VGA_TIMING_SELECT(x) (((x) & 0x1) << 8)
+#define G_000330_D1VGA_TIMING_SELECT(x) (((x) >> 8) & 0x1)
+#define C_000330_D1VGA_TIMING_SELECT 0xFFFFFEFF
+#define S_000330_D1VGA_SYNC_POLARITY_SELECT(x) (((x) & 0x1) << 9)
+#define G_000330_D1VGA_SYNC_POLARITY_SELECT(x) (((x) >> 9) & 0x1)
+#define C_000330_D1VGA_SYNC_POLARITY_SELECT 0xFFFFFDFF
+#define S_000330_D1VGA_OVERSCAN_TIMING_SELECT(x) (((x) & 0x1) << 10)
+#define G_000330_D1VGA_OVERSCAN_TIMING_SELECT(x) (((x) >> 10) & 0x1)
+#define C_000330_D1VGA_OVERSCAN_TIMING_SELECT 0xFFFFFBFF
+#define S_000330_D1VGA_OVERSCAN_COLOR_EN(x) (((x) & 0x1) << 16)
+#define G_000330_D1VGA_OVERSCAN_COLOR_EN(x) (((x) >> 16) & 0x1)
+#define C_000330_D1VGA_OVERSCAN_COLOR_EN 0xFFFEFFFF
+#define S_000330_D1VGA_ROTATE(x) (((x) & 0x3) << 24)
+#define G_000330_D1VGA_ROTATE(x) (((x) >> 24) & 0x3)
+#define C_000330_D1VGA_ROTATE 0xFCFFFFFF
+#define R_000338_D2VGA_CONTROL 0x000338
+#define S_000338_D2VGA_MODE_ENABLE(x) (((x) & 0x1) << 0)
+#define G_000338_D2VGA_MODE_ENABLE(x) (((x) >> 0) & 0x1)
+#define C_000338_D2VGA_MODE_ENABLE 0xFFFFFFFE
+#define S_000338_D2VGA_TIMING_SELECT(x) (((x) & 0x1) << 8)
+#define G_000338_D2VGA_TIMING_SELECT(x) (((x) >> 8) & 0x1)
+#define C_000338_D2VGA_TIMING_SELECT 0xFFFFFEFF
+#define S_000338_D2VGA_SYNC_POLARITY_SELECT(x) (((x) & 0x1) << 9)
+#define G_000338_D2VGA_SYNC_POLARITY_SELECT(x) (((x) >> 9) & 0x1)
+#define C_000338_D2VGA_SYNC_POLARITY_SELECT 0xFFFFFDFF
+#define S_000338_D2VGA_OVERSCAN_TIMING_SELECT(x) (((x) & 0x1) << 10)
+#define G_000338_D2VGA_OVERSCAN_TIMING_SELECT(x) (((x) >> 10) & 0x1)
+#define C_000338_D2VGA_OVERSCAN_TIMING_SELECT 0xFFFFFBFF
+#define S_000338_D2VGA_OVERSCAN_COLOR_EN(x) (((x) & 0x1) << 16)
+#define G_000338_D2VGA_OVERSCAN_COLOR_EN(x) (((x) >> 16) & 0x1)
+#define C_000338_D2VGA_OVERSCAN_COLOR_EN 0xFFFEFFFF
+#define S_000338_D2VGA_ROTATE(x) (((x) & 0x3) << 24)
+#define G_000338_D2VGA_ROTATE(x) (((x) >> 24) & 0x3)
+#define C_000338_D2VGA_ROTATE 0xFCFFFFFF
+#define R_0007C0_CP_STAT 0x0007C0
+#define S_0007C0_MRU_BUSY(x) (((x) & 0x1) << 0)
+#define G_0007C0_MRU_BUSY(x) (((x) >> 0) & 0x1)
+#define C_0007C0_MRU_BUSY 0xFFFFFFFE
+#define S_0007C0_MWU_BUSY(x) (((x) & 0x1) << 1)
+#define G_0007C0_MWU_BUSY(x) (((x) >> 1) & 0x1)
+#define C_0007C0_MWU_BUSY 0xFFFFFFFD
+#define S_0007C0_RSIU_BUSY(x) (((x) & 0x1) << 2)
+#define G_0007C0_RSIU_BUSY(x) (((x) >> 2) & 0x1)
+#define C_0007C0_RSIU_BUSY 0xFFFFFFFB
+#define S_0007C0_RCIU_BUSY(x) (((x) & 0x1) << 3)
+#define G_0007C0_RCIU_BUSY(x) (((x) >> 3) & 0x1)
+#define C_0007C0_RCIU_BUSY 0xFFFFFFF7
+#define S_0007C0_CSF_PRIMARY_BUSY(x) (((x) & 0x1) << 9)
+#define G_0007C0_CSF_PRIMARY_BUSY(x) (((x) >> 9) & 0x1)
+#define C_0007C0_CSF_PRIMARY_BUSY 0xFFFFFDFF
+#define S_0007C0_CSF_INDIRECT_BUSY(x) (((x) & 0x1) << 10)
+#define G_0007C0_CSF_INDIRECT_BUSY(x) (((x) >> 10) & 0x1)
+#define C_0007C0_CSF_INDIRECT_BUSY 0xFFFFFBFF
+#define S_0007C0_CSQ_PRIMARY_BUSY(x) (((x) & 0x1) << 11)
+#define G_0007C0_CSQ_PRIMARY_BUSY(x) (((x) >> 11) & 0x1)
+#define C_0007C0_CSQ_PRIMARY_BUSY 0xFFFFF7FF
+#define S_0007C0_CSQ_INDIRECT_BUSY(x) (((x) & 0x1) << 12)
+#define G_0007C0_CSQ_INDIRECT_BUSY(x) (((x) >> 12) & 0x1)
+#define C_0007C0_CSQ_INDIRECT_BUSY 0xFFFFEFFF
+#define S_0007C0_CSI_BUSY(x) (((x) & 0x1) << 13)
+#define G_0007C0_CSI_BUSY(x) (((x) >> 13) & 0x1)
+#define C_0007C0_CSI_BUSY 0xFFFFDFFF
+#define S_0007C0_CSF_INDIRECT2_BUSY(x) (((x) & 0x1) << 14)
+#define G_0007C0_CSF_INDIRECT2_BUSY(x) (((x) >> 14) & 0x1)
+#define C_0007C0_CSF_INDIRECT2_BUSY 0xFFFFBFFF
+#define S_0007C0_CSQ_INDIRECT2_BUSY(x) (((x) & 0x1) << 15)
+#define G_0007C0_CSQ_INDIRECT2_BUSY(x) (((x) >> 15) & 0x1)
+#define C_0007C0_CSQ_INDIRECT2_BUSY 0xFFFF7FFF
+#define S_0007C0_GUIDMA_BUSY(x) (((x) & 0x1) << 28)
+#define G_0007C0_GUIDMA_BUSY(x) (((x) >> 28) & 0x1)
+#define C_0007C0_GUIDMA_BUSY 0xEFFFFFFF
+#define S_0007C0_VIDDMA_BUSY(x) (((x) & 0x1) << 29)
+#define G_0007C0_VIDDMA_BUSY(x) (((x) >> 29) & 0x1)
+#define C_0007C0_VIDDMA_BUSY 0xDFFFFFFF
+#define S_0007C0_CMDSTRM_BUSY(x) (((x) & 0x1) << 30)
+#define G_0007C0_CMDSTRM_BUSY(x) (((x) >> 30) & 0x1)
+#define C_0007C0_CMDSTRM_BUSY 0xBFFFFFFF
+#define S_0007C0_CP_BUSY(x) (((x) & 0x1) << 31)
+#define G_0007C0_CP_BUSY(x) (((x) >> 31) & 0x1)
+#define C_0007C0_CP_BUSY 0x7FFFFFFF
+#define R_000E40_RBBM_STATUS 0x000E40
+#define S_000E40_CMDFIFO_AVAIL(x) (((x) & 0x7F) << 0)
+#define G_000E40_CMDFIFO_AVAIL(x) (((x) >> 0) & 0x7F)
+#define C_000E40_CMDFIFO_AVAIL 0xFFFFFF80
+#define S_000E40_HIRQ_ON_RBB(x) (((x) & 0x1) << 8)
+#define G_000E40_HIRQ_ON_RBB(x) (((x) >> 8) & 0x1)
+#define C_000E40_HIRQ_ON_RBB 0xFFFFFEFF
+#define S_000E40_CPRQ_ON_RBB(x) (((x) & 0x1) << 9)
+#define G_000E40_CPRQ_ON_RBB(x) (((x) >> 9) & 0x1)
+#define C_000E40_CPRQ_ON_RBB 0xFFFFFDFF
+#define S_000E40_CFRQ_ON_RBB(x) (((x) & 0x1) << 10)
+#define G_000E40_CFRQ_ON_RBB(x) (((x) >> 10) & 0x1)
+#define C_000E40_CFRQ_ON_RBB 0xFFFFFBFF
+#define S_000E40_HIRQ_IN_RTBUF(x) (((x) & 0x1) << 11)
+#define G_000E40_HIRQ_IN_RTBUF(x) (((x) >> 11) & 0x1)
+#define C_000E40_HIRQ_IN_RTBUF 0xFFFFF7FF
+#define S_000E40_CPRQ_IN_RTBUF(x) (((x) & 0x1) << 12)
+#define G_000E40_CPRQ_IN_RTBUF(x) (((x) >> 12) & 0x1)
+#define C_000E40_CPRQ_IN_RTBUF 0xFFFFEFFF
+#define S_000E40_CFRQ_IN_RTBUF(x) (((x) & 0x1) << 13)
+#define G_000E40_CFRQ_IN_RTBUF(x) (((x) >> 13) & 0x1)
+#define C_000E40_CFRQ_IN_RTBUF 0xFFFFDFFF
+#define S_000E40_CF_PIPE_BUSY(x) (((x) & 0x1) << 14)
+#define G_000E40_CF_PIPE_BUSY(x) (((x) >> 14) & 0x1)
+#define C_000E40_CF_PIPE_BUSY 0xFFFFBFFF
+#define S_000E40_ENG_EV_BUSY(x) (((x) & 0x1) << 15)
+#define G_000E40_ENG_EV_BUSY(x) (((x) >> 15) & 0x1)
+#define C_000E40_ENG_EV_BUSY 0xFFFF7FFF
+#define S_000E40_CP_CMDSTRM_BUSY(x) (((x) & 0x1) << 16)
+#define G_000E40_CP_CMDSTRM_BUSY(x) (((x) >> 16) & 0x1)
+#define C_000E40_CP_CMDSTRM_BUSY 0xFFFEFFFF
+#define S_000E40_E2_BUSY(x) (((x) & 0x1) << 17)
+#define G_000E40_E2_BUSY(x) (((x) >> 17) & 0x1)
+#define C_000E40_E2_BUSY 0xFFFDFFFF
+#define S_000E40_RB2D_BUSY(x) (((x) & 0x1) << 18)
+#define G_000E40_RB2D_BUSY(x) (((x) >> 18) & 0x1)
+#define C_000E40_RB2D_BUSY 0xFFFBFFFF
+#define S_000E40_RB3D_BUSY(x) (((x) & 0x1) << 19)
+#define G_000E40_RB3D_BUSY(x) (((x) >> 19) & 0x1)
+#define C_000E40_RB3D_BUSY 0xFFF7FFFF
+#define S_000E40_VAP_BUSY(x) (((x) & 0x1) << 20)
+#define G_000E40_VAP_BUSY(x) (((x) >> 20) & 0x1)
+#define C_000E40_VAP_BUSY 0xFFEFFFFF
+#define S_000E40_RE_BUSY(x) (((x) & 0x1) << 21)
+#define G_000E40_RE_BUSY(x) (((x) >> 21) & 0x1)
+#define C_000E40_RE_BUSY 0xFFDFFFFF
+#define S_000E40_TAM_BUSY(x) (((x) & 0x1) << 22)
+#define G_000E40_TAM_BUSY(x) (((x) >> 22) & 0x1)
+#define C_000E40_TAM_BUSY 0xFFBFFFFF
+#define S_000E40_TDM_BUSY(x) (((x) & 0x1) << 23)
+#define G_000E40_TDM_BUSY(x) (((x) >> 23) & 0x1)
+#define C_000E40_TDM_BUSY 0xFF7FFFFF
+#define S_000E40_PB_BUSY(x) (((x) & 0x1) << 24)
+#define G_000E40_PB_BUSY(x) (((x) >> 24) & 0x1)
+#define C_000E40_PB_BUSY 0xFEFFFFFF
+#define S_000E40_TIM_BUSY(x) (((x) & 0x1) << 25)
+#define G_000E40_TIM_BUSY(x) (((x) >> 25) & 0x1)
+#define C_000E40_TIM_BUSY 0xFDFFFFFF
+#define S_000E40_GA_BUSY(x) (((x) & 0x1) << 26)
+#define G_000E40_GA_BUSY(x) (((x) >> 26) & 0x1)
+#define C_000E40_GA_BUSY 0xFBFFFFFF
+#define S_000E40_CBA2D_BUSY(x) (((x) & 0x1) << 27)
+#define G_000E40_CBA2D_BUSY(x) (((x) >> 27) & 0x1)
+#define C_000E40_CBA2D_BUSY 0xF7FFFFFF
+#define S_000E40_RBBM_HIBUSY(x) (((x) & 0x1) << 28)
+#define G_000E40_RBBM_HIBUSY(x) (((x) >> 28) & 0x1)
+#define C_000E40_RBBM_HIBUSY 0xEFFFFFFF
+#define S_000E40_SKID_CFBUSY(x) (((x) & 0x1) << 29)
+#define G_000E40_SKID_CFBUSY(x) (((x) >> 29) & 0x1)
+#define C_000E40_SKID_CFBUSY 0xDFFFFFFF
+#define S_000E40_VAP_VF_BUSY(x) (((x) & 0x1) << 30)
+#define G_000E40_VAP_VF_BUSY(x) (((x) >> 30) & 0x1)
+#define C_000E40_VAP_VF_BUSY 0xBFFFFFFF
+#define S_000E40_GUI_ACTIVE(x) (((x) & 0x1) << 31)
+#define G_000E40_GUI_ACTIVE(x) (((x) >> 31) & 0x1)
+#define C_000E40_GUI_ACTIVE 0x7FFFFFFF
+#define R_006080_D1CRTC_CONTROL 0x006080
+#define S_006080_D1CRTC_MASTER_EN(x) (((x) & 0x1) << 0)
+#define G_006080_D1CRTC_MASTER_EN(x) (((x) >> 0) & 0x1)
+#define C_006080_D1CRTC_MASTER_EN 0xFFFFFFFE
+#define S_006080_D1CRTC_SYNC_RESET_SEL(x) (((x) & 0x1) << 4)
+#define G_006080_D1CRTC_SYNC_RESET_SEL(x) (((x) >> 4) & 0x1)
+#define C_006080_D1CRTC_SYNC_RESET_SEL 0xFFFFFFEF
+#define S_006080_D1CRTC_DISABLE_POINT_CNTL(x) (((x) & 0x3) << 8)
+#define G_006080_D1CRTC_DISABLE_POINT_CNTL(x) (((x) >> 8) & 0x3)
+#define C_006080_D1CRTC_DISABLE_POINT_CNTL 0xFFFFFCFF
+#define S_006080_D1CRTC_CURRENT_MASTER_EN_STATE(x) (((x) & 0x1) << 16)
+#define G_006080_D1CRTC_CURRENT_MASTER_EN_STATE(x) (((x) >> 16) & 0x1)
+#define C_006080_D1CRTC_CURRENT_MASTER_EN_STATE 0xFFFEFFFF
+#define S_006080_D1CRTC_DISP_READ_REQUEST_DISABLE(x) (((x) & 0x1) << 24)
+#define G_006080_D1CRTC_DISP_READ_REQUEST_DISABLE(x) (((x) >> 24) & 0x1)
+#define C_006080_D1CRTC_DISP_READ_REQUEST_DISABLE 0xFEFFFFFF
+#define R_0060E8_D1CRTC_UPDATE_LOCK 0x0060E8
+#define S_0060E8_D1CRTC_UPDATE_LOCK(x) (((x) & 0x1) << 0)
+#define G_0060E8_D1CRTC_UPDATE_LOCK(x) (((x) >> 0) & 0x1)
+#define C_0060E8_D1CRTC_UPDATE_LOCK 0xFFFFFFFE
+#define R_006110_D1GRPH_PRIMARY_SURFACE_ADDRESS 0x006110
+#define S_006110_D1GRPH_PRIMARY_SURFACE_ADDRESS(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_006110_D1GRPH_PRIMARY_SURFACE_ADDRESS(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_006110_D1GRPH_PRIMARY_SURFACE_ADDRESS 0x00000000
+#define R_006118_D1GRPH_SECONDARY_SURFACE_ADDRESS 0x006118
+#define S_006118_D1GRPH_SECONDARY_SURFACE_ADDRESS(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_006118_D1GRPH_SECONDARY_SURFACE_ADDRESS(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_006118_D1GRPH_SECONDARY_SURFACE_ADDRESS 0x00000000
+#define R_006880_D2CRTC_CONTROL 0x006880
+#define S_006880_D2CRTC_MASTER_EN(x) (((x) & 0x1) << 0)
+#define G_006880_D2CRTC_MASTER_EN(x) (((x) >> 0) & 0x1)
+#define C_006880_D2CRTC_MASTER_EN 0xFFFFFFFE
+#define S_006880_D2CRTC_SYNC_RESET_SEL(x) (((x) & 0x1) << 4)
+#define G_006880_D2CRTC_SYNC_RESET_SEL(x) (((x) >> 4) & 0x1)
+#define C_006880_D2CRTC_SYNC_RESET_SEL 0xFFFFFFEF
+#define S_006880_D2CRTC_DISABLE_POINT_CNTL(x) (((x) & 0x3) << 8)
+#define G_006880_D2CRTC_DISABLE_POINT_CNTL(x) (((x) >> 8) & 0x3)
+#define C_006880_D2CRTC_DISABLE_POINT_CNTL 0xFFFFFCFF
+#define S_006880_D2CRTC_CURRENT_MASTER_EN_STATE(x) (((x) & 0x1) << 16)
+#define G_006880_D2CRTC_CURRENT_MASTER_EN_STATE(x) (((x) >> 16) & 0x1)
+#define C_006880_D2CRTC_CURRENT_MASTER_EN_STATE 0xFFFEFFFF
+#define S_006880_D2CRTC_DISP_READ_REQUEST_DISABLE(x) (((x) & 0x1) << 24)
+#define G_006880_D2CRTC_DISP_READ_REQUEST_DISABLE(x) (((x) >> 24) & 0x1)
+#define C_006880_D2CRTC_DISP_READ_REQUEST_DISABLE 0xFEFFFFFF
+#define R_0068E8_D2CRTC_UPDATE_LOCK 0x0068E8
+#define S_0068E8_D2CRTC_UPDATE_LOCK(x) (((x) & 0x1) << 0)
+#define G_0068E8_D2CRTC_UPDATE_LOCK(x) (((x) >> 0) & 0x1)
+#define C_0068E8_D2CRTC_UPDATE_LOCK 0xFFFFFFFE
+#define R_006910_D2GRPH_PRIMARY_SURFACE_ADDRESS 0x006910
+#define S_006910_D2GRPH_PRIMARY_SURFACE_ADDRESS(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_006910_D2GRPH_PRIMARY_SURFACE_ADDRESS(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_006910_D2GRPH_PRIMARY_SURFACE_ADDRESS 0x00000000
+#define R_006918_D2GRPH_SECONDARY_SURFACE_ADDRESS 0x006918
+#define S_006918_D2GRPH_SECONDARY_SURFACE_ADDRESS(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_006918_D2GRPH_SECONDARY_SURFACE_ADDRESS(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_006918_D2GRPH_SECONDARY_SURFACE_ADDRESS 0x00000000
+
+
+#define R_000001_MC_FB_LOCATION 0x000001
+#define S_000001_MC_FB_START(x) (((x) & 0xFFFF) << 0)
+#define G_000001_MC_FB_START(x) (((x) >> 0) & 0xFFFF)
+#define C_000001_MC_FB_START 0xFFFF0000
+#define S_000001_MC_FB_TOP(x) (((x) & 0xFFFF) << 16)
+#define G_000001_MC_FB_TOP(x) (((x) >> 16) & 0xFFFF)
+#define C_000001_MC_FB_TOP 0x0000FFFF
+#define R_000002_MC_AGP_LOCATION 0x000002
+#define S_000002_MC_AGP_START(x) (((x) & 0xFFFF) << 0)
+#define G_000002_MC_AGP_START(x) (((x) >> 0) & 0xFFFF)
+#define C_000002_MC_AGP_START 0xFFFF0000
+#define S_000002_MC_AGP_TOP(x) (((x) & 0xFFFF) << 16)
+#define G_000002_MC_AGP_TOP(x) (((x) >> 16) & 0xFFFF)
+#define C_000002_MC_AGP_TOP 0x0000FFFF
+#define R_000003_MC_AGP_BASE 0x000003
+#define S_000003_AGP_BASE_ADDR(x) (((x) & 0xFFFFFFFF) << 0)
+#define G_000003_AGP_BASE_ADDR(x) (((x) >> 0) & 0xFFFFFFFF)
+#define C_000003_AGP_BASE_ADDR 0x00000000
+#define R_000004_MC_AGP_BASE_2 0x000004
+#define S_000004_AGP_BASE_ADDR_2(x) (((x) & 0xF) << 0)
+#define G_000004_AGP_BASE_ADDR_2(x) (((x) >> 0) & 0xF)
+#define C_000004_AGP_BASE_ADDR_2 0xFFFFFFF0
+
+#define R_00000F_CP_DYN_CNTL 0x00000F
+#define S_00000F_CP_FORCEON(x) (((x) & 0x1) << 0)
+#define G_00000F_CP_FORCEON(x) (((x) >> 0) & 0x1)
+#define C_00000F_CP_FORCEON 0xFFFFFFFE
+#define S_00000F_CP_MAX_DYN_STOP_LAT(x) (((x) & 0x1) << 1)
+#define G_00000F_CP_MAX_DYN_STOP_LAT(x) (((x) >> 1) & 0x1)
+#define C_00000F_CP_MAX_DYN_STOP_LAT 0xFFFFFFFD
+#define S_00000F_CP_CLOCK_STATUS(x) (((x) & 0x1) << 2)
+#define G_00000F_CP_CLOCK_STATUS(x) (((x) >> 2) & 0x1)
+#define C_00000F_CP_CLOCK_STATUS 0xFFFFFFFB
+#define S_00000F_CP_PROG_SHUTOFF(x) (((x) & 0x1) << 3)
+#define G_00000F_CP_PROG_SHUTOFF(x) (((x) >> 3) & 0x1)
+#define C_00000F_CP_PROG_SHUTOFF 0xFFFFFFF7
+#define S_00000F_CP_PROG_DELAY_VALUE(x) (((x) & 0xFF) << 4)
+#define G_00000F_CP_PROG_DELAY_VALUE(x) (((x) >> 4) & 0xFF)
+#define C_00000F_CP_PROG_DELAY_VALUE 0xFFFFF00F
+#define S_00000F_CP_LOWER_POWER_IDLE(x) (((x) & 0xFF) << 12)
+#define G_00000F_CP_LOWER_POWER_IDLE(x) (((x) >> 12) & 0xFF)
+#define C_00000F_CP_LOWER_POWER_IDLE 0xFFF00FFF
+#define S_00000F_CP_LOWER_POWER_IGNORE(x) (((x) & 0x1) << 20)
+#define G_00000F_CP_LOWER_POWER_IGNORE(x) (((x) >> 20) & 0x1)
+#define C_00000F_CP_LOWER_POWER_IGNORE 0xFFEFFFFF
+#define S_00000F_CP_NORMAL_POWER_IGNORE(x) (((x) & 0x1) << 21)
+#define G_00000F_CP_NORMAL_POWER_IGNORE(x) (((x) >> 21) & 0x1)
+#define C_00000F_CP_NORMAL_POWER_IGNORE 0xFFDFFFFF
+#define S_00000F_SPARE(x) (((x) & 0x3) << 22)
+#define G_00000F_SPARE(x) (((x) >> 22) & 0x3)
+#define C_00000F_SPARE 0xFF3FFFFF
+#define S_00000F_CP_NORMAL_POWER_BUSY(x) (((x) & 0xFF) << 24)
+#define G_00000F_CP_NORMAL_POWER_BUSY(x) (((x) >> 24) & 0xFF)
+#define C_00000F_CP_NORMAL_POWER_BUSY 0x00FFFFFF
+#define R_000011_E2_DYN_CNTL 0x000011
+#define S_000011_E2_FORCEON(x) (((x) & 0x1) << 0)
+#define G_000011_E2_FORCEON(x) (((x) >> 0) & 0x1)
+#define C_000011_E2_FORCEON 0xFFFFFFFE
+#define S_000011_E2_MAX_DYN_STOP_LAT(x) (((x) & 0x1) << 1)
+#define G_000011_E2_MAX_DYN_STOP_LAT(x) (((x) >> 1) & 0x1)
+#define C_000011_E2_MAX_DYN_STOP_LAT 0xFFFFFFFD
+#define S_000011_E2_CLOCK_STATUS(x) (((x) & 0x1) << 2)
+#define G_000011_E2_CLOCK_STATUS(x) (((x) >> 2) & 0x1)
+#define C_000011_E2_CLOCK_STATUS 0xFFFFFFFB
+#define S_000011_E2_PROG_SHUTOFF(x) (((x) & 0x1) << 3)
+#define G_000011_E2_PROG_SHUTOFF(x) (((x) >> 3) & 0x1)
+#define C_000011_E2_PROG_SHUTOFF 0xFFFFFFF7
+#define S_000011_E2_PROG_DELAY_VALUE(x) (((x) & 0xFF) << 4)
+#define G_000011_E2_PROG_DELAY_VALUE(x) (((x) >> 4) & 0xFF)
+#define C_000011_E2_PROG_DELAY_VALUE 0xFFFFF00F
+#define S_000011_E2_LOWER_POWER_IDLE(x) (((x) & 0xFF) << 12)
+#define G_000011_E2_LOWER_POWER_IDLE(x) (((x) >> 12) & 0xFF)
+#define C_000011_E2_LOWER_POWER_IDLE 0xFFF00FFF
+#define S_000011_E2_LOWER_POWER_IGNORE(x) (((x) & 0x1) << 20)
+#define G_000011_E2_LOWER_POWER_IGNORE(x) (((x) >> 20) & 0x1)
+#define C_000011_E2_LOWER_POWER_IGNORE 0xFFEFFFFF
+#define S_000011_E2_NORMAL_POWER_IGNORE(x) (((x) & 0x1) << 21)
+#define G_000011_E2_NORMAL_POWER_IGNORE(x) (((x) >> 21) & 0x1)
+#define C_000011_E2_NORMAL_POWER_IGNORE 0xFFDFFFFF
+#define S_000011_SPARE(x) (((x) & 0x3) << 22)
+#define G_000011_SPARE(x) (((x) >> 22) & 0x3)
+#define C_000011_SPARE 0xFF3FFFFF
+#define S_000011_E2_NORMAL_POWER_BUSY(x) (((x) & 0xFF) << 24)
+#define G_000011_E2_NORMAL_POWER_BUSY(x) (((x) >> 24) & 0xFF)
+#define C_000011_E2_NORMAL_POWER_BUSY 0x00FFFFFF
+#define R_000013_IDCT_DYN_CNTL 0x000013
+#define S_000013_IDCT_FORCEON(x) (((x) & 0x1) << 0)
+#define G_000013_IDCT_FORCEON(x) (((x) >> 0) & 0x1)
+#define C_000013_IDCT_FORCEON 0xFFFFFFFE
+#define S_000013_IDCT_MAX_DYN_STOP_LAT(x) (((x) & 0x1) << 1)
+#define G_000013_IDCT_MAX_DYN_STOP_LAT(x) (((x) >> 1) & 0x1)
+#define C_000013_IDCT_MAX_DYN_STOP_LAT 0xFFFFFFFD
+#define S_000013_IDCT_CLOCK_STATUS(x) (((x) & 0x1) << 2)
+#define G_000013_IDCT_CLOCK_STATUS(x) (((x) >> 2) & 0x1)
+#define C_000013_IDCT_CLOCK_STATUS 0xFFFFFFFB
+#define S_000013_IDCT_PROG_SHUTOFF(x) (((x) & 0x1) << 3)
+#define G_000013_IDCT_PROG_SHUTOFF(x) (((x) >> 3) & 0x1)
+#define C_000013_IDCT_PROG_SHUTOFF 0xFFFFFFF7
+#define S_000013_IDCT_PROG_DELAY_VALUE(x) (((x) & 0xFF) << 4)
+#define G_000013_IDCT_PROG_DELAY_VALUE(x) (((x) >> 4) & 0xFF)
+#define C_000013_IDCT_PROG_DELAY_VALUE 0xFFFFF00F
+#define S_000013_IDCT_LOWER_POWER_IDLE(x) (((x) & 0xFF) << 12)
+#define G_000013_IDCT_LOWER_POWER_IDLE(x) (((x) >> 12) & 0xFF)
+#define C_000013_IDCT_LOWER_POWER_IDLE 0xFFF00FFF
+#define S_000013_IDCT_LOWER_POWER_IGNORE(x) (((x) & 0x1) << 20)
+#define G_000013_IDCT_LOWER_POWER_IGNORE(x) (((x) >> 20) & 0x1)
+#define C_000013_IDCT_LOWER_POWER_IGNORE 0xFFEFFFFF
+#define S_000013_IDCT_NORMAL_POWER_IGNORE(x) (((x) & 0x1) << 21)
+#define G_000013_IDCT_NORMAL_POWER_IGNORE(x) (((x) >> 21) & 0x1)
+#define C_000013_IDCT_NORMAL_POWER_IGNORE 0xFFDFFFFF
+#define S_000013_SPARE(x) (((x) & 0x3) << 22)
+#define G_000013_SPARE(x) (((x) >> 22) & 0x3)
+#define C_000013_SPARE 0xFF3FFFFF
+#define S_000013_IDCT_NORMAL_POWER_BUSY(x) (((x) & 0xFF) << 24)
+#define G_000013_IDCT_NORMAL_POWER_BUSY(x) (((x) >> 24) & 0xFF)
+#define C_000013_IDCT_NORMAL_POWER_BUSY 0x00FFFFFF
+
+#endif
#include "radeon.h"
#include "radeon_drm.h"
#include "rv770d.h"
-#include "avivod.h"
#include "atom.h"
+#include "avivod.h"
#define R700_PFP_UCODE_SIZE 848
#define R700_PM4_UCODE_SIZE 1360
/* we need to own VRAM, so turn off the VGA renderer here
* to stop it overwriting our objects */
- radeon_avivo_vga_render_disable(rdev);
+ rv515_vga_render_disable(rdev);
}
/* Setup GPU memory space */
rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE);
rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE);
+
+ if (rdev->mc.mc_vram_size > rdev->mc.aper_size)
+ rdev->mc.mc_vram_size = rdev->mc.aper_size;
+
+ if (rdev->mc.real_vram_size > rdev->mc.aper_size)
+ rdev->mc.real_vram_size = rdev->mc.aper_size;
+
if (rdev->flags & RADEON_IS_AGP) {
r = radeon_agp_init(rdev);
if (r)
vma->vm_private_data = NULL;
}
-static struct vm_operations_struct ttm_bo_vm_ops = {
+static const struct vm_operations_struct ttm_bo_vm_ops = {
.fault = ttm_bo_vm_fault,
.open = ttm_bo_vm_open,
.close = ttm_bo_vm_close
#include <linux/major.h>
#include <linux/hid.h>
#include <linux/mutex.h>
+#include <linux/sched.h>
#include <linux/smp_lock.h>
#include <linux/hidraw.h>
return ret;
}
-static struct file_operations watchdog_fops = {
+static const struct file_operations watchdog_fops = {
.owner = THIS_MODULE,
.llseek = no_llseek,
.open = watchdog_open,
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
-static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/* Insmod parameters */
-I2C_CLIENT_INSMOD_1(ltc4215);
-
/* Here are names of the chip's registers (a.k.a. commands) */
enum ltc4215_cmd {
LTC4215_CONTROL = 0x00, /* rw */
static int ltc4215_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
+ struct i2c_adapter *adapter = client->adapter;
struct ltc4215_data *data;
int ret;
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ return -ENODEV;
+
data = kzalloc(sizeof(*data), GFP_KERNEL);
if (!data) {
ret = -ENOMEM;
return 0;
}
-static int ltc4215_detect(struct i2c_client *client,
- int kind,
- struct i2c_board_info *info)
-{
- struct i2c_adapter *adapter = client->adapter;
-
- if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
- return -ENODEV;
-
- if (kind < 0) { /* probed detection - check the chip type */
- s32 v; /* 8 bits from the chip, or -ERRNO */
-
- /*
- * Register 0x01 bit b7 is reserved, expect 0
- * Register 0x03 bit b6 and b7 are reserved, expect 0
- */
- v = i2c_smbus_read_byte_data(client, LTC4215_ALERT);
- if (v < 0 || (v & (1 << 7)) != 0)
- return -ENODEV;
-
- v = i2c_smbus_read_byte_data(client, LTC4215_FAULT);
- if (v < 0 || (v & ((1 << 6) | (1 << 7))) != 0)
- return -ENODEV;
- }
-
- strlcpy(info->type, "ltc4215", I2C_NAME_SIZE);
- dev_info(&adapter->dev, "ltc4215 %s at address 0x%02x\n",
- kind < 0 ? "probed" : "forced",
- client->addr);
-
- return 0;
-}
-
static const struct i2c_device_id ltc4215_id[] = {
- { "ltc4215", ltc4215 },
+ { "ltc4215", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ltc4215_id);
/* This is the driver that will be inserted */
static struct i2c_driver ltc4215_driver = {
- .class = I2C_CLASS_HWMON,
.driver = {
.name = "ltc4215",
},
.probe = ltc4215_probe,
.remove = ltc4215_remove,
.id_table = ltc4215_id,
- .detect = ltc4215_detect,
- .address_data = &addr_data,
};
static int __init ltc4215_init(void)
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
-/* Valid addresses are 0x20 - 0x3f
- *
- * For now, we do not probe, since some of these addresses
- * are known to be unfriendly to probing */
-static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/* Insmod parameters */
-I2C_CLIENT_INSMOD_1(ltc4245);
-
/* Here are names of the chip's registers (a.k.a. commands) */
enum ltc4245_cmd {
LTC4245_STATUS = 0x00, /* readonly */
static int ltc4245_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
+ struct i2c_adapter *adapter = client->adapter;
struct ltc4245_data *data;
int ret;
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ return -ENODEV;
+
data = kzalloc(sizeof(*data), GFP_KERNEL);
if (!data) {
ret = -ENOMEM;
return 0;
}
-/* Check that some bits in a control register appear at all possible
- * locations without changing value
- *
- * @client: the i2c client to use
- * @reg: the register to read
- * @bits: the bits to check (0xff checks all bits,
- * 0x03 checks only the last two bits)
- *
- * return -ERRNO if the register read failed
- * return -ENODEV if the register value doesn't stay constant at all
- * possible addresses
- *
- * return 0 for success
- */
-static int ltc4245_check_control_reg(struct i2c_client *client, u8 reg, u8 bits)
-{
- int i;
- s32 v, voff1, voff2;
-
- /* Read register and check for error */
- v = i2c_smbus_read_byte_data(client, reg);
- if (v < 0)
- return v;
-
- v &= bits;
-
- for (i = 0x00; i < 0xff; i += 0x20) {
-
- voff1 = i2c_smbus_read_byte_data(client, reg + i);
- if (voff1 < 0)
- return voff1;
-
- voff2 = i2c_smbus_read_byte_data(client, reg + i + 0x08);
- if (voff2 < 0)
- return voff2;
-
- voff1 &= bits;
- voff2 &= bits;
-
- if (v != voff1 || v != voff2)
- return -ENODEV;
- }
-
- return 0;
-}
-
-static int ltc4245_detect(struct i2c_client *client,
- int kind,
- struct i2c_board_info *info)
-{
- struct i2c_adapter *adapter = client->adapter;
-
- if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
- return -ENODEV;
-
- if (kind < 0) { /* probed detection - check the chip type */
- s32 v; /* 8 bits from the chip, or -ERRNO */
-
- /* Chip registers 0x00-0x07 are control registers
- * Chip registers 0x10-0x1f are data registers
- *
- * Address bits b7-b5 are ignored. This makes the chip "repeat"
- * in steps of 0x20. Any control registers should appear with
- * the same values across all duplicated addresses.
- *
- * Register 0x02 bit b2 is reserved, expect 0
- * Register 0x07 bits b7 to b4 are reserved, expect 0
- *
- * Registers 0x01, 0x02 are control registers and should not
- * change on their own.
- *
- * Register 0x06 bits b6 and b7 are control bits, and should
- * not change on their own.
- *
- * Register 0x07 bits b3 to b0 are control bits, and should
- * not change on their own.
- */
-
- /* read register 0x02 reserved bit, expect 0 */
- v = i2c_smbus_read_byte_data(client, LTC4245_CONTROL);
- if (v < 0 || (v & 0x04) != 0)
- return -ENODEV;
-
- /* read register 0x07 reserved bits, expect 0 */
- v = i2c_smbus_read_byte_data(client, LTC4245_ADCADR);
- if (v < 0 || (v & 0xf0) != 0)
- return -ENODEV;
-
- /* check that the alert register appears at all locations */
- if (ltc4245_check_control_reg(client, LTC4245_ALERT, 0xff))
- return -ENODEV;
-
- /* check that the control register appears at all locations */
- if (ltc4245_check_control_reg(client, LTC4245_CONTROL, 0xff))
- return -ENODEV;
-
- /* check that register 0x06 bits b6 and b7 stay constant */
- if (ltc4245_check_control_reg(client, LTC4245_GPIO, 0xc0))
- return -ENODEV;
-
- /* check that register 0x07 bits b3-b0 stay constant */
- if (ltc4245_check_control_reg(client, LTC4245_ADCADR, 0x0f))
- return -ENODEV;
- }
-
- strlcpy(info->type, "ltc4245", I2C_NAME_SIZE);
- dev_info(&adapter->dev, "ltc4245 %s at address 0x%02x\n",
- kind < 0 ? "probed" : "forced",
- client->addr);
-
- return 0;
-}
-
static const struct i2c_device_id ltc4245_id[] = {
- { "ltc4245", ltc4245 },
+ { "ltc4245", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ltc4245_id);
/* This is the driver that will be inserted */
static struct i2c_driver ltc4245_driver = {
- .class = I2C_CLASS_HWMON,
.driver = {
.name = "ltc4245",
},
.probe = ltc4245_probe,
.remove = ltc4245_remove,
.id_table = ltc4245_id,
- .detect = ltc4245_detect,
- .address_data = &addr_data,
};
static int __init ltc4245_init(void)
will be called i2c-pnx.
config I2C_PXA
- tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)"
- depends on EXPERIMENTAL && ARCH_PXA
+ tristate "Intel PXA2XX I2C adapter"
+ depends on ARCH_PXA || ARCH_MMP
help
If you have devices in the PXA I2C bus, say yes to this option.
This driver can also be built as a module. If so, the module
error = acpi_check_region(amd756_ioport, SMB_IOSIZE,
amd756_driver.name);
if (error)
- return error;
+ return -ENODEV;
if (!request_region(amd756_ioport, SMB_IOSIZE, amd756_driver.name)) {
dev_err(&pdev->dev, "SMB region 0x%x already in use!\n",
smbus->size = pci_resource_len(dev, 0);
error = acpi_check_resource_conflict(&dev->resource[0]);
- if (error)
+ if (error) {
+ error = -ENODEV;
goto out_kfree;
+ }
if (!request_region(smbus->base, smbus->size, amd8111_driver.name)) {
error = -EBUSY;
}
err = acpi_check_resource_conflict(&dev->resource[SMBBAR]);
- if (err)
+ if (err) {
+ err = -ENODEV;
goto exit;
+ }
err = pci_request_region(dev, SMBBAR, i801_driver.name);
if (err) {
return -ENODEV;
}
if (acpi_check_region(sch_smba, SMBIOSIZE, sch_driver.name))
- return -EBUSY;
+ return -ENODEV;
if (!request_region(sch_smba, SMBIOSIZE, sch_driver.name)) {
dev_err(&dev->dev, "SMBus region 0x%x already in use!\n",
sch_smba);
}
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
- return -EBUSY;
+ return -ENODEV;
if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
- return -EBUSY;
+ return -ENODEV;
if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
goto err;
snprintf(smbus_cmi->adapter.name, sizeof(smbus_cmi->adapter.name),
- "SMBus CMI adapter %s (%s)",
- acpi_device_name(device),
- acpi_device_uid(device));
+ "SMBus CMI adapter %s",
+ acpi_device_name(device));
smbus_cmi->adapter.owner = THIS_MODULE;
smbus_cmi->adapter.algo = &acpi_smbus_cmi_algorithm;
smbus_cmi->adapter.algo_data = smbus_cmi;
retval = acpi_check_resource_conflict(&dev->resource[SIS96x_BAR]);
if (retval)
- return retval;
+ return -ENODEV;
/* Everything is happy, let's grab the memory and set things up. */
if (!request_region(sis96x_smbus_base, SMB_IOSIZE,
found:
error = acpi_check_region(vt596_smba, 8, vt596_driver.name);
if (error)
- return error;
+ return -ENODEV;
if (!request_region(vt596_smba, 8, vt596_driver.name)) {
dev_err(&pdev->dev, "SMBus region 0x%x already in use!\n",
#include <asm/idle.h>
-#include "../dma/ioatdma_hw.h"
-#include "../dma/ioatdma_registers.h"
+#include "../dma/ioat/hw.h"
+#include "../dma/ioat/registers.h"
#define I7300_IDLE_DRIVER_VERSION "1.55"
#define I7300_PRINT "i7300_idle:"
udelay(10);
sts = readq(ioat_chanbase + IOAT1_CHANSTS_OFFSET) &
- IOAT_CHANSTS_DMA_TRANSFER_STATUS;
+ IOAT_CHANSTS_STATUS;
- if (sts != IOAT_CHANSTS_DMA_TRANSFER_STATUS_ACTIVE)
+ if (sts != IOAT_CHANSTS_ACTIVE)
break;
}
udelay(1000);
chan_sts = readq(ioat_chanbase + IOAT1_CHANSTS_OFFSET) &
- IOAT_CHANSTS_DMA_TRANSFER_STATUS;
+ IOAT_CHANSTS_STATUS;
- if (chan_sts != IOAT_CHANSTS_DMA_TRANSFER_STATUS_DONE) {
+ if (chan_sts != IOAT_CHANSTS_DONE) {
/* Not complete, reset the channel */
writeb(IOAT_CHANCMD_RESET,
ioat_chanbase + IOAT1_CHANCMD_OFFSET);
ioat_chanbase + IOAT1_CHANCMD_OFFSET);
chan_sts = readq(ioat_chanbase + IOAT1_CHANSTS_OFFSET) &
- IOAT_CHANSTS_DMA_TRANSFER_STATUS;
+ IOAT_CHANSTS_STATUS;
- if (chan_sts != IOAT_CHANSTS_DMA_TRANSFER_STATUS_ACTIVE) {
+ if (chan_sts != IOAT_CHANSTS_ACTIVE) {
writew(0, ioat_chanbase + IOAT_CHANCTRL_OFFSET);
break;
}
}
chan_sts = readq(ioat_chanbase + IOAT1_CHANSTS_OFFSET) &
- IOAT_CHANSTS_DMA_TRANSFER_STATUS;
+ IOAT_CHANSTS_STATUS;
/*
* We tried to reset multiple times. If IO A/T channel is still active
* flag an error and return without cleanup. Memory leak is better
* than random corruption in that extreme error situation.
*/
- if (chan_sts == IOAT_CHANSTS_DMA_TRANSFER_STATUS_ACTIVE) {
+ if (chan_sts == IOAT_CHANSTS_ACTIVE) {
printk(KERN_ERR I7300_PRINT "Unable to stop IO A/T channels."
" Not freeing resources\n");
return;
return 0;
}
-static struct vm_operations_struct dma_region_vm_ops = {
+static const struct vm_operations_struct dma_region_vm_ops = {
.fault = dma_region_pagefault,
};
enum rmpp_state {
RMPP_STATE_ACTIVE,
RMPP_STATE_TIMEOUT,
- RMPP_STATE_COMPLETE
+ RMPP_STATE_COMPLETE,
+ RMPP_STATE_CANCELING
};
struct mad_rmpp_recv {
unsigned long flags;
spin_lock_irqsave(&agent->lock, flags);
+ list_for_each_entry(rmpp_recv, &agent->rmpp_list, list) {
+ if (rmpp_recv->state != RMPP_STATE_COMPLETE)
+ ib_free_recv_mad(rmpp_recv->rmpp_wc);
+ rmpp_recv->state = RMPP_STATE_CANCELING;
+ }
+ spin_unlock_irqrestore(&agent->lock, flags);
+
list_for_each_entry(rmpp_recv, &agent->rmpp_list, list) {
cancel_delayed_work(&rmpp_recv->timeout_work);
cancel_delayed_work(&rmpp_recv->cleanup_work);
}
- spin_unlock_irqrestore(&agent->lock, flags);
flush_workqueue(agent->qp_info->port_priv->wq);
list_for_each_entry_safe(rmpp_recv, temp_rmpp_recv,
&agent->rmpp_list, list) {
list_del(&rmpp_recv->list);
- if (rmpp_recv->state != RMPP_STATE_COMPLETE)
- ib_free_recv_mad(rmpp_recv->rmpp_wc);
destroy_rmpp_recv(rmpp_recv);
}
}
unsigned long flags;
spin_lock_irqsave(&rmpp_recv->agent->lock, flags);
+ if (rmpp_recv->state == RMPP_STATE_CANCELING) {
+ spin_unlock_irqrestore(&rmpp_recv->agent->lock, flags);
+ return;
+ }
list_del(&rmpp_recv->list);
spin_unlock_irqrestore(&rmpp_recv->agent->lock, flags);
destroy_rmpp_recv(rmpp_recv);
#include <linux/device.h>
#include <linux/err.h>
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/file.h>
#include <linux/mount.h>
#include <linux/cdev.h>
#include <linux/mutex.h>
#include <linux/kref.h>
#include <linux/compat.h>
+#include <linux/sched.h>
#include <linux/semaphore.h>
#include <asm/uaccess.h>
#include <linux/err.h>
#include <linux/fs.h>
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/file.h>
#include <linux/mount.h>
#include <linux/cdev.h>
vma->vm_start, vma->vm_end, *count);
}
-static struct vm_operations_struct vm_ops = {
+static const struct vm_operations_struct vm_ops = {
.open = ehca_mm_open,
.close = ehca_mm_close,
};
return 0;
}
-static struct vm_operations_struct ipath_file_vm_ops = {
+static const struct vm_operations_struct ipath_file_vm_ops = {
.fault = ipath_file_vma_fault,
};
kref_put(&ip->ref, ipath_release_mmap_info);
}
-static struct vm_operations_struct ipath_vm_ops = {
+static const struct vm_operations_struct ipath_vm_ops = {
.open = ipath_vma_open,
.close = ipath_vma_close,
};
spin_unlock_irq(&catas_lock);
list_for_each_entry_safe(dev, tmpdev, &tlist, catas_err.list) {
+ struct pci_dev *pdev = dev->pdev;
ret = __mthca_restart_one(dev->pdev);
+ /* 'dev' now is not valid */
if (ret)
- mthca_err(dev, "Reset failed (%d)\n", ret);
- else
- mthca_dbg(dev, "Reset succeeded\n");
+ printk(KERN_ERR "mthca %s: Reset failed (%d)\n",
+ pci_name(pdev), ret);
+ else {
+ struct mthca_dev *d = pci_get_drvdata(pdev);
+ mthca_dbg(d, "Reset succeeded\n");
+ }
}
mutex_unlock(&mthca_device_mutex);
.ndo_set_mac_address = nes_netdev_set_mac_address,
.ndo_set_multicast_list = nes_netdev_set_multicast_list,
.ndo_change_mtu = nes_netdev_change_mtu,
- .ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
.ndo_vlan_rx_register = nes_netdev_vlan_rx_register,
};
{
struct ipoib_dev_priv *priv = container_of(work, struct ipoib_dev_priv,
carrier_on_task);
+ struct ib_port_attr attr;
/*
* Take rtnl_lock to avoid racing with ipoib_stop() and
* turning the carrier back on while a device is being
* removed.
*/
+ if (ib_query_port(priv->ca, priv->port, &attr) ||
+ attr.state != IB_PORT_ACTIVE) {
+ ipoib_dbg(priv, "Keeping carrier off until IB port is active\n");
+ return;
+ }
+
rtnl_lock();
netif_carrier_on(priv->dev);
rtnl_unlock();
#define EVDEV_BUFFER_SIZE 64
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/random.h>
#include <linux/major.h>
#include <linux/proc_fs.h>
+#include <linux/sched.h>
#include <linux/seq_file.h>
#include <linux/poll.h>
#include <linux/device.h>
} \
} while (0)
+#ifdef CONFIG_PM
static void input_dev_reset(struct input_dev *dev, bool activate)
{
if (!dev->event)
}
}
-#ifdef CONFIG_PM
static int input_dev_suspend(struct device *dev)
{
struct input_dev *input_dev = to_input_dev(dev);
#include <linux/input.h>
#include <linux/kernel.h>
#include <linux/major.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/mm.h>
#include <linux/miscdevice.h>
config INPUT_WINBOND_CIR
tristate "Winbond IR remote control"
depends on X86 && PNP
+ select NEW_LEDS
select LEDS_CLASS
select BITREVERSE
help
* - first public version
*/
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/init.h>
#define MOUSEDEV_MINORS 32
#define MOUSEDEV_MIX 31
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/smp_lock.h>
#include <linux/poll.h>
#else
#include <linux/fs.h>
#endif
+#include <linux/sched.h>
#include <linux/isdnif.h>
#include <net/net_namespace.h>
#include "isdn_divert.h"
depends on PCI
select MISDN_IPAC
select ISDN_HDLC
+ select ISDN_I4L
help
Enable support for Traverse Technologies NETJet PCI cards.
endif
config ISDN_HDLC
- tristate
- depends on HISAX_ST5481
+ tristate
select CRC_CCITT
select BITREVERSE
}
static int data_sock_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int len)
+ char __user *optval, unsigned int len)
{
struct sock *sk = sock->sk;
int err = 0, opt = 0;
tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
depends on LEDS_CLASS && I2C
help
- This option enables support for LEDs connected to the National
- Semiconductor LP3944 Lighting Management Unit (LMU) also known as
- Fun Light Chip.
+ This option enables support for LEDs connected to the National
+ Semiconductor LP3944 Lighting Management Unit (LMU) also known as
+ Fun Light Chip.
To compile this driver as a module, choose M here: the
module will be called leds-lp3944.
LED driver chips accessed via the I2C bus. Supported
devices include PCA9550, PCA9551, PCA9552, and PCA9553.
+config LEDS_WM831X_STATUS
+ tristate "LED support for status LEDs on WM831x PMICs"
+ depends on LEDS_CLASS && MFD_WM831X
+ help
+ This option enables support for the status LEDs of the WM831x
+ series of PMICs.
+
config LEDS_WM8350
tristate "LED Support for WM8350 AudioPlus PMIC"
depends on LEDS_CLASS && MFD_WM8350
obj-$(CONFIG_LEDS_FSG) += leds-fsg.o
obj-$(CONFIG_LEDS_PCA955X) += leds-pca955x.o
obj-$(CONFIG_LEDS_DA903X) += leds-da903x.o
+obj-$(CONFIG_LEDS_WM831X_STATUS) += leds-wm831x-status.o
obj-$(CONFIG_LEDS_WM8350) += leds-wm8350.o
obj-$(CONFIG_LEDS_PWM) += leds-pwm.o
.flags = LED_CORE_SUSPENDRESUME,
};
-static int __init clevo_mail_led_probe(struct platform_device *pdev)
+static int __devinit clevo_mail_led_probe(struct platform_device *pdev)
{
return led_classdev_register(&pdev->dev, &clevo_mail_led);
}
}
static struct led_classdev qube_front_led = {
- .name = "qube-front",
+ .name = "qube::front",
.brightness = LED_FULL,
.brightness_set = qube_front_led_set,
.default_trigger = "ide-disk",
}
static struct led_classdev raq_web_led = {
- .name = "raq-web",
+ .name = "raq::web",
.brightness_set = raq_web_led_set,
};
}
static struct led_classdev raq_power_off_led = {
- .name = "raq-power-off",
+ .name = "raq::power-off",
.brightness_set = raq_power_off_led_set,
.default_trigger = "power-off",
};
/* skip leds that aren't available */
if (!gpio_is_valid(template->gpio)) {
- printk(KERN_INFO "Skipping unavilable LED gpio %d (%s)\n",
+ printk(KERN_INFO "Skipping unavailable LED gpio %d (%s)\n",
template->gpio, template->name);
return 0;
}
#include <linux/workqueue.h>
#include <linux/leds-pca9532.h>
-static const unsigned short normal_i2c[] = { /*0x60,*/ I2C_CLIENT_END};
-I2C_CLIENT_INSMOD_1(pca9532);
-
#define PCA9532_REG_PSC(i) (0x2+(i)*2)
#define PCA9532_REG_PWM(i) (0x3+(i)*2)
#define PCA9532_REG_LS0 0x6
struct i2c_client *client;
struct pca9532_led leds[16];
struct mutex update_lock;
- struct input_dev *idev;
+ struct input_dev *idev;
struct work_struct work;
u8 pwm[2];
u8 psc[2];
static struct i2c_driver pca9532_driver = {
.driver = {
- .name = "pca9532",
+ .name = "pca9532",
},
- .probe = pca9532_probe,
+ .probe = pca9532_probe,
.remove = pca9532_remove,
.id_table = pca9532_id,
};
if (*delay_on == 0 && *delay_off == 0) {
/* led subsystem ask us for a blink rate */
- *delay_on = 1000;
+ *delay_on = 1000;
*delay_off = 1000;
}
if (*delay_on != *delay_off || *delay_on > 1690 || *delay_on < 6)
break;
case PCA9532_TYPE_LED:
led->state = pled->state;
- led->name = pled->name;
+ led->name = pled->name;
led->ldev.name = led->name;
led->ldev.brightness = LED_OFF;
led->ldev.brightness_set = pca9532_set_brightness;
data->idev->name = pled->name;
data->idev->phys = "i2c/pca9532";
data->idev->id.bustype = BUS_HOST;
- data->idev->id.vendor = 0x001f;
+ data->idev->id.vendor = 0x001f;
data->idev->id.product = 0x0001;
data->idev->id.version = 0x0100;
data->idev->evbit[0] = BIT_MASK(EV_SND);
--- /dev/null
+/*
+ * LED driver for WM831x status LEDs
+ *
+ * Copyright(C) 2009 Wolfson Microelectronics PLC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/err.h>
+#include <linux/mfd/wm831x/core.h>
+#include <linux/mfd/wm831x/pdata.h>
+#include <linux/mfd/wm831x/status.h>
+
+
+struct wm831x_status {
+ struct led_classdev cdev;
+ struct wm831x *wm831x;
+ struct work_struct work;
+ struct mutex mutex;
+
+ spinlock_t value_lock;
+ int reg; /* Control register */
+ int reg_val; /* Control register value */
+
+ int blink;
+ int blink_time;
+ int blink_cyc;
+ int src;
+ enum led_brightness brightness;
+};
+
+#define to_wm831x_status(led_cdev) \
+ container_of(led_cdev, struct wm831x_status, cdev)
+
+static void wm831x_status_work(struct work_struct *work)
+{
+ struct wm831x_status *led = container_of(work, struct wm831x_status,
+ work);
+ unsigned long flags;
+
+ mutex_lock(&led->mutex);
+
+ led->reg_val &= ~(WM831X_LED_SRC_MASK | WM831X_LED_MODE_MASK |
+ WM831X_LED_DUTY_CYC_MASK | WM831X_LED_DUR_MASK);
+
+ spin_lock_irqsave(&led->value_lock, flags);
+
+ led->reg_val |= led->src << WM831X_LED_SRC_SHIFT;
+ if (led->blink) {
+ led->reg_val |= 2 << WM831X_LED_MODE_SHIFT;
+ led->reg_val |= led->blink_time << WM831X_LED_DUR_SHIFT;
+ led->reg_val |= led->blink_cyc;
+ } else {
+ if (led->brightness != LED_OFF)
+ led->reg_val |= 1 << WM831X_LED_MODE_SHIFT;
+ }
+
+ spin_unlock_irqrestore(&led->value_lock, flags);
+
+ wm831x_reg_write(led->wm831x, led->reg, led->reg_val);
+
+ mutex_unlock(&led->mutex);
+}
+
+static void wm831x_status_set(struct led_classdev *led_cdev,
+ enum led_brightness value)
+{
+ struct wm831x_status *led = to_wm831x_status(led_cdev);
+ unsigned long flags;
+
+ spin_lock_irqsave(&led->value_lock, flags);
+ led->brightness = value;
+ if (value == LED_OFF)
+ led->blink = 0;
+ schedule_work(&led->work);
+ spin_unlock_irqrestore(&led->value_lock, flags);
+}
+
+static int wm831x_status_blink_set(struct led_classdev *led_cdev,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ struct wm831x_status *led = to_wm831x_status(led_cdev);
+ unsigned long flags;
+ int ret = 0;
+
+ /* Pick some defaults if we've not been given times */
+ if (*delay_on == 0 && *delay_off == 0) {
+ *delay_on = 250;
+ *delay_off = 250;
+ }
+
+ spin_lock_irqsave(&led->value_lock, flags);
+
+ /* We only have a limited selection of settings, see if we can
+ * support the configuration we're being given */
+ switch (*delay_on) {
+ case 1000:
+ led->blink_time = 0;
+ break;
+ case 250:
+ led->blink_time = 1;
+ break;
+ case 125:
+ led->blink_time = 2;
+ break;
+ case 62:
+ case 63:
+ /* Actually 62.5ms */
+ led->blink_time = 3;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ if (ret == 0) {
+ switch (*delay_off / *delay_on) {
+ case 1:
+ led->blink_cyc = 0;
+ break;
+ case 3:
+ led->blink_cyc = 1;
+ break;
+ case 4:
+ led->blink_cyc = 2;
+ break;
+ case 8:
+ led->blink_cyc = 3;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+ }
+
+ if (ret == 0)
+ led->blink = 1;
+ else
+ led->blink = 0;
+
+ /* Always update; if we fail turn off blinking since we expect
+ * a software fallback. */
+ schedule_work(&led->work);
+
+ spin_unlock_irqrestore(&led->value_lock, flags);
+
+ return ret;
+}
+
+static const char *led_src_texts[] = {
+ "otp",
+ "power",
+ "charger",
+ "soft",
+};
+
+static ssize_t wm831x_status_src_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct led_classdev *led_cdev = dev_get_drvdata(dev);
+ struct wm831x_status *led = to_wm831x_status(led_cdev);
+ int i;
+ ssize_t ret = 0;
+
+ mutex_lock(&led->mutex);
+
+ for (i = 0; i < ARRAY_SIZE(led_src_texts); i++)
+ if (i == led->src)
+ ret += sprintf(&buf[ret], "[%s] ", led_src_texts[i]);
+ else
+ ret += sprintf(&buf[ret], "%s ", led_src_texts[i]);
+
+ mutex_unlock(&led->mutex);
+
+ ret += sprintf(&buf[ret], "\n");
+
+ return ret;
+}
+
+static ssize_t wm831x_status_src_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t size)
+{
+ struct led_classdev *led_cdev = dev_get_drvdata(dev);
+ struct wm831x_status *led = to_wm831x_status(led_cdev);
+ char name[20];
+ int i;
+ size_t len;
+
+ name[sizeof(name) - 1] = '\0';
+ strncpy(name, buf, sizeof(name) - 1);
+ len = strlen(name);
+
+ if (len && name[len - 1] == '\n')
+ name[len - 1] = '\0';
+
+ for (i = 0; i < ARRAY_SIZE(led_src_texts); i++) {
+ if (!strcmp(name, led_src_texts[i])) {
+ mutex_lock(&led->mutex);
+
+ led->src = i;
+ schedule_work(&led->work);
+
+ mutex_unlock(&led->mutex);
+ }
+ }
+
+ return size;
+}
+
+static DEVICE_ATTR(src, 0644, wm831x_status_src_show, wm831x_status_src_store);
+
+static int wm831x_status_probe(struct platform_device *pdev)
+{
+ struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent);
+ struct wm831x_pdata *chip_pdata;
+ struct wm831x_status_pdata pdata;
+ struct wm831x_status *drvdata;
+ struct resource *res;
+ int id = pdev->id % ARRAY_SIZE(chip_pdata->status);
+ int ret;
+
+ res = platform_get_resource(pdev, IORESOURCE_IO, 0);
+ if (res == NULL) {
+ dev_err(&pdev->dev, "No I/O resource\n");
+ ret = -EINVAL;
+ goto err;
+ }
+
+ drvdata = kzalloc(sizeof(struct wm831x_status), GFP_KERNEL);
+ if (!drvdata)
+ return -ENOMEM;
+ dev_set_drvdata(&pdev->dev, drvdata);
+
+ drvdata->wm831x = wm831x;
+ drvdata->reg = res->start;
+
+ if (wm831x->dev->platform_data)
+ chip_pdata = wm831x->dev->platform_data;
+ else
+ chip_pdata = NULL;
+
+ memset(&pdata, 0, sizeof(pdata));
+ if (chip_pdata && chip_pdata->status[id])
+ memcpy(&pdata, chip_pdata->status[id], sizeof(pdata));
+ else
+ pdata.name = dev_name(&pdev->dev);
+
+ mutex_init(&drvdata->mutex);
+ INIT_WORK(&drvdata->work, wm831x_status_work);
+ spin_lock_init(&drvdata->value_lock);
+
+ /* We cache the configuration register and read startup values
+ * from it. */
+ drvdata->reg_val = wm831x_reg_read(wm831x, drvdata->reg);
+
+ if (drvdata->reg_val & WM831X_LED_MODE_MASK)
+ drvdata->brightness = LED_FULL;
+ else
+ drvdata->brightness = LED_OFF;
+
+ /* Set a default source if configured, otherwise leave the
+ * current hardware setting.
+ */
+ if (pdata.default_src == WM831X_STATUS_PRESERVE) {
+ drvdata->src = drvdata->reg_val;
+ drvdata->src &= WM831X_LED_SRC_MASK;
+ drvdata->src >>= WM831X_LED_SRC_SHIFT;
+ } else {
+ drvdata->src = pdata.default_src - 1;
+ }
+
+ drvdata->cdev.name = pdata.name;
+ drvdata->cdev.default_trigger = pdata.default_trigger;
+ drvdata->cdev.brightness_set = wm831x_status_set;
+ drvdata->cdev.blink_set = wm831x_status_blink_set;
+
+ ret = led_classdev_register(wm831x->dev, &drvdata->cdev);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to register LED: %d\n", ret);
+ goto err_led;
+ }
+
+ ret = device_create_file(drvdata->cdev.dev, &dev_attr_src);
+ if (ret != 0)
+ dev_err(&pdev->dev,
+ "No source control for LED: %d\n", ret);
+
+ return 0;
+
+err_led:
+ led_classdev_unregister(&drvdata->cdev);
+ kfree(drvdata);
+err:
+ return ret;
+}
+
+static int wm831x_status_remove(struct platform_device *pdev)
+{
+ struct wm831x_status *drvdata = platform_get_drvdata(pdev);
+
+ device_remove_file(drvdata->cdev.dev, &dev_attr_src);
+ led_classdev_unregister(&drvdata->cdev);
+ kfree(drvdata);
+
+ return 0;
+}
+
+static struct platform_driver wm831x_status_driver = {
+ .driver = {
+ .name = "wm831x-status",
+ .owner = THIS_MODULE,
+ },
+ .probe = wm831x_status_probe,
+ .remove = wm831x_status_remove,
+};
+
+static int __devinit wm831x_status_init(void)
+{
+ return platform_driver_register(&wm831x_status_driver);
+}
+module_init(wm831x_status_init);
+
+static void wm831x_status_exit(void)
+{
+ platform_driver_unregister(&wm831x_status_driver);
+}
+module_exit(wm831x_status_exit);
+
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
+MODULE_DESCRIPTION("WM831x status LED driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:wm831x-status");
struct gpio_trig_data, work);
int tmp;
- if (!gpio_data->gpio)
- return;
-
- tmp = gpio_get_value(gpio_data->gpio);
- if (gpio_data->inverted)
- tmp = !tmp;
-
- if (tmp) {
- if (gpio_data->desired_brightness)
- led_set_brightness(gpio_data->led,
- gpio_data->desired_brightness);
- else
- led_set_brightness(gpio_data->led, LED_FULL);
- } else {
- led_set_brightness(gpio_data->led, LED_OFF);
- }
+ if (!gpio_data->gpio)
+ return;
+
+ tmp = gpio_get_value(gpio_data->gpio);
+ if (gpio_data->inverted)
+ tmp = !tmp;
+
+ if (tmp) {
+ if (gpio_data->desired_brightness)
+ led_set_brightness(gpio_data->led,
+ gpio_data->desired_brightness);
+ else
+ led_set_brightness(gpio_data->led, LED_FULL);
+ } else {
+ led_set_brightness(gpio_data->led, LED_OFF);
+ }
}
static ssize_t gpio_trig_brightness_show(struct device *dev,
* uses: reading and writing a character device called /dev/lguest. All the
* work happens in the read(), write() and close() routines:
*/
-static struct file_operations lguest_fops = {
+static const struct file_operations lguest_fops = {
.owner = THIS_MODULE,
.release = close,
.write = write,
return data;
}
+static struct i2c_driver thermostat_driver;
+
static int
attach_thermostat(struct i2c_adapter *adapter)
{
* Let i2c-core delete that device on driver removal.
* This is safe because i2c-core holds the core_lock mutex for us.
*/
- list_add_tail(&client->detected, &client->driver->clients);
+ list_add_tail(&client->detected, &thermostat_driver.clients);
return 0;
}
},
};
+static struct i2c_driver therm_pm72_driver;
+
/*
* Utility function to create an i2c_client structure and
* attach it to one of u3 adapters
* Let i2c-core delete that device on driver removal.
* This is safe because i2c-core holds the core_lock mutex for us.
*/
- list_add_tail(&clt->detected, &clt->driver->clients);
+ list_add_tail(&clt->detected, &therm_pm72_driver.clients);
return clt;
}
}
static struct led_classdev pmu_led = {
- .name = "pmu-front-led",
+ .name = "pmu-led::front",
#ifdef CONFIG_ADB_PMU_LED_IDE
.default_trigger = "ide-disk",
#endif
return rc;
}
+static struct i2c_driver wf_lm75_driver;
+
static struct i2c_client *wf_lm75_create(struct i2c_adapter *adapter,
u8 addr, int ds1775,
const char *loc)
* Let i2c-core delete that device on driver removal.
* This is safe because i2c-core holds the core_lock mutex for us.
*/
- list_add_tail(&client->detected, &client->driver->clients);
+ list_add_tail(&client->detected, &wf_lm75_driver.clients);
return client;
fail:
return NULL;
return rc;
}
+static struct i2c_driver wf_max6690_driver;
+
static struct i2c_client *wf_max6690_create(struct i2c_adapter *adapter,
u8 addr, const char *loc)
{
* Let i2c-core delete that device on driver removal.
* This is safe because i2c-core holds the core_lock mutex for us.
*/
- list_add_tail(&client->detected, &client->driver->clients);
+ list_add_tail(&client->detected, &wf_max6690_driver.clients);
return client;
fail:
.owner = THIS_MODULE,
};
+static struct i2c_driver wf_sat_driver;
+
static void wf_sat_create(struct i2c_adapter *adapter, struct device_node *dev)
{
struct i2c_board_info info;
* Let i2c-core delete that device on driver removal.
* This is safe because i2c-core holds the core_lock mutex for us.
*/
- list_add_tail(&client->detected, &client->driver->clients);
+ list_add_tail(&client->detected, &wf_sat_driver.clients);
}
static int wf_sat_probe(struct i2c_client *client,
select MD_RAID6_PQ
select ASYNC_MEMCPY
select ASYNC_XOR
+ select ASYNC_PQ
+ select ASYNC_RAID6_RECOV
---help---
A RAID-5 set of N drives with a capacity of C MB per drive provides
the capacity of C * (N - 1) MB, and protects against a failure
If unsure, say Y.
+config MULTICORE_RAID456
+ bool "RAID-4/RAID-5/RAID-6 Multicore processing (EXPERIMENTAL)"
+ depends on MD_RAID456
+ depends on SMP
+ depends on EXPERIMENTAL
+ ---help---
+ Enable the raid456 module to dispatch per-stripe raid operations to a
+ thread pool.
+
+ If unsure, say N.
+
config MD_RAID6_PQ
tristate
+config ASYNC_RAID6_TEST
+ tristate "Self test for hardware accelerated raid6 recovery"
+ depends on MD_RAID6_PQ
+ select ASYNC_RAID6_RECOV
+ ---help---
+ This is a one-shot self test that permutes through the
+ recovery of all the possible two disk failure scenarios for a
+ N-disk array. Recovery is performed with the asynchronous
+ raid6 recovery routines, and will optionally use an offload
+ engine if one is available.
+
+ If unsure, say N.
+
config MD_MULTIPATH
tristate "Multipath I/O support"
depends on BLK_DEV_MD
* allocated while we're using it
*/
static int bitmap_checkpage(struct bitmap *bitmap, unsigned long page, int create)
+__releases(bitmap->lock)
+__acquires(bitmap->lock)
{
unsigned char *mappage;
return 0;
bad_alignment:
- rcu_read_unlock();
return -EINVAL;
}
static bitmap_counter_t *bitmap_get_counter(struct bitmap *bitmap,
sector_t offset, int *blocks,
int create)
+__releases(bitmap->lock)
+__acquires(bitmap->lock)
{
/* If 'create', we might release the lock and reclaim it.
* The lock must have been taken with interrupts enabled.
* This is the connector callback that delivers data
* that was sent from userspace.
*/
-static void cn_ulog_callback(void *data)
+static void cn_ulog_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
- struct cn_msg *msg = (struct cn_msg *)data;
struct dm_ulog_request *tfr = (struct dm_ulog_request *)(msg + 1);
+ if (!cap_raised(nsp->eff_cap, CAP_SYS_ADMIN))
+ return;
+
spin_lock(&receiving_list_lock);
if (msg->len == 0)
fill_pkg(msg, NULL);
/*
* A list of ios that arrived while we were suspended.
*/
- atomic_t pending[2];
+ atomic_t pending;
wait_queue_head_t wait;
struct work_struct work;
struct bio_list deferred;
{
struct mapped_device *md = io->md;
int cpu;
- int rw = bio_data_dir(io->bio);
io->start_time = jiffies;
cpu = part_stat_lock();
part_round_stats(cpu, &dm_disk(md)->part0);
part_stat_unlock();
- dm_disk(md)->part0.in_flight[rw] = atomic_inc_return(&md->pending[rw]);
+ dm_disk(md)->part0.in_flight = atomic_inc_return(&md->pending);
}
static void end_io_acct(struct dm_io *io)
* After this is decremented the bio must not be touched if it is
* a barrier.
*/
- dm_disk(md)->part0.in_flight[rw] = pending =
- atomic_dec_return(&md->pending[rw]);
- pending += atomic_read(&md->pending[rw^0x1]);
+ dm_disk(md)->part0.in_flight = pending =
+ atomic_dec_return(&md->pending);
/* nudge anyone waiting on suspend queue */
if (!pending)
if (!md->disk)
goto bad_disk;
- atomic_set(&md->pending[0], 0);
- atomic_set(&md->pending[1], 0);
+ atomic_set(&md->pending, 0);
init_waitqueue_head(&md->wait);
INIT_WORK(&md->work, dm_wq_work);
init_waitqueue_head(&md->eventq);
break;
}
spin_unlock_irqrestore(q->queue_lock, flags);
- } else if (!atomic_read(&md->pending[0]) &&
- !atomic_read(&md->pending[1]))
+ } else if (!atomic_read(&md->pending))
break;
if (interruptible == TASK_INTERRUPTIBLE &&
linear_conf_t *conf;
int i, ret = 0;
+ if (mddev_congested(mddev, bits))
+ return 1;
+
rcu_read_lock();
conf = rcu_dereference(mddev->private);
mddev->pers->quiesce(mddev, 0);
}
+int mddev_congested(mddev_t *mddev, int bits)
+{
+ return mddev->suspended;
+}
+EXPORT_SYMBOL(mddev_congested);
+
static inline mddev_t *mddev_get(mddev_t *mddev)
{
set_bit(MD_RECOVERY_RUNNING, &mddev->recovery);
mddev->sync_thread = md_register_thread(md_do_sync,
mddev,
- "%s_resync");
+ "resync");
if (!mddev->sync_thread) {
printk(KERN_ERR "%s: could not start resync"
" thread...\n",
static int get_array_info(mddev_t * mddev, void __user * arg)
{
mdu_array_info_t info;
- int nr,working,active,failed,spare;
+ int nr,working,insync,failed,spare;
mdk_rdev_t *rdev;
- nr=working=active=failed=spare=0;
+ nr=working=insync=failed=spare=0;
list_for_each_entry(rdev, &mddev->disks, same_set) {
nr++;
if (test_bit(Faulty, &rdev->flags))
else {
working++;
if (test_bit(In_sync, &rdev->flags))
- active++;
+ insync++;
else
spare++;
}
info.state = (1<<MD_SB_CLEAN);
if (mddev->bitmap && mddev->bitmap_offset)
info.state = (1<<MD_SB_BITMAP_PRESENT);
- info.active_disks = active;
+ info.active_disks = insync;
info.working_disks = working;
info.failed_disks = failed;
info.spare_disks = spare;
if (!list_empty(&mddev->disks)) {
mdk_rdev_t *rdev0 = list_entry(mddev->disks.next,
mdk_rdev_t, same_set);
- int err = super_types[mddev->major_version]
+ err = super_types[mddev->major_version]
.load_super(rdev, rdev0, mddev->minor_version);
if (err < 0) {
printk(KERN_WARNING
thread->run = run;
thread->mddev = mddev;
thread->timeout = MAX_SCHEDULE_TIMEOUT;
- thread->tsk = kthread_run(md_thread, thread, name, mdname(thread->mddev));
+ thread->tsk = kthread_run(md_thread, thread,
+ "%s_%s",
+ mdname(thread->mddev),
+ name ?: mddev->pers->name);
if (IS_ERR(thread->tsk)) {
kfree(thread);
return NULL;
}
mddev->sync_thread = md_register_thread(md_do_sync,
mddev,
- "%s_resync");
+ "resync");
if (!mddev->sync_thread) {
printk(KERN_ERR "%s: could not start resync"
" thread...\n",
extern void md_done_sync(mddev_t *mddev, int blocks, int ok);
extern void md_error(mddev_t *mddev, mdk_rdev_t *rdev);
+extern int mddev_congested(mddev_t *mddev, int bits);
extern void md_super_write(mddev_t *mddev, mdk_rdev_t *rdev,
sector_t sector, int size, struct page *page);
extern void md_super_wait(mddev_t *mddev);
}
mp_bh = mempool_alloc(conf->pool, GFP_NOIO);
- memset(mp_bh, 0, sizeof(*mp_bh));
mp_bh->master_bio = bio;
mp_bh->mddev = mddev;
multipath_conf_t *conf = mddev->private;
int i, ret = 0;
+ if (mddev_congested(mddev, bits))
+ return 1;
+
rcu_read_lock();
for (i = 0; i < mddev->raid_disks ; i++) {
mdk_rdev_t *rdev = rcu_dereference(conf->multipaths[i].rdev);
}
{
- mddev->thread = md_register_thread(multipathd, mddev, "%s_multipath");
+ mddev->thread = md_register_thread(multipathd, mddev, NULL);
if (!mddev->thread) {
printk(KERN_ERR "multipath: couldn't allocate thread"
" for %s\n", mdname(mddev));
mdk_rdev_t **devlist = conf->devlist;
int i, ret = 0;
+ if (mddev_congested(mddev, bits))
+ return 1;
+
for (i = 0; i < mddev->raid_disks && !ret ; i++) {
struct request_queue *q = bdev_get_queue(devlist[i]->bdev);
static int create_strip_zones(mddev_t *mddev)
{
- int i, c, j, err;
+ int i, c, err;
sector_t curr_zone_end, sectors;
mdk_rdev_t *smallest, *rdev1, *rdev2, *rdev, **dev;
struct strip_zone *zone;
/* now do the other zones */
for (i = 1; i < conf->nr_strip_zones; i++)
{
+ int j;
+
zone = conf->strip_zone + i;
dev = conf->devlist + i * mddev->raid_disks;
c = 0;
for (j=0; j<cnt; j++) {
- char b[BDEVNAME_SIZE];
rdev = conf->devlist[j];
printk(KERN_INFO "raid0: checking %s ...",
bdevname(rdev->bdev, b));
conf_t *conf = mddev->private;
int i, ret = 0;
+ if (mddev_congested(mddev, bits))
+ return 1;
+
rcu_read_lock();
for (i = 0; i < mddev->raid_disks; i++) {
mdk_rdev_t *rdev = rcu_dereference(conf->mirrors[i].rdev);
read_bio->bi_sector = r1_bio->sector + mirror->rdev->data_offset;
read_bio->bi_bdev = mirror->rdev->bdev;
read_bio->bi_end_io = raid1_end_read_request;
- read_bio->bi_rw = READ | do_sync;
+ read_bio->bi_rw = READ | (do_sync << BIO_RW_SYNCIO);
read_bio->bi_private = r1_bio;
generic_make_request(read_bio);
mbio->bi_sector = r1_bio->sector + conf->mirrors[i].rdev->data_offset;
mbio->bi_bdev = conf->mirrors[i].rdev->bdev;
mbio->bi_end_io = raid1_end_write_request;
- mbio->bi_rw = WRITE | do_barriers | do_sync;
+ mbio->bi_rw = WRITE | (do_barriers << BIO_RW_BARRIER) |
+ (do_sync << BIO_RW_SYNCIO);
mbio->bi_private = r1_bio;
if (behind_pages) {
conf->mirrors[i].rdev->data_offset;
bio->bi_bdev = conf->mirrors[i].rdev->bdev;
bio->bi_end_io = raid1_end_write_request;
- bio->bi_rw = WRITE | do_sync;
+ bio->bi_rw = WRITE |
+ (do_sync << BIO_RW_SYNCIO);
bio->bi_private = r1_bio;
r1_bio->bios[i] = bio;
generic_make_request(bio);
bio->bi_sector = r1_bio->sector + rdev->data_offset;
bio->bi_bdev = rdev->bdev;
bio->bi_end_io = raid1_end_read_request;
- bio->bi_rw = READ | do_sync;
+ bio->bi_rw = READ | (do_sync << BIO_RW_SYNCIO);
bio->bi_private = r1_bio;
unplug = 1;
generic_make_request(bio);
conf->last_used = j;
- mddev->thread = md_register_thread(raid1d, mddev, "%s_raid1");
+ mddev->thread = md_register_thread(raid1d, mddev, NULL);
if (!mddev->thread) {
printk(KERN_ERR
"raid1: couldn't allocate thread for %s\n",
conf_t *conf = mddev->private;
int i, ret = 0;
+ if (mddev_congested(mddev, bits))
+ return 1;
rcu_read_lock();
for (i = 0; i < mddev->raid_disks && ret == 0; i++) {
mdk_rdev_t *rdev = rcu_dereference(conf->mirrors[i].rdev);
mirror->rdev->data_offset;
read_bio->bi_bdev = mirror->rdev->bdev;
read_bio->bi_end_io = raid10_end_read_request;
- read_bio->bi_rw = READ | do_sync;
+ read_bio->bi_rw = READ | (do_sync << BIO_RW_SYNCIO);
read_bio->bi_private = r10_bio;
generic_make_request(read_bio);
conf->mirrors[d].rdev->data_offset;
mbio->bi_bdev = conf->mirrors[d].rdev->bdev;
mbio->bi_end_io = raid10_end_write_request;
- mbio->bi_rw = WRITE | do_sync;
+ mbio->bi_rw = WRITE | (do_sync << BIO_RW_SYNCIO);
mbio->bi_private = r10_bio;
atomic_inc(&r10_bio->remaining);
bio->bi_sector = r10_bio->devs[r10_bio->read_slot].addr
+ rdev->data_offset;
bio->bi_bdev = rdev->bdev;
- bio->bi_rw = READ | do_sync;
+ bio->bi_rw = READ | (do_sync << BIO_RW_SYNCIO);
bio->bi_private = r10_bio;
bio->bi_end_io = raid10_end_read_request;
unplug = 1;
max_sync = RESYNC_PAGES << (PAGE_SHIFT-9);
if (!test_bit(MD_RECOVERY_SYNC, &mddev->recovery)) {
/* recovery... the complicated one */
- int i, j, k;
+ int j, k;
r10_bio = NULL;
for (i=0 ; i<conf->raid_disks; i++)
}
- mddev->thread = md_register_thread(raid10d, mddev, "%s_raid10");
+ mddev->thread = md_register_thread(raid10d, mddev, NULL);
if (!mddev->thread) {
printk(KERN_ERR
"raid10: couldn't allocate thread for %s\n",
#include <linux/kthread.h>
#include <linux/raid/pq.h>
#include <linux/async_tx.h>
+#include <linux/async.h>
#include <linux/seq_file.h>
+#include <linux/cpu.h>
#include "md.h"
#include "raid5.h"
#include "bitmap.h"
struct page *bio_page;
int i;
int page_offset;
+ struct async_submit_ctl submit;
+ enum async_tx_flags flags = 0;
if (bio->bi_sector >= sector)
page_offset = (signed)(bio->bi_sector - sector) * 512;
else
page_offset = (signed)(sector - bio->bi_sector) * -512;
+
+ if (frombio)
+ flags |= ASYNC_TX_FENCE;
+ init_async_submit(&submit, flags, tx, NULL, NULL, NULL);
+
bio_for_each_segment(bvl, bio, i) {
int len = bio_iovec_idx(bio, i)->bv_len;
int clen;
bio_page = bio_iovec_idx(bio, i)->bv_page;
if (frombio)
tx = async_memcpy(page, bio_page, page_offset,
- b_offset, clen,
- ASYNC_TX_DEP_ACK,
- tx, NULL, NULL);
+ b_offset, clen, &submit);
else
tx = async_memcpy(bio_page, page, b_offset,
- page_offset, clen,
- ASYNC_TX_DEP_ACK,
- tx, NULL, NULL);
+ page_offset, clen, &submit);
}
+ /* chain the operations */
+ submit.depend_tx = tx;
+
if (clen < len) /* hit end of page */
break;
page_offset += len;
{
struct dma_async_tx_descriptor *tx = NULL;
raid5_conf_t *conf = sh->raid_conf;
+ struct async_submit_ctl submit;
int i;
pr_debug("%s: stripe %llu\n", __func__,
}
atomic_inc(&sh->count);
- async_trigger_callback(ASYNC_TX_DEP_ACK | ASYNC_TX_ACK, tx,
- ops_complete_biofill, sh);
+ init_async_submit(&submit, ASYNC_TX_ACK, tx, ops_complete_biofill, sh, NULL);
+ async_trigger_callback(&submit);
}
-static void ops_complete_compute5(void *stripe_head_ref)
+static void mark_target_uptodate(struct stripe_head *sh, int target)
{
- struct stripe_head *sh = stripe_head_ref;
- int target = sh->ops.target;
- struct r5dev *tgt = &sh->dev[target];
+ struct r5dev *tgt;
- pr_debug("%s: stripe %llu\n", __func__,
- (unsigned long long)sh->sector);
+ if (target < 0)
+ return;
+ tgt = &sh->dev[target];
set_bit(R5_UPTODATE, &tgt->flags);
BUG_ON(!test_bit(R5_Wantcompute, &tgt->flags));
clear_bit(R5_Wantcompute, &tgt->flags);
+}
+
+static void ops_complete_compute(void *stripe_head_ref)
+{
+ struct stripe_head *sh = stripe_head_ref;
+
+ pr_debug("%s: stripe %llu\n", __func__,
+ (unsigned long long)sh->sector);
+
+ /* mark the computed target(s) as uptodate */
+ mark_target_uptodate(sh, sh->ops.target);
+ mark_target_uptodate(sh, sh->ops.target2);
+
clear_bit(STRIPE_COMPUTE_RUN, &sh->state);
if (sh->check_state == check_state_compute_run)
sh->check_state = check_state_compute_result;
release_stripe(sh);
}
-static struct dma_async_tx_descriptor *ops_run_compute5(struct stripe_head *sh)
+/* return a pointer to the address conversion region of the scribble buffer */
+static addr_conv_t *to_addr_conv(struct stripe_head *sh,
+ struct raid5_percpu *percpu)
+{
+ return percpu->scribble + sizeof(struct page *) * (sh->disks + 2);
+}
+
+static struct dma_async_tx_descriptor *
+ops_run_compute5(struct stripe_head *sh, struct raid5_percpu *percpu)
{
- /* kernel stack size limits the total number of disks */
int disks = sh->disks;
- struct page *xor_srcs[disks];
+ struct page **xor_srcs = percpu->scribble;
int target = sh->ops.target;
struct r5dev *tgt = &sh->dev[target];
struct page *xor_dest = tgt->page;
int count = 0;
struct dma_async_tx_descriptor *tx;
+ struct async_submit_ctl submit;
int i;
pr_debug("%s: stripe %llu block: %d\n",
atomic_inc(&sh->count);
+ init_async_submit(&submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_ZERO_DST, NULL,
+ ops_complete_compute, sh, to_addr_conv(sh, percpu));
if (unlikely(count == 1))
- tx = async_memcpy(xor_dest, xor_srcs[0], 0, 0, STRIPE_SIZE,
- 0, NULL, ops_complete_compute5, sh);
+ tx = async_memcpy(xor_dest, xor_srcs[0], 0, 0, STRIPE_SIZE, &submit);
else
- tx = async_xor(xor_dest, xor_srcs, 0, count, STRIPE_SIZE,
- ASYNC_TX_XOR_ZERO_DST, NULL,
- ops_complete_compute5, sh);
+ tx = async_xor(xor_dest, xor_srcs, 0, count, STRIPE_SIZE, &submit);
return tx;
}
+/* set_syndrome_sources - populate source buffers for gen_syndrome
+ * @srcs - (struct page *) array of size sh->disks
+ * @sh - stripe_head to parse
+ *
+ * Populates srcs in proper layout order for the stripe and returns the
+ * 'count' of sources to be used in a call to async_gen_syndrome. The P
+ * destination buffer is recorded in srcs[count] and the Q destination
+ * is recorded in srcs[count+1]].
+ */
+static int set_syndrome_sources(struct page **srcs, struct stripe_head *sh)
+{
+ int disks = sh->disks;
+ int syndrome_disks = sh->ddf_layout ? disks : (disks - 2);
+ int d0_idx = raid6_d0(sh);
+ int count;
+ int i;
+
+ for (i = 0; i < disks; i++)
+ srcs[i] = (void *)raid6_empty_zero_page;
+
+ count = 0;
+ i = d0_idx;
+ do {
+ int slot = raid6_idx_to_slot(i, sh, &count, syndrome_disks);
+
+ srcs[slot] = sh->dev[i].page;
+ i = raid6_next_disk(i, disks);
+ } while (i != d0_idx);
+ BUG_ON(count != syndrome_disks);
+
+ return count;
+}
+
+static struct dma_async_tx_descriptor *
+ops_run_compute6_1(struct stripe_head *sh, struct raid5_percpu *percpu)
+{
+ int disks = sh->disks;
+ struct page **blocks = percpu->scribble;
+ int target;
+ int qd_idx = sh->qd_idx;
+ struct dma_async_tx_descriptor *tx;
+ struct async_submit_ctl submit;
+ struct r5dev *tgt;
+ struct page *dest;
+ int i;
+ int count;
+
+ if (sh->ops.target < 0)
+ target = sh->ops.target2;
+ else if (sh->ops.target2 < 0)
+ target = sh->ops.target;
+ else
+ /* we should only have one valid target */
+ BUG();
+ BUG_ON(target < 0);
+ pr_debug("%s: stripe %llu block: %d\n",
+ __func__, (unsigned long long)sh->sector, target);
+
+ tgt = &sh->dev[target];
+ BUG_ON(!test_bit(R5_Wantcompute, &tgt->flags));
+ dest = tgt->page;
+
+ atomic_inc(&sh->count);
+
+ if (target == qd_idx) {
+ count = set_syndrome_sources(blocks, sh);
+ blocks[count] = NULL; /* regenerating p is not necessary */
+ BUG_ON(blocks[count+1] != dest); /* q should already be set */
+ init_async_submit(&submit, ASYNC_TX_FENCE, NULL,
+ ops_complete_compute, sh,
+ to_addr_conv(sh, percpu));
+ tx = async_gen_syndrome(blocks, 0, count+2, STRIPE_SIZE, &submit);
+ } else {
+ /* Compute any data- or p-drive using XOR */
+ count = 0;
+ for (i = disks; i-- ; ) {
+ if (i == target || i == qd_idx)
+ continue;
+ blocks[count++] = sh->dev[i].page;
+ }
+
+ init_async_submit(&submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_ZERO_DST,
+ NULL, ops_complete_compute, sh,
+ to_addr_conv(sh, percpu));
+ tx = async_xor(dest, blocks, 0, count, STRIPE_SIZE, &submit);
+ }
+
+ return tx;
+}
+
+static struct dma_async_tx_descriptor *
+ops_run_compute6_2(struct stripe_head *sh, struct raid5_percpu *percpu)
+{
+ int i, count, disks = sh->disks;
+ int syndrome_disks = sh->ddf_layout ? disks : disks-2;
+ int d0_idx = raid6_d0(sh);
+ int faila = -1, failb = -1;
+ int target = sh->ops.target;
+ int target2 = sh->ops.target2;
+ struct r5dev *tgt = &sh->dev[target];
+ struct r5dev *tgt2 = &sh->dev[target2];
+ struct dma_async_tx_descriptor *tx;
+ struct page **blocks = percpu->scribble;
+ struct async_submit_ctl submit;
+
+ pr_debug("%s: stripe %llu block1: %d block2: %d\n",
+ __func__, (unsigned long long)sh->sector, target, target2);
+ BUG_ON(target < 0 || target2 < 0);
+ BUG_ON(!test_bit(R5_Wantcompute, &tgt->flags));
+ BUG_ON(!test_bit(R5_Wantcompute, &tgt2->flags));
+
+ /* we need to open-code set_syndrome_sources to handle the
+ * slot number conversion for 'faila' and 'failb'
+ */
+ for (i = 0; i < disks ; i++)
+ blocks[i] = (void *)raid6_empty_zero_page;
+ count = 0;
+ i = d0_idx;
+ do {
+ int slot = raid6_idx_to_slot(i, sh, &count, syndrome_disks);
+
+ blocks[slot] = sh->dev[i].page;
+
+ if (i == target)
+ faila = slot;
+ if (i == target2)
+ failb = slot;
+ i = raid6_next_disk(i, disks);
+ } while (i != d0_idx);
+ BUG_ON(count != syndrome_disks);
+
+ BUG_ON(faila == failb);
+ if (failb < faila)
+ swap(faila, failb);
+ pr_debug("%s: stripe: %llu faila: %d failb: %d\n",
+ __func__, (unsigned long long)sh->sector, faila, failb);
+
+ atomic_inc(&sh->count);
+
+ if (failb == syndrome_disks+1) {
+ /* Q disk is one of the missing disks */
+ if (faila == syndrome_disks) {
+ /* Missing P+Q, just recompute */
+ init_async_submit(&submit, ASYNC_TX_FENCE, NULL,
+ ops_complete_compute, sh,
+ to_addr_conv(sh, percpu));
+ return async_gen_syndrome(blocks, 0, count+2,
+ STRIPE_SIZE, &submit);
+ } else {
+ struct page *dest;
+ int data_target;
+ int qd_idx = sh->qd_idx;
+
+ /* Missing D+Q: recompute D from P, then recompute Q */
+ if (target == qd_idx)
+ data_target = target2;
+ else
+ data_target = target;
+
+ count = 0;
+ for (i = disks; i-- ; ) {
+ if (i == data_target || i == qd_idx)
+ continue;
+ blocks[count++] = sh->dev[i].page;
+ }
+ dest = sh->dev[data_target].page;
+ init_async_submit(&submit,
+ ASYNC_TX_FENCE|ASYNC_TX_XOR_ZERO_DST,
+ NULL, NULL, NULL,
+ to_addr_conv(sh, percpu));
+ tx = async_xor(dest, blocks, 0, count, STRIPE_SIZE,
+ &submit);
+
+ count = set_syndrome_sources(blocks, sh);
+ init_async_submit(&submit, ASYNC_TX_FENCE, tx,
+ ops_complete_compute, sh,
+ to_addr_conv(sh, percpu));
+ return async_gen_syndrome(blocks, 0, count+2,
+ STRIPE_SIZE, &submit);
+ }
+ } else {
+ init_async_submit(&submit, ASYNC_TX_FENCE, NULL,
+ ops_complete_compute, sh,
+ to_addr_conv(sh, percpu));
+ if (failb == syndrome_disks) {
+ /* We're missing D+P. */
+ return async_raid6_datap_recov(syndrome_disks+2,
+ STRIPE_SIZE, faila,
+ blocks, &submit);
+ } else {
+ /* We're missing D+D. */
+ return async_raid6_2data_recov(syndrome_disks+2,
+ STRIPE_SIZE, faila, failb,
+ blocks, &submit);
+ }
+ }
+}
+
+
static void ops_complete_prexor(void *stripe_head_ref)
{
struct stripe_head *sh = stripe_head_ref;
}
static struct dma_async_tx_descriptor *
-ops_run_prexor(struct stripe_head *sh, struct dma_async_tx_descriptor *tx)
+ops_run_prexor(struct stripe_head *sh, struct raid5_percpu *percpu,
+ struct dma_async_tx_descriptor *tx)
{
- /* kernel stack size limits the total number of disks */
int disks = sh->disks;
- struct page *xor_srcs[disks];
+ struct page **xor_srcs = percpu->scribble;
int count = 0, pd_idx = sh->pd_idx, i;
+ struct async_submit_ctl submit;
/* existing parity data subtracted */
struct page *xor_dest = xor_srcs[count++] = sh->dev[pd_idx].page;
xor_srcs[count++] = dev->page;
}
- tx = async_xor(xor_dest, xor_srcs, 0, count, STRIPE_SIZE,
- ASYNC_TX_DEP_ACK | ASYNC_TX_XOR_DROP_DST, tx,
- ops_complete_prexor, sh);
+ init_async_submit(&submit, ASYNC_TX_FENCE|ASYNC_TX_XOR_DROP_DST, tx,
+ ops_complete_prexor, sh, to_addr_conv(sh, percpu));
+ tx = async_xor(xor_dest, xor_srcs, 0, count, STRIPE_SIZE, &submit);
return tx;
}
return tx;
}
-static void ops_complete_postxor(void *stripe_head_ref)
+static void ops_complete_reconstruct(void *stripe_head_ref)
{
struct stripe_head *sh = stripe_head_ref;
- int disks = sh->disks, i, pd_idx = sh->pd_idx;
+ int disks = sh->disks;
+ int pd_idx = sh->pd_idx;
+ int qd_idx = sh->qd_idx;
+ int i;
pr_debug("%s: stripe %llu\n", __func__,
(unsigned long long)sh->sector);
for (i = disks; i--; ) {
struct r5dev *dev = &sh->dev[i];
- if (dev->written || i == pd_idx)
+
+ if (dev->written || i == pd_idx || i == qd_idx)
set_bit(R5_UPTODATE, &dev->flags);
}
}
static void
-ops_run_postxor(struct stripe_head *sh, struct dma_async_tx_descriptor *tx)
+ops_run_reconstruct5(struct stripe_head *sh, struct raid5_percpu *percpu,
+ struct dma_async_tx_descriptor *tx)
{
- /* kernel stack size limits the total number of disks */
int disks = sh->disks;
- struct page *xor_srcs[disks];
-
+ struct page **xor_srcs = percpu->scribble;
+ struct async_submit_ctl submit;
int count = 0, pd_idx = sh->pd_idx, i;
struct page *xor_dest;
int prexor = 0;
* set ASYNC_TX_XOR_DROP_DST and ASYNC_TX_XOR_ZERO_DST
* for the synchronous xor case
*/
- flags = ASYNC_TX_DEP_ACK | ASYNC_TX_ACK |
+ flags = ASYNC_TX_ACK |
(prexor ? ASYNC_TX_XOR_DROP_DST : ASYNC_TX_XOR_ZERO_DST);
atomic_inc(&sh->count);
- if (unlikely(count == 1)) {
- flags &= ~(ASYNC_TX_XOR_DROP_DST | ASYNC_TX_XOR_ZERO_DST);
- tx = async_memcpy(xor_dest, xor_srcs[0], 0, 0, STRIPE_SIZE,
- flags, tx, ops_complete_postxor, sh);
- } else
- tx = async_xor(xor_dest, xor_srcs, 0, count, STRIPE_SIZE,
- flags, tx, ops_complete_postxor, sh);
+ init_async_submit(&submit, flags, tx, ops_complete_reconstruct, sh,
+ to_addr_conv(sh, percpu));
+ if (unlikely(count == 1))
+ tx = async_memcpy(xor_dest, xor_srcs[0], 0, 0, STRIPE_SIZE, &submit);
+ else
+ tx = async_xor(xor_dest, xor_srcs, 0, count, STRIPE_SIZE, &submit);
+}
+
+static void
+ops_run_reconstruct6(struct stripe_head *sh, struct raid5_percpu *percpu,
+ struct dma_async_tx_descriptor *tx)
+{
+ struct async_submit_ctl submit;
+ struct page **blocks = percpu->scribble;
+ int count;
+
+ pr_debug("%s: stripe %llu\n", __func__, (unsigned long long)sh->sector);
+
+ count = set_syndrome_sources(blocks, sh);
+
+ atomic_inc(&sh->count);
+
+ init_async_submit(&submit, ASYNC_TX_ACK, tx, ops_complete_reconstruct,
+ sh, to_addr_conv(sh, percpu));
+ async_gen_syndrome(blocks, 0, count+2, STRIPE_SIZE, &submit);
}
static void ops_complete_check(void *stripe_head_ref)
release_stripe(sh);
}
-static void ops_run_check(struct stripe_head *sh)
+static void ops_run_check_p(struct stripe_head *sh, struct raid5_percpu *percpu)
{
- /* kernel stack size limits the total number of disks */
int disks = sh->disks;
- struct page *xor_srcs[disks];
+ int pd_idx = sh->pd_idx;
+ int qd_idx = sh->qd_idx;
+ struct page *xor_dest;
+ struct page **xor_srcs = percpu->scribble;
struct dma_async_tx_descriptor *tx;
-
- int count = 0, pd_idx = sh->pd_idx, i;
- struct page *xor_dest = xor_srcs[count++] = sh->dev[pd_idx].page;
+ struct async_submit_ctl submit;
+ int count;
+ int i;
pr_debug("%s: stripe %llu\n", __func__,
(unsigned long long)sh->sector);
+ count = 0;
+ xor_dest = sh->dev[pd_idx].page;
+ xor_srcs[count++] = xor_dest;
for (i = disks; i--; ) {
- struct r5dev *dev = &sh->dev[i];
- if (i != pd_idx)
- xor_srcs[count++] = dev->page;
+ if (i == pd_idx || i == qd_idx)
+ continue;
+ xor_srcs[count++] = sh->dev[i].page;
}
- tx = async_xor_zero_sum(xor_dest, xor_srcs, 0, count, STRIPE_SIZE,
- &sh->ops.zero_sum_result, 0, NULL, NULL, NULL);
+ init_async_submit(&submit, 0, NULL, NULL, NULL,
+ to_addr_conv(sh, percpu));
+ tx = async_xor_val(xor_dest, xor_srcs, 0, count, STRIPE_SIZE,
+ &sh->ops.zero_sum_result, &submit);
+
+ atomic_inc(&sh->count);
+ init_async_submit(&submit, ASYNC_TX_ACK, tx, ops_complete_check, sh, NULL);
+ tx = async_trigger_callback(&submit);
+}
+
+static void ops_run_check_pq(struct stripe_head *sh, struct raid5_percpu *percpu, int checkp)
+{
+ struct page **srcs = percpu->scribble;
+ struct async_submit_ctl submit;
+ int count;
+
+ pr_debug("%s: stripe %llu checkp: %d\n", __func__,
+ (unsigned long long)sh->sector, checkp);
+
+ count = set_syndrome_sources(srcs, sh);
+ if (!checkp)
+ srcs[count] = NULL;
atomic_inc(&sh->count);
- tx = async_trigger_callback(ASYNC_TX_DEP_ACK | ASYNC_TX_ACK, tx,
- ops_complete_check, sh);
+ init_async_submit(&submit, ASYNC_TX_ACK, NULL, ops_complete_check,
+ sh, to_addr_conv(sh, percpu));
+ async_syndrome_val(srcs, 0, count+2, STRIPE_SIZE,
+ &sh->ops.zero_sum_result, percpu->spare_page, &submit);
}
-static void raid5_run_ops(struct stripe_head *sh, unsigned long ops_request)
+static void raid_run_ops(struct stripe_head *sh, unsigned long ops_request)
{
int overlap_clear = 0, i, disks = sh->disks;
struct dma_async_tx_descriptor *tx = NULL;
+ raid5_conf_t *conf = sh->raid_conf;
+ int level = conf->level;
+ struct raid5_percpu *percpu;
+ unsigned long cpu;
+ cpu = get_cpu();
+ percpu = per_cpu_ptr(conf->percpu, cpu);
if (test_bit(STRIPE_OP_BIOFILL, &ops_request)) {
ops_run_biofill(sh);
overlap_clear++;
}
if (test_bit(STRIPE_OP_COMPUTE_BLK, &ops_request)) {
- tx = ops_run_compute5(sh);
- /* terminate the chain if postxor is not set to be run */
- if (tx && !test_bit(STRIPE_OP_POSTXOR, &ops_request))
+ if (level < 6)
+ tx = ops_run_compute5(sh, percpu);
+ else {
+ if (sh->ops.target2 < 0 || sh->ops.target < 0)
+ tx = ops_run_compute6_1(sh, percpu);
+ else
+ tx = ops_run_compute6_2(sh, percpu);
+ }
+ /* terminate the chain if reconstruct is not set to be run */
+ if (tx && !test_bit(STRIPE_OP_RECONSTRUCT, &ops_request))
async_tx_ack(tx);
}
if (test_bit(STRIPE_OP_PREXOR, &ops_request))
- tx = ops_run_prexor(sh, tx);
+ tx = ops_run_prexor(sh, percpu, tx);
if (test_bit(STRIPE_OP_BIODRAIN, &ops_request)) {
tx = ops_run_biodrain(sh, tx);
overlap_clear++;
}
- if (test_bit(STRIPE_OP_POSTXOR, &ops_request))
- ops_run_postxor(sh, tx);
+ if (test_bit(STRIPE_OP_RECONSTRUCT, &ops_request)) {
+ if (level < 6)
+ ops_run_reconstruct5(sh, percpu, tx);
+ else
+ ops_run_reconstruct6(sh, percpu, tx);
+ }
- if (test_bit(STRIPE_OP_CHECK, &ops_request))
- ops_run_check(sh);
+ if (test_bit(STRIPE_OP_CHECK, &ops_request)) {
+ if (sh->check_state == check_state_run)
+ ops_run_check_p(sh, percpu);
+ else if (sh->check_state == check_state_run_q)
+ ops_run_check_pq(sh, percpu, 0);
+ else if (sh->check_state == check_state_run_pq)
+ ops_run_check_pq(sh, percpu, 1);
+ else
+ BUG();
+ }
if (overlap_clear)
for (i = disks; i--; ) {
if (test_and_clear_bit(R5_Overlap, &dev->flags))
wake_up(&sh->raid_conf->wait_for_overlap);
}
+ put_cpu();
}
static int grow_one_stripe(raid5_conf_t *conf)
return 0;
}
+/**
+ * scribble_len - return the required size of the scribble region
+ * @num - total number of disks in the array
+ *
+ * The size must be enough to contain:
+ * 1/ a struct page pointer for each device in the array +2
+ * 2/ room to convert each entry in (1) to its corresponding dma
+ * (dma_map_page()) or page (page_address()) address.
+ *
+ * Note: the +2 is for the destination buffers of the ddf/raid6 case where we
+ * calculate over all devices (not just the data blocks), using zeros in place
+ * of the P and Q blocks.
+ */
+static size_t scribble_len(int num)
+{
+ size_t len;
+
+ len = sizeof(struct page *) * (num+2) + sizeof(addr_conv_t) * (num+2);
+
+ return len;
+}
+
static int resize_stripes(raid5_conf_t *conf, int newsize)
{
/* Make all the stripes able to hold 'newsize' devices.
struct stripe_head *osh, *nsh;
LIST_HEAD(newstripes);
struct disk_info *ndisks;
+ unsigned long cpu;
int err;
struct kmem_cache *sc;
int i;
/* Step 3.
* At this point, we are holding all the stripes so the array
* is completely stalled, so now is a good time to resize
- * conf->disks.
+ * conf->disks and the scribble region
*/
ndisks = kzalloc(newsize * sizeof(struct disk_info), GFP_NOIO);
if (ndisks) {
} else
err = -ENOMEM;
+ get_online_cpus();
+ conf->scribble_len = scribble_len(newsize);
+ for_each_present_cpu(cpu) {
+ struct raid5_percpu *percpu;
+ void *scribble;
+
+ percpu = per_cpu_ptr(conf->percpu, cpu);
+ scribble = kmalloc(conf->scribble_len, GFP_NOIO);
+
+ if (scribble) {
+ kfree(percpu->scribble);
+ percpu->scribble = scribble;
+ } else {
+ err = -ENOMEM;
+ break;
+ }
+ }
+ put_online_cpus();
+
/* Step 4, return new stripes to service */
while(!list_empty(&newstripes)) {
nsh = list_entry(newstripes.next, struct stripe_head, lru);
list_del_init(&nsh->lru);
+
for (i=conf->raid_disks; i < newsize; i++)
if (nsh->dev[i].page == NULL) {
struct page *p = alloc_page(GFP_NOIO);
}
-
-/*
- * Copy data between a page in the stripe cache, and one or more bion
- * The page could align with the middle of the bio, or there could be
- * several bion, each with several bio_vecs, which cover part of the page
- * Multiple bion are linked together on bi_next. There may be extras
- * at the end of this list. We ignore them.
- */
-static void copy_data(int frombio, struct bio *bio,
- struct page *page,
- sector_t sector)
-{
- char *pa = page_address(page);
- struct bio_vec *bvl;
- int i;
- int page_offset;
-
- if (bio->bi_sector >= sector)
- page_offset = (signed)(bio->bi_sector - sector) * 512;
- else
- page_offset = (signed)(sector - bio->bi_sector) * -512;
- bio_for_each_segment(bvl, bio, i) {
- int len = bio_iovec_idx(bio,i)->bv_len;
- int clen;
- int b_offset = 0;
-
- if (page_offset < 0) {
- b_offset = -page_offset;
- page_offset += b_offset;
- len -= b_offset;
- }
-
- if (len > 0 && page_offset + len > STRIPE_SIZE)
- clen = STRIPE_SIZE - page_offset;
- else clen = len;
-
- if (clen > 0) {
- char *ba = __bio_kmap_atomic(bio, i, KM_USER0);
- if (frombio)
- memcpy(pa+page_offset, ba+b_offset, clen);
- else
- memcpy(ba+b_offset, pa+page_offset, clen);
- __bio_kunmap_atomic(ba, KM_USER0);
- }
- if (clen < len) /* hit end of page */
- break;
- page_offset += len;
- }
-}
-
-#define check_xor() do { \
- if (count == MAX_XOR_BLOCKS) { \
- xor_blocks(count, STRIPE_SIZE, dest, ptr);\
- count = 0; \
- } \
- } while(0)
-
-static void compute_parity6(struct stripe_head *sh, int method)
-{
- raid5_conf_t *conf = sh->raid_conf;
- int i, pd_idx, qd_idx, d0_idx, disks = sh->disks, count;
- int syndrome_disks = sh->ddf_layout ? disks : (disks - 2);
- struct bio *chosen;
- /**** FIX THIS: This could be very bad if disks is close to 256 ****/
- void *ptrs[syndrome_disks+2];
-
- pd_idx = sh->pd_idx;
- qd_idx = sh->qd_idx;
- d0_idx = raid6_d0(sh);
-
- pr_debug("compute_parity, stripe %llu, method %d\n",
- (unsigned long long)sh->sector, method);
-
- switch(method) {
- case READ_MODIFY_WRITE:
- BUG(); /* READ_MODIFY_WRITE N/A for RAID-6 */
- case RECONSTRUCT_WRITE:
- for (i= disks; i-- ;)
- if ( i != pd_idx && i != qd_idx && sh->dev[i].towrite ) {
- chosen = sh->dev[i].towrite;
- sh->dev[i].towrite = NULL;
-
- if (test_and_clear_bit(R5_Overlap, &sh->dev[i].flags))
- wake_up(&conf->wait_for_overlap);
-
- BUG_ON(sh->dev[i].written);
- sh->dev[i].written = chosen;
- }
- break;
- case CHECK_PARITY:
- BUG(); /* Not implemented yet */
- }
-
- for (i = disks; i--;)
- if (sh->dev[i].written) {
- sector_t sector = sh->dev[i].sector;
- struct bio *wbi = sh->dev[i].written;
- while (wbi && wbi->bi_sector < sector + STRIPE_SECTORS) {
- copy_data(1, wbi, sh->dev[i].page, sector);
- wbi = r5_next_bio(wbi, sector);
- }
-
- set_bit(R5_LOCKED, &sh->dev[i].flags);
- set_bit(R5_UPTODATE, &sh->dev[i].flags);
- }
-
- /* Note that unlike RAID-5, the ordering of the disks matters greatly.*/
-
- for (i = 0; i < disks; i++)
- ptrs[i] = (void *)raid6_empty_zero_page;
-
- count = 0;
- i = d0_idx;
- do {
- int slot = raid6_idx_to_slot(i, sh, &count, syndrome_disks);
-
- ptrs[slot] = page_address(sh->dev[i].page);
- if (slot < syndrome_disks &&
- !test_bit(R5_UPTODATE, &sh->dev[i].flags)) {
- printk(KERN_ERR "block %d/%d not uptodate "
- "on parity calc\n", i, count);
- BUG();
- }
-
- i = raid6_next_disk(i, disks);
- } while (i != d0_idx);
- BUG_ON(count != syndrome_disks);
-
- raid6_call.gen_syndrome(syndrome_disks+2, STRIPE_SIZE, ptrs);
-
- switch(method) {
- case RECONSTRUCT_WRITE:
- set_bit(R5_UPTODATE, &sh->dev[pd_idx].flags);
- set_bit(R5_UPTODATE, &sh->dev[qd_idx].flags);
- set_bit(R5_LOCKED, &sh->dev[pd_idx].flags);
- set_bit(R5_LOCKED, &sh->dev[qd_idx].flags);
- break;
- case UPDATE_PARITY:
- set_bit(R5_UPTODATE, &sh->dev[pd_idx].flags);
- set_bit(R5_UPTODATE, &sh->dev[qd_idx].flags);
- break;
- }
-}
-
-
-/* Compute one missing block */
-static void compute_block_1(struct stripe_head *sh, int dd_idx, int nozero)
-{
- int i, count, disks = sh->disks;
- void *ptr[MAX_XOR_BLOCKS], *dest, *p;
- int qd_idx = sh->qd_idx;
-
- pr_debug("compute_block_1, stripe %llu, idx %d\n",
- (unsigned long long)sh->sector, dd_idx);
-
- if ( dd_idx == qd_idx ) {
- /* We're actually computing the Q drive */
- compute_parity6(sh, UPDATE_PARITY);
- } else {
- dest = page_address(sh->dev[dd_idx].page);
- if (!nozero) memset(dest, 0, STRIPE_SIZE);
- count = 0;
- for (i = disks ; i--; ) {
- if (i == dd_idx || i == qd_idx)
- continue;
- p = page_address(sh->dev[i].page);
- if (test_bit(R5_UPTODATE, &sh->dev[i].flags))
- ptr[count++] = p;
- else
- printk("compute_block() %d, stripe %llu, %d"
- " not present\n", dd_idx,
- (unsigned long long)sh->sector, i);
-
- check_xor();
- }
- if (count)
- xor_blocks(count, STRIPE_SIZE, dest, ptr);
- if (!nozero) set_bit(R5_UPTODATE, &sh->dev[dd_idx].flags);
- else clear_bit(R5_UPTODATE, &sh->dev[dd_idx].flags);
- }
-}
-
-/* Compute two missing blocks */
-static void compute_block_2(struct stripe_head *sh, int dd_idx1, int dd_idx2)
-{
- int i, count, disks = sh->disks;
- int syndrome_disks = sh->ddf_layout ? disks : disks-2;
- int d0_idx = raid6_d0(sh);
- int faila = -1, failb = -1;
- /**** FIX THIS: This could be very bad if disks is close to 256 ****/
- void *ptrs[syndrome_disks+2];
-
- for (i = 0; i < disks ; i++)
- ptrs[i] = (void *)raid6_empty_zero_page;
- count = 0;
- i = d0_idx;
- do {
- int slot = raid6_idx_to_slot(i, sh, &count, syndrome_disks);
-
- ptrs[slot] = page_address(sh->dev[i].page);
-
- if (i == dd_idx1)
- faila = slot;
- if (i == dd_idx2)
- failb = slot;
- i = raid6_next_disk(i, disks);
- } while (i != d0_idx);
- BUG_ON(count != syndrome_disks);
-
- BUG_ON(faila == failb);
- if ( failb < faila ) { int tmp = faila; faila = failb; failb = tmp; }
-
- pr_debug("compute_block_2, stripe %llu, idx %d,%d (%d,%d)\n",
- (unsigned long long)sh->sector, dd_idx1, dd_idx2,
- faila, failb);
-
- if (failb == syndrome_disks+1) {
- /* Q disk is one of the missing disks */
- if (faila == syndrome_disks) {
- /* Missing P+Q, just recompute */
- compute_parity6(sh, UPDATE_PARITY);
- return;
- } else {
- /* We're missing D+Q; recompute D from P */
- compute_block_1(sh, ((dd_idx1 == sh->qd_idx) ?
- dd_idx2 : dd_idx1),
- 0);
- compute_parity6(sh, UPDATE_PARITY); /* Is this necessary? */
- return;
- }
- }
-
- /* We're missing D+P or D+D; */
- if (failb == syndrome_disks) {
- /* We're missing D+P. */
- raid6_datap_recov(syndrome_disks+2, STRIPE_SIZE, faila, ptrs);
- } else {
- /* We're missing D+D. */
- raid6_2data_recov(syndrome_disks+2, STRIPE_SIZE, faila, failb,
- ptrs);
- }
-
- /* Both the above update both missing blocks */
- set_bit(R5_UPTODATE, &sh->dev[dd_idx1].flags);
- set_bit(R5_UPTODATE, &sh->dev[dd_idx2].flags);
-}
-
static void
-schedule_reconstruction5(struct stripe_head *sh, struct stripe_head_state *s,
+schedule_reconstruction(struct stripe_head *sh, struct stripe_head_state *s,
int rcw, int expand)
{
int i, pd_idx = sh->pd_idx, disks = sh->disks;
+ raid5_conf_t *conf = sh->raid_conf;
+ int level = conf->level;
if (rcw) {
/* if we are not expanding this is a proper write request, and
} else
sh->reconstruct_state = reconstruct_state_run;
- set_bit(STRIPE_OP_POSTXOR, &s->ops_request);
+ set_bit(STRIPE_OP_RECONSTRUCT, &s->ops_request);
for (i = disks; i--; ) {
struct r5dev *dev = &sh->dev[i];
s->locked++;
}
}
- if (s->locked + 1 == disks)
+ if (s->locked + conf->max_degraded == disks)
if (!test_and_set_bit(STRIPE_FULL_WRITE, &sh->state))
- atomic_inc(&sh->raid_conf->pending_full_writes);
+ atomic_inc(&conf->pending_full_writes);
} else {
+ BUG_ON(level == 6);
BUG_ON(!(test_bit(R5_UPTODATE, &sh->dev[pd_idx].flags) ||
test_bit(R5_Wantcompute, &sh->dev[pd_idx].flags)));
sh->reconstruct_state = reconstruct_state_prexor_drain_run;
set_bit(STRIPE_OP_PREXOR, &s->ops_request);
set_bit(STRIPE_OP_BIODRAIN, &s->ops_request);
- set_bit(STRIPE_OP_POSTXOR, &s->ops_request);
+ set_bit(STRIPE_OP_RECONSTRUCT, &s->ops_request);
for (i = disks; i--; ) {
struct r5dev *dev = &sh->dev[i];
}
}
- /* keep the parity disk locked while asynchronous operations
+ /* keep the parity disk(s) locked while asynchronous operations
* are in flight
*/
set_bit(R5_LOCKED, &sh->dev[pd_idx].flags);
clear_bit(R5_UPTODATE, &sh->dev[pd_idx].flags);
s->locked++;
+ if (level == 6) {
+ int qd_idx = sh->qd_idx;
+ struct r5dev *dev = &sh->dev[qd_idx];
+
+ set_bit(R5_LOCKED, &dev->flags);
+ clear_bit(R5_UPTODATE, &dev->flags);
+ s->locked++;
+ }
+
pr_debug("%s: stripe %llu locked: %d ops_request: %lx\n",
__func__, (unsigned long long)sh->sector,
s->locked, s->ops_request);
static void end_reshape(raid5_conf_t *conf);
-static int page_is_zero(struct page *p)
-{
- char *a = page_address(p);
- return ((*(u32*)a) == 0 &&
- memcmp(a, a+4, STRIPE_SIZE-4)==0);
-}
-
static void stripe_set_idx(sector_t stripe, raid5_conf_t *conf, int previous,
struct stripe_head *sh)
{
set_bit(STRIPE_OP_COMPUTE_BLK, &s->ops_request);
set_bit(R5_Wantcompute, &dev->flags);
sh->ops.target = disk_idx;
+ sh->ops.target2 = -1;
s->req_compute = 1;
/* Careful: from this point on 'uptodate' is in the eye
- * of raid5_run_ops which services 'compute' operations
+ * of raid_run_ops which services 'compute' operations
* before writes. R5_Wantcompute flags a block that will
* be R5_UPTODATE by the time it is needed for a
* subsequent operation.
set_bit(STRIPE_HANDLE, &sh->state);
}
-static void handle_stripe_fill6(struct stripe_head *sh,
- struct stripe_head_state *s, struct r6_state *r6s,
- int disks)
+/* fetch_block6 - checks the given member device to see if its data needs
+ * to be read or computed to satisfy a request.
+ *
+ * Returns 1 when no more member devices need to be checked, otherwise returns
+ * 0 to tell the loop in handle_stripe_fill6 to continue
+ */
+static int fetch_block6(struct stripe_head *sh, struct stripe_head_state *s,
+ struct r6_state *r6s, int disk_idx, int disks)
{
- int i;
- for (i = disks; i--; ) {
- struct r5dev *dev = &sh->dev[i];
- if (!test_bit(R5_LOCKED, &dev->flags) &&
- !test_bit(R5_UPTODATE, &dev->flags) &&
- (dev->toread || (dev->towrite &&
- !test_bit(R5_OVERWRITE, &dev->flags)) ||
- s->syncing || s->expanding ||
- (s->failed >= 1 &&
- (sh->dev[r6s->failed_num[0]].toread ||
- s->to_write)) ||
- (s->failed >= 2 &&
- (sh->dev[r6s->failed_num[1]].toread ||
- s->to_write)))) {
- /* we would like to get this block, possibly
- * by computing it, but we might not be able to
+ struct r5dev *dev = &sh->dev[disk_idx];
+ struct r5dev *fdev[2] = { &sh->dev[r6s->failed_num[0]],
+ &sh->dev[r6s->failed_num[1]] };
+
+ if (!test_bit(R5_LOCKED, &dev->flags) &&
+ !test_bit(R5_UPTODATE, &dev->flags) &&
+ (dev->toread ||
+ (dev->towrite && !test_bit(R5_OVERWRITE, &dev->flags)) ||
+ s->syncing || s->expanding ||
+ (s->failed >= 1 &&
+ (fdev[0]->toread || s->to_write)) ||
+ (s->failed >= 2 &&
+ (fdev[1]->toread || s->to_write)))) {
+ /* we would like to get this block, possibly by computing it,
+ * otherwise read it if the backing disk is insync
+ */
+ BUG_ON(test_bit(R5_Wantcompute, &dev->flags));
+ BUG_ON(test_bit(R5_Wantread, &dev->flags));
+ if ((s->uptodate == disks - 1) &&
+ (s->failed && (disk_idx == r6s->failed_num[0] ||
+ disk_idx == r6s->failed_num[1]))) {
+ /* have disk failed, and we're requested to fetch it;
+ * do compute it
*/
- if ((s->uptodate == disks - 1) &&
- (s->failed && (i == r6s->failed_num[0] ||
- i == r6s->failed_num[1]))) {
- pr_debug("Computing stripe %llu block %d\n",
- (unsigned long long)sh->sector, i);
- compute_block_1(sh, i, 0);
- s->uptodate++;
- } else if ( s->uptodate == disks-2 && s->failed >= 2 ) {
- /* Computing 2-failure is *very* expensive; only
- * do it if failed >= 2
- */
- int other;
- for (other = disks; other--; ) {
- if (other == i)
- continue;
- if (!test_bit(R5_UPTODATE,
- &sh->dev[other].flags))
- break;
- }
- BUG_ON(other < 0);
- pr_debug("Computing stripe %llu blocks %d,%d\n",
- (unsigned long long)sh->sector,
- i, other);
- compute_block_2(sh, i, other);
- s->uptodate += 2;
- } else if (test_bit(R5_Insync, &dev->flags)) {
- set_bit(R5_LOCKED, &dev->flags);
- set_bit(R5_Wantread, &dev->flags);
- s->locked++;
- pr_debug("Reading block %d (sync=%d)\n",
- i, s->syncing);
+ pr_debug("Computing stripe %llu block %d\n",
+ (unsigned long long)sh->sector, disk_idx);
+ set_bit(STRIPE_COMPUTE_RUN, &sh->state);
+ set_bit(STRIPE_OP_COMPUTE_BLK, &s->ops_request);
+ set_bit(R5_Wantcompute, &dev->flags);
+ sh->ops.target = disk_idx;
+ sh->ops.target2 = -1; /* no 2nd target */
+ s->req_compute = 1;
+ s->uptodate++;
+ return 1;
+ } else if (s->uptodate == disks-2 && s->failed >= 2) {
+ /* Computing 2-failure is *very* expensive; only
+ * do it if failed >= 2
+ */
+ int other;
+ for (other = disks; other--; ) {
+ if (other == disk_idx)
+ continue;
+ if (!test_bit(R5_UPTODATE,
+ &sh->dev[other].flags))
+ break;
}
+ BUG_ON(other < 0);
+ pr_debug("Computing stripe %llu blocks %d,%d\n",
+ (unsigned long long)sh->sector,
+ disk_idx, other);
+ set_bit(STRIPE_COMPUTE_RUN, &sh->state);
+ set_bit(STRIPE_OP_COMPUTE_BLK, &s->ops_request);
+ set_bit(R5_Wantcompute, &sh->dev[disk_idx].flags);
+ set_bit(R5_Wantcompute, &sh->dev[other].flags);
+ sh->ops.target = disk_idx;
+ sh->ops.target2 = other;
+ s->uptodate += 2;
+ s->req_compute = 1;
+ return 1;
+ } else if (test_bit(R5_Insync, &dev->flags)) {
+ set_bit(R5_LOCKED, &dev->flags);
+ set_bit(R5_Wantread, &dev->flags);
+ s->locked++;
+ pr_debug("Reading block %d (sync=%d)\n",
+ disk_idx, s->syncing);
}
}
+
+ return 0;
+}
+
+/**
+ * handle_stripe_fill6 - read or compute data to satisfy pending requests.
+ */
+static void handle_stripe_fill6(struct stripe_head *sh,
+ struct stripe_head_state *s, struct r6_state *r6s,
+ int disks)
+{
+ int i;
+
+ /* look for blocks to read/compute, skip this if a compute
+ * is already in flight, or if the stripe contents are in the
+ * midst of changing due to a write
+ */
+ if (!test_bit(STRIPE_COMPUTE_RUN, &sh->state) && !sh->check_state &&
+ !sh->reconstruct_state)
+ for (i = disks; i--; )
+ if (fetch_block6(sh, s, r6s, i, disks))
+ break;
set_bit(STRIPE_HANDLE, &sh->state);
}
*/
/* since handle_stripe can be called at any time we need to handle the
* case where a compute block operation has been submitted and then a
- * subsequent call wants to start a write request. raid5_run_ops only
- * handles the case where compute block and postxor are requested
+ * subsequent call wants to start a write request. raid_run_ops only
+ * handles the case where compute block and reconstruct are requested
* simultaneously. If this is not the case then new writes need to be
* held off until the compute completes.
*/
if ((s->req_compute || !test_bit(STRIPE_COMPUTE_RUN, &sh->state)) &&
(s->locked == 0 && (rcw == 0 || rmw == 0) &&
!test_bit(STRIPE_BIT_DELAY, &sh->state)))
- schedule_reconstruction5(sh, s, rcw == 0, 0);
+ schedule_reconstruction(sh, s, rcw == 0, 0);
}
static void handle_stripe_dirtying6(raid5_conf_t *conf,
struct stripe_head *sh, struct stripe_head_state *s,
- struct r6_state *r6s, int disks)
-{
- int rcw = 0, must_compute = 0, pd_idx = sh->pd_idx, i;
- int qd_idx = sh->qd_idx;
- for (i = disks; i--; ) {
- struct r5dev *dev = &sh->dev[i];
- /* Would I have to read this buffer for reconstruct_write */
- if (!test_bit(R5_OVERWRITE, &dev->flags)
- && i != pd_idx && i != qd_idx
- && (!test_bit(R5_LOCKED, &dev->flags)
- ) &&
- !test_bit(R5_UPTODATE, &dev->flags)) {
- if (test_bit(R5_Insync, &dev->flags)) rcw++;
- else {
- pr_debug("raid6: must_compute: "
- "disk %d flags=%#lx\n", i, dev->flags);
- must_compute++;
- }
- }
- }
- pr_debug("for sector %llu, rcw=%d, must_compute=%d\n",
- (unsigned long long)sh->sector, rcw, must_compute);
- set_bit(STRIPE_HANDLE, &sh->state);
-
- if (rcw > 0)
- /* want reconstruct write, but need to get some data */
- for (i = disks; i--; ) {
- struct r5dev *dev = &sh->dev[i];
- if (!test_bit(R5_OVERWRITE, &dev->flags)
- && !(s->failed == 0 && (i == pd_idx || i == qd_idx))
- && !test_bit(R5_LOCKED, &dev->flags) &&
- !test_bit(R5_UPTODATE, &dev->flags) &&
- test_bit(R5_Insync, &dev->flags)) {
- if (
- test_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
- pr_debug("Read_old stripe %llu "
- "block %d for Reconstruct\n",
- (unsigned long long)sh->sector, i);
- set_bit(R5_LOCKED, &dev->flags);
- set_bit(R5_Wantread, &dev->flags);
- s->locked++;
- } else {
- pr_debug("Request delayed stripe %llu "
- "block %d for Reconstruct\n",
- (unsigned long long)sh->sector, i);
- set_bit(STRIPE_DELAYED, &sh->state);
- set_bit(STRIPE_HANDLE, &sh->state);
- }
+ struct r6_state *r6s, int disks)
+{
+ int rcw = 0, pd_idx = sh->pd_idx, i;
+ int qd_idx = sh->qd_idx;
+
+ set_bit(STRIPE_HANDLE, &sh->state);
+ for (i = disks; i--; ) {
+ struct r5dev *dev = &sh->dev[i];
+ /* check if we haven't enough data */
+ if (!test_bit(R5_OVERWRITE, &dev->flags) &&
+ i != pd_idx && i != qd_idx &&
+ !test_bit(R5_LOCKED, &dev->flags) &&
+ !(test_bit(R5_UPTODATE, &dev->flags) ||
+ test_bit(R5_Wantcompute, &dev->flags))) {
+ rcw++;
+ if (!test_bit(R5_Insync, &dev->flags))
+ continue; /* it's a failed drive */
+
+ if (
+ test_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
+ pr_debug("Read_old stripe %llu "
+ "block %d for Reconstruct\n",
+ (unsigned long long)sh->sector, i);
+ set_bit(R5_LOCKED, &dev->flags);
+ set_bit(R5_Wantread, &dev->flags);
+ s->locked++;
+ } else {
+ pr_debug("Request delayed stripe %llu "
+ "block %d for Reconstruct\n",
+ (unsigned long long)sh->sector, i);
+ set_bit(STRIPE_DELAYED, &sh->state);
+ set_bit(STRIPE_HANDLE, &sh->state);
}
}
+ }
/* now if nothing is locked, and if we have enough data, we can start a
* write request
*/
- if (s->locked == 0 && rcw == 0 &&
+ if ((s->req_compute || !test_bit(STRIPE_COMPUTE_RUN, &sh->state)) &&
+ s->locked == 0 && rcw == 0 &&
!test_bit(STRIPE_BIT_DELAY, &sh->state)) {
- if (must_compute > 0) {
- /* We have failed blocks and need to compute them */
- switch (s->failed) {
- case 0:
- BUG();
- case 1:
- compute_block_1(sh, r6s->failed_num[0], 0);
- break;
- case 2:
- compute_block_2(sh, r6s->failed_num[0],
- r6s->failed_num[1]);
- break;
- default: /* This request should have been failed? */
- BUG();
- }
- }
-
- pr_debug("Computing parity for stripe %llu\n",
- (unsigned long long)sh->sector);
- compute_parity6(sh, RECONSTRUCT_WRITE);
- /* now every locked buffer is ready to be written */
- for (i = disks; i--; )
- if (test_bit(R5_LOCKED, &sh->dev[i].flags)) {
- pr_debug("Writing stripe %llu block %d\n",
- (unsigned long long)sh->sector, i);
- s->locked++;
- set_bit(R5_Wantwrite, &sh->dev[i].flags);
- }
- if (s->locked == disks)
- if (!test_and_set_bit(STRIPE_FULL_WRITE, &sh->state))
- atomic_inc(&conf->pending_full_writes);
- /* after a RECONSTRUCT_WRITE, the stripe MUST be in-sync */
- set_bit(STRIPE_INSYNC, &sh->state);
-
- if (test_and_clear_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
- atomic_dec(&conf->preread_active_stripes);
- if (atomic_read(&conf->preread_active_stripes) <
- IO_THRESHOLD)
- md_wakeup_thread(conf->mddev->thread);
- }
+ schedule_reconstruction(sh, s, 1, 0);
}
}
* we are done. Otherwise update the mismatch count and repair
* parity if !MD_RECOVERY_CHECK
*/
- if (sh->ops.zero_sum_result == 0)
+ if ((sh->ops.zero_sum_result & SUM_CHECK_P_RESULT) == 0)
/* parity is correct (on disc,
* not in buffer any more)
*/
set_bit(R5_Wantcompute,
&sh->dev[sh->pd_idx].flags);
sh->ops.target = sh->pd_idx;
+ sh->ops.target2 = -1;
s->uptodate++;
}
}
static void handle_parity_checks6(raid5_conf_t *conf, struct stripe_head *sh,
- struct stripe_head_state *s,
- struct r6_state *r6s, struct page *tmp_page,
- int disks)
+ struct stripe_head_state *s,
+ struct r6_state *r6s, int disks)
{
- int update_p = 0, update_q = 0;
- struct r5dev *dev;
int pd_idx = sh->pd_idx;
int qd_idx = sh->qd_idx;
+ struct r5dev *dev;
set_bit(STRIPE_HANDLE, &sh->state);
BUG_ON(s->failed > 2);
- BUG_ON(s->uptodate < disks);
+
/* Want to check and possibly repair P and Q.
* However there could be one 'failed' device, in which
* case we can only check one of them, possibly using the
* other to generate missing data
*/
- /* If !tmp_page, we cannot do the calculations,
- * but as we have set STRIPE_HANDLE, we will soon be called
- * by stripe_handle with a tmp_page - just wait until then.
- */
- if (tmp_page) {
+ switch (sh->check_state) {
+ case check_state_idle:
+ /* start a new check operation if there are < 2 failures */
if (s->failed == r6s->q_failed) {
- /* The only possible failed device holds 'Q', so it
+ /* The only possible failed device holds Q, so it
* makes sense to check P (If anything else were failed,
* we would have used P to recreate it).
*/
- compute_block_1(sh, pd_idx, 1);
- if (!page_is_zero(sh->dev[pd_idx].page)) {
- compute_block_1(sh, pd_idx, 0);
- update_p = 1;
- }
+ sh->check_state = check_state_run;
}
if (!r6s->q_failed && s->failed < 2) {
- /* q is not failed, and we didn't use it to generate
+ /* Q is not failed, and we didn't use it to generate
* anything, so it makes sense to check it
*/
- memcpy(page_address(tmp_page),
- page_address(sh->dev[qd_idx].page),
- STRIPE_SIZE);
- compute_parity6(sh, UPDATE_PARITY);
- if (memcmp(page_address(tmp_page),
- page_address(sh->dev[qd_idx].page),
- STRIPE_SIZE) != 0) {
- clear_bit(STRIPE_INSYNC, &sh->state);
- update_q = 1;
- }
+ if (sh->check_state == check_state_run)
+ sh->check_state = check_state_run_pq;
+ else
+ sh->check_state = check_state_run_q;
}
- if (update_p || update_q) {
- conf->mddev->resync_mismatches += STRIPE_SECTORS;
- if (test_bit(MD_RECOVERY_CHECK, &conf->mddev->recovery))
- /* don't try to repair!! */
- update_p = update_q = 0;
+
+ /* discard potentially stale zero_sum_result */
+ sh->ops.zero_sum_result = 0;
+
+ if (sh->check_state == check_state_run) {
+ /* async_xor_zero_sum destroys the contents of P */
+ clear_bit(R5_UPTODATE, &sh->dev[pd_idx].flags);
+ s->uptodate--;
+ }
+ if (sh->check_state >= check_state_run &&
+ sh->check_state <= check_state_run_pq) {
+ /* async_syndrome_zero_sum preserves P and Q, so
+ * no need to mark them !uptodate here
+ */
+ set_bit(STRIPE_OP_CHECK, &s->ops_request);
+ break;
}
+ /* we have 2-disk failure */
+ BUG_ON(s->failed != 2);
+ /* fall through */
+ case check_state_compute_result:
+ sh->check_state = check_state_idle;
+
+ /* check that a write has not made the stripe insync */
+ if (test_bit(STRIPE_INSYNC, &sh->state))
+ break;
+
/* now write out any block on a failed drive,
- * or P or Q if they need it
+ * or P or Q if they were recomputed
*/
-
+ BUG_ON(s->uptodate < disks - 1); /* We don't need Q to recover */
if (s->failed == 2) {
dev = &sh->dev[r6s->failed_num[1]];
s->locked++;
set_bit(R5_LOCKED, &dev->flags);
set_bit(R5_Wantwrite, &dev->flags);
}
-
- if (update_p) {
+ if (sh->ops.zero_sum_result & SUM_CHECK_P_RESULT) {
dev = &sh->dev[pd_idx];
s->locked++;
set_bit(R5_LOCKED, &dev->flags);
set_bit(R5_Wantwrite, &dev->flags);
}
- if (update_q) {
+ if (sh->ops.zero_sum_result & SUM_CHECK_Q_RESULT) {
dev = &sh->dev[qd_idx];
s->locked++;
set_bit(R5_LOCKED, &dev->flags);
clear_bit(STRIPE_DEGRADED, &sh->state);
set_bit(STRIPE_INSYNC, &sh->state);
+ break;
+ case check_state_run:
+ case check_state_run_q:
+ case check_state_run_pq:
+ break; /* we will be called again upon completion */
+ case check_state_check_result:
+ sh->check_state = check_state_idle;
+
+ /* handle a successful check operation, if parity is correct
+ * we are done. Otherwise update the mismatch count and repair
+ * parity if !MD_RECOVERY_CHECK
+ */
+ if (sh->ops.zero_sum_result == 0) {
+ /* both parities are correct */
+ if (!s->failed)
+ set_bit(STRIPE_INSYNC, &sh->state);
+ else {
+ /* in contrast to the raid5 case we can validate
+ * parity, but still have a failure to write
+ * back
+ */
+ sh->check_state = check_state_compute_result;
+ /* Returning at this point means that we may go
+ * off and bring p and/or q uptodate again so
+ * we make sure to check zero_sum_result again
+ * to verify if p or q need writeback
+ */
+ }
+ } else {
+ conf->mddev->resync_mismatches += STRIPE_SECTORS;
+ if (test_bit(MD_RECOVERY_CHECK, &conf->mddev->recovery))
+ /* don't try to repair!! */
+ set_bit(STRIPE_INSYNC, &sh->state);
+ else {
+ int *target = &sh->ops.target;
+
+ sh->ops.target = -1;
+ sh->ops.target2 = -1;
+ sh->check_state = check_state_compute_run;
+ set_bit(STRIPE_COMPUTE_RUN, &sh->state);
+ set_bit(STRIPE_OP_COMPUTE_BLK, &s->ops_request);
+ if (sh->ops.zero_sum_result & SUM_CHECK_P_RESULT) {
+ set_bit(R5_Wantcompute,
+ &sh->dev[pd_idx].flags);
+ *target = pd_idx;
+ target = &sh->ops.target2;
+ s->uptodate++;
+ }
+ if (sh->ops.zero_sum_result & SUM_CHECK_Q_RESULT) {
+ set_bit(R5_Wantcompute,
+ &sh->dev[qd_idx].flags);
+ *target = qd_idx;
+ s->uptodate++;
+ }
+ }
+ }
+ break;
+ case check_state_compute_run:
+ break;
+ default:
+ printk(KERN_ERR "%s: unknown check_state: %d sector: %llu\n",
+ __func__, sh->check_state,
+ (unsigned long long) sh->sector);
+ BUG();
}
}
if (i != sh->pd_idx && i != sh->qd_idx) {
int dd_idx, j;
struct stripe_head *sh2;
+ struct async_submit_ctl submit;
sector_t bn = compute_blocknr(sh, i, 1);
sector_t s = raid5_compute_sector(conf, bn, 0,
}
/* place all the copies on one channel */
+ init_async_submit(&submit, 0, tx, NULL, NULL, NULL);
tx = async_memcpy(sh2->dev[dd_idx].page,
- sh->dev[i].page, 0, 0, STRIPE_SIZE,
- ASYNC_TX_DEP_ACK, tx, NULL, NULL);
+ sh->dev[i].page, 0, 0, STRIPE_SIZE,
+ &submit);
set_bit(R5_Expanded, &sh2->dev[dd_idx].flags);
set_bit(R5_UPTODATE, &sh2->dev[dd_idx].flags);
rcu_read_lock();
for (i=disks; i--; ) {
mdk_rdev_t *rdev;
- struct r5dev *dev = &sh->dev[i];
+
+ dev = &sh->dev[i];
clear_bit(R5_Insync, &dev->flags);
pr_debug("check %d: state 0x%lx toread %p read %p write %p "
/* Need to write out all blocks after computing parity */
sh->disks = conf->raid_disks;
stripe_set_idx(sh->sector, conf, 0, sh);
- schedule_reconstruction5(sh, &s, 1, 1);
+ schedule_reconstruction(sh, &s, 1, 1);
} else if (s.expanded && !sh->reconstruct_state && s.locked == 0) {
clear_bit(STRIPE_EXPAND_READY, &sh->state);
atomic_dec(&conf->reshape_stripes);
md_wait_for_blocked_rdev(blocked_rdev, conf->mddev);
if (s.ops_request)
- raid5_run_ops(sh, s.ops_request);
+ raid_run_ops(sh, s.ops_request);
ops_run_io(sh, &s);
return blocked_rdev == NULL;
}
-static bool handle_stripe6(struct stripe_head *sh, struct page *tmp_page)
+static bool handle_stripe6(struct stripe_head *sh)
{
raid5_conf_t *conf = sh->raid_conf;
int disks = sh->disks;
mdk_rdev_t *blocked_rdev = NULL;
pr_debug("handling stripe %llu, state=%#lx cnt=%d, "
- "pd_idx=%d, qd_idx=%d\n",
+ "pd_idx=%d, qd_idx=%d\n, check:%d, reconstruct:%d\n",
(unsigned long long)sh->sector, sh->state,
- atomic_read(&sh->count), pd_idx, qd_idx);
+ atomic_read(&sh->count), pd_idx, qd_idx,
+ sh->check_state, sh->reconstruct_state);
memset(&s, 0, sizeof(s));
spin_lock(&sh->lock);
pr_debug("check %d: state 0x%lx read %p write %p written %p\n",
i, dev->flags, dev->toread, dev->towrite, dev->written);
- /* maybe we can reply to a read */
- if (test_bit(R5_UPTODATE, &dev->flags) && dev->toread) {
- struct bio *rbi, *rbi2;
- pr_debug("Return read for disc %d\n", i);
- spin_lock_irq(&conf->device_lock);
- rbi = dev->toread;
- dev->toread = NULL;
- if (test_and_clear_bit(R5_Overlap, &dev->flags))
- wake_up(&conf->wait_for_overlap);
- spin_unlock_irq(&conf->device_lock);
- while (rbi && rbi->bi_sector < dev->sector + STRIPE_SECTORS) {
- copy_data(0, rbi, dev->page, dev->sector);
- rbi2 = r5_next_bio(rbi, dev->sector);
- spin_lock_irq(&conf->device_lock);
- if (!raid5_dec_bi_phys_segments(rbi)) {
- rbi->bi_next = return_bi;
- return_bi = rbi;
- }
- spin_unlock_irq(&conf->device_lock);
- rbi = rbi2;
- }
- }
+ /* maybe we can reply to a read
+ *
+ * new wantfill requests are only permitted while
+ * ops_complete_biofill is guaranteed to be inactive
+ */
+ if (test_bit(R5_UPTODATE, &dev->flags) && dev->toread &&
+ !test_bit(STRIPE_BIOFILL_RUN, &sh->state))
+ set_bit(R5_Wantfill, &dev->flags);
/* now count some things */
if (test_bit(R5_LOCKED, &dev->flags)) s.locked++;
if (test_bit(R5_UPTODATE, &dev->flags)) s.uptodate++;
+ if (test_bit(R5_Wantcompute, &dev->flags)) {
+ s.compute++;
+ BUG_ON(s.compute > 2);
+ }
-
- if (dev->toread)
+ if (test_bit(R5_Wantfill, &dev->flags)) {
+ s.to_fill++;
+ } else if (dev->toread)
s.to_read++;
if (dev->towrite) {
s.to_write++;
blocked_rdev = NULL;
}
+ if (s.to_fill && !test_bit(STRIPE_BIOFILL_RUN, &sh->state)) {
+ set_bit(STRIPE_OP_BIOFILL, &s.ops_request);
+ set_bit(STRIPE_BIOFILL_RUN, &sh->state);
+ }
+
pr_debug("locked=%d uptodate=%d to_read=%d"
" to_write=%d failed=%d failed_num=%d,%d\n",
s.locked, s.uptodate, s.to_read, s.to_write, s.failed,
* or to load a block that is being partially written.
*/
if (s.to_read || s.non_overwrite || (s.to_write && s.failed) ||
- (s.syncing && (s.uptodate < disks)) || s.expanding)
+ (s.syncing && (s.uptodate + s.compute < disks)) || s.expanding)
handle_stripe_fill6(sh, &s, &r6s, disks);
- /* now to consider writing and what else, if anything should be read */
- if (s.to_write)
+ /* Now we check to see if any write operations have recently
+ * completed
+ */
+ if (sh->reconstruct_state == reconstruct_state_drain_result) {
+ int qd_idx = sh->qd_idx;
+
+ sh->reconstruct_state = reconstruct_state_idle;
+ /* All the 'written' buffers and the parity blocks are ready to
+ * be written back to disk
+ */
+ BUG_ON(!test_bit(R5_UPTODATE, &sh->dev[sh->pd_idx].flags));
+ BUG_ON(!test_bit(R5_UPTODATE, &sh->dev[qd_idx].flags));
+ for (i = disks; i--; ) {
+ dev = &sh->dev[i];
+ if (test_bit(R5_LOCKED, &dev->flags) &&
+ (i == sh->pd_idx || i == qd_idx ||
+ dev->written)) {
+ pr_debug("Writing block %d\n", i);
+ BUG_ON(!test_bit(R5_UPTODATE, &dev->flags));
+ set_bit(R5_Wantwrite, &dev->flags);
+ if (!test_bit(R5_Insync, &dev->flags) ||
+ ((i == sh->pd_idx || i == qd_idx) &&
+ s.failed == 0))
+ set_bit(STRIPE_INSYNC, &sh->state);
+ }
+ }
+ if (test_and_clear_bit(STRIPE_PREREAD_ACTIVE, &sh->state)) {
+ atomic_dec(&conf->preread_active_stripes);
+ if (atomic_read(&conf->preread_active_stripes) <
+ IO_THRESHOLD)
+ md_wakeup_thread(conf->mddev->thread);
+ }
+ }
+
+ /* Now to consider new write requests and what else, if anything
+ * should be read. We do not handle new writes when:
+ * 1/ A 'write' operation (copy+gen_syndrome) is already in flight.
+ * 2/ A 'check' operation is in flight, as it may clobber the parity
+ * block.
+ */
+ if (s.to_write && !sh->reconstruct_state && !sh->check_state)
handle_stripe_dirtying6(conf, sh, &s, &r6s, disks);
/* maybe we need to check and possibly fix the parity for this stripe
* Any reads will already have been scheduled, so we just see if enough
- * data is available
+ * data is available. The parity check is held off while parity
+ * dependent operations are in flight.
*/
- if (s.syncing && s.locked == 0 && !test_bit(STRIPE_INSYNC, &sh->state))
- handle_parity_checks6(conf, sh, &s, &r6s, tmp_page, disks);
+ if (sh->check_state ||
+ (s.syncing && s.locked == 0 &&
+ !test_bit(STRIPE_COMPUTE_RUN, &sh->state) &&
+ !test_bit(STRIPE_INSYNC, &sh->state)))
+ handle_parity_checks6(conf, sh, &s, &r6s, disks);
if (s.syncing && s.locked == 0 && test_bit(STRIPE_INSYNC, &sh->state)) {
md_done_sync(conf->mddev, STRIPE_SECTORS,1);
set_bit(R5_Wantwrite, &dev->flags);
set_bit(R5_ReWrite, &dev->flags);
set_bit(R5_LOCKED, &dev->flags);
+ s.locked++;
} else {
/* let's read it back */
set_bit(R5_Wantread, &dev->flags);
set_bit(R5_LOCKED, &dev->flags);
+ s.locked++;
}
}
}
- if (s.expanded && test_bit(STRIPE_EXPANDING, &sh->state)) {
+ /* Finish reconstruct operations initiated by the expansion process */
+ if (sh->reconstruct_state == reconstruct_state_result) {
+ sh->reconstruct_state = reconstruct_state_idle;
+ clear_bit(STRIPE_EXPANDING, &sh->state);
+ for (i = conf->raid_disks; i--; ) {
+ set_bit(R5_Wantwrite, &sh->dev[i].flags);
+ set_bit(R5_LOCKED, &sh->dev[i].flags);
+ s.locked++;
+ }
+ }
+
+ if (s.expanded && test_bit(STRIPE_EXPANDING, &sh->state) &&
+ !sh->reconstruct_state) {
struct stripe_head *sh2
= get_active_stripe(conf, sh->sector, 1, 1, 1);
if (sh2 && test_bit(STRIPE_EXPAND_SOURCE, &sh2->state)) {
/* Need to write out all blocks after computing P&Q */
sh->disks = conf->raid_disks;
stripe_set_idx(sh->sector, conf, 0, sh);
- compute_parity6(sh, RECONSTRUCT_WRITE);
- for (i = conf->raid_disks ; i-- ; ) {
- set_bit(R5_LOCKED, &sh->dev[i].flags);
- s.locked++;
- set_bit(R5_Wantwrite, &sh->dev[i].flags);
- }
- clear_bit(STRIPE_EXPANDING, &sh->state);
- } else if (s.expanded) {
+ schedule_reconstruction(sh, &s, 1, 1);
+ } else if (s.expanded && !sh->reconstruct_state && s.locked == 0) {
clear_bit(STRIPE_EXPAND_READY, &sh->state);
atomic_dec(&conf->reshape_stripes);
wake_up(&conf->wait_for_overlap);
if (unlikely(blocked_rdev))
md_wait_for_blocked_rdev(blocked_rdev, conf->mddev);
+ if (s.ops_request)
+ raid_run_ops(sh, s.ops_request);
+
ops_run_io(sh, &s);
return_io(return_bi);
}
/* returns true if the stripe was handled */
-static bool handle_stripe(struct stripe_head *sh, struct page *tmp_page)
+static bool handle_stripe(struct stripe_head *sh)
{
if (sh->raid_conf->level == 6)
- return handle_stripe6(sh, tmp_page);
+ return handle_stripe6(sh);
else
return handle_stripe5(sh);
}
-
-
static void raid5_activate_delayed(raid5_conf_t *conf)
{
if (atomic_read(&conf->preread_active_stripes) < IO_THRESHOLD) {
/* No difference between reads and writes. Just check
* how busy the stripe_cache is
*/
+
+ if (mddev_congested(mddev, bits))
+ return 1;
if (conf->inactive_blocked)
return 1;
if (conf->quiesce)
INIT_LIST_HEAD(&stripes);
for (i = 0; i < reshape_sectors; i += STRIPE_SECTORS) {
int j;
- int skipped = 0;
+ int skipped_disk = 0;
sh = get_active_stripe(conf, stripe_addr+i, 0, 0, 1);
set_bit(STRIPE_EXPANDING, &sh->state);
atomic_inc(&conf->reshape_stripes);
continue;
s = compute_blocknr(sh, j, 0);
if (s < raid5_size(mddev, 0, 0)) {
- skipped = 1;
+ skipped_disk = 1;
continue;
}
memset(page_address(sh->dev[j].page), 0, STRIPE_SIZE);
set_bit(R5_Expanded, &sh->dev[j].flags);
set_bit(R5_UPTODATE, &sh->dev[j].flags);
}
- if (!skipped) {
+ if (!skipped_disk) {
set_bit(STRIPE_EXPAND_READY, &sh->state);
set_bit(STRIPE_HANDLE, &sh->state);
}
spin_unlock(&sh->lock);
/* wait for any blocked device to be handled */
- while(unlikely(!handle_stripe(sh, NULL)))
+ while (unlikely(!handle_stripe(sh)))
;
release_stripe(sh);
return handled;
}
- handle_stripe(sh, NULL);
+ handle_stripe(sh);
release_stripe(sh);
handled++;
}
return handled;
}
+#ifdef CONFIG_MULTICORE_RAID456
+static void __process_stripe(void *param, async_cookie_t cookie)
+{
+ struct stripe_head *sh = param;
+
+ handle_stripe(sh);
+ release_stripe(sh);
+}
+
+static void process_stripe(struct stripe_head *sh, struct list_head *domain)
+{
+ async_schedule_domain(__process_stripe, sh, domain);
+}
+
+static void synchronize_stripe_processing(struct list_head *domain)
+{
+ async_synchronize_full_domain(domain);
+}
+#else
+static void process_stripe(struct stripe_head *sh, struct list_head *domain)
+{
+ handle_stripe(sh);
+ release_stripe(sh);
+ cond_resched();
+}
+
+static void synchronize_stripe_processing(struct list_head *domain)
+{
+}
+#endif
/*
struct stripe_head *sh;
raid5_conf_t *conf = mddev->private;
int handled;
+ LIST_HEAD(raid_domain);
pr_debug("+++ raid5d active\n");
spin_unlock_irq(&conf->device_lock);
handled++;
- handle_stripe(sh, conf->spare_page);
- release_stripe(sh);
+ process_stripe(sh, &raid_domain);
spin_lock_irq(&conf->device_lock);
}
spin_unlock_irq(&conf->device_lock);
+ synchronize_stripe_processing(&raid_domain);
async_tx_issue_pending_all();
unplug_slaves(mddev);
return sectors * (raid_disks - conf->max_degraded);
}
+static void raid5_free_percpu(raid5_conf_t *conf)
+{
+ struct raid5_percpu *percpu;
+ unsigned long cpu;
+
+ if (!conf->percpu)
+ return;
+
+ get_online_cpus();
+ for_each_possible_cpu(cpu) {
+ percpu = per_cpu_ptr(conf->percpu, cpu);
+ safe_put_page(percpu->spare_page);
+ kfree(percpu->scribble);
+ }
+#ifdef CONFIG_HOTPLUG_CPU
+ unregister_cpu_notifier(&conf->cpu_notify);
+#endif
+ put_online_cpus();
+
+ free_percpu(conf->percpu);
+}
+
static void free_conf(raid5_conf_t *conf)
{
shrink_stripes(conf);
- safe_put_page(conf->spare_page);
+ raid5_free_percpu(conf);
kfree(conf->disks);
kfree(conf->stripe_hashtbl);
kfree(conf);
}
+#ifdef CONFIG_HOTPLUG_CPU
+static int raid456_cpu_notify(struct notifier_block *nfb, unsigned long action,
+ void *hcpu)
+{
+ raid5_conf_t *conf = container_of(nfb, raid5_conf_t, cpu_notify);
+ long cpu = (long)hcpu;
+ struct raid5_percpu *percpu = per_cpu_ptr(conf->percpu, cpu);
+
+ switch (action) {
+ case CPU_UP_PREPARE:
+ case CPU_UP_PREPARE_FROZEN:
+ if (conf->level == 6 && !percpu->spare_page)
+ percpu->spare_page = alloc_page(GFP_KERNEL);
+ if (!percpu->scribble)
+ percpu->scribble = kmalloc(conf->scribble_len, GFP_KERNEL);
+
+ if (!percpu->scribble ||
+ (conf->level == 6 && !percpu->spare_page)) {
+ safe_put_page(percpu->spare_page);
+ kfree(percpu->scribble);
+ pr_err("%s: failed memory allocation for cpu%ld\n",
+ __func__, cpu);
+ return NOTIFY_BAD;
+ }
+ break;
+ case CPU_DEAD:
+ case CPU_DEAD_FROZEN:
+ safe_put_page(percpu->spare_page);
+ kfree(percpu->scribble);
+ percpu->spare_page = NULL;
+ percpu->scribble = NULL;
+ break;
+ default:
+ break;
+ }
+ return NOTIFY_OK;
+}
+#endif
+
+static int raid5_alloc_percpu(raid5_conf_t *conf)
+{
+ unsigned long cpu;
+ struct page *spare_page;
+ struct raid5_percpu *allcpus;
+ void *scribble;
+ int err;
+
+ allcpus = alloc_percpu(struct raid5_percpu);
+ if (!allcpus)
+ return -ENOMEM;
+ conf->percpu = allcpus;
+
+ get_online_cpus();
+ err = 0;
+ for_each_present_cpu(cpu) {
+ if (conf->level == 6) {
+ spare_page = alloc_page(GFP_KERNEL);
+ if (!spare_page) {
+ err = -ENOMEM;
+ break;
+ }
+ per_cpu_ptr(conf->percpu, cpu)->spare_page = spare_page;
+ }
+ scribble = kmalloc(scribble_len(conf->raid_disks), GFP_KERNEL);
+ if (!scribble) {
+ err = -ENOMEM;
+ break;
+ }
+ per_cpu_ptr(conf->percpu, cpu)->scribble = scribble;
+ }
+#ifdef CONFIG_HOTPLUG_CPU
+ conf->cpu_notify.notifier_call = raid456_cpu_notify;
+ conf->cpu_notify.priority = 0;
+ if (err == 0)
+ err = register_cpu_notifier(&conf->cpu_notify);
+#endif
+ put_online_cpus();
+
+ return err;
+}
+
static raid5_conf_t *setup_conf(mddev_t *mddev)
{
raid5_conf_t *conf;
goto abort;
conf->raid_disks = mddev->raid_disks;
+ conf->scribble_len = scribble_len(conf->raid_disks);
if (mddev->reshape_position == MaxSector)
conf->previous_raid_disks = mddev->raid_disks;
else
if ((conf->stripe_hashtbl = kzalloc(PAGE_SIZE, GFP_KERNEL)) == NULL)
goto abort;
- if (mddev->new_level == 6) {
- conf->spare_page = alloc_page(GFP_KERNEL);
- if (!conf->spare_page)
- goto abort;
- }
+ conf->level = mddev->new_level;
+ if (raid5_alloc_percpu(conf) != 0)
+ goto abort;
+
spin_lock_init(&conf->device_lock);
init_waitqueue_head(&conf->wait_for_stripe);
init_waitqueue_head(&conf->wait_for_overlap);
printk(KERN_INFO "raid5: allocated %dkB for %s\n",
memory, mdname(mddev));
- conf->thread = md_register_thread(raid5d, mddev, "%s_raid5");
+ conf->thread = md_register_thread(raid5d, mddev, NULL);
if (!conf->thread) {
printk(KERN_ERR
"raid5: couldn't allocate thread for %s\n",
set_bit(MD_RECOVERY_RESHAPE, &mddev->recovery);
set_bit(MD_RECOVERY_RUNNING, &mddev->recovery);
mddev->sync_thread = md_register_thread(md_do_sync, mddev,
- "%s_reshape");
+ "reshape");
}
/* read-ahead size must cover two whole stripes, which is
set_bit(MD_RECOVERY_RESHAPE, &mddev->recovery);
set_bit(MD_RECOVERY_RUNNING, &mddev->recovery);
mddev->sync_thread = md_register_thread(md_do_sync, mddev,
- "%s_reshape");
+ "reshape");
if (!mddev->sync_thread) {
mddev->recovery = 0;
spin_lock_irq(&conf->device_lock);
#define _RAID5_H
#include <linux/raid/xor.h>
+#include <linux/dmaengine.h>
/*
*
*/
enum check_states {
check_state_idle = 0,
- check_state_run, /* parity check */
+ check_state_run, /* xor parity check */
+ check_state_run_q, /* q-parity check */
+ check_state_run_pq, /* pq dual parity check */
check_state_check_result,
check_state_compute_run, /* parity repair */
check_state_compute_result,
* @target - STRIPE_OP_COMPUTE_BLK target
*/
struct stripe_operations {
- int target;
- u32 zero_sum_result;
+ int target, target2;
+ enum sum_check_flags zero_sum_result;
} ops;
struct r5dev {
struct bio req;
#define STRIPE_OP_COMPUTE_BLK 1
#define STRIPE_OP_PREXOR 2
#define STRIPE_OP_BIODRAIN 3
-#define STRIPE_OP_POSTXOR 4
+#define STRIPE_OP_RECONSTRUCT 4
#define STRIPE_OP_CHECK 5
/*
* (fresh device added).
* Cleared when a sync completes.
*/
-
- struct page *spare_page; /* Used when checking P/Q in raid6 */
+ /* per cpu variables */
+ struct raid5_percpu {
+ struct page *spare_page; /* Used when checking P/Q in raid6 */
+ void *scribble; /* space for constructing buffer
+ * lists and performing address
+ * conversions
+ */
+ } *percpu;
+ size_t scribble_len; /* size of scribble region must be
+ * associated with conf to handle
+ * cpu hotplug while reshaping
+ */
+#ifdef CONFIG_HOTPLUG_CPU
+ struct notifier_block cpu_notify;
+#endif
/*
* Free stripes pool
*
*/
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/slab.h>
#include <linux/vmalloc.h>
return mask;
}
-static struct file_operations dvb_dvr_fops = {
+static const struct file_operations dvb_dvr_fops = {
.owner = THIS_MODULE,
.read = dvb_dvr_read,
.write = dvb_dvr_write,
*
*/
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/slab.h>
#include <linux/vmalloc.h>
#define DVB_MAJOR 212
#if defined(CONFIG_DVB_MAX_ADAPTERS) && CONFIG_DVB_MAX_ADAPTERS > 0
-#define DVB_MAX_ADAPTERS CONFIG_DVB_MAX_ADAPTERS
+ #define DVB_MAX_ADAPTERS CONFIG_DVB_MAX_ADAPTERS
#else
-#warning invalid CONFIG_DVB_MAX_ADAPTERS value
-#define DVB_MAX_ADAPTERS 8
+ #define DVB_MAX_ADAPTERS 8
#endif
#define DVB_UNSET (-1)
select DVB_DIB3000MC if !DVB_FE_CUSTOMISE
select DVB_S5H1411 if !DVB_FE_CUSTOMISE
select DVB_LGDT3305 if !DVB_FE_CUSTOMISE
- select DVB_TUNER_DIB0070 if !DVB_FE_CUSTOMISE
+ select DVB_TUNER_DIB0070
select MEDIA_TUNER_MT2060 if !MEDIA_TUNER_CUSTOMISE
select MEDIA_TUNER_MT2266 if !MEDIA_TUNER_CUSTOMISE
select MEDIA_TUNER_XC2028 if !MEDIA_TUNER_CUSTOMISE
return POLLIN;
}
-static struct file_operations fdtv_ca_fops = {
+static const struct file_operations fdtv_ca_fops = {
.owner = THIS_MODULE,
.ioctl = dvb_generic_ioctl,
.open = dvb_generic_open,
#include <linux/videodev2.h> /* V4L2 API defs */
#include <linux/param.h>
#include <linux/pnp.h>
+#include <linux/sched.h>
#include <linux/io.h> /* outb, outb_p */
#include <media/v4l2-device.h>
#include <media/v4l2-ioctl.h>
mutex_unlock(&sbuf->cam->s_mutex);
}
-static struct vm_operations_struct cafe_v4l_vm_ops = {
+static const struct vm_operations_struct cafe_v4l_vm_ops = {
.open = cafe_v4l_vm_open,
.close = cafe_v4l_vm_close
};
#include <linux/init.h>
#include <linux/fs.h>
#include <linux/vmalloc.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/proc_fs.h>
#include <linux/ctype.h>
}
-static struct vm_operations_struct et61x251_vm_ops = {
+static const struct vm_operations_struct et61x251_vm_ops = {
.open = et61x251_vm_open,
.close = et61x251_vm_close,
};
frame->v4l2_buf.flags &= ~V4L2_BUF_FLAG_MAPPED;
}
-static struct vm_operations_struct gspca_vm_ops = {
+static const struct vm_operations_struct gspca_vm_ops = {
.open = gspca_vm_open,
.close = gspca_vm_close,
};
meye.vma_use_count[idx]--;
}
-static struct vm_operations_struct meye_vm_ops = {
+static const struct vm_operations_struct meye_vm_ops = {
.open = meye_vm_open,
.close = meye_vm_close,
};
goto out;
}
- if (debug & DBGLVL_API)
+ if (saa_debug & DBGLVL_API)
saa7164_dumphex16(dev, buf, (buflen/16)*16);
saa7164_api_dump_subdevs(dev, buf, buflen);
dprintk(DBGLVL_API, "%s() len = %d bytes\n", __func__, len);
- if (debug & DBGLVL_I2C)
+ if (saa_debug & DBGLVL_I2C)
saa7164_dumphex16(dev, buf, 2 * 16);
ret = saa7164_cmd_send(bus->dev, unitid, GET_CUR,
if (ret != SAA_OK)
printk(KERN_ERR "%s() error, ret(2) = 0x%x\n", __func__, ret);
else {
- if (debug & DBGLVL_I2C)
+ if (saa_debug & DBGLVL_I2C)
saa7164_dumphex16(dev, buf, sizeof(buf));
memcpy(data, (buf + 2 * sizeof(u32) + reglen), datalen);
}
*((u32 *)(buf + 1 * sizeof(u32))) = datalen - reglen;
memcpy((buf + 2 * sizeof(u32)), data, datalen);
- if (debug & DBGLVL_I2C)
+ if (saa_debug & DBGLVL_I2C)
saa7164_dumphex16(dev, buf, sizeof(buf));
ret = saa7164_cmd_send(bus->dev, unitid, SET_CUR,
unsigned long stamp;
int r;
- if (debug >= 4)
+ if (saa_debug >= 4)
saa7164_bus_dump(dev);
dprintk(DBGLVL_CMD, "%s(seqno=%d)\n", __func__, seqno);
32 bus
*/
-unsigned int debug;
-module_param(debug, int, 0644);
+unsigned int saa_debug;
+module_param_named(debug, saa_debug, int, 0644);
MODULE_PARM_DESC(debug, "enable debug messages");
unsigned int waitsecs = 10;
printk(KERN_ERR "%s() Unsupported board detected, "
"registering without firmware\n", __func__);
- dprintk(1, "%s() parameter debug = %d\n", __func__, debug);
+ dprintk(1, "%s() parameter debug = %d\n", __func__, saa_debug);
dprintk(1, "%s() parameter waitsecs = %d\n", __func__, waitsecs);
fail_fw:
/* ----------------------------------------------------------- */
-extern unsigned int debug;
+extern unsigned int saa_debug;
#define dprintk(level, fmt, arg...)\
- do { if (debug & level)\
+ do { if (saa_debug & level)\
printk(KERN_DEBUG "%s: " fmt, dev->name, ## arg);\
} while (0)
"SuperH Mobile CEU driver attached to camera %d\n",
icd->devnum);
- clk_enable(pcdev->clk);
+ pm_runtime_get_sync(ici->v4l2_dev.dev);
ceu_write(pcdev, CAPSR, 1 << 16); /* reset */
while (ceu_read(pcdev, CSTSR) & 1)
}
spin_unlock_irqrestore(&pcdev->lock, flags);
- clk_disable(pcdev->clk);
+ pm_runtime_put_sync(ici->v4l2_dev.dev);
dev_info(icd->dev.parent,
"SuperH Mobile CEU driver detached from camera %d\n",
}
-static struct vm_operations_struct sn9c102_vm_ops = {
+static const struct vm_operations_struct sn9c102_vm_ops = {
.open = sn9c102_vm_open,
.close = sn9c102_vm_close,
};
if (sbuf->mapcount == 0)
sbuf->v4lbuf.flags &= ~V4L2_BUF_FLAG_MAPPED;
}
-static struct vm_operations_struct stk_v4l_vm_ops = {
+static const struct vm_operations_struct stk_v4l_vm_ops = {
.open = stk_v4l_vm_open,
.close = stk_v4l_vm_close
};
buffer->vma_use_count--;
}
-static struct vm_operations_struct uvc_vm_ops = {
+static const struct vm_operations_struct uvc_vm_ops = {
.open = uvc_vm_open,
.close = uvc_vm_close,
};
}
}
-static struct vm_operations_struct videobuf_vm_ops = {
+static const struct vm_operations_struct videobuf_vm_ops = {
.open = videobuf_vm_open,
.close = videobuf_vm_close,
};
return 0;
}
-static struct vm_operations_struct videobuf_vm_ops =
+static const struct vm_operations_struct videobuf_vm_ops =
{
.open = videobuf_vm_open,
.close = videobuf_vm_close,
return;
}
-static struct vm_operations_struct videobuf_vm_ops =
+static const struct vm_operations_struct videobuf_vm_ops =
{
.open = videobuf_vm_open,
.close = videobuf_vm_close,
dprintk("vino_vm_close(): count = %d\n", fb->map_count);
}
-static struct vm_operations_struct vino_vm_ops = {
+static const struct vm_operations_struct vino_vm_ops = {
.open = vino_vm_open,
.close = vino_vm_close,
};
}
-static struct vm_operations_struct zc0301_vm_ops = {
+static const struct vm_operations_struct zc0301_vm_ops = {
.open = zc0301_vm_open,
.close = zc0301_vm_close,
};
mutex_unlock(&zr->resource_lock);
}
-static struct vm_operations_struct zoran_vm_ops = {
+static const struct vm_operations_struct zoran_vm_ops = {
.open = zoran_vm_open,
.close = zoran_vm_close,
};
card->id.type = id_reg.type;
card->id.category = id_reg.category;
card->id.class = id_reg.class;
+ dev_dbg(&card->dev, "if_mode = %02x\n", id_reg.if_mode);
}
complete(&card->mrq_complete);
- dev_dbg(&card->dev, "if_mode = %02x\n", id_reg.if_mode);
return -EAGAIN;
}
}
* The AB3100 is usually assigned address 0x48 (7-bit)
* The chip is defined in the platform i2c_board_data section.
*/
-static unsigned short normal_i2c[] = { 0x48, I2C_CLIENT_END };
-I2C_CLIENT_INSMOD_1(ab3100);
u8 ab3100_get_chip_type(struct ab3100 *ab3100)
{
}
static const struct i2c_device_id ab3100_id[] = {
- { "ab3100", ab3100 },
+ { "ab3100", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, ab3100_id);
*/
#include <linux/module.h>
+#include <linux/sched.h>
#include <linux/ucb1400.h>
unsigned int ucb1400_adc_read(struct snd_ac97 *ac97, u16 adc_channel,
#include <linux/i2c.h>
#include <linux/mutex.h>
-/* Do not scan - the MAX6875 access method will write to some EEPROM chips */
-static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/* Insmod parameters */
-I2C_CLIENT_INSMOD_1(max6875);
-
/* The MAX6875 can only read/write 16 bytes at a time */
#define SLICE_SIZE 16
#define SLICE_BITS 4
.read = max6875_read,
};
-/* Return 0 if detection is successful, -ENODEV otherwise */
-static int max6875_detect(struct i2c_client *client, int kind,
- struct i2c_board_info *info)
+static int max6875_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
{
struct i2c_adapter *adapter = client->adapter;
+ struct max6875_data *data;
+ int err;
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WRITE_BYTE_DATA
| I2C_FUNC_SMBUS_READ_BYTE))
return -ENODEV;
- /* Only check even addresses */
+ /* Only bind to even addresses */
if (client->addr & 1)
return -ENODEV;
- strlcpy(info->type, "max6875", I2C_NAME_SIZE);
-
- return 0;
-}
-
-static int max6875_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
-{
- struct max6875_data *data;
- int err;
-
if (!(data = kzalloc(sizeof(struct max6875_data), GFP_KERNEL)))
return -ENOMEM;
.probe = max6875_probe,
.remove = max6875_remove,
.id_table = max6875_id,
-
- .detect = max6875_detect,
- .address_data = &addr_data,
};
static int __init max6875_init(void)
return mask;
}
-static struct file_operations phantom_file_ops = {
+static const struct file_operations phantom_file_ops = {
.open = phantom_open,
.release = phantom_release,
.unlocked_ioctl = phantom_ioctl,
/* Guaranteed user available resources on each node */
static int max_user_cbrs, max_user_dsr_bytes;
-static struct file_operations gru_fops;
static struct miscdevice gru_miscdev;
gru_proc_exit();
}
-static struct file_operations gru_fops = {
+static const struct file_operations gru_fops = {
.owner = THIS_MODULE,
.unlocked_ioctl = gru_file_unlocked_ioctl,
.mmap = gru_file_mmap,
.fops = &gru_fops,
};
-struct vm_operations_struct gru_vm_ops = {
+const struct vm_operations_struct gru_vm_ops = {
.close = gru_vma_close,
.fault = gru_fault,
};
/* Need 1K cacheline aligned that does not cross page boundary */
p = kmalloc(4096, 0);
+ if (p == NULL)
+ return -ENOMEM;
mq = ALIGNUP(p, 1024);
memset(mes, 0xee, sizeof(mes));
dw = mq;
static int create_proc_file(struct proc_entry *p)
{
- p->entry = create_proc_entry(p->name, p->mode, proc_gru);
+ p->entry = proc_create(p->name, p->mode, proc_gru, p->fops);
if (!p->entry)
return -1;
- p->entry->proc_fops = p->fops;
return 0;
}
*/
struct gru_unload_context_req;
-extern struct vm_operations_struct gru_vm_ops;
+extern const struct vm_operations_struct gru_vm_ops;
extern struct device *grudev;
extern struct gru_vma_data *gru_alloc_vma_data(struct vm_area_struct *vma,
return 0;
}
-static struct file_operations mmc_dbg_ext_csd_fops = {
+static const struct file_operations mmc_dbg_ext_csd_fops = {
.open = mmc_ext_csd_open,
.read = mmc_ext_csd_read,
.release = mmc_ext_csd_release,
static const unsigned int speed_unit[8] =
{ 10000, 100000, 1000000, 10000000, 0, 0, 0, 0 };
+/* FUNCE tuples with these types get passed to SDIO drivers */
+static const unsigned char funce_type_whitelist[] = {
+ 4 /* CISTPL_FUNCE_LAN_NODE_ID used in Broadcom cards */
+};
+
+static int cistpl_funce_whitelisted(unsigned char type)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(funce_type_whitelist); i++) {
+ if (funce_type_whitelist[i] == type)
+ return 1;
+ }
+ return 0;
+}
+
static int cistpl_funce_common(struct mmc_card *card,
const unsigned char *buf, unsigned size)
{
unsigned vsn;
unsigned min_size;
+ /* let SDIO drivers take care of whitelisted FUNCE tuples */
+ if (cistpl_funce_whitelisted(buf[0]))
+ return -EILSEQ;
+
vsn = func->card->cccr.sdio_vsn;
min_size = (vsn == SDIO_SDIO_REV_1_00) ? 28 : 42;
else
ret = cistpl_funce_common(card, buf, size);
- if (ret) {
+ if (ret && ret != -EILSEQ) {
printk(KERN_ERR "%s: bad CISTPL_FUNCE size %u "
"type %u\n", mmc_hostname(card->host), size, buf[0]);
- return ret;
}
- return 0;
+ return ret;
}
typedef int (tpl_parse_t)(struct mmc_card *, struct sdio_func *,
for (i = 0; i < ARRAY_SIZE(cis_tpl_list); i++)
if (cis_tpl_list[i].code == tpl_code)
break;
- if (i >= ARRAY_SIZE(cis_tpl_list)) {
- /* this tuple is unknown to the core */
- this->next = NULL;
- this->code = tpl_code;
- this->size = tpl_link;
- *prev = this;
- prev = &this->next;
- printk(KERN_DEBUG
- "%s: queuing CIS tuple 0x%02x length %u\n",
- mmc_hostname(card->host), tpl_code, tpl_link);
- } else {
+ if (i < ARRAY_SIZE(cis_tpl_list)) {
const struct cis_tpl *tpl = cis_tpl_list + i;
if (tpl_link < tpl->min_size) {
printk(KERN_ERR
- "%s: bad CIS tuple 0x%02x (length = %u, expected >= %u)\n",
+ "%s: bad CIS tuple 0x%02x"
+ " (length = %u, expected >= %u)\n",
mmc_hostname(card->host),
tpl_code, tpl_link, tpl->min_size);
ret = -EINVAL;
ret = tpl->parse(card, func,
this->data, tpl_link);
}
- kfree(this);
+ /*
+ * We don't need the tuple anymore if it was
+ * successfully parsed by the SDIO core or if it is
+ * not going to be parsed by SDIO drivers.
+ */
+ if (!ret || ret != -EILSEQ)
+ kfree(this);
+ } else {
+ /* unknown tuple */
+ ret = -EILSEQ;
+ }
+
+ if (ret == -EILSEQ) {
+ /* this tuple is unknown to the core or whitelisted */
+ this->next = NULL;
+ this->code = tpl_code;
+ this->size = tpl_link;
+ *prev = this;
+ prev = &this->next;
+ printk(KERN_DEBUG
+ "%s: queuing CIS tuple 0x%02x length %u\n",
+ mmc_hostname(card->host), tpl_code, tpl_link);
+ /* keep on analyzing tuples */
+ ret = 0;
}
ptr += tpl_link;
If unsure, say N.
+config MMC_S3C_HW_SDIO_IRQ
+ bool "Hardware support for SDIO IRQ"
+ depends on MMC_S3C
+ help
+ Enable the hardware support for SDIO interrupts instead of using
+ the generic polling code.
+
+choice
+ prompt "Samsung S3C SD/MMC transfer code"
+ depends on MMC_S3C
+
+config MMC_S3C_PIO
+ bool "Use PIO transfers only"
+ help
+ Use PIO to transfer data between memory and the hardware.
+
+ PIO is slower than DMA as it requires CPU instructions to
+ move the data. This has been the traditional default for
+ the S3C MCI driver.
+
+config MMC_S3C_DMA
+ bool "Use DMA transfers only (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ help
+ Use DMA to transfer data between memory and the hardare.
+
+ Currently, the DMA support in this driver seems to not be
+ working properly and needs to be debugged before this
+ option is useful.
+
+config MMC_S3C_PIODMA
+ bool "Support for both PIO and DMA (EXPERIMENTAL)"
+ help
+ Compile both the PIO and DMA transfer routines into the
+ driver and let the platform select at run-time which one
+ is best.
+
+ See notes for the DMA option.
+
+endchoice
+
config MMC_SDRICOH_CS
tristate "MMC/SD driver for Ricoh Bay1Controllers (EXPERIMENTAL)"
depends on EXPERIMENTAL && PCI && PCMCIA
struct scatterlist *sg;
unsigned int i;
enum dma_data_direction direction;
+ unsigned int sglen;
/*
* We don't do DMA on "complex" transfers, i.e. with
else
direction = DMA_TO_DEVICE;
+ sglen = dma_map_sg(&host->pdev->dev, data->sg, data->sg_len, direction);
+ if (sglen != data->sg_len)
+ goto unmap_exit;
desc = chan->device->device_prep_slave_sg(chan,
data->sg, data->sg_len, direction,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!desc)
- return -ENOMEM;
+ goto unmap_exit;
host->dma.data_desc = desc;
desc->callback = atmci_dma_complete;
chan->device->device_issue_pending(chan);
return 0;
+unmap_exit:
+ dma_unmap_sg(&host->pdev->dev, data->sg, sglen, direction);
+ return -ENOMEM;
}
#else /* CONFIG_MMC_ATMELMCI_DMA */
#include <linux/clk.h>
#include <linux/scatterlist.h>
#include <linux/gpio.h>
+#include <linux/amba/mmci.h>
+#include <linux/regulator/consumer.h>
#include <asm/cacheflush.h>
#include <asm/div64.h>
#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/mach/mmc.h>
#include "mmci.h"
static unsigned int fmax = 515633;
+/*
+ * This must be called with host->lock held
+ */
+static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
+{
+ u32 clk = 0;
+
+ if (desired) {
+ if (desired >= host->mclk) {
+ clk = MCI_CLK_BYPASS;
+ host->cclk = host->mclk;
+ } else {
+ clk = host->mclk / (2 * desired) - 1;
+ if (clk >= 256)
+ clk = 255;
+ host->cclk = host->mclk / (2 * (clk + 1));
+ }
+ if (host->hw_designer == 0x80)
+ clk |= MCI_FCEN; /* Bug fix in ST IP block */
+ clk |= MCI_CLK_ENABLE;
+ /* This hasn't proven to be worthwhile */
+ /* clk |= MCI_CLK_PWRSAVE; */
+ }
+
+ if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4)
+ clk |= MCI_WIDE_BUS;
+
+ writel(clk, host->base + MMCICLOCK);
+}
+
static void
mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
{
static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct mmci_host *host = mmc_priv(mmc);
- u32 clk = 0, pwr = 0;
-
- if (ios->clock) {
- if (ios->clock >= host->mclk) {
- clk = MCI_CLK_BYPASS;
- host->cclk = host->mclk;
- } else {
- clk = host->mclk / (2 * ios->clock) - 1;
- if (clk >= 256)
- clk = 255;
- host->cclk = host->mclk / (2 * (clk + 1));
- }
- if (host->hw_designer == AMBA_VENDOR_ST)
- clk |= MCI_FCEN; /* Bug fix in ST IP block */
- clk |= MCI_CLK_ENABLE;
- }
-
- if (host->plat->translate_vdd)
- pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
+ u32 pwr = 0;
+ unsigned long flags;
switch (ios->power_mode) {
case MMC_POWER_OFF:
+ if(host->vcc &&
+ regulator_is_enabled(host->vcc))
+ regulator_disable(host->vcc);
break;
case MMC_POWER_UP:
+#ifdef CONFIG_REGULATOR
+ if (host->vcc)
+ /* This implicitly enables the regulator */
+ mmc_regulator_set_ocr(host->vcc, ios->vdd);
+#endif
+ /*
+ * The translate_vdd function is not used if you have
+ * an external regulator, or your design is really weird.
+ * Using it would mean sending in power control BOTH using
+ * a regulator AND the 4 MMCIPWR bits. If we don't have
+ * a regulator, we might have some other platform specific
+ * power control behind this translate function.
+ */
+ if (!host->vcc && host->plat->translate_vdd)
+ pwr |= host->plat->translate_vdd(mmc_dev(mmc), ios->vdd);
/* The ST version does not have this, fall through to POWER_ON */
if (host->hw_designer != AMBA_VENDOR_ST) {
pwr |= MCI_PWR_UP;
}
}
- writel(clk, host->base + MMCICLOCK);
+ spin_lock_irqsave(&host->lock, flags);
+
+ mmci_set_clkreg(host, ios->clock);
if (host->pwr != pwr) {
host->pwr = pwr;
writel(pwr, host->base + MMCIPOWER);
}
+
+ spin_unlock_irqrestore(&host->lock, flags);
}
static int mmci_get_ro(struct mmc_host *mmc)
static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
{
- struct mmc_platform_data *plat = dev->dev.platform_data;
+ struct mmci_platform_data *plat = dev->dev.platform_data;
struct mmci_host *host;
struct mmc_host *mmc;
int ret;
mmc->ops = &mmci_ops;
mmc->f_min = (host->mclk + 511) / 512;
mmc->f_max = min(host->mclk, fmax);
- mmc->ocr_avail = plat->ocr_mask;
+#ifdef CONFIG_REGULATOR
+ /* If we're using the regulator framework, try to fetch a regulator */
+ host->vcc = regulator_get(&dev->dev, "vmmc");
+ if (IS_ERR(host->vcc))
+ host->vcc = NULL;
+ else {
+ int mask = mmc_regulator_get_ocrmask(host->vcc);
+
+ if (mask < 0)
+ dev_err(&dev->dev, "error getting OCR mask (%d)\n",
+ mask);
+ else {
+ host->mmc->ocr_avail = (u32) mask;
+ if (plat->ocr_mask)
+ dev_warn(&dev->dev,
+ "Provided ocr_mask/setpower will not be used "
+ "(using regulator instead)\n");
+ }
+ }
+#endif
+ /* Fall back to platform data if no regulator is found */
+ if (host->vcc == NULL)
+ mmc->ocr_avail = plat->ocr_mask;
+ mmc->caps = plat->capabilities;
/*
* We can do SGIO
writel(0, host->base + MMCIMASK1);
writel(0xfff, host->base + MMCICLEAR);
-#ifdef CONFIG_GPIOLIB
if (gpio_is_valid(plat->gpio_cd)) {
ret = gpio_request(plat->gpio_cd, DRIVER_NAME " (cd)");
if (ret == 0)
else if (ret != -ENOSYS)
goto err_gpio_wp;
}
-#endif
ret = request_irq(dev->irq[0], mmci_irq, IRQF_SHARED, DRIVER_NAME " (cmd)", host);
if (ret)
clk_disable(host->clk);
clk_put(host->clk);
+ if (regulator_is_enabled(host->vcc))
+ regulator_disable(host->vcc);
+ regulator_put(host->vcc);
+
mmc_free_host(mmc);
amba_release_regions(dev);
unsigned int mclk;
unsigned int cclk;
u32 pwr;
- struct mmc_platform_data *plat;
+ struct mmci_platform_data *plat;
u8 hw_designer;
u8 hw_revision:4;
struct scatterlist *sg_ptr;
unsigned int sg_off;
unsigned int size;
+ struct regulator *vcc;
};
static inline void mmci_init_sg(struct mmci_host *host, struct mmc_data *data)
#include <linux/mmc/host.h>
#include <linux/io.h>
#include <linux/regulator/consumer.h>
+#include <linux/gpio.h>
#include <asm/sizes.h>
static inline void pxamci_set_power(struct pxamci_host *host, unsigned int vdd)
{
+ int on;
+
#ifdef CONFIG_REGULATOR
if (host->vcc)
mmc_regulator_set_ocr(host->vcc, vdd);
#endif
+ if (!host->vcc && host->pdata &&
+ gpio_is_valid(host->pdata->gpio_power)) {
+ on = ((1 << vdd) & host->pdata->ocr_mask);
+ gpio_set_value(host->pdata->gpio_power,
+ !!on ^ host->pdata->gpio_power_invert);
+ }
if (!host->vcc && host->pdata && host->pdata->setpower)
host->pdata->setpower(mmc_dev(host->mmc), vdd);
}
{
struct pxamci_host *host = mmc_priv(mmc);
+ if (host->pdata && gpio_is_valid(host->pdata->gpio_card_ro)) {
+ if (host->pdata->gpio_card_ro_invert)
+ return !gpio_get_value(host->pdata->gpio_card_ro);
+ else
+ return gpio_get_value(host->pdata->gpio_card_ro);
+ }
if (host->pdata && host->pdata->get_ro)
return !!host->pdata->get_ro(mmc_dev(mmc));
/*
struct mmc_host *mmc;
struct pxamci_host *host = NULL;
struct resource *r, *dmarx, *dmatx;
- int ret, irq;
+ int ret, irq, gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_irq(pdev, 0);
}
host->dma_drcmrtx = dmatx->start;
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_power)) {
+ ret = gpio_request(gpio_power, "mmc card power");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_power %d\n", gpio_power);
+ goto out;
+ }
+ gpio_direction_output(gpio_power,
+ host->pdata->gpio_power_invert);
+ }
+ if (gpio_is_valid(gpio_ro)) {
+ ret = gpio_request(gpio_ro, "mmc card read only");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_ro %d\n", gpio_power);
+ goto err_gpio_ro;
+ }
+ gpio_direction_input(gpio_ro);
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ ret = gpio_request(gpio_cd, "mmc card detect");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_cd %d\n", gpio_power);
+ goto err_gpio_cd;
+ }
+ gpio_direction_input(gpio_cd);
+
+ ret = request_irq(gpio_to_irq(gpio_cd), pxamci_detect_irq,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "mmc card detect", mmc);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request card detect IRQ\n");
+ goto err_request_irq;
+ }
+ }
+
if (host->pdata && host->pdata->init)
host->pdata->init(&pdev->dev, pxamci_detect_irq, mmc);
+ if (gpio_is_valid(gpio_power) && host->pdata->setpower)
+ dev_warn(&pdev->dev, "gpio_power and setpower() both defined\n");
+ if (gpio_is_valid(gpio_ro) && host->pdata->get_ro)
+ dev_warn(&pdev->dev, "gpio_ro and get_ro() both defined\n");
+
mmc_add_host(mmc);
return 0;
+err_request_irq:
+ gpio_free(gpio_cd);
+err_gpio_cd:
+ gpio_free(gpio_ro);
+err_gpio_ro:
+ gpio_free(gpio_power);
out:
if (host) {
if (host->dma >= 0)
static int pxamci_remove(struct platform_device *pdev)
{
struct mmc_host *mmc = platform_get_drvdata(pdev);
+ int gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
platform_set_drvdata(pdev, NULL);
if (mmc) {
struct pxamci_host *host = mmc_priv(mmc);
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ free_irq(gpio_to_irq(gpio_cd), mmc);
+ gpio_free(gpio_cd);
+ }
+ if (gpio_is_valid(gpio_ro))
+ gpio_free(gpio_ro);
+ if (gpio_is_valid(gpio_power))
+ gpio_free(gpio_power);
if (host->vcc)
regulator_put(host->vcc);
}
#ifdef CONFIG_PM
-static int pxamci_suspend(struct platform_device *dev, pm_message_t state)
+static int pxamci_suspend(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = dev_get_drvdata(dev);
int ret = 0;
if (mmc)
- ret = mmc_suspend_host(mmc, state);
+ ret = mmc_suspend_host(mmc, PMSG_SUSPEND);
return ret;
}
-static int pxamci_resume(struct platform_device *dev)
+static int pxamci_resume(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = dev_get_drvdata(dev);
int ret = 0;
if (mmc)
return ret;
}
-#else
-#define pxamci_suspend NULL
-#define pxamci_resume NULL
+
+static struct dev_pm_ops pxamci_pm_ops = {
+ .suspend = pxamci_suspend,
+ .resume = pxamci_resume,
+};
#endif
static struct platform_driver pxamci_driver = {
.probe = pxamci_probe,
.remove = pxamci_remove,
- .suspend = pxamci_suspend,
- .resume = pxamci_resume,
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxamci_pm_ops,
+#endif
},
};
#include <linux/mmc/host.h>
#include <linux/platform_device.h>
#include <linux/cpufreq.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/io.h>
dev_dbg(&host->pdev->dev, args); \
} while (0)
-#define RESSIZE(ressource) (((ressource)->end - (ressource)->start)+1)
-
static struct s3c2410_dma_client s3cmci_dma_client = {
.name = "s3c-mci",
};
#endif /* CONFIG_MMC_DEBUG */
+/**
+ * s3cmci_host_usedma - return whether the host is using dma or pio
+ * @host: The host state
+ *
+ * Return true if the host is using DMA to transfer data, else false
+ * to use PIO mode. Will return static data depending on the driver
+ * configuration.
+ */
+static inline bool s3cmci_host_usedma(struct s3cmci_host *host)
+{
+#ifdef CONFIG_MMC_S3C_PIO
+ return false;
+#elif defined(CONFIG_MMC_S3C_DMA)
+ return true;
+#else
+ return host->dodma;
+#endif
+}
+
+/**
+ * s3cmci_host_canpio - return true if host has pio code available
+ *
+ * Return true if the driver has been compiled with the PIO support code
+ * available.
+ */
+static inline bool s3cmci_host_canpio(void)
+{
+#ifdef CONFIG_MMC_S3C_PIO
+ return true;
+#else
+ return false;
+#endif
+}
+
static inline u32 enable_imask(struct s3cmci_host *host, u32 imask)
{
u32 newmask;
static inline void clear_imask(struct s3cmci_host *host)
{
- writel(0, host->base + host->sdiimsk);
+ u32 mask = readl(host->base + host->sdiimsk);
+
+ /* preserve the SDIO IRQ mask state */
+ mask &= S3C2410_SDIIMSK_SDIOIRQ;
+ writel(mask, host->base + host->sdiimsk);
+}
+
+/**
+ * s3cmci_check_sdio_irq - test whether the SDIO IRQ is being signalled
+ * @host: The host to check.
+ *
+ * Test to see if the SDIO interrupt is being signalled in case the
+ * controller has failed to re-detect a card interrupt. Read GPE8 and
+ * see if it is low and if so, signal a SDIO interrupt.
+ *
+ * This is currently called if a request is finished (we assume that the
+ * bus is now idle) and when the SDIO IRQ is enabled in case the IRQ is
+ * already being indicated.
+*/
+static void s3cmci_check_sdio_irq(struct s3cmci_host *host)
+{
+ if (host->sdio_irqen) {
+ if (gpio_get_value(S3C2410_GPE(8)) == 0) {
+ printk(KERN_DEBUG "%s: signalling irq\n", __func__);
+ mmc_signal_sdio_irq(host->mmc);
+ }
+ }
}
static inline int get_data_buffer(struct s3cmci_host *host,
return 63 - fifostat;
}
+/**
+ * s3cmci_enable_irq - enable IRQ, after having disabled it.
+ * @host: The device state.
+ * @more: True if more IRQs are expected from transfer.
+ *
+ * Enable the main IRQ if needed after it has been disabled.
+ *
+ * The IRQ can be one of the following states:
+ * - disabled during IDLE
+ * - disabled whilst processing data
+ * - enabled during transfer
+ * - enabled whilst awaiting SDIO interrupt detection
+ */
+static void s3cmci_enable_irq(struct s3cmci_host *host, bool more)
+{
+ unsigned long flags;
+ bool enable = false;
+
+ local_irq_save(flags);
+
+ host->irq_enabled = more;
+ host->irq_disabled = false;
+
+ enable = more | host->sdio_irqen;
+
+ if (host->irq_state != enable) {
+ host->irq_state = enable;
+
+ if (enable)
+ enable_irq(host->irq);
+ else
+ disable_irq(host->irq);
+ }
+
+ local_irq_restore(flags);
+}
+
+/**
+ *
+ */
+static void s3cmci_disable_irq(struct s3cmci_host *host, bool transfer)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+
+ //printk(KERN_DEBUG "%s: transfer %d\n", __func__, transfer);
+
+ host->irq_disabled = transfer;
+
+ if (transfer && host->irq_state) {
+ host->irq_state = false;
+ disable_irq(host->irq);
+ }
+
+ local_irq_restore(flags);
+}
+
static void do_pio_read(struct s3cmci_host *host)
{
int res;
{
struct s3cmci_host *host = (struct s3cmci_host *) data;
-
- disable_irq(host->irq);
+ s3cmci_disable_irq(host, true);
if (host->pio_active == XFER_WRITE)
do_pio_write(host);
host->mrq->data->error = -EINVAL;
}
+ s3cmci_enable_irq(host, false);
finalize_request(host);
} else
- enable_irq(host->irq);
+ s3cmci_enable_irq(host, true);
}
/*
struct s3cmci_host *host = dev_id;
struct mmc_command *cmd;
u32 mci_csta, mci_dsta, mci_fsta, mci_dcnt, mci_imsk;
- u32 mci_cclear, mci_dclear;
+ u32 mci_cclear = 0, mci_dclear;
unsigned long iflags;
+ mci_dsta = readl(host->base + S3C2410_SDIDSTA);
+ mci_imsk = readl(host->base + host->sdiimsk);
+
+ if (mci_dsta & S3C2410_SDIDSTA_SDIOIRQDETECT) {
+ if (mci_imsk & S3C2410_SDIIMSK_SDIOIRQ) {
+ mci_dclear = S3C2410_SDIDSTA_SDIOIRQDETECT;
+ writel(mci_dclear, host->base + S3C2410_SDIDSTA);
+
+ mmc_signal_sdio_irq(host->mmc);
+ return IRQ_HANDLED;
+ }
+ }
+
spin_lock_irqsave(&host->complete_lock, iflags);
mci_csta = readl(host->base + S3C2410_SDICMDSTAT);
- mci_dsta = readl(host->base + S3C2410_SDIDSTA);
mci_dcnt = readl(host->base + S3C2410_SDIDCNT);
mci_fsta = readl(host->base + S3C2410_SDIFSTA);
- mci_imsk = readl(host->base + host->sdiimsk);
- mci_cclear = 0;
mci_dclear = 0;
if ((host->complete_what == COMPLETION_NONE) ||
goto irq_out;
}
- if (!host->dodma) {
+ if (!s3cmci_host_usedma(host)) {
if ((host->pio_active == XFER_WRITE) &&
(mci_fsta & S3C2410_SDIFSTA_TFDET)) {
dbg(host, dbg_dma, "DMA FINISHED Size:%i DSTA:%08x DCNT:%08x\n",
size, mci_dsta, mci_dcnt);
+ host->dma_complete = 1;
host->complete_what = COMPLETION_FINALIZE;
out:
fail_request:
host->mrq->data->error = -EINVAL;
host->complete_what = COMPLETION_FINALIZE;
- writel(0, host->base + host->sdiimsk);
- goto out;
+ clear_imask(host);
+ goto out;
}
static void finalize_request(struct s3cmci_host *host)
if (cmd->data && (cmd->error == 0) &&
(cmd->data->error == 0)) {
- if (host->dodma && (!host->dma_complete)) {
- dbg(host, dbg_dma, "DMA Missing!\n");
+ if (s3cmci_host_usedma(host) && (!host->dma_complete)) {
+ dbg(host, dbg_dma, "DMA Missing (%d)!\n",
+ host->dma_complete);
return;
}
}
writel(0, host->base + S3C2410_SDICMDARG);
writel(S3C2410_SDIDCON_STOP, host->base + S3C2410_SDIDCON);
writel(0, host->base + S3C2410_SDICMDCON);
- writel(0, host->base + host->sdiimsk);
+ clear_imask(host);
if (cmd->data && cmd->error)
cmd->data->error = cmd->error;
/* If we had an error while transfering data we flush the
* DMA channel and the fifo to clear out any garbage. */
if (mrq->data->error != 0) {
- if (host->dodma)
+ if (s3cmci_host_usedma(host))
s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH);
if (host->is2440) {
request_done:
host->complete_what = COMPLETION_NONE;
host->mrq = NULL;
+
+ s3cmci_check_sdio_irq(host);
mmc_request_done(host->mmc, mrq);
}
dcon = data->blocks & S3C2410_SDIDCON_BLKNUM_MASK;
- if (host->dodma)
+ if (s3cmci_host_usedma(host))
dcon |= S3C2410_SDIDCON_DMAEN;
if (host->bus_width == MMC_BUS_WIDTH_4)
static int s3cmci_prepare_dma(struct s3cmci_host *host, struct mmc_data *data)
{
int dma_len, i;
- int rw = (data->flags & MMC_DATA_WRITE) ? 1 : 0;
+ int rw = data->flags & MMC_DATA_WRITE;
BUG_ON((data->flags & BOTH_DIR) == BOTH_DIR);
s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_FLUSH);
dma_len = dma_map_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
- (rw) ? DMA_TO_DEVICE : DMA_FROM_DEVICE);
+ rw ? DMA_TO_DEVICE : DMA_FROM_DEVICE);
if (dma_len == 0)
return -ENOMEM;
for (i = 0; i < dma_len; i++) {
int res;
- dbg(host, dbg_dma, "enqueue %i:%u@%u\n", i,
- sg_dma_address(&data->sg[i]),
- sg_dma_len(&data->sg[i]));
+ dbg(host, dbg_dma, "enqueue %i: %08x@%u\n", i,
+ sg_dma_address(&data->sg[i]),
+ sg_dma_len(&data->sg[i]));
- res = s3c2410_dma_enqueue(host->dma, (void *) host,
+ res = s3c2410_dma_enqueue(host->dma, host,
sg_dma_address(&data->sg[i]),
sg_dma_len(&data->sg[i]));
return;
}
- if (host->dodma)
+ if (s3cmci_host_usedma(host))
res = s3cmci_prepare_dma(host, cmd->data);
else
res = s3cmci_prepare_pio(host, cmd->data);
s3cmci_send_command(host, cmd);
/* Enable Interrupt */
- enable_irq(host->irq);
+ s3cmci_enable_irq(host, true);
}
static int s3cmci_card_present(struct mmc_host *mmc)
if (pdata->gpio_detect == 0)
return -ENOSYS;
- ret = s3c2410_gpio_getpin(pdata->gpio_detect) ? 0 : 1;
+ ret = gpio_get_value(pdata->gpio_detect) ? 0 : 1;
return ret ^ pdata->detect_invert;
}
switch (ios->power_mode) {
case MMC_POWER_ON:
case MMC_POWER_UP:
- s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_SDCLK);
- s3c2410_gpio_cfgpin(S3C2410_GPE6, S3C2410_GPE6_SDCMD);
- s3c2410_gpio_cfgpin(S3C2410_GPE7, S3C2410_GPE7_SDDAT0);
- s3c2410_gpio_cfgpin(S3C2410_GPE8, S3C2410_GPE8_SDDAT1);
- s3c2410_gpio_cfgpin(S3C2410_GPE9, S3C2410_GPE9_SDDAT2);
- s3c2410_gpio_cfgpin(S3C2410_GPE10, S3C2410_GPE10_SDDAT3);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(5), S3C2410_GPE5_SDCLK);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(6), S3C2410_GPE6_SDCMD);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(7), S3C2410_GPE7_SDDAT0);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(8), S3C2410_GPE8_SDDAT1);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(9), S3C2410_GPE9_SDDAT2);
+ s3c2410_gpio_cfgpin(S3C2410_GPE(10), S3C2410_GPE10_SDDAT3);
if (host->pdata->set_power)
host->pdata->set_power(ios->power_mode, ios->vdd);
case MMC_POWER_OFF:
default:
- s3c2410_gpio_setpin(S3C2410_GPE5, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPIO_OUTPUT);
+ gpio_direction_output(S3C2410_GPE(5), 0);
if (host->is2440)
mci_con |= S3C2440_SDICON_SDRESET;
struct s3c24xx_mci_pdata *pdata = host->pdata;
int ret;
- if (pdata->gpio_wprotect == 0)
+ if (pdata->no_wprotect)
return 0;
ret = s3c2410_gpio_getpin(pdata->gpio_wprotect);
return ret;
}
+static void s3cmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+ struct s3cmci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+ u32 con;
+
+ local_irq_save(flags);
+
+ con = readl(host->base + S3C2410_SDICON);
+ host->sdio_irqen = enable;
+
+ if (enable == host->sdio_irqen)
+ goto same_state;
+
+ if (enable) {
+ con |= S3C2410_SDICON_SDIOIRQ;
+ enable_imask(host, S3C2410_SDIIMSK_SDIOIRQ);
+
+ if (!host->irq_state && !host->irq_disabled) {
+ host->irq_state = true;
+ enable_irq(host->irq);
+ }
+ } else {
+ disable_imask(host, S3C2410_SDIIMSK_SDIOIRQ);
+ con &= ~S3C2410_SDICON_SDIOIRQ;
+
+ if (!host->irq_enabled && host->irq_state) {
+ disable_irq_nosync(host->irq);
+ host->irq_state = false;
+ }
+ }
+
+ writel(con, host->base + S3C2410_SDICON);
+
+ same_state:
+ local_irq_restore(flags);
+
+ s3cmci_check_sdio_irq(host);
+}
+
static struct mmc_host_ops s3cmci_ops = {
.request = s3cmci_request,
.set_ios = s3cmci_set_ios,
.get_ro = s3cmci_get_ro,
.get_cd = s3cmci_card_present,
+ .enable_sdio_irq = s3cmci_enable_sdio_irq,
};
static struct s3c24xx_mci_pdata s3cmci_def_pdata = {
}
#endif
-static int __devinit s3cmci_probe(struct platform_device *pdev, int is2440)
+
+#ifdef CONFIG_DEBUG_FS
+
+static int s3cmci_state_show(struct seq_file *seq, void *v)
+{
+ struct s3cmci_host *host = seq->private;
+
+ seq_printf(seq, "Register base = 0x%08x\n", (u32)host->base);
+ seq_printf(seq, "Clock rate = %ld\n", host->clk_rate);
+ seq_printf(seq, "Prescale = %d\n", host->prescaler);
+ seq_printf(seq, "is2440 = %d\n", host->is2440);
+ seq_printf(seq, "IRQ = %d\n", host->irq);
+ seq_printf(seq, "IRQ enabled = %d\n", host->irq_enabled);
+ seq_printf(seq, "IRQ disabled = %d\n", host->irq_disabled);
+ seq_printf(seq, "IRQ state = %d\n", host->irq_state);
+ seq_printf(seq, "CD IRQ = %d\n", host->irq_cd);
+ seq_printf(seq, "Do DMA = %d\n", s3cmci_host_usedma(host));
+ seq_printf(seq, "SDIIMSK at %d\n", host->sdiimsk);
+ seq_printf(seq, "SDIDATA at %d\n", host->sdidata);
+
+ return 0;
+}
+
+static int s3cmci_state_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, s3cmci_state_show, inode->i_private);
+}
+
+static const struct file_operations s3cmci_fops_state = {
+ .owner = THIS_MODULE,
+ .open = s3cmci_state_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+#define DBG_REG(_r) { .addr = S3C2410_SDI##_r, .name = #_r }
+
+struct s3cmci_reg {
+ unsigned short addr;
+ unsigned char *name;
+} debug_regs[] = {
+ DBG_REG(CON),
+ DBG_REG(PRE),
+ DBG_REG(CMDARG),
+ DBG_REG(CMDCON),
+ DBG_REG(CMDSTAT),
+ DBG_REG(RSP0),
+ DBG_REG(RSP1),
+ DBG_REG(RSP2),
+ DBG_REG(RSP3),
+ DBG_REG(TIMER),
+ DBG_REG(BSIZE),
+ DBG_REG(DCON),
+ DBG_REG(DCNT),
+ DBG_REG(DSTA),
+ DBG_REG(FSTA),
+ {}
+};
+
+static int s3cmci_regs_show(struct seq_file *seq, void *v)
+{
+ struct s3cmci_host *host = seq->private;
+ struct s3cmci_reg *rptr = debug_regs;
+
+ for (; rptr->name; rptr++)
+ seq_printf(seq, "SDI%s\t=0x%08x\n", rptr->name,
+ readl(host->base + rptr->addr));
+
+ seq_printf(seq, "SDIIMSK\t=0x%08x\n", readl(host->base + host->sdiimsk));
+
+ return 0;
+}
+
+static int s3cmci_regs_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, s3cmci_regs_show, inode->i_private);
+}
+
+static const struct file_operations s3cmci_fops_regs = {
+ .owner = THIS_MODULE,
+ .open = s3cmci_regs_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static void s3cmci_debugfs_attach(struct s3cmci_host *host)
+{
+ struct device *dev = &host->pdev->dev;
+
+ host->debug_root = debugfs_create_dir(dev_name(dev), NULL);
+ if (IS_ERR(host->debug_root)) {
+ dev_err(dev, "failed to create debugfs root\n");
+ return;
+ }
+
+ host->debug_state = debugfs_create_file("state", 0444,
+ host->debug_root, host,
+ &s3cmci_fops_state);
+
+ if (IS_ERR(host->debug_state))
+ dev_err(dev, "failed to create debug state file\n");
+
+ host->debug_regs = debugfs_create_file("regs", 0444,
+ host->debug_root, host,
+ &s3cmci_fops_regs);
+
+ if (IS_ERR(host->debug_regs))
+ dev_err(dev, "failed to create debug regs file\n");
+}
+
+static void s3cmci_debugfs_remove(struct s3cmci_host *host)
+{
+ debugfs_remove(host->debug_regs);
+ debugfs_remove(host->debug_state);
+ debugfs_remove(host->debug_root);
+}
+
+#else
+static inline void s3cmci_debugfs_attach(struct s3cmci_host *host) { }
+static inline void s3cmci_debugfs_remove(struct s3cmci_host *host) { }
+
+#endif /* CONFIG_DEBUG_FS */
+
+static int __devinit s3cmci_probe(struct platform_device *pdev)
{
struct s3cmci_host *host;
struct mmc_host *mmc;
int ret;
+ int is2440;
+ int i;
+
+ is2440 = platform_get_device_id(pdev)->driver_data;
mmc = mmc_alloc_host(sizeof(struct s3cmci_host), &pdev->dev);
if (!mmc) {
goto probe_out;
}
+ for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++) {
+ ret = gpio_request(i, dev_name(&pdev->dev));
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get gpio %d\n", i);
+
+ for (i--; i >= S3C2410_GPE(5); i--)
+ gpio_free(i);
+
+ goto probe_free_host;
+ }
+ }
+
host = mmc_priv(mmc);
host->mmc = mmc;
host->pdev = pdev;
host->clk_div = 2;
}
- host->dodma = 0;
host->complete_what = COMPLETION_NONE;
host->pio_active = XFER_NONE;
- host->dma = S3CMCI_DMA;
+#ifdef CONFIG_MMC_S3C_PIODMA
+ host->dodma = host->pdata->dma;
+#endif
host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!host->mem) {
"failed to get io memory region resouce.\n");
ret = -ENOENT;
- goto probe_free_host;
+ goto probe_free_gpio;
}
host->mem = request_mem_region(host->mem->start,
- RESSIZE(host->mem), pdev->name);
+ resource_size(host->mem), pdev->name);
if (!host->mem) {
dev_err(&pdev->dev, "failed to request io memory region.\n");
ret = -ENOENT;
- goto probe_free_host;
+ goto probe_free_gpio;
}
- host->base = ioremap(host->mem->start, RESSIZE(host->mem));
+ host->base = ioremap(host->mem->start, resource_size(host->mem));
if (!host->base) {
dev_err(&pdev->dev, "failed to ioremap() io memory region.\n");
ret = -EINVAL;
* ensure we don't lock the system with un-serviceable requests. */
disable_irq(host->irq);
+ host->irq_state = false;
- host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect);
-
- if (host->irq_cd >= 0) {
- if (request_irq(host->irq_cd, s3cmci_irq_cd,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- DRIVER_NAME, host)) {
- dev_err(&pdev->dev, "can't get card detect irq.\n");
- ret = -ENOENT;
+ if (!host->pdata->no_detect) {
+ ret = gpio_request(host->pdata->gpio_detect, "s3cmci detect");
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get detect gpio\n");
goto probe_free_irq;
}
- } else {
- dev_warn(&pdev->dev, "host detect has no irq available\n");
- s3c2410_gpio_cfgpin(host->pdata->gpio_detect,
- S3C2410_GPIO_INPUT);
+
+ host->irq_cd = s3c2410_gpio_getirq(host->pdata->gpio_detect);
+
+ if (host->irq_cd >= 0) {
+ if (request_irq(host->irq_cd, s3cmci_irq_cd,
+ IRQF_TRIGGER_RISING |
+ IRQF_TRIGGER_FALLING,
+ DRIVER_NAME, host)) {
+ dev_err(&pdev->dev,
+ "can't get card detect irq.\n");
+ ret = -ENOENT;
+ goto probe_free_gpio_cd;
+ }
+ } else {
+ dev_warn(&pdev->dev,
+ "host detect has no irq available\n");
+ gpio_direction_input(host->pdata->gpio_detect);
+ }
+ } else
+ host->irq_cd = -1;
+
+ if (!host->pdata->no_wprotect) {
+ ret = gpio_request(host->pdata->gpio_wprotect, "s3cmci wp");
+ if (ret) {
+ dev_err(&pdev->dev, "failed to get writeprotect\n");
+ goto probe_free_irq_cd;
+ }
+
+ gpio_direction_input(host->pdata->gpio_wprotect);
}
- if (host->pdata->gpio_wprotect)
- s3c2410_gpio_cfgpin(host->pdata->gpio_wprotect,
- S3C2410_GPIO_INPUT);
+ /* depending on the dma state, get a dma channel to use. */
- if (s3c2410_dma_request(S3CMCI_DMA, &s3cmci_dma_client, NULL) < 0) {
- dev_err(&pdev->dev, "unable to get DMA channel.\n");
- ret = -EBUSY;
- goto probe_free_irq_cd;
+ if (s3cmci_host_usedma(host)) {
+ host->dma = s3c2410_dma_request(DMACH_SDI, &s3cmci_dma_client,
+ host);
+ if (host->dma < 0) {
+ dev_err(&pdev->dev, "cannot get DMA channel.\n");
+ if (!s3cmci_host_canpio()) {
+ ret = -EBUSY;
+ goto probe_free_gpio_wp;
+ } else {
+ dev_warn(&pdev->dev, "falling back to PIO.\n");
+ host->dodma = 0;
+ }
+ }
}
host->clk = clk_get(&pdev->dev, "sdi");
dev_err(&pdev->dev, "failed to find clock source.\n");
ret = PTR_ERR(host->clk);
host->clk = NULL;
- goto probe_free_host;
+ goto probe_free_dma;
}
ret = clk_enable(host->clk);
mmc->ops = &s3cmci_ops;
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+#ifdef CONFIG_MMC_S3C_HW_SDIO_IRQ
+ mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
+#else
mmc->caps = MMC_CAP_4_BIT_DATA;
+#endif
mmc->f_min = host->clk_rate / (host->clk_div * 256);
mmc->f_max = host->clk_rate / host->clk_div;
goto free_cpufreq;
}
+ s3cmci_debugfs_attach(host);
+
platform_set_drvdata(pdev, mmc);
- dev_info(&pdev->dev, "initialisation done.\n");
+ dev_info(&pdev->dev, "%s - using %s, %s SDIO IRQ\n", mmc_hostname(mmc),
+ s3cmci_host_usedma(host) ? "dma" : "pio",
+ mmc->caps & MMC_CAP_SDIO_IRQ ? "hw" : "sw");
return 0;
clk_free:
clk_put(host->clk);
+ probe_free_dma:
+ if (s3cmci_host_usedma(host))
+ s3c2410_dma_free(host->dma, &s3cmci_dma_client);
+
+ probe_free_gpio_wp:
+ if (!host->pdata->no_wprotect)
+ gpio_free(host->pdata->gpio_wprotect);
+
+ probe_free_gpio_cd:
+ if (!host->pdata->no_detect)
+ gpio_free(host->pdata->gpio_detect);
+
probe_free_irq_cd:
if (host->irq_cd >= 0)
free_irq(host->irq_cd, host);
iounmap(host->base);
probe_free_mem_region:
- release_mem_region(host->mem->start, RESSIZE(host->mem));
+ release_mem_region(host->mem->start, resource_size(host->mem));
+
+ probe_free_gpio:
+ for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++)
+ gpio_free(i);
probe_free_host:
mmc_free_host(mmc);
+
probe_out:
return ret;
}
if (host->irq_cd >= 0)
free_irq(host->irq_cd, host);
+ s3cmci_debugfs_remove(host);
s3cmci_cpufreq_deregister(host);
mmc_remove_host(mmc);
clk_disable(host->clk);
{
struct mmc_host *mmc = platform_get_drvdata(pdev);
struct s3cmci_host *host = mmc_priv(mmc);
+ struct s3c24xx_mci_pdata *pd = host->pdata;
+ int i;
s3cmci_shutdown(pdev);
clk_put(host->clk);
tasklet_disable(&host->pio_tasklet);
- s3c2410_dma_free(S3CMCI_DMA, &s3cmci_dma_client);
+
+ if (s3cmci_host_usedma(host))
+ s3c2410_dma_free(host->dma, &s3cmci_dma_client);
free_irq(host->irq, host);
+ if (!pd->no_wprotect)
+ gpio_free(pd->gpio_wprotect);
+
+ if (!pd->no_detect)
+ gpio_free(pd->gpio_detect);
+
+ for (i = S3C2410_GPE(5); i <= S3C2410_GPE(10); i++)
+ gpio_free(i);
+
+
iounmap(host->base);
- release_mem_region(host->mem->start, RESSIZE(host->mem));
+ release_mem_region(host->mem->start, resource_size(host->mem));
mmc_free_host(mmc);
return 0;
}
-static int __devinit s3cmci_2410_probe(struct platform_device *dev)
-{
- return s3cmci_probe(dev, 0);
-}
+static struct platform_device_id s3cmci_driver_ids[] = {
+ {
+ .name = "s3c2410-sdi",
+ .driver_data = 0,
+ }, {
+ .name = "s3c2412-sdi",
+ .driver_data = 1,
+ }, {
+ .name = "s3c2440-sdi",
+ .driver_data = 1,
+ },
+ { }
+};
-static int __devinit s3cmci_2412_probe(struct platform_device *dev)
-{
- return s3cmci_probe(dev, 1);
-}
+MODULE_DEVICE_TABLE(platform, s3cmci_driver_ids);
-static int __devinit s3cmci_2440_probe(struct platform_device *dev)
-{
- return s3cmci_probe(dev, 1);
-}
#ifdef CONFIG_PM
-static int s3cmci_suspend(struct platform_device *dev, pm_message_t state)
+static int s3cmci_suspend(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = platform_get_drvdata(to_platform_device(dev));
+ struct pm_message event = { PM_EVENT_SUSPEND };
- return mmc_suspend_host(mmc, state);
+ return mmc_suspend_host(mmc, event);
}
-static int s3cmci_resume(struct platform_device *dev)
+static int s3cmci_resume(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = platform_get_drvdata(to_platform_device(dev));
return mmc_resume_host(mmc);
}
-#else /* CONFIG_PM */
-#define s3cmci_suspend NULL
-#define s3cmci_resume NULL
-#endif /* CONFIG_PM */
-
-
-static struct platform_driver s3cmci_2410_driver = {
- .driver.name = "s3c2410-sdi",
- .driver.owner = THIS_MODULE,
- .probe = s3cmci_2410_probe,
- .remove = __devexit_p(s3cmci_remove),
- .shutdown = s3cmci_shutdown,
+static struct dev_pm_ops s3cmci_pm = {
.suspend = s3cmci_suspend,
.resume = s3cmci_resume,
};
-static struct platform_driver s3cmci_2412_driver = {
- .driver.name = "s3c2412-sdi",
- .driver.owner = THIS_MODULE,
- .probe = s3cmci_2412_probe,
- .remove = __devexit_p(s3cmci_remove),
- .shutdown = s3cmci_shutdown,
- .suspend = s3cmci_suspend,
- .resume = s3cmci_resume,
-};
+#define s3cmci_pm_ops &s3cmci_pm
+#else /* CONFIG_PM */
+#define s3cmci_pm_ops NULL
+#endif /* CONFIG_PM */
-static struct platform_driver s3cmci_2440_driver = {
- .driver.name = "s3c2440-sdi",
- .driver.owner = THIS_MODULE,
- .probe = s3cmci_2440_probe,
+
+static struct platform_driver s3cmci_driver = {
+ .driver = {
+ .name = "s3c-sdi",
+ .owner = THIS_MODULE,
+ .pm = s3cmci_pm_ops,
+ },
+ .id_table = s3cmci_driver_ids,
+ .probe = s3cmci_probe,
.remove = __devexit_p(s3cmci_remove),
.shutdown = s3cmci_shutdown,
- .suspend = s3cmci_suspend,
- .resume = s3cmci_resume,
};
-
static int __init s3cmci_init(void)
{
- platform_driver_register(&s3cmci_2410_driver);
- platform_driver_register(&s3cmci_2412_driver);
- platform_driver_register(&s3cmci_2440_driver);
- return 0;
+ return platform_driver_register(&s3cmci_driver);
}
static void __exit s3cmci_exit(void)
{
- platform_driver_unregister(&s3cmci_2410_driver);
- platform_driver_unregister(&s3cmci_2412_driver);
- platform_driver_unregister(&s3cmci_2440_driver);
+ platform_driver_unregister(&s3cmci_driver);
}
module_init(s3cmci_init);
MODULE_DESCRIPTION("Samsung S3C MMC/SD Card Interface driver");
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Thomas Kleffel <tk@maintech.de>, Ben Dooks <ben-linux@fluff.org>");
-MODULE_ALIAS("platform:s3c2410-sdi");
-MODULE_ALIAS("platform:s3c2412-sdi");
-MODULE_ALIAS("platform:s3c2440-sdi");
* published by the Free Software Foundation.
*/
-/* FIXME: DMA Resource management ?! */
-#define S3CMCI_DMA 0
-
enum s3cmci_waitfor {
COMPLETION_NONE,
COMPLETION_FINALIZE,
int dodma;
int dmatogo;
+ bool irq_disabled;
+ bool irq_enabled;
+ bool irq_state;
+ int sdio_irqen;
+
struct mmc_request *mrq;
int cmd_is_stop;
unsigned int ccnt, dcnt;
struct tasklet_struct pio_tasklet;
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debug_root;
+ struct dentry *debug_state;
+ struct dentry *debug_regs;
+#endif
+
#ifdef CONFIG_CPU_FREQ
struct notifier_block freq_transition;
#endif
config MTD_OF_PARTS
tristate "Flash partition map based on OF description"
- depends on PPC_OF && MTD_PARTITIONS
+ depends on (MICROBLAZE || PPC_OF) && MTD_PARTITIONS
help
This provides a partition parsing function which derives
the partition map from the children of the flash node,
config MTD_PHYSMAP_OF
tristate "Flash device in physical memory map based on OF description"
- depends on PPC_OF && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM)
+ depends on (MICROBLAZE || PPC_OF) && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM)
help
This provides a 'mapping' driver which allows the NOR Flash and
ROM driver code to communicate with chips which are mapped
spinlock_t queue_lock;
};
-static int blktrans_discard_request(struct request_queue *q,
- struct request *req)
-{
- req->cmd_type = REQ_TYPE_LINUX_BLOCK;
- req->cmd[0] = REQ_LB_OP_DISCARD;
- return 0;
-}
-
static int do_blktrans_request(struct mtd_blktrans_ops *tr,
struct mtd_blktrans_dev *dev,
struct request *req)
buf = req->buffer;
- if (req->cmd_type == REQ_TYPE_LINUX_BLOCK &&
- req->cmd[0] == REQ_LB_OP_DISCARD)
- return tr->discard(dev, block, nsect);
-
if (!blk_fs_request(req))
return -EIO;
get_capacity(req->rq_disk))
return -EIO;
+ if (blk_discard_rq(req))
+ return tr->discard(dev, block, nsect);
+
switch(rq_data_dir(req)) {
case READ:
for (; nsect > 0; nsect--, block++, buf += tr->blksize)
tr->blkcore_priv->rq->queuedata = tr;
blk_queue_logical_block_size(tr->blkcore_priv->rq, tr->blksize);
if (tr->discard)
- blk_queue_set_discard(tr->blkcore_priv->rq,
- blktrans_discard_request);
+ queue_flag_set_unlocked(QUEUE_FLAG_DISCARD,
+ tr->blkcore_priv->rq);
tr->blkshift = ffs(tr->blksize) - 1;
#ifdef CONFIG_PM
-static int vortex_suspend(struct pci_dev *pdev, pm_message_t state)
+static int vortex_suspend(struct device *dev)
{
- struct net_device *dev = pci_get_drvdata(pdev);
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct net_device *ndev = pci_get_drvdata(pdev);
+
+ if (!ndev || !netif_running(ndev))
+ return 0;
+
+ netif_device_detach(ndev);
+ vortex_down(ndev, 1);
- if (dev && netdev_priv(dev)) {
- if (netif_running(dev)) {
- netif_device_detach(dev);
- vortex_down(dev, 1);
- }
- pci_save_state(pdev);
- pci_enable_wake(pdev, pci_choose_state(pdev, state), 0);
- free_irq(dev->irq, dev);
- pci_disable_device(pdev);
- pci_set_power_state(pdev, pci_choose_state(pdev, state));
- }
return 0;
}
-static int vortex_resume(struct pci_dev *pdev)
+static int vortex_resume(struct device *dev)
{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct vortex_private *vp = netdev_priv(dev);
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct net_device *ndev = pci_get_drvdata(pdev);
int err;
- if (dev && vp) {
- pci_set_power_state(pdev, PCI_D0);
- pci_restore_state(pdev);
- err = pci_enable_device(pdev);
- if (err) {
- pr_warning("%s: Could not enable device\n",
- dev->name);
- return err;
- }
- pci_set_master(pdev);
- if (request_irq(dev->irq, vp->full_bus_master_rx ?
- &boomerang_interrupt : &vortex_interrupt, IRQF_SHARED, dev->name, dev)) {
- pr_warning("%s: Could not reserve IRQ %d\n", dev->name, dev->irq);
- pci_disable_device(pdev);
- return -EBUSY;
- }
- if (netif_running(dev)) {
- err = vortex_up(dev);
- if (err)
- return err;
- else
- netif_device_attach(dev);
- }
- }
+ if (!ndev || !netif_running(ndev))
+ return 0;
+
+ err = vortex_up(ndev);
+ if (err)
+ return err;
+
+ netif_device_attach(ndev);
+
return 0;
}
-#endif /* CONFIG_PM */
+static struct dev_pm_ops vortex_pm_ops = {
+ .suspend = vortex_suspend,
+ .resume = vortex_resume,
+ .freeze = vortex_suspend,
+ .thaw = vortex_resume,
+ .poweroff = vortex_suspend,
+ .restore = vortex_resume,
+};
+
+#define VORTEX_PM_OPS (&vortex_pm_ops)
+
+#else /* !CONFIG_PM */
+
+#define VORTEX_PM_OPS NULL
+
+#endif /* !CONFIG_PM */
#ifdef CONFIG_EISA
static struct eisa_device_id vortex_eisa_ids[] = {
.probe = vortex_init_one,
.remove = __devexit_p(vortex_remove_one),
.id_table = vortex_pci_tbl,
-#ifdef CONFIG_PM
- .suspend = vortex_suspend,
- .resume = vortex_resume,
-#endif
+ .driver.pm = VORTEX_PM_OPS,
};
/* These identify the driver base version and may not be removed. */
static char version[] =
-KERN_INFO DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE ")\n";
+DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE ")\n";
MODULE_AUTHOR("Jeff Garzik <jgarzik@pobox.com>");
MODULE_DESCRIPTION("RealTek RTL-8139C+ series 10/100 PCI Ethernet driver");
help
SPI driver for Micrel KS8851 SPI attached network chip.
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
config VIA_RHINE
tristate "VIA Rhine support"
depends on NET_PCI && PCI
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
obj-$(CONFIG_SKFP) += skfp/
obj-$(CONFIG_KS8842) += ks8842.o
obj-$(CONFIG_KS8851) += ks8851.o
+obj-$(CONFIG_KS8851_MLL) += ks8851_mll.o
obj-$(CONFIG_VIA_RHINE) += via-rhine.o
obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
u32 ctrl;
u32 mac_ctrl_data;
u32 master_ctrl_data;
- u32 wol_ctrl_data;
+ u32 wol_ctrl_data = 0;
u16 mii_bmsr_data;
u16 save_autoneg_advertised;
u16 mii_intr_status_data;
if (enet_readl(priv, ENET_IR_REG) & ENET_IR_MII)
break;
udelay(1);
- } while (limit-- >= 0);
+ } while (limit-- > 0);
return (limit < 0) ? 1 : 0;
}
bool link_up;
u32 port_num;
bool promiscuous;
+ u32 cap;
};
extern const struct ethtool_ops be_ethtool_ops;
}
/* Uses mbox */
-int be_cmd_query_fw_cfg(struct be_adapter *adapter, u32 *port_num)
+int be_cmd_query_fw_cfg(struct be_adapter *adapter, u32 *port_num, u32 *cap)
{
struct be_mcc_wrb *wrb;
struct be_cmd_req_query_fw_cfg *req;
if (!status) {
struct be_cmd_resp_query_fw_cfg *resp = embedded_payload(wrb);
*port_num = le32_to_cpu(resp->phys_port);
+ *cap = le32_to_cpu(resp->function_cap);
}
spin_unlock(&adapter->mbox_lock);
u32 tx_fc, u32 rx_fc);
extern int be_cmd_get_flow_control(struct be_adapter *adapter,
u32 *tx_fc, u32 *rx_fc);
-extern int be_cmd_query_fw_cfg(struct be_adapter *adapter, u32 *port_num);
+extern int be_cmd_query_fw_cfg(struct be_adapter *adapter,
+ u32 *port_num, u32 *cap);
extern int be_cmd_reset_function(struct be_adapter *adapter);
extern int be_process_mcc(struct be_adapter *adapter);
extern int be_cmd_write_flashrom(struct be_adapter *adapter,
struct be_eth_rx_compl *rxcp)
{
struct sk_buff *skb;
- u32 vtp, vid;
+ u32 vlanf, vid;
+ u8 vtm;
- vtp = AMAP_GET_BITS(struct amap_eth_rx_compl, vtp, rxcp);
+ vlanf = AMAP_GET_BITS(struct amap_eth_rx_compl, vtp, rxcp);
+ vtm = AMAP_GET_BITS(struct amap_eth_rx_compl, vtm, rxcp);
+
+ /* vlanf could be wrongly set in some cards.
+ * ignore if vtm is not set */
+ if ((adapter->cap == 0x400) && !vtm)
+ vlanf = 0;
skb = netdev_alloc_skb(adapter->netdev, BE_HDR_LEN + NET_IP_ALIGN);
if (!skb) {
skb->protocol = eth_type_trans(skb, adapter->netdev);
skb->dev = adapter->netdev;
- if (vtp) {
+ if (vlanf) {
if (!adapter->vlan_grp || adapter->num_vlans == 0) {
kfree_skb(skb);
return;
struct be_eq_obj *eq_obj = &adapter->rx_eq;
u32 num_rcvd, pkt_size, remaining, vlanf, curr_frag_len;
u16 i, rxq_idx = 0, vid, j;
+ u8 vtm;
num_rcvd = AMAP_GET_BITS(struct amap_eth_rx_compl, numfrags, rxcp);
pkt_size = AMAP_GET_BITS(struct amap_eth_rx_compl, pktsize, rxcp);
vlanf = AMAP_GET_BITS(struct amap_eth_rx_compl, vtp, rxcp);
rxq_idx = AMAP_GET_BITS(struct amap_eth_rx_compl, fragndx, rxcp);
+ vtm = AMAP_GET_BITS(struct amap_eth_rx_compl, vtm, rxcp);
+
+ /* vlanf could be wrongly set in some cards.
+ * ignore if vtm is not set */
+ if ((adapter->cap == 0x400) && !vtm)
+ vlanf = 0;
skb = napi_get_frags(&eq_obj->napi);
if (!skb) {
if (status)
return status;
- status = be_cmd_query_fw_cfg(adapter, &adapter->port_num);
+ status = be_cmd_query_fw_cfg(adapter,
+ &adapter->port_num, &adapter->cap);
return status;
}
": %s: Setting %s as primary slave.\n",
bond->dev->name, slave->dev->name);
bond->primary_slave = slave;
+ strcpy(bond->params.primary, slave->dev->name);
bond_select_active_slave(bond);
goto out;
}
CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
(http://www.ems-wuensche.de).
+config CAN_EMS_USB
+ tristate "EMS CPC-USB/ARM7 CAN/USB interface"
+ depends on USB && CAN_DEV
+ ---help---
+ This driver is for the one channel CPC-USB/ARM7 CAN/USB interface
+ from from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
+
config CAN_KVASER_PCI
tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
depends on PCI && CAN_SJA1000
This driver is for the the PCIcanx and PCIcan cards (1, 2 or
4 channel) from Kvaser (http://www.kvaser.com).
+config CAN_AT91
+ tristate "Atmel AT91 onchip CAN controller"
+ depends on CAN && CAN_DEV && ARCH_AT91SAM9263
+ ---help---
+ This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
+
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"
depends on CAN
obj-$(CONFIG_CAN_DEV) += can-dev.o
can-dev-y := dev.o
+obj-y += usb/
+
obj-$(CONFIG_CAN_SJA1000) += sja1000/
+obj-$(CONFIG_CAN_AT91) += at91_can.o
ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG
--- /dev/null
+/*
+ * at91_can.c - CAN network driver for AT91 SoC CAN controller
+ *
+ * (C) 2007 by Hans J. Koch <hjk@linutronix.de>
+ * (C) 2008, 2009 by Marc Kleine-Budde <kernel@pengutronix.de>
+ *
+ * This software may be distributed under the terms of the GNU General
+ * Public License ("GPL") version 2 as distributed in the 'COPYING'
+ * file from the main directory of the linux kernel source.
+ *
+ * Send feedback to <socketcan-users@lists.berlios.de>
+ *
+ *
+ * Your platform definition file should specify something like:
+ *
+ * static struct at91_can_data ek_can_data = {
+ * transceiver_switch = sam9263ek_transceiver_switch,
+ * };
+ *
+ * at91_add_device_can(&ek_can_data);
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/errno.h>
+#include <linux/if_arp.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/platform_device.h>
+#include <linux/skbuff.h>
+#include <linux/spinlock.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+
+#include <mach/board.h>
+
+#define DRV_NAME "at91_can"
+#define AT91_NAPI_WEIGHT 12
+
+/*
+ * RX/TX Mailbox split
+ * don't dare to touch
+ */
+#define AT91_MB_RX_NUM 12
+#define AT91_MB_TX_SHIFT 2
+
+#define AT91_MB_RX_FIRST 0
+#define AT91_MB_RX_LAST (AT91_MB_RX_FIRST + AT91_MB_RX_NUM - 1)
+
+#define AT91_MB_RX_MASK(i) ((1 << (i)) - 1)
+#define AT91_MB_RX_SPLIT 8
+#define AT91_MB_RX_LOW_LAST (AT91_MB_RX_SPLIT - 1)
+#define AT91_MB_RX_LOW_MASK (AT91_MB_RX_MASK(AT91_MB_RX_SPLIT))
+
+#define AT91_MB_TX_NUM (1 << AT91_MB_TX_SHIFT)
+#define AT91_MB_TX_FIRST (AT91_MB_RX_LAST + 1)
+#define AT91_MB_TX_LAST (AT91_MB_TX_FIRST + AT91_MB_TX_NUM - 1)
+
+#define AT91_NEXT_PRIO_SHIFT (AT91_MB_TX_SHIFT)
+#define AT91_NEXT_PRIO_MASK (0xf << AT91_MB_TX_SHIFT)
+#define AT91_NEXT_MB_MASK (AT91_MB_TX_NUM - 1)
+#define AT91_NEXT_MASK ((AT91_MB_TX_NUM - 1) | AT91_NEXT_PRIO_MASK)
+
+/* Common registers */
+enum at91_reg {
+ AT91_MR = 0x000,
+ AT91_IER = 0x004,
+ AT91_IDR = 0x008,
+ AT91_IMR = 0x00C,
+ AT91_SR = 0x010,
+ AT91_BR = 0x014,
+ AT91_TIM = 0x018,
+ AT91_TIMESTP = 0x01C,
+ AT91_ECR = 0x020,
+ AT91_TCR = 0x024,
+ AT91_ACR = 0x028,
+};
+
+/* Mailbox registers (0 <= i <= 15) */
+#define AT91_MMR(i) (enum at91_reg)(0x200 + ((i) * 0x20))
+#define AT91_MAM(i) (enum at91_reg)(0x204 + ((i) * 0x20))
+#define AT91_MID(i) (enum at91_reg)(0x208 + ((i) * 0x20))
+#define AT91_MFID(i) (enum at91_reg)(0x20C + ((i) * 0x20))
+#define AT91_MSR(i) (enum at91_reg)(0x210 + ((i) * 0x20))
+#define AT91_MDL(i) (enum at91_reg)(0x214 + ((i) * 0x20))
+#define AT91_MDH(i) (enum at91_reg)(0x218 + ((i) * 0x20))
+#define AT91_MCR(i) (enum at91_reg)(0x21C + ((i) * 0x20))
+
+/* Register bits */
+#define AT91_MR_CANEN BIT(0)
+#define AT91_MR_LPM BIT(1)
+#define AT91_MR_ABM BIT(2)
+#define AT91_MR_OVL BIT(3)
+#define AT91_MR_TEOF BIT(4)
+#define AT91_MR_TTM BIT(5)
+#define AT91_MR_TIMFRZ BIT(6)
+#define AT91_MR_DRPT BIT(7)
+
+#define AT91_SR_RBSY BIT(29)
+
+#define AT91_MMR_PRIO_SHIFT (16)
+
+#define AT91_MID_MIDE BIT(29)
+
+#define AT91_MSR_MRTR BIT(20)
+#define AT91_MSR_MABT BIT(22)
+#define AT91_MSR_MRDY BIT(23)
+#define AT91_MSR_MMI BIT(24)
+
+#define AT91_MCR_MRTR BIT(20)
+#define AT91_MCR_MTCR BIT(23)
+
+/* Mailbox Modes */
+enum at91_mb_mode {
+ AT91_MB_MODE_DISABLED = 0,
+ AT91_MB_MODE_RX = 1,
+ AT91_MB_MODE_RX_OVRWR = 2,
+ AT91_MB_MODE_TX = 3,
+ AT91_MB_MODE_CONSUMER = 4,
+ AT91_MB_MODE_PRODUCER = 5,
+};
+
+/* Interrupt mask bits */
+#define AT91_IRQ_MB_RX ((1 << (AT91_MB_RX_LAST + 1)) \
+ - (1 << AT91_MB_RX_FIRST))
+#define AT91_IRQ_MB_TX ((1 << (AT91_MB_TX_LAST + 1)) \
+ - (1 << AT91_MB_TX_FIRST))
+#define AT91_IRQ_MB_ALL (AT91_IRQ_MB_RX | AT91_IRQ_MB_TX)
+
+#define AT91_IRQ_ERRA (1 << 16)
+#define AT91_IRQ_WARN (1 << 17)
+#define AT91_IRQ_ERRP (1 << 18)
+#define AT91_IRQ_BOFF (1 << 19)
+#define AT91_IRQ_SLEEP (1 << 20)
+#define AT91_IRQ_WAKEUP (1 << 21)
+#define AT91_IRQ_TOVF (1 << 22)
+#define AT91_IRQ_TSTP (1 << 23)
+#define AT91_IRQ_CERR (1 << 24)
+#define AT91_IRQ_SERR (1 << 25)
+#define AT91_IRQ_AERR (1 << 26)
+#define AT91_IRQ_FERR (1 << 27)
+#define AT91_IRQ_BERR (1 << 28)
+
+#define AT91_IRQ_ERR_ALL (0x1fff0000)
+#define AT91_IRQ_ERR_FRAME (AT91_IRQ_CERR | AT91_IRQ_SERR | \
+ AT91_IRQ_AERR | AT91_IRQ_FERR | AT91_IRQ_BERR)
+#define AT91_IRQ_ERR_LINE (AT91_IRQ_ERRA | AT91_IRQ_WARN | \
+ AT91_IRQ_ERRP | AT91_IRQ_BOFF)
+
+#define AT91_IRQ_ALL (0x1fffffff)
+
+struct at91_priv {
+ struct can_priv can; /* must be the first member! */
+ struct net_device *dev;
+ struct napi_struct napi;
+
+ void __iomem *reg_base;
+
+ u32 reg_sr;
+ unsigned int tx_next;
+ unsigned int tx_echo;
+ unsigned int rx_next;
+
+ struct clk *clk;
+ struct at91_can_data *pdata;
+};
+
+static struct can_bittiming_const at91_bittiming_const = {
+ .tseg1_min = 4,
+ .tseg1_max = 16,
+ .tseg2_min = 2,
+ .tseg2_max = 8,
+ .sjw_max = 4,
+ .brp_min = 2,
+ .brp_max = 128,
+ .brp_inc = 1,
+};
+
+static inline int get_tx_next_mb(const struct at91_priv *priv)
+{
+ return (priv->tx_next & AT91_NEXT_MB_MASK) + AT91_MB_TX_FIRST;
+}
+
+static inline int get_tx_next_prio(const struct at91_priv *priv)
+{
+ return (priv->tx_next >> AT91_NEXT_PRIO_SHIFT) & 0xf;
+}
+
+static inline int get_tx_echo_mb(const struct at91_priv *priv)
+{
+ return (priv->tx_echo & AT91_NEXT_MB_MASK) + AT91_MB_TX_FIRST;
+}
+
+static inline u32 at91_read(const struct at91_priv *priv, enum at91_reg reg)
+{
+ return readl(priv->reg_base + reg);
+}
+
+static inline void at91_write(const struct at91_priv *priv, enum at91_reg reg,
+ u32 value)
+{
+ writel(value, priv->reg_base + reg);
+}
+
+static inline void set_mb_mode_prio(const struct at91_priv *priv,
+ unsigned int mb, enum at91_mb_mode mode, int prio)
+{
+ at91_write(priv, AT91_MMR(mb), (mode << 24) | (prio << 16));
+}
+
+static inline void set_mb_mode(const struct at91_priv *priv, unsigned int mb,
+ enum at91_mb_mode mode)
+{
+ set_mb_mode_prio(priv, mb, mode, 0);
+}
+
+static struct sk_buff *alloc_can_skb(struct net_device *dev,
+ struct can_frame **cf)
+{
+ struct sk_buff *skb;
+
+ skb = netdev_alloc_skb(dev, sizeof(struct can_frame));
+ if (unlikely(!skb))
+ return NULL;
+
+ skb->protocol = htons(ETH_P_CAN);
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+ *cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
+
+ return skb;
+}
+
+static struct sk_buff *alloc_can_err_skb(struct net_device *dev,
+ struct can_frame **cf)
+{
+ struct sk_buff *skb;
+
+ skb = alloc_can_skb(dev, cf);
+ if (unlikely(!skb))
+ return NULL;
+
+ memset(*cf, 0, sizeof(struct can_frame));
+ (*cf)->can_id = CAN_ERR_FLAG;
+ (*cf)->can_dlc = CAN_ERR_DLC;
+
+ return skb;
+}
+
+/*
+ * Swtich transceiver on or off
+ */
+static void at91_transceiver_switch(const struct at91_priv *priv, int on)
+{
+ if (priv->pdata && priv->pdata->transceiver_switch)
+ priv->pdata->transceiver_switch(on);
+}
+
+static void at91_setup_mailboxes(struct net_device *dev)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ unsigned int i;
+
+ /*
+ * The first 12 mailboxes are used as a reception FIFO. The
+ * last mailbox is configured with overwrite option. The
+ * overwrite flag indicates a FIFO overflow.
+ */
+ for (i = AT91_MB_RX_FIRST; i < AT91_MB_RX_LAST; i++)
+ set_mb_mode(priv, i, AT91_MB_MODE_RX);
+ set_mb_mode(priv, AT91_MB_RX_LAST, AT91_MB_MODE_RX_OVRWR);
+
+ /* The last 4 mailboxes are used for transmitting. */
+ for (i = AT91_MB_TX_FIRST; i <= AT91_MB_TX_LAST; i++)
+ set_mb_mode_prio(priv, i, AT91_MB_MODE_TX, 0);
+
+ /* Reset tx and rx helper pointers */
+ priv->tx_next = priv->tx_echo = priv->rx_next = 0;
+}
+
+static int at91_set_bittiming(struct net_device *dev)
+{
+ const struct at91_priv *priv = netdev_priv(dev);
+ const struct can_bittiming *bt = &priv->can.bittiming;
+ u32 reg_br;
+
+ reg_br = ((priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) << 24) |
+ ((bt->brp - 1) << 16) | ((bt->sjw - 1) << 12) |
+ ((bt->prop_seg - 1) << 8) | ((bt->phase_seg1 - 1) << 4) |
+ ((bt->phase_seg2 - 1) << 0);
+
+ dev_info(dev->dev.parent, "writing AT91_BR: 0x%08x\n", reg_br);
+
+ at91_write(priv, AT91_BR, reg_br);
+
+ return 0;
+}
+
+static void at91_chip_start(struct net_device *dev)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_mr, reg_ier;
+
+ /* disable interrupts */
+ at91_write(priv, AT91_IDR, AT91_IRQ_ALL);
+
+ /* disable chip */
+ reg_mr = at91_read(priv, AT91_MR);
+ at91_write(priv, AT91_MR, reg_mr & ~AT91_MR_CANEN);
+
+ at91_setup_mailboxes(dev);
+ at91_transceiver_switch(priv, 1);
+
+ /* enable chip */
+ at91_write(priv, AT91_MR, AT91_MR_CANEN);
+
+ priv->can.state = CAN_STATE_ERROR_ACTIVE;
+
+ /* Enable interrupts */
+ reg_ier = AT91_IRQ_MB_RX | AT91_IRQ_ERRP | AT91_IRQ_ERR_FRAME;
+ at91_write(priv, AT91_IDR, AT91_IRQ_ALL);
+ at91_write(priv, AT91_IER, reg_ier);
+}
+
+static void at91_chip_stop(struct net_device *dev, enum can_state state)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_mr;
+
+ /* disable interrupts */
+ at91_write(priv, AT91_IDR, AT91_IRQ_ALL);
+
+ reg_mr = at91_read(priv, AT91_MR);
+ at91_write(priv, AT91_MR, reg_mr & ~AT91_MR_CANEN);
+
+ at91_transceiver_switch(priv, 0);
+ priv->can.state = state;
+}
+
+/*
+ * theory of operation:
+ *
+ * According to the datasheet priority 0 is the highest priority, 15
+ * is the lowest. If two mailboxes have the same priority level the
+ * message of the mailbox with the lowest number is sent first.
+ *
+ * We use the first TX mailbox (AT91_MB_TX_FIRST) with prio 0, then
+ * the next mailbox with prio 0, and so on, until all mailboxes are
+ * used. Then we start from the beginning with mailbox
+ * AT91_MB_TX_FIRST, but with prio 1, mailbox AT91_MB_TX_FIRST + 1
+ * prio 1. When we reach the last mailbox with prio 15, we have to
+ * stop sending, waiting for all messages to be delivered, then start
+ * again with mailbox AT91_MB_TX_FIRST prio 0.
+ *
+ * We use the priv->tx_next as counter for the next transmission
+ * mailbox, but without the offset AT91_MB_TX_FIRST. The lower bits
+ * encode the mailbox number, the upper 4 bits the mailbox priority:
+ *
+ * priv->tx_next = (prio << AT91_NEXT_PRIO_SHIFT) ||
+ * (mb - AT91_MB_TX_FIRST);
+ *
+ */
+static netdev_tx_t at91_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ struct net_device_stats *stats = &dev->stats;
+ struct can_frame *cf = (struct can_frame *)skb->data;
+ unsigned int mb, prio;
+ u32 reg_mid, reg_mcr;
+
+ mb = get_tx_next_mb(priv);
+ prio = get_tx_next_prio(priv);
+
+ if (unlikely(!(at91_read(priv, AT91_MSR(mb)) & AT91_MSR_MRDY))) {
+ netif_stop_queue(dev);
+
+ dev_err(dev->dev.parent,
+ "BUG! TX buffer full when queue awake!\n");
+ return NETDEV_TX_BUSY;
+ }
+
+ if (cf->can_id & CAN_EFF_FLAG)
+ reg_mid = (cf->can_id & CAN_EFF_MASK) | AT91_MID_MIDE;
+ else
+ reg_mid = (cf->can_id & CAN_SFF_MASK) << 18;
+
+ reg_mcr = ((cf->can_id & CAN_RTR_FLAG) ? AT91_MCR_MRTR : 0) |
+ (cf->can_dlc << 16) | AT91_MCR_MTCR;
+
+ /* disable MB while writing ID (see datasheet) */
+ set_mb_mode(priv, mb, AT91_MB_MODE_DISABLED);
+ at91_write(priv, AT91_MID(mb), reg_mid);
+ set_mb_mode_prio(priv, mb, AT91_MB_MODE_TX, prio);
+
+ at91_write(priv, AT91_MDL(mb), *(u32 *)(cf->data + 0));
+ at91_write(priv, AT91_MDH(mb), *(u32 *)(cf->data + 4));
+
+ /* This triggers transmission */
+ at91_write(priv, AT91_MCR(mb), reg_mcr);
+
+ stats->tx_bytes += cf->can_dlc;
+ dev->trans_start = jiffies;
+
+ /* _NOTE_: substract AT91_MB_TX_FIRST offset from mb! */
+ can_put_echo_skb(skb, dev, mb - AT91_MB_TX_FIRST);
+
+ /*
+ * we have to stop the queue and deliver all messages in case
+ * of a prio+mb counter wrap around. This is the case if
+ * tx_next buffer prio and mailbox equals 0.
+ *
+ * also stop the queue if next buffer is still in use
+ * (== not ready)
+ */
+ priv->tx_next++;
+ if (!(at91_read(priv, AT91_MSR(get_tx_next_mb(priv))) &
+ AT91_MSR_MRDY) ||
+ (priv->tx_next & AT91_NEXT_MASK) == 0)
+ netif_stop_queue(dev);
+
+ /* Enable interrupt for this mailbox */
+ at91_write(priv, AT91_IER, 1 << mb);
+
+ return NETDEV_TX_OK;
+}
+
+/**
+ * at91_activate_rx_low - activate lower rx mailboxes
+ * @priv: a91 context
+ *
+ * Reenables the lower mailboxes for reception of new CAN messages
+ */
+static inline void at91_activate_rx_low(const struct at91_priv *priv)
+{
+ u32 mask = AT91_MB_RX_LOW_MASK;
+ at91_write(priv, AT91_TCR, mask);
+}
+
+/**
+ * at91_activate_rx_mb - reactive single rx mailbox
+ * @priv: a91 context
+ * @mb: mailbox to reactivate
+ *
+ * Reenables given mailbox for reception of new CAN messages
+ */
+static inline void at91_activate_rx_mb(const struct at91_priv *priv,
+ unsigned int mb)
+{
+ u32 mask = 1 << mb;
+ at91_write(priv, AT91_TCR, mask);
+}
+
+/**
+ * at91_rx_overflow_err - send error frame due to rx overflow
+ * @dev: net device
+ */
+static void at91_rx_overflow_err(struct net_device *dev)
+{
+ struct net_device_stats *stats = &dev->stats;
+ struct sk_buff *skb;
+ struct can_frame *cf;
+
+ dev_dbg(dev->dev.parent, "RX buffer overflow\n");
+ stats->rx_over_errors++;
+ stats->rx_errors++;
+
+ skb = alloc_can_err_skb(dev, &cf);
+ if (unlikely(!skb))
+ return;
+
+ cf->can_id |= CAN_ERR_CRTL;
+ cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+ netif_receive_skb(skb);
+
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+}
+
+/**
+ * at91_read_mb - read CAN msg from mailbox (lowlevel impl)
+ * @dev: net device
+ * @mb: mailbox number to read from
+ * @cf: can frame where to store message
+ *
+ * Reads a CAN message from the given mailbox and stores data into
+ * given can frame. "mb" and "cf" must be valid.
+ */
+static void at91_read_mb(struct net_device *dev, unsigned int mb,
+ struct can_frame *cf)
+{
+ const struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_msr, reg_mid;
+
+ reg_mid = at91_read(priv, AT91_MID(mb));
+ if (reg_mid & AT91_MID_MIDE)
+ cf->can_id = ((reg_mid >> 0) & CAN_EFF_MASK) | CAN_EFF_FLAG;
+ else
+ cf->can_id = (reg_mid >> 18) & CAN_SFF_MASK;
+
+ reg_msr = at91_read(priv, AT91_MSR(mb));
+ if (reg_msr & AT91_MSR_MRTR)
+ cf->can_id |= CAN_RTR_FLAG;
+ cf->can_dlc = min_t(__u8, (reg_msr >> 16) & 0xf, 8);
+
+ *(u32 *)(cf->data + 0) = at91_read(priv, AT91_MDL(mb));
+ *(u32 *)(cf->data + 4) = at91_read(priv, AT91_MDH(mb));
+
+ if (unlikely(mb == AT91_MB_RX_LAST && reg_msr & AT91_MSR_MMI))
+ at91_rx_overflow_err(dev);
+}
+
+/**
+ * at91_read_msg - read CAN message from mailbox
+ * @dev: net device
+ * @mb: mail box to read from
+ *
+ * Reads a CAN message from given mailbox, and put into linux network
+ * RX queue, does all housekeeping chores (stats, ...)
+ */
+static void at91_read_msg(struct net_device *dev, unsigned int mb)
+{
+ struct net_device_stats *stats = &dev->stats;
+ struct can_frame *cf;
+ struct sk_buff *skb;
+
+ skb = alloc_can_skb(dev, &cf);
+ if (unlikely(!skb)) {
+ stats->rx_dropped++;
+ return;
+ }
+
+ at91_read_mb(dev, mb, cf);
+ netif_receive_skb(skb);
+
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+}
+
+/**
+ * at91_poll_rx - read multiple CAN messages from mailboxes
+ * @dev: net device
+ * @quota: max number of pkgs we're allowed to receive
+ *
+ * Theory of Operation:
+ *
+ * 12 of the 16 mailboxes on the chip are reserved for RX. we split
+ * them into 2 groups. The lower group holds 8 and upper 4 mailboxes.
+ *
+ * Like it or not, but the chip always saves a received CAN message
+ * into the first free mailbox it finds (starting with the
+ * lowest). This makes it very difficult to read the messages in the
+ * right order from the chip. This is how we work around that problem:
+ *
+ * The first message goes into mb nr. 0 and issues an interrupt. All
+ * rx ints are disabled in the interrupt handler and a napi poll is
+ * scheduled. We read the mailbox, but do _not_ reenable the mb (to
+ * receive another message).
+ *
+ * lower mbxs upper
+ * ______^______ __^__
+ * / \ / \
+ * +-+-+-+-+-+-+-+-++-+-+-+-+
+ * |x|x|x|x|x|x|x|x|| | | | |
+ * +-+-+-+-+-+-+-+-++-+-+-+-+
+ * 0 0 0 0 0 0 0 0 0 0 1 1 \ mail
+ * 0 1 2 3 4 5 6 7 8 9 0 1 / box
+ *
+ * The variable priv->rx_next points to the next mailbox to read a
+ * message from. As long we're in the lower mailboxes we just read the
+ * mailbox but not reenable it.
+ *
+ * With completion of the last of the lower mailboxes, we reenable the
+ * whole first group, but continue to look for filled mailboxes in the
+ * upper mailboxes. Imagine the second group like overflow mailboxes,
+ * which takes CAN messages if the lower goup is full. While in the
+ * upper group we reenable the mailbox right after reading it. Giving
+ * the chip more room to store messages.
+ *
+ * After finishing we look again in the lower group if we've still
+ * quota.
+ *
+ */
+static int at91_poll_rx(struct net_device *dev, int quota)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_sr = at91_read(priv, AT91_SR);
+ const unsigned long *addr = (unsigned long *)®_sr;
+ unsigned int mb;
+ int received = 0;
+
+ if (priv->rx_next > AT91_MB_RX_LOW_LAST &&
+ reg_sr & AT91_MB_RX_LOW_MASK)
+ dev_info(dev->dev.parent,
+ "order of incoming frames cannot be guaranteed\n");
+
+ again:
+ for (mb = find_next_bit(addr, AT91_MB_RX_NUM, priv->rx_next);
+ mb < AT91_MB_RX_NUM && quota > 0;
+ reg_sr = at91_read(priv, AT91_SR),
+ mb = find_next_bit(addr, AT91_MB_RX_NUM, ++priv->rx_next)) {
+ at91_read_msg(dev, mb);
+
+ /* reactivate mailboxes */
+ if (mb == AT91_MB_RX_LOW_LAST)
+ /* all lower mailboxed, if just finished it */
+ at91_activate_rx_low(priv);
+ else if (mb > AT91_MB_RX_LOW_LAST)
+ /* only the mailbox we read */
+ at91_activate_rx_mb(priv, mb);
+
+ received++;
+ quota--;
+ }
+
+ /* upper group completed, look again in lower */
+ if (priv->rx_next > AT91_MB_RX_LOW_LAST &&
+ quota > 0 && mb >= AT91_MB_RX_NUM) {
+ priv->rx_next = 0;
+ goto again;
+ }
+
+ return received;
+}
+
+static void at91_poll_err_frame(struct net_device *dev,
+ struct can_frame *cf, u32 reg_sr)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+
+ /* CRC error */
+ if (reg_sr & AT91_IRQ_CERR) {
+ dev_dbg(dev->dev.parent, "CERR irq\n");
+ dev->stats.rx_errors++;
+ priv->can.can_stats.bus_error++;
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+ }
+
+ /* Stuffing Error */
+ if (reg_sr & AT91_IRQ_SERR) {
+ dev_dbg(dev->dev.parent, "SERR irq\n");
+ dev->stats.rx_errors++;
+ priv->can.can_stats.bus_error++;
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+ cf->data[2] |= CAN_ERR_PROT_STUFF;
+ }
+
+ /* Acknowledgement Error */
+ if (reg_sr & AT91_IRQ_AERR) {
+ dev_dbg(dev->dev.parent, "AERR irq\n");
+ dev->stats.tx_errors++;
+ cf->can_id |= CAN_ERR_ACK;
+ }
+
+ /* Form error */
+ if (reg_sr & AT91_IRQ_FERR) {
+ dev_dbg(dev->dev.parent, "FERR irq\n");
+ dev->stats.rx_errors++;
+ priv->can.can_stats.bus_error++;
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+ cf->data[2] |= CAN_ERR_PROT_FORM;
+ }
+
+ /* Bit Error */
+ if (reg_sr & AT91_IRQ_BERR) {
+ dev_dbg(dev->dev.parent, "BERR irq\n");
+ dev->stats.tx_errors++;
+ priv->can.can_stats.bus_error++;
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+ cf->data[2] |= CAN_ERR_PROT_BIT;
+ }
+}
+
+static int at91_poll_err(struct net_device *dev, int quota, u32 reg_sr)
+{
+ struct sk_buff *skb;
+ struct can_frame *cf;
+
+ if (quota == 0)
+ return 0;
+
+ skb = alloc_can_err_skb(dev, &cf);
+ if (unlikely(!skb))
+ return 0;
+
+ at91_poll_err_frame(dev, cf, reg_sr);
+ netif_receive_skb(skb);
+
+ dev->last_rx = jiffies;
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += cf->can_dlc;
+
+ return 1;
+}
+
+static int at91_poll(struct napi_struct *napi, int quota)
+{
+ struct net_device *dev = napi->dev;
+ const struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_sr = at91_read(priv, AT91_SR);
+ int work_done = 0;
+
+ if (reg_sr & AT91_IRQ_MB_RX)
+ work_done += at91_poll_rx(dev, quota - work_done);
+
+ /*
+ * The error bits are clear on read,
+ * so use saved value from irq handler.
+ */
+ reg_sr |= priv->reg_sr;
+ if (reg_sr & AT91_IRQ_ERR_FRAME)
+ work_done += at91_poll_err(dev, quota - work_done, reg_sr);
+
+ if (work_done < quota) {
+ /* enable IRQs for frame errors and all mailboxes >= rx_next */
+ u32 reg_ier = AT91_IRQ_ERR_FRAME;
+ reg_ier |= AT91_IRQ_MB_RX & ~AT91_MB_RX_MASK(priv->rx_next);
+
+ napi_complete(napi);
+ at91_write(priv, AT91_IER, reg_ier);
+ }
+
+ return work_done;
+}
+
+/*
+ * theory of operation:
+ *
+ * priv->tx_echo holds the number of the oldest can_frame put for
+ * transmission into the hardware, but not yet ACKed by the CAN tx
+ * complete IRQ.
+ *
+ * We iterate from priv->tx_echo to priv->tx_next and check if the
+ * packet has been transmitted, echo it back to the CAN framework. If
+ * we discover a not yet transmitted package, stop looking for more.
+ *
+ */
+static void at91_irq_tx(struct net_device *dev, u32 reg_sr)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_msr;
+ unsigned int mb;
+
+ /* masking of reg_sr not needed, already done by at91_irq */
+
+ for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) {
+ mb = get_tx_echo_mb(priv);
+
+ /* no event in mailbox? */
+ if (!(reg_sr & (1 << mb)))
+ break;
+
+ /* Disable irq for this TX mailbox */
+ at91_write(priv, AT91_IDR, 1 << mb);
+
+ /*
+ * only echo if mailbox signals us a transfer
+ * complete (MSR_MRDY). Otherwise it's a tansfer
+ * abort. "can_bus_off()" takes care about the skbs
+ * parked in the echo queue.
+ */
+ reg_msr = at91_read(priv, AT91_MSR(mb));
+ if (likely(reg_msr & AT91_MSR_MRDY &&
+ ~reg_msr & AT91_MSR_MABT)) {
+ /* _NOTE_: substract AT91_MB_TX_FIRST offset from mb! */
+ can_get_echo_skb(dev, mb - AT91_MB_TX_FIRST);
+ dev->stats.tx_packets++;
+ }
+ }
+
+ /*
+ * restart queue if we don't have a wrap around but restart if
+ * we get a TX int for the last can frame directly before a
+ * wrap around.
+ */
+ if ((priv->tx_next & AT91_NEXT_MASK) != 0 ||
+ (priv->tx_echo & AT91_NEXT_MASK) == 0)
+ netif_wake_queue(dev);
+}
+
+static void at91_irq_err_state(struct net_device *dev,
+ struct can_frame *cf, enum can_state new_state)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ u32 reg_idr, reg_ier, reg_ecr;
+ u8 tec, rec;
+
+ reg_ecr = at91_read(priv, AT91_ECR);
+ rec = reg_ecr & 0xff;
+ tec = reg_ecr >> 16;
+
+ switch (priv->can.state) {
+ case CAN_STATE_ERROR_ACTIVE:
+ /*
+ * from: ERROR_ACTIVE
+ * to : ERROR_WARNING, ERROR_PASSIVE, BUS_OFF
+ * => : there was a warning int
+ */
+ if (new_state >= CAN_STATE_ERROR_WARNING &&
+ new_state <= CAN_STATE_BUS_OFF) {
+ dev_dbg(dev->dev.parent, "Error Warning IRQ\n");
+ priv->can.can_stats.error_warning++;
+
+ cf->can_id |= CAN_ERR_CRTL;
+ cf->data[1] = (tec > rec) ?
+ CAN_ERR_CRTL_TX_WARNING :
+ CAN_ERR_CRTL_RX_WARNING;
+ }
+ case CAN_STATE_ERROR_WARNING: /* fallthrough */
+ /*
+ * from: ERROR_ACTIVE, ERROR_WARNING
+ * to : ERROR_PASSIVE, BUS_OFF
+ * => : error passive int
+ */
+ if (new_state >= CAN_STATE_ERROR_PASSIVE &&
+ new_state <= CAN_STATE_BUS_OFF) {
+ dev_dbg(dev->dev.parent, "Error Passive IRQ\n");
+ priv->can.can_stats.error_passive++;
+
+ cf->can_id |= CAN_ERR_CRTL;
+ cf->data[1] = (tec > rec) ?
+ CAN_ERR_CRTL_TX_PASSIVE :
+ CAN_ERR_CRTL_RX_PASSIVE;
+ }
+ break;
+ case CAN_STATE_BUS_OFF:
+ /*
+ * from: BUS_OFF
+ * to : ERROR_ACTIVE, ERROR_WARNING, ERROR_PASSIVE
+ */
+ if (new_state <= CAN_STATE_ERROR_PASSIVE) {
+ cf->can_id |= CAN_ERR_RESTARTED;
+
+ dev_dbg(dev->dev.parent, "restarted\n");
+ priv->can.can_stats.restarts++;
+
+ netif_carrier_on(dev);
+ netif_wake_queue(dev);
+ }
+ break;
+ default:
+ break;
+ }
+
+
+ /* process state changes depending on the new state */
+ switch (new_state) {
+ case CAN_STATE_ERROR_ACTIVE:
+ /*
+ * actually we want to enable AT91_IRQ_WARN here, but
+ * it screws up the system under certain
+ * circumstances. so just enable AT91_IRQ_ERRP, thus
+ * the "fallthrough"
+ */
+ dev_dbg(dev->dev.parent, "Error Active\n");
+ cf->can_id |= CAN_ERR_PROT;
+ cf->data[2] = CAN_ERR_PROT_ACTIVE;
+ case CAN_STATE_ERROR_WARNING: /* fallthrough */
+ reg_idr = AT91_IRQ_ERRA | AT91_IRQ_WARN | AT91_IRQ_BOFF;
+ reg_ier = AT91_IRQ_ERRP;
+ break;
+ case CAN_STATE_ERROR_PASSIVE:
+ reg_idr = AT91_IRQ_ERRA | AT91_IRQ_WARN | AT91_IRQ_ERRP;
+ reg_ier = AT91_IRQ_BOFF;
+ break;
+ case CAN_STATE_BUS_OFF:
+ reg_idr = AT91_IRQ_ERRA | AT91_IRQ_ERRP |
+ AT91_IRQ_WARN | AT91_IRQ_BOFF;
+ reg_ier = 0;
+
+ cf->can_id |= CAN_ERR_BUSOFF;
+
+ dev_dbg(dev->dev.parent, "bus-off\n");
+ netif_carrier_off(dev);
+ priv->can.can_stats.bus_off++;
+
+ /* turn off chip, if restart is disabled */
+ if (!priv->can.restart_ms) {
+ at91_chip_stop(dev, CAN_STATE_BUS_OFF);
+ return;
+ }
+ break;
+ default:
+ break;
+ }
+
+ at91_write(priv, AT91_IDR, reg_idr);
+ at91_write(priv, AT91_IER, reg_ier);
+}
+
+static void at91_irq_err(struct net_device *dev)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ struct sk_buff *skb;
+ struct can_frame *cf;
+ enum can_state new_state;
+ u32 reg_sr;
+
+ reg_sr = at91_read(priv, AT91_SR);
+
+ /* we need to look at the unmasked reg_sr */
+ if (unlikely(reg_sr & AT91_IRQ_BOFF))
+ new_state = CAN_STATE_BUS_OFF;
+ else if (unlikely(reg_sr & AT91_IRQ_ERRP))
+ new_state = CAN_STATE_ERROR_PASSIVE;
+ else if (unlikely(reg_sr & AT91_IRQ_WARN))
+ new_state = CAN_STATE_ERROR_WARNING;
+ else if (likely(reg_sr & AT91_IRQ_ERRA))
+ new_state = CAN_STATE_ERROR_ACTIVE;
+ else {
+ dev_err(dev->dev.parent, "BUG! hardware in undefined state\n");
+ return;
+ }
+
+ /* state hasn't changed */
+ if (likely(new_state == priv->can.state))
+ return;
+
+ skb = alloc_can_err_skb(dev, &cf);
+ if (unlikely(!skb))
+ return;
+
+ at91_irq_err_state(dev, cf, new_state);
+ netif_rx(skb);
+
+ dev->last_rx = jiffies;
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += cf->can_dlc;
+
+ priv->can.state = new_state;
+}
+
+/*
+ * interrupt handler
+ */
+static irqreturn_t at91_irq(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct at91_priv *priv = netdev_priv(dev);
+ irqreturn_t handled = IRQ_NONE;
+ u32 reg_sr, reg_imr;
+
+ reg_sr = at91_read(priv, AT91_SR);
+ reg_imr = at91_read(priv, AT91_IMR);
+
+ /* Ignore masked interrupts */
+ reg_sr &= reg_imr;
+ if (!reg_sr)
+ goto exit;
+
+ handled = IRQ_HANDLED;
+
+ /* Receive or error interrupt? -> napi */
+ if (reg_sr & (AT91_IRQ_MB_RX | AT91_IRQ_ERR_FRAME)) {
+ /*
+ * The error bits are clear on read,
+ * save for later use.
+ */
+ priv->reg_sr = reg_sr;
+ at91_write(priv, AT91_IDR,
+ AT91_IRQ_MB_RX | AT91_IRQ_ERR_FRAME);
+ napi_schedule(&priv->napi);
+ }
+
+ /* Transmission complete interrupt */
+ if (reg_sr & AT91_IRQ_MB_TX)
+ at91_irq_tx(dev, reg_sr);
+
+ at91_irq_err(dev);
+
+ exit:
+ return handled;
+}
+
+static int at91_open(struct net_device *dev)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+ int err;
+
+ clk_enable(priv->clk);
+
+ /* check or determine and set bittime */
+ err = open_candev(dev);
+ if (err)
+ goto out;
+
+ /* register interrupt handler */
+ if (request_irq(dev->irq, at91_irq, IRQF_SHARED,
+ dev->name, dev)) {
+ err = -EAGAIN;
+ goto out_close;
+ }
+
+ /* start chip and queuing */
+ at91_chip_start(dev);
+ napi_enable(&priv->napi);
+ netif_start_queue(dev);
+
+ return 0;
+
+ out_close:
+ close_candev(dev);
+ out:
+ clk_disable(priv->clk);
+
+ return err;
+}
+
+/*
+ * stop CAN bus activity
+ */
+static int at91_close(struct net_device *dev)
+{
+ struct at91_priv *priv = netdev_priv(dev);
+
+ netif_stop_queue(dev);
+ napi_disable(&priv->napi);
+ at91_chip_stop(dev, CAN_STATE_STOPPED);
+
+ free_irq(dev->irq, dev);
+ clk_disable(priv->clk);
+
+ close_candev(dev);
+
+ return 0;
+}
+
+static int at91_set_mode(struct net_device *dev, enum can_mode mode)
+{
+ switch (mode) {
+ case CAN_MODE_START:
+ at91_chip_start(dev);
+ netif_wake_queue(dev);
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ return 0;
+}
+
+static const struct net_device_ops at91_netdev_ops = {
+ .ndo_open = at91_open,
+ .ndo_stop = at91_close,
+ .ndo_start_xmit = at91_start_xmit,
+};
+
+static int __init at91_can_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct at91_priv *priv;
+ struct resource *res;
+ struct clk *clk;
+ void __iomem *addr;
+ int err, irq;
+
+ clk = clk_get(&pdev->dev, "can_clk");
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "no clock defined\n");
+ err = -ENODEV;
+ goto exit;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (!res || !irq) {
+ err = -ENODEV;
+ goto exit_put;
+ }
+
+ if (!request_mem_region(res->start,
+ resource_size(res),
+ pdev->name)) {
+ err = -EBUSY;
+ goto exit_put;
+ }
+
+ addr = ioremap_nocache(res->start, resource_size(res));
+ if (!addr) {
+ err = -ENOMEM;
+ goto exit_release;
+ }
+
+ dev = alloc_candev(sizeof(struct at91_priv));
+ if (!dev) {
+ err = -ENOMEM;
+ goto exit_iounmap;
+ }
+
+ dev->netdev_ops = &at91_netdev_ops;
+ dev->irq = irq;
+ dev->flags |= IFF_ECHO;
+
+ priv = netdev_priv(dev);
+ priv->can.clock.freq = clk_get_rate(clk);
+ priv->can.bittiming_const = &at91_bittiming_const;
+ priv->can.do_set_bittiming = at91_set_bittiming;
+ priv->can.do_set_mode = at91_set_mode;
+ priv->reg_base = addr;
+ priv->dev = dev;
+ priv->clk = clk;
+ priv->pdata = pdev->dev.platform_data;
+
+ netif_napi_add(dev, &priv->napi, at91_poll, AT91_NAPI_WEIGHT);
+
+ dev_set_drvdata(&pdev->dev, dev);
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+ err = register_candev(dev);
+ if (err) {
+ dev_err(&pdev->dev, "registering netdev failed\n");
+ goto exit_free;
+ }
+
+ dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n",
+ priv->reg_base, dev->irq);
+
+ return 0;
+
+ exit_free:
+ free_netdev(dev);
+ exit_iounmap:
+ iounmap(addr);
+ exit_release:
+ release_mem_region(res->start, resource_size(res));
+ exit_put:
+ clk_put(clk);
+ exit:
+ return err;
+}
+
+static int __devexit at91_can_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct at91_priv *priv = netdev_priv(dev);
+ struct resource *res;
+
+ unregister_netdev(dev);
+
+ platform_set_drvdata(pdev, NULL);
+
+ free_netdev(dev);
+
+ iounmap(priv->reg_base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(res->start, resource_size(res));
+
+ clk_put(priv->clk);
+
+ return 0;
+}
+
+static struct platform_driver at91_can_driver = {
+ .probe = at91_can_probe,
+ .remove = __devexit_p(at91_can_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init at91_can_module_init(void)
+{
+ printk(KERN_INFO "%s netdevice driver\n", DRV_NAME);
+ return platform_driver_register(&at91_can_driver);
+}
+
+static void __exit at91_can_module_exit(void)
+{
+ platform_driver_unregister(&at91_can_driver);
+ printk(KERN_INFO "%s: driver removed\n", DRV_NAME);
+}
+
+module_init(at91_can_module_init);
+module_exit(at91_can_module_exit);
+
+MODULE_AUTHOR("Marc Kleine-Budde <mkl@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION(DRV_NAME " CAN netdevice driver");
#define EMS_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK)
#define EMS_PCI_V1_BASE_BAR 1
-#define EMS_PCI_V1_MEM_SIZE 4096
+#define EMS_PCI_V1_CONF_SIZE 4096 /* size of PITA control area */
#define EMS_PCI_V2_BASE_BAR 2
-#define EMS_PCI_V2_MEM_SIZE 128
+#define EMS_PCI_V2_CONF_SIZE 128 /* size of PLX control area */
#define EMS_PCI_CAN_BASE_OFFSET 0x400 /* offset where the controllers starts */
#define EMS_PCI_CAN_CTRL_SIZE 0x200 /* memory size for each controller */
+#define EMS_PCI_BASE_SIZE 4096 /* size of controller area */
+
static struct pci_device_id ems_pci_tbl[] = {
/* CPC-PCI v1 */
{PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,},
struct sja1000_priv *priv;
struct net_device *dev;
struct ems_pci_card *card;
- int max_chan, mem_size, base_bar;
+ int max_chan, conf_size, base_bar;
int err, i;
/* Enabling PCI device */
card->version = 2; /* CPC-PCI v2 */
max_chan = EMS_PCI_V2_MAX_CHAN;
base_bar = EMS_PCI_V2_BASE_BAR;
- mem_size = EMS_PCI_V2_MEM_SIZE;
+ conf_size = EMS_PCI_V2_CONF_SIZE;
} else {
card->version = 1; /* CPC-PCI v1 */
max_chan = EMS_PCI_V1_MAX_CHAN;
base_bar = EMS_PCI_V1_BASE_BAR;
- mem_size = EMS_PCI_V1_MEM_SIZE;
+ conf_size = EMS_PCI_V1_CONF_SIZE;
}
/* Remap configuration space and controller memory area */
- card->conf_addr = pci_iomap(pdev, 0, mem_size);
+ card->conf_addr = pci_iomap(pdev, 0, conf_size);
if (card->conf_addr == NULL) {
err = -ENOMEM;
goto failure_cleanup;
}
- card->base_addr = pci_iomap(pdev, base_bar, mem_size);
+ card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE);
if (card->base_addr == NULL) {
err = -ENOMEM;
goto failure_cleanup;
--- /dev/null
+#
+# Makefile for the Linux Controller Area Network USB drivers.
+#
+
+obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o
--- /dev/null
+/*
+ * CAN driver for EMS Dr. Thomas Wuensche CPC-USB/ARM7
+ *
+ * Copyright (C) 2004-2009 EMS Dr. Thomas Wuensche
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published
+ * by the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+#include <linux/init.h>
+#include <linux/signal.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/usb.h>
+
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include <linux/can/error.h>
+
+MODULE_AUTHOR("Sebastian Haas <haas@ems-wuensche.com>");
+MODULE_DESCRIPTION("CAN driver for EMS Dr. Thomas Wuensche CAN/USB interfaces");
+MODULE_LICENSE("GPL v2");
+
+/* Control-Values for CPC_Control() Command Subject Selection */
+#define CONTR_CAN_MESSAGE 0x04
+#define CONTR_CAN_STATE 0x0C
+#define CONTR_BUS_ERROR 0x1C
+
+/* Control Command Actions */
+#define CONTR_CONT_OFF 0
+#define CONTR_CONT_ON 1
+#define CONTR_ONCE 2
+
+/* Messages from CPC to PC */
+#define CPC_MSG_TYPE_CAN_FRAME 1 /* CAN data frame */
+#define CPC_MSG_TYPE_RTR_FRAME 8 /* CAN remote frame */
+#define CPC_MSG_TYPE_CAN_PARAMS 12 /* Actual CAN parameters */
+#define CPC_MSG_TYPE_CAN_STATE 14 /* CAN state message */
+#define CPC_MSG_TYPE_EXT_CAN_FRAME 16 /* Extended CAN data frame */
+#define CPC_MSG_TYPE_EXT_RTR_FRAME 17 /* Extended remote frame */
+#define CPC_MSG_TYPE_CONTROL 19 /* change interface behavior */
+#define CPC_MSG_TYPE_CONFIRM 20 /* command processed confirmation */
+#define CPC_MSG_TYPE_OVERRUN 21 /* overrun events */
+#define CPC_MSG_TYPE_CAN_FRAME_ERROR 23 /* detected bus errors */
+#define CPC_MSG_TYPE_ERR_COUNTER 25 /* RX/TX error counter */
+
+/* Messages from the PC to the CPC interface */
+#define CPC_CMD_TYPE_CAN_FRAME 1 /* CAN data frame */
+#define CPC_CMD_TYPE_CONTROL 3 /* control of interface behavior */
+#define CPC_CMD_TYPE_CAN_PARAMS 6 /* set CAN parameters */
+#define CPC_CMD_TYPE_RTR_FRAME 13 /* CAN remote frame */
+#define CPC_CMD_TYPE_CAN_STATE 14 /* CAN state message */
+#define CPC_CMD_TYPE_EXT_CAN_FRAME 15 /* Extended CAN data frame */
+#define CPC_CMD_TYPE_EXT_RTR_FRAME 16 /* Extended CAN remote frame */
+#define CPC_CMD_TYPE_CAN_EXIT 200 /* exit the CAN */
+
+#define CPC_CMD_TYPE_INQ_ERR_COUNTER 25 /* request the CAN error counters */
+#define CPC_CMD_TYPE_CLEAR_MSG_QUEUE 8 /* clear CPC_MSG queue */
+#define CPC_CMD_TYPE_CLEAR_CMD_QUEUE 28 /* clear CPC_CMD queue */
+
+#define CPC_CC_TYPE_SJA1000 2 /* Philips basic CAN controller */
+
+#define CPC_CAN_ECODE_ERRFRAME 0x01 /* Ecode type */
+
+/* Overrun types */
+#define CPC_OVR_EVENT_CAN 0x01
+#define CPC_OVR_EVENT_CANSTATE 0x02
+#define CPC_OVR_EVENT_BUSERROR 0x04
+
+/*
+ * If the CAN controller lost a message we indicate it with the highest bit
+ * set in the count field.
+ */
+#define CPC_OVR_HW 0x80
+
+/* Size of the "struct ems_cpc_msg" without the union */
+#define CPC_MSG_HEADER_LEN 11
+#define CPC_CAN_MSG_MIN_SIZE 5
+
+/* Define these values to match your devices */
+#define USB_CPCUSB_VENDOR_ID 0x12D6
+
+#define USB_CPCUSB_ARM7_PRODUCT_ID 0x0444
+
+/* Mode register NXP LPC2119/SJA1000 CAN Controller */
+#define SJA1000_MOD_NORMAL 0x00
+#define SJA1000_MOD_RM 0x01
+
+/* ECC register NXP LPC2119/SJA1000 CAN Controller */
+#define SJA1000_ECC_SEG 0x1F
+#define SJA1000_ECC_DIR 0x20
+#define SJA1000_ECC_ERR 0x06
+#define SJA1000_ECC_BIT 0x00
+#define SJA1000_ECC_FORM 0x40
+#define SJA1000_ECC_STUFF 0x80
+#define SJA1000_ECC_MASK 0xc0
+
+/* Status register content */
+#define SJA1000_SR_BS 0x80
+#define SJA1000_SR_ES 0x40
+
+#define SJA1000_DEFAULT_OUTPUT_CONTROL 0xDA
+
+/*
+ * The device actually uses a 16MHz clock to generate the CAN clock
+ * but it expects SJA1000 bit settings based on 8MHz (is internally
+ * converted).
+ */
+#define EMS_USB_ARM7_CLOCK 8000000
+
+/*
+ * CAN-Message representation in a CPC_MSG. Message object type is
+ * CPC_MSG_TYPE_CAN_FRAME or CPC_MSG_TYPE_RTR_FRAME or
+ * CPC_MSG_TYPE_EXT_CAN_FRAME or CPC_MSG_TYPE_EXT_RTR_FRAME.
+ */
+struct cpc_can_msg {
+ u32 id;
+ u8 length;
+ u8 msg[8];
+};
+
+/* Representation of the CAN parameters for the SJA1000 controller */
+struct cpc_sja1000_params {
+ u8 mode;
+ u8 acc_code0;
+ u8 acc_code1;
+ u8 acc_code2;
+ u8 acc_code3;
+ u8 acc_mask0;
+ u8 acc_mask1;
+ u8 acc_mask2;
+ u8 acc_mask3;
+ u8 btr0;
+ u8 btr1;
+ u8 outp_contr;
+};
+
+/* CAN params message representation */
+struct cpc_can_params {
+ u8 cc_type;
+
+ /* Will support M16C CAN controller in the future */
+ union {
+ struct cpc_sja1000_params sja1000;
+ } cc_params;
+};
+
+/* Structure for confirmed message handling */
+struct cpc_confirm {
+ u8 error; /* error code */
+};
+
+/* Structure for overrun conditions */
+struct cpc_overrun {
+ u8 event;
+ u8 count;
+};
+
+/* SJA1000 CAN errors (compatible to NXP LPC2119) */
+struct cpc_sja1000_can_error {
+ u8 ecc;
+ u8 rxerr;
+ u8 txerr;
+};
+
+/* structure for CAN error conditions */
+struct cpc_can_error {
+ u8 ecode;
+
+ struct {
+ u8 cc_type;
+
+ /* Other controllers may also provide error code capture regs */
+ union {
+ struct cpc_sja1000_can_error sja1000;
+ } regs;
+ } cc;
+};
+
+/*
+ * Structure containing RX/TX error counter. This structure is used to request
+ * the values of the CAN controllers TX and RX error counter.
+ */
+struct cpc_can_err_counter {
+ u8 rx;
+ u8 tx;
+};
+
+/* Main message type used between library and application */
+struct __attribute__ ((packed)) ems_cpc_msg {
+ u8 type; /* type of message */
+ u8 length; /* length of data within union 'msg' */
+ u8 msgid; /* confirmation handle */
+ u32 ts_sec; /* timestamp in seconds */
+ u32 ts_nsec; /* timestamp in nano seconds */
+
+ union {
+ u8 generic[64];
+ struct cpc_can_msg can_msg;
+ struct cpc_can_params can_params;
+ struct cpc_confirm confirmation;
+ struct cpc_overrun overrun;
+ struct cpc_can_error error;
+ struct cpc_can_err_counter err_counter;
+ u8 can_state;
+ } msg;
+};
+
+/*
+ * Table of devices that work with this driver
+ * NOTE: This driver supports only CPC-USB/ARM7 (LPC2119) yet.
+ */
+static struct usb_device_id ems_usb_table[] = {
+ {USB_DEVICE(USB_CPCUSB_VENDOR_ID, USB_CPCUSB_ARM7_PRODUCT_ID)},
+ {} /* Terminating entry */
+};
+
+MODULE_DEVICE_TABLE(usb, ems_usb_table);
+
+#define RX_BUFFER_SIZE 64
+#define CPC_HEADER_SIZE 4
+#define INTR_IN_BUFFER_SIZE 4
+
+#define MAX_RX_URBS 10
+#define MAX_TX_URBS CAN_ECHO_SKB_MAX
+
+struct ems_usb;
+
+struct ems_tx_urb_context {
+ struct ems_usb *dev;
+
+ u32 echo_index;
+ u8 dlc;
+};
+
+struct ems_usb {
+ struct can_priv can; /* must be the first member */
+ int open_time;
+
+ struct sk_buff *echo_skb[MAX_TX_URBS];
+
+ struct usb_device *udev;
+ struct net_device *netdev;
+
+ atomic_t active_tx_urbs;
+ struct usb_anchor tx_submitted;
+ struct ems_tx_urb_context tx_contexts[MAX_TX_URBS];
+
+ struct usb_anchor rx_submitted;
+
+ struct urb *intr_urb;
+
+ u8 *tx_msg_buffer;
+
+ u8 *intr_in_buffer;
+ unsigned int free_slots; /* remember number of available slots */
+
+ struct ems_cpc_msg active_params; /* active controller parameters */
+};
+
+static void ems_usb_read_interrupt_callback(struct urb *urb)
+{
+ struct ems_usb *dev = urb->context;
+ struct net_device *netdev = dev->netdev;
+ int err;
+
+ if (!netif_device_present(netdev))
+ return;
+
+ switch (urb->status) {
+ case 0:
+ dev->free_slots = dev->intr_in_buffer[1];
+ break;
+
+ case -ECONNRESET: /* unlink */
+ case -ENOENT:
+ case -ESHUTDOWN:
+ return;
+
+ default:
+ dev_info(netdev->dev.parent, "Rx interrupt aborted %d\n",
+ urb->status);
+ break;
+ }
+
+ err = usb_submit_urb(urb, GFP_ATOMIC);
+
+ if (err == -ENODEV)
+ netif_device_detach(netdev);
+ else if (err)
+ dev_err(netdev->dev.parent,
+ "failed resubmitting intr urb: %d\n", err);
+
+ return;
+}
+
+static void ems_usb_rx_can_msg(struct ems_usb *dev, struct ems_cpc_msg *msg)
+{
+ struct can_frame *cf;
+ struct sk_buff *skb;
+ int i;
+ struct net_device_stats *stats = &dev->netdev->stats;
+
+ skb = netdev_alloc_skb(dev->netdev, sizeof(struct can_frame));
+ if (skb == NULL)
+ return;
+
+ skb->protocol = htons(ETH_P_CAN);
+
+ cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
+
+ cf->can_id = msg->msg.can_msg.id;
+ cf->can_dlc = min_t(u8, msg->msg.can_msg.length, 8);
+
+ if (msg->type == CPC_MSG_TYPE_EXT_CAN_FRAME
+ || msg->type == CPC_MSG_TYPE_EXT_RTR_FRAME)
+ cf->can_id |= CAN_EFF_FLAG;
+
+ if (msg->type == CPC_MSG_TYPE_RTR_FRAME
+ || msg->type == CPC_MSG_TYPE_EXT_RTR_FRAME) {
+ cf->can_id |= CAN_RTR_FLAG;
+ } else {
+ for (i = 0; i < cf->can_dlc; i++)
+ cf->data[i] = msg->msg.can_msg.msg[i];
+ }
+
+ netif_rx(skb);
+
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+}
+
+static void ems_usb_rx_err(struct ems_usb *dev, struct ems_cpc_msg *msg)
+{
+ struct can_frame *cf;
+ struct sk_buff *skb;
+ struct net_device_stats *stats = &dev->netdev->stats;
+
+ skb = netdev_alloc_skb(dev->netdev, sizeof(struct can_frame));
+ if (skb == NULL)
+ return;
+
+ skb->protocol = htons(ETH_P_CAN);
+
+ cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
+ memset(cf, 0, sizeof(struct can_frame));
+
+ cf->can_id = CAN_ERR_FLAG;
+ cf->can_dlc = CAN_ERR_DLC;
+
+ if (msg->type == CPC_MSG_TYPE_CAN_STATE) {
+ u8 state = msg->msg.can_state;
+
+ if (state & SJA1000_SR_BS) {
+ dev->can.state = CAN_STATE_BUS_OFF;
+ cf->can_id |= CAN_ERR_BUSOFF;
+
+ can_bus_off(dev->netdev);
+ } else if (state & SJA1000_SR_ES) {
+ dev->can.state = CAN_STATE_ERROR_WARNING;
+ dev->can.can_stats.error_warning++;
+ } else {
+ dev->can.state = CAN_STATE_ERROR_ACTIVE;
+ dev->can.can_stats.error_passive++;
+ }
+ } else if (msg->type == CPC_MSG_TYPE_CAN_FRAME_ERROR) {
+ u8 ecc = msg->msg.error.cc.regs.sja1000.ecc;
+ u8 txerr = msg->msg.error.cc.regs.sja1000.txerr;
+ u8 rxerr = msg->msg.error.cc.regs.sja1000.rxerr;
+
+ /* bus error interrupt */
+ dev->can.can_stats.bus_error++;
+ stats->rx_errors++;
+
+ cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
+
+ switch (ecc & SJA1000_ECC_MASK) {
+ case SJA1000_ECC_BIT:
+ cf->data[2] |= CAN_ERR_PROT_BIT;
+ break;
+ case SJA1000_ECC_FORM:
+ cf->data[2] |= CAN_ERR_PROT_FORM;
+ break;
+ case SJA1000_ECC_STUFF:
+ cf->data[2] |= CAN_ERR_PROT_STUFF;
+ break;
+ default:
+ cf->data[2] |= CAN_ERR_PROT_UNSPEC;
+ cf->data[3] = ecc & SJA1000_ECC_SEG;
+ break;
+ }
+
+ /* Error occured during transmission? */
+ if ((ecc & SJA1000_ECC_DIR) == 0)
+ cf->data[2] |= CAN_ERR_PROT_TX;
+
+ if (dev->can.state == CAN_STATE_ERROR_WARNING ||
+ dev->can.state == CAN_STATE_ERROR_PASSIVE) {
+ cf->data[1] = (txerr > rxerr) ?
+ CAN_ERR_CRTL_TX_PASSIVE : CAN_ERR_CRTL_RX_PASSIVE;
+ }
+ } else if (msg->type == CPC_MSG_TYPE_OVERRUN) {
+ cf->can_id |= CAN_ERR_CRTL;
+ cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
+
+ stats->rx_over_errors++;
+ stats->rx_errors++;
+ }
+
+ netif_rx(skb);
+
+ stats->rx_packets++;
+ stats->rx_bytes += cf->can_dlc;
+}
+
+/*
+ * callback for bulk IN urb
+ */
+static void ems_usb_read_bulk_callback(struct urb *urb)
+{
+ struct ems_usb *dev = urb->context;
+ struct net_device *netdev;
+ int retval;
+
+ netdev = dev->netdev;
+
+ if (!netif_device_present(netdev))
+ return;
+
+ switch (urb->status) {
+ case 0: /* success */
+ break;
+
+ case -ENOENT:
+ return;
+
+ default:
+ dev_info(netdev->dev.parent, "Rx URB aborted (%d)\n",
+ urb->status);
+ goto resubmit_urb;
+ }
+
+ if (urb->actual_length > CPC_HEADER_SIZE) {
+ struct ems_cpc_msg *msg;
+ u8 *ibuf = urb->transfer_buffer;
+ u8 msg_count, again, start;
+
+ msg_count = ibuf[0] & ~0x80;
+ again = ibuf[0] & 0x80;
+
+ start = CPC_HEADER_SIZE;
+
+ while (msg_count) {
+ msg = (struct ems_cpc_msg *)&ibuf[start];
+
+ switch (msg->type) {
+ case CPC_MSG_TYPE_CAN_STATE:
+ /* Process CAN state changes */
+ ems_usb_rx_err(dev, msg);
+ break;
+
+ case CPC_MSG_TYPE_CAN_FRAME:
+ case CPC_MSG_TYPE_EXT_CAN_FRAME:
+ case CPC_MSG_TYPE_RTR_FRAME:
+ case CPC_MSG_TYPE_EXT_RTR_FRAME:
+ ems_usb_rx_can_msg(dev, msg);
+ break;
+
+ case CPC_MSG_TYPE_CAN_FRAME_ERROR:
+ /* Process errorframe */
+ ems_usb_rx_err(dev, msg);
+ break;
+
+ case CPC_MSG_TYPE_OVERRUN:
+ /* Message lost while receiving */
+ ems_usb_rx_err(dev, msg);
+ break;
+ }
+
+ start += CPC_MSG_HEADER_LEN + msg->length;
+ msg_count--;
+
+ if (start > urb->transfer_buffer_length) {
+ dev_err(netdev->dev.parent, "format error\n");
+ break;
+ }
+ }
+ }
+
+resubmit_urb:
+ usb_fill_bulk_urb(urb, dev->udev, usb_rcvbulkpipe(dev->udev, 2),
+ urb->transfer_buffer, RX_BUFFER_SIZE,
+ ems_usb_read_bulk_callback, dev);
+
+ retval = usb_submit_urb(urb, GFP_ATOMIC);
+
+ if (retval == -ENODEV)
+ netif_device_detach(netdev);
+ else if (retval)
+ dev_err(netdev->dev.parent,
+ "failed resubmitting read bulk urb: %d\n", retval);
+
+ return;
+}
+
+/*
+ * callback for bulk IN urb
+ */
+static void ems_usb_write_bulk_callback(struct urb *urb)
+{
+ struct ems_tx_urb_context *context = urb->context;
+ struct ems_usb *dev;
+ struct net_device *netdev;
+
+ BUG_ON(!context);
+
+ dev = context->dev;
+ netdev = dev->netdev;
+
+ /* free up our allocated buffer */
+ usb_buffer_free(urb->dev, urb->transfer_buffer_length,
+ urb->transfer_buffer, urb->transfer_dma);
+
+ atomic_dec(&dev->active_tx_urbs);
+
+ if (!netif_device_present(netdev))
+ return;
+
+ if (urb->status)
+ dev_info(netdev->dev.parent, "Tx URB aborted (%d)\n",
+ urb->status);
+
+ netdev->trans_start = jiffies;
+
+ /* transmission complete interrupt */
+ netdev->stats.tx_packets++;
+ netdev->stats.tx_bytes += context->dlc;
+
+ can_get_echo_skb(netdev, context->echo_index);
+
+ /* Release context */
+ context->echo_index = MAX_TX_URBS;
+
+ if (netif_queue_stopped(netdev))
+ netif_wake_queue(netdev);
+}
+
+/*
+ * Send the given CPC command synchronously
+ */
+static int ems_usb_command_msg(struct ems_usb *dev, struct ems_cpc_msg *msg)
+{
+ int actual_length;
+
+ /* Copy payload */
+ memcpy(&dev->tx_msg_buffer[CPC_HEADER_SIZE], msg,
+ msg->length + CPC_MSG_HEADER_LEN);
+
+ /* Clear header */
+ memset(&dev->tx_msg_buffer[0], 0, CPC_HEADER_SIZE);
+
+ return usb_bulk_msg(dev->udev, usb_sndbulkpipe(dev->udev, 2),
+ &dev->tx_msg_buffer[0],
+ msg->length + CPC_MSG_HEADER_LEN + CPC_HEADER_SIZE,
+ &actual_length, 1000);
+}
+
+/*
+ * Change CAN controllers' mode register
+ */
+static int ems_usb_write_mode(struct ems_usb *dev, u8 mode)
+{
+ dev->active_params.msg.can_params.cc_params.sja1000.mode = mode;
+
+ return ems_usb_command_msg(dev, &dev->active_params);
+}
+
+/*
+ * Send a CPC_Control command to change behaviour when interface receives a CAN
+ * message, bus error or CAN state changed notifications.
+ */
+static int ems_usb_control_cmd(struct ems_usb *dev, u8 val)
+{
+ struct ems_cpc_msg cmd;
+
+ cmd.type = CPC_CMD_TYPE_CONTROL;
+ cmd.length = CPC_MSG_HEADER_LEN + 1;
+
+ cmd.msgid = 0;
+
+ cmd.msg.generic[0] = val;
+
+ return ems_usb_command_msg(dev, &cmd);
+}
+
+/*
+ * Start interface
+ */
+static int ems_usb_start(struct ems_usb *dev)
+{
+ struct net_device *netdev = dev->netdev;
+ int err, i;
+
+ dev->intr_in_buffer[0] = 0;
+ dev->free_slots = 15; /* initial size */
+
+ for (i = 0; i < MAX_RX_URBS; i++) {
+ struct urb *urb = NULL;
+ u8 *buf = NULL;
+
+ /* create a URB, and a buffer for it */
+ urb = usb_alloc_urb(0, GFP_KERNEL);
+ if (!urb) {
+ dev_err(netdev->dev.parent,
+ "No memory left for URBs\n");
+ return -ENOMEM;
+ }
+
+ buf = usb_buffer_alloc(dev->udev, RX_BUFFER_SIZE, GFP_KERNEL,
+ &urb->transfer_dma);
+ if (!buf) {
+ dev_err(netdev->dev.parent,
+ "No memory left for USB buffer\n");
+ usb_free_urb(urb);
+ return -ENOMEM;
+ }
+
+ usb_fill_bulk_urb(urb, dev->udev, usb_rcvbulkpipe(dev->udev, 2),
+ buf, RX_BUFFER_SIZE,
+ ems_usb_read_bulk_callback, dev);
+ urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+ usb_anchor_urb(urb, &dev->rx_submitted);
+
+ err = usb_submit_urb(urb, GFP_KERNEL);
+ if (err) {
+ if (err == -ENODEV)
+ netif_device_detach(dev->netdev);
+
+ usb_unanchor_urb(urb);
+ usb_buffer_free(dev->udev, RX_BUFFER_SIZE, buf,
+ urb->transfer_dma);
+ break;
+ }
+
+ /* Drop reference, USB core will take care of freeing it */
+ usb_free_urb(urb);
+ }
+
+ /* Did we submit any URBs */
+ if (i == 0) {
+ dev_warn(netdev->dev.parent, "couldn't setup read URBs\n");
+ return err;
+ }
+
+ /* Warn if we've couldn't transmit all the URBs */
+ if (i < MAX_RX_URBS)
+ dev_warn(netdev->dev.parent, "rx performance may be slow\n");
+
+ /* Setup and start interrupt URB */
+ usb_fill_int_urb(dev->intr_urb, dev->udev,
+ usb_rcvintpipe(dev->udev, 1),
+ dev->intr_in_buffer,
+ INTR_IN_BUFFER_SIZE,
+ ems_usb_read_interrupt_callback, dev, 1);
+
+ err = usb_submit_urb(dev->intr_urb, GFP_KERNEL);
+ if (err) {
+ if (err == -ENODEV)
+ netif_device_detach(dev->netdev);
+
+ dev_warn(netdev->dev.parent, "intr URB submit failed: %d\n",
+ err);
+
+ return err;
+ }
+
+ /* CPC-USB will transfer received message to host */
+ err = ems_usb_control_cmd(dev, CONTR_CAN_MESSAGE | CONTR_CONT_ON);
+ if (err)
+ goto failed;
+
+ /* CPC-USB will transfer CAN state changes to host */
+ err = ems_usb_control_cmd(dev, CONTR_CAN_STATE | CONTR_CONT_ON);
+ if (err)
+ goto failed;
+
+ /* CPC-USB will transfer bus errors to host */
+ err = ems_usb_control_cmd(dev, CONTR_BUS_ERROR | CONTR_CONT_ON);
+ if (err)
+ goto failed;
+
+ err = ems_usb_write_mode(dev, SJA1000_MOD_NORMAL);
+ if (err)
+ goto failed;
+
+ dev->can.state = CAN_STATE_ERROR_ACTIVE;
+
+ return 0;
+
+failed:
+ if (err == -ENODEV)
+ netif_device_detach(dev->netdev);
+
+ dev_warn(netdev->dev.parent, "couldn't submit control: %d\n", err);
+
+ return err;
+}
+
+static void unlink_all_urbs(struct ems_usb *dev)
+{
+ int i;
+
+ usb_unlink_urb(dev->intr_urb);
+
+ usb_kill_anchored_urbs(&dev->rx_submitted);
+
+ usb_kill_anchored_urbs(&dev->tx_submitted);
+ atomic_set(&dev->active_tx_urbs, 0);
+
+ for (i = 0; i < MAX_TX_URBS; i++)
+ dev->tx_contexts[i].echo_index = MAX_TX_URBS;
+}
+
+static int ems_usb_open(struct net_device *netdev)
+{
+ struct ems_usb *dev = netdev_priv(netdev);
+ int err;
+
+ err = ems_usb_write_mode(dev, SJA1000_MOD_RM);
+ if (err)
+ return err;
+
+ /* common open */
+ err = open_candev(netdev);
+ if (err)
+ return err;
+
+ /* finally start device */
+ err = ems_usb_start(dev);
+ if (err) {
+ if (err == -ENODEV)
+ netif_device_detach(dev->netdev);
+
+ dev_warn(netdev->dev.parent, "couldn't start device: %d\n",
+ err);
+
+ close_candev(netdev);
+
+ return err;
+ }
+
+ dev->open_time = jiffies;
+
+ netif_start_queue(netdev);
+
+ return 0;
+}
+
+static netdev_tx_t ems_usb_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+ struct ems_usb *dev = netdev_priv(netdev);
+ struct ems_tx_urb_context *context = NULL;
+ struct net_device_stats *stats = &netdev->stats;
+ struct can_frame *cf = (struct can_frame *)skb->data;
+ struct ems_cpc_msg *msg;
+ struct urb *urb;
+ u8 *buf;
+ int i, err;
+ size_t size = CPC_HEADER_SIZE + CPC_MSG_HEADER_LEN
+ + sizeof(struct cpc_can_msg);
+
+ /* create a URB, and a buffer for it, and copy the data to the URB */
+ urb = usb_alloc_urb(0, GFP_ATOMIC);
+ if (!urb) {
+ dev_err(netdev->dev.parent, "No memory left for URBs\n");
+ goto nomem;
+ }
+
+ buf = usb_buffer_alloc(dev->udev, size, GFP_ATOMIC, &urb->transfer_dma);
+ if (!buf) {
+ dev_err(netdev->dev.parent, "No memory left for USB buffer\n");
+ usb_free_urb(urb);
+ goto nomem;
+ }
+
+ msg = (struct ems_cpc_msg *)&buf[CPC_HEADER_SIZE];
+
+ msg->msg.can_msg.id = cf->can_id & CAN_ERR_MASK;
+ msg->msg.can_msg.length = cf->can_dlc;
+
+ if (cf->can_id & CAN_RTR_FLAG) {
+ msg->type = cf->can_id & CAN_EFF_FLAG ?
+ CPC_CMD_TYPE_EXT_RTR_FRAME : CPC_CMD_TYPE_RTR_FRAME;
+
+ msg->length = CPC_CAN_MSG_MIN_SIZE;
+ } else {
+ msg->type = cf->can_id & CAN_EFF_FLAG ?
+ CPC_CMD_TYPE_EXT_CAN_FRAME : CPC_CMD_TYPE_CAN_FRAME;
+
+ for (i = 0; i < cf->can_dlc; i++)
+ msg->msg.can_msg.msg[i] = cf->data[i];
+
+ msg->length = CPC_CAN_MSG_MIN_SIZE + cf->can_dlc;
+ }
+
+ for (i = 0; i < MAX_TX_URBS; i++) {
+ if (dev->tx_contexts[i].echo_index == MAX_TX_URBS) {
+ context = &dev->tx_contexts[i];
+ break;
+ }
+ }
+
+ /*
+ * May never happen! When this happens we'd more URBs in flight as
+ * allowed (MAX_TX_URBS).
+ */
+ if (!context) {
+ usb_unanchor_urb(urb);
+ usb_buffer_free(dev->udev, size, buf, urb->transfer_dma);
+
+ dev_warn(netdev->dev.parent, "couldn't find free context\n");
+
+ return NETDEV_TX_BUSY;
+ }
+
+ context->dev = dev;
+ context->echo_index = i;
+ context->dlc = cf->can_dlc;
+
+ usb_fill_bulk_urb(urb, dev->udev, usb_sndbulkpipe(dev->udev, 2), buf,
+ size, ems_usb_write_bulk_callback, context);
+ urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+ usb_anchor_urb(urb, &dev->tx_submitted);
+
+ can_put_echo_skb(skb, netdev, context->echo_index);
+
+ atomic_inc(&dev->active_tx_urbs);
+
+ err = usb_submit_urb(urb, GFP_ATOMIC);
+ if (unlikely(err)) {
+ can_free_echo_skb(netdev, context->echo_index);
+
+ usb_unanchor_urb(urb);
+ usb_buffer_free(dev->udev, size, buf, urb->transfer_dma);
+ dev_kfree_skb(skb);
+
+ atomic_dec(&dev->active_tx_urbs);
+
+ if (err == -ENODEV) {
+ netif_device_detach(netdev);
+ } else {
+ dev_warn(netdev->dev.parent, "failed tx_urb %d\n", err);
+
+ stats->tx_dropped++;
+ }
+ } else {
+ netdev->trans_start = jiffies;
+
+ /* Slow down tx path */
+ if (atomic_read(&dev->active_tx_urbs) >= MAX_TX_URBS ||
+ dev->free_slots < 5) {
+ netif_stop_queue(netdev);
+ }
+ }
+
+ /*
+ * Release our reference to this URB, the USB core will eventually free
+ * it entirely.
+ */
+ usb_free_urb(urb);
+
+ return NETDEV_TX_OK;
+
+nomem:
+ if (skb)
+ dev_kfree_skb(skb);
+
+ stats->tx_dropped++;
+
+ return NETDEV_TX_OK;
+}
+
+static int ems_usb_close(struct net_device *netdev)
+{
+ struct ems_usb *dev = netdev_priv(netdev);
+
+ /* Stop polling */
+ unlink_all_urbs(dev);
+
+ netif_stop_queue(netdev);
+
+ /* Set CAN controller to reset mode */
+ if (ems_usb_write_mode(dev, SJA1000_MOD_RM))
+ dev_warn(netdev->dev.parent, "couldn't stop device");
+
+ close_candev(netdev);
+
+ dev->open_time = 0;
+
+ return 0;
+}
+
+static const struct net_device_ops ems_usb_netdev_ops = {
+ .ndo_open = ems_usb_open,
+ .ndo_stop = ems_usb_close,
+ .ndo_start_xmit = ems_usb_start_xmit,
+};
+
+static struct can_bittiming_const ems_usb_bittiming_const = {
+ .name = "ems_usb",
+ .tseg1_min = 1,
+ .tseg1_max = 16,
+ .tseg2_min = 1,
+ .tseg2_max = 8,
+ .sjw_max = 4,
+ .brp_min = 1,
+ .brp_max = 64,
+ .brp_inc = 1,
+};
+
+static int ems_usb_set_mode(struct net_device *netdev, enum can_mode mode)
+{
+ struct ems_usb *dev = netdev_priv(netdev);
+
+ if (!dev->open_time)
+ return -EINVAL;
+
+ switch (mode) {
+ case CAN_MODE_START:
+ if (ems_usb_write_mode(dev, SJA1000_MOD_NORMAL))
+ dev_warn(netdev->dev.parent, "couldn't start device");
+
+ if (netif_queue_stopped(netdev))
+ netif_wake_queue(netdev);
+ break;
+
+ default:
+ return -EOPNOTSUPP;
+ }
+
+ return 0;
+}
+
+static int ems_usb_set_bittiming(struct net_device *netdev)
+{
+ struct ems_usb *dev = netdev_priv(netdev);
+ struct can_bittiming *bt = &dev->can.bittiming;
+ u8 btr0, btr1;
+
+ btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6);
+ btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) |
+ (((bt->phase_seg2 - 1) & 0x7) << 4);
+ if (dev->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
+ btr1 |= 0x80;
+
+ dev_info(netdev->dev.parent, "setting BTR0=0x%02x BTR1=0x%02x\n",
+ btr0, btr1);
+
+ dev->active_params.msg.can_params.cc_params.sja1000.btr0 = btr0;
+ dev->active_params.msg.can_params.cc_params.sja1000.btr1 = btr1;
+
+ return ems_usb_command_msg(dev, &dev->active_params);
+}
+
+static void init_params_sja1000(struct ems_cpc_msg *msg)
+{
+ struct cpc_sja1000_params *sja1000 =
+ &msg->msg.can_params.cc_params.sja1000;
+
+ msg->type = CPC_CMD_TYPE_CAN_PARAMS;
+ msg->length = sizeof(struct cpc_can_params);
+ msg->msgid = 0;
+
+ msg->msg.can_params.cc_type = CPC_CC_TYPE_SJA1000;
+
+ /* Acceptance filter open */
+ sja1000->acc_code0 = 0x00;
+ sja1000->acc_code1 = 0x00;
+ sja1000->acc_code2 = 0x00;
+ sja1000->acc_code3 = 0x00;
+
+ /* Acceptance filter open */
+ sja1000->acc_mask0 = 0xFF;
+ sja1000->acc_mask1 = 0xFF;
+ sja1000->acc_mask2 = 0xFF;
+ sja1000->acc_mask3 = 0xFF;
+
+ sja1000->btr0 = 0;
+ sja1000->btr1 = 0;
+
+ sja1000->outp_contr = SJA1000_DEFAULT_OUTPUT_CONTROL;
+ sja1000->mode = SJA1000_MOD_RM;
+}
+
+/*
+ * probe function for new CPC-USB devices
+ */
+static int ems_usb_probe(struct usb_interface *intf,
+ const struct usb_device_id *id)
+{
+ struct net_device *netdev;
+ struct ems_usb *dev;
+ int i, err = -ENOMEM;
+
+ netdev = alloc_candev(sizeof(struct ems_usb));
+ if (!netdev) {
+ dev_err(netdev->dev.parent, "Couldn't alloc candev\n");
+ return -ENOMEM;
+ }
+
+ dev = netdev_priv(netdev);
+
+ dev->udev = interface_to_usbdev(intf);
+ dev->netdev = netdev;
+
+ dev->can.state = CAN_STATE_STOPPED;
+ dev->can.clock.freq = EMS_USB_ARM7_CLOCK;
+ dev->can.bittiming_const = &ems_usb_bittiming_const;
+ dev->can.do_set_bittiming = ems_usb_set_bittiming;
+ dev->can.do_set_mode = ems_usb_set_mode;
+
+ netdev->flags |= IFF_ECHO; /* we support local echo */
+
+ netdev->netdev_ops = &ems_usb_netdev_ops;
+
+ netdev->flags |= IFF_ECHO; /* we support local echo */
+
+ init_usb_anchor(&dev->rx_submitted);
+
+ init_usb_anchor(&dev->tx_submitted);
+ atomic_set(&dev->active_tx_urbs, 0);
+
+ for (i = 0; i < MAX_TX_URBS; i++)
+ dev->tx_contexts[i].echo_index = MAX_TX_URBS;
+
+ dev->intr_urb = usb_alloc_urb(0, GFP_KERNEL);
+ if (!dev->intr_urb) {
+ dev_err(netdev->dev.parent, "Couldn't alloc intr URB\n");
+ goto cleanup_candev;
+ }
+
+ dev->intr_in_buffer = kzalloc(INTR_IN_BUFFER_SIZE, GFP_KERNEL);
+ if (!dev->intr_in_buffer) {
+ dev_err(netdev->dev.parent, "Couldn't alloc Intr buffer\n");
+ goto cleanup_intr_urb;
+ }
+
+ dev->tx_msg_buffer = kzalloc(CPC_HEADER_SIZE +
+ sizeof(struct ems_cpc_msg), GFP_KERNEL);
+ if (!dev->tx_msg_buffer) {
+ dev_err(netdev->dev.parent, "Couldn't alloc Tx buffer\n");
+ goto cleanup_intr_in_buffer;
+ }
+
+ usb_set_intfdata(intf, dev);
+
+ SET_NETDEV_DEV(netdev, &intf->dev);
+
+ init_params_sja1000(&dev->active_params);
+
+ err = ems_usb_command_msg(dev, &dev->active_params);
+ if (err) {
+ dev_err(netdev->dev.parent,
+ "couldn't initialize controller: %d\n", err);
+ goto cleanup_tx_msg_buffer;
+ }
+
+ err = register_candev(netdev);
+ if (err) {
+ dev_err(netdev->dev.parent,
+ "couldn't register CAN device: %d\n", err);
+ goto cleanup_tx_msg_buffer;
+ }
+
+ return 0;
+
+cleanup_tx_msg_buffer:
+ kfree(dev->tx_msg_buffer);
+
+cleanup_intr_in_buffer:
+ kfree(dev->intr_in_buffer);
+
+cleanup_intr_urb:
+ usb_free_urb(dev->intr_urb);
+
+cleanup_candev:
+ free_candev(netdev);
+
+ return err;
+}
+
+/*
+ * called by the usb core when the device is removed from the system
+ */
+static void ems_usb_disconnect(struct usb_interface *intf)
+{
+ struct ems_usb *dev = usb_get_intfdata(intf);
+
+ usb_set_intfdata(intf, NULL);
+
+ if (dev) {
+ unregister_netdev(dev->netdev);
+ free_candev(dev->netdev);
+
+ unlink_all_urbs(dev);
+
+ usb_free_urb(dev->intr_urb);
+
+ kfree(dev->intr_in_buffer);
+ }
+}
+
+/* usb specific object needed to register this driver with the usb subsystem */
+static struct usb_driver ems_usb_driver = {
+ .name = "ems_usb",
+ .probe = ems_usb_probe,
+ .disconnect = ems_usb_disconnect,
+ .id_table = ems_usb_table,
+};
+
+static int __init ems_usb_init(void)
+{
+ int err;
+
+ printk(KERN_INFO "CPC-USB kernel driver loaded\n");
+
+ /* register this driver with the USB subsystem */
+ err = usb_register(&ems_usb_driver);
+
+ if (err) {
+ err("usb_register failed. Error number %d\n", err);
+ return err;
+ }
+
+ return 0;
+}
+
+static void __exit ems_usb_exit(void)
+{
+ /* deregister this driver with the USB subsystem */
+ usb_deregister(&ems_usb_driver);
+}
+
+module_init(ems_usb_init);
+module_exit(ems_usb_exit);
cp->uio_dev = iminor(inode);
- cnic_shutdown_bnx2_rx_ring(dev);
-
cnic_init_bnx2_tx_ring(dev);
cnic_init_bnx2_rx_ring(dev);
struct cnic_dev *dev = uinfo->priv;
struct cnic_local *cp = dev->cnic_priv;
+ cnic_shutdown_bnx2_rx_ring(dev);
+
cp->uio_dev = -1;
return 0;
}
cnic_ulp_init(dev);
else if (event == NETDEV_UNREGISTER)
cnic_ulp_exit(dev);
- else if (event == NETDEV_UP) {
+
+ if (event == NETDEV_UP) {
if (cnic_register_netdev(dev) != 0) {
cnic_put(dev);
goto done;
#ifndef CNIC_IF_H
#define CNIC_IF_H
-#define CNIC_MODULE_VERSION "2.0.0"
-#define CNIC_MODULE_RELDATE "May 21, 2009"
+#define CNIC_MODULE_VERSION "2.0.1"
+#define CNIC_MODULE_RELDATE "Oct 01, 2009"
#define CNIC_ULP_RDMA 0
#define CNIC_ULP_ISCSI 1
static int __devinit cpmac_probe(struct platform_device *pdev)
{
int rc, phy_id;
- char mdio_bus_id[BUS_ID_SIZE];
+ char mdio_bus_id[MII_BUS_ID_SIZE];
struct resource *mem;
struct cpmac_priv *priv;
struct net_device *dev;
pdata = pdev->dev.platform_data;
if (external_switch || dumb_switch) {
- strncpy(mdio_bus_id, "0", BUS_ID_SIZE); /* fixed phys bus */
+ strncpy(mdio_bus_id, "0", MII_BUS_ID_SIZE); /* fixed phys bus */
phy_id = pdev->id;
} else {
for (phy_id = 0; phy_id < PHY_MAX_ADDR; phy_id++) {
continue;
if (!cpmac_mii->phy_map[phy_id])
continue;
- strncpy(mdio_bus_id, cpmac_mii->id, BUS_ID_SIZE);
+ strncpy(mdio_bus_id, cpmac_mii->id, MII_BUS_ID_SIZE);
break;
}
}
priv->msg_enable = netif_msg_init(debug_level, 0xff);
memcpy(dev->dev_addr, pdata->dev_addr, sizeof(dev->dev_addr));
- snprintf(priv->phy_name, BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
+ snprintf(priv->phy_name, MII_BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
priv->phy = phy_connect(dev, priv->phy_name, &cpmac_adjust_link, 0,
PHY_INTERFACE_MODE_MII);
e100_set_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE, data);
- /* Renegotiate with link partner */
+ data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
if (autoneg_normal) {
- data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
- data |= BMCR_ANENABLE | BMCR_ANRESTART;
+ /* Renegotiate with link partner */
+ data |= BMCR_ANENABLE | BMCR_ANRESTART;
+ } else {
+ /* Don't negotiate speed or duplex */
+ data &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
+
+ /* Set speed and duplex static */
+ if (current_speed_selection == 10)
+ data &= ~BMCR_SPEED100;
+ else
+ data |= BMCR_SPEED100;
+
+ if (current_duplex != full)
+ data &= ~BMCR_FULLDPLX;
+ else
+ data |= BMCR_FULLDPLX;
}
e100_set_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR, data);
}
/** NOTE:: For DM646x the IN_VECTOR has changed */
#define EMAC_DM646X_MAC_IN_VECTOR_RX_INT_VEC BIT(EMAC_DEF_RX_CH)
#define EMAC_DM646X_MAC_IN_VECTOR_TX_INT_VEC BIT(16 + EMAC_DEF_TX_CH)
+#define EMAC_DM646X_MAC_IN_VECTOR_HOST_INT BIT(26)
+#define EMAC_DM646X_MAC_IN_VECTOR_STATPEND_INT BIT(27)
+
/* CPPI bit positions */
#define EMAC_CPPI_SOP_BIT BIT(31)
emac_int_enable(priv);
}
- if (unlikely(status & EMAC_DM644X_MAC_IN_VECTOR_HOST_INT)) {
+ mask = EMAC_DM644X_MAC_IN_VECTOR_HOST_INT;
+ if (priv->version == EMAC_VERSION_2)
+ mask = EMAC_DM646X_MAC_IN_VECTOR_HOST_INT;
+
+ if (unlikely(status & mask)) {
u32 ch, cause;
dev_err(emac_dev, "DaVinci EMAC: Fatal Hardware Error\n");
netif_stop_queue(ndev);
#define AUTO_ALL_MODES 0
#define E1000_EEPROM_82544_APM 0x0004
-#define E1000_EEPROM_ICH8_APME 0x0004
#define E1000_EEPROM_APME 0x0400
#ifndef E1000_MASTER_SLAVE
u64 hw_csum_err;
u64 hw_csum_good;
- u64 rx_hdr_split;
u32 alloc_rx_buff_failed;
u32 rx_int_delay;
u32 rx_abs_int_delay;
struct e1000_rx_ring test_rx_ring;
int msg_enable;
- bool have_msi;
/* to not mess up cache alignment, always add to the bottom */
bool tso_force;
{ "rx_long_byte_count", E1000_STAT(stats.gorcl) },
{ "rx_csum_offload_good", E1000_STAT(hw_csum_good) },
{ "rx_csum_offload_errors", E1000_STAT(hw_csum_err) },
- { "rx_header_split", E1000_STAT(rx_hdr_split) },
{ "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) },
{ "tx_smbus", E1000_STAT(stats.mgptc) },
{ "rx_smbus", E1000_STAT(stats.mgprc) },
SUPPORTED_1000baseT_Full|
SUPPORTED_Autoneg |
SUPPORTED_TP);
- if (hw->phy_type == e1000_phy_ife)
- ecmd->supported &= ~SUPPORTED_1000baseT_Full;
ecmd->advertising = ADVERTISED_TP;
if (hw->autoneg == 1) {
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- /* When SoL/IDER sessions are active, autoneg/speed/duplex
- * cannot be changed */
- if (e1000_check_phy_reset_block(hw)) {
- DPRINTK(DRV, ERR, "Cannot change link characteristics "
- "when SoL/IDER is active.\n");
- return -EINVAL;
- }
-
while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
msleep(1);
else
netdev->features &= ~NETIF_F_TSO;
- if (data && (adapter->hw.mac_type > e1000_82547_rev_2))
- netdev->features |= NETIF_F_TSO6;
- else
- netdev->features &= ~NETIF_F_TSO6;
+ netdev->features &= ~NETIF_F_TSO6;
DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled");
adapter->tso_force = true;
regs_buff[24] = (u32)phy_data; /* phy local receiver status */
regs_buff[25] = regs_buff[24]; /* phy remote receiver status */
if (hw->mac_type >= e1000_82540 &&
- hw->mac_type < e1000_82571 &&
hw->media_type == e1000_media_type_copper) {
regs_buff[26] = er32(MANC);
}
ret_val = e1000_write_eeprom(hw, first_word,
last_word - first_word + 1, eeprom_buff);
- /* Update the checksum over the first part of the EEPROM if needed
- * and flush shadow RAM for 82573 conrollers */
- if ((ret_val == 0) && ((first_word <= EEPROM_CHECKSUM_REG) ||
- (hw->mac_type == e1000_82573)))
+ /* Update the checksum over the first part of the EEPROM if needed */
+ if ((ret_val == 0) && (first_word <= EEPROM_CHECKSUM_REG))
e1000_update_eeprom_checksum(hw);
kfree(eeprom_buff);
struct ethtool_drvinfo *drvinfo)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
- struct e1000_hw *hw = &adapter->hw;
char firmware_version[32];
- u16 eeprom_data;
strncpy(drvinfo->driver, e1000_driver_name, 32);
strncpy(drvinfo->version, e1000_driver_version, 32);
- /* EEPROM image version # is reported as firmware version # for
- * 8257{1|2|3} controllers */
- e1000_read_eeprom(hw, 5, 1, &eeprom_data);
- switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- case e1000_ich8lan:
- sprintf(firmware_version, "%d.%d-%d",
- (eeprom_data & 0xF000) >> 12,
- (eeprom_data & 0x0FF0) >> 4,
- eeprom_data & 0x000F);
- break;
- default:
- sprintf(firmware_version, "N/A");
- }
-
+ sprintf(firmware_version, "N/A");
strncpy(drvinfo->fw_version, firmware_version, 32);
strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32);
drvinfo->regdump_len = e1000_get_regs_len(netdev);
/* The status register is Read Only, so a write should fail.
* Some bits that get toggled are ignored.
*/
- switch (hw->mac_type) {
+
/* there are several bits on newer hardware that are r/w */
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
- toggle = 0x7FFFF3FF;
- break;
- case e1000_82573:
- case e1000_ich8lan:
- toggle = 0x7FFFF033;
- break;
- default:
- toggle = 0xFFFFF833;
- break;
- }
+ toggle = 0xFFFFF833;
before = er32(STATUS);
value = (er32(STATUS) & toggle);
/* restore previous status */
ew32(STATUS, before);
- if (hw->mac_type != e1000_ich8lan) {
- REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
- REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF);
- REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF);
- REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF);
- }
+ REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF);
+ REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF);
REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF);
REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF);
REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000);
- before = (hw->mac_type == e1000_ich8lan ?
- 0x06C3B33E : 0x06DFB3FE);
+ before = 0x06DFB3FE;
REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB);
REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000);
REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF);
REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
- if (hw->mac_type != e1000_ich8lan)
- REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
+ REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF);
- value = (hw->mac_type == e1000_ich8lan ?
- E1000_RAR_ENTRIES_ICH8LAN : E1000_RAR_ENTRIES);
+ value = E1000_RAR_ENTRIES;
for (i = 0; i < value; i++) {
REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF,
0xFFFFFFFF);
}
- value = (hw->mac_type == e1000_ich8lan ?
- E1000_MC_TBL_SIZE_ICH8LAN : E1000_MC_TBL_SIZE);
+ value = E1000_MC_TBL_SIZE;
for (i = 0; i < value; i++)
REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF);
/* Test each interrupt */
for (; i < 10; i++) {
- if (hw->mac_type == e1000_ich8lan && i == 8)
- continue;
-
/* Interrupt to test */
mask = 1 << i;
e1000_write_phy_reg(hw, PHY_CTRL, 0x9140);
/* autoneg off */
e1000_write_phy_reg(hw, PHY_CTRL, 0x8140);
- } else if (hw->phy_type == e1000_phy_gg82563)
- e1000_write_phy_reg(hw,
- GG82563_PHY_KMRN_MODE_CTRL,
- 0x1CC);
+ }
ctrl_reg = er32(CTRL);
- if (hw->phy_type == e1000_phy_ife) {
- /* force 100, set loopback */
- e1000_write_phy_reg(hw, PHY_CTRL, 0x6100);
+ /* force 1000, set loopback */
+ e1000_write_phy_reg(hw, PHY_CTRL, 0x4140);
- /* Now set up the MAC to the same speed/duplex as the PHY. */
- ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
- ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
- E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
- E1000_CTRL_SPD_100 |/* Force Speed to 100 */
- E1000_CTRL_FD); /* Force Duplex to FULL */
- } else {
- /* force 1000, set loopback */
- e1000_write_phy_reg(hw, PHY_CTRL, 0x4140);
-
- /* Now set up the MAC to the same speed/duplex as the PHY. */
- ctrl_reg = er32(CTRL);
- ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
- ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
- E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
- E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
- E1000_CTRL_FD); /* Force Duplex to FULL */
- }
+ /* Now set up the MAC to the same speed/duplex as the PHY. */
+ ctrl_reg = er32(CTRL);
+ ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
+ ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
+ E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
+ E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
if (hw->media_type == e1000_media_type_copper &&
hw->phy_type == e1000_phy_m88)
case e1000_82541_rev_2:
case e1000_82547:
case e1000_82547_rev_2:
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- case e1000_ich8lan:
return e1000_integrated_phy_loopback(adapter);
break;
-
default:
/* Default PHY loopback work is to read the MII
* control register and assert bit 14 (loopback mode).
case e1000_82546_rev_3:
return e1000_set_phy_loopback(adapter);
break;
- case e1000_82571:
- case e1000_82572:
-#define E1000_SERDES_LB_ON 0x410
- e1000_set_phy_loopback(adapter);
- ew32(SCTL, E1000_SERDES_LB_ON);
- msleep(10);
- return 0;
- break;
default:
rctl = er32(RCTL);
rctl |= E1000_RCTL_LBM_TCVR;
ew32(RCTL, rctl);
switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- if (hw->media_type == e1000_media_type_fiber ||
- hw->media_type == e1000_media_type_internal_serdes) {
-#define E1000_SERDES_LB_OFF 0x400
- ew32(SCTL, E1000_SERDES_LB_OFF);
- msleep(10);
- break;
- }
- /* Fall Through */
case e1000_82545:
case e1000_82546:
case e1000_82545_rev_3:
case e1000_82546_rev_3:
default:
hw->autoneg = true;
- if (hw->phy_type == e1000_phy_gg82563)
- e1000_write_phy_reg(hw,
- GG82563_PHY_KMRN_MODE_CTRL,
- 0x180);
e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg);
if (phy_reg & MII_CR_LOOPBACK) {
phy_reg &= ~MII_CR_LOOPBACK;
static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data)
{
- struct e1000_hw *hw = &adapter->hw;
-
- /* PHY loopback cannot be performed if SoL/IDER
- * sessions are active */
- if (e1000_check_phy_reset_block(hw)) {
- DPRINTK(DRV, ERR, "Cannot do PHY loopback test "
- "when SoL/IDER is active.\n");
- *data = 0;
- goto out;
- }
-
*data = e1000_setup_desc_rings(adapter);
if (*data)
goto out;
*data = 0;
if (hw->media_type == e1000_media_type_internal_serdes) {
int i = 0;
- hw->serdes_link_down = true;
+ hw->serdes_has_link = false;
/* On some blade server designs, link establishment
* could take as long as 2-3 minutes */
do {
e1000_check_for_link(hw);
- if (!hw->serdes_link_down)
+ if (hw->serdes_has_link)
return *data;
msleep(20);
} while (i++ < 3750);
case E1000_DEV_ID_82545EM_COPPER:
case E1000_DEV_ID_82546GB_QUAD_COPPER:
case E1000_DEV_ID_82546GB_PCIE:
- case E1000_DEV_ID_82571EB_SERDES_QUAD:
/* these don't support WoL at all */
wol->supported = 0;
break;
case E1000_DEV_ID_82546EB_FIBER:
case E1000_DEV_ID_82546GB_FIBER:
- case E1000_DEV_ID_82571EB_FIBER:
- case E1000_DEV_ID_82571EB_SERDES:
- case E1000_DEV_ID_82571EB_COPPER:
/* Wake events not supported on port B */
if (er32(STATUS) & E1000_STATUS_FUNC_1) {
wol->supported = 0;
/* return success for non excluded adapter ports */
retval = 0;
break;
- case E1000_DEV_ID_82571EB_QUAD_COPPER:
- case E1000_DEV_ID_82571EB_QUAD_FIBER:
- case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
- case E1000_DEV_ID_82571PT_QUAD_COPPER:
case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
/* quad port adapters only support WoL on port A */
if (!adapter->quad_port_a) {
if (!data)
data = INT_MAX;
- if (hw->mac_type < e1000_82571) {
- if (!adapter->blink_timer.function) {
- init_timer(&adapter->blink_timer);
- adapter->blink_timer.function = e1000_led_blink_callback;
- adapter->blink_timer.data = (unsigned long)adapter;
- }
- e1000_setup_led(hw);
- mod_timer(&adapter->blink_timer, jiffies);
- msleep_interruptible(data * 1000);
- del_timer_sync(&adapter->blink_timer);
- } else if (hw->phy_type == e1000_phy_ife) {
- if (!adapter->blink_timer.function) {
- init_timer(&adapter->blink_timer);
- adapter->blink_timer.function = e1000_led_blink_callback;
- adapter->blink_timer.data = (unsigned long)adapter;
- }
- mod_timer(&adapter->blink_timer, jiffies);
- msleep_interruptible(data * 1000);
- del_timer_sync(&adapter->blink_timer);
- e1000_write_phy_reg(&(adapter->hw), IFE_PHY_SPECIAL_CONTROL_LED, 0);
- } else {
- e1000_blink_led_start(hw);
- msleep_interruptible(data * 1000);
+ if (!adapter->blink_timer.function) {
+ init_timer(&adapter->blink_timer);
+ adapter->blink_timer.function = e1000_led_blink_callback;
+ adapter->blink_timer.data = (unsigned long)adapter;
}
+ e1000_setup_led(hw);
+ mod_timer(&adapter->blink_timer, jiffies);
+ msleep_interruptible(data * 1000);
+ del_timer_sync(&adapter->blink_timer);
e1000_led_off(hw);
clear_bit(E1000_LED_ON, &adapter->led_status);
e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
-*******************************************************************************/
+ */
/* e1000_hw.c
* Shared functions for accessing and configuring the MAC
*/
-
#include "e1000_hw.h"
-static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask);
-static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask);
-static s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 *data);
-static s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 data);
-static s32 e1000_get_software_semaphore(struct e1000_hw *hw);
-static void e1000_release_software_semaphore(struct e1000_hw *hw);
-
-static u8 e1000_arc_subsystem_valid(struct e1000_hw *hw);
static s32 e1000_check_downshift(struct e1000_hw *hw);
static s32 e1000_check_polarity(struct e1000_hw *hw,
e1000_rev_polarity *polarity);
static void e1000_clear_hw_cntrs(struct e1000_hw *hw);
static void e1000_clear_vfta(struct e1000_hw *hw);
-static s32 e1000_commit_shadow_ram(struct e1000_hw *hw);
static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw,
bool link_up);
static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw);
static s32 e1000_detect_gig_phy(struct e1000_hw *hw);
-static s32 e1000_erase_ich8_4k_segment(struct e1000_hw *hw, u32 bank);
static s32 e1000_get_auto_rd_done(struct e1000_hw *hw);
static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
u16 *max_length);
-static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw);
static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw);
-static s32 e1000_get_software_flag(struct e1000_hw *hw);
-static s32 e1000_ich8_cycle_init(struct e1000_hw *hw);
-static s32 e1000_ich8_flash_cycle(struct e1000_hw *hw, u32 timeout);
static s32 e1000_id_led_init(struct e1000_hw *hw);
-static s32 e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw,
- u32 cnf_base_addr,
- u32 cnf_size);
-static s32 e1000_init_lcd_from_nvm(struct e1000_hw *hw);
static void e1000_init_rx_addrs(struct e1000_hw *hw);
-static void e1000_initialize_hardware_bits(struct e1000_hw *hw);
-static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw);
-static s32 e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw);
-static s32 e1000_mng_enable_host_if(struct e1000_hw *hw);
-static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer, u16 length,
- u16 offset, u8 *sum);
-static s32 e1000_mng_write_cmd_header(struct e1000_hw* hw,
- struct e1000_host_mng_command_header
- *hdr);
-static s32 e1000_mng_write_commit(struct e1000_hw *hw);
-static s32 e1000_phy_ife_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info);
static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info);
-static s32 e1000_read_eeprom_eerd(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data);
-static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data);
-static s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd);
static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
struct e1000_phy_info *phy_info);
-static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
-static s32 e1000_read_ich8_byte(struct e1000_hw *hw, u32 index, u8 *data);
-static s32 e1000_verify_write_ich8_byte(struct e1000_hw *hw, u32 index,
- u8 byte);
-static s32 e1000_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 byte);
-static s32 e1000_read_ich8_word(struct e1000_hw *hw, u32 index, u16 *data);
-static s32 e1000_read_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 *data);
-static s32 e1000_write_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 data);
-static s32 e1000_read_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data);
-static s32 e1000_write_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data);
-static void e1000_release_software_flag(struct e1000_hw *hw);
static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active);
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
-static s32 e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, u32 no_snoop);
-static void e1000_set_pci_express_master_disable(struct e1000_hw *hw);
static s32 e1000_wait_autoneg(struct e1000_hw *hw);
static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value);
static s32 e1000_set_phy_type(struct e1000_hw *hw);
static s32 e1000_config_mac_to_phy(struct e1000_hw *hw);
static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl);
static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl);
-static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data,
- u16 count);
+static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count);
static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw);
static s32 e1000_phy_reset_dsp(struct e1000_hw *hw);
static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset,
- u16 words, u16 *data);
+ u16 words, u16 *data);
static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
u16 words, u16 *data);
static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw);
static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count);
static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
u16 phy_data);
-static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw,u32 reg_addr,
+static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
u16 *phy_data);
static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count);
static s32 e1000_acquire_eeprom(struct e1000_hw *hw);
static s32 e1000_set_vco_speed(struct e1000_hw *hw);
static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw);
static s32 e1000_set_phy_mode(struct e1000_hw *hw);
-static s32 e1000_host_if_read_cookie(struct e1000_hw *hw, u8 *buffer);
-static u8 e1000_calculate_mng_checksum(char *buffer, u32 length);
-static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex);
-static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw);
-static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
-static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data);
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data);
/* IGP cable length table */
static const
-u16 e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] =
- { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
- 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25,
- 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40,
- 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60,
- 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90,
- 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100,
- 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
- 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120};
-
-static const
-u16 e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] =
- { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21,
- 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41,
- 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61,
- 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82,
- 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104,
- 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121,
- 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124,
- 104, 109, 114, 118, 121, 124};
+u16 e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = {
+ 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+ 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25,
+ 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40,
+ 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60,
+ 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90,
+ 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100,
+ 100,
+ 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110,
+ 110, 110,
+ 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120,
+ 120, 120
+};
static DEFINE_SPINLOCK(e1000_eeprom_lock);
-/******************************************************************************
- * Set the phy type member in the hw struct.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
+/**
+ * e1000_set_phy_type - Set the phy type member in the hw struct.
+ * @hw: Struct containing variables accessed by shared code
+ */
static s32 e1000_set_phy_type(struct e1000_hw *hw)
{
- DEBUGFUNC("e1000_set_phy_type");
-
- if (hw->mac_type == e1000_undefined)
- return -E1000_ERR_PHY_TYPE;
-
- switch (hw->phy_id) {
- case M88E1000_E_PHY_ID:
- case M88E1000_I_PHY_ID:
- case M88E1011_I_PHY_ID:
- case M88E1111_I_PHY_ID:
- hw->phy_type = e1000_phy_m88;
- break;
- case IGP01E1000_I_PHY_ID:
- if (hw->mac_type == e1000_82541 ||
- hw->mac_type == e1000_82541_rev_2 ||
- hw->mac_type == e1000_82547 ||
- hw->mac_type == e1000_82547_rev_2) {
- hw->phy_type = e1000_phy_igp;
- break;
- }
- case IGP03E1000_E_PHY_ID:
- hw->phy_type = e1000_phy_igp_3;
- break;
- case IFE_E_PHY_ID:
- case IFE_PLUS_E_PHY_ID:
- case IFE_C_E_PHY_ID:
- hw->phy_type = e1000_phy_ife;
- break;
- case GG82563_E_PHY_ID:
- if (hw->mac_type == e1000_80003es2lan) {
- hw->phy_type = e1000_phy_gg82563;
- break;
- }
- /* Fall Through */
- default:
- /* Should never have loaded on this device */
- hw->phy_type = e1000_phy_undefined;
- return -E1000_ERR_PHY_TYPE;
- }
-
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * IGP phy init script - initializes the GbE PHY
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static void e1000_phy_init_script(struct e1000_hw *hw)
-{
- u32 ret_val;
- u16 phy_saved_data;
-
- DEBUGFUNC("e1000_phy_init_script");
-
- if (hw->phy_init_script) {
- msleep(20);
-
- /* Save off the current value of register 0x2F5B to be restored at
- * the end of this routine. */
- ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
-
- /* Disabled the PHY transmitter */
- e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
-
- msleep(20);
-
- e1000_write_phy_reg(hw,0x0000,0x0140);
-
- msleep(5);
-
- switch (hw->mac_type) {
- case e1000_82541:
- case e1000_82547:
- e1000_write_phy_reg(hw, 0x1F95, 0x0001);
-
- e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
-
- e1000_write_phy_reg(hw, 0x1F79, 0x0018);
-
- e1000_write_phy_reg(hw, 0x1F30, 0x1600);
-
- e1000_write_phy_reg(hw, 0x1F31, 0x0014);
-
- e1000_write_phy_reg(hw, 0x1F32, 0x161C);
-
- e1000_write_phy_reg(hw, 0x1F94, 0x0003);
-
- e1000_write_phy_reg(hw, 0x1F96, 0x003F);
-
- e1000_write_phy_reg(hw, 0x2010, 0x0008);
- break;
+ DEBUGFUNC("e1000_set_phy_type");
- case e1000_82541_rev_2:
- case e1000_82547_rev_2:
- e1000_write_phy_reg(hw, 0x1F73, 0x0099);
- break;
- default:
- break;
- }
+ if (hw->mac_type == e1000_undefined)
+ return -E1000_ERR_PHY_TYPE;
- e1000_write_phy_reg(hw, 0x0000, 0x3300);
-
- msleep(20);
-
- /* Now enable the transmitter */
- e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
-
- if (hw->mac_type == e1000_82547) {
- u16 fused, fine, coarse;
-
- /* Move to analog registers page */
- e1000_read_phy_reg(hw, IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused);
-
- if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
- e1000_read_phy_reg(hw, IGP01E1000_ANALOG_FUSE_STATUS, &fused);
+ switch (hw->phy_id) {
+ case M88E1000_E_PHY_ID:
+ case M88E1000_I_PHY_ID:
+ case M88E1011_I_PHY_ID:
+ case M88E1111_I_PHY_ID:
+ hw->phy_type = e1000_phy_m88;
+ break;
+ case IGP01E1000_I_PHY_ID:
+ if (hw->mac_type == e1000_82541 ||
+ hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ hw->phy_type = e1000_phy_igp;
+ break;
+ }
+ default:
+ /* Should never have loaded on this device */
+ hw->phy_type = e1000_phy_undefined;
+ return -E1000_ERR_PHY_TYPE;
+ }
- fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
- coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
+ return E1000_SUCCESS;
+}
- if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
- coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10;
- fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
- } else if (coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
- fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
+/**
+ * e1000_phy_init_script - IGP phy init script - initializes the GbE PHY
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_phy_init_script(struct e1000_hw *hw)
+{
+ u32 ret_val;
+ u16 phy_saved_data;
+
+ DEBUGFUNC("e1000_phy_init_script");
+
+ if (hw->phy_init_script) {
+ msleep(20);
+
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of this routine. */
+ ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ /* Disabled the PHY transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+ msleep(20);
+
+ e1000_write_phy_reg(hw, 0x0000, 0x0140);
+ msleep(5);
+
+ switch (hw->mac_type) {
+ case e1000_82541:
+ case e1000_82547:
+ e1000_write_phy_reg(hw, 0x1F95, 0x0001);
+ e1000_write_phy_reg(hw, 0x1F71, 0xBD21);
+ e1000_write_phy_reg(hw, 0x1F79, 0x0018);
+ e1000_write_phy_reg(hw, 0x1F30, 0x1600);
+ e1000_write_phy_reg(hw, 0x1F31, 0x0014);
+ e1000_write_phy_reg(hw, 0x1F32, 0x161C);
+ e1000_write_phy_reg(hw, 0x1F94, 0x0003);
+ e1000_write_phy_reg(hw, 0x1F96, 0x003F);
+ e1000_write_phy_reg(hw, 0x2010, 0x0008);
+ break;
- fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
- (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
- (coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK);
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ e1000_write_phy_reg(hw, 0x1F73, 0x0099);
+ break;
+ default:
+ break;
+ }
- e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_CONTROL, fused);
- e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_BYPASS,
- IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
- }
- }
- }
+ e1000_write_phy_reg(hw, 0x0000, 0x3300);
+ msleep(20);
+
+ /* Now enable the transmitter */
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (hw->mac_type == e1000_82547) {
+ u16 fused, fine, coarse;
+
+ /* Move to analog registers page */
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_SPARE_FUSE_STATUS,
+ &fused);
+
+ if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) {
+ e1000_read_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_STATUS,
+ &fused);
+
+ fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK;
+ coarse =
+ fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK;
+
+ if (coarse >
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH) {
+ coarse -=
+ IGP01E1000_ANALOG_FUSE_COARSE_10;
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_1;
+ } else if (coarse ==
+ IGP01E1000_ANALOG_FUSE_COARSE_THRESH)
+ fine -= IGP01E1000_ANALOG_FUSE_FINE_10;
+
+ fused =
+ (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) |
+ (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) |
+ (coarse &
+ IGP01E1000_ANALOG_FUSE_COARSE_MASK);
+
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_CONTROL,
+ fused);
+ e1000_write_phy_reg(hw,
+ IGP01E1000_ANALOG_FUSE_BYPASS,
+ IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL);
+ }
+ }
+ }
}
-/******************************************************************************
- * Set the mac type member in the hw struct.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
+/**
+ * e1000_set_mac_type - Set the mac type member in the hw struct.
+ * @hw: Struct containing variables accessed by shared code
+ */
s32 e1000_set_mac_type(struct e1000_hw *hw)
{
DEBUGFUNC("e1000_set_mac_type");
case E1000_DEV_ID_82547GI:
hw->mac_type = e1000_82547_rev_2;
break;
- case E1000_DEV_ID_82571EB_COPPER:
- case E1000_DEV_ID_82571EB_FIBER:
- case E1000_DEV_ID_82571EB_SERDES:
- case E1000_DEV_ID_82571EB_SERDES_DUAL:
- case E1000_DEV_ID_82571EB_SERDES_QUAD:
- case E1000_DEV_ID_82571EB_QUAD_COPPER:
- case E1000_DEV_ID_82571PT_QUAD_COPPER:
- case E1000_DEV_ID_82571EB_QUAD_FIBER:
- case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
- hw->mac_type = e1000_82571;
- break;
- case E1000_DEV_ID_82572EI_COPPER:
- case E1000_DEV_ID_82572EI_FIBER:
- case E1000_DEV_ID_82572EI_SERDES:
- case E1000_DEV_ID_82572EI:
- hw->mac_type = e1000_82572;
- break;
- case E1000_DEV_ID_82573E:
- case E1000_DEV_ID_82573E_IAMT:
- case E1000_DEV_ID_82573L:
- hw->mac_type = e1000_82573;
- break;
- case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
- case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
- case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
- case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
- hw->mac_type = e1000_80003es2lan;
- break;
- case E1000_DEV_ID_ICH8_IGP_M_AMT:
- case E1000_DEV_ID_ICH8_IGP_AMT:
- case E1000_DEV_ID_ICH8_IGP_C:
- case E1000_DEV_ID_ICH8_IFE:
- case E1000_DEV_ID_ICH8_IFE_GT:
- case E1000_DEV_ID_ICH8_IFE_G:
- case E1000_DEV_ID_ICH8_IGP_M:
- hw->mac_type = e1000_ich8lan;
- break;
default:
/* Should never have loaded on this device */
return -E1000_ERR_MAC_TYPE;
}
switch (hw->mac_type) {
- case e1000_ich8lan:
- hw->swfwhw_semaphore_present = true;
- hw->asf_firmware_present = true;
- break;
- case e1000_80003es2lan:
- hw->swfw_sync_present = true;
- /* fall through */
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- hw->eeprom_semaphore_present = true;
- /* fall through */
case e1000_82541:
case e1000_82547:
case e1000_82541_rev_2:
if (hw->mac_type == e1000_82543)
hw->bad_tx_carr_stats_fd = true;
- /* capable of receiving management packets to the host */
- if (hw->mac_type >= e1000_82571)
- hw->has_manc2h = true;
-
- /* In rare occasions, ESB2 systems would end up started without
- * the RX unit being turned on.
- */
- if (hw->mac_type == e1000_80003es2lan)
- hw->rx_needs_kicking = true;
-
if (hw->mac_type > e1000_82544)
hw->has_smbus = true;
return E1000_SUCCESS;
}
-/*****************************************************************************
- * Set media type and TBI compatibility.
- *
- * hw - Struct containing variables accessed by shared code
- * **************************************************************************/
+/**
+ * e1000_set_media_type - Set media type and TBI compatibility.
+ * @hw: Struct containing variables accessed by shared code
+ */
void e1000_set_media_type(struct e1000_hw *hw)
{
- u32 status;
-
- DEBUGFUNC("e1000_set_media_type");
-
- if (hw->mac_type != e1000_82543) {
- /* tbi_compatibility is only valid on 82543 */
- hw->tbi_compatibility_en = false;
- }
-
- switch (hw->device_id) {
- case E1000_DEV_ID_82545GM_SERDES:
- case E1000_DEV_ID_82546GB_SERDES:
- case E1000_DEV_ID_82571EB_SERDES:
- case E1000_DEV_ID_82571EB_SERDES_DUAL:
- case E1000_DEV_ID_82571EB_SERDES_QUAD:
- case E1000_DEV_ID_82572EI_SERDES:
- case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
- hw->media_type = e1000_media_type_internal_serdes;
- break;
- default:
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- hw->media_type = e1000_media_type_fiber;
- break;
- case e1000_ich8lan:
- case e1000_82573:
- /* The STATUS_TBIMODE bit is reserved or reused for the this
- * device.
- */
- hw->media_type = e1000_media_type_copper;
- break;
- default:
- status = er32(STATUS);
- if (status & E1000_STATUS_TBIMODE) {
- hw->media_type = e1000_media_type_fiber;
- /* tbi_compatibility not valid on fiber */
- hw->tbi_compatibility_en = false;
- } else {
- hw->media_type = e1000_media_type_copper;
- }
- break;
- }
- }
+ u32 status;
+
+ DEBUGFUNC("e1000_set_media_type");
+
+ if (hw->mac_type != e1000_82543) {
+ /* tbi_compatibility is only valid on 82543 */
+ hw->tbi_compatibility_en = false;
+ }
+
+ switch (hw->device_id) {
+ case E1000_DEV_ID_82545GM_SERDES:
+ case E1000_DEV_ID_82546GB_SERDES:
+ hw->media_type = e1000_media_type_internal_serdes;
+ break;
+ default:
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->media_type = e1000_media_type_fiber;
+ break;
+ default:
+ status = er32(STATUS);
+ if (status & E1000_STATUS_TBIMODE) {
+ hw->media_type = e1000_media_type_fiber;
+ /* tbi_compatibility not valid on fiber */
+ hw->tbi_compatibility_en = false;
+ } else {
+ hw->media_type = e1000_media_type_copper;
+ }
+ break;
+ }
+ }
}
-/******************************************************************************
- * Reset the transmit and receive units; mask and clear all interrupts.
+/**
+ * e1000_reset_hw: reset the hardware completely
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
+ * Reset the transmit and receive units; mask and clear all interrupts.
+ */
s32 e1000_reset_hw(struct e1000_hw *hw)
{
- u32 ctrl;
- u32 ctrl_ext;
- u32 icr;
- u32 manc;
- u32 led_ctrl;
- u32 timeout;
- u32 extcnf_ctrl;
- s32 ret_val;
-
- DEBUGFUNC("e1000_reset_hw");
-
- /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
- if (hw->mac_type == e1000_82542_rev2_0) {
- DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
- e1000_pci_clear_mwi(hw);
- }
-
- if (hw->bus_type == e1000_bus_type_pci_express) {
- /* Prevent the PCI-E bus from sticking if there is no TLP connection
- * on the last TLP read/write transaction when MAC is reset.
- */
- if (e1000_disable_pciex_master(hw) != E1000_SUCCESS) {
- DEBUGOUT("PCI-E Master disable polling has failed.\n");
- }
- }
-
- /* Clear interrupt mask to stop board from generating interrupts */
- DEBUGOUT("Masking off all interrupts\n");
- ew32(IMC, 0xffffffff);
-
- /* Disable the Transmit and Receive units. Then delay to allow
- * any pending transactions to complete before we hit the MAC with
- * the global reset.
- */
- ew32(RCTL, 0);
- ew32(TCTL, E1000_TCTL_PSP);
- E1000_WRITE_FLUSH();
-
- /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
- hw->tbi_compatibility_on = false;
-
- /* Delay to allow any outstanding PCI transactions to complete before
- * resetting the device
- */
- msleep(10);
-
- ctrl = er32(CTRL);
-
- /* Must reset the PHY before resetting the MAC */
- if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- ew32(CTRL, (ctrl | E1000_CTRL_PHY_RST));
- msleep(5);
- }
-
- /* Must acquire the MDIO ownership before MAC reset.
- * Ownership defaults to firmware after a reset. */
- if (hw->mac_type == e1000_82573) {
- timeout = 10;
-
- extcnf_ctrl = er32(EXTCNF_CTRL);
- extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
-
- do {
- ew32(EXTCNF_CTRL, extcnf_ctrl);
- extcnf_ctrl = er32(EXTCNF_CTRL);
-
- if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
- break;
- else
- extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
-
- msleep(2);
- timeout--;
- } while (timeout);
- }
-
- /* Workaround for ICH8 bit corruption issue in FIFO memory */
- if (hw->mac_type == e1000_ich8lan) {
- /* Set Tx and Rx buffer allocation to 8k apiece. */
- ew32(PBA, E1000_PBA_8K);
- /* Set Packet Buffer Size to 16k. */
- ew32(PBS, E1000_PBS_16K);
- }
-
- /* Issue a global reset to the MAC. This will reset the chip's
- * transmit, receive, DMA, and link units. It will not effect
- * the current PCI configuration. The global reset bit is self-
- * clearing, and should clear within a microsecond.
- */
- DEBUGOUT("Issuing a global reset to MAC\n");
-
- switch (hw->mac_type) {
- case e1000_82544:
- case e1000_82540:
- case e1000_82545:
- case e1000_82546:
- case e1000_82541:
- case e1000_82541_rev_2:
- /* These controllers can't ack the 64-bit write when issuing the
- * reset, so use IO-mapping as a workaround to issue the reset */
- E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
- break;
- case e1000_82545_rev_3:
- case e1000_82546_rev_3:
- /* Reset is performed on a shadow of the control register */
- ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST));
- break;
- case e1000_ich8lan:
- if (!hw->phy_reset_disable &&
- e1000_check_phy_reset_block(hw) == E1000_SUCCESS) {
- /* e1000_ich8lan PHY HW reset requires MAC CORE reset
- * at the same time to make sure the interface between
- * MAC and the external PHY is reset.
- */
- ctrl |= E1000_CTRL_PHY_RST;
- }
-
- e1000_get_software_flag(hw);
- ew32(CTRL, (ctrl | E1000_CTRL_RST));
- msleep(5);
- break;
- default:
- ew32(CTRL, (ctrl | E1000_CTRL_RST));
- break;
- }
-
- /* After MAC reset, force reload of EEPROM to restore power-on settings to
- * device. Later controllers reload the EEPROM automatically, so just wait
- * for reload to complete.
- */
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- /* Wait for reset to complete */
- udelay(10);
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- ew32(CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH();
- /* Wait for EEPROM reload */
- msleep(2);
- break;
- case e1000_82541:
- case e1000_82541_rev_2:
- case e1000_82547:
- case e1000_82547_rev_2:
- /* Wait for EEPROM reload */
- msleep(20);
- break;
- case e1000_82573:
- if (!e1000_is_onboard_nvm_eeprom(hw)) {
- udelay(10);
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- ew32(CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH();
- }
- /* fall through */
- default:
- /* Auto read done will delay 5ms or poll based on mac type */
- ret_val = e1000_get_auto_rd_done(hw);
- if (ret_val)
- return ret_val;
- break;
- }
-
- /* Disable HW ARPs on ASF enabled adapters */
- if (hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) {
- manc = er32(MANC);
- manc &= ~(E1000_MANC_ARP_EN);
- ew32(MANC, manc);
- }
-
- if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- e1000_phy_init_script(hw);
-
- /* Configure activity LED after PHY reset */
- led_ctrl = er32(LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- ew32(LEDCTL, led_ctrl);
- }
-
- /* Clear interrupt mask to stop board from generating interrupts */
- DEBUGOUT("Masking off all interrupts\n");
- ew32(IMC, 0xffffffff);
-
- /* Clear any pending interrupt events. */
- icr = er32(ICR);
-
- /* If MWI was previously enabled, reenable it. */
- if (hw->mac_type == e1000_82542_rev2_0) {
- if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
- e1000_pci_set_mwi(hw);
- }
-
- if (hw->mac_type == e1000_ich8lan) {
- u32 kab = er32(KABGTXD);
- kab |= E1000_KABGTXD_BGSQLBIAS;
- ew32(KABGTXD, kab);
- }
-
- return E1000_SUCCESS;
-}
+ u32 ctrl;
+ u32 ctrl_ext;
+ u32 icr;
+ u32 manc;
+ u32 led_ctrl;
+ s32 ret_val;
-/******************************************************************************
- *
- * Initialize a number of hardware-dependent bits
- *
- * hw: Struct containing variables accessed by shared code
- *
- * This function contains hardware limitation workarounds for PCI-E adapters
- *
- *****************************************************************************/
-static void e1000_initialize_hardware_bits(struct e1000_hw *hw)
-{
- if ((hw->mac_type >= e1000_82571) && (!hw->initialize_hw_bits_disable)) {
- /* Settings common to all PCI-express silicon */
- u32 reg_ctrl, reg_ctrl_ext;
- u32 reg_tarc0, reg_tarc1;
- u32 reg_tctl;
- u32 reg_txdctl, reg_txdctl1;
-
- /* link autonegotiation/sync workarounds */
- reg_tarc0 = er32(TARC0);
- reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27));
-
- /* Enable not-done TX descriptor counting */
- reg_txdctl = er32(TXDCTL);
- reg_txdctl |= E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL, reg_txdctl);
- reg_txdctl1 = er32(TXDCTL1);
- reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC;
- ew32(TXDCTL1, reg_txdctl1);
-
- switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- /* Clear PHY TX compatible mode bits */
- reg_tarc1 = er32(TARC1);
- reg_tarc1 &= ~((1 << 30)|(1 << 29));
-
- /* link autonegotiation/sync workarounds */
- reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23));
-
- /* TX ring control fixes */
- reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24));
-
- /* Multiple read bit is reversed polarity */
- reg_tctl = er32(TCTL);
- if (reg_tctl & E1000_TCTL_MULR)
- reg_tarc1 &= ~(1 << 28);
- else
- reg_tarc1 |= (1 << 28);
-
- ew32(TARC1, reg_tarc1);
- break;
- case e1000_82573:
- reg_ctrl_ext = er32(CTRL_EXT);
- reg_ctrl_ext &= ~(1 << 23);
- reg_ctrl_ext |= (1 << 22);
-
- /* TX byte count fix */
- reg_ctrl = er32(CTRL);
- reg_ctrl &= ~(1 << 29);
-
- ew32(CTRL_EXT, reg_ctrl_ext);
- ew32(CTRL, reg_ctrl);
- break;
- case e1000_80003es2lan:
- /* improve small packet performace for fiber/serdes */
- if ((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) {
- reg_tarc0 &= ~(1 << 20);
- }
-
- /* Multiple read bit is reversed polarity */
- reg_tctl = er32(TCTL);
- reg_tarc1 = er32(TARC1);
- if (reg_tctl & E1000_TCTL_MULR)
- reg_tarc1 &= ~(1 << 28);
- else
- reg_tarc1 |= (1 << 28);
-
- ew32(TARC1, reg_tarc1);
- break;
- case e1000_ich8lan:
- /* Reduce concurrent DMA requests to 3 from 4 */
- if ((hw->revision_id < 3) ||
- ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
- (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))
- reg_tarc0 |= ((1 << 29)|(1 << 28));
-
- reg_ctrl_ext = er32(CTRL_EXT);
- reg_ctrl_ext |= (1 << 22);
- ew32(CTRL_EXT, reg_ctrl_ext);
-
- /* workaround TX hang with TSO=on */
- reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23));
-
- /* Multiple read bit is reversed polarity */
- reg_tctl = er32(TCTL);
- reg_tarc1 = er32(TARC1);
- if (reg_tctl & E1000_TCTL_MULR)
- reg_tarc1 &= ~(1 << 28);
- else
- reg_tarc1 |= (1 << 28);
-
- /* workaround TX hang with TSO=on */
- reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24));
-
- ew32(TARC1, reg_tarc1);
- break;
- default:
- break;
- }
-
- ew32(TARC0, reg_tarc0);
- }
+ DEBUGFUNC("e1000_reset_hw");
+
+ /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ }
+
+ /* Clear interrupt mask to stop board from generating interrupts */
+ DEBUGOUT("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /* Disable the Transmit and Receive units. Then delay to allow
+ * any pending transactions to complete before we hit the MAC with
+ * the global reset.
+ */
+ ew32(RCTL, 0);
+ ew32(TCTL, E1000_TCTL_PSP);
+ E1000_WRITE_FLUSH();
+
+ /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
+ hw->tbi_compatibility_on = false;
+
+ /* Delay to allow any outstanding PCI transactions to complete before
+ * resetting the device
+ */
+ msleep(10);
+
+ ctrl = er32(CTRL);
+
+ /* Must reset the PHY before resetting the MAC */
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ ew32(CTRL, (ctrl | E1000_CTRL_PHY_RST));
+ msleep(5);
+ }
+
+ /* Issue a global reset to the MAC. This will reset the chip's
+ * transmit, receive, DMA, and link units. It will not effect
+ * the current PCI configuration. The global reset bit is self-
+ * clearing, and should clear within a microsecond.
+ */
+ DEBUGOUT("Issuing a global reset to MAC\n");
+
+ switch (hw->mac_type) {
+ case e1000_82544:
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82546:
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ /* These controllers can't ack the 64-bit write when issuing the
+ * reset, so use IO-mapping as a workaround to issue the reset */
+ E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
+ break;
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ /* Reset is performed on a shadow of the control register */
+ ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST));
+ break;
+ default:
+ ew32(CTRL, (ctrl | E1000_CTRL_RST));
+ break;
+ }
+
+ /* After MAC reset, force reload of EEPROM to restore power-on settings to
+ * device. Later controllers reload the EEPROM automatically, so just wait
+ * for reload to complete.
+ */
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* Wait for reset to complete */
+ udelay(10);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_EE_RST;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ /* Wait for EEPROM reload */
+ msleep(2);
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ /* Wait for EEPROM reload */
+ msleep(20);
+ break;
+ default:
+ /* Auto read done will delay 5ms or poll based on mac type */
+ ret_val = e1000_get_auto_rd_done(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ }
+
+ /* Disable HW ARPs on ASF enabled adapters */
+ if (hw->mac_type >= e1000_82540) {
+ manc = er32(MANC);
+ manc &= ~(E1000_MANC_ARP_EN);
+ ew32(MANC, manc);
+ }
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ e1000_phy_init_script(hw);
+
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ }
+
+ /* Clear interrupt mask to stop board from generating interrupts */
+ DEBUGOUT("Masking off all interrupts\n");
+ ew32(IMC, 0xffffffff);
+
+ /* Clear any pending interrupt events. */
+ icr = er32(ICR);
+
+ /* If MWI was previously enabled, reenable it. */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Performs basic configuration of the adapter.
- *
- * hw - Struct containing variables accessed by shared code
+/**
+ * e1000_init_hw: Performs basic configuration of the adapter.
+ * @hw: Struct containing variables accessed by shared code
*
* Assumes that the controller has previously been reset and is in a
* post-reset uninitialized state. Initializes the receive address registers,
* multicast table, and VLAN filter table. Calls routines to setup link
* configuration and flow control settings. Clears all on-chip counters. Leaves
* the transmit and receive units disabled and uninitialized.
- *****************************************************************************/
+ */
s32 e1000_init_hw(struct e1000_hw *hw)
{
- u32 ctrl;
- u32 i;
- s32 ret_val;
- u32 mta_size;
- u32 reg_data;
- u32 ctrl_ext;
-
- DEBUGFUNC("e1000_init_hw");
-
- /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */
- if ((hw->mac_type == e1000_ich8lan) &&
- ((hw->revision_id < 3) ||
- ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
- (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) {
- reg_data = er32(STATUS);
- reg_data &= ~0x80000000;
- ew32(STATUS, reg_data);
- }
-
- /* Initialize Identification LED */
- ret_val = e1000_id_led_init(hw);
- if (ret_val) {
- DEBUGOUT("Error Initializing Identification LED\n");
- return ret_val;
- }
-
- /* Set the media type and TBI compatibility */
- e1000_set_media_type(hw);
-
- /* Must be called after e1000_set_media_type because media_type is used */
- e1000_initialize_hardware_bits(hw);
-
- /* Disabling VLAN filtering. */
- DEBUGOUT("Initializing the IEEE VLAN\n");
- /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
- if (hw->mac_type != e1000_ich8lan) {
- if (hw->mac_type < e1000_82545_rev_3)
- ew32(VET, 0);
- e1000_clear_vfta(hw);
- }
-
- /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
- if (hw->mac_type == e1000_82542_rev2_0) {
- DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
- e1000_pci_clear_mwi(hw);
- ew32(RCTL, E1000_RCTL_RST);
- E1000_WRITE_FLUSH();
- msleep(5);
- }
-
- /* Setup the receive address. This involves initializing all of the Receive
- * Address Registers (RARs 0 - 15).
- */
- e1000_init_rx_addrs(hw);
-
- /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
- if (hw->mac_type == e1000_82542_rev2_0) {
- ew32(RCTL, 0);
- E1000_WRITE_FLUSH();
- msleep(1);
- if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
- e1000_pci_set_mwi(hw);
- }
-
- /* Zero out the Multicast HASH table */
- DEBUGOUT("Zeroing the MTA\n");
- mta_size = E1000_MC_TBL_SIZE;
- if (hw->mac_type == e1000_ich8lan)
- mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
- for (i = 0; i < mta_size; i++) {
- E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
- /* use write flush to prevent Memory Write Block (MWB) from
- * occuring when accessing our register space */
- E1000_WRITE_FLUSH();
- }
-
- /* Set the PCI priority bit correctly in the CTRL register. This
- * determines if the adapter gives priority to receives, or if it
- * gives equal priority to transmits and receives. Valid only on
- * 82542 and 82543 silicon.
- */
- if (hw->dma_fairness && hw->mac_type <= e1000_82543) {
- ctrl = er32(CTRL);
- ew32(CTRL, ctrl | E1000_CTRL_PRIOR);
- }
-
- switch (hw->mac_type) {
- case e1000_82545_rev_3:
- case e1000_82546_rev_3:
- break;
- default:
- /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
- if (hw->bus_type == e1000_bus_type_pcix && e1000_pcix_get_mmrbc(hw) > 2048)
- e1000_pcix_set_mmrbc(hw, 2048);
- break;
- }
-
- /* More time needed for PHY to initialize */
- if (hw->mac_type == e1000_ich8lan)
- msleep(15);
-
- /* Call a subroutine to configure the link and setup flow control. */
- ret_val = e1000_setup_link(hw);
-
- /* Set the transmit descriptor write-back policy */
- if (hw->mac_type > e1000_82544) {
- ctrl = er32(TXDCTL);
- ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
- ew32(TXDCTL, ctrl);
- }
-
- if (hw->mac_type == e1000_82573) {
- e1000_enable_tx_pkt_filtering(hw);
- }
-
- switch (hw->mac_type) {
- default:
- break;
- case e1000_80003es2lan:
- /* Enable retransmit on late collisions */
- reg_data = er32(TCTL);
- reg_data |= E1000_TCTL_RTLC;
- ew32(TCTL, reg_data);
-
- /* Configure Gigabit Carry Extend Padding */
- reg_data = er32(TCTL_EXT);
- reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
- reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX;
- ew32(TCTL_EXT, reg_data);
-
- /* Configure Transmit Inter-Packet Gap */
- reg_data = er32(TIPG);
- reg_data &= ~E1000_TIPG_IPGT_MASK;
- reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
- ew32(TIPG, reg_data);
-
- reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001);
- reg_data &= ~0x00100000;
- E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data);
- /* Fall through */
- case e1000_82571:
- case e1000_82572:
- case e1000_ich8lan:
- ctrl = er32(TXDCTL1);
- ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB;
- ew32(TXDCTL1, ctrl);
- break;
- }
-
-
- if (hw->mac_type == e1000_82573) {
- u32 gcr = er32(GCR);
- gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
- ew32(GCR, gcr);
- }
-
- /* Clear all of the statistics registers (clear on read). It is
- * important that we do this after we have tried to establish link
- * because the symbol error count will increment wildly if there
- * is no link.
- */
- e1000_clear_hw_cntrs(hw);
-
- /* ICH8 No-snoop bits are opposite polarity.
- * Set to snoop by default after reset. */
- if (hw->mac_type == e1000_ich8lan)
- e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL);
-
- if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
- hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
- ctrl_ext = er32(CTRL_EXT);
- /* Relaxed ordering must be disabled to avoid a parity
- * error crash in a PCI slot. */
- ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
- ew32(CTRL_EXT, ctrl_ext);
- }
-
- return ret_val;
-}
+ u32 ctrl;
+ u32 i;
+ s32 ret_val;
+ u32 mta_size;
+ u32 ctrl_ext;
-/******************************************************************************
- * Adjust SERDES output amplitude based on EEPROM setting.
- *
- * hw - Struct containing variables accessed by shared code.
- *****************************************************************************/
-static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw)
-{
- u16 eeprom_data;
- s32 ret_val;
-
- DEBUGFUNC("e1000_adjust_serdes_amplitude");
-
- if (hw->media_type != e1000_media_type_internal_serdes)
- return E1000_SUCCESS;
-
- switch (hw->mac_type) {
- case e1000_82545_rev_3:
- case e1000_82546_rev_3:
- break;
- default:
- return E1000_SUCCESS;
- }
-
- ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1, &eeprom_data);
- if (ret_val) {
- return ret_val;
- }
-
- if (eeprom_data != EEPROM_RESERVED_WORD) {
- /* Adjust SERDES output amplitude only. */
- eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data);
- if (ret_val)
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
+ DEBUGFUNC("e1000_init_hw");
-/******************************************************************************
- * Configures flow control and link settings.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Determines which flow control settings to use. Calls the apropriate media-
- * specific link configuration function. Configures the flow control settings.
- * Assuming the adapter has a valid link partner, a valid link should be
- * established. Assumes the hardware has previously been reset and the
- * transmitter and receiver are not enabled.
- *****************************************************************************/
-s32 e1000_setup_link(struct e1000_hw *hw)
-{
- u32 ctrl_ext;
- s32 ret_val;
- u16 eeprom_data;
-
- DEBUGFUNC("e1000_setup_link");
-
- /* In the case of the phy reset being blocked, we already have a link.
- * We do not have to set it up again. */
- if (e1000_check_phy_reset_block(hw))
- return E1000_SUCCESS;
-
- /* Read and store word 0x0F of the EEPROM. This word contains bits
- * that determine the hardware's default PAUSE (flow control) mode,
- * a bit that determines whether the HW defaults to enabling or
- * disabling auto-negotiation, and the direction of the
- * SW defined pins. If there is no SW over-ride of the flow
- * control setting, then the variable hw->fc will
- * be initialized based on a value in the EEPROM.
- */
- if (hw->fc == E1000_FC_DEFAULT) {
- switch (hw->mac_type) {
- case e1000_ich8lan:
- case e1000_82573:
- hw->fc = E1000_FC_FULL;
- break;
- default:
- ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
- 1, &eeprom_data);
- if (ret_val) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
- hw->fc = E1000_FC_NONE;
- else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
- EEPROM_WORD0F_ASM_DIR)
- hw->fc = E1000_FC_TX_PAUSE;
- else
- hw->fc = E1000_FC_FULL;
- break;
- }
- }
-
- /* We want to save off the original Flow Control configuration just
- * in case we get disconnected and then reconnected into a different
- * hub or switch with different Flow Control capabilities.
- */
- if (hw->mac_type == e1000_82542_rev2_0)
- hw->fc &= (~E1000_FC_TX_PAUSE);
-
- if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
- hw->fc &= (~E1000_FC_RX_PAUSE);
-
- hw->original_fc = hw->fc;
-
- DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
-
- /* Take the 4 bits from EEPROM word 0x0F that determine the initial
- * polarity value for the SW controlled pins, and setup the
- * Extended Device Control reg with that info.
- * This is needed because one of the SW controlled pins is used for
- * signal detection. So this should be done before e1000_setup_pcs_link()
- * or e1000_phy_setup() is called.
- */
- if (hw->mac_type == e1000_82543) {
- ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
- 1, &eeprom_data);
- if (ret_val) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
- SWDPIO__EXT_SHIFT);
- ew32(CTRL_EXT, ctrl_ext);
- }
-
- /* Call the necessary subroutine to configure the link. */
- ret_val = (hw->media_type == e1000_media_type_copper) ?
- e1000_setup_copper_link(hw) :
- e1000_setup_fiber_serdes_link(hw);
-
- /* Initialize the flow control address, type, and PAUSE timer
- * registers to their default values. This is done even if flow
- * control is disabled, because it does not hurt anything to
- * initialize these registers.
- */
- DEBUGOUT("Initializing the Flow Control address, type and timer regs\n");
-
- /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
- if (hw->mac_type != e1000_ich8lan) {
- ew32(FCT, FLOW_CONTROL_TYPE);
- ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
- ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
- }
-
- ew32(FCTTV, hw->fc_pause_time);
-
- /* Set the flow control receive threshold registers. Normally,
- * these registers will be set to a default threshold that may be
- * adjusted later by the driver's runtime code. However, if the
- * ability to transmit pause frames in not enabled, then these
- * registers will be set to 0.
- */
- if (!(hw->fc & E1000_FC_TX_PAUSE)) {
- ew32(FCRTL, 0);
- ew32(FCRTH, 0);
- } else {
- /* We need to set up the Receive Threshold high and low water marks
- * as well as (optionally) enabling the transmission of XON frames.
- */
- if (hw->fc_send_xon) {
- ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
- ew32(FCRTH, hw->fc_high_water);
- } else {
- ew32(FCRTL, hw->fc_low_water);
- ew32(FCRTH, hw->fc_high_water);
- }
- }
- return ret_val;
-}
+ /* Initialize Identification LED */
+ ret_val = e1000_id_led_init(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Initializing Identification LED\n");
+ return ret_val;
+ }
-/******************************************************************************
- * Sets up link for a fiber based or serdes based adapter
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Manipulates Physical Coding Sublayer functions in order to configure
- * link. Assumes the hardware has been previously reset and the transmitter
- * and receiver are not enabled.
- *****************************************************************************/
-static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
-{
- u32 ctrl;
- u32 status;
- u32 txcw = 0;
- u32 i;
- u32 signal = 0;
- s32 ret_val;
-
- DEBUGFUNC("e1000_setup_fiber_serdes_link");
-
- /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists
- * until explicitly turned off or a power cycle is performed. A read to
- * the register does not indicate its status. Therefore, we ensure
- * loopback mode is disabled during initialization.
- */
- if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572)
- ew32(SCTL, E1000_DISABLE_SERDES_LOOPBACK);
-
- /* On adapters with a MAC newer than 82544, SWDP 1 will be
- * set when the optics detect a signal. On older adapters, it will be
- * cleared when there is a signal. This applies to fiber media only.
- * If we're on serdes media, adjust the output amplitude to value
- * set in the EEPROM.
- */
- ctrl = er32(CTRL);
- if (hw->media_type == e1000_media_type_fiber)
- signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
-
- ret_val = e1000_adjust_serdes_amplitude(hw);
- if (ret_val)
- return ret_val;
-
- /* Take the link out of reset */
- ctrl &= ~(E1000_CTRL_LRST);
-
- /* Adjust VCO speed to improve BER performance */
- ret_val = e1000_set_vco_speed(hw);
- if (ret_val)
- return ret_val;
-
- e1000_config_collision_dist(hw);
-
- /* Check for a software override of the flow control settings, and setup
- * the device accordingly. If auto-negotiation is enabled, then software
- * will have to set the "PAUSE" bits to the correct value in the Tranmsit
- * Config Word Register (TXCW) and re-start auto-negotiation. However, if
- * auto-negotiation is disabled, then software will have to manually
- * configure the two flow control enable bits in the CTRL register.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames, but
- * not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but we do
- * not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
- */
- switch (hw->fc) {
- case E1000_FC_NONE:
- /* Flow control is completely disabled by a software over-ride. */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
- break;
- case E1000_FC_RX_PAUSE:
- /* RX Flow control is enabled and TX Flow control is disabled by a
- * software over-ride. Since there really isn't a way to advertise
- * that we are capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later, we will
- * disable the adapter's ability to send PAUSE frames.
- */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
- break;
- case E1000_FC_TX_PAUSE:
- /* TX Flow control is enabled, and RX Flow control is disabled, by a
- * software over-ride.
- */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
- break;
- case E1000_FC_FULL:
- /* Flow control (both RX and TX) is enabled by a software over-ride. */
- txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
- break;
- default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
- break;
- }
-
- /* Since auto-negotiation is enabled, take the link out of reset (the link
- * will be in reset, because we previously reset the chip). This will
- * restart auto-negotiation. If auto-neogtiation is successful then the
- * link-up status bit will be set and the flow control enable bits (RFCE
- * and TFCE) will be set according to their negotiated value.
- */
- DEBUGOUT("Auto-negotiation enabled\n");
-
- ew32(TXCW, txcw);
- ew32(CTRL, ctrl);
- E1000_WRITE_FLUSH();
-
- hw->txcw = txcw;
- msleep(1);
-
- /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
- * indication in the Device Status Register. Time-out if a link isn't
- * seen in 500 milliseconds seconds (Auto-negotiation should complete in
- * less than 500 milliseconds even if the other end is doing it in SW).
- * For internal serdes, we just assume a signal is present, then poll.
- */
- if (hw->media_type == e1000_media_type_internal_serdes ||
- (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) {
- DEBUGOUT("Looking for Link\n");
- for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
- msleep(10);
- status = er32(STATUS);
- if (status & E1000_STATUS_LU) break;
- }
- if (i == (LINK_UP_TIMEOUT / 10)) {
- DEBUGOUT("Never got a valid link from auto-neg!!!\n");
- hw->autoneg_failed = 1;
- /* AutoNeg failed to achieve a link, so we'll call
- * e1000_check_for_link. This routine will force the link up if
- * we detect a signal. This will allow us to communicate with
- * non-autonegotiating link partners.
- */
- ret_val = e1000_check_for_link(hw);
- if (ret_val) {
- DEBUGOUT("Error while checking for link\n");
- return ret_val;
- }
- hw->autoneg_failed = 0;
- } else {
- hw->autoneg_failed = 0;
- DEBUGOUT("Valid Link Found\n");
- }
- } else {
- DEBUGOUT("No Signal Detected\n");
- }
- return E1000_SUCCESS;
-}
+ /* Set the media type and TBI compatibility */
+ e1000_set_media_type(hw);
+
+ /* Disabling VLAN filtering. */
+ DEBUGOUT("Initializing the IEEE VLAN\n");
+ if (hw->mac_type < e1000_82545_rev_3)
+ ew32(VET, 0);
+ e1000_clear_vfta(hw);
+
+ /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
+ e1000_pci_clear_mwi(hw);
+ ew32(RCTL, E1000_RCTL_RST);
+ E1000_WRITE_FLUSH();
+ msleep(5);
+ }
-/******************************************************************************
-* Make sure we have a valid PHY and change PHY mode before link setup.
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_copper_link_preconfig(struct e1000_hw *hw)
-{
- u32 ctrl;
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_copper_link_preconfig");
-
- ctrl = er32(CTRL);
- /* With 82543, we need to force speed and duplex on the MAC equal to what
- * the PHY speed and duplex configuration is. In addition, we need to
- * perform a hardware reset on the PHY to take it out of reset.
- */
- if (hw->mac_type > e1000_82543) {
- ctrl |= E1000_CTRL_SLU;
- ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ew32(CTRL, ctrl);
- } else {
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
- ew32(CTRL, ctrl);
- ret_val = e1000_phy_hw_reset(hw);
- if (ret_val)
- return ret_val;
- }
-
- /* Make sure we have a valid PHY */
- ret_val = e1000_detect_gig_phy(hw);
- if (ret_val) {
- DEBUGOUT("Error, did not detect valid phy.\n");
- return ret_val;
- }
- DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
-
- /* Set PHY to class A mode (if necessary) */
- ret_val = e1000_set_phy_mode(hw);
- if (ret_val)
- return ret_val;
-
- if ((hw->mac_type == e1000_82545_rev_3) ||
- (hw->mac_type == e1000_82546_rev_3)) {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- phy_data |= 0x00000008;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- }
-
- if (hw->mac_type <= e1000_82543 ||
- hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
- hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2)
- hw->phy_reset_disable = false;
-
- return E1000_SUCCESS;
-}
+ /* Setup the receive address. This involves initializing all of the Receive
+ * Address Registers (RARs 0 - 15).
+ */
+ e1000_init_rx_addrs(hw);
+
+ /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
+ if (hw->mac_type == e1000_82542_rev2_0) {
+ ew32(RCTL, 0);
+ E1000_WRITE_FLUSH();
+ msleep(1);
+ if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
+ e1000_pci_set_mwi(hw);
+ }
+ /* Zero out the Multicast HASH table */
+ DEBUGOUT("Zeroing the MTA\n");
+ mta_size = E1000_MC_TBL_SIZE;
+ for (i = 0; i < mta_size; i++) {
+ E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
+ /* use write flush to prevent Memory Write Block (MWB) from
+ * occurring when accessing our register space */
+ E1000_WRITE_FLUSH();
+ }
-/********************************************************************
-* Copper link setup for e1000_phy_igp series.
-*
-* hw - Struct containing variables accessed by shared code
-*********************************************************************/
-static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw)
-{
- u32 led_ctrl;
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_copper_link_igp_setup");
-
- if (hw->phy_reset_disable)
- return E1000_SUCCESS;
-
- ret_val = e1000_phy_reset(hw);
- if (ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
-
- /* Wait 15ms for MAC to configure PHY from eeprom settings */
- msleep(15);
- if (hw->mac_type != e1000_ich8lan) {
- /* Configure activity LED after PHY reset */
- led_ctrl = er32(LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- ew32(LEDCTL, led_ctrl);
- }
-
- /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
- if (hw->phy_type == e1000_phy_igp) {
- /* disable lplu d3 during driver init */
- ret_val = e1000_set_d3_lplu_state(hw, false);
- if (ret_val) {
- DEBUGOUT("Error Disabling LPLU D3\n");
- return ret_val;
- }
- }
-
- /* disable lplu d0 during driver init */
- ret_val = e1000_set_d0_lplu_state(hw, false);
- if (ret_val) {
- DEBUGOUT("Error Disabling LPLU D0\n");
- return ret_val;
- }
- /* Configure mdi-mdix settings */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- hw->dsp_config_state = e1000_dsp_config_disabled;
- /* Force MDI for earlier revs of the IGP PHY */
- phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX | IGP01E1000_PSCR_FORCE_MDI_MDIX);
- hw->mdix = 1;
-
- } else {
- hw->dsp_config_state = e1000_dsp_config_enabled;
- phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
-
- switch (hw->mdix) {
- case 1:
- phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
- break;
- case 2:
- phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
- break;
- case 0:
- default:
- phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
- break;
- }
- }
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- /* set auto-master slave resolution settings */
- if (hw->autoneg) {
- e1000_ms_type phy_ms_setting = hw->master_slave;
-
- if (hw->ffe_config_state == e1000_ffe_config_active)
- hw->ffe_config_state = e1000_ffe_config_enabled;
-
- if (hw->dsp_config_state == e1000_dsp_config_activated)
- hw->dsp_config_state = e1000_dsp_config_enabled;
-
- /* when autonegotiation advertisment is only 1000Mbps then we
- * should disable SmartSpeed and enable Auto MasterSlave
- * resolution as hardware default. */
- if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
- /* Disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- /* Set auto Master/Slave resolution process */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
- phy_data &= ~CR_1000T_MS_ENABLE;
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- /* load defaults for future use */
- hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
- ((phy_data & CR_1000T_MS_VALUE) ?
- e1000_ms_force_master :
- e1000_ms_force_slave) :
- e1000_ms_auto;
-
- switch (phy_ms_setting) {
- case e1000_ms_force_master:
- phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
- break;
- case e1000_ms_force_slave:
- phy_data |= CR_1000T_MS_ENABLE;
- phy_data &= ~(CR_1000T_MS_VALUE);
- break;
- case e1000_ms_auto:
- phy_data &= ~CR_1000T_MS_ENABLE;
- default:
- break;
- }
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
+ /* Set the PCI priority bit correctly in the CTRL register. This
+ * determines if the adapter gives priority to receives, or if it
+ * gives equal priority to transmits and receives. Valid only on
+ * 82542 and 82543 silicon.
+ */
+ if (hw->dma_fairness && hw->mac_type <= e1000_82543) {
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PRIOR);
+ }
-/********************************************************************
-* Copper link setup for e1000_phy_gg82563 series.
-*
-* hw - Struct containing variables accessed by shared code
-*********************************************************************/
-static s32 e1000_copper_link_ggp_setup(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 phy_data;
- u32 reg_data;
-
- DEBUGFUNC("e1000_copper_link_ggp_setup");
-
- if (!hw->phy_reset_disable) {
-
- /* Enable CRS on TX for half-duplex operation. */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
- /* Use 25MHz for both link down and 1000BASE-T for Tx clock */
- phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ;
-
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
- phy_data);
- if (ret_val)
- return ret_val;
-
- /* Options:
- * MDI/MDI-X = 0 (default)
- * 0 - Auto for all speeds
- * 1 - MDI mode
- * 2 - MDI-X mode
- * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
- */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
-
- switch (hw->mdix) {
- case 1:
- phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
- break;
- case 2:
- phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
- break;
- case 0:
- default:
- phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
- break;
- }
-
- /* Options:
- * disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
- * 0 - Disabled
- * 1 - Enabled
- */
- phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
- if (hw->disable_polarity_correction == 1)
- phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data);
-
- if (ret_val)
- return ret_val;
-
- /* SW Reset the PHY so all changes take effect */
- ret_val = e1000_phy_reset(hw);
- if (ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
- } /* phy_reset_disable */
-
- if (hw->mac_type == e1000_80003es2lan) {
- /* Bypass RX and TX FIFO's */
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL,
- E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS |
- E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data);
-
- if (ret_val)
- return ret_val;
-
- reg_data = er32(CTRL_EXT);
- reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
- ew32(CTRL_EXT, reg_data);
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- /* Do not init these registers when the HW is in IAMT mode, since the
- * firmware will have already initialized them. We only initialize
- * them if the HW is not in IAMT mode.
- */
- if (!e1000_check_mng_mode(hw)) {
- /* Enable Electrical Idle on the PHY */
- phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL,
- phy_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL,
- phy_data);
-
- if (ret_val)
- return ret_val;
- }
-
- /* Workaround: Disable padding in Kumeran interface in the MAC
- * and in the PHY to avoid CRC errors.
- */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL,
- &phy_data);
- if (ret_val)
- return ret_val;
- phy_data |= GG82563_ICR_DIS_PADDING;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL,
- phy_data);
- if (ret_val)
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
+ if (hw->bus_type == e1000_bus_type_pcix
+ && e1000_pcix_get_mmrbc(hw) > 2048)
+ e1000_pcix_set_mmrbc(hw, 2048);
+ break;
+ }
-/********************************************************************
-* Copper link setup for e1000_phy_m88 series.
-*
-* hw - Struct containing variables accessed by shared code
-*********************************************************************/
-static s32 e1000_copper_link_mgp_setup(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_copper_link_mgp_setup");
-
- if (hw->phy_reset_disable)
- return E1000_SUCCESS;
-
- /* Enable CRS on TX. This must be set for half-duplex operation. */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
-
- /* Options:
- * MDI/MDI-X = 0 (default)
- * 0 - Auto for all speeds
- * 1 - MDI mode
- * 2 - MDI-X mode
- * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
-
- switch (hw->mdix) {
- case 1:
- phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
- break;
- case 2:
- phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
- break;
- case 3:
- phy_data |= M88E1000_PSCR_AUTO_X_1000T;
- break;
- case 0:
- default:
- phy_data |= M88E1000_PSCR_AUTO_X_MODE;
- break;
- }
-
- /* Options:
- * disable_polarity_correction = 0 (default)
- * Automatic Correction for Reversed Cable Polarity
- * 0 - Disabled
- * 1 - Enabled
- */
- phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
- if (hw->disable_polarity_correction == 1)
- phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- if (hw->phy_revision < M88E1011_I_REV_4) {
- /* Force TX_CLK in the Extended PHY Specific Control Register
- * to 25MHz clock.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
-
- if ((hw->phy_revision == E1000_REVISION_2) &&
- (hw->phy_id == M88E1111_I_PHY_ID)) {
- /* Vidalia Phy, set the downshift counter to 5x */
- phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
- phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
- ret_val = e1000_write_phy_reg(hw,
- M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
- } else {
- /* Configure Master and Slave downshift values */
- phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
- phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
- M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
- ret_val = e1000_write_phy_reg(hw,
- M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
- }
- }
-
- /* SW Reset the PHY so all changes take effect */
- ret_val = e1000_phy_reset(hw);
- if (ret_val) {
- DEBUGOUT("Error Resetting the PHY\n");
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
+ /* Call a subroutine to configure the link and setup flow control. */
+ ret_val = e1000_setup_link(hw);
-/********************************************************************
-* Setup auto-negotiation and flow control advertisements,
-* and then perform auto-negotiation.
-*
-* hw - Struct containing variables accessed by shared code
-*********************************************************************/
-static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_copper_link_autoneg");
-
- /* Perform some bounds checking on the hw->autoneg_advertised
- * parameter. If this variable is zero, then set it to the default.
- */
- hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
-
- /* If autoneg_advertised is zero, we assume it was not defaulted
- * by the calling code so we set to advertise full capability.
- */
- if (hw->autoneg_advertised == 0)
- hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
-
- /* IFE phy only supports 10/100 */
- if (hw->phy_type == e1000_phy_ife)
- hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
-
- DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
- ret_val = e1000_phy_setup_autoneg(hw);
- if (ret_val) {
- DEBUGOUT("Error Setting up Auto-Negotiation\n");
- return ret_val;
- }
- DEBUGOUT("Restarting Auto-Neg\n");
-
- /* Restart auto-negotiation by setting the Auto Neg Enable bit and
- * the Auto Neg Restart bit in the PHY control register.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- /* Does the user want to wait for Auto-Neg to complete here, or
- * check at a later time (for example, callback routine).
- */
- if (hw->wait_autoneg_complete) {
- ret_val = e1000_wait_autoneg(hw);
- if (ret_val) {
- DEBUGOUT("Error while waiting for autoneg to complete\n");
- return ret_val;
- }
- }
-
- hw->get_link_status = true;
-
- return E1000_SUCCESS;
-}
+ /* Set the transmit descriptor write-back policy */
+ if (hw->mac_type > e1000_82544) {
+ ctrl = er32(TXDCTL);
+ ctrl =
+ (ctrl & ~E1000_TXDCTL_WTHRESH) |
+ E1000_TXDCTL_FULL_TX_DESC_WB;
+ ew32(TXDCTL, ctrl);
+ }
-/******************************************************************************
-* Config the MAC and the PHY after link is up.
-* 1) Set up the MAC to the current PHY speed/duplex
-* if we are on 82543. If we
-* are on newer silicon, we only need to configure
-* collision distance in the Transmit Control Register.
-* 2) Set up flow control on the MAC to that established with
-* the link partner.
-* 3) Config DSP to improve Gigabit link quality for some PHY revisions.
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_copper_link_postconfig(struct e1000_hw *hw)
-{
- s32 ret_val;
- DEBUGFUNC("e1000_copper_link_postconfig");
-
- if (hw->mac_type >= e1000_82544) {
- e1000_config_collision_dist(hw);
- } else {
- ret_val = e1000_config_mac_to_phy(hw);
- if (ret_val) {
- DEBUGOUT("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
- ret_val = e1000_config_fc_after_link_up(hw);
- if (ret_val) {
- DEBUGOUT("Error Configuring Flow Control\n");
- return ret_val;
- }
-
- /* Config DSP to improve Giga link quality */
- if (hw->phy_type == e1000_phy_igp) {
- ret_val = e1000_config_dsp_after_link_change(hw, true);
- if (ret_val) {
- DEBUGOUT("Error Configuring DSP after link up\n");
- return ret_val;
- }
- }
-
- return E1000_SUCCESS;
-}
+ /* Clear all of the statistics registers (clear on read). It is
+ * important that we do this after we have tried to establish link
+ * because the symbol error count will increment wildly if there
+ * is no link.
+ */
+ e1000_clear_hw_cntrs(hw);
+
+ if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
+ hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
+ ctrl_ext = er32(CTRL_EXT);
+ /* Relaxed ordering must be disabled to avoid a parity
+ * error crash in a PCI slot. */
+ ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
+ ew32(CTRL_EXT, ctrl_ext);
+ }
-/******************************************************************************
-* Detects which PHY is present and setup the speed and duplex
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_setup_copper_link(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 i;
- u16 phy_data;
- u16 reg_data = 0;
-
- DEBUGFUNC("e1000_setup_copper_link");
-
- switch (hw->mac_type) {
- case e1000_80003es2lan:
- case e1000_ich8lan:
- /* Set the mac to wait the maximum time between each
- * iteration and increase the max iterations when
- * polling the phy; this fixes erroneous timeouts at 10Mbps. */
- ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data);
- if (ret_val)
- return ret_val;
- reg_data |= 0x3F;
- ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data);
- if (ret_val)
- return ret_val;
- default:
- break;
- }
-
- /* Check if it is a valid PHY and set PHY mode if necessary. */
- ret_val = e1000_copper_link_preconfig(hw);
- if (ret_val)
- return ret_val;
-
- switch (hw->mac_type) {
- case e1000_80003es2lan:
- /* Kumeran registers are written-only */
- reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
- reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL,
- reg_data);
- if (ret_val)
- return ret_val;
- break;
- default:
- break;
- }
-
- if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) {
- ret_val = e1000_copper_link_igp_setup(hw);
- if (ret_val)
- return ret_val;
- } else if (hw->phy_type == e1000_phy_m88) {
- ret_val = e1000_copper_link_mgp_setup(hw);
- if (ret_val)
- return ret_val;
- } else if (hw->phy_type == e1000_phy_gg82563) {
- ret_val = e1000_copper_link_ggp_setup(hw);
- if (ret_val)
- return ret_val;
- }
-
- if (hw->autoneg) {
- /* Setup autoneg and flow control advertisement
- * and perform autonegotiation */
- ret_val = e1000_copper_link_autoneg(hw);
- if (ret_val)
- return ret_val;
- } else {
- /* PHY will be set to 10H, 10F, 100H,or 100F
- * depending on value from forced_speed_duplex. */
- DEBUGOUT("Forcing speed and duplex\n");
- ret_val = e1000_phy_force_speed_duplex(hw);
- if (ret_val) {
- DEBUGOUT("Error Forcing Speed and Duplex\n");
- return ret_val;
- }
- }
-
- /* Check link status. Wait up to 100 microseconds for link to become
- * valid.
- */
- for (i = 0; i < 10; i++) {
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- if (phy_data & MII_SR_LINK_STATUS) {
- /* Config the MAC and PHY after link is up */
- ret_val = e1000_copper_link_postconfig(hw);
- if (ret_val)
- return ret_val;
-
- DEBUGOUT("Valid link established!!!\n");
- return E1000_SUCCESS;
- }
- udelay(10);
- }
-
- DEBUGOUT("Unable to establish link!!!\n");
- return E1000_SUCCESS;
+ return ret_val;
}
-/******************************************************************************
-* Configure the MAC-to-PHY interface for 10/100Mbps
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex)
+/**
+ * e1000_adjust_serdes_amplitude - Adjust SERDES output amplitude based on EEPROM setting.
+ * @hw: Struct containing variables accessed by shared code.
+ */
+static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw)
{
- s32 ret_val = E1000_SUCCESS;
- u32 tipg;
- u16 reg_data;
-
- DEBUGFUNC("e1000_configure_kmrn_for_10_100");
+ u16 eeprom_data;
+ s32 ret_val;
- reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT;
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
- if (ret_val)
- return ret_val;
+ DEBUGFUNC("e1000_adjust_serdes_amplitude");
- /* Configure Transmit Inter-Packet Gap */
- tipg = er32(TIPG);
- tipg &= ~E1000_TIPG_IPGT_MASK;
- tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100;
- ew32(TIPG, tipg);
+ if (hw->media_type != e1000_media_type_internal_serdes)
+ return E1000_SUCCESS;
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
-
- if (ret_val)
- return ret_val;
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
+ }
- if (duplex == HALF_DUPLEX)
- reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
- else
- reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+ ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1,
+ &eeprom_data);
+ if (ret_val) {
+ return ret_val;
+ }
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+ if (eeprom_data != EEPROM_RESERVED_WORD) {
+ /* Adjust SERDES output amplitude only. */
+ eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data);
+ if (ret_val)
+ return ret_val;
+ }
- return ret_val;
+ return E1000_SUCCESS;
}
-static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw)
+/**
+ * e1000_setup_link - Configures flow control and link settings.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Determines which flow control settings to use. Calls the appropriate media-
+ * specific link configuration function. Configures the flow control settings.
+ * Assuming the adapter has a valid link partner, a valid link should be
+ * established. Assumes the hardware has previously been reset and the
+ * transmitter and receiver are not enabled.
+ */
+s32 e1000_setup_link(struct e1000_hw *hw)
{
- s32 ret_val = E1000_SUCCESS;
- u16 reg_data;
- u32 tipg;
+ u32 ctrl_ext;
+ s32 ret_val;
+ u16 eeprom_data;
- DEBUGFUNC("e1000_configure_kmrn_for_1000");
+ DEBUGFUNC("e1000_setup_link");
- reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT;
- ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL,
- reg_data);
- if (ret_val)
- return ret_val;
+ /* Read and store word 0x0F of the EEPROM. This word contains bits
+ * that determine the hardware's default PAUSE (flow control) mode,
+ * a bit that determines whether the HW defaults to enabling or
+ * disabling auto-negotiation, and the direction of the
+ * SW defined pins. If there is no SW over-ride of the flow
+ * control setting, then the variable hw->fc will
+ * be initialized based on a value in the EEPROM.
+ */
+ if (hw->fc == E1000_FC_DEFAULT) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
+ hw->fc = E1000_FC_NONE;
+ else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
+ EEPROM_WORD0F_ASM_DIR)
+ hw->fc = E1000_FC_TX_PAUSE;
+ else
+ hw->fc = E1000_FC_FULL;
+ }
- /* Configure Transmit Inter-Packet Gap */
- tipg = er32(TIPG);
- tipg &= ~E1000_TIPG_IPGT_MASK;
- tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
- ew32(TIPG, tipg);
+ /* We want to save off the original Flow Control configuration just
+ * in case we get disconnected and then reconnected into a different
+ * hub or switch with different Flow Control capabilities.
+ */
+ if (hw->mac_type == e1000_82542_rev2_0)
+ hw->fc &= (~E1000_FC_TX_PAUSE);
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data);
+ if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
+ hw->fc &= (~E1000_FC_RX_PAUSE);
- if (ret_val)
- return ret_val;
+ hw->original_fc = hw->fc;
- reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+ DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc);
- return ret_val;
-}
+ /* Take the 4 bits from EEPROM word 0x0F that determine the initial
+ * polarity value for the SW controlled pins, and setup the
+ * Extended Device Control reg with that info.
+ * This is needed because one of the SW controlled pins is used for
+ * signal detection. So this should be done before e1000_setup_pcs_link()
+ * or e1000_phy_setup() is called.
+ */
+ if (hw->mac_type == e1000_82543) {
+ ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG,
+ 1, &eeprom_data);
+ if (ret_val) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
+ SWDPIO__EXT_SHIFT);
+ ew32(CTRL_EXT, ctrl_ext);
+ }
-/******************************************************************************
-* Configures PHY autoneg and flow control advertisement settings
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 mii_autoneg_adv_reg;
- u16 mii_1000t_ctrl_reg;
-
- DEBUGFUNC("e1000_phy_setup_autoneg");
-
- /* Read the MII Auto-Neg Advertisement Register (Address 4). */
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
- if (ret_val)
- return ret_val;
-
- if (hw->phy_type != e1000_phy_ife) {
- /* Read the MII 1000Base-T Control Register (Address 9). */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
- if (ret_val)
- return ret_val;
- } else
- mii_1000t_ctrl_reg=0;
-
- /* Need to parse both autoneg_advertised and fc and set up
- * the appropriate PHY registers. First we will parse for
- * autoneg_advertised software override. Since we can advertise
- * a plethora of combinations, we need to check each bit
- * individually.
- */
-
- /* First we clear all the 10/100 mb speed bits in the Auto-Neg
- * Advertisement Register (Address 4) and the 1000 mb speed bits in
- * the 1000Base-T Control Register (Address 9).
- */
- mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
- mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
-
- DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
-
- /* Do we want to advertise 10 Mb Half Duplex? */
- if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
- DEBUGOUT("Advertise 10mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
- }
-
- /* Do we want to advertise 10 Mb Full Duplex? */
- if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
- DEBUGOUT("Advertise 10mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
- }
-
- /* Do we want to advertise 100 Mb Half Duplex? */
- if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
- DEBUGOUT("Advertise 100mb Half duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
- }
-
- /* Do we want to advertise 100 Mb Full Duplex? */
- if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
- DEBUGOUT("Advertise 100mb Full duplex\n");
- mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
- }
-
- /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
- if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
- DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n");
- }
-
- /* Do we want to advertise 1000 Mb Full Duplex? */
- if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
- DEBUGOUT("Advertise 1000mb Full duplex\n");
- mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
- if (hw->phy_type == e1000_phy_ife) {
- DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n");
- }
- }
-
- /* Check for a software override of the flow control settings, and
- * setup the PHY advertisement registers accordingly. If
- * auto-negotiation is enabled, then software will have to set the
- * "PAUSE" bits to the correct value in the Auto-Negotiation
- * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames
- * but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames
- * but we do not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
- * other: No software override. The flow control configuration
- * in the EEPROM is used.
- */
- switch (hw->fc) {
- case E1000_FC_NONE: /* 0 */
- /* Flow control (RX & TX) is completely disabled by a
- * software over-ride.
- */
- mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- case E1000_FC_RX_PAUSE: /* 1 */
- /* RX Flow control is enabled, and TX Flow control is
- * disabled, by a software over-ride.
- */
- /* Since there really isn't a way to advertise that we are
- * capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later
- * (in e1000_config_fc_after_link_up) we will disable the
- *hw's ability to send PAUSE frames.
- */
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- case E1000_FC_TX_PAUSE: /* 2 */
- /* TX Flow control is enabled, and RX Flow control is
- * disabled, by a software over-ride.
- */
- mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
- mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
- break;
- case E1000_FC_FULL: /* 3 */
- /* Flow control (both RX and TX) is enabled by a software
- * over-ride.
- */
- mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
- break;
- default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
- }
-
- ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
- if (ret_val)
- return ret_val;
-
- DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
-
- if (hw->phy_type != e1000_phy_ife) {
- ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
- if (ret_val)
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
+ /* Call the necessary subroutine to configure the link. */
+ ret_val = (hw->media_type == e1000_media_type_copper) ?
+ e1000_setup_copper_link(hw) : e1000_setup_fiber_serdes_link(hw);
-/******************************************************************************
-* Force PHY speed and duplex settings to hw->forced_speed_duplex
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
-{
- u32 ctrl;
- s32 ret_val;
- u16 mii_ctrl_reg;
- u16 mii_status_reg;
- u16 phy_data;
- u16 i;
-
- DEBUGFUNC("e1000_phy_force_speed_duplex");
-
- /* Turn off Flow control if we are forcing speed and duplex. */
- hw->fc = E1000_FC_NONE;
-
- DEBUGOUT1("hw->fc = %d\n", hw->fc);
-
- /* Read the Device Control Register. */
- ctrl = er32(CTRL);
-
- /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ctrl &= ~(DEVICE_SPEED_MASK);
-
- /* Clear the Auto Speed Detect Enable bit. */
- ctrl &= ~E1000_CTRL_ASDE;
-
- /* Read the MII Control Register. */
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
- if (ret_val)
- return ret_val;
-
- /* We need to disable autoneg in order to force link and duplex. */
-
- mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
-
- /* Are we forcing Full or Half Duplex? */
- if (hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_10_full) {
- /* We want to force full duplex so we SET the full duplex bits in the
- * Device and MII Control Registers.
- */
- ctrl |= E1000_CTRL_FD;
- mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
- DEBUGOUT("Full Duplex\n");
- } else {
- /* We want to force half duplex so we CLEAR the full duplex bits in
- * the Device and MII Control Registers.
- */
- ctrl &= ~E1000_CTRL_FD;
- mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
- DEBUGOUT("Half Duplex\n");
- }
-
- /* Are we forcing 100Mbps??? */
- if (hw->forced_speed_duplex == e1000_100_full ||
- hw->forced_speed_duplex == e1000_100_half) {
- /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
- ctrl |= E1000_CTRL_SPD_100;
- mii_ctrl_reg |= MII_CR_SPEED_100;
- mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
- DEBUGOUT("Forcing 100mb ");
- } else {
- /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
- ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
- mii_ctrl_reg |= MII_CR_SPEED_10;
- mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
- DEBUGOUT("Forcing 10mb ");
- }
-
- e1000_config_collision_dist(hw);
-
- /* Write the configured values back to the Device Control Reg. */
- ew32(CTRL, ctrl);
-
- if ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563)) {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
- * forced whenever speed are duplex are forced.
- */
- phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
-
- /* Need to reset the PHY or these changes will be ignored */
- mii_ctrl_reg |= MII_CR_RESET;
-
- /* Disable MDI-X support for 10/100 */
- } else if (hw->phy_type == e1000_phy_ife) {
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IFE_PMC_AUTO_MDIX;
- phy_data &= ~IFE_PMC_FORCE_MDIX;
-
- ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data);
- if (ret_val)
- return ret_val;
-
- } else {
- /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
- * forced whenever speed or duplex are forced.
- */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
- phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
-
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- /* Write back the modified PHY MII control register. */
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
- if (ret_val)
- return ret_val;
-
- udelay(1);
-
- /* The wait_autoneg_complete flag may be a little misleading here.
- * Since we are forcing speed and duplex, Auto-Neg is not enabled.
- * But we do want to delay for a period while forcing only so we
- * don't generate false No Link messages. So we will wait here
- * only if the user has set wait_autoneg_complete to 1, which is
- * the default.
- */
- if (hw->wait_autoneg_complete) {
- /* We will wait for autoneg to complete. */
- DEBUGOUT("Waiting for forced speed/duplex link.\n");
- mii_status_reg = 0;
-
- /* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for (i = PHY_FORCE_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- if (mii_status_reg & MII_SR_LINK_STATUS) break;
- msleep(100);
- }
- if ((i == 0) &&
- ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563))) {
- /* We didn't get link. Reset the DSP and wait again for link. */
- ret_val = e1000_phy_reset_dsp(hw);
- if (ret_val) {
- DEBUGOUT("Error Resetting PHY DSP\n");
- return ret_val;
- }
- }
- /* This loop will early-out if the link condition has been met. */
- for (i = PHY_FORCE_TIME; i > 0; i--) {
- if (mii_status_reg & MII_SR_LINK_STATUS) break;
- msleep(100);
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
- }
- }
-
- if (hw->phy_type == e1000_phy_m88) {
- /* Because we reset the PHY above, we need to re-force TX_CLK in the
- * Extended PHY Specific Control Register to 25MHz clock. This value
- * defaults back to a 2.5MHz clock when the PHY is reset.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= M88E1000_EPSCR_TX_CLK_25;
- ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- /* In addition, because of the s/w reset above, we need to enable CRS on
- * TX. This must be set for both full and half duplex operation.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
- (!hw->autoneg) && (hw->forced_speed_duplex == e1000_10_full ||
- hw->forced_speed_duplex == e1000_10_half)) {
- ret_val = e1000_polarity_reversal_workaround(hw);
- if (ret_val)
- return ret_val;
- }
- } else if (hw->phy_type == e1000_phy_gg82563) {
- /* The TX_CLK of the Extended PHY Specific Control Register defaults
- * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if
- * we're not in a forced 10/duplex configuration. */
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
- if ((hw->forced_speed_duplex == e1000_10_full) ||
- (hw->forced_speed_duplex == e1000_10_half))
- phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ;
- else
- phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ;
-
- /* Also due to the reset, we need to enable CRS on Tx. */
- phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
-
- ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
- if (ret_val)
- return ret_val;
- }
- return E1000_SUCCESS;
+ /* Initialize the flow control address, type, and PAUSE timer
+ * registers to their default values. This is done even if flow
+ * control is disabled, because it does not hurt anything to
+ * initialize these registers.
+ */
+ DEBUGOUT
+ ("Initializing the Flow Control address, type and timer regs\n");
+
+ ew32(FCT, FLOW_CONTROL_TYPE);
+ ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH);
+ ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW);
+
+ ew32(FCTTV, hw->fc_pause_time);
+
+ /* Set the flow control receive threshold registers. Normally,
+ * these registers will be set to a default threshold that may be
+ * adjusted later by the driver's runtime code. However, if the
+ * ability to transmit pause frames in not enabled, then these
+ * registers will be set to 0.
+ */
+ if (!(hw->fc & E1000_FC_TX_PAUSE)) {
+ ew32(FCRTL, 0);
+ ew32(FCRTH, 0);
+ } else {
+ /* We need to set up the Receive Threshold high and low water marks
+ * as well as (optionally) enabling the transmission of XON frames.
+ */
+ if (hw->fc_send_xon) {
+ ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
+ ew32(FCRTH, hw->fc_high_water);
+ } else {
+ ew32(FCRTL, hw->fc_low_water);
+ ew32(FCRTH, hw->fc_high_water);
+ }
+ }
+ return ret_val;
}
-/******************************************************************************
-* Sets the collision distance in the Transmit Control register
-*
-* hw - Struct containing variables accessed by shared code
-*
-* Link should have been established previously. Reads the speed and duplex
-* information from the Device Status register.
-******************************************************************************/
-void e1000_config_collision_dist(struct e1000_hw *hw)
+/**
+ * e1000_setup_fiber_serdes_link - prepare fiber or serdes link
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Manipulates Physical Coding Sublayer functions in order to configure
+ * link. Assumes the hardware has been previously reset and the transmitter
+ * and receiver are not enabled.
+ */
+static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
{
- u32 tctl, coll_dist;
+ u32 ctrl;
+ u32 status;
+ u32 txcw = 0;
+ u32 i;
+ u32 signal = 0;
+ s32 ret_val;
- DEBUGFUNC("e1000_config_collision_dist");
+ DEBUGFUNC("e1000_setup_fiber_serdes_link");
- if (hw->mac_type < e1000_82543)
- coll_dist = E1000_COLLISION_DISTANCE_82542;
- else
- coll_dist = E1000_COLLISION_DISTANCE;
+ /* On adapters with a MAC newer than 82544, SWDP 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ * If we're on serdes media, adjust the output amplitude to value
+ * set in the EEPROM.
+ */
+ ctrl = er32(CTRL);
+ if (hw->media_type == e1000_media_type_fiber)
+ signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+
+ ret_val = e1000_adjust_serdes_amplitude(hw);
+ if (ret_val)
+ return ret_val;
+
+ /* Take the link out of reset */
+ ctrl &= ~(E1000_CTRL_LRST);
+
+ /* Adjust VCO speed to improve BER performance */
+ ret_val = e1000_set_vco_speed(hw);
+ if (ret_val)
+ return ret_val;
+
+ e1000_config_collision_dist(hw);
+
+ /* Check for a software override of the flow control settings, and setup
+ * the device accordingly. If auto-negotiation is enabled, then software
+ * will have to set the "PAUSE" bits to the correct value in the Tranmsit
+ * Config Word Register (TXCW) and re-start auto-negotiation. However, if
+ * auto-negotiation is disabled, then software will have to manually
+ * configure the two flow control enable bits in the CTRL register.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames, but
+ * not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we do
+ * not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ */
+ switch (hw->fc) {
+ case E1000_FC_NONE:
+ /* Flow control is completely disabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
+ break;
+ case E1000_FC_RX_PAUSE:
+ /* RX Flow control is enabled and TX Flow control is disabled by a
+ * software over-ride. Since there really isn't a way to advertise
+ * that we are capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ case E1000_FC_TX_PAUSE:
+ /* TX Flow control is enabled, and RX Flow control is disabled, by a
+ * software over-ride.
+ */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
+ break;
+ case E1000_FC_FULL:
+ /* Flow control (both RX and TX) is enabled by a software over-ride. */
+ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ break;
+ }
+
+ /* Since auto-negotiation is enabled, take the link out of reset (the link
+ * will be in reset, because we previously reset the chip). This will
+ * restart auto-negotiation. If auto-negotiation is successful then the
+ * link-up status bit will be set and the flow control enable bits (RFCE
+ * and TFCE) will be set according to their negotiated value.
+ */
+ DEBUGOUT("Auto-negotiation enabled\n");
- tctl = er32(TCTL);
+ ew32(TXCW, txcw);
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
- tctl &= ~E1000_TCTL_COLD;
- tctl |= coll_dist << E1000_COLD_SHIFT;
+ hw->txcw = txcw;
+ msleep(1);
- ew32(TCTL, tctl);
- E1000_WRITE_FLUSH();
+ /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
+ * indication in the Device Status Register. Time-out if a link isn't
+ * seen in 500 milliseconds seconds (Auto-negotiation should complete in
+ * less than 500 milliseconds even if the other end is doing it in SW).
+ * For internal serdes, we just assume a signal is present, then poll.
+ */
+ if (hw->media_type == e1000_media_type_internal_serdes ||
+ (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) {
+ DEBUGOUT("Looking for Link\n");
+ for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
+ msleep(10);
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU)
+ break;
+ }
+ if (i == (LINK_UP_TIMEOUT / 10)) {
+ DEBUGOUT("Never got a valid link from auto-neg!!!\n");
+ hw->autoneg_failed = 1;
+ /* AutoNeg failed to achieve a link, so we'll call
+ * e1000_check_for_link. This routine will force the link up if
+ * we detect a signal. This will allow us to communicate with
+ * non-autonegotiating link partners.
+ */
+ ret_val = e1000_check_for_link(hw);
+ if (ret_val) {
+ DEBUGOUT("Error while checking for link\n");
+ return ret_val;
+ }
+ hw->autoneg_failed = 0;
+ } else {
+ hw->autoneg_failed = 0;
+ DEBUGOUT("Valid Link Found\n");
+ }
+ } else {
+ DEBUGOUT("No Signal Detected\n");
+ }
+ return E1000_SUCCESS;
}
-/******************************************************************************
-* Sets MAC speed and duplex settings to reflect the those in the PHY
-*
-* hw - Struct containing variables accessed by shared code
-* mii_reg - data to write to the MII control register
-*
-* The contents of the PHY register containing the needed information need to
-* be passed in.
-******************************************************************************/
-static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
-{
- u32 ctrl;
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_config_mac_to_phy");
-
- /* 82544 or newer MAC, Auto Speed Detection takes care of
- * MAC speed/duplex configuration.*/
- if (hw->mac_type >= e1000_82544)
- return E1000_SUCCESS;
-
- /* Read the Device Control Register and set the bits to Force Speed
- * and Duplex.
- */
- ctrl = er32(CTRL);
- ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
- ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
-
- /* Set up duplex in the Device Control and Transmit Control
- * registers depending on negotiated values.
- */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- if (phy_data & M88E1000_PSSR_DPLX)
- ctrl |= E1000_CTRL_FD;
- else
- ctrl &= ~E1000_CTRL_FD;
-
- e1000_config_collision_dist(hw);
-
- /* Set up speed in the Device Control register depending on
- * negotiated values.
- */
- if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
- ctrl |= E1000_CTRL_SPD_1000;
- else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
- ctrl |= E1000_CTRL_SPD_100;
-
- /* Write the configured values back to the Device Control Reg. */
- ew32(CTRL, ctrl);
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * Forces the MAC's flow control settings.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Sets the TFCE and RFCE bits in the device control register to reflect
- * the adapter settings. TFCE and RFCE need to be explicitly set by
- * software when a Copper PHY is used because autonegotiation is managed
- * by the PHY rather than the MAC. Software must also configure these
- * bits when link is forced on a fiber connection.
- *****************************************************************************/
-s32 e1000_force_mac_fc(struct e1000_hw *hw)
-{
- u32 ctrl;
-
- DEBUGFUNC("e1000_force_mac_fc");
-
- /* Get the current configuration of the Device Control Register */
- ctrl = er32(CTRL);
-
- /* Because we didn't get link via the internal auto-negotiation
- * mechanism (we either forced link or we got link via PHY
- * auto-neg), we have to manually enable/disable transmit an
- * receive flow control.
- *
- * The "Case" statement below enables/disable flow control
- * according to the "hw->fc" parameter.
- *
- * The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause
- * frames but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames
- * frames but we do not receive pause frames).
- * 3: Both Rx and TX flow control (symmetric) is enabled.
- * other: No other values should be possible at this point.
- */
-
- switch (hw->fc) {
- case E1000_FC_NONE:
- ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
- break;
- case E1000_FC_RX_PAUSE:
- ctrl &= (~E1000_CTRL_TFCE);
- ctrl |= E1000_CTRL_RFCE;
- break;
- case E1000_FC_TX_PAUSE:
- ctrl &= (~E1000_CTRL_RFCE);
- ctrl |= E1000_CTRL_TFCE;
- break;
- case E1000_FC_FULL:
- ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
- break;
- default:
- DEBUGOUT("Flow control param set incorrectly\n");
- return -E1000_ERR_CONFIG;
- }
-
- /* Disable TX Flow Control for 82542 (rev 2.0) */
- if (hw->mac_type == e1000_82542_rev2_0)
- ctrl &= (~E1000_CTRL_TFCE);
-
- ew32(CTRL, ctrl);
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * Configures flow control settings after link is established
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Should be called immediately after a valid link has been established.
- * Forces MAC flow control settings if link was forced. When in MII/GMII mode
- * and autonegotiation is enabled, the MAC flow control settings will be set
- * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
- * and RFCE bits will be automaticaly set to the negotiated flow control mode.
- *****************************************************************************/
-static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 mii_status_reg;
- u16 mii_nway_adv_reg;
- u16 mii_nway_lp_ability_reg;
- u16 speed;
- u16 duplex;
-
- DEBUGFUNC("e1000_config_fc_after_link_up");
-
- /* Check for the case where we have fiber media and auto-neg failed
- * so we had to force link. In this case, we need to force the
- * configuration of the MAC to match the "fc" parameter.
- */
- if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_internal_serdes) &&
- (hw->autoneg_failed)) ||
- ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) {
- ret_val = e1000_force_mac_fc(hw);
- if (ret_val) {
- DEBUGOUT("Error forcing flow control settings\n");
- return ret_val;
- }
- }
-
- /* Check for the case where we have copper media and auto-neg is
- * enabled. In this case, we need to check and see if Auto-Neg
- * has completed, and if so, how the PHY and link partner has
- * flow control configured.
- */
- if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
- /* Read the MII Status Register and check to see if AutoNeg
- * has completed. We read this twice because this reg has
- * some "sticky" (latched) bits.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
- /* The AutoNeg process has completed, so we now need to
- * read both the Auto Negotiation Advertisement Register
- * (Address 4) and the Auto_Negotiation Base Page Ability
- * Register (Address 5) to determine how flow control was
- * negotiated.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
- &mii_nway_adv_reg);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
- &mii_nway_lp_ability_reg);
- if (ret_val)
- return ret_val;
-
- /* Two bits in the Auto Negotiation Advertisement Register
- * (Address 4) and two bits in the Auto Negotiation Base
- * Page Ability Register (Address 5) determine flow control
- * for both the PHY and the link partner. The following
- * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
- * 1999, describes these PAUSE resolution bits and how flow
- * control is determined based upon these settings.
- * NOTE: DC = Don't Care
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
- *-------|---------|-------|---------|--------------------
- * 0 | 0 | DC | DC | E1000_FC_NONE
- * 0 | 1 | 0 | DC | E1000_FC_NONE
- * 0 | 1 | 1 | 0 | E1000_FC_NONE
- * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
- * 1 | 0 | 0 | DC | E1000_FC_NONE
- * 1 | DC | 1 | DC | E1000_FC_FULL
- * 1 | 1 | 0 | 0 | E1000_FC_NONE
- * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
- *
- */
- /* Are both PAUSE bits set to 1? If so, this implies
- * Symmetric Flow Control is enabled at both ends. The
- * ASM_DIR bits are irrelevant per the spec.
- *
- * For Symmetric Flow Control:
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
- * 1 | DC | 1 | DC | E1000_FC_FULL
- *
- */
- if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
- /* Now we need to check if the user selected RX ONLY
- * of pause frames. In this case, we had to advertise
- * FULL flow control because we could not advertise RX
- * ONLY. Hence, we must now check to see if we need to
- * turn OFF the TRANSMISSION of PAUSE frames.
- */
- if (hw->original_fc == E1000_FC_FULL) {
- hw->fc = E1000_FC_FULL;
- DEBUGOUT("Flow Control = FULL.\n");
- } else {
- hw->fc = E1000_FC_RX_PAUSE;
- DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
- }
- }
- /* For receiving PAUSE frames ONLY.
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
- * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
- *
- */
- else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- hw->fc = E1000_FC_TX_PAUSE;
- DEBUGOUT("Flow Control = TX PAUSE frames only.\n");
- }
- /* For transmitting PAUSE frames ONLY.
- *
- * LOCAL DEVICE | LINK PARTNER
- * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
- * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
- *
- */
- else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
- (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
- !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
- (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
- hw->fc = E1000_FC_RX_PAUSE;
- DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
- }
- /* Per the IEEE spec, at this point flow control should be
- * disabled. However, we want to consider that we could
- * be connected to a legacy switch that doesn't advertise
- * desired flow control, but can be forced on the link
- * partner. So if we advertised no flow control, that is
- * what we will resolve to. If we advertised some kind of
- * receive capability (Rx Pause Only or Full Flow Control)
- * and the link partner advertised none, we will configure
- * ourselves to enable Rx Flow Control only. We can do
- * this safely for two reasons: If the link partner really
- * didn't want flow control enabled, and we enable Rx, no
- * harm done since we won't be receiving any PAUSE frames
- * anyway. If the intent on the link partner was to have
- * flow control enabled, then by us enabling RX only, we
- * can at least receive pause frames and process them.
- * This is a good idea because in most cases, since we are
- * predominantly a server NIC, more times than not we will
- * be asked to delay transmission of packets than asking
- * our link partner to pause transmission of frames.
- */
- else if ((hw->original_fc == E1000_FC_NONE ||
- hw->original_fc == E1000_FC_TX_PAUSE) ||
- hw->fc_strict_ieee) {
- hw->fc = E1000_FC_NONE;
- DEBUGOUT("Flow Control = NONE.\n");
- } else {
- hw->fc = E1000_FC_RX_PAUSE;
- DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
- }
-
- /* Now we need to do one last check... If we auto-
- * negotiated to HALF DUPLEX, flow control should not be
- * enabled per IEEE 802.3 spec.
- */
- ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if (ret_val) {
- DEBUGOUT("Error getting link speed and duplex\n");
- return ret_val;
- }
-
- if (duplex == HALF_DUPLEX)
- hw->fc = E1000_FC_NONE;
-
- /* Now we call a subroutine to actually force the MAC
- * controller to use the correct flow control settings.
- */
- ret_val = e1000_force_mac_fc(hw);
- if (ret_val) {
- DEBUGOUT("Error forcing flow control settings\n");
- return ret_val;
- }
- } else {
- DEBUGOUT("Copper PHY and Auto Neg has not completed.\n");
- }
- }
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * Checks to see if the link status of the hardware has changed.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Called by any function that needs to check the link status of the adapter.
- *****************************************************************************/
-s32 e1000_check_for_link(struct e1000_hw *hw)
-{
- u32 rxcw = 0;
- u32 ctrl;
- u32 status;
- u32 rctl;
- u32 icr;
- u32 signal = 0;
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_check_for_link");
-
- ctrl = er32(CTRL);
- status = er32(STATUS);
-
- /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be
- * set when the optics detect a signal. On older adapters, it will be
- * cleared when there is a signal. This applies to fiber media only.
- */
- if ((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) {
- rxcw = er32(RXCW);
-
- if (hw->media_type == e1000_media_type_fiber) {
- signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
- if (status & E1000_STATUS_LU)
- hw->get_link_status = false;
- }
- }
-
- /* If we have a copper PHY then we only want to go out to the PHY
- * registers to see if Auto-Neg has completed and/or if our link
- * status has changed. The get_link_status flag will be set if we
- * receive a Link Status Change interrupt or we have Rx Sequence
- * Errors.
- */
- if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
- /* First we want to see if the MII Status Register reports
- * link. If so, then we want to get the current speed/duplex
- * of the PHY.
- * Read the register twice since the link bit is sticky.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- if (phy_data & MII_SR_LINK_STATUS) {
- hw->get_link_status = false;
- /* Check if there was DownShift, must be checked immediately after
- * link-up */
- e1000_check_downshift(hw);
-
- /* If we are on 82544 or 82543 silicon and speed/duplex
- * are forced to 10H or 10F, then we will implement the polarity
- * reversal workaround. We disable interrupts first, and upon
- * returning, place the devices interrupt state to its previous
- * value except for the link status change interrupt which will
- * happen due to the execution of this workaround.
- */
-
- if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) &&
- (!hw->autoneg) &&
- (hw->forced_speed_duplex == e1000_10_full ||
- hw->forced_speed_duplex == e1000_10_half)) {
- ew32(IMC, 0xffffffff);
- ret_val = e1000_polarity_reversal_workaround(hw);
- icr = er32(ICR);
- ew32(ICS, (icr & ~E1000_ICS_LSC));
- ew32(IMS, IMS_ENABLE_MASK);
- }
-
- } else {
- /* No link detected */
- e1000_config_dsp_after_link_change(hw, false);
- return 0;
- }
-
- /* If we are forcing speed/duplex, then we simply return since
- * we have already determined whether we have link or not.
- */
- if (!hw->autoneg) return -E1000_ERR_CONFIG;
-
- /* optimize the dsp settings for the igp phy */
- e1000_config_dsp_after_link_change(hw, true);
-
- /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
- * have Si on board that is 82544 or newer, Auto
- * Speed Detection takes care of MAC speed/duplex
- * configuration. So we only need to configure Collision
- * Distance in the MAC. Otherwise, we need to force
- * speed/duplex on the MAC to the current PHY speed/duplex
- * settings.
- */
- if (hw->mac_type >= e1000_82544)
- e1000_config_collision_dist(hw);
- else {
- ret_val = e1000_config_mac_to_phy(hw);
- if (ret_val) {
- DEBUGOUT("Error configuring MAC to PHY settings\n");
- return ret_val;
- }
- }
-
- /* Configure Flow Control now that Auto-Neg has completed. First, we
- * need to restore the desired flow control settings because we may
- * have had to re-autoneg with a different link partner.
- */
- ret_val = e1000_config_fc_after_link_up(hw);
- if (ret_val) {
- DEBUGOUT("Error configuring flow control\n");
- return ret_val;
- }
-
- /* At this point we know that we are on copper and we have
- * auto-negotiated link. These are conditions for checking the link
- * partner capability register. We use the link speed to determine if
- * TBI compatibility needs to be turned on or off. If the link is not
- * at gigabit speed, then TBI compatibility is not needed. If we are
- * at gigabit speed, we turn on TBI compatibility.
- */
- if (hw->tbi_compatibility_en) {
- u16 speed, duplex;
- ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if (ret_val) {
- DEBUGOUT("Error getting link speed and duplex\n");
- return ret_val;
- }
- if (speed != SPEED_1000) {
- /* If link speed is not set to gigabit speed, we do not need
- * to enable TBI compatibility.
- */
- if (hw->tbi_compatibility_on) {
- /* If we previously were in the mode, turn it off. */
- rctl = er32(RCTL);
- rctl &= ~E1000_RCTL_SBP;
- ew32(RCTL, rctl);
- hw->tbi_compatibility_on = false;
- }
- } else {
- /* If TBI compatibility is was previously off, turn it on. For
- * compatibility with a TBI link partner, we will store bad
- * packets. Some frames have an additional byte on the end and
- * will look like CRC errors to the hardware.
- */
- if (!hw->tbi_compatibility_on) {
- hw->tbi_compatibility_on = true;
- rctl = er32(RCTL);
- rctl |= E1000_RCTL_SBP;
- ew32(RCTL, rctl);
- }
- }
- }
- }
- /* If we don't have link (auto-negotiation failed or link partner cannot
- * auto-negotiate), the cable is plugged in (we have signal), and our
- * link partner is not trying to auto-negotiate with us (we are receiving
- * idles or data), we need to force link up. We also need to give
- * auto-negotiation time to complete, in case the cable was just plugged
- * in. The autoneg_failed flag does this.
- */
- else if ((((hw->media_type == e1000_media_type_fiber) &&
- ((ctrl & E1000_CTRL_SWDPIN1) == signal)) ||
- (hw->media_type == e1000_media_type_internal_serdes)) &&
- (!(status & E1000_STATUS_LU)) &&
- (!(rxcw & E1000_RXCW_C))) {
- if (hw->autoneg_failed == 0) {
- hw->autoneg_failed = 1;
- return 0;
- }
- DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n");
-
- /* Disable auto-negotiation in the TXCW register */
- ew32(TXCW, (hw->txcw & ~E1000_TXCW_ANE));
-
- /* Force link-up and also force full-duplex. */
- ctrl = er32(CTRL);
- ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
- ew32(CTRL, ctrl);
-
- /* Configure Flow Control after forcing link up. */
- ret_val = e1000_config_fc_after_link_up(hw);
- if (ret_val) {
- DEBUGOUT("Error configuring flow control\n");
- return ret_val;
- }
- }
- /* If we are forcing link and we are receiving /C/ ordered sets, re-enable
- * auto-negotiation in the TXCW register and disable forced link in the
- * Device Control register in an attempt to auto-negotiate with our link
- * partner.
- */
- else if (((hw->media_type == e1000_media_type_fiber) ||
- (hw->media_type == e1000_media_type_internal_serdes)) &&
- (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
- DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n");
- ew32(TXCW, hw->txcw);
- ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
-
- hw->serdes_link_down = false;
- }
- /* If we force link for non-auto-negotiation switch, check link status
- * based on MAC synchronization for internal serdes media type.
- */
- else if ((hw->media_type == e1000_media_type_internal_serdes) &&
- !(E1000_TXCW_ANE & er32(TXCW))) {
- /* SYNCH bit and IV bit are sticky. */
- udelay(10);
- if (E1000_RXCW_SYNCH & er32(RXCW)) {
- if (!(rxcw & E1000_RXCW_IV)) {
- hw->serdes_link_down = false;
- DEBUGOUT("SERDES: Link is up.\n");
- }
- } else {
- hw->serdes_link_down = true;
- DEBUGOUT("SERDES: Link is down.\n");
- }
- }
- if ((hw->media_type == e1000_media_type_internal_serdes) &&
- (E1000_TXCW_ANE & er32(TXCW))) {
- hw->serdes_link_down = !(E1000_STATUS_LU & er32(STATUS));
- }
- return E1000_SUCCESS;
-}
-
-/******************************************************************************
- * Detects the current speed and duplex settings of the hardware.
+/**
+ * e1000_copper_link_preconfig - early configuration for copper
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- * speed - Speed of the connection
- * duplex - Duplex setting of the connection
- *****************************************************************************/
-s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex)
+ * Make sure we have a valid PHY and change PHY mode before link setup.
+ */
+static s32 e1000_copper_link_preconfig(struct e1000_hw *hw)
{
- u32 status;
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_get_speed_and_duplex");
-
- if (hw->mac_type >= e1000_82543) {
- status = er32(STATUS);
- if (status & E1000_STATUS_SPEED_1000) {
- *speed = SPEED_1000;
- DEBUGOUT("1000 Mbs, ");
- } else if (status & E1000_STATUS_SPEED_100) {
- *speed = SPEED_100;
- DEBUGOUT("100 Mbs, ");
- } else {
- *speed = SPEED_10;
- DEBUGOUT("10 Mbs, ");
- }
-
- if (status & E1000_STATUS_FD) {
- *duplex = FULL_DUPLEX;
- DEBUGOUT("Full Duplex\n");
- } else {
- *duplex = HALF_DUPLEX;
- DEBUGOUT(" Half Duplex\n");
- }
- } else {
- DEBUGOUT("1000 Mbs, Full Duplex\n");
- *speed = SPEED_1000;
- *duplex = FULL_DUPLEX;
- }
-
- /* IGP01 PHY may advertise full duplex operation after speed downgrade even
- * if it is operating at half duplex. Here we set the duplex settings to
- * match the duplex in the link partner's capabilities.
- */
- if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
- ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
- if (ret_val)
- return ret_val;
-
- if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
- *duplex = HALF_DUPLEX;
- else {
- ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
- if (ret_val)
- return ret_val;
- if ((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) ||
- (*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
- *duplex = HALF_DUPLEX;
- }
- }
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (hw->media_type == e1000_media_type_copper)) {
- if (*speed == SPEED_1000)
- ret_val = e1000_configure_kmrn_for_1000(hw);
- else
- ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex);
- if (ret_val)
- return ret_val;
- }
-
- if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) {
- ret_val = e1000_kumeran_lock_loss_workaround(hw);
- if (ret_val)
- return ret_val;
- }
-
- return E1000_SUCCESS;
-}
+ u32 ctrl;
+ s32 ret_val;
+ u16 phy_data;
-/******************************************************************************
-* Blocks until autoneg completes or times out (~4.5 seconds)
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_wait_autoneg(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 i;
- u16 phy_data;
-
- DEBUGFUNC("e1000_wait_autoneg");
- DEBUGOUT("Waiting for Auto-Neg to complete.\n");
-
- /* We will wait for autoneg to complete or 4.5 seconds to expire. */
- for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Auto-Neg
- * Complete bit to be set.
- */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
- if (phy_data & MII_SR_AUTONEG_COMPLETE) {
- return E1000_SUCCESS;
- }
- msleep(100);
- }
- return E1000_SUCCESS;
-}
+ DEBUGFUNC("e1000_copper_link_preconfig");
-/******************************************************************************
-* Raises the Management Data Clock
-*
-* hw - Struct containing variables accessed by shared code
-* ctrl - Device control register's current value
-******************************************************************************/
-static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
-{
- /* Raise the clock input to the Management Data Clock (by setting the MDC
- * bit), and then delay 10 microseconds.
- */
- ew32(CTRL, (*ctrl | E1000_CTRL_MDC));
- E1000_WRITE_FLUSH();
- udelay(10);
-}
+ ctrl = er32(CTRL);
+ /* With 82543, we need to force speed and duplex on the MAC equal to what
+ * the PHY speed and duplex configuration is. In addition, we need to
+ * perform a hardware reset on the PHY to take it out of reset.
+ */
+ if (hw->mac_type > e1000_82543) {
+ ctrl |= E1000_CTRL_SLU;
+ ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ew32(CTRL, ctrl);
+ } else {
+ ctrl |=
+ (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
+ ew32(CTRL, ctrl);
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ }
-/******************************************************************************
-* Lowers the Management Data Clock
-*
-* hw - Struct containing variables accessed by shared code
-* ctrl - Device control register's current value
-******************************************************************************/
-static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
-{
- /* Lower the clock input to the Management Data Clock (by clearing the MDC
- * bit), and then delay 10 microseconds.
- */
- ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC));
- E1000_WRITE_FLUSH();
- udelay(10);
-}
+ /* Make sure we have a valid PHY */
+ ret_val = e1000_detect_gig_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error, did not detect valid phy.\n");
+ return ret_val;
+ }
+ DEBUGOUT1("Phy ID = %x \n", hw->phy_id);
+
+ /* Set PHY to class A mode (if necessary) */
+ ret_val = e1000_set_phy_mode(hw);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82545_rev_3) ||
+ (hw->mac_type == e1000_82546_rev_3)) {
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ phy_data |= 0x00000008;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ }
-/******************************************************************************
-* Shifts data bits out to the PHY
-*
-* hw - Struct containing variables accessed by shared code
-* data - Data to send out to the PHY
-* count - Number of bits to shift out
-*
-* Bits are shifted out in MSB to LSB order.
-******************************************************************************/
-static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count)
-{
- u32 ctrl;
- u32 mask;
-
- /* We need to shift "count" number of bits out to the PHY. So, the value
- * in the "data" parameter will be shifted out to the PHY one bit at a
- * time. In order to do this, "data" must be broken down into bits.
- */
- mask = 0x01;
- mask <<= (count - 1);
-
- ctrl = er32(CTRL);
-
- /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
- ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
-
- while (mask) {
- /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
- * then raising and lowering the Management Data Clock. A "0" is
- * shifted out to the PHY by setting the MDIO bit to "0" and then
- * raising and lowering the clock.
- */
- if (data & mask)
- ctrl |= E1000_CTRL_MDIO;
- else
- ctrl &= ~E1000_CTRL_MDIO;
-
- ew32(CTRL, ctrl);
- E1000_WRITE_FLUSH();
-
- udelay(10);
-
- e1000_raise_mdi_clk(hw, &ctrl);
- e1000_lower_mdi_clk(hw, &ctrl);
-
- mask = mask >> 1;
- }
-}
+ if (hw->mac_type <= e1000_82543 ||
+ hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
+ hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2)
+ hw->phy_reset_disable = false;
-/******************************************************************************
-* Shifts data bits in from the PHY
-*
-* hw - Struct containing variables accessed by shared code
-*
-* Bits are shifted in in MSB to LSB order.
-******************************************************************************/
-static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw)
-{
- u32 ctrl;
- u16 data = 0;
- u8 i;
-
- /* In order to read a register from the PHY, we need to shift in a total
- * of 18 bits from the PHY. The first two bit (turnaround) times are used
- * to avoid contention on the MDIO pin when a read operation is performed.
- * These two bits are ignored by us and thrown away. Bits are "shifted in"
- * by raising the input to the Management Data Clock (setting the MDC bit),
- * and then reading the value of the MDIO bit.
- */
- ctrl = er32(CTRL);
-
- /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
- ctrl &= ~E1000_CTRL_MDIO_DIR;
- ctrl &= ~E1000_CTRL_MDIO;
-
- ew32(CTRL, ctrl);
- E1000_WRITE_FLUSH();
-
- /* Raise and Lower the clock before reading in the data. This accounts for
- * the turnaround bits. The first clock occurred when we clocked out the
- * last bit of the Register Address.
- */
- e1000_raise_mdi_clk(hw, &ctrl);
- e1000_lower_mdi_clk(hw, &ctrl);
-
- for (data = 0, i = 0; i < 16; i++) {
- data = data << 1;
- e1000_raise_mdi_clk(hw, &ctrl);
- ctrl = er32(CTRL);
- /* Check to see if we shifted in a "1". */
- if (ctrl & E1000_CTRL_MDIO)
- data |= 1;
- e1000_lower_mdi_clk(hw, &ctrl);
- }
-
- e1000_raise_mdi_clk(hw, &ctrl);
- e1000_lower_mdi_clk(hw, &ctrl);
-
- return data;
+ return E1000_SUCCESS;
}
-static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask)
+/**
+ * e1000_copper_link_igp_setup - Copper link setup for e1000_phy_igp series.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw)
{
- u32 swfw_sync = 0;
- u32 swmask = mask;
- u32 fwmask = mask << 16;
- s32 timeout = 200;
+ u32 led_ctrl;
+ s32 ret_val;
+ u16 phy_data;
- DEBUGFUNC("e1000_swfw_sync_acquire");
+ DEBUGFUNC("e1000_copper_link_igp_setup");
- if (hw->swfwhw_semaphore_present)
- return e1000_get_software_flag(hw);
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
- if (!hw->swfw_sync_present)
- return e1000_get_hw_eeprom_semaphore(hw);
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
- while (timeout) {
- if (e1000_get_hw_eeprom_semaphore(hw))
- return -E1000_ERR_SWFW_SYNC;
+ /* Wait 15ms for MAC to configure PHY from eeprom settings */
+ msleep(15);
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+
+ /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
+ if (hw->phy_type == e1000_phy_igp) {
+ /* disable lplu d3 during driver init */
+ ret_val = e1000_set_d3_lplu_state(hw, false);
+ if (ret_val) {
+ DEBUGOUT("Error Disabling LPLU D3\n");
+ return ret_val;
+ }
+ }
- swfw_sync = er32(SW_FW_SYNC);
- if (!(swfw_sync & (fwmask | swmask))) {
- break;
- }
+ /* Configure mdi-mdix settings */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ hw->dsp_config_state = e1000_dsp_config_disabled;
+ /* Force MDI for earlier revs of the IGP PHY */
+ phy_data &=
+ ~(IGP01E1000_PSCR_AUTO_MDIX |
+ IGP01E1000_PSCR_FORCE_MDI_MDIX);
+ hw->mdix = 1;
+
+ } else {
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+
+ switch (hw->mdix) {
+ case 1:
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 2:
+ phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
+ break;
+ case 0:
+ default:
+ phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
+ break;
+ }
+ }
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* set auto-master slave resolution settings */
+ if (hw->autoneg) {
+ e1000_ms_type phy_ms_setting = hw->master_slave;
+
+ if (hw->ffe_config_state == e1000_ffe_config_active)
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+
+ if (hw->dsp_config_state == e1000_dsp_config_activated)
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+
+ /* when autonegotiation advertisement is only 1000Mbps then we
+ * should disable SmartSpeed and enable Auto MasterSlave
+ * resolution as hardware default. */
+ if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
+ /* Disable SmartSpeed */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ /* Set auto Master/Slave resolution process */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ ret_val =
+ e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
- /* firmware currently using resource (fwmask) */
- /* or other software thread currently using resource (swmask) */
- e1000_put_hw_eeprom_semaphore(hw);
- mdelay(5);
- timeout--;
- }
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
- if (!timeout) {
- DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n");
- return -E1000_ERR_SWFW_SYNC;
- }
+ /* load defaults for future use */
+ hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
+ ((phy_data & CR_1000T_MS_VALUE) ?
+ e1000_ms_force_master :
+ e1000_ms_force_slave) : e1000_ms_auto;
- swfw_sync |= swmask;
- ew32(SW_FW_SYNC, swfw_sync);
+ switch (phy_ms_setting) {
+ case e1000_ms_force_master:
+ phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_force_slave:
+ phy_data |= CR_1000T_MS_ENABLE;
+ phy_data &= ~(CR_1000T_MS_VALUE);
+ break;
+ case e1000_ms_auto:
+ phy_data &= ~CR_1000T_MS_ENABLE;
+ default:
+ break;
+ }
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
- e1000_put_hw_eeprom_semaphore(hw);
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
-static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask)
+/**
+ * e1000_copper_link_mgp_setup - Copper link setup for e1000_phy_m88 series.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_copper_link_mgp_setup(struct e1000_hw *hw)
{
- u32 swfw_sync;
- u32 swmask = mask;
+ s32 ret_val;
+ u16 phy_data;
- DEBUGFUNC("e1000_swfw_sync_release");
+ DEBUGFUNC("e1000_copper_link_mgp_setup");
- if (hw->swfwhw_semaphore_present) {
- e1000_release_software_flag(hw);
- return;
- }
+ if (hw->phy_reset_disable)
+ return E1000_SUCCESS;
- if (!hw->swfw_sync_present) {
- e1000_put_hw_eeprom_semaphore(hw);
- return;
- }
+ /* Enable CRS on TX. This must be set for half-duplex operation. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
- /* if (e1000_get_hw_eeprom_semaphore(hw))
- * return -E1000_ERR_SWFW_SYNC; */
- while (e1000_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS);
- /* empty */
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
- swfw_sync = er32(SW_FW_SYNC);
- swfw_sync &= ~swmask;
- ew32(SW_FW_SYNC, swfw_sync);
-
- e1000_put_hw_eeprom_semaphore(hw);
-}
-
-/*****************************************************************************
-* Reads the value from a PHY register, if the value is on a specific non zero
-* page, sets the page first.
-* hw - Struct containing variables accessed by shared code
-* reg_addr - address of the PHY register to read
-******************************************************************************/
-s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data)
-{
- u32 ret_val;
- u16 swfw;
-
- DEBUGFUNC("e1000_read_phy_reg");
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw))
- return -E1000_ERR_SWFW_SYNC;
-
- if ((hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) &&
- (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
- ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
- (u16)reg_addr);
- if (ret_val) {
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
- }
- } else if (hw->phy_type == e1000_phy_gg82563) {
- if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) ||
- (hw->mac_type == e1000_80003es2lan)) {
- /* Select Configuration Page */
- if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
- ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- } else {
- /* Use Alternative Page Select register to access
- * registers 30 and 31
- */
- ret_val = e1000_write_phy_reg_ex(hw,
- GG82563_PHY_PAGE_SELECT_ALT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- }
-
- if (ret_val) {
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
- }
- }
- }
-
- ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
- phy_data);
-
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
-}
+ /* Options:
+ * MDI/MDI-X = 0 (default)
+ * 0 - Auto for all speeds
+ * 1 - MDI mode
+ * 2 - MDI-X mode
+ * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
-static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
- u16 *phy_data)
-{
- u32 i;
- u32 mdic = 0;
- const u32 phy_addr = 1;
-
- DEBUGFUNC("e1000_read_phy_reg_ex");
-
- if (reg_addr > MAX_PHY_REG_ADDRESS) {
- DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
- return -E1000_ERR_PARAM;
- }
-
- if (hw->mac_type > e1000_82543) {
- /* Set up Op-code, Phy Address, and register address in the MDI
- * Control register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
- */
- mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
- (phy_addr << E1000_MDIC_PHY_SHIFT) |
- (E1000_MDIC_OP_READ));
-
- ew32(MDIC, mdic);
-
- /* Poll the ready bit to see if the MDI read completed */
- for (i = 0; i < 64; i++) {
- udelay(50);
- mdic = er32(MDIC);
- if (mdic & E1000_MDIC_READY) break;
- }
- if (!(mdic & E1000_MDIC_READY)) {
- DEBUGOUT("MDI Read did not complete\n");
- return -E1000_ERR_PHY;
- }
- if (mdic & E1000_MDIC_ERROR) {
- DEBUGOUT("MDI Error\n");
- return -E1000_ERR_PHY;
- }
- *phy_data = (u16)mdic;
- } else {
- /* We must first send a preamble through the MDIO pin to signal the
- * beginning of an MII instruction. This is done by sending 32
- * consecutive "1" bits.
- */
- e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
-
- /* Now combine the next few fields that are required for a read
- * operation. We use this method instead of calling the
- * e1000_shift_out_mdi_bits routine five different times. The format of
- * a MII read instruction consists of a shift out of 14 bits and is
- * defined as follows:
- * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
- * followed by a shift in of 18 bits. This first two bits shifted in
- * are TurnAround bits used to avoid contention on the MDIO pin when a
- * READ operation is performed. These two bits are thrown away
- * followed by a shift in of 16 bits which contains the desired data.
- */
- mdic = ((reg_addr) | (phy_addr << 5) |
- (PHY_OP_READ << 10) | (PHY_SOF << 12));
-
- e1000_shift_out_mdi_bits(hw, mdic, 14);
-
- /* Now that we've shifted out the read command to the MII, we need to
- * "shift in" the 16-bit value (18 total bits) of the requested PHY
- * register address.
- */
- *phy_data = e1000_shift_in_mdi_bits(hw);
- }
- return E1000_SUCCESS;
-}
+ switch (hw->mdix) {
+ case 1:
+ phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
+ break;
+ case 2:
+ phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
+ break;
+ case 3:
+ phy_data |= M88E1000_PSCR_AUTO_X_1000T;
+ break;
+ case 0:
+ default:
+ phy_data |= M88E1000_PSCR_AUTO_X_MODE;
+ break;
+ }
-/******************************************************************************
-* Writes a value to a PHY register
-*
-* hw - Struct containing variables accessed by shared code
-* reg_addr - address of the PHY register to write
-* data - data to write to the PHY
-******************************************************************************/
-s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 phy_data)
-{
- u32 ret_val;
- u16 swfw;
-
- DEBUGFUNC("e1000_write_phy_reg");
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw))
- return -E1000_ERR_SWFW_SYNC;
-
- if ((hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) &&
- (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
- ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
- (u16)reg_addr);
- if (ret_val) {
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
- }
- } else if (hw->phy_type == e1000_phy_gg82563) {
- if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) ||
- (hw->mac_type == e1000_80003es2lan)) {
- /* Select Configuration Page */
- if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
- ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- } else {
- /* Use Alternative Page Select register to access
- * registers 30 and 31
- */
- ret_val = e1000_write_phy_reg_ex(hw,
- GG82563_PHY_PAGE_SELECT_ALT,
- (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT));
- }
-
- if (ret_val) {
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
- }
- }
- }
-
- ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
- phy_data);
-
- e1000_swfw_sync_release(hw, swfw);
- return ret_val;
-}
+ /* Options:
+ * disable_polarity_correction = 0 (default)
+ * Automatic Correction for Reversed Cable Polarity
+ * 0 - Disabled
+ * 1 - Enabled
+ */
+ phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
+ if (hw->disable_polarity_correction == 1)
+ phy_data |= M88E1000_PSCR_POLARITY_REVERSAL;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy_revision < M88E1011_I_REV_4) {
+ /* Force TX_CLK in the Extended PHY Specific Control Register
+ * to 25MHz clock.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+
+ if ((hw->phy_revision == E1000_REVISION_2) &&
+ (hw->phy_id == M88E1111_I_PHY_ID)) {
+ /* Vidalia Phy, set the downshift counter to 5x */
+ phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
+ phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* Configure Master and Slave downshift values */
+ phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
+ phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X |
+ M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
+ ret_val = e1000_write_phy_reg(hw,
+ M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ }
-static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
- u16 phy_data)
-{
- u32 i;
- u32 mdic = 0;
- const u32 phy_addr = 1;
-
- DEBUGFUNC("e1000_write_phy_reg_ex");
-
- if (reg_addr > MAX_PHY_REG_ADDRESS) {
- DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
- return -E1000_ERR_PARAM;
- }
-
- if (hw->mac_type > e1000_82543) {
- /* Set up Op-code, Phy Address, register address, and data intended
- * for the PHY register in the MDI Control register. The MAC will take
- * care of interfacing with the PHY to send the desired data.
- */
- mdic = (((u32)phy_data) |
- (reg_addr << E1000_MDIC_REG_SHIFT) |
- (phy_addr << E1000_MDIC_PHY_SHIFT) |
- (E1000_MDIC_OP_WRITE));
-
- ew32(MDIC, mdic);
-
- /* Poll the ready bit to see if the MDI read completed */
- for (i = 0; i < 641; i++) {
- udelay(5);
- mdic = er32(MDIC);
- if (mdic & E1000_MDIC_READY) break;
- }
- if (!(mdic & E1000_MDIC_READY)) {
- DEBUGOUT("MDI Write did not complete\n");
- return -E1000_ERR_PHY;
- }
- } else {
- /* We'll need to use the SW defined pins to shift the write command
- * out to the PHY. We first send a preamble to the PHY to signal the
- * beginning of the MII instruction. This is done by sending 32
- * consecutive "1" bits.
- */
- e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
-
- /* Now combine the remaining required fields that will indicate a
- * write operation. We use this method instead of calling the
- * e1000_shift_out_mdi_bits routine for each field in the command. The
- * format of a MII write instruction is as follows:
- * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
- */
- mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
- (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
- mdic <<= 16;
- mdic |= (u32)phy_data;
-
- e1000_shift_out_mdi_bits(hw, mdic, 32);
- }
-
- return E1000_SUCCESS;
-}
+ /* SW Reset the PHY so all changes take effect */
+ ret_val = e1000_phy_reset(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting the PHY\n");
+ return ret_val;
+ }
-static s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 *data)
-{
- u32 reg_val;
- u16 swfw;
- DEBUGFUNC("e1000_read_kmrn_reg");
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw))
- return -E1000_ERR_SWFW_SYNC;
-
- /* Write register address */
- reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
- E1000_KUMCTRLSTA_OFFSET) |
- E1000_KUMCTRLSTA_REN;
- ew32(KUMCTRLSTA, reg_val);
- udelay(2);
-
- /* Read the data returned */
- reg_val = er32(KUMCTRLSTA);
- *data = (u16)reg_val;
-
- e1000_swfw_sync_release(hw, swfw);
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
-static s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 data)
+/**
+ * e1000_copper_link_autoneg - setup auto-neg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Setup auto-negotiation and flow control advertisements,
+ * and then perform auto-negotiation.
+ */
+static s32 e1000_copper_link_autoneg(struct e1000_hw *hw)
{
- u32 reg_val;
- u16 swfw;
- DEBUGFUNC("e1000_write_kmrn_reg");
-
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw))
- return -E1000_ERR_SWFW_SYNC;
-
- reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
- E1000_KUMCTRLSTA_OFFSET) | data;
- ew32(KUMCTRLSTA, reg_val);
- udelay(2);
-
- e1000_swfw_sync_release(hw, swfw);
- return E1000_SUCCESS;
-}
+ s32 ret_val;
+ u16 phy_data;
-/******************************************************************************
-* Returns the PHY to the power-on reset state
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-s32 e1000_phy_hw_reset(struct e1000_hw *hw)
-{
- u32 ctrl, ctrl_ext;
- u32 led_ctrl;
- s32 ret_val;
- u16 swfw;
-
- DEBUGFUNC("e1000_phy_hw_reset");
-
- /* In the case of the phy reset being blocked, it's not an error, we
- * simply return success without performing the reset. */
- ret_val = e1000_check_phy_reset_block(hw);
- if (ret_val)
- return E1000_SUCCESS;
-
- DEBUGOUT("Resetting Phy...\n");
-
- if (hw->mac_type > e1000_82543) {
- if ((hw->mac_type == e1000_80003es2lan) &&
- (er32(STATUS) & E1000_STATUS_FUNC_1)) {
- swfw = E1000_SWFW_PHY1_SM;
- } else {
- swfw = E1000_SWFW_PHY0_SM;
- }
- if (e1000_swfw_sync_acquire(hw, swfw)) {
- DEBUGOUT("Unable to acquire swfw sync\n");
- return -E1000_ERR_SWFW_SYNC;
- }
- /* Read the device control register and assert the E1000_CTRL_PHY_RST
- * bit. Then, take it out of reset.
- * For pre-e1000_82571 hardware, we delay for 10ms between the assert
- * and deassert. For e1000_82571 hardware and later, we instead delay
- * for 50us between and 10ms after the deassertion.
- */
- ctrl = er32(CTRL);
- ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
- E1000_WRITE_FLUSH();
-
- if (hw->mac_type < e1000_82571)
- msleep(10);
- else
- udelay(100);
-
- ew32(CTRL, ctrl);
- E1000_WRITE_FLUSH();
-
- if (hw->mac_type >= e1000_82571)
- mdelay(10);
-
- e1000_swfw_sync_release(hw, swfw);
- } else {
- /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
- * bit to put the PHY into reset. Then, take it out of reset.
- */
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
- ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
- ew32(CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH();
- msleep(10);
- ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
- ew32(CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH();
- }
- udelay(150);
-
- if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
- /* Configure activity LED after PHY reset */
- led_ctrl = er32(LEDCTL);
- led_ctrl &= IGP_ACTIVITY_LED_MASK;
- led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
- ew32(LEDCTL, led_ctrl);
- }
-
- /* Wait for FW to finish PHY configuration. */
- ret_val = e1000_get_phy_cfg_done(hw);
- if (ret_val != E1000_SUCCESS)
- return ret_val;
- e1000_release_software_semaphore(hw);
-
- if ((hw->mac_type == e1000_ich8lan) && (hw->phy_type == e1000_phy_igp_3))
- ret_val = e1000_init_lcd_from_nvm(hw);
-
- return ret_val;
-}
+ DEBUGFUNC("e1000_copper_link_autoneg");
-/******************************************************************************
-* Resets the PHY
-*
-* hw - Struct containing variables accessed by shared code
-*
-* Sets bit 15 of the MII Control register
-******************************************************************************/
-s32 e1000_phy_reset(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_phy_reset");
-
- /* In the case of the phy reset being blocked, it's not an error, we
- * simply return success without performing the reset. */
- ret_val = e1000_check_phy_reset_block(hw);
- if (ret_val)
- return E1000_SUCCESS;
-
- switch (hw->phy_type) {
- case e1000_phy_igp:
- case e1000_phy_igp_2:
- case e1000_phy_igp_3:
- case e1000_phy_ife:
- ret_val = e1000_phy_hw_reset(hw);
- if (ret_val)
- return ret_val;
- break;
- default:
- ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= MII_CR_RESET;
- ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
- if (ret_val)
- return ret_val;
-
- udelay(1);
- break;
- }
-
- if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2)
- e1000_phy_init_script(hw);
-
- return E1000_SUCCESS;
-}
+ /* Perform some bounds checking on the hw->autoneg_advertised
+ * parameter. If this variable is zero, then set it to the default.
+ */
+ hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;
-/******************************************************************************
-* Work-around for 82566 power-down: on D3 entry-
-* 1) disable gigabit link
-* 2) write VR power-down enable
-* 3) read it back
-* if successful continue, else issue LCD reset and repeat
-*
-* hw - struct containing variables accessed by shared code
-******************************************************************************/
-void e1000_phy_powerdown_workaround(struct e1000_hw *hw)
-{
- s32 reg;
- u16 phy_data;
- s32 retry = 0;
+ /* If autoneg_advertised is zero, we assume it was not defaulted
+ * by the calling code so we set to advertise full capability.
+ */
+ if (hw->autoneg_advertised == 0)
+ hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+
+ DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
+ ret_val = e1000_phy_setup_autoneg(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Setting up Auto-Negotiation\n");
+ return ret_val;
+ }
+ DEBUGOUT("Restarting Auto-Neg\n");
- DEBUGFUNC("e1000_phy_powerdown_workaround");
+ /* Restart auto-negotiation by setting the Auto Neg Enable bit and
+ * the Auto Neg Restart bit in the PHY control register.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
- if (hw->phy_type != e1000_phy_igp_3)
- return;
+ phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
- do {
- /* Disable link */
- reg = er32(PHY_CTRL);
- ew32(PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
- E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
+ /* Does the user want to wait for Auto-Neg to complete here, or
+ * check at a later time (for example, callback routine).
+ */
+ if (hw->wait_autoneg_complete) {
+ ret_val = e1000_wait_autoneg(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error while waiting for autoneg to complete\n");
+ return ret_val;
+ }
+ }
- /* Write VR power-down enable - bits 9:8 should be 10b */
- e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
- phy_data |= (1 << 9);
- phy_data &= ~(1 << 8);
- e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data);
+ hw->get_link_status = true;
- /* Read it back and test */
- e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
- if (((phy_data & IGP3_VR_CTRL_MODE_MASK) == IGP3_VR_CTRL_MODE_SHUT) || retry)
- break;
+ return E1000_SUCCESS;
+}
- /* Issue PHY reset and repeat at most one more time */
- reg = er32(CTRL);
- ew32(CTRL, reg | E1000_CTRL_PHY_RST);
- retry++;
- } while (retry);
+/**
+ * e1000_copper_link_postconfig - post link setup
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Config the MAC and the PHY after link is up.
+ * 1) Set up the MAC to the current PHY speed/duplex
+ * if we are on 82543. If we
+ * are on newer silicon, we only need to configure
+ * collision distance in the Transmit Control Register.
+ * 2) Set up flow control on the MAC to that established with
+ * the link partner.
+ * 3) Config DSP to improve Gigabit link quality for some PHY revisions.
+ */
+static s32 e1000_copper_link_postconfig(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ DEBUGFUNC("e1000_copper_link_postconfig");
- return;
+ if (hw->mac_type >= e1000_82544) {
+ e1000_config_collision_dist(hw);
+ } else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring Flow Control\n");
+ return ret_val;
+ }
-}
+ /* Config DSP to improve Giga link quality */
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_config_dsp_after_link_change(hw, true);
+ if (ret_val) {
+ DEBUGOUT("Error Configuring DSP after link up\n");
+ return ret_val;
+ }
+ }
-/******************************************************************************
-* Work-around for 82566 Kumeran PCS lock loss:
-* On link status change (i.e. PCI reset, speed change) and link is up and
-* speed is gigabit-
-* 0) if workaround is optionally disabled do nothing
-* 1) wait 1ms for Kumeran link to come up
-* 2) check Kumeran Diagnostic register PCS lock loss bit
-* 3) if not set the link is locked (all is good), otherwise...
-* 4) reset the PHY
-* 5) repeat up to 10 times
-* Note: this is only called for IGP3 copper when speed is 1gb.
-*
-* hw - struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw)
-{
- s32 ret_val;
- s32 reg;
- s32 cnt;
- u16 phy_data;
-
- if (hw->kmrn_lock_loss_workaround_disabled)
- return E1000_SUCCESS;
-
- /* Make sure link is up before proceeding. If not just return.
- * Attempting this while link is negotiating fouled up link
- * stability */
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
-
- if (phy_data & MII_SR_LINK_STATUS) {
- for (cnt = 0; cnt < 10; cnt++) {
- /* read once to clear */
- ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
- if (ret_val)
- return ret_val;
- /* and again to get new status */
- ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data);
- if (ret_val)
- return ret_val;
-
- /* check for PCS lock */
- if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS))
- return E1000_SUCCESS;
-
- /* Issue PHY reset */
- e1000_phy_hw_reset(hw);
- mdelay(5);
- }
- /* Disable GigE link negotiation */
- reg = er32(PHY_CTRL);
- ew32(PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
- E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
-
- /* unable to acquire PCS lock */
- return E1000_ERR_PHY;
- }
-
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
-/******************************************************************************
-* Probes the expected PHY address for known PHY IDs
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_detect_gig_phy(struct e1000_hw *hw)
+/**
+ * e1000_setup_copper_link - phy/speed/duplex setting
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Detects which PHY is present and sets up the speed and duplex
+ */
+static s32 e1000_setup_copper_link(struct e1000_hw *hw)
{
- s32 phy_init_status, ret_val;
- u16 phy_id_high, phy_id_low;
- bool match = false;
-
- DEBUGFUNC("e1000_detect_gig_phy");
-
- if (hw->phy_id != 0)
- return E1000_SUCCESS;
-
- /* The 82571 firmware may still be configuring the PHY. In this
- * case, we cannot access the PHY until the configuration is done. So
- * we explicitly set the PHY values. */
- if (hw->mac_type == e1000_82571 ||
- hw->mac_type == e1000_82572) {
- hw->phy_id = IGP01E1000_I_PHY_ID;
- hw->phy_type = e1000_phy_igp_2;
- return E1000_SUCCESS;
- }
-
- /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a work-
- * around that forces PHY page 0 to be set or the reads fail. The rest of
- * the code in this routine uses e1000_read_phy_reg to read the PHY ID.
- * So for ESB-2 we need to have this set so our reads won't fail. If the
- * attached PHY is not a e1000_phy_gg82563, the routines below will figure
- * this out as well. */
- if (hw->mac_type == e1000_80003es2lan)
- hw->phy_type = e1000_phy_gg82563;
-
- /* Read the PHY ID Registers to identify which PHY is onboard. */
- ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
- if (ret_val)
- return ret_val;
-
- hw->phy_id = (u32)(phy_id_high << 16);
- udelay(20);
- ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
- if (ret_val)
- return ret_val;
-
- hw->phy_id |= (u32)(phy_id_low & PHY_REVISION_MASK);
- hw->phy_revision = (u32)phy_id_low & ~PHY_REVISION_MASK;
-
- switch (hw->mac_type) {
- case e1000_82543:
- if (hw->phy_id == M88E1000_E_PHY_ID) match = true;
- break;
- case e1000_82544:
- if (hw->phy_id == M88E1000_I_PHY_ID) match = true;
- break;
- case e1000_82540:
- case e1000_82545:
- case e1000_82545_rev_3:
- case e1000_82546:
- case e1000_82546_rev_3:
- if (hw->phy_id == M88E1011_I_PHY_ID) match = true;
- break;
- case e1000_82541:
- case e1000_82541_rev_2:
- case e1000_82547:
- case e1000_82547_rev_2:
- if (hw->phy_id == IGP01E1000_I_PHY_ID) match = true;
- break;
- case e1000_82573:
- if (hw->phy_id == M88E1111_I_PHY_ID) match = true;
- break;
- case e1000_80003es2lan:
- if (hw->phy_id == GG82563_E_PHY_ID) match = true;
- break;
- case e1000_ich8lan:
- if (hw->phy_id == IGP03E1000_E_PHY_ID) match = true;
- if (hw->phy_id == IFE_E_PHY_ID) match = true;
- if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = true;
- if (hw->phy_id == IFE_C_E_PHY_ID) match = true;
- break;
- default:
- DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
- return -E1000_ERR_CONFIG;
- }
- phy_init_status = e1000_set_phy_type(hw);
-
- if ((match) && (phy_init_status == E1000_SUCCESS)) {
- DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
- return E1000_SUCCESS;
- }
- DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
- return -E1000_ERR_PHY;
-}
+ s32 ret_val;
+ u16 i;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_setup_copper_link");
+
+ /* Check if it is a valid PHY and set PHY mode if necessary. */
+ ret_val = e1000_copper_link_preconfig(hw);
+ if (ret_val)
+ return ret_val;
+
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_copper_link_igp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_copper_link_mgp_setup(hw);
+ if (ret_val)
+ return ret_val;
+ }
-/******************************************************************************
-* Resets the PHY's DSP
-*
-* hw - Struct containing variables accessed by shared code
-******************************************************************************/
-static s32 e1000_phy_reset_dsp(struct e1000_hw *hw)
-{
- s32 ret_val;
- DEBUGFUNC("e1000_phy_reset_dsp");
-
- do {
- if (hw->phy_type != e1000_phy_gg82563) {
- ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
- if (ret_val) break;
- }
- ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
- if (ret_val) break;
- ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
- if (ret_val) break;
- ret_val = E1000_SUCCESS;
- } while (0);
-
- return ret_val;
-}
+ if (hw->autoneg) {
+ /* Setup autoneg and flow control advertisement
+ * and perform autonegotiation */
+ ret_val = e1000_copper_link_autoneg(hw);
+ if (ret_val)
+ return ret_val;
+ } else {
+ /* PHY will be set to 10H, 10F, 100H,or 100F
+ * depending on value from forced_speed_duplex. */
+ DEBUGOUT("Forcing speed and duplex\n");
+ ret_val = e1000_phy_force_speed_duplex(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Forcing Speed and Duplex\n");
+ return ret_val;
+ }
+ }
-/******************************************************************************
-* Get PHY information from various PHY registers for igp PHY only.
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
-{
- s32 ret_val;
- u16 phy_data, min_length, max_length, average;
- e1000_rev_polarity polarity;
-
- DEBUGFUNC("e1000_phy_igp_get_info");
-
- /* The downshift status is checked only once, after link is established,
- * and it stored in the hw->speed_downgraded parameter. */
- phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
-
- /* IGP01E1000 does not need to support it. */
- phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
-
- /* IGP01E1000 always correct polarity reversal */
- phy_info->polarity_correction = e1000_polarity_reversal_enabled;
-
- /* Check polarity status */
- ret_val = e1000_check_polarity(hw, &polarity);
- if (ret_val)
- return ret_val;
-
- phy_info->cable_polarity = polarity;
-
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->mdix_mode = (e1000_auto_x_mode)((phy_data & IGP01E1000_PSSR_MDIX) >>
- IGP01E1000_PSSR_MDIX_SHIFT);
-
- if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_1000MBPS) {
- /* Local/Remote Receiver Information are only valid at 1000 Mbps */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
- SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
- e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
- phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
- SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
- e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
-
- /* Get cable length */
- ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
- if (ret_val)
- return ret_val;
-
- /* Translate to old method */
- average = (max_length + min_length) / 2;
-
- if (average <= e1000_igp_cable_length_50)
- phy_info->cable_length = e1000_cable_length_50;
- else if (average <= e1000_igp_cable_length_80)
- phy_info->cable_length = e1000_cable_length_50_80;
- else if (average <= e1000_igp_cable_length_110)
- phy_info->cable_length = e1000_cable_length_80_110;
- else if (average <= e1000_igp_cable_length_140)
- phy_info->cable_length = e1000_cable_length_110_140;
- else
- phy_info->cable_length = e1000_cable_length_140;
- }
-
- return E1000_SUCCESS;
-}
+ /* Check link status. Wait up to 100 microseconds for link to become
+ * valid.
+ */
+ for (i = 0; i < 10; i++) {
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ /* Config the MAC and PHY after link is up */
+ ret_val = e1000_copper_link_postconfig(hw);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT("Valid link established!!!\n");
+ return E1000_SUCCESS;
+ }
+ udelay(10);
+ }
-/******************************************************************************
-* Get PHY information from various PHY registers for ife PHY only.
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-static s32 e1000_phy_ife_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
-{
- s32 ret_val;
- u16 phy_data;
- e1000_rev_polarity polarity;
-
- DEBUGFUNC("e1000_phy_ife_get_info");
-
- phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
- phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
-
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
- phy_info->polarity_correction =
- ((phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >>
- IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT) ?
- e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled;
-
- if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) {
- ret_val = e1000_check_polarity(hw, &polarity);
- if (ret_val)
- return ret_val;
- } else {
- /* Polarity is forced. */
- polarity = ((phy_data & IFE_PSC_FORCE_POLARITY) >>
- IFE_PSC_FORCE_POLARITY_SHIFT) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
- }
- phy_info->cable_polarity = polarity;
-
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->mdix_mode = (e1000_auto_x_mode)
- ((phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >>
- IFE_PMC_MDIX_MODE_SHIFT);
-
- return E1000_SUCCESS;
+ DEBUGOUT("Unable to establish link!!!\n");
+ return E1000_SUCCESS;
}
-/******************************************************************************
-* Get PHY information from various PHY registers fot m88 PHY only.
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
- struct e1000_phy_info *phy_info)
+/**
+ * e1000_phy_setup_autoneg - phy settings
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Configures PHY autoneg and flow control advertisement settings
+ */
+s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
{
- s32 ret_val;
- u16 phy_data;
- e1000_rev_polarity polarity;
-
- DEBUGFUNC("e1000_phy_m88_get_info");
-
- /* The downshift status is checked only once, after link is established,
- * and it stored in the hw->speed_downgraded parameter. */
- phy_info->downshift = (e1000_downshift)hw->speed_downgraded;
-
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->extended_10bt_distance =
- ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >>
- M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ?
- e1000_10bt_ext_dist_enable_lower : e1000_10bt_ext_dist_enable_normal;
-
- phy_info->polarity_correction =
- ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >>
- M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ?
- e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled;
-
- /* Check polarity status */
- ret_val = e1000_check_polarity(hw, &polarity);
- if (ret_val)
- return ret_val;
- phy_info->cable_polarity = polarity;
-
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->mdix_mode = (e1000_auto_x_mode)((phy_data & M88E1000_PSSR_MDIX) >>
- M88E1000_PSSR_MDIX_SHIFT);
-
- if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
- /* Cable Length Estimation and Local/Remote Receiver Information
- * are only valid at 1000 Mbps.
- */
- if (hw->phy_type != e1000_phy_gg82563) {
- phy_info->cable_length = (e1000_cable_length)((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
- M88E1000_PSSR_CABLE_LENGTH_SHIFT);
- } else {
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->cable_length = (e1000_cable_length)(phy_data & GG82563_DSPD_CABLE_LENGTH);
- }
-
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
- SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
- e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
- phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
- SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
- e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
-
- }
-
- return E1000_SUCCESS;
-}
+ s32 ret_val;
+ u16 mii_autoneg_adv_reg;
+ u16 mii_1000t_ctrl_reg;
-/******************************************************************************
-* Get PHY information from various PHY registers
-*
-* hw - Struct containing variables accessed by shared code
-* phy_info - PHY information structure
-******************************************************************************/
-s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info)
-{
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_phy_get_info");
-
- phy_info->cable_length = e1000_cable_length_undefined;
- phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined;
- phy_info->cable_polarity = e1000_rev_polarity_undefined;
- phy_info->downshift = e1000_downshift_undefined;
- phy_info->polarity_correction = e1000_polarity_reversal_undefined;
- phy_info->mdix_mode = e1000_auto_x_mode_undefined;
- phy_info->local_rx = e1000_1000t_rx_status_undefined;
- phy_info->remote_rx = e1000_1000t_rx_status_undefined;
-
- if (hw->media_type != e1000_media_type_copper) {
- DEBUGOUT("PHY info is only valid for copper media\n");
- return -E1000_ERR_CONFIG;
- }
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
- if (ret_val)
- return ret_val;
-
- if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
- DEBUGOUT("PHY info is only valid if link is up\n");
- return -E1000_ERR_CONFIG;
- }
-
- if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2)
- return e1000_phy_igp_get_info(hw, phy_info);
- else if (hw->phy_type == e1000_phy_ife)
- return e1000_phy_ife_get_info(hw, phy_info);
- else
- return e1000_phy_m88_get_info(hw, phy_info);
-}
+ DEBUGFUNC("e1000_phy_setup_autoneg");
-s32 e1000_validate_mdi_setting(struct e1000_hw *hw)
-{
- DEBUGFUNC("e1000_validate_mdi_settings");
-
- if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
- DEBUGOUT("Invalid MDI setting detected\n");
- hw->mdix = 1;
- return -E1000_ERR_CONFIG;
- }
- return E1000_SUCCESS;
-}
+ /* Read the MII Auto-Neg Advertisement Register (Address 4). */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
+ /* Read the MII 1000Base-T Control Register (Address 9). */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
-/******************************************************************************
- * Sets up eeprom variables in the hw struct. Must be called after mac_type
- * is configured. Additionally, if this is ICH8, the flash controller GbE
- * registers must be mapped, or this will crash.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_init_eeprom_params(struct e1000_hw *hw)
-{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u32 eecd = er32(EECD);
- s32 ret_val = E1000_SUCCESS;
- u16 eeprom_size;
-
- DEBUGFUNC("e1000_init_eeprom_params");
-
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- eeprom->type = e1000_eeprom_microwire;
- eeprom->word_size = 64;
- eeprom->opcode_bits = 3;
- eeprom->address_bits = 6;
- eeprom->delay_usec = 50;
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- break;
- case e1000_82540:
- case e1000_82545:
- case e1000_82545_rev_3:
- case e1000_82546:
- case e1000_82546_rev_3:
- eeprom->type = e1000_eeprom_microwire;
- eeprom->opcode_bits = 3;
- eeprom->delay_usec = 50;
- if (eecd & E1000_EECD_SIZE) {
- eeprom->word_size = 256;
- eeprom->address_bits = 8;
- } else {
- eeprom->word_size = 64;
- eeprom->address_bits = 6;
- }
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- break;
- case e1000_82541:
- case e1000_82541_rev_2:
- case e1000_82547:
- case e1000_82547_rev_2:
- if (eecd & E1000_EECD_TYPE) {
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- } else {
- eeprom->type = e1000_eeprom_microwire;
- eeprom->opcode_bits = 3;
- eeprom->delay_usec = 50;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->word_size = 256;
- eeprom->address_bits = 8;
- } else {
- eeprom->word_size = 64;
- eeprom->address_bits = 6;
- }
- }
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- break;
- case e1000_82571:
- case e1000_82572:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- break;
- case e1000_82573:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- eeprom->use_eerd = true;
- eeprom->use_eewr = true;
- if (!e1000_is_onboard_nvm_eeprom(hw)) {
- eeprom->type = e1000_eeprom_flash;
- eeprom->word_size = 2048;
-
- /* Ensure that the Autonomous FLASH update bit is cleared due to
- * Flash update issue on parts which use a FLASH for NVM. */
- eecd &= ~E1000_EECD_AUPDEN;
- ew32(EECD, eecd);
- }
- break;
- case e1000_80003es2lan:
- eeprom->type = e1000_eeprom_spi;
- eeprom->opcode_bits = 8;
- eeprom->delay_usec = 1;
- if (eecd & E1000_EECD_ADDR_BITS) {
- eeprom->page_size = 32;
- eeprom->address_bits = 16;
- } else {
- eeprom->page_size = 8;
- eeprom->address_bits = 8;
- }
- eeprom->use_eerd = true;
- eeprom->use_eewr = false;
- break;
- case e1000_ich8lan:
- {
- s32 i = 0;
- u32 flash_size = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG);
-
- eeprom->type = e1000_eeprom_ich8;
- eeprom->use_eerd = false;
- eeprom->use_eewr = false;
- eeprom->word_size = E1000_SHADOW_RAM_WORDS;
-
- /* Zero the shadow RAM structure. But don't load it from NVM
- * so as to save time for driver init */
- if (hw->eeprom_shadow_ram != NULL) {
- for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
- hw->eeprom_shadow_ram[i].modified = false;
- hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
- }
- }
-
- hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) *
- ICH_FLASH_SECTOR_SIZE;
-
- hw->flash_bank_size = ((flash_size >> 16) & ICH_GFPREG_BASE_MASK) + 1;
- hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK);
-
- hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE;
-
- hw->flash_bank_size /= 2 * sizeof(u16);
-
- break;
- }
- default:
- break;
- }
-
- if (eeprom->type == e1000_eeprom_spi) {
- /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
- * 32KB (incremented by powers of 2).
- */
- if (hw->mac_type <= e1000_82547_rev_2) {
- /* Set to default value for initial eeprom read. */
- eeprom->word_size = 64;
- ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
- if (ret_val)
- return ret_val;
- eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
- /* 256B eeprom size was not supported in earlier hardware, so we
- * bump eeprom_size up one to ensure that "1" (which maps to 256B)
- * is never the result used in the shifting logic below. */
- if (eeprom_size)
- eeprom_size++;
- } else {
- eeprom_size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
- E1000_EECD_SIZE_EX_SHIFT);
- }
-
- eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
- }
- return ret_val;
-}
+ /* Need to parse both autoneg_advertised and fc and set up
+ * the appropriate PHY registers. First we will parse for
+ * autoneg_advertised software override. Since we can advertise
+ * a plethora of combinations, we need to check each bit
+ * individually.
+ */
-/******************************************************************************
- * Raises the EEPROM's clock input.
- *
- * hw - Struct containing variables accessed by shared code
- * eecd - EECD's current value
- *****************************************************************************/
-static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd)
-{
- /* Raise the clock input to the EEPROM (by setting the SK bit), and then
- * wait <delay> microseconds.
- */
- *eecd = *eecd | E1000_EECD_SK;
- ew32(EECD, *eecd);
- E1000_WRITE_FLUSH();
- udelay(hw->eeprom.delay_usec);
-}
+ /* First we clear all the 10/100 mb speed bits in the Auto-Neg
+ * Advertisement Register (Address 4) and the 1000 mb speed bits in
+ * the 1000Base-T Control Register (Address 9).
+ */
+ mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
+ mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
-/******************************************************************************
- * Lowers the EEPROM's clock input.
- *
- * hw - Struct containing variables accessed by shared code
- * eecd - EECD's current value
- *****************************************************************************/
-static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd)
-{
- /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
- * wait 50 microseconds.
- */
- *eecd = *eecd & ~E1000_EECD_SK;
- ew32(EECD, *eecd);
- E1000_WRITE_FLUSH();
- udelay(hw->eeprom.delay_usec);
-}
+ DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised);
-/******************************************************************************
- * Shift data bits out to the EEPROM.
- *
- * hw - Struct containing variables accessed by shared code
- * data - data to send to the EEPROM
- * count - number of bits to shift out
- *****************************************************************************/
-static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count)
-{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u32 eecd;
- u32 mask;
-
- /* We need to shift "count" bits out to the EEPROM. So, value in the
- * "data" parameter will be shifted out to the EEPROM one bit at a time.
- * In order to do this, "data" must be broken down into bits.
- */
- mask = 0x01 << (count - 1);
- eecd = er32(EECD);
- if (eeprom->type == e1000_eeprom_microwire) {
- eecd &= ~E1000_EECD_DO;
- } else if (eeprom->type == e1000_eeprom_spi) {
- eecd |= E1000_EECD_DO;
- }
- do {
- /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
- * and then raising and then lowering the clock (the SK bit controls
- * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
- * by setting "DI" to "0" and then raising and then lowering the clock.
- */
- eecd &= ~E1000_EECD_DI;
-
- if (data & mask)
- eecd |= E1000_EECD_DI;
-
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
-
- udelay(eeprom->delay_usec);
-
- e1000_raise_ee_clk(hw, &eecd);
- e1000_lower_ee_clk(hw, &eecd);
-
- mask = mask >> 1;
-
- } while (mask);
-
- /* We leave the "DI" bit set to "0" when we leave this routine. */
- eecd &= ~E1000_EECD_DI;
- ew32(EECD, eecd);
-}
+ /* Do we want to advertise 10 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
+ DEBUGOUT("Advertise 10mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+ }
-/******************************************************************************
- * Shift data bits in from the EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count)
-{
- u32 eecd;
- u32 i;
- u16 data;
+ /* Do we want to advertise 10 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
+ DEBUGOUT("Advertise 10mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+ }
- /* In order to read a register from the EEPROM, we need to shift 'count'
- * bits in from the EEPROM. Bits are "shifted in" by raising the clock
- * input to the EEPROM (setting the SK bit), and then reading the value of
- * the "DO" bit. During this "shifting in" process the "DI" bit should
- * always be clear.
- */
+ /* Do we want to advertise 100 Mb Half Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
+ DEBUGOUT("Advertise 100mb Half duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+ }
- eecd = er32(EECD);
+ /* Do we want to advertise 100 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
+ DEBUGOUT("Advertise 100mb Full duplex\n");
+ mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+ }
- eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
- data = 0;
+ /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+ if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
+ DEBUGOUT
+ ("Advertise 1000mb Half duplex requested, request denied!\n");
+ }
- for (i = 0; i < count; i++) {
- data = data << 1;
- e1000_raise_ee_clk(hw, &eecd);
+ /* Do we want to advertise 1000 Mb Full Duplex? */
+ if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
+ DEBUGOUT("Advertise 1000mb Full duplex\n");
+ mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+ }
- eecd = er32(EECD);
+ /* Check for a software override of the flow control settings, and
+ * setup the PHY advertisement registers accordingly. If
+ * auto-negotiation is enabled, then software will have to set the
+ * "PAUSE" bits to the correct value in the Auto-Negotiation
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * but we do not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
+ * other: No software override. The flow control configuration
+ * in the EEPROM is used.
+ */
+ switch (hw->fc) {
+ case E1000_FC_NONE: /* 0 */
+ /* Flow control (RX & TX) is completely disabled by a
+ * software over-ride.
+ */
+ mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case E1000_FC_RX_PAUSE: /* 1 */
+ /* RX Flow control is enabled, and TX Flow control is
+ * disabled, by a software over-ride.
+ */
+ /* Since there really isn't a way to advertise that we are
+ * capable of RX Pause ONLY, we will advertise that we
+ * support both symmetric and asymmetric RX PAUSE. Later
+ * (in e1000_config_fc_after_link_up) we will disable the
+ *hw's ability to send PAUSE frames.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ case E1000_FC_TX_PAUSE: /* 2 */
+ /* TX Flow control is enabled, and RX Flow control is
+ * disabled, by a software over-ride.
+ */
+ mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+ mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+ break;
+ case E1000_FC_FULL: /* 3 */
+ /* Flow control (both RX and TX) is enabled by a software
+ * over-ride.
+ */
+ mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
- eecd &= ~(E1000_EECD_DI);
- if (eecd & E1000_EECD_DO)
- data |= 1;
+ ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+ if (ret_val)
+ return ret_val;
- e1000_lower_ee_clk(hw, &eecd);
- }
+ DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
- return data;
-}
+ ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
+ if (ret_val)
+ return ret_val;
-/******************************************************************************
- * Prepares EEPROM for access
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
- * function should be called before issuing a command to the EEPROM.
- *****************************************************************************/
-static s32 e1000_acquire_eeprom(struct e1000_hw *hw)
-{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u32 eecd, i=0;
-
- DEBUGFUNC("e1000_acquire_eeprom");
-
- if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
- return -E1000_ERR_SWFW_SYNC;
- eecd = er32(EECD);
-
- if (hw->mac_type != e1000_82573) {
- /* Request EEPROM Access */
- if (hw->mac_type > e1000_82544) {
- eecd |= E1000_EECD_REQ;
- ew32(EECD, eecd);
- eecd = er32(EECD);
- while ((!(eecd & E1000_EECD_GNT)) &&
- (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
- i++;
- udelay(5);
- eecd = er32(EECD);
- }
- if (!(eecd & E1000_EECD_GNT)) {
- eecd &= ~E1000_EECD_REQ;
- ew32(EECD, eecd);
- DEBUGOUT("Could not acquire EEPROM grant\n");
- e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
- return -E1000_ERR_EEPROM;
- }
- }
- }
-
- /* Setup EEPROM for Read/Write */
-
- if (eeprom->type == e1000_eeprom_microwire) {
- /* Clear SK and DI */
- eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
- ew32(EECD, eecd);
-
- /* Set CS */
- eecd |= E1000_EECD_CS;
- ew32(EECD, eecd);
- } else if (eeprom->type == e1000_eeprom_spi) {
- /* Clear SK and CS */
- eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
- ew32(EECD, eecd);
- udelay(1);
- }
-
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Returns EEPROM to a "standby" state
+/**
+ * e1000_phy_force_speed_duplex - force link settings
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static void e1000_standby_eeprom(struct e1000_hw *hw)
+ * Force PHY speed and duplex settings to hw->forced_speed_duplex
+ */
+static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u32 eecd;
-
- eecd = er32(EECD);
-
- if (eeprom->type == e1000_eeprom_microwire) {
- eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(eeprom->delay_usec);
-
- /* Clock high */
- eecd |= E1000_EECD_SK;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(eeprom->delay_usec);
-
- /* Select EEPROM */
- eecd |= E1000_EECD_CS;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(eeprom->delay_usec);
-
- /* Clock low */
- eecd &= ~E1000_EECD_SK;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(eeprom->delay_usec);
- } else if (eeprom->type == e1000_eeprom_spi) {
- /* Toggle CS to flush commands */
- eecd |= E1000_EECD_CS;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(eeprom->delay_usec);
- eecd &= ~E1000_EECD_CS;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(eeprom->delay_usec);
- }
-}
+ u32 ctrl;
+ s32 ret_val;
+ u16 mii_ctrl_reg;
+ u16 mii_status_reg;
+ u16 phy_data;
+ u16 i;
+
+ DEBUGFUNC("e1000_phy_force_speed_duplex");
+
+ /* Turn off Flow control if we are forcing speed and duplex. */
+ hw->fc = E1000_FC_NONE;
+
+ DEBUGOUT1("hw->fc = %d\n", hw->fc);
+
+ /* Read the Device Control Register. */
+ ctrl = er32(CTRL);
+
+ /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(DEVICE_SPEED_MASK);
+
+ /* Clear the Auto Speed Detect Enable bit. */
+ ctrl &= ~E1000_CTRL_ASDE;
+
+ /* Read the MII Control Register. */
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* We need to disable autoneg in order to force link and duplex. */
+
+ mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN;
+
+ /* Are we forcing Full or Half Duplex? */
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_10_full) {
+ /* We want to force full duplex so we SET the full duplex bits in the
+ * Device and MII Control Registers.
+ */
+ ctrl |= E1000_CTRL_FD;
+ mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ /* We want to force half duplex so we CLEAR the full duplex bits in
+ * the Device and MII Control Registers.
+ */
+ ctrl &= ~E1000_CTRL_FD;
+ mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
+ DEBUGOUT("Half Duplex\n");
+ }
-/******************************************************************************
- * Terminates a command by inverting the EEPROM's chip select pin
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static void e1000_release_eeprom(struct e1000_hw *hw)
-{
- u32 eecd;
+ /* Are we forcing 100Mbps??? */
+ if (hw->forced_speed_duplex == e1000_100_full ||
+ hw->forced_speed_duplex == e1000_100_half) {
+ /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */
+ ctrl |= E1000_CTRL_SPD_100;
+ mii_ctrl_reg |= MII_CR_SPEED_100;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10);
+ DEBUGOUT("Forcing 100mb ");
+ } else {
+ /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */
+ ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ mii_ctrl_reg |= MII_CR_SPEED_10;
+ mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100);
+ DEBUGOUT("Forcing 10mb ");
+ }
- DEBUGFUNC("e1000_release_eeprom");
+ e1000_config_collision_dist(hw);
+
+ /* Write the configured values back to the Device Control Reg. */
+ ew32(CTRL, ctrl);
+
+ if (hw->phy_type == e1000_phy_m88) {
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
+ * forced whenever speed are duplex are forced.
+ */
+ phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data);
+
+ /* Need to reset the PHY or these changes will be ignored */
+ mii_ctrl_reg |= MII_CR_RESET;
+
+ /* Disable MDI-X support for 10/100 */
+ } else {
+ /* Clear Auto-Crossover to force MDI manually. IGP requires MDI
+ * forced whenever speed or duplex are forced.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;
+ phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
+
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+ }
- eecd = er32(EECD);
+ /* Write back the modified PHY MII control register. */
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg);
+ if (ret_val)
+ return ret_val;
- if (hw->eeprom.type == e1000_eeprom_spi) {
- eecd |= E1000_EECD_CS; /* Pull CS high */
- eecd &= ~E1000_EECD_SK; /* Lower SCK */
+ udelay(1);
- ew32(EECD, eecd);
+ /* The wait_autoneg_complete flag may be a little misleading here.
+ * Since we are forcing speed and duplex, Auto-Neg is not enabled.
+ * But we do want to delay for a period while forcing only so we
+ * don't generate false No Link messages. So we will wait here
+ * only if the user has set wait_autoneg_complete to 1, which is
+ * the default.
+ */
+ if (hw->wait_autoneg_complete) {
+ /* We will wait for autoneg to complete. */
+ DEBUGOUT("Waiting for forced speed/duplex link.\n");
+ mii_status_reg = 0;
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ msleep(100);
+ }
+ if ((i == 0) && (hw->phy_type == e1000_phy_m88)) {
+ /* We didn't get link. Reset the DSP and wait again for link. */
+ ret_val = e1000_phy_reset_dsp(hw);
+ if (ret_val) {
+ DEBUGOUT("Error Resetting PHY DSP\n");
+ return ret_val;
+ }
+ }
+ /* This loop will early-out if the link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ msleep(100);
+ /* Read the MII Status Register and wait for Auto-Neg Complete bit
+ * to be set.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ }
+ }
- udelay(hw->eeprom.delay_usec);
- } else if (hw->eeprom.type == e1000_eeprom_microwire) {
- /* cleanup eeprom */
+ if (hw->phy_type == e1000_phy_m88) {
+ /* Because we reset the PHY above, we need to re-force TX_CLK in the
+ * Extended PHY Specific Control Register to 25MHz clock. This value
+ * defaults back to a 2.5MHz clock when the PHY is reset.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_EPSCR_TX_CLK_25;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* In addition, because of the s/w reset above, we need to enable CRS on
+ * TX. This must be set for both full and half duplex operation.
+ */
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543)
+ && (!hw->autoneg)
+ && (hw->forced_speed_duplex == e1000_10_full
+ || hw->forced_speed_duplex == e1000_10_half)) {
+ ret_val = e1000_polarity_reversal_workaround(hw);
+ if (ret_val)
+ return ret_val;
+ }
+ }
+ return E1000_SUCCESS;
+}
- /* CS on Microwire is active-high */
- eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+/**
+ * e1000_config_collision_dist - set collision distance register
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Sets the collision distance in the Transmit Control register.
+ * Link should have been established previously. Reads the speed and duplex
+ * information from the Device Status register.
+ */
+void e1000_config_collision_dist(struct e1000_hw *hw)
+{
+ u32 tctl, coll_dist;
- ew32(EECD, eecd);
+ DEBUGFUNC("e1000_config_collision_dist");
- /* Rising edge of clock */
- eecd |= E1000_EECD_SK;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(hw->eeprom.delay_usec);
+ if (hw->mac_type < e1000_82543)
+ coll_dist = E1000_COLLISION_DISTANCE_82542;
+ else
+ coll_dist = E1000_COLLISION_DISTANCE;
- /* Falling edge of clock */
- eecd &= ~E1000_EECD_SK;
- ew32(EECD, eecd);
- E1000_WRITE_FLUSH();
- udelay(hw->eeprom.delay_usec);
- }
+ tctl = er32(TCTL);
- /* Stop requesting EEPROM access */
- if (hw->mac_type > e1000_82544) {
- eecd &= ~E1000_EECD_REQ;
- ew32(EECD, eecd);
- }
+ tctl &= ~E1000_TCTL_COLD;
+ tctl |= coll_dist << E1000_COLD_SHIFT;
- e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
+ ew32(TCTL, tctl);
+ E1000_WRITE_FLUSH();
}
-/******************************************************************************
- * Reads a 16 bit word from the EEPROM.
+/**
+ * e1000_config_mac_to_phy - sync phy and mac settings
+ * @hw: Struct containing variables accessed by shared code
+ * @mii_reg: data to write to the MII control register
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw)
+ * Sets MAC speed and duplex settings to reflect the those in the PHY
+ * The contents of the PHY register containing the needed information need to
+ * be passed in.
+ */
+static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
{
- u16 retry_count = 0;
- u8 spi_stat_reg;
-
- DEBUGFUNC("e1000_spi_eeprom_ready");
-
- /* Read "Status Register" repeatedly until the LSB is cleared. The
- * EEPROM will signal that the command has been completed by clearing
- * bit 0 of the internal status register. If it's not cleared within
- * 5 milliseconds, then error out.
- */
- retry_count = 0;
- do {
- e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
- hw->eeprom.opcode_bits);
- spi_stat_reg = (u8)e1000_shift_in_ee_bits(hw, 8);
- if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
- break;
-
- udelay(5);
- retry_count += 5;
-
- e1000_standby_eeprom(hw);
- } while (retry_count < EEPROM_MAX_RETRY_SPI);
-
- /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
- * only 0-5mSec on 5V devices)
- */
- if (retry_count >= EEPROM_MAX_RETRY_SPI) {
- DEBUGOUT("SPI EEPROM Status error\n");
- return -E1000_ERR_EEPROM;
- }
-
- return E1000_SUCCESS;
-}
+ u32 ctrl;
+ s32 ret_val;
+ u16 phy_data;
-/******************************************************************************
- * Reads a 16 bit word from the EEPROM.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
-{
- s32 ret;
- spin_lock(&e1000_eeprom_lock);
- ret = e1000_do_read_eeprom(hw, offset, words, data);
- spin_unlock(&e1000_eeprom_lock);
- return ret;
-}
+ DEBUGFUNC("e1000_config_mac_to_phy");
-static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
-{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u32 i = 0;
-
- DEBUGFUNC("e1000_read_eeprom");
-
- /* If eeprom is not yet detected, do so now */
- if (eeprom->word_size == 0)
- e1000_init_eeprom_params(hw);
-
- /* A check for invalid values: offset too large, too many words, and not
- * enough words.
- */
- if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
- (words == 0)) {
- DEBUGOUT2("\"words\" parameter out of bounds. Words = %d, size = %d\n", offset, eeprom->word_size);
- return -E1000_ERR_EEPROM;
- }
-
- /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
- * directly. In this case, we need to acquire the EEPROM so that
- * FW or other port software does not interrupt.
- */
- if (e1000_is_onboard_nvm_eeprom(hw) && !hw->eeprom.use_eerd) {
- /* Prepare the EEPROM for bit-bang reading */
- if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
- }
-
- /* Eerd register EEPROM access requires no eeprom aquire/release */
- if (eeprom->use_eerd)
- return e1000_read_eeprom_eerd(hw, offset, words, data);
-
- /* ICH EEPROM access is done via the ICH flash controller */
- if (eeprom->type == e1000_eeprom_ich8)
- return e1000_read_eeprom_ich8(hw, offset, words, data);
-
- /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
- * acquired the EEPROM at this point, so any returns should relase it */
- if (eeprom->type == e1000_eeprom_spi) {
- u16 word_in;
- u8 read_opcode = EEPROM_READ_OPCODE_SPI;
-
- if (e1000_spi_eeprom_ready(hw)) {
- e1000_release_eeprom(hw);
- return -E1000_ERR_EEPROM;
- }
-
- e1000_standby_eeprom(hw);
-
- /* Some SPI eeproms use the 8th address bit embedded in the opcode */
- if ((eeprom->address_bits == 8) && (offset >= 128))
- read_opcode |= EEPROM_A8_OPCODE_SPI;
-
- /* Send the READ command (opcode + addr) */
- e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
- e1000_shift_out_ee_bits(hw, (u16)(offset*2), eeprom->address_bits);
-
- /* Read the data. The address of the eeprom internally increments with
- * each byte (spi) being read, saving on the overhead of eeprom setup
- * and tear-down. The address counter will roll over if reading beyond
- * the size of the eeprom, thus allowing the entire memory to be read
- * starting from any offset. */
- for (i = 0; i < words; i++) {
- word_in = e1000_shift_in_ee_bits(hw, 16);
- data[i] = (word_in >> 8) | (word_in << 8);
- }
- } else if (eeprom->type == e1000_eeprom_microwire) {
- for (i = 0; i < words; i++) {
- /* Send the READ command (opcode + addr) */
- e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE,
- eeprom->opcode_bits);
- e1000_shift_out_ee_bits(hw, (u16)(offset + i),
- eeprom->address_bits);
-
- /* Read the data. For microwire, each word requires the overhead
- * of eeprom setup and tear-down. */
- data[i] = e1000_shift_in_ee_bits(hw, 16);
- e1000_standby_eeprom(hw);
- }
- }
-
- /* End this read operation */
- e1000_release_eeprom(hw);
-
- return E1000_SUCCESS;
-}
+ /* 82544 or newer MAC, Auto Speed Detection takes care of
+ * MAC speed/duplex configuration.*/
+ if (hw->mac_type >= e1000_82544)
+ return E1000_SUCCESS;
-/******************************************************************************
- * Reads a 16 bit word from the EEPROM using the EERD register.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-static s32 e1000_read_eeprom_eerd(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
-{
- u32 i, eerd = 0;
- s32 error = 0;
+ /* Read the Device Control Register and set the bits to Force Speed
+ * and Duplex.
+ */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+ ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
- for (i = 0; i < words; i++) {
- eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) +
- E1000_EEPROM_RW_REG_START;
+ /* Set up duplex in the Device Control and Transmit Control
+ * registers depending on negotiated values.
+ */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
- ew32(EERD, eerd);
- error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
+ if (phy_data & M88E1000_PSSR_DPLX)
+ ctrl |= E1000_CTRL_FD;
+ else
+ ctrl &= ~E1000_CTRL_FD;
- if (error) {
- break;
- }
- data[i] = (er32(EERD) >> E1000_EEPROM_RW_REG_DATA);
+ e1000_config_collision_dist(hw);
- }
+ /* Set up speed in the Device Control register depending on
+ * negotiated values.
+ */
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+ ctrl |= E1000_CTRL_SPD_1000;
+ else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
+ ctrl |= E1000_CTRL_SPD_100;
- return error;
+ /* Write the configured values back to the Device Control Reg. */
+ ew32(CTRL, ctrl);
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Writes a 16 bit word from the EEPROM using the EEWR register.
+/**
+ * e1000_force_mac_fc - force flow control settings
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
+ * Forces the MAC's flow control settings.
+ * Sets the TFCE and RFCE bits in the device control register to reflect
+ * the adapter settings. TFCE and RFCE need to be explicitly set by
+ * software when a Copper PHY is used because autonegotiation is managed
+ * by the PHY rather than the MAC. Software must also configure these
+ * bits when link is forced on a fiber connection.
+ */
+s32 e1000_force_mac_fc(struct e1000_hw *hw)
{
- u32 register_value = 0;
- u32 i = 0;
- s32 error = 0;
+ u32 ctrl;
+
+ DEBUGFUNC("e1000_force_mac_fc");
+
+ /* Get the current configuration of the Device Control Register */
+ ctrl = er32(CTRL);
+
+ /* Because we didn't get link via the internal auto-negotiation
+ * mechanism (we either forced link or we got link via PHY
+ * auto-neg), we have to manually enable/disable transmit an
+ * receive flow control.
+ *
+ * The "Case" statement below enables/disable flow control
+ * according to the "hw->fc" parameter.
+ *
+ * The possible values of the "fc" parameter are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause
+ * frames but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames
+ * frames but we do not receive pause frames).
+ * 3: Both Rx and TX flow control (symmetric) is enabled.
+ * other: No other values should be possible at this point.
+ */
- if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
- return -E1000_ERR_SWFW_SYNC;
+ switch (hw->fc) {
+ case E1000_FC_NONE:
+ ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
+ break;
+ case E1000_FC_RX_PAUSE:
+ ctrl &= (~E1000_CTRL_TFCE);
+ ctrl |= E1000_CTRL_RFCE;
+ break;
+ case E1000_FC_TX_PAUSE:
+ ctrl &= (~E1000_CTRL_RFCE);
+ ctrl |= E1000_CTRL_TFCE;
+ break;
+ case E1000_FC_FULL:
+ ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
+ break;
+ default:
+ DEBUGOUT("Flow control param set incorrectly\n");
+ return -E1000_ERR_CONFIG;
+ }
- for (i = 0; i < words; i++) {
- register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) |
- ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) |
- E1000_EEPROM_RW_REG_START;
+ /* Disable TX Flow Control for 82542 (rev 2.0) */
+ if (hw->mac_type == e1000_82542_rev2_0)
+ ctrl &= (~E1000_CTRL_TFCE);
- error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
- if (error) {
- break;
- }
+ ew32(CTRL, ctrl);
+ return E1000_SUCCESS;
+}
- ew32(EEWR, register_value);
+/**
+ * e1000_config_fc_after_link_up - configure flow control after autoneg
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Configures flow control settings after link is established
+ * Should be called immediately after a valid link has been established.
+ * Forces MAC flow control settings if link was forced. When in MII/GMII mode
+ * and autonegotiation is enabled, the MAC flow control settings will be set
+ * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
+ * and RFCE bits will be automatically set to the negotiated flow control mode.
+ */
+static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
+{
+ s32 ret_val;
+ u16 mii_status_reg;
+ u16 mii_nway_adv_reg;
+ u16 mii_nway_lp_ability_reg;
+ u16 speed;
+ u16 duplex;
- error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
+ DEBUGFUNC("e1000_config_fc_after_link_up");
- if (error) {
- break;
- }
- }
+ /* Check for the case where we have fiber media and auto-neg failed
+ * so we had to force link. In this case, we need to force the
+ * configuration of the MAC to match the "fc" parameter.
+ */
+ if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_internal_serdes)
+ && (hw->autoneg_failed))
+ || ((hw->media_type == e1000_media_type_copper)
+ && (!hw->autoneg))) {
+ ret_val = e1000_force_mac_fc(hw);
+ if (ret_val) {
+ DEBUGOUT("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
- e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
- return error;
+ /* Check for the case where we have copper media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) {
+ /* Read the MII Status Register and check to see if AutoNeg
+ * has completed. We read this twice because this reg has
+ * some "sticky" (latched) bits.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement Register
+ * (Address 4) and the Auto_Negotiation Base Page Ability
+ * Register (Address 5) to determine how flow control was
+ * negotiated.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
+ &mii_nway_adv_reg);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY,
+ &mii_nway_lp_ability_reg);
+ if (ret_val)
+ return ret_val;
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (Address 4) and two bits in the Auto Negotiation Base
+ * Page Ability Register (Address 5) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | E1000_FC_NONE
+ * 0 | 1 | 0 | DC | E1000_FC_NONE
+ * 0 | 1 | 1 | 0 | E1000_FC_NONE
+ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
+ * 1 | 0 | 0 | DC | E1000_FC_NONE
+ * 1 | DC | 1 | DC | E1000_FC_FULL
+ * 1 | 1 | 0 | 0 | E1000_FC_NONE
+ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
+ *
+ */
+ /* Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | E1000_FC_FULL
+ *
+ */
+ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
+ /* Now we need to check if the user selected RX ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->original_fc == E1000_FC_FULL) {
+ hw->fc = E1000_FC_FULL;
+ DEBUGOUT("Flow Control = FULL.\n");
+ } else {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
+ *
+ */
+ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
+ {
+ hw->fc = E1000_FC_TX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = TX PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
+ *
+ */
+ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
+ (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
+ !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
+ (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
+ {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+ /* Per the IEEE spec, at this point flow control should be
+ * disabled. However, we want to consider that we could
+ * be connected to a legacy switch that doesn't advertise
+ * desired flow control, but can be forced on the link
+ * partner. So if we advertised no flow control, that is
+ * what we will resolve to. If we advertised some kind of
+ * receive capability (Rx Pause Only or Full Flow Control)
+ * and the link partner advertised none, we will configure
+ * ourselves to enable Rx Flow Control only. We can do
+ * this safely for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx, no
+ * harm done since we won't be receiving any PAUSE frames
+ * anyway. If the intent on the link partner was to have
+ * flow control enabled, then by us enabling RX only, we
+ * can at least receive pause frames and process them.
+ * This is a good idea because in most cases, since we are
+ * predominantly a server NIC, more times than not we will
+ * be asked to delay transmission of packets than asking
+ * our link partner to pause transmission of frames.
+ */
+ else if ((hw->original_fc == E1000_FC_NONE ||
+ hw->original_fc == E1000_FC_TX_PAUSE) ||
+ hw->fc_strict_ieee) {
+ hw->fc = E1000_FC_NONE;
+ DEBUGOUT("Flow Control = NONE.\n");
+ } else {
+ hw->fc = E1000_FC_RX_PAUSE;
+ DEBUGOUT
+ ("Flow Control = RX PAUSE frames only.\n");
+ }
+
+ /* Now we need to do one last check... If we auto-
+ * negotiated to HALF DUPLEX, flow control should not be
+ * enabled per IEEE 802.3 spec.
+ */
+ ret_val =
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+
+ if (duplex == HALF_DUPLEX)
+ hw->fc = E1000_FC_NONE;
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ ret_val = e1000_force_mac_fc(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ } else {
+ DEBUGOUT
+ ("Copper PHY and Auto Neg has not completed.\n");
+ }
+ }
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Polls the status bit (bit 1) of the EERD to determine when the read is done.
+/**
+ * e1000_check_for_serdes_link_generic - Check for link (Serdes)
+ * @hw: pointer to the HW structure
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
+ * Checks for link up on the hardware. If link is not up and we have
+ * a signal, then we need to force link up.
+ */
+static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw)
{
- u32 attempts = 100000;
- u32 i, reg = 0;
- s32 done = E1000_ERR_EEPROM;
-
- for (i = 0; i < attempts; i++) {
- if (eerd == E1000_EEPROM_POLL_READ)
- reg = er32(EERD);
- else
- reg = er32(EEWR);
-
- if (reg & E1000_EEPROM_RW_REG_DONE) {
- done = E1000_SUCCESS;
- break;
- }
- udelay(5);
- }
-
- return done;
-}
+ u32 rxcw;
+ u32 ctrl;
+ u32 status;
+ s32 ret_val = E1000_SUCCESS;
-/***************************************************************************
-* Description: Determines if the onboard NVM is FLASH or EEPROM.
-*
-* hw - Struct containing variables accessed by shared code
-****************************************************************************/
-static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
-{
- u32 eecd = 0;
+ DEBUGFUNC("e1000_check_for_serdes_link_generic");
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+ rxcw = er32(RXCW);
- DEBUGFUNC("e1000_is_onboard_nvm_eeprom");
+ /*
+ * If we don't have link (auto-negotiation failed or link partner
+ * cannot auto-negotiate), and our link partner is not trying to
+ * auto-negotiate with us (we are receiving idles or data),
+ * we need to force link up. We also need to give auto-negotiation
+ * time to complete.
+ */
+ /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */
+ if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) {
+ if (hw->autoneg_failed == 0) {
+ hw->autoneg_failed = 1;
+ goto out;
+ }
+ DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n");
- if (hw->mac_type == e1000_ich8lan)
- return false;
+ /* Disable auto-negotiation in the TXCW register */
+ ew32(TXCW, (hw->txcw & ~E1000_TXCW_ANE));
- if (hw->mac_type == e1000_82573) {
- eecd = er32(EECD);
+ /* Force link-up and also force full-duplex. */
+ ctrl = er32(CTRL);
+ ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
+ ew32(CTRL, ctrl);
+
+ /* Configure Flow Control after forcing link up. */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ goto out;
+ }
+ } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
+ /*
+ * If we are forcing link and we are receiving /C/ ordered
+ * sets, re-enable auto-negotiation in the TXCW register
+ * and disable forced link in the Device Control register
+ * in an attempt to auto-negotiate with our link partner.
+ */
+ DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ ew32(TXCW, hw->txcw);
+ ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
+
+ hw->serdes_has_link = true;
+ } else if (!(E1000_TXCW_ANE & er32(TXCW))) {
+ /*
+ * If we force link for non-auto-negotiation switch, check
+ * link status based on MAC synchronization for internal
+ * serdes media type.
+ */
+ /* SYNCH bit and IV bit are sticky. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_has_link = true;
+ DEBUGOUT("SERDES: Link up - forced.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - force failed.\n");
+ }
+ }
- /* Isolate bits 15 & 16 */
- eecd = ((eecd >> 15) & 0x03);
+ if (E1000_TXCW_ANE & er32(TXCW)) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_LU) {
+ /* SYNCH bit and IV bit are sticky, so reread rxcw. */
+ udelay(10);
+ rxcw = er32(RXCW);
+ if (rxcw & E1000_RXCW_SYNCH) {
+ if (!(rxcw & E1000_RXCW_IV)) {
+ hw->serdes_has_link = true;
+ DEBUGOUT("SERDES: Link up - autoneg "
+ "completed successfully.\n");
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - invalid"
+ "codewords detected in autoneg.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - no sync.\n");
+ }
+ } else {
+ hw->serdes_has_link = false;
+ DEBUGOUT("SERDES: Link down - autoneg failed\n");
+ }
+ }
- /* If both bits are set, device is Flash type */
- if (eecd == 0x03) {
- return false;
- }
- }
- return true;
+ out:
+ return ret_val;
}
-/******************************************************************************
- * Verifies that the EEPROM has a valid checksum
+/**
+ * e1000_check_for_link
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- *
- * Reads the first 64 16 bit words of the EEPROM and sums the values read.
- * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
- * valid.
- *****************************************************************************/
-s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw)
+ * Checks to see if the link status of the hardware has changed.
+ * Called by any function that needs to check the link status of the adapter.
+ */
+s32 e1000_check_for_link(struct e1000_hw *hw)
{
- u16 checksum = 0;
- u16 i, eeprom_data;
-
- DEBUGFUNC("e1000_validate_eeprom_checksum");
-
- if ((hw->mac_type == e1000_82573) && !e1000_is_onboard_nvm_eeprom(hw)) {
- /* Check bit 4 of word 10h. If it is 0, firmware is done updating
- * 10h-12h. Checksum may need to be fixed. */
- e1000_read_eeprom(hw, 0x10, 1, &eeprom_data);
- if ((eeprom_data & 0x10) == 0) {
- /* Read 0x23 and check bit 15. This bit is a 1 when the checksum
- * has already been fixed. If the checksum is still wrong and this
- * bit is a 1, we need to return bad checksum. Otherwise, we need
- * to set this bit to a 1 and update the checksum. */
- e1000_read_eeprom(hw, 0x23, 1, &eeprom_data);
- if ((eeprom_data & 0x8000) == 0) {
- eeprom_data |= 0x8000;
- e1000_write_eeprom(hw, 0x23, 1, &eeprom_data);
- e1000_update_eeprom_checksum(hw);
- }
- }
- }
-
- if (hw->mac_type == e1000_ich8lan) {
- /* Drivers must allocate the shadow ram structure for the
- * EEPROM checksum to be updated. Otherwise, this bit as well
- * as the checksum must both be set correctly for this
- * validation to pass.
- */
- e1000_read_eeprom(hw, 0x19, 1, &eeprom_data);
- if ((eeprom_data & 0x40) == 0) {
- eeprom_data |= 0x40;
- e1000_write_eeprom(hw, 0x19, 1, &eeprom_data);
- e1000_update_eeprom_checksum(hw);
- }
- }
-
- for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
- if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- checksum += eeprom_data;
- }
-
- if (checksum == (u16)EEPROM_SUM)
- return E1000_SUCCESS;
- else {
- DEBUGOUT("EEPROM Checksum Invalid\n");
- return -E1000_ERR_EEPROM;
- }
+ u32 rxcw = 0;
+ u32 ctrl;
+ u32 status;
+ u32 rctl;
+ u32 icr;
+ u32 signal = 0;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_for_link");
+
+ ctrl = er32(CTRL);
+ status = er32(STATUS);
+
+ /* On adapters with a MAC newer than 82544, SW Definable pin 1 will be
+ * set when the optics detect a signal. On older adapters, it will be
+ * cleared when there is a signal. This applies to fiber media only.
+ */
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes)) {
+ rxcw = er32(RXCW);
+
+ if (hw->media_type == e1000_media_type_fiber) {
+ signal =
+ (hw->mac_type >
+ e1000_82544) ? E1000_CTRL_SWDPIN1 : 0;
+ if (status & E1000_STATUS_LU)
+ hw->get_link_status = false;
+ }
+ }
+
+ /* If we have a copper PHY then we only want to go out to the PHY
+ * registers to see if Auto-Neg has completed and/or if our link
+ * status has changed. The get_link_status flag will be set if we
+ * receive a Link Status Change interrupt or we have Rx Sequence
+ * Errors.
+ */
+ if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
+ /* First we want to see if the MII Status Register reports
+ * link. If so, then we want to get the current speed/duplex
+ * of the PHY.
+ * Read the register twice since the link bit is sticky.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (phy_data & MII_SR_LINK_STATUS) {
+ hw->get_link_status = false;
+ /* Check if there was DownShift, must be checked immediately after
+ * link-up */
+ e1000_check_downshift(hw);
+
+ /* If we are on 82544 or 82543 silicon and speed/duplex
+ * are forced to 10H or 10F, then we will implement the polarity
+ * reversal workaround. We disable interrupts first, and upon
+ * returning, place the devices interrupt state to its previous
+ * value except for the link status change interrupt which will
+ * happen due to the execution of this workaround.
+ */
+
+ if ((hw->mac_type == e1000_82544
+ || hw->mac_type == e1000_82543) && (!hw->autoneg)
+ && (hw->forced_speed_duplex == e1000_10_full
+ || hw->forced_speed_duplex == e1000_10_half)) {
+ ew32(IMC, 0xffffffff);
+ ret_val =
+ e1000_polarity_reversal_workaround(hw);
+ icr = er32(ICR);
+ ew32(ICS, (icr & ~E1000_ICS_LSC));
+ ew32(IMS, IMS_ENABLE_MASK);
+ }
+
+ } else {
+ /* No link detected */
+ e1000_config_dsp_after_link_change(hw, false);
+ return 0;
+ }
+
+ /* If we are forcing speed/duplex, then we simply return since
+ * we have already determined whether we have link or not.
+ */
+ if (!hw->autoneg)
+ return -E1000_ERR_CONFIG;
+
+ /* optimize the dsp settings for the igp phy */
+ e1000_config_dsp_after_link_change(hw, true);
+
+ /* We have a M88E1000 PHY and Auto-Neg is enabled. If we
+ * have Si on board that is 82544 or newer, Auto
+ * Speed Detection takes care of MAC speed/duplex
+ * configuration. So we only need to configure Collision
+ * Distance in the MAC. Otherwise, we need to force
+ * speed/duplex on the MAC to the current PHY speed/duplex
+ * settings.
+ */
+ if (hw->mac_type >= e1000_82544)
+ e1000_config_collision_dist(hw);
+ else {
+ ret_val = e1000_config_mac_to_phy(hw);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error configuring MAC to PHY settings\n");
+ return ret_val;
+ }
+ }
+
+ /* Configure Flow Control now that Auto-Neg has completed. First, we
+ * need to restore the desired flow control settings because we may
+ * have had to re-autoneg with a different link partner.
+ */
+ ret_val = e1000_config_fc_after_link_up(hw);
+ if (ret_val) {
+ DEBUGOUT("Error configuring flow control\n");
+ return ret_val;
+ }
+
+ /* At this point we know that we are on copper and we have
+ * auto-negotiated link. These are conditions for checking the link
+ * partner capability register. We use the link speed to determine if
+ * TBI compatibility needs to be turned on or off. If the link is not
+ * at gigabit speed, then TBI compatibility is not needed. If we are
+ * at gigabit speed, we turn on TBI compatibility.
+ */
+ if (hw->tbi_compatibility_en) {
+ u16 speed, duplex;
+ ret_val =
+ e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT
+ ("Error getting link speed and duplex\n");
+ return ret_val;
+ }
+ if (speed != SPEED_1000) {
+ /* If link speed is not set to gigabit speed, we do not need
+ * to enable TBI compatibility.
+ */
+ if (hw->tbi_compatibility_on) {
+ /* If we previously were in the mode, turn it off. */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_SBP;
+ ew32(RCTL, rctl);
+ hw->tbi_compatibility_on = false;
+ }
+ } else {
+ /* If TBI compatibility is was previously off, turn it on. For
+ * compatibility with a TBI link partner, we will store bad
+ * packets. Some frames have an additional byte on the end and
+ * will look like CRC errors to to the hardware.
+ */
+ if (!hw->tbi_compatibility_on) {
+ hw->tbi_compatibility_on = true;
+ rctl = er32(RCTL);
+ rctl |= E1000_RCTL_SBP;
+ ew32(RCTL, rctl);
+ }
+ }
+ }
+ }
+
+ if ((hw->media_type == e1000_media_type_fiber) ||
+ (hw->media_type == e1000_media_type_internal_serdes))
+ e1000_check_for_serdes_link_generic(hw);
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Calculates the EEPROM checksum and writes it to the EEPROM
- *
- * hw - Struct containing variables accessed by shared code
- *
- * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA.
- * Writes the difference to word offset 63 of the EEPROM.
- *****************************************************************************/
-s32 e1000_update_eeprom_checksum(struct e1000_hw *hw)
+/**
+ * e1000_get_speed_and_duplex
+ * @hw: Struct containing variables accessed by shared code
+ * @speed: Speed of the connection
+ * @duplex: Duplex setting of the connection
+
+ * Detects the current speed and duplex settings of the hardware.
+ */
+s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex)
{
- u32 ctrl_ext;
- u16 checksum = 0;
- u16 i, eeprom_data;
-
- DEBUGFUNC("e1000_update_eeprom_checksum");
-
- for (i = 0; i < EEPROM_CHECKSUM_REG; i++) {
- if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- checksum += eeprom_data;
- }
- checksum = (u16)EEPROM_SUM - checksum;
- if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
- DEBUGOUT("EEPROM Write Error\n");
- return -E1000_ERR_EEPROM;
- } else if (hw->eeprom.type == e1000_eeprom_flash) {
- e1000_commit_shadow_ram(hw);
- } else if (hw->eeprom.type == e1000_eeprom_ich8) {
- e1000_commit_shadow_ram(hw);
- /* Reload the EEPROM, or else modifications will not appear
- * until after next adapter reset. */
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_EE_RST;
- ew32(CTRL_EXT, ctrl_ext);
- msleep(10);
- }
- return E1000_SUCCESS;
+ u32 status;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_get_speed_and_duplex");
+
+ if (hw->mac_type >= e1000_82543) {
+ status = er32(STATUS);
+ if (status & E1000_STATUS_SPEED_1000) {
+ *speed = SPEED_1000;
+ DEBUGOUT("1000 Mbs, ");
+ } else if (status & E1000_STATUS_SPEED_100) {
+ *speed = SPEED_100;
+ DEBUGOUT("100 Mbs, ");
+ } else {
+ *speed = SPEED_10;
+ DEBUGOUT("10 Mbs, ");
+ }
+
+ if (status & E1000_STATUS_FD) {
+ *duplex = FULL_DUPLEX;
+ DEBUGOUT("Full Duplex\n");
+ } else {
+ *duplex = HALF_DUPLEX;
+ DEBUGOUT(" Half Duplex\n");
+ }
+ } else {
+ DEBUGOUT("1000 Mbs, Full Duplex\n");
+ *speed = SPEED_1000;
+ *duplex = FULL_DUPLEX;
+ }
+
+ /* IGP01 PHY may advertise full duplex operation after speed downgrade even
+ * if it is operating at half duplex. Here we set the duplex settings to
+ * match the duplex in the link partner's capabilities.
+ */
+ if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
+ ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if (!(phy_data & NWAY_ER_LP_NWAY_CAPS))
+ *duplex = HALF_DUPLEX;
+ else {
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if ((*speed == SPEED_100
+ && !(phy_data & NWAY_LPAR_100TX_FD_CAPS))
+ || (*speed == SPEED_10
+ && !(phy_data & NWAY_LPAR_10T_FD_CAPS)))
+ *duplex = HALF_DUPLEX;
+ }
+ }
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Parent function for writing words to the different EEPROM types.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset within the EEPROM to be written to
- * words - number of words to write
- * data - 16 bit word to be written to the EEPROM
+/**
+ * e1000_wait_autoneg
+ * @hw: Struct containing variables accessed by shared code
*
- * If e1000_update_eeprom_checksum is not called after this function, the
- * EEPROM will most likely contain an invalid checksum.
- *****************************************************************************/
-s32 e1000_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+ * Blocks until autoneg completes or times out (~4.5 seconds)
+ */
+static s32 e1000_wait_autoneg(struct e1000_hw *hw)
{
- s32 ret;
- spin_lock(&e1000_eeprom_lock);
- ret = e1000_do_write_eeprom(hw, offset, words, data);
- spin_unlock(&e1000_eeprom_lock);
- return ret;
+ s32 ret_val;
+ u16 i;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_wait_autoneg");
+ DEBUGOUT("Waiting for Auto-Neg to complete.\n");
+
+ /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ for (i = PHY_AUTO_NEG_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Auto-Neg
+ * Complete bit to be set.
+ */
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+ if (phy_data & MII_SR_AUTONEG_COMPLETE) {
+ return E1000_SUCCESS;
+ }
+ msleep(100);
+ }
+ return E1000_SUCCESS;
}
+/**
+ * e1000_raise_mdi_clk - Raises the Management Data Clock
+ * @hw: Struct containing variables accessed by shared code
+ * @ctrl: Device control register's current value
+ */
+static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
+{
+ /* Raise the clock input to the Management Data Clock (by setting the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ ew32(CTRL, (*ctrl | E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH();
+ udelay(10);
+}
-static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+/**
+ * e1000_lower_mdi_clk - Lowers the Management Data Clock
+ * @hw: Struct containing variables accessed by shared code
+ * @ctrl: Device control register's current value
+ */
+static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- s32 status = 0;
-
- DEBUGFUNC("e1000_write_eeprom");
-
- /* If eeprom is not yet detected, do so now */
- if (eeprom->word_size == 0)
- e1000_init_eeprom_params(hw);
-
- /* A check for invalid values: offset too large, too many words, and not
- * enough words.
- */
- if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) ||
- (words == 0)) {
- DEBUGOUT("\"words\" parameter out of bounds\n");
- return -E1000_ERR_EEPROM;
- }
-
- /* 82573 writes only through eewr */
- if (eeprom->use_eewr)
- return e1000_write_eeprom_eewr(hw, offset, words, data);
-
- if (eeprom->type == e1000_eeprom_ich8)
- return e1000_write_eeprom_ich8(hw, offset, words, data);
-
- /* Prepare the EEPROM for writing */
- if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
-
- if (eeprom->type == e1000_eeprom_microwire) {
- status = e1000_write_eeprom_microwire(hw, offset, words, data);
- } else {
- status = e1000_write_eeprom_spi(hw, offset, words, data);
- msleep(10);
- }
-
- /* Done with writing */
- e1000_release_eeprom(hw);
-
- return status;
+ /* Lower the clock input to the Management Data Clock (by clearing the MDC
+ * bit), and then delay 10 microseconds.
+ */
+ ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC));
+ E1000_WRITE_FLUSH();
+ udelay(10);
}
-/******************************************************************************
- * Writes a 16 bit word to a given offset in an SPI EEPROM.
+/**
+ * e1000_shift_out_mdi_bits - Shifts data bits out to the PHY
+ * @hw: Struct containing variables accessed by shared code
+ * @data: Data to send out to the PHY
+ * @count: Number of bits to shift out
*
- * hw - Struct containing variables accessed by shared code
- * offset - offset within the EEPROM to be written to
- * words - number of words to write
- * data - pointer to array of 8 bit words to be written to the EEPROM
- *
- *****************************************************************************/
-static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
+ * Bits are shifted out in MSB to LSB order.
+ */
+static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count)
{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u16 widx = 0;
+ u32 ctrl;
+ u32 mask;
- DEBUGFUNC("e1000_write_eeprom_spi");
+ /* We need to shift "count" number of bits out to the PHY. So, the value
+ * in the "data" parameter will be shifted out to the PHY one bit at a
+ * time. In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01;
+ mask <<= (count - 1);
- while (widx < words) {
- u8 write_opcode = EEPROM_WRITE_OPCODE_SPI;
+ ctrl = er32(CTRL);
- if (e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM;
+ /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */
+ ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
- e1000_standby_eeprom(hw);
+ while (mask) {
+ /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
+ * then raising and lowering the Management Data Clock. A "0" is
+ * shifted out to the PHY by setting the MDIO bit to "0" and then
+ * raising and lowering the clock.
+ */
+ if (data & mask)
+ ctrl |= E1000_CTRL_MDIO;
+ else
+ ctrl &= ~E1000_CTRL_MDIO;
- /* Send the WRITE ENABLE command (8 bit opcode ) */
- e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI,
- eeprom->opcode_bits);
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
- e1000_standby_eeprom(hw);
+ udelay(10);
- /* Some SPI eeproms use the 8th address bit embedded in the opcode */
- if ((eeprom->address_bits == 8) && (offset >= 128))
- write_opcode |= EEPROM_A8_OPCODE_SPI;
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
- /* Send the Write command (8-bit opcode + addr) */
- e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits);
+ mask = mask >> 1;
+ }
+}
- e1000_shift_out_ee_bits(hw, (u16)((offset + widx)*2),
- eeprom->address_bits);
+/**
+ * e1000_shift_in_mdi_bits - Shifts data bits in from the PHY
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Bits are shifted in in MSB to LSB order.
+ */
+static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw)
+{
+ u32 ctrl;
+ u16 data = 0;
+ u8 i;
- /* Send the data */
+ /* In order to read a register from the PHY, we need to shift in a total
+ * of 18 bits from the PHY. The first two bit (turnaround) times are used
+ * to avoid contention on the MDIO pin when a read operation is performed.
+ * These two bits are ignored by us and thrown away. Bits are "shifted in"
+ * by raising the input to the Management Data Clock (setting the MDC bit),
+ * and then reading the value of the MDIO bit.
+ */
+ ctrl = er32(CTRL);
- /* Loop to allow for up to whole page write (32 bytes) of eeprom */
- while (widx < words) {
- u16 word_out = data[widx];
- word_out = (word_out >> 8) | (word_out << 8);
- e1000_shift_out_ee_bits(hw, word_out, 16);
- widx++;
+ /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
+ ctrl &= ~E1000_CTRL_MDIO_DIR;
+ ctrl &= ~E1000_CTRL_MDIO;
- /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
- * operation, while the smaller eeproms are capable of an 8-byte
- * PAGE WRITE operation. Break the inner loop to pass new address
- */
- if ((((offset + widx)*2) % eeprom->page_size) == 0) {
- e1000_standby_eeprom(hw);
- break;
- }
- }
- }
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
- return E1000_SUCCESS;
-}
+ /* Raise and Lower the clock before reading in the data. This accounts for
+ * the turnaround bits. The first clock occurred when we clocked out the
+ * last bit of the Register Address.
+ */
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ for (data = 0, i = 0; i < 16; i++) {
+ data = data << 1;
+ e1000_raise_mdi_clk(hw, &ctrl);
+ ctrl = er32(CTRL);
+ /* Check to see if we shifted in a "1". */
+ if (ctrl & E1000_CTRL_MDIO)
+ data |= 1;
+ e1000_lower_mdi_clk(hw, &ctrl);
+ }
-/******************************************************************************
- * Writes a 16 bit word to a given offset in a Microwire EEPROM.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset within the EEPROM to be written to
- * words - number of words to write
- * data - pointer to array of 16 bit words to be written to the EEPROM
- *
- *****************************************************************************/
-static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
- u16 words, u16 *data)
-{
- struct e1000_eeprom_info *eeprom = &hw->eeprom;
- u32 eecd;
- u16 words_written = 0;
- u16 i = 0;
-
- DEBUGFUNC("e1000_write_eeprom_microwire");
-
- /* Send the write enable command to the EEPROM (3-bit opcode plus
- * 6/8-bit dummy address beginning with 11). It's less work to include
- * the 11 of the dummy address as part of the opcode than it is to shift
- * it over the correct number of bits for the address. This puts the
- * EEPROM into write/erase mode.
- */
- e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE,
- (u16)(eeprom->opcode_bits + 2));
-
- e1000_shift_out_ee_bits(hw, 0, (u16)(eeprom->address_bits - 2));
-
- /* Prepare the EEPROM */
- e1000_standby_eeprom(hw);
-
- while (words_written < words) {
- /* Send the Write command (3-bit opcode + addr) */
- e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE,
- eeprom->opcode_bits);
-
- e1000_shift_out_ee_bits(hw, (u16)(offset + words_written),
- eeprom->address_bits);
-
- /* Send the data */
- e1000_shift_out_ee_bits(hw, data[words_written], 16);
-
- /* Toggle the CS line. This in effect tells the EEPROM to execute
- * the previous command.
- */
- e1000_standby_eeprom(hw);
-
- /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
- * signal that the command has been completed by raising the DO signal.
- * If DO does not go high in 10 milliseconds, then error out.
- */
- for (i = 0; i < 200; i++) {
- eecd = er32(EECD);
- if (eecd & E1000_EECD_DO) break;
- udelay(50);
- }
- if (i == 200) {
- DEBUGOUT("EEPROM Write did not complete\n");
- return -E1000_ERR_EEPROM;
- }
-
- /* Recover from write */
- e1000_standby_eeprom(hw);
-
- words_written++;
- }
-
- /* Send the write disable command to the EEPROM (3-bit opcode plus
- * 6/8-bit dummy address beginning with 10). It's less work to include
- * the 10 of the dummy address as part of the opcode than it is to shift
- * it over the correct number of bits for the address. This takes the
- * EEPROM out of write/erase mode.
- */
- e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE,
- (u16)(eeprom->opcode_bits + 2));
-
- e1000_shift_out_ee_bits(hw, 0, (u16)(eeprom->address_bits - 2));
-
- return E1000_SUCCESS;
+ e1000_raise_mdi_clk(hw, &ctrl);
+ e1000_lower_mdi_clk(hw, &ctrl);
+
+ return data;
}
-/******************************************************************************
- * Flushes the cached eeprom to NVM. This is done by saving the modified values
- * in the eeprom cache and the non modified values in the currently active bank
- * to the new bank.
+
+/**
+ * e1000_read_phy_reg - read a phy register
+ * @hw: Struct containing variables accessed by shared code
+ * @reg_addr: address of the PHY register to read
*
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-static s32 e1000_commit_shadow_ram(struct e1000_hw *hw)
+ * Reads the value from a PHY register, if the value is on a specific non zero
+ * page, sets the page first.
+ */
+s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data)
{
- u32 attempts = 100000;
- u32 eecd = 0;
- u32 flop = 0;
- u32 i = 0;
- s32 error = E1000_SUCCESS;
- u32 old_bank_offset = 0;
- u32 new_bank_offset = 0;
- u8 low_byte = 0;
- u8 high_byte = 0;
- bool sector_write_failed = false;
-
- if (hw->mac_type == e1000_82573) {
- /* The flop register will be used to determine if flash type is STM */
- flop = er32(FLOP);
- for (i=0; i < attempts; i++) {
- eecd = er32(EECD);
- if ((eecd & E1000_EECD_FLUPD) == 0) {
- break;
- }
- udelay(5);
- }
-
- if (i == attempts) {
- return -E1000_ERR_EEPROM;
- }
-
- /* If STM opcode located in bits 15:8 of flop, reset firmware */
- if ((flop & 0xFF00) == E1000_STM_OPCODE) {
- ew32(HICR, E1000_HICR_FW_RESET);
- }
-
- /* Perform the flash update */
- ew32(EECD, eecd | E1000_EECD_FLUPD);
-
- for (i=0; i < attempts; i++) {
- eecd = er32(EECD);
- if ((eecd & E1000_EECD_FLUPD) == 0) {
- break;
- }
- udelay(5);
- }
-
- if (i == attempts) {
- return -E1000_ERR_EEPROM;
- }
- }
-
- if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) {
- /* We're writing to the opposite bank so if we're on bank 1,
- * write to bank 0 etc. We also need to erase the segment that
- * is going to be written */
- if (!(er32(EECD) & E1000_EECD_SEC1VAL)) {
- new_bank_offset = hw->flash_bank_size * 2;
- old_bank_offset = 0;
- e1000_erase_ich8_4k_segment(hw, 1);
- } else {
- old_bank_offset = hw->flash_bank_size * 2;
- new_bank_offset = 0;
- e1000_erase_ich8_4k_segment(hw, 0);
- }
-
- sector_write_failed = false;
- /* Loop for every byte in the shadow RAM,
- * which is in units of words. */
- for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
- /* Determine whether to write the value stored
- * in the other NVM bank or a modified value stored
- * in the shadow RAM */
- if (hw->eeprom_shadow_ram[i].modified) {
- low_byte = (u8)hw->eeprom_shadow_ram[i].eeprom_word;
- udelay(100);
- error = e1000_verify_write_ich8_byte(hw,
- (i << 1) + new_bank_offset, low_byte);
-
- if (error != E1000_SUCCESS)
- sector_write_failed = true;
- else {
- high_byte =
- (u8)(hw->eeprom_shadow_ram[i].eeprom_word >> 8);
- udelay(100);
- }
- } else {
- e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset,
- &low_byte);
- udelay(100);
- error = e1000_verify_write_ich8_byte(hw,
- (i << 1) + new_bank_offset, low_byte);
-
- if (error != E1000_SUCCESS)
- sector_write_failed = true;
- else {
- e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1,
- &high_byte);
- udelay(100);
- }
- }
-
- /* If the write of the low byte was successful, go ahead and
- * write the high byte while checking to make sure that if it
- * is the signature byte, then it is handled properly */
- if (!sector_write_failed) {
- /* If the word is 0x13, then make sure the signature bits
- * (15:14) are 11b until the commit has completed.
- * This will allow us to write 10b which indicates the
- * signature is valid. We want to do this after the write
- * has completed so that we don't mark the segment valid
- * while the write is still in progress */
- if (i == E1000_ICH_NVM_SIG_WORD)
- high_byte = E1000_ICH_NVM_SIG_MASK | high_byte;
-
- error = e1000_verify_write_ich8_byte(hw,
- (i << 1) + new_bank_offset + 1, high_byte);
- if (error != E1000_SUCCESS)
- sector_write_failed = true;
-
- } else {
- /* If the write failed then break from the loop and
- * return an error */
- break;
- }
- }
-
- /* Don't bother writing the segment valid bits if sector
- * programming failed. */
- if (!sector_write_failed) {
- /* Finally validate the new segment by setting bit 15:14
- * to 10b in word 0x13 , this can be done without an
- * erase as well since these bits are 11 to start with
- * and we need to change bit 14 to 0b */
- e1000_read_ich8_byte(hw,
- E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset,
- &high_byte);
- high_byte &= 0xBF;
- error = e1000_verify_write_ich8_byte(hw,
- E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, high_byte);
- /* And invalidate the previously valid segment by setting
- * its signature word (0x13) high_byte to 0b. This can be
- * done without an erase because flash erase sets all bits
- * to 1's. We can write 1's to 0's without an erase */
- if (error == E1000_SUCCESS) {
- error = e1000_verify_write_ich8_byte(hw,
- E1000_ICH_NVM_SIG_WORD * 2 + 1 + old_bank_offset, 0);
- }
-
- /* Clear the now not used entry in the cache */
- for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) {
- hw->eeprom_shadow_ram[i].modified = false;
- hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF;
- }
- }
- }
-
- return error;
+ u32 ret_val;
+
+ DEBUGFUNC("e1000_read_phy_reg");
+
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (u16) reg_addr);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ return ret_val;
}
-/******************************************************************************
- * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
- * second function of dual function devices
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_read_mac_addr(struct e1000_hw *hw)
+static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 *phy_data)
{
- u16 offset;
- u16 eeprom_data, i;
-
- DEBUGFUNC("e1000_read_mac_addr");
-
- for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
- offset = i >> 1;
- if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
- hw->perm_mac_addr[i] = (u8)(eeprom_data & 0x00FF);
- hw->perm_mac_addr[i+1] = (u8)(eeprom_data >> 8);
- }
-
- switch (hw->mac_type) {
- default:
- break;
- case e1000_82546:
- case e1000_82546_rev_3:
- case e1000_82571:
- case e1000_80003es2lan:
- if (er32(STATUS) & E1000_STATUS_FUNC_1)
- hw->perm_mac_addr[5] ^= 0x01;
- break;
- }
-
- for (i = 0; i < NODE_ADDRESS_SIZE; i++)
- hw->mac_addr[i] = hw->perm_mac_addr[i];
- return E1000_SUCCESS;
+ u32 i;
+ u32 mdic = 0;
+ const u32 phy_addr = 1;
+
+ DEBUGFUNC("e1000_read_phy_reg_ex");
+
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if (hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, and register address in the MDI
+ * Control register. The MAC will take care of interfacing with the
+ * PHY to retrieve the desired data.
+ */
+ mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_READ));
+
+ ew32(MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < 64; i++) {
+ udelay(50);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Read did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ if (mdic & E1000_MDIC_ERROR) {
+ DEBUGOUT("MDI Error\n");
+ return -E1000_ERR_PHY;
+ }
+ *phy_data = (u16) mdic;
+ } else {
+ /* We must first send a preamble through the MDIO pin to signal the
+ * beginning of an MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the next few fields that are required for a read
+ * operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine five different times. The format of
+ * a MII read instruction consists of a shift out of 14 bits and is
+ * defined as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
+ * followed by a shift in of 18 bits. This first two bits shifted in
+ * are TurnAround bits used to avoid contention on the MDIO pin when a
+ * READ operation is performed. These two bits are thrown away
+ * followed by a shift in of 16 bits which contains the desired data.
+ */
+ mdic = ((reg_addr) | (phy_addr << 5) |
+ (PHY_OP_READ << 10) | (PHY_SOF << 12));
+
+ e1000_shift_out_mdi_bits(hw, mdic, 14);
+
+ /* Now that we've shifted out the read command to the MII, we need to
+ * "shift in" the 16-bit value (18 total bits) of the requested PHY
+ * register address.
+ */
+ *phy_data = e1000_shift_in_mdi_bits(hw);
+ }
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Initializes receive address filters.
- *
- * hw - Struct containing variables accessed by shared code
+/**
+ * e1000_write_phy_reg - write a phy register
*
- * Places the MAC address in receive address register 0 and clears the rest
- * of the receive addresss registers. Clears the multicast table. Assumes
- * the receiver is in reset when the routine is called.
- *****************************************************************************/
-static void e1000_init_rx_addrs(struct e1000_hw *hw)
+ * @hw: Struct containing variables accessed by shared code
+ * @reg_addr: address of the PHY register to write
+ * @data: data to write to the PHY
+
+ * Writes a value to a PHY register
+ */
+s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 phy_data)
{
- u32 i;
- u32 rar_num;
-
- DEBUGFUNC("e1000_init_rx_addrs");
-
- /* Setup the receive address. */
- DEBUGOUT("Programming MAC Address into RAR[0]\n");
-
- e1000_rar_set(hw, hw->mac_addr, 0);
-
- rar_num = E1000_RAR_ENTRIES;
-
- /* Reserve a spot for the Locally Administered Address to work around
- * an 82571 issue in which a reset on one port will reload the MAC on
- * the other port. */
- if ((hw->mac_type == e1000_82571) && (hw->laa_is_present))
- rar_num -= 1;
- if (hw->mac_type == e1000_ich8lan)
- rar_num = E1000_RAR_ENTRIES_ICH8LAN;
-
- /* Zero out the other 15 receive addresses. */
- DEBUGOUT("Clearing RAR[1-15]\n");
- for (i = 1; i < rar_num; i++) {
- E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
- E1000_WRITE_FLUSH();
- E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
- E1000_WRITE_FLUSH();
- }
+ u32 ret_val;
+
+ DEBUGFUNC("e1000_write_phy_reg");
+
+ if ((hw->phy_type == e1000_phy_igp) &&
+ (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
+ ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
+ (u16) reg_addr);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr,
+ phy_data);
+
+ return ret_val;
}
-/******************************************************************************
- * Hashes an address to determine its location in the multicast table
- *
- * hw - Struct containing variables accessed by shared code
- * mc_addr - the multicast address to hash
- *****************************************************************************/
-u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
+ u16 phy_data)
{
- u32 hash_value = 0;
-
- /* The portion of the address that is used for the hash table is
- * determined by the mc_filter_type setting.
- */
- switch (hw->mc_filter_type) {
- /* [0] [1] [2] [3] [4] [5]
- * 01 AA 00 12 34 56
- * LSB MSB
- */
- case 0:
- if (hw->mac_type == e1000_ich8lan) {
- /* [47:38] i.e. 0x158 for above example address */
- hash_value = ((mc_addr[4] >> 6) | (((u16)mc_addr[5]) << 2));
- } else {
- /* [47:36] i.e. 0x563 for above example address */
- hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
- }
- break;
- case 1:
- if (hw->mac_type == e1000_ich8lan) {
- /* [46:37] i.e. 0x2B1 for above example address */
- hash_value = ((mc_addr[4] >> 5) | (((u16)mc_addr[5]) << 3));
- } else {
- /* [46:35] i.e. 0xAC6 for above example address */
- hash_value = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5));
- }
- break;
- case 2:
- if (hw->mac_type == e1000_ich8lan) {
- /*[45:36] i.e. 0x163 for above example address */
- hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4));
- } else {
- /* [45:34] i.e. 0x5D8 for above example address */
- hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
- }
- break;
- case 3:
- if (hw->mac_type == e1000_ich8lan) {
- /* [43:34] i.e. 0x18D for above example address */
- hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6));
- } else {
- /* [43:32] i.e. 0x634 for above example address */
- hash_value = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8));
- }
- break;
- }
-
- hash_value &= 0xFFF;
- if (hw->mac_type == e1000_ich8lan)
- hash_value &= 0x3FF;
-
- return hash_value;
+ u32 i;
+ u32 mdic = 0;
+ const u32 phy_addr = 1;
+
+ DEBUGFUNC("e1000_write_phy_reg_ex");
+
+ if (reg_addr > MAX_PHY_REG_ADDRESS) {
+ DEBUGOUT1("PHY Address %d is out of range\n", reg_addr);
+ return -E1000_ERR_PARAM;
+ }
+
+ if (hw->mac_type > e1000_82543) {
+ /* Set up Op-code, Phy Address, register address, and data intended
+ * for the PHY register in the MDI Control register. The MAC will take
+ * care of interfacing with the PHY to send the desired data.
+ */
+ mdic = (((u32) phy_data) |
+ (reg_addr << E1000_MDIC_REG_SHIFT) |
+ (phy_addr << E1000_MDIC_PHY_SHIFT) |
+ (E1000_MDIC_OP_WRITE));
+
+ ew32(MDIC, mdic);
+
+ /* Poll the ready bit to see if the MDI read completed */
+ for (i = 0; i < 641; i++) {
+ udelay(5);
+ mdic = er32(MDIC);
+ if (mdic & E1000_MDIC_READY)
+ break;
+ }
+ if (!(mdic & E1000_MDIC_READY)) {
+ DEBUGOUT("MDI Write did not complete\n");
+ return -E1000_ERR_PHY;
+ }
+ } else {
+ /* We'll need to use the SW defined pins to shift the write command
+ * out to the PHY. We first send a preamble to the PHY to signal the
+ * beginning of the MII instruction. This is done by sending 32
+ * consecutive "1" bits.
+ */
+ e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
+
+ /* Now combine the remaining required fields that will indicate a
+ * write operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine for each field in the command. The
+ * format of a MII write instruction is as follows:
+ * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
+ */
+ mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
+ (PHY_OP_WRITE << 12) | (PHY_SOF << 14));
+ mdic <<= 16;
+ mdic |= (u32) phy_data;
+
+ e1000_shift_out_mdi_bits(hw, mdic, 32);
+ }
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Puts an ethernet address into a receive address register.
+/**
+ * e1000_phy_hw_reset - reset the phy, hardware style
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- * addr - Address to put into receive address register
- * index - Receive address register to write
- *****************************************************************************/
-void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+ * Returns the PHY to the power-on reset state
+ */
+s32 e1000_phy_hw_reset(struct e1000_hw *hw)
{
- u32 rar_low, rar_high;
-
- /* HW expects these in little endian so we reverse the byte order
- * from network order (big endian) to little endian
- */
- rar_low = ((u32)addr[0] | ((u32)addr[1] << 8) |
- ((u32)addr[2] << 16) | ((u32)addr[3] << 24));
- rar_high = ((u32)addr[4] | ((u32)addr[5] << 8));
-
- /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx
- * unit hang.
- *
- * Description:
- * If there are any Rx frames queued up or otherwise present in the HW
- * before RSS is enabled, and then we enable RSS, the HW Rx unit will
- * hang. To work around this issue, we have to disable receives and
- * flush out all Rx frames before we enable RSS. To do so, we modify we
- * redirect all Rx traffic to manageability and then reset the HW.
- * This flushes away Rx frames, and (since the redirections to
- * manageability persists across resets) keeps new ones from coming in
- * while we work. Then, we clear the Address Valid AV bit for all MAC
- * addresses and undo the re-direction to manageability.
- * Now, frames are coming in again, but the MAC won't accept them, so
- * far so good. We now proceed to initialize RSS (if necessary) and
- * configure the Rx unit. Last, we re-enable the AV bits and continue
- * on our merry way.
- */
- switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
- if (hw->leave_av_bit_off)
- break;
- default:
- /* Indicate to hardware the Address is Valid. */
- rar_high |= E1000_RAH_AV;
- break;
- }
-
- E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
- E1000_WRITE_FLUSH();
- E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
- E1000_WRITE_FLUSH();
+ u32 ctrl, ctrl_ext;
+ u32 led_ctrl;
+ s32 ret_val;
+
+ DEBUGFUNC("e1000_phy_hw_reset");
+
+ DEBUGOUT("Resetting Phy...\n");
+
+ if (hw->mac_type > e1000_82543) {
+ /* Read the device control register and assert the E1000_CTRL_PHY_RST
+ * bit. Then, take it out of reset.
+ * For e1000 hardware, we delay for 10ms between the assert
+ * and deassert.
+ */
+ ctrl = er32(CTRL);
+ ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
+ E1000_WRITE_FLUSH();
+
+ msleep(10);
+
+ ew32(CTRL, ctrl);
+ E1000_WRITE_FLUSH();
+
+ } else {
+ /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
+ * bit to put the PHY into reset. Then, take it out of reset.
+ */
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
+ ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ msleep(10);
+ ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA;
+ ew32(CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH();
+ }
+ udelay(150);
+
+ if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
+ /* Configure activity LED after PHY reset */
+ led_ctrl = er32(LEDCTL);
+ led_ctrl &= IGP_ACTIVITY_LED_MASK;
+ led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
+ ew32(LEDCTL, led_ctrl);
+ }
+
+ /* Wait for FW to finish PHY configuration. */
+ ret_val = e1000_get_phy_cfg_done(hw);
+ if (ret_val != E1000_SUCCESS)
+ return ret_val;
+
+ return ret_val;
}
-/******************************************************************************
- * Writes a value to the specified offset in the VLAN filter table.
+/**
+ * e1000_phy_reset - reset the phy to commit settings
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- * offset - Offset in VLAN filer table to write
- * value - Value to write into VLAN filter table
- *****************************************************************************/
-void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
+ * Resets the PHY
+ * Sets bit 15 of the MII Control register
+ */
+s32 e1000_phy_reset(struct e1000_hw *hw)
{
- u32 temp;
-
- if (hw->mac_type == e1000_ich8lan)
- return;
-
- if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
- temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
- E1000_WRITE_FLUSH();
- E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
- E1000_WRITE_FLUSH();
- } else {
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
- E1000_WRITE_FLUSH();
- }
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_phy_reset");
+
+ switch (hw->phy_type) {
+ case e1000_phy_igp:
+ ret_val = e1000_phy_hw_reset(hw);
+ if (ret_val)
+ return ret_val;
+ break;
+ default:
+ ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= MII_CR_RESET;
+ ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ udelay(1);
+ break;
+ }
+
+ if (hw->phy_type == e1000_phy_igp)
+ e1000_phy_init_script(hw);
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Clears the VLAN filer table
+/**
+ * e1000_detect_gig_phy - check the phy type
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static void e1000_clear_vfta(struct e1000_hw *hw)
+ * Probes the expected PHY address for known PHY IDs
+ */
+static s32 e1000_detect_gig_phy(struct e1000_hw *hw)
{
- u32 offset;
- u32 vfta_value = 0;
- u32 vfta_offset = 0;
- u32 vfta_bit_in_reg = 0;
-
- if (hw->mac_type == e1000_ich8lan)
- return;
-
- if (hw->mac_type == e1000_82573) {
- if (hw->mng_cookie.vlan_id != 0) {
- /* The VFTA is a 4096b bit-field, each identifying a single VLAN
- * ID. The following operations determine which 32b entry
- * (i.e. offset) into the array we want to set the VLAN ID
- * (i.e. bit) of the manageability unit. */
- vfta_offset = (hw->mng_cookie.vlan_id >>
- E1000_VFTA_ENTRY_SHIFT) &
- E1000_VFTA_ENTRY_MASK;
- vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id &
- E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
- }
- }
- for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
- /* If the offset we want to clear is the same offset of the
- * manageability VLAN ID, then clear all bits except that of the
- * manageability unit */
- vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
- E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
- E1000_WRITE_FLUSH();
- }
-}
+ s32 phy_init_status, ret_val;
+ u16 phy_id_high, phy_id_low;
+ bool match = false;
-static s32 e1000_id_led_init(struct e1000_hw *hw)
-{
- u32 ledctl;
- const u32 ledctl_mask = 0x000000FF;
- const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
- const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
- u16 eeprom_data, i, temp;
- const u16 led_mask = 0x0F;
-
- DEBUGFUNC("e1000_id_led_init");
-
- if (hw->mac_type < e1000_82540) {
- /* Nothing to do */
- return E1000_SUCCESS;
- }
-
- ledctl = er32(LEDCTL);
- hw->ledctl_default = ledctl;
- hw->ledctl_mode1 = hw->ledctl_default;
- hw->ledctl_mode2 = hw->ledctl_default;
-
- if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
- DEBUGOUT("EEPROM Read Error\n");
- return -E1000_ERR_EEPROM;
- }
-
- if ((hw->mac_type == e1000_82573) &&
- (eeprom_data == ID_LED_RESERVED_82573))
- eeprom_data = ID_LED_DEFAULT_82573;
- else if ((eeprom_data == ID_LED_RESERVED_0000) ||
- (eeprom_data == ID_LED_RESERVED_FFFF)) {
- if (hw->mac_type == e1000_ich8lan)
- eeprom_data = ID_LED_DEFAULT_ICH8LAN;
- else
- eeprom_data = ID_LED_DEFAULT;
- }
-
- for (i = 0; i < 4; i++) {
- temp = (eeprom_data >> (i << 2)) & led_mask;
- switch (temp) {
- case ID_LED_ON1_DEF2:
- case ID_LED_ON1_ON2:
- case ID_LED_ON1_OFF2:
- hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode1 |= ledctl_on << (i << 3);
- break;
- case ID_LED_OFF1_DEF2:
- case ID_LED_OFF1_ON2:
- case ID_LED_OFF1_OFF2:
- hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode1 |= ledctl_off << (i << 3);
- break;
- default:
- /* Do nothing */
- break;
- }
- switch (temp) {
- case ID_LED_DEF1_ON2:
- case ID_LED_ON1_ON2:
- case ID_LED_OFF1_ON2:
- hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode2 |= ledctl_on << (i << 3);
- break;
- case ID_LED_DEF1_OFF2:
- case ID_LED_ON1_OFF2:
- case ID_LED_OFF1_OFF2:
- hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
- hw->ledctl_mode2 |= ledctl_off << (i << 3);
- break;
- default:
- /* Do nothing */
- break;
- }
- }
- return E1000_SUCCESS;
+ DEBUGFUNC("e1000_detect_gig_phy");
+
+ if (hw->phy_id != 0)
+ return E1000_SUCCESS;
+
+ /* Read the PHY ID Registers to identify which PHY is onboard. */
+ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_id = (u32) (phy_id_high << 16);
+ udelay(20);
+ ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_id |= (u32) (phy_id_low & PHY_REVISION_MASK);
+ hw->phy_revision = (u32) phy_id_low & ~PHY_REVISION_MASK;
+
+ switch (hw->mac_type) {
+ case e1000_82543:
+ if (hw->phy_id == M88E1000_E_PHY_ID)
+ match = true;
+ break;
+ case e1000_82544:
+ if (hw->phy_id == M88E1000_I_PHY_ID)
+ match = true;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (hw->phy_id == M88E1011_I_PHY_ID)
+ match = true;
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (hw->phy_id == IGP01E1000_I_PHY_ID)
+ match = true;
+ break;
+ default:
+ DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type);
+ return -E1000_ERR_CONFIG;
+ }
+ phy_init_status = e1000_set_phy_type(hw);
+
+ if ((match) && (phy_init_status == E1000_SUCCESS)) {
+ DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id);
+ return E1000_SUCCESS;
+ }
+ DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id);
+ return -E1000_ERR_PHY;
}
-/******************************************************************************
- * Prepares SW controlable LED for use and saves the current state of the LED.
+/**
+ * e1000_phy_reset_dsp - reset DSP
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_setup_led(struct e1000_hw *hw)
+ * Resets the PHY's DSP
+ */
+static s32 e1000_phy_reset_dsp(struct e1000_hw *hw)
{
- u32 ledctl;
- s32 ret_val = E1000_SUCCESS;
-
- DEBUGFUNC("e1000_setup_led");
-
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- /* No setup necessary */
- break;
- case e1000_82541:
- case e1000_82547:
- case e1000_82541_rev_2:
- case e1000_82547_rev_2:
- /* Turn off PHY Smart Power Down (if enabled) */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
- &hw->phy_spd_default);
- if (ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
- (u16)(hw->phy_spd_default &
- ~IGP01E1000_GMII_SPD));
- if (ret_val)
- return ret_val;
- /* Fall Through */
- default:
- if (hw->media_type == e1000_media_type_fiber) {
- ledctl = er32(LEDCTL);
- /* Save current LEDCTL settings */
- hw->ledctl_default = ledctl;
- /* Turn off LED0 */
- ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
- E1000_LEDCTL_LED0_BLINK |
- E1000_LEDCTL_LED0_MODE_MASK);
- ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
- E1000_LEDCTL_LED0_MODE_SHIFT);
- ew32(LEDCTL, ledctl);
- } else if (hw->media_type == e1000_media_type_copper)
- ew32(LEDCTL, hw->ledctl_mode1);
- break;
- }
-
- return E1000_SUCCESS;
-}
+ s32 ret_val;
+ DEBUGFUNC("e1000_phy_reset_dsp");
+ do {
+ ret_val = e1000_write_phy_reg(hw, 29, 0x001d);
+ if (ret_val)
+ break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x00c1);
+ if (ret_val)
+ break;
+ ret_val = e1000_write_phy_reg(hw, 30, 0x0000);
+ if (ret_val)
+ break;
+ ret_val = E1000_SUCCESS;
+ } while (0);
-/******************************************************************************
- * Used on 82571 and later Si that has LED blink bits.
- * Callers must use their own timer and should have already called
- * e1000_id_led_init()
- * Call e1000_cleanup led() to stop blinking
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_blink_led_start(struct e1000_hw *hw)
-{
- s16 i;
- u32 ledctl_blink = 0;
-
- DEBUGFUNC("e1000_id_led_blink_on");
-
- if (hw->mac_type < e1000_82571) {
- /* Nothing to do */
- return E1000_SUCCESS;
- }
- if (hw->media_type == e1000_media_type_fiber) {
- /* always blink LED0 for PCI-E fiber */
- ledctl_blink = E1000_LEDCTL_LED0_BLINK |
- (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
- } else {
- /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */
- ledctl_blink = hw->ledctl_mode2;
- for (i=0; i < 4; i++)
- if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) ==
- E1000_LEDCTL_MODE_LED_ON)
- ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8));
- }
-
- ew32(LEDCTL, ledctl_blink);
-
- return E1000_SUCCESS;
+ return ret_val;
}
-/******************************************************************************
- * Restores the saved state of the SW controlable LED.
+/**
+ * e1000_phy_igp_get_info - get igp specific registers
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_cleanup_led(struct e1000_hw *hw)
+ * Get PHY information from various PHY registers for igp PHY only.
+ */
+static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
{
- s32 ret_val = E1000_SUCCESS;
-
- DEBUGFUNC("e1000_cleanup_led");
-
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- case e1000_82544:
- /* No cleanup necessary */
- break;
- case e1000_82541:
- case e1000_82547:
- case e1000_82541_rev_2:
- case e1000_82547_rev_2:
- /* Turn on PHY Smart Power Down (if previously enabled) */
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
- hw->phy_spd_default);
- if (ret_val)
- return ret_val;
- /* Fall Through */
- default:
- if (hw->phy_type == e1000_phy_ife) {
- e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0);
- break;
- }
- /* Restore LEDCTL settings */
- ew32(LEDCTL, hw->ledctl_default);
- break;
- }
-
- return E1000_SUCCESS;
+ s32 ret_val;
+ u16 phy_data, min_length, max_length, average;
+ e1000_rev_polarity polarity;
+
+ DEBUGFUNC("e1000_phy_igp_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
+
+ /* IGP01E1000 does not need to support it. */
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal;
+
+ /* IGP01E1000 always correct polarity reversal */
+ phy_info->polarity_correction = e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (e1000_auto_x_mode) ((phy_data & IGP01E1000_PSSR_MDIX) >>
+ IGP01E1000_PSSR_MDIX_SHIFT);
+
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+ /* Local/Remote Receiver Information are only valid at 1000 Mbps */
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+ phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+
+ /* Get cable length */
+ ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
+ if (ret_val)
+ return ret_val;
+
+ /* Translate to old method */
+ average = (max_length + min_length) / 2;
+
+ if (average <= e1000_igp_cable_length_50)
+ phy_info->cable_length = e1000_cable_length_50;
+ else if (average <= e1000_igp_cable_length_80)
+ phy_info->cable_length = e1000_cable_length_50_80;
+ else if (average <= e1000_igp_cable_length_110)
+ phy_info->cable_length = e1000_cable_length_80_110;
+ else if (average <= e1000_igp_cable_length_140)
+ phy_info->cable_length = e1000_cable_length_110_140;
+ else
+ phy_info->cable_length = e1000_cable_length_140;
+ }
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Turns on the software controllable LED
+/**
+ * e1000_phy_m88_get_info - get m88 specific registers
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_led_on(struct e1000_hw *hw)
+ * Get PHY information from various PHY registers for m88 PHY only.
+ */
+static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
+ struct e1000_phy_info *phy_info)
{
- u32 ctrl = er32(CTRL);
-
- DEBUGFUNC("e1000_led_on");
-
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- /* Set SW Defineable Pin 0 to turn on the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- break;
- case e1000_82544:
- if (hw->media_type == e1000_media_type_fiber) {
- /* Set SW Defineable Pin 0 to turn on the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- } else {
- /* Clear SW Defineable Pin 0 to turn on the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- }
- break;
- default:
- if (hw->media_type == e1000_media_type_fiber) {
- /* Clear SW Defineable Pin 0 to turn on the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- } else if (hw->phy_type == e1000_phy_ife) {
- e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
- (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON));
- } else if (hw->media_type == e1000_media_type_copper) {
- ew32(LEDCTL, hw->ledctl_mode2);
- return E1000_SUCCESS;
- }
- break;
- }
-
- ew32(CTRL, ctrl);
-
- return E1000_SUCCESS;
+ s32 ret_val;
+ u16 phy_data;
+ e1000_rev_polarity polarity;
+
+ DEBUGFUNC("e1000_phy_m88_get_info");
+
+ /* The downshift status is checked only once, after link is established,
+ * and it stored in the hw->speed_downgraded parameter. */
+ phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->extended_10bt_distance =
+ ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >>
+ M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ?
+ e1000_10bt_ext_dist_enable_lower :
+ e1000_10bt_ext_dist_enable_normal;
+
+ phy_info->polarity_correction =
+ ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >>
+ M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ?
+ e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled;
+
+ /* Check polarity status */
+ ret_val = e1000_check_polarity(hw, &polarity);
+ if (ret_val)
+ return ret_val;
+ phy_info->cable_polarity = polarity;
+
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->mdix_mode =
+ (e1000_auto_x_mode) ((phy_data & M88E1000_PSSR_MDIX) >>
+ M88E1000_PSSR_MDIX_SHIFT);
+
+ if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) {
+ /* Cable Length Estimation and Local/Remote Receiver Information
+ * are only valid at 1000 Mbps.
+ */
+ phy_info->cable_length =
+ (e1000_cable_length) ((phy_data &
+ M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT);
+
+ ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >>
+ SR_1000T_LOCAL_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+ phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >>
+ SR_1000T_REMOTE_RX_STATUS_SHIFT) ?
+ e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok;
+
+ }
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Turns off the software controllable LED
+/**
+ * e1000_phy_get_info - request phy info
+ * @hw: Struct containing variables accessed by shared code
+ * @phy_info: PHY information structure
*
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-s32 e1000_led_off(struct e1000_hw *hw)
+ * Get PHY information from various PHY registers
+ */
+s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info)
{
- u32 ctrl = er32(CTRL);
-
- DEBUGFUNC("e1000_led_off");
-
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- case e1000_82543:
- /* Clear SW Defineable Pin 0 to turn off the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- break;
- case e1000_82544:
- if (hw->media_type == e1000_media_type_fiber) {
- /* Clear SW Defineable Pin 0 to turn off the LED */
- ctrl &= ~E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- } else {
- /* Set SW Defineable Pin 0 to turn off the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- }
- break;
- default:
- if (hw->media_type == e1000_media_type_fiber) {
- /* Set SW Defineable Pin 0 to turn off the LED */
- ctrl |= E1000_CTRL_SWDPIN0;
- ctrl |= E1000_CTRL_SWDPIO0;
- } else if (hw->phy_type == e1000_phy_ife) {
- e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED,
- (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF));
- } else if (hw->media_type == e1000_media_type_copper) {
- ew32(LEDCTL, hw->ledctl_mode1);
- return E1000_SUCCESS;
- }
- break;
- }
-
- ew32(CTRL, ctrl);
-
- return E1000_SUCCESS;
-}
+ s32 ret_val;
+ u16 phy_data;
-/******************************************************************************
- * Clears all hardware statistics counters.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static void e1000_clear_hw_cntrs(struct e1000_hw *hw)
+ DEBUGFUNC("e1000_phy_get_info");
+
+ phy_info->cable_length = e1000_cable_length_undefined;
+ phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined;
+ phy_info->cable_polarity = e1000_rev_polarity_undefined;
+ phy_info->downshift = e1000_downshift_undefined;
+ phy_info->polarity_correction = e1000_polarity_reversal_undefined;
+ phy_info->mdix_mode = e1000_auto_x_mode_undefined;
+ phy_info->local_rx = e1000_1000t_rx_status_undefined;
+ phy_info->remote_rx = e1000_1000t_rx_status_undefined;
+
+ if (hw->media_type != e1000_media_type_copper) {
+ DEBUGOUT("PHY info is only valid for copper media\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) {
+ DEBUGOUT("PHY info is only valid if link is up\n");
+ return -E1000_ERR_CONFIG;
+ }
+
+ if (hw->phy_type == e1000_phy_igp)
+ return e1000_phy_igp_get_info(hw, phy_info);
+ else
+ return e1000_phy_m88_get_info(hw, phy_info);
+}
+
+s32 e1000_validate_mdi_setting(struct e1000_hw *hw)
{
- volatile u32 temp;
-
- temp = er32(CRCERRS);
- temp = er32(SYMERRS);
- temp = er32(MPC);
- temp = er32(SCC);
- temp = er32(ECOL);
- temp = er32(MCC);
- temp = er32(LATECOL);
- temp = er32(COLC);
- temp = er32(DC);
- temp = er32(SEC);
- temp = er32(RLEC);
- temp = er32(XONRXC);
- temp = er32(XONTXC);
- temp = er32(XOFFRXC);
- temp = er32(XOFFTXC);
- temp = er32(FCRUC);
-
- if (hw->mac_type != e1000_ich8lan) {
- temp = er32(PRC64);
- temp = er32(PRC127);
- temp = er32(PRC255);
- temp = er32(PRC511);
- temp = er32(PRC1023);
- temp = er32(PRC1522);
- }
-
- temp = er32(GPRC);
- temp = er32(BPRC);
- temp = er32(MPRC);
- temp = er32(GPTC);
- temp = er32(GORCL);
- temp = er32(GORCH);
- temp = er32(GOTCL);
- temp = er32(GOTCH);
- temp = er32(RNBC);
- temp = er32(RUC);
- temp = er32(RFC);
- temp = er32(ROC);
- temp = er32(RJC);
- temp = er32(TORL);
- temp = er32(TORH);
- temp = er32(TOTL);
- temp = er32(TOTH);
- temp = er32(TPR);
- temp = er32(TPT);
-
- if (hw->mac_type != e1000_ich8lan) {
- temp = er32(PTC64);
- temp = er32(PTC127);
- temp = er32(PTC255);
- temp = er32(PTC511);
- temp = er32(PTC1023);
- temp = er32(PTC1522);
- }
-
- temp = er32(MPTC);
- temp = er32(BPTC);
-
- if (hw->mac_type < e1000_82543) return;
-
- temp = er32(ALGNERRC);
- temp = er32(RXERRC);
- temp = er32(TNCRS);
- temp = er32(CEXTERR);
- temp = er32(TSCTC);
- temp = er32(TSCTFC);
-
- if (hw->mac_type <= e1000_82544) return;
-
- temp = er32(MGTPRC);
- temp = er32(MGTPDC);
- temp = er32(MGTPTC);
-
- if (hw->mac_type <= e1000_82547_rev_2) return;
-
- temp = er32(IAC);
- temp = er32(ICRXOC);
-
- if (hw->mac_type == e1000_ich8lan) return;
-
- temp = er32(ICRXPTC);
- temp = er32(ICRXATC);
- temp = er32(ICTXPTC);
- temp = er32(ICTXATC);
- temp = er32(ICTXQEC);
- temp = er32(ICTXQMTC);
- temp = er32(ICRXDMTC);
+ DEBUGFUNC("e1000_validate_mdi_settings");
+
+ if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) {
+ DEBUGOUT("Invalid MDI setting detected\n");
+ hw->mdix = 1;
+ return -E1000_ERR_CONFIG;
+ }
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Resets Adaptive IFS to its default state.
+/**
+ * e1000_init_eeprom_params - initialize sw eeprom vars
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- *
- * Call this after e1000_init_hw. You may override the IFS defaults by setting
- * hw->ifs_params_forced to true. However, you must initialize hw->
- * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
- * before calling this function.
- *****************************************************************************/
-void e1000_reset_adaptive(struct e1000_hw *hw)
+ * Sets up eeprom variables in the hw struct. Must be called after mac_type
+ * is configured.
+ */
+s32 e1000_init_eeprom_params(struct e1000_hw *hw)
{
- DEBUGFUNC("e1000_reset_adaptive");
-
- if (hw->adaptive_ifs) {
- if (!hw->ifs_params_forced) {
- hw->current_ifs_val = 0;
- hw->ifs_min_val = IFS_MIN;
- hw->ifs_max_val = IFS_MAX;
- hw->ifs_step_size = IFS_STEP;
- hw->ifs_ratio = IFS_RATIO;
- }
- hw->in_ifs_mode = false;
- ew32(AIT, 0);
- } else {
- DEBUGOUT("Not in Adaptive IFS mode!\n");
- }
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd = er32(EECD);
+ s32 ret_val = E1000_SUCCESS;
+ u16 eeprom_size;
+
+ DEBUGFUNC("e1000_init_eeprom_params");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->word_size = 64;
+ eeprom->opcode_bits = 3;
+ eeprom->address_bits = 6;
+ eeprom->delay_usec = 50;
+ break;
+ case e1000_82540:
+ case e1000_82545:
+ case e1000_82545_rev_3:
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_SIZE) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ break;
+ case e1000_82541:
+ case e1000_82541_rev_2:
+ case e1000_82547:
+ case e1000_82547_rev_2:
+ if (eecd & E1000_EECD_TYPE) {
+ eeprom->type = e1000_eeprom_spi;
+ eeprom->opcode_bits = 8;
+ eeprom->delay_usec = 1;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->page_size = 32;
+ eeprom->address_bits = 16;
+ } else {
+ eeprom->page_size = 8;
+ eeprom->address_bits = 8;
+ }
+ } else {
+ eeprom->type = e1000_eeprom_microwire;
+ eeprom->opcode_bits = 3;
+ eeprom->delay_usec = 50;
+ if (eecd & E1000_EECD_ADDR_BITS) {
+ eeprom->word_size = 256;
+ eeprom->address_bits = 8;
+ } else {
+ eeprom->word_size = 64;
+ eeprom->address_bits = 6;
+ }
+ }
+ break;
+ default:
+ break;
+ }
+
+ if (eeprom->type == e1000_eeprom_spi) {
+ /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
+ * 32KB (incremented by powers of 2).
+ */
+ /* Set to default value for initial eeprom read. */
+ eeprom->word_size = 64;
+ ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size);
+ if (ret_val)
+ return ret_val;
+ eeprom_size =
+ (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
+ /* 256B eeprom size was not supported in earlier hardware, so we
+ * bump eeprom_size up one to ensure that "1" (which maps to 256B)
+ * is never the result used in the shifting logic below. */
+ if (eeprom_size)
+ eeprom_size++;
+
+ eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
+ }
+ return ret_val;
}
-/******************************************************************************
- * Called during the callback/watchdog routine to update IFS value based on
- * the ratio of transmits to collisions.
- *
- * hw - Struct containing variables accessed by shared code
- * tx_packets - Number of transmits since last callback
- * total_collisions - Number of collisions since last callback
- *****************************************************************************/
-void e1000_update_adaptive(struct e1000_hw *hw)
+/**
+ * e1000_raise_ee_clk - Raises the EEPROM's clock input.
+ * @hw: Struct containing variables accessed by shared code
+ * @eecd: EECD's current value
+ */
+static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd)
{
- DEBUGFUNC("e1000_update_adaptive");
-
- if (hw->adaptive_ifs) {
- if ((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) {
- if (hw->tx_packet_delta > MIN_NUM_XMITS) {
- hw->in_ifs_mode = true;
- if (hw->current_ifs_val < hw->ifs_max_val) {
- if (hw->current_ifs_val == 0)
- hw->current_ifs_val = hw->ifs_min_val;
- else
- hw->current_ifs_val += hw->ifs_step_size;
- ew32(AIT, hw->current_ifs_val);
- }
- }
- } else {
- if (hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
- hw->current_ifs_val = 0;
- hw->in_ifs_mode = false;
- ew32(AIT, 0);
- }
- }
- } else {
- DEBUGOUT("Not in Adaptive IFS mode!\n");
- }
+ /* Raise the clock input to the EEPROM (by setting the SK bit), and then
+ * wait <delay> microseconds.
+ */
+ *eecd = *eecd | E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
}
-/******************************************************************************
- * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
- *
- * hw - Struct containing variables accessed by shared code
- * frame_len - The length of the frame in question
- * mac_addr - The Ethernet destination address of the frame in question
- *****************************************************************************/
-void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
- u32 frame_len, u8 *mac_addr)
+/**
+ * e1000_lower_ee_clk - Lowers the EEPROM's clock input.
+ * @hw: Struct containing variables accessed by shared code
+ * @eecd: EECD's current value
+ */
+static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd)
{
- u64 carry_bit;
-
- /* First adjust the frame length. */
- frame_len--;
- /* We need to adjust the statistics counters, since the hardware
- * counters overcount this packet as a CRC error and undercount
- * the packet as a good packet
- */
- /* This packet should not be counted as a CRC error. */
- stats->crcerrs--;
- /* This packet does count as a Good Packet Received. */
- stats->gprc++;
-
- /* Adjust the Good Octets received counters */
- carry_bit = 0x80000000 & stats->gorcl;
- stats->gorcl += frame_len;
- /* If the high bit of Gorcl (the low 32 bits of the Good Octets
- * Received Count) was one before the addition,
- * AND it is zero after, then we lost the carry out,
- * need to add one to Gorch (Good Octets Received Count High).
- * This could be simplified if all environments supported
- * 64-bit integers.
- */
- if (carry_bit && ((stats->gorcl & 0x80000000) == 0))
- stats->gorch++;
- /* Is this a broadcast or multicast? Check broadcast first,
- * since the test for a multicast frame will test positive on
- * a broadcast frame.
- */
- if ((mac_addr[0] == (u8)0xff) && (mac_addr[1] == (u8)0xff))
- /* Broadcast packet */
- stats->bprc++;
- else if (*mac_addr & 0x01)
- /* Multicast packet */
- stats->mprc++;
-
- if (frame_len == hw->max_frame_size) {
- /* In this case, the hardware has overcounted the number of
- * oversize frames.
- */
- if (stats->roc > 0)
- stats->roc--;
- }
-
- /* Adjust the bin counters when the extra byte put the frame in the
- * wrong bin. Remember that the frame_len was adjusted above.
- */
- if (frame_len == 64) {
- stats->prc64++;
- stats->prc127--;
- } else if (frame_len == 127) {
- stats->prc127++;
- stats->prc255--;
- } else if (frame_len == 255) {
- stats->prc255++;
- stats->prc511--;
- } else if (frame_len == 511) {
- stats->prc511++;
- stats->prc1023--;
- } else if (frame_len == 1023) {
- stats->prc1023++;
- stats->prc1522--;
- } else if (frame_len == 1522) {
- stats->prc1522++;
- }
+ /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
+ * wait 50 microseconds.
+ */
+ *eecd = *eecd & ~E1000_EECD_SK;
+ ew32(EECD, *eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
}
-/******************************************************************************
- * Gets the current PCI bus type, speed, and width of the hardware
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-void e1000_get_bus_info(struct e1000_hw *hw)
+/**
+ * e1000_shift_out_ee_bits - Shift data bits out to the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @data: data to send to the EEPROM
+ * @count: number of bits to shift out
+ */
+static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count)
{
- s32 ret_val;
- u16 pci_ex_link_status;
- u32 status;
-
- switch (hw->mac_type) {
- case e1000_82542_rev2_0:
- case e1000_82542_rev2_1:
- hw->bus_type = e1000_bus_type_pci;
- hw->bus_speed = e1000_bus_speed_unknown;
- hw->bus_width = e1000_bus_width_unknown;
- break;
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- hw->bus_type = e1000_bus_type_pci_express;
- hw->bus_speed = e1000_bus_speed_2500;
- ret_val = e1000_read_pcie_cap_reg(hw,
- PCI_EX_LINK_STATUS,
- &pci_ex_link_status);
- if (ret_val)
- hw->bus_width = e1000_bus_width_unknown;
- else
- hw->bus_width = (pci_ex_link_status & PCI_EX_LINK_WIDTH_MASK) >>
- PCI_EX_LINK_WIDTH_SHIFT;
- break;
- case e1000_ich8lan:
- hw->bus_type = e1000_bus_type_pci_express;
- hw->bus_speed = e1000_bus_speed_2500;
- hw->bus_width = e1000_bus_width_pciex_1;
- break;
- default:
- status = er32(STATUS);
- hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
- e1000_bus_type_pcix : e1000_bus_type_pci;
-
- if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
- hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
- e1000_bus_speed_66 : e1000_bus_speed_120;
- } else if (hw->bus_type == e1000_bus_type_pci) {
- hw->bus_speed = (status & E1000_STATUS_PCI66) ?
- e1000_bus_speed_66 : e1000_bus_speed_33;
- } else {
- switch (status & E1000_STATUS_PCIX_SPEED) {
- case E1000_STATUS_PCIX_SPEED_66:
- hw->bus_speed = e1000_bus_speed_66;
- break;
- case E1000_STATUS_PCIX_SPEED_100:
- hw->bus_speed = e1000_bus_speed_100;
- break;
- case E1000_STATUS_PCIX_SPEED_133:
- hw->bus_speed = e1000_bus_speed_133;
- break;
- default:
- hw->bus_speed = e1000_bus_speed_reserved;
- break;
- }
- }
- hw->bus_width = (status & E1000_STATUS_BUS64) ?
- e1000_bus_width_64 : e1000_bus_width_32;
- break;
- }
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+ u32 mask;
+
+ /* We need to shift "count" bits out to the EEPROM. So, value in the
+ * "data" parameter will be shifted out to the EEPROM one bit at a time.
+ * In order to do this, "data" must be broken down into bits.
+ */
+ mask = 0x01 << (count - 1);
+ eecd = er32(EECD);
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~E1000_EECD_DO;
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_DO;
+ }
+ do {
+ /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
+ * and then raising and then lowering the clock (the SK bit controls
+ * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
+ * by setting "DI" to "0" and then raising and then lowering the clock.
+ */
+ eecd &= ~E1000_EECD_DI;
+
+ if (data & mask)
+ eecd |= E1000_EECD_DI;
+
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+
+ udelay(eeprom->delay_usec);
+
+ e1000_raise_ee_clk(hw, &eecd);
+ e1000_lower_ee_clk(hw, &eecd);
+
+ mask = mask >> 1;
+
+ } while (mask);
+
+ /* We leave the "DI" bit set to "0" when we leave this routine. */
+ eecd &= ~E1000_EECD_DI;
+ ew32(EECD, eecd);
}
-/******************************************************************************
- * Writes a value to one of the devices registers using port I/O (as opposed to
- * memory mapped I/O). Only 82544 and newer devices support port I/O.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset to write to
- * value - value to write
- *****************************************************************************/
-static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value)
+/**
+ * e1000_shift_in_ee_bits - Shift data bits in from the EEPROM
+ * @hw: Struct containing variables accessed by shared code
+ * @count: number of bits to shift in
+ */
+static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count)
{
- unsigned long io_addr = hw->io_base;
- unsigned long io_data = hw->io_base + 4;
+ u32 eecd;
+ u32 i;
+ u16 data;
+
+ /* In order to read a register from the EEPROM, we need to shift 'count'
+ * bits in from the EEPROM. Bits are "shifted in" by raising the clock
+ * input to the EEPROM (setting the SK bit), and then reading the value of
+ * the "DO" bit. During this "shifting in" process the "DI" bit should
+ * always be clear.
+ */
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
+ data = 0;
- e1000_io_write(hw, io_addr, offset);
- e1000_io_write(hw, io_data, value);
+ for (i = 0; i < count; i++) {
+ data = data << 1;
+ e1000_raise_ee_clk(hw, &eecd);
+
+ eecd = er32(EECD);
+
+ eecd &= ~(E1000_EECD_DI);
+ if (eecd & E1000_EECD_DO)
+ data |= 1;
+
+ e1000_lower_ee_clk(hw, &eecd);
+ }
+
+ return data;
}
-/******************************************************************************
- * Estimates the cable length.
- *
- * hw - Struct containing variables accessed by shared code
- * min_length - The estimated minimum length
- * max_length - The estimated maximum length
- *
- * returns: - E1000_ERR_XXX
- * E1000_SUCCESS
+/**
+ * e1000_acquire_eeprom - Prepares EEPROM for access
+ * @hw: Struct containing variables accessed by shared code
*
- * This function always returns a ranged length (minimum & maximum).
- * So for M88 phy's, this function interprets the one value returned from the
- * register to the minimum and maximum range.
- * For IGP phy's, the function calculates the range by the AGC registers.
- *****************************************************************************/
-static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
- u16 *max_length)
+ * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
+ * function should be called before issuing a command to the EEPROM.
+ */
+static s32 e1000_acquire_eeprom(struct e1000_hw *hw)
{
- s32 ret_val;
- u16 agc_value = 0;
- u16 i, phy_data;
- u16 cable_length;
-
- DEBUGFUNC("e1000_get_cable_length");
-
- *min_length = *max_length = 0;
-
- /* Use old method for Phy older than IGP */
- if (hw->phy_type == e1000_phy_m88) {
-
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
- if (ret_val)
- return ret_val;
- cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
- M88E1000_PSSR_CABLE_LENGTH_SHIFT;
-
- /* Convert the enum value to ranged values */
- switch (cable_length) {
- case e1000_cable_length_50:
- *min_length = 0;
- *max_length = e1000_igp_cable_length_50;
- break;
- case e1000_cable_length_50_80:
- *min_length = e1000_igp_cable_length_50;
- *max_length = e1000_igp_cable_length_80;
- break;
- case e1000_cable_length_80_110:
- *min_length = e1000_igp_cable_length_80;
- *max_length = e1000_igp_cable_length_110;
- break;
- case e1000_cable_length_110_140:
- *min_length = e1000_igp_cable_length_110;
- *max_length = e1000_igp_cable_length_140;
- break;
- case e1000_cable_length_140:
- *min_length = e1000_igp_cable_length_140;
- *max_length = e1000_igp_cable_length_170;
- break;
- default:
- return -E1000_ERR_PHY;
- break;
- }
- } else if (hw->phy_type == e1000_phy_gg82563) {
- ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE,
- &phy_data);
- if (ret_val)
- return ret_val;
- cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH;
-
- switch (cable_length) {
- case e1000_gg_cable_length_60:
- *min_length = 0;
- *max_length = e1000_igp_cable_length_60;
- break;
- case e1000_gg_cable_length_60_115:
- *min_length = e1000_igp_cable_length_60;
- *max_length = e1000_igp_cable_length_115;
- break;
- case e1000_gg_cable_length_115_150:
- *min_length = e1000_igp_cable_length_115;
- *max_length = e1000_igp_cable_length_150;
- break;
- case e1000_gg_cable_length_150:
- *min_length = e1000_igp_cable_length_150;
- *max_length = e1000_igp_cable_length_180;
- break;
- default:
- return -E1000_ERR_PHY;
- break;
- }
- } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
- u16 cur_agc_value;
- u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
- u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
- {IGP01E1000_PHY_AGC_A,
- IGP01E1000_PHY_AGC_B,
- IGP01E1000_PHY_AGC_C,
- IGP01E1000_PHY_AGC_D};
- /* Read the AGC registers for all channels */
- for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
-
- ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
- if (ret_val)
- return ret_val;
-
- cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
-
- /* Value bound check. */
- if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) ||
- (cur_agc_value == 0))
- return -E1000_ERR_PHY;
-
- agc_value += cur_agc_value;
-
- /* Update minimal AGC value. */
- if (min_agc_value > cur_agc_value)
- min_agc_value = cur_agc_value;
- }
-
- /* Remove the minimal AGC result for length < 50m */
- if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
- agc_value -= min_agc_value;
-
- /* Get the average length of the remaining 3 channels */
- agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
- } else {
- /* Get the average length of all the 4 channels. */
- agc_value /= IGP01E1000_PHY_CHANNEL_NUM;
- }
-
- /* Set the range of the calculated length. */
- *min_length = ((e1000_igp_cable_length_table[agc_value] -
- IGP01E1000_AGC_RANGE) > 0) ?
- (e1000_igp_cable_length_table[agc_value] -
- IGP01E1000_AGC_RANGE) : 0;
- *max_length = e1000_igp_cable_length_table[agc_value] +
- IGP01E1000_AGC_RANGE;
- } else if (hw->phy_type == e1000_phy_igp_2 ||
- hw->phy_type == e1000_phy_igp_3) {
- u16 cur_agc_index, max_agc_index = 0;
- u16 min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1;
- u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] =
- {IGP02E1000_PHY_AGC_A,
- IGP02E1000_PHY_AGC_B,
- IGP02E1000_PHY_AGC_C,
- IGP02E1000_PHY_AGC_D};
- /* Read the AGC registers for all channels */
- for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
- if (ret_val)
- return ret_val;
-
- /* Getting bits 15:9, which represent the combination of course and
- * fine gain values. The result is a number that can be put into
- * the lookup table to obtain the approximate cable length. */
- cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) &
- IGP02E1000_AGC_LENGTH_MASK;
-
- /* Array index bound check. */
- if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) ||
- (cur_agc_index == 0))
- return -E1000_ERR_PHY;
-
- /* Remove min & max AGC values from calculation. */
- if (e1000_igp_2_cable_length_table[min_agc_index] >
- e1000_igp_2_cable_length_table[cur_agc_index])
- min_agc_index = cur_agc_index;
- if (e1000_igp_2_cable_length_table[max_agc_index] <
- e1000_igp_2_cable_length_table[cur_agc_index])
- max_agc_index = cur_agc_index;
-
- agc_value += e1000_igp_2_cable_length_table[cur_agc_index];
- }
-
- agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] +
- e1000_igp_2_cable_length_table[max_agc_index]);
- agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2);
-
- /* Calculate cable length with the error range of +/- 10 meters. */
- *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ?
- (agc_value - IGP02E1000_AGC_RANGE) : 0;
- *max_length = agc_value + IGP02E1000_AGC_RANGE;
- }
-
- return E1000_SUCCESS;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd, i = 0;
+
+ DEBUGFUNC("e1000_acquire_eeprom");
+
+ eecd = er32(EECD);
+
+ /* Request EEPROM Access */
+ if (hw->mac_type > e1000_82544) {
+ eecd |= E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ eecd = er32(EECD);
+ while ((!(eecd & E1000_EECD_GNT)) &&
+ (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
+ i++;
+ udelay(5);
+ eecd = er32(EECD);
+ }
+ if (!(eecd & E1000_EECD_GNT)) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ DEBUGOUT("Could not acquire EEPROM grant\n");
+ return -E1000_ERR_EEPROM;
+ }
+ }
+
+ /* Setup EEPROM for Read/Write */
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ /* Clear SK and DI */
+ eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
+ ew32(EECD, eecd);
+
+ /* Set CS */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Clear SK and CS */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ udelay(1);
+ }
+
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Check the cable polarity
- *
- * hw - Struct containing variables accessed by shared code
- * polarity - output parameter : 0 - Polarity is not reversed
- * 1 - Polarity is reversed.
- *
- * returns: - E1000_ERR_XXX
- * E1000_SUCCESS
- *
- * For phy's older than IGP, this function simply reads the polarity bit in the
- * Phy Status register. For IGP phy's, this bit is valid only if link speed is
- * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will
- * return 0. If the link speed is 1000 Mbps the polarity status is in the
- * IGP01E1000_PHY_PCS_INIT_REG.
- *****************************************************************************/
-static s32 e1000_check_polarity(struct e1000_hw *hw,
- e1000_rev_polarity *polarity)
+/**
+ * e1000_standby_eeprom - Returns EEPROM to a "standby" state
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_standby_eeprom(struct e1000_hw *hw)
{
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_check_polarity");
-
- if ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563)) {
- /* return the Polarity bit in the Status register. */
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
- if (ret_val)
- return ret_val;
- *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >>
- M88E1000_PSSR_REV_POLARITY_SHIFT) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
-
- } else if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) {
- /* Read the Status register to check the speed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
- * find the polarity status */
- if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
- IGP01E1000_PSSR_SPEED_1000MBPS) {
-
- /* Read the GIG initialization PCS register (0x00B4) */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- /* Check the polarity bits */
- *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
- } else {
- /* For 10 Mbps, read the polarity bit in the status register. (for
- * 100 Mbps this bit is always 0) */
- *polarity = (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
- }
- } else if (hw->phy_type == e1000_phy_ife) {
- ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL,
- &phy_data);
- if (ret_val)
- return ret_val;
- *polarity = ((phy_data & IFE_PESC_POLARITY_REVERSED) >>
- IFE_PESC_POLARITY_REVERSED_SHIFT) ?
- e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
- }
- return E1000_SUCCESS;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+
+ eecd = er32(EECD);
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Clock high */
+ eecd |= E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Select EEPROM */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+
+ /* Clock low */
+ eecd &= ~E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ } else if (eeprom->type == e1000_eeprom_spi) {
+ /* Toggle CS to flush commands */
+ eecd |= E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ eecd &= ~E1000_EECD_CS;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(eeprom->delay_usec);
+ }
}
-/******************************************************************************
- * Check if Downshift occured
+/**
+ * e1000_release_eeprom - drop chip select
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - Struct containing variables accessed by shared code
- * downshift - output parameter : 0 - No Downshift ocured.
- * 1 - Downshift ocured.
- *
- * returns: - E1000_ERR_XXX
- * E1000_SUCCESS
- *
- * For phy's older than IGP, this function reads the Downshift bit in the Phy
- * Specific Status register. For IGP phy's, it reads the Downgrade bit in the
- * Link Health register. In IGP this bit is latched high, so the driver must
- * read it immediately after link is established.
- *****************************************************************************/
-static s32 e1000_check_downshift(struct e1000_hw *hw)
+ * Terminates a command by inverting the EEPROM's chip select pin
+ */
+static void e1000_release_eeprom(struct e1000_hw *hw)
{
- s32 ret_val;
- u16 phy_data;
-
- DEBUGFUNC("e1000_check_downshift");
-
- if (hw->phy_type == e1000_phy_igp ||
- hw->phy_type == e1000_phy_igp_3 ||
- hw->phy_type == e1000_phy_igp_2) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
- } else if ((hw->phy_type == e1000_phy_m88) ||
- (hw->phy_type == e1000_phy_gg82563)) {
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
- M88E1000_PSSR_DOWNSHIFT_SHIFT;
- } else if (hw->phy_type == e1000_phy_ife) {
- /* e1000_phy_ife supports 10/100 speed only */
- hw->speed_downgraded = false;
- }
-
- return E1000_SUCCESS;
+ u32 eecd;
+
+ DEBUGFUNC("e1000_release_eeprom");
+
+ eecd = er32(EECD);
+
+ if (hw->eeprom.type == e1000_eeprom_spi) {
+ eecd |= E1000_EECD_CS; /* Pull CS high */
+ eecd &= ~E1000_EECD_SK; /* Lower SCK */
+
+ ew32(EECD, eecd);
+
+ udelay(hw->eeprom.delay_usec);
+ } else if (hw->eeprom.type == e1000_eeprom_microwire) {
+ /* cleanup eeprom */
+
+ /* CS on Microwire is active-high */
+ eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);
+
+ ew32(EECD, eecd);
+
+ /* Rising edge of clock */
+ eecd |= E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+
+ /* Falling edge of clock */
+ eecd &= ~E1000_EECD_SK;
+ ew32(EECD, eecd);
+ E1000_WRITE_FLUSH();
+ udelay(hw->eeprom.delay_usec);
+ }
+
+ /* Stop requesting EEPROM access */
+ if (hw->mac_type > e1000_82544) {
+ eecd &= ~E1000_EECD_REQ;
+ ew32(EECD, eecd);
+ }
}
-/*****************************************************************************
- *
- * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a
- * gigabit link is achieved to improve link quality.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_PHY if fail to read/write the PHY
- * E1000_SUCCESS at any other case.
- *
- ****************************************************************************/
+/**
+ * e1000_spi_eeprom_ready - Reads a 16 bit word from the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw)
+{
+ u16 retry_count = 0;
+ u8 spi_stat_reg;
-static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
+ DEBUGFUNC("e1000_spi_eeprom_ready");
+
+ /* Read "Status Register" repeatedly until the LSB is cleared. The
+ * EEPROM will signal that the command has been completed by clearing
+ * bit 0 of the internal status register. If it's not cleared within
+ * 5 milliseconds, then error out.
+ */
+ retry_count = 0;
+ do {
+ e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
+ hw->eeprom.opcode_bits);
+ spi_stat_reg = (u8) e1000_shift_in_ee_bits(hw, 8);
+ if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
+ break;
+
+ udelay(5);
+ retry_count += 5;
+
+ e1000_standby_eeprom(hw);
+ } while (retry_count < EEPROM_MAX_RETRY_SPI);
+
+ /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
+ * only 0-5mSec on 5V devices)
+ */
+ if (retry_count >= EEPROM_MAX_RETRY_SPI) {
+ DEBUGOUT("SPI EEPROM Status error\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_read_eeprom - Reads a 16 bit word from the EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset of word in the EEPROM to read
+ * @data: word read from the EEPROM
+ * @words: number of words to read
+ */
+s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
{
- s32 ret_val;
- u16 phy_data, phy_saved_data, speed, duplex, i;
- u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
- {IGP01E1000_PHY_AGC_PARAM_A,
- IGP01E1000_PHY_AGC_PARAM_B,
- IGP01E1000_PHY_AGC_PARAM_C,
- IGP01E1000_PHY_AGC_PARAM_D};
- u16 min_length, max_length;
-
- DEBUGFUNC("e1000_config_dsp_after_link_change");
-
- if (hw->phy_type != e1000_phy_igp)
- return E1000_SUCCESS;
-
- if (link_up) {
- ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
- if (ret_val) {
- DEBUGOUT("Error getting link speed and duplex\n");
- return ret_val;
- }
-
- if (speed == SPEED_1000) {
-
- ret_val = e1000_get_cable_length(hw, &min_length, &max_length);
- if (ret_val)
- return ret_val;
-
- if ((hw->dsp_config_state == e1000_dsp_config_enabled) &&
- min_length >= e1000_igp_cable_length_50) {
-
- for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i],
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
-
- ret_val = e1000_write_phy_reg(hw, dsp_reg_array[i],
- phy_data);
- if (ret_val)
- return ret_val;
- }
- hw->dsp_config_state = e1000_dsp_config_activated;
- }
-
- if ((hw->ffe_config_state == e1000_ffe_config_enabled) &&
- (min_length < e1000_igp_cable_length_50)) {
-
- u16 ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20;
- u32 idle_errs = 0;
-
- /* clear previous idle error counts */
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- for (i = 0; i < ffe_idle_err_timeout; i++) {
- udelay(1000);
- ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT);
- if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) {
- hw->ffe_config_state = e1000_ffe_config_active;
-
- ret_val = e1000_write_phy_reg(hw,
- IGP01E1000_PHY_DSP_FFE,
- IGP01E1000_PHY_DSP_FFE_CM_CP);
- if (ret_val)
- return ret_val;
- break;
- }
-
- if (idle_errs)
- ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100;
- }
- }
- }
- } else {
- if (hw->dsp_config_state == e1000_dsp_config_activated) {
- /* Save off the current value of register 0x2F5B to be restored at
- * the end of the routines. */
- ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
-
- if (ret_val)
- return ret_val;
-
- /* Disable the PHY transmitter */
- ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
-
- if (ret_val)
- return ret_val;
-
- mdelay(20);
-
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_FORCE_GIGA);
- if (ret_val)
- return ret_val;
- for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
- ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
- phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
-
- ret_val = e1000_write_phy_reg(hw,dsp_reg_array[i], phy_data);
- if (ret_val)
- return ret_val;
- }
-
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_RESTART_AUTONEG);
- if (ret_val)
- return ret_val;
-
- mdelay(20);
-
- /* Now enable the transmitter */
- ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
-
- if (ret_val)
- return ret_val;
-
- hw->dsp_config_state = e1000_dsp_config_enabled;
- }
-
- if (hw->ffe_config_state == e1000_ffe_config_active) {
- /* Save off the current value of register 0x2F5B to be restored at
- * the end of the routines. */
- ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
-
- if (ret_val)
- return ret_val;
-
- /* Disable the PHY transmitter */
- ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
-
- if (ret_val)
- return ret_val;
-
- mdelay(20);
-
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_FORCE_GIGA);
- if (ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
- IGP01E1000_PHY_DSP_FFE_DEFAULT);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_RESTART_AUTONEG);
- if (ret_val)
- return ret_val;
-
- mdelay(20);
-
- /* Now enable the transmitter */
- ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
-
- if (ret_val)
- return ret_val;
-
- hw->ffe_config_state = e1000_ffe_config_enabled;
- }
- }
- return E1000_SUCCESS;
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_read_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
}
-/*****************************************************************************
- * Set PHY to class A mode
- * Assumes the following operations will follow to enable the new class mode.
- * 1. Do a PHY soft reset
- * 2. Restart auto-negotiation or force link.
- *
- * hw - Struct containing variables accessed by shared code
- ****************************************************************************/
-static s32 e1000_set_phy_mode(struct e1000_hw *hw)
+static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
{
- s32 ret_val;
- u16 eeprom_data;
-
- DEBUGFUNC("e1000_set_phy_mode");
-
- if ((hw->mac_type == e1000_82545_rev_3) &&
- (hw->media_type == e1000_media_type_copper)) {
- ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data);
- if (ret_val) {
- return ret_val;
- }
-
- if ((eeprom_data != EEPROM_RESERVED_WORD) &&
- (eeprom_data & EEPROM_PHY_CLASS_A)) {
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B);
- if (ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104);
- if (ret_val)
- return ret_val;
-
- hw->phy_reset_disable = false;
- }
- }
-
- return E1000_SUCCESS;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 i = 0;
+
+ DEBUGFUNC("e1000_read_eeprom");
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if ((offset >= eeprom->word_size)
+ || (words > eeprom->word_size - offset) || (words == 0)) {
+ DEBUGOUT2
+ ("\"words\" parameter out of bounds. Words = %d, size = %d\n",
+ offset, eeprom->word_size);
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
+ * directly. In this case, we need to acquire the EEPROM so that
+ * FW or other port software does not interrupt.
+ */
+ /* Prepare the EEPROM for bit-bang reading */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
+ * acquired the EEPROM at this point, so any returns should release it */
+ if (eeprom->type == e1000_eeprom_spi) {
+ u16 word_in;
+ u8 read_opcode = EEPROM_READ_OPCODE_SPI;
+
+ if (e1000_spi_eeprom_ready(hw)) {
+ e1000_release_eeprom(hw);
+ return -E1000_ERR_EEPROM;
+ }
+
+ e1000_standby_eeprom(hw);
+
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ read_opcode |= EEPROM_A8_OPCODE_SPI;
+
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (u16) (offset * 2),
+ eeprom->address_bits);
+
+ /* Read the data. The address of the eeprom internally increments with
+ * each byte (spi) being read, saving on the overhead of eeprom setup
+ * and tear-down. The address counter will roll over if reading beyond
+ * the size of the eeprom, thus allowing the entire memory to be read
+ * starting from any offset. */
+ for (i = 0; i < words; i++) {
+ word_in = e1000_shift_in_ee_bits(hw, 16);
+ data[i] = (word_in >> 8) | (word_in << 8);
+ }
+ } else if (eeprom->type == e1000_eeprom_microwire) {
+ for (i = 0; i < words; i++) {
+ /* Send the READ command (opcode + addr) */
+ e1000_shift_out_ee_bits(hw,
+ EEPROM_READ_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+ e1000_shift_out_ee_bits(hw, (u16) (offset + i),
+ eeprom->address_bits);
+
+ /* Read the data. For microwire, each word requires the overhead
+ * of eeprom setup and tear-down. */
+ data[i] = e1000_shift_in_ee_bits(hw, 16);
+ e1000_standby_eeprom(hw);
+ }
+ }
+
+ /* End this read operation */
+ e1000_release_eeprom(hw);
+
+ return E1000_SUCCESS;
}
-/*****************************************************************************
+/**
+ * e1000_validate_eeprom_checksum - Verifies that the EEPROM has a valid checksum
+ * @hw: Struct containing variables accessed by shared code
*
- * This function sets the lplu state according to the active flag. When
- * activating lplu this function also disables smart speed and vise versa.
- * lplu will not be activated unless the device autonegotiation advertisment
- * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
- * hw: Struct containing variables accessed by shared code
- * active - true to enable lplu false to disable lplu.
- *
- * returns: - E1000_ERR_PHY if fail to read/write the PHY
- * E1000_SUCCESS at any other case.
- *
- ****************************************************************************/
-
-static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
+ * Reads the first 64 16 bit words of the EEPROM and sums the values read.
+ * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
+ * valid.
+ */
+s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw)
{
- u32 phy_ctrl = 0;
- s32 ret_val;
- u16 phy_data;
- DEBUGFUNC("e1000_set_d3_lplu_state");
-
- if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
- && hw->phy_type != e1000_phy_igp_3)
- return E1000_SUCCESS;
-
- /* During driver activity LPLU should not be used or it will attain link
- * from the lowest speeds starting from 10Mbps. The capability is used for
- * Dx transitions and states */
- if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
- if (ret_val)
- return ret_val;
- } else if (hw->mac_type == e1000_ich8lan) {
- /* MAC writes into PHY register based on the state transition
- * and start auto-negotiation. SW driver can overwrite the settings
- * in CSR PHY power control E1000_PHY_CTRL register. */
- phy_ctrl = er32(PHY_CTRL);
- } else {
- ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
- if (ret_val)
- return ret_val;
- }
-
- if (!active) {
- if (hw->mac_type == e1000_82541_rev_2 ||
- hw->mac_type == e1000_82547_rev_2) {
- phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
- if (ret_val)
- return ret_val;
- } else {
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data &= ~IGP02E1000_PM_D3_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
- phy_data);
- if (ret_val)
- return ret_val;
- }
- }
-
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
- * Dx states where the power conservation is most important. During
- * driver activity we should enable SmartSpeed, so performance is
- * maintained. */
- if (hw->smart_speed == e1000_smart_speed_on) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- } else if (hw->smart_speed == e1000_smart_speed_off) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- }
-
- } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) ||
- (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) ||
- (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {
-
- if (hw->mac_type == e1000_82541_rev_2 ||
- hw->mac_type == e1000_82547_rev_2) {
- phy_data |= IGP01E1000_GMII_FLEX_SPD;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data);
- if (ret_val)
- return ret_val;
- } else {
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data |= IGP02E1000_PM_D3_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
- phy_data);
- if (ret_val)
- return ret_val;
- }
- }
-
- /* When LPLU is enabled we should disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if (ret_val)
- return ret_val;
-
- }
- return E1000_SUCCESS;
+ u16 checksum = 0;
+ u16 i, eeprom_data;
+
+ DEBUGFUNC("e1000_validate_eeprom_checksum");
+
+ for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+
+ if (checksum == (u16) EEPROM_SUM)
+ return E1000_SUCCESS;
+ else {
+ DEBUGOUT("EEPROM Checksum Invalid\n");
+ return -E1000_ERR_EEPROM;
+ }
}
-/*****************************************************************************
- *
- * This function sets the lplu d0 state according to the active flag. When
- * activating lplu this function also disables smart speed and vise versa.
- * lplu will not be activated unless the device autonegotiation advertisment
- * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
- * hw: Struct containing variables accessed by shared code
- * active - true to enable lplu false to disable lplu.
+/**
+ * e1000_update_eeprom_checksum - Calculates/writes the EEPROM checksum
+ * @hw: Struct containing variables accessed by shared code
*
- * returns: - E1000_ERR_PHY if fail to read/write the PHY
- * E1000_SUCCESS at any other case.
+ * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA.
+ * Writes the difference to word offset 63 of the EEPROM.
+ */
+s32 e1000_update_eeprom_checksum(struct e1000_hw *hw)
+{
+ u16 checksum = 0;
+ u16 i, eeprom_data;
+
+ DEBUGFUNC("e1000_update_eeprom_checksum");
+
+ for (i = 0; i < EEPROM_CHECKSUM_REG; i++) {
+ if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ checksum += eeprom_data;
+ }
+ checksum = (u16) EEPROM_SUM - checksum;
+ if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) {
+ DEBUGOUT("EEPROM Write Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_write_eeprom - write words to the different EEPROM types.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: 16 bit word to be written to the EEPROM
*
- ****************************************************************************/
+ * If e1000_update_eeprom_checksum is not called after this function, the
+ * EEPROM will most likely contain an invalid checksum.
+ */
+s32 e1000_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
+{
+ s32 ret;
+ spin_lock(&e1000_eeprom_lock);
+ ret = e1000_do_write_eeprom(hw, offset, words, data);
+ spin_unlock(&e1000_eeprom_lock);
+ return ret;
+}
-static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
+static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
{
- u32 phy_ctrl = 0;
- s32 ret_val;
- u16 phy_data;
- DEBUGFUNC("e1000_set_d0_lplu_state");
-
- if (hw->mac_type <= e1000_82547_rev_2)
- return E1000_SUCCESS;
-
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl = er32(PHY_CTRL);
- } else {
- ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
- if (ret_val)
- return ret_val;
- }
-
- if (!active) {
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data &= ~IGP02E1000_PM_D0_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
- * Dx states where the power conservation is most important. During
- * driver activity we should enable SmartSpeed, so performance is
- * maintained. */
- if (hw->smart_speed == e1000_smart_speed_on) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- } else if (hw->smart_speed == e1000_smart_speed_off) {
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
- phy_data);
- if (ret_val)
- return ret_val;
- }
-
-
- } else {
-
- if (hw->mac_type == e1000_ich8lan) {
- phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
- ew32(PHY_CTRL, phy_ctrl);
- } else {
- phy_data |= IGP02E1000_PM_D0_LPLU;
- ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
- if (ret_val)
- return ret_val;
- }
-
- /* When LPLU is enabled we should disable SmartSpeed */
- ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data);
- if (ret_val)
- return ret_val;
-
- phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
- ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data);
- if (ret_val)
- return ret_val;
-
- }
- return E1000_SUCCESS;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ s32 status = 0;
+
+ DEBUGFUNC("e1000_write_eeprom");
+
+ /* If eeprom is not yet detected, do so now */
+ if (eeprom->word_size == 0)
+ e1000_init_eeprom_params(hw);
+
+ /* A check for invalid values: offset too large, too many words, and not
+ * enough words.
+ */
+ if ((offset >= eeprom->word_size)
+ || (words > eeprom->word_size - offset) || (words == 0)) {
+ DEBUGOUT("\"words\" parameter out of bounds\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Prepare the EEPROM for writing */
+ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
+ return -E1000_ERR_EEPROM;
+
+ if (eeprom->type == e1000_eeprom_microwire) {
+ status = e1000_write_eeprom_microwire(hw, offset, words, data);
+ } else {
+ status = e1000_write_eeprom_spi(hw, offset, words, data);
+ msleep(10);
+ }
+
+ /* Done with writing */
+ e1000_release_eeprom(hw);
+
+ return status;
}
-/******************************************************************************
- * Change VCO speed register to improve Bit Error Rate performance of SERDES.
- *
- * hw - Struct containing variables accessed by shared code
- *****************************************************************************/
-static s32 e1000_set_vco_speed(struct e1000_hw *hw)
+/**
+ * e1000_write_eeprom_spi - Writes a 16 bit word to a given offset in an SPI EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: pointer to array of 8 bit words to be written to the EEPROM
+ */
+static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words,
+ u16 *data)
{
- s32 ret_val;
- u16 default_page = 0;
- u16 phy_data;
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u16 widx = 0;
- DEBUGFUNC("e1000_set_vco_speed");
+ DEBUGFUNC("e1000_write_eeprom_spi");
- switch (hw->mac_type) {
- case e1000_82545_rev_3:
- case e1000_82546_rev_3:
- break;
- default:
- return E1000_SUCCESS;
- }
+ while (widx < words) {
+ u8 write_opcode = EEPROM_WRITE_OPCODE_SPI;
- /* Set PHY register 30, page 5, bit 8 to 0 */
+ if (e1000_spi_eeprom_ready(hw))
+ return -E1000_ERR_EEPROM;
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
- if (ret_val)
- return ret_val;
+ e1000_standby_eeprom(hw);
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
- if (ret_val)
- return ret_val;
+ /* Send the WRITE ENABLE command (8 bit opcode ) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI,
+ eeprom->opcode_bits);
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
+ e1000_standby_eeprom(hw);
- phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
- if (ret_val)
- return ret_val;
+ /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ if ((eeprom->address_bits == 8) && (offset >= 128))
+ write_opcode |= EEPROM_A8_OPCODE_SPI;
- /* Set PHY register 30, page 4, bit 11 to 1 */
+ /* Send the Write command (8-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits);
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
- if (ret_val)
- return ret_val;
+ e1000_shift_out_ee_bits(hw, (u16) ((offset + widx) * 2),
+ eeprom->address_bits);
- ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
- if (ret_val)
- return ret_val;
+ /* Send the data */
- phy_data |= M88E1000_PHY_VCO_REG_BIT11;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
- if (ret_val)
- return ret_val;
+ /* Loop to allow for up to whole page write (32 bytes) of eeprom */
+ while (widx < words) {
+ u16 word_out = data[widx];
+ word_out = (word_out >> 8) | (word_out << 8);
+ e1000_shift_out_ee_bits(hw, word_out, 16);
+ widx++;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
- if (ret_val)
- return ret_val;
+ /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
+ * operation, while the smaller eeproms are capable of an 8-byte
+ * PAGE WRITE operation. Break the inner loop to pass new address
+ */
+ if ((((offset + widx) * 2) % eeprom->page_size) == 0) {
+ e1000_standby_eeprom(hw);
+ break;
+ }
+ }
+ }
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
+/**
+ * e1000_write_eeprom_microwire - Writes a 16 bit word to a given offset in a Microwire EEPROM.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset within the EEPROM to be written to
+ * @words: number of words to write
+ * @data: pointer to array of 8 bit words to be written to the EEPROM
+ */
+static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
+ u16 words, u16 *data)
+{
+ struct e1000_eeprom_info *eeprom = &hw->eeprom;
+ u32 eecd;
+ u16 words_written = 0;
+ u16 i = 0;
+
+ DEBUGFUNC("e1000_write_eeprom_microwire");
+
+ /* Send the write enable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 11). It's less work to include
+ * the 11 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This puts the
+ * EEPROM into write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE,
+ (u16) (eeprom->opcode_bits + 2));
+
+ e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2));
+
+ /* Prepare the EEPROM */
+ e1000_standby_eeprom(hw);
+
+ while (words_written < words) {
+ /* Send the Write command (3-bit opcode + addr) */
+ e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE,
+ eeprom->opcode_bits);
+
+ e1000_shift_out_ee_bits(hw, (u16) (offset + words_written),
+ eeprom->address_bits);
+
+ /* Send the data */
+ e1000_shift_out_ee_bits(hw, data[words_written], 16);
+
+ /* Toggle the CS line. This in effect tells the EEPROM to execute
+ * the previous command.
+ */
+ e1000_standby_eeprom(hw);
+
+ /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
+ * signal that the command has been completed by raising the DO signal.
+ * If DO does not go high in 10 milliseconds, then error out.
+ */
+ for (i = 0; i < 200; i++) {
+ eecd = er32(EECD);
+ if (eecd & E1000_EECD_DO)
+ break;
+ udelay(50);
+ }
+ if (i == 200) {
+ DEBUGOUT("EEPROM Write did not complete\n");
+ return -E1000_ERR_EEPROM;
+ }
+
+ /* Recover from write */
+ e1000_standby_eeprom(hw);
-/*****************************************************************************
- * This function reads the cookie from ARC ram.
+ words_written++;
+ }
+
+ /* Send the write disable command to the EEPROM (3-bit opcode plus
+ * 6/8-bit dummy address beginning with 10). It's less work to include
+ * the 10 of the dummy address as part of the opcode than it is to shift
+ * it over the correct number of bits for the address. This takes the
+ * EEPROM out of write/erase mode.
+ */
+ e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE,
+ (u16) (eeprom->opcode_bits + 2));
+
+ e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2));
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_read_mac_addr - read the adapters MAC from eeprom
+ * @hw: Struct containing variables accessed by shared code
*
- * returns: - E1000_SUCCESS .
- ****************************************************************************/
-static s32 e1000_host_if_read_cookie(struct e1000_hw *hw, u8 *buffer)
+ * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
+ * second function of dual function devices
+ */
+s32 e1000_read_mac_addr(struct e1000_hw *hw)
{
- u8 i;
- u32 offset = E1000_MNG_DHCP_COOKIE_OFFSET;
- u8 length = E1000_MNG_DHCP_COOKIE_LENGTH;
-
- length = (length >> 2);
- offset = (offset >> 2);
-
- for (i = 0; i < length; i++) {
- *((u32 *)buffer + i) =
- E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i);
- }
- return E1000_SUCCESS;
-}
+ u16 offset;
+ u16 eeprom_data, i;
+ DEBUGFUNC("e1000_read_mac_addr");
-/*****************************************************************************
- * This function checks whether the HOST IF is enabled for command operaton
- * and also checks whether the previous command is completed.
- * It busy waits in case of previous command is not completed.
+ for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
+ offset = i >> 1;
+ if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
+ hw->perm_mac_addr[i] = (u8) (eeprom_data & 0x00FF);
+ hw->perm_mac_addr[i + 1] = (u8) (eeprom_data >> 8);
+ }
+
+ switch (hw->mac_type) {
+ default:
+ break;
+ case e1000_82546:
+ case e1000_82546_rev_3:
+ if (er32(STATUS) & E1000_STATUS_FUNC_1)
+ hw->perm_mac_addr[5] ^= 0x01;
+ break;
+ }
+
+ for (i = 0; i < NODE_ADDRESS_SIZE; i++)
+ hw->mac_addr[i] = hw->perm_mac_addr[i];
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_init_rx_addrs - Initializes receive address filters.
+ * @hw: Struct containing variables accessed by shared code
*
- * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or
- * timeout
- * - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_enable_host_if(struct e1000_hw *hw)
+ * Places the MAC address in receive address register 0 and clears the rest
+ * of the receive address registers. Clears the multicast table. Assumes
+ * the receiver is in reset when the routine is called.
+ */
+static void e1000_init_rx_addrs(struct e1000_hw *hw)
{
- u32 hicr;
- u8 i;
-
- /* Check that the host interface is enabled. */
- hicr = er32(HICR);
- if ((hicr & E1000_HICR_EN) == 0) {
- DEBUGOUT("E1000_HOST_EN bit disabled.\n");
- return -E1000_ERR_HOST_INTERFACE_COMMAND;
- }
- /* check the previous command is completed */
- for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) {
- hicr = er32(HICR);
- if (!(hicr & E1000_HICR_C))
- break;
- mdelay(1);
- }
-
- if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
- DEBUGOUT("Previous command timeout failed .\n");
- return -E1000_ERR_HOST_INTERFACE_COMMAND;
- }
- return E1000_SUCCESS;
+ u32 i;
+ u32 rar_num;
+
+ DEBUGFUNC("e1000_init_rx_addrs");
+
+ /* Setup the receive address. */
+ DEBUGOUT("Programming MAC Address into RAR[0]\n");
+
+ e1000_rar_set(hw, hw->mac_addr, 0);
+
+ rar_num = E1000_RAR_ENTRIES;
+
+ /* Zero out the other 15 receive addresses. */
+ DEBUGOUT("Clearing RAR[1-15]\n");
+ for (i = 1; i < rar_num; i++) {
+ E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
+ E1000_WRITE_FLUSH();
+ }
}
-/*****************************************************************************
- * This function writes the buffer content at the offset given on the host if.
- * It also does alignment considerations to do the writes in most efficient way.
- * Also fills up the sum of the buffer in *buffer parameter.
- *
- * returns - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer, u16 length,
- u16 offset, u8 *sum)
+/**
+ * e1000_hash_mc_addr - Hashes an address to determine its location in the multicast table
+ * @hw: Struct containing variables accessed by shared code
+ * @mc_addr: the multicast address to hash
+ */
+u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
{
- u8 *tmp;
- u8 *bufptr = buffer;
- u32 data = 0;
- u16 remaining, i, j, prev_bytes;
-
- /* sum = only sum of the data and it is not checksum */
-
- if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) {
- return -E1000_ERR_PARAM;
- }
-
- tmp = (u8 *)&data;
- prev_bytes = offset & 0x3;
- offset &= 0xFFFC;
- offset >>= 2;
-
- if (prev_bytes) {
- data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset);
- for (j = prev_bytes; j < sizeof(u32); j++) {
- *(tmp + j) = *bufptr++;
- *sum += *(tmp + j);
- }
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data);
- length -= j - prev_bytes;
- offset++;
- }
-
- remaining = length & 0x3;
- length -= remaining;
-
- /* Calculate length in DWORDs */
- length >>= 2;
-
- /* The device driver writes the relevant command block into the
- * ram area. */
- for (i = 0; i < length; i++) {
- for (j = 0; j < sizeof(u32); j++) {
- *(tmp + j) = *bufptr++;
- *sum += *(tmp + j);
- }
-
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
- }
- if (remaining) {
- for (j = 0; j < sizeof(u32); j++) {
- if (j < remaining)
- *(tmp + j) = *bufptr++;
- else
- *(tmp + j) = 0;
-
- *sum += *(tmp + j);
- }
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data);
- }
-
- return E1000_SUCCESS;
+ u32 hash_value = 0;
+
+ /* The portion of the address that is used for the hash table is
+ * determined by the mc_filter_type setting.
+ */
+ switch (hw->mc_filter_type) {
+ /* [0] [1] [2] [3] [4] [5]
+ * 01 AA 00 12 34 56
+ * LSB MSB
+ */
+ case 0:
+ /* [47:36] i.e. 0x563 for above example address */
+ hash_value = ((mc_addr[4] >> 4) | (((u16) mc_addr[5]) << 4));
+ break;
+ case 1:
+ /* [46:35] i.e. 0xAC6 for above example address */
+ hash_value = ((mc_addr[4] >> 3) | (((u16) mc_addr[5]) << 5));
+ break;
+ case 2:
+ /* [45:34] i.e. 0x5D8 for above example address */
+ hash_value = ((mc_addr[4] >> 2) | (((u16) mc_addr[5]) << 6));
+ break;
+ case 3:
+ /* [43:32] i.e. 0x634 for above example address */
+ hash_value = ((mc_addr[4]) | (((u16) mc_addr[5]) << 8));
+ break;
+ }
+
+ hash_value &= 0xFFF;
+ return hash_value;
}
+/**
+ * e1000_rar_set - Puts an ethernet address into a receive address register.
+ * @hw: Struct containing variables accessed by shared code
+ * @addr: Address to put into receive address register
+ * @index: Receive address register to write
+ */
+void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index)
+{
+ u32 rar_low, rar_high;
-/*****************************************************************************
- * This function writes the command header after does the checksum calculation.
- *
- * returns - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_write_cmd_header(struct e1000_hw *hw,
- struct e1000_host_mng_command_header *hdr)
+ /* HW expects these in little endian so we reverse the byte order
+ * from network order (big endian) to little endian
+ */
+ rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) |
+ ((u32) addr[2] << 16) | ((u32) addr[3] << 24));
+ rar_high = ((u32) addr[4] | ((u32) addr[5] << 8));
+
+ /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx
+ * unit hang.
+ *
+ * Description:
+ * If there are any Rx frames queued up or otherwise present in the HW
+ * before RSS is enabled, and then we enable RSS, the HW Rx unit will
+ * hang. To work around this issue, we have to disable receives and
+ * flush out all Rx frames before we enable RSS. To do so, we modify we
+ * redirect all Rx traffic to manageability and then reset the HW.
+ * This flushes away Rx frames, and (since the redirections to
+ * manageability persists across resets) keeps new ones from coming in
+ * while we work. Then, we clear the Address Valid AV bit for all MAC
+ * addresses and undo the re-direction to manageability.
+ * Now, frames are coming in again, but the MAC won't accept them, so
+ * far so good. We now proceed to initialize RSS (if necessary) and
+ * configure the Rx unit. Last, we re-enable the AV bits and continue
+ * on our merry way.
+ */
+ switch (hw->mac_type) {
+ default:
+ /* Indicate to hardware the Address is Valid. */
+ rar_high |= E1000_RAH_AV;
+ break;
+ }
+
+ E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high);
+ E1000_WRITE_FLUSH();
+}
+
+/**
+ * e1000_write_vfta - Writes a value to the specified offset in the VLAN filter table.
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: Offset in VLAN filer table to write
+ * @value: Value to write into VLAN filter table
+ */
+void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value)
{
- u16 i;
- u8 sum;
- u8 *buffer;
+ u32 temp;
+
+ if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) {
+ temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1));
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_FLUSH();
+ E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp);
+ E1000_WRITE_FLUSH();
+ } else {
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value);
+ E1000_WRITE_FLUSH();
+ }
+}
- /* Write the whole command header structure which includes sum of
- * the buffer */
+/**
+ * e1000_clear_vfta - Clears the VLAN filer table
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_clear_vfta(struct e1000_hw *hw)
+{
+ u32 offset;
+ u32 vfta_value = 0;
+ u32 vfta_offset = 0;
+ u32 vfta_bit_in_reg = 0;
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ /* If the offset we want to clear is the same offset of the
+ * manageability VLAN ID, then clear all bits except that of the
+ * manageability unit */
+ vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
+ E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
+ E1000_WRITE_FLUSH();
+ }
+}
- u16 length = sizeof(struct e1000_host_mng_command_header);
+static s32 e1000_id_led_init(struct e1000_hw *hw)
+{
+ u32 ledctl;
+ const u32 ledctl_mask = 0x000000FF;
+ const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+ const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+ u16 eeprom_data, i, temp;
+ const u16 led_mask = 0x0F;
- sum = hdr->checksum;
- hdr->checksum = 0;
+ DEBUGFUNC("e1000_id_led_init");
- buffer = (u8 *)hdr;
- i = length;
- while (i--)
- sum += buffer[i];
+ if (hw->mac_type < e1000_82540) {
+ /* Nothing to do */
+ return E1000_SUCCESS;
+ }
- hdr->checksum = 0 - sum;
+ ledctl = er32(LEDCTL);
+ hw->ledctl_default = ledctl;
+ hw->ledctl_mode1 = hw->ledctl_default;
+ hw->ledctl_mode2 = hw->ledctl_default;
- length >>= 2;
- /* The device driver writes the relevant command block into the ram area. */
- for (i = 0; i < length; i++) {
- E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((u32 *)hdr + i));
- E1000_WRITE_FLUSH();
- }
+ if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) {
+ DEBUGOUT("EEPROM Read Error\n");
+ return -E1000_ERR_EEPROM;
+ }
- return E1000_SUCCESS;
-}
+ if ((eeprom_data == ID_LED_RESERVED_0000) ||
+ (eeprom_data == ID_LED_RESERVED_FFFF)) {
+ eeprom_data = ID_LED_DEFAULT;
+ }
+ for (i = 0; i < 4; i++) {
+ temp = (eeprom_data >> (i << 2)) & led_mask;
+ switch (temp) {
+ case ID_LED_ON1_DEF2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_ON1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_OFF1_DEF2:
+ case ID_LED_OFF1_ON2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode1 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ switch (temp) {
+ case ID_LED_DEF1_ON2:
+ case ID_LED_ON1_ON2:
+ case ID_LED_OFF1_ON2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_on << (i << 3);
+ break;
+ case ID_LED_DEF1_OFF2:
+ case ID_LED_ON1_OFF2:
+ case ID_LED_OFF1_OFF2:
+ hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+ hw->ledctl_mode2 |= ledctl_off << (i << 3);
+ break;
+ default:
+ /* Do nothing */
+ break;
+ }
+ }
+ return E1000_SUCCESS;
+}
-/*****************************************************************************
- * This function indicates to ARC that a new command is pending which completes
- * one write operation by the driver.
+/**
+ * e1000_setup_led
+ * @hw: Struct containing variables accessed by shared code
*
- * returns - E1000_SUCCESS for success.
- ****************************************************************************/
-static s32 e1000_mng_write_commit(struct e1000_hw *hw)
+ * Prepares SW controlable LED for use and saves the current state of the LED.
+ */
+s32 e1000_setup_led(struct e1000_hw *hw)
{
- u32 hicr;
+ u32 ledctl;
+ s32 ret_val = E1000_SUCCESS;
- hicr = er32(HICR);
- /* Setting this bit tells the ARC that a new command is pending. */
- ew32(HICR, hicr | E1000_HICR_C);
+ DEBUGFUNC("e1000_setup_led");
- return E1000_SUCCESS;
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No setup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn off PHY Smart Power Down (if enabled) */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ &hw->phy_spd_default);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ (u16) (hw->phy_spd_default &
+ ~IGP01E1000_GMII_SPD));
+ if (ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ ledctl = er32(LEDCTL);
+ /* Save current LEDCTL settings */
+ hw->ledctl_default = ledctl;
+ /* Turn off LED0 */
+ ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+ E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_LED0_MODE_MASK);
+ ledctl |= (E1000_LEDCTL_MODE_LED_OFF <<
+ E1000_LEDCTL_LED0_MODE_SHIFT);
+ ew32(LEDCTL, ledctl);
+ } else if (hw->media_type == e1000_media_type_copper)
+ ew32(LEDCTL, hw->ledctl_mode1);
+ break;
+ }
+
+ return E1000_SUCCESS;
}
+/**
+ * e1000_cleanup_led - Restores the saved state of the SW controlable LED.
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_cleanup_led(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_cleanup_led");
-/*****************************************************************************
- * This function checks the mode of the firmware.
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ case e1000_82544:
+ /* No cleanup necessary */
+ break;
+ case e1000_82541:
+ case e1000_82547:
+ case e1000_82541_rev_2:
+ case e1000_82547_rev_2:
+ /* Turn on PHY Smart Power Down (if previously enabled) */
+ ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ hw->phy_spd_default);
+ if (ret_val)
+ return ret_val;
+ /* Fall Through */
+ default:
+ /* Restore LEDCTL settings */
+ ew32(LEDCTL, hw->ledctl_default);
+ break;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_on - Turns on the software controllable LED
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_led_on(struct e1000_hw *hw)
+{
+ u32 ctrl = er32(CTRL);
+
+ DEBUGFUNC("e1000_led_on");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn on the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn on the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if (hw->media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->ledctl_mode2);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_led_off - Turns off the software controllable LED
+ * @hw: Struct containing variables accessed by shared code
+ */
+s32 e1000_led_off(struct e1000_hw *hw)
+{
+ u32 ctrl = er32(CTRL);
+
+ DEBUGFUNC("e1000_led_off");
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ case e1000_82543:
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ break;
+ case e1000_82544:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Clear SW Defineable Pin 0 to turn off the LED */
+ ctrl &= ~E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ }
+ break;
+ default:
+ if (hw->media_type == e1000_media_type_fiber) {
+ /* Set SW Defineable Pin 0 to turn off the LED */
+ ctrl |= E1000_CTRL_SWDPIN0;
+ ctrl |= E1000_CTRL_SWDPIO0;
+ } else if (hw->media_type == e1000_media_type_copper) {
+ ew32(LEDCTL, hw->ledctl_mode1);
+ return E1000_SUCCESS;
+ }
+ break;
+ }
+
+ ew32(CTRL, ctrl);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_clear_hw_cntrs - Clears all hardware statistics counters.
+ * @hw: Struct containing variables accessed by shared code
+ */
+static void e1000_clear_hw_cntrs(struct e1000_hw *hw)
+{
+ volatile u32 temp;
+
+ temp = er32(CRCERRS);
+ temp = er32(SYMERRS);
+ temp = er32(MPC);
+ temp = er32(SCC);
+ temp = er32(ECOL);
+ temp = er32(MCC);
+ temp = er32(LATECOL);
+ temp = er32(COLC);
+ temp = er32(DC);
+ temp = er32(SEC);
+ temp = er32(RLEC);
+ temp = er32(XONRXC);
+ temp = er32(XONTXC);
+ temp = er32(XOFFRXC);
+ temp = er32(XOFFTXC);
+ temp = er32(FCRUC);
+
+ temp = er32(PRC64);
+ temp = er32(PRC127);
+ temp = er32(PRC255);
+ temp = er32(PRC511);
+ temp = er32(PRC1023);
+ temp = er32(PRC1522);
+
+ temp = er32(GPRC);
+ temp = er32(BPRC);
+ temp = er32(MPRC);
+ temp = er32(GPTC);
+ temp = er32(GORCL);
+ temp = er32(GORCH);
+ temp = er32(GOTCL);
+ temp = er32(GOTCH);
+ temp = er32(RNBC);
+ temp = er32(RUC);
+ temp = er32(RFC);
+ temp = er32(ROC);
+ temp = er32(RJC);
+ temp = er32(TORL);
+ temp = er32(TORH);
+ temp = er32(TOTL);
+ temp = er32(TOTH);
+ temp = er32(TPR);
+ temp = er32(TPT);
+
+ temp = er32(PTC64);
+ temp = er32(PTC127);
+ temp = er32(PTC255);
+ temp = er32(PTC511);
+ temp = er32(PTC1023);
+ temp = er32(PTC1522);
+
+ temp = er32(MPTC);
+ temp = er32(BPTC);
+
+ if (hw->mac_type < e1000_82543)
+ return;
+
+ temp = er32(ALGNERRC);
+ temp = er32(RXERRC);
+ temp = er32(TNCRS);
+ temp = er32(CEXTERR);
+ temp = er32(TSCTC);
+ temp = er32(TSCTFC);
+
+ if (hw->mac_type <= e1000_82544)
+ return;
+
+ temp = er32(MGTPRC);
+ temp = er32(MGTPDC);
+ temp = er32(MGTPTC);
+}
+
+/**
+ * e1000_reset_adaptive - Resets Adaptive IFS to its default state.
+ * @hw: Struct containing variables accessed by shared code
*
- * returns - true when the mode is IAMT or false.
- ****************************************************************************/
-bool e1000_check_mng_mode(struct e1000_hw *hw)
+ * Call this after e1000_init_hw. You may override the IFS defaults by setting
+ * hw->ifs_params_forced to true. However, you must initialize hw->
+ * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio
+ * before calling this function.
+ */
+void e1000_reset_adaptive(struct e1000_hw *hw)
{
- u32 fwsm;
-
- fwsm = er32(FWSM);
-
- if (hw->mac_type == e1000_ich8lan) {
- if ((fwsm & E1000_FWSM_MODE_MASK) ==
- (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
- return true;
- } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
- (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
- return true;
+ DEBUGFUNC("e1000_reset_adaptive");
- return false;
+ if (hw->adaptive_ifs) {
+ if (!hw->ifs_params_forced) {
+ hw->current_ifs_val = 0;
+ hw->ifs_min_val = IFS_MIN;
+ hw->ifs_max_val = IFS_MAX;
+ hw->ifs_step_size = IFS_STEP;
+ hw->ifs_ratio = IFS_RATIO;
+ }
+ hw->in_ifs_mode = false;
+ ew32(AIT, 0);
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
+ }
}
-
-/*****************************************************************************
- * This function writes the dhcp info .
- ****************************************************************************/
-s32 e1000_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length)
+/**
+ * e1000_update_adaptive - update adaptive IFS
+ * @hw: Struct containing variables accessed by shared code
+ * @tx_packets: Number of transmits since last callback
+ * @total_collisions: Number of collisions since last callback
+ *
+ * Called during the callback/watchdog routine to update IFS value based on
+ * the ratio of transmits to collisions.
+ */
+void e1000_update_adaptive(struct e1000_hw *hw)
{
- s32 ret_val;
- struct e1000_host_mng_command_header hdr;
-
- hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD;
- hdr.command_length = length;
- hdr.reserved1 = 0;
- hdr.reserved2 = 0;
- hdr.checksum = 0;
-
- ret_val = e1000_mng_enable_host_if(hw);
- if (ret_val == E1000_SUCCESS) {
- ret_val = e1000_mng_host_if_write(hw, buffer, length, sizeof(hdr),
- &(hdr.checksum));
- if (ret_val == E1000_SUCCESS) {
- ret_val = e1000_mng_write_cmd_header(hw, &hdr);
- if (ret_val == E1000_SUCCESS)
- ret_val = e1000_mng_write_commit(hw);
- }
- }
- return ret_val;
+ DEBUGFUNC("e1000_update_adaptive");
+
+ if (hw->adaptive_ifs) {
+ if ((hw->collision_delta *hw->ifs_ratio) > hw->tx_packet_delta) {
+ if (hw->tx_packet_delta > MIN_NUM_XMITS) {
+ hw->in_ifs_mode = true;
+ if (hw->current_ifs_val < hw->ifs_max_val) {
+ if (hw->current_ifs_val == 0)
+ hw->current_ifs_val =
+ hw->ifs_min_val;
+ else
+ hw->current_ifs_val +=
+ hw->ifs_step_size;
+ ew32(AIT, hw->current_ifs_val);
+ }
+ }
+ } else {
+ if (hw->in_ifs_mode
+ && (hw->tx_packet_delta <= MIN_NUM_XMITS)) {
+ hw->current_ifs_val = 0;
+ hw->in_ifs_mode = false;
+ ew32(AIT, 0);
+ }
+ }
+ } else {
+ DEBUGOUT("Not in Adaptive IFS mode!\n");
+ }
}
-
-/*****************************************************************************
- * This function calculates the checksum.
+/**
+ * e1000_tbi_adjust_stats
+ * @hw: Struct containing variables accessed by shared code
+ * @frame_len: The length of the frame in question
+ * @mac_addr: The Ethernet destination address of the frame in question
*
- * returns - checksum of buffer contents.
- ****************************************************************************/
-static u8 e1000_calculate_mng_checksum(char *buffer, u32 length)
+ * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
+ */
+void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
+ u32 frame_len, u8 *mac_addr)
{
- u8 sum = 0;
- u32 i;
-
- if (!buffer)
- return 0;
+ u64 carry_bit;
- for (i=0; i < length; i++)
- sum += buffer[i];
+ /* First adjust the frame length. */
+ frame_len--;
+ /* We need to adjust the statistics counters, since the hardware
+ * counters overcount this packet as a CRC error and undercount
+ * the packet as a good packet
+ */
+ /* This packet should not be counted as a CRC error. */
+ stats->crcerrs--;
+ /* This packet does count as a Good Packet Received. */
+ stats->gprc++;
+
+ /* Adjust the Good Octets received counters */
+ carry_bit = 0x80000000 & stats->gorcl;
+ stats->gorcl += frame_len;
+ /* If the high bit of Gorcl (the low 32 bits of the Good Octets
+ * Received Count) was one before the addition,
+ * AND it is zero after, then we lost the carry out,
+ * need to add one to Gorch (Good Octets Received Count High).
+ * This could be simplified if all environments supported
+ * 64-bit integers.
+ */
+ if (carry_bit && ((stats->gorcl & 0x80000000) == 0))
+ stats->gorch++;
+ /* Is this a broadcast or multicast? Check broadcast first,
+ * since the test for a multicast frame will test positive on
+ * a broadcast frame.
+ */
+ if ((mac_addr[0] == (u8) 0xff) && (mac_addr[1] == (u8) 0xff))
+ /* Broadcast packet */
+ stats->bprc++;
+ else if (*mac_addr & 0x01)
+ /* Multicast packet */
+ stats->mprc++;
+
+ if (frame_len == hw->max_frame_size) {
+ /* In this case, the hardware has overcounted the number of
+ * oversize frames.
+ */
+ if (stats->roc > 0)
+ stats->roc--;
+ }
- return (u8)(0 - sum);
+ /* Adjust the bin counters when the extra byte put the frame in the
+ * wrong bin. Remember that the frame_len was adjusted above.
+ */
+ if (frame_len == 64) {
+ stats->prc64++;
+ stats->prc127--;
+ } else if (frame_len == 127) {
+ stats->prc127++;
+ stats->prc255--;
+ } else if (frame_len == 255) {
+ stats->prc255++;
+ stats->prc511--;
+ } else if (frame_len == 511) {
+ stats->prc511++;
+ stats->prc1023--;
+ } else if (frame_len == 1023) {
+ stats->prc1023++;
+ stats->prc1522--;
+ } else if (frame_len == 1522) {
+ stats->prc1522++;
+ }
}
-/*****************************************************************************
- * This function checks whether tx pkt filtering needs to be enabled or not.
+/**
+ * e1000_get_bus_info
+ * @hw: Struct containing variables accessed by shared code
*
- * returns - true for packet filtering or false.
- ****************************************************************************/
-bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw)
+ * Gets the current PCI bus type, speed, and width of the hardware
+ */
+void e1000_get_bus_info(struct e1000_hw *hw)
{
- /* called in init as well as watchdog timer functions */
-
- s32 ret_val, checksum;
- bool tx_filter = false;
- struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie);
- u8 *buffer = (u8 *) &(hw->mng_cookie);
-
- if (e1000_check_mng_mode(hw)) {
- ret_val = e1000_mng_enable_host_if(hw);
- if (ret_val == E1000_SUCCESS) {
- ret_val = e1000_host_if_read_cookie(hw, buffer);
- if (ret_val == E1000_SUCCESS) {
- checksum = hdr->checksum;
- hdr->checksum = 0;
- if ((hdr->signature == E1000_IAMT_SIGNATURE) &&
- checksum == e1000_calculate_mng_checksum((char *)buffer,
- E1000_MNG_DHCP_COOKIE_LENGTH)) {
- if (hdr->status &
- E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT)
- tx_filter = true;
- } else
- tx_filter = true;
- } else
- tx_filter = true;
- }
- }
-
- hw->tx_pkt_filtering = tx_filter;
- return tx_filter;
+ u32 status;
+
+ switch (hw->mac_type) {
+ case e1000_82542_rev2_0:
+ case e1000_82542_rev2_1:
+ hw->bus_type = e1000_bus_type_pci;
+ hw->bus_speed = e1000_bus_speed_unknown;
+ hw->bus_width = e1000_bus_width_unknown;
+ break;
+ default:
+ status = er32(STATUS);
+ hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ?
+ e1000_bus_type_pcix : e1000_bus_type_pci;
+
+ if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) {
+ hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ?
+ e1000_bus_speed_66 : e1000_bus_speed_120;
+ } else if (hw->bus_type == e1000_bus_type_pci) {
+ hw->bus_speed = (status & E1000_STATUS_PCI66) ?
+ e1000_bus_speed_66 : e1000_bus_speed_33;
+ } else {
+ switch (status & E1000_STATUS_PCIX_SPEED) {
+ case E1000_STATUS_PCIX_SPEED_66:
+ hw->bus_speed = e1000_bus_speed_66;
+ break;
+ case E1000_STATUS_PCIX_SPEED_100:
+ hw->bus_speed = e1000_bus_speed_100;
+ break;
+ case E1000_STATUS_PCIX_SPEED_133:
+ hw->bus_speed = e1000_bus_speed_133;
+ break;
+ default:
+ hw->bus_speed = e1000_bus_speed_reserved;
+ break;
+ }
+ }
+ hw->bus_width = (status & E1000_STATUS_BUS64) ?
+ e1000_bus_width_64 : e1000_bus_width_32;
+ break;
+ }
}
-/******************************************************************************
- * Verifies the hardware needs to allow ARPs to be processed by the host
- *
- * hw - Struct containing variables accessed by shared code
- *
- * returns: - true/false
+/**
+ * e1000_write_reg_io
+ * @hw: Struct containing variables accessed by shared code
+ * @offset: offset to write to
+ * @value: value to write
*
- *****************************************************************************/
-u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw)
+ * Writes a value to one of the devices registers using port I/O (as opposed to
+ * memory mapped I/O). Only 82544 and newer devices support port I/O.
+ */
+static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value)
{
- u32 manc;
- u32 fwsm, factps;
-
- if (hw->asf_firmware_present) {
- manc = er32(MANC);
-
- if (!(manc & E1000_MANC_RCV_TCO_EN) ||
- !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
- return false;
- if (e1000_arc_subsystem_valid(hw)) {
- fwsm = er32(FWSM);
- factps = er32(FACTPS);
-
- if ((((fwsm & E1000_FWSM_MODE_MASK) >> E1000_FWSM_MODE_SHIFT) ==
- e1000_mng_mode_pt) && !(factps & E1000_FACTPS_MNGCG))
- return true;
- } else
- if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
- return true;
- }
- return false;
-}
+ unsigned long io_addr = hw->io_base;
+ unsigned long io_data = hw->io_base + 4;
-static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw)
-{
- s32 ret_val;
- u16 mii_status_reg;
- u16 i;
-
- /* Polarity reversal workaround for forced 10F/10H links. */
-
- /* Disable the transmitter on the PHY */
-
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
- if (ret_val)
- return ret_val;
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
- if (ret_val)
- return ret_val;
-
- /* This loop will early-out if the NO link condition has been met. */
- for (i = PHY_FORCE_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Link Status bit
- * to be clear.
- */
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break;
- mdelay(100);
- }
-
- /* Recommended delay time after link has been lost */
- mdelay(1000);
-
- /* Now we will re-enable th transmitter on the PHY */
-
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
- if (ret_val)
- return ret_val;
- mdelay(50);
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0);
- if (ret_val)
- return ret_val;
- mdelay(50);
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00);
- if (ret_val)
- return ret_val;
- mdelay(50);
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
- if (ret_val)
- return ret_val;
-
- /* This loop will early-out if the link condition has been met. */
- for (i = PHY_FORCE_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Link Status bit
- * to be set.
- */
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
- if (ret_val)
- return ret_val;
-
- if (mii_status_reg & MII_SR_LINK_STATUS) break;
- mdelay(100);
- }
- return E1000_SUCCESS;
+ e1000_io_write(hw, io_addr, offset);
+ e1000_io_write(hw, io_data, value);
}
-/***************************************************************************
+/**
+ * e1000_get_cable_length - Estimates the cable length.
+ * @hw: Struct containing variables accessed by shared code
+ * @min_length: The estimated minimum length
+ * @max_length: The estimated maximum length
*
- * Disables PCI-Express master access.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - none.
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
*
- ***************************************************************************/
-static void e1000_set_pci_express_master_disable(struct e1000_hw *hw)
+ * This function always returns a ranged length (minimum & maximum).
+ * So for M88 phy's, this function interprets the one value returned from the
+ * register to the minimum and maximum range.
+ * For IGP phy's, the function calculates the range by the AGC registers.
+ */
+static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length,
+ u16 *max_length)
{
- u32 ctrl;
-
- DEBUGFUNC("e1000_set_pci_express_master_disable");
+ s32 ret_val;
+ u16 agc_value = 0;
+ u16 i, phy_data;
+ u16 cable_length;
- if (hw->bus_type != e1000_bus_type_pci_express)
- return;
+ DEBUGFUNC("e1000_get_cable_length");
- ctrl = er32(CTRL);
- ctrl |= E1000_CTRL_GIO_MASTER_DISABLE;
- ew32(CTRL, ctrl);
-}
+ *min_length = *max_length = 0;
-/*******************************************************************************
- *
- * Disables PCI-Express master access and verifies there are no pending requests
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't
- * caused the master requests to be disabled.
- * E1000_SUCCESS master requests disabled.
- *
- ******************************************************************************/
-s32 e1000_disable_pciex_master(struct e1000_hw *hw)
-{
- s32 timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */
+ /* Use old method for Phy older than IGP */
+ if (hw->phy_type == e1000_phy_m88) {
- DEBUGFUNC("e1000_disable_pciex_master");
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
+ M88E1000_PSSR_CABLE_LENGTH_SHIFT;
- if (hw->bus_type != e1000_bus_type_pci_express)
- return E1000_SUCCESS;
+ /* Convert the enum value to ranged values */
+ switch (cable_length) {
+ case e1000_cable_length_50:
+ *min_length = 0;
+ *max_length = e1000_igp_cable_length_50;
+ break;
+ case e1000_cable_length_50_80:
+ *min_length = e1000_igp_cable_length_50;
+ *max_length = e1000_igp_cable_length_80;
+ break;
+ case e1000_cable_length_80_110:
+ *min_length = e1000_igp_cable_length_80;
+ *max_length = e1000_igp_cable_length_110;
+ break;
+ case e1000_cable_length_110_140:
+ *min_length = e1000_igp_cable_length_110;
+ *max_length = e1000_igp_cable_length_140;
+ break;
+ case e1000_cable_length_140:
+ *min_length = e1000_igp_cable_length_140;
+ *max_length = e1000_igp_cable_length_170;
+ break;
+ default:
+ return -E1000_ERR_PHY;
+ break;
+ }
+ } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */
+ u16 cur_agc_value;
+ u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE;
+ u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ { IGP01E1000_PHY_AGC_A,
+ IGP01E1000_PHY_AGC_B,
+ IGP01E1000_PHY_AGC_C,
+ IGP01E1000_PHY_AGC_D
+ };
+ /* Read the AGC registers for all channels */
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+
+ ret_val =
+ e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT;
+
+ /* Value bound check. */
+ if ((cur_agc_value >=
+ IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1)
+ || (cur_agc_value == 0))
+ return -E1000_ERR_PHY;
+
+ agc_value += cur_agc_value;
+
+ /* Update minimal AGC value. */
+ if (min_agc_value > cur_agc_value)
+ min_agc_value = cur_agc_value;
+ }
- e1000_set_pci_express_master_disable(hw);
+ /* Remove the minimal AGC result for length < 50m */
+ if (agc_value <
+ IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) {
+ agc_value -= min_agc_value;
- while (timeout) {
- if (!(er32(STATUS) & E1000_STATUS_GIO_MASTER_ENABLE))
- break;
- else
- udelay(100);
- timeout--;
- }
+ /* Get the average length of the remaining 3 channels */
+ agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1);
+ } else {
+ /* Get the average length of all the 4 channels. */
+ agc_value /= IGP01E1000_PHY_CHANNEL_NUM;
+ }
- if (!timeout) {
- DEBUGOUT("Master requests are pending.\n");
- return -E1000_ERR_MASTER_REQUESTS_PENDING;
- }
+ /* Set the range of the calculated length. */
+ *min_length = ((e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) > 0) ?
+ (e1000_igp_cable_length_table[agc_value] -
+ IGP01E1000_AGC_RANGE) : 0;
+ *max_length = e1000_igp_cable_length_table[agc_value] +
+ IGP01E1000_AGC_RANGE;
+ }
- return E1000_SUCCESS;
+ return E1000_SUCCESS;
}
-/*******************************************************************************
- *
- * Check for EEPROM Auto Read bit done.
- *
- * hw: Struct containing variables accessed by shared code
+/**
+ * e1000_check_polarity - Check the cable polarity
+ * @hw: Struct containing variables accessed by shared code
+ * @polarity: output parameter : 0 - Polarity is not reversed
+ * 1 - Polarity is reversed.
*
- * returns: - E1000_ERR_RESET if fail to reset MAC
- * E1000_SUCCESS at any other case.
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
*
- ******************************************************************************/
-static s32 e1000_get_auto_rd_done(struct e1000_hw *hw)
+ * For phy's older than IGP, this function simply reads the polarity bit in the
+ * Phy Status register. For IGP phy's, this bit is valid only if link speed is
+ * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will
+ * return 0. If the link speed is 1000 Mbps the polarity status is in the
+ * IGP01E1000_PHY_PCS_INIT_REG.
+ */
+static s32 e1000_check_polarity(struct e1000_hw *hw,
+ e1000_rev_polarity *polarity)
{
- s32 timeout = AUTO_READ_DONE_TIMEOUT;
-
- DEBUGFUNC("e1000_get_auto_rd_done");
-
- switch (hw->mac_type) {
- default:
- msleep(5);
- break;
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- case e1000_ich8lan:
- while (timeout) {
- if (er32(EECD) & E1000_EECD_AUTO_RD)
- break;
- else msleep(1);
- timeout--;
- }
-
- if (!timeout) {
- DEBUGOUT("Auto read by HW from EEPROM has not completed.\n");
- return -E1000_ERR_RESET;
- }
- break;
- }
-
- /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high.
- * Need to wait for PHY configuration completion before accessing NVM
- * and PHY. */
- if (hw->mac_type == e1000_82573)
- msleep(25);
-
- return E1000_SUCCESS;
+ s32 ret_val;
+ u16 phy_data;
+
+ DEBUGFUNC("e1000_check_polarity");
+
+ if (hw->phy_type == e1000_phy_m88) {
+ /* return the Polarity bit in the Status register. */
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+ *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >>
+ M88E1000_PSSR_REV_POLARITY_SHIFT) ?
+ e1000_rev_polarity_reversed : e1000_rev_polarity_normal;
+
+ } else if (hw->phy_type == e1000_phy_igp) {
+ /* Read the Status register to check the speed */
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
+ * find the polarity status */
+ if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
+ IGP01E1000_PSSR_SPEED_1000MBPS) {
+
+ /* Read the GIG initialization PCS register (0x00B4) */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Check the polarity bits */
+ *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ?
+ e1000_rev_polarity_reversed :
+ e1000_rev_polarity_normal;
+ } else {
+ /* For 10 Mbps, read the polarity bit in the status register. (for
+ * 100 Mbps this bit is always 0) */
+ *polarity =
+ (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ?
+ e1000_rev_polarity_reversed :
+ e1000_rev_polarity_normal;
+ }
+ }
+ return E1000_SUCCESS;
}
-/***************************************************************************
- * Checks if the PHY configuration is done
- *
- * hw: Struct containing variables accessed by shared code
+/**
+ * e1000_check_downshift - Check if Downshift occurred
+ * @hw: Struct containing variables accessed by shared code
+ * @downshift: output parameter : 0 - No Downshift occurred.
+ * 1 - Downshift occurred.
*
- * returns: - E1000_ERR_RESET if fail to reset MAC
- * E1000_SUCCESS at any other case.
+ * returns: - E1000_ERR_XXX
+ * E1000_SUCCESS
*
- ***************************************************************************/
-static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
+ * For phy's older than IGP, this function reads the Downshift bit in the Phy
+ * Specific Status register. For IGP phy's, it reads the Downgrade bit in the
+ * Link Health register. In IGP this bit is latched high, so the driver must
+ * read it immediately after link is established.
+ */
+static s32 e1000_check_downshift(struct e1000_hw *hw)
{
- s32 timeout = PHY_CFG_TIMEOUT;
- u32 cfg_mask = E1000_EEPROM_CFG_DONE;
-
- DEBUGFUNC("e1000_get_phy_cfg_done");
-
- switch (hw->mac_type) {
- default:
- mdelay(10);
- break;
- case e1000_80003es2lan:
- /* Separate *_CFG_DONE_* bit for each port */
- if (er32(STATUS) & E1000_STATUS_FUNC_1)
- cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1;
- /* Fall Through */
- case e1000_82571:
- case e1000_82572:
- while (timeout) {
- if (er32(EEMNGCTL) & cfg_mask)
- break;
- else
- msleep(1);
- timeout--;
- }
- if (!timeout) {
- DEBUGOUT("MNG configuration cycle has not completed.\n");
- return -E1000_ERR_RESET;
- }
- break;
- }
-
- return E1000_SUCCESS;
-}
+ s32 ret_val;
+ u16 phy_data;
-/***************************************************************************
- *
- * Using the combination of SMBI and SWESMBI semaphore bits when resetting
- * adapter or Eeprom access.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
- * E1000_SUCCESS at any other case.
- *
- ***************************************************************************/
-static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
-{
- s32 timeout;
- u32 swsm;
-
- DEBUGFUNC("e1000_get_hw_eeprom_semaphore");
-
- if (!hw->eeprom_semaphore_present)
- return E1000_SUCCESS;
-
- if (hw->mac_type == e1000_80003es2lan) {
- /* Get the SW semaphore. */
- if (e1000_get_software_semaphore(hw) != E1000_SUCCESS)
- return -E1000_ERR_EEPROM;
- }
-
- /* Get the FW semaphore. */
- timeout = hw->eeprom.word_size + 1;
- while (timeout) {
- swsm = er32(SWSM);
- swsm |= E1000_SWSM_SWESMBI;
- ew32(SWSM, swsm);
- /* if we managed to set the bit we got the semaphore. */
- swsm = er32(SWSM);
- if (swsm & E1000_SWSM_SWESMBI)
- break;
-
- udelay(50);
- timeout--;
- }
-
- if (!timeout) {
- /* Release semaphores */
- e1000_put_hw_eeprom_semaphore(hw);
- DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n");
- return -E1000_ERR_EEPROM;
- }
-
- return E1000_SUCCESS;
-}
+ DEBUGFUNC("e1000_check_downshift");
-/***************************************************************************
- * This function clears HW semaphore bits.
- *
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - None.
- *
- ***************************************************************************/
-static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
-{
- u32 swsm;
+ if (hw->phy_type == e1000_phy_igp) {
+ ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
- DEBUGFUNC("e1000_put_hw_eeprom_semaphore");
+ hw->speed_downgraded =
+ (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0;
+ } else if (hw->phy_type == e1000_phy_m88) {
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
- if (!hw->eeprom_semaphore_present)
- return;
+ hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >>
+ M88E1000_PSSR_DOWNSHIFT_SHIFT;
+ }
- swsm = er32(SWSM);
- if (hw->mac_type == e1000_80003es2lan) {
- /* Release both semaphores. */
- swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
- } else
- swsm &= ~(E1000_SWSM_SWESMBI);
- ew32(SWSM, swsm);
+ return E1000_SUCCESS;
}
-/***************************************************************************
- *
- * Obtaining software semaphore bit (SMBI) before resetting PHY.
+/**
+ * e1000_config_dsp_after_link_change
+ * @hw: Struct containing variables accessed by shared code
+ * @link_up: was link up at the time this was called
*
- * hw: Struct containing variables accessed by shared code
- *
- * returns: - E1000_ERR_RESET if fail to obtain semaphore.
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
* E1000_SUCCESS at any other case.
*
- ***************************************************************************/
-static s32 e1000_get_software_semaphore(struct e1000_hw *hw)
-{
- s32 timeout = hw->eeprom.word_size + 1;
- u32 swsm;
-
- DEBUGFUNC("e1000_get_software_semaphore");
-
- if (hw->mac_type != e1000_80003es2lan) {
- return E1000_SUCCESS;
- }
-
- while (timeout) {
- swsm = er32(SWSM);
- /* If SMBI bit cleared, it is now set and we hold the semaphore */
- if (!(swsm & E1000_SWSM_SMBI))
- break;
- mdelay(1);
- timeout--;
- }
-
- if (!timeout) {
- DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
- return -E1000_ERR_RESET;
- }
-
- return E1000_SUCCESS;
-}
+ * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a
+ * gigabit link is achieved to improve link quality.
+ */
-/***************************************************************************
- *
- * Release semaphore bit (SMBI).
- *
- * hw: Struct containing variables accessed by shared code
- *
- ***************************************************************************/
-static void e1000_release_software_semaphore(struct e1000_hw *hw)
+static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
{
- u32 swsm;
-
- DEBUGFUNC("e1000_release_software_semaphore");
-
- if (hw->mac_type != e1000_80003es2lan) {
- return;
- }
+ s32 ret_val;
+ u16 phy_data, phy_saved_data, speed, duplex, i;
+ u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] =
+ { IGP01E1000_PHY_AGC_PARAM_A,
+ IGP01E1000_PHY_AGC_PARAM_B,
+ IGP01E1000_PHY_AGC_PARAM_C,
+ IGP01E1000_PHY_AGC_PARAM_D
+ };
+ u16 min_length, max_length;
+
+ DEBUGFUNC("e1000_config_dsp_after_link_change");
+
+ if (hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
+
+ if (link_up) {
+ ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex);
+ if (ret_val) {
+ DEBUGOUT("Error getting link speed and duplex\n");
+ return ret_val;
+ }
- swsm = er32(SWSM);
- /* Release the SW semaphores.*/
- swsm &= ~E1000_SWSM_SMBI;
- ew32(SWSM, swsm);
-}
+ if (speed == SPEED_1000) {
+
+ ret_val =
+ e1000_get_cable_length(hw, &min_length,
+ &max_length);
+ if (ret_val)
+ return ret_val;
+
+ if ((hw->dsp_config_state == e1000_dsp_config_enabled)
+ && min_length >= e1000_igp_cable_length_50) {
+
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val =
+ e1000_read_phy_reg(hw,
+ dsp_reg_array[i],
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &=
+ ~IGP01E1000_PHY_EDAC_MU_INDEX;
+
+ ret_val =
+ e1000_write_phy_reg(hw,
+ dsp_reg_array
+ [i], phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ hw->dsp_config_state =
+ e1000_dsp_config_activated;
+ }
+
+ if ((hw->ffe_config_state == e1000_ffe_config_enabled)
+ && (min_length < e1000_igp_cable_length_50)) {
+
+ u16 ffe_idle_err_timeout =
+ FFE_IDLE_ERR_COUNT_TIMEOUT_20;
+ u32 idle_errs = 0;
+
+ /* clear previous idle error counts */
+ ret_val =
+ e1000_read_phy_reg(hw, PHY_1000T_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ for (i = 0; i < ffe_idle_err_timeout; i++) {
+ udelay(1000);
+ ret_val =
+ e1000_read_phy_reg(hw,
+ PHY_1000T_STATUS,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ idle_errs +=
+ (phy_data &
+ SR_1000T_IDLE_ERROR_CNT);
+ if (idle_errs >
+ SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT)
+ {
+ hw->ffe_config_state =
+ e1000_ffe_config_active;
+
+ ret_val =
+ e1000_write_phy_reg(hw,
+ IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_CM_CP);
+ if (ret_val)
+ return ret_val;
+ break;
+ }
+
+ if (idle_errs)
+ ffe_idle_err_timeout =
+ FFE_IDLE_ERR_COUNT_TIMEOUT_100;
+ }
+ }
+ }
+ } else {
+ if (hw->dsp_config_state == e1000_dsp_config_activated) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val =
+ e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
+
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if (ret_val)
+ return ret_val;
+ for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
+ ret_val =
+ e1000_read_phy_reg(hw, dsp_reg_array[i],
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX;
+ phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS;
+
+ ret_val =
+ e1000_write_phy_reg(hw, dsp_reg_array[i],
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if (ret_val)
+ return ret_val;
+
+ mdelay(20);
+
+ /* Now enable the transmitter */
+ ret_val =
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
+
+ if (ret_val)
+ return ret_val;
+
+ hw->dsp_config_state = e1000_dsp_config_enabled;
+ }
-/******************************************************************************
- * Checks if PHY reset is blocked due to SOL/IDER session, for example.
- * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to
- * the caller to figure out how to deal with it.
- *
- * hw - Struct containing variables accessed by shared code
- *
- * returns: - E1000_BLK_PHY_RESET
- * E1000_SUCCESS
- *
- *****************************************************************************/
-s32 e1000_check_phy_reset_block(struct e1000_hw *hw)
-{
- u32 manc = 0;
- u32 fwsm = 0;
-
- if (hw->mac_type == e1000_ich8lan) {
- fwsm = er32(FWSM);
- return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS
- : E1000_BLK_PHY_RESET;
- }
-
- if (hw->mac_type > e1000_82547_rev_2)
- manc = er32(MANC);
- return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ?
- E1000_BLK_PHY_RESET : E1000_SUCCESS;
-}
+ if (hw->ffe_config_state == e1000_ffe_config_active) {
+ /* Save off the current value of register 0x2F5B to be restored at
+ * the end of the routines. */
+ ret_val =
+ e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
-static u8 e1000_arc_subsystem_valid(struct e1000_hw *hw)
-{
- u32 fwsm;
-
- /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC
- * may not be provided a DMA clock when no manageability features are
- * enabled. We do not want to perform any reads/writes to these registers
- * if this is the case. We read FWSM to determine the manageability mode.
- */
- switch (hw->mac_type) {
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- fwsm = er32(FWSM);
- if ((fwsm & E1000_FWSM_MODE_MASK) != 0)
- return true;
- break;
- case e1000_ich8lan:
- return true;
- default:
- break;
- }
- return false;
-}
+ if (ret_val)
+ return ret_val;
+ /* Disable the PHY transmitter */
+ ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003);
-/******************************************************************************
- * Configure PCI-Ex no-snoop
- *
- * hw - Struct containing variables accessed by shared code.
- * no_snoop - Bitmap of no-snoop events.
- *
- * returns: E1000_SUCCESS
- *
- *****************************************************************************/
-static s32 e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, u32 no_snoop)
-{
- u32 gcr_reg = 0;
+ if (ret_val)
+ return ret_val;
- DEBUGFUNC("e1000_set_pci_ex_no_snoop");
+ mdelay(20);
- if (hw->bus_type == e1000_bus_type_unknown)
- e1000_get_bus_info(hw);
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_FORCE_GIGA);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE,
+ IGP01E1000_PHY_DSP_FFE_DEFAULT);
+ if (ret_val)
+ return ret_val;
- if (hw->bus_type != e1000_bus_type_pci_express)
- return E1000_SUCCESS;
+ ret_val = e1000_write_phy_reg(hw, 0x0000,
+ IGP01E1000_IEEE_RESTART_AUTONEG);
+ if (ret_val)
+ return ret_val;
- if (no_snoop) {
- gcr_reg = er32(GCR);
- gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL);
- gcr_reg |= no_snoop;
- ew32(GCR, gcr_reg);
- }
- if (hw->mac_type == e1000_ich8lan) {
- u32 ctrl_ext;
+ mdelay(20);
- ew32(GCR, PCI_EX_82566_SNOOP_ALL);
+ /* Now enable the transmitter */
+ ret_val =
+ e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data);
- ctrl_ext = er32(CTRL_EXT);
- ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
- ew32(CTRL_EXT, ctrl_ext);
- }
+ if (ret_val)
+ return ret_val;
- return E1000_SUCCESS;
+ hw->ffe_config_state = e1000_ffe_config_enabled;
+ }
+ }
+ return E1000_SUCCESS;
}
-/***************************************************************************
+/**
+ * e1000_set_phy_mode - Set PHY to class A mode
+ * @hw: Struct containing variables accessed by shared code
*
- * Get software semaphore FLAG bit (SWFLAG).
- * SWFLAG is used to synchronize the access to all shared resource between
- * SW, FW and HW.
- *
- * hw: Struct containing variables accessed by shared code
- *
- ***************************************************************************/
-static s32 e1000_get_software_flag(struct e1000_hw *hw)
+ * Assumes the following operations will follow to enable the new class mode.
+ * 1. Do a PHY soft reset
+ * 2. Restart auto-negotiation or force link.
+ */
+static s32 e1000_set_phy_mode(struct e1000_hw *hw)
{
- s32 timeout = PHY_CFG_TIMEOUT;
- u32 extcnf_ctrl;
-
- DEBUGFUNC("e1000_get_software_flag");
-
- if (hw->mac_type == e1000_ich8lan) {
- while (timeout) {
- extcnf_ctrl = er32(EXTCNF_CTRL);
- extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG;
- ew32(EXTCNF_CTRL, extcnf_ctrl);
-
- extcnf_ctrl = er32(EXTCNF_CTRL);
- if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG)
- break;
- mdelay(1);
- timeout--;
- }
-
- if (!timeout) {
- DEBUGOUT("FW or HW locks the resource too long.\n");
- return -E1000_ERR_CONFIG;
- }
- }
-
- return E1000_SUCCESS;
+ s32 ret_val;
+ u16 eeprom_data;
+
+ DEBUGFUNC("e1000_set_phy_mode");
+
+ if ((hw->mac_type == e1000_82545_rev_3) &&
+ (hw->media_type == e1000_media_type_copper)) {
+ ret_val =
+ e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1,
+ &eeprom_data);
+ if (ret_val) {
+ return ret_val;
+ }
+
+ if ((eeprom_data != EEPROM_RESERVED_WORD) &&
+ (eeprom_data & EEPROM_PHY_CLASS_A)) {
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT,
+ 0x000B);
+ if (ret_val)
+ return ret_val;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL,
+ 0x8104);
+ if (ret_val)
+ return ret_val;
+
+ hw->phy_reset_disable = false;
+ }
+ }
+
+ return E1000_SUCCESS;
}
-/***************************************************************************
- *
- * Release software semaphore FLAG bit (SWFLAG).
- * SWFLAG is used to synchronize the access to all shared resource between
- * SW, FW and HW.
+/**
+ * e1000_set_d3_lplu_state - set d3 link power state
+ * @hw: Struct containing variables accessed by shared code
+ * @active: true to enable lplu false to disable lplu.
*
- * hw: Struct containing variables accessed by shared code
+ * This function sets the lplu state according to the active flag. When
+ * activating lplu this function also disables smart speed and vise versa.
+ * lplu will not be activated unless the device autonegotiation advertisement
+ * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
*
- ***************************************************************************/
-static void e1000_release_software_flag(struct e1000_hw *hw)
+ * returns: - E1000_ERR_PHY if fail to read/write the PHY
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
{
- u32 extcnf_ctrl;
+ s32 ret_val;
+ u16 phy_data;
+ DEBUGFUNC("e1000_set_d3_lplu_state");
+
+ if (hw->phy_type != e1000_phy_igp)
+ return E1000_SUCCESS;
+
+ /* During driver activity LPLU should not be used or it will attain link
+ * from the lowest speeds starting from 10Mbps. The capability is used for
+ * Dx transitions and states */
+ if (hw->mac_type == e1000_82541_rev_2
+ || hw->mac_type == e1000_82547_rev_2) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data);
+ if (ret_val)
+ return ret_val;
+ }
- DEBUGFUNC("e1000_release_software_flag");
+ if (!active) {
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
- if (hw->mac_type == e1000_ich8lan) {
- extcnf_ctrl= er32(EXTCNF_CTRL);
- extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
- ew32(EXTCNF_CTRL, extcnf_ctrl);
- }
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
+ * Dx states where the power conservation is most important. During
+ * driver activity we should enable SmartSpeed, so performance is
+ * maintained. */
+ if (hw->smart_speed == e1000_smart_speed_on) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ } else if (hw->smart_speed == e1000_smart_speed_off) {
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
+
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
+ } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT)
+ || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL)
+ || (hw->autoneg_advertised ==
+ AUTONEG_ADVERTISE_10_100_ALL)) {
+
+ if (hw->mac_type == e1000_82541_rev_2 ||
+ hw->mac_type == e1000_82547_rev_2) {
+ phy_data |= IGP01E1000_GMII_FLEX_SPD;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
+ phy_data);
+ if (ret_val)
+ return ret_val;
+ }
- return;
-}
+ /* When LPLU is enabled we should disable SmartSpeed */
+ ret_val =
+ e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ &phy_data);
+ if (ret_val)
+ return ret_val;
-/******************************************************************************
- * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access
- * register.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to read
- * data - word read from the EEPROM
- * words - number of words to read
- *****************************************************************************/
-static s32 e1000_read_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
-{
- s32 error = E1000_SUCCESS;
- u32 flash_bank = 0;
- u32 act_offset = 0;
- u32 bank_offset = 0;
- u16 word = 0;
- u16 i = 0;
-
- /* We need to know which is the valid flash bank. In the event
- * that we didn't allocate eeprom_shadow_ram, we may not be
- * managing flash_bank. So it cannot be trusted and needs
- * to be updated with each read.
- */
- /* Value of bit 22 corresponds to the flash bank we're on. */
- flash_bank = (er32(EECD) & E1000_EECD_SEC1VAL) ? 1 : 0;
-
- /* Adjust offset appropriately if we're on bank 1 - adjust for word size */
- bank_offset = flash_bank * (hw->flash_bank_size * 2);
-
- error = e1000_get_software_flag(hw);
- if (error != E1000_SUCCESS)
- return error;
-
- for (i = 0; i < words; i++) {
- if (hw->eeprom_shadow_ram != NULL &&
- hw->eeprom_shadow_ram[offset+i].modified) {
- data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word;
- } else {
- /* The NVM part needs a byte offset, hence * 2 */
- act_offset = bank_offset + ((offset + i) * 2);
- error = e1000_read_ich8_word(hw, act_offset, &word);
- if (error != E1000_SUCCESS)
- break;
- data[i] = word;
- }
- }
-
- e1000_release_software_flag(hw);
-
- return error;
-}
+ phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
+ ret_val =
+ e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
+ phy_data);
+ if (ret_val)
+ return ret_val;
-/******************************************************************************
- * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access
- * register. Actually, writes are written to the shadow ram cache in the hw
- * structure hw->e1000_shadow_ram. e1000_commit_shadow_ram flushes this to
- * the NVM, which occurs when the NVM checksum is updated.
- *
- * hw - Struct containing variables accessed by shared code
- * offset - offset of word in the EEPROM to write
- * words - number of words to write
- * data - words to write to the EEPROM
- *****************************************************************************/
-static s32 e1000_write_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words,
- u16 *data)
-{
- u32 i = 0;
- s32 error = E1000_SUCCESS;
-
- error = e1000_get_software_flag(hw);
- if (error != E1000_SUCCESS)
- return error;
-
- /* A driver can write to the NVM only if it has eeprom_shadow_ram
- * allocated. Subsequent reads to the modified words are read from
- * this cached structure as well. Writes will only go into this
- * cached structure unless it's followed by a call to
- * e1000_update_eeprom_checksum() where it will commit the changes
- * and clear the "modified" field.
- */
- if (hw->eeprom_shadow_ram != NULL) {
- for (i = 0; i < words; i++) {
- if ((offset + i) < E1000_SHADOW_RAM_WORDS) {
- hw->eeprom_shadow_ram[offset+i].modified = true;
- hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i];
- } else {
- error = -E1000_ERR_EEPROM;
- break;
- }
- }
- } else {
- /* Drivers have the option to not allocate eeprom_shadow_ram as long
- * as they don't perform any NVM writes. An attempt in doing so
- * will result in this error.
- */
- error = -E1000_ERR_EEPROM;
- }
-
- e1000_release_software_flag(hw);
-
- return error;
+ }
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * This function does initial flash setup so that a new read/write/erase cycle
- * can be started.
+/**
+ * e1000_set_vco_speed
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - The pointer to the hw structure
- ****************************************************************************/
-static s32 e1000_ich8_cycle_init(struct e1000_hw *hw)
+ * Change VCO speed register to improve Bit Error Rate performance of SERDES.
+ */
+static s32 e1000_set_vco_speed(struct e1000_hw *hw)
{
- union ich8_hws_flash_status hsfsts;
- s32 error = E1000_ERR_EEPROM;
- s32 i = 0;
-
- DEBUGFUNC("e1000_ich8_cycle_init");
-
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
-
- /* May be check the Flash Des Valid bit in Hw status */
- if (hsfsts.hsf_status.fldesvalid == 0) {
- DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used.");
- return error;
- }
-
- /* Clear FCERR in Hw status by writing 1 */
- /* Clear DAEL in Hw status by writing a 1 */
- hsfsts.hsf_status.flcerr = 1;
- hsfsts.hsf_status.dael = 1;
-
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval);
-
- /* Either we should have a hardware SPI cycle in progress bit to check
- * against, in order to start a new cycle or FDONE bit should be changed
- * in the hardware so that it is 1 after harware reset, which can then be
- * used as an indication whether a cycle is in progress or has been
- * completed .. we should also have some software semaphore mechanism to
- * guard FDONE or the cycle in progress bit so that two threads access to
- * those bits can be sequentiallized or a way so that 2 threads dont
- * start the cycle at the same time */
-
- if (hsfsts.hsf_status.flcinprog == 0) {
- /* There is no cycle running at present, so we can start a cycle */
- /* Begin by setting Flash Cycle Done. */
- hsfsts.hsf_status.flcdone = 1;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval);
- error = E1000_SUCCESS;
- } else {
- /* otherwise poll for sometime so the current cycle has a chance
- * to end before giving up. */
- for (i = 0; i < ICH_FLASH_COMMAND_TIMEOUT; i++) {
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcinprog == 0) {
- error = E1000_SUCCESS;
- break;
- }
- udelay(1);
- }
- if (error == E1000_SUCCESS) {
- /* Successful in waiting for previous cycle to timeout,
- * now set the Flash Cycle Done. */
- hsfsts.hsf_status.flcdone = 1;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval);
- } else {
- DEBUGOUT("Flash controller busy, cannot get access");
- }
- }
- return error;
-}
+ s32 ret_val;
+ u16 default_page = 0;
+ u16 phy_data;
-/******************************************************************************
- * This function starts a flash cycle and waits for its completion
- *
- * hw - The pointer to the hw structure
- ****************************************************************************/
-static s32 e1000_ich8_flash_cycle(struct e1000_hw *hw, u32 timeout)
-{
- union ich8_hws_flash_ctrl hsflctl;
- union ich8_hws_flash_status hsfsts;
- s32 error = E1000_ERR_EEPROM;
- u32 i = 0;
-
- /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- hsflctl.hsf_ctrl.flcgo = 1;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* wait till FDONE bit is set to 1 */
- do {
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcdone == 1)
- break;
- udelay(1);
- i++;
- } while (i < timeout);
- if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) {
- error = E1000_SUCCESS;
- }
- return error;
-}
+ DEBUGFUNC("e1000_set_vco_speed");
-/******************************************************************************
- * Reads a byte or word from the NVM using the ICH8 flash access registers.
- *
- * hw - The pointer to the hw structure
- * index - The index of the byte or word to read.
- * size - Size of data to read, 1=byte 2=word
- * data - Pointer to the word to store the value read.
- *****************************************************************************/
-static s32 e1000_read_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 *data)
-{
- union ich8_hws_flash_status hsfsts;
- union ich8_hws_flash_ctrl hsflctl;
- u32 flash_linear_address;
- u32 flash_data = 0;
- s32 error = -E1000_ERR_EEPROM;
- s32 count = 0;
-
- DEBUGFUNC("e1000_read_ich8_data");
-
- if (size < 1 || size > 2 || data == NULL ||
- index > ICH_FLASH_LINEAR_ADDR_MASK)
- return error;
-
- flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) +
- hw->flash_base_addr;
-
- do {
- udelay(1);
- /* Steps */
- error = e1000_ich8_cycle_init(hw);
- if (error != E1000_SUCCESS)
- break;
-
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
- hsflctl.hsf_ctrl.fldbcount = size - 1;
- hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* Write the last 24 bits of index into Flash Linear address field in
- * Flash Address */
- /* TODO: TBD maybe check the index against the size of flash */
-
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address);
-
- error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT);
-
- /* Check if FCERR is set to 1, if set to 1, clear it and try the whole
- * sequence a few more times, else read in (shift in) the Flash Data0,
- * the order is least significant byte first msb to lsb */
- if (error == E1000_SUCCESS) {
- flash_data = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0);
- if (size == 1) {
- *data = (u8)(flash_data & 0x000000FF);
- } else if (size == 2) {
- *data = (u16)(flash_data & 0x0000FFFF);
- }
- break;
- } else {
- /* If we've gotten here, then things are probably completely hosed,
- * but if the error condition is detected, it won't hurt to give
- * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
- */
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcerr == 1) {
- /* Repeat for some time before giving up. */
- continue;
- } else if (hsfsts.hsf_status.flcdone == 0) {
- DEBUGOUT("Timeout error - flash cycle did not complete.");
- break;
- }
- }
- } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
-
- return error;
-}
+ switch (hw->mac_type) {
+ case e1000_82545_rev_3:
+ case e1000_82546_rev_3:
+ break;
+ default:
+ return E1000_SUCCESS;
+ }
-/******************************************************************************
- * Writes One /two bytes to the NVM using the ICH8 flash access registers.
- *
- * hw - The pointer to the hw structure
- * index - The index of the byte/word to read.
- * size - Size of data to read, 1=byte 2=word
- * data - The byte(s) to write to the NVM.
- *****************************************************************************/
-static s32 e1000_write_ich8_data(struct e1000_hw *hw, u32 index, u32 size,
- u16 data)
-{
- union ich8_hws_flash_status hsfsts;
- union ich8_hws_flash_ctrl hsflctl;
- u32 flash_linear_address;
- u32 flash_data = 0;
- s32 error = -E1000_ERR_EEPROM;
- s32 count = 0;
-
- DEBUGFUNC("e1000_write_ich8_data");
-
- if (size < 1 || size > 2 || data > size * 0xff ||
- index > ICH_FLASH_LINEAR_ADDR_MASK)
- return error;
-
- flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) +
- hw->flash_base_addr;
-
- do {
- udelay(1);
- /* Steps */
- error = e1000_ich8_cycle_init(hw);
- if (error != E1000_SUCCESS)
- break;
-
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- /* 0b/1b corresponds to 1 or 2 byte size, respectively. */
- hsflctl.hsf_ctrl.fldbcount = size -1;
- hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* Write the last 24 bits of index into Flash Linear address field in
- * Flash Address */
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address);
-
- if (size == 1)
- flash_data = (u32)data & 0x00FF;
- else
- flash_data = (u32)data;
-
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data);
-
- /* check if FCERR is set to 1 , if set to 1, clear it and try the whole
- * sequence a few more times else done */
- error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT);
- if (error == E1000_SUCCESS) {
- break;
- } else {
- /* If we're here, then things are most likely completely hosed,
- * but if the error condition is detected, it won't hurt to give
- * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times.
- */
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcerr == 1) {
- /* Repeat for some time before giving up. */
- continue;
- } else if (hsfsts.hsf_status.flcdone == 0) {
- DEBUGOUT("Timeout error - flash cycle did not complete.");
- break;
- }
- }
- } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
-
- return error;
-}
+ /* Set PHY register 30, page 5, bit 8 to 0 */
-/******************************************************************************
- * Reads a single byte from the NVM using the ICH8 flash access registers.
- *
- * hw - pointer to e1000_hw structure
- * index - The index of the byte to read.
- * data - Pointer to a byte to store the value read.
- *****************************************************************************/
-static s32 e1000_read_ich8_byte(struct e1000_hw *hw, u32 index, u8 *data)
-{
- s32 status = E1000_SUCCESS;
- u16 word = 0;
+ ret_val =
+ e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page);
+ if (ret_val)
+ return ret_val;
- status = e1000_read_ich8_data(hw, index, 1, &word);
- if (status == E1000_SUCCESS) {
- *data = (u8)word;
- }
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005);
+ if (ret_val)
+ return ret_val;
- return status;
-}
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
-/******************************************************************************
- * Writes a single byte to the NVM using the ICH8 flash access registers.
- * Performs verification by reading back the value and then going through
- * a retry algorithm before giving up.
- *
- * hw - pointer to e1000_hw structure
- * index - The index of the byte to write.
- * byte - The byte to write to the NVM.
- *****************************************************************************/
-static s32 e1000_verify_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 byte)
-{
- s32 error = E1000_SUCCESS;
- s32 program_retries = 0;
+ phy_data &= ~M88E1000_PHY_VCO_REG_BIT8;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
+
+ /* Set PHY register 30, page 4, bit 11 to 1 */
- DEBUGOUT2("Byte := %2.2X Offset := %d\n", byte, index);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004);
+ if (ret_val)
+ return ret_val;
- error = e1000_write_ich8_byte(hw, index, byte);
+ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data);
+ if (ret_val)
+ return ret_val;
- if (error != E1000_SUCCESS) {
- for (program_retries = 0; program_retries < 100; program_retries++) {
- DEBUGOUT2("Retrying \t Byte := %2.2X Offset := %d\n", byte, index);
- error = e1000_write_ich8_byte(hw, index, byte);
- udelay(100);
- if (error == E1000_SUCCESS)
- break;
- }
- }
+ phy_data |= M88E1000_PHY_VCO_REG_BIT11;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data);
+ if (ret_val)
+ return ret_val;
- if (program_retries == 100)
- error = E1000_ERR_EEPROM;
+ ret_val =
+ e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page);
+ if (ret_val)
+ return ret_val;
- return error;
+ return E1000_SUCCESS;
}
-/******************************************************************************
- * Writes a single byte to the NVM using the ICH8 flash access registers.
+
+/**
+ * e1000_enable_mng_pass_thru - check for bmc pass through
+ * @hw: Struct containing variables accessed by shared code
*
- * hw - pointer to e1000_hw structure
- * index - The index of the byte to read.
- * data - The byte to write to the NVM.
- *****************************************************************************/
-static s32 e1000_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 data)
+ * Verifies the hardware needs to allow ARPs to be processed by the host
+ * returns: - true/false
+ */
+u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw)
{
- s32 status = E1000_SUCCESS;
- u16 word = (u16)data;
+ u32 manc;
- status = e1000_write_ich8_data(hw, index, 1, word);
+ if (hw->asf_firmware_present) {
+ manc = er32(MANC);
- return status;
+ if (!(manc & E1000_MANC_RCV_TCO_EN) ||
+ !(manc & E1000_MANC_EN_MAC_ADDR_FILTER))
+ return false;
+ if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN))
+ return true;
+ }
+ return false;
}
-/******************************************************************************
- * Reads a word from the NVM using the ICH8 flash access registers.
- *
- * hw - pointer to e1000_hw structure
- * index - The starting byte index of the word to read.
- * data - Pointer to a word to store the value read.
- *****************************************************************************/
-static s32 e1000_read_ich8_word(struct e1000_hw *hw, u32 index, u16 *data)
+static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw)
{
- s32 status = E1000_SUCCESS;
- status = e1000_read_ich8_data(hw, index, 2, data);
- return status;
-}
+ s32 ret_val;
+ u16 mii_status_reg;
+ u16 i;
-/******************************************************************************
- * Erases the bank specified. Each bank may be a 4, 8 or 64k block. Banks are 0
- * based.
- *
- * hw - pointer to e1000_hw structure
- * bank - 0 for first bank, 1 for second bank
- *
- * Note that this function may actually erase as much as 8 or 64 KBytes. The
- * amount of NVM used in each bank is a *minimum* of 4 KBytes, but in fact the
- * bank size may be 4, 8 or 64 KBytes
- *****************************************************************************/
-static s32 e1000_erase_ich8_4k_segment(struct e1000_hw *hw, u32 bank)
-{
- union ich8_hws_flash_status hsfsts;
- union ich8_hws_flash_ctrl hsflctl;
- u32 flash_linear_address;
- s32 count = 0;
- s32 error = E1000_ERR_EEPROM;
- s32 iteration;
- s32 sub_sector_size = 0;
- s32 bank_size;
- s32 j = 0;
- s32 error_flag = 0;
-
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
-
- /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */
- /* 00: The Hw sector is 256 bytes, hence we need to erase 16
- * consecutive sectors. The start index for the nth Hw sector can be
- * calculated as bank * 4096 + n * 256
- * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector.
- * The start index for the nth Hw sector can be calculated
- * as bank * 4096
- * 10: The HW sector is 8K bytes
- * 11: The Hw sector size is 64K bytes */
- if (hsfsts.hsf_status.berasesz == 0x0) {
- /* Hw sector size 256 */
- sub_sector_size = ICH_FLASH_SEG_SIZE_256;
- bank_size = ICH_FLASH_SECTOR_SIZE;
- iteration = ICH_FLASH_SECTOR_SIZE / ICH_FLASH_SEG_SIZE_256;
- } else if (hsfsts.hsf_status.berasesz == 0x1) {
- bank_size = ICH_FLASH_SEG_SIZE_4K;
- iteration = 1;
- } else if (hsfsts.hsf_status.berasesz == 0x3) {
- bank_size = ICH_FLASH_SEG_SIZE_64K;
- iteration = 1;
- } else {
- return error;
- }
-
- for (j = 0; j < iteration ; j++) {
- do {
- count++;
- /* Steps */
- error = e1000_ich8_cycle_init(hw);
- if (error != E1000_SUCCESS) {
- error_flag = 1;
- break;
- }
-
- /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash
- * Control */
- hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL);
- hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE;
- E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval);
-
- /* Write the last 24 bits of an index within the block into Flash
- * Linear address field in Flash Address. This probably needs to
- * be calculated here based off the on-chip erase sector size and
- * the software bank size (4, 8 or 64 KBytes) */
- flash_linear_address = bank * bank_size + j * sub_sector_size;
- flash_linear_address += hw->flash_base_addr;
- flash_linear_address &= ICH_FLASH_LINEAR_ADDR_MASK;
-
- E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address);
-
- error = e1000_ich8_flash_cycle(hw, ICH_FLASH_ERASE_TIMEOUT);
- /* Check if FCERR is set to 1. If 1, clear it and try the whole
- * sequence a few more times else Done */
- if (error == E1000_SUCCESS) {
- break;
- } else {
- hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS);
- if (hsfsts.hsf_status.flcerr == 1) {
- /* repeat for some time before giving up */
- continue;
- } else if (hsfsts.hsf_status.flcdone == 0) {
- error_flag = 1;
- break;
- }
- }
- } while ((count < ICH_FLASH_CYCLE_REPEAT_COUNT) && !error_flag);
- if (error_flag == 1)
- break;
- }
- if (error_flag != 1)
- error = E1000_SUCCESS;
- return error;
-}
+ /* Polarity reversal workaround for forced 10F/10H links. */
-static s32 e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw,
- u32 cnf_base_addr,
- u32 cnf_size)
-{
- u32 ret_val = E1000_SUCCESS;
- u16 word_addr, reg_data, reg_addr;
- u16 i;
+ /* Disable the transmitter on the PHY */
- /* cnf_base_addr is in DWORD */
- word_addr = (u16)(cnf_base_addr << 1);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if (ret_val)
+ return ret_val;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF);
+ if (ret_val)
+ return ret_val;
- /* cnf_size is returned in size of dwords */
- for (i = 0; i < cnf_size; i++) {
- ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, ®_data);
- if (ret_val)
- return ret_val;
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if (ret_val)
+ return ret_val;
- ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr);
- if (ret_val)
- return ret_val;
+ /* This loop will early-out if the NO link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be clear.
+ */
- ret_val = e1000_get_software_flag(hw);
- if (ret_val != E1000_SUCCESS)
- return ret_val;
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
- ret_val = e1000_write_phy_reg_ex(hw, (u32)reg_addr, reg_data);
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
- e1000_release_software_flag(hw);
- }
+ if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0)
+ break;
+ mdelay(100);
+ }
- return ret_val;
+ /* Recommended delay time after link has been lost */
+ mdelay(1000);
+
+ /* Now we will re-enable th transmitter on the PHY */
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00);
+ if (ret_val)
+ return ret_val;
+ mdelay(50);
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000);
+ if (ret_val)
+ return ret_val;
+
+ /* This loop will early-out if the link condition has been met. */
+ for (i = PHY_FORCE_TIME; i > 0; i--) {
+ /* Read the MII Status Register and wait for Link Status bit
+ * to be set.
+ */
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
+ if (ret_val)
+ return ret_val;
+
+ if (mii_status_reg & MII_SR_LINK_STATUS)
+ break;
+ mdelay(100);
+ }
+ return E1000_SUCCESS;
}
-
-/******************************************************************************
- * This function initializes the PHY from the NVM on ICH8 platforms. This
- * is needed due to an issue where the NVM configuration is not properly
- * autoloaded after power transitions. Therefore, after each PHY reset, we
- * will load the configuration data out of the NVM manually.
+/**
+ * e1000_get_auto_rd_done
+ * @hw: Struct containing variables accessed by shared code
*
- * hw: Struct containing variables accessed by shared code
- *****************************************************************************/
-static s32 e1000_init_lcd_from_nvm(struct e1000_hw *hw)
+ * Check for EEPROM Auto Read bit done.
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_get_auto_rd_done(struct e1000_hw *hw)
{
- u32 reg_data, cnf_base_addr, cnf_size, ret_val, loop;
-
- if (hw->phy_type != e1000_phy_igp_3)
- return E1000_SUCCESS;
-
- /* Check if SW needs configure the PHY */
- reg_data = er32(FEXTNVM);
- if (!(reg_data & FEXTNVM_SW_CONFIG))
- return E1000_SUCCESS;
-
- /* Wait for basic configuration completes before proceeding*/
- loop = 0;
- do {
- reg_data = er32(STATUS) & E1000_STATUS_LAN_INIT_DONE;
- udelay(100);
- loop++;
- } while ((!reg_data) && (loop < 50));
-
- /* Clear the Init Done bit for the next init event */
- reg_data = er32(STATUS);
- reg_data &= ~E1000_STATUS_LAN_INIT_DONE;
- ew32(STATUS, reg_data);
-
- /* Make sure HW does not configure LCD from PHY extended configuration
- before SW configuration */
- reg_data = er32(EXTCNF_CTRL);
- if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) {
- reg_data = er32(EXTCNF_SIZE);
- cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH;
- cnf_size >>= 16;
- if (cnf_size) {
- reg_data = er32(EXTCNF_CTRL);
- cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER;
- /* cnf_base_addr is in DWORD */
- cnf_base_addr >>= 16;
-
- /* Configure LCD from extended configuration region. */
- ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr,
- cnf_size);
- if (ret_val)
- return ret_val;
- }
- }
-
- return E1000_SUCCESS;
+ DEBUGFUNC("e1000_get_auto_rd_done");
+ msleep(5);
+ return E1000_SUCCESS;
}
+/**
+ * e1000_get_phy_cfg_done
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Checks if the PHY configuration is done
+ * returns: - E1000_ERR_RESET if fail to reset MAC
+ * E1000_SUCCESS at any other case.
+ */
+static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw)
+{
+ DEBUGFUNC("e1000_get_phy_cfg_done");
+ mdelay(10);
+ return E1000_SUCCESS;
+}
#include "e1000_osdep.h"
-
/* Forward declarations of structures used by the shared code */
struct e1000_hw;
struct e1000_hw_stats;
/* Enumerated types specific to the e1000 hardware */
/* Media Access Controlers */
typedef enum {
- e1000_undefined = 0,
- e1000_82542_rev2_0,
- e1000_82542_rev2_1,
- e1000_82543,
- e1000_82544,
- e1000_82540,
- e1000_82545,
- e1000_82545_rev_3,
- e1000_82546,
- e1000_82546_rev_3,
- e1000_82541,
- e1000_82541_rev_2,
- e1000_82547,
- e1000_82547_rev_2,
- e1000_82571,
- e1000_82572,
- e1000_82573,
- e1000_80003es2lan,
- e1000_ich8lan,
- e1000_num_macs
+ e1000_undefined = 0,
+ e1000_82542_rev2_0,
+ e1000_82542_rev2_1,
+ e1000_82543,
+ e1000_82544,
+ e1000_82540,
+ e1000_82545,
+ e1000_82545_rev_3,
+ e1000_82546,
+ e1000_82546_rev_3,
+ e1000_82541,
+ e1000_82541_rev_2,
+ e1000_82547,
+ e1000_82547_rev_2,
+ e1000_num_macs
} e1000_mac_type;
typedef enum {
- e1000_eeprom_uninitialized = 0,
- e1000_eeprom_spi,
- e1000_eeprom_microwire,
- e1000_eeprom_flash,
- e1000_eeprom_ich8,
- e1000_eeprom_none, /* No NVM support */
- e1000_num_eeprom_types
+ e1000_eeprom_uninitialized = 0,
+ e1000_eeprom_spi,
+ e1000_eeprom_microwire,
+ e1000_eeprom_flash,
+ e1000_eeprom_none, /* No NVM support */
+ e1000_num_eeprom_types
} e1000_eeprom_type;
/* Media Types */
typedef enum {
- e1000_media_type_copper = 0,
- e1000_media_type_fiber = 1,
- e1000_media_type_internal_serdes = 2,
- e1000_num_media_types
+ e1000_media_type_copper = 0,
+ e1000_media_type_fiber = 1,
+ e1000_media_type_internal_serdes = 2,
+ e1000_num_media_types
} e1000_media_type;
typedef enum {
- e1000_10_half = 0,
- e1000_10_full = 1,
- e1000_100_half = 2,
- e1000_100_full = 3
+ e1000_10_half = 0,
+ e1000_10_full = 1,
+ e1000_100_half = 2,
+ e1000_100_full = 3
} e1000_speed_duplex_type;
/* Flow Control Settings */
typedef enum {
- E1000_FC_NONE = 0,
- E1000_FC_RX_PAUSE = 1,
- E1000_FC_TX_PAUSE = 2,
- E1000_FC_FULL = 3,
- E1000_FC_DEFAULT = 0xFF
+ E1000_FC_NONE = 0,
+ E1000_FC_RX_PAUSE = 1,
+ E1000_FC_TX_PAUSE = 2,
+ E1000_FC_FULL = 3,
+ E1000_FC_DEFAULT = 0xFF
} e1000_fc_type;
struct e1000_shadow_ram {
- u16 eeprom_word;
- bool modified;
+ u16 eeprom_word;
+ bool modified;
};
/* PCI bus types */
typedef enum {
- e1000_bus_type_unknown = 0,
- e1000_bus_type_pci,
- e1000_bus_type_pcix,
- e1000_bus_type_pci_express,
- e1000_bus_type_reserved
+ e1000_bus_type_unknown = 0,
+ e1000_bus_type_pci,
+ e1000_bus_type_pcix,
+ e1000_bus_type_reserved
} e1000_bus_type;
/* PCI bus speeds */
typedef enum {
- e1000_bus_speed_unknown = 0,
- e1000_bus_speed_33,
- e1000_bus_speed_66,
- e1000_bus_speed_100,
- e1000_bus_speed_120,
- e1000_bus_speed_133,
- e1000_bus_speed_2500,
- e1000_bus_speed_reserved
+ e1000_bus_speed_unknown = 0,
+ e1000_bus_speed_33,
+ e1000_bus_speed_66,
+ e1000_bus_speed_100,
+ e1000_bus_speed_120,
+ e1000_bus_speed_133,
+ e1000_bus_speed_reserved
} e1000_bus_speed;
/* PCI bus widths */
typedef enum {
- e1000_bus_width_unknown = 0,
- /* These PCIe values should literally match the possible return values
- * from config space */
- e1000_bus_width_pciex_1 = 1,
- e1000_bus_width_pciex_2 = 2,
- e1000_bus_width_pciex_4 = 4,
- e1000_bus_width_32,
- e1000_bus_width_64,
- e1000_bus_width_reserved
+ e1000_bus_width_unknown = 0,
+ e1000_bus_width_32,
+ e1000_bus_width_64,
+ e1000_bus_width_reserved
} e1000_bus_width;
/* PHY status info structure and supporting enums */
typedef enum {
- e1000_cable_length_50 = 0,
- e1000_cable_length_50_80,
- e1000_cable_length_80_110,
- e1000_cable_length_110_140,
- e1000_cable_length_140,
- e1000_cable_length_undefined = 0xFF
+ e1000_cable_length_50 = 0,
+ e1000_cable_length_50_80,
+ e1000_cable_length_80_110,
+ e1000_cable_length_110_140,
+ e1000_cable_length_140,
+ e1000_cable_length_undefined = 0xFF
} e1000_cable_length;
typedef enum {
- e1000_gg_cable_length_60 = 0,
- e1000_gg_cable_length_60_115 = 1,
- e1000_gg_cable_length_115_150 = 2,
- e1000_gg_cable_length_150 = 4
+ e1000_gg_cable_length_60 = 0,
+ e1000_gg_cable_length_60_115 = 1,
+ e1000_gg_cable_length_115_150 = 2,
+ e1000_gg_cable_length_150 = 4
} e1000_gg_cable_length;
typedef enum {
- e1000_igp_cable_length_10 = 10,
- e1000_igp_cable_length_20 = 20,
- e1000_igp_cable_length_30 = 30,
- e1000_igp_cable_length_40 = 40,
- e1000_igp_cable_length_50 = 50,
- e1000_igp_cable_length_60 = 60,
- e1000_igp_cable_length_70 = 70,
- e1000_igp_cable_length_80 = 80,
- e1000_igp_cable_length_90 = 90,
- e1000_igp_cable_length_100 = 100,
- e1000_igp_cable_length_110 = 110,
- e1000_igp_cable_length_115 = 115,
- e1000_igp_cable_length_120 = 120,
- e1000_igp_cable_length_130 = 130,
- e1000_igp_cable_length_140 = 140,
- e1000_igp_cable_length_150 = 150,
- e1000_igp_cable_length_160 = 160,
- e1000_igp_cable_length_170 = 170,
- e1000_igp_cable_length_180 = 180
+ e1000_igp_cable_length_10 = 10,
+ e1000_igp_cable_length_20 = 20,
+ e1000_igp_cable_length_30 = 30,
+ e1000_igp_cable_length_40 = 40,
+ e1000_igp_cable_length_50 = 50,
+ e1000_igp_cable_length_60 = 60,
+ e1000_igp_cable_length_70 = 70,
+ e1000_igp_cable_length_80 = 80,
+ e1000_igp_cable_length_90 = 90,
+ e1000_igp_cable_length_100 = 100,
+ e1000_igp_cable_length_110 = 110,
+ e1000_igp_cable_length_115 = 115,
+ e1000_igp_cable_length_120 = 120,
+ e1000_igp_cable_length_130 = 130,
+ e1000_igp_cable_length_140 = 140,
+ e1000_igp_cable_length_150 = 150,
+ e1000_igp_cable_length_160 = 160,
+ e1000_igp_cable_length_170 = 170,
+ e1000_igp_cable_length_180 = 180
} e1000_igp_cable_length;
typedef enum {
- e1000_10bt_ext_dist_enable_normal = 0,
- e1000_10bt_ext_dist_enable_lower,
- e1000_10bt_ext_dist_enable_undefined = 0xFF
+ e1000_10bt_ext_dist_enable_normal = 0,
+ e1000_10bt_ext_dist_enable_lower,
+ e1000_10bt_ext_dist_enable_undefined = 0xFF
} e1000_10bt_ext_dist_enable;
typedef enum {
- e1000_rev_polarity_normal = 0,
- e1000_rev_polarity_reversed,
- e1000_rev_polarity_undefined = 0xFF
+ e1000_rev_polarity_normal = 0,
+ e1000_rev_polarity_reversed,
+ e1000_rev_polarity_undefined = 0xFF
} e1000_rev_polarity;
typedef enum {
- e1000_downshift_normal = 0,
- e1000_downshift_activated,
- e1000_downshift_undefined = 0xFF
+ e1000_downshift_normal = 0,
+ e1000_downshift_activated,
+ e1000_downshift_undefined = 0xFF
} e1000_downshift;
typedef enum {
- e1000_smart_speed_default = 0,
- e1000_smart_speed_on,
- e1000_smart_speed_off
+ e1000_smart_speed_default = 0,
+ e1000_smart_speed_on,
+ e1000_smart_speed_off
} e1000_smart_speed;
typedef enum {
- e1000_polarity_reversal_enabled = 0,
- e1000_polarity_reversal_disabled,
- e1000_polarity_reversal_undefined = 0xFF
+ e1000_polarity_reversal_enabled = 0,
+ e1000_polarity_reversal_disabled,
+ e1000_polarity_reversal_undefined = 0xFF
} e1000_polarity_reversal;
typedef enum {
- e1000_auto_x_mode_manual_mdi = 0,
- e1000_auto_x_mode_manual_mdix,
- e1000_auto_x_mode_auto1,
- e1000_auto_x_mode_auto2,
- e1000_auto_x_mode_undefined = 0xFF
+ e1000_auto_x_mode_manual_mdi = 0,
+ e1000_auto_x_mode_manual_mdix,
+ e1000_auto_x_mode_auto1,
+ e1000_auto_x_mode_auto2,
+ e1000_auto_x_mode_undefined = 0xFF
} e1000_auto_x_mode;
typedef enum {
- e1000_1000t_rx_status_not_ok = 0,
- e1000_1000t_rx_status_ok,
- e1000_1000t_rx_status_undefined = 0xFF
+ e1000_1000t_rx_status_not_ok = 0,
+ e1000_1000t_rx_status_ok,
+ e1000_1000t_rx_status_undefined = 0xFF
} e1000_1000t_rx_status;
typedef enum {
e1000_phy_m88 = 0,
e1000_phy_igp,
- e1000_phy_igp_2,
- e1000_phy_gg82563,
- e1000_phy_igp_3,
- e1000_phy_ife,
e1000_phy_undefined = 0xFF
} e1000_phy_type;
typedef enum {
- e1000_ms_hw_default = 0,
- e1000_ms_force_master,
- e1000_ms_force_slave,
- e1000_ms_auto
+ e1000_ms_hw_default = 0,
+ e1000_ms_force_master,
+ e1000_ms_force_slave,
+ e1000_ms_auto
} e1000_ms_type;
typedef enum {
- e1000_ffe_config_enabled = 0,
- e1000_ffe_config_active,
- e1000_ffe_config_blocked
+ e1000_ffe_config_enabled = 0,
+ e1000_ffe_config_active,
+ e1000_ffe_config_blocked
} e1000_ffe_config;
typedef enum {
- e1000_dsp_config_disabled = 0,
- e1000_dsp_config_enabled,
- e1000_dsp_config_activated,
- e1000_dsp_config_undefined = 0xFF
+ e1000_dsp_config_disabled = 0,
+ e1000_dsp_config_enabled,
+ e1000_dsp_config_activated,
+ e1000_dsp_config_undefined = 0xFF
} e1000_dsp_config;
struct e1000_phy_info {
- e1000_cable_length cable_length;
- e1000_10bt_ext_dist_enable extended_10bt_distance;
- e1000_rev_polarity cable_polarity;
- e1000_downshift downshift;
- e1000_polarity_reversal polarity_correction;
- e1000_auto_x_mode mdix_mode;
- e1000_1000t_rx_status local_rx;
- e1000_1000t_rx_status remote_rx;
+ e1000_cable_length cable_length;
+ e1000_10bt_ext_dist_enable extended_10bt_distance;
+ e1000_rev_polarity cable_polarity;
+ e1000_downshift downshift;
+ e1000_polarity_reversal polarity_correction;
+ e1000_auto_x_mode mdix_mode;
+ e1000_1000t_rx_status local_rx;
+ e1000_1000t_rx_status remote_rx;
};
struct e1000_phy_stats {
- u32 idle_errors;
- u32 receive_errors;
+ u32 idle_errors;
+ u32 receive_errors;
};
struct e1000_eeprom_info {
- e1000_eeprom_type type;
- u16 word_size;
- u16 opcode_bits;
- u16 address_bits;
- u16 delay_usec;
- u16 page_size;
- bool use_eerd;
- bool use_eewr;
+ e1000_eeprom_type type;
+ u16 word_size;
+ u16 opcode_bits;
+ u16 address_bits;
+ u16 delay_usec;
+ u16 page_size;
};
/* Flex ASF Information */
#define E1000_HOST_IF_MAX_SIZE 2048
typedef enum {
- e1000_byte_align = 0,
- e1000_word_align = 1,
- e1000_dword_align = 2
+ e1000_byte_align = 0,
+ e1000_word_align = 1,
+ e1000_dword_align = 2
} e1000_align_type;
-
-
/* Error Codes */
#define E1000_SUCCESS 0
#define E1000_ERR_EEPROM 1
#define E1000_ERR_MASTER_REQUESTS_PENDING 10
#define E1000_ERR_HOST_INTERFACE_COMMAND 11
#define E1000_BLK_PHY_RESET 12
-#define E1000_ERR_SWFW_SYNC 13
#define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \
(((_value) & 0xff00) >> 8))
s32 e1000_phy_setup_autoneg(struct e1000_hw *hw);
void e1000_config_collision_dist(struct e1000_hw *hw);
s32 e1000_check_for_link(struct e1000_hw *hw);
-s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex);
+s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 * speed, u16 * duplex);
s32 e1000_force_mac_fc(struct e1000_hw *hw);
/* PHY */
-s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data);
+s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 * phy_data);
s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 data);
s32 e1000_phy_hw_reset(struct e1000_hw *hw);
s32 e1000_phy_reset(struct e1000_hw *hw);
s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info);
s32 e1000_validate_mdi_setting(struct e1000_hw *hw);
-void e1000_phy_powerdown_workaround(struct e1000_hw *hw);
-
/* EEPROM Functions */
s32 e1000_init_eeprom_params(struct e1000_hw *hw);
u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw);
#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64
-#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */
+#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */
-#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */
-#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
-#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
+#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */
+#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */
+#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */
#define E1000_MNG_IAMT_MODE 0x3
#define E1000_MNG_ICH_IAMT_MODE 0x2
-#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
+#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */
-#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
-#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */
+#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */
+#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */
#define E1000_VFTA_ENTRY_SHIFT 0x5
#define E1000_VFTA_ENTRY_MASK 0x7F
#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
struct e1000_host_mng_command_header {
- u8 command_id;
- u8 checksum;
- u16 reserved1;
- u16 reserved2;
- u16 command_length;
+ u8 command_id;
+ u8 checksum;
+ u16 reserved1;
+ u16 reserved2;
+ u16 command_length;
};
struct e1000_host_mng_command_info {
- struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
- u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658*/
+ struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658 */
};
#ifdef __BIG_ENDIAN
-struct e1000_host_mng_dhcp_cookie{
- u32 signature;
- u16 vlan_id;
- u8 reserved0;
- u8 status;
- u32 reserved1;
- u8 checksum;
- u8 reserved3;
- u16 reserved2;
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u16 vlan_id;
+ u8 reserved0;
+ u8 status;
+ u32 reserved1;
+ u8 checksum;
+ u8 reserved3;
+ u16 reserved2;
};
#else
-struct e1000_host_mng_dhcp_cookie{
- u32 signature;
- u8 status;
- u8 reserved0;
- u16 vlan_id;
- u32 reserved1;
- u16 reserved2;
- u8 reserved3;
- u8 checksum;
+struct e1000_host_mng_dhcp_cookie {
+ u32 signature;
+ u8 status;
+ u8 reserved0;
+ u16 vlan_id;
+ u32 reserved1;
+ u16 reserved2;
+ u8 reserved3;
+ u8 checksum;
};
#endif
-s32 e1000_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer,
- u16 length);
bool e1000_check_mng_mode(struct e1000_hw *hw);
-bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
-s32 e1000_read_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 *data);
+s32 e1000_read_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data);
s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw);
s32 e1000_update_eeprom_checksum(struct e1000_hw *hw);
-s32 e1000_write_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 *data);
-s32 e1000_read_mac_addr(struct e1000_hw * hw);
+s32 e1000_write_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data);
+s32 e1000_read_mac_addr(struct e1000_hw *hw);
/* Filters (multicast, vlan, receive) */
u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 * mc_addr);
/* Everything else */
void e1000_reset_adaptive(struct e1000_hw *hw);
void e1000_update_adaptive(struct e1000_hw *hw);
-void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, u32 frame_len, u8 * mac_addr);
+void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
+ u32 frame_len, u8 * mac_addr);
void e1000_get_bus_info(struct e1000_hw *hw);
void e1000_pci_set_mwi(struct e1000_hw *hw);
void e1000_pci_clear_mwi(struct e1000_hw *hw);
-s32 e1000_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value);
void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc);
int e1000_pcix_get_mmrbc(struct e1000_hw *hw);
/* Port I/O is only supported on 82544 and newer */
void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value);
-s32 e1000_disable_pciex_master(struct e1000_hw *hw);
-s32 e1000_check_phy_reset_block(struct e1000_hw *hw);
-
#define E1000_READ_REG_IO(a, reg) \
e1000_read_reg_io((a), E1000_##reg)
#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099
#define E1000_DEV_ID_82547EI 0x1019
#define E1000_DEV_ID_82547EI_MOBILE 0x101A
-#define E1000_DEV_ID_82571EB_COPPER 0x105E
-#define E1000_DEV_ID_82571EB_FIBER 0x105F
-#define E1000_DEV_ID_82571EB_SERDES 0x1060
-#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4
-#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5
-#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5
-#define E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE 0x10BC
-#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9
-#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA
-#define E1000_DEV_ID_82572EI_COPPER 0x107D
-#define E1000_DEV_ID_82572EI_FIBER 0x107E
-#define E1000_DEV_ID_82572EI_SERDES 0x107F
-#define E1000_DEV_ID_82572EI 0x10B9
-#define E1000_DEV_ID_82573E 0x108B
-#define E1000_DEV_ID_82573E_IAMT 0x108C
-#define E1000_DEV_ID_82573L 0x109A
#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5
-#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096
-#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098
-#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA
-#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB
-
-#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049
-#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A
-#define E1000_DEV_ID_ICH8_IGP_C 0x104B
-#define E1000_DEV_ID_ICH8_IFE 0x104C
-#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4
-#define E1000_DEV_ID_ICH8_IFE_G 0x10C5
-#define E1000_DEV_ID_ICH8_IGP_M 0x104D
-
#define NODE_ADDRESS_SIZE 6
#define ETH_LENGTH_OF_ADDRESS 6
/* The sizes (in bytes) of a ethernet packet */
#define ENET_HEADER_SIZE 14
-#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */
+#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */
#define ETHERNET_FCS_SIZE 4
#define MINIMUM_ETHERNET_PACKET_SIZE \
(MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE)
#define CRC_LENGTH ETHERNET_FCS_SIZE
#define MAX_JUMBO_FRAME_SIZE 0x3F00
-
/* 802.1q VLAN Packet Sizes */
-#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */
+#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */
/* Ethertype field values */
-#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
-#define ETHERNET_IP_TYPE 0x0800 /* IP packets */
-#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */
+#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
+#define ETHERNET_IP_TYPE 0x0800 /* IP packets */
+#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */
/* Packet Header defines */
#define IP_PROTOCOL_TCP 6
E1000_IMS_RXSEQ | \
E1000_IMS_LSC)
-/* Additional interrupts need to be handled for e1000_ich8lan:
- DSW = The FW changed the status of the DISSW bit in FWSM
- PHYINT = The LAN connected device generates an interrupt
- EPRST = Manageability reset event */
-#define IMS_ICH8LAN_ENABLE_MASK (\
- E1000_IMS_DSW | \
- E1000_IMS_PHYINT | \
- E1000_IMS_EPRST)
-
/* Number of high/low register pairs in the RAR. The RAR (Receive Address
* Registers) holds the directed and multicast addresses that we monitor. We
* reserve one of these spots for our directed address, allowing us room for
*/
#define E1000_RAR_ENTRIES 15
-#define E1000_RAR_ENTRIES_ICH8LAN 6
-
#define MIN_NUMBER_OF_DESCRIPTORS 8
#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8
/* Receive Descriptor */
struct e1000_rx_desc {
- __le64 buffer_addr; /* Address of the descriptor's data buffer */
- __le16 length; /* Length of data DMAed into data buffer */
- __le16 csum; /* Packet checksum */
- u8 status; /* Descriptor status */
- u8 errors; /* Descriptor Errors */
- __le16 special;
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ __le16 length; /* Length of data DMAed into data buffer */
+ __le16 csum; /* Packet checksum */
+ u8 status; /* Descriptor status */
+ u8 errors; /* Descriptor Errors */
+ __le16 special;
};
/* Receive Descriptor - Extended */
union e1000_rx_desc_extended {
- struct {
- __le64 buffer_addr;
- __le64 reserved;
- } read;
- struct {
- struct {
- __le32 mrq; /* Multiple Rx Queues */
- union {
- __le32 rss; /* RSS Hash */
- struct {
- __le16 ip_id; /* IP id */
- __le16 csum; /* Packet Checksum */
- } csum_ip;
- } hi_dword;
- } lower;
- struct {
- __le32 status_error; /* ext status/error */
- __le16 length;
- __le16 vlan; /* VLAN tag */
- } upper;
- } wb; /* writeback */
+ struct {
+ __le64 buffer_addr;
+ __le64 reserved;
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length;
+ __le16 vlan; /* VLAN tag */
+ } upper;
+ } wb; /* writeback */
};
#define MAX_PS_BUFFERS 4
/* Receive Descriptor - Packet Split */
union e1000_rx_desc_packet_split {
- struct {
- /* one buffer for protocol header(s), three data buffers */
- __le64 buffer_addr[MAX_PS_BUFFERS];
- } read;
- struct {
- struct {
- __le32 mrq; /* Multiple Rx Queues */
- union {
- __le32 rss; /* RSS Hash */
- struct {
- __le16 ip_id; /* IP id */
- __le16 csum; /* Packet Checksum */
- } csum_ip;
- } hi_dword;
- } lower;
- struct {
- __le32 status_error; /* ext status/error */
- __le16 length0; /* length of buffer 0 */
- __le16 vlan; /* VLAN tag */
- } middle;
- struct {
- __le16 header_status;
- __le16 length[3]; /* length of buffers 1-3 */
- } upper;
- __le64 reserved;
- } wb; /* writeback */
+ struct {
+ /* one buffer for protocol header(s), three data buffers */
+ __le64 buffer_addr[MAX_PS_BUFFERS];
+ } read;
+ struct {
+ struct {
+ __le32 mrq; /* Multiple Rx Queues */
+ union {
+ __le32 rss; /* RSS Hash */
+ struct {
+ __le16 ip_id; /* IP id */
+ __le16 csum; /* Packet Checksum */
+ } csum_ip;
+ } hi_dword;
+ } lower;
+ struct {
+ __le32 status_error; /* ext status/error */
+ __le16 length0; /* length of buffer 0 */
+ __le16 vlan; /* VLAN tag */
+ } middle;
+ struct {
+ __le16 header_status;
+ __le16 length[3]; /* length of buffers 1-3 */
+ } upper;
+ __le64 reserved;
+ } wb; /* writeback */
};
-/* Receive Decriptor bit definitions */
-#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
-#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
-#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
-#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
-#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */
-#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
-#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
-#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
-#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */
-#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */
-#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */
-#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
-#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
-#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
-#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
-#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
-#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
-#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
-#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
-#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
+/* Receive Descriptor bit definitions */
+#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
+#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
+#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
+#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
+#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
+#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */
+#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */
+#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */
+#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */
+#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */
+#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
+#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
+#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
+#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
+#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
+#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
+#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
+#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
+#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */
#define E1000_RXD_SPC_PRI_SHIFT 13
-#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
+#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */
#define E1000_RXD_SPC_CFI_SHIFT 12
#define E1000_RXDEXT_STATERR_CE 0x01000000
E1000_RXD_ERR_CXE | \
E1000_RXD_ERR_RXE)
-
/* Same mask, but for extended and packet split descriptors */
#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
E1000_RXDEXT_STATERR_CE | \
E1000_RXDEXT_STATERR_CXE | \
E1000_RXDEXT_STATERR_RXE)
-
/* Transmit Descriptor */
struct e1000_tx_desc {
- __le64 buffer_addr; /* Address of the descriptor's data buffer */
- union {
- __le32 data;
- struct {
- __le16 length; /* Data buffer length */
- u8 cso; /* Checksum offset */
- u8 cmd; /* Descriptor control */
- } flags;
- } lower;
- union {
- __le32 data;
- struct {
- u8 status; /* Descriptor status */
- u8 css; /* Checksum start */
- __le16 special;
- } fields;
- } upper;
+ __le64 buffer_addr; /* Address of the descriptor's data buffer */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 cso; /* Checksum offset */
+ u8 cmd; /* Descriptor control */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 css; /* Checksum start */
+ __le16 special;
+ } fields;
+ } upper;
};
/* Transmit Descriptor bit definitions */
-#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
-#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */
-#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
-#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
-#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
-#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
-#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
-#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
-#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
-#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
-#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
-#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
-#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
-#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
-#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
-#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
-#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
-#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
-#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
-#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
+#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
+#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */
+#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
+#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
+#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
+#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
+#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
+#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
+#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
+#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
+#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
+#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
+#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
+#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
+#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
+#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
+#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
+#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
+#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
+#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
/* Offload Context Descriptor */
struct e1000_context_desc {
- union {
- __le32 ip_config;
- struct {
- u8 ipcss; /* IP checksum start */
- u8 ipcso; /* IP checksum offset */
- __le16 ipcse; /* IP checksum end */
- } ip_fields;
- } lower_setup;
- union {
- __le32 tcp_config;
- struct {
- u8 tucss; /* TCP checksum start */
- u8 tucso; /* TCP checksum offset */
- __le16 tucse; /* TCP checksum end */
- } tcp_fields;
- } upper_setup;
- __le32 cmd_and_length; /* */
- union {
- __le32 data;
- struct {
- u8 status; /* Descriptor status */
- u8 hdr_len; /* Header length */
- __le16 mss; /* Maximum segment size */
- } fields;
- } tcp_seg_setup;
+ union {
+ __le32 ip_config;
+ struct {
+ u8 ipcss; /* IP checksum start */
+ u8 ipcso; /* IP checksum offset */
+ __le16 ipcse; /* IP checksum end */
+ } ip_fields;
+ } lower_setup;
+ union {
+ __le32 tcp_config;
+ struct {
+ u8 tucss; /* TCP checksum start */
+ u8 tucso; /* TCP checksum offset */
+ __le16 tucse; /* TCP checksum end */
+ } tcp_fields;
+ } upper_setup;
+ __le32 cmd_and_length; /* */
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 hdr_len; /* Header length */
+ __le16 mss; /* Maximum segment size */
+ } fields;
+ } tcp_seg_setup;
};
/* Offload data descriptor */
struct e1000_data_desc {
- __le64 buffer_addr; /* Address of the descriptor's buffer address */
- union {
- __le32 data;
- struct {
- __le16 length; /* Data buffer length */
- u8 typ_len_ext; /* */
- u8 cmd; /* */
- } flags;
- } lower;
- union {
- __le32 data;
- struct {
- u8 status; /* Descriptor status */
- u8 popts; /* Packet Options */
- __le16 special; /* */
- } fields;
- } upper;
+ __le64 buffer_addr; /* Address of the descriptor's buffer address */
+ union {
+ __le32 data;
+ struct {
+ __le16 length; /* Data buffer length */
+ u8 typ_len_ext; /* */
+ u8 cmd; /* */
+ } flags;
+ } lower;
+ union {
+ __le32 data;
+ struct {
+ u8 status; /* Descriptor status */
+ u8 popts; /* Packet Options */
+ __le16 special; /* */
+ } fields;
+ } upper;
};
/* Filters */
-#define E1000_NUM_UNICAST 16 /* Unicast filter entries */
-#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
-#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
-
-#define E1000_NUM_UNICAST_ICH8LAN 7
-#define E1000_MC_TBL_SIZE_ICH8LAN 32
-
+#define E1000_NUM_UNICAST 16 /* Unicast filter entries */
+#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */
+#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
/* Receive Address Register */
struct e1000_rar {
- volatile __le32 low; /* receive address low */
- volatile __le32 high; /* receive address high */
+ volatile __le32 low; /* receive address low */
+ volatile __le32 high; /* receive address high */
};
/* Number of entries in the Multicast Table Array (MTA). */
#define E1000_NUM_MTA_REGISTERS 128
-#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32
/* IPv4 Address Table Entry */
struct e1000_ipv4_at_entry {
- volatile u32 ipv4_addr; /* IP Address (RW) */
- volatile u32 reserved;
+ volatile u32 ipv4_addr; /* IP Address (RW) */
+ volatile u32 reserved;
};
/* Four wakeup IP addresses are supported */
#define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4
#define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX
-#define E1000_IP4AT_SIZE_ICH8LAN 3
#define E1000_IP6AT_SIZE 1
/* IPv6 Address Table Entry */
struct e1000_ipv6_at_entry {
- volatile u8 ipv6_addr[16];
+ volatile u8 ipv6_addr[16];
};
/* Flexible Filter Length Table Entry */
struct e1000_fflt_entry {
- volatile u32 length; /* Flexible Filter Length (RW) */
- volatile u32 reserved;
+ volatile u32 length; /* Flexible Filter Length (RW) */
+ volatile u32 reserved;
};
/* Flexible Filter Mask Table Entry */
struct e1000_ffmt_entry {
- volatile u32 mask; /* Flexible Filter Mask (RW) */
- volatile u32 reserved;
+ volatile u32 mask; /* Flexible Filter Mask (RW) */
+ volatile u32 reserved;
};
/* Flexible Filter Value Table Entry */
struct e1000_ffvt_entry {
- volatile u32 value; /* Flexible Filter Value (RW) */
- volatile u32 reserved;
+ volatile u32 value; /* Flexible Filter Value (RW) */
+ volatile u32 reserved;
};
/* Four Flexible Filters are supported */
* R/clr - register is read only and is cleared when read
* A - register array
*/
-#define E1000_CTRL 0x00000 /* Device Control - RW */
-#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */
-#define E1000_STATUS 0x00008 /* Device Status - RO */
-#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
-#define E1000_EERD 0x00014 /* EEPROM Read - RW */
-#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
-#define E1000_FLA 0x0001C /* Flash Access - RW */
-#define E1000_MDIC 0x00020 /* MDI Control - RW */
-#define E1000_SCTL 0x00024 /* SerDes Control - RW */
-#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */
-#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
-#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
-#define E1000_FCT 0x00030 /* Flow Control Type - RW */
-#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
-#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
-#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */
-#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
-#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
-#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
-#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
-#define E1000_RCTL 0x00100 /* RX Control - RW */
-#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */
-#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */
-#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */
-#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */
-#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */
-#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */
-#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
-#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */
-#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */
-#define E1000_TCTL 0x00400 /* TX Control - RW */
-#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */
-#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */
-#define E1000_TBT 0x00448 /* TX Burst Timer - RW */
-#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
-#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
-#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
-#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
-#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
+#define E1000_CTRL 0x00000 /* Device Control - RW */
+#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */
+#define E1000_STATUS 0x00008 /* Device Status - RO */
+#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */
+#define E1000_EERD 0x00014 /* EEPROM Read - RW */
+#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */
+#define E1000_FLA 0x0001C /* Flash Access - RW */
+#define E1000_MDIC 0x00020 /* MDI Control - RW */
+#define E1000_SCTL 0x00024 /* SerDes Control - RW */
+#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */
+#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */
+#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */
+#define E1000_FCT 0x00030 /* Flow Control Type - RW */
+#define E1000_VET 0x00038 /* VLAN Ether Type - RW */
+#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */
+#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */
+#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */
+#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */
+#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */
+#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */
+#define E1000_RCTL 0x00100 /* RX Control - RW */
+#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */
+#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */
+#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */
+#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */
+#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */
+#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */
+#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */
+#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */
+#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */
+#define E1000_TCTL 0x00400 /* TX Control - RW */
+#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */
+#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */
+#define E1000_TBT 0x00448 /* TX Burst Timer - RW */
+#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */
+#define E1000_LEDCTL 0x00E00 /* LED Control - RW */
+#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */
+#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */
+#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */
#define FEXTNVM_SW_CONFIG 0x0001
-#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
-#define E1000_PBS 0x01008 /* Packet Buffer Size */
-#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
+#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */
+#define E1000_PBS 0x01008 /* Packet Buffer Size */
+#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */
#define E1000_FLASH_UPDATES 1000
-#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
-#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
-#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
-#define E1000_FLSWCTL 0x01030 /* FLASH control register */
-#define E1000_FLSWDATA 0x01034 /* FLASH data register */
-#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
-#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
-#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
-#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
-#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
-#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */
-#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */
-#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */
-#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */
-#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */
-#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */
-#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */
-#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */
-#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */
-#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */
-#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */
-#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */
-#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */
-#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */
-#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */
-#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
-#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
-#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
-#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
-#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */
-#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
-#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
-#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */
-#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */
-#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */
-#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */
-#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */
-#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */
-#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */
-#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */
-#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */
-#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */
-#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */
-#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
-#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */
-#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */
-#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */
-#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */
-#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */
-#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */
-#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */
-#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */
-#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
-#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
-#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
-#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */
-#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */
-#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */
-#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */
-#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */
-#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */
-#define E1000_COLC 0x04028 /* Collision Count - R/clr */
-#define E1000_DC 0x04030 /* Defer Count - R/clr */
-#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */
-#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */
-#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */
-#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */
-#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */
-#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */
-#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */
-#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */
-#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */
-#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */
-#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */
-#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */
-#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */
-#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */
-#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */
-#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */
-#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */
-#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */
-#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */
-#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */
-#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */
-#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */
-#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */
-#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */
-#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */
-#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */
-#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */
-#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */
-#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */
-#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */
-#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */
-#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */
-#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */
-#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */
-#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */
-#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */
-#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */
-#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */
-#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */
-#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */
-#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */
-#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */
-#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */
-#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */
-#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */
-#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */
-#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */
-#define E1000_IAC 0x04100 /* Interrupt Assertion Count */
-#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */
-#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */
-#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */
-#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */
-#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */
-#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */
-#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */
-#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */
-#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */
-#define E1000_RFCTL 0x05008 /* Receive Filter Control*/
-#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
-#define E1000_RA 0x05400 /* Receive Address - RW Array */
-#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
-#define E1000_WUC 0x05800 /* Wakeup Control - RW */
-#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */
-#define E1000_WUS 0x05810 /* Wakeup Status - RO */
-#define E1000_MANC 0x05820 /* Management Control - RW */
-#define E1000_IPAV 0x05838 /* IP Address Valid - RW */
-#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */
-#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */
-#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */
-#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */
-#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */
-#define E1000_HOST_IF 0x08800 /* Host Interface */
-#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
-#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
-
-#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */
-#define E1000_MDPHYA 0x0003C /* PHY address - RW */
-#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */
-#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
-
-#define E1000_GCR 0x05B00 /* PCI-Ex Control */
-#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
-#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
-#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
-#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
-#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
-#define E1000_SWSM 0x05B50 /* SW Semaphore */
-#define E1000_FWSM 0x05B54 /* FW Semaphore */
-#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
-#define E1000_HICR 0x08F00 /* Host Inteface Control */
+#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */
+#define E1000_FLASHT 0x01028 /* FLASH Timer Register */
+#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */
+#define E1000_FLSWCTL 0x01030 /* FLASH control register */
+#define E1000_FLSWDATA 0x01034 /* FLASH data register */
+#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */
+#define E1000_FLOP 0x0103C /* FLASH Opcode Register */
+#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */
+#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */
+#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */
+#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */
+#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */
+#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */
+#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */
+#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */
+#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */
+#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */
+#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */
+#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */
+#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */
+#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */
+#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */
+#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */
+#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */
+#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */
+#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */
+#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */
+#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */
+#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */
+#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */
+#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */
+#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */
+#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */
+#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */
+#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */
+#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */
+#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */
+#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */
+#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */
+#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */
+#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */
+#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */
+#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */
+#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */
+#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */
+#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */
+#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */
+#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */
+#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */
+#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */
+#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */
+#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */
+#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */
+#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */
+#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */
+#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */
+#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */
+#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */
+#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */
+#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */
+#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */
+#define E1000_COLC 0x04028 /* Collision Count - R/clr */
+#define E1000_DC 0x04030 /* Defer Count - R/clr */
+#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */
+#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */
+#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */
+#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */
+#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */
+#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */
+#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */
+#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */
+#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */
+#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */
+#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */
+#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */
+#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */
+#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */
+#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */
+#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */
+#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */
+#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */
+#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */
+#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */
+#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */
+#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */
+#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */
+#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */
+#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */
+#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */
+#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */
+#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */
+#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */
+#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */
+#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */
+#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */
+#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */
+#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */
+#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */
+#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */
+#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */
+#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */
+#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */
+#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */
+#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */
+#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */
+#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */
+#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */
+#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */
+#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */
+#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */
+#define E1000_IAC 0x04100 /* Interrupt Assertion Count */
+#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */
+#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */
+#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */
+#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */
+#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */
+#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */
+#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */
+#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */
+#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */
+#define E1000_RFCTL 0x05008 /* Receive Filter Control */
+#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */
+#define E1000_RA 0x05400 /* Receive Address - RW Array */
+#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */
+#define E1000_WUC 0x05800 /* Wakeup Control - RW */
+#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */
+#define E1000_WUS 0x05810 /* Wakeup Status - RO */
+#define E1000_MANC 0x05820 /* Management Control - RW */
+#define E1000_IPAV 0x05838 /* IP Address Valid - RW */
+#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */
+#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */
+#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */
+#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */
+#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */
+#define E1000_HOST_IF 0x08800 /* Host Interface */
+#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */
+#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */
+
+#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */
+#define E1000_MDPHYA 0x0003C /* PHY address - RW */
+#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */
+#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
+
+#define E1000_GCR 0x05B00 /* PCI-Ex Control */
+#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */
+#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */
+#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */
+#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */
+#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */
+#define E1000_SWSM 0x05B50 /* SW Semaphore */
+#define E1000_FWSM 0x05B54 /* FW Semaphore */
+#define E1000_FFLT_DBG 0x05F04 /* Debug Register */
+#define E1000_HICR 0x08F00 /* Host Interface Control */
/* RSS registers */
-#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */
-#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */
-#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */
-#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */
-#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */
-#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */
+#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */
+#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */
+#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */
+#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */
+#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */
+#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */
/* Register Set (82542)
*
* Some of the 82542 registers are located at different offsets than they are
#define E1000_82542_RDLEN0 E1000_82542_RDLEN
#define E1000_82542_RDH0 E1000_82542_RDH
#define E1000_82542_RDT0 E1000_82542_RDT
-#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication
- * RX Control - RW */
+#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication
+ * RX Control - RW */
#define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8))
-#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */
-#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */
-#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */
-#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */
-#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */
-#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */
-#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */
-#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */
-#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */
-#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */
+#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */
+#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */
+#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */
+#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */
+#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */
+#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */
+#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */
+#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */
+#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */
+#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */
#define E1000_82542_RDTR1 0x00130
#define E1000_82542_RDBAL1 0x00138
#define E1000_82542_RDBAH1 0x0013C
#define E1000_82542_RSSIR E1000_RSSIR
#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA
#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC
-#define E1000_82542_MANC2H E1000_MANC2H
/* Statistics counters collected by the MAC */
struct e1000_hw_stats {
- u64 crcerrs;
- u64 algnerrc;
- u64 symerrs;
- u64 rxerrc;
- u64 txerrc;
- u64 mpc;
- u64 scc;
- u64 ecol;
- u64 mcc;
- u64 latecol;
- u64 colc;
- u64 dc;
- u64 tncrs;
- u64 sec;
- u64 cexterr;
- u64 rlec;
- u64 xonrxc;
- u64 xontxc;
- u64 xoffrxc;
- u64 xofftxc;
- u64 fcruc;
- u64 prc64;
- u64 prc127;
- u64 prc255;
- u64 prc511;
- u64 prc1023;
- u64 prc1522;
- u64 gprc;
- u64 bprc;
- u64 mprc;
- u64 gptc;
- u64 gorcl;
- u64 gorch;
- u64 gotcl;
- u64 gotch;
- u64 rnbc;
- u64 ruc;
- u64 rfc;
- u64 roc;
- u64 rlerrc;
- u64 rjc;
- u64 mgprc;
- u64 mgpdc;
- u64 mgptc;
- u64 torl;
- u64 torh;
- u64 totl;
- u64 toth;
- u64 tpr;
- u64 tpt;
- u64 ptc64;
- u64 ptc127;
- u64 ptc255;
- u64 ptc511;
- u64 ptc1023;
- u64 ptc1522;
- u64 mptc;
- u64 bptc;
- u64 tsctc;
- u64 tsctfc;
- u64 iac;
- u64 icrxptc;
- u64 icrxatc;
- u64 ictxptc;
- u64 ictxatc;
- u64 ictxqec;
- u64 ictxqmtc;
- u64 icrxdmtc;
- u64 icrxoc;
+ u64 crcerrs;
+ u64 algnerrc;
+ u64 symerrs;
+ u64 rxerrc;
+ u64 txerrc;
+ u64 mpc;
+ u64 scc;
+ u64 ecol;
+ u64 mcc;
+ u64 latecol;
+ u64 colc;
+ u64 dc;
+ u64 tncrs;
+ u64 sec;
+ u64 cexterr;
+ u64 rlec;
+ u64 xonrxc;
+ u64 xontxc;
+ u64 xoffrxc;
+ u64 xofftxc;
+ u64 fcruc;
+ u64 prc64;
+ u64 prc127;
+ u64 prc255;
+ u64 prc511;
+ u64 prc1023;
+ u64 prc1522;
+ u64 gprc;
+ u64 bprc;
+ u64 mprc;
+ u64 gptc;
+ u64 gorcl;
+ u64 gorch;
+ u64 gotcl;
+ u64 gotch;
+ u64 rnbc;
+ u64 ruc;
+ u64 rfc;
+ u64 roc;
+ u64 rlerrc;
+ u64 rjc;
+ u64 mgprc;
+ u64 mgpdc;
+ u64 mgptc;
+ u64 torl;
+ u64 torh;
+ u64 totl;
+ u64 toth;
+ u64 tpr;
+ u64 tpt;
+ u64 ptc64;
+ u64 ptc127;
+ u64 ptc255;
+ u64 ptc511;
+ u64 ptc1023;
+ u64 ptc1522;
+ u64 mptc;
+ u64 bptc;
+ u64 tsctc;
+ u64 tsctfc;
+ u64 iac;
+ u64 icrxptc;
+ u64 icrxatc;
+ u64 ictxptc;
+ u64 ictxatc;
+ u64 ictxqec;
+ u64 ictxqmtc;
+ u64 icrxdmtc;
+ u64 icrxoc;
};
/* Structure containing variables used by the shared code (e1000_hw.c) */
struct e1000_hw {
- u8 __iomem *hw_addr;
- u8 __iomem *flash_address;
- e1000_mac_type mac_type;
- e1000_phy_type phy_type;
- u32 phy_init_script;
- e1000_media_type media_type;
- void *back;
- struct e1000_shadow_ram *eeprom_shadow_ram;
- u32 flash_bank_size;
- u32 flash_base_addr;
- e1000_fc_type fc;
- e1000_bus_speed bus_speed;
- e1000_bus_width bus_width;
- e1000_bus_type bus_type;
+ u8 __iomem *hw_addr;
+ u8 __iomem *flash_address;
+ e1000_mac_type mac_type;
+ e1000_phy_type phy_type;
+ u32 phy_init_script;
+ e1000_media_type media_type;
+ void *back;
+ struct e1000_shadow_ram *eeprom_shadow_ram;
+ u32 flash_bank_size;
+ u32 flash_base_addr;
+ e1000_fc_type fc;
+ e1000_bus_speed bus_speed;
+ e1000_bus_width bus_width;
+ e1000_bus_type bus_type;
struct e1000_eeprom_info eeprom;
- e1000_ms_type master_slave;
- e1000_ms_type original_master_slave;
- e1000_ffe_config ffe_config_state;
- u32 asf_firmware_present;
- u32 eeprom_semaphore_present;
- u32 swfw_sync_present;
- u32 swfwhw_semaphore_present;
- unsigned long io_base;
- u32 phy_id;
- u32 phy_revision;
- u32 phy_addr;
- u32 original_fc;
- u32 txcw;
- u32 autoneg_failed;
- u32 max_frame_size;
- u32 min_frame_size;
- u32 mc_filter_type;
- u32 num_mc_addrs;
- u32 collision_delta;
- u32 tx_packet_delta;
- u32 ledctl_default;
- u32 ledctl_mode1;
- u32 ledctl_mode2;
- bool tx_pkt_filtering;
+ e1000_ms_type master_slave;
+ e1000_ms_type original_master_slave;
+ e1000_ffe_config ffe_config_state;
+ u32 asf_firmware_present;
+ u32 eeprom_semaphore_present;
+ unsigned long io_base;
+ u32 phy_id;
+ u32 phy_revision;
+ u32 phy_addr;
+ u32 original_fc;
+ u32 txcw;
+ u32 autoneg_failed;
+ u32 max_frame_size;
+ u32 min_frame_size;
+ u32 mc_filter_type;
+ u32 num_mc_addrs;
+ u32 collision_delta;
+ u32 tx_packet_delta;
+ u32 ledctl_default;
+ u32 ledctl_mode1;
+ u32 ledctl_mode2;
+ bool tx_pkt_filtering;
struct e1000_host_mng_dhcp_cookie mng_cookie;
- u16 phy_spd_default;
- u16 autoneg_advertised;
- u16 pci_cmd_word;
- u16 fc_high_water;
- u16 fc_low_water;
- u16 fc_pause_time;
- u16 current_ifs_val;
- u16 ifs_min_val;
- u16 ifs_max_val;
- u16 ifs_step_size;
- u16 ifs_ratio;
- u16 device_id;
- u16 vendor_id;
- u16 subsystem_id;
- u16 subsystem_vendor_id;
- u8 revision_id;
- u8 autoneg;
- u8 mdix;
- u8 forced_speed_duplex;
- u8 wait_autoneg_complete;
- u8 dma_fairness;
- u8 mac_addr[NODE_ADDRESS_SIZE];
- u8 perm_mac_addr[NODE_ADDRESS_SIZE];
- bool disable_polarity_correction;
- bool speed_downgraded;
- e1000_smart_speed smart_speed;
- e1000_dsp_config dsp_config_state;
- bool get_link_status;
- bool serdes_link_down;
- bool tbi_compatibility_en;
- bool tbi_compatibility_on;
- bool laa_is_present;
- bool phy_reset_disable;
- bool initialize_hw_bits_disable;
- bool fc_send_xon;
- bool fc_strict_ieee;
- bool report_tx_early;
- bool adaptive_ifs;
- bool ifs_params_forced;
- bool in_ifs_mode;
- bool mng_reg_access_disabled;
- bool leave_av_bit_off;
- bool kmrn_lock_loss_workaround_disabled;
- bool bad_tx_carr_stats_fd;
- bool has_manc2h;
- bool rx_needs_kicking;
- bool has_smbus;
+ u16 phy_spd_default;
+ u16 autoneg_advertised;
+ u16 pci_cmd_word;
+ u16 fc_high_water;
+ u16 fc_low_water;
+ u16 fc_pause_time;
+ u16 current_ifs_val;
+ u16 ifs_min_val;
+ u16 ifs_max_val;
+ u16 ifs_step_size;
+ u16 ifs_ratio;
+ u16 device_id;
+ u16 vendor_id;
+ u16 subsystem_id;
+ u16 subsystem_vendor_id;
+ u8 revision_id;
+ u8 autoneg;
+ u8 mdix;
+ u8 forced_speed_duplex;
+ u8 wait_autoneg_complete;
+ u8 dma_fairness;
+ u8 mac_addr[NODE_ADDRESS_SIZE];
+ u8 perm_mac_addr[NODE_ADDRESS_SIZE];
+ bool disable_polarity_correction;
+ bool speed_downgraded;
+ e1000_smart_speed smart_speed;
+ e1000_dsp_config dsp_config_state;
+ bool get_link_status;
+ bool serdes_has_link;
+ bool tbi_compatibility_en;
+ bool tbi_compatibility_on;
+ bool laa_is_present;
+ bool phy_reset_disable;
+ bool initialize_hw_bits_disable;
+ bool fc_send_xon;
+ bool fc_strict_ieee;
+ bool report_tx_early;
+ bool adaptive_ifs;
+ bool ifs_params_forced;
+ bool in_ifs_mode;
+ bool mng_reg_access_disabled;
+ bool leave_av_bit_off;
+ bool bad_tx_carr_stats_fd;
+ bool has_smbus;
};
-
-#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */
-#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */
-#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */
-#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
-#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */
-#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
-#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */
-#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */
+#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */
+#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */
+#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */
+#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
+#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */
+#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
+#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */
+#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */
/* Register Bit Masks */
/* Device Control */
-#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
-#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
-#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
-#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
-#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
-#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
-#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
-#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
-#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
-#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
-#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
-#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
-#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
-#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
-#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
-#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
-#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
-#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */
-#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */
-#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */
-#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */
-#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
-#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
-#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
-#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
-#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
-#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */
-#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
-#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
-#define E1000_CTRL_RST 0x04000000 /* Global reset */
-#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
-#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
-#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
-#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
-#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
-#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */
+#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
+#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */
+#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */
+#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
+#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
+#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */
+#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */
+#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
+#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
+#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
+#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
+#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
+#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
+#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
+#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */
+#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
+#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
+#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */
+#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */
+#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */
+#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */
+#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
+#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
+#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
+#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
+#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
+#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */
+#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
+#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
+#define E1000_CTRL_RST 0x04000000 /* Global reset */
+#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
+#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
+#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */
+#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
+#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
+#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */
/* Device Status */
-#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
-#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
-#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
+#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
+#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
+#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
#define E1000_STATUS_FUNC_SHIFT 2
-#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
-#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
-#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
-#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */
+#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */
+#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
+#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
+#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */
#define E1000_STATUS_SPEED_MASK 0x000000C0
-#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
-#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
-#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
-#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion
- by EEPROM/Flash */
-#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
-#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */
-#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
-#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
-#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
-#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
-#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
-#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
-#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */
-#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */
-#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */
-#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
-#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */
-#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
+#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
+#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
+#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
+#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion
+ by EEPROM/Flash */
+#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */
+#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */
+#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
+#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */
+#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */
+#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */
+#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */
+#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */
+#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */
+#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */
+#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */
+#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */
+#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */
+#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */
#define E1000_STATUS_FUSE_8 0x04000000
#define E1000_STATUS_FUSE_9 0x08000000
-#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */
-#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */
+#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */
+#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */
-/* Constants used to intrepret the masked PCI-X bus speed. */
-#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
-#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */
-#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */
+/* Constants used to interpret the masked PCI-X bus speed. */
+#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */
+#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */
+#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */
/* EEPROM/Flash Control */
-#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */
-#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */
-#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */
-#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */
+#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */
+#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */
+#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */
+#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */
#define E1000_EECD_FWE_MASK 0x00000030
-#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */
-#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */
+#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */
+#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */
#define E1000_EECD_FWE_SHIFT 4
-#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */
-#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */
-#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */
-#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
-#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
- * (0-small, 1-large) */
-#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
+#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */
+#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */
+#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */
+#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */
+#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type
+ * (0-small, 1-large) */
+#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */
#ifndef E1000_EEPROM_GRANT_ATTEMPTS
-#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
+#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */
#endif
-#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */
-#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */
+#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */
+#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */
#define E1000_EECD_SIZE_EX_SHIFT 11
-#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
-#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
-#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
-#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
-#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
-#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
-#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
+#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */
+#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */
+#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */
+#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
+#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
+#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */
+#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
#define E1000_EECD_SECVAL_SHIFT 22
#define E1000_STM_OPCODE 0xDB00
#define E1000_HICR_FW_RESET 0xC0
#define E1000_ICH_NVM_SIG_MASK 0xC0
/* EEPROM Read */
-#define E1000_EERD_START 0x00000001 /* Start Read */
-#define E1000_EERD_DONE 0x00000010 /* Read Done */
+#define E1000_EERD_START 0x00000001 /* Start Read */
+#define E1000_EERD_DONE 0x00000010 /* Read Done */
#define E1000_EERD_ADDR_SHIFT 8
-#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */
+#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */
#define E1000_EERD_DATA_SHIFT 16
-#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */
+#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */
/* SPI EEPROM Status Register */
#define EEPROM_STATUS_RDY_SPI 0x01
#define EEPROM_STATUS_WPEN_SPI 0x80
/* Extended Device Control */
-#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */
-#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
+#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */
+#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
#define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN
-#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */
-#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */
-#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
-#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
+#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */
+#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */
+#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
+#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
#define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA
-#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */
-#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
-#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
-#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */
-#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */
-#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */
-#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */
-#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
-#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
-#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
-#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
+#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
+#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
+#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */
+#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */
+#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */
+#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */
+#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
+#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
#define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
#define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000
#define E1000_CTRL_EXT_WR_WMARK_320 0x01000000
#define E1000_CTRL_EXT_WR_WMARK_384 0x02000000
#define E1000_CTRL_EXT_WR_WMARK_448 0x03000000
-#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
-#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
-#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
-#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */
-#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */
+#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
+#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
+#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
+#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */
+#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */
#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000
/* MDI Control */
#define E1000_LEDCTL_MODE_LED_OFF 0xF
/* Receive Address */
-#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
+#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
/* Interrupt Cause Read */
-#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
-#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
-#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
-#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
-#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
-#define E1000_ICR_RXO 0x00000040 /* rx overrun */
-#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
-#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
-#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
-#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
-#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
-#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
-#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
+#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
+#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
+#define E1000_ICR_LSC 0x00000004 /* Link Status Change */
+#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
+#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
+#define E1000_ICR_RXO 0x00000040 /* rx overrun */
+#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
+#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
+#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */
+#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
+#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
+#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
+#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
#define E1000_ICR_TXD_LOW 0x00008000
#define E1000_ICR_SRPD 0x00010000
-#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
-#define E1000_ICR_MNG 0x00040000 /* Manageability event */
-#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
-#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
-#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */
-#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */
-#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */
-#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
-#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
-#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
-#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
-#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */
-#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */
-#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */
+#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
+#define E1000_ICR_MNG 0x00040000 /* Manageability event */
+#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
+#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */
+#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */
+#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
+#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */
+#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */
+#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */
+#define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */
/* Interrupt Cause Set */
-#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
-#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
-#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
-#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
-#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
-#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
-#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
-#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
-#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
-#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
-#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_ICS_SRPD E1000_ICR_SRPD
-#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */
-#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */
-#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */
-#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
-#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
-#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
-#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
-#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
-#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
#define E1000_ICS_DSW E1000_ICR_DSW
#define E1000_ICS_PHYINT E1000_ICR_PHYINT
#define E1000_ICS_EPRST E1000_ICR_EPRST
/* Interrupt Mask Set */
-#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
-#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
-#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
-#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
-#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
-#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
-#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
-#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
-#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
-#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
-#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_IMS_SRPD E1000_ICR_SRPD
-#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */
-#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */
-#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */
-#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
-#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
-#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
-#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
-#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
-#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
#define E1000_IMS_DSW E1000_ICR_DSW
#define E1000_IMS_PHYINT E1000_ICR_PHYINT
#define E1000_IMS_EPRST E1000_ICR_EPRST
/* Interrupt Mask Clear */
-#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
-#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
-#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
-#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
-#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
-#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
-#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
-#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
-#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
-#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
-#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
-#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
-#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
+#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */
+#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */
+#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */
+#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
+#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
+#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */
+#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */
+#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */
+#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */
+#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */
+#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */
+#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */
+#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */
#define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW
#define E1000_IMC_SRPD E1000_ICR_SRPD
-#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */
-#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */
-#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */
-#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
-#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
-#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
-#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
-#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
-#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
+#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */
+#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */
+#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */
+#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */
+#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */
+#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */
+#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */
+#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */
#define E1000_IMC_DSW E1000_ICR_DSW
#define E1000_IMC_PHYINT E1000_ICR_PHYINT
#define E1000_IMC_EPRST E1000_ICR_EPRST
/* Receive Control */
-#define E1000_RCTL_RST 0x00000001 /* Software reset */
-#define E1000_RCTL_EN 0x00000002 /* enable */
-#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
-#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
-#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
-#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
-#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
-#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
-#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
-#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
-#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */
-#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
-#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
-#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
-#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
-#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
-#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
-#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
-#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
-#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
-#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
-#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
+#define E1000_RCTL_RST 0x00000001 /* Software reset */
+#define E1000_RCTL_EN 0x00000002 /* enable */
+#define E1000_RCTL_SBP 0x00000004 /* store bad packet */
+#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
+#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
+#define E1000_RCTL_LPE 0x00000020 /* long packet enable */
+#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
+#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
+#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */
+#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
+#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */
+#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
+#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */
+#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */
+#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
+#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */
+#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */
+#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */
+#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
+#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */
+#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
-#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
-#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
-#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
-#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
+#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
+#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
+#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
+#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
/* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
-#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
-#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
-#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
-#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
-#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
-#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
-#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
-#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
-#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
-#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
-#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */
-#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */
+#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */
+#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */
+#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */
+#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
+#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
+#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
+#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */
+#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
+#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
+#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
+#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */
+#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */
/* Use byte values for the following shift parameters
* Usage:
#define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
#define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
-#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
-#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
-#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
-#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
+#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
+#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
+#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
+#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
/* SW_W_SYNC definitions */
#define E1000_SWFW_EEP_SM 0x0001
#define E1000_SWFW_MAC_CSR_SM 0x0008
/* Receive Descriptor */
-#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
-#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */
-#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */
-#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */
-#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */
+#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */
+#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */
+#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */
+#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */
+#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */
/* Flow Control */
-#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
-#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */
-#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
-#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
+#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
+#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */
+#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
+#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
/* Header split receive */
#define E1000_RFCTL_ISCSI_DIS 0x00000001
#define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
/* Receive Descriptor Control */
-#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
-#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
-#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */
-#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */
+#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */
+#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */
+#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */
+#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */
/* Transmit Descriptor Control */
-#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
-#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
-#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
-#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
-#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
-#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
-#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc.
- still to be processed. */
+#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
+#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
+#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
+#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
+#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */
+#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
+#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc.
+ still to be processed. */
/* Transmit Configuration Word */
-#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
-#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
-#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
-#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
-#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
-#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */
-#define E1000_TXCW_NP 0x00008000 /* TXCW next page */
-#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */
-#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */
-#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
+#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
+#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */
+#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
+#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
+#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
+#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */
+#define E1000_TXCW_NP 0x00008000 /* TXCW next page */
+#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */
+#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */
+#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
/* Receive Configuration Word */
-#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
-#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */
-#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
-#define E1000_RXCW_CC 0x10000000 /* Receive config change */
-#define E1000_RXCW_C 0x20000000 /* Receive config */
-#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
-#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */
+#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
+#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */
+#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
+#define E1000_RXCW_CC 0x10000000 /* Receive config change */
+#define E1000_RXCW_C 0x20000000 /* Receive config */
+#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
+#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */
/* Transmit Control */
-#define E1000_TCTL_RST 0x00000001 /* software reset */
-#define E1000_TCTL_EN 0x00000002 /* enable tx */
-#define E1000_TCTL_BCE 0x00000004 /* busy check enable */
-#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
-#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
-#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
-#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */
-#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
-#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
-#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
-#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
+#define E1000_TCTL_RST 0x00000001 /* software reset */
+#define E1000_TCTL_EN 0x00000002 /* enable tx */
+#define E1000_TCTL_BCE 0x00000004 /* busy check enable */
+#define E1000_TCTL_PSP 0x00000008 /* pad short packets */
+#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
+#define E1000_TCTL_COLD 0x003ff000 /* collision distance */
+#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */
+#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */
+#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
+#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */
+#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
/* Extended Transmit Control */
-#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */
-#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
-
-#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000
+#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */
+#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */
/* Receive Checksum Control */
-#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
-#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
-#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
-#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
-#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
-#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
+#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */
+#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
+#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
+#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */
+#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
+#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
/* Multiple Receive Queue Control */
#define E1000_MRQC_ENABLE_MASK 0x00000003
/* Definitions for power management and wakeup registers */
/* Wake Up Control */
-#define E1000_WUC_APME 0x00000001 /* APM Enable */
-#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
-#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
-#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
-#define E1000_WUC_SPM 0x80000000 /* Enable SPM */
+#define E1000_WUC_APME 0x00000001 /* APM Enable */
+#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
+#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
+#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
+#define E1000_WUC_SPM 0x80000000 /* Enable SPM */
/* Wake Up Filter Control */
-#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
-#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
-#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
-#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
-#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
-#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
-#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
-#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
-#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */
-#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
-#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
-#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
-#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
-#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
-#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */
-#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
+#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
+#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
+#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
+#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
+#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
+#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
+#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
+#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
+#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */
+#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
+#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
+#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
+#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
+#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */
+#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */
+#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
/* Wake Up Status */
-#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */
-#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */
-#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */
-#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */
-#define E1000_WUS_BC 0x00000010 /* Broadcast Received */
-#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */
-#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */
-#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */
-#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */
-#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */
-#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */
-#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */
-#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
+#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */
+#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */
+#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */
+#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */
+#define E1000_WUS_BC 0x00000010 /* Broadcast Received */
+#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */
+#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */
+#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */
+#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */
+#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */
+#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */
+#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */
+#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
/* Management Control */
-#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
-#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
-#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */
-#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */
-#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */
-#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */
-#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */
-#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */
-#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
-#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery
- * Filtering */
-#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */
-#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
-#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
-#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
-#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */
-#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
-#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address
- * filtering */
-#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host
- * memory */
-#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address
- * filtering */
-#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
-#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
-#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
-#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
-#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
-#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */
-#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */
-#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */
-
-#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
-#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
+#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
+#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
+#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */
+#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */
+#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */
+#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */
+#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */
+#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */
+#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
+#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery
+ * Filtering */
+#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */
+#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */
+#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
+#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */
+#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */
+#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
+#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address
+ * filtering */
+#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host
+ * memory */
+#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address
+ * filtering */
+#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */
+#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */
+#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */
+#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */
+#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */
+#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */
+#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */
+#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */
+
+#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */
+#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */
/* SW Semaphore Register */
-#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
-#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
-#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
-#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
+#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
+#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
+#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */
+#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
/* FW Semaphore Register */
-#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */
+#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */
#define E1000_FWSM_MODE_SHIFT 1
-#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
+#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */
-#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */
-#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */
-#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */
+#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */
+#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */
+#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */
#define E1000_FWSM_SKUEL_SHIFT 29
-#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */
-#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */
-#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
-#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
+#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */
+#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */
+#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */
+#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */
/* FFLT Debug Register */
-#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */
+#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */
typedef enum {
- e1000_mng_mode_none = 0,
- e1000_mng_mode_asf,
- e1000_mng_mode_pt,
- e1000_mng_mode_ipmi,
- e1000_mng_mode_host_interface_only
+ e1000_mng_mode_none = 0,
+ e1000_mng_mode_asf,
+ e1000_mng_mode_pt,
+ e1000_mng_mode_ipmi,
+ e1000_mng_mode_host_interface_only
} e1000_mng_mode;
-/* Host Inteface Control Register */
-#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */
-#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done
- * to put command in RAM */
-#define E1000_HICR_SV 0x00000004 /* Status Validity */
-#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */
+/* Host Interface Control Register */
+#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */
+#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done
+ * to put command in RAM */
+#define E1000_HICR_SV 0x00000004 /* Status Validity */
+#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */
/* Host Interface Command Interface - Address range 0x8800-0x8EFF */
-#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */
-#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */
-#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */
-#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */
+#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */
+#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */
+#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */
+#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */
struct e1000_host_command_header {
- u8 command_id;
- u8 command_length;
- u8 command_options; /* I/F bits for command, status for return */
- u8 checksum;
+ u8 command_id;
+ u8 command_length;
+ u8 command_options; /* I/F bits for command, status for return */
+ u8 checksum;
};
struct e1000_host_command_info {
- struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
- u8 command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */
+ struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */
+ u8 command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */
};
/* Host SMB register #0 */
-#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */
-#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */
-#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */
-#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */
+#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */
+#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */
+#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */
+#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */
/* Host SMB register #1 */
#define E1000_HSMC1R_CLKIN E1000_HSMC0R_CLKIN
#define E1000_HSMC1R_CLKOUT E1000_HSMC0R_CLKOUT
/* FW Status Register */
-#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */
+#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */
/* Wake Up Packet Length */
-#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
+#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */
#define E1000_MDALIGN 4096
#define PCI_EX_LINK_WIDTH_SHIFT 4
/* EEPROM Commands - Microwire */
-#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */
-#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */
-#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */
-#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */
-#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erast/write disable */
+#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */
+#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */
+#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */
+#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erase/write disable */
/* EEPROM Commands - SPI */
-#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
-#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
-#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
-#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
-#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */
-#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */
-#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */
-#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */
-#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */
-#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */
-#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */
+#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
+#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */
+#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */
+#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
+#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */
+#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */
+#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */
+#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */
+#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */
+#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */
+#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */
/* EEPROM Size definitions */
#define EEPROM_WORD_SIZE_SHIFT 6
#define EEPROM_COMPAT 0x0003
#define EEPROM_ID_LED_SETTINGS 0x0004
#define EEPROM_VERSION 0x0005
-#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */
+#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */
#define EEPROM_PHY_CLASS_WORD 0x0007
#define EEPROM_INIT_CONTROL1_REG 0x000A
#define EEPROM_INIT_CONTROL2_REG 0x000F
#define EEPROM_FLASH_VERSION 0x0032
#define EEPROM_CHECKSUM_REG 0x003F
-#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */
-#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */
+#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */
+#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */
/* Word definitions for ID LED Settings */
#define ID_LED_RESERVED_0000 0x0000
#define ID_LED_RESERVED_FFFF 0xFFFF
-#define ID_LED_RESERVED_82573 0xF746
-#define ID_LED_DEFAULT_82573 0x1811
#define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
(ID_LED_OFF1_OFF2 << 8) | \
(ID_LED_DEF1_DEF2 << 4) | \
(ID_LED_DEF1_DEF2))
-#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \
- (ID_LED_DEF1_OFF2 << 8) | \
- (ID_LED_DEF1_ON2 << 4) | \
- (ID_LED_DEF1_DEF2))
#define ID_LED_DEF1_DEF2 0x1
#define ID_LED_DEF1_ON2 0x2
#define ID_LED_DEF1_OFF2 0x3
#define IGP_ACTIVITY_LED_ENABLE 0x0300
#define IGP_LED3_MODE 0x07000000
-
/* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */
#define EEPROM_SERDES_AMPLITUDE_MASK 0x000F
#define DEFAULT_82542_TIPG_IPGR2 10
#define DEFAULT_82543_TIPG_IPGR2 6
-#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
#define E1000_TIPG_IPGR2_SHIFT 20
-#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009
-#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008
#define E1000_TXDMAC_DPP 0x00000001
/* Adaptive IFS defines */
#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
/* PBA constants */
-#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */
-#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */
-#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
+#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */
+#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */
+#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
#define E1000_PBA_20K 0x0014
#define E1000_PBA_22K 0x0016
#define E1000_PBA_24K 0x0018
#define E1000_PBA_34K 0x0022
#define E1000_PBA_38K 0x0026
#define E1000_PBA_40K 0x0028
-#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
+#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */
#define E1000_PBS_16K E1000_PBA_16K
#define FLOW_CONTROL_TYPE 0x8808
/* The historical defaults for the flow control values are given below. */
-#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */
-#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */
-#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */
+#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */
+#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */
+#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */
/* PCIX Config space */
#define PCIX_COMMAND_REGISTER 0xE6
#define PCIX_STATUS_HI_MMRBC_4K 0x3
#define PCIX_STATUS_HI_MMRBC_2K 0x2
-
/* Number of bits required to shift right the "pause" bits from the
* EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register.
*/
*/
#define ILOS_SHIFT 3
-
#define RECEIVE_BUFFER_ALIGN_SIZE (256)
/* Number of milliseconds we wait for auto-negotiation to complete */
#define LINK_UP_TIMEOUT 500
-/* Number of 100 microseconds we wait for PCI Express master disable */
-#define MASTER_DISABLE_TIMEOUT 800
/* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */
#define AUTO_READ_DONE_TIMEOUT 10
/* Number of milliseconds we wait for PHY configuration done after MAC reset */
(((length) > (adapter)->min_frame_size) && \
((length) <= ((adapter)->max_frame_size + VLAN_TAG_SIZE + 1)))))
-
/* Structures, enums, and macros for the PHY */
/* Bit definitions for the Management Data IO (MDIO) and Management Data
/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
-#define PHY_CTRL 0x00 /* Control Register */
-#define PHY_STATUS 0x01 /* Status Regiser */
-#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
-#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
-#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
-#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
-#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
-#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
-#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
-#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
-#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
-#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
-
-#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
-#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */
+#define PHY_CTRL 0x00 /* Control Register */
+#define PHY_STATUS 0x01 /* Status Register */
+#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
+#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
+#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */
+
+#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
+#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */
/* M88E1000 Specific Registers */
-#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
-#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
-#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */
-#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */
-#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
-#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
-
-#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */
-#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
-#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
-#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */
-#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */
+#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
+#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
+#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */
+#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */
+#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
+#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */
+
+#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */
+#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
+#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
+#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */
+#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */
#define IGP01E1000_IEEE_REGS_PAGE 0x0000
#define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300
#define IGP01E1000_IEEE_FORCE_GIGA 0x0140
/* IGP01E1000 Specific Registers */
-#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */
-#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */
-#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */
-#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */
-#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */
-#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */
+#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */
+#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */
+#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */
+#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */
+#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */
+#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */
#define IGP02E1000_PHY_POWER_MGMT 0x19
-#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */
+#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */
/* IGP01E1000 AGC Registers - stores the cable length values*/
#define IGP01E1000_PHY_AGC_A 0x1172
#define IGP01E1000_ANALOG_REGS_PAGE 0x20C0
-/* Bits...
- * 15-5: page
- * 4-0: register offset
- */
-#define GG82563_PAGE_SHIFT 5
-#define GG82563_REG(page, reg) \
- (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
-#define GG82563_MIN_ALT_REG 30
-
-/* GG82563 Specific Registers */
-#define GG82563_PHY_SPEC_CTRL \
- GG82563_REG(0, 16) /* PHY Specific Control */
-#define GG82563_PHY_SPEC_STATUS \
- GG82563_REG(0, 17) /* PHY Specific Status */
-#define GG82563_PHY_INT_ENABLE \
- GG82563_REG(0, 18) /* Interrupt Enable */
-#define GG82563_PHY_SPEC_STATUS_2 \
- GG82563_REG(0, 19) /* PHY Specific Status 2 */
-#define GG82563_PHY_RX_ERR_CNTR \
- GG82563_REG(0, 21) /* Receive Error Counter */
-#define GG82563_PHY_PAGE_SELECT \
- GG82563_REG(0, 22) /* Page Select */
-#define GG82563_PHY_SPEC_CTRL_2 \
- GG82563_REG(0, 26) /* PHY Specific Control 2 */
-#define GG82563_PHY_PAGE_SELECT_ALT \
- GG82563_REG(0, 29) /* Alternate Page Select */
-#define GG82563_PHY_TEST_CLK_CTRL \
- GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */
-
-#define GG82563_PHY_MAC_SPEC_CTRL \
- GG82563_REG(2, 21) /* MAC Specific Control Register */
-#define GG82563_PHY_MAC_SPEC_CTRL_2 \
- GG82563_REG(2, 26) /* MAC Specific Control 2 */
-
-#define GG82563_PHY_DSP_DISTANCE \
- GG82563_REG(5, 26) /* DSP Distance */
-
-/* Page 193 - Port Control Registers */
-#define GG82563_PHY_KMRN_MODE_CTRL \
- GG82563_REG(193, 16) /* Kumeran Mode Control */
-#define GG82563_PHY_PORT_RESET \
- GG82563_REG(193, 17) /* Port Reset */
-#define GG82563_PHY_REVISION_ID \
- GG82563_REG(193, 18) /* Revision ID */
-#define GG82563_PHY_DEVICE_ID \
- GG82563_REG(193, 19) /* Device ID */
-#define GG82563_PHY_PWR_MGMT_CTRL \
- GG82563_REG(193, 20) /* Power Management Control */
-#define GG82563_PHY_RATE_ADAPT_CTRL \
- GG82563_REG(193, 25) /* Rate Adaptation Control */
-
-/* Page 194 - KMRN Registers */
-#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \
- GG82563_REG(194, 16) /* FIFO's Control/Status */
-#define GG82563_PHY_KMRN_CTRL \
- GG82563_REG(194, 17) /* Control */
-#define GG82563_PHY_INBAND_CTRL \
- GG82563_REG(194, 18) /* Inband Control */
-#define GG82563_PHY_KMRN_DIAGNOSTIC \
- GG82563_REG(194, 19) /* Diagnostic */
-#define GG82563_PHY_ACK_TIMEOUTS \
- GG82563_REG(194, 20) /* Acknowledge Timeouts */
-#define GG82563_PHY_ADV_ABILITY \
- GG82563_REG(194, 21) /* Advertised Ability */
-#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \
- GG82563_REG(194, 23) /* Link Partner Advertised Ability */
-#define GG82563_PHY_ADV_NEXT_PAGE \
- GG82563_REG(194, 24) /* Advertised Next Page */
-#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \
- GG82563_REG(194, 25) /* Link Partner Advertised Next page */
-#define GG82563_PHY_KMRN_MISC \
- GG82563_REG(194, 26) /* Misc. */
-
/* PHY Control Register */
-#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
-#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
-#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
-#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
-#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
-#define MII_CR_POWER_DOWN 0x0800 /* Power down */
-#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
-#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
-#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
-#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
+#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */
+#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
+#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */
+#define MII_CR_POWER_DOWN 0x0800 /* Power down */
+#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
+#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
/* PHY Status Register */
-#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
-#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
-#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
-#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
-#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
-#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
-#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
-#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
-#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
-#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
-#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
-#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
-#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
-#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
-#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
+#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */
+#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */
+#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */
+#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */
+#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
+#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
+#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */
+#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */
+#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */
+#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */
+#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */
+#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */
+#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */
+#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */
/* Autoneg Advertisement Register */
-#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
-#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
-#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
-#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
-#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
-#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
-#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
-#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
-#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
-#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */
+#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
+#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */
+#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
+#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
+#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */
+#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */
/* Link Partner Ability Register (Base Page) */
-#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
-#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */
-#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */
-#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */
-#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */
-#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */
-#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
-#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
-#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */
-#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */
-#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */
+#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
+#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */
+#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */
+#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */
+#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */
+#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */
+#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
+#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */
+#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */
+#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */
/* Autoneg Expansion Register */
-#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
-#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */
-#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */
-#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
-#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */
+#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */
+#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */
+#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */
+#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
+#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */
/* Next Page TX Register */
-#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
-#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges
- * of different NP
- */
-#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
- * 0 = cannot comply with msg
- */
-#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
-#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
- * 0 = sending last NP
- */
+#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges
+ * of different NP
+ */
+#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
+ * 0 = cannot comply with msg
+ */
+#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
+#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
+ * 0 = sending last NP
+ */
/* Link Partner Next Page Register */
-#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
-#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges
- * of different NP
- */
-#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
- * 0 = cannot comply with msg
- */
-#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
-#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */
-#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
- * 0 = sending last NP
- */
+#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges
+ * of different NP
+ */
+#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg
+ * 0 = cannot comply with msg
+ */
+#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */
+#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */
+#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow
+ * 0 = sending last NP
+ */
/* 1000BASE-T Control Register */
-#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
-#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
-#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
-#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */
- /* 0=DTE device */
-#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
- /* 0=Configure PHY as Slave */
-#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
- /* 0=Automatic Master/Slave config */
-#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
-#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
-#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
-#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
-#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
+#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */
+#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
+#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */
+ /* 0=DTE device */
+#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
+ /* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
+ /* 0=Automatic Master/Slave config */
+#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
+#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */
+#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */
+#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */
+#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */
/* 1000BASE-T Status Register */
-#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */
-#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */
-#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
-#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
-#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
-#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
-#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
-#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
+#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */
+#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */
+#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */
+#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
+#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */
+#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */
#define SR_1000T_REMOTE_RX_STATUS_SHIFT 12
#define SR_1000T_LOCAL_RX_STATUS_SHIFT 13
#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5
#define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100
/* Extended Status Register */
-#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
-#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
-#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
-#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
+#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
+#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
+#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
+#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
-#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */
-#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */
+#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */
+#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */
-#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */
- /* (0=enable, 1=disable) */
+#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */
+ /* (0=enable, 1=disable) */
/* M88E1000 PHY Specific Control Register */
-#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
-#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
-#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
-#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low,
- * 0=CLK125 toggling
- */
-#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
- /* Manual MDI configuration */
-#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
-#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover,
- * 100BASE-TX/10BASE-T:
- * MDI Mode
- */
-#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled
- * all speeds.
- */
+#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */
+#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
+#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */
+#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low,
+ * 0=CLK125 toggling
+ */
+#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
+ /* Manual MDI configuration */
+#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
+#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover,
+ * 100BASE-TX/10BASE-T:
+ * MDI Mode
+ */
+#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled
+ * all speeds.
+ */
#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080
- /* 1=Enable Extended 10BASE-T distance
- * (Lower 10BASE-T RX Threshold)
- * 0=Normal 10BASE-T RX Threshold */
+ /* 1=Enable Extended 10BASE-T distance
+ * (Lower 10BASE-T RX Threshold)
+ * 0=Normal 10BASE-T RX Threshold */
#define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100
- /* 1=5-Bit interface in 100BASE-TX
- * 0=MII interface in 100BASE-TX */
-#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
-#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
-#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
+ /* 1=5-Bit interface in 100BASE-TX
+ * 0=MII interface in 100BASE-TX */
+#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */
+#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */
+#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
#define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT 1
#define M88E1000_PSCR_AUTO_X_MODE_SHIFT 5
#define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7
/* M88E1000 PHY Specific Status Register */
-#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */
-#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
-#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
-#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
-#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M;
- * 3=110-140M;4=>140M */
-#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */
-#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
-#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */
-#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
-#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
-#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */
-#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */
-#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
+#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */
+#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
+#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
+#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
+#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M;
+ * 3=110-140M;4=>140M */
+#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */
+#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */
+#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */
+#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */
+#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
+#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */
+#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */
+#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
#define M88E1000_PSSR_REV_POLARITY_SHIFT 1
#define M88E1000_PSSR_DOWNSHIFT_SHIFT 5
#define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
/* M88E1000 Extended PHY Specific Control Register */
-#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
-#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled.
- * Will assert lost lock and bring
- * link down if idle not seen
- * within 1ms in 1000BASE-T
- */
+#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */
+#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled.
+ * Will assert lost lock and bring
+ * link down if idle not seen
+ * within 1ms in 1000BASE-T
+ */
/* Number of times we will attempt to autonegotiate before downshifting if we
* are the master */
#define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200
#define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300
-#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */
-#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
-#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
+#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */
/* M88EC018 Rev 2 specific DownShift settings */
#define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
#define IGP01E1000_PSCFR_DISABLE_TRANSMIT 0x2000
/* IGP01E1000 Specific Port Status Register - R/O */
-#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */
+#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */
#define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002
#define IGP01E1000_PSSR_CABLE_LENGTH 0x007C
#define IGP01E1000_PSSR_FULL_DUPLEX 0x0200
#define IGP01E1000_PSSR_LINK_UP 0x0400
#define IGP01E1000_PSSR_MDIX 0x0800
-#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */
+#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */
#define IGP01E1000_PSSR_SPEED_10MBPS 0x4000
#define IGP01E1000_PSSR_SPEED_100MBPS 0x8000
#define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000
-#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */
-#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */
+#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */
+#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */
/* IGP01E1000 Specific Port Control Register - R/W */
#define IGP01E1000_PSCR_TP_LOOPBACK 0x0010
#define IGP01E1000_PSCR_TEN_CRS_SELECT 0x0400
#define IGP01E1000_PSCR_FLIP_CHIP 0x0800
#define IGP01E1000_PSCR_AUTO_MDIX 0x1000
-#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */
+#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */
/* IGP01E1000 Specific Port Link Health Register */
#define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000
#define IGP01E1000_PLHR_GIG_SCRAMBLER_ERROR 0x4000
#define IGP01E1000_PLHR_MASTER_FAULT 0x2000
#define IGP01E1000_PLHR_MASTER_RESOLUTION 0x1000
-#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */
-#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */
-#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */
+#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */
+#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */
+#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */
#define IGP01E1000_PLHR_DATA_ERR_0 0x0100
#define IGP01E1000_PLHR_AUTONEG_FAULT 0x0040
#define IGP01E1000_PLHR_AUTONEG_ACTIVE 0x0010
#define IGP01E1000_MSE_CHANNEL_B 0x0F00
#define IGP01E1000_MSE_CHANNEL_A 0xF000
-#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
-#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */
-#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */
+#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */
+#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */
+#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */
/* IGP01E1000 DSP reset macros */
#define DSP_RESET_ENABLE 0x0
/* IGP01E1000 & IGP02E1000 AGC Registers */
-#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */
-#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */
+#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */
+#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */
/* IGP02E1000 AGC Register Length 9-bit mask */
#define IGP02E1000_AGC_LENGTH_MASK 0x7F
#define IGP01E1000_PHY_POLARITY_MASK 0x0078
/* IGP01E1000 GMII FIFO Register */
-#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed
- * on Link-Up */
-#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */
+#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed
+ * on Link-Up */
+#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */
/* IGP01E1000 Analog Register */
#define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1
#define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080
#define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500
-/* GG82563 PHY Specific Status Register (Page 0, Register 16 */
-#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */
-#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal Disabled */
-#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */
-#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter Disabled */
-#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060
-#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI configuration */
-#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX configuration */
-#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic crossover */
-#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended Distance */
-#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300
-#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */
-#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only (Energy Detect) */
-#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */
-#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */
-#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */
-#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000
-#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12
-
-/* PHY Specific Status Register (Page 0, Register 17) */
-#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */
-#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */
-#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */
-#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */
-#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */
-#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */
-#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */
-#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */
-#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */
-#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */
-#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */
-#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */
-#define GG82563_PSSR_SPEED_MASK 0xC000
-#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */
-#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */
-#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */
-
-/* PHY Specific Status Register 2 (Page 0, Register 19) */
-#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */
-#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */
-#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */
-#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */
-#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */
-#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=False Carrier */
-#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */
-#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */
-#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */
-#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */
-#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */
-#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */
-#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */
-
-/* PHY Specific Control Register 2 (Page 0, Register 26) */
-#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative Polarity */
-#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C
-#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal Operation */
-#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns Sequence */
-#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns Sequence */
-#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */
-#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable 1000BASE-T */
-#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000
-#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */
-#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */
-
-/* MAC Specific Control Register (Page 2, Register 21) */
-/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */
-#define GG82563_MSCR_TX_CLK_MASK 0x0007
-#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004
-#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005
-#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006
-#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007
-
-#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */
-
-/* DSP Distance Register (Page 5, Register 26) */
-#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M;
- 1 = 50-80M;
- 2 = 80-110M;
- 3 = 110-140M;
- 4 = >140M */
-
-/* Kumeran Mode Control Register (Page 193, Register 16) */
-#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */
-#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */
-#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080
-#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400
-#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz, 0=0.8MHz */
-#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800
-
-/* Power Management Control Register (Page 193, Register 20) */
-#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES Electrical Idle */
-#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */
-#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */
-#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse Auto-Negotiation */
-#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps Auto-Neg in non D0 */
-#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps Auto-Neg Always */
-#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a Reverse Auto-Negotiation */
-#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */
-#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300
-#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */
-#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */
-#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */
-#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */
-
-/* In-Band Control Register (Page 194, Register 18) */
-#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */
-
-
/* Bit definitions for valid PHY IDs. */
/* I = Integrated
* E = External
#define M88E1011_I_REV_4 0x04
#define M88E1111_I_PHY_ID 0x01410CC0
#define L1LXT971A_PHY_ID 0x001378E0
-#define GG82563_E_PHY_ID 0x01410CA0
-
/* Bits...
* 15-5: page
(((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
#define IGP3_PHY_PORT_CTRL \
- PHY_REG(769, 17) /* Port General Configuration */
+ PHY_REG(769, 17) /* Port General Configuration */
#define IGP3_PHY_RATE_ADAPT_CTRL \
- PHY_REG(769, 25) /* Rate Adapter Control Register */
+ PHY_REG(769, 25) /* Rate Adapter Control Register */
#define IGP3_KMRN_FIFO_CTRL_STATS \
- PHY_REG(770, 16) /* KMRN FIFO's control/status register */
+ PHY_REG(770, 16) /* KMRN FIFO's control/status register */
#define IGP3_KMRN_POWER_MNG_CTRL \
- PHY_REG(770, 17) /* KMRN Power Management Control Register */
+ PHY_REG(770, 17) /* KMRN Power Management Control Register */
#define IGP3_KMRN_INBAND_CTRL \
- PHY_REG(770, 18) /* KMRN Inband Control Register */
+ PHY_REG(770, 18) /* KMRN Inband Control Register */
#define IGP3_KMRN_DIAG \
- PHY_REG(770, 19) /* KMRN Diagnostic register */
-#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
+ PHY_REG(770, 19) /* KMRN Diagnostic register */
+#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */
#define IGP3_KMRN_ACK_TIMEOUT \
- PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
+ PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */
#define IGP3_VR_CTRL \
- PHY_REG(776, 18) /* Voltage regulator control register */
-#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
-#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */
+ PHY_REG(776, 18) /* Voltage regulator control register */
+#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
+#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */
#define IGP3_CAPABILITY \
- PHY_REG(776, 19) /* IGP3 Capability Register */
+ PHY_REG(776, 19) /* IGP3 Capability Register */
/* Capabilities for SKU Control */
-#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */
-#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */
-#define IGP3_CAP_ASF 0x0004 /* Support ASF */
-#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */
-#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */
-#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */
-#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */
-#define IGP3_CAP_RSS 0x0080 /* Support RSS */
-#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */
-#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */
+#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */
+#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */
+#define IGP3_CAP_ASF 0x0004 /* Support ASF */
+#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */
+#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */
+#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */
+#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */
+#define IGP3_CAP_RSS 0x0080 /* Support RSS */
+#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */
+#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */
#define IGP3_PPC_JORDAN_EN 0x0001
#define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002
#define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020
#define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040
-#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */
-#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */
+#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */
+#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */
#define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18)
#define IGP3_KMRN_EC_DIS_INBAND 0x0080
#define IGP03E1000_E_PHY_ID 0x02A80390
-#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
+#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */
#define IFE_PLUS_E_PHY_ID 0x02A80320
#define IFE_C_E_PHY_ID 0x02A80310
-#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */
-#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */
-#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */
-#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet Counter */
-#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */
-#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */
-#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */
-#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */
-#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */
-#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */
-#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */
-#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
-#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */
-
-#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto reduced power down */
-#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */
-#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */
-#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */
-#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */
-#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
-#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */
+#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */
+#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */
+#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */
+#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnect Counter */
+#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */
+#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */
+#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */
+#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */
+#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */
+#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */
+#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */
+#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */
+#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */
+
+#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Default 1 = Disable auto reduced power down */
+#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */
+#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */
+#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */
+#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */
+#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */
+#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */
#define IFE_PESC_POLARITY_REVERSED_SHIFT 8
-#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down disabled */
-#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */
-#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */
-#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */
+#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dynamic Power Down disabled */
+#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */
+#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */
+#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */
#define IFE_PSC_FORCE_POLARITY_SHIFT 5
#define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4
-#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */
-#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */
-#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
-#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm is completed */
+#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */
+#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */
+#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */
+#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm is completed */
#define IFE_PMC_MDIX_MODE_SHIFT 6
-#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
-
-#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */
-#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */
-#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */
-#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
-#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
-#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */
-#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */
-#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
-#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
-#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
-#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
-
-#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */
-#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */
-#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */
+#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */
+
+#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */
+#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */
+#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */
+#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */
+#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */
+#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */
+#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */
+#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */
+#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */
+#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */
+#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */
+
+#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */
+#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */
+#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */
#define ICH_FLASH_SEG_SIZE_256 256
#define ICH_FLASH_SEG_SIZE_4K 4096
#define ICH_FLASH_SEG_SIZE_64K 65536
#define ICH_GFPREG_BASE_MASK 0x1FFF
#define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
-/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
-/* Offset 04h HSFSTS */
-union ich8_hws_flash_status {
- struct ich8_hsfsts {
-#ifdef __BIG_ENDIAN
- u16 reserved2 :6;
- u16 fldesvalid :1;
- u16 flockdn :1;
- u16 flcdone :1;
- u16 flcerr :1;
- u16 dael :1;
- u16 berasesz :2;
- u16 flcinprog :1;
- u16 reserved1 :2;
-#else
- u16 flcdone :1; /* bit 0 Flash Cycle Done */
- u16 flcerr :1; /* bit 1 Flash Cycle Error */
- u16 dael :1; /* bit 2 Direct Access error Log */
- u16 berasesz :2; /* bit 4:3 Block/Sector Erase Size */
- u16 flcinprog :1; /* bit 5 flash SPI cycle in Progress */
- u16 reserved1 :2; /* bit 13:6 Reserved */
- u16 reserved2 :6; /* bit 13:6 Reserved */
- u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */
- u16 flockdn :1; /* bit 15 Flash Configuration Lock-Down */
-#endif
- } hsf_status;
- u16 regval;
-};
-
-/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */
-/* Offset 06h FLCTL */
-union ich8_hws_flash_ctrl {
- struct ich8_hsflctl {
-#ifdef __BIG_ENDIAN
- u16 fldbcount :2;
- u16 flockdn :6;
- u16 flcgo :1;
- u16 flcycle :2;
- u16 reserved :5;
-#else
- u16 flcgo :1; /* 0 Flash Cycle Go */
- u16 flcycle :2; /* 2:1 Flash Cycle */
- u16 reserved :5; /* 7:3 Reserved */
- u16 fldbcount :2; /* 9:8 Flash Data Byte Count */
- u16 flockdn :6; /* 15:10 Reserved */
-#endif
- } hsf_ctrl;
- u16 regval;
-};
-
-/* ICH8 Flash Region Access Permissions */
-union ich8_hws_flash_regacc {
- struct ich8_flracc {
-#ifdef __BIG_ENDIAN
- u32 gmwag :8;
- u32 gmrag :8;
- u32 grwa :8;
- u32 grra :8;
-#else
- u32 grra :8; /* 0:7 GbE region Read Access */
- u32 grwa :8; /* 8:15 GbE region Write Access */
- u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */
- u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */
-#endif
- } hsf_flregacc;
- u16 regval;
-};
-
/* Miscellaneous PHY bit definitions. */
#define PHY_PREAMBLE 0xFFFFFFFF
#define PHY_SOF 0x01
#define MII_CR_SPEED_100 0x2000
#define MII_CR_SPEED_10 0x0000
#define E1000_PHY_ADDRESS 0x01
-#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */
-#define PHY_FORCE_TIME 20 /* 2.0 Seconds */
+#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */
+#define PHY_FORCE_TIME 20 /* 2.0 Seconds */
#define PHY_REVISION_MASK 0xFFFFFFF0
-#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */
+#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */
#define REG4_SPEED_MASK 0x01E0
#define REG9_SPEED_MASK 0x0300
#define ADVERTISE_10_HALF 0x0001
#define ADVERTISE_100_FULL 0x0008
#define ADVERTISE_1000_HALF 0x0010
#define ADVERTISE_1000_FULL 0x0020
-#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
-#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds*/
-#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds*/
+#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */
+#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds */
+#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds */
#endif /* _E1000_HW_H_ */
char e1000_driver_name[] = "e1000";
static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
-#define DRV_VERSION "7.3.21-k3-NAPI"
+#define DRV_VERSION "7.3.21-k5-NAPI"
const char e1000_driver_version[] = DRV_VERSION;
static const char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
static int e1000_change_mtu(struct net_device *netdev, int new_mtu);
static int e1000_set_mac(struct net_device *netdev, void *p);
static irqreturn_t e1000_intr(int irq, void *data);
-static irqreturn_t e1000_intr_msi(int irq, void *data);
static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
struct e1000_tx_ring *tx_ring);
static int e1000_clean(struct napi_struct *napi, int budget);
static int e1000_request_irq(struct e1000_adapter *adapter)
{
- struct e1000_hw *hw = &adapter->hw;
struct net_device *netdev = adapter->netdev;
irq_handler_t handler = e1000_intr;
int irq_flags = IRQF_SHARED;
int err;
- if (hw->mac_type >= e1000_82571) {
- adapter->have_msi = !pci_enable_msi(adapter->pdev);
- if (adapter->have_msi) {
- handler = e1000_intr_msi;
- irq_flags = 0;
- }
- }
-
err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name,
netdev);
if (err) {
- if (adapter->have_msi)
- pci_disable_msi(adapter->pdev);
DPRINTK(PROBE, ERR,
"Unable to allocate interrupt Error: %d\n", err);
}
struct net_device *netdev = adapter->netdev;
free_irq(adapter->pdev->irq, netdev);
-
- if (adapter->have_msi)
- pci_disable_msi(adapter->pdev);
}
/**
}
}
-/**
- * e1000_release_hw_control - release control of the h/w to f/w
- * @adapter: address of board private structure
- *
- * e1000_release_hw_control resets {CTRL_EXT|FWSM}:DRV_LOAD bit.
- * For ASF and Pass Through versions of f/w this means that the
- * driver is no longer loaded. For AMT version (only with 82573) i
- * of the f/w this means that the network i/f is closed.
- *
- **/
-
-static void e1000_release_hw_control(struct e1000_adapter *adapter)
-{
- u32 ctrl_ext;
- u32 swsm;
- struct e1000_hw *hw = &adapter->hw;
-
- /* Let firmware taken over control of h/w */
- switch (hw->mac_type) {
- case e1000_82573:
- swsm = er32(SWSM);
- ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD);
- break;
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
- case e1000_ich8lan:
- ctrl_ext = er32(CTRL_EXT);
- ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
- break;
- default:
- break;
- }
-}
-
-/**
- * e1000_get_hw_control - get control of the h/w from f/w
- * @adapter: address of board private structure
- *
- * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
- * For ASF and Pass Through versions of f/w this means that
- * the driver is loaded. For AMT version (only with 82573)
- * of the f/w this means that the network i/f is open.
- *
- **/
-
-static void e1000_get_hw_control(struct e1000_adapter *adapter)
-{
- u32 ctrl_ext;
- u32 swsm;
- struct e1000_hw *hw = &adapter->hw;
-
- /* Let firmware know the driver has taken over */
- switch (hw->mac_type) {
- case e1000_82573:
- swsm = er32(SWSM);
- ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
- break;
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
- case e1000_ich8lan:
- ctrl_ext = er32(CTRL_EXT);
- ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
- break;
- default:
- break;
- }
-}
-
static void e1000_init_manageability(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
/* disable hardware interception of ARP */
manc &= ~(E1000_MANC_ARP_EN);
- /* enable receiving management packets to the host */
- /* this will probably generate destination unreachable messages
- * from the host OS, but the packets will be handled on SMBUS */
- if (hw->has_manc2h) {
- u32 manc2h = er32(MANC2H);
-
- manc |= E1000_MANC_EN_MNG2HOST;
-#define E1000_MNG2HOST_PORT_623 (1 << 5)
-#define E1000_MNG2HOST_PORT_664 (1 << 6)
- manc2h |= E1000_MNG2HOST_PORT_623;
- manc2h |= E1000_MNG2HOST_PORT_664;
- ew32(MANC2H, manc2h);
- }
-
ew32(MANC, manc);
}
}
/* re-enable hardware interception of ARP */
manc |= E1000_MANC_ARP_EN;
- if (hw->has_manc2h)
- manc &= ~E1000_MANC_EN_MNG2HOST;
-
- /* don't explicitly have to mess with MANC2H since
- * MANC has an enable disable that gates MANC2H */
-
ew32(MANC, manc);
}
}
if (er32(MANC) & E1000_MANC_SMBUS_EN)
goto out;
break;
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_80003es2lan:
- case e1000_ich8lan:
- if (e1000_check_mng_mode(hw) ||
- e1000_check_phy_reset_block(hw))
- goto out;
- break;
default:
goto out;
}
ew32(RCTL, rctl & ~E1000_RCTL_EN);
/* flush and sleep below */
- /* can be netif_tx_disable when NETIF_F_LLTX is removed */
- netif_stop_queue(netdev);
+ netif_tx_disable(netdev);
/* disable transmits in the hardware */
tctl = er32(TCTL);
legacy_pba_adjust = true;
pba = E1000_PBA_30K;
break;
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
- pba = E1000_PBA_38K;
- break;
- case e1000_82573:
- pba = E1000_PBA_20K;
- break;
- case e1000_ich8lan:
- pba = E1000_PBA_8K;
case e1000_undefined:
case e1000_num_macs:
break;
/* if short on rx space, rx wins and must trump tx
* adjustment or use Early Receive if available */
- if (pba < min_rx_space) {
- switch (hw->mac_type) {
- case e1000_82573:
- /* ERT enabled in e1000_configure_rx */
- break;
- default:
- pba = min_rx_space;
- break;
- }
- }
+ if (pba < min_rx_space)
+ pba = min_rx_space;
}
}
/* if (adapter->hwflags & HWFLAGS_PHY_PWR_BIT) { */
if (hw->mac_type >= e1000_82544 &&
- hw->mac_type <= e1000_82547_rev_2 &&
hw->autoneg == 1 &&
hw->autoneg_advertised == ADVERTISE_1000_FULL) {
u32 ctrl = er32(CTRL);
e1000_reset_adaptive(hw);
e1000_phy_get_info(hw, &adapter->phy_info);
- if (!adapter->smart_power_down &&
- (hw->mac_type == e1000_82571 ||
- hw->mac_type == e1000_82572)) {
- u16 phy_data = 0;
- /* speed up time to link by disabling smart power down, ignore
- * the return value of this function because there is nothing
- * different we would do if it failed */
- e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
- &phy_data);
- phy_data &= ~IGP02E1000_PM_SPD;
- e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
- phy_data);
- }
-
e1000_release_manageability(adapter);
}
goto err_sw_init;
err = -EIO;
- /* Flash BAR mapping must happen after e1000_sw_init
- * because it depends on mac_type */
- if ((hw->mac_type == e1000_ich8lan) &&
- (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
- hw->flash_address = pci_ioremap_bar(pdev, 1);
- if (!hw->flash_address)
- goto err_flashmap;
- }
-
- if (e1000_check_phy_reset_block(hw))
- DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
if (hw->mac_type >= e1000_82543) {
netdev->features = NETIF_F_SG |
NETIF_F_HW_VLAN_TX |
NETIF_F_HW_VLAN_RX |
NETIF_F_HW_VLAN_FILTER;
- if (hw->mac_type == e1000_ich8lan)
- netdev->features &= ~NETIF_F_HW_VLAN_FILTER;
}
if ((hw->mac_type >= e1000_82544) &&
(hw->mac_type != e1000_82547))
netdev->features |= NETIF_F_TSO;
- if (hw->mac_type > e1000_82547_rev_2)
- netdev->features |= NETIF_F_TSO6;
if (pci_using_dac)
netdev->features |= NETIF_F_HIGHDMA;
netdev->vlan_features |= NETIF_F_TSO;
- netdev->vlan_features |= NETIF_F_TSO6;
netdev->vlan_features |= NETIF_F_HW_CSUM;
netdev->vlan_features |= NETIF_F_SG;
EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
eeprom_apme_mask = E1000_EEPROM_82544_APM;
break;
- case e1000_ich8lan:
- e1000_read_eeprom(hw,
- EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data);
- eeprom_apme_mask = E1000_EEPROM_ICH8_APME;
- break;
case e1000_82546:
case e1000_82546_rev_3:
- case e1000_82571:
- case e1000_80003es2lan:
if (er32(STATUS) & E1000_STATUS_FUNC_1){
e1000_read_eeprom(hw,
EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
break;
case E1000_DEV_ID_82546EB_FIBER:
case E1000_DEV_ID_82546GB_FIBER:
- case E1000_DEV_ID_82571EB_FIBER:
/* Wake events only supported on port A for dual fiber
* regardless of eeprom setting */
if (er32(STATUS) & E1000_STATUS_FUNC_1)
adapter->eeprom_wol = 0;
break;
case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
- case E1000_DEV_ID_82571EB_QUAD_COPPER:
- case E1000_DEV_ID_82571EB_QUAD_FIBER:
- case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
- case E1000_DEV_ID_82571PT_QUAD_COPPER:
/* if quad port adapter, disable WoL on all but port A */
if (global_quad_port_a != 0)
adapter->eeprom_wol = 0;
/* print bus type/speed/width info */
DPRINTK(PROBE, INFO, "(PCI%s:%s:%s) ",
- ((hw->bus_type == e1000_bus_type_pcix) ? "-X" :
- (hw->bus_type == e1000_bus_type_pci_express ? " Express":"")),
- ((hw->bus_speed == e1000_bus_speed_2500) ? "2.5Gb/s" :
- (hw->bus_speed == e1000_bus_speed_133) ? "133MHz" :
+ ((hw->bus_type == e1000_bus_type_pcix) ? "-X" : ""),
+ ((hw->bus_speed == e1000_bus_speed_133) ? "133MHz" :
(hw->bus_speed == e1000_bus_speed_120) ? "120MHz" :
(hw->bus_speed == e1000_bus_speed_100) ? "100MHz" :
(hw->bus_speed == e1000_bus_speed_66) ? "66MHz" : "33MHz"),
- ((hw->bus_width == e1000_bus_width_64) ? "64-bit" :
- (hw->bus_width == e1000_bus_width_pciex_4) ? "Width x4" :
- (hw->bus_width == e1000_bus_width_pciex_1) ? "Width x1" :
- "32-bit"));
+ ((hw->bus_width == e1000_bus_width_64) ? "64-bit" : "32-bit"));
printk("%pM\n", netdev->dev_addr);
- if (hw->bus_type == e1000_bus_type_pci_express) {
- DPRINTK(PROBE, WARNING, "This device (id %04x:%04x) will no "
- "longer be supported by this driver in the future.\n",
- pdev->vendor, pdev->device);
- DPRINTK(PROBE, WARNING, "please use the \"e1000e\" "
- "driver instead.\n");
- }
-
/* reset the hardware with the new settings */
e1000_reset(adapter);
- /* If the controller is 82573 and f/w is AMT, do not set
- * DRV_LOAD until the interface is up. For all other cases,
- * let the f/w know that the h/w is now under the control
- * of the driver. */
- if (hw->mac_type != e1000_82573 ||
- !e1000_check_mng_mode(hw))
- e1000_get_hw_control(adapter);
-
strcpy(netdev->name, "eth%d");
err = register_netdev(netdev);
if (err)
return 0;
err_register:
- e1000_release_hw_control(adapter);
err_eeprom:
- if (!e1000_check_phy_reset_block(hw))
- e1000_phy_hw_reset(hw);
+ e1000_phy_hw_reset(hw);
if (hw->flash_address)
iounmap(hw->flash_address);
-err_flashmap:
kfree(adapter->tx_ring);
kfree(adapter->rx_ring);
err_sw_init:
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ set_bit(__E1000_DOWN, &adapter->flags);
+ del_timer_sync(&adapter->tx_fifo_stall_timer);
+ del_timer_sync(&adapter->watchdog_timer);
+ del_timer_sync(&adapter->phy_info_timer);
+
cancel_work_sync(&adapter->reset_task);
e1000_release_manageability(adapter);
- /* Release control of h/w to f/w. If f/w is AMT enabled, this
- * would have already happened in close and is redundant. */
- e1000_release_hw_control(adapter);
-
unregister_netdev(netdev);
- if (!e1000_check_phy_reset_block(hw))
- e1000_phy_hw_reset(hw);
+ e1000_phy_hw_reset(hw);
kfree(adapter->tx_ring);
kfree(adapter->rx_ring);
e1000_update_mng_vlan(adapter);
}
- /* If AMT is enabled, let the firmware know that the network
- * interface is now open */
- if (hw->mac_type == e1000_82573 &&
- e1000_check_mng_mode(hw))
- e1000_get_hw_control(adapter);
-
/* before we allocate an interrupt, we must be ready to handle it.
* Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
* as soon as we call pci_request_irq, so we have to setup our
return E1000_SUCCESS;
err_req_irq:
- e1000_release_hw_control(adapter);
e1000_power_down_phy(adapter);
e1000_free_all_rx_resources(adapter);
err_setup_rx:
e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
}
- /* If AMT is enabled, let the firmware know that the network
- * interface is now closed */
- if (hw->mac_type == e1000_82573 &&
- e1000_check_mng_mode(hw))
- e1000_release_hw_control(adapter);
-
return 0;
}
{
u64 tdba;
struct e1000_hw *hw = &adapter->hw;
- u32 tdlen, tctl, tipg, tarc;
+ u32 tdlen, tctl, tipg;
u32 ipgr1, ipgr2;
/* Setup the HW Tx Head and Tail descriptor pointers */
}
/* Set the default values for the Tx Inter Packet Gap timer */
- if (hw->mac_type <= e1000_82547_rev_2 &&
- (hw->media_type == e1000_media_type_fiber ||
+ if ((hw->media_type == e1000_media_type_fiber ||
hw->media_type == e1000_media_type_internal_serdes))
tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
else
ipgr1 = DEFAULT_82542_TIPG_IPGR1;
ipgr2 = DEFAULT_82542_TIPG_IPGR2;
break;
- case e1000_80003es2lan:
- ipgr1 = DEFAULT_82543_TIPG_IPGR1;
- ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2;
- break;
default:
ipgr1 = DEFAULT_82543_TIPG_IPGR1;
ipgr2 = DEFAULT_82543_TIPG_IPGR2;
tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
(E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
- if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) {
- tarc = er32(TARC0);
- /* set the speed mode bit, we'll clear it if we're not at
- * gigabit link later */
- tarc |= (1 << 21);
- ew32(TARC0, tarc);
- } else if (hw->mac_type == e1000_80003es2lan) {
- tarc = er32(TARC0);
- tarc |= 1;
- ew32(TARC0, tarc);
- tarc = er32(TARC1);
- tarc |= 1;
- ew32(TARC1, tarc);
- }
-
e1000_config_collision_dist(hw);
/* Setup Transmit Descriptor Settings for eop descriptor */
static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
struct e1000_rx_ring *rxdr)
{
- struct e1000_hw *hw = &adapter->hw;
struct pci_dev *pdev = adapter->pdev;
int size, desc_len;
}
memset(rxdr->buffer_info, 0, size);
- if (hw->mac_type <= e1000_82547_rev_2)
- desc_len = sizeof(struct e1000_rx_desc);
- else
- desc_len = sizeof(union e1000_rx_desc_packet_split);
+ desc_len = sizeof(struct e1000_rx_desc);
/* Round up to nearest 4K */
{
u64 rdba;
struct e1000_hw *hw = &adapter->hw;
- u32 rdlen, rctl, rxcsum, ctrl_ext;
+ u32 rdlen, rctl, rxcsum;
if (adapter->netdev->mtu > ETH_DATA_LEN) {
rdlen = adapter->rx_ring[0].count *
ew32(ITR, 1000000000 / (adapter->itr * 256));
}
- if (hw->mac_type >= e1000_82571) {
- ctrl_ext = er32(CTRL_EXT);
- /* Reset delay timers after every interrupt */
- ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
- /* Auto-Mask interrupts upon ICR access */
- ctrl_ext |= E1000_CTRL_EXT_IAME;
- ew32(IAM, 0xffffffff);
- ew32(CTRL_EXT, ctrl_ext);
- E1000_WRITE_FLUSH();
- }
-
/* Setup the HW Rx Head and Tail Descriptor Pointers and
* the Base and Length of the Rx Descriptor Ring */
switch (adapter->num_rx_queues) {
e1000_rar_set(hw, hw->mac_addr, 0);
- /* With 82571 controllers, LAA may be overwritten (with the default)
- * due to controller reset from the other port. */
- if (hw->mac_type == e1000_82571) {
- /* activate the work around */
- hw->laa_is_present = 1;
-
- /* Hold a copy of the LAA in RAR[14] This is done so that
- * between the time RAR[0] gets clobbered and the time it
- * gets fixed (in e1000_watchdog), the actual LAA is in one
- * of the RARs and no incoming packets directed to this port
- * are dropped. Eventaully the LAA will be in RAR[0] and
- * RAR[14] */
- e1000_rar_set(hw, hw->mac_addr,
- E1000_RAR_ENTRIES - 1);
- }
-
if (hw->mac_type == e1000_82542_rev2_0)
e1000_leave_82542_rst(adapter);
u32 rctl;
u32 hash_value;
int i, rar_entries = E1000_RAR_ENTRIES;
- int mta_reg_count = (hw->mac_type == e1000_ich8lan) ?
- E1000_NUM_MTA_REGISTERS_ICH8LAN :
- E1000_NUM_MTA_REGISTERS;
+ int mta_reg_count = E1000_NUM_MTA_REGISTERS;
u32 *mcarray = kcalloc(mta_reg_count, sizeof(u32), GFP_ATOMIC);
if (!mcarray) {
return;
}
- if (hw->mac_type == e1000_ich8lan)
- rar_entries = E1000_RAR_ENTRIES_ICH8LAN;
-
- /* reserve RAR[14] for LAA over-write work-around */
- if (hw->mac_type == e1000_82571)
- rar_entries--;
-
/* Check for Promiscuous and All Multicast modes */
rctl = er32(RCTL);
rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
rctl &= ~E1000_RCTL_VFE;
} else {
- if (netdev->flags & IFF_ALLMULTI) {
+ if (netdev->flags & IFF_ALLMULTI)
rctl |= E1000_RCTL_MPE;
- } else {
+ else
rctl &= ~E1000_RCTL_MPE;
- }
- if (adapter->hw.mac_type != e1000_ich8lan)
- /* Enable VLAN filter if there is a VLAN */
- if (adapter->vlgrp)
- rctl |= E1000_RCTL_VFE;
+ /* Enable VLAN filter if there is a VLAN */
+ if (adapter->vlgrp)
+ rctl |= E1000_RCTL_VFE;
}
if (netdev->uc.count > rar_entries - 1) {
*
* RAR 0 is used for the station MAC adddress
* if there are not 14 addresses, go ahead and clear the filters
- * -- with 82571 controllers only 0-13 entries are filled here
*/
i = 1;
if (use_uc)
adapter->tx_fifo_head = 0;
atomic_set(&adapter->tx_fifo_stall, 0);
netif_wake_queue(netdev);
- } else {
+ } else if (!test_bit(__E1000_DOWN, &adapter->flags)) {
mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1);
}
}
}
+static bool e1000_has_link(struct e1000_adapter *adapter)
+{
+ struct e1000_hw *hw = &adapter->hw;
+ bool link_active = false;
+
+ /* get_link_status is set on LSC (link status) interrupt or
+ * rx sequence error interrupt. get_link_status will stay
+ * false until the e1000_check_for_link establishes link
+ * for copper adapters ONLY
+ */
+ switch (hw->media_type) {
+ case e1000_media_type_copper:
+ if (hw->get_link_status) {
+ e1000_check_for_link(hw);
+ link_active = !hw->get_link_status;
+ } else {
+ link_active = true;
+ }
+ break;
+ case e1000_media_type_fiber:
+ e1000_check_for_link(hw);
+ link_active = !!(er32(STATUS) & E1000_STATUS_LU);
+ break;
+ case e1000_media_type_internal_serdes:
+ e1000_check_for_link(hw);
+ link_active = hw->serdes_has_link;
+ break;
+ default:
+ break;
+ }
+
+ return link_active;
+}
+
/**
* e1000_watchdog - Timer Call-back
* @data: pointer to adapter cast into an unsigned long
struct net_device *netdev = adapter->netdev;
struct e1000_tx_ring *txdr = adapter->tx_ring;
u32 link, tctl;
- s32 ret_val;
-
- ret_val = e1000_check_for_link(hw);
- if ((ret_val == E1000_ERR_PHY) &&
- (hw->phy_type == e1000_phy_igp_3) &&
- (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
- /* See e1000_kumeran_lock_loss_workaround() */
- DPRINTK(LINK, INFO,
- "Gigabit has been disabled, downgrading speed\n");
- }
- if (hw->mac_type == e1000_82573) {
- e1000_enable_tx_pkt_filtering(hw);
- if (adapter->mng_vlan_id != hw->mng_cookie.vlan_id)
- e1000_update_mng_vlan(adapter);
- }
-
- if ((hw->media_type == e1000_media_type_internal_serdes) &&
- !(er32(TXCW) & E1000_TXCW_ANE))
- link = !hw->serdes_link_down;
- else
- link = er32(STATUS) & E1000_STATUS_LU;
+ link = e1000_has_link(adapter);
+ if ((netif_carrier_ok(netdev)) && link)
+ goto link_up;
if (link) {
if (!netif_carrier_ok(netdev)) {
u32 ctrl;
bool txb2b = true;
+ /* update snapshot of PHY registers on LSC */
e1000_get_speed_and_duplex(hw,
&adapter->link_speed,
&adapter->link_duplex);
case SPEED_10:
txb2b = false;
netdev->tx_queue_len = 10;
- adapter->tx_timeout_factor = 8;
+ adapter->tx_timeout_factor = 16;
break;
case SPEED_100:
txb2b = false;
break;
}
- if ((hw->mac_type == e1000_82571 ||
- hw->mac_type == e1000_82572) &&
- !txb2b) {
- u32 tarc0;
- tarc0 = er32(TARC0);
- tarc0 &= ~(1 << 21);
- ew32(TARC0, tarc0);
- }
-
- /* disable TSO for pcie and 10/100 speeds, to avoid
- * some hardware issues */
- if (!adapter->tso_force &&
- hw->bus_type == e1000_bus_type_pci_express){
- switch (adapter->link_speed) {
- case SPEED_10:
- case SPEED_100:
- DPRINTK(PROBE,INFO,
- "10/100 speed: disabling TSO\n");
- netdev->features &= ~NETIF_F_TSO;
- netdev->features &= ~NETIF_F_TSO6;
- break;
- case SPEED_1000:
- netdev->features |= NETIF_F_TSO;
- netdev->features |= NETIF_F_TSO6;
- break;
- default:
- /* oops */
- break;
- }
- }
-
- /* enable transmits in the hardware, need to do this
- * after setting TARC0 */
+ /* enable transmits in the hardware */
tctl = er32(TCTL);
tctl |= E1000_TCTL_EN;
ew32(TCTL, tctl);
netif_carrier_on(netdev);
- mod_timer(&adapter->phy_info_timer, round_jiffies(jiffies + 2 * HZ));
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
adapter->smartspeed = 0;
- } else {
- /* make sure the receive unit is started */
- if (hw->rx_needs_kicking) {
- u32 rctl = er32(RCTL);
- ew32(RCTL, rctl | E1000_RCTL_EN);
- }
}
} else {
if (netif_carrier_ok(netdev)) {
printk(KERN_INFO "e1000: %s NIC Link is Down\n",
netdev->name);
netif_carrier_off(netdev);
- mod_timer(&adapter->phy_info_timer, round_jiffies(jiffies + 2 * HZ));
-
- /* 80003ES2LAN workaround--
- * For packet buffer work-around on link down event;
- * disable receives in the ISR and
- * reset device here in the watchdog
- */
- if (hw->mac_type == e1000_80003es2lan)
- /* reset device */
- schedule_work(&adapter->reset_task);
+
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->phy_info_timer,
+ round_jiffies(jiffies + 2 * HZ));
}
e1000_smartspeed(adapter);
}
+link_up:
e1000_update_stats(adapter);
hw->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
/* Force detection of hung controller every watchdog period */
adapter->detect_tx_hung = true;
- /* With 82571 controllers, LAA may be overwritten due to controller
- * reset from the other port. Set the appropriate LAA in RAR[0] */
- if (hw->mac_type == e1000_82571 && hw->laa_is_present)
- e1000_rar_set(hw, hw->mac_addr, 0);
-
/* Reset the timer */
- mod_timer(&adapter->watchdog_timer, round_jiffies(jiffies + 2 * HZ));
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->watchdog_timer,
+ round_jiffies(jiffies + 2 * HZ));
}
enum latency_range {
/**
* e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
* Stores a new ITR value based on packets and byte
* counts during the last interrupt. The advantage of per interrupt
* computation is faster updates and more accurate ITR for the current
* while increasing bulk throughput.
* this functionality is controlled by the InterruptThrottleRate module
* parameter (see e1000_param.c)
- * @adapter: pointer to adapter
- * @itr_setting: current adapter->itr
- * @packets: the number of packets during this measurement interval
- * @bytes: the number of bytes during this measurement interval
**/
static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
u16 itr_setting, int packets, int bytes)
size -= 4;
buffer_info->length = size;
- buffer_info->dma = skb_shinfo(skb)->dma_head + offset;
+ /* set time_stamp *before* dma to help avoid a possible race */
buffer_info->time_stamp = jiffies;
+ buffer_info->dma = skb_shinfo(skb)->dma_head + offset;
buffer_info->next_to_watch = i;
len -= size;
* Avoid terminating buffers within evenly-aligned
* dwords. */
if (unlikely(adapter->pcix_82544 &&
- !((unsigned long)(frag->page+offset+size-1) & 4) &&
- size > 4))
+ !((unsigned long)(page_to_phys(frag->page) + offset
+ + size - 1) & 4) &&
+ size > 4))
size -= 4;
buffer_info->length = size;
- buffer_info->dma = map[f] + offset;
buffer_info->time_stamp = jiffies;
+ buffer_info->dma = map[f] + offset;
buffer_info->next_to_watch = i;
len -= size;
return 0;
}
-#define MINIMUM_DHCP_PACKET_SIZE 282
-static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
- struct sk_buff *skb)
-{
- struct e1000_hw *hw = &adapter->hw;
- u16 length, offset;
- if (vlan_tx_tag_present(skb)) {
- if (!((vlan_tx_tag_get(skb) == hw->mng_cookie.vlan_id) &&
- ( hw->mng_cookie.status &
- E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) )
- return 0;
- }
- if (skb->len > MINIMUM_DHCP_PACKET_SIZE) {
- struct ethhdr *eth = (struct ethhdr *)skb->data;
- if ((htons(ETH_P_IP) == eth->h_proto)) {
- const struct iphdr *ip =
- (struct iphdr *)((u8 *)skb->data+14);
- if (IPPROTO_UDP == ip->protocol) {
- struct udphdr *udp =
- (struct udphdr *)((u8 *)ip +
- (ip->ihl << 2));
- if (ntohs(udp->dest) == 67) {
- offset = (u8 *)udp + 8 - skb->data;
- length = skb->len - offset;
-
- return e1000_mng_write_dhcp_info(hw,
- (u8 *)udp + 8,
- length);
- }
- }
- }
- }
- return 0;
-}
-
static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
return NETDEV_TX_OK;
}
- /* 82571 and newer doesn't need the workaround that limited descriptor
- * length to 4kB */
- if (hw->mac_type >= e1000_82571)
- max_per_txd = 8192;
-
mss = skb_shinfo(skb)->gso_size;
/* The controller does a simple calculation to
* make sure there is enough room in the FIFO before
max_per_txd = min(mss << 2, max_per_txd);
max_txd_pwr = fls(max_per_txd) - 1;
- /* TSO Workaround for 82571/2/3 Controllers -- if skb->data
- * points to just header, pull a few bytes of payload from
- * frags into skb->data */
hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
if (skb->data_len && hdr_len == len) {
switch (hw->mac_type) {
if ((unsigned long)(skb_tail_pointer(skb) - 1) & 4)
break;
/* fall through */
- case e1000_82571:
- case e1000_82572:
- case e1000_82573:
- case e1000_ich8lan:
pull_size = min((unsigned int)4, skb->data_len);
if (!__pskb_pull_tail(skb, pull_size)) {
DPRINTK(DRV, ERR,
if (adapter->pcix_82544)
count += nr_frags;
-
- if (hw->tx_pkt_filtering &&
- (hw->mac_type == e1000_82573))
- e1000_transfer_dhcp_info(adapter, skb);
-
/* need: count + 2 desc gap to keep tail from touching
* head, otherwise try next time */
if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2)))
if (unlikely(hw->mac_type == e1000_82547)) {
if (unlikely(e1000_82547_fifo_workaround(adapter, skb))) {
netif_stop_queue(netdev);
- mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1);
+ if (!test_bit(__E1000_DOWN, &adapter->flags))
+ mod_timer(&adapter->tx_fifo_stall_timer,
+ jiffies + 1);
return NETDEV_TX_BUSY;
}
}
}
if (likely(tso)) {
- tx_ring->last_tx_tso = 1;
+ if (likely(hw->mac_type != e1000_82544))
+ tx_ring->last_tx_tso = 1;
tx_flags |= E1000_TX_FLAGS_TSO;
} else if (likely(e1000_tx_csum(adapter, tx_ring, skb)))
tx_flags |= E1000_TX_FLAGS_CSUM;
- /* Old method was to assume IPv4 packet by default if TSO was enabled.
- * 82571 hardware supports TSO capabilities for IPv6 as well...
- * no longer assume, we must. */
if (likely(skb->protocol == htons(ETH_P_IP)))
tx_flags |= E1000_TX_FLAGS_IPV4;
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
- u16 eeprom_data = 0;
if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) ||
(max_frame > MAX_JUMBO_FRAME_SIZE)) {
/* Adapter-specific max frame size limits. */
switch (hw->mac_type) {
case e1000_undefined ... e1000_82542_rev2_1:
- case e1000_ich8lan:
if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) {
DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n");
return -EINVAL;
}
break;
- case e1000_82573:
- /* Jumbo Frames not supported if:
- * - this is not an 82573L device
- * - ASPM is enabled in any way (0x1A bits 3:2) */
- e1000_read_eeprom(hw, EEPROM_INIT_3GIO_3, 1,
- &eeprom_data);
- if ((hw->device_id != E1000_DEV_ID_82573L) ||
- (eeprom_data & EEPROM_WORD1A_ASPM_MASK)) {
- if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) {
- DPRINTK(PROBE, ERR,
- "Jumbo Frames not supported.\n");
- return -EINVAL;
- }
- break;
- }
- /* ERT will be enabled later to enable wire speed receives */
-
- /* fall through to get support */
- case e1000_82571:
- case e1000_82572:
- case e1000_80003es2lan:
-#define MAX_STD_JUMBO_FRAME_SIZE 9234
- if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
- DPRINTK(PROBE, ERR, "MTU > 9216 not supported.\n");
- return -EINVAL;
- }
- break;
default:
/* Capable of supporting up to MAX_JUMBO_FRAME_SIZE limit. */
break;
}
+ while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
+ msleep(1);
+ /* e1000_down has a dependency on max_frame_size */
+ hw->max_frame_size = max_frame;
+ if (netif_running(netdev))
+ e1000_down(adapter);
+
/* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
* means we reserve 2 more, this pushes us to allocate from the next
* larger slab size.
(max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
+ printk(KERN_INFO "e1000: %s changing MTU from %d to %d\n",
+ netdev->name, netdev->mtu, new_mtu);
netdev->mtu = new_mtu;
- hw->max_frame_size = max_frame;
if (netif_running(netdev))
- e1000_reinit_locked(adapter);
+ e1000_up(adapter);
+ else
+ e1000_reset(adapter);
+
+ clear_bit(__E1000_RESETTING, &adapter->flags);
return 0;
}
adapter->stats.mprc += er32(MPRC);
adapter->stats.roc += er32(ROC);
- if (hw->mac_type != e1000_ich8lan) {
- adapter->stats.prc64 += er32(PRC64);
- adapter->stats.prc127 += er32(PRC127);
- adapter->stats.prc255 += er32(PRC255);
- adapter->stats.prc511 += er32(PRC511);
- adapter->stats.prc1023 += er32(PRC1023);
- adapter->stats.prc1522 += er32(PRC1522);
- }
+ adapter->stats.prc64 += er32(PRC64);
+ adapter->stats.prc127 += er32(PRC127);
+ adapter->stats.prc255 += er32(PRC255);
+ adapter->stats.prc511 += er32(PRC511);
+ adapter->stats.prc1023 += er32(PRC1023);
+ adapter->stats.prc1522 += er32(PRC1522);
adapter->stats.symerrs += er32(SYMERRS);
adapter->stats.mpc += er32(MPC);
adapter->stats.toth += er32(TOTH);
adapter->stats.tpr += er32(TPR);
- if (hw->mac_type != e1000_ich8lan) {
- adapter->stats.ptc64 += er32(PTC64);
- adapter->stats.ptc127 += er32(PTC127);
- adapter->stats.ptc255 += er32(PTC255);
- adapter->stats.ptc511 += er32(PTC511);
- adapter->stats.ptc1023 += er32(PTC1023);
- adapter->stats.ptc1522 += er32(PTC1522);
- }
+ adapter->stats.ptc64 += er32(PTC64);
+ adapter->stats.ptc127 += er32(PTC127);
+ adapter->stats.ptc255 += er32(PTC255);
+ adapter->stats.ptc511 += er32(PTC511);
+ adapter->stats.ptc1023 += er32(PTC1023);
+ adapter->stats.ptc1522 += er32(PTC1522);
adapter->stats.mptc += er32(MPTC);
adapter->stats.bptc += er32(BPTC);
adapter->stats.tsctc += er32(TSCTC);
adapter->stats.tsctfc += er32(TSCTFC);
}
- if (hw->mac_type > e1000_82547_rev_2) {
- adapter->stats.iac += er32(IAC);
- adapter->stats.icrxoc += er32(ICRXOC);
-
- if (hw->mac_type != e1000_ich8lan) {
- adapter->stats.icrxptc += er32(ICRXPTC);
- adapter->stats.icrxatc += er32(ICRXATC);
- adapter->stats.ictxptc += er32(ICTXPTC);
- adapter->stats.ictxatc += er32(ICTXATC);
- adapter->stats.ictxqec += er32(ICTXQEC);
- adapter->stats.ictxqmtc += er32(ICTXQMTC);
- adapter->stats.icrxdmtc += er32(ICRXDMTC);
- }
- }
/* Fill out the OS statistics structure */
adapter->net_stats.multicast = adapter->stats.mprc;
spin_unlock_irqrestore(&adapter->stats_lock, flags);
}
-/**
- * e1000_intr_msi - Interrupt Handler
- * @irq: interrupt number
- * @data: pointer to a network interface device structure
- **/
-
-static irqreturn_t e1000_intr_msi(int irq, void *data)
-{
- struct net_device *netdev = data;
- struct e1000_adapter *adapter = netdev_priv(netdev);
- struct e1000_hw *hw = &adapter->hw;
- u32 icr = er32(ICR);
-
- /* in NAPI mode read ICR disables interrupts using IAM */
-
- if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
- hw->get_link_status = 1;
- /* 80003ES2LAN workaround-- For packet buffer work-around on
- * link down event; disable receives here in the ISR and reset
- * adapter in watchdog */
- if (netif_carrier_ok(netdev) &&
- (hw->mac_type == e1000_80003es2lan)) {
- /* disable receives */
- u32 rctl = er32(RCTL);
- ew32(RCTL, rctl & ~E1000_RCTL_EN);
- }
- /* guard against interrupt when we're going down */
- if (!test_bit(__E1000_DOWN, &adapter->flags))
- mod_timer(&adapter->watchdog_timer, jiffies + 1);
- }
-
- if (likely(napi_schedule_prep(&adapter->napi))) {
- adapter->total_tx_bytes = 0;
- adapter->total_tx_packets = 0;
- adapter->total_rx_bytes = 0;
- adapter->total_rx_packets = 0;
- __napi_schedule(&adapter->napi);
- } else
- e1000_irq_enable(adapter);
-
- return IRQ_HANDLED;
-}
-
/**
* e1000_intr - Interrupt Handler
* @irq: interrupt number
struct net_device *netdev = data;
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- u32 rctl, icr = er32(ICR);
+ u32 icr = er32(ICR);
if (unlikely((!icr) || test_bit(__E1000_DOWN, &adapter->flags)))
return IRQ_NONE; /* Not our interrupt */
- /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is
- * not set, then the adapter didn't send an interrupt */
- if (unlikely(hw->mac_type >= e1000_82571 &&
- !(icr & E1000_ICR_INT_ASSERTED)))
- return IRQ_NONE;
-
- /* Interrupt Auto-Mask...upon reading ICR, interrupts are masked. No
- * need for the IMC write */
-
if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) {
hw->get_link_status = 1;
- /* 80003ES2LAN workaround--
- * For packet buffer work-around on link down event;
- * disable receives here in the ISR and
- * reset adapter in watchdog
- */
- if (netif_carrier_ok(netdev) &&
- (hw->mac_type == e1000_80003es2lan)) {
- /* disable receives */
- rctl = er32(RCTL);
- ew32(RCTL, rctl & ~E1000_RCTL_EN);
- }
/* guard against interrupt when we're going down */
if (!test_bit(__E1000_DOWN, &adapter->flags))
mod_timer(&adapter->watchdog_timer, jiffies + 1);
}
- if (unlikely(hw->mac_type < e1000_82571)) {
- /* disable interrupts, without the synchronize_irq bit */
- ew32(IMC, ~0);
- E1000_WRITE_FLUSH();
- }
+ /* disable interrupts, without the synchronize_irq bit */
+ ew32(IMC, ~0);
+ E1000_WRITE_FLUSH();
+
if (likely(napi_schedule_prep(&adapter->napi))) {
adapter->total_tx_bytes = 0;
adapter->total_tx_packets = 0;
static int e1000_clean(struct napi_struct *napi, int budget)
{
struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
- struct net_device *poll_dev = adapter->netdev;
- int tx_cleaned = 0, work_done = 0;
-
- adapter = netdev_priv(poll_dev);
+ int tx_clean_complete = 0, work_done = 0;
- tx_cleaned = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
+ tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
- adapter->clean_rx(adapter, &adapter->rx_ring[0],
- &work_done, budget);
+ adapter->clean_rx(adapter, &adapter->rx_ring[0], &work_done, budget);
- if (!tx_cleaned)
+ if (!tx_clean_complete)
work_done = budget;
/* If budget not fully consumed, exit the polling mode */
* sees the new next_to_clean.
*/
smp_mb();
- if (netif_queue_stopped(netdev)) {
+
+ if (netif_queue_stopped(netdev) &&
+ !(test_bit(__E1000_DOWN, &adapter->flags))) {
netif_wake_queue(netdev);
++adapter->restart_queue;
}
/* Detect a transmit hang in hardware, this serializes the
* check with the clearing of time_stamp and movement of i */
adapter->detect_tx_hung = false;
- if (tx_ring->buffer_info[i].time_stamp &&
- time_after(jiffies, tx_ring->buffer_info[i].time_stamp +
+ if (tx_ring->buffer_info[eop].time_stamp &&
+ time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
(adapter->tx_timeout_factor * HZ))
&& !(er32(STATUS) & E1000_STATUS_TXOFF)) {
readl(hw->hw_addr + tx_ring->tdt),
tx_ring->next_to_use,
tx_ring->next_to_clean,
- tx_ring->buffer_info[i].time_stamp,
+ tx_ring->buffer_info[eop].time_stamp,
eop,
jiffies,
eop_desc->upper.fields.status);
return;
}
/* TCP/UDP Checksum has not been calculated */
- if (hw->mac_type <= e1000_82547_rev_2) {
- if (!(status & E1000_RXD_STAT_TCPCS))
- return;
- } else {
- if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
- return;
- }
+ if (!(status & E1000_RXD_STAT_TCPCS))
+ return;
+
/* It must be a TCP or UDP packet with a valid checksum */
if (likely(status & E1000_RXD_STAT_TCPCS)) {
/* TCP checksum is good */
skb->ip_summed = CHECKSUM_UNNECESSARY;
- } else if (hw->mac_type > e1000_82547_rev_2) {
- /* IP fragment with UDP payload */
- /* Hardware complements the payload checksum, so we undo it
- * and then put the value in host order for further stack use.
- */
- __sum16 sum = (__force __sum16)htons(csum);
- skb->csum = csum_unfold(~sum);
- skb->ip_summed = CHECKSUM_COMPLETE;
}
adapter->hw_csum_good++;
}
pcix_set_mmrbc(adapter->pdev, mmrbc);
}
-s32 e1000_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value)
-{
- struct e1000_adapter *adapter = hw->back;
- u16 cap_offset;
-
- cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
- if (!cap_offset)
- return -E1000_ERR_CONFIG;
-
- pci_read_config_word(adapter->pdev, cap_offset + reg, value);
-
- return E1000_SUCCESS;
-}
-
void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value)
{
outl(value, port);
ctrl |= E1000_CTRL_VME;
ew32(CTRL, ctrl);
- if (adapter->hw.mac_type != e1000_ich8lan) {
- /* enable VLAN receive filtering */
- rctl = er32(RCTL);
- rctl &= ~E1000_RCTL_CFIEN;
- if (!(netdev->flags & IFF_PROMISC))
- rctl |= E1000_RCTL_VFE;
- ew32(RCTL, rctl);
- e1000_update_mng_vlan(adapter);
- }
+ /* enable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_CFIEN;
+ if (!(netdev->flags & IFF_PROMISC))
+ rctl |= E1000_RCTL_VFE;
+ ew32(RCTL, rctl);
+ e1000_update_mng_vlan(adapter);
} else {
/* disable VLAN tag insert/strip */
ctrl = er32(CTRL);
ctrl &= ~E1000_CTRL_VME;
ew32(CTRL, ctrl);
- if (adapter->hw.mac_type != e1000_ich8lan) {
- /* disable VLAN receive filtering */
- rctl = er32(RCTL);
- rctl &= ~E1000_RCTL_VFE;
- ew32(RCTL, rctl);
+ /* disable VLAN receive filtering */
+ rctl = er32(RCTL);
+ rctl &= ~E1000_RCTL_VFE;
+ ew32(RCTL, rctl);
- if (adapter->mng_vlan_id !=
- (u16)E1000_MNG_VLAN_NONE) {
- e1000_vlan_rx_kill_vid(netdev,
- adapter->mng_vlan_id);
- adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
- }
+ if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) {
+ e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
+ adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
}
}
if (!test_bit(__E1000_DOWN, &adapter->flags))
e1000_irq_enable(adapter);
- if ((hw->mng_cookie.status &
- E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
- (vid == adapter->mng_vlan_id)) {
- /* release control to f/w */
- e1000_release_hw_control(adapter);
- return;
- }
-
/* remove VID from filter table */
index = (vid >> 5) & 0x7F;
vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
}
if (hw->media_type == e1000_media_type_fiber ||
- hw->media_type == e1000_media_type_internal_serdes) {
+ hw->media_type == e1000_media_type_internal_serdes) {
/* keep the laser running in D3 */
ctrl_ext = er32(CTRL_EXT);
ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
ew32(CTRL_EXT, ctrl_ext);
}
- /* Allow time for pending master requests to run */
- e1000_disable_pciex_master(hw);
-
ew32(WUC, E1000_WUC_PME_EN);
ew32(WUFC, wufc);
} else {
if (adapter->en_mng_pt)
*enable_wake = true;
- if (hw->phy_type == e1000_phy_igp_3)
- e1000_phy_powerdown_workaround(hw);
-
if (netif_running(netdev))
e1000_free_irq(adapter);
- /* Release control of h/w to f/w. If f/w is AMT enabled, this
- * would have already happened in close and is redundant. */
- e1000_release_hw_control(adapter);
-
pci_disable_device(pdev);
return 0;
netif_device_attach(netdev);
- /* If the controller is 82573 and f/w is AMT, do not set
- * DRV_LOAD until the interface is up. For all other cases,
- * let the f/w know that the h/w is now under the control
- * of the driver. */
- if (hw->mac_type != e1000_82573 ||
- !e1000_check_mng_mode(hw))
- e1000_get_hw_control(adapter);
-
return 0;
}
#endif
/**
* e1000_io_error_detected - called when PCI error is detected
* @pdev: Pointer to PCI device
- * @state: The current pci conneection state
+ * @state: The current pci connection state
*
* This function is called after a PCI bus error affecting
* this device has been detected.
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct e1000_adapter *adapter = netdev_priv(netdev);
- struct e1000_hw *hw = &adapter->hw;
e1000_init_manageability(adapter);
}
netif_device_attach(netdev);
-
- /* If the controller is 82573 and f/w is AMT, do not set
- * DRV_LOAD until the interface is up. For all other cases,
- * let the f/w know that the h/w is now under the control
- * of the driver. */
- if (hw->mac_type != e1000_82573 ||
- !e1000_check_mng_mode(hw))
- e1000_get_hw_control(adapter);
-
}
/* e1000_main.c */
adapter->smart_power_down = opt.def;
}
}
- { /* Kumeran Lock Loss Workaround */
- opt = (struct e1000_option) {
- .type = enable_option,
- .name = "Kumeran Lock Loss Workaround",
- .err = "defaulting to Enabled",
- .def = OPTION_ENABLED
- };
-
- if (num_KumeranLockLoss > bd) {
- unsigned int kmrn_lock_loss = KumeranLockLoss[bd];
- e1000_validate_option(&kmrn_lock_loss, &opt, adapter);
- adapter->hw.kmrn_lock_loss_workaround_disabled = !kmrn_lock_loss;
- } else {
- adapter->hw.kmrn_lock_loss_workaround_disabled = !opt.def;
- }
- }
switch (adapter->hw.media_type) {
case e1000_media_type_fiber:
.p = dplx_list }}
};
- if (e1000_check_phy_reset_block(&adapter->hw)) {
- DPRINTK(PROBE, INFO,
- "Link active due to SoL/IDER Session. "
- "Speed/Duplex/AutoNeg parameter ignored.\n");
- return;
- }
if (num_Duplex > bd) {
dplx = Duplex[bd];
e1000_validate_option(&dplx, &opt, adapter);
goto err_pci_reg;
/* AER (Advanced Error Reporting) hooks */
- err = pci_enable_pcie_error_reporting(pdev);
- if (err) {
- dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed "
- "0x%x\n", err);
- /* non-fatal, continue */
- }
+ pci_enable_pcie_error_reporting(pdev);
pci_set_master(pdev);
/* PCI config space info */
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct e1000_adapter *adapter = netdev_priv(netdev);
- int err;
/*
* flush_scheduled work may reschedule our watchdog task, so
free_netdev(netdev);
/* AER disable */
- err = pci_disable_pcie_error_reporting(pdev);
- if (err)
- dev_err(&pdev->dev,
- "pci_disable_pcie_error_reporting failed 0x%x\n", err);
+ pci_disable_pcie_error_reporting(pdev);
pci_disable_device(pdev);
}
.ndo_poll_controller = ehea_netpoll,
#endif
.ndo_get_stats = ehea_get_stats,
- .ndo_change_mtu = eth_change_mtu,
.ndo_set_mac_address = ehea_set_mac_addr,
.ndo_validate_addr = eth_validate_addr,
.ndo_set_multicast_list = ehea_set_multicast_list,
}
if (ax->crcmode != CRC_MODE_SMACK && ax->crcauto) {
printk(KERN_INFO
- "mkiss: %s: Switchting to crc-smack\n",
+ "mkiss: %s: Switching to crc-smack\n",
ax->dev->name);
ax->crcmode = CRC_MODE_SMACK;
}
}
if (ax->crcmode != CRC_MODE_FLEX && ax->crcauto) {
printk(KERN_INFO
- "mkiss: %s: Switchting to crc-flexnet\n",
+ "mkiss: %s: Switching to crc-flexnet\n",
ax->dev->name);
ax->crcmode = CRC_MODE_FLEX;
}
wrfl();
}
-/**
- * igb_update_mc_addr_list - Update Multicast addresses
- * @hw: pointer to the HW structure
- * @mc_addr_list: array of multicast addresses to program
- * @mc_addr_count: number of multicast addresses to program
- *
- * Updates entire Multicast Table Array.
- * The caller must have a packed mc_addr_list of multicast addresses.
- **/
-void igb_update_mc_addr_list(struct e1000_hw *hw,
- u8 *mc_addr_list, u32 mc_addr_count)
-{
- u32 hash_value, hash_bit, hash_reg;
- int i;
-
- /* clear mta_shadow */
- memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
-
- /* update mta_shadow from mc_addr_list */
- for (i = 0; (u32) i < mc_addr_count; i++) {
- hash_value = igb_hash_mc_addr(hw, mc_addr_list);
-
- hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
- hash_bit = hash_value & 0x1F;
-
- hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
- mc_addr_list += (ETH_ALEN);
- }
-
- /* replace the entire MTA table */
- for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
- array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
- wrfl();
-}
-
/**
* igb_hash_mc_addr - Generate a multicast hash value
* @hw: pointer to the HW structure
* the multicast filter table array address and new table value. See
* igb_mta_set()
**/
-u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
+static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr)
{
u32 hash_value, hash_mask;
u8 bit_shift = 0;
return hash_value;
}
+/**
+ * igb_update_mc_addr_list - Update Multicast addresses
+ * @hw: pointer to the HW structure
+ * @mc_addr_list: array of multicast addresses to program
+ * @mc_addr_count: number of multicast addresses to program
+ *
+ * Updates entire Multicast Table Array.
+ * The caller must have a packed mc_addr_list of multicast addresses.
+ **/
+void igb_update_mc_addr_list(struct e1000_hw *hw,
+ u8 *mc_addr_list, u32 mc_addr_count)
+{
+ u32 hash_value, hash_bit, hash_reg;
+ int i;
+
+ /* clear mta_shadow */
+ memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow));
+
+ /* update mta_shadow from mc_addr_list */
+ for (i = 0; (u32) i < mc_addr_count; i++) {
+ hash_value = igb_hash_mc_addr(hw, mc_addr_list);
+
+ hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1);
+ hash_bit = hash_value & 0x1F;
+
+ hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit);
+ mc_addr_list += (ETH_ALEN);
+ }
+
+ /* replace the entire MTA table */
+ for (i = hw->mac.mta_reg_count - 1; i >= 0; i--)
+ array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]);
+ wrfl();
+}
+
/**
* igb_clear_hw_cntrs_base - Clear base hardware counters
* @hw: pointer to the HW structure
#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN 0x2
extern void e1000_init_function_pointers_82575(struct e1000_hw *hw);
-extern u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr);
#endif
if (err)
goto err_pci_reg;
- err = pci_enable_pcie_error_reporting(pdev);
- if (err) {
- dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed "
- "0x%x\n", err);
- /* non-fatal, continue */
- }
+ pci_enable_pcie_error_reporting(pdev);
pci_set_master(pdev);
pci_save_state(pdev);
struct net_device *netdev = pci_get_drvdata(pdev);
struct igb_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- int err;
/* flush_scheduled work may reschedule our watchdog task, so
* explicitly disable watchdog tasks from being rescheduled */
free_netdev(netdev);
- err = pci_disable_pcie_error_reporting(pdev);
- if (err)
- dev_err(&pdev->dev,
- "pci_disable_pcie_error_reporting failed 0x%x\n", err);
+ pci_disable_pcie_error_reporting(pdev);
pci_disable_device(pdev);
}
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
-#include <linux/kref.h>
#include <linux/usb.h>
#include <linux/device.h>
#include <linux/crc32.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
-#include <linux/kref.h>
#include <linux/usb.h>
#include <linux/device.h>
#include <linux/crc32.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
-#include <linux/kref.h>
#include <linux/usb.h>
#include <linux/device.h>
#include <linux/crc32.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
-#include <linux/kref.h>
#include <linux/usb.h>
#include <linux/device.h>
#include <linux/crc32.h>
#include <linux/etherdevice.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
+#include <linux/gpio.h>
#include <net/irda/irda.h>
#include <net/irda/irmod.h>
DCSR(si->txdma) |= DCSR_RUN;
}
+/*
+ * Set the IrDA communications mode.
+ */
+static void pxa_irda_set_mode(struct pxa_irda *si, int mode)
+{
+ if (si->pdata->transceiver_mode)
+ si->pdata->transceiver_mode(si->dev, mode);
+ else {
+ if (gpio_is_valid(si->pdata->gpio_pwdown))
+ gpio_set_value(si->pdata->gpio_pwdown,
+ !(mode & IR_OFF) ^
+ !si->pdata->gpio_pwdown_inverted);
+ pxa2xx_transceiver_mode(si->dev, mode);
+ }
+}
+
/*
* Set the IrDA communications speed.
*/
pxa_irda_disable_clk(si);
/* set board transceiver to SIR mode */
- si->pdata->transceiver_mode(si->dev, IR_SIRMODE);
+ pxa_irda_set_mode(si, IR_SIRMODE);
/* enable the STUART clock */
pxa_irda_enable_sirclk(si);
ICCR0 = 0;
/* set board transceiver to FIR mode */
- si->pdata->transceiver_mode(si->dev, IR_FIRMODE);
+ pxa_irda_set_mode(si, IR_FIRMODE);
/* enable the FICP clock */
pxa_irda_enable_firclk(si);
local_irq_restore(flags);
/* power off board transceiver */
- si->pdata->transceiver_mode(si->dev, IR_OFF);
+ pxa_irda_set_mode(si, IR_OFF);
printk(KERN_DEBUG "pxa_ir: irda shutdown\n");
}
if (err)
goto err_mem_5;
- if (si->pdata->startup)
+ if (gpio_is_valid(si->pdata->gpio_pwdown)) {
+ err = gpio_request(si->pdata->gpio_pwdown, "IrDA switch");
+ if (err)
+ goto err_startup;
+ err = gpio_direction_output(si->pdata->gpio_pwdown,
+ !si->pdata->gpio_pwdown_inverted);
+ if (err) {
+ gpio_free(si->pdata->gpio_pwdown);
+ goto err_startup;
+ }
+ }
+
+ if (si->pdata->startup) {
err = si->pdata->startup(si->dev);
- if (err)
- goto err_startup;
+ if (err)
+ goto err_startup;
+ }
+
+ if (gpio_is_valid(si->pdata->gpio_pwdown) && si->pdata->startup)
+ dev_warn(si->dev, "gpio_pwdown and startup() both defined!\n");
dev->netdev_ops = &pxa_irda_netdev_ops;
if (dev) {
struct pxa_irda *si = netdev_priv(dev);
unregister_netdev(dev);
+ if (gpio_is_valid(si->pdata->gpio_pwdown))
+ gpio_free(si->pdata->gpio_pwdown);
if (si->pdata->shutdown)
si->pdata->shutdown(si->dev);
kfree(si->tx_buff.head);
cnx->remote_lp);
} else {
memcpy(&cnx->cap_ack_event, event,
- sizeof(&cnx->cap_ack_event));
+ sizeof(cnx->cap_ack_event));
cnx->state |= VETH_STATE_GOTCAPACK;
veth_kick_statemachine(cnx);
}
enum ixgbe_fc_mode last_lfc_mode;
/* Interrupt Throttle Rate */
- u32 itr_setting;
+ u32 rx_itr_setting;
+ u32 tx_itr_setting;
u16 eitr_low;
u16 eitr_high;
struct ixgbe_hw_stats stats;
/* Interrupt Throttle Rate */
- u32 eitr_param;
+ u32 rx_eitr_param;
+ u32 tx_eitr_param;
unsigned long state;
u64 tx_busy;
#endif /* CONFIG_DCB */
default:
hw_dbg(hw, "Flow control param set incorrectly\n");
- ret_val = -IXGBE_ERR_CONFIG;
+ ret_val = IXGBE_ERR_CONFIG;
goto out;
break;
}
/**
* ixgbe_update_uc_addr_list_generic - Updates MAC list of secondary addresses
* @hw: pointer to hardware structure
- * @addr_list: the list of new addresses
- * @addr_count: number of addresses
- * @next: iterator function to walk the address list
+ * @uc_list: the list of new addresses
*
* The given list replaces any existing list. Clears the secondary addrs from
* receive address registers. Uses unused receive address registers for the
#endif /* CONFIG_DCB */
default:
hw_dbg(hw, "Flow control param set incorrectly\n");
- ret_val = -IXGBE_ERR_CONFIG;
+ ret_val = IXGBE_ERR_CONFIG;
goto out;
break;
}
s32 ret_val = 0;
ixgbe_link_speed speed;
u32 pcs_anadv_reg, pcs_lpab_reg, linkstat;
+ u32 links2, anlp1_reg, autoc_reg, links;
bool link_up;
/*
* AN should have completed when the cable was plugged in.
* Look for reasons to bail out. Bail out if:
* - FC autoneg is disabled, or if
- * - we don't have multispeed fiber, or if
- * - we're not running at 1G, or if
- * - link is not up, or if
- * - link is up but AN did not complete, or if
- * - link is up and AN completed but timed out
+ * - link is not up.
*
- * Since we're being called from an LSC, link is already know to be up.
+ * Since we're being called from an LSC, link is already known to be up.
* So use link_up_wait_to_complete=false.
*/
hw->mac.ops.check_link(hw, &speed, &link_up, false);
- linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
-
- if (hw->fc.disable_fc_autoneg ||
- !hw->phy.multispeed_fiber ||
- (speed != IXGBE_LINK_SPEED_1GB_FULL) ||
- !link_up ||
- ((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
- ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) {
+
+ if (hw->fc.disable_fc_autoneg || (!link_up)) {
hw->fc.fc_was_autonegged = false;
hw->fc.current_mode = hw->fc.requested_mode;
- hw_dbg(hw, "Autoneg FC was skipped.\n");
goto out;
}
+ /*
+ * On backplane, bail out if
+ * - backplane autoneg was not completed, or if
+ * - link partner is not AN enabled
+ */
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
+ links = IXGBE_READ_REG(hw, IXGBE_LINKS);
+ links2 = IXGBE_READ_REG(hw, IXGBE_LINKS2);
+ if (((links & IXGBE_LINKS_KX_AN_COMP) == 0) ||
+ ((links2 & IXGBE_LINKS2_AN_SUPPORTED) == 0)) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+ }
+
+ /*
+ * On multispeed fiber at 1g, bail out if
+ * - link is up but AN did not complete, or if
+ * - link is up and AN completed but timed out
+ */
+ if (hw->phy.multispeed_fiber && (speed == IXGBE_LINK_SPEED_1GB_FULL)) {
+ linkstat = IXGBE_READ_REG(hw, IXGBE_PCS1GLSTA);
+ if (((linkstat & IXGBE_PCS1GLSTA_AN_COMPLETE) == 0) ||
+ ((linkstat & IXGBE_PCS1GLSTA_AN_TIMED_OUT) == 1)) {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+ }
+
/*
* Read the AN advertisement and LP ability registers and resolve
* local flow control settings accordingly
*/
- pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
- pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
- if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
- (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) {
+ if ((speed == IXGBE_LINK_SPEED_1GB_FULL) &&
+ (hw->phy.media_type != ixgbe_media_type_backplane)) {
+ pcs_anadv_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+ pcs_lpab_reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANLP);
+ if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_full) {
+ hw->fc.current_mode = ixgbe_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control=RX PAUSE only\n");
+ }
+ } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+ } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
+ !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
+ (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
+ }
+ }
+
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
/*
- * Now we need to check if the user selected Rx ONLY
- * of pause frames. In this case, we had to advertise
- * FULL flow control because we could not advertise RX
- * ONLY. Hence, we must now check to see if we need to
- * turn OFF the TRANSMISSION of PAUSE frames.
+ * Read the 10g AN autoc and LP ability registers and resolve
+ * local flow control settings accordingly
*/
- if (hw->fc.requested_mode == ixgbe_fc_full) {
- hw->fc.current_mode = ixgbe_fc_full;
- hw_dbg(hw, "Flow Control = FULL.\n");
- } else {
+ autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ anlp1_reg = IXGBE_READ_REG(hw, IXGBE_ANLP1);
+
+ if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_full) {
+ hw->fc.current_mode = ixgbe_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control=RX PAUSE only\n");
+ }
+ } else if (!(autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
+ (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) {
+ hw->fc.current_mode = ixgbe_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+ } else if ((autoc_reg & IXGBE_AUTOC_SYM_PAUSE) &&
+ (autoc_reg & IXGBE_AUTOC_ASM_PAUSE) &&
+ !(anlp1_reg & IXGBE_ANLP1_SYM_PAUSE) &&
+ (anlp1_reg & IXGBE_ANLP1_ASM_PAUSE)) {
hw->fc.current_mode = ixgbe_fc_rx_pause;
hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
}
- } else if (!(pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
- (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
- (pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
- (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
- hw->fc.current_mode = ixgbe_fc_tx_pause;
- hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
- } else if ((pcs_anadv_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
- (pcs_anadv_reg & IXGBE_PCS1GANA_ASM_PAUSE) &&
- !(pcs_lpab_reg & IXGBE_PCS1GANA_SYM_PAUSE) &&
- (pcs_lpab_reg & IXGBE_PCS1GANA_ASM_PAUSE)) {
- hw->fc.current_mode = ixgbe_fc_rx_pause;
- hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
- } else {
- hw->fc.current_mode = ixgbe_fc_none;
- hw_dbg(hw, "Flow Control = NONE.\n");
}
-
/* Record that current_mode is the result of a successful autoneg */
hw->fc.fc_was_autonegged = true;
#endif /* CONFIG_DCB */
default:
hw_dbg(hw, "Flow control param set incorrectly\n");
- ret_val = -IXGBE_ERR_CONFIG;
+ ret_val = IXGBE_ERR_CONFIG;
goto out;
break;
}
IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
- /* Enable and restart autoneg to inform the link partner */
- reg |= IXGBE_PCS1GLCTL_AN_ENABLE | IXGBE_PCS1GLCTL_AN_RESTART;
-
/* Disable AN timeout */
if (hw->fc.strict_ieee)
reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
+ /*
+ * Set up the 10G flow control advertisement registers so the HW
+ * can do fc autoneg once the cable is plugged in. If we end up
+ * using 1g instead, this is harmless.
+ */
+ reg = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+
+ /*
+ * The possible values of fc.requested_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: Invalid.
+ */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ reg &= ~(IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ reg |= (IXGBE_AUTOC_ASM_PAUSE);
+ reg &= ~(IXGBE_AUTOC_SYM_PAUSE);
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ reg |= (IXGBE_AUTOC_SYM_PAUSE | IXGBE_AUTOC_ASM_PAUSE);
+ break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+ /*
+ * AUTOC restart handles negotiation of 1G and 10G. There is
+ * no need to set the PCS1GCTL register.
+ */
+ reg |= IXGBE_AUTOC_AN_RESTART;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg);
+ hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
+
out:
return ret_val;
}
while (timeout) {
if (ixgbe_get_eeprom_semaphore(hw))
- return -IXGBE_ERR_SWFW_SYNC;
+ return IXGBE_ERR_SWFW_SYNC;
gssr = IXGBE_READ_REG(hw, IXGBE_GSSR);
if (!(gssr & (fwmask | swmask)))
if (!timeout) {
hw_dbg(hw, "Driver can't access resource, GSSR timeout.\n");
- return -IXGBE_ERR_SWFW_SYNC;
+ return IXGBE_ERR_SWFW_SYNC;
}
gssr |= swmask;
{"tx_packets", IXGBE_STAT(net_stats.tx_packets)},
{"rx_bytes", IXGBE_STAT(net_stats.rx_bytes)},
{"tx_bytes", IXGBE_STAT(net_stats.tx_bytes)},
+ {"rx_pkts_nic", IXGBE_STAT(stats.gprc)},
+ {"tx_pkts_nic", IXGBE_STAT(stats.gptc)},
+ {"rx_bytes_nic", IXGBE_STAT(stats.gorc)},
+ {"tx_bytes_nic", IXGBE_STAT(stats.gotc)},
{"lsc_int", IXGBE_STAT(lsc_int)},
{"tx_busy", IXGBE_STAT(tx_busy)},
{"non_eop_descs", IXGBE_STAT(non_eop_descs)},
ec->tx_max_coalesced_frames_irq = adapter->tx_ring[0].work_limit;
/* only valid if in constant ITR mode */
- switch (adapter->itr_setting) {
+ switch (adapter->rx_itr_setting) {
case 0:
/* throttling disabled */
ec->rx_coalesce_usecs = 0;
break;
default:
/* fixed interrupt rate mode */
- ec->rx_coalesce_usecs = 1000000/adapter->eitr_param;
+ ec->rx_coalesce_usecs = 1000000/adapter->rx_eitr_param;
break;
}
+
+ /* only valid if in constant ITR mode */
+ switch (adapter->tx_itr_setting) {
+ case 0:
+ /* throttling disabled */
+ ec->tx_coalesce_usecs = 0;
+ break;
+ case 1:
+ /* dynamic ITR mode */
+ ec->tx_coalesce_usecs = 1;
+ break;
+ default:
+ ec->tx_coalesce_usecs = 1000000/adapter->tx_eitr_param;
+ break;
+ }
+
return 0;
}
struct ixgbe_q_vector *q_vector;
int i;
+ /*
+ * don't accept tx specific changes if we've got mixed RxTx vectors
+ * test and jump out here if needed before changing the rx numbers
+ */
+ if ((1000000/ec->tx_coalesce_usecs) != adapter->tx_eitr_param &&
+ adapter->q_vector[0]->txr_count && adapter->q_vector[0]->rxr_count)
+ return -EINVAL;
+
if (ec->tx_max_coalesced_frames_irq)
adapter->tx_ring[0].work_limit = ec->tx_max_coalesced_frames_irq;
return -EINVAL;
/* store the value in ints/second */
- adapter->eitr_param = 1000000/ec->rx_coalesce_usecs;
+ adapter->rx_eitr_param = 1000000/ec->rx_coalesce_usecs;
/* static value of interrupt rate */
- adapter->itr_setting = adapter->eitr_param;
+ adapter->rx_itr_setting = adapter->rx_eitr_param;
/* clear the lower bit as its used for dynamic state */
- adapter->itr_setting &= ~1;
+ adapter->rx_itr_setting &= ~1;
} else if (ec->rx_coalesce_usecs == 1) {
/* 1 means dynamic mode */
- adapter->eitr_param = 20000;
- adapter->itr_setting = 1;
+ adapter->rx_eitr_param = 20000;
+ adapter->rx_itr_setting = 1;
} else {
/*
* any other value means disable eitr, which is best
* served by setting the interrupt rate very high
*/
if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED)
- adapter->eitr_param = IXGBE_MAX_RSC_INT_RATE;
+ adapter->rx_eitr_param = IXGBE_MAX_RSC_INT_RATE;
else
- adapter->eitr_param = IXGBE_MAX_INT_RATE;
- adapter->itr_setting = 0;
+ adapter->rx_eitr_param = IXGBE_MAX_INT_RATE;
+ adapter->rx_itr_setting = 0;
+ }
+
+ if (ec->tx_coalesce_usecs > 1) {
+ /* check the limits */
+ if ((1000000/ec->tx_coalesce_usecs > IXGBE_MAX_INT_RATE) ||
+ (1000000/ec->tx_coalesce_usecs < IXGBE_MIN_INT_RATE))
+ return -EINVAL;
+
+ /* store the value in ints/second */
+ adapter->tx_eitr_param = 1000000/ec->tx_coalesce_usecs;
+
+ /* static value of interrupt rate */
+ adapter->tx_itr_setting = adapter->tx_eitr_param;
+
+ /* clear the lower bit as its used for dynamic state */
+ adapter->tx_itr_setting &= ~1;
+ } else if (ec->tx_coalesce_usecs == 1) {
+ /* 1 means dynamic mode */
+ adapter->tx_eitr_param = 10000;
+ adapter->tx_itr_setting = 1;
+ } else {
+ adapter->tx_eitr_param = IXGBE_MAX_INT_RATE;
+ adapter->tx_itr_setting = 0;
}
/* MSI/MSIx Interrupt Mode */
for (i = 0; i < num_vectors; i++) {
q_vector = adapter->q_vector[i];
if (q_vector->txr_count && !q_vector->rxr_count)
- /* tx vector gets half the rate */
- q_vector->eitr = (adapter->eitr_param >> 1);
+ /* tx only */
+ q_vector->eitr = adapter->tx_eitr_param;
else
/* rx only or mixed */
- q_vector->eitr = adapter->eitr_param;
+ q_vector->eitr = adapter->rx_eitr_param;
ixgbe_write_eitr(q_vector);
}
/* Legacy Interrupt Mode */
} else {
q_vector = adapter->q_vector[0];
- q_vector->eitr = adapter->eitr_param;
+ q_vector->eitr = adapter->rx_eitr_param;
ixgbe_write_eitr(q_vector);
}
static const char ixgbe_driver_string[] =
"Intel(R) 10 Gigabit PCI Express Network Driver";
-#define DRV_VERSION "2.0.37-k2"
+#define DRV_VERSION "2.0.44-k2"
const char ixgbe_driver_version[] = DRV_VERSION;
static char ixgbe_copyright[] = "Copyright (c) 1999-2009 Intel Corporation.";
r_idx + 1);
}
- /* if this is a tx only vector halve the interrupt rate */
if (q_vector->txr_count && !q_vector->rxr_count)
- q_vector->eitr = (adapter->eitr_param >> 1);
+ /* tx only */
+ q_vector->eitr = adapter->tx_eitr_param;
else if (q_vector->rxr_count)
- /* rx only */
- q_vector->eitr = adapter->eitr_param;
+ /* rx or mixed */
+ q_vector->eitr = adapter->rx_eitr_param;
ixgbe_write_eitr(q_vector);
}
/* If all Rx work done, exit the polling mode */
if (work_done < budget) {
napi_complete(napi);
- if (adapter->itr_setting & 1)
+ if (adapter->rx_itr_setting & 1)
ixgbe_set_itr_msix(q_vector);
if (!test_bit(__IXGBE_DOWN, &adapter->state))
ixgbe_irq_enable_queues(adapter,
/* If all Rx work done, exit the polling mode */
if (work_done < budget) {
napi_complete(napi);
- if (adapter->itr_setting & 1)
+ if (adapter->rx_itr_setting & 1)
ixgbe_set_itr_msix(q_vector);
if (!test_bit(__IXGBE_DOWN, &adapter->state))
ixgbe_irq_enable_queues(adapter,
if (!ixgbe_clean_tx_irq(q_vector, tx_ring))
work_done = budget;
- /* If all Rx work done, exit the polling mode */
+ /* If all Tx work done, exit the polling mode */
if (work_done < budget) {
napi_complete(napi);
- if (adapter->itr_setting & 1)
+ if (adapter->tx_itr_setting & 1)
ixgbe_set_itr_msix(q_vector);
if (!test_bit(__IXGBE_DOWN, &adapter->state))
ixgbe_irq_enable_queues(adapter, ((u64)1 << q_vector->v_idx));
struct ixgbe_hw *hw = &adapter->hw;
IXGBE_WRITE_REG(hw, IXGBE_EITR(0),
- EITR_INTS_PER_SEC_TO_REG(adapter->eitr_param));
+ EITR_INTS_PER_SEC_TO_REG(adapter->rx_eitr_param));
ixgbe_set_ivar(adapter, 0, 0, 0);
ixgbe_set_ivar(adapter, 1, 0, 0);
IXGBE_WRITE_REG(hw, IXGBE_TDT(j), 0);
adapter->tx_ring[i].head = IXGBE_TDH(j);
adapter->tx_ring[i].tail = IXGBE_TDT(j);
- /* Disable Tx Head Writeback RO bit, since this hoses
+ /*
+ * Disable Tx Head Writeback RO bit, since this hoses
* bookkeeping if things aren't delivered in order.
*/
- txctrl = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL(j));
+ switch (hw->mac.type) {
+ case ixgbe_mac_82598EB:
+ txctrl = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL(j));
+ break;
+ case ixgbe_mac_82599EB:
+ default:
+ txctrl = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL_82599(j));
+ break;
+ }
txctrl &= ~IXGBE_DCA_TXCTRL_TX_WB_RO_EN;
- IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL(j), txctrl);
+ switch (hw->mac.type) {
+ case ixgbe_mac_82598EB:
+ IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL(j), txctrl);
+ break;
+ case ixgbe_mac_82599EB:
+ default:
+ IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL_82599(j), txctrl);
+ break;
+ }
}
if (hw->mac.type == ixgbe_mac_82599EB) {
/* We enable 8 traffic classes, DCB only */
return mrqc;
}
+/**
+ * ixgbe_configure_rscctl - enable RSC for the indicated ring
+ * @adapter: address of board private structure
+ * @index: index of ring to set
+ * @rx_buf_len: rx buffer length
+ **/
+static void ixgbe_configure_rscctl(struct ixgbe_adapter *adapter, int index,
+ int rx_buf_len)
+{
+ struct ixgbe_ring *rx_ring;
+ struct ixgbe_hw *hw = &adapter->hw;
+ int j;
+ u32 rscctrl;
+
+ rx_ring = &adapter->rx_ring[index];
+ j = rx_ring->reg_idx;
+ rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j));
+ rscctrl |= IXGBE_RSCCTL_RSCEN;
+ /*
+ * we must limit the number of descriptors so that the
+ * total size of max desc * buf_len is not greater
+ * than 65535
+ */
+ if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
+#if (MAX_SKB_FRAGS > 16)
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
+#elif (MAX_SKB_FRAGS > 8)
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
+#elif (MAX_SKB_FRAGS > 4)
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
+#else
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_1;
+#endif
+ } else {
+ if (rx_buf_len < IXGBE_RXBUFFER_4096)
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
+ else if (rx_buf_len < IXGBE_RXBUFFER_8192)
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
+ else
+ rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
+ }
+ IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(j), rscctrl);
+}
+
/**
* ixgbe_configure_rx - Configure 8259x Receive Unit after Reset
* @adapter: board private structure
u32 fctrl, hlreg0;
u32 reta = 0, mrqc = 0;
u32 rdrxctl;
- u32 rscctrl;
int rx_buf_len;
/* Decide whether to use packet split mode or not */
if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) {
/* Enable 82599 HW-RSC */
- for (i = 0; i < adapter->num_rx_queues; i++) {
- rx_ring = &adapter->rx_ring[i];
- j = rx_ring->reg_idx;
- rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j));
- rscctrl |= IXGBE_RSCCTL_RSCEN;
- /*
- * we must limit the number of descriptors so that the
- * total size of max desc * buf_len is not greater
- * than 65535
- */
- if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) {
-#if (MAX_SKB_FRAGS > 16)
- rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
-#elif (MAX_SKB_FRAGS > 8)
- rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
-#elif (MAX_SKB_FRAGS > 4)
- rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
-#else
- rscctrl |= IXGBE_RSCCTL_MAXDESC_1;
-#endif
- } else {
- if (rx_buf_len < IXGBE_RXBUFFER_4096)
- rscctrl |= IXGBE_RSCCTL_MAXDESC_16;
- else if (rx_buf_len < IXGBE_RXBUFFER_8192)
- rscctrl |= IXGBE_RSCCTL_MAXDESC_8;
- else
- rscctrl |= IXGBE_RSCCTL_MAXDESC_4;
- }
- IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(j), rscctrl);
- }
+ for (i = 0; i < adapter->num_rx_queues; i++)
+ ixgbe_configure_rscctl(adapter, i, rx_buf_len);
+
/* Disable RSC for ACK packets */
IXGBE_WRITE_REG(hw, IXGBE_RSCDBU,
(IXGBE_RSCDBU_RSCACKDIS | IXGBE_READ_REG(hw, IXGBE_RSCDBU)));
ixgbe_napi_disable_all(adapter);
+ clear_bit(__IXGBE_SFP_MODULE_NOT_FOUND, &adapter->state);
+ del_timer_sync(&adapter->sfp_timer);
del_timer_sync(&adapter->watchdog_timer);
cancel_work_sync(&adapter->watchdog_task);
/* If budget not fully consumed, exit the polling mode */
if (work_done < budget) {
napi_complete(napi);
- if (adapter->itr_setting & 1)
+ if (adapter->rx_itr_setting & 1)
ixgbe_set_itr(adapter);
if (!test_bit(__IXGBE_DOWN, &adapter->state))
ixgbe_irq_enable_queues(adapter, IXGBE_EIMS_RTX_QUEUE);
if (!q_vector)
goto err_out;
q_vector->adapter = adapter;
- q_vector->eitr = adapter->eitr_param;
+ if (q_vector->txr_count && !q_vector->rxr_count)
+ q_vector->eitr = adapter->tx_eitr_param;
+ else
+ q_vector->eitr = adapter->rx_eitr_param;
q_vector->v_idx = q_idx;
netif_napi_add(adapter->netdev, &q_vector->napi, (*poll), 64);
adapter->q_vector[q_idx] = q_vector;
hw->fc.disable_fc_autoneg = false;
/* enable itr by default in dynamic mode */
- adapter->itr_setting = 1;
- adapter->eitr_param = 20000;
+ adapter->rx_itr_setting = 1;
+ adapter->rx_eitr_param = 20000;
+ adapter->tx_itr_setting = 1;
+ adapter->tx_eitr_param = 10000;
/* set defaults for eitr in MegaBytes */
adapter->eitr_low = 10;
/* 82598 hardware only has a 32 bit counter in the high register */
if (hw->mac.type == ixgbe_mac_82599EB) {
+ u64 tmp;
adapter->stats.gorc += IXGBE_READ_REG(hw, IXGBE_GORCL);
- IXGBE_READ_REG(hw, IXGBE_GORCH); /* to clear */
+ tmp = IXGBE_READ_REG(hw, IXGBE_GORCH) & 0xF; /* 4 high bits of GORC */
+ adapter->stats.gorc += (tmp << 32);
adapter->stats.gotc += IXGBE_READ_REG(hw, IXGBE_GOTCL);
- IXGBE_READ_REG(hw, IXGBE_GOTCH); /* to clear */
+ tmp = IXGBE_READ_REG(hw, IXGBE_GOTCH) & 0xF; /* 4 high bits of GOTC */
+ adapter->stats.gotc += (tmp << 32);
adapter->stats.tor += IXGBE_READ_REG(hw, IXGBE_TORL);
IXGBE_READ_REG(hw, IXGBE_TORH); /* to clear */
adapter->stats.lxonrxc += IXGBE_READ_REG(hw, IXGBE_LXONRXCNT);
/* Right now, we support IPv4 only */
struct ixgbe_atr_input atr_input;
struct tcphdr *th;
- struct udphdr *uh;
struct iphdr *iph = ip_hdr(skb);
struct ethhdr *eth = (struct ethhdr *)skb->data;
u16 vlan_id, src_port, dst_port, flex_bytes;
dst_port = th->dest;
l4type |= IXGBE_ATR_L4TYPE_TCP;
/* l4type IPv4 type is 0, no need to assign */
- } else if(iph->protocol == IPPROTO_UDP) {
- uh = udp_hdr(skb);
- src_port = uh->source;
- dst_port = uh->dest;
- l4type |= IXGBE_ATR_L4TYPE_UDP;
- /* l4type IPv4 type is 0, no need to assign */
} else {
/* Unsupported L4 header, just bail here */
return;
goto err_pci_reg;
}
- err = pci_enable_pcie_error_reporting(pdev);
- if (err) {
- dev_err(&pdev->dev, "pci_enable_pcie_error_reporting failed "
- "0x%x\n", err);
- /* non-fatal, continue */
- }
+ pci_enable_pcie_error_reporting(pdev);
pci_set_master(pdev);
pci_save_state(pdev);
{
struct net_device *netdev = pci_get_drvdata(pdev);
struct ixgbe_adapter *adapter = netdev_priv(netdev);
- int err;
set_bit(__IXGBE_DOWN, &adapter->state);
/* clear the module not found bit to make sure the worker won't
free_netdev(netdev);
- err = pci_disable_pcie_error_reporting(pdev);
- if (err)
- dev_err(&pdev->dev,
- "pci_disable_pcie_error_reporting failed 0x%x\n", err);
+ pci_disable_pcie_error_reporting(pdev);
pci_disable_device(pdev);
}
#define IXGBE_AUTOC_KX4_SUPP 0x80000000
#define IXGBE_AUTOC_KX_SUPP 0x40000000
#define IXGBE_AUTOC_PAUSE 0x30000000
+#define IXGBE_AUTOC_ASM_PAUSE 0x20000000
+#define IXGBE_AUTOC_SYM_PAUSE 0x10000000
#define IXGBE_AUTOC_RF 0x08000000
#define IXGBE_AUTOC_PD_TMR 0x06000000
#define IXGBE_AUTOC_AN_RX_LOOSE 0x01000000
#define IXGBE_LINK_UP_TIME 90 /* 9.0 Seconds */
#define IXGBE_AUTO_NEG_TIME 45 /* 4.5 Seconds */
+#define IXGBE_LINKS2_AN_SUPPORTED 0x00000040
+
/* PCS1GLSTA Bit Masks */
#define IXGBE_PCS1GLSTA_LINK_OK 1
#define IXGBE_PCS1GLSTA_SYNK_OK 0x10
#define IXGBE_PCS1GLCTL_AN_ENABLE 0x10000
#define IXGBE_PCS1GLCTL_AN_RESTART 0x20000
+/* ANLP1 Bit Masks */
+#define IXGBE_ANLP1_PAUSE 0x0C00
+#define IXGBE_ANLP1_SYM_PAUSE 0x0400
+#define IXGBE_ANLP1_ASM_PAUSE 0x0800
+
/* SW Semaphore Register bitmasks */
#define IXGBE_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
#define IXGBE_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
--- /dev/null
+/**
+ * drivers/net/ks8851_mll.c
+ * Copyright (c) 2009 Micrel Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/**
+ * Supports:
+ * KS8851 16bit MLL chip from Micrel Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/cache.h>
+#include <linux/crc32.h>
+#include <linux/mii.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+
+#define DRV_NAME "ks8851_mll"
+
+static u8 KS_DEFAULT_MAC_ADDRESS[] = { 0x00, 0x10, 0xA1, 0x86, 0x95, 0x11 };
+#define MAX_RECV_FRAMES 32
+#define MAX_BUF_SIZE 2048
+#define TX_BUF_SIZE 2000
+#define RX_BUF_SIZE 2000
+
+#define KS_CCR 0x08
+#define CCR_EEPROM (1 << 9)
+#define CCR_SPI (1 << 8)
+#define CCR_8BIT (1 << 7)
+#define CCR_16BIT (1 << 6)
+#define CCR_32BIT (1 << 5)
+#define CCR_SHARED (1 << 4)
+#define CCR_32PIN (1 << 0)
+
+/* MAC address registers */
+#define KS_MARL 0x10
+#define KS_MARM 0x12
+#define KS_MARH 0x14
+
+#define KS_OBCR 0x20
+#define OBCR_ODS_16MA (1 << 6)
+
+#define KS_EEPCR 0x22
+#define EEPCR_EESA (1 << 4)
+#define EEPCR_EESB (1 << 3)
+#define EEPCR_EEDO (1 << 2)
+#define EEPCR_EESCK (1 << 1)
+#define EEPCR_EECS (1 << 0)
+
+#define KS_MBIR 0x24
+#define MBIR_TXMBF (1 << 12)
+#define MBIR_TXMBFA (1 << 11)
+#define MBIR_RXMBF (1 << 4)
+#define MBIR_RXMBFA (1 << 3)
+
+#define KS_GRR 0x26
+#define GRR_QMU (1 << 1)
+#define GRR_GSR (1 << 0)
+
+#define KS_WFCR 0x2A
+#define WFCR_MPRXE (1 << 7)
+#define WFCR_WF3E (1 << 3)
+#define WFCR_WF2E (1 << 2)
+#define WFCR_WF1E (1 << 1)
+#define WFCR_WF0E (1 << 0)
+
+#define KS_WF0CRC0 0x30
+#define KS_WF0CRC1 0x32
+#define KS_WF0BM0 0x34
+#define KS_WF0BM1 0x36
+#define KS_WF0BM2 0x38
+#define KS_WF0BM3 0x3A
+
+#define KS_WF1CRC0 0x40
+#define KS_WF1CRC1 0x42
+#define KS_WF1BM0 0x44
+#define KS_WF1BM1 0x46
+#define KS_WF1BM2 0x48
+#define KS_WF1BM3 0x4A
+
+#define KS_WF2CRC0 0x50
+#define KS_WF2CRC1 0x52
+#define KS_WF2BM0 0x54
+#define KS_WF2BM1 0x56
+#define KS_WF2BM2 0x58
+#define KS_WF2BM3 0x5A
+
+#define KS_WF3CRC0 0x60
+#define KS_WF3CRC1 0x62
+#define KS_WF3BM0 0x64
+#define KS_WF3BM1 0x66
+#define KS_WF3BM2 0x68
+#define KS_WF3BM3 0x6A
+
+#define KS_TXCR 0x70
+#define TXCR_TCGICMP (1 << 8)
+#define TXCR_TCGUDP (1 << 7)
+#define TXCR_TCGTCP (1 << 6)
+#define TXCR_TCGIP (1 << 5)
+#define TXCR_FTXQ (1 << 4)
+#define TXCR_TXFCE (1 << 3)
+#define TXCR_TXPE (1 << 2)
+#define TXCR_TXCRC (1 << 1)
+#define TXCR_TXE (1 << 0)
+
+#define KS_TXSR 0x72
+#define TXSR_TXLC (1 << 13)
+#define TXSR_TXMC (1 << 12)
+#define TXSR_TXFID_MASK (0x3f << 0)
+#define TXSR_TXFID_SHIFT (0)
+#define TXSR_TXFID_GET(_v) (((_v) >> 0) & 0x3f)
+
+
+#define KS_RXCR1 0x74
+#define RXCR1_FRXQ (1 << 15)
+#define RXCR1_RXUDPFCC (1 << 14)
+#define RXCR1_RXTCPFCC (1 << 13)
+#define RXCR1_RXIPFCC (1 << 12)
+#define RXCR1_RXPAFMA (1 << 11)
+#define RXCR1_RXFCE (1 << 10)
+#define RXCR1_RXEFE (1 << 9)
+#define RXCR1_RXMAFMA (1 << 8)
+#define RXCR1_RXBE (1 << 7)
+#define RXCR1_RXME (1 << 6)
+#define RXCR1_RXUE (1 << 5)
+#define RXCR1_RXAE (1 << 4)
+#define RXCR1_RXINVF (1 << 1)
+#define RXCR1_RXE (1 << 0)
+#define RXCR1_FILTER_MASK (RXCR1_RXINVF | RXCR1_RXAE | \
+ RXCR1_RXMAFMA | RXCR1_RXPAFMA)
+
+#define KS_RXCR2 0x76
+#define RXCR2_SRDBL_MASK (0x7 << 5)
+#define RXCR2_SRDBL_SHIFT (5)
+#define RXCR2_SRDBL_4B (0x0 << 5)
+#define RXCR2_SRDBL_8B (0x1 << 5)
+#define RXCR2_SRDBL_16B (0x2 << 5)
+#define RXCR2_SRDBL_32B (0x3 << 5)
+/* #define RXCR2_SRDBL_FRAME (0x4 << 5) */
+#define RXCR2_IUFFP (1 << 4)
+#define RXCR2_RXIUFCEZ (1 << 3)
+#define RXCR2_UDPLFE (1 << 2)
+#define RXCR2_RXICMPFCC (1 << 1)
+#define RXCR2_RXSAF (1 << 0)
+
+#define KS_TXMIR 0x78
+
+#define KS_RXFHSR 0x7C
+#define RXFSHR_RXFV (1 << 15)
+#define RXFSHR_RXICMPFCS (1 << 13)
+#define RXFSHR_RXIPFCS (1 << 12)
+#define RXFSHR_RXTCPFCS (1 << 11)
+#define RXFSHR_RXUDPFCS (1 << 10)
+#define RXFSHR_RXBF (1 << 7)
+#define RXFSHR_RXMF (1 << 6)
+#define RXFSHR_RXUF (1 << 5)
+#define RXFSHR_RXMR (1 << 4)
+#define RXFSHR_RXFT (1 << 3)
+#define RXFSHR_RXFTL (1 << 2)
+#define RXFSHR_RXRF (1 << 1)
+#define RXFSHR_RXCE (1 << 0)
+#define RXFSHR_ERR (RXFSHR_RXCE | RXFSHR_RXRF |\
+ RXFSHR_RXFTL | RXFSHR_RXMR |\
+ RXFSHR_RXICMPFCS | RXFSHR_RXIPFCS |\
+ RXFSHR_RXTCPFCS)
+#define KS_RXFHBCR 0x7E
+#define RXFHBCR_CNT_MASK 0x0FFF
+
+#define KS_TXQCR 0x80
+#define TXQCR_AETFE (1 << 2)
+#define TXQCR_TXQMAM (1 << 1)
+#define TXQCR_METFE (1 << 0)
+
+#define KS_RXQCR 0x82
+#define RXQCR_RXDTTS (1 << 12)
+#define RXQCR_RXDBCTS (1 << 11)
+#define RXQCR_RXFCTS (1 << 10)
+#define RXQCR_RXIPHTOE (1 << 9)
+#define RXQCR_RXDTTE (1 << 7)
+#define RXQCR_RXDBCTE (1 << 6)
+#define RXQCR_RXFCTE (1 << 5)
+#define RXQCR_ADRFE (1 << 4)
+#define RXQCR_SDA (1 << 3)
+#define RXQCR_RRXEF (1 << 0)
+#define RXQCR_CMD_CNTL (RXQCR_RXFCTE|RXQCR_ADRFE)
+
+#define KS_TXFDPR 0x84
+#define TXFDPR_TXFPAI (1 << 14)
+#define TXFDPR_TXFP_MASK (0x7ff << 0)
+#define TXFDPR_TXFP_SHIFT (0)
+
+#define KS_RXFDPR 0x86
+#define RXFDPR_RXFPAI (1 << 14)
+
+#define KS_RXDTTR 0x8C
+#define KS_RXDBCTR 0x8E
+
+#define KS_IER 0x90
+#define KS_ISR 0x92
+#define IRQ_LCI (1 << 15)
+#define IRQ_TXI (1 << 14)
+#define IRQ_RXI (1 << 13)
+#define IRQ_RXOI (1 << 11)
+#define IRQ_TXPSI (1 << 9)
+#define IRQ_RXPSI (1 << 8)
+#define IRQ_TXSAI (1 << 6)
+#define IRQ_RXWFDI (1 << 5)
+#define IRQ_RXMPDI (1 << 4)
+#define IRQ_LDI (1 << 3)
+#define IRQ_EDI (1 << 2)
+#define IRQ_SPIBEI (1 << 1)
+#define IRQ_DEDI (1 << 0)
+
+#define KS_RXFCTR 0x9C
+#define RXFCTR_THRESHOLD_MASK 0x00FF
+
+#define KS_RXFC 0x9D
+#define RXFCTR_RXFC_MASK (0xff << 8)
+#define RXFCTR_RXFC_SHIFT (8)
+#define RXFCTR_RXFC_GET(_v) (((_v) >> 8) & 0xff)
+#define RXFCTR_RXFCT_MASK (0xff << 0)
+#define RXFCTR_RXFCT_SHIFT (0)
+
+#define KS_TXNTFSR 0x9E
+
+#define KS_MAHTR0 0xA0
+#define KS_MAHTR1 0xA2
+#define KS_MAHTR2 0xA4
+#define KS_MAHTR3 0xA6
+
+#define KS_FCLWR 0xB0
+#define KS_FCHWR 0xB2
+#define KS_FCOWR 0xB4
+
+#define KS_CIDER 0xC0
+#define CIDER_ID 0x8870
+#define CIDER_REV_MASK (0x7 << 1)
+#define CIDER_REV_SHIFT (1)
+#define CIDER_REV_GET(_v) (((_v) >> 1) & 0x7)
+
+#define KS_CGCR 0xC6
+#define KS_IACR 0xC8
+#define IACR_RDEN (1 << 12)
+#define IACR_TSEL_MASK (0x3 << 10)
+#define IACR_TSEL_SHIFT (10)
+#define IACR_TSEL_MIB (0x3 << 10)
+#define IACR_ADDR_MASK (0x1f << 0)
+#define IACR_ADDR_SHIFT (0)
+
+#define KS_IADLR 0xD0
+#define KS_IAHDR 0xD2
+
+#define KS_PMECR 0xD4
+#define PMECR_PME_DELAY (1 << 14)
+#define PMECR_PME_POL (1 << 12)
+#define PMECR_WOL_WAKEUP (1 << 11)
+#define PMECR_WOL_MAGICPKT (1 << 10)
+#define PMECR_WOL_LINKUP (1 << 9)
+#define PMECR_WOL_ENERGY (1 << 8)
+#define PMECR_AUTO_WAKE_EN (1 << 7)
+#define PMECR_WAKEUP_NORMAL (1 << 6)
+#define PMECR_WKEVT_MASK (0xf << 2)
+#define PMECR_WKEVT_SHIFT (2)
+#define PMECR_WKEVT_GET(_v) (((_v) >> 2) & 0xf)
+#define PMECR_WKEVT_ENERGY (0x1 << 2)
+#define PMECR_WKEVT_LINK (0x2 << 2)
+#define PMECR_WKEVT_MAGICPKT (0x4 << 2)
+#define PMECR_WKEVT_FRAME (0x8 << 2)
+#define PMECR_PM_MASK (0x3 << 0)
+#define PMECR_PM_SHIFT (0)
+#define PMECR_PM_NORMAL (0x0 << 0)
+#define PMECR_PM_ENERGY (0x1 << 0)
+#define PMECR_PM_SOFTDOWN (0x2 << 0)
+#define PMECR_PM_POWERSAVE (0x3 << 0)
+
+/* Standard MII PHY data */
+#define KS_P1MBCR 0xE4
+#define P1MBCR_FORCE_FDX (1 << 8)
+
+#define KS_P1MBSR 0xE6
+#define P1MBSR_AN_COMPLETE (1 << 5)
+#define P1MBSR_AN_CAPABLE (1 << 3)
+#define P1MBSR_LINK_UP (1 << 2)
+
+#define KS_PHY1ILR 0xE8
+#define KS_PHY1IHR 0xEA
+#define KS_P1ANAR 0xEC
+#define KS_P1ANLPR 0xEE
+
+#define KS_P1SCLMD 0xF4
+#define P1SCLMD_LEDOFF (1 << 15)
+#define P1SCLMD_TXIDS (1 << 14)
+#define P1SCLMD_RESTARTAN (1 << 13)
+#define P1SCLMD_DISAUTOMDIX (1 << 10)
+#define P1SCLMD_FORCEMDIX (1 << 9)
+#define P1SCLMD_AUTONEGEN (1 << 7)
+#define P1SCLMD_FORCE100 (1 << 6)
+#define P1SCLMD_FORCEFDX (1 << 5)
+#define P1SCLMD_ADV_FLOW (1 << 4)
+#define P1SCLMD_ADV_100BT_FDX (1 << 3)
+#define P1SCLMD_ADV_100BT_HDX (1 << 2)
+#define P1SCLMD_ADV_10BT_FDX (1 << 1)
+#define P1SCLMD_ADV_10BT_HDX (1 << 0)
+
+#define KS_P1CR 0xF6
+#define P1CR_HP_MDIX (1 << 15)
+#define P1CR_REV_POL (1 << 13)
+#define P1CR_OP_100M (1 << 10)
+#define P1CR_OP_FDX (1 << 9)
+#define P1CR_OP_MDI (1 << 7)
+#define P1CR_AN_DONE (1 << 6)
+#define P1CR_LINK_GOOD (1 << 5)
+#define P1CR_PNTR_FLOW (1 << 4)
+#define P1CR_PNTR_100BT_FDX (1 << 3)
+#define P1CR_PNTR_100BT_HDX (1 << 2)
+#define P1CR_PNTR_10BT_FDX (1 << 1)
+#define P1CR_PNTR_10BT_HDX (1 << 0)
+
+/* TX Frame control */
+
+#define TXFR_TXIC (1 << 15)
+#define TXFR_TXFID_MASK (0x3f << 0)
+#define TXFR_TXFID_SHIFT (0)
+
+#define KS_P1SR 0xF8
+#define P1SR_HP_MDIX (1 << 15)
+#define P1SR_REV_POL (1 << 13)
+#define P1SR_OP_100M (1 << 10)
+#define P1SR_OP_FDX (1 << 9)
+#define P1SR_OP_MDI (1 << 7)
+#define P1SR_AN_DONE (1 << 6)
+#define P1SR_LINK_GOOD (1 << 5)
+#define P1SR_PNTR_FLOW (1 << 4)
+#define P1SR_PNTR_100BT_FDX (1 << 3)
+#define P1SR_PNTR_100BT_HDX (1 << 2)
+#define P1SR_PNTR_10BT_FDX (1 << 1)
+#define P1SR_PNTR_10BT_HDX (1 << 0)
+
+#define ENUM_BUS_NONE 0
+#define ENUM_BUS_8BIT 1
+#define ENUM_BUS_16BIT 2
+#define ENUM_BUS_32BIT 3
+
+#define MAX_MCAST_LST 32
+#define HW_MCAST_SIZE 8
+#define MAC_ADDR_LEN 6
+
+/**
+ * union ks_tx_hdr - tx header data
+ * @txb: The header as bytes
+ * @txw: The header as 16bit, little-endian words
+ *
+ * A dual representation of the tx header data to allow
+ * access to individual bytes, and to allow 16bit accesses
+ * with 16bit alignment.
+ */
+union ks_tx_hdr {
+ u8 txb[4];
+ __le16 txw[2];
+};
+
+/**
+ * struct ks_net - KS8851 driver private data
+ * @net_device : The network device we're bound to
+ * @hw_addr : start address of data register.
+ * @hw_addr_cmd : start address of command register.
+ * @txh : temporaly buffer to save status/length.
+ * @lock : Lock to ensure that the device is not accessed when busy.
+ * @pdev : Pointer to platform device.
+ * @mii : The MII state information for the mii calls.
+ * @frame_head_info : frame header information for multi-pkt rx.
+ * @statelock : Lock on this structure for tx list.
+ * @msg_enable : The message flags controlling driver output (see ethtool).
+ * @frame_cnt : number of frames received.
+ * @bus_width : i/o bus width.
+ * @irq : irq number assigned to this device.
+ * @rc_rxqcr : Cached copy of KS_RXQCR.
+ * @rc_txcr : Cached copy of KS_TXCR.
+ * @rc_ier : Cached copy of KS_IER.
+ * @sharedbus : Multipex(addr and data bus) mode indicator.
+ * @cmd_reg_cache : command register cached.
+ * @cmd_reg_cache_int : command register cached. Used in the irq handler.
+ * @promiscuous : promiscuous mode indicator.
+ * @all_mcast : mutlicast indicator.
+ * @mcast_lst_size : size of multicast list.
+ * @mcast_lst : multicast list.
+ * @mcast_bits : multicast enabed.
+ * @mac_addr : MAC address assigned to this device.
+ * @fid : frame id.
+ * @extra_byte : number of extra byte prepended rx pkt.
+ * @enabled : indicator this device works.
+ *
+ * The @lock ensures that the chip is protected when certain operations are
+ * in progress. When the read or write packet transfer is in progress, most
+ * of the chip registers are not accessible until the transfer is finished and
+ * the DMA has been de-asserted.
+ *
+ * The @statelock is used to protect information in the structure which may
+ * need to be accessed via several sources, such as the network driver layer
+ * or one of the work queues.
+ *
+ */
+
+/* Receive multiplex framer header info */
+struct type_frame_head {
+ u16 sts; /* Frame status */
+ u16 len; /* Byte count */
+};
+
+struct ks_net {
+ struct net_device *netdev;
+ void __iomem *hw_addr;
+ void __iomem *hw_addr_cmd;
+ union ks_tx_hdr txh ____cacheline_aligned;
+ struct mutex lock; /* spinlock to be interrupt safe */
+ struct platform_device *pdev;
+ struct mii_if_info mii;
+ struct type_frame_head *frame_head_info;
+ spinlock_t statelock;
+ u32 msg_enable;
+ u32 frame_cnt;
+ int bus_width;
+ int irq;
+
+ u16 rc_rxqcr;
+ u16 rc_txcr;
+ u16 rc_ier;
+ u16 sharedbus;
+ u16 cmd_reg_cache;
+ u16 cmd_reg_cache_int;
+ u16 promiscuous;
+ u16 all_mcast;
+ u16 mcast_lst_size;
+ u8 mcast_lst[MAX_MCAST_LST][MAC_ADDR_LEN];
+ u8 mcast_bits[HW_MCAST_SIZE];
+ u8 mac_addr[6];
+ u8 fid;
+ u8 extra_byte;
+ u8 enabled;
+};
+
+static int msg_enable;
+
+#define ks_info(_ks, _msg...) dev_info(&(_ks)->pdev->dev, _msg)
+#define ks_warn(_ks, _msg...) dev_warn(&(_ks)->pdev->dev, _msg)
+#define ks_dbg(_ks, _msg...) dev_dbg(&(_ks)->pdev->dev, _msg)
+#define ks_err(_ks, _msg...) dev_err(&(_ks)->pdev->dev, _msg)
+
+#define BE3 0x8000 /* Byte Enable 3 */
+#define BE2 0x4000 /* Byte Enable 2 */
+#define BE1 0x2000 /* Byte Enable 1 */
+#define BE0 0x1000 /* Byte Enable 0 */
+
+/**
+ * register read/write calls.
+ *
+ * All these calls issue transactions to access the chip's registers. They
+ * all require that the necessary lock is held to prevent accesses when the
+ * chip is busy transfering packet data (RX/TX FIFO accesses).
+ */
+
+/**
+ * ks_rdreg8 - read 8 bit register from device
+ * @ks : The chip information
+ * @offset: The register address
+ *
+ * Read a 8bit register from the chip, returning the result
+ */
+static u8 ks_rdreg8(struct ks_net *ks, int offset)
+{
+ u16 data;
+ u8 shift_bit = offset & 0x03;
+ u8 shift_data = (offset & 1) << 3;
+ ks->cmd_reg_cache = (u16) offset | (u16)(BE0 << shift_bit);
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ data = ioread16(ks->hw_addr);
+ return (u8)(data >> shift_data);
+}
+
+/**
+ * ks_rdreg16 - read 16 bit register from device
+ * @ks : The chip information
+ * @offset: The register address
+ *
+ * Read a 16bit register from the chip, returning the result
+ */
+
+static u16 ks_rdreg16(struct ks_net *ks, int offset)
+{
+ ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ return ioread16(ks->hw_addr);
+}
+
+/**
+ * ks_wrreg8 - write 8bit register value to chip
+ * @ks: The chip information
+ * @offset: The register address
+ * @value: The value to write
+ *
+ */
+static void ks_wrreg8(struct ks_net *ks, int offset, u8 value)
+{
+ u8 shift_bit = (offset & 0x03);
+ u16 value_write = (u16)(value << ((offset & 1) << 3));
+ ks->cmd_reg_cache = (u16)offset | (BE0 << shift_bit);
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ iowrite16(value_write, ks->hw_addr);
+}
+
+/**
+ * ks_wrreg16 - write 16bit register value to chip
+ * @ks: The chip information
+ * @offset: The register address
+ * @value: The value to write
+ *
+ */
+
+static void ks_wrreg16(struct ks_net *ks, int offset, u16 value)
+{
+ ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+ iowrite16(value, ks->hw_addr);
+}
+
+/**
+ * ks_inblk - read a block of data from QMU. This is called after sudo DMA mode enabled.
+ * @ks: The chip state
+ * @wptr: buffer address to save data
+ * @len: length in byte to read
+ *
+ */
+static inline void ks_inblk(struct ks_net *ks, u16 *wptr, u32 len)
+{
+ len >>= 1;
+ while (len--)
+ *wptr++ = (u16)ioread16(ks->hw_addr);
+}
+
+/**
+ * ks_outblk - write data to QMU. This is called after sudo DMA mode enabled.
+ * @ks: The chip information
+ * @wptr: buffer address
+ * @len: length in byte to write
+ *
+ */
+static inline void ks_outblk(struct ks_net *ks, u16 *wptr, u32 len)
+{
+ len >>= 1;
+ while (len--)
+ iowrite16(*wptr++, ks->hw_addr);
+}
+
+/**
+ * ks_tx_fifo_space - return the available hardware buffer size.
+ * @ks: The chip information
+ *
+ */
+static inline u16 ks_tx_fifo_space(struct ks_net *ks)
+{
+ return ks_rdreg16(ks, KS_TXMIR) & 0x1fff;
+}
+
+/**
+ * ks_save_cmd_reg - save the command register from the cache.
+ * @ks: The chip information
+ *
+ */
+static inline void ks_save_cmd_reg(struct ks_net *ks)
+{
+ /*ks8851 MLL has a bug to read back the command register.
+ * So rely on software to save the content of command register.
+ */
+ ks->cmd_reg_cache_int = ks->cmd_reg_cache;
+}
+
+/**
+ * ks_restore_cmd_reg - restore the command register from the cache and
+ * write to hardware register.
+ * @ks: The chip information
+ *
+ */
+static inline void ks_restore_cmd_reg(struct ks_net *ks)
+{
+ ks->cmd_reg_cache = ks->cmd_reg_cache_int;
+ iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
+}
+
+/**
+ * ks_set_powermode - set power mode of the device
+ * @ks: The chip information
+ * @pwrmode: The power mode value to write to KS_PMECR.
+ *
+ * Change the power mode of the chip.
+ */
+static void ks_set_powermode(struct ks_net *ks, unsigned pwrmode)
+{
+ unsigned pmecr;
+
+ if (netif_msg_hw(ks))
+ ks_dbg(ks, "setting power mode %d\n", pwrmode);
+
+ ks_rdreg16(ks, KS_GRR);
+ pmecr = ks_rdreg16(ks, KS_PMECR);
+ pmecr &= ~PMECR_PM_MASK;
+ pmecr |= pwrmode;
+
+ ks_wrreg16(ks, KS_PMECR, pmecr);
+}
+
+/**
+ * ks_read_config - read chip configuration of bus width.
+ * @ks: The chip information
+ *
+ */
+static void ks_read_config(struct ks_net *ks)
+{
+ u16 reg_data = 0;
+
+ /* Regardless of bus width, 8 bit read should always work.*/
+ reg_data = ks_rdreg8(ks, KS_CCR) & 0x00FF;
+ reg_data |= ks_rdreg8(ks, KS_CCR+1) << 8;
+
+ /* addr/data bus are multiplexed */
+ ks->sharedbus = (reg_data & CCR_SHARED) == CCR_SHARED;
+
+ /* There are garbage data when reading data from QMU,
+ depending on bus-width.
+ */
+
+ if (reg_data & CCR_8BIT) {
+ ks->bus_width = ENUM_BUS_8BIT;
+ ks->extra_byte = 1;
+ } else if (reg_data & CCR_16BIT) {
+ ks->bus_width = ENUM_BUS_16BIT;
+ ks->extra_byte = 2;
+ } else {
+ ks->bus_width = ENUM_BUS_32BIT;
+ ks->extra_byte = 4;
+ }
+}
+
+/**
+ * ks_soft_reset - issue one of the soft reset to the device
+ * @ks: The device state.
+ * @op: The bit(s) to set in the GRR
+ *
+ * Issue the relevant soft-reset command to the device's GRR register
+ * specified by @op.
+ *
+ * Note, the delays are in there as a caution to ensure that the reset
+ * has time to take effect and then complete. Since the datasheet does
+ * not currently specify the exact sequence, we have chosen something
+ * that seems to work with our device.
+ */
+static void ks_soft_reset(struct ks_net *ks, unsigned op)
+{
+ /* Disable interrupt first */
+ ks_wrreg16(ks, KS_IER, 0x0000);
+ ks_wrreg16(ks, KS_GRR, op);
+ mdelay(10); /* wait a short time to effect reset */
+ ks_wrreg16(ks, KS_GRR, 0);
+ mdelay(1); /* wait for condition to clear */
+}
+
+
+/**
+ * ks_read_qmu - read 1 pkt data from the QMU.
+ * @ks: The chip information
+ * @buf: buffer address to save 1 pkt
+ * @len: Pkt length
+ * Here is the sequence to read 1 pkt:
+ * 1. set sudo DMA mode
+ * 2. read prepend data
+ * 3. read pkt data
+ * 4. reset sudo DMA Mode
+ */
+static inline void ks_read_qmu(struct ks_net *ks, u16 *buf, u32 len)
+{
+ u32 r = ks->extra_byte & 0x1 ;
+ u32 w = ks->extra_byte - r;
+
+ /* 1. set sudo DMA mode */
+ ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
+ ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+
+ /* 2. read prepend data */
+ /**
+ * read 4 + extra bytes and discard them.
+ * extra bytes for dummy, 2 for status, 2 for len
+ */
+
+ /* use likely(r) for 8 bit access for performance */
+ if (unlikely(r))
+ ioread8(ks->hw_addr);
+ ks_inblk(ks, buf, w + 2 + 2);
+
+ /* 3. read pkt data */
+ ks_inblk(ks, buf, ALIGN(len, 4));
+
+ /* 4. reset sudo DMA Mode */
+ ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
+}
+
+/**
+ * ks_rcv - read multiple pkts data from the QMU.
+ * @ks: The chip information
+ * @netdev: The network device being opened.
+ *
+ * Read all of header information before reading pkt content.
+ * It is not allowed only port of pkts in QMU after issuing
+ * interrupt ack.
+ */
+static void ks_rcv(struct ks_net *ks, struct net_device *netdev)
+{
+ u32 i;
+ struct type_frame_head *frame_hdr = ks->frame_head_info;
+ struct sk_buff *skb;
+
+ ks->frame_cnt = ks_rdreg16(ks, KS_RXFCTR) >> 8;
+
+ /* read all header information */
+ for (i = 0; i < ks->frame_cnt; i++) {
+ /* Checking Received packet status */
+ frame_hdr->sts = ks_rdreg16(ks, KS_RXFHSR);
+ /* Get packet len from hardware */
+ frame_hdr->len = ks_rdreg16(ks, KS_RXFHBCR);
+ frame_hdr++;
+ }
+
+ frame_hdr = ks->frame_head_info;
+ while (ks->frame_cnt--) {
+ skb = dev_alloc_skb(frame_hdr->len + 16);
+ if (likely(skb && (frame_hdr->sts & RXFSHR_RXFV) &&
+ (frame_hdr->len < RX_BUF_SIZE) && frame_hdr->len)) {
+ skb_reserve(skb, 2);
+ /* read data block including CRC 4 bytes */
+ ks_read_qmu(ks, (u16 *)skb->data, frame_hdr->len + 4);
+ skb_put(skb, frame_hdr->len);
+ skb->dev = netdev;
+ skb->protocol = eth_type_trans(skb, netdev);
+ netif_rx(skb);
+ } else {
+ printk(KERN_ERR "%s: err:skb alloc\n", __func__);
+ ks_wrreg16(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_RRXEF));
+ if (skb)
+ dev_kfree_skb_irq(skb);
+ }
+ frame_hdr++;
+ }
+}
+
+/**
+ * ks_update_link_status - link status update.
+ * @netdev: The network device being opened.
+ * @ks: The chip information
+ *
+ */
+
+static void ks_update_link_status(struct net_device *netdev, struct ks_net *ks)
+{
+ /* check the status of the link */
+ u32 link_up_status;
+ if (ks_rdreg16(ks, KS_P1SR) & P1SR_LINK_GOOD) {
+ netif_carrier_on(netdev);
+ link_up_status = true;
+ } else {
+ netif_carrier_off(netdev);
+ link_up_status = false;
+ }
+ if (netif_msg_link(ks))
+ ks_dbg(ks, "%s: %s\n",
+ __func__, link_up_status ? "UP" : "DOWN");
+}
+
+/**
+ * ks_irq - device interrupt handler
+ * @irq: Interrupt number passed from the IRQ hnalder.
+ * @pw: The private word passed to register_irq(), our struct ks_net.
+ *
+ * This is the handler invoked to find out what happened
+ *
+ * Read the interrupt status, work out what needs to be done and then clear
+ * any of the interrupts that are not needed.
+ */
+
+static irqreturn_t ks_irq(int irq, void *pw)
+{
+ struct ks_net *ks = pw;
+ struct net_device *netdev = ks->netdev;
+ u16 status;
+
+ /*this should be the first in IRQ handler */
+ ks_save_cmd_reg(ks);
+
+ status = ks_rdreg16(ks, KS_ISR);
+ if (unlikely(!status)) {
+ ks_restore_cmd_reg(ks);
+ return IRQ_NONE;
+ }
+
+ ks_wrreg16(ks, KS_ISR, status);
+
+ if (likely(status & IRQ_RXI))
+ ks_rcv(ks, netdev);
+
+ if (unlikely(status & IRQ_LCI))
+ ks_update_link_status(netdev, ks);
+
+ if (unlikely(status & IRQ_TXI))
+ netif_wake_queue(netdev);
+
+ if (unlikely(status & IRQ_LDI)) {
+
+ u16 pmecr = ks_rdreg16(ks, KS_PMECR);
+ pmecr &= ~PMECR_WKEVT_MASK;
+ ks_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK);
+ }
+
+ /* this should be the last in IRQ handler*/
+ ks_restore_cmd_reg(ks);
+ return IRQ_HANDLED;
+}
+
+
+/**
+ * ks_net_open - open network device
+ * @netdev: The network device being opened.
+ *
+ * Called when the network device is marked active, such as a user executing
+ * 'ifconfig up' on the device.
+ */
+static int ks_net_open(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ int err;
+
+#define KS_INT_FLAGS (IRQF_DISABLED|IRQF_TRIGGER_LOW)
+ /* lock the card, even if we may not actually do anything
+ * else at the moment.
+ */
+
+ if (netif_msg_ifup(ks))
+ ks_dbg(ks, "%s - entry\n", __func__);
+
+ /* reset the HW */
+ err = request_irq(ks->irq, ks_irq, KS_INT_FLAGS, DRV_NAME, ks);
+
+ if (err) {
+ printk(KERN_ERR "Failed to request IRQ: %d: %d\n",
+ ks->irq, err);
+ return err;
+ }
+
+ if (netif_msg_ifup(ks))
+ ks_dbg(ks, "network device %s up\n", netdev->name);
+
+ return 0;
+}
+
+/**
+ * ks_net_stop - close network device
+ * @netdev: The device being closed.
+ *
+ * Called to close down a network device which has been active. Cancell any
+ * work, shutdown the RX and TX process and then place the chip into a low
+ * power state whilst it is not being used.
+ */
+static int ks_net_stop(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+
+ if (netif_msg_ifdown(ks))
+ ks_info(ks, "%s: shutting down\n", netdev->name);
+
+ netif_stop_queue(netdev);
+
+ kfree(ks->frame_head_info);
+
+ mutex_lock(&ks->lock);
+
+ /* turn off the IRQs and ack any outstanding */
+ ks_wrreg16(ks, KS_IER, 0x0000);
+ ks_wrreg16(ks, KS_ISR, 0xffff);
+
+ /* shutdown RX process */
+ ks_wrreg16(ks, KS_RXCR1, 0x0000);
+
+ /* shutdown TX process */
+ ks_wrreg16(ks, KS_TXCR, 0x0000);
+
+ /* set powermode to soft power down to save power */
+ ks_set_powermode(ks, PMECR_PM_SOFTDOWN);
+ free_irq(ks->irq, netdev);
+ mutex_unlock(&ks->lock);
+ return 0;
+}
+
+
+/**
+ * ks_write_qmu - write 1 pkt data to the QMU.
+ * @ks: The chip information
+ * @pdata: buffer address to save 1 pkt
+ * @len: Pkt length in byte
+ * Here is the sequence to write 1 pkt:
+ * 1. set sudo DMA mode
+ * 2. write status/length
+ * 3. write pkt data
+ * 4. reset sudo DMA Mode
+ * 5. reset sudo DMA mode
+ * 6. Wait until pkt is out
+ */
+static void ks_write_qmu(struct ks_net *ks, u8 *pdata, u16 len)
+{
+ unsigned fid = ks->fid;
+
+ fid = ks->fid;
+ ks->fid = (ks->fid + 1) & TXFR_TXFID_MASK;
+
+ /* reduce the tx interrupt occurrances. */
+ if (!fid)
+ fid |= TXFR_TXIC; /* irq on completion */
+
+ /* start header at txb[0] to align txw entries */
+ ks->txh.txw[0] = cpu_to_le16(fid);
+ ks->txh.txw[1] = cpu_to_le16(len);
+
+ /* 1. set sudo-DMA mode */
+ ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+ /* 2. write status/lenth info */
+ ks_outblk(ks, ks->txh.txw, 4);
+ /* 3. write pkt data */
+ ks_outblk(ks, (u16 *)pdata, ALIGN(len, 4));
+ /* 4. reset sudo-DMA mode */
+ ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
+ /* 5. Enqueue Tx(move the pkt from TX buffer into TXQ) */
+ ks_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
+ /* 6. wait until TXQCR_METFE is auto-cleared */
+ while (ks_rdreg16(ks, KS_TXQCR) & TXQCR_METFE)
+ ;
+}
+
+static void ks_disable_int(struct ks_net *ks)
+{
+ ks_wrreg16(ks, KS_IER, 0x0000);
+} /* ks_disable_int */
+
+static void ks_enable_int(struct ks_net *ks)
+{
+ ks_wrreg16(ks, KS_IER, ks->rc_ier);
+} /* ks_enable_int */
+
+/**
+ * ks_start_xmit - transmit packet
+ * @skb : The buffer to transmit
+ * @netdev : The device used to transmit the packet.
+ *
+ * Called by the network layer to transmit the @skb.
+ * spin_lock_irqsave is required because tx and rx should be mutual exclusive.
+ * So while tx is in-progress, prevent IRQ interrupt from happenning.
+ */
+static int ks_start_xmit(struct sk_buff *skb, struct net_device *netdev)
+{
+ int retv = NETDEV_TX_OK;
+ struct ks_net *ks = netdev_priv(netdev);
+
+ disable_irq(netdev->irq);
+ ks_disable_int(ks);
+ spin_lock(&ks->statelock);
+
+ /* Extra space are required:
+ * 4 byte for alignment, 4 for status/length, 4 for CRC
+ */
+
+ if (likely(ks_tx_fifo_space(ks) >= skb->len + 12)) {
+ ks_write_qmu(ks, skb->data, skb->len);
+ dev_kfree_skb(skb);
+ } else
+ retv = NETDEV_TX_BUSY;
+ spin_unlock(&ks->statelock);
+ ks_enable_int(ks);
+ enable_irq(netdev->irq);
+ return retv;
+}
+
+/**
+ * ks_start_rx - ready to serve pkts
+ * @ks : The chip information
+ *
+ */
+static void ks_start_rx(struct ks_net *ks)
+{
+ u16 cntl;
+
+ /* Enables QMU Receive (RXCR1). */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+ cntl |= RXCR1_RXE ;
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+} /* ks_start_rx */
+
+/**
+ * ks_stop_rx - stop to serve pkts
+ * @ks : The chip information
+ *
+ */
+static void ks_stop_rx(struct ks_net *ks)
+{
+ u16 cntl;
+
+ /* Disables QMU Receive (RXCR1). */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+ cntl &= ~RXCR1_RXE ;
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+
+} /* ks_stop_rx */
+
+static unsigned long const ethernet_polynomial = 0x04c11db7U;
+
+static unsigned long ether_gen_crc(int length, u8 *data)
+{
+ long crc = -1;
+ while (--length >= 0) {
+ u8 current_octet = *data++;
+ int bit;
+
+ for (bit = 0; bit < 8; bit++, current_octet >>= 1) {
+ crc = (crc << 1) ^
+ ((crc < 0) ^ (current_octet & 1) ?
+ ethernet_polynomial : 0);
+ }
+ }
+ return (unsigned long)crc;
+} /* ether_gen_crc */
+
+/**
+* ks_set_grpaddr - set multicast information
+* @ks : The chip information
+*/
+
+static void ks_set_grpaddr(struct ks_net *ks)
+{
+ u8 i;
+ u32 index, position, value;
+
+ memset(ks->mcast_bits, 0, sizeof(u8) * HW_MCAST_SIZE);
+
+ for (i = 0; i < ks->mcast_lst_size; i++) {
+ position = (ether_gen_crc(6, ks->mcast_lst[i]) >> 26) & 0x3f;
+ index = position >> 3;
+ value = 1 << (position & 7);
+ ks->mcast_bits[index] |= (u8)value;
+ }
+
+ for (i = 0; i < HW_MCAST_SIZE; i++) {
+ if (i & 1) {
+ ks_wrreg16(ks, (u16)((KS_MAHTR0 + i) & ~1),
+ (ks->mcast_bits[i] << 8) |
+ ks->mcast_bits[i - 1]);
+ }
+ }
+} /* ks_set_grpaddr */
+
+/*
+* ks_clear_mcast - clear multicast information
+*
+* @ks : The chip information
+* This routine removes all mcast addresses set in the hardware.
+*/
+
+static void ks_clear_mcast(struct ks_net *ks)
+{
+ u16 i, mcast_size;
+ for (i = 0; i < HW_MCAST_SIZE; i++)
+ ks->mcast_bits[i] = 0;
+
+ mcast_size = HW_MCAST_SIZE >> 2;
+ for (i = 0; i < mcast_size; i++)
+ ks_wrreg16(ks, KS_MAHTR0 + (2*i), 0);
+}
+
+static void ks_set_promis(struct ks_net *ks, u16 promiscuous_mode)
+{
+ u16 cntl;
+ ks->promiscuous = promiscuous_mode;
+ ks_stop_rx(ks); /* Stop receiving for reconfiguration */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+
+ cntl &= ~RXCR1_FILTER_MASK;
+ if (promiscuous_mode)
+ /* Enable Promiscuous mode */
+ cntl |= RXCR1_RXAE | RXCR1_RXINVF;
+ else
+ /* Disable Promiscuous mode (default normal mode) */
+ cntl |= RXCR1_RXPAFMA;
+
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+
+ if (ks->enabled)
+ ks_start_rx(ks);
+
+} /* ks_set_promis */
+
+static void ks_set_mcast(struct ks_net *ks, u16 mcast)
+{
+ u16 cntl;
+
+ ks->all_mcast = mcast;
+ ks_stop_rx(ks); /* Stop receiving for reconfiguration */
+ cntl = ks_rdreg16(ks, KS_RXCR1);
+ cntl &= ~RXCR1_FILTER_MASK;
+ if (mcast)
+ /* Enable "Perfect with Multicast address passed mode" */
+ cntl |= (RXCR1_RXAE | RXCR1_RXMAFMA | RXCR1_RXPAFMA);
+ else
+ /**
+ * Disable "Perfect with Multicast address passed
+ * mode" (normal mode).
+ */
+ cntl |= RXCR1_RXPAFMA;
+
+ ks_wrreg16(ks, KS_RXCR1, cntl);
+
+ if (ks->enabled)
+ ks_start_rx(ks);
+} /* ks_set_mcast */
+
+static void ks_set_rx_mode(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ struct dev_mc_list *ptr;
+
+ /* Turn on/off promiscuous mode. */
+ if ((netdev->flags & IFF_PROMISC) == IFF_PROMISC)
+ ks_set_promis(ks,
+ (u16)((netdev->flags & IFF_PROMISC) == IFF_PROMISC));
+ /* Turn on/off all mcast mode. */
+ else if ((netdev->flags & IFF_ALLMULTI) == IFF_ALLMULTI)
+ ks_set_mcast(ks,
+ (u16)((netdev->flags & IFF_ALLMULTI) == IFF_ALLMULTI));
+ else
+ ks_set_promis(ks, false);
+
+ if ((netdev->flags & IFF_MULTICAST) && netdev->mc_count) {
+ if (netdev->mc_count <= MAX_MCAST_LST) {
+ int i = 0;
+ for (ptr = netdev->mc_list; ptr; ptr = ptr->next) {
+ if (!(*ptr->dmi_addr & 1))
+ continue;
+ if (i >= MAX_MCAST_LST)
+ break;
+ memcpy(ks->mcast_lst[i++], ptr->dmi_addr,
+ MAC_ADDR_LEN);
+ }
+ ks->mcast_lst_size = (u8)i;
+ ks_set_grpaddr(ks);
+ } else {
+ /**
+ * List too big to support so
+ * turn on all mcast mode.
+ */
+ ks->mcast_lst_size = MAX_MCAST_LST;
+ ks_set_mcast(ks, true);
+ }
+ } else {
+ ks->mcast_lst_size = 0;
+ ks_clear_mcast(ks);
+ }
+} /* ks_set_rx_mode */
+
+static void ks_set_mac(struct ks_net *ks, u8 *data)
+{
+ u16 *pw = (u16 *)data;
+ u16 w, u;
+
+ ks_stop_rx(ks); /* Stop receiving for reconfiguration */
+
+ u = *pw++;
+ w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
+ ks_wrreg16(ks, KS_MARH, w);
+
+ u = *pw++;
+ w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
+ ks_wrreg16(ks, KS_MARM, w);
+
+ u = *pw;
+ w = ((u & 0xFF) << 8) | ((u >> 8) & 0xFF);
+ ks_wrreg16(ks, KS_MARL, w);
+
+ memcpy(ks->mac_addr, data, 6);
+
+ if (ks->enabled)
+ ks_start_rx(ks);
+}
+
+static int ks_set_mac_address(struct net_device *netdev, void *paddr)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ struct sockaddr *addr = paddr;
+ u8 *da;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+
+ da = (u8 *)netdev->dev_addr;
+
+ ks_set_mac(ks, da);
+ return 0;
+}
+
+static int ks_net_ioctl(struct net_device *netdev, struct ifreq *req, int cmd)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+
+ if (!netif_running(netdev))
+ return -EINVAL;
+
+ return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL);
+}
+
+static const struct net_device_ops ks_netdev_ops = {
+ .ndo_open = ks_net_open,
+ .ndo_stop = ks_net_stop,
+ .ndo_do_ioctl = ks_net_ioctl,
+ .ndo_start_xmit = ks_start_xmit,
+ .ndo_set_mac_address = ks_set_mac_address,
+ .ndo_set_rx_mode = ks_set_rx_mode,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
+/* ethtool support */
+
+static void ks_get_drvinfo(struct net_device *netdev,
+ struct ethtool_drvinfo *di)
+{
+ strlcpy(di->driver, DRV_NAME, sizeof(di->driver));
+ strlcpy(di->version, "1.00", sizeof(di->version));
+ strlcpy(di->bus_info, dev_name(netdev->dev.parent),
+ sizeof(di->bus_info));
+}
+
+static u32 ks_get_msglevel(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return ks->msg_enable;
+}
+
+static void ks_set_msglevel(struct net_device *netdev, u32 to)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ ks->msg_enable = to;
+}
+
+static int ks_get_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_ethtool_gset(&ks->mii, cmd);
+}
+
+static int ks_set_settings(struct net_device *netdev, struct ethtool_cmd *cmd)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_ethtool_sset(&ks->mii, cmd);
+}
+
+static u32 ks_get_link(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_link_ok(&ks->mii);
+}
+
+static int ks_nway_reset(struct net_device *netdev)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ return mii_nway_restart(&ks->mii);
+}
+
+static const struct ethtool_ops ks_ethtool_ops = {
+ .get_drvinfo = ks_get_drvinfo,
+ .get_msglevel = ks_get_msglevel,
+ .set_msglevel = ks_set_msglevel,
+ .get_settings = ks_get_settings,
+ .set_settings = ks_set_settings,
+ .get_link = ks_get_link,
+ .nway_reset = ks_nway_reset,
+};
+
+/* MII interface controls */
+
+/**
+ * ks_phy_reg - convert MII register into a KS8851 register
+ * @reg: MII register number.
+ *
+ * Return the KS8851 register number for the corresponding MII PHY register
+ * if possible. Return zero if the MII register has no direct mapping to the
+ * KS8851 register set.
+ */
+static int ks_phy_reg(int reg)
+{
+ switch (reg) {
+ case MII_BMCR:
+ return KS_P1MBCR;
+ case MII_BMSR:
+ return KS_P1MBSR;
+ case MII_PHYSID1:
+ return KS_PHY1ILR;
+ case MII_PHYSID2:
+ return KS_PHY1IHR;
+ case MII_ADVERTISE:
+ return KS_P1ANAR;
+ case MII_LPA:
+ return KS_P1ANLPR;
+ }
+
+ return 0x0;
+}
+
+/**
+ * ks_phy_read - MII interface PHY register read.
+ * @netdev: The network device the PHY is on.
+ * @phy_addr: Address of PHY (ignored as we only have one)
+ * @reg: The register to read.
+ *
+ * This call reads data from the PHY register specified in @reg. Since the
+ * device does not support all the MII registers, the non-existant values
+ * are always returned as zero.
+ *
+ * We return zero for unsupported registers as the MII code does not check
+ * the value returned for any error status, and simply returns it to the
+ * caller. The mii-tool that the driver was tested with takes any -ve error
+ * as real PHY capabilities, thus displaying incorrect data to the user.
+ */
+static int ks_phy_read(struct net_device *netdev, int phy_addr, int reg)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ int ksreg;
+ int result;
+
+ ksreg = ks_phy_reg(reg);
+ if (!ksreg)
+ return 0x0; /* no error return allowed, so use zero */
+
+ mutex_lock(&ks->lock);
+ result = ks_rdreg16(ks, ksreg);
+ mutex_unlock(&ks->lock);
+
+ return result;
+}
+
+static void ks_phy_write(struct net_device *netdev,
+ int phy, int reg, int value)
+{
+ struct ks_net *ks = netdev_priv(netdev);
+ int ksreg;
+
+ ksreg = ks_phy_reg(reg);
+ if (ksreg) {
+ mutex_lock(&ks->lock);
+ ks_wrreg16(ks, ksreg, value);
+ mutex_unlock(&ks->lock);
+ }
+}
+
+/**
+ * ks_read_selftest - read the selftest memory info.
+ * @ks: The device state
+ *
+ * Read and check the TX/RX memory selftest information.
+ */
+static int ks_read_selftest(struct ks_net *ks)
+{
+ unsigned both_done = MBIR_TXMBF | MBIR_RXMBF;
+ int ret = 0;
+ unsigned rd;
+
+ rd = ks_rdreg16(ks, KS_MBIR);
+
+ if ((rd & both_done) != both_done) {
+ ks_warn(ks, "Memory selftest not finished\n");
+ return 0;
+ }
+
+ if (rd & MBIR_TXMBFA) {
+ ks_err(ks, "TX memory selftest fails\n");
+ ret |= 1;
+ }
+
+ if (rd & MBIR_RXMBFA) {
+ ks_err(ks, "RX memory selftest fails\n");
+ ret |= 2;
+ }
+
+ ks_info(ks, "the selftest passes\n");
+ return ret;
+}
+
+static void ks_disable(struct ks_net *ks)
+{
+ u16 w;
+
+ w = ks_rdreg16(ks, KS_TXCR);
+
+ /* Disables QMU Transmit (TXCR). */
+ w &= ~TXCR_TXE;
+ ks_wrreg16(ks, KS_TXCR, w);
+
+ /* Disables QMU Receive (RXCR1). */
+ w = ks_rdreg16(ks, KS_RXCR1);
+ w &= ~RXCR1_RXE ;
+ ks_wrreg16(ks, KS_RXCR1, w);
+
+ ks->enabled = false;
+
+} /* ks_disable */
+
+static void ks_setup(struct ks_net *ks)
+{
+ u16 w;
+
+ /**
+ * Configure QMU Transmit
+ */
+
+ /* Setup Transmit Frame Data Pointer Auto-Increment (TXFDPR) */
+ ks_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI);
+
+ /* Setup Receive Frame Data Pointer Auto-Increment */
+ ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
+
+ /* Setup Receive Frame Threshold - 1 frame (RXFCTFC) */
+ ks_wrreg16(ks, KS_RXFCTR, 1 & RXFCTR_THRESHOLD_MASK);
+
+ /* Setup RxQ Command Control (RXQCR) */
+ ks->rc_rxqcr = RXQCR_CMD_CNTL;
+ ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
+
+ /**
+ * set the force mode to half duplex, default is full duplex
+ * because if the auto-negotiation fails, most switch uses
+ * half-duplex.
+ */
+
+ w = ks_rdreg16(ks, KS_P1MBCR);
+ w &= ~P1MBCR_FORCE_FDX;
+ ks_wrreg16(ks, KS_P1MBCR, w);
+
+ w = TXCR_TXFCE | TXCR_TXPE | TXCR_TXCRC | TXCR_TCGIP;
+ ks_wrreg16(ks, KS_TXCR, w);
+
+ w = RXCR1_RXFCE | RXCR1_RXBE | RXCR1_RXUE;
+
+ if (ks->promiscuous) /* bPromiscuous */
+ w |= (RXCR1_RXAE | RXCR1_RXINVF);
+ else if (ks->all_mcast) /* Multicast address passed mode */
+ w |= (RXCR1_RXAE | RXCR1_RXMAFMA | RXCR1_RXPAFMA);
+ else /* Normal mode */
+ w |= RXCR1_RXPAFMA;
+
+ ks_wrreg16(ks, KS_RXCR1, w);
+} /*ks_setup */
+
+
+static void ks_setup_int(struct ks_net *ks)
+{
+ ks->rc_ier = 0x00;
+ /* Clear the interrupts status of the hardware. */
+ ks_wrreg16(ks, KS_ISR, 0xffff);
+
+ /* Enables the interrupts of the hardware. */
+ ks->rc_ier = (IRQ_LCI | IRQ_TXI | IRQ_RXI);
+} /* ks_setup_int */
+
+void ks_enable(struct ks_net *ks)
+{
+ u16 w;
+
+ w = ks_rdreg16(ks, KS_TXCR);
+ /* Enables QMU Transmit (TXCR). */
+ ks_wrreg16(ks, KS_TXCR, w | TXCR_TXE);
+
+ /*
+ * RX Frame Count Threshold Enable and Auto-Dequeue RXQ Frame
+ * Enable
+ */
+
+ w = ks_rdreg16(ks, KS_RXQCR);
+ ks_wrreg16(ks, KS_RXQCR, w | RXQCR_RXFCTE);
+
+ /* Enables QMU Receive (RXCR1). */
+ w = ks_rdreg16(ks, KS_RXCR1);
+ ks_wrreg16(ks, KS_RXCR1, w | RXCR1_RXE);
+ ks->enabled = true;
+} /* ks_enable */
+
+static int ks_hw_init(struct ks_net *ks)
+{
+#define MHEADER_SIZE (sizeof(struct type_frame_head) * MAX_RECV_FRAMES)
+ ks->promiscuous = 0;
+ ks->all_mcast = 0;
+ ks->mcast_lst_size = 0;
+
+ ks->frame_head_info = (struct type_frame_head *) \
+ kmalloc(MHEADER_SIZE, GFP_KERNEL);
+ if (!ks->frame_head_info) {
+ printk(KERN_ERR "Error: Fail to allocate frame memory\n");
+ return false;
+ }
+
+ ks_set_mac(ks, KS_DEFAULT_MAC_ADDRESS);
+ return true;
+}
+
+
+static int __devinit ks8851_probe(struct platform_device *pdev)
+{
+ int err = -ENOMEM;
+ struct resource *io_d, *io_c;
+ struct net_device *netdev;
+ struct ks_net *ks;
+ u16 id, data;
+
+ io_d = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ io_c = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+ if (!request_mem_region(io_d->start, resource_size(io_d), DRV_NAME))
+ goto err_mem_region;
+
+ if (!request_mem_region(io_c->start, resource_size(io_c), DRV_NAME))
+ goto err_mem_region1;
+
+ netdev = alloc_etherdev(sizeof(struct ks_net));
+ if (!netdev)
+ goto err_alloc_etherdev;
+
+ SET_NETDEV_DEV(netdev, &pdev->dev);
+
+ ks = netdev_priv(netdev);
+ ks->netdev = netdev;
+ ks->hw_addr = ioremap(io_d->start, resource_size(io_d));
+
+ if (!ks->hw_addr)
+ goto err_ioremap;
+
+ ks->hw_addr_cmd = ioremap(io_c->start, resource_size(io_c));
+ if (!ks->hw_addr_cmd)
+ goto err_ioremap1;
+
+ ks->irq = platform_get_irq(pdev, 0);
+
+ if (ks->irq < 0) {
+ err = ks->irq;
+ goto err_get_irq;
+ }
+
+ ks->pdev = pdev;
+
+ mutex_init(&ks->lock);
+ spin_lock_init(&ks->statelock);
+
+ netdev->netdev_ops = &ks_netdev_ops;
+ netdev->ethtool_ops = &ks_ethtool_ops;
+
+ /* setup mii state */
+ ks->mii.dev = netdev;
+ ks->mii.phy_id = 1,
+ ks->mii.phy_id_mask = 1;
+ ks->mii.reg_num_mask = 0xf;
+ ks->mii.mdio_read = ks_phy_read;
+ ks->mii.mdio_write = ks_phy_write;
+
+ ks_info(ks, "message enable is %d\n", msg_enable);
+ /* set the default message enable */
+ ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV |
+ NETIF_MSG_PROBE |
+ NETIF_MSG_LINK));
+ ks_read_config(ks);
+
+ /* simple check for a valid chip being connected to the bus */
+ if ((ks_rdreg16(ks, KS_CIDER) & ~CIDER_REV_MASK) != CIDER_ID) {
+ ks_err(ks, "failed to read device ID\n");
+ err = -ENODEV;
+ goto err_register;
+ }
+
+ if (ks_read_selftest(ks)) {
+ ks_err(ks, "failed to read device ID\n");
+ err = -ENODEV;
+ goto err_register;
+ }
+
+ err = register_netdev(netdev);
+ if (err)
+ goto err_register;
+
+ platform_set_drvdata(pdev, netdev);
+
+ ks_soft_reset(ks, GRR_GSR);
+ ks_hw_init(ks);
+ ks_disable(ks);
+ ks_setup(ks);
+ ks_setup_int(ks);
+ ks_enable_int(ks);
+ ks_enable(ks);
+ memcpy(netdev->dev_addr, ks->mac_addr, 6);
+
+ data = ks_rdreg16(ks, KS_OBCR);
+ ks_wrreg16(ks, KS_OBCR, data | OBCR_ODS_16MA);
+
+ /**
+ * If you want to use the default MAC addr,
+ * comment out the 2 functions below.
+ */
+
+ random_ether_addr(netdev->dev_addr);
+ ks_set_mac(ks, netdev->dev_addr);
+
+ id = ks_rdreg16(ks, KS_CIDER);
+
+ printk(KERN_INFO DRV_NAME
+ " Found chip, family: 0x%x, id: 0x%x, rev: 0x%x\n",
+ (id >> 8) & 0xff, (id >> 4) & 0xf, (id >> 1) & 0x7);
+ return 0;
+
+err_register:
+err_get_irq:
+ iounmap(ks->hw_addr_cmd);
+err_ioremap1:
+ iounmap(ks->hw_addr);
+err_ioremap:
+ free_netdev(netdev);
+err_alloc_etherdev:
+ release_mem_region(io_c->start, resource_size(io_c));
+err_mem_region1:
+ release_mem_region(io_d->start, resource_size(io_d));
+err_mem_region:
+ return err;
+}
+
+static int __devexit ks8851_remove(struct platform_device *pdev)
+{
+ struct net_device *netdev = platform_get_drvdata(pdev);
+ struct ks_net *ks = netdev_priv(netdev);
+ struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ unregister_netdev(netdev);
+ iounmap(ks->hw_addr);
+ free_netdev(netdev);
+ release_mem_region(iomem->start, resource_size(iomem));
+ platform_set_drvdata(pdev, NULL);
+ return 0;
+
+}
+
+static struct platform_driver ks8851_platform_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = ks8851_probe,
+ .remove = __devexit_p(ks8851_remove),
+};
+
+static int __init ks8851_init(void)
+{
+ return platform_driver_register(&ks8851_platform_driver);
+}
+
+static void __exit ks8851_exit(void)
+{
+ platform_driver_unregister(&ks8851_platform_driver);
+}
+
+module_init(ks8851_init);
+module_exit(ks8851_exit);
+
+MODULE_DESCRIPTION("KS8851 MLL Network driver");
+MODULE_AUTHOR("David Choi <david.choi@micrel.com>");
+MODULE_LICENSE("GPL");
+module_param_named(message, msg_enable, int, 0);
+MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)");
+
static struct platform_driver meth_driver = {
.probe = meth_probe,
- .remove = __devexit_p(meth_remove),
+ .remove = __exit_p(meth_remove),
.driver = {
.name = "meth",
.owner = THIS_MODULE,
*/
#include <linux/mlx4/cmd.h>
+#include <linux/cache.h>
#include "fw.h"
#include "icm.h"
#define INIT_HCA_IN_SIZE 0x200
#define INIT_HCA_VERSION_OFFSET 0x000
#define INIT_HCA_VERSION 2
+#define INIT_HCA_CACHELINE_SZ_OFFSET 0x0e
#define INIT_HCA_FLAGS_OFFSET 0x014
#define INIT_HCA_QPC_OFFSET 0x020
#define INIT_HCA_QPC_BASE_OFFSET (INIT_HCA_QPC_OFFSET + 0x10)
*((u8 *) mailbox->buf + INIT_HCA_VERSION_OFFSET) = INIT_HCA_VERSION;
+ *((u8 *) mailbox->buf + INIT_HCA_CACHELINE_SZ_OFFSET) =
+ (ilog2(cache_line_size()) - 4) << 5;
+
#if defined(__LITTLE_ENDIAN)
*(inbox + INIT_HCA_FLAGS_OFFSET / 4) &= ~cpu_to_be32(1 << 1);
#elif defined(__BIG_ENDIAN)
}
netxen_schedule_work(adapter, netxen_fw_poll_work, FW_POLL_DELAY);
+ return 0;
err_out_detach:
netxen_nic_detach(adapter);
netif_wake_queue(adapter->netdev);
- goto done;
+ clear_bit(__NX_RESETTING, &adapter->state);
} else {
+ clear_bit(__NX_RESETTING, &adapter->state);
if (!netxen_nic_reset_context(adapter)) {
adapter->netdev->trans_start = jiffies;
- goto done;
+ return;
}
/* context reset failed, fall through for fw reset */
request_reset:
adapter->need_fw_reset = 1;
-done:
- clear_bit(__NX_RESETTING, &adapter->state);
}
struct net_device_stats *netxen_nic_get_stats(struct net_device *netdev)
base = &virt[hw_info[i].offset & (req.Size-1)];
if ((readb(base+0) == hw_info[i].a0) &&
(readb(base+2) == hw_info[i].a1) &&
- (readb(base+4) == hw_info[i].a2))
- break;
- }
- if (i < NR_INFO) {
- for (j = 0; j < 6; j++)
- dev->dev_addr[j] = readb(base + (j<<1));
+ (readb(base+4) == hw_info[i].a2)) {
+ for (j = 0; j < 6; j++)
+ dev->dev_addr[j] = readb(base + (j<<1));
+ break;
+ }
}
iounmap(virt);
* session or the special tunnel type.
*/
static int pppol2tp_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct pppol2tp_session *session = sk->sk_user_data;
/* adapter flags definitions. */
enum {
- QL_ADAPTER_UP = (1 << 0), /* Adapter has been brought up. */
- QL_LEGACY_ENABLED = (1 << 3),
- QL_MSI_ENABLED = (1 << 3),
- QL_MSIX_ENABLED = (1 << 4),
- QL_DMA64 = (1 << 5),
- QL_PROMISCUOUS = (1 << 6),
- QL_ALLMULTI = (1 << 7),
- QL_PORT_CFG = (1 << 8),
- QL_CAM_RT_SET = (1 << 9),
+ QL_ADAPTER_UP = 0, /* Adapter has been brought up. */
+ QL_LEGACY_ENABLED = 1,
+ QL_MSI_ENABLED = 2,
+ QL_MSIX_ENABLED = 3,
+ QL_DMA64 = 4,
+ QL_PROMISCUOUS = 5,
+ QL_ALLMULTI = 6,
+ QL_PORT_CFG = 7,
+ QL_CAM_RT_SET = 8,
};
/* link_status bit definitions */
{
int status = 0;
- status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
+ /* Clear all the entries in the routing table. */
+ status = ql_clear_routing_entries(qdev);
if (status)
return status;
- /* Clear all the entries in the routing table. */
- status = ql_clear_routing_entries(qdev);
+ status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
if (status)
- goto exit;
+ return status;
status = ql_set_routing_reg(qdev, RT_IDX_ALL_ERR_SLOT, RT_IDX_ERR, 1);
if (status) {
ql_free_rx_buffers(qdev);
- spin_lock(&qdev->hw_lock);
status = ql_adapter_reset(qdev);
if (status)
QPRINTK(qdev, IFDOWN, ERR, "reset(func #%d) FAILED!\n",
qdev->func);
- spin_unlock(&qdev->hw_lock);
return status;
}
struct ql_adapter *qdev =
container_of(work, struct ql_adapter, asic_reset_work.work);
int status;
-
+ rtnl_lock();
status = ql_adapter_down(qdev);
if (status)
goto error;
status = ql_adapter_up(qdev);
if (status)
goto error;
-
+ rtnl_unlock();
return;
error:
QPRINTK(qdev, IFUP, ALERT,
"Driver up/down cycle failed, closing device\n");
- rtnl_lock();
+
set_bit(QL_ADAPTER_UP, &qdev->flags);
dev_close(qdev->ndev);
rtnl_unlock();
return err;
}
+ qdev->ndev = ndev;
+ qdev->pdev = pdev;
+ pci_set_drvdata(pdev, ndev);
pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
if (pos <= 0) {
dev_err(&pdev->dev, PFX "Cannot find PCI Express capability, "
"aborting.\n");
- goto err_out;
+ return pos;
} else {
pci_read_config_word(pdev, pos + PCI_EXP_DEVCTL, &val16);
val16 &= ~PCI_EXP_DEVCTL_NOSNOOP_EN;
err = pci_request_regions(pdev, DRV_NAME);
if (err) {
dev_err(&pdev->dev, "PCI region request failed.\n");
- goto err_out;
+ return err;
}
pci_set_master(pdev);
goto err_out;
}
- pci_set_drvdata(pdev, ndev);
qdev->reg_base =
ioremap_nocache(pci_resource_start(pdev, 1),
pci_resource_len(pdev, 1));
goto err_out;
}
- qdev->ndev = ndev;
- qdev->pdev = pdev;
err = ql_get_board_info(qdev);
if (err) {
dev_err(&pdev->dev, "Register access failed.\n");
static struct platform_driver sgiseeq_driver = {
.probe = sgiseeq_probe,
- .remove = __devexit_p(sgiseeq_remove),
+ .remove = __exit_p(sgiseeq_remove),
.driver = {
.name = "sgiseeq",
.owner = THIS_MODULE,
#endif
err = -ENOMEM;
- hw = kzalloc(sizeof(*hw), GFP_KERNEL);
+ /* space for skge@pci:0000:04:00.0 */
+ hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:" )
+ + strlen(pci_name(pdev)) + 1, GFP_KERNEL);
if (!hw) {
dev_err(&pdev->dev, "cannot allocate hardware struct\n");
goto err_out_free_regions;
}
+ sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev));
hw->pdev = pdev;
spin_lock_init(&hw->hw_lock);
goto err_out_free_netdev;
}
- err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, dev->name, hw);
+ err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, hw->irq_name, hw);
if (err) {
dev_err(&pdev->dev, "%s: cannot assign irq %d\n",
dev->name, pdev->irq);
}
skge_show_addr(dev);
- if (hw->ports > 1 && (dev1 = skge_devinit(hw, 1, using_dac))) {
- if (register_netdev(dev1) == 0)
+ if (hw->ports > 1) {
+ dev1 = skge_devinit(hw, 1, using_dac);
+ if (dev1 && register_netdev(dev1) == 0)
skge_show_addr(dev1);
else {
/* Failure to register second port need not be fatal */
dev_warn(&pdev->dev, "register of second port failed\n");
hw->dev[1] = NULL;
- free_netdev(dev1);
+ hw->ports = 1;
+ if (dev1)
+ free_netdev(dev1);
}
}
pci_set_drvdata(pdev, hw);
u16 phy_addr;
spinlock_t phy_lock;
struct tasklet_struct phy_task;
+
+ char irq_name[0]; /* skge@pci:000:04:00.0 */
};
enum pause_control {
if (ramsize > 0) {
u32 rxspace;
- hw->flags |= SKY2_HW_RAM_BUFFER;
pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize);
if (ramsize < 16)
rxspace = ramsize / 2;
++hw->ports;
}
+ if (sky2_read8(hw, B2_E_0))
+ hw->flags |= SKY2_HW_RAM_BUFFER;
+
return 0;
}
wol_default = device_may_wakeup(&pdev->dev) ? WAKE_MAGIC : 0;
err = -ENOMEM;
- hw = kzalloc(sizeof(*hw), GFP_KERNEL);
+
+ hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:")
+ + strlen(pci_name(pdev)) + 1, GFP_KERNEL);
if (!hw) {
dev_err(&pdev->dev, "cannot allocate hardware struct\n");
goto err_out_free_regions;
}
hw->pdev = pdev;
+ sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev));
hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000);
if (!hw->regs) {
err = request_irq(pdev->irq, sky2_intr,
(hw->flags & SKY2_HW_USE_MSI) ? 0 : IRQF_SHARED,
- dev->name, hw);
+ hw->irq_name, hw);
if (err) {
dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq);
goto err_out_unregister;
struct timer_list watchdog_timer;
struct work_struct restart_work;
wait_queue_head_t msi_wait;
+
+ char irq_name[0];
};
static inline int sky2_is_copper(const struct sky2_hw *hw)
.ndo_open = vnet_open,
.ndo_stop = vnet_close,
.ndo_set_multicast_list = vnet_set_rx_mode,
- .ndo_change_mtu = eth_change_mtu,
.ndo_set_mac_address = vnet_set_mac_addr,
.ndo_validate_addr = eth_validate_addr,
.ndo_tx_timeout = vnet_tx_timeout,
struct tx_ring_info {
struct sk_buff *skb;
- u32 prev_vlan_tag;
};
struct tg3_config_info {
char *name;
unsigned long flags = 0;
- err = -EINVAL;
-
if (!capable(CAP_NET_ADMIN))
return -EPERM;
err = security_tun_dev_create();
flags |= TUN_TAP_DEV;
name = "tap%d";
} else
- goto failed;
+ return -EINVAL;
if (*ifr->ifr_name)
name = ifr->ifr_name;
int timeout)
{
struct usb_ctrlrequest *dr;
+ int retval;
dbg("kaweth_control()");
return -ENOMEM;
}
- dr->bRequestType= requesttype;
+ dr->bRequestType = requesttype;
dr->bRequest = request;
dr->wValue = cpu_to_le16(value);
dr->wIndex = cpu_to_le16(index);
dr->wLength = cpu_to_le16(size);
- return kaweth_internal_control_msg(kaweth->dev,
- pipe,
- dr,
- data,
- size,
- timeout);
+ retval = kaweth_internal_control_msg(kaweth->dev,
+ pipe,
+ dr,
+ data,
+ size,
+ timeout);
+
+ kfree(dr);
+ return retval;
}
/****************************************************************
.rx_fixup = smsc95xx_rx_fixup,
.tx_fixup = smsc95xx_tx_fixup,
.status = smsc95xx_status,
- .flags = FLAG_ETHER,
+ .flags = FLAG_ETHER | FLAG_SEND_ZLP,
};
static const struct usb_device_id products[] = {
USB_DEVICE(0x0424, 0x9500),
.driver_info = (unsigned long) &smsc95xx_info,
},
+ {
+ /* SMSC9505 USB Ethernet Device */
+ USB_DEVICE(0x0424, 0x9505),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9500A USB Ethernet Device */
+ USB_DEVICE(0x0424, 0x9E00),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9505A USB Ethernet Device */
+ USB_DEVICE(0x0424, 0x9E01),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
{
/* SMSC9512/9514 USB Hub & Ethernet Device */
USB_DEVICE(0x0424, 0xec00),
.driver_info = (unsigned long) &smsc95xx_info,
},
+ {
+ /* SMSC9500 USB Ethernet Device (SAL10) */
+ USB_DEVICE(0x0424, 0x9900),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9505 USB Ethernet Device (SAL10) */
+ USB_DEVICE(0x0424, 0x9901),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9500A USB Ethernet Device (SAL10) */
+ USB_DEVICE(0x0424, 0x9902),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9505A USB Ethernet Device (SAL10) */
+ USB_DEVICE(0x0424, 0x9903),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9512/9514 USB Hub & Ethernet Device (SAL10) */
+ USB_DEVICE(0x0424, 0x9904),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9500A USB Ethernet Device (HAL) */
+ USB_DEVICE(0x0424, 0x9905),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9505A USB Ethernet Device (HAL) */
+ USB_DEVICE(0x0424, 0x9906),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9500 USB Ethernet Device (Alternate ID) */
+ USB_DEVICE(0x0424, 0x9907),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9500A USB Ethernet Device (Alternate ID) */
+ USB_DEVICE(0x0424, 0x9908),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
+ {
+ /* SMSC9512/9514 USB Hub & Ethernet Device (Alternate ID) */
+ USB_DEVICE(0x0424, 0x9909),
+ .driver_info = (unsigned long) &smsc95xx_info,
+ },
{ }, /* END */
};
MODULE_DEVICE_TABLE(usb, products);
* NOTE: strictly conforming cdc-ether devices should expect
* the ZLP here, but ignore the one-byte packet.
*/
- if ((length % dev->maxpacket) == 0) {
+ if (!(info->flags & FLAG_SEND_ZLP) && (length % dev->maxpacket) == 0) {
urb->transfer_buffer_length++;
if (skb_tailroom(skb)) {
skb->data[skb->len] = 0;
-/* A simple network driver using virtio.
+/* A network driver using virtio.
*
* Copyright 2007 Rusty Russell <rusty@rustcorp.com.au> IBM Corporation
*
struct napi_struct napi;
unsigned int status;
- /* The skb we couldn't send because buffers were full. */
- struct sk_buff *last_xmit_skb;
-
- /* If we need to free in a timer, this is it. */
- struct timer_list xmit_free_timer;
-
/* Number of input buffers, and max we've ever had. */
unsigned int num, max;
- /* For cleaning up after transmission. */
- struct tasklet_struct tasklet;
- bool free_in_tasklet;
-
/* I like... big packets and I cannot lie! */
bool big_packets;
struct page *pages;
};
-static inline void *skb_vnet_hdr(struct sk_buff *skb)
+struct skb_vnet_hdr {
+ union {
+ struct virtio_net_hdr hdr;
+ struct virtio_net_hdr_mrg_rxbuf mhdr;
+ };
+ unsigned int num_sg;
+};
+
+static inline struct skb_vnet_hdr *skb_vnet_hdr(struct sk_buff *skb)
{
- return (struct virtio_net_hdr *)skb->cb;
+ return (struct skb_vnet_hdr *)skb->cb;
}
static void give_a_page(struct virtnet_info *vi, struct page *page)
/* We were probably waiting for more output buffers. */
netif_wake_queue(vi->dev);
-
- /* Make sure we re-xmit last_xmit_skb: if there are no more packets
- * queued, start_xmit won't be called. */
- tasklet_schedule(&vi->tasklet);
}
static void receive_skb(struct net_device *dev, struct sk_buff *skb,
unsigned len)
{
struct virtnet_info *vi = netdev_priv(dev);
- struct virtio_net_hdr *hdr = skb_vnet_hdr(skb);
+ struct skb_vnet_hdr *hdr = skb_vnet_hdr(skb);
int err;
int i;
}
if (vi->mergeable_rx_bufs) {
- struct virtio_net_hdr_mrg_rxbuf *mhdr = skb_vnet_hdr(skb);
unsigned int copy;
char *p = page_address(skb_shinfo(skb)->frags[0].page);
len = PAGE_SIZE;
len -= sizeof(struct virtio_net_hdr_mrg_rxbuf);
- memcpy(hdr, p, sizeof(*mhdr));
- p += sizeof(*mhdr);
+ memcpy(&hdr->mhdr, p, sizeof(hdr->mhdr));
+ p += sizeof(hdr->mhdr);
copy = len;
if (copy > skb_tailroom(skb))
skb_shinfo(skb)->nr_frags--;
} else {
skb_shinfo(skb)->frags[0].page_offset +=
- sizeof(*mhdr) + copy;
+ sizeof(hdr->mhdr) + copy;
skb_shinfo(skb)->frags[0].size = len;
skb->data_len += len;
skb->len += len;
}
- while (--mhdr->num_buffers) {
+ while (--hdr->mhdr.num_buffers) {
struct sk_buff *nskb;
i = skb_shinfo(skb)->nr_frags;
nskb = vi->rvq->vq_ops->get_buf(vi->rvq, &len);
if (!nskb) {
pr_debug("%s: rx error: %d buffers missing\n",
- dev->name, mhdr->num_buffers);
+ dev->name, hdr->mhdr.num_buffers);
dev->stats.rx_length_errors++;
goto drop;
}
skb->len += len;
}
} else {
- len -= sizeof(struct virtio_net_hdr);
+ len -= sizeof(hdr->hdr);
if (len <= MAX_PACKET_LEN)
trim_pages(vi, skb);
dev->stats.rx_bytes += skb->len;
dev->stats.rx_packets++;
- if (hdr->flags & VIRTIO_NET_HDR_F_NEEDS_CSUM) {
+ if (hdr->hdr.flags & VIRTIO_NET_HDR_F_NEEDS_CSUM) {
pr_debug("Needs csum!\n");
- if (!skb_partial_csum_set(skb,hdr->csum_start,hdr->csum_offset))
+ if (!skb_partial_csum_set(skb,
+ hdr->hdr.csum_start,
+ hdr->hdr.csum_offset))
goto frame_err;
}
pr_debug("Receiving skb proto 0x%04x len %i type %i\n",
ntohs(skb->protocol), skb->len, skb->pkt_type);
- if (hdr->gso_type != VIRTIO_NET_HDR_GSO_NONE) {
+ if (hdr->hdr.gso_type != VIRTIO_NET_HDR_GSO_NONE) {
pr_debug("GSO!\n");
- switch (hdr->gso_type & ~VIRTIO_NET_HDR_GSO_ECN) {
+ switch (hdr->hdr.gso_type & ~VIRTIO_NET_HDR_GSO_ECN) {
case VIRTIO_NET_HDR_GSO_TCPV4:
skb_shinfo(skb)->gso_type = SKB_GSO_TCPV4;
break;
default:
if (net_ratelimit())
printk(KERN_WARNING "%s: bad gso type %u.\n",
- dev->name, hdr->gso_type);
+ dev->name, hdr->hdr.gso_type);
goto frame_err;
}
- if (hdr->gso_type & VIRTIO_NET_HDR_GSO_ECN)
+ if (hdr->hdr.gso_type & VIRTIO_NET_HDR_GSO_ECN)
skb_shinfo(skb)->gso_type |= SKB_GSO_TCP_ECN;
- skb_shinfo(skb)->gso_size = hdr->gso_size;
+ skb_shinfo(skb)->gso_size = hdr->hdr.gso_size;
if (skb_shinfo(skb)->gso_size == 0) {
if (net_ratelimit())
printk(KERN_WARNING "%s: zero gso size.\n",
bool oom = false;
sg_init_table(sg, 2+MAX_SKB_FRAGS);
- for (;;) {
- struct virtio_net_hdr *hdr;
+ do {
+ struct skb_vnet_hdr *hdr;
skb = netdev_alloc_skb(vi->dev, MAX_PACKET_LEN + NET_IP_ALIGN);
if (unlikely(!skb)) {
skb_put(skb, MAX_PACKET_LEN);
hdr = skb_vnet_hdr(skb);
- sg_set_buf(sg, hdr, sizeof(*hdr));
+ sg_set_buf(sg, &hdr->hdr, sizeof(hdr->hdr));
if (vi->big_packets) {
for (i = 0; i < MAX_SKB_FRAGS; i++) {
break;
}
vi->num++;
- }
+ } while (err >= num);
if (unlikely(vi->num > vi->max))
vi->max = vi->num;
vi->rvq->vq_ops->kick(vi->rvq);
if (!vi->mergeable_rx_bufs)
return try_fill_recv_maxbufs(vi, gfp);
- for (;;) {
+ do {
skb_frag_t *f;
skb = netdev_alloc_skb(vi->dev, GOOD_COPY_LEN + NET_IP_ALIGN);
break;
}
vi->num++;
- }
+ } while (err > 0);
if (unlikely(vi->num > vi->max))
vi->max = vi->num;
vi->rvq->vq_ops->kick(vi->rvq);
return received;
}
-static void free_old_xmit_skbs(struct virtnet_info *vi)
+static unsigned int free_old_xmit_skbs(struct virtnet_info *vi)
{
struct sk_buff *skb;
- unsigned int len;
+ unsigned int len, tot_sgs = 0;
while ((skb = vi->svq->vq_ops->get_buf(vi->svq, &len)) != NULL) {
pr_debug("Sent skb %p\n", skb);
__skb_unlink(skb, &vi->send);
vi->dev->stats.tx_bytes += skb->len;
vi->dev->stats.tx_packets++;
+ tot_sgs += skb_vnet_hdr(skb)->num_sg;
kfree_skb(skb);
}
-}
-
-/* If the virtio transport doesn't always notify us when all in-flight packets
- * are consumed, we fall back to using this function on a timer to free them. */
-static void xmit_free(unsigned long data)
-{
- struct virtnet_info *vi = (void *)data;
-
- netif_tx_lock(vi->dev);
-
- free_old_xmit_skbs(vi);
-
- if (!skb_queue_empty(&vi->send))
- mod_timer(&vi->xmit_free_timer, jiffies + (HZ/10));
-
- netif_tx_unlock(vi->dev);
+ return tot_sgs;
}
static int xmit_skb(struct virtnet_info *vi, struct sk_buff *skb)
{
- int num, err;
struct scatterlist sg[2+MAX_SKB_FRAGS];
- struct virtio_net_hdr_mrg_rxbuf *mhdr = skb_vnet_hdr(skb);
- struct virtio_net_hdr *hdr = skb_vnet_hdr(skb);
+ struct skb_vnet_hdr *hdr = skb_vnet_hdr(skb);
const unsigned char *dest = ((struct ethhdr *)skb->data)->h_dest;
sg_init_table(sg, 2+MAX_SKB_FRAGS);
pr_debug("%s: xmit %p %pM\n", vi->dev->name, skb, dest);
if (skb->ip_summed == CHECKSUM_PARTIAL) {
- hdr->flags = VIRTIO_NET_HDR_F_NEEDS_CSUM;
- hdr->csum_start = skb->csum_start - skb_headroom(skb);
- hdr->csum_offset = skb->csum_offset;
+ hdr->hdr.flags = VIRTIO_NET_HDR_F_NEEDS_CSUM;
+ hdr->hdr.csum_start = skb->csum_start - skb_headroom(skb);
+ hdr->hdr.csum_offset = skb->csum_offset;
} else {
- hdr->flags = 0;
- hdr->csum_offset = hdr->csum_start = 0;
+ hdr->hdr.flags = 0;
+ hdr->hdr.csum_offset = hdr->hdr.csum_start = 0;
}
if (skb_is_gso(skb)) {
- hdr->hdr_len = skb_headlen(skb);
- hdr->gso_size = skb_shinfo(skb)->gso_size;
+ hdr->hdr.hdr_len = skb_headlen(skb);
+ hdr->hdr.gso_size = skb_shinfo(skb)->gso_size;
if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4)
- hdr->gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
+ hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
else if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6)
- hdr->gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
+ hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
else if (skb_shinfo(skb)->gso_type & SKB_GSO_UDP)
- hdr->gso_type = VIRTIO_NET_HDR_GSO_UDP;
+ hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_UDP;
else
BUG();
if (skb_shinfo(skb)->gso_type & SKB_GSO_TCP_ECN)
- hdr->gso_type |= VIRTIO_NET_HDR_GSO_ECN;
+ hdr->hdr.gso_type |= VIRTIO_NET_HDR_GSO_ECN;
} else {
- hdr->gso_type = VIRTIO_NET_HDR_GSO_NONE;
- hdr->gso_size = hdr->hdr_len = 0;
+ hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_NONE;
+ hdr->hdr.gso_size = hdr->hdr.hdr_len = 0;
}
- mhdr->num_buffers = 0;
+ hdr->mhdr.num_buffers = 0;
/* Encode metadata header at front. */
if (vi->mergeable_rx_bufs)
- sg_set_buf(sg, mhdr, sizeof(*mhdr));
+ sg_set_buf(sg, &hdr->mhdr, sizeof(hdr->mhdr));
else
- sg_set_buf(sg, hdr, sizeof(*hdr));
+ sg_set_buf(sg, &hdr->hdr, sizeof(hdr->hdr));
- num = skb_to_sgvec(skb, sg+1, 0, skb->len) + 1;
-
- err = vi->svq->vq_ops->add_buf(vi->svq, sg, num, 0, skb);
- if (err >= 0 && !vi->free_in_tasklet)
- mod_timer(&vi->xmit_free_timer, jiffies + (HZ/10));
-
- return err;
-}
-
-static void xmit_tasklet(unsigned long data)
-{
- struct virtnet_info *vi = (void *)data;
-
- netif_tx_lock_bh(vi->dev);
- if (vi->last_xmit_skb && xmit_skb(vi, vi->last_xmit_skb) >= 0) {
- vi->svq->vq_ops->kick(vi->svq);
- vi->last_xmit_skb = NULL;
- }
- if (vi->free_in_tasklet)
- free_old_xmit_skbs(vi);
- netif_tx_unlock_bh(vi->dev);
+ hdr->num_sg = skb_to_sgvec(skb, sg+1, 0, skb->len) + 1;
+ return vi->svq->vq_ops->add_buf(vi->svq, sg, hdr->num_sg, 0, skb);
}
static netdev_tx_t start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct virtnet_info *vi = netdev_priv(dev);
+ int capacity;
again:
/* Free up any pending old buffers before queueing new ones. */
free_old_xmit_skbs(vi);
- /* If we has a buffer left over from last time, send it now. */
- if (unlikely(vi->last_xmit_skb) &&
- xmit_skb(vi, vi->last_xmit_skb) < 0)
- goto stop_queue;
-
- vi->last_xmit_skb = NULL;
-
/* Put new one in send queue and do transmit */
- if (likely(skb)) {
- __skb_queue_head(&vi->send, skb);
- if (xmit_skb(vi, skb) < 0) {
- vi->last_xmit_skb = skb;
- skb = NULL;
- goto stop_queue;
+ __skb_queue_head(&vi->send, skb);
+ capacity = xmit_skb(vi, skb);
+
+ /* This can happen with OOM and indirect buffers. */
+ if (unlikely(capacity < 0)) {
+ netif_stop_queue(dev);
+ dev_warn(&dev->dev, "Unexpected full queue\n");
+ if (unlikely(!vi->svq->vq_ops->enable_cb(vi->svq))) {
+ vi->svq->vq_ops->disable_cb(vi->svq);
+ netif_start_queue(dev);
+ goto again;
}
+ return NETDEV_TX_BUSY;
}
-done:
- vi->svq->vq_ops->kick(vi->svq);
- return NETDEV_TX_OK;
-stop_queue:
- pr_debug("%s: virtio not prepared to send\n", dev->name);
- netif_stop_queue(dev);
-
- /* Activate callback for using skbs: if this returns false it
- * means some were used in the meantime. */
- if (unlikely(!vi->svq->vq_ops->enable_cb(vi->svq))) {
- vi->svq->vq_ops->disable_cb(vi->svq);
- netif_start_queue(dev);
- goto again;
- }
- if (skb) {
- /* Drop this skb: we only queue one. */
- vi->dev->stats.tx_dropped++;
- kfree_skb(skb);
+ vi->svq->vq_ops->kick(vi->svq);
+ /* Don't wait up for transmitted skbs to be freed. */
+ skb_orphan(skb);
+ nf_reset(skb);
+
+ /* Apparently nice girls don't return TX_BUSY; stop the queue
+ * before it gets out of hand. Naturally, this wastes entries. */
+ if (capacity < 2+MAX_SKB_FRAGS) {
+ netif_stop_queue(dev);
+ if (unlikely(!vi->svq->vq_ops->enable_cb(vi->svq))) {
+ /* More just got used, free them then recheck. */
+ capacity += free_old_xmit_skbs(vi);
+ if (capacity >= 2+MAX_SKB_FRAGS) {
+ netif_start_queue(dev);
+ vi->svq->vq_ops->disable_cb(vi->svq);
+ }
+ }
}
- goto done;
+
+ return NETDEV_TX_OK;
}
static int virtnet_set_mac_address(struct net_device *dev, void *p)
vi->pages = NULL;
INIT_DELAYED_WORK(&vi->refill, refill_work);
- /* If they give us a callback when all buffers are done, we don't need
- * the timer. */
- vi->free_in_tasklet = virtio_has_feature(vdev,VIRTIO_F_NOTIFY_ON_EMPTY);
-
/* If we can receive ANY GSO packets, we must allocate large ones. */
if (virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO4)
|| virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO6)
skb_queue_head_init(&vi->recv);
skb_queue_head_init(&vi->send);
- tasklet_init(&vi->tasklet, xmit_tasklet, (unsigned long)vi);
-
- if (!vi->free_in_tasklet)
- setup_timer(&vi->xmit_free_timer, xmit_free, (unsigned long)vi);
-
err = register_netdev(dev);
if (err) {
pr_debug("virtio_net: registering device failed\n");
return err;
}
-static void virtnet_remove(struct virtio_device *vdev)
+static void __devexit virtnet_remove(struct virtio_device *vdev)
{
struct virtnet_info *vi = vdev->priv;
struct sk_buff *skb;
/* Stop all the virtqueues. */
vdev->config->reset(vdev);
- if (!vi->free_in_tasklet)
- del_timer_sync(&vi->xmit_free_timer);
-
/* Free our skbs in send and recv queues, if any. */
while ((skb = __skb_dequeue(&vi->recv)) != NULL) {
kfree_skb(skb);
VIRTIO_NET_F_GUEST_ECN, VIRTIO_NET_F_GUEST_UFO,
VIRTIO_NET_F_MRG_RXBUF, VIRTIO_NET_F_STATUS, VIRTIO_NET_F_CTRL_VQ,
VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN,
- VIRTIO_F_NOTIFY_ON_EMPTY,
};
static struct virtio_driver virtio_net = {
---help---
Say Y if you have a Metricom radio and intend to use Starmode Radio
IP. STRIP is a radio protocol developed for the MosquitoNet project
- (on the WWW at <http://mosquitonet.stanford.edu/>) to send Internet
- traffic using Metricom radios. Metricom radios are small, battery
- powered, 100kbit/sec packet radio transceivers, about the size and
- weight of a cellular telephone. (You may also have heard them called
- "Metricom modems" but we avoid the term "modem" because it misleads
- many people into thinking that you can plug a Metricom modem into a
- phone line and use it as a modem.)
+ to send Internet traffic using Metricom radios. Metricom radios are
+ small, battery powered, 100kbit/sec packet radio transceivers, about
+ the size and weight of a cellular telephone. (You may also have heard
+ them called "Metricom modems" but we avoid the term "modem" because
+ it misleads many people into thinking that you can plug a Metricom
+ modem into a phone line and use it as a modem.)
You can use STRIP on any Linux machine with a serial port, although
it is obviously most useful for people with laptop computers. If you
static char arlan_drive_info[ARLAN_STR_SIZE] = "A655\n\0";
-static int arlan_sysctl_info(ctl_table * ctl, int write, struct file *filp,
+static int arlan_sysctl_info(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int i;
*lenp = pos;
if (!write)
- retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ retv = proc_dostring(ctl, write, buffer, lenp, ppos);
else
{
*lenp = 0;
}
-static int arlan_sysctl_info161719(ctl_table * ctl, int write, struct file *filp,
+static int arlan_sysctl_info161719(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int i;
final:
*lenp = pos;
- retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ retv = proc_dostring(ctl, write, buffer, lenp, ppos);
return retv;
}
-static int arlan_sysctl_infotxRing(ctl_table * ctl, int write, struct file *filp,
+static int arlan_sysctl_infotxRing(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int i;
SARLBNpln(u_char, txBuffer, 0x800);
final:
*lenp = pos;
- retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ retv = proc_dostring(ctl, write, buffer, lenp, ppos);
return retv;
}
-static int arlan_sysctl_inforxRing(ctl_table * ctl, int write, struct file *filp,
+static int arlan_sysctl_inforxRing(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int i;
SARLBNpln(u_char, rxBuffer, 0x800);
final:
*lenp = pos;
- retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ retv = proc_dostring(ctl, write, buffer, lenp, ppos);
return retv;
}
-static int arlan_sysctl_info18(ctl_table * ctl, int write, struct file *filp,
+static int arlan_sysctl_info18(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int i;
final:
*lenp = pos;
- retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ retv = proc_dostring(ctl, write, buffer, lenp, ppos);
return retv;
}
static char conf_reset_result[200];
-static int arlan_configure(ctl_table * ctl, int write, struct file *filp,
+static int arlan_configure(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int pos = 0;
return -1;
*lenp = pos;
- return proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ return proc_dostring(ctl, write, buffer, lenp, ppos);
}
-static int arlan_sysctl_reset(ctl_table * ctl, int write, struct file *filp,
+static int arlan_sysctl_reset(ctl_table * ctl, int write,
void __user *buffer, size_t * lenp, loff_t *ppos)
{
int pos = 0;
} else
return -1;
*lenp = pos + 3;
- return proc_dostring(ctl, write, filp, buffer, lenp, ppos);
+ return proc_dostring(ctl, write, buffer, lenp, ppos);
}
u8 vpds[2][AR5416_PD_GAIN_ICEPTS];
u8 pwrs[2][AR5416_PD_GAIN_ICEPTS];
int chain, idx, i;
- u8 f;
+ u32 phy_data = 0;
+ u8 f, tmp;
switch (channel->band) {
case IEEE80211_BAND_2GHZ:
}
for (i = 0; i < 76; i++) {
- u32 phy_data;
- u8 tmp;
-
if (i < 25) {
tmp = ar9170_interpolate_val(i, &pwrs[0][0],
&vpds[0][0]);
{ USB_DEVICE(0x0cf3, 0x9170) },
/* Atheros TG121N */
{ USB_DEVICE(0x0cf3, 0x1001) },
+ /* TP-Link TL-WN821N v2 */
+ { USB_DEVICE(0x0cf3, 0x1002) },
/* Cace Airpcap NX */
{ USB_DEVICE(0xcace, 0x0300) },
/* D-Link DWA 160A */
AR_PHY_CH1_EXT_CCA,
AR_PHY_CH2_EXT_CCA
};
- u8 chainmask;
+ u8 chainmask, rx_chain_status;
+ rx_chain_status = REG_READ(ah, AR_PHY_RX_CHAINMASK);
if (AR_SREV_9285(ah))
chainmask = 0x9;
- else if (AR_SREV_9280(ah) || AR_SREV_9287(ah))
- chainmask = 0x1B;
- else
- chainmask = 0x3F;
+ else if (AR_SREV_9280(ah) || AR_SREV_9287(ah)) {
+ if ((rx_chain_status & 0x2) || (rx_chain_status & 0x4))
+ chainmask = 0x1B;
+ else
+ chainmask = 0x09;
+ } else {
+ if (rx_chain_status & 0x4)
+ chainmask = 0x3F;
+ else if (rx_chain_status & 0x2)
+ chainmask = 0x1B;
+ else
+ chainmask = 0x09;
+ }
h = ah->nfCalHist;
noise_floor = AR_PHY_CCA_MAX_AR9280_GOOD_VALUE;
else if (AR_SREV_9285(ah))
noise_floor = AR_PHY_CCA_MAX_AR9285_GOOD_VALUE;
+ else if (AR_SREV_9287(ah))
+ noise_floor = AR_PHY_CCA_MAX_AR9287_GOOD_VALUE;
else
noise_floor = AR_PHY_CCA_MAX_AR5416_GOOD_VALUE;
regVal |= (1 << (19 + i));
REG_WRITE(ah, 0x7834, regVal);
udelay(1);
+ regVal = REG_READ(ah, 0x7834);
regVal &= (~(0x1 << (19 + i)));
reg_field = MS(REG_READ(ah, 0x7840), AR9285_AN_RXTXBB1_SPARE9);
regVal |= (reg_field << (19 + i));
#define AR_PHY_CCA_MAX_AR5416_GOOD_VALUE -85
#define AR_PHY_CCA_MAX_AR9280_GOOD_VALUE -112
#define AR_PHY_CCA_MAX_AR9285_GOOD_VALUE -118
+#define AR_PHY_CCA_MAX_AR9287_GOOD_VALUE -118
#define AR_PHY_CCA_MAX_HIGH_VALUE -62
#define AR_PHY_CCA_MIN_BAD_VALUE -140
#define AR_PHY_CCA_FILTERWINDOW_LENGTH_INIT 3
REG_RMW_FIELD(ah, AR_AN_TOP1, AR_AN_TOP1_DACIPMODE,
eep->baseEepHeader.dacLpMode);
+ udelay(100);
+
REG_RMW_FIELD(ah, AR_PHY_FRAME_CTL, AR_PHY_FRAME_CTL_TX_CLIP,
pModal->miscBits >> 2);
u16 powerLimit)
{
#define REDUCE_SCALED_POWER_BY_TWO_CHAIN 6 /* 10*log10(2)*2 */
-#define REDUCE_SCALED_POWER_BY_THREE_CHAIN 10 /* 10*log10(3)*2 */
+#define REDUCE_SCALED_POWER_BY_THREE_CHAIN 9 /* 10*log10(3)*2 */
struct ath_regulatory *regulatory = ath9k_hw_regulatory(ah);
struct ar5416_eeprom_def *pEepData = &ah->eeprom.def;
static void ath9k_hw_init_mode_gain_regs(struct ath_hw *ah)
{
- if (AR_SREV_9287_11(ah))
+ if (AR_SREV_9287_11_OR_LATER(ah))
INIT_INI_ARRAY(&ah->iniModesRxGain,
ar9287Modes_rx_gain_9287_1_1,
ARRAY_SIZE(ar9287Modes_rx_gain_9287_1_1), 6);
else if (AR_SREV_9280_20(ah))
ath9k_hw_init_rxgain_ini(ah);
- if (AR_SREV_9287_11(ah)) {
+ if (AR_SREV_9287_11_OR_LATER(ah)) {
INIT_INI_ARRAY(&ah->iniModesTxGain,
ar9287Modes_tx_gain_9287_1_1,
ARRAY_SIZE(ar9287Modes_tx_gain_9287_1_1), 6);
ath9k_hw_init_mode_regs(ah);
if (ah->is_pciexpress)
- ath9k_hw_configpcipowersave(ah, 0);
+ ath9k_hw_configpcipowersave(ah, 0, 0);
else
ath9k_hw_disablepcie(ah);
*/
REG_SET_BIT(ah, AR_DIAG_SW, (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT));
+ if (AR_SREV_9280_10_OR_LATER(ah)) {
+ val = REG_READ(ah, AR_PCU_MISC_MODE2) &
+ (~AR_PCU_MISC_MODE2_HWWAR1);
+
+ if (AR_SREV_9287_10_OR_LATER(ah))
+ val = val & (~AR_PCU_MISC_MODE2_HWWAR2);
+
+ REG_WRITE(ah, AR_PCU_MISC_MODE2, val);
+ }
if (!AR_SREV_5416_20_OR_LATER(ah) ||
AR_SREV_9280_10_OR_LATER(ah))
static bool ath9k_hw_chip_reset(struct ath_hw *ah,
struct ath9k_channel *chan)
{
- if (OLC_FOR_AR9280_20_LATER) {
+ if (AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL)) {
if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_POWER_ON))
return false;
} else if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_WARM))
struct ath9k_channel *curchan = ah->curchan;
u32 saveDefAntenna;
u32 macStaId1;
+ u64 tsf = 0;
int i, rx_chainmask, r;
ah->extprotspacing = sc->ht_extprotspacing;
if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE))
return -EIO;
- if (curchan)
+ if (curchan && !ah->chip_fullsleep)
ath9k_hw_getnf(ah, curchan);
if (bChannelChange &&
(chan->channel != ah->curchan->channel) &&
((chan->channelFlags & CHANNEL_ALL) ==
(ah->curchan->channelFlags & CHANNEL_ALL)) &&
- (!AR_SREV_9280(ah) || (!IS_CHAN_A_5MHZ_SPACED(chan) &&
- !IS_CHAN_A_5MHZ_SPACED(ah->curchan)))) {
+ !(AR_SREV_9280(ah) || IS_CHAN_A_5MHZ_SPACED(chan) ||
+ IS_CHAN_A_5MHZ_SPACED(ah->curchan))) {
if (ath9k_hw_channel_change(ah, chan, sc->tx_chan_width)) {
ath9k_hw_loadnf(ah, ah->curchan);
macStaId1 = REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_BASE_RATE_11B;
+ /* For chips on which RTC reset is done, save TSF before it gets cleared */
+ if (AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL))
+ tsf = ath9k_hw_gettsf64(ah);
+
saveLedState = REG_READ(ah, AR_CFG_LED) &
(AR_CFG_LED_ASSOC_CTL | AR_CFG_LED_MODE_SEL |
AR_CFG_LED_BLINK_THRESH_SEL | AR_CFG_LED_BLINK_SLOW);
udelay(50);
}
+ /* Restore TSF */
+ if (tsf && AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL))
+ ath9k_hw_settsf64(ah, tsf);
+
if (AR_SREV_9280_10_OR_LATER(ah))
REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL, AR_GPIO_JTAG_DISABLE);
* Programming the SerDes must go through the same 288 bit serial shift
* register as the other analog registers. Hence the 9 writes.
*/
-void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore)
+void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore, int power_off)
{
u8 i;
+ u32 val;
if (ah->is_pciexpress != true)
return;
return;
/* Nothing to do on restore for 11N */
- if (restore)
- return;
+ if (!restore) {
+ if (AR_SREV_9280_20_OR_LATER(ah)) {
+ /*
+ * AR9280 2.0 or later chips use SerDes values from the
+ * initvals.h initialized depending on chipset during
+ * ath9k_hw_init()
+ */
+ for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) {
+ REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0),
+ INI_RA(&ah->iniPcieSerdes, i, 1));
+ }
+ } else if (AR_SREV_9280(ah) &&
+ (ah->hw_version.macRev == AR_SREV_REVISION_9280_10)) {
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+
+ /* RX shut off when elecidle is asserted */
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560);
+
+ /* Shut off CLKREQ active in L1 */
+ if (ah->config.pcie_clock_req)
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc);
+ else
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd);
- if (AR_SREV_9280_20_OR_LATER(ah)) {
- /*
- * AR9280 2.0 or later chips use SerDes values from the
- * initvals.h initialized depending on chipset during
- * ath9k_hw_init()
- */
- for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) {
- REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0),
- INI_RA(&ah->iniPcieSerdes, i, 1));
- }
- } else if (AR_SREV_9280(ah) &&
- (ah->hw_version.macRev == AR_SREV_REVISION_9280_10)) {
- REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00);
- REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007);
- /* RX shut off when elecidle is asserted */
- REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019);
- REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820);
- REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560);
+ /* Load the new settings */
+ REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
- /* Shut off CLKREQ active in L1 */
- if (ah->config.pcie_clock_req)
- REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc);
- else
- REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd);
-
- REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
- REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
- REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007);
+ } else {
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
- /* Load the new settings */
- REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+ /* RX shut off when elecidle is asserted */
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
- } else {
- REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00);
- REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924);
+ /*
+ * Ignore ah->ah_config.pcie_clock_req setting for
+ * pre-AR9280 11n
+ */
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
- /* RX shut off when elecidle is asserted */
- REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039);
- REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824);
- REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
+ REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
- /*
- * Ignore ah->ah_config.pcie_clock_req setting for
- * pre-AR9280 11n
- */
- REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff);
+ /* Load the new settings */
+ REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
+ }
- REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40);
- REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554);
- REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007);
+ udelay(1000);
- /* Load the new settings */
- REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000);
- }
+ /* set bit 19 to allow forcing of pcie core into L1 state */
+ REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
- udelay(1000);
+ /* Several PCIe massages to ensure proper behaviour */
+ if (ah->config.pcie_waen) {
+ val = ah->config.pcie_waen;
+ if (!power_off)
+ val &= (~AR_WA_D3_L1_DISABLE);
+ } else {
+ if (AR_SREV_9285(ah) || AR_SREV_9271(ah) ||
+ AR_SREV_9287(ah)) {
+ val = AR9285_WA_DEFAULT;
+ if (!power_off)
+ val &= (~AR_WA_D3_L1_DISABLE);
+ } else if (AR_SREV_9280(ah)) {
+ /*
+ * On AR9280 chips bit 22 of 0x4004 needs to be
+ * set otherwise card may disappear.
+ */
+ val = AR9280_WA_DEFAULT;
+ if (!power_off)
+ val &= (~AR_WA_D3_L1_DISABLE);
+ } else
+ val = AR_WA_DEFAULT;
+ }
- /* set bit 19 to allow forcing of pcie core into L1 state */
- REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA);
+ REG_WRITE(ah, AR_WA, val);
+ }
- /* Several PCIe massages to ensure proper behaviour */
- if (ah->config.pcie_waen) {
- REG_WRITE(ah, AR_WA, ah->config.pcie_waen);
- } else {
- if (AR_SREV_9285(ah) || AR_SREV_9271(ah) || AR_SREV_9287(ah))
- REG_WRITE(ah, AR_WA, AR9285_WA_DEFAULT);
+ if (power_off) {
/*
- * On AR9280 chips bit 22 of 0x4004 needs to be set to
- * otherwise card may disappear.
+ * Set PCIe workaround bits
+ * bit 14 in WA register (disable L1) should only
+ * be set when device enters D3 and be cleared
+ * when device comes back to D0.
*/
- else if (AR_SREV_9280(ah))
- REG_WRITE(ah, AR_WA, AR9280_WA_DEFAULT);
- else
- REG_WRITE(ah, AR_WA, AR_WA_DEFAULT);
+ if (ah->config.pcie_waen) {
+ if (ah->config.pcie_waen & AR_WA_D3_L1_DISABLE)
+ REG_SET_BIT(ah, AR_WA, AR_WA_D3_L1_DISABLE);
+ } else {
+ if (((AR_SREV_9285(ah) || AR_SREV_9271(ah) ||
+ AR_SREV_9287(ah)) &&
+ (AR9285_WA_DEFAULT & AR_WA_D3_L1_DISABLE)) ||
+ (AR_SREV_9280(ah) &&
+ (AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE))) {
+ REG_SET_BIT(ah, AR_WA, AR_WA_D3_L1_DISABLE);
+ }
+ }
}
}
}
#endif
- if ((ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCI) ||
- (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE) ||
- (ah->hw_version.macVersion == AR_SREV_VERSION_9160) ||
- (ah->hw_version.macVersion == AR_SREV_VERSION_9100) ||
- (ah->hw_version.macVersion == AR_SREV_VERSION_9280) ||
- (ah->hw_version.macVersion == AR_SREV_VERSION_9285))
- pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP;
- else
- pCap->hw_caps |= ATH9K_HW_CAP_AUTOSLEEP;
+ pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP;
if (AR_SREV_9280(ah) || AR_SREV_9285(ah))
pCap->hw_caps &= ~ATH9K_HW_CAP_4KB_SPLITTRANS;
#define AH_TSF_WRITE_TIMEOUT 100 /* (us) */
#define AH_TIME_QUANTUM 10
#define AR_KEYTABLE_SIZE 128
-#define POWER_UP_TIME 200000
+#define POWER_UP_TIME 10000
#define SPUR_RSSI_THRESH 40
#define CAB_TIMEOUT_VAL 10
const struct ath9k_beacon_state *bs);
bool ath9k_hw_setpower(struct ath_hw *ah,
enum ath9k_power_mode mode);
-void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore);
+void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore, int power_off);
/* Interrupt Handling */
bool ath9k_hw_intrpend(struct ath_hw *ah);
int r;
ath9k_ps_wakeup(sc);
- ath9k_hw_configpcipowersave(ah, 0);
+ ath9k_hw_configpcipowersave(ah, 0, 0);
if (!ah->curchan)
ah->curchan = ath_get_curchannel(sc, sc->hw);
spin_unlock_bh(&sc->sc_resetlock);
ath9k_hw_phy_disable(ah);
- ath9k_hw_configpcipowersave(ah, 1);
+ ath9k_hw_configpcipowersave(ah, 1, 1);
ath9k_ps_restore(sc);
ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP);
}
bool blocked = !!ath_is_rfkill_set(sc);
wiphy_rfkill_set_hw_state(hw->wiphy, blocked);
-
- if (blocked)
- ath_radio_disable(sc);
- else
- ath_radio_enable(sc);
}
static void ath_start_rfkill_poll(struct ath_softc *sc)
DPRINTF(sc, ATH_DBG_CONFIG, "Detach ATH hw\n");
ath_deinit_leds(sc);
+ wiphy_rfkill_stop_polling(sc->hw->wiphy);
for (i = 0; i < sc->num_sec_wiphy; i++) {
struct ath_wiphy *aphy = sc->sec_wiphy[i];
init_channel = ath_get_curchannel(sc, hw);
/* Reset SERDES registers */
- ath9k_hw_configpcipowersave(sc->sc_ah, 0);
+ ath9k_hw_configpcipowersave(sc->sc_ah, 0, 0);
/*
* The basic interface to setting the hardware in a good
} else
sc->rx.rxlink = NULL;
- wiphy_rfkill_stop_polling(sc->hw->wiphy);
-
/* disable HAL and put h/w to sleep */
ath9k_hw_disable(sc->sc_ah);
- ath9k_hw_configpcipowersave(sc->sc_ah, 1);
+ ath9k_hw_configpcipowersave(sc->sc_ah, 1, 1);
ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_FULL_SLEEP);
sc->sc_flags |= SC_OP_INVALID;
#define AR_RC_HOSTIF 0x00000100
#define AR_WA 0x4004
+#define AR_WA_D3_L1_DISABLE (1 << 14)
#define AR9285_WA_DEFAULT 0x004a05cb
-#define AR9280_WA_DEFAULT 0x0040073f
+#define AR9280_WA_DEFAULT 0x0040073b
#define AR_WA_DEFAULT 0x0000073f
If unsure, say N.
+config B43_SDIO
+ bool "Broadcom 43xx SDIO device support (EXPERIMENTAL)"
+ depends on B43 && SSB_SDIOHOST_POSSIBLE && EXPERIMENTAL
+ select SSB_SDIOHOST
+ ---help---
+ Broadcom 43xx device support for Soft-MAC SDIO devices.
+
+ With this config option you can drive Soft-MAC b43 cards with a
+ Secure Digital I/O interface.
+ This includes the WLAN daughter card found on the Nintendo Wii
+ video game console.
+ Note that this does not support Broadcom 43xx Full-MAC devices.
+
+ It's safe to select Y here, even if you don't have a B43 SDIO device.
+
+ If unsure, say N.
+
# Data transfers to the device via PIO
-# This is only needed on PCMCIA devices. All others can do DMA properly.
+# This is only needed on PCMCIA and SDIO devices. All others can do DMA properly.
config B43_PIO
bool
- depends on B43 && (B43_PCMCIA || B43_FORCE_PIO)
+ depends on B43 && (B43_SDIO || B43_PCMCIA || B43_FORCE_PIO)
select SSB_BLOCKIO
default y
b43-y += rfkill.o
b43-$(CONFIG_B43_LEDS) += leds.o
b43-$(CONFIG_B43_PCMCIA) += pcmcia.o
+b43-$(CONFIG_B43_SDIO) += sdio.o
b43-$(CONFIG_B43_DEBUG) += debugfs.o
obj-$(CONFIG_B43) += b43.o
* from the mac80211 subsystem. */
u16 mac80211_initially_registered_queues;
- /* R/W lock for data transmission.
- * Transmissions on 2+ queues can run concurrently, but somebody else
- * might sync with TX by write_lock_irqsave()'ing. */
- rwlock_t tx_lock;
- /* Lock for LEDs access. */
- spinlock_t leds_lock;
-
/* We can only have one operating interface (802.11 core)
* at a time. General information about this interface follows.
*/
struct work_struct tx_work;
/* Queue of packets to be transmitted. */
struct sk_buff_head tx_queue;
+
+ /* The device LEDs. */
+ struct b43_leds leds;
};
/* The type of the firmware file. */
/* The device initialization status.
* Use b43_status() to query. */
atomic_t __init_status;
- /* Saved init status for handling suspend. */
- int suspend_init_status;
bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */
bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */
bool radio_hw_enable; /* saved state of radio hardware enabled state */
- bool suspend_in_progress; /* TRUE, if we are in a suspend/resume cycle */
bool qos_enabled; /* TRUE, if QoS is used. */
bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */
/* Various statistics about the physical device. */
struct b43_stats stats;
- /* The device LEDs. */
- struct b43_led led_tx;
- struct b43_led led_rx;
- struct b43_led led_assoc;
- struct b43_led led_radio;
-
/* Reason code of the last interrupt. */
u32 irq_reason;
u32 dma_reason[6];
/* Debugging stuff follows. */
#ifdef CONFIG_B43_DEBUG
struct b43_dfsentry *dfsentry;
+ unsigned int irq_count;
+ unsigned int irq_bit_count[32];
+ unsigned int tx_count;
+ unsigned int rx_count;
#endif
};
add_dyn_dbg("debug_lo", B43_DBG_LO, 0);
add_dyn_dbg("debug_firmware", B43_DBG_FIRMWARE, 0);
add_dyn_dbg("debug_keys", B43_DBG_KEYS, 0);
+ add_dyn_dbg("debug_verbose_stats", B43_DBG_VERBOSESTATS, 0);
#undef add_dyn_dbg
}
B43_DBG_LO,
B43_DBG_FIRMWARE,
B43_DBG_KEYS,
+ B43_DBG_VERBOSESTATS,
__B43_NR_DYNDBG,
};
ring->nr_failed_tx_packets++;
ring->nr_total_packet_tries += status->frame_count;
#endif /* DEBUG */
- ieee80211_tx_status_irqsafe(dev->wl->hw, meta->skb);
+ ieee80211_tx_status(dev->wl->hw, meta->skb);
- /* skb is freed by ieee80211_tx_status_irqsafe() */
+ /* skb is freed by ieee80211_tx_status() */
meta->skb = NULL;
} else {
/* No need to call free_descriptor_buffer here, as
static void b43_led_turn_on(struct b43_wldev *dev, u8 led_index,
bool activelow)
{
- struct b43_wl *wl = dev->wl;
- unsigned long flags;
u16 ctl;
- spin_lock_irqsave(&wl->leds_lock, flags);
ctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
if (activelow)
ctl &= ~(1 << led_index);
else
ctl |= (1 << led_index);
b43_write16(dev, B43_MMIO_GPIO_CONTROL, ctl);
- spin_unlock_irqrestore(&wl->leds_lock, flags);
}
static void b43_led_turn_off(struct b43_wldev *dev, u8 led_index,
bool activelow)
{
- struct b43_wl *wl = dev->wl;
- unsigned long flags;
u16 ctl;
- spin_lock_irqsave(&wl->leds_lock, flags);
ctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL);
if (activelow)
ctl |= (1 << led_index);
else
ctl &= ~(1 << led_index);
b43_write16(dev, B43_MMIO_GPIO_CONTROL, ctl);
- spin_unlock_irqrestore(&wl->leds_lock, flags);
}
-/* Callback from the LED subsystem. */
-static void b43_led_brightness_set(struct led_classdev *led_dev,
- enum led_brightness brightness)
+static void b43_led_update(struct b43_wldev *dev,
+ struct b43_led *led)
{
- struct b43_led *led = container_of(led_dev, struct b43_led, led_dev);
- struct b43_wldev *dev = led->dev;
bool radio_enabled;
+ bool turn_on;
- if (unlikely(b43_status(dev) < B43_STAT_INITIALIZED))
+ if (!led->wl)
return;
- /* Checking the radio-enabled status here is slightly racy,
- * but we want to avoid the locking overhead and we don't care
- * whether the LED has the wrong state for a second. */
radio_enabled = (dev->phy.radio_on && dev->radio_hw_enable);
- if (brightness == LED_OFF || !radio_enabled)
- b43_led_turn_off(dev, led->index, led->activelow);
+ /* The led->state read is racy, but we don't care. In case we raced
+ * with the brightness_set handler, we will be called again soon
+ * to fixup our state. */
+ if (radio_enabled)
+ turn_on = atomic_read(&led->state) != LED_OFF;
else
+ turn_on = 0;
+ if (turn_on == led->hw_state)
+ return;
+ led->hw_state = turn_on;
+
+ if (turn_on)
b43_led_turn_on(dev, led->index, led->activelow);
+ else
+ b43_led_turn_off(dev, led->index, led->activelow);
+}
+
+static void b43_leds_work(struct work_struct *work)
+{
+ struct b43_leds *leds = container_of(work, struct b43_leds, work);
+ struct b43_wl *wl = container_of(leds, struct b43_wl, leds);
+ struct b43_wldev *dev;
+
+ mutex_lock(&wl->mutex);
+ dev = wl->current_dev;
+ if (unlikely(!dev || b43_status(dev) < B43_STAT_STARTED))
+ goto out_unlock;
+
+ b43_led_update(dev, &wl->leds.led_tx);
+ b43_led_update(dev, &wl->leds.led_rx);
+ b43_led_update(dev, &wl->leds.led_radio);
+ b43_led_update(dev, &wl->leds.led_assoc);
+
+out_unlock:
+ mutex_unlock(&wl->mutex);
+}
+
+/* Callback from the LED subsystem. */
+static void b43_led_brightness_set(struct led_classdev *led_dev,
+ enum led_brightness brightness)
+{
+ struct b43_led *led = container_of(led_dev, struct b43_led, led_dev);
+ struct b43_wl *wl = led->wl;
+
+ if (likely(!wl->leds.stop)) {
+ atomic_set(&led->state, brightness);
+ ieee80211_queue_work(wl->hw, &wl->leds.work);
+ }
}
static int b43_register_led(struct b43_wldev *dev, struct b43_led *led,
{
int err;
- b43_led_turn_off(dev, led_index, activelow);
- if (led->dev)
+ if (led->wl)
return -EEXIST;
if (!default_trigger)
return -EINVAL;
- led->dev = dev;
+ led->wl = dev->wl;
led->index = led_index;
led->activelow = activelow;
strncpy(led->name, name, sizeof(led->name));
+ atomic_set(&led->state, 0);
led->led_dev.name = led->name;
led->led_dev.default_trigger = default_trigger;
err = led_classdev_register(dev->dev->dev, &led->led_dev);
if (err) {
b43warn(dev->wl, "LEDs: Failed to register %s\n", name);
- led->dev = NULL;
+ led->wl = NULL;
return err;
}
+
return 0;
}
static void b43_unregister_led(struct b43_led *led)
{
- if (!led->dev)
+ if (!led->wl)
return;
led_classdev_unregister(&led->led_dev);
- b43_led_turn_off(led->dev, led->index, led->activelow);
- led->dev = NULL;
+ led->wl = NULL;
}
static void b43_map_led(struct b43_wldev *dev,
* generic LED triggers. */
switch (behaviour) {
case B43_LED_INACTIVE:
- break;
case B43_LED_OFF:
- b43_led_turn_off(dev, led_index, activelow);
- break;
case B43_LED_ON:
- b43_led_turn_on(dev, led_index, activelow);
break;
case B43_LED_ACTIVITY:
case B43_LED_TRANSFER:
case B43_LED_APTRANSFER:
snprintf(name, sizeof(name),
"b43-%s::tx", wiphy_name(hw->wiphy));
- b43_register_led(dev, &dev->led_tx, name,
+ b43_register_led(dev, &dev->wl->leds.led_tx, name,
ieee80211_get_tx_led_name(hw),
led_index, activelow);
snprintf(name, sizeof(name),
"b43-%s::rx", wiphy_name(hw->wiphy));
- b43_register_led(dev, &dev->led_rx, name,
+ b43_register_led(dev, &dev->wl->leds.led_rx, name,
ieee80211_get_rx_led_name(hw),
led_index, activelow);
break;
case B43_LED_MODE_BG:
snprintf(name, sizeof(name),
"b43-%s::radio", wiphy_name(hw->wiphy));
- b43_register_led(dev, &dev->led_radio, name,
+ b43_register_led(dev, &dev->wl->leds.led_radio, name,
ieee80211_get_radio_led_name(hw),
led_index, activelow);
- /* Sync the RF-kill LED state with radio and switch states. */
- if (dev->phy.radio_on && b43_is_hw_radio_enabled(dev))
- b43_led_turn_on(dev, led_index, activelow);
break;
case B43_LED_WEIRD:
case B43_LED_ASSOC:
snprintf(name, sizeof(name),
"b43-%s::assoc", wiphy_name(hw->wiphy));
- b43_register_led(dev, &dev->led_assoc, name,
+ b43_register_led(dev, &dev->wl->leds.led_assoc, name,
ieee80211_get_assoc_led_name(hw),
led_index, activelow);
break;
}
}
-void b43_leds_init(struct b43_wldev *dev)
+static void b43_led_get_sprominfo(struct b43_wldev *dev,
+ unsigned int led_index,
+ enum b43_led_behaviour *behaviour,
+ bool *activelow)
{
struct ssb_bus *bus = dev->dev->bus;
u8 sprom[4];
- int i;
- enum b43_led_behaviour behaviour;
- bool activelow;
sprom[0] = bus->sprom.gpio0;
sprom[1] = bus->sprom.gpio1;
sprom[2] = bus->sprom.gpio2;
sprom[3] = bus->sprom.gpio3;
- for (i = 0; i < 4; i++) {
- if (sprom[i] == 0xFF) {
- /* There is no LED information in the SPROM
- * for this LED. Hardcode it here. */
- activelow = 0;
- switch (i) {
- case 0:
- behaviour = B43_LED_ACTIVITY;
- activelow = 1;
- if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ)
- behaviour = B43_LED_RADIO_ALL;
- break;
- case 1:
- behaviour = B43_LED_RADIO_B;
- if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK)
- behaviour = B43_LED_ASSOC;
- break;
- case 2:
- behaviour = B43_LED_RADIO_A;
- break;
- case 3:
- behaviour = B43_LED_OFF;
- break;
- default:
- B43_WARN_ON(1);
- return;
- }
+ if (sprom[led_index] == 0xFF) {
+ /* There is no LED information in the SPROM
+ * for this LED. Hardcode it here. */
+ *activelow = 0;
+ switch (led_index) {
+ case 0:
+ *behaviour = B43_LED_ACTIVITY;
+ *activelow = 1;
+ if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ)
+ *behaviour = B43_LED_RADIO_ALL;
+ break;
+ case 1:
+ *behaviour = B43_LED_RADIO_B;
+ if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK)
+ *behaviour = B43_LED_ASSOC;
+ break;
+ case 2:
+ *behaviour = B43_LED_RADIO_A;
+ break;
+ case 3:
+ *behaviour = B43_LED_OFF;
+ break;
+ default:
+ B43_WARN_ON(1);
+ return;
+ }
+ } else {
+ *behaviour = sprom[led_index] & B43_LED_BEHAVIOUR;
+ *activelow = !!(sprom[led_index] & B43_LED_ACTIVELOW);
+ }
+}
+
+void b43_leds_init(struct b43_wldev *dev)
+{
+ struct b43_led *led;
+ unsigned int i;
+ enum b43_led_behaviour behaviour;
+ bool activelow;
+
+ /* Sync the RF-kill LED state (if we have one) with radio and switch states. */
+ led = &dev->wl->leds.led_radio;
+ if (led->wl) {
+ if (dev->phy.radio_on && b43_is_hw_radio_enabled(dev)) {
+ b43_led_turn_on(dev, led->index, led->activelow);
+ led->hw_state = 1;
+ atomic_set(&led->state, 1);
} else {
- behaviour = sprom[i] & B43_LED_BEHAVIOUR;
- activelow = !!(sprom[i] & B43_LED_ACTIVELOW);
+ b43_led_turn_off(dev, led->index, led->activelow);
+ led->hw_state = 0;
+ atomic_set(&led->state, 0);
}
- b43_map_led(dev, i, behaviour, activelow);
}
+
+ /* Initialize TX/RX/ASSOC leds */
+ led = &dev->wl->leds.led_tx;
+ if (led->wl) {
+ b43_led_turn_off(dev, led->index, led->activelow);
+ led->hw_state = 0;
+ atomic_set(&led->state, 0);
+ }
+ led = &dev->wl->leds.led_rx;
+ if (led->wl) {
+ b43_led_turn_off(dev, led->index, led->activelow);
+ led->hw_state = 0;
+ atomic_set(&led->state, 0);
+ }
+ led = &dev->wl->leds.led_assoc;
+ if (led->wl) {
+ b43_led_turn_off(dev, led->index, led->activelow);
+ led->hw_state = 0;
+ atomic_set(&led->state, 0);
+ }
+
+ /* Initialize other LED states. */
+ for (i = 0; i < B43_MAX_NR_LEDS; i++) {
+ b43_led_get_sprominfo(dev, i, &behaviour, &activelow);
+ switch (behaviour) {
+ case B43_LED_OFF:
+ b43_led_turn_off(dev, i, activelow);
+ break;
+ case B43_LED_ON:
+ b43_led_turn_on(dev, i, activelow);
+ break;
+ default:
+ /* Leave others as-is. */
+ break;
+ }
+ }
+
+ dev->wl->leds.stop = 0;
}
void b43_leds_exit(struct b43_wldev *dev)
{
- b43_unregister_led(&dev->led_tx);
- b43_unregister_led(&dev->led_rx);
- b43_unregister_led(&dev->led_assoc);
- b43_unregister_led(&dev->led_radio);
+ struct b43_leds *leds = &dev->wl->leds;
+
+ b43_led_turn_off(dev, leds->led_tx.index, leds->led_tx.activelow);
+ b43_led_turn_off(dev, leds->led_rx.index, leds->led_rx.activelow);
+ b43_led_turn_off(dev, leds->led_assoc.index, leds->led_assoc.activelow);
+ b43_led_turn_off(dev, leds->led_radio.index, leds->led_radio.activelow);
+}
+
+void b43_leds_stop(struct b43_wldev *dev)
+{
+ struct b43_leds *leds = &dev->wl->leds;
+
+ leds->stop = 1;
+ cancel_work_sync(&leds->work);
+}
+
+void b43_leds_register(struct b43_wldev *dev)
+{
+ unsigned int i;
+ enum b43_led_behaviour behaviour;
+ bool activelow;
+
+ INIT_WORK(&dev->wl->leds.work, b43_leds_work);
+
+ /* Register the LEDs to the LED subsystem. */
+ for (i = 0; i < B43_MAX_NR_LEDS; i++) {
+ b43_led_get_sprominfo(dev, i, &behaviour, &activelow);
+ b43_map_led(dev, i, behaviour, activelow);
+ }
+}
+
+void b43_leds_unregister(struct b43_wldev *dev)
+{
+ struct b43_leds *leds = &dev->wl->leds;
+
+ b43_unregister_led(&leds->led_tx);
+ b43_unregister_led(&leds->led_rx);
+ b43_unregister_led(&leds->led_assoc);
+ b43_unregister_led(&leds->led_radio);
}
#include <linux/types.h>
#include <linux/leds.h>
+#include <linux/workqueue.h>
#define B43_LED_MAX_NAME_LEN 31
struct b43_led {
- struct b43_wldev *dev;
+ struct b43_wl *wl;
/* The LED class device */
struct led_classdev led_dev;
/* The index number of the LED. */
bool activelow;
/* The unique name string for this LED device. */
char name[B43_LED_MAX_NAME_LEN + 1];
+ /* The current status of the LED. This is updated locklessly. */
+ atomic_t state;
+ /* The active state in hardware. */
+ bool hw_state;
};
+struct b43_leds {
+ struct b43_led led_tx;
+ struct b43_led led_rx;
+ struct b43_led led_radio;
+ struct b43_led led_assoc;
+
+ bool stop;
+ struct work_struct work;
+};
+
+#define B43_MAX_NR_LEDS 4
+
#define B43_LED_BEHAVIOUR 0x7F
#define B43_LED_ACTIVELOW 0x80
/* LED behaviour values */
B43_LED_INACTIVE,
};
+void b43_leds_register(struct b43_wldev *dev);
+void b43_leds_unregister(struct b43_wldev *dev);
void b43_leds_init(struct b43_wldev *dev);
void b43_leds_exit(struct b43_wldev *dev);
+void b43_leds_stop(struct b43_wldev *dev);
#else /* CONFIG_B43_LEDS */
/* LED support disabled */
-struct b43_led {
+struct b43_leds {
/* empty */
};
+static inline void b43_leds_register(struct b43_wldev *dev)
+{
+}
+static inline void b43_leds_unregister(struct b43_wldev *dev)
+{
+}
static inline void b43_leds_init(struct b43_wldev *dev)
{
}
static inline void b43_leds_exit(struct b43_wldev *dev)
{
}
+static inline void b43_leds_stop(struct b43_wldev *dev)
+{
+}
#endif /* CONFIG_B43_LEDS */
#endif /* B43_LEDS_H_ */
Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org>
Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch>
+ SDIO support
+ Copyright (c) 2009 Albert Herranz <albert_herranz@yahoo.es>
+
Some parts of the code in this file are derived from the ipw2200
driver Copyright(c) 2003 - 2004 Intel Corporation.
#include "xmit.h"
#include "lo.h"
#include "pcmcia.h"
+#include "sdio.h"
+#include <linux/mmc/sdio_func.h>
MODULE_DESCRIPTION("Broadcom B43 wireless driver");
MODULE_AUTHOR("Martin Langer");
mutex_lock(&wl->mutex);
dev = wl->current_dev;
if (likely(dev && (b43_status(dev) >= B43_STAT_INITIALIZED))) {
- if (0 /*FIXME dev->dev->bus->bustype == SSB_BUSTYPE_SDIO*/) {
+ if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
/* wl->mutex is enough. */
b43_do_beacon_update_trigger_work(dev);
mmiowb();
/* Re-enable interrupts on the device by restoring the current interrupt mask. */
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask);
+
+#if B43_DEBUG
+ if (b43_debug(dev, B43_DBG_VERBOSESTATS)) {
+ dev->irq_count++;
+ for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) {
+ if (reason & (1 << i))
+ dev->irq_bit_count[i]++;
+ }
+ }
+#endif
}
/* Interrupt thread handler. Handles device interrupts in thread context. */
return ret;
}
+/* SDIO interrupt handler. This runs in process context. */
+static void b43_sdio_interrupt_handler(struct b43_wldev *dev)
+{
+ struct b43_wl *wl = dev->wl;
+ irqreturn_t ret;
+
+ mutex_lock(&wl->mutex);
+
+ ret = b43_do_interrupt(dev);
+ if (ret == IRQ_WAKE_THREAD)
+ b43_do_interrupt_thread(dev);
+
+ mutex_unlock(&wl->mutex);
+}
+
void b43_do_release_fw(struct b43_firmware_file *fw)
{
release_firmware(fw->data);
cfp_pretbtt = 50;
}
b43_write16(dev, 0x612, cfp_pretbtt);
+
+ /* FIXME: We don't currently implement the PMQ mechanism,
+ * so always disable it. If we want to implement PMQ,
+ * we need to enable it here (clear DISCPMQ) in AP mode.
+ */
+ if (0 /* ctl & B43_MACCTL_AP */) {
+ b43_write32(dev, B43_MMIO_MACCTL,
+ b43_read32(dev, B43_MMIO_MACCTL)
+ & ~B43_MACCTL_DISCPMQ);
+ } else {
+ b43_write32(dev, B43_MMIO_MACCTL,
+ b43_read32(dev, B43_MMIO_MACCTL)
+ | B43_MACCTL_DISCPMQ);
+ }
}
static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm)
atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT);
wmb();
+
+#if B43_DEBUG
+ if (b43_debug(dev, B43_DBG_VERBOSESTATS)) {
+ unsigned int i;
+
+ b43dbg(dev->wl, "Stats: %7u IRQs/sec, %7u TX/sec, %7u RX/sec\n",
+ dev->irq_count / 15,
+ dev->tx_count / 15,
+ dev->rx_count / 15);
+ dev->irq_count = 0;
+ dev->tx_count = 0;
+ dev->rx_count = 0;
+ for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) {
+ if (dev->irq_bit_count[i]) {
+ b43dbg(dev->wl, "Stats: %7u IRQ-%02u/sec (0x%08X)\n",
+ dev->irq_bit_count[i] / 15, i, (1 << i));
+ dev->irq_bit_count[i] = 0;
+ }
+ }
+ }
+#endif
}
static void do_periodic_work(struct b43_wldev *dev)
static int b43_rng_read(struct hwrng *rng, u32 *data)
{
struct b43_wl *wl = (struct b43_wl *)rng->priv;
+ struct b43_wldev *dev;
+ int count = -ENODEV;
- /* FIXME: We need to take wl->mutex here to make sure the device
- * is not going away from under our ass. However it could deadlock
- * with hwrng internal locking. */
-
- *data = b43_read16(wl->current_dev, B43_MMIO_RNG);
+ mutex_lock(&wl->mutex);
+ dev = wl->current_dev;
+ if (likely(dev && b43_status(dev) >= B43_STAT_INITIALIZED)) {
+ *data = b43_read16(dev, B43_MMIO_RNG);
+ count = sizeof(u16);
+ }
+ mutex_unlock(&wl->mutex);
- return (sizeof(u16));
+ return count;
}
#endif /* CONFIG_B43_HWRNG */
dev_kfree_skb(skb); /* Drop it */
}
+#if B43_DEBUG
+ dev->tx_count++;
+#endif
mutex_unlock(&wl->mutex);
}
/* Disable interrupts on the device. */
b43_set_status(dev, B43_STAT_INITIALIZED);
- if (0 /*FIXME dev->dev->bus->bustype == SSB_BUSTYPE_SDIO*/) {
+ if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
/* wl->mutex is locked. That is enough. */
b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0);
b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */
b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */
spin_unlock_irq(&wl->hardirq_lock);
}
- /* Synchronize the interrupt handlers. Unlock to avoid deadlocks. */
+ /* Synchronize and free the interrupt handlers. Unlock to avoid deadlocks. */
orig_dev = dev;
mutex_unlock(&wl->mutex);
- synchronize_irq(dev->dev->irq);
+ if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
+ b43_sdio_free_irq(dev);
+ } else {
+ synchronize_irq(dev->dev->irq);
+ free_irq(dev->dev->irq, dev);
+ }
mutex_lock(&wl->mutex);
dev = wl->current_dev;
if (!dev)
dev_kfree_skb(skb_dequeue(&wl->tx_queue));
b43_mac_suspend(dev);
- free_irq(dev->dev->irq, dev);
+ b43_leds_exit(dev);
b43dbg(wl, "Wireless interface stopped\n");
return dev;
B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED);
drain_txstatus_queue(dev);
- err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler,
- b43_interrupt_thread_handler,
- IRQF_SHARED, KBUILD_MODNAME, dev);
- if (err) {
- b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq);
- goto out;
+ if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) {
+ err = b43_sdio_request_irq(dev, b43_sdio_interrupt_handler);
+ if (err) {
+ b43err(dev->wl, "Cannot request SDIO IRQ\n");
+ goto out;
+ }
+ } else {
+ err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler,
+ b43_interrupt_thread_handler,
+ IRQF_SHARED, KBUILD_MODNAME, dev);
+ if (err) {
+ b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq);
+ goto out;
+ }
}
/* We are ready to run. */
/* Start maintainance work */
b43_periodic_tasks_setup(dev);
+ b43_leds_init(dev);
+
b43dbg(dev->wl, "Wireless interface started\n");
- out:
+out:
return err;
}
macctl |= B43_MACCTL_PSM_JMP0;
b43_write32(dev, B43_MMIO_MACCTL, macctl);
- if (!dev->suspend_in_progress) {
- b43_leds_exit(dev);
- b43_rng_exit(dev->wl);
- }
b43_dma_free(dev);
b43_pio_free(dev);
b43_chip_exit(dev);
/* Initialize a wireless core */
static int b43_wireless_core_init(struct b43_wldev *dev)
{
- struct b43_wl *wl = dev->wl;
struct ssb_bus *bus = dev->dev->bus;
struct ssb_sprom *sprom = &bus->sprom;
struct b43_phy *phy = &dev->phy;
/* Maximum Contention Window */
b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF);
- if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) || B43_FORCE_PIO) {
+ if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) ||
+ (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) ||
+ B43_FORCE_PIO) {
dev->__using_pio_transfers = 1;
err = b43_pio_init(dev);
} else {
ssb_bus_powerup(bus, !(sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW));
b43_upload_card_macaddress(dev);
b43_security_init(dev);
- if (!dev->suspend_in_progress)
- b43_rng_init(wl);
+
+ ieee80211_wake_queues(dev->wl->hw);
ieee80211_wake_queues(dev->wl->hw);
b43_set_status(dev, B43_STAT_INITIALIZED);
- if (!dev->suspend_in_progress)
- b43_leds_init(dev);
out:
return err;
/* Initialize struct b43_wl */
wl->hw = hw;
- spin_lock_init(&wl->leds_lock);
mutex_init(&wl->mutex);
spin_lock_init(&wl->hardirq_lock);
INIT_LIST_HEAD(&wl->devlist);
err = ieee80211_register_hw(wl->hw);
if (err)
goto err_one_core_detach;
+ b43_leds_register(wl->current_dev);
+ b43_rng_init(wl);
}
out:
* might have modified it. Restoring is important, so the networking
* stack can properly free resources. */
wl->hw->queues = wl->mac80211_initially_registered_queues;
+ b43_leds_stop(wldev);
ieee80211_unregister_hw(wl->hw);
}
b43_one_core_detach(dev);
if (list_empty(&wl->devlist)) {
+ b43_rng_exit(wl);
+ b43_leds_unregister(wldev);
/* Last core on the chip unregistered.
* We can destroy common struct b43_wl.
*/
ieee80211_queue_work(dev->wl->hw, &dev->restart_work);
}
-#ifdef CONFIG_PM
-
-static int b43_suspend(struct ssb_device *dev, pm_message_t state)
-{
- struct b43_wldev *wldev = ssb_get_drvdata(dev);
- struct b43_wl *wl = wldev->wl;
-
- b43dbg(wl, "Suspending...\n");
-
- mutex_lock(&wl->mutex);
- wldev->suspend_in_progress = true;
- wldev->suspend_init_status = b43_status(wldev);
- if (wldev->suspend_init_status >= B43_STAT_STARTED)
- wldev = b43_wireless_core_stop(wldev);
- if (wldev && wldev->suspend_init_status >= B43_STAT_INITIALIZED)
- b43_wireless_core_exit(wldev);
- mutex_unlock(&wl->mutex);
-
- b43dbg(wl, "Device suspended.\n");
-
- return 0;
-}
-
-static int b43_resume(struct ssb_device *dev)
-{
- struct b43_wldev *wldev = ssb_get_drvdata(dev);
- struct b43_wl *wl = wldev->wl;
- int err = 0;
-
- b43dbg(wl, "Resuming...\n");
-
- mutex_lock(&wl->mutex);
- if (wldev->suspend_init_status >= B43_STAT_INITIALIZED) {
- err = b43_wireless_core_init(wldev);
- if (err) {
- b43err(wl, "Resume failed at core init\n");
- goto out;
- }
- }
- if (wldev->suspend_init_status >= B43_STAT_STARTED) {
- err = b43_wireless_core_start(wldev);
- if (err) {
- b43_leds_exit(wldev);
- b43_rng_exit(wldev->wl);
- b43_wireless_core_exit(wldev);
- b43err(wl, "Resume failed at core start\n");
- goto out;
- }
- }
- b43dbg(wl, "Device resumed.\n");
- out:
- wldev->suspend_in_progress = false;
- mutex_unlock(&wl->mutex);
- return err;
-}
-
-#else /* CONFIG_PM */
-# define b43_suspend NULL
-# define b43_resume NULL
-#endif /* CONFIG_PM */
-
static struct ssb_driver b43_ssb_driver = {
.name = KBUILD_MODNAME,
.id_table = b43_ssb_tbl,
.probe = b43_probe,
.remove = b43_remove,
- .suspend = b43_suspend,
- .resume = b43_resume,
};
static void b43_print_driverinfo(void)
{
const char *feat_pci = "", *feat_pcmcia = "", *feat_nphy = "",
- *feat_leds = "";
+ *feat_leds = "", *feat_sdio = "";
#ifdef CONFIG_B43_PCI_AUTOSELECT
feat_pci = "P";
#endif
#ifdef CONFIG_B43_LEDS
feat_leds = "L";
+#endif
+#ifdef CONFIG_B43_SDIO
+ feat_sdio = "S";
#endif
printk(KERN_INFO "Broadcom 43xx driver loaded "
- "[ Features: %s%s%s%s, Firmware-ID: "
+ "[ Features: %s%s%s%s%s, Firmware-ID: "
B43_SUPPORTED_FIRMWARE_ID " ]\n",
feat_pci, feat_pcmcia, feat_nphy,
- feat_leds);
+ feat_leds, feat_sdio);
}
static int __init b43_init(void)
err = b43_pcmcia_init();
if (err)
goto err_dfs_exit;
- err = ssb_driver_register(&b43_ssb_driver);
+ err = b43_sdio_init();
if (err)
goto err_pcmcia_exit;
+ err = ssb_driver_register(&b43_ssb_driver);
+ if (err)
+ goto err_sdio_exit;
b43_print_driverinfo();
return err;
+err_sdio_exit:
+ b43_sdio_exit();
err_pcmcia_exit:
b43_pcmcia_exit();
err_dfs_exit:
static void __exit b43_exit(void)
{
ssb_driver_unregister(&b43_ssb_driver);
+ b43_sdio_exit();
b43_pcmcia_exit();
b43_debugfs_exit();
}
return B43_TXPWR_RES_DONE;
}
+void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on)
+{
+ if (on) {
+ b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xfff8);
+ } else {
+ b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0x0007);
+ b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x0007);
+ }
+}
+
const struct b43_phy_operations b43_phyops_lp = {
.allocate = b43_lpphy_op_allocate,
.free = b43_lpphy_op_free,
.radio_read = b43_lpphy_op_radio_read,
.radio_write = b43_lpphy_op_radio_write,
.software_rfkill = b43_lpphy_op_software_rfkill,
- .switch_analog = b43_phyop_switch_analog_generic,
+ .switch_analog = b43_lpphy_op_switch_analog,
.switch_channel = b43_lpphy_op_switch_channel,
.get_default_chan = b43_lpphy_op_get_default_chan,
.set_rx_antenna = b43_lpphy_op_set_rx_antenna,
q->mmio_base + B43_PIO_TXDATA,
sizeof(u16));
if (data_len & 1) {
+ u8 tail[2] = { 0, };
+
/* Write the last byte. */
ctl &= ~B43_PIO_TXCTL_WRITEHI;
b43_piotx_write16(q, B43_PIO_TXCTL, ctl);
- b43_piotx_write16(q, B43_PIO_TXDATA, data[data_len - 1]);
+ tail[0] = data[data_len - 1];
+ ssb_block_write(dev->dev, tail, 2,
+ q->mmio_base + B43_PIO_TXDATA,
+ sizeof(u16));
}
return ctl;
q->mmio_base + B43_PIO8_TXDATA,
sizeof(u32));
if (data_len & 3) {
- u32 value = 0;
+ u8 tail[4] = { 0, };
/* Write the last few bytes. */
ctl &= ~(B43_PIO8_TXCTL_8_15 | B43_PIO8_TXCTL_16_23 |
B43_PIO8_TXCTL_24_31);
- data = &(data[data_len - 1]);
switch (data_len & 3) {
case 3:
- ctl |= B43_PIO8_TXCTL_16_23;
- value |= (u32)(*data) << 16;
- data--;
+ ctl |= B43_PIO8_TXCTL_16_23 | B43_PIO8_TXCTL_8_15;
+ tail[0] = data[data_len - 3];
+ tail[1] = data[data_len - 2];
+ tail[2] = data[data_len - 1];
+ break;
case 2:
ctl |= B43_PIO8_TXCTL_8_15;
- value |= (u32)(*data) << 8;
- data--;
+ tail[0] = data[data_len - 2];
+ tail[1] = data[data_len - 1];
+ break;
case 1:
- value |= (u32)(*data);
+ tail[0] = data[data_len - 1];
+ break;
}
b43_piotx_write32(q, B43_PIO8_TXCTL, ctl);
- b43_piotx_write32(q, B43_PIO8_TXDATA, value);
+ ssb_block_write(dev->dev, tail, 4,
+ q->mmio_base + B43_PIO8_TXDATA,
+ sizeof(u32));
}
return ctl;
q->buffer_used -= total_len;
q->free_packet_slots += 1;
- ieee80211_tx_status_irqsafe(dev->wl->hw, pack->skb);
+ ieee80211_tx_status(dev->wl->hw, pack->skb);
pack->skb = NULL;
list_add(&pack->list, &q->packets_list);
q->mmio_base + B43_PIO8_RXDATA,
sizeof(u32));
if (len & 3) {
- u32 value;
- char *data;
+ u8 tail[4] = { 0, };
/* Read the last few bytes. */
- value = b43_piorx_read32(q, B43_PIO8_RXDATA);
- data = &(skb->data[len + padding - 1]);
+ ssb_block_read(dev->dev, tail, 4,
+ q->mmio_base + B43_PIO8_RXDATA,
+ sizeof(u32));
switch (len & 3) {
case 3:
- *data = (value >> 16);
- data--;
+ skb->data[len + padding - 3] = tail[0];
+ skb->data[len + padding - 2] = tail[1];
+ skb->data[len + padding - 1] = tail[2];
+ break;
case 2:
- *data = (value >> 8);
- data--;
+ skb->data[len + padding - 2] = tail[0];
+ skb->data[len + padding - 1] = tail[1];
+ break;
case 1:
- *data = value;
+ skb->data[len + padding - 1] = tail[0];
+ break;
}
}
} else {
q->mmio_base + B43_PIO_RXDATA,
sizeof(u16));
if (len & 1) {
- u16 value;
+ u8 tail[2] = { 0, };
/* Read the last byte. */
- value = b43_piorx_read16(q, B43_PIO_RXDATA);
- skb->data[len + padding - 1] = value;
+ ssb_block_read(dev->dev, tail, 2,
+ q->mmio_base + B43_PIO_RXDATA,
+ sizeof(u16));
+ skb->data[len + padding - 1] = tail[0];
}
}
/* Returns TRUE, if the radio is enabled in hardware. */
bool b43_is_hw_radio_enabled(struct b43_wldev *dev)
{
- if (dev->phy.rev >= 3) {
+ if (dev->phy.rev >= 3 || dev->phy.type == B43_PHYTYPE_LP) {
if (!(b43_read32(dev, B43_MMIO_RADIO_HWENABLED_HI)
& B43_MMIO_RADIO_HWENABLED_HI_MASK))
return 1;
--- /dev/null
+/*
+ * Broadcom B43 wireless driver
+ *
+ * SDIO over Sonics Silicon Backplane bus glue for b43.
+ *
+ * Copyright (C) 2009 Albert Herranz
+ * Copyright (C) 2009 Michael Buesch <mb@bu3sch.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/sdio_func.h>
+#include <linux/mmc/sdio_ids.h>
+#include <linux/ssb/ssb.h>
+
+#include "sdio.h"
+#include "b43.h"
+
+
+#define HNBU_CHIPID 0x01 /* vendor & device id */
+
+#define B43_SDIO_BLOCK_SIZE 64 /* rx fifo max size in bytes */
+
+
+static const struct b43_sdio_quirk {
+ u16 vendor;
+ u16 device;
+ unsigned int quirks;
+} b43_sdio_quirks[] = {
+ { 0x14E4, 0x4318, SSB_QUIRK_SDIO_READ_AFTER_WRITE32, },
+ { },
+};
+
+
+static unsigned int b43_sdio_get_quirks(u16 vendor, u16 device)
+{
+ const struct b43_sdio_quirk *q;
+
+ for (q = b43_sdio_quirks; q->quirks; q++) {
+ if (vendor == q->vendor && device == q->device)
+ return q->quirks;
+ }
+
+ return 0;
+}
+
+static void b43_sdio_interrupt_dispatcher(struct sdio_func *func)
+{
+ struct b43_sdio *sdio = sdio_get_drvdata(func);
+ struct b43_wldev *dev = sdio->irq_handler_opaque;
+
+ if (unlikely(b43_status(dev) < B43_STAT_STARTED))
+ return;
+
+ sdio_release_host(func);
+ sdio->irq_handler(dev);
+ sdio_claim_host(func);
+}
+
+int b43_sdio_request_irq(struct b43_wldev *dev,
+ void (*handler)(struct b43_wldev *dev))
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct sdio_func *func = bus->host_sdio;
+ struct b43_sdio *sdio = sdio_get_drvdata(func);
+ int err;
+
+ sdio->irq_handler_opaque = dev;
+ sdio->irq_handler = handler;
+ sdio_claim_host(func);
+ err = sdio_claim_irq(func, b43_sdio_interrupt_dispatcher);
+ sdio_release_host(func);
+
+ return err;
+}
+
+void b43_sdio_free_irq(struct b43_wldev *dev)
+{
+ struct ssb_bus *bus = dev->dev->bus;
+ struct sdio_func *func = bus->host_sdio;
+ struct b43_sdio *sdio = sdio_get_drvdata(func);
+
+ sdio_claim_host(func);
+ sdio_release_irq(func);
+ sdio_release_host(func);
+ sdio->irq_handler_opaque = NULL;
+ sdio->irq_handler = NULL;
+}
+
+static int b43_sdio_probe(struct sdio_func *func,
+ const struct sdio_device_id *id)
+{
+ struct b43_sdio *sdio;
+ struct sdio_func_tuple *tuple;
+ u16 vendor = 0, device = 0;
+ int error;
+
+ /* Look for the card chip identifier. */
+ tuple = func->tuples;
+ while (tuple) {
+ switch (tuple->code) {
+ case 0x80:
+ switch (tuple->data[0]) {
+ case HNBU_CHIPID:
+ if (tuple->size != 5)
+ break;
+ vendor = tuple->data[1] | (tuple->data[2]<<8);
+ device = tuple->data[3] | (tuple->data[4]<<8);
+ dev_info(&func->dev, "Chip ID %04x:%04x\n",
+ vendor, device);
+ break;
+ default:
+ break;
+ }
+ break;
+ default:
+ break;
+ }
+ tuple = tuple->next;
+ }
+ if (!vendor || !device) {
+ error = -ENODEV;
+ goto out;
+ }
+
+ sdio_claim_host(func);
+ error = sdio_set_block_size(func, B43_SDIO_BLOCK_SIZE);
+ if (error) {
+ dev_err(&func->dev, "failed to set block size to %u bytes,"
+ " error %d\n", B43_SDIO_BLOCK_SIZE, error);
+ goto err_release_host;
+ }
+ error = sdio_enable_func(func);
+ if (error) {
+ dev_err(&func->dev, "failed to enable func, error %d\n", error);
+ goto err_release_host;
+ }
+ sdio_release_host(func);
+
+ sdio = kzalloc(sizeof(*sdio), GFP_KERNEL);
+ if (!sdio) {
+ error = -ENOMEM;
+ dev_err(&func->dev, "failed to allocate ssb bus\n");
+ goto err_disable_func;
+ }
+ error = ssb_bus_sdiobus_register(&sdio->ssb, func,
+ b43_sdio_get_quirks(vendor, device));
+ if (error) {
+ dev_err(&func->dev, "failed to register ssb sdio bus,"
+ " error %d\n", error);
+ goto err_free_ssb;
+ }
+ sdio_set_drvdata(func, sdio);
+
+ return 0;
+
+err_free_ssb:
+ kfree(sdio);
+err_disable_func:
+ sdio_disable_func(func);
+err_release_host:
+ sdio_release_host(func);
+out:
+ return error;
+}
+
+static void b43_sdio_remove(struct sdio_func *func)
+{
+ struct b43_sdio *sdio = sdio_get_drvdata(func);
+
+ ssb_bus_unregister(&sdio->ssb);
+ sdio_disable_func(func);
+ kfree(sdio);
+ sdio_set_drvdata(func, NULL);
+}
+
+static const struct sdio_device_id b43_sdio_ids[] = {
+ { SDIO_DEVICE(0x02d0, 0x044b) }, /* Nintendo Wii WLAN daughter card */
+ { },
+};
+
+static struct sdio_driver b43_sdio_driver = {
+ .name = "b43-sdio",
+ .id_table = b43_sdio_ids,
+ .probe = b43_sdio_probe,
+ .remove = b43_sdio_remove,
+};
+
+int b43_sdio_init(void)
+{
+ return sdio_register_driver(&b43_sdio_driver);
+}
+
+void b43_sdio_exit(void)
+{
+ sdio_unregister_driver(&b43_sdio_driver);
+}
--- /dev/null
+#ifndef B43_SDIO_H_
+#define B43_SDIO_H_
+
+#include <linux/ssb/ssb.h>
+
+struct b43_wldev;
+
+
+#ifdef CONFIG_B43_SDIO
+
+struct b43_sdio {
+ struct ssb_bus ssb;
+ void *irq_handler_opaque;
+ void (*irq_handler)(struct b43_wldev *dev);
+};
+
+int b43_sdio_request_irq(struct b43_wldev *dev,
+ void (*handler)(struct b43_wldev *dev));
+void b43_sdio_free_irq(struct b43_wldev *dev);
+
+int b43_sdio_init(void);
+void b43_sdio_exit(void);
+
+
+#else /* CONFIG_B43_SDIO */
+
+
+int b43_sdio_request_irq(struct b43_wldev *dev,
+ void (*handler)(struct b43_wldev *dev))
+{
+ return -ENODEV;
+}
+void b43_sdio_free_irq(struct b43_wldev *dev)
+{
+}
+static inline int b43_sdio_init(void)
+{
+ return 0;
+}
+static inline void b43_sdio_exit(void)
+{
+}
+
+#endif /* CONFIG_B43_SDIO */
+#endif /* B43_SDIO_H_ */
}
memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status));
- ieee80211_rx_irqsafe(dev->wl->hw, skb);
+ ieee80211_rx(dev->wl->hw, skb);
+#if B43_DEBUG
+ dev->rx_count++;
+#endif
return;
drop:
b43dbg(dev->wl, "RX: Packet dropped\n");
.setup_deferred_work = iwl5000_setup_deferred_work,
.is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr,
.load_ucode = iwl5000_load_ucode,
+ .dump_nic_event_log = iwl_dump_nic_event_log,
+ .dump_nic_error_log = iwl_dump_nic_error_log,
.init_alive_start = iwl5000_init_alive_start,
.alive_notify = iwl5000_alive_notify,
.send_tx_power = iwl5000_send_tx_power,
.txq_free_tfd = iwl3945_hw_txq_free_tfd,
.txq_init = iwl3945_hw_tx_queue_init,
.load_ucode = iwl3945_load_bsm,
+ .dump_nic_event_log = iwl3945_dump_nic_event_log,
+ .dump_nic_error_log = iwl3945_dump_nic_error_log,
.apm_ops = {
.init = iwl3945_apm_init,
.reset = iwl3945_apm_reset,
struct iwl_host_cmd *cmd);
extern unsigned int iwl3945_fill_beacon_frame(struct iwl_priv *priv,
struct ieee80211_hdr *hdr,int left);
+extern void iwl3945_dump_nic_event_log(struct iwl_priv *priv);
+extern void iwl3945_dump_nic_error_log(struct iwl_priv *priv);
/*
* Currently used by iwl-3945-rs... look at restructuring so that it doesn't
agg->frame_count, txq_id, idx);
hdr = iwl_tx_queue_get_hdr(priv, txq_id, idx);
+ if (!hdr) {
+ IWL_ERR(priv,
+ "BUG_ON idx doesn't point to valid skb"
+ " idx=%d, txq_id=%d\n", idx, txq_id);
+ return -1;
+ }
sc = le16_to_cpu(hdr->seq_ctrl);
if (idx != (SEQ_TO_SN(sc) & 0xff)) {
.alive_notify = iwl4965_alive_notify,
.init_alive_start = iwl4965_init_alive_start,
.load_ucode = iwl4965_load_bsm,
+ .dump_nic_event_log = iwl_dump_nic_event_log,
+ .dump_nic_error_log = iwl_dump_nic_error_log,
.apm_ops = {
.init = iwl4965_apm_init,
.reset = iwl4965_apm_reset,
agg->frame_count, txq_id, idx);
hdr = iwl_tx_queue_get_hdr(priv, txq_id, idx);
+ if (!hdr) {
+ IWL_ERR(priv,
+ "BUG_ON idx doesn't point to valid skb"
+ " idx=%d, txq_id=%d\n", idx, txq_id);
+ return -1;
+ }
sc = le16_to_cpu(hdr->seq_ctrl);
if (idx != (SEQ_TO_SN(sc) & 0xff)) {
.rx_handler_setup = iwl5000_rx_handler_setup,
.setup_deferred_work = iwl5000_setup_deferred_work,
.is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr,
+ .dump_nic_event_log = iwl_dump_nic_event_log,
+ .dump_nic_error_log = iwl_dump_nic_error_log,
.load_ucode = iwl5000_load_ucode,
.init_alive_start = iwl5000_init_alive_start,
.alive_notify = iwl5000_alive_notify,
.rx_handler_setup = iwl5000_rx_handler_setup,
.setup_deferred_work = iwl5000_setup_deferred_work,
.is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr,
+ .dump_nic_event_log = iwl_dump_nic_event_log,
+ .dump_nic_error_log = iwl_dump_nic_error_log,
.load_ucode = iwl5000_load_ucode,
.init_alive_start = iwl5000_init_alive_start,
.alive_notify = iwl5000_alive_notify,
.setup_deferred_work = iwl5000_setup_deferred_work,
.is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr,
.load_ucode = iwl5000_load_ucode,
+ .dump_nic_event_log = iwl_dump_nic_event_log,
+ .dump_nic_error_log = iwl_dump_nic_error_log,
.init_alive_start = iwl5000_init_alive_start,
.alive_notify = iwl5000_alive_notify,
.send_tx_power = iwl5000_send_tx_power,
return ret;
}
+#ifdef CONFIG_IWLWIFI_DEBUG
+static const char *desc_lookup_text[] = {
+ "OK",
+ "FAIL",
+ "BAD_PARAM",
+ "BAD_CHECKSUM",
+ "NMI_INTERRUPT_WDG",
+ "SYSASSERT",
+ "FATAL_ERROR",
+ "BAD_COMMAND",
+ "HW_ERROR_TUNE_LOCK",
+ "HW_ERROR_TEMPERATURE",
+ "ILLEGAL_CHAN_FREQ",
+ "VCC_NOT_STABLE",
+ "FH_ERROR",
+ "NMI_INTERRUPT_HOST",
+ "NMI_INTERRUPT_ACTION_PT",
+ "NMI_INTERRUPT_UNKNOWN",
+ "UCODE_VERSION_MISMATCH",
+ "HW_ERROR_ABS_LOCK",
+ "HW_ERROR_CAL_LOCK_FAIL",
+ "NMI_INTERRUPT_INST_ACTION_PT",
+ "NMI_INTERRUPT_DATA_ACTION_PT",
+ "NMI_TRM_HW_ER",
+ "NMI_INTERRUPT_TRM",
+ "NMI_INTERRUPT_BREAK_POINT"
+ "DEBUG_0",
+ "DEBUG_1",
+ "DEBUG_2",
+ "DEBUG_3",
+ "UNKNOWN"
+};
+
+static const char *desc_lookup(int i)
+{
+ int max = ARRAY_SIZE(desc_lookup_text) - 1;
+
+ if (i < 0 || i > max)
+ i = max;
+
+ return desc_lookup_text[i];
+}
+
+#define ERROR_START_OFFSET (1 * sizeof(u32))
+#define ERROR_ELEM_SIZE (7 * sizeof(u32))
+
+void iwl_dump_nic_error_log(struct iwl_priv *priv)
+{
+ u32 data2, line;
+ u32 desc, time, count, base, data1;
+ u32 blink1, blink2, ilink1, ilink2;
+
+ if (priv->ucode_type == UCODE_INIT)
+ base = le32_to_cpu(priv->card_alive_init.error_event_table_ptr);
+ else
+ base = le32_to_cpu(priv->card_alive.error_event_table_ptr);
+
+ if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) {
+ IWL_ERR(priv, "Not valid error log pointer 0x%08X\n", base);
+ return;
+ }
+
+ count = iwl_read_targ_mem(priv, base);
+
+ if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) {
+ IWL_ERR(priv, "Start IWL Error Log Dump:\n");
+ IWL_ERR(priv, "Status: 0x%08lX, count: %d\n",
+ priv->status, count);
+ }
+
+ desc = iwl_read_targ_mem(priv, base + 1 * sizeof(u32));
+ blink1 = iwl_read_targ_mem(priv, base + 3 * sizeof(u32));
+ blink2 = iwl_read_targ_mem(priv, base + 4 * sizeof(u32));
+ ilink1 = iwl_read_targ_mem(priv, base + 5 * sizeof(u32));
+ ilink2 = iwl_read_targ_mem(priv, base + 6 * sizeof(u32));
+ data1 = iwl_read_targ_mem(priv, base + 7 * sizeof(u32));
+ data2 = iwl_read_targ_mem(priv, base + 8 * sizeof(u32));
+ line = iwl_read_targ_mem(priv, base + 9 * sizeof(u32));
+ time = iwl_read_targ_mem(priv, base + 11 * sizeof(u32));
+
+ IWL_ERR(priv, "Desc Time "
+ "data1 data2 line\n");
+ IWL_ERR(priv, "%-28s (#%02d) %010u 0x%08X 0x%08X %u\n",
+ desc_lookup(desc), desc, time, data1, data2, line);
+ IWL_ERR(priv, "blink1 blink2 ilink1 ilink2\n");
+ IWL_ERR(priv, "0x%05X 0x%05X 0x%05X 0x%05X\n", blink1, blink2,
+ ilink1, ilink2);
+
+}
+
+#define EVENT_START_OFFSET (4 * sizeof(u32))
+
+/**
+ * iwl_print_event_log - Dump error event log to syslog
+ *
+ */
+static void iwl_print_event_log(struct iwl_priv *priv, u32 start_idx,
+ u32 num_events, u32 mode)
+{
+ u32 i;
+ u32 base; /* SRAM byte address of event log header */
+ u32 event_size; /* 2 u32s, or 3 u32s if timestamp recorded */
+ u32 ptr; /* SRAM byte address of log data */
+ u32 ev, time, data; /* event log data */
+
+ if (num_events == 0)
+ return;
+ if (priv->ucode_type == UCODE_INIT)
+ base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr);
+ else
+ base = le32_to_cpu(priv->card_alive.log_event_table_ptr);
+
+ if (mode == 0)
+ event_size = 2 * sizeof(u32);
+ else
+ event_size = 3 * sizeof(u32);
+
+ ptr = base + EVENT_START_OFFSET + (start_idx * event_size);
+
+ /* "time" is actually "data" for mode 0 (no timestamp).
+ * place event id # at far right for easier visual parsing. */
+ for (i = 0; i < num_events; i++) {
+ ev = iwl_read_targ_mem(priv, ptr);
+ ptr += sizeof(u32);
+ time = iwl_read_targ_mem(priv, ptr);
+ ptr += sizeof(u32);
+ if (mode == 0) {
+ /* data, ev */
+ IWL_ERR(priv, "EVT_LOG:0x%08x:%04u\n", time, ev);
+ } else {
+ data = iwl_read_targ_mem(priv, ptr);
+ ptr += sizeof(u32);
+ IWL_ERR(priv, "EVT_LOGT:%010u:0x%08x:%04u\n",
+ time, data, ev);
+ }
+ }
+}
+
+void iwl_dump_nic_event_log(struct iwl_priv *priv)
+{
+ u32 base; /* SRAM byte address of event log header */
+ u32 capacity; /* event log capacity in # entries */
+ u32 mode; /* 0 - no timestamp, 1 - timestamp recorded */
+ u32 num_wraps; /* # times uCode wrapped to top of log */
+ u32 next_entry; /* index of next entry to be written by uCode */
+ u32 size; /* # entries that we'll print */
+
+ if (priv->ucode_type == UCODE_INIT)
+ base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr);
+ else
+ base = le32_to_cpu(priv->card_alive.log_event_table_ptr);
+
+ if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) {
+ IWL_ERR(priv, "Invalid event log pointer 0x%08X\n", base);
+ return;
+ }
+
+ /* event log header */
+ capacity = iwl_read_targ_mem(priv, base);
+ mode = iwl_read_targ_mem(priv, base + (1 * sizeof(u32)));
+ num_wraps = iwl_read_targ_mem(priv, base + (2 * sizeof(u32)));
+ next_entry = iwl_read_targ_mem(priv, base + (3 * sizeof(u32)));
+
+ size = num_wraps ? capacity : next_entry;
+
+ /* bail out if nothing in log */
+ if (size == 0) {
+ IWL_ERR(priv, "Start IWL Event Log Dump: nothing in log\n");
+ return;
+ }
+
+ IWL_ERR(priv, "Start IWL Event Log Dump: display count %d, wraps %d\n",
+ size, num_wraps);
+
+ /* if uCode has wrapped back to top of log, start at the oldest entry,
+ * i.e the next one that uCode would fill. */
+ if (num_wraps)
+ iwl_print_event_log(priv, next_entry,
+ capacity - next_entry, mode);
+ /* (then/else) start at top of log */
+ iwl_print_event_log(priv, 0, next_entry, mode);
+
+}
+#endif
+
/**
* iwl_alive_start - called after REPLY_ALIVE notification received
* from protocol/runtime uCode (initialization uCode's
IWL_DEBUG_RADIO(priv, "u8[6] bssid_addr: %pM\n", rxon->bssid_addr);
IWL_DEBUG_RADIO(priv, "u16 assoc_id: 0x%x\n", le16_to_cpu(rxon->assoc_id));
}
-
-static const char *desc_lookup_text[] = {
- "OK",
- "FAIL",
- "BAD_PARAM",
- "BAD_CHECKSUM",
- "NMI_INTERRUPT_WDG",
- "SYSASSERT",
- "FATAL_ERROR",
- "BAD_COMMAND",
- "HW_ERROR_TUNE_LOCK",
- "HW_ERROR_TEMPERATURE",
- "ILLEGAL_CHAN_FREQ",
- "VCC_NOT_STABLE",
- "FH_ERROR",
- "NMI_INTERRUPT_HOST",
- "NMI_INTERRUPT_ACTION_PT",
- "NMI_INTERRUPT_UNKNOWN",
- "UCODE_VERSION_MISMATCH",
- "HW_ERROR_ABS_LOCK",
- "HW_ERROR_CAL_LOCK_FAIL",
- "NMI_INTERRUPT_INST_ACTION_PT",
- "NMI_INTERRUPT_DATA_ACTION_PT",
- "NMI_TRM_HW_ER",
- "NMI_INTERRUPT_TRM",
- "NMI_INTERRUPT_BREAK_POINT"
- "DEBUG_0",
- "DEBUG_1",
- "DEBUG_2",
- "DEBUG_3",
- "UNKNOWN"
-};
-
-static const char *desc_lookup(int i)
-{
- int max = ARRAY_SIZE(desc_lookup_text) - 1;
-
- if (i < 0 || i > max)
- i = max;
-
- return desc_lookup_text[i];
-}
-
-#define ERROR_START_OFFSET (1 * sizeof(u32))
-#define ERROR_ELEM_SIZE (7 * sizeof(u32))
-
-static void iwl_dump_nic_error_log(struct iwl_priv *priv)
-{
- u32 data2, line;
- u32 desc, time, count, base, data1;
- u32 blink1, blink2, ilink1, ilink2;
-
- if (priv->ucode_type == UCODE_INIT)
- base = le32_to_cpu(priv->card_alive_init.error_event_table_ptr);
- else
- base = le32_to_cpu(priv->card_alive.error_event_table_ptr);
-
- if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) {
- IWL_ERR(priv, "Not valid error log pointer 0x%08X\n", base);
- return;
- }
-
- count = iwl_read_targ_mem(priv, base);
-
- if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) {
- IWL_ERR(priv, "Start IWL Error Log Dump:\n");
- IWL_ERR(priv, "Status: 0x%08lX, count: %d\n",
- priv->status, count);
- }
-
- desc = iwl_read_targ_mem(priv, base + 1 * sizeof(u32));
- blink1 = iwl_read_targ_mem(priv, base + 3 * sizeof(u32));
- blink2 = iwl_read_targ_mem(priv, base + 4 * sizeof(u32));
- ilink1 = iwl_read_targ_mem(priv, base + 5 * sizeof(u32));
- ilink2 = iwl_read_targ_mem(priv, base + 6 * sizeof(u32));
- data1 = iwl_read_targ_mem(priv, base + 7 * sizeof(u32));
- data2 = iwl_read_targ_mem(priv, base + 8 * sizeof(u32));
- line = iwl_read_targ_mem(priv, base + 9 * sizeof(u32));
- time = iwl_read_targ_mem(priv, base + 11 * sizeof(u32));
-
- IWL_ERR(priv, "Desc Time "
- "data1 data2 line\n");
- IWL_ERR(priv, "%-28s (#%02d) %010u 0x%08X 0x%08X %u\n",
- desc_lookup(desc), desc, time, data1, data2, line);
- IWL_ERR(priv, "blink1 blink2 ilink1 ilink2\n");
- IWL_ERR(priv, "0x%05X 0x%05X 0x%05X 0x%05X\n", blink1, blink2,
- ilink1, ilink2);
-
-}
-
-#define EVENT_START_OFFSET (4 * sizeof(u32))
-
-/**
- * iwl_print_event_log - Dump error event log to syslog
- *
- */
-static void iwl_print_event_log(struct iwl_priv *priv, u32 start_idx,
- u32 num_events, u32 mode)
-{
- u32 i;
- u32 base; /* SRAM byte address of event log header */
- u32 event_size; /* 2 u32s, or 3 u32s if timestamp recorded */
- u32 ptr; /* SRAM byte address of log data */
- u32 ev, time, data; /* event log data */
-
- if (num_events == 0)
- return;
- if (priv->ucode_type == UCODE_INIT)
- base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr);
- else
- base = le32_to_cpu(priv->card_alive.log_event_table_ptr);
-
- if (mode == 0)
- event_size = 2 * sizeof(u32);
- else
- event_size = 3 * sizeof(u32);
-
- ptr = base + EVENT_START_OFFSET + (start_idx * event_size);
-
- /* "time" is actually "data" for mode 0 (no timestamp).
- * place event id # at far right for easier visual parsing. */
- for (i = 0; i < num_events; i++) {
- ev = iwl_read_targ_mem(priv, ptr);
- ptr += sizeof(u32);
- time = iwl_read_targ_mem(priv, ptr);
- ptr += sizeof(u32);
- if (mode == 0) {
- /* data, ev */
- IWL_ERR(priv, "EVT_LOG:0x%08x:%04u\n", time, ev);
- } else {
- data = iwl_read_targ_mem(priv, ptr);
- ptr += sizeof(u32);
- IWL_ERR(priv, "EVT_LOGT:%010u:0x%08x:%04u\n",
- time, data, ev);
- }
- }
-}
-
-void iwl_dump_nic_event_log(struct iwl_priv *priv)
-{
- u32 base; /* SRAM byte address of event log header */
- u32 capacity; /* event log capacity in # entries */
- u32 mode; /* 0 - no timestamp, 1 - timestamp recorded */
- u32 num_wraps; /* # times uCode wrapped to top of log */
- u32 next_entry; /* index of next entry to be written by uCode */
- u32 size; /* # entries that we'll print */
-
- if (priv->ucode_type == UCODE_INIT)
- base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr);
- else
- base = le32_to_cpu(priv->card_alive.log_event_table_ptr);
-
- if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) {
- IWL_ERR(priv, "Invalid event log pointer 0x%08X\n", base);
- return;
- }
-
- /* event log header */
- capacity = iwl_read_targ_mem(priv, base);
- mode = iwl_read_targ_mem(priv, base + (1 * sizeof(u32)));
- num_wraps = iwl_read_targ_mem(priv, base + (2 * sizeof(u32)));
- next_entry = iwl_read_targ_mem(priv, base + (3 * sizeof(u32)));
-
- size = num_wraps ? capacity : next_entry;
-
- /* bail out if nothing in log */
- if (size == 0) {
- IWL_ERR(priv, "Start IWL Event Log Dump: nothing in log\n");
- return;
- }
-
- IWL_ERR(priv, "Start IWL Event Log Dump: display count %d, wraps %d\n",
- size, num_wraps);
-
- /* if uCode has wrapped back to top of log, start at the oldest entry,
- * i.e the next one that uCode would fill. */
- if (num_wraps)
- iwl_print_event_log(priv, next_entry,
- capacity - next_entry, mode);
- /* (then/else) start at top of log */
- iwl_print_event_log(priv, 0, next_entry, mode);
-
-}
#endif
/**
* iwl_irq_handle_error - called for HW or SW error interrupt from card
#ifdef CONFIG_IWLWIFI_DEBUG
if (iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS) {
- iwl_dump_nic_error_log(priv);
- iwl_dump_nic_event_log(priv);
+ priv->cfg->ops->lib->dump_nic_error_log(priv);
+ priv->cfg->ops->lib->dump_nic_event_log(priv);
iwl_print_rx_config_cmd(priv);
}
#endif
int (*is_valid_rtc_data_addr)(u32 addr);
/* 1st ucode load */
int (*load_ucode)(struct iwl_priv *priv);
+ void (*dump_nic_event_log)(struct iwl_priv *priv);
+ void (*dump_nic_error_log)(struct iwl_priv *priv);
/* power management */
struct iwl_apm_ops apm_ops;
/*****************************************************
* Error Handling Debugging
******************************************************/
+#ifdef CONFIG_IWLWIFI_DEBUG
void iwl_dump_nic_event_log(struct iwl_priv *priv);
+void iwl_dump_nic_error_log(struct iwl_priv *priv);
+#else
+static inline void iwl_dump_nic_event_log(struct iwl_priv *priv)
+{
+}
+
+static inline void iwl_dump_nic_error_log(struct iwl_priv *priv)
+{
+}
+#endif
+
void iwl_clear_isr_stats(struct iwl_priv *priv);
/*****************************************************
pos += scnprintf(buf + pos, buf_size - pos, "0x%.4x ", ofs);
hex_dump_to_buffer(ptr + ofs, 16 , 16, 2, buf + pos,
buf_size - pos, 0);
- pos += strlen(buf);
+ pos += strlen(buf + pos);
if (buf_size - pos > 0)
buf[pos++] = '\n';
}
if (sscanf(buf, "%d", &event_log_flag) != 1)
return -EFAULT;
if (event_log_flag == 1)
- iwl_dump_nic_event_log(priv);
+ priv->cfg->ops->lib->dump_nic_event_log(priv);
return count;
}
"0x%.4x ", ofs);
hex_dump_to_buffer(ptr + ofs, 16, 16, 2,
buf + pos, bufsz - pos, 0);
- pos += strlen(buf);
+ pos += strlen(buf + pos);
if (bufsz - pos > 0)
buf[pos++] = '\n';
}
"0x%.4x ", ofs);
hex_dump_to_buffer(ptr + ofs, 16, 16, 2,
buf + pos, bufsz - pos, 0);
- pos += strlen(buf);
+ pos += strlen(buf + pos);
if (bufsz - pos > 0)
buf[pos++] = '\n';
}
}
spin_unlock_irqrestore(&rxq->lock, flags);
+ if (rxq->free_count > RX_LOW_WATERMARK)
+ priority |= __GFP_NOWARN;
/* Alloc a new receive buffer */
skb = alloc_skb(priv->hw_params.rx_buf_size + 256,
priority);
if (!skb) {
- IWL_CRIT(priv, "Can not allocate SKB buffers\n");
+ if (net_ratelimit())
+ IWL_DEBUG_INFO(priv, "Failed to allocate SKB buffer.\n");
+ if ((rxq->free_count <= RX_LOW_WATERMARK) &&
+ net_ratelimit())
+ IWL_CRIT(priv, "Failed to allocate SKB buffer with %s. Only %u free buffers remaining.\n",
+ priority == GFP_ATOMIC ? "GFP_ATOMIC" : "GFP_KERNEL",
+ rxq->free_count);
/* We don't reschedule replenish work here -- we will
* call the restock method and if it still needs
* more buffers it will schedule replenish */
struct iwl_host_cmd cmd = {
.id = REPLY_WEPKEY,
.data = wep_cmd,
- .flags = CMD_SYNC,
+ .flags = CMD_ASYNC,
};
memset(wep_cmd, 0, cmd_size +
pci_free_consistent(dev, priv->hw_params.tfd_size *
txq->q.n_bd, txq->tfds, txq->q.dma_addr);
+ /* deallocate arrays */
+ kfree(txq->cmd);
+ kfree(txq->meta);
+ txq->cmd = NULL;
+ txq->meta = NULL;
+
/* 0-fill queue descriptor structure */
memset(txq, 0, sizeof(*txq));
}
}
spin_unlock_irqrestore(&rxq->lock, flags);
+ if (rxq->free_count > RX_LOW_WATERMARK)
+ priority |= __GFP_NOWARN;
/* Alloc a new receive buffer */
skb = alloc_skb(priv->hw_params.rx_buf_size, priority);
if (!skb) {
if (net_ratelimit())
- IWL_CRIT(priv, ": Can not allocate SKB buffers\n");
+ IWL_DEBUG_INFO(priv, "Failed to allocate SKB buffer.\n");
+ if ((rxq->free_count <= RX_LOW_WATERMARK) &&
+ net_ratelimit())
+ IWL_CRIT(priv, "Failed to allocate SKB buffer with %s. Only %u free buffers remaining.\n",
+ priority == GFP_ATOMIC ? "GFP_ATOMIC" : "GFP_KERNEL",
+ rxq->free_count);
/* We don't reschedule replenish work here -- we will
* call the restock method and if it still needs
* more buffers it will schedule replenish */
tasklet_kill(&priv->irq_tasklet);
}
+#ifdef CONFIG_IWLWIFI_DEBUG
static const char *desc_lookup(int i)
{
switch (i) {
#define ERROR_START_OFFSET (1 * sizeof(u32))
#define ERROR_ELEM_SIZE (7 * sizeof(u32))
-static void iwl3945_dump_nic_error_log(struct iwl_priv *priv)
+void iwl3945_dump_nic_error_log(struct iwl_priv *priv)
{
u32 i;
u32 desc, time, count, base, data1;
}
}
-static void iwl3945_dump_nic_event_log(struct iwl_priv *priv)
+void iwl3945_dump_nic_event_log(struct iwl_priv *priv)
{
u32 base; /* SRAM byte address of event log header */
u32 capacity; /* event log capacity in # entries */
iwl3945_print_event_log(priv, 0, next_entry, mode);
}
+#else
+void iwl3945_dump_nic_event_log(struct iwl_priv *priv)
+{
+}
+
+void iwl3945_dump_nic_error_log(struct iwl_priv *priv)
+{
+}
+
+#endif
static void iwl3945_irq_tasklet(struct iwl_priv *priv)
{
static DEVICE_ATTR(dump_errors, S_IWUSR, NULL, dump_error_log);
-static ssize_t dump_event_log(struct device *d,
- struct device_attribute *attr,
- const char *buf, size_t count)
-{
- struct iwl_priv *priv = dev_get_drvdata(d);
- char *p = (char *)buf;
-
- if (p[0] == '1')
- iwl3945_dump_nic_event_log(priv);
-
- return strnlen(buf, count);
-}
-
-static DEVICE_ATTR(dump_events, S_IWUSR, NULL, dump_event_log);
-
/*****************************************************************************
*
* driver setup and tear down
&dev_attr_antenna.attr,
&dev_attr_channels.attr,
&dev_attr_dump_errors.attr,
- &dev_attr_dump_events.attr,
&dev_attr_flags.attr,
&dev_attr_filter_flags.attr,
#ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT
data->beacon_int = 1024 * info->beacon_int / 1000 * HZ / 1000;
if (WARN_ON(!data->beacon_int))
data->beacon_int = 1;
+ if (data->started)
+ mod_timer(&data->beacon_timer,
+ jiffies + data->beacon_int);
}
if (changed & BSS_CHANGED_ERP_CTS_PROT) {
{
}
-static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, bool l2pad,
+static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb,
unsigned int header_length,
struct rxdone_entry_desc *rxdesc)
{
/* Huawei-3Com */
{ USB_DEVICE(0x1472, 0x0009), USB_DEVICE_DATA(&rt73usb_ops) },
/* Hercules */
+ { USB_DEVICE(0x06f8, 0xe002), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x06f8, 0xe010), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x06f8, 0xe020), USB_DEVICE_DATA(&rt73usb_ops) },
/* Linksys */
menuconfig WL12XX
- boolean "TI wl12xx driver support"
+ tristate "TI wl12xx driver support"
depends on MAC80211 && WLAN_80211 && EXPERIMENTAL
---help---
This will enable TI wl12xx driver support. The drivers make
/* Find bulk out endpoint */
endpoint = &iface_desc->endpoint[1].desc;
- if ((endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT &&
+ if (usb_endpoint_dir_out(endpoint) &&
usb_endpoint_xfer_bulk(endpoint)) {
bulk_out_ep = endpoint->bEndpointAddress;
} else {
}
/* Enable the Rx interrupts for the first buffer */
- reg_data = in_be32(drvdata->base_addr + XEL_RSR_OFFSET);
out_be32(drvdata->base_addr + XEL_RSR_OFFSET,
- reg_data | XEL_RSR_RECV_IE_MASK);
+ XEL_RSR_RECV_IE_MASK);
/* Enable the Rx interrupts for the second Buffer if
* configured in HW */
if (drvdata->rx_ping_pong != 0) {
- reg_data = in_be32(drvdata->base_addr + XEL_BUFFER_OFFSET +
- XEL_RSR_OFFSET);
out_be32(drvdata->base_addr + XEL_BUFFER_OFFSET +
XEL_RSR_OFFSET,
- reg_data | XEL_RSR_RECV_IE_MASK);
+ XEL_RSR_RECV_IE_MASK);
}
/* Enable the Global Interrupt Enable */
#define PARPORT_MIN_SPINTIME_VALUE 1
#define PARPORT_MAX_SPINTIME_VALUE 1000
-static int do_active_device(ctl_table *table, int write, struct file *filp,
+static int do_active_device(ctl_table *table, int write,
void __user *result, size_t *lenp, loff_t *ppos)
{
struct parport *port = (struct parport *)table->extra1;
}
#ifdef CONFIG_PARPORT_1284
-static int do_autoprobe(ctl_table *table, int write, struct file *filp,
+static int do_autoprobe(ctl_table *table, int write,
void __user *result, size_t *lenp, loff_t *ppos)
{
struct parport_device_info *info = table->extra2;
#endif /* IEEE1284.3 support. */
static int do_hardware_base_addr (ctl_table *table, int write,
- struct file *filp, void __user *result,
+ void __user *result,
size_t *lenp, loff_t *ppos)
{
struct parport *port = (struct parport *)table->extra1;
}
static int do_hardware_irq (ctl_table *table, int write,
- struct file *filp, void __user *result,
+ void __user *result,
size_t *lenp, loff_t *ppos)
{
struct parport *port = (struct parport *)table->extra1;
}
static int do_hardware_dma (ctl_table *table, int write,
- struct file *filp, void __user *result,
+ void __user *result,
size_t *lenp, loff_t *ppos)
{
struct parport *port = (struct parport *)table->extra1;
}
static int do_hardware_modes (ctl_table *table, int write,
- struct file *filp, void __user *result,
+ void __user *result,
size_t *lenp, loff_t *ppos)
{
struct parport *port = (struct parport *)table->extra1;
__func__, status);
return retval;
}
- info->hardware_id.string[sizeof(info->hardware_id.length) - 1] = '\0';
if (info->current_status && (info->valid & ACPI_VALID_HID) &&
(!strcmp(info->hardware_id.string, IBM_HARDWARE_ID1) ||
#define SLOT_NAME_SIZE 10
struct slot {
- u8 bus;
- u8 device;
u8 state;
- u8 hp_slot;
- u32 number;
struct controller *ctrl;
- struct hpc_ops *hpc_ops;
struct hotplug_slot *hotplug_slot;
- struct list_head slot_list;
struct delayed_work work; /* work for button event */
struct mutex lock;
};
};
struct controller {
- struct mutex crit_sect; /* critical section mutex */
struct mutex ctrl_lock; /* controller lock */
- int num_slots; /* Number of slots on ctlr */
- int slot_num_inc; /* 1 or -1 */
- struct pci_dev *pci_dev;
struct pcie_device *pcie; /* PCI Express port service */
- struct list_head slot_list;
- struct hpc_ops *hpc_ops;
+ struct slot *slot;
wait_queue_head_t queue; /* sleep & wake process */
- u8 slot_device_offset;
- u32 first_slot; /* First physical slot number */ /* PCIE only has 1 slot */
- u8 slot_bus; /* Bus where the slots handled by this controller sit */
u32 slot_cap;
u8 cap_base;
struct timer_list poll_timer;
#define POWERON_STATE 3
#define POWEROFF_STATE 4
-/* Error messages */
-#define INTERLOCK_OPEN 0x00000002
-#define ADD_NOT_SUPPORTED 0x00000003
-#define CARD_FUNCTIONING 0x00000005
-#define ADAPTER_NOT_SAME 0x00000006
-#define NO_ADAPTER_PRESENT 0x00000009
-#define NOT_ENOUGH_RESOURCES 0x0000000B
-#define DEVICE_TYPE_NOT_SUPPORTED 0x0000000C
-#define WRONG_BUS_FREQUENCY 0x0000000D
-#define POWER_FAILURE 0x0000000E
-
-/* Field definitions in Slot Capabilities Register */
-#define ATTN_BUTTN_PRSN 0x00000001
-#define PWR_CTRL_PRSN 0x00000002
-#define MRL_SENS_PRSN 0x00000004
-#define ATTN_LED_PRSN 0x00000008
-#define PWR_LED_PRSN 0x00000010
-#define HP_SUPR_RM_SUP 0x00000020
-#define EMI_PRSN 0x00020000
-#define NO_CMD_CMPL_SUP 0x00040000
-
-#define ATTN_BUTTN(ctrl) ((ctrl)->slot_cap & ATTN_BUTTN_PRSN)
-#define POWER_CTRL(ctrl) ((ctrl)->slot_cap & PWR_CTRL_PRSN)
-#define MRL_SENS(ctrl) ((ctrl)->slot_cap & MRL_SENS_PRSN)
-#define ATTN_LED(ctrl) ((ctrl)->slot_cap & ATTN_LED_PRSN)
-#define PWR_LED(ctrl) ((ctrl)->slot_cap & PWR_LED_PRSN)
-#define HP_SUPR_RM(ctrl) ((ctrl)->slot_cap & HP_SUPR_RM_SUP)
-#define EMI(ctrl) ((ctrl)->slot_cap & EMI_PRSN)
-#define NO_CMD_CMPL(ctrl) ((ctrl)->slot_cap & NO_CMD_CMPL_SUP)
+#define ATTN_BUTTN(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_ABP)
+#define POWER_CTRL(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_PCP)
+#define MRL_SENS(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_MRLSP)
+#define ATTN_LED(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_AIP)
+#define PWR_LED(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_PIP)
+#define HP_SUPR_RM(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_HPS)
+#define EMI(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_EIP)
+#define NO_CMD_CMPL(ctrl) ((ctrl)->slot_cap & PCI_EXP_SLTCAP_NCCS)
+#define PSN(ctrl) ((ctrl)->slot_cap >> 19)
extern int pciehp_sysfs_enable_slot(struct slot *slot);
extern int pciehp_sysfs_disable_slot(struct slot *slot);
extern u8 pciehp_handle_attention_button(struct slot *p_slot);
- extern u8 pciehp_handle_switch_change(struct slot *p_slot);
+extern u8 pciehp_handle_switch_change(struct slot *p_slot);
extern u8 pciehp_handle_presence_change(struct slot *p_slot);
extern u8 pciehp_handle_power_fault(struct slot *p_slot);
extern int pciehp_configure_device(struct slot *p_slot);
int pciehp_enable_slot(struct slot *p_slot);
int pciehp_disable_slot(struct slot *p_slot);
int pcie_enable_notification(struct controller *ctrl);
+int pciehp_power_on_slot(struct slot *slot);
+int pciehp_power_off_slot(struct slot *slot);
+int pciehp_get_power_status(struct slot *slot, u8 *status);
+int pciehp_get_attention_status(struct slot *slot, u8 *status);
+
+int pciehp_set_attention_status(struct slot *slot, u8 status);
+int pciehp_get_latch_status(struct slot *slot, u8 *status);
+int pciehp_get_adapter_status(struct slot *slot, u8 *status);
+int pciehp_get_max_link_speed(struct slot *slot, enum pci_bus_speed *speed);
+int pciehp_get_max_link_width(struct slot *slot, enum pcie_link_width *val);
+int pciehp_get_cur_link_speed(struct slot *slot, enum pci_bus_speed *speed);
+int pciehp_get_cur_link_width(struct slot *slot, enum pcie_link_width *val);
+int pciehp_query_power_fault(struct slot *slot);
+void pciehp_green_led_on(struct slot *slot);
+void pciehp_green_led_off(struct slot *slot);
+void pciehp_green_led_blink(struct slot *slot);
+int pciehp_check_link_status(struct controller *ctrl);
+void pciehp_release_ctrl(struct controller *ctrl);
static inline const char *slot_name(struct slot *slot)
{
return hotplug_slot_name(slot->hotplug_slot);
}
-static inline struct slot *pciehp_find_slot(struct controller *ctrl, u8 device)
-{
- struct slot *slot;
-
- list_for_each_entry(slot, &ctrl->slot_list, slot_list) {
- if (slot->device == device)
- return slot;
- }
-
- ctrl_err(ctrl, "Slot (device=0x%02x) not found\n", device);
- return NULL;
-}
-
-struct hpc_ops {
- int (*power_on_slot)(struct slot *slot);
- int (*power_off_slot)(struct slot *slot);
- int (*get_power_status)(struct slot *slot, u8 *status);
- int (*get_attention_status)(struct slot *slot, u8 *status);
- int (*set_attention_status)(struct slot *slot, u8 status);
- int (*get_latch_status)(struct slot *slot, u8 *status);
- int (*get_adapter_status)(struct slot *slot, u8 *status);
- int (*get_max_bus_speed)(struct slot *slot, enum pci_bus_speed *speed);
- int (*get_cur_bus_speed)(struct slot *slot, enum pci_bus_speed *speed);
- int (*get_max_lnk_width)(struct slot *slot, enum pcie_link_width *val);
- int (*get_cur_lnk_width)(struct slot *slot, enum pcie_link_width *val);
- int (*query_power_fault)(struct slot *slot);
- void (*green_led_on)(struct slot *slot);
- void (*green_led_off)(struct slot *slot);
- void (*green_led_blink)(struct slot *slot);
- void (*release_ctlr)(struct controller *ctrl);
- int (*check_lnk_status)(struct controller *ctrl);
-};
-
#ifdef CONFIG_ACPI
#include <acpi/acpi.h>
#include <acpi/acpi_bus.h>
#define PCIEHP_DETECT_AUTO (2)
#define PCIEHP_DETECT_DEFAULT PCIEHP_DETECT_AUTO
+struct dummy_slot {
+ u32 number;
+ struct list_head list;
+};
+
static int slot_detection_mode;
static char *pciehp_detect_mode;
module_param(pciehp_detect_mode, charp, 0444);
int pos;
u32 slot_cap;
acpi_handle handle;
- struct slot *slot, *tmp;
+ struct dummy_slot *slot, *tmp;
struct pci_dev *pdev = dev->port;
/* Note: pciehp_detect_mode != PCIEHP_DETECT_ACPI here */
if (pciehp_get_hp_hw_control_from_firmware(pdev))
if (!slot)
return -ENOMEM;
slot->number = slot_cap >> 19;
- list_for_each_entry(tmp, &dummy_slots, slot_list) {
+ list_for_each_entry(tmp, &dummy_slots, list) {
if (tmp->number == slot->number)
dup_slot_id++;
}
- list_add_tail(&slot->slot_list, &dummy_slots);
+ list_add_tail(&slot->list, &dummy_slots);
handle = DEVICE_ACPI_HANDLE(&pdev->dev);
if (!acpi_slot_detected && acpi_pci_detect_ejectable(handle))
acpi_slot_detected = 1;
static int __init select_detection_mode(void)
{
- struct slot *slot, *tmp;
+ struct dummy_slot *slot, *tmp;
pcie_port_service_register(&dummy_driver);
pcie_port_service_unregister(&dummy_driver);
- list_for_each_entry_safe(slot, tmp, &dummy_slots, slot_list) {
- list_del(&slot->slot_list);
+ list_for_each_entry_safe(slot, tmp, &dummy_slots, list) {
+ list_del(&slot->list);
kfree(slot);
}
if (acpi_slot_detected && dup_slot_id)
kfree(hotplug_slot);
}
-static int init_slots(struct controller *ctrl)
+static int init_slot(struct controller *ctrl)
{
- struct slot *slot;
- struct hotplug_slot *hotplug_slot;
- struct hotplug_slot_info *info;
+ struct slot *slot = ctrl->slot;
+ struct hotplug_slot *hotplug = NULL;
+ struct hotplug_slot_info *info = NULL;
char name[SLOT_NAME_SIZE];
int retval = -ENOMEM;
- list_for_each_entry(slot, &ctrl->slot_list, slot_list) {
- hotplug_slot = kzalloc(sizeof(*hotplug_slot), GFP_KERNEL);
- if (!hotplug_slot)
- goto error;
-
- info = kzalloc(sizeof(*info), GFP_KERNEL);
- if (!info)
- goto error_hpslot;
-
- /* register this slot with the hotplug pci core */
- hotplug_slot->info = info;
- hotplug_slot->private = slot;
- hotplug_slot->release = &release_slot;
- hotplug_slot->ops = &pciehp_hotplug_slot_ops;
- slot->hotplug_slot = hotplug_slot;
- snprintf(name, SLOT_NAME_SIZE, "%u", slot->number);
-
- ctrl_dbg(ctrl, "Registering domain:bus:dev=%04x:%02x:%02x "
- "hp_slot=%x sun=%x slot_device_offset=%x\n",
- pci_domain_nr(ctrl->pci_dev->subordinate),
- slot->bus, slot->device, slot->hp_slot, slot->number,
- ctrl->slot_device_offset);
- retval = pci_hp_register(hotplug_slot,
- ctrl->pci_dev->subordinate,
- slot->device,
- name);
- if (retval) {
- ctrl_err(ctrl, "pci_hp_register failed with error %d\n",
- retval);
- goto error_info;
- }
- get_power_status(hotplug_slot, &info->power_status);
- get_attention_status(hotplug_slot, &info->attention_status);
- get_latch_status(hotplug_slot, &info->latch_status);
- get_adapter_status(hotplug_slot, &info->adapter_status);
+ hotplug = kzalloc(sizeof(*hotplug), GFP_KERNEL);
+ if (!hotplug)
+ goto out;
+
+ info = kzalloc(sizeof(*info), GFP_KERNEL);
+ if (!info)
+ goto out;
+
+ /* register this slot with the hotplug pci core */
+ hotplug->info = info;
+ hotplug->private = slot;
+ hotplug->release = &release_slot;
+ hotplug->ops = &pciehp_hotplug_slot_ops;
+ slot->hotplug_slot = hotplug;
+ snprintf(name, SLOT_NAME_SIZE, "%u", PSN(ctrl));
+
+ ctrl_dbg(ctrl, "Registering domain:bus:dev=%04x:%02x:00 sun=%x\n",
+ pci_domain_nr(ctrl->pcie->port->subordinate),
+ ctrl->pcie->port->subordinate->number, PSN(ctrl));
+ retval = pci_hp_register(hotplug,
+ ctrl->pcie->port->subordinate, 0, name);
+ if (retval) {
+ ctrl_err(ctrl,
+ "pci_hp_register failed with error %d\n", retval);
+ goto out;
+ }
+ get_power_status(hotplug, &info->power_status);
+ get_attention_status(hotplug, &info->attention_status);
+ get_latch_status(hotplug, &info->latch_status);
+ get_adapter_status(hotplug, &info->adapter_status);
+out:
+ if (retval) {
+ kfree(info);
+ kfree(hotplug);
}
-
- return 0;
-error_info:
- kfree(info);
-error_hpslot:
- kfree(hotplug_slot);
-error:
return retval;
}
-static void cleanup_slots(struct controller *ctrl)
+static void cleanup_slot(struct controller *ctrl)
{
- struct slot *slot;
- list_for_each_entry(slot, &ctrl->slot_list, slot_list)
- pci_hp_deregister(slot->hotplug_slot);
+ pci_hp_deregister(ctrl->slot->hotplug_slot);
}
/*
hotplug_slot->info->attention_status = status;
if (ATTN_LED(slot->ctrl))
- slot->hpc_ops->set_attention_status(slot, status);
+ pciehp_set_attention_status(slot, status);
return 0;
}
ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
__func__, slot_name(slot));
- retval = slot->hpc_ops->get_power_status(slot, value);
+ retval = pciehp_get_power_status(slot, value);
if (retval < 0)
*value = hotplug_slot->info->power_status;
ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
__func__, slot_name(slot));
- retval = slot->hpc_ops->get_attention_status(slot, value);
+ retval = pciehp_get_attention_status(slot, value);
if (retval < 0)
*value = hotplug_slot->info->attention_status;
ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
__func__, slot_name(slot));
- retval = slot->hpc_ops->get_latch_status(slot, value);
+ retval = pciehp_get_latch_status(slot, value);
if (retval < 0)
*value = hotplug_slot->info->latch_status;
ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
__func__, slot_name(slot));
- retval = slot->hpc_ops->get_adapter_status(slot, value);
+ retval = pciehp_get_adapter_status(slot, value);
if (retval < 0)
*value = hotplug_slot->info->adapter_status;
ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
__func__, slot_name(slot));
- retval = slot->hpc_ops->get_max_bus_speed(slot, value);
+ retval = pciehp_get_max_link_speed(slot, value);
if (retval < 0)
*value = PCI_SPEED_UNKNOWN;
ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
__func__, slot_name(slot));
- retval = slot->hpc_ops->get_cur_bus_speed(slot, value);
+ retval = pciehp_get_cur_link_speed(slot, value);
if (retval < 0)
*value = PCI_SPEED_UNKNOWN;
{
int rc;
struct controller *ctrl;
- struct slot *t_slot;
+ struct slot *slot;
u8 value;
struct pci_dev *pdev = dev->port;
set_service_data(dev, ctrl);
/* Setup the slot information structures */
- rc = init_slots(ctrl);
+ rc = init_slot(ctrl);
if (rc) {
if (rc == -EBUSY)
ctrl_warn(ctrl, "Slot already registered by another "
}
/* Check if slot is occupied */
- t_slot = pciehp_find_slot(ctrl, ctrl->slot_device_offset);
- t_slot->hpc_ops->get_adapter_status(t_slot, &value);
+ slot = ctrl->slot;
+ pciehp_get_adapter_status(slot, &value);
if (value) {
if (pciehp_force)
- pciehp_enable_slot(t_slot);
+ pciehp_enable_slot(slot);
} else {
/* Power off slot if not occupied */
if (POWER_CTRL(ctrl)) {
- rc = t_slot->hpc_ops->power_off_slot(t_slot);
+ rc = pciehp_power_off_slot(slot);
if (rc)
goto err_out_free_ctrl_slot;
}
return 0;
err_out_free_ctrl_slot:
- cleanup_slots(ctrl);
+ cleanup_slot(ctrl);
err_out_release_ctlr:
- ctrl->hpc_ops->release_ctlr(ctrl);
+ pciehp_release_ctrl(ctrl);
err_out_none:
return -ENODEV;
}
-static void pciehp_remove (struct pcie_device *dev)
+static void pciehp_remove(struct pcie_device *dev)
{
struct controller *ctrl = get_service_data(dev);
- cleanup_slots(ctrl);
- ctrl->hpc_ops->release_ctlr(ctrl);
+ cleanup_slot(ctrl);
+ pciehp_release_ctrl(ctrl);
}
#ifdef CONFIG_PM
dev_info(&dev->device, "%s ENTRY\n", __func__);
if (pciehp_force) {
struct controller *ctrl = get_service_data(dev);
- struct slot *t_slot;
+ struct slot *slot;
u8 status;
/* reinitialize the chipset's event detection logic */
pcie_enable_notification(ctrl);
- t_slot = pciehp_find_slot(ctrl, ctrl->slot_device_offset);
+ slot = ctrl->slot;
/* Check if slot is occupied */
- t_slot->hpc_ops->get_adapter_status(t_slot, &status);
+ pciehp_get_adapter_status(slot, &status);
if (status)
- pciehp_enable_slot(t_slot);
+ pciehp_enable_slot(slot);
else
- pciehp_disable_slot(t_slot);
+ pciehp_disable_slot(slot);
}
return 0;
}
/* Switch Change */
ctrl_dbg(ctrl, "Switch interrupt received\n");
- p_slot->hpc_ops->get_latch_status(p_slot, &getstatus);
+ pciehp_get_latch_status(p_slot, &getstatus);
if (getstatus) {
/*
* Switch opened
/* Switch is open, assume a presence change
* Save the presence state
*/
- p_slot->hpc_ops->get_adapter_status(p_slot, &presence_save);
+ pciehp_get_adapter_status(p_slot, &presence_save);
if (presence_save) {
/*
* Card Present
/* power fault */
ctrl_dbg(ctrl, "Power fault interrupt received\n");
- if ( !(p_slot->hpc_ops->query_power_fault(p_slot))) {
+ if (!pciehp_query_power_fault(p_slot)) {
/*
* power fault Cleared
*/
{
/* turn off slot, turn on Amber LED, turn off Green LED if supported*/
if (POWER_CTRL(ctrl)) {
- if (pslot->hpc_ops->power_off_slot(pslot)) {
+ if (pciehp_power_off_slot(pslot)) {
ctrl_err(ctrl,
"Issue of Slot Power Off command failed\n");
return;
}
if (PWR_LED(ctrl))
- pslot->hpc_ops->green_led_off(pslot);
+ pciehp_green_led_off(pslot);
if (ATTN_LED(ctrl)) {
- if (pslot->hpc_ops->set_attention_status(pslot, 1)) {
+ if (pciehp_set_attention_status(pslot, 1)) {
ctrl_err(ctrl,
"Issue of Set Attention Led command failed\n");
return;
{
int retval = 0;
struct controller *ctrl = p_slot->ctrl;
- struct pci_bus *parent = ctrl->pci_dev->subordinate;
-
- ctrl_dbg(ctrl, "%s: slot device, slot offset, hp slot = %d, %d, %d\n",
- __func__, p_slot->device, ctrl->slot_device_offset,
- p_slot->hp_slot);
+ struct pci_bus *parent = ctrl->pcie->port->subordinate;
if (POWER_CTRL(ctrl)) {
/* Power on slot */
- retval = p_slot->hpc_ops->power_on_slot(p_slot);
+ retval = pciehp_power_on_slot(p_slot);
if (retval)
return retval;
}
if (PWR_LED(ctrl))
- p_slot->hpc_ops->green_led_blink(p_slot);
+ pciehp_green_led_blink(p_slot);
/* Check link training status */
- retval = p_slot->hpc_ops->check_lnk_status(ctrl);
+ retval = pciehp_check_link_status(ctrl);
if (retval) {
ctrl_err(ctrl, "Failed to check link status\n");
set_slot_off(ctrl, p_slot);
}
/* Check for a power fault */
- if (p_slot->hpc_ops->query_power_fault(p_slot)) {
+ if (pciehp_query_power_fault(p_slot)) {
ctrl_dbg(ctrl, "Power fault detected\n");
- retval = POWER_FAILURE;
+ retval = -EIO;
goto err_exit;
}
retval = pciehp_configure_device(p_slot);
if (retval) {
- ctrl_err(ctrl, "Cannot add device at %04x:%02x:%02x\n",
- pci_domain_nr(parent), p_slot->bus, p_slot->device);
+ ctrl_err(ctrl, "Cannot add device at %04x:%02x:00\n",
+ pci_domain_nr(parent), parent->number);
goto err_exit;
}
if (PWR_LED(ctrl))
- p_slot->hpc_ops->green_led_on(p_slot);
+ pciehp_green_led_on(p_slot);
return 0;
if (retval)
return retval;
- ctrl_dbg(ctrl, "%s: hp_slot = %d\n", __func__, p_slot->hp_slot);
-
if (POWER_CTRL(ctrl)) {
/* power off slot */
- retval = p_slot->hpc_ops->power_off_slot(p_slot);
+ retval = pciehp_power_off_slot(p_slot);
if (retval) {
ctrl_err(ctrl,
"Issue of Slot Disable command failed\n");
msleep(1000);
}
+ /* turn off Green LED */
if (PWR_LED(ctrl))
- /* turn off Green LED */
- p_slot->hpc_ops->green_led_off(p_slot);
+ pciehp_green_led_off(p_slot);
return 0;
}
case POWEROFF_STATE:
mutex_unlock(&p_slot->lock);
ctrl_dbg(p_slot->ctrl,
- "Disabling domain:bus:device=%04x:%02x:%02x\n",
- pci_domain_nr(p_slot->ctrl->pci_dev->subordinate),
- p_slot->bus, p_slot->device);
+ "Disabling domain:bus:device=%04x:%02x:00\n",
+ pci_domain_nr(p_slot->ctrl->pcie->port->subordinate),
+ p_slot->ctrl->pcie->port->subordinate->number);
pciehp_disable_slot(p_slot);
mutex_lock(&p_slot->lock);
p_slot->state = STATIC_STATE;
break;
case POWERON_STATE:
mutex_unlock(&p_slot->lock);
- if (pciehp_enable_slot(p_slot) &&
- PWR_LED(p_slot->ctrl))
- p_slot->hpc_ops->green_led_off(p_slot);
+ if (pciehp_enable_slot(p_slot) && PWR_LED(p_slot->ctrl))
+ pciehp_green_led_off(p_slot);
mutex_lock(&p_slot->lock);
p_slot->state = STATIC_STATE;
break;
if (!info)
return -ENOMEM;
- slot->hpc_ops->get_power_status(slot, &(info->power_status));
- slot->hpc_ops->get_attention_status(slot, &(info->attention_status));
- slot->hpc_ops->get_latch_status(slot, &(info->latch_status));
- slot->hpc_ops->get_adapter_status(slot, &(info->adapter_status));
+ pciehp_get_power_status(slot, &info->power_status);
+ pciehp_get_attention_status(slot, &info->attention_status);
+ pciehp_get_latch_status(slot, &info->latch_status);
+ pciehp_get_adapter_status(slot, &info->adapter_status);
result = pci_hp_change_slot_info(slot->hotplug_slot, info);
kfree (info);
switch (p_slot->state) {
case STATIC_STATE:
- p_slot->hpc_ops->get_power_status(p_slot, &getstatus);
+ pciehp_get_power_status(p_slot, &getstatus);
if (getstatus) {
p_slot->state = BLINKINGOFF_STATE;
ctrl_info(ctrl,
}
/* blink green LED and turn off amber */
if (PWR_LED(ctrl))
- p_slot->hpc_ops->green_led_blink(p_slot);
+ pciehp_green_led_blink(p_slot);
if (ATTN_LED(ctrl))
- p_slot->hpc_ops->set_attention_status(p_slot, 0);
+ pciehp_set_attention_status(p_slot, 0);
schedule_delayed_work(&p_slot->work, 5*HZ);
break;
cancel_delayed_work(&p_slot->work);
if (p_slot->state == BLINKINGOFF_STATE) {
if (PWR_LED(ctrl))
- p_slot->hpc_ops->green_led_on(p_slot);
+ pciehp_green_led_on(p_slot);
} else {
if (PWR_LED(ctrl))
- p_slot->hpc_ops->green_led_off(p_slot);
+ pciehp_green_led_off(p_slot);
}
if (ATTN_LED(ctrl))
- p_slot->hpc_ops->set_attention_status(p_slot, 0);
+ pciehp_set_attention_status(p_slot, 0);
ctrl_info(ctrl, "PCI slot #%s - action canceled "
"due to button press\n", slot_name(p_slot));
p_slot->state = STATIC_STATE;
info->p_slot = p_slot;
INIT_WORK(&info->work, pciehp_power_thread);
- p_slot->hpc_ops->get_adapter_status(p_slot, &getstatus);
+ pciehp_get_adapter_status(p_slot, &getstatus);
if (!getstatus)
p_slot->state = POWEROFF_STATE;
else
if (!POWER_CTRL(ctrl))
break;
if (ATTN_LED(ctrl))
- p_slot->hpc_ops->set_attention_status(p_slot, 1);
+ pciehp_set_attention_status(p_slot, 1);
if (PWR_LED(ctrl))
- p_slot->hpc_ops->green_led_off(p_slot);
+ pciehp_green_led_off(p_slot);
break;
case INT_PRESENCE_ON:
case INT_PRESENCE_OFF:
int rc;
struct controller *ctrl = p_slot->ctrl;
- /* Check to see if (latch closed, card present, power off) */
- mutex_lock(&p_slot->ctrl->crit_sect);
-
- rc = p_slot->hpc_ops->get_adapter_status(p_slot, &getstatus);
+ rc = pciehp_get_adapter_status(p_slot, &getstatus);
if (rc || !getstatus) {
ctrl_info(ctrl, "No adapter on slot(%s)\n", slot_name(p_slot));
- mutex_unlock(&p_slot->ctrl->crit_sect);
return -ENODEV;
}
if (MRL_SENS(p_slot->ctrl)) {
- rc = p_slot->hpc_ops->get_latch_status(p_slot, &getstatus);
+ rc = pciehp_get_latch_status(p_slot, &getstatus);
if (rc || getstatus) {
ctrl_info(ctrl, "Latch open on slot(%s)\n",
slot_name(p_slot));
- mutex_unlock(&p_slot->ctrl->crit_sect);
return -ENODEV;
}
}
if (POWER_CTRL(p_slot->ctrl)) {
- rc = p_slot->hpc_ops->get_power_status(p_slot, &getstatus);
+ rc = pciehp_get_power_status(p_slot, &getstatus);
if (rc || getstatus) {
ctrl_info(ctrl, "Already enabled on slot(%s)\n",
slot_name(p_slot));
- mutex_unlock(&p_slot->ctrl->crit_sect);
return -EINVAL;
}
}
- p_slot->hpc_ops->get_latch_status(p_slot, &getstatus);
+ pciehp_get_latch_status(p_slot, &getstatus);
rc = board_added(p_slot);
if (rc) {
- p_slot->hpc_ops->get_latch_status(p_slot, &getstatus);
+ pciehp_get_latch_status(p_slot, &getstatus);
}
update_slot_info(p_slot);
- mutex_unlock(&p_slot->ctrl->crit_sect);
return rc;
}
if (!p_slot->ctrl)
return 1;
- /* Check to see if (latch closed, card present, power on) */
- mutex_lock(&p_slot->ctrl->crit_sect);
-
if (!HP_SUPR_RM(p_slot->ctrl)) {
- ret = p_slot->hpc_ops->get_adapter_status(p_slot, &getstatus);
+ ret = pciehp_get_adapter_status(p_slot, &getstatus);
if (ret || !getstatus) {
ctrl_info(ctrl, "No adapter on slot(%s)\n",
slot_name(p_slot));
- mutex_unlock(&p_slot->ctrl->crit_sect);
return -ENODEV;
}
}
if (MRL_SENS(p_slot->ctrl)) {
- ret = p_slot->hpc_ops->get_latch_status(p_slot, &getstatus);
+ ret = pciehp_get_latch_status(p_slot, &getstatus);
if (ret || getstatus) {
ctrl_info(ctrl, "Latch open on slot(%s)\n",
slot_name(p_slot));
- mutex_unlock(&p_slot->ctrl->crit_sect);
return -ENODEV;
}
}
if (POWER_CTRL(p_slot->ctrl)) {
- ret = p_slot->hpc_ops->get_power_status(p_slot, &getstatus);
+ ret = pciehp_get_power_status(p_slot, &getstatus);
if (ret || !getstatus) {
ctrl_info(ctrl, "Already disabled on slot(%s)\n",
slot_name(p_slot));
- mutex_unlock(&p_slot->ctrl->crit_sect);
return -EINVAL;
}
}
ret = remove_board(p_slot);
update_slot_info(p_slot);
- mutex_unlock(&p_slot->ctrl->crit_sect);
return ret;
}
static inline int pciehp_readw(struct controller *ctrl, int reg, u16 *value)
{
- struct pci_dev *dev = ctrl->pci_dev;
+ struct pci_dev *dev = ctrl->pcie->port;
return pci_read_config_word(dev, ctrl->cap_base + reg, value);
}
static inline int pciehp_readl(struct controller *ctrl, int reg, u32 *value)
{
- struct pci_dev *dev = ctrl->pci_dev;
+ struct pci_dev *dev = ctrl->pcie->port;
return pci_read_config_dword(dev, ctrl->cap_base + reg, value);
}
static inline int pciehp_writew(struct controller *ctrl, int reg, u16 value)
{
- struct pci_dev *dev = ctrl->pci_dev;
+ struct pci_dev *dev = ctrl->pcie->port;
return pci_write_config_word(dev, ctrl->cap_base + reg, value);
}
static inline int pciehp_writel(struct controller *ctrl, int reg, u32 value)
{
- struct pci_dev *dev = ctrl->pci_dev;
+ struct pci_dev *dev = ctrl->pcie->port;
return pci_write_config_dword(dev, ctrl->cap_base + reg, value);
}
ctrl_dbg(ctrl, "Data Link Layer Link Active not set in 1000 msec\n");
}
-static int hpc_check_lnk_status(struct controller *ctrl)
+int pciehp_check_link_status(struct controller *ctrl)
{
u16 lnk_status;
int retval = 0;
return retval;
}
-static int hpc_get_attention_status(struct slot *slot, u8 *status)
+int pciehp_get_attention_status(struct slot *slot, u8 *status)
{
struct controller *ctrl = slot->ctrl;
u16 slot_ctrl;
return 0;
}
-static int hpc_get_power_status(struct slot *slot, u8 *status)
+int pciehp_get_power_status(struct slot *slot, u8 *status)
{
struct controller *ctrl = slot->ctrl;
u16 slot_ctrl;
return retval;
}
-static int hpc_get_latch_status(struct slot *slot, u8 *status)
+int pciehp_get_latch_status(struct slot *slot, u8 *status)
{
struct controller *ctrl = slot->ctrl;
u16 slot_status;
return 0;
}
-static int hpc_get_adapter_status(struct slot *slot, u8 *status)
+int pciehp_get_adapter_status(struct slot *slot, u8 *status)
{
struct controller *ctrl = slot->ctrl;
u16 slot_status;
return 0;
}
-static int hpc_query_power_fault(struct slot *slot)
+int pciehp_query_power_fault(struct slot *slot)
{
struct controller *ctrl = slot->ctrl;
u16 slot_status;
return !!(slot_status & PCI_EXP_SLTSTA_PFD);
}
-static int hpc_set_attention_status(struct slot *slot, u8 value)
+int pciehp_set_attention_status(struct slot *slot, u8 value)
{
struct controller *ctrl = slot->ctrl;
u16 slot_cmd;
return rc;
}
-static void hpc_set_green_led_on(struct slot *slot)
+void pciehp_green_led_on(struct slot *slot)
{
struct controller *ctrl = slot->ctrl;
u16 slot_cmd;
__func__, ctrl->cap_base + PCI_EXP_SLTCTL, slot_cmd);
}
-static void hpc_set_green_led_off(struct slot *slot)
+void pciehp_green_led_off(struct slot *slot)
{
struct controller *ctrl = slot->ctrl;
u16 slot_cmd;
__func__, ctrl->cap_base + PCI_EXP_SLTCTL, slot_cmd);
}
-static void hpc_set_green_led_blink(struct slot *slot)
+void pciehp_green_led_blink(struct slot *slot)
{
struct controller *ctrl = slot->ctrl;
u16 slot_cmd;
__func__, ctrl->cap_base + PCI_EXP_SLTCTL, slot_cmd);
}
-static int hpc_power_on_slot(struct slot * slot)
+int pciehp_power_on_slot(struct slot * slot)
{
struct controller *ctrl = slot->ctrl;
u16 slot_cmd;
u16 slot_status;
int retval = 0;
- ctrl_dbg(ctrl, "%s: slot->hp_slot %x\n", __func__, slot->hp_slot);
-
/* Clear sticky power-fault bit from previous power failures */
retval = pciehp_readw(ctrl, PCI_EXP_SLTSTA, &slot_status);
if (retval) {
static inline int pcie_mask_bad_dllp(struct controller *ctrl)
{
- struct pci_dev *dev = ctrl->pci_dev;
+ struct pci_dev *dev = ctrl->pcie->port;
int pos;
u32 reg;
static inline void pcie_unmask_bad_dllp(struct controller *ctrl)
{
- struct pci_dev *dev = ctrl->pci_dev;
+ struct pci_dev *dev = ctrl->pcie->port;
u32 reg;
int pos;
pci_write_config_dword(dev, pos + PCI_ERR_COR_MASK, reg);
}
-static int hpc_power_off_slot(struct slot * slot)
+int pciehp_power_off_slot(struct slot * slot)
{
struct controller *ctrl = slot->ctrl;
u16 slot_cmd;
int retval = 0;
int changed;
- ctrl_dbg(ctrl, "%s: slot->hp_slot %x\n", __func__, slot->hp_slot);
-
/*
* Set Bad DLLP Mask bit in Correctable Error Mask
* Register. This is the workaround against Bad DLLP error
static irqreturn_t pcie_isr(int irq, void *dev_id)
{
struct controller *ctrl = (struct controller *)dev_id;
+ struct slot *slot = ctrl->slot;
u16 detected, intr_loc;
- struct slot *p_slot;
/*
* In order to guarantee that all interrupt events are
if (!(intr_loc & ~PCI_EXP_SLTSTA_CC))
return IRQ_HANDLED;
- p_slot = pciehp_find_slot(ctrl, ctrl->slot_device_offset);
-
/* Check MRL Sensor Changed */
if (intr_loc & PCI_EXP_SLTSTA_MRLSC)
- pciehp_handle_switch_change(p_slot);
+ pciehp_handle_switch_change(slot);
/* Check Attention Button Pressed */
if (intr_loc & PCI_EXP_SLTSTA_ABP)
- pciehp_handle_attention_button(p_slot);
+ pciehp_handle_attention_button(slot);
/* Check Presence Detect Changed */
if (intr_loc & PCI_EXP_SLTSTA_PDC)
- pciehp_handle_presence_change(p_slot);
+ pciehp_handle_presence_change(slot);
/* Check Power Fault Detected */
if ((intr_loc & PCI_EXP_SLTSTA_PFD) && !ctrl->power_fault_detected) {
ctrl->power_fault_detected = 1;
- pciehp_handle_power_fault(p_slot);
+ pciehp_handle_power_fault(slot);
}
return IRQ_HANDLED;
}
-static int hpc_get_max_lnk_speed(struct slot *slot, enum pci_bus_speed *value)
+int pciehp_get_max_link_speed(struct slot *slot, enum pci_bus_speed *value)
{
struct controller *ctrl = slot->ctrl;
enum pcie_link_speed lnk_speed;
return retval;
}
-static int hpc_get_max_lnk_width(struct slot *slot,
+int pciehp_get_max_lnk_width(struct slot *slot,
enum pcie_link_width *value)
{
struct controller *ctrl = slot->ctrl;
return retval;
}
-static int hpc_get_cur_lnk_speed(struct slot *slot, enum pci_bus_speed *value)
+int pciehp_get_cur_link_speed(struct slot *slot, enum pci_bus_speed *value)
{
struct controller *ctrl = slot->ctrl;
enum pcie_link_speed lnk_speed = PCI_SPEED_UNKNOWN;
return retval;
}
-static int hpc_get_cur_lnk_width(struct slot *slot,
+int pciehp_get_cur_lnk_width(struct slot *slot,
enum pcie_link_width *value)
{
struct controller *ctrl = slot->ctrl;
return retval;
}
-static void pcie_release_ctrl(struct controller *ctrl);
-static struct hpc_ops pciehp_hpc_ops = {
- .power_on_slot = hpc_power_on_slot,
- .power_off_slot = hpc_power_off_slot,
- .set_attention_status = hpc_set_attention_status,
- .get_power_status = hpc_get_power_status,
- .get_attention_status = hpc_get_attention_status,
- .get_latch_status = hpc_get_latch_status,
- .get_adapter_status = hpc_get_adapter_status,
-
- .get_max_bus_speed = hpc_get_max_lnk_speed,
- .get_cur_bus_speed = hpc_get_cur_lnk_speed,
- .get_max_lnk_width = hpc_get_max_lnk_width,
- .get_cur_lnk_width = hpc_get_cur_lnk_width,
-
- .query_power_fault = hpc_query_power_fault,
- .green_led_on = hpc_set_green_led_on,
- .green_led_off = hpc_set_green_led_off,
- .green_led_blink = hpc_set_green_led_blink,
-
- .release_ctlr = pcie_release_ctrl,
- .check_lnk_status = hpc_check_lnk_status,
-};
-
int pcie_enable_notification(struct controller *ctrl)
{
u16 cmd, mask;
if (!slot)
return -ENOMEM;
- slot->hp_slot = 0;
slot->ctrl = ctrl;
- slot->bus = ctrl->pci_dev->subordinate->number;
- slot->device = ctrl->slot_device_offset + slot->hp_slot;
- slot->hpc_ops = ctrl->hpc_ops;
- slot->number = ctrl->first_slot;
mutex_init(&slot->lock);
INIT_DELAYED_WORK(&slot->work, pciehp_queue_pushbutton_work);
- list_add(&slot->slot_list, &ctrl->slot_list);
+ ctrl->slot = slot;
return 0;
}
static void pcie_cleanup_slot(struct controller *ctrl)
{
- struct slot *slot;
- slot = list_first_entry(&ctrl->slot_list, struct slot, slot_list);
- list_del(&slot->slot_list);
+ struct slot *slot = ctrl->slot;
cancel_delayed_work(&slot->work);
flush_scheduled_work();
flush_workqueue(pciehp_wq);
{
int i;
u16 reg16;
- struct pci_dev *pdev = ctrl->pci_dev;
+ struct pci_dev *pdev = ctrl->pcie->port;
if (!pciehp_debug)
return;
(unsigned long long)pci_resource_start(pdev, i));
}
ctrl_info(ctrl, "Slot Capabilities : 0x%08x\n", ctrl->slot_cap);
- ctrl_info(ctrl, " Physical Slot Number : %d\n", ctrl->first_slot);
+ ctrl_info(ctrl, " Physical Slot Number : %d\n", PSN(ctrl));
ctrl_info(ctrl, " Attention Button : %3s\n",
ATTN_BUTTN(ctrl) ? "yes" : "no");
ctrl_info(ctrl, " Power Controller : %3s\n",
dev_err(&dev->device, "%s: Out of memory\n", __func__);
goto abort;
}
- INIT_LIST_HEAD(&ctrl->slot_list);
-
ctrl->pcie = dev;
- ctrl->pci_dev = pdev;
ctrl->cap_base = pci_find_capability(pdev, PCI_CAP_ID_EXP);
if (!ctrl->cap_base) {
ctrl_err(ctrl, "Cannot find PCI Express capability\n");
}
ctrl->slot_cap = slot_cap;
- ctrl->first_slot = slot_cap >> 19;
- ctrl->slot_device_offset = 0;
- ctrl->num_slots = 1;
- ctrl->hpc_ops = &pciehp_hpc_ops;
- mutex_init(&ctrl->crit_sect);
mutex_init(&ctrl->ctrl_lock);
init_waitqueue_head(&ctrl->queue);
dbg_ctrl(ctrl);
return NULL;
}
-void pcie_release_ctrl(struct controller *ctrl)
+void pciehp_release_ctrl(struct controller *ctrl)
{
pcie_shutdown_notification(ctrl);
pcie_cleanup_slot(ctrl);
int pciehp_configure_device(struct slot *p_slot)
{
struct pci_dev *dev;
- struct pci_bus *parent = p_slot->ctrl->pci_dev->subordinate;
+ struct pci_bus *parent = p_slot->ctrl->pcie->port->subordinate;
int num, fn;
struct controller *ctrl = p_slot->ctrl;
- dev = pci_get_slot(parent, PCI_DEVFN(p_slot->device, 0));
+ dev = pci_get_slot(parent, PCI_DEVFN(0, 0));
if (dev) {
ctrl_err(ctrl, "Device %s already exists "
- "at %04x:%02x:%02x, cannot hot-add\n", pci_name(dev),
- pci_domain_nr(parent), p_slot->bus, p_slot->device);
+ "at %04x:%02x:00, cannot hot-add\n", pci_name(dev),
+ pci_domain_nr(parent), parent->number);
pci_dev_put(dev);
return -EINVAL;
}
- num = pci_scan_slot(parent, PCI_DEVFN(p_slot->device, 0));
+ num = pci_scan_slot(parent, PCI_DEVFN(0, 0));
if (num == 0) {
ctrl_err(ctrl, "No new device found\n");
return -ENODEV;
}
for (fn = 0; fn < 8; fn++) {
- dev = pci_get_slot(parent, PCI_DEVFN(p_slot->device, fn));
+ dev = pci_get_slot(parent, PCI_DEVFN(0, fn));
if (!dev)
continue;
if ((dev->class >> 16) == PCI_BASE_CLASS_DISPLAY) {
int j;
u8 bctl = 0;
u8 presence = 0;
- struct pci_bus *parent = p_slot->ctrl->pci_dev->subordinate;
+ struct pci_bus *parent = p_slot->ctrl->pcie->port->subordinate;
u16 command;
struct controller *ctrl = p_slot->ctrl;
- ctrl_dbg(ctrl, "%s: domain:bus:dev = %04x:%02x:%02x\n",
- __func__, pci_domain_nr(parent), p_slot->bus, p_slot->device);
- ret = p_slot->hpc_ops->get_adapter_status(p_slot, &presence);
+ ctrl_dbg(ctrl, "%s: domain:bus:dev = %04x:%02x:00\n",
+ __func__, pci_domain_nr(parent), parent->number);
+ ret = pciehp_get_adapter_status(p_slot, &presence);
if (ret)
presence = 0;
for (j = 0; j < 8; j++) {
- struct pci_dev* temp = pci_get_slot(parent,
- (p_slot->device << 3) | j);
+ struct pci_dev* temp = pci_get_slot(parent, PCI_DEVFN(0, j));
if (!temp)
continue;
if ((temp->class >> 16) == PCI_BASE_CLASS_DISPLAY) {
{
if (pcie_aer_disable)
return -ENXIO;
+ if (!pci_msi_enabled())
+ return -ENXIO;
return pcie_port_service_register(&aerdriver);
}
pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
pci_read_config_dword(pdev, pos + PCI_EXP_LNKCAP, ®32);
info->support = (reg32 & PCI_EXP_LNKCAP_ASPMS) >> 10;
- /* 00b and 10b are defined as "Reserved". */
- if (info->support == PCIE_LINK_STATE_L1)
- info->support = 0;
info->latency_encoding_l0s = (reg32 & PCI_EXP_LNKCAP_L0SEL) >> 12;
info->latency_encoding_l1 = (reg32 & PCI_EXP_LNKCAP_L1EL) >> 15;
pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, ®16);
tristate "Au1x00 pcmcia support"
depends on SOC_AU1X00 && PCMCIA
+config PCMCIA_BCM63XX
+ tristate "bcm63xx pcmcia support"
+ depends on BCM63XX && PCMCIA
+
config PCMCIA_SA1100
tristate "SA1100 support"
depends on ARM && ARCH_SA1100 && PCMCIA
obj-$(CONFIG_M32R_PCC) += m32r_pcc.o
obj-$(CONFIG_M32R_CFC) += m32r_cfc.o
obj-$(CONFIG_PCMCIA_AU1X00) += au1x00_ss.o
+obj-$(CONFIG_PCMCIA_BCM63XX) += bcm63xx_pcmcia.o
obj-$(CONFIG_PCMCIA_VRC4171) += vrc4171_card.o
obj-$(CONFIG_PCMCIA_VRC4173) += vrc4173_cardu.o
obj-$(CONFIG_OMAP_CF) += omap_cf.o
pxa2xx-obj-$(CONFIG_ARCH_VIPER) += pxa2xx_viper.o
pxa2xx-obj-$(CONFIG_TRIZEPS_PCMCIA) += pxa2xx_trizeps4.o
pxa2xx-obj-$(CONFIG_MACH_PALMTX) += pxa2xx_palmtx.o
+pxa2xx-obj-$(CONFIG_MACH_PALMTC) += pxa2xx_palmtc.o
pxa2xx-obj-$(CONFIG_MACH_PALMLD) += pxa2xx_palmld.o
pxa2xx-obj-$(CONFIG_MACH_E740) += pxa2xx_e740.o
pxa2xx-obj-$(CONFIG_MACH_STARGATE2) += pxa2xx_stargate2.o
struct at91_cf_socket *cf = platform_get_drvdata(pdev);
struct at91_cf_data *board = cf->board;
- pcmcia_socket_dev_suspend(&pdev->dev, mesg);
+ pcmcia_socket_dev_suspend(&pdev->dev);
if (device_may_wakeup(&pdev->dev)) {
enable_irq_wake(board->det_pin);
if (board->irq_pin)
static int au1x00_drv_pcmcia_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int au1x00_drv_pcmcia_resume(struct platform_device *dev)
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/timer.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/gpio.h>
+
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include "bcm63xx_pcmcia.h"
+
+#define PFX "bcm63xx_pcmcia: "
+
+#ifdef CONFIG_CARDBUS
+/* if cardbus is used, platform device needs reference to actual pci
+ * device */
+static struct pci_dev *bcm63xx_cb_dev;
+#endif
+
+/*
+ * read/write helper for pcmcia regs
+ */
+static inline u32 pcmcia_readl(struct bcm63xx_pcmcia_socket *skt, u32 off)
+{
+ return bcm_readl(skt->base + off);
+}
+
+static inline void pcmcia_writel(struct bcm63xx_pcmcia_socket *skt,
+ u32 val, u32 off)
+{
+ bcm_writel(val, skt->base + off);
+}
+
+/*
+ * This callback should (re-)initialise the socket, turn on status
+ * interrupts and PCMCIA bus, and wait for power to stabilise so that
+ * the card status signals report correctly.
+ *
+ * Hardware cannot do that.
+ */
+static int bcm63xx_pcmcia_sock_init(struct pcmcia_socket *sock)
+{
+ return 0;
+}
+
+/*
+ * This callback should remove power on the socket, disable IRQs from
+ * the card, turn off status interrupts, and disable the PCMCIA bus.
+ *
+ * Hardware cannot do that.
+ */
+static int bcm63xx_pcmcia_suspend(struct pcmcia_socket *sock)
+{
+ return 0;
+}
+
+/*
+ * Implements the set_socket() operation for the in-kernel PCMCIA
+ * service (formerly SS_SetSocket in Card Services). We more or
+ * less punt all of this work and let the kernel handle the details
+ * of power configuration, reset, &c. We also record the value of
+ * `state' in order to regurgitate it to the PCMCIA core later.
+ */
+static int bcm63xx_pcmcia_set_socket(struct pcmcia_socket *sock,
+ socket_state_t *state)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ unsigned long flags;
+ u32 val;
+
+ skt = sock->driver_data;
+
+ spin_lock_irqsave(&skt->lock, flags);
+
+ /* note: hardware cannot control socket power, so we will
+ * always report SS_POWERON */
+
+ /* apply socket reset */
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ if (state->flags & SS_RESET)
+ val |= PCMCIA_C1_RESET_MASK;
+ else
+ val &= ~PCMCIA_C1_RESET_MASK;
+
+ /* reverse reset logic for cardbus card */
+ if (skt->card_detected && (skt->card_type & CARD_CARDBUS))
+ val ^= PCMCIA_C1_RESET_MASK;
+
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* keep requested state for event reporting */
+ skt->requested_state = *state;
+
+ spin_unlock_irqrestore(&skt->lock, flags);
+
+ return 0;
+}
+
+/*
+ * identity cardtype from VS[12] input, CD[12] input while only VS2 is
+ * floating, and CD[12] input while only VS1 is floating
+ */
+enum {
+ IN_VS1 = (1 << 0),
+ IN_VS2 = (1 << 1),
+ IN_CD1_VS2H = (1 << 2),
+ IN_CD2_VS2H = (1 << 3),
+ IN_CD1_VS1H = (1 << 4),
+ IN_CD2_VS1H = (1 << 5),
+};
+
+static const u8 vscd_to_cardtype[] = {
+
+ /* VS1 float, VS2 float */
+ [IN_VS1 | IN_VS2] = (CARD_PCCARD | CARD_5V),
+
+ /* VS1 grounded, VS2 float */
+ [IN_VS2] = (CARD_PCCARD | CARD_5V | CARD_3V),
+
+ /* VS1 grounded, VS2 grounded */
+ [0] = (CARD_PCCARD | CARD_5V | CARD_3V | CARD_XV),
+
+ /* VS1 tied to CD1, VS2 float */
+ [IN_VS1 | IN_VS2 | IN_CD1_VS1H] = (CARD_CARDBUS | CARD_3V),
+
+ /* VS1 grounded, VS2 tied to CD2 */
+ [IN_VS2 | IN_CD2_VS2H] = (CARD_CARDBUS | CARD_3V | CARD_XV),
+
+ /* VS1 tied to CD2, VS2 grounded */
+ [IN_VS1 | IN_CD2_VS1H] = (CARD_CARDBUS | CARD_3V | CARD_XV | CARD_YV),
+
+ /* VS1 float, VS2 grounded */
+ [IN_VS1] = (CARD_PCCARD | CARD_XV),
+
+ /* VS1 float, VS2 tied to CD2 */
+ [IN_VS1 | IN_VS2 | IN_CD2_VS2H] = (CARD_CARDBUS | CARD_3V),
+
+ /* VS1 float, VS2 tied to CD1 */
+ [IN_VS1 | IN_VS2 | IN_CD1_VS2H] = (CARD_CARDBUS | CARD_XV | CARD_YV),
+
+ /* VS1 tied to CD2, VS2 float */
+ [IN_VS1 | IN_VS2 | IN_CD2_VS1H] = (CARD_CARDBUS | CARD_YV),
+
+ /* VS2 grounded, VS1 is tied to CD1, CD2 is grounded */
+ [IN_VS1 | IN_CD1_VS1H] = 0, /* ignore cardbay */
+};
+
+/*
+ * poll hardware to check card insertion status
+ */
+static unsigned int __get_socket_status(struct bcm63xx_pcmcia_socket *skt)
+{
+ unsigned int stat;
+ u32 val;
+
+ stat = 0;
+
+ /* check CD for card presence */
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+
+ if (!(val & PCMCIA_C1_CD1_MASK) && !(val & PCMCIA_C1_CD2_MASK))
+ stat |= SS_DETECT;
+
+ /* if new insertion, detect cardtype */
+ if ((stat & SS_DETECT) && !skt->card_detected) {
+ unsigned int stat = 0;
+
+ /* float VS1, float VS2 */
+ val |= PCMCIA_C1_VS1OE_MASK;
+ val |= PCMCIA_C1_VS2OE_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* wait for output to stabilize and read VS[12] */
+ udelay(10);
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ stat |= (val & PCMCIA_C1_VS1_MASK) ? IN_VS1 : 0;
+ stat |= (val & PCMCIA_C1_VS2_MASK) ? IN_VS2 : 0;
+
+ /* drive VS1 low, float VS2 */
+ val &= ~PCMCIA_C1_VS1OE_MASK;
+ val |= PCMCIA_C1_VS2OE_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* wait for output to stabilize and read CD[12] */
+ udelay(10);
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ stat |= (val & PCMCIA_C1_CD1_MASK) ? IN_CD1_VS2H : 0;
+ stat |= (val & PCMCIA_C1_CD2_MASK) ? IN_CD2_VS2H : 0;
+
+ /* float VS1, drive VS2 low */
+ val |= PCMCIA_C1_VS1OE_MASK;
+ val &= ~PCMCIA_C1_VS2OE_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /* wait for output to stabilize and read CD[12] */
+ udelay(10);
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ stat |= (val & PCMCIA_C1_CD1_MASK) ? IN_CD1_VS1H : 0;
+ stat |= (val & PCMCIA_C1_CD2_MASK) ? IN_CD2_VS1H : 0;
+
+ /* guess cardtype from all this */
+ skt->card_type = vscd_to_cardtype[stat];
+ if (!skt->card_type)
+ dev_err(&skt->socket.dev, "unsupported card type\n");
+
+ /* drive both VS pin to 0 again */
+ val &= ~(PCMCIA_C1_VS1OE_MASK | PCMCIA_C1_VS2OE_MASK);
+
+ /* enable correct logic */
+ val &= ~(PCMCIA_C1_EN_PCMCIA_MASK | PCMCIA_C1_EN_CARDBUS_MASK);
+ if (skt->card_type & CARD_PCCARD)
+ val |= PCMCIA_C1_EN_PCMCIA_MASK;
+ else
+ val |= PCMCIA_C1_EN_CARDBUS_MASK;
+
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+ }
+ skt->card_detected = (stat & SS_DETECT) ? 1 : 0;
+
+ /* report card type/voltage */
+ if (skt->card_type & CARD_CARDBUS)
+ stat |= SS_CARDBUS;
+ if (skt->card_type & CARD_3V)
+ stat |= SS_3VCARD;
+ if (skt->card_type & CARD_XV)
+ stat |= SS_XVCARD;
+ stat |= SS_POWERON;
+
+ if (gpio_get_value(skt->pd->ready_gpio))
+ stat |= SS_READY;
+
+ return stat;
+}
+
+/*
+ * core request to get current socket status
+ */
+static int bcm63xx_pcmcia_get_status(struct pcmcia_socket *sock,
+ unsigned int *status)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+
+ skt = sock->driver_data;
+
+ spin_lock_bh(&skt->lock);
+ *status = __get_socket_status(skt);
+ spin_unlock_bh(&skt->lock);
+
+ return 0;
+}
+
+/*
+ * socket polling timer callback
+ */
+static void bcm63xx_pcmcia_poll(unsigned long data)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ unsigned int stat, events;
+
+ skt = (struct bcm63xx_pcmcia_socket *)data;
+
+ spin_lock_bh(&skt->lock);
+
+ stat = __get_socket_status(skt);
+
+ /* keep only changed bits, and mask with required one from the
+ * core */
+ events = (stat ^ skt->old_status) & skt->requested_state.csc_mask;
+ skt->old_status = stat;
+ spin_unlock_bh(&skt->lock);
+
+ if (events)
+ pcmcia_parse_events(&skt->socket, events);
+
+ mod_timer(&skt->timer,
+ jiffies + msecs_to_jiffies(BCM63XX_PCMCIA_POLL_RATE));
+}
+
+static int bcm63xx_pcmcia_set_io_map(struct pcmcia_socket *sock,
+ struct pccard_io_map *map)
+{
+ /* this doesn't seem to be called by pcmcia layer if static
+ * mapping is used */
+ return 0;
+}
+
+static int bcm63xx_pcmcia_set_mem_map(struct pcmcia_socket *sock,
+ struct pccard_mem_map *map)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ struct resource *res;
+
+ skt = sock->driver_data;
+ if (map->flags & MAP_ATTRIB)
+ res = skt->attr_res;
+ else
+ res = skt->common_res;
+
+ map->static_start = res->start + map->card_start;
+ return 0;
+}
+
+static struct pccard_operations bcm63xx_pcmcia_operations = {
+ .init = bcm63xx_pcmcia_sock_init,
+ .suspend = bcm63xx_pcmcia_suspend,
+ .get_status = bcm63xx_pcmcia_get_status,
+ .set_socket = bcm63xx_pcmcia_set_socket,
+ .set_io_map = bcm63xx_pcmcia_set_io_map,
+ .set_mem_map = bcm63xx_pcmcia_set_mem_map,
+};
+
+/*
+ * register pcmcia socket to core
+ */
+static int __devinit bcm63xx_drv_pcmcia_probe(struct platform_device *pdev)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ struct pcmcia_socket *sock;
+ struct resource *res, *irq_res;
+ unsigned int regmem_size = 0, iomem_size = 0;
+ u32 val;
+ int ret;
+
+ skt = kzalloc(sizeof(*skt), GFP_KERNEL);
+ if (!skt)
+ return -ENOMEM;
+ spin_lock_init(&skt->lock);
+ sock = &skt->socket;
+ sock->driver_data = skt;
+
+ /* make sure we have all resources we need */
+ skt->common_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ skt->attr_res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ skt->pd = pdev->dev.platform_data;
+ if (!skt->common_res || !skt->attr_res || !irq_res || !skt->pd) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ /* remap pcmcia registers */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ regmem_size = resource_size(res);
+ if (!request_mem_region(res->start, regmem_size, "bcm63xx_pcmcia")) {
+ ret = -EINVAL;
+ goto err;
+ }
+ skt->reg_res = res;
+
+ skt->base = ioremap(res->start, regmem_size);
+ if (!skt->base) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ /* remap io registers */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+ iomem_size = resource_size(res);
+ skt->io_base = ioremap(res->start, iomem_size);
+ if (!skt->io_base) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ /* resources are static */
+ sock->resource_ops = &pccard_static_ops;
+ sock->ops = &bcm63xx_pcmcia_operations;
+ sock->owner = THIS_MODULE;
+ sock->dev.parent = &pdev->dev;
+ sock->features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
+ sock->io_offset = (unsigned long)skt->io_base;
+ sock->pci_irq = irq_res->start;
+
+#ifdef CONFIG_CARDBUS
+ sock->cb_dev = bcm63xx_cb_dev;
+ if (bcm63xx_cb_dev)
+ sock->features |= SS_CAP_CARDBUS;
+#endif
+
+ /* assume common & attribute memory have the same size */
+ sock->map_size = resource_size(skt->common_res);
+
+ /* initialize polling timer */
+ setup_timer(&skt->timer, bcm63xx_pcmcia_poll, (unsigned long)skt);
+
+ /* initialize pcmcia control register, drive VS[12] to 0,
+ * leave CB IDSEL to the old value since it is set by the PCI
+ * layer */
+ val = pcmcia_readl(skt, PCMCIA_C1_REG);
+ val &= PCMCIA_C1_CBIDSEL_MASK;
+ val |= PCMCIA_C1_EN_PCMCIA_GPIO_MASK;
+ pcmcia_writel(skt, val, PCMCIA_C1_REG);
+
+ /*
+ * Hardware has only one set of timings registers, not one for
+ * each memory access type, so we configure them for the
+ * slowest one: attribute memory.
+ */
+ val = PCMCIA_C2_DATA16_MASK;
+ val |= 10 << PCMCIA_C2_RWCOUNT_SHIFT;
+ val |= 6 << PCMCIA_C2_INACTIVE_SHIFT;
+ val |= 3 << PCMCIA_C2_SETUP_SHIFT;
+ val |= 3 << PCMCIA_C2_HOLD_SHIFT;
+ pcmcia_writel(skt, val, PCMCIA_C2_REG);
+
+ ret = pcmcia_register_socket(sock);
+ if (ret)
+ goto err;
+
+ /* start polling socket */
+ mod_timer(&skt->timer,
+ jiffies + msecs_to_jiffies(BCM63XX_PCMCIA_POLL_RATE));
+
+ platform_set_drvdata(pdev, skt);
+ return 0;
+
+err:
+ if (skt->io_base)
+ iounmap(skt->io_base);
+ if (skt->base)
+ iounmap(skt->base);
+ if (skt->reg_res)
+ release_mem_region(skt->reg_res->start, regmem_size);
+ kfree(skt);
+ return ret;
+}
+
+static int __devexit bcm63xx_drv_pcmcia_remove(struct platform_device *pdev)
+{
+ struct bcm63xx_pcmcia_socket *skt;
+ struct resource *res;
+
+ skt = platform_get_drvdata(pdev);
+ del_timer_sync(&skt->timer);
+ iounmap(skt->base);
+ iounmap(skt->io_base);
+ res = skt->reg_res;
+ release_mem_region(res->start, resource_size(res));
+ kfree(skt);
+ return 0;
+}
+
+struct platform_driver bcm63xx_pcmcia_driver = {
+ .probe = bcm63xx_drv_pcmcia_probe,
+ .remove = __devexit_p(bcm63xx_drv_pcmcia_remove),
+ .driver = {
+ .name = "bcm63xx_pcmcia",
+ .owner = THIS_MODULE,
+ },
+};
+
+#ifdef CONFIG_CARDBUS
+static int __devinit bcm63xx_cb_probe(struct pci_dev *dev,
+ const struct pci_device_id *id)
+{
+ /* keep pci device */
+ bcm63xx_cb_dev = dev;
+ return platform_driver_register(&bcm63xx_pcmcia_driver);
+}
+
+static void __devexit bcm63xx_cb_exit(struct pci_dev *dev)
+{
+ platform_driver_unregister(&bcm63xx_pcmcia_driver);
+ bcm63xx_cb_dev = NULL;
+}
+
+static struct pci_device_id bcm63xx_cb_table[] = {
+ {
+ .vendor = PCI_VENDOR_ID_BROADCOM,
+ .device = BCM6348_CPU_ID,
+ .subvendor = PCI_VENDOR_ID_BROADCOM,
+ .subdevice = PCI_ANY_ID,
+ .class = PCI_CLASS_BRIDGE_CARDBUS << 8,
+ .class_mask = ~0,
+ },
+
+ {
+ .vendor = PCI_VENDOR_ID_BROADCOM,
+ .device = BCM6358_CPU_ID,
+ .subvendor = PCI_VENDOR_ID_BROADCOM,
+ .subdevice = PCI_ANY_ID,
+ .class = PCI_CLASS_BRIDGE_CARDBUS << 8,
+ .class_mask = ~0,
+ },
+
+ { },
+};
+
+MODULE_DEVICE_TABLE(pci, bcm63xx_cb_table);
+
+static struct pci_driver bcm63xx_cardbus_driver = {
+ .name = "bcm63xx_cardbus",
+ .id_table = bcm63xx_cb_table,
+ .probe = bcm63xx_cb_probe,
+ .remove = __devexit_p(bcm63xx_cb_exit),
+};
+#endif
+
+/*
+ * if cardbus support is enabled, register our platform device after
+ * our fake cardbus bridge has been registered
+ */
+static int __init bcm63xx_pcmcia_init(void)
+{
+#ifdef CONFIG_CARDBUS
+ return pci_register_driver(&bcm63xx_cardbus_driver);
+#else
+ return platform_driver_register(&bcm63xx_pcmcia_driver);
+#endif
+}
+
+static void __exit bcm63xx_pcmcia_exit(void)
+{
+#ifdef CONFIG_CARDBUS
+ return pci_unregister_driver(&bcm63xx_cardbus_driver);
+#else
+ platform_driver_unregister(&bcm63xx_pcmcia_driver);
+#endif
+}
+
+module_init(bcm63xx_pcmcia_init);
+module_exit(bcm63xx_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
+MODULE_DESCRIPTION("Linux PCMCIA Card Services: bcm63xx Socket Controller");
--- /dev/null
+#ifndef BCM63XX_PCMCIA_H_
+#define BCM63XX_PCMCIA_H_
+
+#include <linux/types.h>
+#include <linux/timer.h>
+#include <pcmcia/ss.h>
+#include <bcm63xx_dev_pcmcia.h>
+
+/* socket polling rate in ms */
+#define BCM63XX_PCMCIA_POLL_RATE 500
+
+enum {
+ CARD_CARDBUS = (1 << 0),
+ CARD_PCCARD = (1 << 1),
+ CARD_5V = (1 << 2),
+ CARD_3V = (1 << 3),
+ CARD_XV = (1 << 4),
+ CARD_YV = (1 << 5),
+};
+
+struct bcm63xx_pcmcia_socket {
+ struct pcmcia_socket socket;
+
+ /* platform specific data */
+ struct bcm63xx_pcmcia_platform_data *pd;
+
+ /* all regs access are protected by this spinlock */
+ spinlock_t lock;
+
+ /* pcmcia registers resource */
+ struct resource *reg_res;
+
+ /* base remapped address of registers */
+ void __iomem *base;
+
+ /* whether a card is detected at the moment */
+ int card_detected;
+
+ /* type of detected card (mask of above enum) */
+ u8 card_type;
+
+ /* keep last socket status to implement event reporting */
+ unsigned int old_status;
+
+ /* backup of requested socket state */
+ socket_state_t requested_state;
+
+ /* timer used for socket status polling */
+ struct timer_list timer;
+
+ /* attribute/common memory resources */
+ struct resource *attr_res;
+ struct resource *common_res;
+ struct resource *io_res;
+
+ /* base address of io memory */
+ void __iomem *io_base;
+};
+
+#endif /* BCM63XX_PCMCIA_H_ */
static int bfin_cf_suspend(struct platform_device *pdev, pm_message_t mesg)
{
- return pcmcia_socket_dev_suspend(&pdev->dev, mesg);
+ return pcmcia_socket_dev_suspend(&pdev->dev);
}
static int bfin_cf_resume(struct platform_device *pdev)
static int socket_resume(struct pcmcia_socket *skt);
static int socket_suspend(struct pcmcia_socket *skt);
-int pcmcia_socket_dev_suspend(struct device *dev, pm_message_t state)
+int pcmcia_socket_dev_suspend(struct device *dev)
{
struct pcmcia_socket *socket;
#ifdef CONFIG_PM
static int i82092aa_socket_suspend (struct pci_dev *dev, pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int i82092aa_socket_resume (struct pci_dev *dev)
static int i82365_drv_pcmcia_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int i82365_drv_pcmcia_resume(struct platform_device *dev)
static int cfc_drv_pcmcia_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int cfc_drv_pcmcia_resume(struct platform_device *dev)
static int pcc_drv_pcmcia_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int pcc_drv_pcmcia_resume(struct platform_device *dev)
#ifdef CONFIG_PM
static int m8xx_suspend(struct platform_device *pdev, pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&pdev->dev, state);
+ return pcmcia_socket_dev_suspend(&pdev->dev);
}
static int m8xx_resume(struct platform_device *pdev)
static int omap_cf_suspend(struct platform_device *pdev, pm_message_t mesg)
{
- return pcmcia_socket_dev_suspend(&pdev->dev, mesg);
+ return pcmcia_socket_dev_suspend(&pdev->dev);
}
static int omap_cf_resume(struct platform_device *pdev)
#ifdef CONFIG_PM
static int pd6729_socket_suspend(struct pci_dev *dev, pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int pd6729_socket_resume(struct pci_dev *dev)
return soc_common_drv_pcmcia_remove(&dev->dev);
}
-static int pxa2xx_drv_pcmcia_suspend(struct platform_device *dev, pm_message_t state)
+static int pxa2xx_drv_pcmcia_suspend(struct device *dev)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(dev);
}
-static int pxa2xx_drv_pcmcia_resume(struct platform_device *dev)
+static int pxa2xx_drv_pcmcia_resume(struct device *dev)
{
- pxa2xx_configure_sockets(&dev->dev);
- return pcmcia_socket_dev_resume(&dev->dev);
+ pxa2xx_configure_sockets(dev);
+ return pcmcia_socket_dev_resume(dev);
}
+static struct dev_pm_ops pxa2xx_drv_pcmcia_pm_ops = {
+ .suspend = pxa2xx_drv_pcmcia_suspend,
+ .resume = pxa2xx_drv_pcmcia_resume,
+};
+
static struct platform_driver pxa2xx_pcmcia_driver = {
.probe = pxa2xx_drv_pcmcia_probe,
.remove = pxa2xx_drv_pcmcia_remove,
- .suspend = pxa2xx_drv_pcmcia_suspend,
- .resume = pxa2xx_drv_pcmcia_resume,
.driver = {
.name = "pxa2xx-pcmcia",
.owner = THIS_MODULE,
+ .pm = &pxa2xx_drv_pcmcia_pm_ops,
},
};
--- /dev/null
+/*
+ * linux/drivers/pcmcia/pxa2xx_palmtc.c
+ *
+ * Driver for Palm Tungsten|C PCMCIA
+ *
+ * Copyright (C) 2008 Alex Osborne <ato@meshy.org>
+ * Copyright (C) 2009 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+
+#include <asm/mach-types.h>
+#include <mach/palmtc.h>
+#include "soc_common.h"
+
+static int palmtc_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+ int ret;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_POWER1, "PCMCIA PWR1");
+ if (ret)
+ goto err1;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_POWER1, 0);
+ if (ret)
+ goto err2;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_POWER2, "PCMCIA PWR2");
+ if (ret)
+ goto err2;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_POWER2, 0);
+ if (ret)
+ goto err3;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_POWER3, "PCMCIA PWR3");
+ if (ret)
+ goto err3;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_POWER3, 0);
+ if (ret)
+ goto err4;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_RESET, "PCMCIA RST");
+ if (ret)
+ goto err4;
+ ret = gpio_direction_output(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+ if (ret)
+ goto err5;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_READY, "PCMCIA RDY");
+ if (ret)
+ goto err5;
+ ret = gpio_direction_input(GPIO_NR_PALMTC_PCMCIA_READY);
+ if (ret)
+ goto err6;
+
+ ret = gpio_request(GPIO_NR_PALMTC_PCMCIA_PWRREADY, "PCMCIA PWRRDY");
+ if (ret)
+ goto err6;
+ ret = gpio_direction_input(GPIO_NR_PALMTC_PCMCIA_PWRREADY);
+ if (ret)
+ goto err7;
+
+ skt->irq = IRQ_GPIO(GPIO_NR_PALMTC_PCMCIA_READY);
+ return 0;
+
+err7:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_PWRREADY);
+err6:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_READY);
+err5:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_RESET);
+err4:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER3);
+err3:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER2);
+err2:
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER1);
+err1:
+ return ret;
+}
+
+static void palmtc_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_PWRREADY);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_READY);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_RESET);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER3);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER2);
+ gpio_free(GPIO_NR_PALMTC_PCMCIA_POWER1);
+}
+
+static void palmtc_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+ struct pcmcia_state *state)
+{
+ state->detect = 1; /* always inserted */
+ state->ready = !!gpio_get_value(GPIO_NR_PALMTC_PCMCIA_READY);
+ state->bvd1 = 1;
+ state->bvd2 = 1;
+ state->wrprot = 0;
+ state->vs_3v = 1;
+ state->vs_Xv = 0;
+}
+
+static int palmtc_wifi_powerdown(void)
+{
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER2, 0);
+ mdelay(40);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER1, 0);
+ return 0;
+}
+
+static int palmtc_wifi_powerup(void)
+{
+ int timeout = 50;
+
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER3, 1);
+ mdelay(50);
+
+ /* Power up the card, 1.8V first, after a while 3.3V */
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER1, 1);
+ mdelay(100);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER2, 1);
+
+ /* Wait till the card is ready */
+ while (!gpio_get_value(GPIO_NR_PALMTC_PCMCIA_PWRREADY) &&
+ timeout) {
+ mdelay(1);
+ timeout--;
+ }
+
+ /* Power down the WiFi in case of error */
+ if (!timeout) {
+ palmtc_wifi_powerdown();
+ return 1;
+ }
+
+ /* Reset the card */
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+ mdelay(20);
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 0);
+ mdelay(25);
+
+ gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER3, 0);
+
+ return 0;
+}
+
+static int palmtc_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+ const socket_state_t *state)
+{
+ int ret = 1;
+
+ if (state->Vcc == 0)
+ ret = palmtc_wifi_powerdown();
+ else if (state->Vcc == 33)
+ ret = palmtc_wifi_powerup();
+
+ return ret;
+}
+
+static void palmtc_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
+{
+}
+
+static void palmtc_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
+{
+}
+
+static struct pcmcia_low_level palmtc_pcmcia_ops = {
+ .owner = THIS_MODULE,
+
+ .first = 0,
+ .nr = 1,
+
+ .hw_init = palmtc_pcmcia_hw_init,
+ .hw_shutdown = palmtc_pcmcia_hw_shutdown,
+
+ .socket_state = palmtc_pcmcia_socket_state,
+ .configure_socket = palmtc_pcmcia_configure_socket,
+
+ .socket_init = palmtc_pcmcia_socket_init,
+ .socket_suspend = palmtc_pcmcia_socket_suspend,
+};
+
+static struct platform_device *palmtc_pcmcia_device;
+
+static int __init palmtc_pcmcia_init(void)
+{
+ int ret;
+
+ if (!machine_is_palmtc())
+ return -ENODEV;
+
+ palmtc_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+ if (!palmtc_pcmcia_device)
+ return -ENOMEM;
+
+ ret = platform_device_add_data(palmtc_pcmcia_device, &palmtc_pcmcia_ops,
+ sizeof(palmtc_pcmcia_ops));
+
+ if (!ret)
+ ret = platform_device_add(palmtc_pcmcia_device);
+
+ if (ret)
+ platform_device_put(palmtc_pcmcia_device);
+
+ return ret;
+}
+
+static void __exit palmtc_pcmcia_exit(void)
+{
+ platform_device_unregister(palmtc_pcmcia_device);
+}
+
+module_init(palmtc_pcmcia_init);
+module_exit(palmtc_pcmcia_exit);
+
+MODULE_AUTHOR("Alex Osborne <ato@meshy.org>,"
+ " Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Palm Tungsten|C");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
.socket_suspend = assabet_pcmcia_socket_suspend,
};
-int __init pcmcia_assabet_init(struct device *dev)
+int pcmcia_assabet_init(struct device *dev)
{
int ret = -ENODEV;
static int sa11x0_drv_pcmcia_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int sa11x0_drv_pcmcia_resume(struct platform_device *dev)
.socket_suspend = sa1111_pcmcia_socket_suspend,
};
-int __init pcmcia_neponset_init(struct sa1111_dev *sadev)
+int pcmcia_neponset_init(struct sa1111_dev *sadev)
{
int ret = -ENODEV;
static int pcmcia_suspend(struct sa1111_dev *dev, pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int pcmcia_resume(struct sa1111_dev *dev)
static int tcic_drv_pcmcia_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int tcic_drv_pcmcia_resume(struct platform_device *dev)
static int vrc4171_card_suspend(struct platform_device *dev,
pm_message_t state)
{
- return pcmcia_socket_dev_suspend(&dev->dev, state);
+ return pcmcia_socket_dev_suspend(&dev->dev);
}
static int vrc4171_card_resume(struct platform_device *dev)
}
#ifdef CONFIG_PM
-static int yenta_dev_suspend (struct pci_dev *dev, pm_message_t state)
+static int yenta_dev_suspend_noirq(struct device *dev)
{
- struct yenta_socket *socket = pci_get_drvdata(dev);
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct yenta_socket *socket = pci_get_drvdata(pdev);
int ret;
- ret = pcmcia_socket_dev_suspend(&dev->dev, state);
+ ret = pcmcia_socket_dev_suspend(dev);
- if (socket) {
- if (socket->type && socket->type->save_state)
- socket->type->save_state(socket);
+ if (!socket)
+ return ret;
- /* FIXME: pci_save_state needs to have a better interface */
- pci_save_state(dev);
- pci_read_config_dword(dev, 16*4, &socket->saved_state[0]);
- pci_read_config_dword(dev, 17*4, &socket->saved_state[1]);
- pci_disable_device(dev);
+ if (socket->type && socket->type->save_state)
+ socket->type->save_state(socket);
- /*
- * Some laptops (IBM T22) do not like us putting the Cardbus
- * bridge into D3. At a guess, some other laptop will
- * probably require this, so leave it commented out for now.
- */
- /* pci_set_power_state(dev, 3); */
- }
+ pci_save_state(pdev);
+ pci_read_config_dword(pdev, 16*4, &socket->saved_state[0]);
+ pci_read_config_dword(pdev, 17*4, &socket->saved_state[1]);
+ pci_disable_device(pdev);
+
+ /*
+ * Some laptops (IBM T22) do not like us putting the Cardbus
+ * bridge into D3. At a guess, some other laptop will
+ * probably require this, so leave it commented out for now.
+ */
+ /* pci_set_power_state(dev, 3); */
return ret;
}
-
-static int yenta_dev_resume (struct pci_dev *dev)
+static int yenta_dev_resume_noirq(struct device *dev)
{
- struct yenta_socket *socket = pci_get_drvdata(dev);
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct yenta_socket *socket = pci_get_drvdata(pdev);
+ int ret;
- if (socket) {
- int rc;
+ if (!socket)
+ return 0;
- pci_set_power_state(dev, 0);
- /* FIXME: pci_restore_state needs to have a better interface */
- pci_restore_state(dev);
- pci_write_config_dword(dev, 16*4, socket->saved_state[0]);
- pci_write_config_dword(dev, 17*4, socket->saved_state[1]);
+ pci_write_config_dword(pdev, 16*4, socket->saved_state[0]);
+ pci_write_config_dword(pdev, 17*4, socket->saved_state[1]);
- rc = pci_enable_device(dev);
- if (rc)
- return rc;
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
- pci_set_master(dev);
+ pci_set_master(pdev);
- if (socket->type && socket->type->restore_state)
- socket->type->restore_state(socket);
- }
+ if (socket->type && socket->type->restore_state)
+ socket->type->restore_state(socket);
- return pcmcia_socket_dev_resume(&dev->dev);
+ return pcmcia_socket_dev_resume(dev);
}
+
+static struct dev_pm_ops yenta_pm_ops = {
+ .suspend_noirq = yenta_dev_suspend_noirq,
+ .resume_noirq = yenta_dev_resume_noirq,
+ .freeze_noirq = yenta_dev_suspend_noirq,
+ .thaw_noirq = yenta_dev_resume_noirq,
+ .poweroff_noirq = yenta_dev_suspend_noirq,
+ .restore_noirq = yenta_dev_resume_noirq,
+};
+
+#define YENTA_PM_OPS (¥ta_pm_ops)
+#else
+#define YENTA_PM_OPS NULL
#endif
#define CB_ID(vend,dev,type) \
.id_table = yenta_table,
.probe = yenta_probe,
.remove = __devexit_p(yenta_close),
-#ifdef CONFIG_PM
- .suspend = yenta_dev_suspend,
- .resume = yenta_dev_resume,
-#endif
+ .driver.pm = YENTA_PM_OPS,
};
struct backlight_device *bd = eeepc_backlight_device;
if (bd) {
int old = bd->props.brightness;
- bd->props.brightness = read_brightness(bd);
+ backlight_force_update(bd, BACKLIGHT_UPDATE_HOTKEY);
return old;
}
return -1;
sony_backlight_update_status(sony_backlight_device) < 0)
printk(KERN_WARNING DRV_PFX "unable to restore brightness level\n");
+ /* re-read rfkill state */
+ sony_nc_rfkill_update();
+
return 0;
}
struct rfkill *rfk;
enum rfkill_type type;
const char *name;
+ int result;
+ bool hwblock;
switch (nc_type) {
case SONY_WIFI:
if (!rfk)
return -ENOMEM;
+ sony_call_snc_handle(0x124, 0x200, &result);
+ hwblock = !(result & 0x1);
+ rfkill_set_hw_state(rfk, hwblock);
+
err = rfkill_register(rfk);
if (err) {
rfkill_destroy(rfk);
}
}
- /* try to _INI the device if such method exists (ACPI spec 3.0-6.5.1
- * should be respected as we already checked for the device presence above */
- if (ACPI_SUCCESS(acpi_get_handle(sony_nc_acpi_handle, METHOD_NAME__INI, &handle))) {
- dprintk("Invoking _INI\n");
- if (ACPI_FAILURE(acpi_evaluate_object(sony_nc_acpi_handle, METHOD_NAME__INI,
- NULL, NULL)))
- dprintk("_INI Method failed\n");
- }
-
if (ACPI_SUCCESS(acpi_get_handle(sony_nc_acpi_handle, "ECON",
&handle))) {
if (acpi_callsetfunc(sony_nc_acpi_handle, "ECON", 1, NULL))
struct sonypi_event *events;
};
-struct device_ctrl {
+struct sony_pic_dev {
+ struct acpi_device *acpi_dev;
+ struct sony_pic_irq *cur_irq;
+ struct sony_pic_ioport *cur_ioport;
+ struct list_head interrupts;
+ struct list_head ioports;
+ struct mutex lock;
+ struct sonypi_eventtypes *event_types;
+ int (*handle_irq)(const u8, const u8);
int model;
- int (*handle_irq)(const u8, const u8);
u16 evport_offset;
- u8 has_camera;
- u8 has_bluetooth;
- u8 has_wwan;
- struct sonypi_eventtypes *event_types;
-};
-
-struct sony_pic_dev {
- struct device_ctrl *control;
- struct acpi_device *acpi_dev;
- struct sony_pic_irq *cur_irq;
- struct sony_pic_ioport *cur_ioport;
- struct list_head interrupts;
- struct list_head ioports;
- struct mutex lock;
- u8 camera_power;
- u8 bluetooth_power;
- u8 wwan_power;
+ u8 camera_power;
+ u8 bluetooth_power;
+ u8 wwan_power;
};
static struct sony_pic_dev spic_dev = {
.ioports = LIST_HEAD_INIT(spic_dev.ioports),
};
+static int spic_drv_registered;
+
/* Event masks */
#define SONYPI_JOGGER_MASK 0x00000001
#define SONYPI_CAPTURE_MASK 0x00000002
return 1;
}
-static struct device_ctrl spic_types[] = {
- {
- .model = SONYPI_DEVICE_TYPE1,
- .handle_irq = NULL,
- .evport_offset = SONYPI_TYPE1_OFFSET,
- .event_types = type1_events,
- },
- {
- .model = SONYPI_DEVICE_TYPE2,
- .handle_irq = NULL,
- .evport_offset = SONYPI_TYPE2_OFFSET,
- .event_types = type2_events,
- },
- {
- .model = SONYPI_DEVICE_TYPE3,
- .handle_irq = type3_handle_irq,
- .evport_offset = SONYPI_TYPE3_OFFSET,
- .event_types = type3_events,
- },
-};
-
static void sony_pic_detect_device_type(struct sony_pic_dev *dev)
{
struct pci_dev *pcidev;
pcidev = pci_get_device(PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_82371AB_3, NULL);
if (pcidev) {
- dev->control = &spic_types[0];
+ dev->model = SONYPI_DEVICE_TYPE1;
+ dev->evport_offset = SONYPI_TYPE1_OFFSET;
+ dev->event_types = type1_events;
goto out;
}
pcidev = pci_get_device(PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_ICH6_1, NULL);
if (pcidev) {
- dev->control = &spic_types[2];
+ dev->model = SONYPI_DEVICE_TYPE2;
+ dev->evport_offset = SONYPI_TYPE2_OFFSET;
+ dev->event_types = type2_events;
goto out;
}
pcidev = pci_get_device(PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_ICH7_1, NULL);
if (pcidev) {
- dev->control = &spic_types[2];
+ dev->model = SONYPI_DEVICE_TYPE3;
+ dev->handle_irq = type3_handle_irq;
+ dev->evport_offset = SONYPI_TYPE3_OFFSET;
+ dev->event_types = type3_events;
goto out;
}
pcidev = pci_get_device(PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_ICH8_4, NULL);
if (pcidev) {
- dev->control = &spic_types[2];
+ dev->model = SONYPI_DEVICE_TYPE3;
+ dev->handle_irq = type3_handle_irq;
+ dev->evport_offset = SONYPI_TYPE3_OFFSET;
+ dev->event_types = type3_events;
goto out;
}
pcidev = pci_get_device(PCI_VENDOR_ID_INTEL,
PCI_DEVICE_ID_INTEL_ICH9_1, NULL);
if (pcidev) {
- dev->control = &spic_types[2];
+ dev->model = SONYPI_DEVICE_TYPE3;
+ dev->handle_irq = type3_handle_irq;
+ dev->evport_offset = SONYPI_TYPE3_OFFSET;
+ dev->event_types = type3_events;
goto out;
}
/* default */
- dev->control = &spic_types[1];
+ dev->model = SONYPI_DEVICE_TYPE2;
+ dev->evport_offset = SONYPI_TYPE2_OFFSET;
+ dev->event_types = type2_events;
out:
if (pcidev)
pci_dev_put(pcidev);
printk(KERN_INFO DRV_PFX "detected Type%d model\n",
- dev->control->model == SONYPI_DEVICE_TYPE1 ? 1 :
- dev->control->model == SONYPI_DEVICE_TYPE2 ? 2 : 3);
+ dev->model == SONYPI_DEVICE_TYPE1 ? 1 :
+ dev->model == SONYPI_DEVICE_TYPE2 ? 2 : 3);
}
/* camera tests and poweron/poweroff */
buffer.pointer = resource;
/* setup Type 1 resources */
- if (spic_dev.control->model == SONYPI_DEVICE_TYPE1) {
+ if (spic_dev.model == SONYPI_DEVICE_TYPE1) {
/* setup io resources */
resource->res1.type = ACPI_RESOURCE_TYPE_IO;
data_mask = inb_p(dev->cur_ioport->io2.minimum);
else
data_mask = inb_p(dev->cur_ioport->io1.minimum +
- dev->control->evport_offset);
+ dev->evport_offset);
dprintk("event ([%.2x] [%.2x]) at port 0x%.4x(+0x%.2x)\n",
ev, data_mask, dev->cur_ioport->io1.minimum,
- dev->control->evport_offset);
+ dev->evport_offset);
if (ev == 0x00 || ev == 0xff)
return IRQ_HANDLED;
- for (i = 0; dev->control->event_types[i].mask; i++) {
+ for (i = 0; dev->event_types[i].mask; i++) {
- if ((data_mask & dev->control->event_types[i].data) !=
- dev->control->event_types[i].data)
+ if ((data_mask & dev->event_types[i].data) !=
+ dev->event_types[i].data)
continue;
- if (!(mask & dev->control->event_types[i].mask))
+ if (!(mask & dev->event_types[i].mask))
continue;
- for (j = 0; dev->control->event_types[i].events[j].event; j++) {
- if (ev == dev->control->event_types[i].events[j].data) {
+ for (j = 0; dev->event_types[i].events[j].event; j++) {
+ if (ev == dev->event_types[i].events[j].data) {
device_event =
- dev->control->
- event_types[i].events[j].event;
+ dev->event_types[i].events[j].event;
goto found;
}
}
/* Still not able to decode the event try to pass
* it over to the minidriver
*/
- if (dev->control->handle_irq &&
- dev->control->handle_irq(data_mask, ev) == 0)
+ if (dev->handle_irq && dev->handle_irq(data_mask, ev) == 0)
return IRQ_HANDLED;
dprintk("unknown event ([%.2x] [%.2x]) at port 0x%.4x(+0x%.2x)\n",
ev, data_mask, dev->cur_ioport->io1.minimum,
- dev->control->evport_offset);
+ dev->evport_offset);
return IRQ_HANDLED;
found:
/* request IRQ */
list_for_each_entry_reverse(irq, &spic_dev.interrupts, list) {
if (!request_irq(irq->irq.interrupts[0], sony_pic_irq,
- IRQF_SHARED, "sony-laptop", &spic_dev)) {
+ IRQF_DISABLED, "sony-laptop", &spic_dev)) {
dprintk("IRQ: %d - triggering: %d - "
"polarity: %d - shr: %d\n",
irq->irq.interrupts[0],
"Unable to register SPIC driver.");
goto out;
}
+ spic_drv_registered = 1;
}
result = acpi_bus_register_driver(&sony_nc_driver);
return 0;
out_unregister_pic:
- if (!no_spic)
+ if (spic_drv_registered)
acpi_bus_unregister_driver(&sony_pic_driver);
out:
return result;
static void __exit sony_laptop_exit(void)
{
acpi_bus_unregister_driver(&sony_nc_driver);
- if (!no_spic)
+ if (spic_drv_registered)
acpi_bus_unregister_driver(&sony_pic_driver);
}
*/
#define TPACPI_VERSION "0.23"
-#define TPACPI_SYSFS_VERSION 0x020400
+#define TPACPI_SYSFS_VERSION 0x020500
/*
* Changelog:
TP_ACPI_WGSV_STATE_UWBPWR = 0x0020, /* UWB radio enabled */
};
+/* HKEY events */
+enum tpacpi_hkey_event_t {
+ /* Hotkey-related */
+ TP_HKEY_EV_HOTKEY_BASE = 0x1001, /* first hotkey (FN+F1) */
+ TP_HKEY_EV_BRGHT_UP = 0x1010, /* Brightness up */
+ TP_HKEY_EV_BRGHT_DOWN = 0x1011, /* Brightness down */
+ TP_HKEY_EV_VOL_UP = 0x1015, /* Volume up or unmute */
+ TP_HKEY_EV_VOL_DOWN = 0x1016, /* Volume down or unmute */
+ TP_HKEY_EV_VOL_MUTE = 0x1017, /* Mixer output mute */
+
+ /* Reasons for waking up from S3/S4 */
+ TP_HKEY_EV_WKUP_S3_UNDOCK = 0x2304, /* undock requested, S3 */
+ TP_HKEY_EV_WKUP_S4_UNDOCK = 0x2404, /* undock requested, S4 */
+ TP_HKEY_EV_WKUP_S3_BAYEJ = 0x2305, /* bay ejection req, S3 */
+ TP_HKEY_EV_WKUP_S4_BAYEJ = 0x2405, /* bay ejection req, S4 */
+ TP_HKEY_EV_WKUP_S3_BATLOW = 0x2313, /* battery empty, S3 */
+ TP_HKEY_EV_WKUP_S4_BATLOW = 0x2413, /* battery empty, S4 */
+
+ /* Auto-sleep after eject request */
+ TP_HKEY_EV_BAYEJ_ACK = 0x3003, /* bay ejection complete */
+ TP_HKEY_EV_UNDOCK_ACK = 0x4003, /* undock complete */
+
+ /* Misc bay events */
+ TP_HKEY_EV_OPTDRV_EJ = 0x3006, /* opt. drive tray ejected */
+
+ /* User-interface events */
+ TP_HKEY_EV_LID_CLOSE = 0x5001, /* laptop lid closed */
+ TP_HKEY_EV_LID_OPEN = 0x5002, /* laptop lid opened */
+ TP_HKEY_EV_TABLET_TABLET = 0x5009, /* tablet swivel up */
+ TP_HKEY_EV_TABLET_NOTEBOOK = 0x500a, /* tablet swivel down */
+ TP_HKEY_EV_PEN_INSERTED = 0x500b, /* tablet pen inserted */
+ TP_HKEY_EV_PEN_REMOVED = 0x500c, /* tablet pen removed */
+ TP_HKEY_EV_BRGHT_CHANGED = 0x5010, /* backlight control event */
+
+ /* Thermal events */
+ TP_HKEY_EV_ALARM_BAT_HOT = 0x6011, /* battery too hot */
+ TP_HKEY_EV_ALARM_BAT_XHOT = 0x6012, /* battery critically hot */
+ TP_HKEY_EV_ALARM_SENSOR_HOT = 0x6021, /* sensor too hot */
+ TP_HKEY_EV_ALARM_SENSOR_XHOT = 0x6022, /* sensor critically hot */
+ TP_HKEY_EV_THM_TABLE_CHANGED = 0x6030, /* thermal table changed */
+
+ /* Misc */
+ TP_HKEY_EV_RFKILL_CHANGED = 0x7000, /* rfkill switch changed */
+};
+
/****************************************************************************
* Main driver
*/
* Hotkey subdriver
*/
+/*
+ * ThinkPad firmware event model
+ *
+ * The ThinkPad firmware has two main event interfaces: normal ACPI
+ * notifications (which follow the ACPI standard), and a private event
+ * interface.
+ *
+ * The private event interface also issues events for the hotkeys. As
+ * the driver gained features, the event handling code ended up being
+ * built around the hotkey subdriver. This will need to be refactored
+ * to a more formal event API eventually.
+ *
+ * Some "hotkeys" are actually supposed to be used as event reports,
+ * such as "brightness has changed", "volume has changed", depending on
+ * the ThinkPad model and how the firmware is operating.
+ *
+ * Unlike other classes, hotkey-class events have mask/unmask control on
+ * non-ancient firmware. However, how it behaves changes a lot with the
+ * firmware model and version.
+ */
+
enum { /* hot key scan codes (derived from ACPI DSDT) */
TP_ACPI_HOTKEYSCAN_FNF1 = 0,
TP_ACPI_HOTKEYSCAN_FNF2,
TP_ACPI_HOTKEYSCAN_THINKPAD,
};
-enum { /* Keys available through NVRAM polling */
+enum { /* Keys/events available through NVRAM polling */
TPACPI_HKEY_NVRAM_KNOWN_MASK = 0x00fb88c0U,
TPACPI_HKEY_NVRAM_GOOD_MASK = 0x00fb8000U,
};
static struct mutex hotkey_thread_mutex;
/*
- * Acquire mutex to write poller control variables.
- * Increment hotkey_config_change when changing them.
+ * Acquire mutex to write poller control variables as an
+ * atomic block.
+ *
+ * Increment hotkey_config_change when changing them if you
+ * want the kthread to forget old state.
*
* See HOTKEY_CONFIG_CRITICAL_START/HOTKEY_CONFIG_CRITICAL_END
*/
* hotkey poller control variables
*
* Must be atomic or readers will also need to acquire mutex
+ *
+ * HOTKEY_CONFIG_CRITICAL_START/HOTKEY_CONFIG_CRITICAL_END
+ * should be used only when the changes need to be taken as
+ * a block, OR when one needs to force the kthread to forget
+ * old state.
*/
static u32 hotkey_source_mask; /* bit mask 0=ACPI,1=NVRAM */
static unsigned int hotkey_poll_freq = 10; /* Hz */
static int hotkey_autosleep_ack;
-static u32 hotkey_orig_mask;
-static u32 hotkey_all_mask;
-static u32 hotkey_reserved_mask;
-static u32 hotkey_mask;
+static u32 hotkey_orig_mask; /* events the BIOS had enabled */
+static u32 hotkey_all_mask; /* all events supported in fw */
+static u32 hotkey_reserved_mask; /* events better left disabled */
+static u32 hotkey_driver_mask; /* events needed by the driver */
+static u32 hotkey_user_mask; /* events visible to userspace */
+static u32 hotkey_acpi_mask; /* events enabled in firmware */
static unsigned int hotkey_report_mode;
static struct attribute_set *hotkey_dev_attributes;
+static void tpacpi_driver_event(const unsigned int hkey_event);
+static void hotkey_driver_event(const unsigned int scancode);
+
/* HKEY.MHKG() return bits */
#define TP_HOTKEY_TABLET_MASK (1 << 3)
}
/*
+ * Reads current event mask from firmware, and updates
+ * hotkey_acpi_mask accordingly. Also resets any bits
+ * from hotkey_user_mask that are unavailable to be
+ * delivered (shadow requirement of the userspace ABI).
+ *
* Call with hotkey_mutex held
*/
static int hotkey_mask_get(void)
{
- u32 m = 0;
-
if (tp_features.hotkey_mask) {
+ u32 m = 0;
+
if (!acpi_evalf(hkey_handle, &m, "DHKN", "d"))
return -EIO;
+
+ hotkey_acpi_mask = m;
+ } else {
+ /* no mask support doesn't mean no event support... */
+ hotkey_acpi_mask = hotkey_all_mask;
}
- HOTKEY_CONFIG_CRITICAL_START
- hotkey_mask = m | (hotkey_source_mask & hotkey_mask);
- HOTKEY_CONFIG_CRITICAL_END
+
+ /* sync userspace-visible mask */
+ hotkey_user_mask &= (hotkey_acpi_mask | hotkey_source_mask);
return 0;
}
+void static hotkey_mask_warn_incomplete_mask(void)
+{
+ /* log only what the user can fix... */
+ const u32 wantedmask = hotkey_driver_mask &
+ ~(hotkey_acpi_mask | hotkey_source_mask) &
+ (hotkey_all_mask | TPACPI_HKEY_NVRAM_KNOWN_MASK);
+
+ if (wantedmask)
+ printk(TPACPI_NOTICE
+ "required events 0x%08x not enabled!\n",
+ wantedmask);
+}
+
/*
+ * Set the firmware mask when supported
+ *
+ * Also calls hotkey_mask_get to update hotkey_acpi_mask.
+ *
+ * NOTE: does not set bits in hotkey_user_mask, but may reset them.
+ *
* Call with hotkey_mutex held
*/
static int hotkey_mask_set(u32 mask)
int i;
int rc = 0;
- if (tp_features.hotkey_mask) {
- if (!tp_warned.hotkey_mask_ff &&
- (mask == 0xffff || mask == 0xffffff ||
- mask == 0xffffffff)) {
- tp_warned.hotkey_mask_ff = 1;
- printk(TPACPI_NOTICE
- "setting the hotkey mask to 0x%08x is likely "
- "not the best way to go about it\n", mask);
- printk(TPACPI_NOTICE
- "please consider using the driver defaults, "
- "and refer to up-to-date thinkpad-acpi "
- "documentation\n");
- }
+ const u32 fwmask = mask & ~hotkey_source_mask;
- HOTKEY_CONFIG_CRITICAL_START
+ if (tp_features.hotkey_mask) {
for (i = 0; i < 32; i++) {
- u32 m = 1 << i;
- /* enable in firmware mask only keys not in NVRAM
- * mode, but enable the key in the cached hotkey_mask
- * regardless of mode, or the key will end up
- * disabled by hotkey_mask_get() */
if (!acpi_evalf(hkey_handle,
NULL, "MHKM", "vdd", i + 1,
- !!((mask & ~hotkey_source_mask) & m))) {
+ !!(mask & (1 << i)))) {
rc = -EIO;
break;
- } else {
- hotkey_mask = (hotkey_mask & ~m) | (mask & m);
}
}
- HOTKEY_CONFIG_CRITICAL_END
+ }
- /* hotkey_mask_get must be called unconditionally below */
- if (!hotkey_mask_get() && !rc &&
- (hotkey_mask & ~hotkey_source_mask) !=
- (mask & ~hotkey_source_mask)) {
- printk(TPACPI_NOTICE
- "requested hot key mask 0x%08x, but "
- "firmware forced it to 0x%08x\n",
- mask, hotkey_mask);
- }
- } else {
-#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
- HOTKEY_CONFIG_CRITICAL_START
- hotkey_mask = mask & hotkey_source_mask;
- HOTKEY_CONFIG_CRITICAL_END
- hotkey_mask_get();
- if (hotkey_mask != mask) {
- printk(TPACPI_NOTICE
- "requested hot key mask 0x%08x, "
- "forced to 0x%08x (NVRAM poll mask is "
- "0x%08x): no firmware mask support\n",
- mask, hotkey_mask, hotkey_source_mask);
- }
-#else
- hotkey_mask_get();
- rc = -ENXIO;
-#endif /* CONFIG_THINKPAD_ACPI_HOTKEY_POLL */
+ /*
+ * We *must* make an inconditional call to hotkey_mask_get to
+ * refresh hotkey_acpi_mask and update hotkey_user_mask
+ *
+ * Take the opportunity to also log when we cannot _enable_
+ * a given event.
+ */
+ if (!hotkey_mask_get() && !rc && (fwmask & ~hotkey_acpi_mask)) {
+ printk(TPACPI_NOTICE
+ "asked for hotkey mask 0x%08x, but "
+ "firmware forced it to 0x%08x\n",
+ fwmask, hotkey_acpi_mask);
}
+ hotkey_mask_warn_incomplete_mask();
+
+ return rc;
+}
+
+/*
+ * Sets hotkey_user_mask and tries to set the firmware mask
+ *
+ * Call with hotkey_mutex held
+ */
+static int hotkey_user_mask_set(const u32 mask)
+{
+ int rc;
+
+ /* Give people a chance to notice they are doing something that
+ * is bound to go boom on their users sooner or later */
+ if (!tp_warned.hotkey_mask_ff &&
+ (mask == 0xffff || mask == 0xffffff ||
+ mask == 0xffffffff)) {
+ tp_warned.hotkey_mask_ff = 1;
+ printk(TPACPI_NOTICE
+ "setting the hotkey mask to 0x%08x is likely "
+ "not the best way to go about it\n", mask);
+ printk(TPACPI_NOTICE
+ "please consider using the driver defaults, "
+ "and refer to up-to-date thinkpad-acpi "
+ "documentation\n");
+ }
+
+ /* Try to enable what the user asked for, plus whatever we need.
+ * this syncs everything but won't enable bits in hotkey_user_mask */
+ rc = hotkey_mask_set((mask | hotkey_driver_mask) & ~hotkey_source_mask);
+
+ /* Enable the available bits in hotkey_user_mask */
+ hotkey_user_mask = mask & (hotkey_acpi_mask | hotkey_source_mask);
+
+ return rc;
+}
+
+/*
+ * Sets the driver hotkey mask.
+ *
+ * Can be called even if the hotkey subdriver is inactive
+ */
+static int tpacpi_hotkey_driver_mask_set(const u32 mask)
+{
+ int rc;
+
+ /* Do the right thing if hotkey_init has not been called yet */
+ if (!tp_features.hotkey) {
+ hotkey_driver_mask = mask;
+ return 0;
+ }
+
+ mutex_lock(&hotkey_mutex);
+
+ HOTKEY_CONFIG_CRITICAL_START
+ hotkey_driver_mask = mask;
+#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
+ hotkey_source_mask |= (mask & ~hotkey_all_mask);
+#endif
+ HOTKEY_CONFIG_CRITICAL_END
+
+ rc = hotkey_mask_set((hotkey_acpi_mask | hotkey_driver_mask) &
+ ~hotkey_source_mask);
+ mutex_unlock(&hotkey_mutex);
+
return rc;
}
}
}
-static void tpacpi_input_send_key(unsigned int scancode)
+/* Do NOT call without validating scancode first */
+static void tpacpi_input_send_key(const unsigned int scancode)
{
- unsigned int keycode;
-
- keycode = hotkey_keycode_map[scancode];
+ const unsigned int keycode = hotkey_keycode_map[scancode];
if (keycode != KEY_RESERVED) {
mutex_lock(&tpacpi_inputdev_send_mutex);
}
}
+/* Do NOT call without validating scancode first */
+static void tpacpi_input_send_key_masked(const unsigned int scancode)
+{
+ hotkey_driver_event(scancode);
+ if (hotkey_user_mask & (1 << scancode))
+ tpacpi_input_send_key(scancode);
+}
+
#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
static struct tp_acpi_drv_struct ibm_hotkey_acpidriver;
+/* Do NOT call without validating scancode first */
static void tpacpi_hotkey_send_key(unsigned int scancode)
{
- tpacpi_input_send_key(scancode);
+ tpacpi_input_send_key_masked(scancode);
if (hotkey_report_mode < 2) {
acpi_bus_generate_proc_event(ibm_hotkey_acpidriver.device,
- 0x80, 0x1001 + scancode);
+ 0x80, TP_HKEY_EV_HOTKEY_BASE + scancode);
}
}
-static void hotkey_read_nvram(struct tp_nvram_state *n, u32 m)
+static void hotkey_read_nvram(struct tp_nvram_state *n, const u32 m)
{
u8 d;
}
}
+static void hotkey_compare_and_issue_event(struct tp_nvram_state *oldn,
+ struct tp_nvram_state *newn,
+ const u32 event_mask)
+{
+
#define TPACPI_COMPARE_KEY(__scancode, __member) \
do { \
- if ((mask & (1 << __scancode)) && \
+ if ((event_mask & (1 << __scancode)) && \
oldn->__member != newn->__member) \
- tpacpi_hotkey_send_key(__scancode); \
+ tpacpi_hotkey_send_key(__scancode); \
} while (0)
#define TPACPI_MAY_SEND_KEY(__scancode) \
- do { if (mask & (1 << __scancode)) \
- tpacpi_hotkey_send_key(__scancode); } while (0)
+ do { \
+ if (event_mask & (1 << __scancode)) \
+ tpacpi_hotkey_send_key(__scancode); \
+ } while (0)
-static void hotkey_compare_and_issue_event(struct tp_nvram_state *oldn,
- struct tp_nvram_state *newn,
- u32 mask)
-{
TPACPI_COMPARE_KEY(TP_ACPI_HOTKEYSCAN_THINKPAD, thinkpad_toggle);
TPACPI_COMPARE_KEY(TP_ACPI_HOTKEYSCAN_FNSPACE, zoom_toggle);
TPACPI_COMPARE_KEY(TP_ACPI_HOTKEYSCAN_FNF7, display_toggle);
}
}
}
-}
#undef TPACPI_COMPARE_KEY
#undef TPACPI_MAY_SEND_KEY
+}
+/*
+ * Polling driver
+ *
+ * We track all events in hotkey_source_mask all the time, since
+ * most of them are edge-based. We only issue those requested by
+ * hotkey_user_mask or hotkey_driver_mask, though.
+ */
static int hotkey_kthread(void *data)
{
struct tp_nvram_state s[2];
- u32 mask;
+ u32 poll_mask, event_mask;
unsigned int si, so;
unsigned long t;
unsigned int change_detector, must_reset;
/* Initial state for compares */
mutex_lock(&hotkey_thread_data_mutex);
change_detector = hotkey_config_change;
- mask = hotkey_source_mask & hotkey_mask;
+ poll_mask = hotkey_source_mask;
+ event_mask = hotkey_source_mask &
+ (hotkey_driver_mask | hotkey_user_mask);
poll_freq = hotkey_poll_freq;
mutex_unlock(&hotkey_thread_data_mutex);
- hotkey_read_nvram(&s[so], mask);
+ hotkey_read_nvram(&s[so], poll_mask);
while (!kthread_should_stop()) {
if (t == 0) {
t = 0;
change_detector = hotkey_config_change;
}
- mask = hotkey_source_mask & hotkey_mask;
+ poll_mask = hotkey_source_mask;
+ event_mask = hotkey_source_mask &
+ (hotkey_driver_mask | hotkey_user_mask);
poll_freq = hotkey_poll_freq;
mutex_unlock(&hotkey_thread_data_mutex);
- if (likely(mask)) {
- hotkey_read_nvram(&s[si], mask);
+ if (likely(poll_mask)) {
+ hotkey_read_nvram(&s[si], poll_mask);
if (likely(si != so)) {
hotkey_compare_and_issue_event(&s[so], &s[si],
- mask);
+ event_mask);
}
}
/* call with hotkey_mutex held */
static void hotkey_poll_setup(bool may_warn)
{
- u32 hotkeys_to_poll = hotkey_source_mask & hotkey_mask;
+ const u32 poll_driver_mask = hotkey_driver_mask & hotkey_source_mask;
+ const u32 poll_user_mask = hotkey_user_mask & hotkey_source_mask;
- if (hotkeys_to_poll != 0 && hotkey_poll_freq > 0 &&
- (tpacpi_inputdev->users > 0 || hotkey_report_mode < 2)) {
+ if (hotkey_poll_freq > 0 &&
+ (poll_driver_mask ||
+ (poll_user_mask && tpacpi_inputdev->users > 0))) {
if (!tpacpi_hotkey_task) {
tpacpi_hotkey_task = kthread_run(hotkey_kthread,
NULL, TPACPI_NVRAM_KTHREAD_NAME);
}
} else {
hotkey_poll_stop_sync();
- if (may_warn && hotkeys_to_poll != 0 &&
+ if (may_warn && (poll_driver_mask || poll_user_mask) &&
hotkey_poll_freq == 0) {
printk(TPACPI_NOTICE
- "hot keys 0x%08x require polling, "
- "which is currently disabled\n",
- hotkeys_to_poll);
+ "hot keys 0x%08x and/or events 0x%08x "
+ "require polling, which is currently "
+ "disabled\n",
+ poll_user_mask, poll_driver_mask);
}
}
}
if (!freq)
hotkey_poll_stop_sync();
- HOTKEY_CONFIG_CRITICAL_START
hotkey_poll_freq = freq;
- HOTKEY_CONFIG_CRITICAL_END
}
#else /* CONFIG_THINKPAD_ACPI_HOTKEY_POLL */
static void hotkey_inputdev_close(struct input_dev *dev)
{
/* disable hotkey polling when possible */
- if (tpacpi_lifecycle == TPACPI_LIFE_RUNNING)
+ if (tpacpi_lifecycle == TPACPI_LIFE_RUNNING &&
+ !(hotkey_source_mask & hotkey_driver_mask))
hotkey_poll_setup_safe(false);
}
struct device_attribute *attr,
char *buf)
{
- int res;
-
- if (mutex_lock_killable(&hotkey_mutex))
- return -ERESTARTSYS;
- res = hotkey_mask_get();
- mutex_unlock(&hotkey_mutex);
-
- return (res)?
- res : snprintf(buf, PAGE_SIZE, "0x%08x\n", hotkey_mask);
+ return snprintf(buf, PAGE_SIZE, "0x%08x\n", hotkey_user_mask);
}
static ssize_t hotkey_mask_store(struct device *dev,
if (mutex_lock_killable(&hotkey_mutex))
return -ERESTARTSYS;
- res = hotkey_mask_set(t);
+ res = hotkey_user_mask_set(t);
#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
hotkey_poll_setup(true);
const char *buf, size_t count)
{
unsigned long t;
+ u32 r_ev;
+ int rc;
if (parse_strtoul(buf, 0xffffffffUL, &t) ||
((t & ~TPACPI_HKEY_NVRAM_KNOWN_MASK) != 0))
hotkey_source_mask = t;
HOTKEY_CONFIG_CRITICAL_END
+ rc = hotkey_mask_set((hotkey_user_mask | hotkey_driver_mask) &
+ ~hotkey_source_mask);
hotkey_poll_setup(true);
- hotkey_mask_set(hotkey_mask);
+
+ /* check if events needed by the driver got disabled */
+ r_ev = hotkey_driver_mask & ~(hotkey_acpi_mask & hotkey_all_mask)
+ & ~hotkey_source_mask & TPACPI_HKEY_NVRAM_KNOWN_MASK;
mutex_unlock(&hotkey_mutex);
+ if (rc < 0)
+ printk(TPACPI_ERR "hotkey_source_mask: failed to update the"
+ "firmware event mask!\n");
+
+ if (r_ev)
+ printk(TPACPI_NOTICE "hotkey_source_mask: "
+ "some important events were disabled: "
+ "0x%04x\n", r_ev);
+
tpacpi_disclose_usertask("hotkey_source_mask", "set to 0x%08lx\n", t);
- return count;
+ return (rc < 0) ? rc : count;
}
static struct device_attribute dev_attr_hotkey_source_mask =
static void hotkey_wakeup_reason_notify_change(void)
{
- if (tp_features.hotkey_mask)
- sysfs_notify(&tpacpi_pdev->dev.kobj, NULL,
- "wakeup_reason");
+ sysfs_notify(&tpacpi_pdev->dev.kobj, NULL,
+ "wakeup_reason");
}
/* sysfs wakeup hotunplug_complete (pollable) -------------------------- */
static void hotkey_wakeup_hotunplug_complete_notify_change(void)
{
- if (tp_features.hotkey_mask)
- sysfs_notify(&tpacpi_pdev->dev.kobj, NULL,
- "wakeup_hotunplug_complete");
+ sysfs_notify(&tpacpi_pdev->dev.kobj, NULL,
+ "wakeup_hotunplug_complete");
}
/* --------------------------------------------------------------------- */
static struct attribute *hotkey_attributes[] __initdata = {
&dev_attr_hotkey_enable.attr,
&dev_attr_hotkey_bios_enabled.attr,
+ &dev_attr_hotkey_bios_mask.attr,
&dev_attr_hotkey_report_mode.attr,
-#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
+ &dev_attr_hotkey_wakeup_reason.attr,
+ &dev_attr_hotkey_wakeup_hotunplug_complete.attr,
&dev_attr_hotkey_mask.attr,
&dev_attr_hotkey_all_mask.attr,
&dev_attr_hotkey_recommended_mask.attr,
+#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
&dev_attr_hotkey_source_mask.attr,
&dev_attr_hotkey_poll_freq.attr,
#endif
};
-static struct attribute *hotkey_mask_attributes[] __initdata = {
- &dev_attr_hotkey_bios_mask.attr,
-#ifndef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
- &dev_attr_hotkey_mask.attr,
- &dev_attr_hotkey_all_mask.attr,
- &dev_attr_hotkey_recommended_mask.attr,
-#endif
- &dev_attr_hotkey_wakeup_reason.attr,
- &dev_attr_hotkey_wakeup_hotunplug_complete.attr,
-};
-
/*
* Sync both the hw and sw blocking state of all switches
*/
kfree(hotkey_keycode_map);
- if (tp_features.hotkey) {
- dbg_printk(TPACPI_DBG_EXIT | TPACPI_DBG_HKEY,
- "restoring original hot key mask\n");
- /* no short-circuit boolean operator below! */
- if ((hotkey_mask_set(hotkey_orig_mask) |
- hotkey_status_set(false)) != 0)
- printk(TPACPI_ERR
- "failed to restore hot key mask "
- "to BIOS defaults\n");
- }
+ dbg_printk(TPACPI_DBG_EXIT | TPACPI_DBG_HKEY,
+ "restoring original HKEY status and mask\n");
+ /* yes, there is a bitwise or below, we want the
+ * functions to be called even if one of them fail */
+ if (((tp_features.hotkey_mask &&
+ hotkey_mask_set(hotkey_orig_mask)) |
+ hotkey_status_set(false)) != 0)
+ printk(TPACPI_ERR
+ "failed to restore hot key mask "
+ "to BIOS defaults\n");
}
static void __init hotkey_unmap(const unsigned int scancode)
}
}
+/*
+ * HKEY quirks:
+ * TPACPI_HK_Q_INIMASK: Supports FN+F3,FN+F4,FN+F12
+ */
+
+#define TPACPI_HK_Q_INIMASK 0x0001
+
+static const struct tpacpi_quirk tpacpi_hotkey_qtable[] __initconst = {
+ TPACPI_Q_IBM('I', 'H', TPACPI_HK_Q_INIMASK), /* 600E */
+ TPACPI_Q_IBM('I', 'N', TPACPI_HK_Q_INIMASK), /* 600E */
+ TPACPI_Q_IBM('I', 'D', TPACPI_HK_Q_INIMASK), /* 770, 770E, 770ED */
+ TPACPI_Q_IBM('I', 'W', TPACPI_HK_Q_INIMASK), /* A20m */
+ TPACPI_Q_IBM('I', 'V', TPACPI_HK_Q_INIMASK), /* A20p */
+ TPACPI_Q_IBM('1', '0', TPACPI_HK_Q_INIMASK), /* A21e, A22e */
+ TPACPI_Q_IBM('K', 'U', TPACPI_HK_Q_INIMASK), /* A21e */
+ TPACPI_Q_IBM('K', 'X', TPACPI_HK_Q_INIMASK), /* A21m, A22m */
+ TPACPI_Q_IBM('K', 'Y', TPACPI_HK_Q_INIMASK), /* A21p, A22p */
+ TPACPI_Q_IBM('1', 'B', TPACPI_HK_Q_INIMASK), /* A22e */
+ TPACPI_Q_IBM('1', '3', TPACPI_HK_Q_INIMASK), /* A22m */
+ TPACPI_Q_IBM('1', 'E', TPACPI_HK_Q_INIMASK), /* A30/p (0) */
+ TPACPI_Q_IBM('1', 'C', TPACPI_HK_Q_INIMASK), /* R30 */
+ TPACPI_Q_IBM('1', 'F', TPACPI_HK_Q_INIMASK), /* R31 */
+ TPACPI_Q_IBM('I', 'Y', TPACPI_HK_Q_INIMASK), /* T20 */
+ TPACPI_Q_IBM('K', 'Z', TPACPI_HK_Q_INIMASK), /* T21 */
+ TPACPI_Q_IBM('1', '6', TPACPI_HK_Q_INIMASK), /* T22 */
+ TPACPI_Q_IBM('I', 'Z', TPACPI_HK_Q_INIMASK), /* X20, X21 */
+ TPACPI_Q_IBM('1', 'D', TPACPI_HK_Q_INIMASK), /* X22, X23, X24 */
+};
+
static int __init hotkey_init(struct ibm_init_struct *iibm)
{
/* Requirements for changing the default keymaps:
KEY_UNKNOWN, /* 0x0D: FN+INSERT */
KEY_UNKNOWN, /* 0x0E: FN+DELETE */
- /* brightness: firmware always reacts to them, unless
- * X.org did some tricks in the radeon BIOS scratch
- * registers of *some* models */
+ /* brightness: firmware always reacts to them */
KEY_RESERVED, /* 0x0F: FN+HOME (brightness up) */
KEY_RESERVED, /* 0x10: FN+END (brightness down) */
int status;
int hkeyv;
+ unsigned long quirks;
+
vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_HKEY,
"initializing hotkey subdriver\n");
if (!tp_features.hotkey)
return 1;
+ quirks = tpacpi_check_quirks(tpacpi_hotkey_qtable,
+ ARRAY_SIZE(tpacpi_hotkey_qtable));
+
tpacpi_disable_brightness_delay();
- hotkey_dev_attributes = create_attr_set(13, NULL);
+ /* MUST have enough space for all attributes to be added to
+ * hotkey_dev_attributes */
+ hotkey_dev_attributes = create_attr_set(
+ ARRAY_SIZE(hotkey_attributes) + 2,
+ NULL);
if (!hotkey_dev_attributes)
return -ENOMEM;
res = add_many_to_attr_set(hotkey_dev_attributes,
if (res)
goto err_exit;
- /* mask not supported on 570, 600e/x, 770e, 770x, A21e, A2xm/p,
+ /* mask not supported on 600e/x, 770e, 770x, A21e, A2xm/p,
A30, R30, R31, T20-22, X20-21, X22-24. Detected by checking
for HKEY interface version 0x100 */
if (acpi_evalf(hkey_handle, &hkeyv, "MHKV", "qd")) {
* MHKV 0x100 in A31, R40, R40e,
* T4x, X31, and later
*/
- tp_features.hotkey_mask = 1;
vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_HKEY,
"firmware HKEY interface version: 0x%x\n",
hkeyv);
+
+ /* Paranoia check AND init hotkey_all_mask */
+ if (!acpi_evalf(hkey_handle, &hotkey_all_mask,
+ "MHKA", "qd")) {
+ printk(TPACPI_ERR
+ "missing MHKA handler, "
+ "please report this to %s\n",
+ TPACPI_MAIL);
+ /* Fallback: pre-init for FN+F3,F4,F12 */
+ hotkey_all_mask = 0x080cU;
+ } else {
+ tp_features.hotkey_mask = 1;
+ }
}
}
"hotkey masks are %s\n",
str_supported(tp_features.hotkey_mask));
- if (tp_features.hotkey_mask) {
- if (!acpi_evalf(hkey_handle, &hotkey_all_mask,
- "MHKA", "qd")) {
- printk(TPACPI_ERR
- "missing MHKA handler, "
- "please report this to %s\n",
- TPACPI_MAIL);
- /* FN+F12, FN+F4, FN+F3 */
- hotkey_all_mask = 0x080cU;
- }
- }
+ /* Init hotkey_all_mask if not initialized yet */
+ if (!tp_features.hotkey_mask && !hotkey_all_mask &&
+ (quirks & TPACPI_HK_Q_INIMASK))
+ hotkey_all_mask = 0x080cU; /* FN+F12, FN+F4, FN+F3 */
- /* hotkey_source_mask *must* be zero for
- * the first hotkey_mask_get */
+ /* Init hotkey_acpi_mask and hotkey_orig_mask */
if (tp_features.hotkey_mask) {
+ /* hotkey_source_mask *must* be zero for
+ * the first hotkey_mask_get to return hotkey_orig_mask */
res = hotkey_mask_get();
if (res)
goto err_exit;
- hotkey_orig_mask = hotkey_mask;
- res = add_many_to_attr_set(
- hotkey_dev_attributes,
- hotkey_mask_attributes,
- ARRAY_SIZE(hotkey_mask_attributes));
- if (res)
- goto err_exit;
+ hotkey_orig_mask = hotkey_acpi_mask;
+ } else {
+ hotkey_orig_mask = hotkey_all_mask;
+ hotkey_acpi_mask = hotkey_all_mask;
}
#ifdef CONFIG_THINKPAD_ACPI_DEBUGFACILITIES
}
#ifdef CONFIG_THINKPAD_ACPI_HOTKEY_POLL
- if (tp_features.hotkey_mask) {
- hotkey_source_mask = TPACPI_HKEY_NVRAM_GOOD_MASK
- & ~hotkey_all_mask
- & ~hotkey_reserved_mask;
- } else {
- hotkey_source_mask = TPACPI_HKEY_NVRAM_GOOD_MASK
- & ~hotkey_reserved_mask;
- }
+ hotkey_source_mask = TPACPI_HKEY_NVRAM_GOOD_MASK
+ & ~hotkey_all_mask
+ & ~hotkey_reserved_mask;
vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_HKEY,
"hotkey source mask 0x%08x, polling freq %u\n",
hotkey_exit();
return res;
}
- res = hotkey_mask_set(((hotkey_all_mask | hotkey_source_mask)
- & ~hotkey_reserved_mask)
- | hotkey_orig_mask);
+ res = hotkey_mask_set(((hotkey_all_mask & ~hotkey_reserved_mask)
+ | hotkey_driver_mask)
+ & ~hotkey_source_mask);
if (res < 0 && res != -ENXIO) {
hotkey_exit();
return res;
}
+ hotkey_user_mask = (hotkey_acpi_mask | hotkey_source_mask)
+ & ~hotkey_reserved_mask;
+ vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_HKEY,
+ "initial masks: user=0x%08x, fw=0x%08x, poll=0x%08x\n",
+ hotkey_user_mask, hotkey_acpi_mask, hotkey_source_mask);
dbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_HKEY,
"legacy ibm/hotkey event reporting over procfs %s\n",
if (scancode > 0 && scancode < 0x21) {
scancode--;
if (!(hotkey_source_mask & (1 << scancode))) {
- tpacpi_input_send_key(scancode);
+ tpacpi_input_send_key_masked(scancode);
*send_acpi_ev = false;
} else {
*ignore_acpi_ev = true;
*ignore_acpi_ev = false;
switch (hkey) {
- case 0x2304: /* suspend, undock */
- case 0x2404: /* hibernation, undock */
+ case TP_HKEY_EV_WKUP_S3_UNDOCK: /* suspend, undock */
+ case TP_HKEY_EV_WKUP_S4_UNDOCK: /* hibernation, undock */
hotkey_wakeup_reason = TP_ACPI_WAKEUP_UNDOCK;
*ignore_acpi_ev = true;
break;
- case 0x2305: /* suspend, bay eject */
- case 0x2405: /* hibernation, bay eject */
+ case TP_HKEY_EV_WKUP_S3_BAYEJ: /* suspend, bay eject */
+ case TP_HKEY_EV_WKUP_S4_BAYEJ: /* hibernation, bay eject */
hotkey_wakeup_reason = TP_ACPI_WAKEUP_BAYEJ;
*ignore_acpi_ev = true;
break;
- case 0x2313: /* Battery on critical low level (S3) */
- case 0x2413: /* Battery on critical low level (S4) */
+ case TP_HKEY_EV_WKUP_S3_BATLOW: /* Battery on critical low level/S3 */
+ case TP_HKEY_EV_WKUP_S4_BATLOW: /* Battery on critical low level/S4 */
printk(TPACPI_ALERT
"EMERGENCY WAKEUP: battery almost empty\n");
/* how to auto-heal: */
*ignore_acpi_ev = false;
switch (hkey) {
- case 0x5010: /* Lenovo new BIOS: brightness changed */
- case 0x500b: /* X61t: tablet pen inserted into bay */
- case 0x500c: /* X61t: tablet pen removed from bay */
+ case TP_HKEY_EV_PEN_INSERTED: /* X61t: tablet pen inserted into bay */
+ case TP_HKEY_EV_PEN_REMOVED: /* X61t: tablet pen removed from bay */
return true;
- case 0x5009: /* X41t-X61t: swivel up (tablet mode) */
- case 0x500a: /* X41t-X61t: swivel down (normal mode) */
+ case TP_HKEY_EV_TABLET_TABLET: /* X41t-X61t: tablet mode */
+ case TP_HKEY_EV_TABLET_NOTEBOOK: /* X41t-X61t: normal mode */
tpacpi_input_send_tabletsw();
hotkey_tablet_mode_notify_change();
*send_acpi_ev = false;
return true;
- case 0x5001:
- case 0x5002:
- /* LID switch events. Do not propagate */
+ case TP_HKEY_EV_LID_CLOSE: /* Lid closed */
+ case TP_HKEY_EV_LID_OPEN: /* Lid opened */
+ case TP_HKEY_EV_BRGHT_CHANGED: /* brightness changed */
+ /* do not propagate these events */
*ignore_acpi_ev = true;
return true;
*ignore_acpi_ev = false;
switch (hkey) {
- case 0x6011:
+ case TP_HKEY_EV_ALARM_BAT_HOT:
printk(TPACPI_CRIT
"THERMAL ALARM: battery is too hot!\n");
/* recommended action: warn user through gui */
return true;
- case 0x6012:
+ case TP_HKEY_EV_ALARM_BAT_XHOT:
printk(TPACPI_ALERT
"THERMAL EMERGENCY: battery is extremely hot!\n");
/* recommended action: immediate sleep/hibernate */
return true;
- case 0x6021:
+ case TP_HKEY_EV_ALARM_SENSOR_HOT:
printk(TPACPI_CRIT
"THERMAL ALARM: "
"a sensor reports something is too hot!\n");
/* recommended action: warn user through gui, that */
/* some internal component is too hot */
return true;
- case 0x6022:
+ case TP_HKEY_EV_ALARM_SENSOR_XHOT:
printk(TPACPI_ALERT
"THERMAL EMERGENCY: "
"a sensor reports something is extremely hot!\n");
/* recommended action: immediate sleep/hibernate */
return true;
- case 0x6030:
+ case TP_HKEY_EV_THM_TABLE_CHANGED:
printk(TPACPI_INFO
"EC reports that Thermal Table has changed\n");
/* recommended action: do nothing, we don't have
break;
case 3:
/* 0x3000-0x3FFF: bay-related wakeups */
- if (hkey == 0x3003) {
+ if (hkey == TP_HKEY_EV_BAYEJ_ACK) {
hotkey_autosleep_ack = 1;
printk(TPACPI_INFO
"bay ejected\n");
break;
case 4:
/* 0x4000-0x4FFF: dock-related wakeups */
- if (hkey == 0x4003) {
+ if (hkey == TP_HKEY_EV_UNDOCK_ACK) {
hotkey_autosleep_ack = 1;
printk(TPACPI_INFO
"undocked\n");
break;
case 7:
/* 0x7000-0x7FFF: misc */
- if (tp_features.hotkey_wlsw && hkey == 0x7000) {
+ if (tp_features.hotkey_wlsw &&
+ hkey == TP_HKEY_EV_RFKILL_CHANGED) {
tpacpi_send_radiosw_update();
send_acpi_ev = 0;
known_ev = true;
{
tpacpi_disable_brightness_delay();
- if (hotkey_mask_get())
+ if (hotkey_status_set(true) < 0 ||
+ hotkey_mask_set(hotkey_acpi_mask) < 0)
printk(TPACPI_ERR
- "error while trying to read hot key mask "
- "from firmware\n");
+ "error while attempting to reset the event "
+ "firmware interface\n");
+
tpacpi_send_radiosw_update();
hotkey_tablet_mode_notify_change();
hotkey_wakeup_reason_notify_change();
return res;
len += sprintf(p + len, "status:\t\t%s\n", enabled(status, 0));
- if (tp_features.hotkey_mask) {
- len += sprintf(p + len, "mask:\t\t0x%08x\n", hotkey_mask);
+ if (hotkey_all_mask) {
+ len += sprintf(p + len, "mask:\t\t0x%08x\n", hotkey_user_mask);
len += sprintf(p + len,
"commands:\tenable, disable, reset, <mask>\n");
} else {
if (mutex_lock_killable(&hotkey_mutex))
return -ERESTARTSYS;
- mask = hotkey_mask;
+ mask = hotkey_user_mask;
res = 0;
while ((cmd = next_cmd(&buf))) {
}
}
- if (!res)
+ if (!res) {
tpacpi_disclose_usertask("procfs hotkey",
"set mask to 0x%08x\n", mask);
-
- if (!res && mask != hotkey_mask)
- res = hotkey_mask_set(mask);
+ res = hotkey_user_mask_set(mask);
+ }
errexit:
mutex_unlock(&hotkey_mutex);
TPACPI_BACKLIGHT_DEV_NAME, NULL, NULL,
&ibm_backlight_data);
if (IS_ERR(ibm_backlight_device)) {
+ int rc = PTR_ERR(ibm_backlight_device);
+ ibm_backlight_device = NULL;
printk(TPACPI_ERR "Could not register backlight device\n");
- return PTR_ERR(ibm_backlight_device);
+ return rc;
}
vdbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_BRGHT,
"brightness is supported\n");
****************************************************************************
****************************************************************************/
+/*
+ * HKEY event callout for other subdrivers go here
+ * (yes, it is ugly, but it is quick, safe, and gets the job done
+ */
+static void tpacpi_driver_event(const unsigned int hkey_event)
+{
+}
+
+
+
+static void hotkey_driver_event(const unsigned int scancode)
+{
+ tpacpi_driver_event(TP_HKEY_EV_HOTKEY_BASE + scancode);
+}
+
/* sysfs name ---------------------------------------------------------- */
static ssize_t thinkpad_acpi_pdev_name_show(struct device *dev,
struct device_attribute *attr,
acpi_handle temp = NULL;
acpi_status status;
struct pnp_dev *dev;
+ struct acpi_hardware_id *id;
/*
* If a PnPacpi device is not present , the device
if (dev->capabilities & PNP_CONFIGURABLE)
pnpacpi_parse_resource_option_data(dev);
- if (device->flags.compatible_ids) {
- struct acpica_device_id_list *cid_list = device->pnp.cid_list;
- int i;
-
- for (i = 0; i < cid_list->count; i++) {
- if (!ispnpidacpi(cid_list->ids[i].string))
- continue;
- pnp_add_id(dev, cid_list->ids[i].string);
- }
+ list_for_each_entry(id, &device->pnp.ids, list) {
+ if (!strcmp(id->id, acpi_device_hid(device)))
+ continue;
+ if (!ispnpidacpi(id->id))
+ continue;
+ pnp_add_id(dev, id->id);
}
/* clear out the damaged flags */
struct pnp_dev *pnp = _pnp;
/* true means it matched */
- return acpi->flags.hardware_id
- && !acpi_get_physical_device(acpi->handle)
- && compare_pnp_id(pnp->id, acpi->pnp.hardware_id);
+ return !acpi_get_physical_device(acpi->handle)
+ && compare_pnp_id(pnp->id, acpi_device_hid(acpi));
}
static int __init acpi_pnp_find_device(struct device *dev, acpi_handle * handle)
}
#ifdef CONFIG_PM
-static int pxa_rtc_suspend(struct platform_device *pdev, pm_message_t state)
+static int pxa_rtc_suspend(struct device *dev)
{
- struct pxa_rtc *pxa_rtc = platform_get_drvdata(pdev);
+ struct pxa_rtc *pxa_rtc = dev_get_drvdata(dev);
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
enable_irq_wake(pxa_rtc->irq_Alrm);
return 0;
}
-static int pxa_rtc_resume(struct platform_device *pdev)
+static int pxa_rtc_resume(struct device *dev)
{
- struct pxa_rtc *pxa_rtc = platform_get_drvdata(pdev);
+ struct pxa_rtc *pxa_rtc = dev_get_drvdata(dev);
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
disable_irq_wake(pxa_rtc->irq_Alrm);
return 0;
}
-#else
-#define pxa_rtc_suspend NULL
-#define pxa_rtc_resume NULL
+
+static struct dev_pm_ops pxa_rtc_pm_ops = {
+ .suspend = pxa_rtc_suspend,
+ .resume = pxa_rtc_resume,
+};
#endif
static struct platform_driver pxa_rtc_driver = {
.remove = __exit_p(pxa_rtc_remove),
- .suspend = pxa_rtc_suspend,
- .resume = pxa_rtc_resume,
.driver = {
- .name = "pxa-rtc",
+ .name = "pxa-rtc",
+#ifdef CONFIG_PM
+ .pm = &pxa_rtc_pm_ops,
+#endif
},
};
}
#ifdef CONFIG_PM
-static int sa1100_rtc_suspend(struct platform_device *pdev, pm_message_t state)
+static int sa1100_rtc_suspend(struct device *dev)
{
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
enable_irq_wake(IRQ_RTCAlrm);
return 0;
}
-static int sa1100_rtc_resume(struct platform_device *pdev)
+static int sa1100_rtc_resume(struct device *dev)
{
- if (device_may_wakeup(&pdev->dev))
+ if (device_may_wakeup(dev))
disable_irq_wake(IRQ_RTCAlrm);
return 0;
}
-#else
-#define sa1100_rtc_suspend NULL
-#define sa1100_rtc_resume NULL
+
+static struct dev_pm_ops sa1100_rtc_pm_ops = {
+ .suspend = sa1100_rtc_suspend,
+ .resume = sa1100_rtc_resume,
+};
#endif
static struct platform_driver sa1100_rtc_driver = {
.probe = sa1100_rtc_probe,
.remove = sa1100_rtc_remove,
- .suspend = sa1100_rtc_suspend,
- .resume = sa1100_rtc_resume,
.driver = {
- .name = "sa1100-rtc",
+ .name = "sa1100-rtc",
+#ifdef CONFIG_PM
+ .pm = &sa1100_rtc_pm_ops,
+#endif
},
};
filp->f_path.dentry->d_inode->i_private);
}
-static struct file_operations debugfs_fops = {
+static const struct file_operations debugfs_fops = {
.owner = THIS_MODULE,
.open = qstat_seq_open,
.read = seq_read,
return single_open(filp, qdio_perf_proc_show, NULL);
}
-static struct file_operations qdio_perf_proc_fops = {
+static const struct file_operations qdio_perf_proc_fops = {
.owner = THIS_MODULE,
.open = qdio_perf_seq_open,
.read = seq_read,
#include <linux/completion.h>
#include <linux/list.h>
#include <scsi/scsi.h>
-#include <linux/kref.h>
#include <scsi/scsi_cmnd.h>
#include <linux/cdev.h>
#include <net/netlink.h>
return VM_FAULT_SIGBUS;
}
-static struct vm_operations_struct sg_mmap_vm_ops = {
+static const struct vm_operations_struct sg_mmap_vm_ops = {
.fault = sg_vma_fault,
};
}
}
-static struct file_operations sg_fops = {
+static const struct file_operations sg_fops = {
.owner = THIS_MODULE,
.read = sg_read,
.write = sg_write,
static int sg_proc_single_open_adio(struct inode *inode, struct file *file);
static ssize_t sg_proc_write_adio(struct file *filp, const char __user *buffer,
size_t count, loff_t *off);
-static struct file_operations adio_fops = {
- /* .owner, .read and .llseek added in sg_proc_init() */
+static const struct file_operations adio_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_single_open_adio,
+ .read = seq_read,
+ .llseek = seq_lseek,
.write = sg_proc_write_adio,
.release = single_release,
};
static int sg_proc_single_open_dressz(struct inode *inode, struct file *file);
static ssize_t sg_proc_write_dressz(struct file *filp,
const char __user *buffer, size_t count, loff_t *off);
-static struct file_operations dressz_fops = {
+static const struct file_operations dressz_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_single_open_dressz,
+ .read = seq_read,
+ .llseek = seq_lseek,
.write = sg_proc_write_dressz,
.release = single_release,
};
static int sg_proc_seq_show_version(struct seq_file *s, void *v);
static int sg_proc_single_open_version(struct inode *inode, struct file *file);
-static struct file_operations version_fops = {
+static const struct file_operations version_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_single_open_version,
+ .read = seq_read,
+ .llseek = seq_lseek,
.release = single_release,
};
static int sg_proc_seq_show_devhdr(struct seq_file *s, void *v);
static int sg_proc_single_open_devhdr(struct inode *inode, struct file *file);
-static struct file_operations devhdr_fops = {
+static const struct file_operations devhdr_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_single_open_devhdr,
+ .read = seq_read,
+ .llseek = seq_lseek,
.release = single_release,
};
static void * dev_seq_start(struct seq_file *s, loff_t *pos);
static void * dev_seq_next(struct seq_file *s, void *v, loff_t *pos);
static void dev_seq_stop(struct seq_file *s, void *v);
-static struct file_operations dev_fops = {
+static const struct file_operations dev_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_open_dev,
+ .read = seq_read,
+ .llseek = seq_lseek,
.release = seq_release,
};
static const struct seq_operations dev_seq_ops = {
static int sg_proc_seq_show_devstrs(struct seq_file *s, void *v);
static int sg_proc_open_devstrs(struct inode *inode, struct file *file);
-static struct file_operations devstrs_fops = {
+static const struct file_operations devstrs_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_open_devstrs,
+ .read = seq_read,
+ .llseek = seq_lseek,
.release = seq_release,
};
static const struct seq_operations devstrs_seq_ops = {
static int sg_proc_seq_show_debug(struct seq_file *s, void *v);
static int sg_proc_open_debug(struct inode *inode, struct file *file);
-static struct file_operations debug_fops = {
+static const struct file_operations debug_fops = {
+ .owner = THIS_MODULE,
.open = sg_proc_open_debug,
+ .read = seq_read,
+ .llseek = seq_lseek,
.release = seq_release,
};
static const struct seq_operations debug_seq_ops = {
struct sg_proc_leaf {
const char * name;
- struct file_operations * fops;
+ const struct file_operations * fops;
};
static struct sg_proc_leaf sg_proc_leaf_arr[] = {
for (k = 0; k < num_leaves; ++k) {
leaf = &sg_proc_leaf_arr[k];
mask = leaf->fops->write ? S_IRUGO | S_IWUSR : S_IRUGO;
- leaf->fops->owner = THIS_MODULE;
- leaf->fops->read = seq_read;
- leaf->fops->llseek = seq_lseek;
proc_create(leaf->name, mask, sg_proc_sgp, leaf->fops);
}
return 0;
return (serial8250_reg.minor - 64) + port->line;
}
+static unsigned int skip_txen_test; /* force skip of txen test at init time */
+
/*
* Debugging.
*/
is variable. So, let's just don't test if we receive
TX irq. This way, we'll never enable UART_BUG_TXEN.
*/
- if (up->port.flags & UPF_NO_TXEN_TEST)
+ if (skip_txen_test || up->port.flags & UPF_NO_TXEN_TEST)
goto dont_test_tx_en;
/*
module_param(nr_uarts, uint, 0644);
MODULE_PARM_DESC(nr_uarts, "Maximum number of UARTs supported. (1-" __MODULE_STRING(CONFIG_SERIAL_8250_NR_UARTS) ")");
+module_param(skip_txen_test, uint, 0644);
+MODULE_PARM_DESC(skip_txen_test, "Skip checking for the TXEN bug at init time");
+
#ifdef CONFIG_SERIAL_8250_RSA
module_param_array(probe_rsa, ulong, &probe_rsa_count, 0444);
MODULE_PARM_DESC(probe_rsa, "Probe I/O ports for RSA");
config SERIAL_UARTLITE
tristate "Xilinx uartlite serial port support"
- depends on PPC32 || MICROBLAZE
+ depends on PPC32 || MICROBLAZE || MFD_TIMBERDALE
select SERIAL_CORE
help
Say Y here if you want to use the Xilinx uartlite serial controller.
---help---
Add support for UART controller on timberdale.
+config SERIAL_BCM63XX
+ tristate "bcm63xx serial port support"
+ select SERIAL_CORE
+ depends on BCM63XX
+ help
+ If you have a bcm63xx CPU, you can enable its onboard
+ serial port by enabling this options.
+
+ To compile this driver as a module, choose M here: the
+ module will be called bcm963xx_uart.
+
+config SERIAL_BCM63XX_CONSOLE
+ bool "Console on bcm63xx serial port"
+ depends on SERIAL_BCM63XX=y
+ select SERIAL_CORE_CONSOLE
+ help
+ If you have enabled the serial port on the bcm63xx CPU
+ you can make it the console by answering Y to this option.
+
endmenu
obj-$(CONFIG_SERIAL_PXA) += pxa.o
obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from many drivers using generic_serial interface.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ *
+ * Serial driver for BCM63xx integrated UART.
+ *
+ * Hardware flow control was _not_ tested since I only have RX/TX on
+ * my board.
+ */
+
+#if defined(CONFIG_SERIAL_BCM63XX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/console.h>
+#include <linux/clk.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/sysrq.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+
+#include <bcm63xx_clk.h>
+#include <bcm63xx_irq.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+
+#define BCM63XX_NR_UARTS 1
+
+static struct uart_port ports[BCM63XX_NR_UARTS];
+
+/*
+ * rx interrupt mask / stat
+ *
+ * mask:
+ * - rx fifo full
+ * - rx fifo above threshold
+ * - rx fifo not empty for too long
+ */
+#define UART_RX_INT_MASK (UART_IR_MASK(UART_IR_RXOVER) | \
+ UART_IR_MASK(UART_IR_RXTHRESH) | \
+ UART_IR_MASK(UART_IR_RXTIMEOUT))
+
+#define UART_RX_INT_STAT (UART_IR_STAT(UART_IR_RXOVER) | \
+ UART_IR_STAT(UART_IR_RXTHRESH) | \
+ UART_IR_STAT(UART_IR_RXTIMEOUT))
+
+/*
+ * tx interrupt mask / stat
+ *
+ * mask:
+ * - tx fifo empty
+ * - tx fifo below threshold
+ */
+#define UART_TX_INT_MASK (UART_IR_MASK(UART_IR_TXEMPTY) | \
+ UART_IR_MASK(UART_IR_TXTRESH))
+
+#define UART_TX_INT_STAT (UART_IR_STAT(UART_IR_TXEMPTY) | \
+ UART_IR_STAT(UART_IR_TXTRESH))
+
+/*
+ * external input interrupt
+ *
+ * mask: any edge on CTS, DCD
+ */
+#define UART_EXTINP_INT_MASK (UART_EXTINP_IRMASK(UART_EXTINP_IR_CTS) | \
+ UART_EXTINP_IRMASK(UART_EXTINP_IR_DCD))
+
+/*
+ * handy uart register accessor
+ */
+static inline unsigned int bcm_uart_readl(struct uart_port *port,
+ unsigned int offset)
+{
+ return bcm_readl(port->membase + offset);
+}
+
+static inline void bcm_uart_writel(struct uart_port *port,
+ unsigned int value, unsigned int offset)
+{
+ bcm_writel(value, port->membase + offset);
+}
+
+/*
+ * serial core request to check if uart tx fifo is empty
+ */
+static unsigned int bcm_uart_tx_empty(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ return (val & UART_IR_STAT(UART_IR_TXEMPTY)) ? 1 : 0;
+}
+
+/*
+ * serial core request to set RTS and DTR pin state and loopback mode
+ */
+static void bcm_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_MCTL_REG);
+ val &= ~(UART_MCTL_DTR_MASK | UART_MCTL_RTS_MASK);
+ /* invert of written value is reflected on the pin */
+ if (!(mctrl & TIOCM_DTR))
+ val |= UART_MCTL_DTR_MASK;
+ if (!(mctrl & TIOCM_RTS))
+ val |= UART_MCTL_RTS_MASK;
+ bcm_uart_writel(port, val, UART_MCTL_REG);
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ if (mctrl & TIOCM_LOOP)
+ val |= UART_CTL_LOOPBACK_MASK;
+ else
+ val &= ~UART_CTL_LOOPBACK_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * serial core request to return RI, CTS, DCD and DSR pin state
+ */
+static unsigned int bcm_uart_get_mctrl(struct uart_port *port)
+{
+ unsigned int val, mctrl;
+
+ mctrl = 0;
+ val = bcm_uart_readl(port, UART_EXTINP_REG);
+ if (val & UART_EXTINP_RI_MASK)
+ mctrl |= TIOCM_RI;
+ if (val & UART_EXTINP_CTS_MASK)
+ mctrl |= TIOCM_CTS;
+ if (val & UART_EXTINP_DCD_MASK)
+ mctrl |= TIOCM_CD;
+ if (val & UART_EXTINP_DSR_MASK)
+ mctrl |= TIOCM_DSR;
+ return mctrl;
+}
+
+/*
+ * serial core request to disable tx ASAP (used for flow control)
+ */
+static void bcm_uart_stop_tx(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val &= ~(UART_CTL_TXEN_MASK);
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val &= ~UART_TX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to (re)enable tx
+ */
+static void bcm_uart_start_tx(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val |= UART_TX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= UART_CTL_TXEN_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * serial core request to stop rx, called before port shutdown
+ */
+static void bcm_uart_stop_rx(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val &= ~UART_RX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to enable modem status interrupt reporting
+ */
+static void bcm_uart_enable_ms(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val |= UART_IR_MASK(UART_IR_EXTIP);
+ bcm_uart_writel(port, val, UART_IR_REG);
+}
+
+/*
+ * serial core request to start/stop emitting break char
+ */
+static void bcm_uart_break_ctl(struct uart_port *port, int ctl)
+{
+ unsigned long flags;
+ unsigned int val;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ if (ctl)
+ val |= UART_CTL_XMITBRK_MASK;
+ else
+ val &= ~UART_CTL_XMITBRK_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * return port type in string format
+ */
+static const char *bcm_uart_type(struct uart_port *port)
+{
+ return (port->type == PORT_BCM63XX) ? "bcm63xx_uart" : NULL;
+}
+
+/*
+ * read all chars in rx fifo and send them to core
+ */
+static void bcm_uart_do_rx(struct uart_port *port)
+{
+ struct tty_struct *tty;
+ unsigned int max_count;
+
+ /* limit number of char read in interrupt, should not be
+ * higher than fifo size anyway since we're much faster than
+ * serial port */
+ max_count = 32;
+ tty = port->info->port.tty;
+ do {
+ unsigned int iestat, c, cstat;
+ char flag;
+
+ /* get overrun/fifo empty information from ier
+ * register */
+ iestat = bcm_uart_readl(port, UART_IR_REG);
+ if (!(iestat & UART_IR_STAT(UART_IR_RXNOTEMPTY)))
+ break;
+
+ cstat = c = bcm_uart_readl(port, UART_FIFO_REG);
+ port->icount.rx++;
+ flag = TTY_NORMAL;
+ c &= 0xff;
+
+ if (unlikely((cstat & UART_FIFO_ANYERR_MASK))) {
+ /* do stats first */
+ if (cstat & UART_FIFO_BRKDET_MASK) {
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ continue;
+ }
+
+ if (cstat & UART_FIFO_PARERR_MASK)
+ port->icount.parity++;
+ if (cstat & UART_FIFO_FRAMEERR_MASK)
+ port->icount.frame++;
+
+ /* update flag wrt read_status_mask */
+ cstat &= port->read_status_mask;
+ if (cstat & UART_FIFO_BRKDET_MASK)
+ flag = TTY_BREAK;
+ if (cstat & UART_FIFO_FRAMEERR_MASK)
+ flag = TTY_FRAME;
+ if (cstat & UART_FIFO_PARERR_MASK)
+ flag = TTY_PARITY;
+ }
+
+ if (uart_handle_sysrq_char(port, c))
+ continue;
+
+ if (unlikely(iestat & UART_IR_STAT(UART_IR_RXOVER))) {
+ port->icount.overrun++;
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ }
+
+ if ((cstat & port->ignore_status_mask) == 0)
+ tty_insert_flip_char(tty, c, flag);
+
+ } while (--max_count);
+
+ tty_flip_buffer_push(tty);
+}
+
+/*
+ * fill tx fifo with chars to send, stop when fifo is about to be full
+ * or when all chars have been sent.
+ */
+static void bcm_uart_do_tx(struct uart_port *port)
+{
+ struct circ_buf *xmit;
+ unsigned int val, max_count;
+
+ if (port->x_char) {
+ bcm_uart_writel(port, port->x_char, UART_FIFO_REG);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if (uart_tx_stopped(port)) {
+ bcm_uart_stop_tx(port);
+ return;
+ }
+
+ xmit = &port->info->xmit;
+ if (uart_circ_empty(xmit))
+ goto txq_empty;
+
+ val = bcm_uart_readl(port, UART_MCTL_REG);
+ val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT;
+ max_count = port->fifosize - val;
+
+ while (max_count--) {
+ unsigned int c;
+
+ c = xmit->buf[xmit->tail];
+ bcm_uart_writel(port, c, UART_FIFO_REG);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ goto txq_empty;
+ return;
+
+txq_empty:
+ /* nothing to send, disable transmit interrupt */
+ val = bcm_uart_readl(port, UART_IR_REG);
+ val &= ~UART_TX_INT_MASK;
+ bcm_uart_writel(port, val, UART_IR_REG);
+ return;
+}
+
+/*
+ * process uart interrupt
+ */
+static irqreturn_t bcm_uart_interrupt(int irq, void *dev_id)
+{
+ struct uart_port *port;
+ unsigned int irqstat;
+
+ port = dev_id;
+ spin_lock(&port->lock);
+
+ irqstat = bcm_uart_readl(port, UART_IR_REG);
+ if (irqstat & UART_RX_INT_STAT)
+ bcm_uart_do_rx(port);
+
+ if (irqstat & UART_TX_INT_STAT)
+ bcm_uart_do_tx(port);
+
+ if (irqstat & UART_IR_MASK(UART_IR_EXTIP)) {
+ unsigned int estat;
+
+ estat = bcm_uart_readl(port, UART_EXTINP_REG);
+ if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_CTS))
+ uart_handle_cts_change(port,
+ estat & UART_EXTINP_CTS_MASK);
+ if (estat & UART_EXTINP_IRSTAT(UART_EXTINP_IR_DCD))
+ uart_handle_dcd_change(port,
+ estat & UART_EXTINP_DCD_MASK);
+ }
+
+ spin_unlock(&port->lock);
+ return IRQ_HANDLED;
+}
+
+/*
+ * enable rx & tx operation on uart
+ */
+static void bcm_uart_enable(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= (UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK | UART_CTL_RXEN_MASK);
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * disable rx & tx operation on uart
+ */
+static void bcm_uart_disable(struct uart_port *port)
+{
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val &= ~(UART_CTL_BRGEN_MASK | UART_CTL_TXEN_MASK |
+ UART_CTL_RXEN_MASK);
+ bcm_uart_writel(port, val, UART_CTL_REG);
+}
+
+/*
+ * clear all unread data in rx fifo and unsent data in tx fifo
+ */
+static void bcm_uart_flush(struct uart_port *port)
+{
+ unsigned int val;
+
+ /* empty rx and tx fifo */
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val |= UART_CTL_RSTRXFIFO_MASK | UART_CTL_RSTTXFIFO_MASK;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ /* read any pending char to make sure all irq status are
+ * cleared */
+ (void)bcm_uart_readl(port, UART_FIFO_REG);
+}
+
+/*
+ * serial core request to initialize uart and start rx operation
+ */
+static int bcm_uart_startup(struct uart_port *port)
+{
+ unsigned int val;
+ int ret;
+
+ /* mask all irq and flush port */
+ bcm_uart_disable(port);
+ bcm_uart_writel(port, 0, UART_IR_REG);
+ bcm_uart_flush(port);
+
+ /* clear any pending external input interrupt */
+ (void)bcm_uart_readl(port, UART_EXTINP_REG);
+
+ /* set rx/tx fifo thresh to fifo half size */
+ val = bcm_uart_readl(port, UART_MCTL_REG);
+ val &= ~(UART_MCTL_RXFIFOTHRESH_MASK | UART_MCTL_TXFIFOTHRESH_MASK);
+ val |= (port->fifosize / 2) << UART_MCTL_RXFIFOTHRESH_SHIFT;
+ val |= (port->fifosize / 2) << UART_MCTL_TXFIFOTHRESH_SHIFT;
+ bcm_uart_writel(port, val, UART_MCTL_REG);
+
+ /* set rx fifo timeout to 1 char time */
+ val = bcm_uart_readl(port, UART_CTL_REG);
+ val &= ~UART_CTL_RXTMOUTCNT_MASK;
+ val |= 1 << UART_CTL_RXTMOUTCNT_SHIFT;
+ bcm_uart_writel(port, val, UART_CTL_REG);
+
+ /* report any edge on dcd and cts */
+ val = UART_EXTINP_INT_MASK;
+ val |= UART_EXTINP_DCD_NOSENSE_MASK;
+ val |= UART_EXTINP_CTS_NOSENSE_MASK;
+ bcm_uart_writel(port, val, UART_EXTINP_REG);
+
+ /* register irq and enable rx interrupts */
+ ret = request_irq(port->irq, bcm_uart_interrupt, 0,
+ bcm_uart_type(port), port);
+ if (ret)
+ return ret;
+ bcm_uart_writel(port, UART_RX_INT_MASK, UART_IR_REG);
+ bcm_uart_enable(port);
+ return 0;
+}
+
+/*
+ * serial core request to flush & disable uart
+ */
+static void bcm_uart_shutdown(struct uart_port *port)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ bcm_uart_writel(port, 0, UART_IR_REG);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ bcm_uart_disable(port);
+ bcm_uart_flush(port);
+ free_irq(port->irq, port);
+}
+
+/*
+ * serial core request to change current uart setting
+ */
+static void bcm_uart_set_termios(struct uart_port *port,
+ struct ktermios *new,
+ struct ktermios *old)
+{
+ unsigned int ctl, baud, quot, ier;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ /* disable uart while changing speed */
+ bcm_uart_disable(port);
+ bcm_uart_flush(port);
+
+ /* update Control register */
+ ctl = bcm_uart_readl(port, UART_CTL_REG);
+ ctl &= ~UART_CTL_BITSPERSYM_MASK;
+
+ switch (new->c_cflag & CSIZE) {
+ case CS5:
+ ctl |= (0 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ case CS6:
+ ctl |= (1 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ case CS7:
+ ctl |= (2 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ default:
+ ctl |= (3 << UART_CTL_BITSPERSYM_SHIFT);
+ break;
+ }
+
+ ctl &= ~UART_CTL_STOPBITS_MASK;
+ if (new->c_cflag & CSTOPB)
+ ctl |= UART_CTL_STOPBITS_2;
+ else
+ ctl |= UART_CTL_STOPBITS_1;
+
+ ctl &= ~(UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
+ if (new->c_cflag & PARENB)
+ ctl |= (UART_CTL_RXPAREN_MASK | UART_CTL_TXPAREN_MASK);
+ ctl &= ~(UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
+ if (new->c_cflag & PARODD)
+ ctl |= (UART_CTL_RXPAREVEN_MASK | UART_CTL_TXPAREVEN_MASK);
+ bcm_uart_writel(port, ctl, UART_CTL_REG);
+
+ /* update Baudword register */
+ baud = uart_get_baud_rate(port, new, old, 0, port->uartclk / 16);
+ quot = uart_get_divisor(port, baud) - 1;
+ bcm_uart_writel(port, quot, UART_BAUD_REG);
+
+ /* update Interrupt register */
+ ier = bcm_uart_readl(port, UART_IR_REG);
+
+ ier &= ~UART_IR_MASK(UART_IR_EXTIP);
+ if (UART_ENABLE_MS(port, new->c_cflag))
+ ier |= UART_IR_MASK(UART_IR_EXTIP);
+
+ bcm_uart_writel(port, ier, UART_IR_REG);
+
+ /* update read/ignore mask */
+ port->read_status_mask = UART_FIFO_VALID_MASK;
+ if (new->c_iflag & INPCK) {
+ port->read_status_mask |= UART_FIFO_FRAMEERR_MASK;
+ port->read_status_mask |= UART_FIFO_PARERR_MASK;
+ }
+ if (new->c_iflag & (BRKINT))
+ port->read_status_mask |= UART_FIFO_BRKDET_MASK;
+
+ port->ignore_status_mask = 0;
+ if (new->c_iflag & IGNPAR)
+ port->ignore_status_mask |= UART_FIFO_PARERR_MASK;
+ if (new->c_iflag & IGNBRK)
+ port->ignore_status_mask |= UART_FIFO_BRKDET_MASK;
+ if (!(new->c_cflag & CREAD))
+ port->ignore_status_mask |= UART_FIFO_VALID_MASK;
+
+ uart_update_timeout(port, new->c_cflag, baud);
+ bcm_uart_enable(port);
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/*
+ * serial core request to claim uart iomem
+ */
+static int bcm_uart_request_port(struct uart_port *port)
+{
+ unsigned int size;
+
+ size = RSET_UART_SIZE;
+ if (!request_mem_region(port->mapbase, size, "bcm63xx")) {
+ dev_err(port->dev, "Memory region busy\n");
+ return -EBUSY;
+ }
+
+ port->membase = ioremap(port->mapbase, size);
+ if (!port->membase) {
+ dev_err(port->dev, "Unable to map registers\n");
+ release_mem_region(port->mapbase, size);
+ return -EBUSY;
+ }
+ return 0;
+}
+
+/*
+ * serial core request to release uart iomem
+ */
+static void bcm_uart_release_port(struct uart_port *port)
+{
+ release_mem_region(port->mapbase, RSET_UART_SIZE);
+ iounmap(port->membase);
+}
+
+/*
+ * serial core request to do any port required autoconfiguration
+ */
+static void bcm_uart_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ if (bcm_uart_request_port(port))
+ return;
+ port->type = PORT_BCM63XX;
+ }
+}
+
+/*
+ * serial core request to check that port information in serinfo are
+ * suitable
+ */
+static int bcm_uart_verify_port(struct uart_port *port,
+ struct serial_struct *serinfo)
+{
+ if (port->type != PORT_BCM63XX)
+ return -EINVAL;
+ if (port->irq != serinfo->irq)
+ return -EINVAL;
+ if (port->iotype != serinfo->io_type)
+ return -EINVAL;
+ if (port->mapbase != (unsigned long)serinfo->iomem_base)
+ return -EINVAL;
+ return 0;
+}
+
+/* serial core callbacks */
+static struct uart_ops bcm_uart_ops = {
+ .tx_empty = bcm_uart_tx_empty,
+ .get_mctrl = bcm_uart_get_mctrl,
+ .set_mctrl = bcm_uart_set_mctrl,
+ .start_tx = bcm_uart_start_tx,
+ .stop_tx = bcm_uart_stop_tx,
+ .stop_rx = bcm_uart_stop_rx,
+ .enable_ms = bcm_uart_enable_ms,
+ .break_ctl = bcm_uart_break_ctl,
+ .startup = bcm_uart_startup,
+ .shutdown = bcm_uart_shutdown,
+ .set_termios = bcm_uart_set_termios,
+ .type = bcm_uart_type,
+ .release_port = bcm_uart_release_port,
+ .request_port = bcm_uart_request_port,
+ .config_port = bcm_uart_config_port,
+ .verify_port = bcm_uart_verify_port,
+};
+
+
+
+#ifdef CONFIG_SERIAL_BCM63XX_CONSOLE
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+ unsigned int tmout;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ tmout = 10000;
+ while (--tmout) {
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_IR_REG);
+ if (val & UART_IR_STAT(UART_IR_TXEMPTY))
+ break;
+ udelay(1);
+ }
+
+ /* Wait up to 1s for flow control if necessary */
+ if (port->flags & UPF_CONS_FLOW) {
+ tmout = 1000000;
+ while (--tmout) {
+ unsigned int val;
+
+ val = bcm_uart_readl(port, UART_EXTINP_REG);
+ if (val & UART_EXTINP_CTS_MASK)
+ break;
+ udelay(1);
+ }
+ }
+}
+
+/*
+ * output given char
+ */
+static void bcm_console_putchar(struct uart_port *port, int ch)
+{
+ wait_for_xmitr(port);
+ bcm_uart_writel(port, ch, UART_FIFO_REG);
+}
+
+/*
+ * console core request to output given string
+ */
+static void bcm_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct uart_port *port;
+ unsigned long flags;
+ int locked;
+
+ port = &ports[co->index];
+
+ local_irq_save(flags);
+ if (port->sysrq) {
+ /* bcm_uart_interrupt() already took the lock */
+ locked = 0;
+ } else if (oops_in_progress) {
+ locked = spin_trylock(&port->lock);
+ } else {
+ spin_lock(&port->lock);
+ locked = 1;
+ }
+
+ /* call helper to deal with \r\n */
+ uart_console_write(port, s, count, bcm_console_putchar);
+
+ /* and wait for char to be transmitted */
+ wait_for_xmitr(port);
+
+ if (locked)
+ spin_unlock(&port->lock);
+ local_irq_restore(flags);
+}
+
+/*
+ * console core request to setup given console, find matching uart
+ * port and setup it.
+ */
+static int bcm_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index < 0 || co->index >= BCM63XX_NR_UARTS)
+ return -EINVAL;
+ port = &ports[co->index];
+ if (!port->membase)
+ return -ENODEV;
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver bcm_uart_driver;
+
+static struct console bcm63xx_console = {
+ .name = "ttyS",
+ .write = bcm_console_write,
+ .device = uart_console_device,
+ .setup = bcm_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &bcm_uart_driver,
+};
+
+static int __init bcm63xx_console_init(void)
+{
+ register_console(&bcm63xx_console);
+ return 0;
+}
+
+console_initcall(bcm63xx_console_init);
+
+#define BCM63XX_CONSOLE (&bcm63xx_console)
+#else
+#define BCM63XX_CONSOLE NULL
+#endif /* CONFIG_SERIAL_BCM63XX_CONSOLE */
+
+static struct uart_driver bcm_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "bcm63xx_uart",
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = 1,
+ .cons = BCM63XX_CONSOLE,
+};
+
+/*
+ * platform driver probe/remove callback
+ */
+static int __devinit bcm_uart_probe(struct platform_device *pdev)
+{
+ struct resource *res_mem, *res_irq;
+ struct uart_port *port;
+ struct clk *clk;
+ int ret;
+
+ if (pdev->id < 0 || pdev->id >= BCM63XX_NR_UARTS)
+ return -EINVAL;
+
+ if (ports[pdev->id].membase)
+ return -EBUSY;
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (!res_irq)
+ return -ENODEV;
+
+ clk = clk_get(&pdev->dev, "periph");
+ if (IS_ERR(clk))
+ return -ENODEV;
+
+ port = &ports[pdev->id];
+ memset(port, 0, sizeof(*port));
+ port->iotype = UPIO_MEM;
+ port->mapbase = res_mem->start;
+ port->irq = res_irq->start;
+ port->ops = &bcm_uart_ops;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->dev = &pdev->dev;
+ port->fifosize = 16;
+ port->uartclk = clk_get_rate(clk) / 2;
+ clk_put(clk);
+
+ ret = uart_add_one_port(&bcm_uart_driver, port);
+ if (ret) {
+ kfree(port);
+ return ret;
+ }
+ platform_set_drvdata(pdev, port);
+ return 0;
+}
+
+static int __devexit bcm_uart_remove(struct platform_device *pdev)
+{
+ struct uart_port *port;
+
+ port = platform_get_drvdata(pdev);
+ uart_remove_one_port(&bcm_uart_driver, port);
+ platform_set_drvdata(pdev, NULL);
+ /* mark port as free */
+ ports[pdev->id].membase = 0;
+ return 0;
+}
+
+/*
+ * platform driver stuff
+ */
+static struct platform_driver bcm_uart_platform_driver = {
+ .probe = bcm_uart_probe,
+ .remove = __devexit_p(bcm_uart_remove),
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "bcm63xx_uart",
+ },
+};
+
+static int __init bcm_uart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&bcm_uart_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&bcm_uart_platform_driver);
+ if (ret)
+ uart_unregister_driver(&bcm_uart_driver);
+
+ return ret;
+}
+
+static void __exit bcm_uart_exit(void)
+{
+ platform_driver_unregister(&bcm_uart_platform_driver);
+ uart_unregister_driver(&bcm_uart_driver);
+}
+
+module_init(bcm_uart_init);
+module_exit(bcm_uart_exit);
+
+MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>");
+MODULE_DESCRIPTION("Broadcom 63<xx integrated uart driver");
+MODULE_LICENSE("GPL");
u8 *p;
int count;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
- struct circ_buf *xmit = &port->info->xmit;
+ struct circ_buf *xmit = &port->state->xmit;
/* Handle xon/xoff */
if (port->x_char) {
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/major.h>
+#include <linux/smp_lock.h>
#include <linux/string.h>
#include <linux/fcntl.h>
#include <linux/mm.h>
if (port < 4) {
temp = readl(stop_proc[port].global_control_reg);
temp =
- (temp & ~start_proc[port].processor_id) | stop_proc[port].processor_id;
+ (temp & ~start_proc[port].processor_id) | stop_proc[port].processor_id;
writel(temp, stop_proc[port].global_control_reg);
/* write flush */
if (port < 4) {
temp = readl(start_proc[port].global_control_reg);
temp =
- (temp & ~stop_proc[port].processor_id) | start_proc[port].processor_id;
+ (temp & ~stop_proc[port].processor_id) | start_proc[port].processor_id;
writel(temp, start_proc[port].global_control_reg);
/* write flush */
dev_err(&icom_port->adapter->pci_dev->dev,"Port not opertional\n");
}
- if (new_page != NULL)
- pci_free_consistent(dev, 4096, new_page, temp_pci);
+ if (new_page != NULL)
+ pci_free_consistent(dev, 4096, new_page, temp_pci);
}
static int startup(struct icom_port *icom_port)
const struct pci_device_id *ent)
{
int index;
- unsigned int command_reg;
- int retval;
- struct icom_adapter *icom_adapter;
- struct icom_port *icom_port;
+ unsigned int command_reg;
+ int retval;
+ struct icom_adapter *icom_adapter;
+ struct icom_port *icom_port;
- retval = pci_enable_device(dev);
- if (retval) {
+ retval = pci_enable_device(dev);
+ if (retval) {
dev_err(&dev->dev, "Device enable FAILED\n");
- return retval;
+ return retval;
}
if ( (retval = pci_request_regions(dev, "icom"))) {
return retval;
}
- pci_set_master(dev);
+ pci_set_master(dev);
- if ( (retval = pci_read_config_dword(dev, PCI_COMMAND, &command_reg))) {
+ if ( (retval = pci_read_config_dword(dev, PCI_COMMAND, &command_reg))) {
dev_err(&dev->dev, "PCI Config read FAILED\n");
- return retval;
- }
+ return retval;
+ }
pci_write_config_dword(dev, PCI_COMMAND,
command_reg | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
| PCI_COMMAND_PARITY | PCI_COMMAND_SERR);
- if (ent->driver_data == ADAPTER_V1) {
+ if (ent->driver_data == ADAPTER_V1) {
pci_write_config_dword(dev, 0x44, 0x8300830A);
- } else {
+ } else {
pci_write_config_dword(dev, 0x44, 0x42004200);
pci_write_config_dword(dev, 0x48, 0x42004200);
- }
+ }
retval = icom_alloc_adapter(&icom_adapter);
goto probe_exit0;
}
- icom_adapter->base_addr_pci = pci_resource_start(dev, 0);
- icom_adapter->pci_dev = dev;
- icom_adapter->version = ent->driver_data;
- icom_adapter->subsystem_id = ent->subdevice;
+ icom_adapter->base_addr_pci = pci_resource_start(dev, 0);
+ icom_adapter->pci_dev = dev;
+ icom_adapter->version = ent->driver_data;
+ icom_adapter->subsystem_id = ent->subdevice;
retval = icom_init_ports(icom_adapter);
goto probe_exit1;
}
- icom_adapter->base_addr = pci_ioremap_bar(dev, 0);
+ icom_adapter->base_addr = pci_ioremap_bar(dev, 0);
if (!icom_adapter->base_addr)
goto probe_exit1;
retval = icom_load_ports(icom_adapter);
- for (index = 0; index < icom_adapter->numb_ports; index++) {
+ for (index = 0; index < icom_adapter->numb_ports; index++) {
icom_port = &icom_adapter->port_info[index];
if (icom_port->status == ICOM_PORT_ACTIVE) {
icom_port->status = ICOM_PORT_OFF;
dev_err(&dev->dev, "Device add failed\n");
} else
- dev_info(&dev->dev, "Device added\n");
+ dev_info(&dev->dev, "Device added\n");
}
}
pci_release_regions(dev);
pci_disable_device(dev);
- return retval;
-
-
+ return retval;
}
static void __devexit icom_remove(struct pci_dev *dev)
.cons = PXA_CONSOLE,
};
-static int serial_pxa_suspend(struct platform_device *dev, pm_message_t state)
+#ifdef CONFIG_PM
+static int serial_pxa_suspend(struct device *dev)
{
- struct uart_pxa_port *sport = platform_get_drvdata(dev);
+ struct uart_pxa_port *sport = dev_get_drvdata(dev);
if (sport)
uart_suspend_port(&serial_pxa_reg, &sport->port);
return 0;
}
-static int serial_pxa_resume(struct platform_device *dev)
+static int serial_pxa_resume(struct device *dev)
{
- struct uart_pxa_port *sport = platform_get_drvdata(dev);
+ struct uart_pxa_port *sport = dev_get_drvdata(dev);
if (sport)
uart_resume_port(&serial_pxa_reg, &sport->port);
return 0;
}
+static struct dev_pm_ops serial_pxa_pm_ops = {
+ .suspend = serial_pxa_suspend,
+ .resume = serial_pxa_resume,
+};
+#endif
+
static int serial_pxa_probe(struct platform_device *dev)
{
struct uart_pxa_port *sport;
.probe = serial_pxa_probe,
.remove = serial_pxa_remove,
- .suspend = serial_pxa_suspend,
- .resume = serial_pxa_resume,
.driver = {
.name = "pxa2xx-uart",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &serial_pxa_pm_ops,
+#endif
},
};
PPSR |= PPC_TXD1 | PPC_TXD3;
}
-void __init sa1100_register_uart_fns(struct sa1100_port_fns *fns)
+void __devinit sa1100_register_uart_fns(struct sa1100_port_fns *fns)
{
if (fns->get_mctrl)
sa1100_pops.get_mctrl = fns->get_mctrl;
sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
}
+static struct uart_txx9_port *to_uart_txx9_port(struct uart_port *port)
+{
+ return container_of(port, struct uart_txx9_port, port);
+}
+
static void serial_txx9_stop_tx(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
}
static void serial_txx9_start_tx(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
}
static void serial_txx9_stop_rx(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
up->port.read_status_mask &= ~TXX9_SIDISR_RDIS;
}
static void serial_txx9_initialize(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned int tmout = 10000;
sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
static unsigned int serial_txx9_tx_empty(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned long flags;
unsigned int ret;
static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned int ret;
/* no modem control lines */
static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
if (mctrl & TIOCM_RTS)
sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
static void serial_txx9_break_ctl(struct uart_port *port, int break_state)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned long flags;
spin_lock_irqsave(&up->port.lock, flags);
{
unsigned int ier;
unsigned char c;
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
/*
* First save the IER then disable the interrupts
static void serial_txx9_put_poll_char(struct uart_port *port, unsigned char c)
{
unsigned int ier;
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
/*
* First save the IER then disable the interrupts
static int serial_txx9_startup(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned long flags;
int retval;
static void serial_txx9_shutdown(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned long flags;
/*
serial_txx9_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
unsigned int cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
static void serial_txx9_release_port(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
serial_txx9_release_resource(up);
}
static int serial_txx9_request_port(struct uart_port *port)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
return serial_txx9_request_resource(up);
}
static void serial_txx9_config_port(struct uart_port *port, int uflags)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
int ret;
/*
static void serial_txx9_console_putchar(struct uart_port *port, int ch)
{
- struct uart_txx9_port *up = (struct uart_txx9_port *)port;
+ struct uart_txx9_port *up = to_uart_txx9_port(port);
wait_for_xmitr(up);
sio_out(up, TXX9_SITFIFO, ch);
*/
static u32 sfi_use_ioremap __read_mostly;
-static void __iomem *sfi_map_memory(u64 phys, u32 size)
+/*
+ * sfi_un/map_memory calls early_ioremap/iounmap which is a __init function
+ * and introduces section mismatch. So use __ref to make it calm.
+ */
+static void __iomem * __ref sfi_map_memory(u64 phys, u32 size)
{
if (!phys || !size)
return NULL;
return early_ioremap(phys, size);
}
-static void sfi_unmap_memory(void __iomem *virt, u32 size)
+static void __ref sfi_unmap_memory(void __iomem *virt, u32 size)
{
if (!virt || !size)
return;
* sfi_verify_table()
* Sanity check table lengh, calculate checksum
*/
-static __init int sfi_verify_table(struct sfi_table_header *table)
+static int sfi_verify_table(struct sfi_table_header *table)
{
u8 checksum = 0;
* the mapped virt address will be returned, and the virt space
* will be released by call sfi_put_table() later
*
+ * This two cases are from two different functions with two different
+ * sections and causes section mismatch warning. So use __ref to tell
+ * modpost not to make any noise.
+ *
* Return value:
* NULL: when can't find a table matching the key
* ERR_PTR(error): error value
* virt table address: when a matched table is found
*/
-struct sfi_table_header *sfi_check_table(u64 pa, struct sfi_table_key *key)
+struct sfi_table_header *
+ __ref sfi_check_table(u64 pa, struct sfi_table_key *key)
{
struct sfi_table_header *th;
void *ret = NULL;
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
obj-$(CONFIG_SPI_GPIO) += spi_gpio.o
-obj-$(CONFIG_SPI_IMX) += mxc_spi.o
+obj-$(CONFIG_SPI_IMX) += spi_imx.o
obj-$(CONFIG_SPI_LM70_LLP) += spi_lm70llp.o
obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += omap_uwire.o
GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS, 0) | \
GEN_MASK_BITS(SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, SSP_CR0_MASK_HALFDUP, 5) | \
GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \
- GEN_MASK_BITS(SSP_CLK_FALLING_EDGE, SSP_CR0_MASK_SPH, 7) | \
+ GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \
GEN_MASK_BITS(NMDK_SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) | \
GEN_MASK_BITS(SSP_BITS_8, SSP_CR0_MASK_CSS, 16) | \
GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF, 21) \
return -EINVAL;
}
if (chip_info->iface == SSP_INTERFACE_MOTOROLA_SPI) {
- if ((chip_info->clk_phase != SSP_CLK_RISING_EDGE)
- && (chip_info->clk_phase != SSP_CLK_FALLING_EDGE)) {
+ if ((chip_info->clk_phase != SSP_CLK_FIRST_EDGE)
+ && (chip_info->clk_phase != SSP_CLK_SECOND_EDGE)) {
dev_err(chip_info->dev,
"Clock Phase is configured incorrectly\n");
return -EINVAL;
chip_info->data_size = SSP_DATA_BITS_12;
chip_info->rx_lev_trig = SSP_RX_1_OR_MORE_ELEM;
chip_info->tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC;
- chip_info->clk_phase = SSP_CLK_FALLING_EDGE;
+ chip_info->clk_phase = SSP_CLK_SECOND_EDGE;
chip_info->clk_pol = SSP_CLK_POL_IDLE_LOW;
chip_info->ctrl_len = SSP_BITS_8;
chip_info->wait_state = SSP_MWIRE_WAIT_ZERO;
+++ /dev/null
-/*
- * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright (C) 2008 Juergen Beisert
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the
- * Free Software Foundation
- * 51 Franklin Street, Fifth Floor
- * Boston, MA 02110-1301, USA.
- */
-
-#include <linux/clk.h>
-#include <linux/completion.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
-#include <linux/types.h>
-
-#include <mach/spi.h>
-
-#define DRIVER_NAME "spi_imx"
-
-#define MXC_CSPIRXDATA 0x00
-#define MXC_CSPITXDATA 0x04
-#define MXC_CSPICTRL 0x08
-#define MXC_CSPIINT 0x0c
-#define MXC_RESET 0x1c
-
-/* generic defines to abstract from the different register layouts */
-#define MXC_INT_RR (1 << 0) /* Receive data ready interrupt */
-#define MXC_INT_TE (1 << 1) /* Transmit FIFO empty interrupt */
-
-struct mxc_spi_config {
- unsigned int speed_hz;
- unsigned int bpw;
- unsigned int mode;
- int cs;
-};
-
-struct mxc_spi_data {
- struct spi_bitbang bitbang;
-
- struct completion xfer_done;
- void *base;
- int irq;
- struct clk *clk;
- unsigned long spi_clk;
- int *chipselect;
-
- unsigned int count;
- void (*tx)(struct mxc_spi_data *);
- void (*rx)(struct mxc_spi_data *);
- void *rx_buf;
- const void *tx_buf;
- unsigned int txfifo; /* number of words pushed in tx FIFO */
-
- /* SoC specific functions */
- void (*intctrl)(struct mxc_spi_data *, int);
- int (*config)(struct mxc_spi_data *, struct mxc_spi_config *);
- void (*trigger)(struct mxc_spi_data *);
- int (*rx_available)(struct mxc_spi_data *);
-};
-
-#define MXC_SPI_BUF_RX(type) \
-static void mxc_spi_buf_rx_##type(struct mxc_spi_data *mxc_spi) \
-{ \
- unsigned int val = readl(mxc_spi->base + MXC_CSPIRXDATA); \
- \
- if (mxc_spi->rx_buf) { \
- *(type *)mxc_spi->rx_buf = val; \
- mxc_spi->rx_buf += sizeof(type); \
- } \
-}
-
-#define MXC_SPI_BUF_TX(type) \
-static void mxc_spi_buf_tx_##type(struct mxc_spi_data *mxc_spi) \
-{ \
- type val = 0; \
- \
- if (mxc_spi->tx_buf) { \
- val = *(type *)mxc_spi->tx_buf; \
- mxc_spi->tx_buf += sizeof(type); \
- } \
- \
- mxc_spi->count -= sizeof(type); \
- \
- writel(val, mxc_spi->base + MXC_CSPITXDATA); \
-}
-
-MXC_SPI_BUF_RX(u8)
-MXC_SPI_BUF_TX(u8)
-MXC_SPI_BUF_RX(u16)
-MXC_SPI_BUF_TX(u16)
-MXC_SPI_BUF_RX(u32)
-MXC_SPI_BUF_TX(u32)
-
-/* First entry is reserved, second entry is valid only if SDHC_SPIEN is set
- * (which is currently not the case in this driver)
- */
-static int mxc_clkdivs[] = {0, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96, 128, 192,
- 256, 384, 512, 768, 1024};
-
-/* MX21, MX27 */
-static unsigned int mxc_spi_clkdiv_1(unsigned int fin,
- unsigned int fspi)
-{
- int i, max;
-
- if (cpu_is_mx21())
- max = 18;
- else
- max = 16;
-
- for (i = 2; i < max; i++)
- if (fspi * mxc_clkdivs[i] >= fin)
- return i;
-
- return max;
-}
-
-/* MX1, MX31, MX35 */
-static unsigned int mxc_spi_clkdiv_2(unsigned int fin,
- unsigned int fspi)
-{
- int i, div = 4;
-
- for (i = 0; i < 7; i++) {
- if (fspi * div >= fin)
- return i;
- div <<= 1;
- }
-
- return 7;
-}
-
-#define MX31_INTREG_TEEN (1 << 0)
-#define MX31_INTREG_RREN (1 << 3)
-
-#define MX31_CSPICTRL_ENABLE (1 << 0)
-#define MX31_CSPICTRL_MASTER (1 << 1)
-#define MX31_CSPICTRL_XCH (1 << 2)
-#define MX31_CSPICTRL_POL (1 << 4)
-#define MX31_CSPICTRL_PHA (1 << 5)
-#define MX31_CSPICTRL_SSCTL (1 << 6)
-#define MX31_CSPICTRL_SSPOL (1 << 7)
-#define MX31_CSPICTRL_BC_SHIFT 8
-#define MX35_CSPICTRL_BL_SHIFT 20
-#define MX31_CSPICTRL_CS_SHIFT 24
-#define MX35_CSPICTRL_CS_SHIFT 12
-#define MX31_CSPICTRL_DR_SHIFT 16
-
-#define MX31_CSPISTATUS 0x14
-#define MX31_STATUS_RR (1 << 3)
-
-/* These functions also work for the i.MX35, but be aware that
- * the i.MX35 has a slightly different register layout for bits
- * we do not use here.
- */
-static void mx31_intctrl(struct mxc_spi_data *mxc_spi, int enable)
-{
- unsigned int val = 0;
-
- if (enable & MXC_INT_TE)
- val |= MX31_INTREG_TEEN;
- if (enable & MXC_INT_RR)
- val |= MX31_INTREG_RREN;
-
- writel(val, mxc_spi->base + MXC_CSPIINT);
-}
-
-static void mx31_trigger(struct mxc_spi_data *mxc_spi)
-{
- unsigned int reg;
-
- reg = readl(mxc_spi->base + MXC_CSPICTRL);
- reg |= MX31_CSPICTRL_XCH;
- writel(reg, mxc_spi->base + MXC_CSPICTRL);
-}
-
-static int mx31_config(struct mxc_spi_data *mxc_spi,
- struct mxc_spi_config *config)
-{
- unsigned int reg = MX31_CSPICTRL_ENABLE | MX31_CSPICTRL_MASTER;
-
- reg |= mxc_spi_clkdiv_2(mxc_spi->spi_clk, config->speed_hz) <<
- MX31_CSPICTRL_DR_SHIFT;
-
- if (cpu_is_mx31())
- reg |= (config->bpw - 1) << MX31_CSPICTRL_BC_SHIFT;
- else if (cpu_is_mx35()) {
- reg |= (config->bpw - 1) << MX35_CSPICTRL_BL_SHIFT;
- reg |= MX31_CSPICTRL_SSCTL;
- }
-
- if (config->mode & SPI_CPHA)
- reg |= MX31_CSPICTRL_PHA;
- if (config->mode & SPI_CPOL)
- reg |= MX31_CSPICTRL_POL;
- if (config->mode & SPI_CS_HIGH)
- reg |= MX31_CSPICTRL_SSPOL;
- if (config->cs < 0) {
- if (cpu_is_mx31())
- reg |= (config->cs + 32) << MX31_CSPICTRL_CS_SHIFT;
- else if (cpu_is_mx35())
- reg |= (config->cs + 32) << MX35_CSPICTRL_CS_SHIFT;
- }
-
- writel(reg, mxc_spi->base + MXC_CSPICTRL);
-
- return 0;
-}
-
-static int mx31_rx_available(struct mxc_spi_data *mxc_spi)
-{
- return readl(mxc_spi->base + MX31_CSPISTATUS) & MX31_STATUS_RR;
-}
-
-#define MX27_INTREG_RR (1 << 4)
-#define MX27_INTREG_TEEN (1 << 9)
-#define MX27_INTREG_RREN (1 << 13)
-
-#define MX27_CSPICTRL_POL (1 << 5)
-#define MX27_CSPICTRL_PHA (1 << 6)
-#define MX27_CSPICTRL_SSPOL (1 << 8)
-#define MX27_CSPICTRL_XCH (1 << 9)
-#define MX27_CSPICTRL_ENABLE (1 << 10)
-#define MX27_CSPICTRL_MASTER (1 << 11)
-#define MX27_CSPICTRL_DR_SHIFT 14
-#define MX27_CSPICTRL_CS_SHIFT 19
-
-static void mx27_intctrl(struct mxc_spi_data *mxc_spi, int enable)
-{
- unsigned int val = 0;
-
- if (enable & MXC_INT_TE)
- val |= MX27_INTREG_TEEN;
- if (enable & MXC_INT_RR)
- val |= MX27_INTREG_RREN;
-
- writel(val, mxc_spi->base + MXC_CSPIINT);
-}
-
-static void mx27_trigger(struct mxc_spi_data *mxc_spi)
-{
- unsigned int reg;
-
- reg = readl(mxc_spi->base + MXC_CSPICTRL);
- reg |= MX27_CSPICTRL_XCH;
- writel(reg, mxc_spi->base + MXC_CSPICTRL);
-}
-
-static int mx27_config(struct mxc_spi_data *mxc_spi,
- struct mxc_spi_config *config)
-{
- unsigned int reg = MX27_CSPICTRL_ENABLE | MX27_CSPICTRL_MASTER;
-
- reg |= mxc_spi_clkdiv_1(mxc_spi->spi_clk, config->speed_hz) <<
- MX27_CSPICTRL_DR_SHIFT;
- reg |= config->bpw - 1;
-
- if (config->mode & SPI_CPHA)
- reg |= MX27_CSPICTRL_PHA;
- if (config->mode & SPI_CPOL)
- reg |= MX27_CSPICTRL_POL;
- if (config->mode & SPI_CS_HIGH)
- reg |= MX27_CSPICTRL_SSPOL;
- if (config->cs < 0)
- reg |= (config->cs + 32) << MX27_CSPICTRL_CS_SHIFT;
-
- writel(reg, mxc_spi->base + MXC_CSPICTRL);
-
- return 0;
-}
-
-static int mx27_rx_available(struct mxc_spi_data *mxc_spi)
-{
- return readl(mxc_spi->base + MXC_CSPIINT) & MX27_INTREG_RR;
-}
-
-#define MX1_INTREG_RR (1 << 3)
-#define MX1_INTREG_TEEN (1 << 8)
-#define MX1_INTREG_RREN (1 << 11)
-
-#define MX1_CSPICTRL_POL (1 << 4)
-#define MX1_CSPICTRL_PHA (1 << 5)
-#define MX1_CSPICTRL_XCH (1 << 8)
-#define MX1_CSPICTRL_ENABLE (1 << 9)
-#define MX1_CSPICTRL_MASTER (1 << 10)
-#define MX1_CSPICTRL_DR_SHIFT 13
-
-static void mx1_intctrl(struct mxc_spi_data *mxc_spi, int enable)
-{
- unsigned int val = 0;
-
- if (enable & MXC_INT_TE)
- val |= MX1_INTREG_TEEN;
- if (enable & MXC_INT_RR)
- val |= MX1_INTREG_RREN;
-
- writel(val, mxc_spi->base + MXC_CSPIINT);
-}
-
-static void mx1_trigger(struct mxc_spi_data *mxc_spi)
-{
- unsigned int reg;
-
- reg = readl(mxc_spi->base + MXC_CSPICTRL);
- reg |= MX1_CSPICTRL_XCH;
- writel(reg, mxc_spi->base + MXC_CSPICTRL);
-}
-
-static int mx1_config(struct mxc_spi_data *mxc_spi,
- struct mxc_spi_config *config)
-{
- unsigned int reg = MX1_CSPICTRL_ENABLE | MX1_CSPICTRL_MASTER;
-
- reg |= mxc_spi_clkdiv_2(mxc_spi->spi_clk, config->speed_hz) <<
- MX1_CSPICTRL_DR_SHIFT;
- reg |= config->bpw - 1;
-
- if (config->mode & SPI_CPHA)
- reg |= MX1_CSPICTRL_PHA;
- if (config->mode & SPI_CPOL)
- reg |= MX1_CSPICTRL_POL;
-
- writel(reg, mxc_spi->base + MXC_CSPICTRL);
-
- return 0;
-}
-
-static int mx1_rx_available(struct mxc_spi_data *mxc_spi)
-{
- return readl(mxc_spi->base + MXC_CSPIINT) & MX1_INTREG_RR;
-}
-
-static void mxc_spi_chipselect(struct spi_device *spi, int is_active)
-{
- struct mxc_spi_data *mxc_spi = spi_master_get_devdata(spi->master);
- unsigned int cs = 0;
- int gpio = mxc_spi->chipselect[spi->chip_select];
- struct mxc_spi_config config;
-
- if (spi->mode & SPI_CS_HIGH)
- cs = 1;
-
- if (is_active == BITBANG_CS_INACTIVE) {
- if (gpio >= 0)
- gpio_set_value(gpio, !cs);
- return;
- }
-
- config.bpw = spi->bits_per_word;
- config.speed_hz = spi->max_speed_hz;
- config.mode = spi->mode;
- config.cs = mxc_spi->chipselect[spi->chip_select];
-
- mxc_spi->config(mxc_spi, &config);
-
- /* Initialize the functions for transfer */
- if (config.bpw <= 8) {
- mxc_spi->rx = mxc_spi_buf_rx_u8;
- mxc_spi->tx = mxc_spi_buf_tx_u8;
- } else if (config.bpw <= 16) {
- mxc_spi->rx = mxc_spi_buf_rx_u16;
- mxc_spi->tx = mxc_spi_buf_tx_u16;
- } else if (config.bpw <= 32) {
- mxc_spi->rx = mxc_spi_buf_rx_u32;
- mxc_spi->tx = mxc_spi_buf_tx_u32;
- } else
- BUG();
-
- if (gpio >= 0)
- gpio_set_value(gpio, cs);
-
- return;
-}
-
-static void mxc_spi_push(struct mxc_spi_data *mxc_spi)
-{
- while (mxc_spi->txfifo < 8) {
- if (!mxc_spi->count)
- break;
- mxc_spi->tx(mxc_spi);
- mxc_spi->txfifo++;
- }
-
- mxc_spi->trigger(mxc_spi);
-}
-
-static irqreturn_t mxc_spi_isr(int irq, void *dev_id)
-{
- struct mxc_spi_data *mxc_spi = dev_id;
-
- while (mxc_spi->rx_available(mxc_spi)) {
- mxc_spi->rx(mxc_spi);
- mxc_spi->txfifo--;
- }
-
- if (mxc_spi->count) {
- mxc_spi_push(mxc_spi);
- return IRQ_HANDLED;
- }
-
- if (mxc_spi->txfifo) {
- /* No data left to push, but still waiting for rx data,
- * enable receive data available interrupt.
- */
- mxc_spi->intctrl(mxc_spi, MXC_INT_RR);
- return IRQ_HANDLED;
- }
-
- mxc_spi->intctrl(mxc_spi, 0);
- complete(&mxc_spi->xfer_done);
-
- return IRQ_HANDLED;
-}
-
-static int mxc_spi_setupxfer(struct spi_device *spi,
- struct spi_transfer *t)
-{
- struct mxc_spi_data *mxc_spi = spi_master_get_devdata(spi->master);
- struct mxc_spi_config config;
-
- config.bpw = t ? t->bits_per_word : spi->bits_per_word;
- config.speed_hz = t ? t->speed_hz : spi->max_speed_hz;
- config.mode = spi->mode;
-
- mxc_spi->config(mxc_spi, &config);
-
- return 0;
-}
-
-static int mxc_spi_transfer(struct spi_device *spi,
- struct spi_transfer *transfer)
-{
- struct mxc_spi_data *mxc_spi = spi_master_get_devdata(spi->master);
-
- mxc_spi->tx_buf = transfer->tx_buf;
- mxc_spi->rx_buf = transfer->rx_buf;
- mxc_spi->count = transfer->len;
- mxc_spi->txfifo = 0;
-
- init_completion(&mxc_spi->xfer_done);
-
- mxc_spi_push(mxc_spi);
-
- mxc_spi->intctrl(mxc_spi, MXC_INT_TE);
-
- wait_for_completion(&mxc_spi->xfer_done);
-
- return transfer->len;
-}
-
-static int mxc_spi_setup(struct spi_device *spi)
-{
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
- pr_debug("%s: mode %d, %u bpw, %d hz\n", __func__,
- spi->mode, spi->bits_per_word, spi->max_speed_hz);
-
- mxc_spi_chipselect(spi, BITBANG_CS_INACTIVE);
-
- return 0;
-}
-
-static void mxc_spi_cleanup(struct spi_device *spi)
-{
-}
-
-static int __init mxc_spi_probe(struct platform_device *pdev)
-{
- struct spi_imx_master *mxc_platform_info;
- struct spi_master *master;
- struct mxc_spi_data *mxc_spi;
- struct resource *res;
- int i, ret;
-
- mxc_platform_info = (struct spi_imx_master *)pdev->dev.platform_data;
- if (!mxc_platform_info) {
- dev_err(&pdev->dev, "can't get the platform data\n");
- return -EINVAL;
- }
-
- master = spi_alloc_master(&pdev->dev, sizeof(struct mxc_spi_data));
- if (!master)
- return -ENOMEM;
-
- platform_set_drvdata(pdev, master);
-
- master->bus_num = pdev->id;
- master->num_chipselect = mxc_platform_info->num_chipselect;
-
- mxc_spi = spi_master_get_devdata(master);
- mxc_spi->bitbang.master = spi_master_get(master);
- mxc_spi->chipselect = mxc_platform_info->chipselect;
-
- for (i = 0; i < master->num_chipselect; i++) {
- if (mxc_spi->chipselect[i] < 0)
- continue;
- ret = gpio_request(mxc_spi->chipselect[i], DRIVER_NAME);
- if (ret) {
- i--;
- while (i > 0)
- if (mxc_spi->chipselect[i] >= 0)
- gpio_free(mxc_spi->chipselect[i--]);
- dev_err(&pdev->dev, "can't get cs gpios");
- goto out_master_put;
- }
- gpio_direction_output(mxc_spi->chipselect[i], 1);
- }
-
- mxc_spi->bitbang.chipselect = mxc_spi_chipselect;
- mxc_spi->bitbang.setup_transfer = mxc_spi_setupxfer;
- mxc_spi->bitbang.txrx_bufs = mxc_spi_transfer;
- mxc_spi->bitbang.master->setup = mxc_spi_setup;
- mxc_spi->bitbang.master->cleanup = mxc_spi_cleanup;
-
- init_completion(&mxc_spi->xfer_done);
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "can't get platform resource\n");
- ret = -ENOMEM;
- goto out_gpio_free;
- }
-
- if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
- dev_err(&pdev->dev, "request_mem_region failed\n");
- ret = -EBUSY;
- goto out_gpio_free;
- }
-
- mxc_spi->base = ioremap(res->start, resource_size(res));
- if (!mxc_spi->base) {
- ret = -EINVAL;
- goto out_release_mem;
- }
-
- mxc_spi->irq = platform_get_irq(pdev, 0);
- if (!mxc_spi->irq) {
- ret = -EINVAL;
- goto out_iounmap;
- }
-
- ret = request_irq(mxc_spi->irq, mxc_spi_isr, 0, DRIVER_NAME, mxc_spi);
- if (ret) {
- dev_err(&pdev->dev, "can't get irq%d: %d\n", mxc_spi->irq, ret);
- goto out_iounmap;
- }
-
- if (cpu_is_mx31() || cpu_is_mx35()) {
- mxc_spi->intctrl = mx31_intctrl;
- mxc_spi->config = mx31_config;
- mxc_spi->trigger = mx31_trigger;
- mxc_spi->rx_available = mx31_rx_available;
- } else if (cpu_is_mx27() || cpu_is_mx21()) {
- mxc_spi->intctrl = mx27_intctrl;
- mxc_spi->config = mx27_config;
- mxc_spi->trigger = mx27_trigger;
- mxc_spi->rx_available = mx27_rx_available;
- } else if (cpu_is_mx1()) {
- mxc_spi->intctrl = mx1_intctrl;
- mxc_spi->config = mx1_config;
- mxc_spi->trigger = mx1_trigger;
- mxc_spi->rx_available = mx1_rx_available;
- } else
- BUG();
-
- mxc_spi->clk = clk_get(&pdev->dev, NULL);
- if (IS_ERR(mxc_spi->clk)) {
- dev_err(&pdev->dev, "unable to get clock\n");
- ret = PTR_ERR(mxc_spi->clk);
- goto out_free_irq;
- }
-
- clk_enable(mxc_spi->clk);
- mxc_spi->spi_clk = clk_get_rate(mxc_spi->clk);
-
- if (!cpu_is_mx31() || !cpu_is_mx35())
- writel(1, mxc_spi->base + MXC_RESET);
-
- mxc_spi->intctrl(mxc_spi, 0);
-
- ret = spi_bitbang_start(&mxc_spi->bitbang);
- if (ret) {
- dev_err(&pdev->dev, "bitbang start failed with %d\n", ret);
- goto out_clk_put;
- }
-
- dev_info(&pdev->dev, "probed\n");
-
- return ret;
-
-out_clk_put:
- clk_disable(mxc_spi->clk);
- clk_put(mxc_spi->clk);
-out_free_irq:
- free_irq(mxc_spi->irq, mxc_spi);
-out_iounmap:
- iounmap(mxc_spi->base);
-out_release_mem:
- release_mem_region(res->start, resource_size(res));
-out_gpio_free:
- for (i = 0; i < master->num_chipselect; i++)
- if (mxc_spi->chipselect[i] >= 0)
- gpio_free(mxc_spi->chipselect[i]);
-out_master_put:
- spi_master_put(master);
- kfree(master);
- platform_set_drvdata(pdev, NULL);
- return ret;
-}
-
-static int __exit mxc_spi_remove(struct platform_device *pdev)
-{
- struct spi_master *master = platform_get_drvdata(pdev);
- struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- struct mxc_spi_data *mxc_spi = spi_master_get_devdata(master);
- int i;
-
- spi_bitbang_stop(&mxc_spi->bitbang);
-
- writel(0, mxc_spi->base + MXC_CSPICTRL);
- clk_disable(mxc_spi->clk);
- clk_put(mxc_spi->clk);
- free_irq(mxc_spi->irq, mxc_spi);
- iounmap(mxc_spi->base);
-
- for (i = 0; i < master->num_chipselect; i++)
- if (mxc_spi->chipselect[i] >= 0)
- gpio_free(mxc_spi->chipselect[i]);
-
- spi_master_put(master);
-
- release_mem_region(res->start, resource_size(res));
-
- platform_set_drvdata(pdev, NULL);
-
- return 0;
-}
-
-static struct platform_driver mxc_spi_driver = {
- .driver = {
- .name = DRIVER_NAME,
- .owner = THIS_MODULE,
- },
- .probe = mxc_spi_probe,
- .remove = __exit_p(mxc_spi_remove),
-};
-
-static int __init mxc_spi_init(void)
-{
- return platform_driver_register(&mxc_spi_driver);
-}
-
-static void __exit mxc_spi_exit(void)
-{
- platform_driver_unregister(&mxc_spi_driver);
-}
-
-module_init(mxc_spi_init);
-module_exit(mxc_spi_exit);
-
-MODULE_DESCRIPTION("SPI Master Controller driver");
-MODULE_AUTHOR("Sascha Hauer, Pengutronix");
-MODULE_LICENSE("GPL");
}
#ifdef CONFIG_PM
-
-static int pxa2xx_spi_suspend(struct platform_device *pdev, pm_message_t state)
+static int pxa2xx_spi_suspend(struct device *dev)
{
- struct driver_data *drv_data = platform_get_drvdata(pdev);
+ struct driver_data *drv_data = dev_get_drvdata(dev);
struct ssp_device *ssp = drv_data->ssp;
int status = 0;
return 0;
}
-static int pxa2xx_spi_resume(struct platform_device *pdev)
+static int pxa2xx_spi_resume(struct device *dev)
{
- struct driver_data *drv_data = platform_get_drvdata(pdev);
+ struct driver_data *drv_data = dev_get_drvdata(dev);
struct ssp_device *ssp = drv_data->ssp;
int status = 0;
/* Start the queue running */
status = start_queue(drv_data);
if (status != 0) {
- dev_err(&pdev->dev, "problem starting queue (%d)\n", status);
+ dev_err(dev, "problem starting queue (%d)\n", status);
return status;
}
return 0;
}
-#else
-#define pxa2xx_spi_suspend NULL
-#define pxa2xx_spi_resume NULL
-#endif /* CONFIG_PM */
+
+static struct dev_pm_ops pxa2xx_spi_pm_ops = {
+ .suspend = pxa2xx_spi_suspend,
+ .resume = pxa2xx_spi_resume,
+};
+#endif
static struct platform_driver driver = {
.driver = {
- .name = "pxa2xx-spi",
- .owner = THIS_MODULE,
+ .name = "pxa2xx-spi",
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxa2xx_spi_pm_ops,
+#endif
},
.remove = pxa2xx_spi_remove,
.shutdown = pxa2xx_spi_shutdown,
- .suspend = pxa2xx_spi_suspend,
- .resume = pxa2xx_spi_resume,
};
static int __init pxa2xx_spi_init(void)
--- /dev/null
+/*
+ * Copyright 2004-2007 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2008 Juergen Beisert
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the
+ * Free Software Foundation
+ * 51 Franklin Street, Fifth Floor
+ * Boston, MA 02110-1301, USA.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+#include <linux/types.h>
+
+#include <mach/spi.h>
+
+#define DRIVER_NAME "spi_imx"
+
+#define MXC_CSPIRXDATA 0x00
+#define MXC_CSPITXDATA 0x04
+#define MXC_CSPICTRL 0x08
+#define MXC_CSPIINT 0x0c
+#define MXC_RESET 0x1c
+
+/* generic defines to abstract from the different register layouts */
+#define MXC_INT_RR (1 << 0) /* Receive data ready interrupt */
+#define MXC_INT_TE (1 << 1) /* Transmit FIFO empty interrupt */
+
+struct spi_imx_config {
+ unsigned int speed_hz;
+ unsigned int bpw;
+ unsigned int mode;
+ int cs;
+};
+
+struct spi_imx_data {
+ struct spi_bitbang bitbang;
+
+ struct completion xfer_done;
+ void *base;
+ int irq;
+ struct clk *clk;
+ unsigned long spi_clk;
+ int *chipselect;
+
+ unsigned int count;
+ void (*tx)(struct spi_imx_data *);
+ void (*rx)(struct spi_imx_data *);
+ void *rx_buf;
+ const void *tx_buf;
+ unsigned int txfifo; /* number of words pushed in tx FIFO */
+
+ /* SoC specific functions */
+ void (*intctrl)(struct spi_imx_data *, int);
+ int (*config)(struct spi_imx_data *, struct spi_imx_config *);
+ void (*trigger)(struct spi_imx_data *);
+ int (*rx_available)(struct spi_imx_data *);
+};
+
+#define MXC_SPI_BUF_RX(type) \
+static void spi_imx_buf_rx_##type(struct spi_imx_data *spi_imx) \
+{ \
+ unsigned int val = readl(spi_imx->base + MXC_CSPIRXDATA); \
+ \
+ if (spi_imx->rx_buf) { \
+ *(type *)spi_imx->rx_buf = val; \
+ spi_imx->rx_buf += sizeof(type); \
+ } \
+}
+
+#define MXC_SPI_BUF_TX(type) \
+static void spi_imx_buf_tx_##type(struct spi_imx_data *spi_imx) \
+{ \
+ type val = 0; \
+ \
+ if (spi_imx->tx_buf) { \
+ val = *(type *)spi_imx->tx_buf; \
+ spi_imx->tx_buf += sizeof(type); \
+ } \
+ \
+ spi_imx->count -= sizeof(type); \
+ \
+ writel(val, spi_imx->base + MXC_CSPITXDATA); \
+}
+
+MXC_SPI_BUF_RX(u8)
+MXC_SPI_BUF_TX(u8)
+MXC_SPI_BUF_RX(u16)
+MXC_SPI_BUF_TX(u16)
+MXC_SPI_BUF_RX(u32)
+MXC_SPI_BUF_TX(u32)
+
+/* First entry is reserved, second entry is valid only if SDHC_SPIEN is set
+ * (which is currently not the case in this driver)
+ */
+static int mxc_clkdivs[] = {0, 3, 4, 6, 8, 12, 16, 24, 32, 48, 64, 96, 128, 192,
+ 256, 384, 512, 768, 1024};
+
+/* MX21, MX27 */
+static unsigned int spi_imx_clkdiv_1(unsigned int fin,
+ unsigned int fspi)
+{
+ int i, max;
+
+ if (cpu_is_mx21())
+ max = 18;
+ else
+ max = 16;
+
+ for (i = 2; i < max; i++)
+ if (fspi * mxc_clkdivs[i] >= fin)
+ return i;
+
+ return max;
+}
+
+/* MX1, MX31, MX35 */
+static unsigned int spi_imx_clkdiv_2(unsigned int fin,
+ unsigned int fspi)
+{
+ int i, div = 4;
+
+ for (i = 0; i < 7; i++) {
+ if (fspi * div >= fin)
+ return i;
+ div <<= 1;
+ }
+
+ return 7;
+}
+
+#define MX31_INTREG_TEEN (1 << 0)
+#define MX31_INTREG_RREN (1 << 3)
+
+#define MX31_CSPICTRL_ENABLE (1 << 0)
+#define MX31_CSPICTRL_MASTER (1 << 1)
+#define MX31_CSPICTRL_XCH (1 << 2)
+#define MX31_CSPICTRL_POL (1 << 4)
+#define MX31_CSPICTRL_PHA (1 << 5)
+#define MX31_CSPICTRL_SSCTL (1 << 6)
+#define MX31_CSPICTRL_SSPOL (1 << 7)
+#define MX31_CSPICTRL_BC_SHIFT 8
+#define MX35_CSPICTRL_BL_SHIFT 20
+#define MX31_CSPICTRL_CS_SHIFT 24
+#define MX35_CSPICTRL_CS_SHIFT 12
+#define MX31_CSPICTRL_DR_SHIFT 16
+
+#define MX31_CSPISTATUS 0x14
+#define MX31_STATUS_RR (1 << 3)
+
+/* These functions also work for the i.MX35, but be aware that
+ * the i.MX35 has a slightly different register layout for bits
+ * we do not use here.
+ */
+static void mx31_intctrl(struct spi_imx_data *spi_imx, int enable)
+{
+ unsigned int val = 0;
+
+ if (enable & MXC_INT_TE)
+ val |= MX31_INTREG_TEEN;
+ if (enable & MXC_INT_RR)
+ val |= MX31_INTREG_RREN;
+
+ writel(val, spi_imx->base + MXC_CSPIINT);
+}
+
+static void mx31_trigger(struct spi_imx_data *spi_imx)
+{
+ unsigned int reg;
+
+ reg = readl(spi_imx->base + MXC_CSPICTRL);
+ reg |= MX31_CSPICTRL_XCH;
+ writel(reg, spi_imx->base + MXC_CSPICTRL);
+}
+
+static int mx31_config(struct spi_imx_data *spi_imx,
+ struct spi_imx_config *config)
+{
+ unsigned int reg = MX31_CSPICTRL_ENABLE | MX31_CSPICTRL_MASTER;
+
+ reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, config->speed_hz) <<
+ MX31_CSPICTRL_DR_SHIFT;
+
+ if (cpu_is_mx31())
+ reg |= (config->bpw - 1) << MX31_CSPICTRL_BC_SHIFT;
+ else if (cpu_is_mx35()) {
+ reg |= (config->bpw - 1) << MX35_CSPICTRL_BL_SHIFT;
+ reg |= MX31_CSPICTRL_SSCTL;
+ }
+
+ if (config->mode & SPI_CPHA)
+ reg |= MX31_CSPICTRL_PHA;
+ if (config->mode & SPI_CPOL)
+ reg |= MX31_CSPICTRL_POL;
+ if (config->mode & SPI_CS_HIGH)
+ reg |= MX31_CSPICTRL_SSPOL;
+ if (config->cs < 0) {
+ if (cpu_is_mx31())
+ reg |= (config->cs + 32) << MX31_CSPICTRL_CS_SHIFT;
+ else if (cpu_is_mx35())
+ reg |= (config->cs + 32) << MX35_CSPICTRL_CS_SHIFT;
+ }
+
+ writel(reg, spi_imx->base + MXC_CSPICTRL);
+
+ return 0;
+}
+
+static int mx31_rx_available(struct spi_imx_data *spi_imx)
+{
+ return readl(spi_imx->base + MX31_CSPISTATUS) & MX31_STATUS_RR;
+}
+
+#define MX27_INTREG_RR (1 << 4)
+#define MX27_INTREG_TEEN (1 << 9)
+#define MX27_INTREG_RREN (1 << 13)
+
+#define MX27_CSPICTRL_POL (1 << 5)
+#define MX27_CSPICTRL_PHA (1 << 6)
+#define MX27_CSPICTRL_SSPOL (1 << 8)
+#define MX27_CSPICTRL_XCH (1 << 9)
+#define MX27_CSPICTRL_ENABLE (1 << 10)
+#define MX27_CSPICTRL_MASTER (1 << 11)
+#define MX27_CSPICTRL_DR_SHIFT 14
+#define MX27_CSPICTRL_CS_SHIFT 19
+
+static void mx27_intctrl(struct spi_imx_data *spi_imx, int enable)
+{
+ unsigned int val = 0;
+
+ if (enable & MXC_INT_TE)
+ val |= MX27_INTREG_TEEN;
+ if (enable & MXC_INT_RR)
+ val |= MX27_INTREG_RREN;
+
+ writel(val, spi_imx->base + MXC_CSPIINT);
+}
+
+static void mx27_trigger(struct spi_imx_data *spi_imx)
+{
+ unsigned int reg;
+
+ reg = readl(spi_imx->base + MXC_CSPICTRL);
+ reg |= MX27_CSPICTRL_XCH;
+ writel(reg, spi_imx->base + MXC_CSPICTRL);
+}
+
+static int mx27_config(struct spi_imx_data *spi_imx,
+ struct spi_imx_config *config)
+{
+ unsigned int reg = MX27_CSPICTRL_ENABLE | MX27_CSPICTRL_MASTER;
+
+ reg |= spi_imx_clkdiv_1(spi_imx->spi_clk, config->speed_hz) <<
+ MX27_CSPICTRL_DR_SHIFT;
+ reg |= config->bpw - 1;
+
+ if (config->mode & SPI_CPHA)
+ reg |= MX27_CSPICTRL_PHA;
+ if (config->mode & SPI_CPOL)
+ reg |= MX27_CSPICTRL_POL;
+ if (config->mode & SPI_CS_HIGH)
+ reg |= MX27_CSPICTRL_SSPOL;
+ if (config->cs < 0)
+ reg |= (config->cs + 32) << MX27_CSPICTRL_CS_SHIFT;
+
+ writel(reg, spi_imx->base + MXC_CSPICTRL);
+
+ return 0;
+}
+
+static int mx27_rx_available(struct spi_imx_data *spi_imx)
+{
+ return readl(spi_imx->base + MXC_CSPIINT) & MX27_INTREG_RR;
+}
+
+#define MX1_INTREG_RR (1 << 3)
+#define MX1_INTREG_TEEN (1 << 8)
+#define MX1_INTREG_RREN (1 << 11)
+
+#define MX1_CSPICTRL_POL (1 << 4)
+#define MX1_CSPICTRL_PHA (1 << 5)
+#define MX1_CSPICTRL_XCH (1 << 8)
+#define MX1_CSPICTRL_ENABLE (1 << 9)
+#define MX1_CSPICTRL_MASTER (1 << 10)
+#define MX1_CSPICTRL_DR_SHIFT 13
+
+static void mx1_intctrl(struct spi_imx_data *spi_imx, int enable)
+{
+ unsigned int val = 0;
+
+ if (enable & MXC_INT_TE)
+ val |= MX1_INTREG_TEEN;
+ if (enable & MXC_INT_RR)
+ val |= MX1_INTREG_RREN;
+
+ writel(val, spi_imx->base + MXC_CSPIINT);
+}
+
+static void mx1_trigger(struct spi_imx_data *spi_imx)
+{
+ unsigned int reg;
+
+ reg = readl(spi_imx->base + MXC_CSPICTRL);
+ reg |= MX1_CSPICTRL_XCH;
+ writel(reg, spi_imx->base + MXC_CSPICTRL);
+}
+
+static int mx1_config(struct spi_imx_data *spi_imx,
+ struct spi_imx_config *config)
+{
+ unsigned int reg = MX1_CSPICTRL_ENABLE | MX1_CSPICTRL_MASTER;
+
+ reg |= spi_imx_clkdiv_2(spi_imx->spi_clk, config->speed_hz) <<
+ MX1_CSPICTRL_DR_SHIFT;
+ reg |= config->bpw - 1;
+
+ if (config->mode & SPI_CPHA)
+ reg |= MX1_CSPICTRL_PHA;
+ if (config->mode & SPI_CPOL)
+ reg |= MX1_CSPICTRL_POL;
+
+ writel(reg, spi_imx->base + MXC_CSPICTRL);
+
+ return 0;
+}
+
+static int mx1_rx_available(struct spi_imx_data *spi_imx)
+{
+ return readl(spi_imx->base + MXC_CSPIINT) & MX1_INTREG_RR;
+}
+
+static void spi_imx_chipselect(struct spi_device *spi, int is_active)
+{
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+ int gpio = spi_imx->chipselect[spi->chip_select];
+ int active = is_active != BITBANG_CS_INACTIVE;
+ int dev_is_lowactive = !(spi->mode & SPI_CS_HIGH);
+
+ if (gpio < 0)
+ return;
+
+ gpio_set_value(gpio, dev_is_lowactive ^ active);
+}
+
+static void spi_imx_push(struct spi_imx_data *spi_imx)
+{
+ while (spi_imx->txfifo < 8) {
+ if (!spi_imx->count)
+ break;
+ spi_imx->tx(spi_imx);
+ spi_imx->txfifo++;
+ }
+
+ spi_imx->trigger(spi_imx);
+}
+
+static irqreturn_t spi_imx_isr(int irq, void *dev_id)
+{
+ struct spi_imx_data *spi_imx = dev_id;
+
+ while (spi_imx->rx_available(spi_imx)) {
+ spi_imx->rx(spi_imx);
+ spi_imx->txfifo--;
+ }
+
+ if (spi_imx->count) {
+ spi_imx_push(spi_imx);
+ return IRQ_HANDLED;
+ }
+
+ if (spi_imx->txfifo) {
+ /* No data left to push, but still waiting for rx data,
+ * enable receive data available interrupt.
+ */
+ spi_imx->intctrl(spi_imx, MXC_INT_RR);
+ return IRQ_HANDLED;
+ }
+
+ spi_imx->intctrl(spi_imx, 0);
+ complete(&spi_imx->xfer_done);
+
+ return IRQ_HANDLED;
+}
+
+static int spi_imx_setupxfer(struct spi_device *spi,
+ struct spi_transfer *t)
+{
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+ struct spi_imx_config config;
+
+ config.bpw = t ? t->bits_per_word : spi->bits_per_word;
+ config.speed_hz = t ? t->speed_hz : spi->max_speed_hz;
+ config.mode = spi->mode;
+ config.cs = spi_imx->chipselect[spi->chip_select];
+
+ if (!config.speed_hz)
+ config.speed_hz = spi->max_speed_hz;
+ if (!config.bpw)
+ config.bpw = spi->bits_per_word;
+ if (!config.speed_hz)
+ config.speed_hz = spi->max_speed_hz;
+
+ /* Initialize the functions for transfer */
+ if (config.bpw <= 8) {
+ spi_imx->rx = spi_imx_buf_rx_u8;
+ spi_imx->tx = spi_imx_buf_tx_u8;
+ } else if (config.bpw <= 16) {
+ spi_imx->rx = spi_imx_buf_rx_u16;
+ spi_imx->tx = spi_imx_buf_tx_u16;
+ } else if (config.bpw <= 32) {
+ spi_imx->rx = spi_imx_buf_rx_u32;
+ spi_imx->tx = spi_imx_buf_tx_u32;
+ } else
+ BUG();
+
+ spi_imx->config(spi_imx, &config);
+
+ return 0;
+}
+
+static int spi_imx_transfer(struct spi_device *spi,
+ struct spi_transfer *transfer)
+{
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+
+ spi_imx->tx_buf = transfer->tx_buf;
+ spi_imx->rx_buf = transfer->rx_buf;
+ spi_imx->count = transfer->len;
+ spi_imx->txfifo = 0;
+
+ init_completion(&spi_imx->xfer_done);
+
+ spi_imx_push(spi_imx);
+
+ spi_imx->intctrl(spi_imx, MXC_INT_TE);
+
+ wait_for_completion(&spi_imx->xfer_done);
+
+ return transfer->len;
+}
+
+static int spi_imx_setup(struct spi_device *spi)
+{
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(spi->master);
+ int gpio = spi_imx->chipselect[spi->chip_select];
+
+ pr_debug("%s: mode %d, %u bpw, %d hz\n", __func__,
+ spi->mode, spi->bits_per_word, spi->max_speed_hz);
+
+ if (gpio >= 0)
+ gpio_direction_output(gpio, spi->mode & SPI_CS_HIGH ? 0 : 1);
+
+ spi_imx_chipselect(spi, BITBANG_CS_INACTIVE);
+
+ return 0;
+}
+
+static void spi_imx_cleanup(struct spi_device *spi)
+{
+}
+
+static int __init spi_imx_probe(struct platform_device *pdev)
+{
+ struct spi_imx_master *mxc_platform_info;
+ struct spi_master *master;
+ struct spi_imx_data *spi_imx;
+ struct resource *res;
+ int i, ret;
+
+ mxc_platform_info = (struct spi_imx_master *)pdev->dev.platform_data;
+ if (!mxc_platform_info) {
+ dev_err(&pdev->dev, "can't get the platform data\n");
+ return -EINVAL;
+ }
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct spi_imx_data));
+ if (!master)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, master);
+
+ master->bus_num = pdev->id;
+ master->num_chipselect = mxc_platform_info->num_chipselect;
+
+ spi_imx = spi_master_get_devdata(master);
+ spi_imx->bitbang.master = spi_master_get(master);
+ spi_imx->chipselect = mxc_platform_info->chipselect;
+
+ for (i = 0; i < master->num_chipselect; i++) {
+ if (spi_imx->chipselect[i] < 0)
+ continue;
+ ret = gpio_request(spi_imx->chipselect[i], DRIVER_NAME);
+ if (ret) {
+ i--;
+ while (i > 0)
+ if (spi_imx->chipselect[i] >= 0)
+ gpio_free(spi_imx->chipselect[i--]);
+ dev_err(&pdev->dev, "can't get cs gpios");
+ goto out_master_put;
+ }
+ }
+
+ spi_imx->bitbang.chipselect = spi_imx_chipselect;
+ spi_imx->bitbang.setup_transfer = spi_imx_setupxfer;
+ spi_imx->bitbang.txrx_bufs = spi_imx_transfer;
+ spi_imx->bitbang.master->setup = spi_imx_setup;
+ spi_imx->bitbang.master->cleanup = spi_imx_cleanup;
+ spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+
+ init_completion(&spi_imx->xfer_done);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "can't get platform resource\n");
+ ret = -ENOMEM;
+ goto out_gpio_free;
+ }
+
+ if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
+ dev_err(&pdev->dev, "request_mem_region failed\n");
+ ret = -EBUSY;
+ goto out_gpio_free;
+ }
+
+ spi_imx->base = ioremap(res->start, resource_size(res));
+ if (!spi_imx->base) {
+ ret = -EINVAL;
+ goto out_release_mem;
+ }
+
+ spi_imx->irq = platform_get_irq(pdev, 0);
+ if (!spi_imx->irq) {
+ ret = -EINVAL;
+ goto out_iounmap;
+ }
+
+ ret = request_irq(spi_imx->irq, spi_imx_isr, 0, DRIVER_NAME, spi_imx);
+ if (ret) {
+ dev_err(&pdev->dev, "can't get irq%d: %d\n", spi_imx->irq, ret);
+ goto out_iounmap;
+ }
+
+ if (cpu_is_mx31() || cpu_is_mx35()) {
+ spi_imx->intctrl = mx31_intctrl;
+ spi_imx->config = mx31_config;
+ spi_imx->trigger = mx31_trigger;
+ spi_imx->rx_available = mx31_rx_available;
+ } else if (cpu_is_mx27() || cpu_is_mx21()) {
+ spi_imx->intctrl = mx27_intctrl;
+ spi_imx->config = mx27_config;
+ spi_imx->trigger = mx27_trigger;
+ spi_imx->rx_available = mx27_rx_available;
+ } else if (cpu_is_mx1()) {
+ spi_imx->intctrl = mx1_intctrl;
+ spi_imx->config = mx1_config;
+ spi_imx->trigger = mx1_trigger;
+ spi_imx->rx_available = mx1_rx_available;
+ } else
+ BUG();
+
+ spi_imx->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(spi_imx->clk)) {
+ dev_err(&pdev->dev, "unable to get clock\n");
+ ret = PTR_ERR(spi_imx->clk);
+ goto out_free_irq;
+ }
+
+ clk_enable(spi_imx->clk);
+ spi_imx->spi_clk = clk_get_rate(spi_imx->clk);
+
+ if (!cpu_is_mx31() || !cpu_is_mx35())
+ writel(1, spi_imx->base + MXC_RESET);
+
+ spi_imx->intctrl(spi_imx, 0);
+
+ ret = spi_bitbang_start(&spi_imx->bitbang);
+ if (ret) {
+ dev_err(&pdev->dev, "bitbang start failed with %d\n", ret);
+ goto out_clk_put;
+ }
+
+ dev_info(&pdev->dev, "probed\n");
+
+ return ret;
+
+out_clk_put:
+ clk_disable(spi_imx->clk);
+ clk_put(spi_imx->clk);
+out_free_irq:
+ free_irq(spi_imx->irq, spi_imx);
+out_iounmap:
+ iounmap(spi_imx->base);
+out_release_mem:
+ release_mem_region(res->start, resource_size(res));
+out_gpio_free:
+ for (i = 0; i < master->num_chipselect; i++)
+ if (spi_imx->chipselect[i] >= 0)
+ gpio_free(spi_imx->chipselect[i]);
+out_master_put:
+ spi_master_put(master);
+ kfree(master);
+ platform_set_drvdata(pdev, NULL);
+ return ret;
+}
+
+static int __exit spi_imx_remove(struct platform_device *pdev)
+{
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
+ int i;
+
+ spi_bitbang_stop(&spi_imx->bitbang);
+
+ writel(0, spi_imx->base + MXC_CSPICTRL);
+ clk_disable(spi_imx->clk);
+ clk_put(spi_imx->clk);
+ free_irq(spi_imx->irq, spi_imx);
+ iounmap(spi_imx->base);
+
+ for (i = 0; i < master->num_chipselect; i++)
+ if (spi_imx->chipselect[i] >= 0)
+ gpio_free(spi_imx->chipselect[i]);
+
+ spi_master_put(master);
+
+ release_mem_region(res->start, resource_size(res));
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver spi_imx_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = spi_imx_probe,
+ .remove = __exit_p(spi_imx_remove),
+};
+
+static int __init spi_imx_init(void)
+{
+ return platform_driver_register(&spi_imx_driver);
+}
+
+static void __exit spi_imx_exit(void)
+{
+ platform_driver_unregister(&spi_imx_driver);
+}
+
+module_init(spi_imx_init);
+module_exit(spi_imx_exit);
+
+MODULE_DESCRIPTION("SPI Master Controller driver");
+MODULE_AUTHOR("Sascha Hauer, Pengutronix");
+MODULE_LICENSE("GPL");
return status;
}
-static struct file_operations spidev_fops = {
+static const struct file_operations spidev_fops = {
.owner = THIS_MODULE,
/* REVISIT switch to aio primitives, so that userspace
* gets more complete API coverage. It'll simplify things
source "drivers/staging/vt6656/Kconfig"
-source "drivers/staging/cpc-usb/Kconfig"
-
source "drivers/staging/udlfb/Kconfig"
source "drivers/staging/hv/Kconfig"
obj-$(CONFIG_OCTEON_ETHERNET) += octeon/
obj-$(CONFIG_VT6655) += vt6655/
obj-$(CONFIG_VT6656) += vt6656/
-obj-$(CONFIG_USB_CPC) += cpc-usb/
obj-$(CONFIG_FB_UDL) += udlfb/
obj-$(CONFIG_HYPERV) += hv/
obj-$(CONFIG_VME_BUS) += vme/
+++ /dev/null
-config USB_CPC
- tristate "CPC CAN USB driver"
- depends on USB && PROC_FS
- default n
+++ /dev/null
-obj-$(CONFIG_USB_CPC) += cpc-usb.o
-
-cpc-usb-y := cpc-usb_drv.o sja2m16c_2.o
+++ /dev/null
-Things to do for this driver to get merged into the main portion of the
-kernel:
- - checkpatch cleanups
- - sparse clean
- - remove proc code
- - tie into CAN socket interfaces if possible
- - figure out sane userspace api
- - use linux's error codes
-
-Send patches to Greg Kroah-Hartman <greg@kroah.com>
+++ /dev/null
-/*
- * CPC-USB CAN Interface Kernel Driver
- *
- * Copyright (C) 2004-2009 EMS Dr. Thomas Wuensche
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published
- * by the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
- */
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/vmalloc.h>
-#include <linux/module.h>
-#include <linux/poll.h>
-#include <linux/smp_lock.h>
-#include <linux/completion.h>
-#include <asm/uaccess.h>
-#include <linux/usb.h>
-
-
-#include <linux/proc_fs.h>
-
-#include "cpc.h"
-
-#include "cpc_int.h"
-#include "cpcusb.h"
-
-#include "sja2m16c.h"
-
-/* Version Information */
-#define DRIVER_AUTHOR "Sebastian Haas <haas@ems-wuensche.com>"
-#define DRIVER_DESC "CPC-USB Driver for Linux Kernel 2.6"
-#define DRIVER_VERSION CPC_DRIVER_VERSION
-
-MODULE_AUTHOR(DRIVER_AUTHOR);
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_VERSION(DRIVER_VERSION);
-MODULE_LICENSE("GPL v2");
-
-/* Define these values to match your devices */
-#define USB_CPCUSB_VENDOR_ID 0x12D6
-
-#define USB_CPCUSB_M16C_PRODUCT_ID 0x0888
-#define USB_CPCUSB_LPC2119_PRODUCT_ID 0x0444
-
-#define CPC_USB_PROC_DIR CPC_PROC_DIR "cpc-usb"
-
-static struct proc_dir_entry *procDir;
-static struct proc_dir_entry *procEntry;
-
-/* Module parameters */
-static int debug;
-module_param(debug, int, S_IRUGO);
-
-/* table of devices that work with this driver */
-static struct usb_device_id cpcusb_table[] = {
- {USB_DEVICE(USB_CPCUSB_VENDOR_ID, USB_CPCUSB_M16C_PRODUCT_ID)},
- {USB_DEVICE(USB_CPCUSB_VENDOR_ID, USB_CPCUSB_LPC2119_PRODUCT_ID)},
- {} /* Terminating entry */
-};
-
-MODULE_DEVICE_TABLE(usb, cpcusb_table);
-
-/* use to prevent kernel panic if driver is unloaded
- * while a programm has still open the device
- */
-DECLARE_WAIT_QUEUE_HEAD(rmmodWq);
-atomic_t useCount;
-
-static CPC_USB_T *CPCUSB_Table[CPC_USB_CARD_CNT] = { 0 };
-static unsigned int CPCUsbCnt;
-
-/* prevent races between open() and disconnect() */
-static DECLARE_MUTEX(disconnect_sem);
-
-/* local function prototypes */
-static ssize_t cpcusb_read(struct file *file, char *buffer, size_t count,
- loff_t *ppos);
-static ssize_t cpcusb_write(struct file *file, const char *buffer,
- size_t count, loff_t *ppos);
-static unsigned int cpcusb_poll(struct file *file, poll_table * wait);
-static int cpcusb_open(struct inode *inode, struct file *file);
-static int cpcusb_release(struct inode *inode, struct file *file);
-
-static int cpcusb_probe(struct usb_interface *interface,
- const struct usb_device_id *id);
-static void cpcusb_disconnect(struct usb_interface *interface);
-
-static void cpcusb_read_bulk_callback(struct urb *urb);
-static void cpcusb_write_bulk_callback(struct urb *urb);
-static void cpcusb_read_interrupt_callback(struct urb *urb);
-
-static int cpcusb_setup_intrep(CPC_USB_T *card);
-
-static struct file_operations cpcusb_fops = {
- /*
- * The owner field is part of the module-locking
- * mechanism. The idea is that the kernel knows
- * which module to increment the use-counter of
- * BEFORE it calls the device's open() function.
- * This also means that the kernel can decrement
- * the use-counter again before calling release()
- * or should the open() function fail.
- */
- .owner = THIS_MODULE,
-
- .read = cpcusb_read,
- .write = cpcusb_write,
- .poll = cpcusb_poll,
- .open = cpcusb_open,
- .release = cpcusb_release,
-};
-
-/*
- * usb class driver info in order to get a minor number from the usb core,
- * and to have the device registered with devfs and the driver core
- */
-static struct usb_class_driver cpcusb_class = {
- .name = "usb/cpc_usb%d",
- .fops = &cpcusb_fops,
- .minor_base = CPC_USB_BASE_MNR,
-};
-
-/* usb specific object needed to register this driver with the usb subsystem */
-static struct usb_driver cpcusb_driver = {
- .name = "cpc-usb",
- .probe = cpcusb_probe,
- .disconnect = cpcusb_disconnect,
- .id_table = cpcusb_table,
-};
-
-static int cpcusb_create_info_output(char *buf)
-{
- int i = 0, j;
-
- for (j = 0; j < CPC_USB_CARD_CNT; j++) {
- if (CPCUSB_Table[j]) {
- CPC_USB_T *card = CPCUSB_Table[j];
- CPC_CHAN_T *chan = card->chan;
-
- /* MINOR CHANNELNO BUSNO SLOTNO */
- i += sprintf(&buf[i], "%d %s\n", chan->minor,
- card->serialNumber);
- }
- }
-
- return i;
-}
-
-static int cpcusb_proc_read_info(char *page, char **start, off_t off,
- int count, int *eof, void *data)
-{
- int len = cpcusb_create_info_output(page);
-
- if (len <= off + count)
- *eof = 1;
- *start = page + off;
- len -= off;
- if (len > count)
- len = count;
- if (len < 0)
- len = 0;
-
- return len;
-}
-
-/*
- * Remove CPC-USB and cleanup
- */
-static inline void cpcusb_delete(CPC_USB_T *card)
-{
- if (card) {
- if (card->chan) {
- if (card->chan->buf)
- vfree(card->chan->buf);
-
- if (card->chan->CPCWait_q)
- kfree(card->chan->CPCWait_q);
-
- kfree(card->chan);
- }
-
- CPCUSB_Table[card->idx] = NULL;
- kfree(card);
- }
-}
-
-/*
- * setup the interrupt IN endpoint of a specific CPC-USB device
- */
-static int cpcusb_setup_intrep(CPC_USB_T *card)
-{
- int retval = 0;
- struct usb_endpoint_descriptor *ep;
-
- ep = &card->interface->altsetting[0].endpoint[card->num_intr_in].desc;
-
- card->intr_in_buffer[0] = 0;
- card->free_slots = 15; /* initial size */
-
- /* setup the urb */
- usb_fill_int_urb(card->intr_in_urb, card->udev,
- usb_rcvintpipe(card->udev, card->num_intr_in),
- card->intr_in_buffer,
- sizeof(card->intr_in_buffer),
- cpcusb_read_interrupt_callback,
- card,
- ep->bInterval);
-
- card->intr_in_urb->status = 0; /* needed! */
-
- /* submit the urb */
- retval = usb_submit_urb(card->intr_in_urb, GFP_KERNEL);
-
- if (retval)
- err("%s - failed submitting intr urb, error %d", __func__,
- retval);
-
- return retval;
-}
-
-static int cpcusb_open(struct inode *inode, struct file *file)
-{
- CPC_USB_T *card = NULL;
- struct usb_interface *interface;
- int subminor;
- int j, retval = 0;
-
- subminor = iminor(inode);
-
- /* prevent disconnects */
- down(&disconnect_sem);
-
- interface = usb_find_interface(&cpcusb_driver, subminor);
- if (!interface) {
- err("%s - error, can't find device for minor %d",
- __func__, subminor);
- retval = CPC_ERR_NO_INTERFACE_PRESENT;
- goto exit_no_device;
- }
-
- card = usb_get_intfdata(interface);
- if (!card) {
- retval = CPC_ERR_NO_INTERFACE_PRESENT;
- goto exit_no_device;
- }
-
- /* lock this device */
- down(&card->sem);
-
- /* increment our usage count for the driver */
- if (card->open) {
- dbg("device already opened");
- retval = CPC_ERR_CHANNEL_ALREADY_OPEN;
- goto exit_on_error;
- }
-
- /* save our object in the file's private structure */
- file->private_data = card;
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- usb_fill_bulk_urb(card->urbs[j].urb, card->udev,
- usb_rcvbulkpipe(card->udev, card->num_bulk_in),
- card->urbs[j].buffer, card->urbs[j].size,
- cpcusb_read_bulk_callback, card);
-
- retval = usb_submit_urb(card->urbs[j].urb, GFP_KERNEL);
-
- if (retval) {
- err("%s - failed submitting read urb, error %d",
- __func__, retval);
- retval = CPC_ERR_TRANSMISSION_FAILED;
- goto exit_on_error;
- }
- }
-
- info("%s - %d URB's submitted", __func__, j);
-
- ResetBuffer(card->chan);
-
- cpcusb_setup_intrep(card);
- card->open = 1;
-
- atomic_inc(&useCount);
-
-exit_on_error:
- /* unlock this device */
- up(&card->sem);
-
-exit_no_device:
- up(&disconnect_sem);
-
- return retval;
-}
-
-static unsigned int cpcusb_poll(struct file *file, poll_table * wait)
-{
- CPC_USB_T *card = (CPC_USB_T *) file->private_data;
- unsigned int retval = 0;
-
- if (!card) {
- err("%s - device object lost", __func__);
- return -EIO;
- }
-
- poll_wait(file, card->chan->CPCWait_q, wait);
-
- if (IsBufferNotEmpty(card->chan) || !(card->present))
- retval |= (POLLIN | POLLRDNORM);
-
- if (card->free_slots)
- retval |= (POLLOUT | POLLWRNORM);
-
- return retval;
-}
-
-static int cpcusb_release(struct inode *inode, struct file *file)
-{
- CPC_USB_T *card = (CPC_USB_T *) file->private_data;
- int j, retval = 0;
-
- if (card == NULL) {
- dbg("%s - object is NULL", __func__);
- return CPC_ERR_NO_INTERFACE_PRESENT;
- }
-
- /* lock our device */
- down(&card->sem);
-
- if (!card->open) {
- dbg("%s - device not opened", __func__);
- retval = CPC_ERR_NO_INTERFACE_PRESENT;
- goto exit_not_opened;
- }
-
- /* if device wasn't unplugged kill all urbs */
- if (card->present) {
- /* kill read urbs */
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- usb_kill_urb(card->urbs[j].urb);
- }
-
- /* kill irq urb */
- usb_kill_urb(card->intr_in_urb);
-
- /* kill write urbs */
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- if (atomic_read(&card->wrUrbs[j].busy)) {
- usb_kill_urb(card->wrUrbs[j].urb);
- wait_for_completion(&card->wrUrbs[j].finished);
- }
- }
- }
-
- atomic_dec(&useCount);
-
- /* last process detached */
- if (atomic_read(&useCount) == 0) {
- wake_up(&rmmodWq);
- }
-
- if (!card->present && card->open) {
- /* the device was unplugged before the file was released */
- up(&card->sem);
- cpcusb_delete(card);
- return 0;
- }
-
- card->open = 0;
-
-exit_not_opened:
- up(&card->sem);
-
- return 0;
-}
-
-static ssize_t cpcusb_read(struct file *file, char *buffer, size_t count,
- loff_t *ppos)
-{
- CPC_USB_T *card = (CPC_USB_T *) file->private_data;
- CPC_CHAN_T *chan;
- int retval = 0;
-
- if (count < sizeof(CPC_MSG_T))
- return CPC_ERR_UNKNOWN;
-
- /* check if can read from the given address */
- if (!access_ok(VERIFY_WRITE, buffer, count))
- return CPC_ERR_UNKNOWN;
-
- /* lock this object */
- down(&card->sem);
-
- /* verify that the device wasn't unplugged */
- if (!card->present) {
- up(&card->sem);
- return CPC_ERR_NO_INTERFACE_PRESENT;
- }
-
- if (IsBufferEmpty(card->chan)) {
- retval = 0;
- } else {
- chan = card->chan;
-
-#if 0
- /* convert LPC2119 params back to SJA1000 params */
- if (card->deviceRevision >= 0x0200
- && chan->buf[chan->oidx].type == CPC_MSG_T_CAN_PRMS) {
- LPC2119_TO_SJA1000_Params(&chan->buf[chan->oidx]);
- }
-#endif
-
- if (copy_to_user(buffer, &chan->buf[chan->oidx], count) != 0) {
- retval = CPC_ERR_IO_TRANSFER;
- } else {
- chan->oidx = (chan->oidx + 1) % CPC_MSG_BUF_CNT;
- chan->WnR = 1;
- retval = sizeof(CPC_MSG_T);
- }
- }
-/* spin_unlock_irqrestore(&card->slock, flags); */
-
- /* unlock the device */
- up(&card->sem);
-
- return retval;
-}
-
-#define SHIFT 1
-static inline void cpcusb_align_buffer_alignment(unsigned char *buf)
-{
- /* CPC-USB uploads packed bytes. */
- CPC_MSG_T *cpc = (CPC_MSG_T *) buf;
- unsigned int i;
-
- for (i = 0; i < cpc->length + (2 * sizeof(unsigned long)); i++) {
- ((unsigned char *) &cpc->msgid)[1 + i] =
- ((unsigned char *) &cpc->msgid)[1 + SHIFT + i];
- }
-}
-
-static int cpc_get_buffer_count(CPC_CHAN_T *chan)
-{
- /* check the buffer parameters */
- if (chan->iidx == chan->oidx)
- return !chan->WnR ? CPC_MSG_BUF_CNT : 0;
- else if (chan->iidx >= chan->oidx)
- return (chan->iidx - chan->oidx) % CPC_MSG_BUF_CNT;
-
- return (chan->iidx + CPC_MSG_BUF_CNT - chan->oidx) % CPC_MSG_BUF_CNT;
-}
-
-static ssize_t cpcusb_write(struct file *file, const char *buffer,
- size_t count, loff_t *ppos)
-{
- CPC_USB_T *card = (CPC_USB_T *) file->private_data;
- CPC_USB_WRITE_URB_T *wrUrb = NULL;
-
- ssize_t bytes_written = 0;
- int retval = 0;
- int j;
-
- unsigned char *obuf = NULL;
- unsigned char type = 0;
- CPC_MSG_T *info = NULL;
-
- dbg("%s - entered minor %d, count = %zu, present = %d",
- __func__, card->minor, count, card->present);
-
- if (count > sizeof(CPC_MSG_T))
- return CPC_ERR_UNKNOWN;
-
- /* check if can read from the given address */
- if (!access_ok(VERIFY_READ, buffer, count))
- return CPC_ERR_UNKNOWN;
-
- /* lock this object */
- down(&card->sem);
-
- /* verify that the device wasn't unplugged */
- if (!card->present) {
- retval = CPC_ERR_NO_INTERFACE_PRESENT;
- goto exit;
- }
-
- /* verify that we actually have some data to write */
- if (count == 0) {
- dbg("%s - write request of 0 bytes", __func__);
- goto exit;
- }
-
- if (card->free_slots <= 5) {
- info = (CPC_MSG_T *) buffer;
-
- if (info->type != CPC_CMD_T_CLEAR_CMD_QUEUE
- || card->free_slots <= 0) {
- dbg("%s - send buffer full please try again %d",
- __func__, card->free_slots);
- retval = CPC_ERR_CAN_NO_TRANSMIT_BUF;
- goto exit;
- }
- }
-
- /* Find a free write urb */
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- if (!atomic_read(&card->wrUrbs[j].busy)) {
- wrUrb = &card->wrUrbs[j]; /* remember found URB */
- atomic_set(&wrUrb->busy, 1); /* lock this URB */
- init_completion(&wrUrb->finished); /* init completion */
- dbg("WR URB no. %d started", j);
- break;
- }
- }
-
- /* don't found write urb say error */
- if (!wrUrb) {
- dbg("%s - no free send urb available", __func__);
- retval = CPC_ERR_CAN_NO_TRANSMIT_BUF;
- goto exit;
- }
- dbg("URB write req");
-
- obuf = (unsigned char *) wrUrb->urb->transfer_buffer;
-
- /* copy the data from userspace into our transfer buffer;
- * this is the only copy required.
- */
- if (copy_from_user(&obuf[4], buffer, count) != 0) {
- atomic_set(&wrUrb->busy, 0); /* release urb */
- retval = CPC_ERR_IO_TRANSFER;
- goto exit;
- }
-
- /* check if it is a DRIVER information message, so we can
- * response to that message and not the USB
- */
- info = (CPC_MSG_T *) &obuf[4];
-
- bytes_written = 11 + info->length;
- if (bytes_written >= wrUrb->size) {
- retval = CPC_ERR_IO_TRANSFER;
- goto exit;
- }
-
- switch (info->type) {
- case CPC_CMD_T_CLEAR_MSG_QUEUE:
- ResetBuffer(card->chan);
- break;
-
- case CPC_CMD_T_INQ_MSG_QUEUE_CNT:
- retval = cpc_get_buffer_count(card->chan);
- atomic_set(&wrUrb->busy, 0);
-
- goto exit;
-
- case CPC_CMD_T_INQ_INFO:
- if (info->msg.info.source == CPC_INFOMSG_T_DRIVER) {
- /* release urb cause we'll use it for driver
- * information
- */
- atomic_set(&wrUrb->busy, 0);
- if (IsBufferFull(card->chan)) {
- retval = CPC_ERR_IO_TRANSFER;
- goto exit;
- }
-
- /* it is a driver information request message and we have
- * free rx slots to store the response
- */
- type = info->msg.info.type;
- info = &card->chan->buf[card->chan->iidx];
-
- info->type = CPC_MSG_T_INFO;
- info->msg.info.source = CPC_INFOMSG_T_DRIVER;
- info->msg.info.type = type;
-
- switch (type) {
- case CPC_INFOMSG_T_VERSION:
- info->length = strlen(CPC_DRIVER_VERSION) + 2;
- sprintf(info->msg.info.msg, "%s\n",
- CPC_DRIVER_VERSION);
- break;
-
- case CPC_INFOMSG_T_SERIAL:
- info->length = strlen(CPC_DRIVER_SERIAL) + 2;
- sprintf(info->msg.info.msg, "%s\n",
- CPC_DRIVER_SERIAL);
- break;
-
- default:
- info->length = 2;
- info->msg.info.type =
- CPC_INFOMSG_T_UNKNOWN_TYPE;
- }
-
- card->chan->WnR = 0;
- card->chan->iidx =
- (card->chan->iidx + 1) % CPC_MSG_BUF_CNT;
-
- retval = info->length;
- goto exit;
- }
- break;
- case CPC_CMD_T_CAN_PRMS:
- /* Check the controller type. If it's the new CPC-USB, make sure if these are SJA1000 params */
- if (info->msg.canparams.cc_type != SJA1000
- && info->msg.canparams.cc_type != M16C_BASIC
- && (card->productId == USB_CPCUSB_LPC2119_PRODUCT_ID
- && info->msg.canparams.cc_type != SJA1000)) {
- /* don't forget to release the urb */
- atomic_set(&wrUrb->busy, 0);
- retval = CPC_ERR_WRONG_CONTROLLER_TYPE;
- goto exit;
- }
- break;
- }
-
- /* just convert the params if it is an old CPC-USB with M16C controller */
- if (card->productId == USB_CPCUSB_M16C_PRODUCT_ID) {
- /* if it is a parameter message convert it from SJA1000 controller
- * settings to M16C Basic controller settings
- */
- SJA1000_TO_M16C_BASIC_Params((CPC_MSG_T *) &obuf[4]);
- }
-
- /* don't forget the byte alignment */
- cpcusb_align_buffer_alignment(&obuf[4]);
-
- /* setup a the 4 byte header */
- obuf[0] = obuf[1] = obuf[2] = obuf[3] = 0;
-
- /* this urb was already set up, except for this write size */
- wrUrb->urb->transfer_buffer_length = bytes_written + 4;
-
- /* send the data out the bulk port */
- /* a character device write uses GFP_KERNEL,
- unless a spinlock is held */
- retval = usb_submit_urb(wrUrb->urb, GFP_KERNEL);
- if (retval) {
- atomic_set(&wrUrb->busy, 0); /* release urb */
- err("%s - failed submitting write urb, error %d",
- __func__, retval);
- } else {
- retval = bytes_written;
- }
-
-exit:
- /* unlock the device */
- up(&card->sem);
-
- dbg("%s - leaved", __func__);
-
- return retval;
-}
-
-/*
- * callback for interrupt IN urb
- */
-static void cpcusb_read_interrupt_callback(struct urb *urb)
-{
- CPC_USB_T *card = (CPC_USB_T *) urb->context;
- int retval;
- unsigned long flags;
-
- spin_lock_irqsave(&card->slock, flags);
-
- if (!card->present) {
- spin_unlock_irqrestore(&card->slock, flags);
- info("%s - no such device", __func__);
- return;
- }
-
- switch (urb->status) {
- case 0: /* success */
- card->free_slots = card->intr_in_buffer[1];
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* urb was killed */
- spin_unlock_irqrestore(&card->slock, flags);
- dbg("%s - intr urb killed", __func__);
- return;
- default:
- info("%s - nonzero urb status %d", __func__, urb->status);
- break;
- }
-
- retval = usb_submit_urb(urb, GFP_ATOMIC);
- if (retval) {
- err("%s - failed resubmitting intr urb, error %d",
- __func__, retval);
- }
-
- spin_unlock_irqrestore(&card->slock, flags);
- wake_up_interruptible(card->chan->CPCWait_q);
-
- return;
-}
-
-#define UN_SHIFT 1
-#define CPCMSG_HEADER_LEN_FIRMWARE 11
-static inline int cpcusb_unalign_and_copy_buffy(unsigned char *out,
- unsigned char *in)
-{
- unsigned int i, j;
-
- for (i = 0; i < 3; i++)
- out[i] = in[i];
-
- for (j = 0; j < (in[1] + (CPCMSG_HEADER_LEN_FIRMWARE - 3)); j++)
- out[j + i + UN_SHIFT] = in[j + i];
-
- return i + j;
-}
-
-/*
- * callback for bulk IN urb
- */
-static void cpcusb_read_bulk_callback(struct urb *urb)
-{
- CPC_USB_T *card = (CPC_USB_T *) urb->context;
- CPC_CHAN_T *chan;
- unsigned char *ibuf = urb->transfer_buffer;
- int retval, msgCnt, start, again = 0;
- unsigned long flags;
-
- if (!card) {
- err("%s - device object lost", __func__);
- return;
- }
-
- spin_lock_irqsave(&card->slock, flags);
-
- if (!card->present) {
- spin_unlock_irqrestore(&card->slock, flags);
- info("%s - no such device", __func__);
- return;
- }
-
- switch (urb->status) {
- case 0: /* success */
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* urb was killed */
- spin_unlock_irqrestore(&card->slock, flags);
- dbg("%s - read urb killed", __func__);
- return;
- default:
- info("%s - nonzero urb status %d", __func__, urb->status);
- break;
- }
-
- if (urb->actual_length) {
- msgCnt = ibuf[0] & ~0x80;
- again = ibuf[0] & 0x80;
-
- /* we have a 4 byte header */
- start = 4;
- chan = card->chan;
- while (msgCnt) {
- if (!(IsBufferFull(card->chan))) {
- start +=
- cpcusb_unalign_and_copy_buffy((unsigned char *)
- &chan->buf[chan->iidx], &ibuf[start]);
-
- if (start > urb->transfer_buffer_length) {
- err("%d > %d", start, urb->transfer_buffer_length);
- break;
- }
-
- chan->WnR = 0;
- chan->iidx = (chan->iidx + 1) % CPC_MSG_BUF_CNT;
- msgCnt--;
- } else {
- break;
- }
- }
- }
-
- usb_fill_bulk_urb(urb, card->udev,
- usb_rcvbulkpipe(card->udev, card->num_bulk_in),
- urb->transfer_buffer,
- urb->transfer_buffer_length,
- cpcusb_read_bulk_callback, card);
-
- retval = usb_submit_urb(urb, GFP_ATOMIC);
-
- if (retval) {
- err("%s - failed resubmitting read urb, error %d", __func__, retval);
- }
-
- spin_unlock_irqrestore(&card->slock, flags);
-
- wake_up_interruptible(card->chan->CPCWait_q);
-}
-
-/*
- * callback for bulk IN urb
- */
-static void cpcusb_write_bulk_callback(struct urb *urb)
-{
- CPC_USB_T *card = (CPC_USB_T *) urb->context;
- unsigned long flags;
- int j;
-
- spin_lock_irqsave(&card->slock, flags);
-
- /* find this urb */
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- if (card->wrUrbs[j].urb == urb) {
- dbg("URB found no. %d", j);
- /* notify anyone waiting that the write has finished */
- complete(&card->wrUrbs[j].finished);
- atomic_set(&card->wrUrbs[j].busy, 0);
- break;
- }
- }
-
- switch (urb->status) {
- case 0: /* success */
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* urb was killed */
- spin_unlock_irqrestore(&card->slock, flags);
- dbg("%s - write urb no. %d killed", __func__, j);
- return;
- default:
- info("%s - nonzero urb status %d", __func__, urb->status);
- break;
- }
-
- spin_unlock_irqrestore(&card->slock, flags);
-
- wake_up_interruptible(card->chan->CPCWait_q);
-}
-
-static inline int cpcusb_get_free_slot(void)
-{
- int i;
-
- for (i = 0; i < CPC_USB_CARD_CNT; i++) {
- if (!CPCUSB_Table[i])
- return i;
- }
-
- return -1;
-}
-
-/*
- * probe function for new CPC-USB devices
- */
-static int cpcusb_probe(struct usb_interface *interface,
- const struct usb_device_id *id)
-{
- CPC_USB_T *card = NULL;
- CPC_CHAN_T *chan = NULL;
-
- struct usb_device *udev = interface_to_usbdev(interface);
- struct usb_host_interface *iface_desc;
- struct usb_endpoint_descriptor *endpoint;
-
- int i, j, retval = -ENOMEM, slot;
-
- slot = cpcusb_get_free_slot();
- if (slot < 0) {
- info("No more devices supported");
- return -ENOMEM;
- }
-
- /* allocate memory for our device state and initialize it */
- card = kzalloc(sizeof(CPC_USB_T), GFP_KERNEL);
- if (!card) {
- err("Out of memory");
- return -ENOMEM;
- }
- CPCUSB_Table[slot] = card;
-
- /* allocate and initialize the channel struct */
- card->chan = kmalloc(sizeof(CPC_CHAN_T), GFP_KERNEL);
- if (!card->chan) {
- kfree(card);
- err("Out of memory");
- return -ENOMEM;
- }
-
- chan = card->chan;
- memset(chan, 0, sizeof(CPC_CHAN_T));
- ResetBuffer(chan);
-
- init_MUTEX(&card->sem);
- spin_lock_init(&card->slock);
-
- card->udev = udev;
- card->interface = interface;
- if (udev->descriptor.iSerialNumber) {
- usb_string(udev, udev->descriptor.iSerialNumber, card->serialNumber,
- 128);
- info("Serial %s", card->serialNumber);
- }
-
- card->productId = udev->descriptor.idProduct;
- info("Product %s",
- card->productId == USB_CPCUSB_LPC2119_PRODUCT_ID ?
- "CPC-USB/ARM7" : "CPC-USB/M16C");
-
- /* set up the endpoint information */
- /* check out the endpoints */
- /* use only the first bulk-in and bulk-out endpoints */
- iface_desc = &interface->altsetting[0];
- for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
- endpoint = &iface_desc->endpoint[i].desc;
-
- if (!card->num_intr_in &&
- (endpoint->bEndpointAddress & USB_DIR_IN) &&
- ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
- == USB_ENDPOINT_XFER_INT)) {
- card->intr_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- card->num_intr_in = 1;
-
- if (!card->intr_in_urb) {
- err("No free urbs available");
- goto error;
- }
-
- dbg("intr_in urb %d", card->num_intr_in);
- }
-
- if (!card->num_bulk_in &&
- (endpoint->bEndpointAddress & USB_DIR_IN) &&
- ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
- == USB_ENDPOINT_XFER_BULK)) {
- card->num_bulk_in = 2;
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- card->urbs[j].size = endpoint->wMaxPacketSize;
- card->urbs[j].urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!card->urbs[j].urb) {
- err("No free urbs available");
- goto error;
- }
- card->urbs[j].buffer =
- usb_buffer_alloc(udev,
- card->urbs[j].size,
- GFP_KERNEL,
- &card->urbs[j].urb->transfer_dma);
- if (!card->urbs[j].buffer) {
- err("Couldn't allocate bulk_in_buffer");
- goto error;
- }
- }
- info("%s - %d reading URB's allocated",
- __func__, CPC_USB_URB_CNT);
- }
-
- if (!card->num_bulk_out &&
- !(endpoint->bEndpointAddress & USB_DIR_IN) &&
- ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
- == USB_ENDPOINT_XFER_BULK)) {
-
- card->num_bulk_out = 2;
-
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- card->wrUrbs[j].size =
- endpoint->wMaxPacketSize;
- card->wrUrbs[j].urb =
- usb_alloc_urb(0, GFP_KERNEL);
- if (!card->wrUrbs[j].urb) {
- err("No free urbs available");
- goto error;
- }
- card->wrUrbs[j].buffer = usb_buffer_alloc(udev,
- card->wrUrbs[j].size, GFP_KERNEL,
- &card->wrUrbs[j].urb->transfer_dma);
-
- if (!card->wrUrbs[j].buffer) {
- err("Couldn't allocate bulk_out_buffer");
- goto error;
- }
-
- usb_fill_bulk_urb(card->wrUrbs[j].urb, udev,
- usb_sndbulkpipe(udev, endpoint->bEndpointAddress),
- card->wrUrbs[j].buffer,
- card->wrUrbs[j].size,
- cpcusb_write_bulk_callback,
- card);
- }
-
- info("%s - %d writing URB's allocated", __func__, CPC_USB_URB_CNT);
- }
- }
-
- if (!(card->num_bulk_in && card->num_bulk_out)) {
- err("Couldn't find both bulk-in and bulk-out endpoints");
- goto error;
- }
-
- /* allow device read, write and ioctl */
- card->present = 1;
-
- /* we can register the device now, as it is ready */
- usb_set_intfdata(interface, card);
- retval = usb_register_dev(interface, &cpcusb_class);
-
- if (retval) {
- /* something prevented us from registering this driver */
- err("Not able to get a minor for this device.");
- usb_set_intfdata(interface, NULL);
- goto error;
- }
-
- card->chan->minor = card->minor = interface->minor;
-
- chan->buf = vmalloc(sizeof(CPC_MSG_T) * CPC_MSG_BUF_CNT);
- if (chan->buf == NULL) {
- err("Out of memory");
- retval = -ENOMEM;
- goto error;
- }
- info("Allocated memory for %d messages (%lu kbytes)",
- CPC_MSG_BUF_CNT, (long unsigned int)(sizeof(CPC_MSG_T) * CPC_MSG_BUF_CNT) / 1000);
- memset(chan->buf, 0, sizeof(CPC_MSG_T) * CPC_MSG_BUF_CNT);
-
- ResetBuffer(chan);
-
- card->chan->CPCWait_q = kmalloc(sizeof(wait_queue_head_t), GFP_KERNEL);
- if (!card->chan->CPCWait_q) {
- err("Out of memory");
- retval = -ENOMEM;
- goto error;
- }
- init_waitqueue_head(card->chan->CPCWait_q);
-
- CPCUSB_Table[slot] = card;
- card->idx = slot;
- CPCUsbCnt++;
-
- /* let the user know what node this device is now attached to */
- info("Device now attached to USB-%d", card->minor);
- return 0;
-
-error:
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- if (card->urbs[j].buffer) {
- usb_buffer_free(card->udev, card->urbs[j].size,
- card->urbs[j].buffer,
- card->urbs[j].urb->transfer_dma);
- card->urbs[j].buffer = NULL;
- }
- if (card->urbs[j].urb) {
- usb_free_urb(card->urbs[j].urb);
- card->urbs[j].urb = NULL;
- }
- }
-
- cpcusb_delete(card);
- return retval;
-}
-
-/*
- * called by the usb core when the device is removed from the system
- */
-static void cpcusb_disconnect(struct usb_interface *interface)
-{
- CPC_USB_T *card = NULL;
- int minor, j;
-
- /* prevent races with open() */
- down(&disconnect_sem);
-
- card = usb_get_intfdata(interface);
- usb_set_intfdata(interface, NULL);
-
- down(&card->sem);
-
- /* prevent device read, write and ioctl */
- card->present = 0;
-
- minor = card->minor;
-
- /* free all urbs and their buffers */
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- /* terminate an ongoing write */
- if (atomic_read(&card->wrUrbs[j].busy)) {
- usb_kill_urb(card->wrUrbs[j].urb);
- wait_for_completion(&card->wrUrbs[j].finished);
- }
- usb_buffer_free(card->udev, card->wrUrbs[j].size,
- card->wrUrbs[j].buffer,
- card->wrUrbs[j].urb->transfer_dma);
- usb_free_urb(card->wrUrbs[j].urb);
- }
- info("%d write URBs freed", CPC_USB_URB_CNT);
-
- /* free all urbs and their buffers */
- for (j = 0; j < CPC_USB_URB_CNT; j++) {
- usb_buffer_free(card->udev, card->urbs[j].size,
- card->urbs[j].buffer,
- card->urbs[j].urb->transfer_dma);
- usb_free_urb(card->urbs[j].urb);
- }
- info("%d read URBs freed", CPC_USB_URB_CNT);
- usb_free_urb(card->intr_in_urb);
-
- /* give back our minor */
- usb_deregister_dev(interface, &cpcusb_class);
-
- up(&card->sem);
-
- /* if the device is opened, cpcusb_release will clean this up */
- if (!card->open)
- cpcusb_delete(card);
- else
- wake_up_interruptible(card->chan->CPCWait_q);
-
- up(&disconnect_sem);
-
- CPCUsbCnt--;
- info("USB-%d now disconnected", minor);
-}
-
-static int __init CPCUsb_Init(void)
-{
- int result, i;
-
- info(DRIVER_DESC " v" DRIVER_VERSION);
- info("Build on " __DATE__ " at " __TIME__);
-
- for (i = 0; i < CPC_USB_CARD_CNT; i++)
- CPCUSB_Table[i] = 0;
-
- /* register this driver with the USB subsystem */
- result = usb_register(&cpcusb_driver);
- if (result) {
- err("usb_register failed. Error number %d", result);
- return result;
- }
-
- procDir = proc_mkdir(CPC_USB_PROC_DIR, NULL);
- if (!procDir) {
- err("Could not create proc entry");
- } else {
- procEntry = create_proc_read_entry("info", 0444, procDir,
- cpcusb_proc_read_info,
- NULL);
- if (!procEntry) {
- err("Could not create proc entry %s", CPC_USB_PROC_DIR "/info");
- remove_proc_entry(CPC_USB_PROC_DIR, NULL);
- procDir = NULL;
- }
- }
-
- return 0;
-}
-
-static void __exit CPCUsb_Exit(void)
-{
- wait_event(rmmodWq, !atomic_read(&useCount));
-
- /* deregister this driver with the USB subsystem */
- usb_deregister(&cpcusb_driver);
-
- if (procDir) {
- if (procEntry)
- remove_proc_entry("info", procDir);
- remove_proc_entry(CPC_USB_PROC_DIR, NULL);
- }
-}
-
-module_init(CPCUsb_Init);
-module_exit(CPCUsb_Exit);
+++ /dev/null
-/*
- * CPC CAN Interface Definitions
- *
- * Copyright (C) 2000-2008 EMS Dr. Thomas Wuensche
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
- */
-#ifndef CPC_HEADER
-#define CPC_HEADER
-
-/*
- * the maximum length of the union members within a CPC_MSG
- * this value can be defined by the customer, but has to be
- * >= 64 bytes
- * however, if not defined before, we set a length of 64 byte
- */
-#if !defined(CPC_MSG_LEN) || (CPC_MSG_LEN < 64)
-#undef CPC_MSG_LEN
-#define CPC_MSG_LEN 64
-#endif
-
-/*
- * Transmission of events from CPC interfaces to PC can be individually
- * controlled per event type. Default state is: don't transmit
- * Control values are constructed by bit-or of Subject and Action
- * and passed to CPC_Control()
- */
-
-/* Control-Values for CPC_Control() Command Subject Selection */
-#define CONTR_CAN_Message 0x04
-#define CONTR_Busload 0x08
-#define CONTR_CAN_State 0x0C
-#define CONTR_SendAck 0x10
-#define CONTR_Filter 0x14
-#define CONTR_CmdQueue 0x18 /* reserved, do not use */
-#define CONTR_BusError 0x1C
-
-/* Control Command Actions */
-#define CONTR_CONT_OFF 0
-#define CONTR_CONT_ON 1
-#define CONTR_SING_ON 2
-/*
- * CONTR_SING_ON doesn't change CONTR_CONT_ON state, so it should be
- * read as: transmit at least once
- */
-
-/* defines for confirmed request */
-#define DO_NOT_CONFIRM 0
-#define DO_CONFIRM 1
-
-/* event flags */
-#define EVENT_READ 0x01
-#define EVENT_WRITE 0x02
-
-/*
- * Messages from CPC to PC contain a message object type field.
- * The following message types are sent by CPC and can be used in
- * handlers, others should be ignored.
- */
-#define CPC_MSG_T_RESYNC 0 /* Normally to be ignored */
-#define CPC_MSG_T_CAN 1 /* CAN data frame */
-#define CPC_MSG_T_BUSLOAD 2 /* Busload message */
-#define CPC_MSG_T_STRING 3 /* Normally to be ignored */
-#define CPC_MSG_T_CONTI 4 /* Normally to be ignored */
-#define CPC_MSG_T_MEM 7 /* Normally not to be handled */
-#define CPC_MSG_T_RTR 8 /* CAN remote frame */
-#define CPC_MSG_T_TXACK 9 /* Send acknowledge */
-#define CPC_MSG_T_POWERUP 10 /* Power-up message */
-#define CPC_MSG_T_CMD_NO 11 /* Normally to be ignored */
-#define CPC_MSG_T_CAN_PRMS 12 /* Actual CAN parameters */
-#define CPC_MSG_T_ABORTED 13 /* Command aborted message */
-#define CPC_MSG_T_CANSTATE 14 /* CAN state message */
-#define CPC_MSG_T_RESET 15 /* used to reset CAN-Controller */
-#define CPC_MSG_T_XCAN 16 /* XCAN data frame */
-#define CPC_MSG_T_XRTR 17 /* XCAN remote frame */
-#define CPC_MSG_T_INFO 18 /* information strings */
-#define CPC_MSG_T_CONTROL 19 /* used for control of interface/driver behaviour */
-#define CPC_MSG_T_CONFIRM 20 /* response type for confirmed requests */
-#define CPC_MSG_T_OVERRUN 21 /* response type for overrun conditions */
-#define CPC_MSG_T_KEEPALIVE 22 /* response type for keep alive conditions */
-#define CPC_MSG_T_CANERROR 23 /* response type for bus error conditions */
-#define CPC_MSG_T_DISCONNECTED 24 /* response type for a disconnected interface */
-#define CPC_MSG_T_ERR_COUNTER 25 /* RX/TX error counter of CAN controller */
-
-#define CPC_MSG_T_FIRMWARE 100 /* response type for USB firmware download */
-
-/*
- * Messages from the PC to the CPC interface contain a command field
- * Most of the command types are wrapped by the library functions and have therefore
- * normally not to be used.
- * However, programmers who wish to circumvent the library and talk directly
- * to the drivers (mainly Linux programmers) can use the following
- * command types:
- */
-#define CPC_CMD_T_CAN 1 /* CAN data frame */
-#define CPC_CMD_T_CONTROL 3 /* used for control of interface/driver behaviour */
-#define CPC_CMD_T_CAN_PRMS 6 /* set CAN parameters */
-#define CPC_CMD_T_CLEARBUF 8 /* clears input queue; this is depricated, use CPC_CMD_T_CLEAR_MSG_QUEUE instead */
-#define CPC_CMD_T_INQ_CAN_PARMS 11 /* inquire actual CAN parameters */
-#define CPC_CMD_T_FILTER_PRMS 12 /* set filter parameter */
-#define CPC_CMD_T_RTR 13 /* CAN remote frame */
-#define CPC_CMD_T_CANSTATE 14 /* CAN state message */
-#define CPC_CMD_T_XCAN 15 /* XCAN data frame */
-#define CPC_CMD_T_XRTR 16 /* XCAN remote frame */
-#define CPC_CMD_T_RESET 17 /* used to reset CAN-Controller */
-#define CPC_CMD_T_INQ_INFO 18 /* miscellanous information strings */
-#define CPC_CMD_T_OPEN_CHAN 19 /* open a channel */
-#define CPC_CMD_T_CLOSE_CHAN 20 /* close a channel */
-#define CPC_CMD_T_CNTBUF 21 /* this is depricated, use CPC_CMD_T_INQ_MSG_QUEUE_CNT instead */
-#define CPC_CMD_T_CAN_EXIT 200 /* exit the CAN (disable interrupts; reset bootrate; reset output_cntr; mode = 1) */
-
-#define CPC_CMD_T_INQ_MSG_QUEUE_CNT CPC_CMD_T_CNTBUF /* inquires the count of elements in the message queue */
-#define CPC_CMD_T_INQ_ERR_COUNTER 25 /* request the CAN controllers error counter */
-#define CPC_CMD_T_CLEAR_MSG_QUEUE CPC_CMD_T_CLEARBUF /* clear CPC_MSG queue */
-#define CPC_CMD_T_CLEAR_CMD_QUEUE 28 /* clear CPC_CMD queue */
-#define CPC_CMD_T_FIRMWARE 100 /* reserved, must not be used */
-#define CPC_CMD_T_USB_RESET 101 /* reserved, must not be used */
-#define CPC_CMD_T_WAIT_NOTIFY 102 /* reserved, must not be used */
-#define CPC_CMD_T_WAIT_SETUP 103 /* reserved, must not be used */
-#define CPC_CMD_T_ABORT 255 /* Normally not to be used */
-
-/* definitions for CPC_MSG_T_INFO information sources */
-#define CPC_INFOMSG_T_UNKNOWN_SOURCE 0
-#define CPC_INFOMSG_T_INTERFACE 1
-#define CPC_INFOMSG_T_DRIVER 2
-#define CPC_INFOMSG_T_LIBRARY 3
-
-/* information types */
-#define CPC_INFOMSG_T_UNKNOWN_TYPE 0
-#define CPC_INFOMSG_T_VERSION 1
-#define CPC_INFOMSG_T_SERIAL 2
-
-/* definitions for controller types */
-#define PCA82C200 1 /* Philips basic CAN controller, replaced by SJA1000 */
-#define SJA1000 2 /* Philips basic CAN controller */
-#define AN82527 3 /* Intel full CAN controller */
-#define M16C_BASIC 4 /* M16C controller running in basic CAN (not full CAN) mode */
-
-/* channel open error codes */
-#define CPC_ERR_NO_FREE_CHANNEL -1 /* no more free space within the channel array */
-#define CPC_ERR_CHANNEL_ALREADY_OPEN -2 /* the channel is already open */
-#define CPC_ERR_CHANNEL_NOT_ACTIVE -3 /* access to a channel not active failed */
-#define CPC_ERR_NO_DRIVER_PRESENT -4 /* no driver at the location searched by the library */
-#define CPC_ERR_NO_INIFILE_PRESENT -5 /* the library could not find the inifile */
-#define CPC_ERR_WRONG_PARAMETERS -6 /* wrong parameters in the inifile */
-#define CPC_ERR_NO_INTERFACE_PRESENT -7 /* 1. The specified interface is not connected */
- /* 2. The interface (mostly CPC-USB) was disconnected upon operation */
-#define CPC_ERR_NO_MATCHING_CHANNEL -8 /* the driver couldn't find a matching channel */
-#define CPC_ERR_NO_BUFFER_AVAILABLE -9 /* the driver couldn't allocate buffer for messages */
-#define CPC_ERR_NO_INTERRUPT -10 /* the requested interrupt couldn't be claimed */
-#define CPC_ERR_NO_MATCHING_INTERFACE -11 /* no interface type related to this channel was found */
-#define CPC_ERR_NO_RESOURCES -12 /* the requested resources could not be claimed */
-#define CPC_ERR_SOCKET -13 /* error concerning TCP sockets */
-
-/* init error codes */
-#define CPC_ERR_WRONG_CONTROLLER_TYPE -14 /* wrong CAN controller type within initialization */
-#define CPC_ERR_NO_RESET_MODE -15 /* the controller could not be set into reset mode */
-#define CPC_ERR_NO_CAN_ACCESS -16 /* the CAN controller could not be accessed */
-
-/* transmit error codes */
-#define CPC_ERR_CAN_WRONG_ID -20 /* the provided CAN id is too big */
-#define CPC_ERR_CAN_WRONG_LENGTH -21 /* the provided CAN length is too long */
-#define CPC_ERR_CAN_NO_TRANSMIT_BUF -22 /* the transmit buffer was occupied */
-#define CPC_ERR_CAN_TRANSMIT_TIMEOUT -23 /* The message could not be sent within a */
- /* specified time */
-
-/* other error codes */
-#define CPC_ERR_SERVICE_NOT_SUPPORTED -30 /* the requested service is not supported by the interface */
-#define CPC_ERR_IO_TRANSFER -31 /* a transmission error down to the driver occurred */
-#define CPC_ERR_TRANSMISSION_FAILED -32 /* a transmission error down to the interface occurred */
-#define CPC_ERR_TRANSMISSION_TIMEOUT -33 /* a timeout occurred within transmission to the interface */
-#define CPC_ERR_OP_SYS_NOT_SUPPORTED -35 /* the operating system is not supported */
-#define CPC_ERR_UNKNOWN -40 /* an unknown error ocurred (mostly IOCTL errors) */
-
-#define CPC_ERR_LOADING_DLL -50 /* the library 'cpcwin.dll' could not be loaded */
-#define CPC_ERR_ASSIGNING_FUNCTION -51 /* the specified function could not be assigned */
-#define CPC_ERR_DLL_INITIALIZATION -52 /* the DLL was not initialized correctly */
-#define CPC_ERR_MISSING_LICFILE -55 /* the file containing the licenses does not exist */
-#define CPC_ERR_MISSING_LICENSE -56 /* a required license was not found */
-
-/* CAN state bit values. Ignore any bits not listed */
-#define CPC_CAN_STATE_BUSOFF 0x80
-#define CPC_CAN_STATE_ERROR 0x40
-
-/* Mask to help ignore undefined bits */
-#define CPC_CAN_STATE_MASK 0xc0
-
-/*
- * CAN-Message representation in a CPC_MS
- * Message object type is CPC_MSG_T_CAN or CPC_MSG_T_RTR
- * or CPC_MSG_T_XCAN or CPC_MSG_T_XRTR
- */
-typedef struct CPC_CAN_MSG {
- u32 id;
- u8 length;
- u8 msg[8];
-} CPC_CAN_MSG_T;
-
-/* representation of the CAN parameters for the PCA82C200 controller */
-typedef struct CPC_PCA82C200_PARAMS {
- u8 acc_code; /* Acceptance-code for receive, Standard: 0 */
- u8 acc_mask; /* Acceptance-mask for receive, Standard: 0xff (everything) */
- u8 btr0; /* Bus-timing register 0 */
- u8 btr1; /* Bus-timing register 1 */
- u8 outp_contr; /* Output-control register */
-} CPC_PCA82C200_PARAMS_T;
-
-/* representation of the CAN parameters for the SJA1000 controller */
-typedef struct CPC_SJA1000_PARAMS {
- u8 mode; /* enables single or dual acceptance filtering */
- u8 acc_code0; /* Acceptance-code for receive, Standard: 0 */
- u8 acc_code1;
- u8 acc_code2;
- u8 acc_code3;
- u8 acc_mask0; /* Acceptance-mask for receive, Standard: 0xff (everything) */
- u8 acc_mask1;
- u8 acc_mask2;
- u8 acc_mask3;
- u8 btr0; /* Bus-timing register 0 */
- u8 btr1; /* Bus-timing register 1 */
- u8 outp_contr; /* Output-control register */
-} CPC_SJA1000_PARAMS_T;
-
-/*
- * representation of the CAN parameters for the M16C controller
- * in basic CAN mode (means no full CAN)
- */
-typedef struct CPC_M16C_BASIC_PARAMS {
- u8 con0;
- u8 con1;
- u8 ctlr0;
- u8 ctlr1;
- u8 clk;
- u8 acc_std_code0;
- u8 acc_std_code1;
- u8 acc_ext_code0;
- u8 acc_ext_code1;
- u8 acc_ext_code2;
- u8 acc_ext_code3;
- u8 acc_std_mask0;
- u8 acc_std_mask1;
- u8 acc_ext_mask0;
- u8 acc_ext_mask1;
- u8 acc_ext_mask2;
- u8 acc_ext_mask3;
-} CPC_M16C_BASIC_PARAMS_T;
-
-/* CAN params message representation */
-typedef struct CPC_CAN_PARAMS {
- u8 cc_type; /* represents the controller type */
- union {
- CPC_M16C_BASIC_PARAMS_T m16c_basic;
- CPC_SJA1000_PARAMS_T sja1000;
- CPC_PCA82C200_PARAMS_T pca82c200;
- } cc_params;
-} CPC_CAN_PARAMS_T;
-
-/* CHAN init params representation */
-typedef struct CPC_CHAN_PARAMS {
- int fd;
-} CPC_CHAN_PARAMS_T;
-
-/* CAN init params message representation */
-typedef struct CPC_INIT_PARAMS {
- CPC_CHAN_PARAMS_T chanparams;
- CPC_CAN_PARAMS_T canparams;
-} CPC_INIT_PARAMS_T;
-
-/* structure for confirmed message handling */
-typedef struct CPC_CONFIRM {
- u8 result; /* error code */
-} CPC_CONFIRM_T;
-
-/* structure for information requests */
-typedef struct CPC_INFO {
- u8 source; /* interface, driver or library */
- u8 type; /* version or serial number */
- char msg[CPC_MSG_LEN - 2]; /* string holding the requested information */
-} CPC_INFO_T;
-
-/*
- * OVERRUN
- * In general two types of overrun may occur.
- * A hardware overrun, where the CAN controller
- * lost a message, because the interrupt was
- * not handled before the next messgae comes in.
- * Or a software overrun, where i.e. a received
- * message could not be stored in the CPC_MSG
- * buffer.
- */
-
-/* After a software overrun has occurred
- * we wait until we have CPC_OVR_GAP slots
- * free in the CPC_MSG buffer.
- */
-#define CPC_OVR_GAP 10
-
-/*
- * Two types of software overrun may occur.
- * A received CAN message or a CAN state event
- * can cause an overrun.
- * Note: A CPC_CMD which would normally store
- * its result immediately in the CPC_MSG
- * queue may fail, because the message queue is full.
- * This will not generate an overrun message, but
- * will halt command execution, until this command
- * is able to store its message in the message queue.
- */
-#define CPC_OVR_EVENT_CAN 0x01
-#define CPC_OVR_EVENT_CANSTATE 0x02
-#define CPC_OVR_EVENT_BUSERROR 0x04
-
-/*
- * If the CAN controller lost a message
- * we indicate it with the highest bit
- * set in the count field.
- */
-#define CPC_OVR_HW 0x80
-
-/* structure for overrun conditions */
-typedef struct {
- u8 event;
- u8 count;
-} CPC_OVERRUN_T;
-
-/*
- * CAN errors
- * Each CAN controller type has different
- * registers to record errors.
- * Therefor a structure containing the specific
- * errors is set up for each controller here
- */
-
-/*
- * SJA1000 error structure
- * see the SJA1000 datasheet for detailed
- * explanation of the registers
- */
-typedef struct CPC_SJA1000_CAN_ERROR {
- u8 ecc; /* error capture code register */
- u8 rxerr; /* RX error counter register */
- u8 txerr; /* TX error counter register */
-} CPC_SJA1000_CAN_ERROR_T;
-
-/*
- * M16C error structure
- * see the M16C datasheet for detailed
- * explanation of the registers
- */
-typedef struct CPC_M16C_CAN_ERROR {
- u8 tbd; /* to be defined */
-} CPC_M16C_CAN_ERROR_T;
-
-/* structure for CAN error conditions */
-#define CPC_CAN_ECODE_ERRFRAME 0x01
-typedef struct CPC_CAN_ERROR {
- u8 ecode;
- struct {
- u8 cc_type; /* CAN controller type */
- union {
- CPC_SJA1000_CAN_ERROR_T sja1000;
- CPC_M16C_CAN_ERROR_T m16c;
- } regs;
- } cc;
-} CPC_CAN_ERROR_T;
-
-/*
- * Structure containing RX/TX error counter.
- * This structure is used to request the
- * values of the CAN controllers TX and RX
- * error counter.
- */
-typedef struct CPC_CAN_ERR_COUNTER {
- u8 rx;
- u8 tx;
-} CPC_CAN_ERR_COUNTER_T;
-
-/* If this flag is set, transmissions from PC to CPC are protected against loss */
-#define CPC_SECURE_TO_CPC 0x01
-
-/* If this flag is set, transmissions from CPC to PC are protected against loss */
-#define CPC_SECURE_TO_PC 0x02
-
-/* If this flag is set, the CAN-transmit buffer is checked to be free before sending a message */
-#define CPC_SECURE_SEND 0x04
-
-/*
- * If this flag is set, the transmission complete flag is checked
- * after sending a message
- * THIS IS CURRENTLY ONLY IMPLEMENTED IN THE PASSIVE INTERFACE DRIVERS
- */
-#define CPC_SECURE_TRANSMIT 0x08
-
-/* main message type used between library and application */
-typedef struct CPC_MSG {
- u8 type; /* type of message */
- u8 length; /* length of data within union 'msg' */
- u8 msgid; /* confirmation handle */
- u32 ts_sec; /* timestamp in seconds */
- u32 ts_nsec; /* timestamp in nano seconds */
- union {
- u8 generic[CPC_MSG_LEN];
- CPC_CAN_MSG_T canmsg;
- CPC_CAN_PARAMS_T canparams;
- CPC_CONFIRM_T confirmation;
- CPC_INFO_T info;
- CPC_OVERRUN_T overrun;
- CPC_CAN_ERROR_T error;
- CPC_CAN_ERR_COUNTER_T err_counter;
- u8 busload;
- u8 canstate;
- } msg;
-} CPC_MSG_T;
-
-#endif /* CPC_HEADER */
+++ /dev/null
-/*
- * CPCLIB
- *
- * Copyright (C) 2000-2008 EMS Dr. Thomas Wuensche
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
- *
- */
-#ifndef CPC_INT_H
-#define CPC_INT_H
-
-#include <linux/wait.h>
-
-#define CPC_MSG_BUF_CNT 1500
-
-#define CPC_PROC_DIR "driver/"
-
-#undef dbg
-#undef err
-#undef info
-
-/* Use our own dbg macro */
-#define dbg(format, arg...) do { if (debug) printk( KERN_INFO format "\n" , ## arg); } while (0)
-#define err(format, arg...) do { printk( KERN_INFO "ERROR " format "\n" , ## arg); } while (0)
-#define info(format, arg...) do { printk( KERN_INFO format "\n" , ## arg); } while (0)
-
-/* Macros help using of our buffers */
-#define IsBufferFull(x) (!(x)->WnR) && ((x)->iidx == (x)->oidx)
-#define IsBufferEmpty(x) ((x)->WnR) && ((x)->iidx == (x)->oidx)
-#define IsBufferNotEmpty(x) (!(x)->WnR) || ((x)->iidx != (x)->oidx)
-#define ResetBuffer(x) do { (x)->oidx = (x)->iidx=0; (x)->WnR = 1; } while(0);
-
-#define CPC_BufWriteAllowed ((chan->oidx != chan->iidx) || chan->WnR)
-
-typedef void (*chan_write_byte_t) (void *chan, unsigned int reg,
- unsigned char val);
-typedef unsigned char (*chan_read_byte_t) (void *chan, unsigned int reg);
-
-typedef struct CPC_CHAN {
- void __iomem * canBase; /* base address of SJA1000 */
- chan_read_byte_t read_byte; /* CAN controller read access routine */
- chan_write_byte_t write_byte; /* CAN controller write access routine */
- CPC_MSG_T *buf; /* buffer for CPC msg */
- unsigned int iidx;
- unsigned int oidx;
- unsigned int WnR;
- unsigned int minor;
- unsigned int locked;
- unsigned int irqDisabled;
-
- unsigned char cpcCtrlCANMessage;
- unsigned char cpcCtrlCANState;
- unsigned char cpcCtrlBUSState;
-
- unsigned char controllerType;
-
- unsigned long ovrTimeSec;
- unsigned long ovrTimeNSec;
- unsigned long ovrLockedBuffer;
- CPC_OVERRUN_T ovr;
-
- /* for debugging only */
- unsigned int handledIrqs;
- unsigned int lostMessages;
-
- unsigned int sentStdCan;
- unsigned int sentExtCan;
- unsigned int sentStdRtr;
- unsigned int sentExtRtr;
-
- unsigned int recvStdCan;
- unsigned int recvExtCan;
- unsigned int recvStdRtr;
- unsigned int recvExtRtr;
-
- wait_queue_head_t *CPCWait_q;
-
- void *private;
-} CPC_CHAN_T;
-
-#endif
+++ /dev/null
-/* Header for CPC-USB Driver ********************
- * Copyright 1999, 2000, 2001
- *
- * Company: EMS Dr. Thomas Wuensche
- * Sonnenhang 3
- * 85304 Ilmmuenster
- * Phone: +49-8441-490260
- * Fax: +49-8441-81860
- * email: support@ems-wuensche.com
- * WWW: www.ems-wuensche.com
- */
-
-#ifndef CPCUSB_H
-#define CPCUSB_H
-
-#undef err
-#undef dbg
-#undef info
-
-/* Use our own dbg macro */
-#define dbg(format, arg...) do { if (debug) printk(KERN_INFO "CPC-USB: " format "\n" , ## arg); } while (0)
-#define info(format, arg...) do { printk(KERN_INFO "CPC-USB: " format "\n" , ## arg); } while (0)
-#define err(format, arg...) do { printk(KERN_INFO "CPC-USB(ERROR): " format "\n" , ## arg); } while (0)
-
-#define CPC_USB_CARD_CNT 4
-
-typedef struct CPC_USB_READ_URB {
- unsigned char *buffer; /* the buffer to send data */
- size_t size; /* the size of the send buffer */
- struct urb *urb; /* the urb used to send data */
-} CPC_USB_READ_URB_T;
-
-typedef struct CPC_USB_WRITE_URB {
- unsigned char *buffer; /* the buffer to send data */
- size_t size; /* the size of the send buffer */
- struct urb *urb; /* the urb used to send data */
- atomic_t busy; /* true if write urb is busy */
- struct completion finished; /* wait for the write to finish */
-} CPC_USB_WRITE_URB_T;
-
-#define CPC_USB_URB_CNT 10
-
-typedef struct CPC_USB {
- struct usb_device *udev; /* save off the usb device pointer */
- struct usb_interface *interface; /* the interface for this device */
- unsigned char minor; /* the starting minor number for this device */
- unsigned char num_ports; /* the number of ports this device has */
- int num_intr_in; /* number of interrupt in endpoints we have */
- int num_bulk_in; /* number of bulk in endpoints we have */
- int num_bulk_out; /* number of bulk out endpoints we have */
-
- CPC_USB_READ_URB_T urbs[CPC_USB_URB_CNT];
-
- unsigned char intr_in_buffer[4]; /* interrupt transfer buffer */
- struct urb *intr_in_urb; /* interrupt transfer urb */
-
- CPC_USB_WRITE_URB_T wrUrbs[CPC_USB_URB_CNT];
-
- int open; /* if the port is open or not */
- int present; /* if the device is not disconnected */
- struct semaphore sem; /* locks this structure */
-
- int free_slots; /* free send slots of CPC-USB */
- int idx;
-
- spinlock_t slock;
-
- char serialNumber[128]; /* serial number */
- int productId; /* product id to differ between M16C and LPC2119 */
- CPC_CHAN_T *chan;
-} CPC_USB_T;
-
-#define CPCTable CPCUSB_Table
-
-#define CPC_DRIVER_VERSION "0.724"
-#define CPC_DRIVER_SERIAL "not applicable"
-
-#define OBUF_SIZE 255 /* 4096 */
-
-/* read timeouts -- RD_NAK_TIMEOUT * RD_EXPIRE = Number of seconds */
-#define RD_NAK_TIMEOUT (10*HZ) /* Default number of X seconds to wait */
-#define RD_EXPIRE 12 /* Number of attempts to wait X seconds */
-
-#define CPC_USB_BASE_MNR 0 /* CPC-USB start at minor 0 */
-
-#endif
+++ /dev/null
-#ifndef _SJA2M16C_H
-#define _SJA2M16C_H
-
-#include "cpc.h"
-
-#define BAUDRATE_TOLERANCE_PERCENT 1
-#define SAMPLEPOINT_TOLERANCE_PERCENT 5
-#define SAMPLEPOINT_UPPER_LIMIT 88
-
-/* M16C parameters */
-struct FIELD_C0CONR {
- unsigned int brp:4;
- unsigned int sam:1;
- unsigned int pr:3;
- unsigned int dummy:8;
-};
-struct FIELD_C1CONR {
- unsigned int ph1:3;
- unsigned int ph2:3;
- unsigned int sjw:2;
- unsigned int dummy:8;
-};
-typedef union C0CONR {
- unsigned char c0con;
- struct FIELD_C0CONR bc0con;
-} C0CONR_T;
-typedef union C1CONR {
- unsigned char c1con;
- struct FIELD_C1CONR bc1con;
-} C1CONR_T;
-
-#define SJA_TSEG1 ((pParams->btr1 & 0x0f)+1)
-#define SJA_TSEG2 (((pParams->btr1 & 0x70)>>4)+1)
-#define SJA_BRP ((pParams->btr0 & 0x3f)+1)
-#define SJA_SJW ((pParams->btr0 & 0xc0)>>6)
-#define SJA_SAM ((pParams->btr1 & 0x80)>>7)
-int baudrate_m16c(int clk, int brp, int pr, int ph1, int ph2);
-int samplepoint_m16c(int brp, int pr, int ph1, int ph2);
-int SJA1000_TO_M16C_BASIC_Params(CPC_MSG_T *pMsg);
-
-#endif
+++ /dev/null
-/****************************************************************************
-*
-* Copyright (c) 2003,2004 by EMS Dr. Thomas Wuensche
-*
-* - All rights reserved -
-*
-* This code is provided "as is" without warranty of any kind, either
-* expressed or implied, including but not limited to the liability
-* concerning the freedom from material defects, the fitness for parti-
-* cular purposes or the freedom of proprietary rights of third parties.
-*
-*****************************************************************************
-* Module name.: cpcusb
-*****************************************************************************
-* Include file: cpc.h
-*****************************************************************************
-* Project.....: Windows Driver Development Kit
-* Filename....: sja2m16c.cpp
-* Authors.....: (GU) Gerhard Uttenthaler
-* (CS) Christian Schoett
-*****************************************************************************
-* Short descr.: converts baudrate between SJA1000 and M16C
-*****************************************************************************
-* Description.: handles the baudrate conversion from SJA1000 parameters to
-* M16C parameters
-*****************************************************************************
-* Address : EMS Dr. Thomas Wuensche
-* Sonnenhang 3
-* D-85304 Ilmmuenster
-* Tel. : +49-8441-490260
-* Fax. : +49-8441-81860
-* email: support@ems-wuensche.com
-*****************************************************************************
-* History
-*****************************************************************************
-* Version Date Auth Remark
-*
-* 01.00 ?? GU - initial release
-* 01.10 ?????????? CS - adapted to fit into the USB Windows driver
-* 02.00 18.08.2004 GU - improved the baudrate calculating algorithm
-* - implemented acceptance filtering
-* 02.10 10.09.2004 CS - adapted to fit into the USB Windows driver
-*****************************************************************************
-* ToDo's
-*****************************************************************************
-*/
-
-/****************************************************************************/
-/* I N C L U D E S
-*/
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/vmalloc.h>
-#include <linux/module.h>
-#include <linux/poll.h>
-#include <linux/smp_lock.h>
-#include <linux/completion.h>
-#include <asm/uaccess.h>
-#include <linux/usb.h>
-
-#include "cpc.h"
-#include "cpc_int.h"
-#include "cpcusb.h"
-
-#include "sja2m16c.h"
-
-/*********************************************************************/
-int baudrate_m16c(int clk, int brp, int pr, int ph1, int ph2)
-{
- return (16000000 / (1 << clk)) / 2 / (brp + 1) / (1 + pr + 1 +
- ph1 + 1 + ph2 +
- 1);
-}
-
-
-/*********************************************************************/
-int samplepoint_m16c(int brp, int pr, int ph1, int ph2)
-{
- return (100 * (1 + pr + 1 + ph1 + 1)) / (1 + pr + 1 + ph1 + 1 +
- ph2 + 1);
-}
-
-
-/****************************************************************************
-* Function.....: SJA1000_TO_M16C_BASIC_Params
-*
-* Task.........: This routine converts SJA1000 CAN btr parameters into M16C
-* parameters based on the sample point and the error. In
-* addition it converts the acceptance filter parameters to
-* suit the M16C parameters
-*
-* Parameters...: None
-*
-* Return values: None
-*
-* Comments.....:
-*****************************************************************************
-* History
-*****************************************************************************
-* 19.01.2005 CS - modifed the conversion of SJA1000 filter params into
-* M16C params. Due to compatibility reasons with the
-* older 82C200 CAN controller the SJA1000
-****************************************************************************/
-int SJA1000_TO_M16C_BASIC_Params(CPC_MSG_T * in)
-{
- int sjaBaudrate;
- int sjaSamplepoint;
- int *baudrate_error; // BRP[0..15], PR[0..7], PH1[0..7], PH2[0..7]
- int *samplepoint_error; // BRP[0..15], PR[0..7], PH1[0..7], PH2[0..7]
- int baudrate_error_merk;
- int clk, brp, pr, ph1, ph2;
- int clk_merk, brp_merk, pr_merk, ph1_merk, ph2_merk;
- int index;
- unsigned char acc_code0, acc_code1, acc_code2, acc_code3;
- unsigned char acc_mask0, acc_mask1, acc_mask2, acc_mask3;
- CPC_MSG_T * out;
- C0CONR_T c0con;
- C1CONR_T c1con;
- int tmpAccCode;
- int tmpAccMask;
-
- // we have to convert the parameters into M16C parameters
- CPC_SJA1000_PARAMS_T * pParams;
-
- // check if the type is CAN parameters and if we have to convert the given params
- if (in->type != CPC_CMD_T_CAN_PRMS
- || in->msg.canparams.cc_type != SJA1000)
- return 0;
- pParams =
- (CPC_SJA1000_PARAMS_T *) & in->msg.canparams.cc_params.sja1000;
- acc_code0 = pParams->acc_code0;
- acc_code1 = pParams->acc_code1;
- acc_code2 = pParams->acc_code2;
- acc_code3 = pParams->acc_code3;
- acc_mask0 = pParams->acc_mask0;
- acc_mask1 = pParams->acc_mask1;
- acc_mask2 = pParams->acc_mask2;
- acc_mask3 = pParams->acc_mask3;
-
-#ifdef _DEBUG_OUTPUT_CAN_PARAMS
- info("acc_code0: %2.2Xh\n", acc_code0);
- info("acc_code1: %2.2Xh\n", acc_code1);
- info("acc_code2: %2.2Xh\n", acc_code2);
- info("acc_code3: %2.2Xh\n", acc_code3);
- info("acc_mask0: %2.2Xh\n", acc_mask0);
- info("acc_mask1: %2.2Xh\n", acc_mask1);
- info("acc_mask2: %2.2Xh\n", acc_mask2);
- info("acc_mask3: %2.2Xh\n", acc_mask3);
-
-#endif /* */
- if (!
- (baudrate_error =
- (int *) vmalloc(sizeof(int) * 16 * 8 * 8 * 8 * 5))) {
- err("Could not allocate memory\n");
- return -3;
- }
- if (!
- (samplepoint_error =
- (int *) vmalloc(sizeof(int) * 16 * 8 * 8 * 8 * 5))) {
- err("Could not allocate memory\n");
- vfree(baudrate_error);
- return -3;
- }
- memset(baudrate_error, 0xff, sizeof(baudrate_error));
- memset(samplepoint_error, 0xff, sizeof(baudrate_error));
- sjaBaudrate =
- 16000000 / 2 / SJA_BRP / (1 + SJA_TSEG1 + SJA_TSEG2);
- sjaSamplepoint =
- 100 * (1 + SJA_TSEG1) / (1 + SJA_TSEG1 + SJA_TSEG2);
- if (sjaBaudrate == 0) {
- vfree(baudrate_error);
- vfree(samplepoint_error);
- return -2;
- }
-
-#ifdef _DEBUG_OUTPUT_CAN_PARAMS
- info("\nStarting SJA CAN params\n");
- info("-------------------------\n");
- info("TS1 : %2.2Xh TS2 : %2.2Xh\n", SJA_TSEG1, SJA_TSEG2);
- info("BTR0 : %2.2Xh BTR1: %2.2Xh\n", pParams->btr0,
- pParams->btr1);
- info("Baudrate: %d.%dkBaud\n", sjaBaudrate / 1000,
- sjaBaudrate % 1000);
- info("Sample P: 0.%d\n", sjaSamplepoint);
- info("\n");
-
-#endif /* */
- c0con.bc0con.sam = SJA_SAM;
- c1con.bc1con.sjw = SJA_SJW;
-
- // calculate errors for all baudrates
- index = 0;
- for (clk = 0; clk < 5; clk++) {
- for (brp = 0; brp < 16; brp++) {
- for (pr = 0; pr < 8; pr++) {
- for (ph1 = 0; ph1 < 8; ph1++) {
- for (ph2 = 0; ph2 < 8; ph2++) {
- baudrate_error[index] =
- 100 *
- abs(baudrate_m16c
- (clk, brp, pr, ph1,
- ph2) -
- sjaBaudrate) /
- sjaBaudrate;
- samplepoint_error[index] =
- abs(samplepoint_m16c
- (brp, pr, ph1,
- ph2) -
- sjaSamplepoint);
-
-#if 0
- info
- ("Baudrate : %d kBaud\n",
- baudrate_m16c(clk,
- brp, pr,
- ph1,
- ph2));
- info
- ("Baudrate Error: %d\n",
- baudrate_error
- [index]);
- info
- ("Sample P Error: %d\n",
- samplepoint_error
- [index]);
- info
- ("clk : %d\n",
- clk);
-
-#endif /* */
- index++;
- }
- }
- }
- }
- }
-
- // mark all baudrate_error entries which are outer limits
- index = 0;
- for (clk = 0; clk < 5; clk++) {
- for (brp = 0; brp < 16; brp++) {
- for (pr = 0; pr < 8; pr++) {
- for (ph1 = 0; ph1 < 8; ph1++) {
- for (ph2 = 0; ph2 < 8; ph2++) {
- if ((baudrate_error[index]
- >
- BAUDRATE_TOLERANCE_PERCENT)
- ||
- (samplepoint_error
- [index] >
- SAMPLEPOINT_TOLERANCE_PERCENT)
- ||
- (samplepoint_m16c
- (brp, pr, ph1,
- ph2) >
- SAMPLEPOINT_UPPER_LIMIT))
- {
- baudrate_error
- [index] = -1;
- } else
- if (((1 + pr + 1 +
- ph1 + 1 + ph2 +
- 1) < 8)
- ||
- ((1 + pr + 1 +
- ph1 + 1 + ph2 +
- 1) > 25)) {
- baudrate_error
- [index] = -1;
- }
-
-#if 0
- else {
- info
- ("Baudrate : %d kBaud\n",
- baudrate_m16c
- (clk, brp, pr,
- ph1, ph2));
- info
- ("Baudrate Error: %d\n",
- baudrate_error
- [index]);
- info
- ("Sample P Error: %d\n",
- samplepoint_error
- [index]);
- }
-
-#endif /* */
- index++;
- }
- }
- }
- }
- }
-
- // find list of minimum of baudrate_error within unmarked entries
- clk_merk = brp_merk = pr_merk = ph1_merk = ph2_merk = 0;
- baudrate_error_merk = 100;
- index = 0;
- for (clk = 0; clk < 5; clk++) {
- for (brp = 0; brp < 16; brp++) {
- for (pr = 0; pr < 8; pr++) {
- for (ph1 = 0; ph1 < 8; ph1++) {
- for (ph2 = 0; ph2 < 8; ph2++) {
- if (baudrate_error[index]
- != -1) {
- if (baudrate_error
- [index] <
- baudrate_error_merk)
- {
- baudrate_error_merk
- =
- baudrate_error
- [index];
- brp_merk =
- brp;
- pr_merk =
- pr;
- ph1_merk =
- ph1;
- ph2_merk =
- ph2;
- clk_merk =
- clk;
-
-#if 0
- info
- ("brp: %2.2Xh pr: %2.2Xh ph1: %2.2Xh ph2: %2.2Xh\n",
- brp,
- pr,
- ph1,
- ph2);
- info
- ("Baudrate : %d kBaud\n",
- baudrate_m16c
- (clk,
- brp,
- pr,
- ph1,
- ph2));
- info
- ("Baudrate Error: %d\n",
- baudrate_error
- [index]);
- info
- ("Sample P Error: %d\n",
- samplepoint_error
- [index]);
-
-#endif /* */
- }
- }
- index++;
- }
- }
- }
- }
- }
- if (baudrate_error_merk == 100) {
- info("ERROR: Could not convert CAN init parameter\n");
- vfree(baudrate_error);
- vfree(samplepoint_error);
- return -1;
- }
-
- // setting m16c CAN parameter
- c0con.bc0con.brp = brp_merk;
- c0con.bc0con.pr = pr_merk;
- c1con.bc1con.ph1 = ph1_merk;
- c1con.bc1con.ph2 = ph2_merk;
-
-#ifdef _DEBUG_OUTPUT_CAN_PARAMS
- info("\nResulting M16C CAN params\n");
- info("-------------------------\n");
- info("clk : %2.2Xh\n", clk_merk);
- info("ph1 : %2.2Xh ph2: %2.2Xh\n", c1con.bc1con.ph1 + 1,
- c1con.bc1con.ph2 + 1);
- info("pr : %2.2Xh brp: %2.2Xh\n", c0con.bc0con.pr + 1,
- c0con.bc0con.brp + 1);
- info("sjw : %2.2Xh sam: %2.2Xh\n", c1con.bc1con.sjw,
- c0con.bc0con.sam);
- info("co1 : %2.2Xh co0: %2.2Xh\n", c1con.c1con, c0con.c0con);
- info("Baudrate: %d.%dBaud\n",
- baudrate_m16c(clk_merk, c0con.bc0con.brp, c0con.bc0con.pr,
- c1con.bc1con.ph1, c1con.bc1con.ph2) / 1000,
- baudrate_m16c(clk_merk, c0con.bc0con.brp, c0con.bc0con.pr,
- c1con.bc1con.ph1, c1con.bc1con.ph2) % 1000);
- info("Sample P: 0.%d\n",
- samplepoint_m16c(c0con.bc0con.brp, c0con.bc0con.pr,
- c1con.bc1con.ph1, c1con.bc1con.ph2));
- info("\n");
-
-#endif /* */
- out = in;
- out->type = 6;
- out->length = sizeof(CPC_M16C_BASIC_PARAMS_T) + 1;
- out->msg.canparams.cc_type = M16C_BASIC;
- out->msg.canparams.cc_params.m16c_basic.con0 = c0con.c0con;
- out->msg.canparams.cc_params.m16c_basic.con1 = c1con.c1con;
- out->msg.canparams.cc_params.m16c_basic.ctlr0 = 0x4C;
- out->msg.canparams.cc_params.m16c_basic.ctlr1 = 0x00;
- out->msg.canparams.cc_params.m16c_basic.clk = clk_merk;
- out->msg.canparams.cc_params.m16c_basic.acc_std_code0 =
- acc_code0;
- out->msg.canparams.cc_params.m16c_basic.acc_std_code1 = acc_code1;
-
-// info("code0: 0x%2.2X, code1: 0x%2.2X\n", out->msg.canparams.cc_params.m16c_basic.acc_std_code0, out->msg.canparams.cc_params.m16c_basic.acc_std_code1);
- tmpAccCode = (acc_code1 >> 5) + (acc_code0 << 3);
- out->msg.canparams.cc_params.m16c_basic.acc_std_code0 =
- (unsigned char) tmpAccCode;
- out->msg.canparams.cc_params.m16c_basic.acc_std_code1 =
- (unsigned char) (tmpAccCode >> 8);
-
-// info("code0: 0x%2.2X, code1: 0x%2.2X\n", out->msg.canparams.cc_params.m16c_basic.acc_std_code0, out->msg.canparams.cc_params.m16c_basic.acc_std_code1);
- out->msg.canparams.cc_params.m16c_basic.acc_std_mask0 =
- ~acc_mask0;
- out->msg.canparams.cc_params.m16c_basic.acc_std_mask1 =
- ~acc_mask1;
-
-// info("mask0: 0x%2.2X, mask1: 0x%2.2X\n", out->msg.canparams.cc_params.m16c_basic.acc_std_mask0, out->msg.canparams.cc_params.m16c_basic.acc_std_mask1);
- tmpAccMask = ((acc_mask1) >> 5) + ((acc_mask0) << 3);
-
-// info("tmpAccMask: 0x%4.4X\n", tmpAccMask);
- out->msg.canparams.cc_params.m16c_basic.acc_std_mask0 =
- (unsigned char) ~tmpAccMask;
- out->msg.canparams.cc_params.m16c_basic.acc_std_mask1 =
- (unsigned char) ~(tmpAccMask >> 8);
-
-// info("mask0: 0x%2.2X, mask1: 0x%2.2X\n", out->msg.canparams.cc_params.m16c_basic.acc_std_mask0, out->msg.canparams.cc_params.m16c_basic.acc_std_mask1);
- out->msg.canparams.cc_params.m16c_basic.acc_ext_code0 =
- (unsigned char) tmpAccCode;
- out->msg.canparams.cc_params.m16c_basic.acc_ext_code1 =
- (unsigned char) (tmpAccCode >> 8);
- out->msg.canparams.cc_params.m16c_basic.acc_ext_code2 = acc_code2;
- out->msg.canparams.cc_params.m16c_basic.acc_ext_code3 = acc_code3;
- out->msg.canparams.cc_params.m16c_basic.acc_ext_mask0 =
- (unsigned char) ~tmpAccMask;
- out->msg.canparams.cc_params.m16c_basic.acc_ext_mask1 =
- (unsigned char) ~(tmpAccMask >> 8);
- out->msg.canparams.cc_params.m16c_basic.acc_ext_mask2 =
- ~acc_mask2;
- out->msg.canparams.cc_params.m16c_basic.acc_ext_mask3 =
- ~acc_mask3;
- vfree(baudrate_error);
- vfree(samplepoint_error);
- return 0;
-}
-
-
struct dst_node *n = q->queuedata;
int err = -EIO;
- if (bio_empty_barrier(bio) && !q->prepare_discard_fn) {
+ if (bio_empty_barrier(bio) && !blk_queue_discard(q)) {
/*
* This is a dirty^Wnice hack, but if we complete this
* operation with -EOPNOTSUPP like intended, XFS
/*
* Configuration parser.
*/
-static void cn_dst_callback(struct cn_msg *msg)
+static void cn_dst_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
struct dst_ctl *ctl;
int err;
struct dst_node *n = NULL, *tmp;
unsigned int hash;
+ if (!cap_raised(nsp->eff_cap, CAP_SYS_ADMIN)) {
+ err = -EPERM;
+ goto out;
+ }
+
if (msg->len < sizeof(struct dst_ctl)) {
err = -EBADMSG;
goto out;
EXTRA_CFLAGS += -Idrivers/media/dvb/frontends
EXTRA_CFLAGS += -Idrivers/media/dvb/dvb-core
-
-# Ubuntu 8.04 has CONFIG_SND undefined, so include lum sound/config.h too
-ifeq ($(CONFIG_SND),)
-EXTRA_CFLAGS += -include sound/config.h
-endif
return tsl2561_powerdown(client);
}
-static unsigned short normal_i2c[] = { 0x29, 0x39, 0x49, I2C_CLIENT_END };
-
-I2C_CLIENT_INSMOD;
-
static const struct i2c_device_id tsl2561_id[] = {
{ "tsl2561", 0 },
{ }
return err;
}
-static void pohmelfs_cn_callback(struct cn_msg *msg)
+static void pohmelfs_cn_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
int err;
+ if (!cap_raised(nsp->eff_cap, CAP_SYS_ADMIN))
+ return;
+
switch (msg->flags) {
case POHMELFS_FLAGS_ADD:
case POHMELFS_FLAGS_DEL:
return 0;
}
-static struct vm_operations_struct uio_vm_ops = {
+static const struct vm_operations_struct uio_vm_ops = {
.open = uio_vma_open,
.close = uio_vma_close,
.fault = uio_vma_fault,
default y if PCMCIA && !M32R # sl811_cs
default y if ARM # SL-811
default y if SUPERH # r8a66597-hcd
- default y if MICROBLAZE
default PCI
# many non-PCI SOC chips embed OHCI
return retval;
}
-static struct file_operations fops = {
+static const struct file_operations fops = {
.owner = THIS_MODULE,
.read = usbtmc_read,
.write = usbtmc_write,
#include <linux/wait.h>
#include <linux/compiler.h>
#include <asm/uaccess.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/poll.h>
#include <linux/smp_lock.h>
}
/* used after endpoint configuration */
-static struct file_operations printer_io_operations = {
+static const struct file_operations printer_io_operations = {
.owner = THIS_MODULE,
.open = printer_open,
.read = printer_read,
return 0;
}
-#ifdef CONFIG_PM
-static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state)
+#ifdef CONFIG_PM
+static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
if (time_before(jiffies, ohci->ohci.next_statechange))
msleep(5);
ohci->ohci.next_statechange = jiffies;
- pxa27x_stop_hc(ohci, &pdev->dev);
+ pxa27x_stop_hc(ohci, dev);
hcd->state = HC_STATE_SUSPENDED;
return 0;
}
-static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev)
+static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
+ struct pxaohci_platform_data *inf = dev->platform_data;
int status;
if (time_before(jiffies, ohci->ohci.next_statechange))
msleep(5);
ohci->ohci.next_statechange = jiffies;
- if ((status = pxa27x_start_hc(ohci, &pdev->dev)) < 0)
+ if ((status = pxa27x_start_hc(ohci, dev)) < 0)
return status;
+ /* Select Power Management Mode */
+ pxa27x_ohci_select_pmm(ohci, inf->port_mode);
+
ohci_finish_controller_resume(hcd);
return 0;
}
+
+static struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
+ .suspend = ohci_hcd_pxa27x_drv_suspend,
+ .resume = ohci_hcd_pxa27x_drv_resume,
+};
#endif
/* work with hotplug and coldplug */
.probe = ohci_hcd_pxa27x_drv_probe,
.remove = ohci_hcd_pxa27x_drv_remove,
.shutdown = usb_hcd_platform_shutdown,
-#ifdef CONFIG_PM
- .suspend = ohci_hcd_pxa27x_drv_suspend,
- .resume = ohci_hcd_pxa27x_drv_resume,
-#endif
.driver = {
.name = "pxa27x-ohci",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &ohci_hcd_pxa27x_pm_ops,
+#endif
},
};
return single_open(file, pzl_print, inode->i_private);
}
-static struct file_operations di_fops = {
+static const struct file_operations di_fops = {
.open = di_open,
.read = seq_read,
.llseek = seq_lseek,
.owner = THIS_MODULE,
};
-static struct file_operations asl_fops = {
+static const struct file_operations asl_fops = {
.open = asl_open,
.read = seq_read,
.llseek = seq_lseek,
.owner = THIS_MODULE,
};
-static struct file_operations pzl_fops = {
+static const struct file_operations pzl_fops = {
.open = pzl_open,
.read = seq_read,
.llseek = seq_lseek,
return read_count;
}
-static struct
-file_operations usb_rio_fops = {
+static const struct file_operations usb_rio_fops = {
.owner = THIS_MODULE,
.read = read_rio,
.write = write_rio,
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
-#include <linux/kref.h>
#include "sisusb.h"
return 0;
}
-static struct vm_operations_struct mon_bin_vm_ops = {
+static const struct vm_operations_struct mon_bin_vm_ops = {
.open = mon_bin_vma_open,
.close = mon_bin_vma_close,
.fault = mon_bin_vma_fault,
}
}
+#ifdef CONFIG_PM
static void stop_read_write_urbs(struct usb_serial *serial)
{
int i, j;
return ec ? -EIO : 0;
}
+#else
+#define sierra_suspend NULL
+#define sierra_resume NULL
+#endif
static struct usb_serial_driver sierra_device = {
.driver = {
* This is the first place a new tty gets used. Hence this is where we
* acquire references to the usb_serial structure and the driver module,
* where we store a pointer to the port, and where we do an autoresume.
- * All these actions are reversed in serial_release().
+ * All these actions are reversed in serial_cleanup().
*/
static int serial_install(struct tty_driver *driver, struct tty_struct *tty)
{
}
/**
- * serial_release - free resources post close/hangup
+ * serial_cleanup - free resources post close/hangup
* @port: port to free up
*
* Do the resource freeing and refcount dropping for the port.
* Avoid freeing the console.
*
- * Called when the last tty kref is dropped.
+ * Called asynchronously after the last tty kref is dropped,
+ * and the tty layer has already done the tty_shutdown(tty);
*/
-static void serial_release(struct tty_struct *tty)
+static void serial_cleanup(struct tty_struct *tty)
{
struct usb_serial_port *port = tty->driver_data;
struct usb_serial *serial;
dbg("%s - port %d", __func__, port->number);
- /* Standard shutdown processing */
- tty_shutdown(tty);
-
tty->driver_data = NULL;
serial = port->serial;
.chars_in_buffer = serial_chars_in_buffer,
.tiocmget = serial_tiocmget,
.tiocmset = serial_tiocmset,
- .shutdown = serial_release,
+ .cleanup = serial_cleanup,
.install = serial_install,
.proc_fops = &serial_proc_fops,
};
return ret < 0 ? ret : len;
}
-static struct file_operations command_fops = {
+static const struct file_operations command_fops = {
.open = command_open,
.write = command_write,
.read = NULL,
return single_open(file, reservations_print, inode->i_private);
}
-static struct file_operations reservations_fops = {
+static const struct file_operations reservations_fops = {
.open = reservations_open,
.read = seq_read,
.llseek = seq_lseek,
return single_open(file, drp_avail_print, inode->i_private);
}
-static struct file_operations drp_avail_fops = {
+static const struct file_operations drp_avail_fops = {
.open = drp_avail_open,
.read = seq_read,
.llseek = seq_lseek,
Say y here to support the LCD panels usually found on SHARP
corgi (C7x0) and spitz (Cxx00) models.
+config LCD_LMS283GF05
+ tristate "Samsung LMS283GF05 LCD"
+ depends on LCD_CLASS_DEVICE && SPI_MASTER && GENERIC_GPIO
+ help
+ SPI driver for Samsung LMS283GF05. This provides basic support
+ for powering the LCD up/down through a sysfs interface.
+
config LCD_LTV350QV
tristate "Samsung LTV350QV LCD Panel"
depends on LCD_CLASS_DEVICE && SPI_MASTER
help
If you have a Tabletkiosk Sahara Touch-iT, say y to enable the
backlight driver.
+
+config BACKLIGHT_WM831X
+ tristate "WM831x PMIC Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && MFD_WM831X
+ help
+ If you have a backlight driven by the ISINK and DCDC of a
+ WM831x PMIC say y to enable the backlight driver for it.
+
+config BACKLIGHT_ADX
+ tristate "Avionic Design Xanthos Backlight Driver"
+ depends on BACKLIGHT_CLASS_DEVICE && ARCH_PXA_ADX
+ default y
+ help
+ Say Y to enable the backlight driver on Avionic Design Xanthos-based
+ boards.
+
+config BACKLIGHT_ADP5520
+ tristate "Backlight Driver for ADP5520/ADP5501 using WLED"
+ depends on BACKLIGHT_CLASS_DEVICE && PMIC_ADP5520
+ help
+ If you have a LCD backlight connected to the BST/BL_SNK output of
+ ADP5520 or ADP5501, say Y here to enable this driver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called adp5520_bl.
+
obj-$(CONFIG_LCD_CLASS_DEVICE) += lcd.o
obj-$(CONFIG_LCD_CORGI) += corgi_lcd.o
obj-$(CONFIG_LCD_HP700) += jornada720_lcd.o
+obj-$(CONFIG_LCD_LMS283GF05) += lms283gf05.o
obj-$(CONFIG_LCD_LTV350QV) += ltv350qv.o
obj-$(CONFIG_LCD_ILI9320) += ili9320.o
obj-$(CONFIG_LCD_PLATFORM) += platform_lcd.o
obj-$(CONFIG_BACKLIGHT_MBP_NVIDIA) += mbp_nvidia_bl.o
obj-$(CONFIG_BACKLIGHT_TOSA) += tosa_bl.o
obj-$(CONFIG_BACKLIGHT_SAHARA) += kb3886_bl.o
+obj-$(CONFIG_BACKLIGHT_WM831X) += wm831x_bl.o
+obj-$(CONFIG_BACKLIGHT_ADX) += adx_bl.o
+obj-$(CONFIG_BACKLIGHT_ADP5520) += adp5520_bl.o
--- /dev/null
+/*
+ * Backlight driver for Analog Devices ADP5520/ADP5501 MFD PMICs
+ *
+ * Copyright 2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/fb.h>
+#include <linux/backlight.h>
+#include <linux/mfd/adp5520.h>
+
+struct adp5520_bl {
+ struct device *master;
+ struct adp5520_backlight_platfrom_data *pdata;
+ struct mutex lock;
+ unsigned long cached_daylight_max;
+ int id;
+ int current_brightness;
+};
+
+static int adp5520_bl_set(struct backlight_device *bl, int brightness)
+{
+ struct adp5520_bl *data = bl_get_data(bl);
+ struct device *master = data->master;
+ int ret = 0;
+
+ if (data->pdata->en_ambl_sens) {
+ if ((brightness > 0) && (brightness < ADP5020_MAX_BRIGHTNESS)) {
+ /* Disable Ambient Light auto adjust */
+ ret |= adp5520_clr_bits(master, BL_CONTROL,
+ BL_AUTO_ADJ);
+ ret |= adp5520_write(master, DAYLIGHT_MAX, brightness);
+ } else {
+ /*
+ * MAX_BRIGHTNESS -> Enable Ambient Light auto adjust
+ * restore daylight l3 sysfs brightness
+ */
+ ret |= adp5520_write(master, DAYLIGHT_MAX,
+ data->cached_daylight_max);
+ ret |= adp5520_set_bits(master, BL_CONTROL,
+ BL_AUTO_ADJ);
+ }
+ } else {
+ ret |= adp5520_write(master, DAYLIGHT_MAX, brightness);
+ }
+
+ if (data->current_brightness && brightness == 0)
+ ret |= adp5520_set_bits(master,
+ MODE_STATUS, DIM_EN);
+ else if (data->current_brightness == 0 && brightness)
+ ret |= adp5520_clr_bits(master,
+ MODE_STATUS, DIM_EN);
+
+ if (!ret)
+ data->current_brightness = brightness;
+
+ return ret;
+}
+
+static int adp5520_bl_update_status(struct backlight_device *bl)
+{
+ int brightness = bl->props.brightness;
+ if (bl->props.power != FB_BLANK_UNBLANK)
+ brightness = 0;
+
+ if (bl->props.fb_blank != FB_BLANK_UNBLANK)
+ brightness = 0;
+
+ return adp5520_bl_set(bl, brightness);
+}
+
+static int adp5520_bl_get_brightness(struct backlight_device *bl)
+{
+ struct adp5520_bl *data = bl_get_data(bl);
+ int error;
+ uint8_t reg_val;
+
+ error = adp5520_read(data->master, BL_VALUE, ®_val);
+
+ return error ? data->current_brightness : reg_val;
+}
+
+static struct backlight_ops adp5520_bl_ops = {
+ .update_status = adp5520_bl_update_status,
+ .get_brightness = adp5520_bl_get_brightness,
+};
+
+static int adp5520_bl_setup(struct backlight_device *bl)
+{
+ struct adp5520_bl *data = bl_get_data(bl);
+ struct device *master = data->master;
+ struct adp5520_backlight_platfrom_data *pdata = data->pdata;
+ int ret = 0;
+
+ ret |= adp5520_write(master, DAYLIGHT_MAX, pdata->l1_daylight_max);
+ ret |= adp5520_write(master, DAYLIGHT_DIM, pdata->l1_daylight_dim);
+
+ if (pdata->en_ambl_sens) {
+ data->cached_daylight_max = pdata->l1_daylight_max;
+ ret |= adp5520_write(master, OFFICE_MAX, pdata->l2_office_max);
+ ret |= adp5520_write(master, OFFICE_DIM, pdata->l2_office_dim);
+ ret |= adp5520_write(master, DARK_MAX, pdata->l3_dark_max);
+ ret |= adp5520_write(master, DARK_DIM, pdata->l3_dark_dim);
+ ret |= adp5520_write(master, L2_TRIP, pdata->l2_trip);
+ ret |= adp5520_write(master, L2_HYS, pdata->l2_hyst);
+ ret |= adp5520_write(master, L3_TRIP, pdata->l3_trip);
+ ret |= adp5520_write(master, L3_HYS, pdata->l3_hyst);
+ ret |= adp5520_write(master, ALS_CMPR_CFG,
+ ALS_CMPR_CFG_VAL(pdata->abml_filt, L3_EN));
+ }
+
+ ret |= adp5520_write(master, BL_CONTROL,
+ BL_CTRL_VAL(pdata->fade_led_law, pdata->en_ambl_sens));
+
+ ret |= adp5520_write(master, BL_FADE, FADE_VAL(pdata->fade_in,
+ pdata->fade_out));
+
+ ret |= adp5520_set_bits(master, MODE_STATUS, BL_EN | DIM_EN);
+
+ return ret;
+}
+
+static ssize_t adp5520_show(struct device *dev, char *buf, int reg)
+{
+ struct adp5520_bl *data = dev_get_drvdata(dev);
+ int error;
+ uint8_t reg_val;
+
+ mutex_lock(&data->lock);
+ error = adp5520_read(data->master, reg, ®_val);
+ mutex_unlock(&data->lock);
+
+ return sprintf(buf, "%u\n", reg_val);
+}
+
+static ssize_t adp5520_store(struct device *dev, const char *buf,
+ size_t count, int reg)
+{
+ struct adp5520_bl *data = dev_get_drvdata(dev);
+ unsigned long val;
+ int ret;
+
+ ret = strict_strtoul(buf, 10, &val);
+ if (ret)
+ return ret;
+
+ mutex_lock(&data->lock);
+ adp5520_write(data->master, reg, val);
+ mutex_unlock(&data->lock);
+
+ return count;
+}
+
+static ssize_t adp5520_bl_dark_max_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return adp5520_show(dev, buf, DARK_MAX);
+}
+
+static ssize_t adp5520_bl_dark_max_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ return adp5520_store(dev, buf, count, DARK_MAX);
+}
+static DEVICE_ATTR(dark_max, 0664, adp5520_bl_dark_max_show,
+ adp5520_bl_dark_max_store);
+
+static ssize_t adp5520_bl_office_max_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return adp5520_show(dev, buf, OFFICE_MAX);
+}
+
+static ssize_t adp5520_bl_office_max_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ return adp5520_store(dev, buf, count, OFFICE_MAX);
+}
+static DEVICE_ATTR(office_max, 0664, adp5520_bl_office_max_show,
+ adp5520_bl_office_max_store);
+
+static ssize_t adp5520_bl_daylight_max_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return adp5520_show(dev, buf, DAYLIGHT_MAX);
+}
+
+static ssize_t adp5520_bl_daylight_max_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct adp5520_bl *data = dev_get_drvdata(dev);
+
+ strict_strtoul(buf, 10, &data->cached_daylight_max);
+ return adp5520_store(dev, buf, count, DAYLIGHT_MAX);
+}
+static DEVICE_ATTR(daylight_max, 0664, adp5520_bl_daylight_max_show,
+ adp5520_bl_daylight_max_store);
+
+static ssize_t adp5520_bl_dark_dim_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return adp5520_show(dev, buf, DARK_DIM);
+}
+
+static ssize_t adp5520_bl_dark_dim_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ return adp5520_store(dev, buf, count, DARK_DIM);
+}
+static DEVICE_ATTR(dark_dim, 0664, adp5520_bl_dark_dim_show,
+ adp5520_bl_dark_dim_store);
+
+static ssize_t adp5520_bl_office_dim_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return adp5520_show(dev, buf, OFFICE_DIM);
+}
+
+static ssize_t adp5520_bl_office_dim_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ return adp5520_store(dev, buf, count, OFFICE_DIM);
+}
+static DEVICE_ATTR(office_dim, 0664, adp5520_bl_office_dim_show,
+ adp5520_bl_office_dim_store);
+
+static ssize_t adp5520_bl_daylight_dim_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ return adp5520_show(dev, buf, DAYLIGHT_DIM);
+}
+
+static ssize_t adp5520_bl_daylight_dim_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ return adp5520_store(dev, buf, count, DAYLIGHT_DIM);
+}
+static DEVICE_ATTR(daylight_dim, 0664, adp5520_bl_daylight_dim_show,
+ adp5520_bl_daylight_dim_store);
+
+static struct attribute *adp5520_bl_attributes[] = {
+ &dev_attr_dark_max.attr,
+ &dev_attr_dark_dim.attr,
+ &dev_attr_office_max.attr,
+ &dev_attr_office_dim.attr,
+ &dev_attr_daylight_max.attr,
+ &dev_attr_daylight_dim.attr,
+ NULL
+};
+
+static const struct attribute_group adp5520_bl_attr_group = {
+ .attrs = adp5520_bl_attributes,
+};
+
+static int __devinit adp5520_bl_probe(struct platform_device *pdev)
+{
+ struct backlight_device *bl;
+ struct adp5520_bl *data;
+ int ret = 0;
+
+ data = kzalloc(sizeof(*data), GFP_KERNEL);
+ if (data == NULL)
+ return -ENOMEM;
+
+ data->master = pdev->dev.parent;
+ data->pdata = pdev->dev.platform_data;
+
+ if (data->pdata == NULL) {
+ dev_err(&pdev->dev, "missing platform data\n");
+ kfree(data);
+ return -ENODEV;
+ }
+
+ data->id = pdev->id;
+ data->current_brightness = 0;
+
+ mutex_init(&data->lock);
+
+ bl = backlight_device_register(pdev->name, data->master,
+ data, &adp5520_bl_ops);
+ if (IS_ERR(bl)) {
+ dev_err(&pdev->dev, "failed to register backlight\n");
+ kfree(data);
+ return PTR_ERR(bl);
+ }
+
+ bl->props.max_brightness =
+ bl->props.brightness = ADP5020_MAX_BRIGHTNESS;
+
+ if (data->pdata->en_ambl_sens)
+ ret = sysfs_create_group(&bl->dev.kobj,
+ &adp5520_bl_attr_group);
+
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register sysfs\n");
+ backlight_device_unregister(bl);
+ kfree(data);
+ }
+
+ platform_set_drvdata(pdev, bl);
+ ret |= adp5520_bl_setup(bl);
+ backlight_update_status(bl);
+
+ return ret;
+}
+
+static int __devexit adp5520_bl_remove(struct platform_device *pdev)
+{
+ struct backlight_device *bl = platform_get_drvdata(pdev);
+ struct adp5520_bl *data = bl_get_data(bl);
+
+ adp5520_clr_bits(data->master, MODE_STATUS, BL_EN);
+
+ if (data->pdata->en_ambl_sens)
+ sysfs_remove_group(&bl->dev.kobj,
+ &adp5520_bl_attr_group);
+
+ backlight_device_unregister(bl);
+ kfree(data);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int adp5520_bl_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ struct backlight_device *bl = platform_get_drvdata(pdev);
+ return adp5520_bl_set(bl, 0);
+}
+
+static int adp5520_bl_resume(struct platform_device *pdev)
+{
+ struct backlight_device *bl = platform_get_drvdata(pdev);
+
+ backlight_update_status(bl);
+ return 0;
+}
+#else
+#define adp5520_bl_suspend NULL
+#define adp5520_bl_resume NULL
+#endif
+
+static struct platform_driver adp5520_bl_driver = {
+ .driver = {
+ .name = "adp5520-backlight",
+ .owner = THIS_MODULE,
+ },
+ .probe = adp5520_bl_probe,
+ .remove = __devexit_p(adp5520_bl_remove),
+ .suspend = adp5520_bl_suspend,
+ .resume = adp5520_bl_resume,
+};
+
+static int __init adp5520_bl_init(void)
+{
+ return platform_driver_register(&adp5520_bl_driver);
+}
+module_init(adp5520_bl_init);
+
+static void __exit adp5520_bl_exit(void)
+{
+ platform_driver_unregister(&adp5520_bl_driver);
+}
+module_exit(adp5520_bl_exit);
+
+MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
+MODULE_DESCRIPTION("ADP5520(01) Backlight Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:adp5520-backlight");
--- /dev/null
+/*
+ * linux/drivers/video/backlight/adx.c
+ *
+ * Copyright (C) 2009 Avionic Design GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Written by Thierry Reding <thierry.reding@avionic-design.de>
+ */
+
+#include <linux/backlight.h>
+#include <linux/fb.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+/* register definitions */
+#define ADX_BACKLIGHT_CONTROL 0x00
+#define ADX_BACKLIGHT_CONTROL_ENABLE (1 << 0)
+#define ADX_BACKLIGHT_BRIGHTNESS 0x08
+#define ADX_BACKLIGHT_STATUS 0x10
+#define ADX_BACKLIGHT_ERROR 0x18
+
+struct adxbl {
+ void __iomem *base;
+};
+
+static int adx_backlight_update_status(struct backlight_device *bldev)
+{
+ struct adxbl *bl = bl_get_data(bldev);
+ u32 value;
+
+ value = bldev->props.brightness;
+ writel(value, bl->base + ADX_BACKLIGHT_BRIGHTNESS);
+
+ value = readl(bl->base + ADX_BACKLIGHT_CONTROL);
+
+ if (bldev->props.state & BL_CORE_FBBLANK)
+ value &= ~ADX_BACKLIGHT_CONTROL_ENABLE;
+ else
+ value |= ADX_BACKLIGHT_CONTROL_ENABLE;
+
+ writel(value, bl->base + ADX_BACKLIGHT_CONTROL);
+
+ return 0;
+}
+
+static int adx_backlight_get_brightness(struct backlight_device *bldev)
+{
+ struct adxbl *bl = bl_get_data(bldev);
+ u32 brightness;
+
+ brightness = readl(bl->base + ADX_BACKLIGHT_BRIGHTNESS);
+ return brightness & 0xff;
+}
+
+static int adx_backlight_check_fb(struct fb_info *fb)
+{
+ return 1;
+}
+
+static struct backlight_ops adx_backlight_ops = {
+ .options = 0,
+ .update_status = adx_backlight_update_status,
+ .get_brightness = adx_backlight_get_brightness,
+ .check_fb = adx_backlight_check_fb,
+};
+
+static int __devinit adx_backlight_probe(struct platform_device *pdev)
+{
+ struct backlight_device *bldev;
+ struct resource *res;
+ struct adxbl *bl;
+ int ret = 0;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ ret = -ENXIO;
+ goto out;
+ }
+
+ res = devm_request_mem_region(&pdev->dev, res->start,
+ resource_size(res), res->name);
+ if (!res) {
+ ret = -ENXIO;
+ goto out;
+ }
+
+ bl = devm_kzalloc(&pdev->dev, sizeof(*bl), GFP_KERNEL);
+ if (!bl) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ bl->base = devm_ioremap_nocache(&pdev->dev, res->start,
+ resource_size(res));
+ if (!bl->base) {
+ ret = -ENXIO;
+ goto out;
+ }
+
+ bldev = backlight_device_register(dev_name(&pdev->dev), &pdev->dev, bl,
+ &adx_backlight_ops);
+ if (!bldev) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ bldev->props.max_brightness = 0xff;
+ bldev->props.brightness = 0xff;
+ bldev->props.power = FB_BLANK_UNBLANK;
+
+ platform_set_drvdata(pdev, bldev);
+
+out:
+ return ret;
+}
+
+static int __devexit adx_backlight_remove(struct platform_device *pdev)
+{
+ struct backlight_device *bldev;
+ int ret = 0;
+
+ bldev = platform_get_drvdata(pdev);
+ bldev->props.power = FB_BLANK_UNBLANK;
+ bldev->props.brightness = 0xff;
+ backlight_update_status(bldev);
+ backlight_device_unregister(bldev);
+ platform_set_drvdata(pdev, NULL);
+
+ return ret;
+}
+
+#ifdef CONFIG_PM
+static int adx_backlight_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ return 0;
+}
+
+static int adx_backlight_resume(struct platform_device *pdev)
+{
+ return 0;
+}
+#else
+#define adx_backlight_suspend NULL
+#define adx_backlight_resume NULL
+#endif
+
+static struct platform_driver adx_backlight_driver = {
+ .probe = adx_backlight_probe,
+ .remove = __devexit_p(adx_backlight_remove),
+ .suspend = adx_backlight_suspend,
+ .resume = adx_backlight_resume,
+ .driver = {
+ .name = "adx-backlight",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init adx_backlight_init(void)
+{
+ return platform_driver_register(&adx_backlight_driver);
+}
+
+static void __exit adx_backlight_exit(void)
+{
+ platform_driver_unregister(&adx_backlight_driver);
+}
+
+module_init(adx_backlight_init);
+module_exit(adx_backlight_exit);
+
+MODULE_AUTHOR("Thierry Reding <thierry.reding@avionic-design.de>");
+MODULE_DESCRIPTION("Avionic Design Xanthos Backlight Driver");
+MODULE_LICENSE("GPL v2");
}
#endif /* CONFIG_FB */
+static void backlight_generate_event(struct backlight_device *bd,
+ enum backlight_update_reason reason)
+{
+ char *envp[2];
+
+ switch (reason) {
+ case BACKLIGHT_UPDATE_SYSFS:
+ envp[0] = "SOURCE=sysfs";
+ break;
+ case BACKLIGHT_UPDATE_HOTKEY:
+ envp[0] = "SOURCE=hotkey";
+ break;
+ default:
+ envp[0] = "SOURCE=unknown";
+ break;
+ }
+ envp[1] = NULL;
+ kobject_uevent_env(&bd->dev.kobj, KOBJ_CHANGE, envp);
+ sysfs_notify(&bd->dev.kobj, NULL, "actual_brightness");
+}
+
static ssize_t backlight_show_power(struct device *dev,
struct device_attribute *attr,char *buf)
{
}
mutex_unlock(&bd->ops_lock);
+ backlight_generate_event(bd, BACKLIGHT_UPDATE_SYSFS);
+
return rc;
}
__ATTR_NULL,
};
+/**
+ * backlight_force_update - tell the backlight subsystem that hardware state
+ * has changed
+ * @bd: the backlight device to update
+ *
+ * Updates the internal state of the backlight in response to a hardware event,
+ * and generate a uevent to notify userspace
+ */
+void backlight_force_update(struct backlight_device *bd,
+ enum backlight_update_reason reason)
+{
+ mutex_lock(&bd->ops_lock);
+ if (bd->ops && bd->ops->get_brightness)
+ bd->props.brightness = bd->ops->get_brightness(bd);
+ mutex_unlock(&bd->ops_lock);
+ backlight_generate_event(bd, reason);
+}
+EXPORT_SYMBOL(backlight_force_update);
+
/**
* backlight_device_register - create and register a new object of
* backlight_device class.
}
#ifdef CONFIG_PM
-static int da903x_backlight_suspend(struct platform_device *pdev,
- pm_message_t state)
+static int da903x_backlight_suspend(struct device *dev)
{
+ struct platform_device *pdev = to_platform_device(dev);
struct backlight_device *bl = platform_get_drvdata(pdev);
return da903x_backlight_set(bl, 0);
}
-static int da903x_backlight_resume(struct platform_device *pdev)
+static int da903x_backlight_resume(struct device *dev)
{
+ struct platform_device *pdev = to_platform_device(dev);
struct backlight_device *bl = platform_get_drvdata(pdev);
backlight_update_status(bl);
return 0;
}
-#else
-#define da903x_backlight_suspend NULL
-#define da903x_backlight_resume NULL
+
+static struct dev_pm_ops da903x_backlight_pm_ops = {
+ .suspend = da903x_backlight_suspend,
+ .resume = da903x_backlight_resume,
+};
#endif
static struct platform_driver da903x_backlight_driver = {
.driver = {
.name = "da903x-backlight",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &da903x_backlight_pm_ops,
+#endif
},
.probe = da903x_backlight_probe,
.remove = da903x_backlight_remove,
- .suspend = da903x_backlight_suspend,
- .resume = da903x_backlight_resume,
};
static int __init da903x_backlight_init(void)
.update_status = hp680bl_set_intensity,
};
-static int __init hp680bl_probe(struct platform_device *pdev)
+static int __devinit hp680bl_probe(struct platform_device *pdev)
{
struct backlight_device *bd;
--- /dev/null
+/*
+ * lms283gf05.c -- support for Samsung LMS283GF05 LCD
+ *
+ * Copyright (c) 2009 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/lcd.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/lms283gf05.h>
+
+struct lms283gf05_state {
+ struct spi_device *spi;
+ struct lcd_device *ld;
+};
+
+struct lms283gf05_seq {
+ unsigned char reg;
+ unsigned short value;
+ unsigned char delay;
+};
+
+/* Magic sequences supplied by manufacturer, for details refer to datasheet */
+static struct lms283gf05_seq disp_initseq[] = {
+ /* REG, VALUE, DELAY */
+ { 0x07, 0x0000, 0 },
+ { 0x13, 0x0000, 10 },
+
+ { 0x11, 0x3004, 0 },
+ { 0x14, 0x200F, 0 },
+ { 0x10, 0x1a20, 0 },
+ { 0x13, 0x0040, 50 },
+
+ { 0x13, 0x0060, 0 },
+ { 0x13, 0x0070, 200 },
+
+ { 0x01, 0x0127, 0 },
+ { 0x02, 0x0700, 0 },
+ { 0x03, 0x1030, 0 },
+ { 0x08, 0x0208, 0 },
+ { 0x0B, 0x0620, 0 },
+ { 0x0C, 0x0110, 0 },
+ { 0x30, 0x0120, 0 },
+ { 0x31, 0x0127, 0 },
+ { 0x32, 0x0000, 0 },
+ { 0x33, 0x0503, 0 },
+ { 0x34, 0x0727, 0 },
+ { 0x35, 0x0124, 0 },
+ { 0x36, 0x0706, 0 },
+ { 0x37, 0x0701, 0 },
+ { 0x38, 0x0F00, 0 },
+ { 0x39, 0x0F00, 0 },
+ { 0x40, 0x0000, 0 },
+ { 0x41, 0x0000, 0 },
+ { 0x42, 0x013f, 0 },
+ { 0x43, 0x0000, 0 },
+ { 0x44, 0x013f, 0 },
+ { 0x45, 0x0000, 0 },
+ { 0x46, 0xef00, 0 },
+ { 0x47, 0x013f, 0 },
+ { 0x48, 0x0000, 0 },
+ { 0x07, 0x0015, 30 },
+
+ { 0x07, 0x0017, 0 },
+
+ { 0x20, 0x0000, 0 },
+ { 0x21, 0x0000, 0 },
+ { 0x22, 0x0000, 0 }
+};
+
+static struct lms283gf05_seq disp_pdwnseq[] = {
+ { 0x07, 0x0016, 30 },
+
+ { 0x07, 0x0004, 0 },
+ { 0x10, 0x0220, 20 },
+
+ { 0x13, 0x0060, 50 },
+
+ { 0x13, 0x0040, 50 },
+
+ { 0x13, 0x0000, 0 },
+ { 0x10, 0x0000, 0 }
+};
+
+
+static void lms283gf05_reset(unsigned long gpio, bool inverted)
+{
+ gpio_set_value(gpio, !inverted);
+ mdelay(100);
+ gpio_set_value(gpio, inverted);
+ mdelay(20);
+ gpio_set_value(gpio, !inverted);
+ mdelay(20);
+}
+
+static void lms283gf05_toggle(struct spi_device *spi,
+ struct lms283gf05_seq *seq, int sz)
+{
+ char buf[3];
+ int i;
+
+ for (i = 0; i < sz; i++) {
+ buf[0] = 0x74;
+ buf[1] = 0x00;
+ buf[2] = seq[i].reg;
+ spi_write(spi, buf, 3);
+
+ buf[0] = 0x76;
+ buf[1] = seq[i].value >> 8;
+ buf[2] = seq[i].value & 0xff;
+ spi_write(spi, buf, 3);
+
+ mdelay(seq[i].delay);
+ }
+}
+
+static int lms283gf05_power_set(struct lcd_device *ld, int power)
+{
+ struct lms283gf05_state *st = lcd_get_data(ld);
+ struct spi_device *spi = st->spi;
+ struct lms283gf05_pdata *pdata = spi->dev.platform_data;
+
+ if (power) {
+ if (pdata)
+ lms283gf05_reset(pdata->reset_gpio,
+ pdata->reset_inverted);
+ lms283gf05_toggle(spi, disp_initseq, ARRAY_SIZE(disp_initseq));
+ } else {
+ lms283gf05_toggle(spi, disp_pdwnseq, ARRAY_SIZE(disp_pdwnseq));
+ if (pdata)
+ gpio_set_value(pdata->reset_gpio,
+ pdata->reset_inverted);
+ }
+
+ return 0;
+}
+
+static struct lcd_ops lms_ops = {
+ .set_power = lms283gf05_power_set,
+ .get_power = NULL,
+};
+
+static int __devinit lms283gf05_probe(struct spi_device *spi)
+{
+ struct lms283gf05_state *st;
+ struct lms283gf05_pdata *pdata = spi->dev.platform_data;
+ struct lcd_device *ld;
+ int ret = 0;
+
+ if (pdata != NULL) {
+ ret = gpio_request(pdata->reset_gpio, "LMS285GF05 RESET");
+ if (ret)
+ return ret;
+
+ ret = gpio_direction_output(pdata->reset_gpio,
+ !pdata->reset_inverted);
+ if (ret)
+ goto err;
+ }
+
+ st = kzalloc(sizeof(struct lms283gf05_state), GFP_KERNEL);
+ if (st == NULL) {
+ dev_err(&spi->dev, "No memory for device state\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ ld = lcd_device_register("lms283gf05", &spi->dev, st, &lms_ops);
+ if (IS_ERR(ld)) {
+ ret = PTR_ERR(ld);
+ goto err2;
+ }
+
+ st->spi = spi;
+ st->ld = ld;
+
+ dev_set_drvdata(&spi->dev, st);
+
+ /* kick in the LCD */
+ if (pdata)
+ lms283gf05_reset(pdata->reset_gpio, pdata->reset_inverted);
+ lms283gf05_toggle(spi, disp_initseq, ARRAY_SIZE(disp_initseq));
+
+ return 0;
+
+err2:
+ kfree(st);
+err:
+ if (pdata != NULL)
+ gpio_free(pdata->reset_gpio);
+
+ return ret;
+}
+
+static int __devexit lms283gf05_remove(struct spi_device *spi)
+{
+ struct lms283gf05_state *st = dev_get_drvdata(&spi->dev);
+ struct lms283gf05_pdata *pdata = st->spi->dev.platform_data;
+
+ lcd_device_unregister(st->ld);
+
+ if (pdata != NULL)
+ gpio_free(pdata->reset_gpio);
+
+ kfree(st);
+
+ return 0;
+}
+
+static struct spi_driver lms283gf05_driver = {
+ .driver = {
+ .name = "lms283gf05",
+ .owner = THIS_MODULE,
+ },
+ .probe = lms283gf05_probe,
+ .remove = __devexit_p(lms283gf05_remove),
+};
+
+static __init int lms283gf05_init(void)
+{
+ return spi_register_driver(&lms283gf05_driver);
+}
+
+static __exit void lms283gf05_exit(void)
+{
+ spi_unregister_driver(&lms283gf05_driver);
+}
+
+module_init(lms283gf05_init);
+module_exit(lms283gf05_exit);
+
+MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("LCD283GF05 LCD");
+MODULE_LICENSE("GPL v2");
},
.driver_data = (void *)&intel_chipset_data,
},
+ {
+ .callback = mbp_dmi_match,
+ .ident = "MacBookAir 1,1",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "MacBookAir1,1"),
+ },
+ .driver_data = (void *)&intel_chipset_data,
+ },
{
.callback = mbp_dmi_match,
.ident = "MacBook 5,1",
},
.driver_data = (void *)&nvidia_chipset_data,
},
+ {
+ .callback = mbp_dmi_match,
+ .ident = "MacBook 5,2",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "MacBook5,2"),
+ },
+ .driver_data = (void *)&nvidia_chipset_data,
+ },
{
.callback = mbp_dmi_match,
.ident = "MacBookAir 2,1",
},
.driver_data = (void *)&nvidia_chipset_data,
},
+ {
+ .callback = mbp_dmi_match,
+ .ident = "MacBookPro 5,2",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5,2"),
+ },
+ .driver_data = (void *)&nvidia_chipset_data,
+ },
+ {
+ .callback = mbp_dmi_match,
+ .ident = "MacBookPro 5,5",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Apple Inc."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "MacBookPro5,5"),
+ },
+ .driver_data = (void *)&nvidia_chipset_data,
+ },
{ }
};
--- /dev/null
+/*
+ * Backlight driver for Wolfson Microelectronics WM831x PMICs
+ *
+ * Copyright 2009 Wolfson Microelectonics plc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/fb.h>
+#include <linux/backlight.h>
+
+#include <linux/mfd/wm831x/core.h>
+#include <linux/mfd/wm831x/pdata.h>
+#include <linux/mfd/wm831x/regulator.h>
+
+struct wm831x_backlight_data {
+ struct wm831x *wm831x;
+ int isink_reg;
+ int current_brightness;
+};
+
+static int wm831x_backlight_set(struct backlight_device *bl, int brightness)
+{
+ struct wm831x_backlight_data *data = bl_get_data(bl);
+ struct wm831x *wm831x = data->wm831x;
+ int power_up = !data->current_brightness && brightness;
+ int power_down = data->current_brightness && !brightness;
+ int ret;
+
+ if (power_up) {
+ /* Enable the ISINK */
+ ret = wm831x_set_bits(wm831x, data->isink_reg,
+ WM831X_CS1_ENA, WM831X_CS1_ENA);
+ if (ret < 0)
+ goto err;
+
+ /* Enable the DC-DC */
+ ret = wm831x_set_bits(wm831x, WM831X_DCDC_ENABLE,
+ WM831X_DC4_ENA, WM831X_DC4_ENA);
+ if (ret < 0)
+ goto err;
+ }
+
+ if (power_down) {
+ /* DCDC first */
+ ret = wm831x_set_bits(wm831x, WM831X_DCDC_ENABLE,
+ WM831X_DC4_ENA, 0);
+ if (ret < 0)
+ goto err;
+
+ /* ISINK */
+ ret = wm831x_set_bits(wm831x, data->isink_reg,
+ WM831X_CS1_DRIVE | WM831X_CS1_ENA, 0);
+ if (ret < 0)
+ goto err;
+ }
+
+ /* Set the new brightness */
+ ret = wm831x_set_bits(wm831x, data->isink_reg,
+ WM831X_CS1_ISEL_MASK, brightness);
+ if (ret < 0)
+ goto err;
+
+ if (power_up) {
+ /* Drive current through the ISINK */
+ ret = wm831x_set_bits(wm831x, data->isink_reg,
+ WM831X_CS1_DRIVE, WM831X_CS1_DRIVE);
+ if (ret < 0)
+ return ret;
+ }
+
+ data->current_brightness = brightness;
+
+ return 0;
+
+err:
+ /* If we were in the middle of a power transition always shut down
+ * for safety.
+ */
+ if (power_up || power_down) {
+ wm831x_set_bits(wm831x, WM831X_DCDC_ENABLE, WM831X_DC4_ENA, 0);
+ wm831x_set_bits(wm831x, data->isink_reg, WM831X_CS1_ENA, 0);
+ }
+
+ return ret;
+}
+
+static int wm831x_backlight_update_status(struct backlight_device *bl)
+{
+ int brightness = bl->props.brightness;
+
+ if (bl->props.power != FB_BLANK_UNBLANK)
+ brightness = 0;
+
+ if (bl->props.fb_blank != FB_BLANK_UNBLANK)
+ brightness = 0;
+
+ if (bl->props.state & BL_CORE_SUSPENDED)
+ brightness = 0;
+
+ return wm831x_backlight_set(bl, brightness);
+}
+
+static int wm831x_backlight_get_brightness(struct backlight_device *bl)
+{
+ struct wm831x_backlight_data *data = bl_get_data(bl);
+ return data->current_brightness;
+}
+
+static struct backlight_ops wm831x_backlight_ops = {
+ .options = BL_CORE_SUSPENDRESUME,
+ .update_status = wm831x_backlight_update_status,
+ .get_brightness = wm831x_backlight_get_brightness,
+};
+
+static int wm831x_backlight_probe(struct platform_device *pdev)
+{
+ struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent);
+ struct wm831x_pdata *wm831x_pdata;
+ struct wm831x_backlight_pdata *pdata;
+ struct wm831x_backlight_data *data;
+ struct backlight_device *bl;
+ int ret, i, max_isel, isink_reg, dcdc_cfg;
+
+ /* We need platform data */
+ if (pdev->dev.parent->platform_data) {
+ wm831x_pdata = pdev->dev.parent->platform_data;
+ pdata = wm831x_pdata->backlight;
+ } else {
+ pdata = NULL;
+ }
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "No platform data supplied\n");
+ return -EINVAL;
+ }
+
+ /* Figure out the maximum current we can use */
+ for (i = 0; i < WM831X_ISINK_MAX_ISEL; i++) {
+ if (wm831x_isinkv_values[i] > pdata->max_uA)
+ break;
+ }
+
+ if (i == 0) {
+ dev_err(&pdev->dev, "Invalid max_uA: %duA\n", pdata->max_uA);
+ return -EINVAL;
+ }
+ max_isel = i - 1;
+
+ if (pdata->max_uA != wm831x_isinkv_values[max_isel])
+ dev_warn(&pdev->dev,
+ "Maximum current is %duA not %duA as requested\n",
+ wm831x_isinkv_values[max_isel], pdata->max_uA);
+
+ switch (pdata->isink) {
+ case 1:
+ isink_reg = WM831X_CURRENT_SINK_1;
+ dcdc_cfg = 0;
+ break;
+ case 2:
+ isink_reg = WM831X_CURRENT_SINK_2;
+ dcdc_cfg = WM831X_DC4_FBSRC;
+ break;
+ default:
+ dev_err(&pdev->dev, "Invalid ISINK %d\n", pdata->isink);
+ return -EINVAL;
+ }
+
+ /* Configure the ISINK to use for feedback */
+ ret = wm831x_reg_unlock(wm831x);
+ if (ret < 0)
+ return ret;
+
+ ret = wm831x_set_bits(wm831x, WM831X_DC4_CONTROL, WM831X_DC4_FBSRC,
+ dcdc_cfg);
+
+ wm831x_reg_lock(wm831x);
+ if (ret < 0)
+ return ret;
+
+ data = kzalloc(sizeof(*data), GFP_KERNEL);
+ if (data == NULL)
+ return -ENOMEM;
+
+ data->wm831x = wm831x;
+ data->current_brightness = 0;
+ data->isink_reg = isink_reg;
+
+ bl = backlight_device_register("wm831x", &pdev->dev,
+ data, &wm831x_backlight_ops);
+ if (IS_ERR(bl)) {
+ dev_err(&pdev->dev, "failed to register backlight\n");
+ kfree(data);
+ return PTR_ERR(bl);
+ }
+
+ bl->props.max_brightness = max_isel;
+ bl->props.brightness = max_isel;
+
+ platform_set_drvdata(pdev, bl);
+
+ /* Disable the DCDC if it was started so we can bootstrap */
+ wm831x_set_bits(wm831x, WM831X_DCDC_ENABLE, WM831X_DC4_ENA, 0);
+
+
+ backlight_update_status(bl);
+
+ return 0;
+}
+
+static int wm831x_backlight_remove(struct platform_device *pdev)
+{
+ struct backlight_device *bl = platform_get_drvdata(pdev);
+ struct wm831x_backlight_data *data = bl_get_data(bl);
+
+ backlight_device_unregister(bl);
+ kfree(data);
+ return 0;
+}
+
+static struct platform_driver wm831x_backlight_driver = {
+ .driver = {
+ .name = "wm831x-backlight",
+ .owner = THIS_MODULE,
+ },
+ .probe = wm831x_backlight_probe,
+ .remove = wm831x_backlight_remove,
+};
+
+static int __init wm831x_backlight_init(void)
+{
+ return platform_driver_register(&wm831x_backlight_driver);
+}
+module_init(wm831x_backlight_init);
+
+static void __exit wm831x_backlight_exit(void)
+{
+ platform_driver_unregister(&wm831x_backlight_driver);
+}
+module_exit(wm831x_backlight_exit);
+
+MODULE_DESCRIPTION("Backlight Driver for WM831x PMICs");
+MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:wm831x-backlight");
return 0;
}
-static struct vm_operations_struct fb_deferred_io_vm_ops = {
+static const struct vm_operations_struct fb_deferred_io_vm_ops = {
.fault = fb_deferred_io_fault,
.page_mkwrite = fb_deferred_io_mkwrite,
};
global = 1;
}
- if (!global && !strstr(options, "fb:")) {
+ if (!global && !strchr(options, ':')) {
fb_mode_option = options;
global = 1;
}
atomic_dec(&dispc.map_count[plane]);
}
-static struct vm_operations_struct mmap_user_ops = {
+static const struct vm_operations_struct mmap_user_ops = {
.open = mmap_user_open,
.close = mmap_user_close,
};
* Power management hooks. Note that we won't be called from IRQ context,
* unlike the blank functions above, so we may sleep.
*/
-static int pxafb_suspend(struct platform_device *dev, pm_message_t state)
+static int pxafb_suspend(struct device *dev)
{
- struct pxafb_info *fbi = platform_get_drvdata(dev);
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
set_ctrlr_state(fbi, C_DISABLE_PM);
return 0;
}
-static int pxafb_resume(struct platform_device *dev)
+static int pxafb_resume(struct device *dev)
{
- struct pxafb_info *fbi = platform_get_drvdata(dev);
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
set_ctrlr_state(fbi, C_ENABLE_PM);
return 0;
}
-#else
-#define pxafb_suspend NULL
-#define pxafb_resume NULL
+
+static struct dev_pm_ops pxafb_pm_ops = {
+ .suspend = pxafb_suspend,
+ .resume = pxafb_resume,
+};
#endif
static int __devinit pxafb_init_video_memory(struct pxafb_info *fbi)
goto failed;
}
+ if (cpu_is_pxa3xx() && inf->acceleration_enabled)
+ fbi->fb.fix.accel = FB_ACCEL_PXA3XX;
+
fbi->backlight_power = inf->pxafb_backlight_power;
fbi->lcd_power = inf->pxafb_lcd_power;
goto failed_fbi;
}
- r = request_mem_region(r->start, r->end - r->start + 1, dev->name);
+ r = request_mem_region(r->start, resource_size(r), dev->name);
if (r == NULL) {
dev_err(&dev->dev, "failed to request I/O memory\n");
ret = -EBUSY;
goto failed_fbi;
}
- fbi->mmio_base = ioremap(r->start, r->end - r->start + 1);
+ fbi->mmio_base = ioremap(r->start, resource_size(r));
if (fbi->mmio_base == NULL) {
dev_err(&dev->dev, "failed to map I/O memory\n");
ret = -EBUSY;
failed_free_io:
iounmap(fbi->mmio_base);
failed_free_res:
- release_mem_region(r->start, r->end - r->start + 1);
+ release_mem_region(r->start, resource_size(r));
failed_fbi:
clk_put(fbi->clk);
platform_set_drvdata(dev, NULL);
iounmap(fbi->mmio_base);
r = platform_get_resource(dev, IORESOURCE_MEM, 0);
- release_mem_region(r->start, r->end - r->start + 1);
+ release_mem_region(r->start, resource_size(r));
clk_put(fbi->clk);
kfree(fbi);
static struct platform_driver pxafb_driver = {
.probe = pxafb_probe,
.remove = __devexit_p(pxafb_remove),
- .suspend = pxafb_suspend,
- .resume = pxafb_resume,
.driver = {
.owner = THIS_MODULE,
.name = "pxa2xx-fb",
+#ifdef CONFIG_PM
+ .pm = &pxafb_pm_ops,
+#endif
},
};
* find the kernel part of the task struct, copy the registers and
* the buffer contents and then complete the task.
*/
-static void uvesafb_cn_callback(struct cn_msg *msg)
+static void uvesafb_cn_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
struct uvesafb_task *utask;
struct uvesafb_ktask *task;
+ if (!cap_raised(nsp->eff_cap, CAP_SYS_ADMIN))
+ return;
+
if (msg->seq >= UVESAFB_TASKS_MAX)
return;
dev->mem_start = mem_res->start;
dev->mem_end = mem_res->end;
- len = regs_res->end - regs_res->start;
+ len = resource_size(regs_res);
if (!request_mem_region(regs_res->start, len, dev_name(&dev->dev))) {
printk(KERN_ERR "%s: Can't request vlynq registers\n",
dev_name(&dev->dev));
#include "../w1.h"
#include "../w1_int.h"
-/**
- * Address is selected using 2 pins, resulting in 4 possible addresses.
- * 0x18, 0x19, 0x1a, 0x1b
- * However, the chip cannot be detected without doing an i2c write,
- * so use the force module parameter.
- */
-static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/**
- * Insmod parameters
- */
-I2C_CLIENT_INSMOD_1(ds2482);
-
/**
* The DS2482 registers - there are 3 registers that are addressed by a read
* pointer. The read pointer is set by the last command executed.
static int ds2482_probe(struct i2c_client *client,
const struct i2c_device_id *id);
-static int ds2482_detect(struct i2c_client *client, int kind,
- struct i2c_board_info *info);
static int ds2482_remove(struct i2c_client *client);
.probe = ds2482_probe,
.remove = ds2482_remove,
.id_table = ds2482_id,
- .detect = ds2482_detect,
- .address_data = &addr_data,
};
/*
}
-static int ds2482_detect(struct i2c_client *client, int kind,
- struct i2c_board_info *info)
-{
- if (!i2c_check_functionality(client->adapter,
- I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
- I2C_FUNC_SMBUS_BYTE))
- return -ENODEV;
-
- strlcpy(info->type, "ds2482", I2C_NAME_SIZE);
-
- return 0;
-}
-
static int ds2482_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
int temp1;
int idx;
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
+ I2C_FUNC_SMBUS_BYTE))
+ return -ENODEV;
+
if (!(data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL))) {
err = -ENOMEM;
goto exit;
return error;
}
-static void w1_cn_callback(struct cn_msg *msg)
+static void w1_cn_callback(struct cn_msg *msg, struct netlink_skb_parms *nsp)
{
struct w1_netlink_msg *m = (struct w1_netlink_msg *)(msg + 1);
struct w1_netlink_cmd *cmd;
To compile this driver as a module, choose M here: the
module will be called nuc900_wdt.
+config ADX_WATCHDOG
+ tristate "Avionic Design Xanthos watchdog"
+ depends on ARCH_PXA_ADX
+ help
+ Say Y here if you want support for the watchdog timer on Avionic
+ Design Xanthos boards.
+
# AVR32 Architecture
config AT32AP700X_WDT
obj-$(CONFIG_COH901327_WATCHDOG) += coh901327_wdt.o
obj-$(CONFIG_STMP3XXX_WATCHDOG) += stmp3xxx_wdt.o
obj-$(CONFIG_NUC900_WATCHDOG) += nuc900_wdt.o
+obj-$(CONFIG_ADX_WATCHDOG) += adx_wdt.o
# AVR32 Architecture
obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
--- /dev/null
+/*
+ * Copyright (C) 2008-2009 Avionic Design GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/fs.h>
+#include <linux/io.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+#include <linux/watchdog.h>
+
+#define WATCHDOG_NAME "adx-wdt"
+
+/* register offsets */
+#define ADX_WDT_CONTROL 0x00
+#define ADX_WDT_CONTROL_ENABLE (1 << 0)
+#define ADX_WDT_CONTROL_nRESET (1 << 1)
+#define ADX_WDT_TIMEOUT 0x08
+
+static struct platform_device *adx_wdt_dev;
+static unsigned long driver_open;
+
+#define WDT_STATE_STOP 0
+#define WDT_STATE_START 1
+
+struct adx_wdt {
+ void __iomem *base;
+ unsigned long timeout;
+ unsigned int state;
+ unsigned int wake;
+ spinlock_t lock;
+};
+
+static struct watchdog_info adx_wdt_info = {
+ .identity = "Avionic Design Xanthos Watchdog",
+ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
+};
+
+static void adx_wdt_start_locked(struct adx_wdt *wdt)
+{
+ u32 ctrl;
+
+ ctrl = readl(wdt->base + ADX_WDT_CONTROL);
+ ctrl |= ADX_WDT_CONTROL_ENABLE;
+ writel(ctrl, wdt->base + ADX_WDT_CONTROL);
+ wdt->state = WDT_STATE_START;
+}
+
+static void adx_wdt_start(struct adx_wdt *wdt)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt->lock, flags);
+ adx_wdt_start_locked(wdt);
+ spin_unlock_irqrestore(&wdt->lock, flags);
+}
+
+static void adx_wdt_stop_locked(struct adx_wdt *wdt)
+{
+ u32 ctrl;
+
+ ctrl = readl(wdt->base + ADX_WDT_CONTROL);
+ ctrl &= ~ADX_WDT_CONTROL_ENABLE;
+ writel(ctrl, wdt->base + ADX_WDT_CONTROL);
+ wdt->state = WDT_STATE_STOP;
+}
+
+static void adx_wdt_stop(struct adx_wdt *wdt)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt->lock, flags);
+ adx_wdt_stop_locked(wdt);
+ spin_unlock_irqrestore(&wdt->lock, flags);
+}
+
+static void adx_wdt_set_timeout(struct adx_wdt *wdt, unsigned long seconds)
+{
+ unsigned long timeout = seconds * 1000;
+ unsigned long flags;
+ unsigned int state;
+
+ spin_lock_irqsave(&wdt->lock, flags);
+ state = wdt->state;
+ adx_wdt_stop_locked(wdt);
+ writel(timeout, wdt->base + ADX_WDT_TIMEOUT);
+
+ if (state == WDT_STATE_START)
+ adx_wdt_start_locked(wdt);
+
+ wdt->timeout = timeout;
+ spin_unlock_irqrestore(&wdt->lock, flags);
+}
+
+static void adx_wdt_get_timeout(struct adx_wdt *wdt, unsigned long *seconds)
+{
+ *seconds = wdt->timeout / 1000;
+}
+
+static void adx_wdt_keepalive(struct adx_wdt *wdt)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&wdt->lock, flags);
+ writel(wdt->timeout, wdt->base + ADX_WDT_TIMEOUT);
+ spin_unlock_irqrestore(&wdt->lock, flags);
+}
+
+static int adx_wdt_open(struct inode *inode, struct file *file)
+{
+ struct adx_wdt *wdt = platform_get_drvdata(adx_wdt_dev);
+
+ if (test_and_set_bit(0, &driver_open))
+ return -EBUSY;
+
+ file->private_data = wdt;
+ adx_wdt_set_timeout(wdt, 30);
+ adx_wdt_start(wdt);
+
+ return nonseekable_open(inode, file);
+}
+
+static int adx_wdt_release(struct inode *inode, struct file *file)
+{
+ struct adx_wdt *wdt = file->private_data;
+
+ adx_wdt_stop(wdt);
+ clear_bit(0, &driver_open);
+
+ return 0;
+}
+
+static long adx_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ struct adx_wdt *wdt = file->private_data;
+ void __user *argp = (void __user *)arg;
+ unsigned long __user *p = argp;
+ unsigned long seconds = 0;
+ unsigned int options;
+ long ret = -EINVAL;
+
+ switch (cmd) {
+ case WDIOC_GETSUPPORT:
+ if (copy_to_user(argp, &adx_wdt_info, sizeof(adx_wdt_info)))
+ return -EFAULT;
+ else
+ return 0;
+
+ case WDIOC_GETSTATUS:
+ case WDIOC_GETBOOTSTATUS:
+ return put_user(0, p);
+
+ case WDIOC_KEEPALIVE:
+ adx_wdt_keepalive(wdt);
+ return 0;
+
+ case WDIOC_SETTIMEOUT:
+ if (get_user(seconds, p))
+ return -EFAULT;
+
+ adx_wdt_set_timeout(wdt, seconds);
+
+ /* fallthrough */
+ case WDIOC_GETTIMEOUT:
+ adx_wdt_get_timeout(wdt, &seconds);
+ return put_user(seconds, p);
+
+ case WDIOC_SETOPTIONS:
+ if (copy_from_user(&options, argp, sizeof(options)))
+ return -EFAULT;
+
+ if (options & WDIOS_DISABLECARD) {
+ adx_wdt_stop(wdt);
+ ret = 0;
+ }
+
+ if (options & WDIOS_ENABLECARD) {
+ adx_wdt_start(wdt);
+ ret = 0;
+ }
+
+ return ret;
+
+ default:
+ break;
+ }
+
+ return -ENOTTY;
+}
+
+static ssize_t adx_wdt_write(struct file *file, const char __user *data,
+ size_t len, loff_t *ppos)
+{
+ struct adx_wdt *wdt = file->private_data;
+
+ if (len)
+ adx_wdt_keepalive(wdt);
+
+ return len;
+}
+
+static const struct file_operations adx_wdt_fops = {
+ .owner = THIS_MODULE,
+ .llseek = no_llseek,
+ .open = adx_wdt_open,
+ .release = adx_wdt_release,
+ .unlocked_ioctl = adx_wdt_ioctl,
+ .write = adx_wdt_write,
+};
+
+static struct miscdevice adx_wdt_miscdev = {
+ .minor = WATCHDOG_MINOR,
+ .name = "watchdog",
+ .fops = &adx_wdt_fops,
+};
+
+static int __devinit adx_wdt_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ struct adx_wdt *wdt;
+ int ret = 0;
+ u32 ctrl;
+
+ wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL);
+ if (!wdt) {
+ dev_err(&pdev->dev, "cannot allocate WDT structure\n");
+ return -ENOMEM;
+ }
+
+ spin_lock_init(&wdt->lock);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "cannot obtain I/O memory region\n");
+ return -ENXIO;
+ }
+
+ res = devm_request_mem_region(&pdev->dev, res->start,
+ res->end - res->start + 1, res->name);
+ if (!res) {
+ dev_err(&pdev->dev, "cannot request I/O memory region\n");
+ return -ENXIO;
+ }
+
+ wdt->base = devm_ioremap_nocache(&pdev->dev, res->start,
+ res->end - res->start + 1);
+ if (!wdt->base) {
+ dev_err(&pdev->dev, "cannot remap I/O memory region\n");
+ return -ENXIO;
+ }
+
+ /* disable watchdog and reboot on timeout */
+ ctrl = readl(wdt->base + ADX_WDT_CONTROL);
+ ctrl &= ~ADX_WDT_CONTROL_ENABLE;
+ ctrl &= ~ADX_WDT_CONTROL_nRESET;
+ writel(ctrl, wdt->base + ADX_WDT_CONTROL);
+
+ platform_set_drvdata(pdev, wdt);
+ adx_wdt_dev = pdev;
+
+ ret = misc_register(&adx_wdt_miscdev);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot register miscdev on minor %d "
+ "(err=%d)\n", WATCHDOG_MINOR, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int __devexit adx_wdt_remove(struct platform_device *pdev)
+{
+ struct adx_wdt *wdt = platform_get_drvdata(pdev);
+
+ misc_deregister(&adx_wdt_miscdev);
+ adx_wdt_stop(wdt);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static void adx_wdt_shutdown(struct platform_device *pdev)
+{
+ struct adx_wdt *wdt = platform_get_drvdata(pdev);
+ adx_wdt_stop(wdt);
+}
+
+#ifdef CONFIG_PM
+static int adx_wdt_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct adx_wdt *wdt = platform_get_drvdata(pdev);
+
+ wdt->wake = (wdt->state == WDT_STATE_START) ? 1 : 0;
+ adx_wdt_stop(wdt);
+
+ return 0;
+}
+
+static int adx_wdt_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct adx_wdt *wdt = platform_get_drvdata(pdev);
+
+ if (wdt->wake)
+ adx_wdt_start(wdt);
+
+ return 0;
+}
+
+static struct dev_pm_ops adx_wdt_pm_ops = {
+ .suspend = adx_wdt_suspend,
+ .resume = adx_wdt_resume,
+};
+
+# define ADX_WDT_PM_OPS (&adx_wdt_pm_ops)
+#else
+# define ADX_WDT_PM_OPS NULL
+#endif
+
+static struct platform_driver adx_wdt_driver = {
+ .probe = adx_wdt_probe,
+ .remove = __devexit_p(adx_wdt_remove),
+ .shutdown = adx_wdt_shutdown,
+ .driver = {
+ .name = WATCHDOG_NAME,
+ .owner = THIS_MODULE,
+ .pm = ADX_WDT_PM_OPS,
+ },
+};
+
+static int __init adx_wdt_init(void)
+{
+ return platform_driver_register(&adx_wdt_driver);
+}
+
+static void __exit adx_wdt_exit(void)
+{
+ platform_driver_unregister(&adx_wdt_driver);
+}
+
+module_init(adx_wdt_init);
+module_exit(adx_wdt_exit);
+
+MODULE_DESCRIPTION("Avionic Design Xanthos Watchdog Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Thierry Reding <thierry.reding@avionic-design.de>");
+MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR);
#include <linux/fs.h>
#include <linux/poll.h>
#include <linux/mutex.h>
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/mount.h>
#include <linux/pagemap.h>
adfs_get_block(struct inode *inode, sector_t block, struct buffer_head *bh,
int create)
{
- if (block < 0)
- goto abort_negative;
-
if (!create) {
if (block >= inode->i_blocks)
goto abort_toobig;
/* don't support allocation of blocks yet */
return -EIO;
-abort_negative:
- adfs_error(inode->i_sb, "block %d < 0", block);
- return -EIO;
-
abort_toobig:
return 0;
}
+++ /dev/null
-/* AFS local cache management interface
- *
- * Copyright (C) 2008 Red Hat, Inc. All Rights Reserved.
- * Written by David Howells (dhowells@redhat.com)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/fscache.h>
#include <linux/key.h>
#include <linux/workqueue.h>
#include <linux/sched.h>
+#include <linux/fscache.h>
#include "afs.h"
#include "afs_vl.h"
-#include "cache.h"
#define AFS_CELL_MAX_ADDRS 15
*
*/
+#include <linux/cred.h>
#include <linux/file.h>
#include <linux/poll.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/fs.h>
/* Taken over from the old code... */
/* POSIX UID/GID verification for setting inode attributes. */
-int inode_change_ok(struct inode *inode, struct iattr *attr)
+int inode_change_ok(const struct inode *inode, struct iattr *attr)
{
int retval = -EPERM;
unsigned int ia_valid = attr->ia_valid;
error:
return retval;
}
-
EXPORT_SYMBOL(inode_change_ok);
+/**
+ * inode_newsize_ok - may this inode be truncated to a given size
+ * @inode: the inode to be truncated
+ * @offset: the new size to assign to the inode
+ * @Returns: 0 on success, -ve errno on failure
+ *
+ * inode_newsize_ok will check filesystem limits and ulimits to check that the
+ * new inode size is within limits. inode_newsize_ok will also send SIGXFSZ
+ * when necessary. Caller must not proceed with inode size change if failure is
+ * returned. @inode must be a file (not directory), with appropriate
+ * permissions to allow truncate (inode_newsize_ok does NOT check these
+ * conditions).
+ *
+ * inode_newsize_ok must be called with i_mutex held.
+ */
+int inode_newsize_ok(const struct inode *inode, loff_t offset)
+{
+ if (inode->i_size < offset) {
+ unsigned long limit;
+
+ limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
+ if (limit != RLIM_INFINITY && offset > limit)
+ goto out_sig;
+ if (offset > inode->i_sb->s_maxbytes)
+ goto out_big;
+ } else {
+ /*
+ * truncation of in-use swapfiles is disallowed - it would
+ * cause subsequent swapout to scribble on the now-freed
+ * blocks.
+ */
+ if (IS_SWAPFILE(inode))
+ return -ETXTBSY;
+ }
+
+ return 0;
+out_sig:
+ send_sig(SIGXFSZ, current, 0);
+out_big:
+ return -EFBIG;
+}
+EXPORT_SYMBOL(inode_newsize_ok);
+
int inode_setattr(struct inode * inode, struct iattr * attr)
{
unsigned int ia_valid = attr->ia_valid;
{
kfree(BEFS_SB(sb)->mount_opts.iocharset);
BEFS_SB(sb)->mount_opts.iocharset = NULL;
-
- if (BEFS_SB(sb)->nls) {
- unload_nls(BEFS_SB(sb)->nls);
- BEFS_SB(sb)->nls = NULL;
- }
-
+ unload_nls(BEFS_SB(sb)->nls);
kfree(sb->s_fs_info);
sb->s_fs_info = NULL;
}
int numnote;
};
-static int fill_note_info(struct elfhdr *elf, int phdrs,
- struct elf_note_info *info,
- long signr, struct pt_regs *regs)
+static int elf_note_info_init(struct elf_note_info *info)
{
-#define NUM_NOTES 6
- struct list_head *t;
-
- info->notes = NULL;
- info->prstatus = NULL;
- info->psinfo = NULL;
- info->fpu = NULL;
-#ifdef ELF_CORE_COPY_XFPREGS
- info->xfpu = NULL;
-#endif
+ memset(info, 0, sizeof(*info));
INIT_LIST_HEAD(&info->thread_list);
- info->notes = kmalloc(NUM_NOTES * sizeof(struct memelfnote),
- GFP_KERNEL);
+ /* Allocate space for six ELF notes */
+ info->notes = kmalloc(6 * sizeof(struct memelfnote), GFP_KERNEL);
if (!info->notes)
return 0;
info->psinfo = kmalloc(sizeof(*info->psinfo), GFP_KERNEL);
if (!info->psinfo)
- return 0;
+ goto notes_free;
info->prstatus = kmalloc(sizeof(*info->prstatus), GFP_KERNEL);
if (!info->prstatus)
- return 0;
+ goto psinfo_free;
info->fpu = kmalloc(sizeof(*info->fpu), GFP_KERNEL);
if (!info->fpu)
- return 0;
+ goto prstatus_free;
#ifdef ELF_CORE_COPY_XFPREGS
info->xfpu = kmalloc(sizeof(*info->xfpu), GFP_KERNEL);
if (!info->xfpu)
- return 0;
+ goto fpu_free;
+#endif
+ return 1;
+#ifdef ELF_CORE_COPY_XFPREGS
+ fpu_free:
+ kfree(info->fpu);
#endif
+ prstatus_free:
+ kfree(info->prstatus);
+ psinfo_free:
+ kfree(info->psinfo);
+ notes_free:
+ kfree(info->notes);
+ return 0;
+}
+
+static int fill_note_info(struct elfhdr *elf, int phdrs,
+ struct elf_note_info *info,
+ long signr, struct pt_regs *regs)
+{
+ struct list_head *t;
+
+ if (!elf_note_info_init(info))
+ return 0;
- info->thread_status_size = 0;
if (signr) {
struct core_thread *ct;
struct elf_thread_status *ets;
#endif
return 1;
-
-#undef NUM_NOTES
}
static size_t get_note_info_size(struct elf_note_info *info)
}
stack_size = exec_params.stack_size;
- if (stack_size < interp_params.stack_size)
- stack_size = interp_params.stack_size;
-
if (exec_params.flags & ELF_FDPIC_FLAG_EXEC_STACK)
executable_stack = EXSTACK_ENABLE_X;
else if (exec_params.flags & ELF_FDPIC_FLAG_NOEXEC_STACK)
executable_stack = EXSTACK_DISABLE_X;
- else if (interp_params.flags & ELF_FDPIC_FLAG_EXEC_STACK)
- executable_stack = EXSTACK_ENABLE_X;
- else if (interp_params.flags & ELF_FDPIC_FLAG_NOEXEC_STACK)
- executable_stack = EXSTACK_DISABLE_X;
else
executable_stack = EXSTACK_DEFAULT;
+ if (stack_size == 0) {
+ stack_size = interp_params.stack_size;
+ if (interp_params.flags & ELF_FDPIC_FLAG_EXEC_STACK)
+ executable_stack = EXSTACK_ENABLE_X;
+ else if (interp_params.flags & ELF_FDPIC_FLAG_NOEXEC_STACK)
+ executable_stack = EXSTACK_DISABLE_X;
+ else
+ executable_stack = EXSTACK_DEFAULT;
+ }
+
retval = -ENOEXEC;
if (stack_size == 0)
goto error;
ret = bprm->file->f_op->read(bprm->file, buf, LBUFSIZE, &fpos);
if (ret <= 0)
break;
- if (ret >= (unsigned long) -4096)
- break;
len -= ret;
strm.next_in = buf;
"(%d != %d)", (unsigned) r, curid, id);
goto failed;
} else if ( ! p->lib_list[id].loaded &&
- load_flat_shared_library(id, p) > (unsigned long) -4096) {
+ IS_ERR_VALUE(load_flat_shared_library(id, p))) {
printk("BINFMT_FLAT: failed to load library %d", id);
goto failed;
}
textpos = do_mmap(bprm->file, 0, text_len, PROT_READ|PROT_EXEC,
MAP_PRIVATE|MAP_EXECUTABLE, 0);
up_write(¤t->mm->mmap_sem);
- if (!textpos || textpos >= (unsigned long) -4096) {
+ if (!textpos || IS_ERR_VALUE(textpos)) {
if (!textpos)
textpos = (unsigned long) -ENOMEM;
printk("Unable to mmap process text, errno %d\n", (int)-textpos);
PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE, 0);
up_write(¤t->mm->mmap_sem);
- if (realdatastart == 0 || realdatastart >= (unsigned long)-4096) {
+ if (realdatastart == 0 || IS_ERR_VALUE(realdatastart)) {
if (!realdatastart)
realdatastart = (unsigned long) -ENOMEM;
printk("Unable to allocate RAM for process data, errno %d\n",
result = bprm->file->f_op->read(bprm->file, (char *) datapos,
data_len + (relocs * sizeof(unsigned long)), &fpos);
}
- if (result >= (unsigned long)-4096) {
+ if (IS_ERR_VALUE(result)) {
printk("Unable to read data+bss, errno %d\n", (int)-result);
do_munmap(current->mm, textpos, text_len);
do_munmap(current->mm, realdatastart, data_len + extra);
PROT_READ | PROT_EXEC | PROT_WRITE, MAP_PRIVATE, 0);
up_write(¤t->mm->mmap_sem);
- if (!textpos || textpos >= (unsigned long) -4096) {
+ if (!textpos || IS_ERR_VALUE(textpos)) {
if (!textpos)
textpos = (unsigned long) -ENOMEM;
printk("Unable to allocate RAM for process text/data, errno %d\n",
fpos = 0;
result = bprm->file->f_op->read(bprm->file,
(char *) textpos, text_len, &fpos);
- if (result < (unsigned long) -4096)
+ if (!IS_ERR_VALUE(result))
result = decompress_exec(bprm, text_len, (char *) datapos,
data_len + (relocs * sizeof(unsigned long)), 0);
}
fpos = 0;
result = bprm->file->f_op->read(bprm->file,
(char *) textpos, text_len, &fpos);
- if (result < (unsigned long) -4096) {
+ if (!IS_ERR_VALUE(result)) {
fpos = ntohl(hdr->data_start);
result = bprm->file->f_op->read(bprm->file, (char *) datapos,
data_len + (relocs * sizeof(unsigned long)), &fpos);
}
}
- if (result >= (unsigned long)-4096) {
+ if (IS_ERR_VALUE(result)) {
printk("Unable to read code+data+bss, errno %d\n",(int)-result);
do_munmap(current->mm, textpos, text_len + data_len + extra +
MAX_SHARED_LIBS * sizeof(unsigned long));
res = prepare_binprm(&bprm);
- if (res <= (unsigned long)-4096)
+ if (!IS_ERR_VALUE(res))
res = load_flat_file(&bprm, libs, id, NULL);
abort_creds(bprm.cred);
stack_len += FLAT_DATA_ALIGN - 1; /* reserve for upcoming alignment */
res = load_flat_file(bprm, &libinfo, 0, &stack_len);
- if (res > (unsigned long)-4096)
+ if (IS_ERR_VALUE(res))
return res;
/* Update data segment pointers for all libraries */
mempool_free(p, bs->bio_pool);
}
+EXPORT_SYMBOL(bio_free);
void bio_init(struct bio *bio)
{
bio->bi_comp_cpu = -1;
atomic_set(&bio->bi_cnt, 1);
}
+EXPORT_SYMBOL(bio_init);
/**
* bio_alloc_bioset - allocate a bio for I/O
mempool_free(p, bs->bio_pool);
return NULL;
}
+EXPORT_SYMBOL(bio_alloc_bioset);
static void bio_fs_destructor(struct bio *bio)
{
return bio;
}
+EXPORT_SYMBOL(bio_alloc);
static void bio_kmalloc_destructor(struct bio *bio)
{
return bio;
}
+EXPORT_SYMBOL(bio_kmalloc);
void zero_fill_bio(struct bio *bio)
{
bio->bi_destructor(bio);
}
}
+EXPORT_SYMBOL(bio_put);
inline int bio_phys_segments(struct request_queue *q, struct bio *bio)
{
return bio->bi_phys_segments;
}
+EXPORT_SYMBOL(bio_phys_segments);
/**
* __bio_clone - clone a bio
bio->bi_size = bio_src->bi_size;
bio->bi_idx = bio_src->bi_idx;
}
+EXPORT_SYMBOL(__bio_clone);
/**
* bio_clone - clone a bio
return b;
}
+EXPORT_SYMBOL(bio_clone);
/**
* bio_get_nr_vecs - return approx number of vecs
return nr_pages;
}
+EXPORT_SYMBOL(bio_get_nr_vecs);
static int __bio_add_page(struct request_queue *q, struct bio *bio, struct page
*page, unsigned int len, unsigned int offset,
return __bio_add_page(q, bio, page, len, offset,
queue_max_hw_sectors(q));
}
+EXPORT_SYMBOL(bio_add_pc_page);
/**
* bio_add_page - attempt to add page to bio
struct request_queue *q = bdev_get_queue(bio->bi_bdev);
return __bio_add_page(q, bio, page, len, offset, queue_max_sectors(q));
}
+EXPORT_SYMBOL(bio_add_page);
struct bio_map_data {
struct bio_vec *iovecs;
bio_put(bio);
return ret;
}
+EXPORT_SYMBOL(bio_uncopy_user);
/**
* bio_copy_user_iov - copy user data to bio
return bio_copy_user_iov(q, map_data, &iov, 1, write_to_vm, gfp_mask);
}
+EXPORT_SYMBOL(bio_copy_user);
static struct bio *__bio_map_user_iov(struct request_queue *q,
struct block_device *bdev,
return bio_map_user_iov(q, bdev, &iov, 1, write_to_vm, gfp_mask);
}
+EXPORT_SYMBOL(bio_map_user);
/**
* bio_map_user_iov - map user sg_iovec table into bio
__bio_unmap_user(bio);
bio_put(bio);
}
+EXPORT_SYMBOL(bio_unmap_user);
static void bio_map_kern_endio(struct bio *bio, int err)
{
bio_put(bio);
}
-
static struct bio *__bio_map_kern(struct request_queue *q, void *data,
unsigned int len, gfp_t gfp_mask)
{
bio_put(bio);
return ERR_PTR(-EINVAL);
}
+EXPORT_SYMBOL(bio_map_kern);
static void bio_copy_kern_endio(struct bio *bio, int err)
{
return bio;
}
+EXPORT_SYMBOL(bio_copy_kern);
/*
* bio_set_pages_dirty() and bio_check_pages_dirty() are support functions
if (bio->bi_end_io)
bio->bi_end_io(bio, error);
}
+EXPORT_SYMBOL(bio_endio);
void bio_pair_release(struct bio_pair *bp)
{
mempool_free(bp, bp->bio2.bi_private);
}
}
+EXPORT_SYMBOL(bio_pair_release);
static void bio_pair_end_1(struct bio *bi, int err)
{
return bp;
}
+EXPORT_SYMBOL(bio_split);
/**
* bio_sector_offset - Find hardware sector offset in bio
kfree(bs);
}
+EXPORT_SYMBOL(bioset_free);
/**
* bioset_create - Create a bio_set
bioset_free(bs);
return NULL;
}
+EXPORT_SYMBOL(bioset_create);
static void __init biovec_init_slabs(void)
{
return 0;
}
-
subsys_initcall(init_bio);
-
-EXPORT_SYMBOL(bio_alloc);
-EXPORT_SYMBOL(bio_kmalloc);
-EXPORT_SYMBOL(bio_put);
-EXPORT_SYMBOL(bio_free);
-EXPORT_SYMBOL(bio_endio);
-EXPORT_SYMBOL(bio_init);
-EXPORT_SYMBOL(__bio_clone);
-EXPORT_SYMBOL(bio_clone);
-EXPORT_SYMBOL(bio_phys_segments);
-EXPORT_SYMBOL(bio_add_page);
-EXPORT_SYMBOL(bio_add_pc_page);
-EXPORT_SYMBOL(bio_get_nr_vecs);
-EXPORT_SYMBOL(bio_map_user);
-EXPORT_SYMBOL(bio_unmap_user);
-EXPORT_SYMBOL(bio_map_kern);
-EXPORT_SYMBOL(bio_copy_kern);
-EXPORT_SYMBOL(bio_pair_release);
-EXPORT_SYMBOL(bio_split);
-EXPORT_SYMBOL(bio_copy_user);
-EXPORT_SYMBOL(bio_uncopy_user);
-EXPORT_SYMBOL(bioset_create);
-EXPORT_SYMBOL(bioset_free);
-EXPORT_SYMBOL(bio_alloc_bioset);
* freeze_bdev -- lock a filesystem and force it into a consistent state
* @bdev: blockdevice to lock
*
- * This takes the block device bd_mount_sem to make sure no new mounts
- * happen on bdev until thaw_bdev() is called.
* If a superblock is found on this device, we take the s_umount semaphore
* on it to make sure nobody unmounts until the snapshot creation is done.
* The reference counter (bd_fsfreeze_count) guarantees that only the last
int error = 0;
mutex_lock(&bdev->bd_fsfreeze_mutex);
- if (bdev->bd_fsfreeze_count > 0) {
- bdev->bd_fsfreeze_count++;
+ if (++bdev->bd_fsfreeze_count > 1) {
+ /*
+ * We don't even need to grab a reference - the first call
+ * to freeze_bdev grab an active reference and only the last
+ * thaw_bdev drops it.
+ */
sb = get_super(bdev);
+ drop_super(sb);
mutex_unlock(&bdev->bd_fsfreeze_mutex);
return sb;
}
- bdev->bd_fsfreeze_count++;
-
- down(&bdev->bd_mount_sem);
- sb = get_super(bdev);
- if (sb && !(sb->s_flags & MS_RDONLY)) {
- sb->s_frozen = SB_FREEZE_WRITE;
- smp_wmb();
-
- sync_filesystem(sb);
-
- sb->s_frozen = SB_FREEZE_TRANS;
- smp_wmb();
-
- sync_blockdev(sb->s_bdev);
-
- if (sb->s_op->freeze_fs) {
- error = sb->s_op->freeze_fs(sb);
- if (error) {
- printk(KERN_ERR
- "VFS:Filesystem freeze failed\n");
- sb->s_frozen = SB_UNFROZEN;
- drop_super(sb);
- up(&bdev->bd_mount_sem);
- bdev->bd_fsfreeze_count--;
- mutex_unlock(&bdev->bd_fsfreeze_mutex);
- return ERR_PTR(error);
- }
+
+ sb = get_active_super(bdev);
+ if (!sb)
+ goto out;
+ if (sb->s_flags & MS_RDONLY) {
+ deactivate_locked_super(sb);
+ mutex_unlock(&bdev->bd_fsfreeze_mutex);
+ return sb;
+ }
+
+ sb->s_frozen = SB_FREEZE_WRITE;
+ smp_wmb();
+
+ sync_filesystem(sb);
+
+ sb->s_frozen = SB_FREEZE_TRANS;
+ smp_wmb();
+
+ sync_blockdev(sb->s_bdev);
+
+ if (sb->s_op->freeze_fs) {
+ error = sb->s_op->freeze_fs(sb);
+ if (error) {
+ printk(KERN_ERR
+ "VFS:Filesystem freeze failed\n");
+ sb->s_frozen = SB_UNFROZEN;
+ deactivate_locked_super(sb);
+ bdev->bd_fsfreeze_count--;
+ mutex_unlock(&bdev->bd_fsfreeze_mutex);
+ return ERR_PTR(error);
}
}
+ up_write(&sb->s_umount);
+ out:
sync_blockdev(bdev);
mutex_unlock(&bdev->bd_fsfreeze_mutex);
-
- return sb; /* thaw_bdev releases s->s_umount and bd_mount_sem */
+ return sb; /* thaw_bdev releases s->s_umount */
}
EXPORT_SYMBOL(freeze_bdev);
*/
int thaw_bdev(struct block_device *bdev, struct super_block *sb)
{
- int error = 0;
+ int error = -EINVAL;
mutex_lock(&bdev->bd_fsfreeze_mutex);
- if (!bdev->bd_fsfreeze_count) {
- mutex_unlock(&bdev->bd_fsfreeze_mutex);
- return -EINVAL;
- }
-
- bdev->bd_fsfreeze_count--;
- if (bdev->bd_fsfreeze_count > 0) {
- if (sb)
- drop_super(sb);
- mutex_unlock(&bdev->bd_fsfreeze_mutex);
- return 0;
- }
-
- if (sb) {
- BUG_ON(sb->s_bdev != bdev);
- if (!(sb->s_flags & MS_RDONLY)) {
- if (sb->s_op->unfreeze_fs) {
- error = sb->s_op->unfreeze_fs(sb);
- if (error) {
- printk(KERN_ERR
- "VFS:Filesystem thaw failed\n");
- sb->s_frozen = SB_FREEZE_TRANS;
- bdev->bd_fsfreeze_count++;
- mutex_unlock(&bdev->bd_fsfreeze_mutex);
- return error;
- }
- }
- sb->s_frozen = SB_UNFROZEN;
- smp_wmb();
- wake_up(&sb->s_wait_unfrozen);
+ if (!bdev->bd_fsfreeze_count)
+ goto out_unlock;
+
+ error = 0;
+ if (--bdev->bd_fsfreeze_count > 0)
+ goto out_unlock;
+
+ if (!sb)
+ goto out_unlock;
+
+ BUG_ON(sb->s_bdev != bdev);
+ down_write(&sb->s_umount);
+ if (sb->s_flags & MS_RDONLY)
+ goto out_deactivate;
+
+ if (sb->s_op->unfreeze_fs) {
+ error = sb->s_op->unfreeze_fs(sb);
+ if (error) {
+ printk(KERN_ERR
+ "VFS:Filesystem thaw failed\n");
+ sb->s_frozen = SB_FREEZE_TRANS;
+ bdev->bd_fsfreeze_count++;
+ mutex_unlock(&bdev->bd_fsfreeze_mutex);
+ return error;
}
- drop_super(sb);
}
- up(&bdev->bd_mount_sem);
+ sb->s_frozen = SB_UNFROZEN;
+ smp_wmb();
+ wake_up(&sb->s_wait_unfrozen);
+
+out_deactivate:
+ if (sb)
+ deactivate_locked_super(sb);
+out_unlock:
mutex_unlock(&bdev->bd_fsfreeze_mutex);
return 0;
}
memset(bdev, 0, sizeof(*bdev));
mutex_init(&bdev->bd_mutex);
- sema_init(&bdev->bd_mount_sem, 1);
INIT_LIST_HEAD(&bdev->bd_inodes);
INIT_LIST_HEAD(&bdev->bd_list);
#ifdef CONFIG_SYSFS
#include "btrfs_inode.h"
#include "xattr.h"
-#ifdef CONFIG_FS_POSIX_ACL
+#ifdef CONFIG_BTRFS_POSIX_ACL
static struct posix_acl *btrfs_get_acl(struct inode *inode, int type)
{
.set = btrfs_xattr_acl_access_set,
};
-#else /* CONFIG_FS_POSIX_ACL */
+#else /* CONFIG_BTRFS_POSIX_ACL */
int btrfs_acl_chmod(struct inode *inode)
{
return 0;
}
-#endif /* CONFIG_FS_POSIX_ACL */
+#endif /* CONFIG_BTRFS_POSIX_ACL */
/* number of things on the pending list */
atomic_t num_pending;
+ /* reference counter for this struct */
+ atomic_t refs;
+
unsigned long sequence;
/* protects the pending list. */
unsigned long flags;
spin_lock_irqsave(&worker->workers->lock, flags);
worker->idle = 1;
- list_move(&worker->worker_list, &worker->workers->idle_list);
+
+ /* the list may be empty if the worker is just starting */
+ if (!list_empty(&worker->worker_list)) {
+ list_move(&worker->worker_list,
+ &worker->workers->idle_list);
+ }
spin_unlock_irqrestore(&worker->workers->lock, flags);
}
}
unsigned long flags;
spin_lock_irqsave(&worker->workers->lock, flags);
worker->idle = 0;
- list_move_tail(&worker->worker_list,
- &worker->workers->worker_list);
+
+ if (!list_empty(&worker->worker_list)) {
+ list_move_tail(&worker->worker_list,
+ &worker->workers->worker_list);
+ }
spin_unlock_irqrestore(&worker->workers->lock, flags);
}
}
-static noinline int run_ordered_completions(struct btrfs_workers *workers,
- struct btrfs_work *work)
+static void check_pending_worker_creates(struct btrfs_worker_thread *worker)
{
+ struct btrfs_workers *workers = worker->workers;
unsigned long flags;
+ rmb();
+ if (!workers->atomic_start_pending)
+ return;
+
+ spin_lock_irqsave(&workers->lock, flags);
+ if (!workers->atomic_start_pending)
+ goto out;
+
+ workers->atomic_start_pending = 0;
+ if (workers->num_workers >= workers->max_workers)
+ goto out;
+
+ spin_unlock_irqrestore(&workers->lock, flags);
+ btrfs_start_workers(workers, 1);
+ return;
+
+out:
+ spin_unlock_irqrestore(&workers->lock, flags);
+}
+
+static noinline int run_ordered_completions(struct btrfs_workers *workers,
+ struct btrfs_work *work)
+{
if (!workers->ordered)
return 0;
set_bit(WORK_DONE_BIT, &work->flags);
- spin_lock_irqsave(&workers->lock, flags);
+ spin_lock(&workers->order_lock);
while (1) {
if (!list_empty(&workers->prio_order_list)) {
if (test_and_set_bit(WORK_ORDER_DONE_BIT, &work->flags))
break;
- spin_unlock_irqrestore(&workers->lock, flags);
+ spin_unlock(&workers->order_lock);
work->ordered_func(work);
/* now take the lock again and call the freeing code */
- spin_lock_irqsave(&workers->lock, flags);
+ spin_lock(&workers->order_lock);
list_del(&work->order_list);
work->ordered_free(work);
}
- spin_unlock_irqrestore(&workers->lock, flags);
+ spin_unlock(&workers->order_lock);
return 0;
}
+static void put_worker(struct btrfs_worker_thread *worker)
+{
+ if (atomic_dec_and_test(&worker->refs))
+ kfree(worker);
+}
+
+static int try_worker_shutdown(struct btrfs_worker_thread *worker)
+{
+ int freeit = 0;
+
+ spin_lock_irq(&worker->lock);
+ spin_lock(&worker->workers->lock);
+ if (worker->workers->num_workers > 1 &&
+ worker->idle &&
+ !worker->working &&
+ !list_empty(&worker->worker_list) &&
+ list_empty(&worker->prio_pending) &&
+ list_empty(&worker->pending) &&
+ atomic_read(&worker->num_pending) == 0) {
+ freeit = 1;
+ list_del_init(&worker->worker_list);
+ worker->workers->num_workers--;
+ }
+ spin_unlock(&worker->workers->lock);
+ spin_unlock_irq(&worker->lock);
+
+ if (freeit)
+ put_worker(worker);
+ return freeit;
+}
+
+static struct btrfs_work *get_next_work(struct btrfs_worker_thread *worker,
+ struct list_head *prio_head,
+ struct list_head *head)
+{
+ struct btrfs_work *work = NULL;
+ struct list_head *cur = NULL;
+
+ if(!list_empty(prio_head))
+ cur = prio_head->next;
+
+ smp_mb();
+ if (!list_empty(&worker->prio_pending))
+ goto refill;
+
+ if (!list_empty(head))
+ cur = head->next;
+
+ if (cur)
+ goto out;
+
+refill:
+ spin_lock_irq(&worker->lock);
+ list_splice_tail_init(&worker->prio_pending, prio_head);
+ list_splice_tail_init(&worker->pending, head);
+
+ if (!list_empty(prio_head))
+ cur = prio_head->next;
+ else if (!list_empty(head))
+ cur = head->next;
+ spin_unlock_irq(&worker->lock);
+
+ if (!cur)
+ goto out_fail;
+
+out:
+ work = list_entry(cur, struct btrfs_work, list);
+
+out_fail:
+ return work;
+}
+
/*
* main loop for servicing work items
*/
static int worker_loop(void *arg)
{
struct btrfs_worker_thread *worker = arg;
- struct list_head *cur;
+ struct list_head head;
+ struct list_head prio_head;
struct btrfs_work *work;
+
+ INIT_LIST_HEAD(&head);
+ INIT_LIST_HEAD(&prio_head);
+
do {
- spin_lock_irq(&worker->lock);
-again_locked:
+again:
while (1) {
- if (!list_empty(&worker->prio_pending))
- cur = worker->prio_pending.next;
- else if (!list_empty(&worker->pending))
- cur = worker->pending.next;
- else
+
+
+ work = get_next_work(worker, &prio_head, &head);
+ if (!work)
break;
- work = list_entry(cur, struct btrfs_work, list);
list_del(&work->list);
clear_bit(WORK_QUEUED_BIT, &work->flags);
work->worker = worker;
- spin_unlock_irq(&worker->lock);
work->func(work);
*/
run_ordered_completions(worker->workers, work);
- spin_lock_irq(&worker->lock);
- check_idle_worker(worker);
+ check_pending_worker_creates(worker);
+
}
+
+ spin_lock_irq(&worker->lock);
+ check_idle_worker(worker);
+
if (freezing(current)) {
worker->working = 0;
spin_unlock_irq(&worker->lock);
spin_lock_irq(&worker->lock);
set_current_state(TASK_INTERRUPTIBLE);
if (!list_empty(&worker->pending) ||
- !list_empty(&worker->prio_pending))
- goto again_locked;
+ !list_empty(&worker->prio_pending)) {
+ spin_unlock_irq(&worker->lock);
+ goto again;
+ }
/*
* this makes sure we get a wakeup when someone
worker->working = 0;
spin_unlock_irq(&worker->lock);
- if (!kthread_should_stop())
- schedule();
+ if (!kthread_should_stop()) {
+ schedule_timeout(HZ * 120);
+ if (!worker->working &&
+ try_worker_shutdown(worker)) {
+ return 0;
+ }
+ }
}
__set_current_state(TASK_RUNNING);
}
{
struct list_head *cur;
struct btrfs_worker_thread *worker;
+ int can_stop;
+ spin_lock_irq(&workers->lock);
list_splice_init(&workers->idle_list, &workers->worker_list);
while (!list_empty(&workers->worker_list)) {
cur = workers->worker_list.next;
worker = list_entry(cur, struct btrfs_worker_thread,
worker_list);
- kthread_stop(worker->task);
- list_del(&worker->worker_list);
- kfree(worker);
+
+ atomic_inc(&worker->refs);
+ workers->num_workers -= 1;
+ if (!list_empty(&worker->worker_list)) {
+ list_del_init(&worker->worker_list);
+ put_worker(worker);
+ can_stop = 1;
+ } else
+ can_stop = 0;
+ spin_unlock_irq(&workers->lock);
+ if (can_stop)
+ kthread_stop(worker->task);
+ spin_lock_irq(&workers->lock);
+ put_worker(worker);
}
+ spin_unlock_irq(&workers->lock);
return 0;
}
INIT_LIST_HEAD(&workers->order_list);
INIT_LIST_HEAD(&workers->prio_order_list);
spin_lock_init(&workers->lock);
+ spin_lock_init(&workers->order_lock);
workers->max_workers = max;
workers->idle_thresh = 32;
workers->name = name;
workers->ordered = 0;
+ workers->atomic_start_pending = 0;
+ workers->atomic_worker_start = 0;
}
/*
INIT_LIST_HEAD(&worker->prio_pending);
INIT_LIST_HEAD(&worker->worker_list);
spin_lock_init(&worker->lock);
+
atomic_set(&worker->num_pending, 0);
+ atomic_set(&worker->refs, 1);
worker->workers = workers;
worker->task = kthread_run(worker_loop, worker,
"btrfs-%s-%d", workers->name,
kfree(worker);
goto fail;
}
-
spin_lock_irq(&workers->lock);
list_add_tail(&worker->worker_list, &workers->idle_list);
worker->idle = 1;
*/
next = workers->worker_list.next;
worker = list_entry(next, struct btrfs_worker_thread, worker_list);
- atomic_inc(&worker->num_pending);
worker->sequence++;
if (worker->sequence % workers->idle_thresh == 0)
{
struct btrfs_worker_thread *worker;
unsigned long flags;
+ struct list_head *fallback;
again:
spin_lock_irqsave(&workers->lock, flags);
worker = next_worker(workers);
- spin_unlock_irqrestore(&workers->lock, flags);
if (!worker) {
- spin_lock_irqsave(&workers->lock, flags);
if (workers->num_workers >= workers->max_workers) {
- struct list_head *fallback = NULL;
- /*
- * we have failed to find any workers, just
- * return the force one
- */
- if (!list_empty(&workers->worker_list))
- fallback = workers->worker_list.next;
- if (!list_empty(&workers->idle_list))
- fallback = workers->idle_list.next;
- BUG_ON(!fallback);
- worker = list_entry(fallback,
- struct btrfs_worker_thread, worker_list);
- spin_unlock_irqrestore(&workers->lock, flags);
+ goto fallback;
+ } else if (workers->atomic_worker_start) {
+ workers->atomic_start_pending = 1;
+ goto fallback;
} else {
spin_unlock_irqrestore(&workers->lock, flags);
/* we're below the limit, start another worker */
goto again;
}
}
+ goto found;
+
+fallback:
+ fallback = NULL;
+ /*
+ * we have failed to find any workers, just
+ * return the first one we can find.
+ */
+ if (!list_empty(&workers->worker_list))
+ fallback = workers->worker_list.next;
+ if (!list_empty(&workers->idle_list))
+ fallback = workers->idle_list.next;
+ BUG_ON(!fallback);
+ worker = list_entry(fallback,
+ struct btrfs_worker_thread, worker_list);
+found:
+ /*
+ * this makes sure the worker doesn't exit before it is placed
+ * onto a busy/idle list
+ */
+ atomic_inc(&worker->num_pending);
+ spin_unlock_irqrestore(&workers->lock, flags);
return worker;
}
spin_lock(&worker->workers->lock);
worker->idle = 0;
list_move_tail(&worker->worker_list,
- &worker->workers->worker_list);
+ &worker->workers->worker_list);
spin_unlock(&worker->workers->lock);
}
if (!worker->working) {
worker->working = 1;
}
- spin_unlock_irqrestore(&worker->lock, flags);
if (wake)
wake_up_process(worker->task);
+ spin_unlock_irqrestore(&worker->lock, flags);
out:
return 0;
worker = find_worker(workers);
if (workers->ordered) {
- spin_lock_irqsave(&workers->lock, flags);
+ /*
+ * you're not allowed to do ordered queues from an
+ * interrupt handler
+ */
+ spin_lock(&workers->order_lock);
if (test_bit(WORK_HIGH_PRIO_BIT, &work->flags)) {
list_add_tail(&work->order_list,
&workers->prio_order_list);
} else {
list_add_tail(&work->order_list, &workers->order_list);
}
- spin_unlock_irqrestore(&workers->lock, flags);
+ spin_unlock(&workers->order_lock);
} else {
INIT_LIST_HEAD(&work->order_list);
}
list_add_tail(&work->list, &worker->prio_pending);
else
list_add_tail(&work->list, &worker->pending);
- atomic_inc(&worker->num_pending);
check_busy_worker(worker);
/*
wake = 1;
worker->working = 1;
- spin_unlock_irqrestore(&worker->lock, flags);
-
if (wake)
wake_up_process(worker->task);
+ spin_unlock_irqrestore(&worker->lock, flags);
+
out:
return 0;
}
/* force completions in the order they were queued */
int ordered;
+ /* more workers required, but in an interrupt handler */
+ int atomic_start_pending;
+
+ /*
+ * are we allowed to sleep while starting workers or are we required
+ * to start them at a later time?
+ */
+ int atomic_worker_start;
+
/* list with all the work threads. The workers on the idle thread
* may be actively servicing jobs, but they haven't yet hit the
* idle thresh limit above.
/* lock for finding the next worker thread to queue on */
spinlock_t lock;
+ /* lock for the ordered lists */
+ spinlock_t order_lock;
+
/* extra name for this worker, used for current->name */
char *name;
};
*/
u64 last_unlink_trans;
+ /*
+ * These two counters are for delalloc metadata reservations. We keep
+ * track of how many extents we've accounted for vs how many extents we
+ * have.
+ */
+ int delalloc_reserved_extents;
+ int delalloc_extents;
+
/*
* ordered_data_close is set by truncate when a file that used
* to have good data has been truncated to zero. When it is set
* of these.
*/
unsigned ordered_data_close:1;
+ unsigned dummy_inode:1;
struct inode vfs_inode;
};
*/
set_page_extent_mapped(page);
lock_extent(tree, last_offset, end, GFP_NOFS);
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, last_offset,
PAGE_CACHE_SIZE);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
if (!em || last_offset < em->start ||
(last_offset + PAGE_CACHE_SIZE > extent_map_end(em)) ||
em_tree = &BTRFS_I(inode)->extent_tree;
/* we need the actual starting offset of this extent in the file */
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree,
page_offset(bio->bi_io_vec->bv_page),
PAGE_CACHE_SIZE);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
compressed_len = em->block_len;
cb = kmalloc(compressed_bio_size(root, compressed_len), GFP_NOFS);
int split;
int num_doubles = 0;
+ l = path->nodes[0];
+ slot = path->slots[0];
+ if (extend && data_size + btrfs_item_size_nr(l, slot) +
+ sizeof(struct btrfs_item) > BTRFS_LEAF_DATA_SIZE(root))
+ return -EOVERFLOW;
+
/* first try to make some room by pushing left and right */
if (data_size && ins_key->type != BTRFS_DIR_ITEM_KEY) {
wret = push_leaf_right(trans, root, path, data_size, 0);
*/
#define BTRFS_DEV_ITEMS_OBJECTID 1ULL
+#define BTRFS_BTREE_INODE_OBJECTID 1
+
+#define BTRFS_EMPTY_SUBVOL_DIR_OBJECTID 2
+
/*
* we can actually store much bigger names, but lets not confuse the rest
* of linux
u64 bytes_reserved; /* total bytes the allocator has reserved for
current allocations */
u64 bytes_readonly; /* total bytes that are read only */
-
- /* delalloc accounting */
- u64 bytes_delalloc; /* number of bytes reserved for allocation,
- this space is not necessarily reserved yet
- by the allocator */
+ u64 bytes_super; /* total bytes reserved for the super blocks */
+ u64 bytes_root; /* the number of bytes needed to commit a
+ transaction */
u64 bytes_may_use; /* number of bytes that may be used for
- delalloc */
+ delalloc/allocations */
+ u64 bytes_delalloc; /* number of bytes currently reserved for
+ delayed allocation */
int full; /* indicates that we cannot allocate any more
chunks for this space */
int force_alloc; /* set if we need to force a chunk alloc for
this space */
+ int force_delalloc; /* make people start doing filemap_flush until
+ we're under a threshold */
struct list_head list;
spinlock_t lock;
struct rw_semaphore groups_sem;
atomic_t caching_threads;
+
+ int allocating_chunk;
+ wait_queue_head_t wait;
};
/*
BTRFS_CACHE_FINISHED = 2,
};
+struct btrfs_caching_control {
+ struct list_head list;
+ struct mutex mutex;
+ wait_queue_head_t wait;
+ struct btrfs_block_group_cache *block_group;
+ u64 progress;
+ atomic_t count;
+};
+
struct btrfs_block_group_cache {
struct btrfs_key key;
struct btrfs_block_group_item item;
spinlock_t lock;
u64 pinned;
u64 reserved;
+ u64 bytes_super;
u64 flags;
u64 sectorsize;
int extents_thresh;
int dirty;
/* cache tracking stuff */
- wait_queue_head_t caching_q;
int cached;
+ struct btrfs_caching_control *caching_ctl;
+ u64 last_byte_to_unpin;
struct btrfs_space_info *space_info;
/* the log root tree is a directory of all the other log roots */
struct btrfs_root *log_root_tree;
+
+ spinlock_t fs_roots_radix_lock;
struct radix_tree_root fs_roots_radix;
/* block group cache stuff */
spinlock_t block_group_cache_lock;
struct rb_root block_group_cache_tree;
- struct extent_io_tree pinned_extents;
+ struct extent_io_tree freed_extents[2];
+ struct extent_io_tree *pinned_extents;
/* logical->physical extent mapping */
struct btrfs_mapping_tree mapping_tree;
struct mutex transaction_kthread_mutex;
struct mutex cleaner_mutex;
struct mutex chunk_mutex;
- struct mutex drop_mutex;
struct mutex volume_mutex;
- struct mutex tree_reloc_mutex;
- struct rw_semaphore extent_commit_sem;
-
/*
* this protects the ordered operations list only while we are
* processing all of the entries on it. This way we make
* before jumping into the main commit.
*/
struct mutex ordered_operations_mutex;
+ struct rw_semaphore extent_commit_sem;
+
+ struct rw_semaphore subvol_sem;
+
+ struct srcu_struct subvol_srcu;
struct list_head trans_list;
struct list_head hashers;
struct list_head dead_roots;
+ struct list_head caching_block_groups;
atomic_t nr_async_submits;
atomic_t async_submit_draining;
u32 stripesize;
u32 type;
- u64 highest_inode;
- u64 last_inode_alloc;
+
+ u64 highest_objectid;
int ref_cows;
int track_dirty;
+ int in_radix;
+
u64 defrag_trans_start;
struct btrfs_key defrag_progress;
struct btrfs_key defrag_max;
int btrfs_run_delayed_refs(struct btrfs_trans_handle *trans,
struct btrfs_root *root, unsigned long count);
int btrfs_lookup_extent(struct btrfs_root *root, u64 start, u64 len);
-int btrfs_update_pinned_extents(struct btrfs_root *root,
- u64 bytenr, u64 num, int pin);
+int btrfs_pin_extent(struct btrfs_root *root,
+ u64 bytenr, u64 num, int reserved);
int btrfs_drop_leaf_ref(struct btrfs_trans_handle *trans,
struct btrfs_root *root, struct extent_buffer *leaf);
int btrfs_cross_ref_exist(struct btrfs_trans_handle *trans,
u64 root_objectid, u64 owner, u64 offset);
int btrfs_free_reserved_extent(struct btrfs_root *root, u64 start, u64 len);
+int btrfs_prepare_extent_commit(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root);
int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- struct extent_io_tree *unpin);
+ struct btrfs_root *root);
int btrfs_inc_extent_ref(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
u64 bytenr, u64 num_bytes, u64 parent,
int btrfs_extent_readonly(struct btrfs_root *root, u64 bytenr);
int btrfs_free_block_groups(struct btrfs_fs_info *info);
int btrfs_read_block_groups(struct btrfs_root *root);
+int btrfs_can_relocate(struct btrfs_root *root, u64 bytenr);
int btrfs_make_block_group(struct btrfs_trans_handle *trans,
struct btrfs_root *root, u64 bytes_used,
u64 type, u64 chunk_objectid, u64 chunk_offset,
void btrfs_set_inode_space_info(struct btrfs_root *root, struct inode *ionde);
void btrfs_clear_space_info_full(struct btrfs_fs_info *info);
-int btrfs_check_metadata_free_space(struct btrfs_root *root);
+int btrfs_reserve_metadata_space(struct btrfs_root *root, int num_items);
+int btrfs_unreserve_metadata_space(struct btrfs_root *root, int num_items);
+int btrfs_unreserve_metadata_for_delalloc(struct btrfs_root *root,
+ struct inode *inode, int num_items);
+int btrfs_reserve_metadata_for_delalloc(struct btrfs_root *root,
+ struct inode *inode, int num_items);
int btrfs_check_data_free_space(struct btrfs_root *root, struct inode *inode,
u64 bytes);
void btrfs_free_reserved_data_space(struct btrfs_root *root,
u64 bytes);
void btrfs_delalloc_free_space(struct btrfs_root *root, struct inode *inode,
u64 bytes);
-void btrfs_free_pinned_extents(struct btrfs_fs_info *info);
/* ctree.c */
int btrfs_bin_search(struct extent_buffer *eb, struct btrfs_key *key,
int level, int *slot);
struct extent_buffer *parent);
/* root-item.c */
int btrfs_find_root_ref(struct btrfs_root *tree_root,
- struct btrfs_path *path,
- u64 root_id, u64 ref_id);
+ struct btrfs_path *path,
+ u64 root_id, u64 ref_id);
int btrfs_add_root_ref(struct btrfs_trans_handle *trans,
struct btrfs_root *tree_root,
- u64 root_id, u8 type, u64 ref_id,
- u64 dirid, u64 sequence,
+ u64 root_id, u64 ref_id, u64 dirid, u64 sequence,
+ const char *name, int name_len);
+int btrfs_del_root_ref(struct btrfs_trans_handle *trans,
+ struct btrfs_root *tree_root,
+ u64 root_id, u64 ref_id, u64 dirid, u64 *sequence,
const char *name, int name_len);
int btrfs_del_root(struct btrfs_trans_handle *trans, struct btrfs_root *root,
struct btrfs_key *key);
int btrfs_search_root(struct btrfs_root *root, u64 search_start,
u64 *found_objectid);
int btrfs_find_dead_roots(struct btrfs_root *root, u64 objectid);
+int btrfs_find_orphan_roots(struct btrfs_root *tree_root);
int btrfs_set_root_node(struct btrfs_root_item *item,
struct extent_buffer *node);
/* dir-item.c */
struct btrfs_path *path, u64 dir,
u64 objectid, const char *name, int name_len,
int mod);
+struct btrfs_dir_item *
+btrfs_search_dir_index_item(struct btrfs_root *root,
+ struct btrfs_path *path, u64 dirid,
+ const char *name, int name_len);
struct btrfs_dir_item *btrfs_match_dir_item_name(struct btrfs_root *root,
struct btrfs_path *path,
const char *name, int name_len);
struct btrfs_root *root, u64 offset);
int btrfs_del_orphan_item(struct btrfs_trans_handle *trans,
struct btrfs_root *root, u64 offset);
+int btrfs_find_orphan_item(struct btrfs_root *root, u64 offset);
/* inode-map.c */
int btrfs_find_free_objectid(struct btrfs_trans_handle *trans,
int btrfs_add_link(struct btrfs_trans_handle *trans,
struct inode *parent_inode, struct inode *inode,
const char *name, int name_len, int add_backref, u64 index);
+int btrfs_unlink_subvol(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root,
+ struct inode *dir, u64 objectid,
+ const char *name, int name_len);
int btrfs_truncate_inode_items(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
struct inode *inode, u64 new_size,
int btrfs_writepages(struct address_space *mapping,
struct writeback_control *wbc);
int btrfs_create_subvol_root(struct btrfs_trans_handle *trans,
- struct btrfs_root *new_root, struct dentry *dentry,
+ struct btrfs_root *new_root,
u64 new_dirid, u64 alloc_hint);
int btrfs_merge_bio_hook(struct page *page, unsigned long offset,
size_t size, struct bio *bio, unsigned long bio_flags);
void btrfs_dirty_inode(struct inode *inode);
struct inode *btrfs_alloc_inode(struct super_block *sb);
void btrfs_destroy_inode(struct inode *inode);
+void btrfs_drop_inode(struct inode *inode);
int btrfs_init_cachep(void);
void btrfs_destroy_cachep(void);
long btrfs_ioctl_trans_end(struct file *file);
int btrfs_orphan_del(struct btrfs_trans_handle *trans, struct inode *inode);
void btrfs_orphan_cleanup(struct btrfs_root *root);
int btrfs_cont_expand(struct inode *inode, loff_t size);
+int btrfs_invalidate_inodes(struct btrfs_root *root);
+extern struct dentry_operations btrfs_dentry_operations;
/* ioctl.c */
long btrfs_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
int btrfs_drop_extent_cache(struct inode *inode, u64 start, u64 end,
int skip_pinned);
int btrfs_check_file(struct btrfs_root *root, struct inode *inode);
-extern struct file_operations btrfs_file_operations;
+extern const struct file_operations btrfs_file_operations;
int btrfs_drop_extents(struct btrfs_trans_handle *trans,
struct btrfs_root *root, struct inode *inode,
u64 start, u64 end, u64 locked_end,
- u64 inline_limit, u64 *hint_block);
+ u64 inline_limit, u64 *hint_block, int drop_cache);
int btrfs_mark_extent_written(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
struct inode *inode, u64 start, u64 end);
int btrfs_sync_fs(struct super_block *sb, int wait);
/* acl.c */
-#ifdef CONFIG_FS_POSIX_ACL
+#ifdef CONFIG_BTRFS_POSIX_ACL
int btrfs_check_acl(struct inode *inode, int mask);
#else
#define btrfs_check_acl NULL
return btrfs_match_dir_item_name(root, path, name, name_len);
}
+struct btrfs_dir_item *
+btrfs_search_dir_index_item(struct btrfs_root *root,
+ struct btrfs_path *path, u64 dirid,
+ const char *name, int name_len)
+{
+ struct extent_buffer *leaf;
+ struct btrfs_dir_item *di;
+ struct btrfs_key key;
+ u32 nritems;
+ int ret;
+
+ key.objectid = dirid;
+ key.type = BTRFS_DIR_INDEX_KEY;
+ key.offset = 0;
+
+ ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
+ if (ret < 0)
+ return ERR_PTR(ret);
+
+ leaf = path->nodes[0];
+ nritems = btrfs_header_nritems(leaf);
+
+ while (1) {
+ if (path->slots[0] >= nritems) {
+ ret = btrfs_next_leaf(root, path);
+ if (ret < 0)
+ return ERR_PTR(ret);
+ if (ret > 0)
+ break;
+ leaf = path->nodes[0];
+ nritems = btrfs_header_nritems(leaf);
+ continue;
+ }
+
+ btrfs_item_key_to_cpu(leaf, &key, path->slots[0]);
+ if (key.objectid != dirid || key.type != BTRFS_DIR_INDEX_KEY)
+ break;
+
+ di = btrfs_match_dir_item_name(root, path, name, name_len);
+ if (di)
+ return di;
+
+ path->slots[0]++;
+ }
+ return NULL;
+}
+
struct btrfs_dir_item *btrfs_lookup_xattr(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
struct btrfs_path *path, u64 dir,
static struct extent_io_ops btree_extent_io_ops;
static void end_workqueue_fn(struct btrfs_work *work);
+static void free_fs_root(struct btrfs_root *root);
static atomic_t btrfs_bdi_num = ATOMIC_INIT(0);
struct extent_map *em;
int ret;
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, start, len);
if (em) {
em->bdev =
BTRFS_I(inode)->root->fs_info->fs_devices->latest_bdev;
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
goto out;
}
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
em = alloc_extent_map(GFP_NOFS);
if (!em) {
em->block_start = 0;
em->bdev = BTRFS_I(inode)->root->fs_info->fs_devices->latest_bdev;
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
if (ret == -EEXIST) {
u64 failed_start = em->start;
free_extent_map(em);
em = NULL;
}
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
if (ret)
em = ERR_PTR(ret);
int btrfs_write_tree_block(struct extent_buffer *buf)
{
- return btrfs_fdatawrite_range(buf->first_page->mapping, buf->start,
- buf->start + buf->len - 1, WB_SYNC_ALL);
+ return filemap_fdatawrite_range(buf->first_page->mapping, buf->start,
+ buf->start + buf->len - 1);
}
int btrfs_wait_tree_block_writeback(struct extent_buffer *buf)
{
- return btrfs_wait_on_page_writeback_range(buf->first_page->mapping,
- buf->start, buf->start + buf->len - 1);
+ return filemap_fdatawait_range(buf->first_page->mapping,
+ buf->start, buf->start + buf->len - 1);
}
struct extent_buffer *read_tree_block(struct btrfs_root *root, u64 bytenr,
root->fs_info = fs_info;
root->objectid = objectid;
root->last_trans = 0;
- root->highest_inode = 0;
- root->last_inode_alloc = 0;
+ root->highest_objectid = 0;
root->name = NULL;
root->in_sysfs = 0;
root->inode_tree.rb_node = NULL;
root, fs_info, objectid);
ret = btrfs_find_last_root(tree_root, objectid,
&root->root_item, &root->root_key);
+ if (ret > 0)
+ return -ENOENT;
BUG_ON(ret);
generation = btrfs_root_generation(&root->root_item);
blocksize = btrfs_level_size(root, btrfs_root_level(&root->root_item));
root->node = read_tree_block(root, btrfs_root_bytenr(&root->root_item),
blocksize, generation);
- root->commit_root = btrfs_root_node(root);
BUG_ON(!root->node);
+ root->commit_root = btrfs_root_node(root);
return 0;
}
struct btrfs_fs_info *fs_info = tree_root->fs_info;
struct btrfs_path *path;
struct extent_buffer *l;
- u64 highest_inode;
u64 generation;
u32 blocksize;
int ret = 0;
kfree(root);
return ERR_PTR(ret);
}
- goto insert;
+ goto out;
}
__setup_root(tree_root->nodesize, tree_root->leafsize,
path = btrfs_alloc_path();
BUG_ON(!path);
ret = btrfs_search_slot(NULL, tree_root, location, path, 0, 0);
- if (ret != 0) {
- if (ret > 0)
- ret = -ENOENT;
- goto out;
+ if (ret == 0) {
+ l = path->nodes[0];
+ read_extent_buffer(l, &root->root_item,
+ btrfs_item_ptr_offset(l, path->slots[0]),
+ sizeof(root->root_item));
+ memcpy(&root->root_key, location, sizeof(*location));
}
- l = path->nodes[0];
- read_extent_buffer(l, &root->root_item,
- btrfs_item_ptr_offset(l, path->slots[0]),
- sizeof(root->root_item));
- memcpy(&root->root_key, location, sizeof(*location));
- ret = 0;
-out:
- btrfs_release_path(root, path);
btrfs_free_path(path);
if (ret) {
- kfree(root);
+ if (ret > 0)
+ ret = -ENOENT;
return ERR_PTR(ret);
}
+
generation = btrfs_root_generation(&root->root_item);
blocksize = btrfs_level_size(root, btrfs_root_level(&root->root_item));
root->node = read_tree_block(root, btrfs_root_bytenr(&root->root_item),
blocksize, generation);
root->commit_root = btrfs_root_node(root);
BUG_ON(!root->node);
-insert:
- if (location->objectid != BTRFS_TREE_LOG_OBJECTID) {
+out:
+ if (location->objectid != BTRFS_TREE_LOG_OBJECTID)
root->ref_cows = 1;
- ret = btrfs_find_highest_inode(root, &highest_inode);
- if (ret == 0) {
- root->highest_inode = highest_inode;
- root->last_inode_alloc = highest_inode;
- }
- }
+
return root;
}
return fs_info->dev_root;
if (location->objectid == BTRFS_CSUM_TREE_OBJECTID)
return fs_info->csum_root;
-
+again:
+ spin_lock(&fs_info->fs_roots_radix_lock);
root = radix_tree_lookup(&fs_info->fs_roots_radix,
(unsigned long)location->objectid);
+ spin_unlock(&fs_info->fs_roots_radix_lock);
if (root)
return root;
+ ret = btrfs_find_orphan_item(fs_info->tree_root, location->objectid);
+ if (ret == 0)
+ ret = -ENOENT;
+ if (ret < 0)
+ return ERR_PTR(ret);
+
root = btrfs_read_fs_root_no_radix(fs_info->tree_root, location);
if (IS_ERR(root))
return root;
+ WARN_ON(btrfs_root_refs(&root->root_item) == 0);
set_anon_super(&root->anon_super, NULL);
+ ret = radix_tree_preload(GFP_NOFS & ~__GFP_HIGHMEM);
+ if (ret)
+ goto fail;
+
+ spin_lock(&fs_info->fs_roots_radix_lock);
ret = radix_tree_insert(&fs_info->fs_roots_radix,
(unsigned long)root->root_key.objectid,
root);
+ if (ret == 0)
+ root->in_radix = 1;
+ spin_unlock(&fs_info->fs_roots_radix_lock);
+ radix_tree_preload_end();
if (ret) {
- free_extent_buffer(root->node);
- kfree(root);
- return ERR_PTR(ret);
+ if (ret == -EEXIST) {
+ free_fs_root(root);
+ goto again;
+ }
+ goto fail;
}
- if (!(fs_info->sb->s_flags & MS_RDONLY)) {
- ret = btrfs_find_dead_roots(fs_info->tree_root,
- root->root_key.objectid);
- BUG_ON(ret);
+
+ ret = btrfs_find_dead_roots(fs_info->tree_root,
+ root->root_key.objectid);
+ WARN_ON(ret);
+
+ if (!(fs_info->sb->s_flags & MS_RDONLY))
btrfs_orphan_cleanup(root);
- }
+
return root;
+fail:
+ free_fs_root(root);
+ return ERR_PTR(ret);
}
struct btrfs_root *btrfs_read_fs_root(struct btrfs_fs_info *fs_info,
struct btrfs_key *location,
const char *name, int namelen)
{
+ return btrfs_read_fs_root_no_name(fs_info, location);
+#if 0
struct btrfs_root *root;
int ret;
kfree(root);
return ERR_PTR(ret);
}
-#if 0
+
ret = btrfs_sysfs_add_root(root);
if (ret) {
free_extent_buffer(root->node);
kfree(root);
return ERR_PTR(ret);
}
-#endif
root->in_sysfs = 1;
return root;
+#endif
}
static int btrfs_congested_fn(void *congested_data, int bdi_bits)
offset = page_offset(page);
em_tree = &BTRFS_I(inode)->extent_tree;
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, offset, PAGE_CACHE_SIZE);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
if (!em) {
__unplug_io_fn(bdi, page);
return;
err = bdi_register(bdi, NULL, "btrfs-%d",
atomic_inc_return(&btrfs_bdi_num));
- if (err)
+ if (err) {
+ bdi_destroy(bdi);
return err;
+ }
bdi->ra_pages = default_backing_dev_info.ra_pages;
bdi->unplug_io_fn = btrfs_unplug_io_fn;
break;
vfs_check_frozen(root->fs_info->sb, SB_FREEZE_WRITE);
- mutex_lock(&root->fs_info->cleaner_mutex);
- btrfs_clean_old_snapshots(root);
- mutex_unlock(&root->fs_info->cleaner_mutex);
+
+ if (!(root->fs_info->sb->s_flags & MS_RDONLY) &&
+ mutex_trylock(&root->fs_info->cleaner_mutex)) {
+ btrfs_clean_old_snapshots(root);
+ mutex_unlock(&root->fs_info->cleaner_mutex);
+ }
if (freezing(current)) {
refrigerator();
err = -ENOMEM;
goto fail;
}
- INIT_RADIX_TREE(&fs_info->fs_roots_radix, GFP_NOFS);
+
+ ret = init_srcu_struct(&fs_info->subvol_srcu);
+ if (ret) {
+ err = ret;
+ goto fail;
+ }
+
+ ret = setup_bdi(fs_info, &fs_info->bdi);
+ if (ret) {
+ err = ret;
+ goto fail_srcu;
+ }
+
+ fs_info->btree_inode = new_inode(sb);
+ if (!fs_info->btree_inode) {
+ err = -ENOMEM;
+ goto fail_bdi;
+ }
+
+ INIT_RADIX_TREE(&fs_info->fs_roots_radix, GFP_ATOMIC);
INIT_LIST_HEAD(&fs_info->trans_list);
INIT_LIST_HEAD(&fs_info->dead_roots);
INIT_LIST_HEAD(&fs_info->hashers);
INIT_LIST_HEAD(&fs_info->delalloc_inodes);
INIT_LIST_HEAD(&fs_info->ordered_operations);
+ INIT_LIST_HEAD(&fs_info->caching_block_groups);
spin_lock_init(&fs_info->delalloc_lock);
spin_lock_init(&fs_info->new_trans_lock);
spin_lock_init(&fs_info->ref_cache_lock);
+ spin_lock_init(&fs_info->fs_roots_radix_lock);
init_completion(&fs_info->kobj_unregister);
fs_info->tree_root = tree_root;
fs_info->sb = sb;
fs_info->max_extent = (u64)-1;
fs_info->max_inline = 8192 * 1024;
- if (setup_bdi(fs_info, &fs_info->bdi))
- goto fail_bdi;
- fs_info->btree_inode = new_inode(sb);
- fs_info->btree_inode->i_ino = 1;
- fs_info->btree_inode->i_nlink = 1;
- fs_info->metadata_ratio = 8;
+ fs_info->metadata_ratio = 0;
fs_info->thread_pool_size = min_t(unsigned long,
num_online_cpus() + 2, 8);
sb->s_blocksize_bits = blksize_bits(4096);
sb->s_bdi = &fs_info->bdi;
+ fs_info->btree_inode->i_ino = BTRFS_BTREE_INODE_OBJECTID;
+ fs_info->btree_inode->i_nlink = 1;
/*
* we set the i_size on the btree inode to the max possible int.
* the real end of the address space is determined by all of
BTRFS_I(fs_info->btree_inode)->io_tree.ops = &btree_extent_io_ops;
+ BTRFS_I(fs_info->btree_inode)->root = tree_root;
+ memset(&BTRFS_I(fs_info->btree_inode)->location, 0,
+ sizeof(struct btrfs_key));
+ BTRFS_I(fs_info->btree_inode)->dummy_inode = 1;
+ insert_inode_hash(fs_info->btree_inode);
+
spin_lock_init(&fs_info->block_group_cache_lock);
fs_info->block_group_cache_tree.rb_node = NULL;
- extent_io_tree_init(&fs_info->pinned_extents,
+ extent_io_tree_init(&fs_info->freed_extents[0],
fs_info->btree_inode->i_mapping, GFP_NOFS);
+ extent_io_tree_init(&fs_info->freed_extents[1],
+ fs_info->btree_inode->i_mapping, GFP_NOFS);
+ fs_info->pinned_extents = &fs_info->freed_extents[0];
fs_info->do_barriers = 1;
- BTRFS_I(fs_info->btree_inode)->root = tree_root;
- memset(&BTRFS_I(fs_info->btree_inode)->location, 0,
- sizeof(struct btrfs_key));
- insert_inode_hash(fs_info->btree_inode);
mutex_init(&fs_info->trans_mutex);
mutex_init(&fs_info->ordered_operations_mutex);
mutex_init(&fs_info->tree_log_mutex);
- mutex_init(&fs_info->drop_mutex);
mutex_init(&fs_info->chunk_mutex);
mutex_init(&fs_info->transaction_kthread_mutex);
mutex_init(&fs_info->cleaner_mutex);
mutex_init(&fs_info->volume_mutex);
- mutex_init(&fs_info->tree_reloc_mutex);
init_rwsem(&fs_info->extent_commit_sem);
+ init_rwsem(&fs_info->subvol_sem);
btrfs_init_free_cluster(&fs_info->meta_alloc_cluster);
btrfs_init_free_cluster(&fs_info->data_alloc_cluster);
err = -EINVAL;
goto fail_iput;
}
-
+printk("thread pool is %d\n", fs_info->thread_pool_size);
/*
* we need to start all the end_io workers up front because the
* queue work function gets called at interrupt time, and so it
fs_info->endio_workers.idle_thresh = 4;
fs_info->endio_meta_workers.idle_thresh = 4;
- fs_info->endio_write_workers.idle_thresh = 64;
- fs_info->endio_meta_write_workers.idle_thresh = 64;
+ fs_info->endio_write_workers.idle_thresh = 2;
+ fs_info->endio_meta_write_workers.idle_thresh = 2;
+
+ fs_info->endio_workers.atomic_worker_start = 1;
+ fs_info->endio_meta_workers.atomic_worker_start = 1;
+ fs_info->endio_write_workers.atomic_worker_start = 1;
+ fs_info->endio_meta_write_workers.atomic_worker_start = 1;
btrfs_start_workers(&fs_info->workers, 1);
btrfs_start_workers(&fs_info->submit_workers, 1);
btrfs_start_workers(&fs_info->delalloc_workers, 1);
btrfs_start_workers(&fs_info->fixup_workers, 1);
- btrfs_start_workers(&fs_info->endio_workers, fs_info->thread_pool_size);
- btrfs_start_workers(&fs_info->endio_meta_workers,
- fs_info->thread_pool_size);
- btrfs_start_workers(&fs_info->endio_meta_write_workers,
- fs_info->thread_pool_size);
- btrfs_start_workers(&fs_info->endio_write_workers,
- fs_info->thread_pool_size);
+ btrfs_start_workers(&fs_info->endio_workers, 1);
+ btrfs_start_workers(&fs_info->endio_meta_workers, 1);
+ btrfs_start_workers(&fs_info->endio_meta_write_workers, 1);
+ btrfs_start_workers(&fs_info->endio_write_workers, 1);
fs_info->bdi.ra_pages *= btrfs_super_num_devices(disk_super);
fs_info->bdi.ra_pages = max(fs_info->bdi.ra_pages,
}
}
+ ret = btrfs_find_orphan_roots(tree_root);
+ BUG_ON(ret);
+
if (!(sb->s_flags & MS_RDONLY)) {
ret = btrfs_recover_relocation(tree_root);
BUG_ON(ret);
btrfs_mapping_tree_free(&fs_info->mapping_tree);
fail_bdi:
bdi_destroy(&fs_info->bdi);
+fail_srcu:
+ cleanup_srcu_struct(&fs_info->subvol_srcu);
fail:
kfree(extent_root);
kfree(tree_root);
int btrfs_free_fs_root(struct btrfs_fs_info *fs_info, struct btrfs_root *root)
{
- WARN_ON(!RB_EMPTY_ROOT(&root->inode_tree));
+ spin_lock(&fs_info->fs_roots_radix_lock);
radix_tree_delete(&fs_info->fs_roots_radix,
(unsigned long)root->root_key.objectid);
+ spin_unlock(&fs_info->fs_roots_radix_lock);
+
+ if (btrfs_root_refs(&root->root_item) == 0)
+ synchronize_srcu(&fs_info->subvol_srcu);
+
+ free_fs_root(root);
+ return 0;
+}
+
+static void free_fs_root(struct btrfs_root *root)
+{
+ WARN_ON(!RB_EMPTY_ROOT(&root->inode_tree));
if (root->anon_super.s_dev) {
down_write(&root->anon_super.s_umount);
kill_anon_super(&root->anon_super);
}
- if (root->node)
- free_extent_buffer(root->node);
- if (root->commit_root)
- free_extent_buffer(root->commit_root);
+ free_extent_buffer(root->node);
+ free_extent_buffer(root->commit_root);
kfree(root->name);
kfree(root);
- return 0;
}
static int del_fs_roots(struct btrfs_fs_info *fs_info)
struct btrfs_root *gang[8];
int i;
+ while (!list_empty(&fs_info->dead_roots)) {
+ gang[0] = list_entry(fs_info->dead_roots.next,
+ struct btrfs_root, root_list);
+ list_del(&gang[0]->root_list);
+
+ if (gang[0]->in_radix) {
+ btrfs_free_fs_root(fs_info, gang[0]);
+ } else {
+ free_extent_buffer(gang[0]->node);
+ free_extent_buffer(gang[0]->commit_root);
+ kfree(gang[0]);
+ }
+ }
+
while (1) {
ret = radix_tree_gang_lookup(&fs_info->fs_roots_radix,
(void **)gang, 0,
root_objectid = gang[ret - 1]->root_key.objectid + 1;
for (i = 0; i < ret; i++) {
root_objectid = gang[i]->root_key.objectid;
- ret = btrfs_find_dead_roots(fs_info->tree_root,
- root_objectid);
- BUG_ON(ret);
btrfs_orphan_cleanup(gang[i]);
}
root_objectid++;
free_extent_buffer(root->fs_info->csum_root->commit_root);
btrfs_free_block_groups(root->fs_info);
- btrfs_free_pinned_extents(root->fs_info);
del_fs_roots(fs_info);
btrfs_mapping_tree_free(&fs_info->mapping_tree);
bdi_destroy(&fs_info->bdi);
+ cleanup_srcu_struct(&fs_info->subvol_srcu);
kfree(fs_info->extent_root);
kfree(fs_info->tree_root);
len = BTRFS_FID_SIZE_NON_CONNECTABLE;
type = FILEID_BTRFS_WITHOUT_PARENT;
- fid->objectid = BTRFS_I(inode)->location.objectid;
+ fid->objectid = inode->i_ino;
fid->root_objectid = BTRFS_I(inode)->root->objectid;
fid->gen = inode->i_generation;
}
static struct dentry *btrfs_get_dentry(struct super_block *sb, u64 objectid,
- u64 root_objectid, u32 generation)
+ u64 root_objectid, u32 generation,
+ int check_generation)
{
+ struct btrfs_fs_info *fs_info = btrfs_sb(sb)->fs_info;
struct btrfs_root *root;
+ struct dentry *dentry;
struct inode *inode;
struct btrfs_key key;
+ int index;
+ int err = 0;
+
+ if (objectid < BTRFS_FIRST_FREE_OBJECTID)
+ return ERR_PTR(-ESTALE);
key.objectid = root_objectid;
btrfs_set_key_type(&key, BTRFS_ROOT_ITEM_KEY);
key.offset = (u64)-1;
- root = btrfs_read_fs_root_no_name(btrfs_sb(sb)->fs_info, &key);
- if (IS_ERR(root))
- return ERR_CAST(root);
+ index = srcu_read_lock(&fs_info->subvol_srcu);
+
+ root = btrfs_read_fs_root_no_name(fs_info, &key);
+ if (IS_ERR(root)) {
+ err = PTR_ERR(root);
+ goto fail;
+ }
+
+ if (btrfs_root_refs(&root->root_item) == 0) {
+ err = -ENOENT;
+ goto fail;
+ }
key.objectid = objectid;
btrfs_set_key_type(&key, BTRFS_INODE_ITEM_KEY);
key.offset = 0;
inode = btrfs_iget(sb, &key, root);
- if (IS_ERR(inode))
- return (void *)inode;
+ if (IS_ERR(inode)) {
+ err = PTR_ERR(inode);
+ goto fail;
+ }
+
+ srcu_read_unlock(&fs_info->subvol_srcu, index);
- if (generation != inode->i_generation) {
+ if (check_generation && generation != inode->i_generation) {
iput(inode);
return ERR_PTR(-ESTALE);
}
- return d_obtain_alias(inode);
+ dentry = d_obtain_alias(inode);
+ if (!IS_ERR(dentry))
+ dentry->d_op = &btrfs_dentry_operations;
+ return dentry;
+fail:
+ srcu_read_unlock(&fs_info->subvol_srcu, index);
+ return ERR_PTR(err);
}
static struct dentry *btrfs_fh_to_parent(struct super_block *sb, struct fid *fh,
objectid = fid->parent_objectid;
generation = fid->parent_gen;
- return btrfs_get_dentry(sb, objectid, root_objectid, generation);
+ return btrfs_get_dentry(sb, objectid, root_objectid, generation, 1);
}
static struct dentry *btrfs_fh_to_dentry(struct super_block *sb, struct fid *fh,
root_objectid = fid->root_objectid;
generation = fid->gen;
- return btrfs_get_dentry(sb, objectid, root_objectid, generation);
+ return btrfs_get_dentry(sb, objectid, root_objectid, generation, 1);
}
static struct dentry *btrfs_get_parent(struct dentry *child)
{
struct inode *dir = child->d_inode;
+ static struct dentry *dentry;
struct btrfs_root *root = BTRFS_I(dir)->root;
- struct btrfs_key key;
struct btrfs_path *path;
struct extent_buffer *leaf;
- int slot;
- u64 objectid;
+ struct btrfs_root_ref *ref;
+ struct btrfs_key key;
+ struct btrfs_key found_key;
int ret;
path = btrfs_alloc_path();
- key.objectid = dir->i_ino;
- btrfs_set_key_type(&key, BTRFS_INODE_REF_KEY);
- key.offset = (u64)-1;
+ if (dir->i_ino == BTRFS_FIRST_FREE_OBJECTID) {
+ key.objectid = root->root_key.objectid;
+ key.type = BTRFS_ROOT_BACKREF_KEY;
+ key.offset = (u64)-1;
+ root = root->fs_info->tree_root;
+ } else {
+ key.objectid = dir->i_ino;
+ key.type = BTRFS_INODE_REF_KEY;
+ key.offset = (u64)-1;
+ }
ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
- if (ret < 0) {
- /* Error */
- btrfs_free_path(path);
- return ERR_PTR(ret);
+ if (ret < 0)
+ goto fail;
+
+ BUG_ON(ret == 0);
+ if (path->slots[0] == 0) {
+ ret = -ENOENT;
+ goto fail;
}
+
+ path->slots[0]--;
leaf = path->nodes[0];
- slot = path->slots[0];
- if (ret) {
- /* btrfs_search_slot() returns the slot where we'd want to
- insert a backref for parent inode #0xFFFFFFFFFFFFFFFF.
- The _real_ backref, telling us what the parent inode
- _actually_ is, will be in the slot _before_ the one
- that btrfs_search_slot() returns. */
- if (!slot) {
- /* Unless there is _no_ key in the tree before... */
- btrfs_free_path(path);
- return ERR_PTR(-EIO);
- }
- slot--;
+
+ btrfs_item_key_to_cpu(leaf, &found_key, path->slots[0]);
+ if (found_key.objectid != key.objectid || found_key.type != key.type) {
+ ret = -ENOENT;
+ goto fail;
}
- btrfs_item_key_to_cpu(leaf, &key, slot);
+ if (found_key.type == BTRFS_ROOT_BACKREF_KEY) {
+ ref = btrfs_item_ptr(leaf, path->slots[0],
+ struct btrfs_root_ref);
+ key.objectid = btrfs_root_ref_dirid(leaf, ref);
+ } else {
+ key.objectid = found_key.offset;
+ }
btrfs_free_path(path);
- if (key.objectid != dir->i_ino || key.type != BTRFS_INODE_REF_KEY)
- return ERR_PTR(-EINVAL);
-
- objectid = key.offset;
-
- /* If we are already at the root of a subvol, return the real root */
- if (objectid == dir->i_ino)
- return dget(dir->i_sb->s_root);
+ if (found_key.type == BTRFS_ROOT_BACKREF_KEY) {
+ return btrfs_get_dentry(root->fs_info->sb, key.objectid,
+ found_key.offset, 0, 0);
+ }
- /* Build a new key for the inode item */
- key.objectid = objectid;
- btrfs_set_key_type(&key, BTRFS_INODE_ITEM_KEY);
+ key.type = BTRFS_INODE_ITEM_KEY;
key.offset = 0;
-
- return d_obtain_alias(btrfs_iget(root->fs_info->sb, &key, root));
+ dentry = d_obtain_alias(btrfs_iget(root->fs_info->sb, &key, root));
+ if (!IS_ERR(dentry))
+ dentry->d_op = &btrfs_dentry_operations;
+ return dentry;
+fail:
+ btrfs_free_path(path);
+ return ERR_PTR(ret);
}
const struct export_operations btrfs_export_ops = {
#include "locking.h"
#include "free-space-cache.h"
-static int update_reserved_extents(struct btrfs_root *root,
- u64 bytenr, u64 num, int reserve);
static int update_block_group(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
u64 bytenr, u64 num_bytes, int alloc,
int mark_free);
+static int update_reserved_extents(struct btrfs_block_group_cache *cache,
+ u64 num_bytes, int reserve);
static int __btrfs_free_extent(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
u64 bytenr, u64 num_bytes, u64 parent,
u64 parent, u64 root_objectid,
u64 flags, struct btrfs_disk_key *key,
int level, struct btrfs_key *ins);
-
static int do_chunk_alloc(struct btrfs_trans_handle *trans,
struct btrfs_root *extent_root, u64 alloc_bytes,
u64 flags, int force);
+static int pin_down_bytes(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root,
+ struct btrfs_path *path,
+ u64 bytenr, u64 num_bytes,
+ int is_data, int reserved,
+ struct extent_buffer **must_clean);
+static int find_next_key(struct btrfs_path *path, int level,
+ struct btrfs_key *key);
+static void dump_space_info(struct btrfs_space_info *info, u64 bytes,
+ int dump_block_groups);
static noinline int
block_group_cache_done(struct btrfs_block_group_cache *cache)
return ret;
}
-/*
- * We always set EXTENT_LOCKED for the super mirror extents so we don't
- * overwrite them, so those bits need to be unset. Also, if we are unmounting
- * with pinned extents still sitting there because we had a block group caching,
- * we need to clear those now, since we are done.
- */
-void btrfs_free_pinned_extents(struct btrfs_fs_info *info)
+static int add_excluded_extent(struct btrfs_root *root,
+ u64 start, u64 num_bytes)
{
- u64 start, end, last = 0;
- int ret;
+ u64 end = start + num_bytes - 1;
+ set_extent_bits(&root->fs_info->freed_extents[0],
+ start, end, EXTENT_UPTODATE, GFP_NOFS);
+ set_extent_bits(&root->fs_info->freed_extents[1],
+ start, end, EXTENT_UPTODATE, GFP_NOFS);
+ return 0;
+}
- while (1) {
- ret = find_first_extent_bit(&info->pinned_extents, last,
- &start, &end,
- EXTENT_LOCKED|EXTENT_DIRTY);
- if (ret)
- break;
+static void free_excluded_extents(struct btrfs_root *root,
+ struct btrfs_block_group_cache *cache)
+{
+ u64 start, end;
- clear_extent_bits(&info->pinned_extents, start, end,
- EXTENT_LOCKED|EXTENT_DIRTY, GFP_NOFS);
- last = end+1;
- }
+ start = cache->key.objectid;
+ end = start + cache->key.offset - 1;
+
+ clear_extent_bits(&root->fs_info->freed_extents[0],
+ start, end, EXTENT_UPTODATE, GFP_NOFS);
+ clear_extent_bits(&root->fs_info->freed_extents[1],
+ start, end, EXTENT_UPTODATE, GFP_NOFS);
}
-static int remove_sb_from_cache(struct btrfs_root *root,
- struct btrfs_block_group_cache *cache)
+static int exclude_super_stripes(struct btrfs_root *root,
+ struct btrfs_block_group_cache *cache)
{
- struct btrfs_fs_info *fs_info = root->fs_info;
u64 bytenr;
u64 *logical;
int stripe_len;
cache->key.objectid, bytenr,
0, &logical, &nr, &stripe_len);
BUG_ON(ret);
+
while (nr--) {
- try_lock_extent(&fs_info->pinned_extents,
- logical[nr],
- logical[nr] + stripe_len - 1, GFP_NOFS);
+ cache->bytes_super += stripe_len;
+ ret = add_excluded_extent(root, logical[nr],
+ stripe_len);
+ BUG_ON(ret);
}
+
kfree(logical);
}
-
return 0;
}
+static struct btrfs_caching_control *
+get_caching_control(struct btrfs_block_group_cache *cache)
+{
+ struct btrfs_caching_control *ctl;
+
+ spin_lock(&cache->lock);
+ if (cache->cached != BTRFS_CACHE_STARTED) {
+ spin_unlock(&cache->lock);
+ return NULL;
+ }
+
+ ctl = cache->caching_ctl;
+ atomic_inc(&ctl->count);
+ spin_unlock(&cache->lock);
+ return ctl;
+}
+
+static void put_caching_control(struct btrfs_caching_control *ctl)
+{
+ if (atomic_dec_and_test(&ctl->count))
+ kfree(ctl);
+}
+
/*
* this is only called by cache_block_group, since we could have freed extents
* we need to check the pinned_extents for any extents that can't be used yet
int ret;
while (start < end) {
- ret = find_first_extent_bit(&info->pinned_extents, start,
+ ret = find_first_extent_bit(info->pinned_extents, start,
&extent_start, &extent_end,
- EXTENT_DIRTY|EXTENT_LOCKED);
+ EXTENT_DIRTY | EXTENT_UPTODATE);
if (ret)
break;
{
struct btrfs_block_group_cache *block_group = data;
struct btrfs_fs_info *fs_info = block_group->fs_info;
- u64 last = 0;
+ struct btrfs_caching_control *caching_ctl = block_group->caching_ctl;
+ struct btrfs_root *extent_root = fs_info->extent_root;
struct btrfs_path *path;
- int ret = 0;
- struct btrfs_key key;
struct extent_buffer *leaf;
- int slot;
+ struct btrfs_key key;
u64 total_found = 0;
-
- BUG_ON(!fs_info);
+ u64 last = 0;
+ u32 nritems;
+ int ret = 0;
path = btrfs_alloc_path();
if (!path)
return -ENOMEM;
- atomic_inc(&block_group->space_info->caching_threads);
+ exclude_super_stripes(extent_root, block_group);
+ spin_lock(&block_group->space_info->lock);
+ block_group->space_info->bytes_super += block_group->bytes_super;
+ spin_unlock(&block_group->space_info->lock);
+
last = max_t(u64, block_group->key.objectid, BTRFS_SUPER_INFO_OFFSET);
+
/*
* We don't want to deadlock with somebody trying to allocate a new
* extent for the extent root while also trying to search the extent
key.objectid = last;
key.offset = 0;
- btrfs_set_key_type(&key, BTRFS_EXTENT_ITEM_KEY);
+ key.type = BTRFS_EXTENT_ITEM_KEY;
again:
+ mutex_lock(&caching_ctl->mutex);
/* need to make sure the commit_root doesn't disappear */
down_read(&fs_info->extent_commit_sem);
- ret = btrfs_search_slot(NULL, fs_info->extent_root, &key, path, 0, 0);
+ ret = btrfs_search_slot(NULL, extent_root, &key, path, 0, 0);
if (ret < 0)
goto err;
+ leaf = path->nodes[0];
+ nritems = btrfs_header_nritems(leaf);
+
while (1) {
smp_mb();
- if (block_group->fs_info->closing > 1) {
+ if (fs_info->closing > 1) {
last = (u64)-1;
break;
}
- leaf = path->nodes[0];
- slot = path->slots[0];
- if (slot >= btrfs_header_nritems(leaf)) {
- ret = btrfs_next_leaf(fs_info->extent_root, path);
- if (ret < 0)
- goto err;
- else if (ret)
+ if (path->slots[0] < nritems) {
+ btrfs_item_key_to_cpu(leaf, &key, path->slots[0]);
+ } else {
+ ret = find_next_key(path, 0, &key);
+ if (ret)
break;
- if (need_resched() ||
- btrfs_transaction_in_commit(fs_info)) {
- leaf = path->nodes[0];
-
- /* this shouldn't happen, but if the
- * leaf is empty just move on.
- */
- if (btrfs_header_nritems(leaf) == 0)
- break;
- /*
- * we need to copy the key out so that
- * we are sure the next search advances
- * us forward in the btree.
- */
- btrfs_item_key_to_cpu(leaf, &key, 0);
- btrfs_release_path(fs_info->extent_root, path);
- up_read(&fs_info->extent_commit_sem);
+ caching_ctl->progress = last;
+ btrfs_release_path(extent_root, path);
+ up_read(&fs_info->extent_commit_sem);
+ mutex_unlock(&caching_ctl->mutex);
+ if (btrfs_transaction_in_commit(fs_info))
schedule_timeout(1);
- goto again;
- }
+ else
+ cond_resched();
+ goto again;
+ }
+ if (key.objectid < block_group->key.objectid) {
+ path->slots[0]++;
continue;
}
- btrfs_item_key_to_cpu(leaf, &key, slot);
- if (key.objectid < block_group->key.objectid)
- goto next;
if (key.objectid >= block_group->key.objectid +
block_group->key.offset)
break;
- if (btrfs_key_type(&key) == BTRFS_EXTENT_ITEM_KEY) {
+ if (key.type == BTRFS_EXTENT_ITEM_KEY) {
total_found += add_new_free_space(block_group,
fs_info, last,
key.objectid);
last = key.objectid + key.offset;
- }
- if (total_found > (1024 * 1024 * 2)) {
- total_found = 0;
- wake_up(&block_group->caching_q);
+ if (total_found > (1024 * 1024 * 2)) {
+ total_found = 0;
+ wake_up(&caching_ctl->wait);
+ }
}
-next:
path->slots[0]++;
}
ret = 0;
total_found += add_new_free_space(block_group, fs_info, last,
block_group->key.objectid +
block_group->key.offset);
+ caching_ctl->progress = (u64)-1;
spin_lock(&block_group->lock);
+ block_group->caching_ctl = NULL;
block_group->cached = BTRFS_CACHE_FINISHED;
spin_unlock(&block_group->lock);
err:
btrfs_free_path(path);
up_read(&fs_info->extent_commit_sem);
- atomic_dec(&block_group->space_info->caching_threads);
- wake_up(&block_group->caching_q);
+ free_excluded_extents(extent_root, block_group);
+
+ mutex_unlock(&caching_ctl->mutex);
+ wake_up(&caching_ctl->wait);
+
+ put_caching_control(caching_ctl);
+ atomic_dec(&block_group->space_info->caching_threads);
return 0;
}
static int cache_block_group(struct btrfs_block_group_cache *cache)
{
+ struct btrfs_fs_info *fs_info = cache->fs_info;
+ struct btrfs_caching_control *caching_ctl;
struct task_struct *tsk;
int ret = 0;
+ smp_mb();
+ if (cache->cached != BTRFS_CACHE_NO)
+ return 0;
+
+ caching_ctl = kzalloc(sizeof(*caching_ctl), GFP_KERNEL);
+ BUG_ON(!caching_ctl);
+
+ INIT_LIST_HEAD(&caching_ctl->list);
+ mutex_init(&caching_ctl->mutex);
+ init_waitqueue_head(&caching_ctl->wait);
+ caching_ctl->block_group = cache;
+ caching_ctl->progress = cache->key.objectid;
+ /* one for caching kthread, one for caching block group list */
+ atomic_set(&caching_ctl->count, 2);
+
spin_lock(&cache->lock);
if (cache->cached != BTRFS_CACHE_NO) {
spin_unlock(&cache->lock);
- return ret;
+ kfree(caching_ctl);
+ return 0;
}
+ cache->caching_ctl = caching_ctl;
cache->cached = BTRFS_CACHE_STARTED;
spin_unlock(&cache->lock);
+ down_write(&fs_info->extent_commit_sem);
+ list_add_tail(&caching_ctl->list, &fs_info->caching_block_groups);
+ up_write(&fs_info->extent_commit_sem);
+
+ atomic_inc(&cache->space_info->caching_threads);
+
tsk = kthread_run(caching_kthread, cache, "btrfs-cache-%llu\n",
cache->key.objectid);
if (IS_ERR(tsk)) {
parent, ref_root, flags,
ref->objectid, ref->offset,
&ins, node->ref_mod);
- update_reserved_extents(root, ins.objectid, ins.offset, 0);
} else if (node->action == BTRFS_ADD_DELAYED_REF) {
ret = __btrfs_inc_extent_ref(trans, root, node->bytenr,
node->num_bytes, parent,
extent_op->flags_to_set,
&extent_op->key,
ref->level, &ins);
- update_reserved_extents(root, ins.objectid, ins.offset, 0);
} else if (node->action == BTRFS_ADD_DELAYED_REF) {
ret = __btrfs_inc_extent_ref(trans, root, node->bytenr,
node->num_bytes, parent, ref_root,
BUG_ON(extent_op);
head = btrfs_delayed_node_to_head(node);
if (insert_reserved) {
+ int mark_free = 0;
+ struct extent_buffer *must_clean = NULL;
+
+ ret = pin_down_bytes(trans, root, NULL,
+ node->bytenr, node->num_bytes,
+ head->is_data, 1, &must_clean);
+ if (ret > 0)
+ mark_free = 1;
+
+ if (must_clean) {
+ clean_tree_block(NULL, root, must_clean);
+ btrfs_tree_unlock(must_clean);
+ free_extent_buffer(must_clean);
+ }
if (head->is_data) {
ret = btrfs_del_csums(trans, root,
node->bytenr,
node->num_bytes);
BUG_ON(ret);
}
- btrfs_update_pinned_extents(root, node->bytenr,
- node->num_bytes, 1);
- update_reserved_extents(root, node->bytenr,
- node->num_bytes, 0);
+ if (mark_free) {
+ ret = btrfs_free_reserved_extent(root,
+ node->bytenr,
+ node->num_bytes);
+ BUG_ON(ret);
+ }
}
mutex_unlock(&head->mutex);
return 0;
alloc_target);
}
+static u64 calculate_bytes_needed(struct btrfs_root *root, int num_items)
+{
+ u64 num_bytes;
+ int level;
+
+ level = BTRFS_MAX_LEVEL - 2;
+ /*
+ * NOTE: these calculations are absolutely the worst possible case.
+ * This assumes that _every_ item we insert will require a new leaf, and
+ * that the tree has grown to its maximum level size.
+ */
+
+ /*
+ * for every item we insert we could insert both an extent item and a
+ * extent ref item. Then for ever item we insert, we will need to cow
+ * both the original leaf, plus the leaf to the left and right of it.
+ *
+ * Unless we are talking about the extent root, then we just want the
+ * number of items * 2, since we just need the extent item plus its ref.
+ */
+ if (root == root->fs_info->extent_root)
+ num_bytes = num_items * 2;
+ else
+ num_bytes = (num_items + (2 * num_items)) * 3;
+
+ /*
+ * num_bytes is total number of leaves we could need times the leaf
+ * size, and then for every leaf we could end up cow'ing 2 nodes per
+ * level, down to the leaf level.
+ */
+ num_bytes = (num_bytes * root->leafsize) +
+ (num_bytes * (level * 2)) * root->nodesize;
+
+ return num_bytes;
+}
+
/*
- * for now this just makes sure we have at least 5% of our metadata space free
- * for use.
+ * Unreserve metadata space for delalloc. If we have less reserved credits than
+ * we have extents, this function does nothing.
*/
-int btrfs_check_metadata_free_space(struct btrfs_root *root)
+int btrfs_unreserve_metadata_for_delalloc(struct btrfs_root *root,
+ struct inode *inode, int num_items)
{
struct btrfs_fs_info *info = root->fs_info;
struct btrfs_space_info *meta_sinfo;
- u64 alloc_target, thresh;
- int committed = 0, ret;
+ u64 num_bytes;
+ u64 alloc_target;
+ bool bug = false;
/* get the space info for where the metadata will live */
alloc_target = btrfs_get_alloc_profile(root, 0);
meta_sinfo = __find_space_info(info, alloc_target);
-again:
- spin_lock(&meta_sinfo->lock);
- if (!meta_sinfo->full)
- thresh = meta_sinfo->total_bytes * 80;
- else
- thresh = meta_sinfo->total_bytes * 95;
-
- do_div(thresh, 100);
-
- if (meta_sinfo->bytes_used + meta_sinfo->bytes_reserved +
- meta_sinfo->bytes_pinned + meta_sinfo->bytes_readonly > thresh) {
- struct btrfs_trans_handle *trans;
- if (!meta_sinfo->full) {
- meta_sinfo->force_alloc = 1;
- spin_unlock(&meta_sinfo->lock);
-
- trans = btrfs_start_transaction(root, 1);
- if (!trans)
- return -ENOMEM;
+ num_bytes = calculate_bytes_needed(root->fs_info->extent_root,
+ num_items);
- ret = do_chunk_alloc(trans, root->fs_info->extent_root,
- 2 * 1024 * 1024, alloc_target, 0);
- btrfs_end_transaction(trans, root);
- goto again;
- }
+ spin_lock(&meta_sinfo->lock);
+ if (BTRFS_I(inode)->delalloc_reserved_extents <=
+ BTRFS_I(inode)->delalloc_extents) {
spin_unlock(&meta_sinfo->lock);
+ return 0;
+ }
- if (!committed) {
- committed = 1;
- trans = btrfs_join_transaction(root, 1);
- if (!trans)
- return -ENOMEM;
- ret = btrfs_commit_transaction(trans, root);
- if (ret)
- return ret;
- goto again;
- }
- return -ENOSPC;
+ BTRFS_I(inode)->delalloc_reserved_extents--;
+ BUG_ON(BTRFS_I(inode)->delalloc_reserved_extents < 0);
+
+ if (meta_sinfo->bytes_delalloc < num_bytes) {
+ bug = true;
+ meta_sinfo->bytes_delalloc = 0;
+ } else {
+ meta_sinfo->bytes_delalloc -= num_bytes;
}
spin_unlock(&meta_sinfo->lock);
+ BUG_ON(bug);
+
return 0;
}
-/*
- * This will check the space that the inode allocates from to make sure we have
- * enough space for bytes.
- */
-int btrfs_check_data_free_space(struct btrfs_root *root, struct inode *inode,
- u64 bytes)
+static void check_force_delalloc(struct btrfs_space_info *meta_sinfo)
{
- struct btrfs_space_info *data_sinfo;
- int ret = 0, committed = 0;
+ u64 thresh;
- /* make sure bytes are sectorsize aligned */
- bytes = (bytes + root->sectorsize - 1) & ~((u64)root->sectorsize - 1);
+ thresh = meta_sinfo->bytes_used + meta_sinfo->bytes_reserved +
+ meta_sinfo->bytes_pinned + meta_sinfo->bytes_readonly +
+ meta_sinfo->bytes_super + meta_sinfo->bytes_root +
+ meta_sinfo->bytes_may_use;
- data_sinfo = BTRFS_I(inode)->space_info;
-again:
- /* make sure we have enough space to handle the data first */
- spin_lock(&data_sinfo->lock);
- if (data_sinfo->total_bytes - data_sinfo->bytes_used -
- data_sinfo->bytes_delalloc - data_sinfo->bytes_reserved -
- data_sinfo->bytes_pinned - data_sinfo->bytes_readonly -
- data_sinfo->bytes_may_use < bytes) {
- struct btrfs_trans_handle *trans;
+ thresh = meta_sinfo->total_bytes - thresh;
+ thresh *= 80;
+ do_div(thresh, 100);
+ if (thresh <= meta_sinfo->bytes_delalloc)
+ meta_sinfo->force_delalloc = 1;
+ else
+ meta_sinfo->force_delalloc = 0;
+}
- /*
- * if we don't have enough free bytes in this space then we need
- * to alloc a new chunk.
- */
- if (!data_sinfo->full) {
- u64 alloc_target;
+static int maybe_allocate_chunk(struct btrfs_root *root,
+ struct btrfs_space_info *info)
+{
+ struct btrfs_super_block *disk_super = &root->fs_info->super_copy;
+ struct btrfs_trans_handle *trans;
+ bool wait = false;
+ int ret = 0;
+ u64 min_metadata;
+ u64 free_space;
- data_sinfo->force_alloc = 1;
- spin_unlock(&data_sinfo->lock);
+ free_space = btrfs_super_total_bytes(disk_super);
+ /*
+ * we allow the metadata to grow to a max of either 5gb or 5% of the
+ * space in the volume.
+ */
+ min_metadata = min((u64)5 * 1024 * 1024 * 1024,
+ div64_u64(free_space * 5, 100));
+ if (info->total_bytes >= min_metadata) {
+ spin_unlock(&info->lock);
+ return 0;
+ }
- alloc_target = btrfs_get_alloc_profile(root, 1);
- trans = btrfs_start_transaction(root, 1);
- if (!trans)
- return -ENOMEM;
+ if (info->full) {
+ spin_unlock(&info->lock);
+ return 0;
+ }
- ret = do_chunk_alloc(trans, root->fs_info->extent_root,
- bytes + 2 * 1024 * 1024,
- alloc_target, 0);
- btrfs_end_transaction(trans, root);
- if (ret)
- return ret;
- goto again;
- }
- spin_unlock(&data_sinfo->lock);
+ if (!info->allocating_chunk) {
+ info->force_alloc = 1;
+ info->allocating_chunk = 1;
+ init_waitqueue_head(&info->wait);
+ } else {
+ wait = true;
+ }
- /* commit the current transaction and try again */
- if (!committed) {
- committed = 1;
- trans = btrfs_join_transaction(root, 1);
- if (!trans)
- return -ENOMEM;
- ret = btrfs_commit_transaction(trans, root);
- if (ret)
- return ret;
- goto again;
- }
+ spin_unlock(&info->lock);
- printk(KERN_ERR "no space left, need %llu, %llu delalloc bytes"
- ", %llu bytes_used, %llu bytes_reserved, "
- "%llu bytes_pinned, %llu bytes_readonly, %llu may use "
- "%llu total\n", (unsigned long long)bytes,
- (unsigned long long)data_sinfo->bytes_delalloc,
- (unsigned long long)data_sinfo->bytes_used,
- (unsigned long long)data_sinfo->bytes_reserved,
- (unsigned long long)data_sinfo->bytes_pinned,
- (unsigned long long)data_sinfo->bytes_readonly,
- (unsigned long long)data_sinfo->bytes_may_use,
- (unsigned long long)data_sinfo->total_bytes);
- return -ENOSPC;
+ if (wait) {
+ wait_event(info->wait,
+ !info->allocating_chunk);
+ return 1;
}
- data_sinfo->bytes_may_use += bytes;
- BTRFS_I(inode)->reserved_bytes += bytes;
- spin_unlock(&data_sinfo->lock);
- return btrfs_check_metadata_free_space(root);
+ trans = btrfs_start_transaction(root, 1);
+ if (!trans) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ ret = do_chunk_alloc(trans, root->fs_info->extent_root,
+ 4096 + 2 * 1024 * 1024,
+ info->flags, 0);
+ btrfs_end_transaction(trans, root);
+ if (ret)
+ goto out;
+out:
+ spin_lock(&info->lock);
+ info->allocating_chunk = 0;
+ spin_unlock(&info->lock);
+ wake_up(&info->wait);
+
+ if (ret)
+ return 0;
+ return 1;
}
/*
- * if there was an error for whatever reason after calling
- * btrfs_check_data_free_space, call this so we can cleanup the counters.
+ * Reserve metadata space for delalloc.
*/
-void btrfs_free_reserved_data_space(struct btrfs_root *root,
- struct inode *inode, u64 bytes)
+int btrfs_reserve_metadata_for_delalloc(struct btrfs_root *root,
+ struct inode *inode, int num_items)
{
- struct btrfs_space_info *data_sinfo;
+ struct btrfs_fs_info *info = root->fs_info;
+ struct btrfs_space_info *meta_sinfo;
+ u64 num_bytes;
+ u64 used;
+ u64 alloc_target;
+ int flushed = 0;
+ int force_delalloc;
- /* make sure bytes are sectorsize aligned */
- bytes = (bytes + root->sectorsize - 1) & ~((u64)root->sectorsize - 1);
+ /* get the space info for where the metadata will live */
+ alloc_target = btrfs_get_alloc_profile(root, 0);
+ meta_sinfo = __find_space_info(info, alloc_target);
+
+ num_bytes = calculate_bytes_needed(root->fs_info->extent_root,
+ num_items);
+again:
+ spin_lock(&meta_sinfo->lock);
+
+ force_delalloc = meta_sinfo->force_delalloc;
+
+ if (unlikely(!meta_sinfo->bytes_root))
+ meta_sinfo->bytes_root = calculate_bytes_needed(root, 6);
+
+ if (!flushed)
+ meta_sinfo->bytes_delalloc += num_bytes;
+
+ used = meta_sinfo->bytes_used + meta_sinfo->bytes_reserved +
+ meta_sinfo->bytes_pinned + meta_sinfo->bytes_readonly +
+ meta_sinfo->bytes_super + meta_sinfo->bytes_root +
+ meta_sinfo->bytes_may_use + meta_sinfo->bytes_delalloc;
+
+ if (used > meta_sinfo->total_bytes) {
+ flushed++;
+
+ if (flushed == 1) {
+ if (maybe_allocate_chunk(root, meta_sinfo))
+ goto again;
+ flushed++;
+ } else {
+ spin_unlock(&meta_sinfo->lock);
+ }
+
+ if (flushed == 2) {
+ filemap_flush(inode->i_mapping);
+ goto again;
+ } else if (flushed == 3) {
+ btrfs_start_delalloc_inodes(root);
+ btrfs_wait_ordered_extents(root, 0);
+ goto again;
+ }
+ spin_lock(&meta_sinfo->lock);
+ meta_sinfo->bytes_delalloc -= num_bytes;
+ spin_unlock(&meta_sinfo->lock);
+ printk(KERN_ERR "enospc, has %d, reserved %d\n",
+ BTRFS_I(inode)->delalloc_extents,
+ BTRFS_I(inode)->delalloc_reserved_extents);
+ dump_space_info(meta_sinfo, 0, 0);
+ return -ENOSPC;
+ }
+
+ BTRFS_I(inode)->delalloc_reserved_extents++;
+ check_force_delalloc(meta_sinfo);
+ spin_unlock(&meta_sinfo->lock);
+
+ if (!flushed && force_delalloc)
+ filemap_flush(inode->i_mapping);
+
+ return 0;
+}
+
+/*
+ * unreserve num_items number of items worth of metadata space. This needs to
+ * be paired with btrfs_reserve_metadata_space.
+ *
+ * NOTE: if you have the option, run this _AFTER_ you do a
+ * btrfs_end_transaction, since btrfs_end_transaction will run delayed ref
+ * oprations which will result in more used metadata, so we want to make sure we
+ * can do that without issue.
+ */
+int btrfs_unreserve_metadata_space(struct btrfs_root *root, int num_items)
+{
+ struct btrfs_fs_info *info = root->fs_info;
+ struct btrfs_space_info *meta_sinfo;
+ u64 num_bytes;
+ u64 alloc_target;
+ bool bug = false;
+
+ /* get the space info for where the metadata will live */
+ alloc_target = btrfs_get_alloc_profile(root, 0);
+ meta_sinfo = __find_space_info(info, alloc_target);
+
+ num_bytes = calculate_bytes_needed(root, num_items);
+
+ spin_lock(&meta_sinfo->lock);
+ if (meta_sinfo->bytes_may_use < num_bytes) {
+ bug = true;
+ meta_sinfo->bytes_may_use = 0;
+ } else {
+ meta_sinfo->bytes_may_use -= num_bytes;
+ }
+ spin_unlock(&meta_sinfo->lock);
+
+ BUG_ON(bug);
+
+ return 0;
+}
+
+/*
+ * Reserve some metadata space for use. We'll calculate the worste case number
+ * of bytes that would be needed to modify num_items number of items. If we
+ * have space, fantastic, if not, you get -ENOSPC. Please call
+ * btrfs_unreserve_metadata_space when you are done for the _SAME_ number of
+ * items you reserved, since whatever metadata you needed should have already
+ * been allocated.
+ *
+ * This will commit the transaction to make more space if we don't have enough
+ * metadata space. THe only time we don't do this is if we're reserving space
+ * inside of a transaction, then we will just return -ENOSPC and it is the
+ * callers responsibility to handle it properly.
+ */
+int btrfs_reserve_metadata_space(struct btrfs_root *root, int num_items)
+{
+ struct btrfs_fs_info *info = root->fs_info;
+ struct btrfs_space_info *meta_sinfo;
+ u64 num_bytes;
+ u64 used;
+ u64 alloc_target;
+ int retries = 0;
+
+ /* get the space info for where the metadata will live */
+ alloc_target = btrfs_get_alloc_profile(root, 0);
+ meta_sinfo = __find_space_info(info, alloc_target);
+
+ num_bytes = calculate_bytes_needed(root, num_items);
+again:
+ spin_lock(&meta_sinfo->lock);
+
+ if (unlikely(!meta_sinfo->bytes_root))
+ meta_sinfo->bytes_root = calculate_bytes_needed(root, 6);
+
+ if (!retries)
+ meta_sinfo->bytes_may_use += num_bytes;
+
+ used = meta_sinfo->bytes_used + meta_sinfo->bytes_reserved +
+ meta_sinfo->bytes_pinned + meta_sinfo->bytes_readonly +
+ meta_sinfo->bytes_super + meta_sinfo->bytes_root +
+ meta_sinfo->bytes_may_use + meta_sinfo->bytes_delalloc;
+
+ if (used > meta_sinfo->total_bytes) {
+ retries++;
+ if (retries == 1) {
+ if (maybe_allocate_chunk(root, meta_sinfo))
+ goto again;
+ retries++;
+ } else {
+ spin_unlock(&meta_sinfo->lock);
+ }
+
+ if (retries == 2) {
+ btrfs_start_delalloc_inodes(root);
+ btrfs_wait_ordered_extents(root, 0);
+ goto again;
+ }
+ spin_lock(&meta_sinfo->lock);
+ meta_sinfo->bytes_may_use -= num_bytes;
+ spin_unlock(&meta_sinfo->lock);
+
+ dump_space_info(meta_sinfo, 0, 0);
+ return -ENOSPC;
+ }
+
+ check_force_delalloc(meta_sinfo);
+ spin_unlock(&meta_sinfo->lock);
+
+ return 0;
+}
+
+/*
+ * This will check the space that the inode allocates from to make sure we have
+ * enough space for bytes.
+ */
+int btrfs_check_data_free_space(struct btrfs_root *root, struct inode *inode,
+ u64 bytes)
+{
+ struct btrfs_space_info *data_sinfo;
+ int ret = 0, committed = 0;
+
+ /* make sure bytes are sectorsize aligned */
+ bytes = (bytes + root->sectorsize - 1) & ~((u64)root->sectorsize - 1);
+
+ data_sinfo = BTRFS_I(inode)->space_info;
+ if (!data_sinfo)
+ goto alloc;
+
+again:
+ /* make sure we have enough space to handle the data first */
+ spin_lock(&data_sinfo->lock);
+ if (data_sinfo->total_bytes - data_sinfo->bytes_used -
+ data_sinfo->bytes_delalloc - data_sinfo->bytes_reserved -
+ data_sinfo->bytes_pinned - data_sinfo->bytes_readonly -
+ data_sinfo->bytes_may_use - data_sinfo->bytes_super < bytes) {
+ struct btrfs_trans_handle *trans;
+
+ /*
+ * if we don't have enough free bytes in this space then we need
+ * to alloc a new chunk.
+ */
+ if (!data_sinfo->full) {
+ u64 alloc_target;
+
+ data_sinfo->force_alloc = 1;
+ spin_unlock(&data_sinfo->lock);
+alloc:
+ alloc_target = btrfs_get_alloc_profile(root, 1);
+ trans = btrfs_start_transaction(root, 1);
+ if (!trans)
+ return -ENOMEM;
+
+ ret = do_chunk_alloc(trans, root->fs_info->extent_root,
+ bytes + 2 * 1024 * 1024,
+ alloc_target, 0);
+ btrfs_end_transaction(trans, root);
+ if (ret)
+ return ret;
+
+ if (!data_sinfo) {
+ btrfs_set_inode_space_info(root, inode);
+ data_sinfo = BTRFS_I(inode)->space_info;
+ }
+ goto again;
+ }
+ spin_unlock(&data_sinfo->lock);
+
+ /* commit the current transaction and try again */
+ if (!committed && !root->fs_info->open_ioctl_trans) {
+ committed = 1;
+ trans = btrfs_join_transaction(root, 1);
+ if (!trans)
+ return -ENOMEM;
+ ret = btrfs_commit_transaction(trans, root);
+ if (ret)
+ return ret;
+ goto again;
+ }
+
+ printk(KERN_ERR "no space left, need %llu, %llu delalloc bytes"
+ ", %llu bytes_used, %llu bytes_reserved, "
+ "%llu bytes_pinned, %llu bytes_readonly, %llu may use "
+ "%llu total\n", (unsigned long long)bytes,
+ (unsigned long long)data_sinfo->bytes_delalloc,
+ (unsigned long long)data_sinfo->bytes_used,
+ (unsigned long long)data_sinfo->bytes_reserved,
+ (unsigned long long)data_sinfo->bytes_pinned,
+ (unsigned long long)data_sinfo->bytes_readonly,
+ (unsigned long long)data_sinfo->bytes_may_use,
+ (unsigned long long)data_sinfo->total_bytes);
+ return -ENOSPC;
+ }
+ data_sinfo->bytes_may_use += bytes;
+ BTRFS_I(inode)->reserved_bytes += bytes;
+ spin_unlock(&data_sinfo->lock);
+
+ return 0;
+}
+
+/*
+ * if there was an error for whatever reason after calling
+ * btrfs_check_data_free_space, call this so we can cleanup the counters.
+ */
+void btrfs_free_reserved_data_space(struct btrfs_root *root,
+ struct inode *inode, u64 bytes)
+{
+ struct btrfs_space_info *data_sinfo;
+
+ /* make sure bytes are sectorsize aligned */
+ bytes = (bytes + root->sectorsize - 1) & ~((u64)root->sectorsize - 1);
data_sinfo = BTRFS_I(inode)->space_info;
spin_lock(&data_sinfo->lock);
BUG_ON(!space_info);
spin_lock(&space_info->lock);
- if (space_info->force_alloc) {
+ if (space_info->force_alloc)
force = 1;
- space_info->force_alloc = 0;
- }
if (space_info->full) {
spin_unlock(&space_info->lock);
goto out;
}
thresh = space_info->total_bytes - space_info->bytes_readonly;
- thresh = div_factor(thresh, 6);
+ thresh = div_factor(thresh, 8);
if (!force &&
(space_info->bytes_used + space_info->bytes_pinned +
space_info->bytes_reserved + alloc_bytes) < thresh) {
* we keep a reasonable number of metadata chunks allocated in the
* FS as well.
*/
- if (flags & BTRFS_BLOCK_GROUP_DATA) {
+ if (flags & BTRFS_BLOCK_GROUP_DATA && fs_info->metadata_ratio) {
fs_info->data_chunk_allocations++;
if (!(fs_info->data_chunk_allocations %
fs_info->metadata_ratio))
}
ret = btrfs_alloc_chunk(trans, extent_root, flags);
+ spin_lock(&space_info->lock);
if (ret)
space_info->full = 1;
+ space_info->force_alloc = 0;
+ spin_unlock(&space_info->lock);
out:
mutex_unlock(&extent_root->fs_info->chunk_mutex);
return ret;
num_bytes = min(total, cache->key.offset - byte_in_group);
if (alloc) {
old_val += num_bytes;
+ btrfs_set_block_group_used(&cache->item, old_val);
+ cache->reserved -= num_bytes;
cache->space_info->bytes_used += num_bytes;
+ cache->space_info->bytes_reserved -= num_bytes;
if (cache->ro)
cache->space_info->bytes_readonly -= num_bytes;
- btrfs_set_block_group_used(&cache->item, old_val);
spin_unlock(&cache->lock);
spin_unlock(&cache->space_info->lock);
} else {
return bytenr;
}
-int btrfs_update_pinned_extents(struct btrfs_root *root,
- u64 bytenr, u64 num, int pin)
+/*
+ * this function must be called within transaction
+ */
+int btrfs_pin_extent(struct btrfs_root *root,
+ u64 bytenr, u64 num_bytes, int reserved)
{
- u64 len;
- struct btrfs_block_group_cache *cache;
struct btrfs_fs_info *fs_info = root->fs_info;
+ struct btrfs_block_group_cache *cache;
- if (pin)
- set_extent_dirty(&fs_info->pinned_extents,
- bytenr, bytenr + num - 1, GFP_NOFS);
-
- while (num > 0) {
- cache = btrfs_lookup_block_group(fs_info, bytenr);
- BUG_ON(!cache);
- len = min(num, cache->key.offset -
- (bytenr - cache->key.objectid));
- if (pin) {
- spin_lock(&cache->space_info->lock);
- spin_lock(&cache->lock);
- cache->pinned += len;
- cache->space_info->bytes_pinned += len;
- spin_unlock(&cache->lock);
- spin_unlock(&cache->space_info->lock);
- fs_info->total_pinned += len;
- } else {
- int unpin = 0;
+ cache = btrfs_lookup_block_group(fs_info, bytenr);
+ BUG_ON(!cache);
- /*
- * in order to not race with the block group caching, we
- * only want to unpin the extent if we are cached. If
- * we aren't cached, we want to start async caching this
- * block group so we can free the extent the next time
- * around.
- */
- spin_lock(&cache->space_info->lock);
- spin_lock(&cache->lock);
- unpin = (cache->cached == BTRFS_CACHE_FINISHED);
- if (likely(unpin)) {
- cache->pinned -= len;
- cache->space_info->bytes_pinned -= len;
- fs_info->total_pinned -= len;
- }
- spin_unlock(&cache->lock);
- spin_unlock(&cache->space_info->lock);
+ spin_lock(&cache->space_info->lock);
+ spin_lock(&cache->lock);
+ cache->pinned += num_bytes;
+ cache->space_info->bytes_pinned += num_bytes;
+ if (reserved) {
+ cache->reserved -= num_bytes;
+ cache->space_info->bytes_reserved -= num_bytes;
+ }
+ spin_unlock(&cache->lock);
+ spin_unlock(&cache->space_info->lock);
- if (likely(unpin))
- clear_extent_dirty(&fs_info->pinned_extents,
- bytenr, bytenr + len -1,
- GFP_NOFS);
- else
- cache_block_group(cache);
+ btrfs_put_block_group(cache);
- if (unpin)
- btrfs_add_free_space(cache, bytenr, len);
- }
- btrfs_put_block_group(cache);
- bytenr += len;
- num -= len;
+ set_extent_dirty(fs_info->pinned_extents,
+ bytenr, bytenr + num_bytes - 1, GFP_NOFS);
+ return 0;
+}
+
+static int update_reserved_extents(struct btrfs_block_group_cache *cache,
+ u64 num_bytes, int reserve)
+{
+ spin_lock(&cache->space_info->lock);
+ spin_lock(&cache->lock);
+ if (reserve) {
+ cache->reserved += num_bytes;
+ cache->space_info->bytes_reserved += num_bytes;
+ } else {
+ cache->reserved -= num_bytes;
+ cache->space_info->bytes_reserved -= num_bytes;
}
+ spin_unlock(&cache->lock);
+ spin_unlock(&cache->space_info->lock);
return 0;
}
-static int update_reserved_extents(struct btrfs_root *root,
- u64 bytenr, u64 num, int reserve)
+int btrfs_prepare_extent_commit(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root)
{
- u64 len;
- struct btrfs_block_group_cache *cache;
struct btrfs_fs_info *fs_info = root->fs_info;
+ struct btrfs_caching_control *next;
+ struct btrfs_caching_control *caching_ctl;
+ struct btrfs_block_group_cache *cache;
- while (num > 0) {
- cache = btrfs_lookup_block_group(fs_info, bytenr);
- BUG_ON(!cache);
- len = min(num, cache->key.offset -
- (bytenr - cache->key.objectid));
+ down_write(&fs_info->extent_commit_sem);
- spin_lock(&cache->space_info->lock);
- spin_lock(&cache->lock);
- if (reserve) {
- cache->reserved += len;
- cache->space_info->bytes_reserved += len;
+ list_for_each_entry_safe(caching_ctl, next,
+ &fs_info->caching_block_groups, list) {
+ cache = caching_ctl->block_group;
+ if (block_group_cache_done(cache)) {
+ cache->last_byte_to_unpin = (u64)-1;
+ list_del_init(&caching_ctl->list);
+ put_caching_control(caching_ctl);
} else {
- cache->reserved -= len;
- cache->space_info->bytes_reserved -= len;
+ cache->last_byte_to_unpin = caching_ctl->progress;
}
- spin_unlock(&cache->lock);
- spin_unlock(&cache->space_info->lock);
- btrfs_put_block_group(cache);
- bytenr += len;
- num -= len;
}
+
+ if (fs_info->pinned_extents == &fs_info->freed_extents[0])
+ fs_info->pinned_extents = &fs_info->freed_extents[1];
+ else
+ fs_info->pinned_extents = &fs_info->freed_extents[0];
+
+ up_write(&fs_info->extent_commit_sem);
return 0;
}
-int btrfs_copy_pinned(struct btrfs_root *root, struct extent_io_tree *copy)
+static int unpin_extent_range(struct btrfs_root *root, u64 start, u64 end)
{
- u64 last = 0;
- u64 start;
- u64 end;
- struct extent_io_tree *pinned_extents = &root->fs_info->pinned_extents;
- int ret;
+ struct btrfs_fs_info *fs_info = root->fs_info;
+ struct btrfs_block_group_cache *cache = NULL;
+ u64 len;
- while (1) {
- ret = find_first_extent_bit(pinned_extents, last,
- &start, &end, EXTENT_DIRTY);
- if (ret)
- break;
+ while (start <= end) {
+ if (!cache ||
+ start >= cache->key.objectid + cache->key.offset) {
+ if (cache)
+ btrfs_put_block_group(cache);
+ cache = btrfs_lookup_block_group(fs_info, start);
+ BUG_ON(!cache);
+ }
+
+ len = cache->key.objectid + cache->key.offset - start;
+ len = min(len, end + 1 - start);
- set_extent_dirty(copy, start, end, GFP_NOFS);
- last = end + 1;
+ if (start < cache->last_byte_to_unpin) {
+ len = min(len, cache->last_byte_to_unpin - start);
+ btrfs_add_free_space(cache, start, len);
+ }
+
+ spin_lock(&cache->space_info->lock);
+ spin_lock(&cache->lock);
+ cache->pinned -= len;
+ cache->space_info->bytes_pinned -= len;
+ spin_unlock(&cache->lock);
+ spin_unlock(&cache->space_info->lock);
+
+ start += len;
}
+
+ if (cache)
+ btrfs_put_block_group(cache);
return 0;
}
int btrfs_finish_extent_commit(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- struct extent_io_tree *unpin)
+ struct btrfs_root *root)
{
+ struct btrfs_fs_info *fs_info = root->fs_info;
+ struct extent_io_tree *unpin;
u64 start;
u64 end;
int ret;
+ if (fs_info->pinned_extents == &fs_info->freed_extents[0])
+ unpin = &fs_info->freed_extents[1];
+ else
+ unpin = &fs_info->freed_extents[0];
+
while (1) {
ret = find_first_extent_bit(unpin, 0, &start, &end,
EXTENT_DIRTY);
ret = btrfs_discard_extent(root, start, end + 1 - start);
- /* unlocks the pinned mutex */
- btrfs_update_pinned_extents(root, start, end + 1 - start, 0);
clear_extent_dirty(unpin, start, end, GFP_NOFS);
-
+ unpin_extent_range(root, start, end);
cond_resched();
}
static int pin_down_bytes(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
struct btrfs_path *path,
- u64 bytenr, u64 num_bytes, int is_data,
+ u64 bytenr, u64 num_bytes,
+ int is_data, int reserved,
struct extent_buffer **must_clean)
{
int err = 0;
}
free_extent_buffer(buf);
pinit:
- btrfs_set_path_blocking(path);
+ if (path)
+ btrfs_set_path_blocking(path);
/* unlocks the pinned mutex */
- btrfs_update_pinned_extents(root, bytenr, num_bytes, 1);
+ btrfs_pin_extent(root, bytenr, num_bytes, reserved);
BUG_ON(err < 0);
return 0;
}
-
static int __btrfs_free_extent(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
u64 bytenr, u64 num_bytes, u64 parent,
}
ret = pin_down_bytes(trans, root, path, bytenr,
- num_bytes, is_data, &must_clean);
+ num_bytes, is_data, 0, &must_clean);
if (ret > 0)
mark_free = 1;
BUG_ON(ret < 0);
if (root_objectid == BTRFS_TREE_LOG_OBJECTID) {
WARN_ON(owner >= BTRFS_FIRST_FREE_OBJECTID);
/* unlocks the pinned mutex */
- btrfs_update_pinned_extents(root, bytenr, num_bytes, 1);
- update_reserved_extents(root, bytenr, num_bytes, 0);
+ btrfs_pin_extent(root, bytenr, num_bytes, 1);
ret = 0;
} else if (owner < BTRFS_FIRST_FREE_OBJECTID) {
ret = btrfs_add_delayed_tree_ref(trans, bytenr, num_bytes,
wait_block_group_cache_progress(struct btrfs_block_group_cache *cache,
u64 num_bytes)
{
+ struct btrfs_caching_control *caching_ctl;
DEFINE_WAIT(wait);
- prepare_to_wait(&cache->caching_q, &wait, TASK_UNINTERRUPTIBLE);
-
- if (block_group_cache_done(cache)) {
- finish_wait(&cache->caching_q, &wait);
+ caching_ctl = get_caching_control(cache);
+ if (!caching_ctl)
return 0;
- }
- schedule();
- finish_wait(&cache->caching_q, &wait);
- wait_event(cache->caching_q, block_group_cache_done(cache) ||
+ wait_event(caching_ctl->wait, block_group_cache_done(cache) ||
(cache->free_space >= num_bytes));
+
+ put_caching_control(caching_ctl);
+ return 0;
+}
+
+static noinline int
+wait_block_group_cache_done(struct btrfs_block_group_cache *cache)
+{
+ struct btrfs_caching_control *caching_ctl;
+ DEFINE_WAIT(wait);
+
+ caching_ctl = get_caching_control(cache);
+ if (!caching_ctl)
+ return 0;
+
+ wait_event(caching_ctl->wait, block_group_cache_done(cache));
+
+ put_caching_control(caching_ctl);
return 0;
}
int last_ptr_loop = 0;
int loop = 0;
bool found_uncached_bg = false;
+ bool failed_cluster_refill = false;
WARN_ON(num_bytes < root->sectorsize);
btrfs_set_key_type(ins, BTRFS_EXTENT_ITEM_KEY);
if (unlikely(block_group->ro))
goto loop;
- if (last_ptr) {
+ /*
+ * Ok we want to try and use the cluster allocator, so lets look
+ * there, unless we are on LOOP_NO_EMPTY_SIZE, since we will
+ * have tried the cluster allocator plenty of times at this
+ * point and not have found anything, so we are likely way too
+ * fragmented for the clustering stuff to find anything, so lets
+ * just skip it and let the allocator find whatever block it can
+ * find
+ */
+ if (last_ptr && loop < LOOP_NO_EMPTY_SIZE) {
/*
* the refill lock keeps out other
* people trying to start a new cluster
spin_unlock(&last_ptr->refill_lock);
goto checks;
}
- } else if (!cached && loop > LOOP_CACHING_NOWAIT) {
+ } else if (!cached && loop > LOOP_CACHING_NOWAIT
+ && !failed_cluster_refill) {
spin_unlock(&last_ptr->refill_lock);
+ failed_cluster_refill = true;
wait_block_group_cache_progress(block_group,
num_bytes + empty_cluster + empty_size);
goto have_block_group;
* cluster. Free the cluster we've been trying
* to use, and go to the next block group
*/
- if (loop < LOOP_NO_EMPTY_SIZE) {
- btrfs_return_cluster_to_free_space(NULL,
- last_ptr);
- spin_unlock(&last_ptr->refill_lock);
- goto loop;
- }
+ btrfs_return_cluster_to_free_space(NULL, last_ptr);
spin_unlock(&last_ptr->refill_lock);
+ goto loop;
}
offset = btrfs_find_space_for_alloc(block_group, search_start,
search_start - offset);
BUG_ON(offset > search_start);
+ update_reserved_extents(block_group, num_bytes, 1);
+
/* we are all good, lets return */
break;
loop:
+ failed_cluster_refill = false;
btrfs_put_block_group(block_group);
}
up_read(&space_info->groups_sem);
return ret;
}
-static void dump_space_info(struct btrfs_space_info *info, u64 bytes)
+static void dump_space_info(struct btrfs_space_info *info, u64 bytes,
+ int dump_block_groups)
{
struct btrfs_block_group_cache *cache;
+ spin_lock(&info->lock);
printk(KERN_INFO "space_info has %llu free, is %sfull\n",
(unsigned long long)(info->total_bytes - info->bytes_used -
- info->bytes_pinned - info->bytes_reserved),
+ info->bytes_pinned - info->bytes_reserved -
+ info->bytes_super),
(info->full) ? "" : "not ");
printk(KERN_INFO "space_info total=%llu, pinned=%llu, delalloc=%llu,"
- " may_use=%llu, used=%llu\n",
+ " may_use=%llu, used=%llu, root=%llu, super=%llu, reserved=%llu"
+ "\n",
(unsigned long long)info->total_bytes,
(unsigned long long)info->bytes_pinned,
(unsigned long long)info->bytes_delalloc,
(unsigned long long)info->bytes_may_use,
- (unsigned long long)info->bytes_used);
+ (unsigned long long)info->bytes_used,
+ (unsigned long long)info->bytes_root,
+ (unsigned long long)info->bytes_super,
+ (unsigned long long)info->bytes_reserved);
+ spin_unlock(&info->lock);
+
+ if (!dump_block_groups)
+ return;
down_read(&info->groups_sem);
list_for_each_entry(cache, &info->block_groups, list) {
up_read(&info->groups_sem);
}
-static int __btrfs_reserve_extent(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- u64 num_bytes, u64 min_alloc_size,
- u64 empty_size, u64 hint_byte,
- u64 search_end, struct btrfs_key *ins,
- u64 data)
+int btrfs_reserve_extent(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root,
+ u64 num_bytes, u64 min_alloc_size,
+ u64 empty_size, u64 hint_byte,
+ u64 search_end, struct btrfs_key *ins,
+ u64 data)
{
int ret;
u64 search_start = 0;
printk(KERN_ERR "btrfs allocation failed flags %llu, "
"wanted %llu\n", (unsigned long long)data,
(unsigned long long)num_bytes);
- dump_space_info(sinfo, num_bytes);
+ dump_space_info(sinfo, num_bytes, 1);
}
return ret;
ret = btrfs_discard_extent(root, start, len);
btrfs_add_free_space(cache, start, len);
+ update_reserved_extents(cache, len, 0);
btrfs_put_block_group(cache);
- update_reserved_extents(root, start, len, 0);
-
- return ret;
-}
-
-int btrfs_reserve_extent(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- u64 num_bytes, u64 min_alloc_size,
- u64 empty_size, u64 hint_byte,
- u64 search_end, struct btrfs_key *ins,
- u64 data)
-{
- int ret;
- ret = __btrfs_reserve_extent(trans, root, num_bytes, min_alloc_size,
- empty_size, hint_byte, search_end, ins,
- data);
- if (!ret)
- update_reserved_extents(root, ins->objectid, ins->offset, 1);
return ret;
}
{
int ret;
struct btrfs_block_group_cache *block_group;
+ struct btrfs_caching_control *caching_ctl;
+ u64 start = ins->objectid;
+ u64 num_bytes = ins->offset;
block_group = btrfs_lookup_block_group(root->fs_info, ins->objectid);
cache_block_group(block_group);
- wait_event(block_group->caching_q,
- block_group_cache_done(block_group));
+ caching_ctl = get_caching_control(block_group);
- ret = btrfs_remove_free_space(block_group, ins->objectid,
- ins->offset);
- BUG_ON(ret);
+ if (!caching_ctl) {
+ BUG_ON(!block_group_cache_done(block_group));
+ ret = btrfs_remove_free_space(block_group, start, num_bytes);
+ BUG_ON(ret);
+ } else {
+ mutex_lock(&caching_ctl->mutex);
+
+ if (start >= caching_ctl->progress) {
+ ret = add_excluded_extent(root, start, num_bytes);
+ BUG_ON(ret);
+ } else if (start + num_bytes <= caching_ctl->progress) {
+ ret = btrfs_remove_free_space(block_group,
+ start, num_bytes);
+ BUG_ON(ret);
+ } else {
+ num_bytes = caching_ctl->progress - start;
+ ret = btrfs_remove_free_space(block_group,
+ start, num_bytes);
+ BUG_ON(ret);
+
+ start = caching_ctl->progress;
+ num_bytes = ins->objectid + ins->offset -
+ caching_ctl->progress;
+ ret = add_excluded_extent(root, start, num_bytes);
+ BUG_ON(ret);
+ }
+
+ mutex_unlock(&caching_ctl->mutex);
+ put_caching_control(caching_ctl);
+ }
+
+ update_reserved_extents(block_group, ins->offset, 1);
btrfs_put_block_group(block_group);
ret = alloc_reserved_file_extent(trans, root, 0, root_objectid,
0, owner, offset, ins, 1);
int ret;
u64 flags = 0;
- ret = __btrfs_reserve_extent(trans, root, num_bytes, num_bytes,
- empty_size, hint_byte, search_end,
- ins, 0);
+ ret = btrfs_reserve_extent(trans, root, num_bytes, num_bytes,
+ empty_size, hint_byte, search_end,
+ ins, 0);
if (ret)
return ret;
} else
BUG_ON(parent > 0);
- update_reserved_extents(root, ins->objectid, ins->offset, 1);
if (root_objectid != BTRFS_TREE_LOG_OBJECTID) {
struct btrfs_delayed_extent_op *extent_op;
extent_op = kmalloc(sizeof(*extent_op), GFP_NOFS);
return buf;
}
-#if 0
-int btrfs_drop_leaf_ref(struct btrfs_trans_handle *trans,
- struct btrfs_root *root, struct extent_buffer *leaf)
-{
- u64 disk_bytenr;
- u64 num_bytes;
- struct btrfs_key key;
- struct btrfs_file_extent_item *fi;
- u32 nritems;
- int i;
- int ret;
-
- BUG_ON(!btrfs_is_leaf(leaf));
- nritems = btrfs_header_nritems(leaf);
-
- for (i = 0; i < nritems; i++) {
- cond_resched();
- btrfs_item_key_to_cpu(leaf, &key, i);
-
- /* only extents have references, skip everything else */
- if (btrfs_key_type(&key) != BTRFS_EXTENT_DATA_KEY)
- continue;
-
- fi = btrfs_item_ptr(leaf, i, struct btrfs_file_extent_item);
-
- /* inline extents live in the btree, they don't have refs */
- if (btrfs_file_extent_type(leaf, fi) ==
- BTRFS_FILE_EXTENT_INLINE)
- continue;
-
- disk_bytenr = btrfs_file_extent_disk_bytenr(leaf, fi);
-
- /* holes don't have refs */
- if (disk_bytenr == 0)
- continue;
-
- num_bytes = btrfs_file_extent_disk_num_bytes(leaf, fi);
- ret = btrfs_free_extent(trans, root, disk_bytenr, num_bytes,
- leaf->start, 0, key.objectid, 0);
- BUG_ON(ret);
- }
- return 0;
-}
-
-static noinline int cache_drop_leaf_ref(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- struct btrfs_leaf_ref *ref)
-{
- int i;
- int ret;
- struct btrfs_extent_info *info;
- struct refsort *sorted;
-
- if (ref->nritems == 0)
- return 0;
-
- sorted = kmalloc(sizeof(*sorted) * ref->nritems, GFP_NOFS);
- for (i = 0; i < ref->nritems; i++) {
- sorted[i].bytenr = ref->extents[i].bytenr;
- sorted[i].slot = i;
- }
- sort(sorted, ref->nritems, sizeof(struct refsort), refsort_cmp, NULL);
-
- /*
- * the items in the ref were sorted when the ref was inserted
- * into the ref cache, so this is already in order
- */
- for (i = 0; i < ref->nritems; i++) {
- info = ref->extents + sorted[i].slot;
- ret = btrfs_free_extent(trans, root, info->bytenr,
- info->num_bytes, ref->bytenr,
- ref->owner, ref->generation,
- info->objectid, 0);
-
- atomic_inc(&root->fs_info->throttle_gen);
- wake_up(&root->fs_info->transaction_throttle);
- cond_resched();
-
- BUG_ON(ret);
- info++;
- }
-
- kfree(sorted);
- return 0;
-}
-
-
-static int drop_snap_lookup_refcount(struct btrfs_trans_handle *trans,
- struct btrfs_root *root, u64 start,
- u64 len, u32 *refs)
-{
- int ret;
-
- ret = btrfs_lookup_extent_refs(trans, root, start, len, refs);
- BUG_ON(ret);
-
-#if 0 /* some debugging code in case we see problems here */
- /* if the refs count is one, it won't get increased again. But
- * if the ref count is > 1, someone may be decreasing it at
- * the same time we are.
- */
- if (*refs != 1) {
- struct extent_buffer *eb = NULL;
- eb = btrfs_find_create_tree_block(root, start, len);
- if (eb)
- btrfs_tree_lock(eb);
-
- mutex_lock(&root->fs_info->alloc_mutex);
- ret = lookup_extent_ref(NULL, root, start, len, refs);
- BUG_ON(ret);
- mutex_unlock(&root->fs_info->alloc_mutex);
-
- if (eb) {
- btrfs_tree_unlock(eb);
- free_extent_buffer(eb);
- }
- if (*refs == 1) {
- printk(KERN_ERR "btrfs block %llu went down to one "
- "during drop_snap\n", (unsigned long long)start);
- }
-
- }
-#endif
-
- cond_resched();
- return ret;
-}
+struct walk_control {
+ u64 refs[BTRFS_MAX_LEVEL];
+ u64 flags[BTRFS_MAX_LEVEL];
+ struct btrfs_key update_progress;
+ int stage;
+ int level;
+ int shared_level;
+ int update_ref;
+ int keep_locks;
+ int reada_slot;
+ int reada_count;
+};
+#define DROP_REFERENCE 1
+#define UPDATE_BACKREF 2
-/*
- * this is used while deleting old snapshots, and it drops the refs
- * on a whole subtree starting from a level 1 node.
- *
- * The idea is to sort all the leaf pointers, and then drop the
- * ref on all the leaves in order. Most of the time the leaves
- * will have ref cache entries, so no leaf IOs will be required to
- * find the extents they have references on.
- *
- * For each leaf, any references it has are also dropped in order
- *
- * This ends up dropping the references in something close to optimal
- * order for reading and modifying the extent allocation tree.
- */
-static noinline int drop_level_one_refs(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- struct btrfs_path *path)
+static noinline void reada_walk_down(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root,
+ struct walk_control *wc,
+ struct btrfs_path *path)
{
u64 bytenr;
- u64 root_owner;
- u64 root_gen;
- struct extent_buffer *eb = path->nodes[1];
- struct extent_buffer *leaf;
- struct btrfs_leaf_ref *ref;
- struct refsort *sorted = NULL;
- int nritems = btrfs_header_nritems(eb);
+ u64 generation;
+ u64 refs;
+ u64 last = 0;
+ u32 nritems;
+ u32 blocksize;
+ struct btrfs_key key;
+ struct extent_buffer *eb;
int ret;
- int i;
- int refi = 0;
- int slot = path->slots[1];
- u32 blocksize = btrfs_level_size(root, 0);
- u32 refs;
-
- if (nritems == 0)
- goto out;
-
- root_owner = btrfs_header_owner(eb);
- root_gen = btrfs_header_generation(eb);
- sorted = kmalloc(sizeof(*sorted) * nritems, GFP_NOFS);
+ int slot;
+ int nread = 0;
- /*
- * step one, sort all the leaf pointers so we don't scribble
- * randomly into the extent allocation tree
- */
- for (i = slot; i < nritems; i++) {
- sorted[refi].bytenr = btrfs_node_blockptr(eb, i);
- sorted[refi].slot = i;
- refi++;
+ if (path->slots[wc->level] < wc->reada_slot) {
+ wc->reada_count = wc->reada_count * 2 / 3;
+ wc->reada_count = max(wc->reada_count, 2);
+ } else {
+ wc->reada_count = wc->reada_count * 3 / 2;
+ wc->reada_count = min_t(int, wc->reada_count,
+ BTRFS_NODEPTRS_PER_BLOCK(root));
}
- /*
- * nritems won't be zero, but if we're picking up drop_snapshot
- * after a crash, slot might be > 0, so double check things
- * just in case.
- */
- if (refi == 0)
- goto out;
+ eb = path->nodes[wc->level];
+ nritems = btrfs_header_nritems(eb);
+ blocksize = btrfs_level_size(root, wc->level - 1);
- sort(sorted, refi, sizeof(struct refsort), refsort_cmp, NULL);
+ for (slot = path->slots[wc->level]; slot < nritems; slot++) {
+ if (nread >= wc->reada_count)
+ break;
- /*
- * the first loop frees everything the leaves point to
- */
- for (i = 0; i < refi; i++) {
- u64 ptr_gen;
+ cond_resched();
+ bytenr = btrfs_node_blockptr(eb, slot);
+ generation = btrfs_node_ptr_generation(eb, slot);
- bytenr = sorted[i].bytenr;
+ if (slot == path->slots[wc->level])
+ goto reada;
- /*
- * check the reference count on this leaf. If it is > 1
- * we just decrement it below and don't update any
- * of the refs the leaf points to.
- */
- ret = drop_snap_lookup_refcount(trans, root, bytenr,
- blocksize, &refs);
- BUG_ON(ret);
- if (refs != 1)
+ if (wc->stage == UPDATE_BACKREF &&
+ generation <= root->root_key.offset)
continue;
- ptr_gen = btrfs_node_ptr_generation(eb, sorted[i].slot);
-
- /*
- * the leaf only had one reference, which means the
- * only thing pointing to this leaf is the snapshot
- * we're deleting. It isn't possible for the reference
- * count to increase again later
- *
- * The reference cache is checked for the leaf,
- * and if found we'll be able to drop any refs held by
- * the leaf without needing to read it in.
- */
- ref = btrfs_lookup_leaf_ref(root, bytenr);
- if (ref && ref->generation != ptr_gen) {
- btrfs_free_leaf_ref(root, ref);
- ref = NULL;
- }
- if (ref) {
- ret = cache_drop_leaf_ref(trans, root, ref);
- BUG_ON(ret);
- btrfs_remove_leaf_ref(root, ref);
- btrfs_free_leaf_ref(root, ref);
- } else {
- /*
- * the leaf wasn't in the reference cache, so
- * we have to read it.
- */
- leaf = read_tree_block(root, bytenr, blocksize,
- ptr_gen);
- ret = btrfs_drop_leaf_ref(trans, root, leaf);
+ if (wc->stage == DROP_REFERENCE) {
+ ret = btrfs_lookup_extent_info(trans, root,
+ bytenr, blocksize,
+ &refs, NULL);
BUG_ON(ret);
- free_extent_buffer(leaf);
- }
- atomic_inc(&root->fs_info->throttle_gen);
- wake_up(&root->fs_info->transaction_throttle);
- cond_resched();
- }
-
- /*
- * run through the loop again to free the refs on the leaves.
- * This is faster than doing it in the loop above because
- * the leaves are likely to be clustered together. We end up
- * working in nice chunks on the extent allocation tree.
- */
- for (i = 0; i < refi; i++) {
- bytenr = sorted[i].bytenr;
- ret = btrfs_free_extent(trans, root, bytenr,
- blocksize, eb->start,
- root_owner, root_gen, 0, 1);
- BUG_ON(ret);
-
- atomic_inc(&root->fs_info->throttle_gen);
- wake_up(&root->fs_info->transaction_throttle);
- cond_resched();
- }
-out:
- kfree(sorted);
+ BUG_ON(refs == 0);
+ if (refs == 1)
+ goto reada;
- /*
- * update the path to show we've processed the entire level 1
- * node. This will get saved into the root's drop_snapshot_progress
- * field so these drops are not repeated again if this transaction
- * commits.
- */
- path->slots[1] = nritems;
- return 0;
-}
-
-/*
- * helper function for drop_snapshot, this walks down the tree dropping ref
- * counts as it goes.
- */
-static noinline int walk_down_tree(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- struct btrfs_path *path, int *level)
-{
- u64 root_owner;
- u64 root_gen;
- u64 bytenr;
- u64 ptr_gen;
- struct extent_buffer *next;
- struct extent_buffer *cur;
- struct extent_buffer *parent;
- u32 blocksize;
- int ret;
- u32 refs;
-
- WARN_ON(*level < 0);
- WARN_ON(*level >= BTRFS_MAX_LEVEL);
- ret = drop_snap_lookup_refcount(trans, root, path->nodes[*level]->start,
- path->nodes[*level]->len, &refs);
- BUG_ON(ret);
- if (refs > 1)
- goto out;
-
- /*
- * walk down to the last node level and free all the leaves
- */
- while (*level >= 0) {
- WARN_ON(*level < 0);
- WARN_ON(*level >= BTRFS_MAX_LEVEL);
- cur = path->nodes[*level];
-
- if (btrfs_header_level(cur) != *level)
- WARN_ON(1);
-
- if (path->slots[*level] >=
- btrfs_header_nritems(cur))
- break;
-
- /* the new code goes down to level 1 and does all the
- * leaves pointed to that node in bulk. So, this check
- * for level 0 will always be false.
- *
- * But, the disk format allows the drop_snapshot_progress
- * field in the root to leave things in a state where
- * a leaf will need cleaning up here. If someone crashes
- * with the old code and then boots with the new code,
- * we might find a leaf here.
- */
- if (*level == 0) {
- ret = btrfs_drop_leaf_ref(trans, root, cur);
- BUG_ON(ret);
- break;
+ if (!wc->update_ref ||
+ generation <= root->root_key.offset)
+ continue;
+ btrfs_node_key_to_cpu(eb, &key, slot);
+ ret = btrfs_comp_cpu_keys(&key,
+ &wc->update_progress);
+ if (ret < 0)
+ continue;
}
-
- /*
- * once we get to level one, process the whole node
- * at once, including everything below it.
- */
- if (*level == 1) {
- ret = drop_level_one_refs(trans, root, path);
- BUG_ON(ret);
+reada:
+ ret = readahead_tree_block(root, bytenr, blocksize,
+ generation);
+ if (ret)
break;
- }
-
- bytenr = btrfs_node_blockptr(cur, path->slots[*level]);
- ptr_gen = btrfs_node_ptr_generation(cur, path->slots[*level]);
- blocksize = btrfs_level_size(root, *level - 1);
-
- ret = drop_snap_lookup_refcount(trans, root, bytenr,
- blocksize, &refs);
- BUG_ON(ret);
-
- /*
- * if there is more than one reference, we don't need
- * to read that node to drop any references it has. We
- * just drop the ref we hold on that node and move on to the
- * next slot in this level.
- */
- if (refs != 1) {
- parent = path->nodes[*level];
- root_owner = btrfs_header_owner(parent);
- root_gen = btrfs_header_generation(parent);
- path->slots[*level]++;
-
- ret = btrfs_free_extent(trans, root, bytenr,
- blocksize, parent->start,
- root_owner, root_gen,
- *level - 1, 1);
- BUG_ON(ret);
-
- atomic_inc(&root->fs_info->throttle_gen);
- wake_up(&root->fs_info->transaction_throttle);
- cond_resched();
-
- continue;
- }
-
- /*
- * we need to keep freeing things in the next level down.
- * read the block and loop around to process it
- */
- next = read_tree_block(root, bytenr, blocksize, ptr_gen);
- WARN_ON(*level <= 0);
- if (path->nodes[*level-1])
- free_extent_buffer(path->nodes[*level-1]);
- path->nodes[*level-1] = next;
- *level = btrfs_header_level(next);
- path->slots[*level] = 0;
- cond_resched();
+ last = bytenr + blocksize;
+ nread++;
}
-out:
- WARN_ON(*level < 0);
- WARN_ON(*level >= BTRFS_MAX_LEVEL);
-
- if (path->nodes[*level] == root->node) {
- parent = path->nodes[*level];
- bytenr = path->nodes[*level]->start;
- } else {
- parent = path->nodes[*level + 1];
- bytenr = btrfs_node_blockptr(parent, path->slots[*level + 1]);
- }
-
- blocksize = btrfs_level_size(root, *level);
- root_owner = btrfs_header_owner(parent);
- root_gen = btrfs_header_generation(parent);
-
- /*
- * cleanup and free the reference on the last node
- * we processed
- */
- ret = btrfs_free_extent(trans, root, bytenr, blocksize,
- parent->start, root_owner, root_gen,
- *level, 1);
- free_extent_buffer(path->nodes[*level]);
- path->nodes[*level] = NULL;
-
- *level += 1;
- BUG_ON(ret);
-
- cond_resched();
- return 0;
+ wc->reada_slot = slot;
}
-#endif
-
-struct walk_control {
- u64 refs[BTRFS_MAX_LEVEL];
- u64 flags[BTRFS_MAX_LEVEL];
- struct btrfs_key update_progress;
- int stage;
- int level;
- int shared_level;
- int update_ref;
- int keep_locks;
-};
-
-#define DROP_REFERENCE 1
-#define UPDATE_BACKREF 2
/*
* hepler to process tree block while walking down the tree.
*
- * when wc->stage == DROP_REFERENCE, this function checks
- * reference count of the block. if the block is shared and
- * we need update back refs for the subtree rooted at the
- * block, this function changes wc->stage to UPDATE_BACKREF
- *
* when wc->stage == UPDATE_BACKREF, this function updates
* back refs for pointers in the block.
*
{
int level = wc->level;
struct extent_buffer *eb = path->nodes[level];
- struct btrfs_key key;
u64 flag = BTRFS_BLOCK_FLAG_FULL_BACKREF;
int ret;
BUG_ON(wc->refs[level] == 0);
}
- if (wc->stage == DROP_REFERENCE &&
- wc->update_ref && wc->refs[level] > 1) {
- BUG_ON(eb == root->node);
- BUG_ON(path->slots[level] > 0);
- if (level == 0)
- btrfs_item_key_to_cpu(eb, &key, path->slots[level]);
- else
- btrfs_node_key_to_cpu(eb, &key, path->slots[level]);
- if (btrfs_header_owner(eb) == root->root_key.objectid &&
- btrfs_comp_cpu_keys(&key, &wc->update_progress) >= 0) {
- wc->stage = UPDATE_BACKREF;
- wc->shared_level = level;
- }
- }
-
if (wc->stage == DROP_REFERENCE) {
if (wc->refs[level] > 1)
return 1;
return 0;
}
+/*
+ * hepler to process tree block pointer.
+ *
+ * when wc->stage == DROP_REFERENCE, this function checks
+ * reference count of the block pointed to. if the block
+ * is shared and we need update back refs for the subtree
+ * rooted at the block, this function changes wc->stage to
+ * UPDATE_BACKREF. if the block is shared and there is no
+ * need to update back, this function drops the reference
+ * to the block.
+ *
+ * NOTE: return value 1 means we should stop walking down.
+ */
+static noinline int do_walk_down(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root,
+ struct btrfs_path *path,
+ struct walk_control *wc)
+{
+ u64 bytenr;
+ u64 generation;
+ u64 parent;
+ u32 blocksize;
+ struct btrfs_key key;
+ struct extent_buffer *next;
+ int level = wc->level;
+ int reada = 0;
+ int ret = 0;
+
+ generation = btrfs_node_ptr_generation(path->nodes[level],
+ path->slots[level]);
+ /*
+ * if the lower level block was created before the snapshot
+ * was created, we know there is no need to update back refs
+ * for the subtree
+ */
+ if (wc->stage == UPDATE_BACKREF &&
+ generation <= root->root_key.offset)
+ return 1;
+
+ bytenr = btrfs_node_blockptr(path->nodes[level], path->slots[level]);
+ blocksize = btrfs_level_size(root, level - 1);
+
+ next = btrfs_find_tree_block(root, bytenr, blocksize);
+ if (!next) {
+ next = btrfs_find_create_tree_block(root, bytenr, blocksize);
+ reada = 1;
+ }
+ btrfs_tree_lock(next);
+ btrfs_set_lock_blocking(next);
+
+ if (wc->stage == DROP_REFERENCE) {
+ ret = btrfs_lookup_extent_info(trans, root, bytenr, blocksize,
+ &wc->refs[level - 1],
+ &wc->flags[level - 1]);
+ BUG_ON(ret);
+ BUG_ON(wc->refs[level - 1] == 0);
+
+ if (wc->refs[level - 1] > 1) {
+ if (!wc->update_ref ||
+ generation <= root->root_key.offset)
+ goto skip;
+
+ btrfs_node_key_to_cpu(path->nodes[level], &key,
+ path->slots[level]);
+ ret = btrfs_comp_cpu_keys(&key, &wc->update_progress);
+ if (ret < 0)
+ goto skip;
+
+ wc->stage = UPDATE_BACKREF;
+ wc->shared_level = level - 1;
+ }
+ }
+
+ if (!btrfs_buffer_uptodate(next, generation)) {
+ btrfs_tree_unlock(next);
+ free_extent_buffer(next);
+ next = NULL;
+ }
+
+ if (!next) {
+ if (reada && level == 1)
+ reada_walk_down(trans, root, wc, path);
+ next = read_tree_block(root, bytenr, blocksize, generation);
+ btrfs_tree_lock(next);
+ btrfs_set_lock_blocking(next);
+ }
+
+ level--;
+ BUG_ON(level != btrfs_header_level(next));
+ path->nodes[level] = next;
+ path->slots[level] = 0;
+ path->locks[level] = 1;
+ wc->level = level;
+ if (wc->level == 1)
+ wc->reada_slot = 0;
+ return 0;
+skip:
+ wc->refs[level - 1] = 0;
+ wc->flags[level - 1] = 0;
+
+ if (wc->flags[level] & BTRFS_BLOCK_FLAG_FULL_BACKREF) {
+ parent = path->nodes[level]->start;
+ } else {
+ BUG_ON(root->root_key.objectid !=
+ btrfs_header_owner(path->nodes[level]));
+ parent = 0;
+ }
+
+ ret = btrfs_free_extent(trans, root, bytenr, blocksize, parent,
+ root->root_key.objectid, level - 1, 0);
+ BUG_ON(ret);
+
+ btrfs_tree_unlock(next);
+ free_extent_buffer(next);
+ return 1;
+}
+
/*
* hepler to process tree block while walking up the tree.
*
if (level < wc->shared_level)
goto out;
- BUG_ON(wc->refs[level] <= 1);
ret = find_next_key(path, level + 1, &wc->update_progress);
if (ret > 0)
wc->update_ref = 0;
path->locks[level] = 0;
return 1;
}
- } else {
- BUG_ON(level != 0);
}
}
struct btrfs_path *path,
struct walk_control *wc)
{
- struct extent_buffer *next;
- struct extent_buffer *cur;
- u64 bytenr;
- u64 ptr_gen;
- u32 blocksize;
int level = wc->level;
int ret;
while (level >= 0) {
- cur = path->nodes[level];
- BUG_ON(path->slots[level] >= btrfs_header_nritems(cur));
+ if (path->slots[level] >=
+ btrfs_header_nritems(path->nodes[level]))
+ break;
ret = walk_down_proc(trans, root, path, wc);
if (ret > 0)
if (level == 0)
break;
- bytenr = btrfs_node_blockptr(cur, path->slots[level]);
- blocksize = btrfs_level_size(root, level - 1);
- ptr_gen = btrfs_node_ptr_generation(cur, path->slots[level]);
-
- next = read_tree_block(root, bytenr, blocksize, ptr_gen);
- btrfs_tree_lock(next);
- btrfs_set_lock_blocking(next);
-
- level--;
- BUG_ON(level != btrfs_header_level(next));
- path->nodes[level] = next;
- path->slots[level] = 0;
- path->locks[level] = 1;
- wc->level = level;
+ ret = do_walk_down(trans, root, path, wc);
+ if (ret > 0) {
+ path->slots[level]++;
+ continue;
+ }
+ level = wc->level;
}
return 0;
}
err = ret;
goto out;
}
- btrfs_node_key_to_cpu(path->nodes[level], &key,
- path->slots[level]);
- WARN_ON(memcmp(&key, &wc->update_progress, sizeof(key)));
+ WARN_ON(ret > 0);
/*
* unlock our path, this is safe because only this
wc->stage = DROP_REFERENCE;
wc->update_ref = update_ref;
wc->keep_locks = 0;
+ wc->reada_count = BTRFS_NODEPTRS_PER_BLOCK(root);
while (1) {
ret = walk_down_tree(trans, root, path, wc);
ret = btrfs_del_root(trans, tree_root, &root->root_key);
BUG_ON(ret);
- free_extent_buffer(root->node);
- free_extent_buffer(root->commit_root);
- kfree(root);
+ if (root->root_key.objectid != BTRFS_TREE_RELOC_OBJECTID) {
+ ret = btrfs_find_last_root(tree_root, root->root_key.objectid,
+ NULL, NULL);
+ BUG_ON(ret < 0);
+ if (ret > 0) {
+ ret = btrfs_del_orphan_item(trans, tree_root,
+ root->root_key.objectid);
+ BUG_ON(ret);
+ }
+ }
+
+ if (root->in_radix) {
+ btrfs_free_fs_root(tree_root->fs_info, root);
+ } else {
+ free_extent_buffer(root->node);
+ free_extent_buffer(root->commit_root);
+ kfree(root);
+ }
out:
btrfs_end_transaction(trans, tree_root);
kfree(wc);
wc->stage = DROP_REFERENCE;
wc->update_ref = 0;
wc->keep_locks = 1;
+ wc->reada_count = BTRFS_NODEPTRS_PER_BLOCK(root);
while (1) {
wret = walk_down_tree(trans, root, path, wc);
lock_extent(&BTRFS_I(reloc_inode)->io_tree, start, end, GFP_NOFS);
while (1) {
int ret;
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
if (ret != -EEXIST) {
free_extent_map(em);
break;
return 0;
}
-#if 0
-static int __insert_orphan_inode(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- u64 objectid, u64 size)
-{
- struct btrfs_path *path;
- struct btrfs_inode_item *item;
- struct extent_buffer *leaf;
- int ret;
-
- path = btrfs_alloc_path();
- if (!path)
- return -ENOMEM;
-
- path->leave_spinning = 1;
- ret = btrfs_insert_empty_inode(trans, root, path, objectid);
- if (ret)
- goto out;
-
- leaf = path->nodes[0];
- item = btrfs_item_ptr(leaf, path->slots[0], struct btrfs_inode_item);
- memset_extent_buffer(leaf, 0, (unsigned long)item, sizeof(*item));
- btrfs_set_inode_generation(leaf, item, 1);
- btrfs_set_inode_size(leaf, item, size);
- btrfs_set_inode_mode(leaf, item, S_IFREG | 0600);
- btrfs_set_inode_flags(leaf, item, BTRFS_INODE_NOCOMPRESS);
- btrfs_mark_buffer_dirty(leaf);
- btrfs_release_path(root, path);
-out:
- btrfs_free_path(path);
- return ret;
-}
-
-static noinline struct inode *create_reloc_inode(struct btrfs_fs_info *fs_info,
- struct btrfs_block_group_cache *group)
+/*
+ * checks to see if its even possible to relocate this block group.
+ *
+ * @return - -1 if it's not a good idea to relocate this block group, 0 if its
+ * ok to go ahead and try.
+ */
+int btrfs_can_relocate(struct btrfs_root *root, u64 bytenr)
{
- struct inode *inode = NULL;
- struct btrfs_trans_handle *trans;
- struct btrfs_root *root;
- struct btrfs_key root_key;
- u64 objectid = BTRFS_FIRST_FREE_OBJECTID;
- int err = 0;
+ struct btrfs_block_group_cache *block_group;
+ struct btrfs_space_info *space_info;
+ struct btrfs_fs_devices *fs_devices = root->fs_info->fs_devices;
+ struct btrfs_device *device;
+ int full = 0;
+ int ret = 0;
- root_key.objectid = BTRFS_DATA_RELOC_TREE_OBJECTID;
- root_key.type = BTRFS_ROOT_ITEM_KEY;
- root_key.offset = (u64)-1;
- root = btrfs_read_fs_root_no_name(fs_info, &root_key);
- if (IS_ERR(root))
- return ERR_CAST(root);
+ block_group = btrfs_lookup_block_group(root->fs_info, bytenr);
- trans = btrfs_start_transaction(root, 1);
- BUG_ON(!trans);
+ /* odd, couldn't find the block group, leave it alone */
+ if (!block_group)
+ return -1;
- err = btrfs_find_free_objectid(trans, root, objectid, &objectid);
- if (err)
+ /* no bytes used, we're good */
+ if (!btrfs_block_group_used(&block_group->item))
goto out;
- err = __insert_orphan_inode(trans, root, objectid, group->key.offset);
- BUG_ON(err);
-
- err = btrfs_insert_file_extent(trans, root, objectid, 0, 0, 0,
- group->key.offset, 0, group->key.offset,
- 0, 0, 0);
- BUG_ON(err);
-
- inode = btrfs_iget_locked(root->fs_info->sb, objectid, root);
- if (inode->i_state & I_NEW) {
- BTRFS_I(inode)->root = root;
- BTRFS_I(inode)->location.objectid = objectid;
- BTRFS_I(inode)->location.type = BTRFS_INODE_ITEM_KEY;
- BTRFS_I(inode)->location.offset = 0;
- btrfs_read_locked_inode(inode);
- unlock_new_inode(inode);
- BUG_ON(is_bad_inode(inode));
- } else {
- BUG_ON(1);
- }
- BTRFS_I(inode)->index_cnt = group->key.objectid;
-
- err = btrfs_orphan_add(trans, inode);
-out:
- btrfs_end_transaction(trans, root);
- if (err) {
- if (inode)
- iput(inode);
- inode = ERR_PTR(err);
- }
- return inode;
-}
-
-int btrfs_reloc_clone_csums(struct inode *inode, u64 file_pos, u64 len)
-{
-
- struct btrfs_ordered_sum *sums;
- struct btrfs_sector_sum *sector_sum;
- struct btrfs_ordered_extent *ordered;
- struct btrfs_root *root = BTRFS_I(inode)->root;
- struct list_head list;
- size_t offset;
- int ret;
- u64 disk_bytenr;
-
- INIT_LIST_HEAD(&list);
-
- ordered = btrfs_lookup_ordered_extent(inode, file_pos);
- BUG_ON(ordered->file_offset != file_pos || ordered->len != len);
-
- disk_bytenr = file_pos + BTRFS_I(inode)->index_cnt;
- ret = btrfs_lookup_csums_range(root->fs_info->csum_root, disk_bytenr,
- disk_bytenr + len - 1, &list);
-
- while (!list_empty(&list)) {
- sums = list_entry(list.next, struct btrfs_ordered_sum, list);
- list_del_init(&sums->list);
-
- sector_sum = sums->sums;
- sums->bytenr = ordered->start;
+ space_info = block_group->space_info;
+ spin_lock(&space_info->lock);
- offset = 0;
- while (offset < sums->len) {
- sector_sum->bytenr += ordered->start - disk_bytenr;
- sector_sum++;
- offset += root->sectorsize;
- }
+ full = space_info->full;
- btrfs_add_ordered_sum(inode, ordered, sums);
+ /*
+ * if this is the last block group we have in this space, we can't
+ * relocate it unless we're able to allocate a new chunk below.
+ *
+ * Otherwise, we need to make sure we have room in the space to handle
+ * all of the extents from this block group. If we can, we're good
+ */
+ if ((space_info->total_bytes != block_group->key.offset) &&
+ (space_info->bytes_used + space_info->bytes_reserved +
+ space_info->bytes_pinned + space_info->bytes_readonly +
+ btrfs_block_group_used(&block_group->item) <
+ space_info->total_bytes)) {
+ spin_unlock(&space_info->lock);
+ goto out;
}
- btrfs_put_ordered_extent(ordered);
- return 0;
-}
-
-int btrfs_relocate_block_group(struct btrfs_root *root, u64 group_start)
-{
- struct btrfs_trans_handle *trans;
- struct btrfs_path *path;
- struct btrfs_fs_info *info = root->fs_info;
- struct extent_buffer *leaf;
- struct inode *reloc_inode;
- struct btrfs_block_group_cache *block_group;
- struct btrfs_key key;
- u64 skipped;
- u64 cur_byte;
- u64 total_found;
- u32 nritems;
- int ret;
- int progress;
- int pass = 0;
-
- root = root->fs_info->extent_root;
-
- block_group = btrfs_lookup_block_group(info, group_start);
- BUG_ON(!block_group);
-
- printk(KERN_INFO "btrfs relocating block group %llu flags %llu\n",
- (unsigned long long)block_group->key.objectid,
- (unsigned long long)block_group->flags);
-
- path = btrfs_alloc_path();
- BUG_ON(!path);
-
- reloc_inode = create_reloc_inode(info, block_group);
- BUG_ON(IS_ERR(reloc_inode));
-
- __alloc_chunk_for_shrink(root, block_group, 1);
- set_block_group_readonly(block_group);
-
- btrfs_start_delalloc_inodes(info->tree_root);
- btrfs_wait_ordered_extents(info->tree_root, 0);
-again:
- skipped = 0;
- total_found = 0;
- progress = 0;
- key.objectid = block_group->key.objectid;
- key.offset = 0;
- key.type = 0;
- cur_byte = key.objectid;
-
- trans = btrfs_start_transaction(info->tree_root, 1);
- btrfs_commit_transaction(trans, info->tree_root);
+ spin_unlock(&space_info->lock);
- mutex_lock(&root->fs_info->cleaner_mutex);
- btrfs_clean_old_snapshots(info->tree_root);
- btrfs_remove_leaf_refs(info->tree_root, (u64)-1, 1);
- mutex_unlock(&root->fs_info->cleaner_mutex);
+ /*
+ * ok we don't have enough space, but maybe we have free space on our
+ * devices to allocate new chunks for relocation, so loop through our
+ * alloc devices and guess if we have enough space. However, if we
+ * were marked as full, then we know there aren't enough chunks, and we
+ * can just return.
+ */
+ ret = -1;
+ if (full)
+ goto out;
- trans = btrfs_start_transaction(info->tree_root, 1);
- btrfs_commit_transaction(trans, info->tree_root);
+ mutex_lock(&root->fs_info->chunk_mutex);
+ list_for_each_entry(device, &fs_devices->alloc_list, dev_alloc_list) {
+ u64 min_free = btrfs_block_group_used(&block_group->item);
+ u64 dev_offset, max_avail;
- while (1) {
- ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
- if (ret < 0)
- goto out;
-next:
- leaf = path->nodes[0];
- nritems = btrfs_header_nritems(leaf);
- if (path->slots[0] >= nritems) {
- ret = btrfs_next_leaf(root, path);
- if (ret < 0)
- goto out;
- if (ret == 1) {
- ret = 0;
+ /*
+ * check to make sure we can actually find a chunk with enough
+ * space to fit our block group in.
+ */
+ if (device->total_bytes > device->bytes_used + min_free) {
+ ret = find_free_dev_extent(NULL, device, min_free,
+ &dev_offset, &max_avail);
+ if (!ret)
break;
- }
- leaf = path->nodes[0];
- nritems = btrfs_header_nritems(leaf);
- }
-
- btrfs_item_key_to_cpu(leaf, &key, path->slots[0]);
-
- if (key.objectid >= block_group->key.objectid +
- block_group->key.offset)
- break;
-
- if (progress && need_resched()) {
- btrfs_release_path(root, path);
- cond_resched();
- progress = 0;
- continue;
- }
- progress = 1;
-
- if (btrfs_key_type(&key) != BTRFS_EXTENT_ITEM_KEY ||
- key.objectid + key.offset <= cur_byte) {
- path->slots[0]++;
- goto next;
- }
-
- total_found++;
- cur_byte = key.objectid + key.offset;
- btrfs_release_path(root, path);
-
- __alloc_chunk_for_shrink(root, block_group, 0);
- ret = relocate_one_extent(root, path, &key, block_group,
- reloc_inode, pass);
- BUG_ON(ret < 0);
- if (ret > 0)
- skipped++;
-
- key.objectid = cur_byte;
- key.type = 0;
- key.offset = 0;
- }
-
- btrfs_release_path(root, path);
-
- if (pass == 0) {
- btrfs_wait_ordered_range(reloc_inode, 0, (u64)-1);
- invalidate_mapping_pages(reloc_inode->i_mapping, 0, -1);
- }
-
- if (total_found > 0) {
- printk(KERN_INFO "btrfs found %llu extents in pass %d\n",
- (unsigned long long)total_found, pass);
- pass++;
- if (total_found == skipped && pass > 2) {
- iput(reloc_inode);
- reloc_inode = create_reloc_inode(info, block_group);
- pass = 0;
+ ret = -1;
}
- goto again;
}
-
- /* delete reloc_inode */
- iput(reloc_inode);
-
- /* unpin extents in this range */
- trans = btrfs_start_transaction(info->tree_root, 1);
- btrfs_commit_transaction(trans, info->tree_root);
-
- spin_lock(&block_group->lock);
- WARN_ON(block_group->pinned > 0);
- WARN_ON(block_group->reserved > 0);
- WARN_ON(btrfs_block_group_used(&block_group->item) > 0);
- spin_unlock(&block_group->lock);
- btrfs_put_block_group(block_group);
- ret = 0;
+ mutex_unlock(&root->fs_info->chunk_mutex);
out:
- btrfs_free_path(path);
+ btrfs_put_block_group(block_group);
return ret;
}
-#endif
static int find_first_block_group(struct btrfs_root *root,
struct btrfs_path *path, struct btrfs_key *key)
{
struct btrfs_block_group_cache *block_group;
struct btrfs_space_info *space_info;
+ struct btrfs_caching_control *caching_ctl;
struct rb_node *n;
+ down_write(&info->extent_commit_sem);
+ while (!list_empty(&info->caching_block_groups)) {
+ caching_ctl = list_entry(info->caching_block_groups.next,
+ struct btrfs_caching_control, list);
+ list_del(&caching_ctl->list);
+ put_caching_control(caching_ctl);
+ }
+ up_write(&info->extent_commit_sem);
+
spin_lock(&info->block_group_cache_lock);
while ((n = rb_last(&info->block_group_cache_tree)) != NULL) {
block_group = rb_entry(n, struct btrfs_block_group_cache,
up_write(&block_group->space_info->groups_sem);
if (block_group->cached == BTRFS_CACHE_STARTED)
- wait_event(block_group->caching_q,
- block_group_cache_done(block_group));
+ wait_block_group_cache_done(block_group);
btrfs_remove_free_space_cache(block_group);
spin_lock_init(&cache->lock);
spin_lock_init(&cache->tree_lock);
cache->fs_info = info;
- init_waitqueue_head(&cache->caching_q);
INIT_LIST_HEAD(&cache->list);
INIT_LIST_HEAD(&cache->cluster_list);
cache->flags = btrfs_block_group_flags(&cache->item);
cache->sectorsize = root->sectorsize;
- remove_sb_from_cache(root, cache);
-
/*
* check for two cases, either we are full, and therefore
* don't need to bother with the caching work since we won't
* time, particularly in the full case.
*/
if (found_key.offset == btrfs_block_group_used(&cache->item)) {
+ exclude_super_stripes(root, cache);
+ cache->last_byte_to_unpin = (u64)-1;
cache->cached = BTRFS_CACHE_FINISHED;
+ free_excluded_extents(root, cache);
} else if (btrfs_block_group_used(&cache->item) == 0) {
+ exclude_super_stripes(root, cache);
+ cache->last_byte_to_unpin = (u64)-1;
cache->cached = BTRFS_CACHE_FINISHED;
add_new_free_space(cache, root->fs_info,
found_key.objectid,
found_key.objectid +
found_key.offset);
+ free_excluded_extents(root, cache);
}
ret = update_space_info(info, cache->flags, found_key.offset,
&space_info);
BUG_ON(ret);
cache->space_info = space_info;
+ spin_lock(&cache->space_info->lock);
+ cache->space_info->bytes_super += cache->bytes_super;
+ spin_unlock(&cache->space_info->lock);
+
down_write(&space_info->groups_sem);
list_add_tail(&cache->list, &space_info->block_groups);
up_write(&space_info->groups_sem);
atomic_set(&cache->count, 1);
spin_lock_init(&cache->lock);
spin_lock_init(&cache->tree_lock);
- init_waitqueue_head(&cache->caching_q);
INIT_LIST_HEAD(&cache->list);
INIT_LIST_HEAD(&cache->cluster_list);
cache->flags = type;
btrfs_set_block_group_flags(&cache->item, type);
+ cache->last_byte_to_unpin = (u64)-1;
cache->cached = BTRFS_CACHE_FINISHED;
- remove_sb_from_cache(root, cache);
+ exclude_super_stripes(root, cache);
add_new_free_space(cache, root->fs_info, chunk_offset,
chunk_offset + size);
+ free_excluded_extents(root, cache);
+
ret = update_space_info(root->fs_info, cache->flags, size, bytes_used,
&cache->space_info);
BUG_ON(ret);
+
+ spin_lock(&cache->space_info->lock);
+ cache->space_info->bytes_super += cache->bytes_super;
+ spin_unlock(&cache->space_info->lock);
+
down_write(&cache->space_info->groups_sem);
list_add_tail(&cache->list, &cache->space_info->block_groups);
up_write(&cache->space_info->groups_sem);
up_write(&block_group->space_info->groups_sem);
if (block_group->cached == BTRFS_CACHE_STARTED)
- wait_event(block_group->caching_q,
- block_group_cache_done(block_group));
+ wait_block_group_cache_done(block_group);
btrfs_remove_free_space_cache(block_group);
return NULL;
}
+static void merge_cb(struct extent_io_tree *tree, struct extent_state *new,
+ struct extent_state *other)
+{
+ if (tree->ops && tree->ops->merge_extent_hook)
+ tree->ops->merge_extent_hook(tree->mapping->host, new,
+ other);
+}
+
/*
* utility function to look for merge candidates inside a given range.
* Any extents with matching state are merged together into a single
other = rb_entry(other_node, struct extent_state, rb_node);
if (other->end == state->start - 1 &&
other->state == state->state) {
+ merge_cb(tree, state, other);
state->start = other->start;
other->tree = NULL;
rb_erase(&other->rb_node, &tree->state);
other = rb_entry(other_node, struct extent_state, rb_node);
if (other->start == state->end + 1 &&
other->state == state->state) {
+ merge_cb(tree, state, other);
other->start = state->start;
state->tree = NULL;
rb_erase(&state->rb_node, &tree->state);
free_extent_state(state);
+ state = NULL;
}
}
+
return 0;
}
-static void set_state_cb(struct extent_io_tree *tree,
+static int set_state_cb(struct extent_io_tree *tree,
struct extent_state *state,
unsigned long bits)
{
if (tree->ops && tree->ops->set_bit_hook) {
- tree->ops->set_bit_hook(tree->mapping->host, state->start,
- state->end, state->state, bits);
+ return tree->ops->set_bit_hook(tree->mapping->host,
+ state->start, state->end,
+ state->state, bits);
}
+
+ return 0;
}
static void clear_state_cb(struct extent_io_tree *tree,
struct extent_state *state,
unsigned long bits)
{
- if (tree->ops && tree->ops->clear_bit_hook) {
- tree->ops->clear_bit_hook(tree->mapping->host, state->start,
- state->end, state->state, bits);
- }
+ if (tree->ops && tree->ops->clear_bit_hook)
+ tree->ops->clear_bit_hook(tree->mapping->host, state, bits);
}
/*
int bits)
{
struct rb_node *node;
+ int ret;
if (end < start) {
printk(KERN_ERR "btrfs end < start %llu %llu\n",
(unsigned long long)start);
WARN_ON(1);
}
+ state->start = start;
+ state->end = end;
+ ret = set_state_cb(tree, state, bits);
+ if (ret)
+ return ret;
+
if (bits & EXTENT_DIRTY)
tree->dirty_bytes += end - start + 1;
- set_state_cb(tree, state, bits);
state->state |= bits;
- state->start = start;
- state->end = end;
node = tree_insert(&tree->state, end, &state->rb_node);
if (node) {
struct extent_state *found;
return 0;
}
+static int split_cb(struct extent_io_tree *tree, struct extent_state *orig,
+ u64 split)
+{
+ if (tree->ops && tree->ops->split_extent_hook)
+ return tree->ops->split_extent_hook(tree->mapping->host,
+ orig, split);
+ return 0;
+}
+
/*
* split a given extent state struct in two, inserting the preallocated
* struct 'prealloc' as the newly created second half. 'split' indicates an
struct extent_state *prealloc, u64 split)
{
struct rb_node *node;
+
+ split_cb(tree, orig, split);
+
prealloc->start = orig->start;
prealloc->end = split - 1;
prealloc->state = orig->state;
* bits were already set, or zero if none of the bits were already set.
*/
int clear_extent_bit(struct extent_io_tree *tree, u64 start, u64 end,
- int bits, int wake, int delete, gfp_t mask)
+ int bits, int wake, int delete,
+ struct extent_state **cached_state,
+ gfp_t mask)
{
struct extent_state *state;
+ struct extent_state *cached;
struct extent_state *prealloc = NULL;
+ struct rb_node *next_node;
struct rb_node *node;
u64 last_end;
int err;
}
spin_lock(&tree->lock);
+ if (cached_state) {
+ cached = *cached_state;
+ *cached_state = NULL;
+ cached_state = NULL;
+ if (cached && cached->tree && cached->start == start) {
+ atomic_dec(&cached->refs);
+ state = cached;
+ goto hit_next;
+ }
+ free_extent_state(cached);
+ }
/*
* this search will find the extents that end after
* our range starts
if (!node)
goto out;
state = rb_entry(node, struct extent_state, rb_node);
+hit_next:
if (state->start > end)
goto out;
WARN_ON(state->end < start);
if (err)
goto out;
if (state->end <= end) {
- set |= clear_state_bit(tree, state, bits,
- wake, delete);
+ set |= clear_state_bit(tree, state, bits, wake,
+ delete);
if (last_end == (u64)-1)
goto out;
start = last_end + 1;
- } else {
- start = state->start;
}
goto search_again;
}
prealloc = alloc_extent_state(GFP_ATOMIC);
err = split_state(tree, state, prealloc, end + 1);
BUG_ON(err == -EEXIST);
-
if (wake)
wake_up(&state->wq);
- set |= clear_state_bit(tree, prealloc, bits,
- wake, delete);
+
+ set |= clear_state_bit(tree, prealloc, bits, wake, delete);
+
prealloc = NULL;
goto out;
}
+ if (state->end < end && prealloc && !need_resched())
+ next_node = rb_next(&state->rb_node);
+ else
+ next_node = NULL;
+
set |= clear_state_bit(tree, state, bits, wake, delete);
if (last_end == (u64)-1)
goto out;
start = last_end + 1;
+ if (start <= end && next_node) {
+ state = rb_entry(next_node, struct extent_state,
+ rb_node);
+ if (state->start == start)
+ goto hit_next;
+ }
goto search_again;
out:
return 0;
}
-static void set_state_bits(struct extent_io_tree *tree,
+static int set_state_bits(struct extent_io_tree *tree,
struct extent_state *state,
int bits)
{
+ int ret;
+
+ ret = set_state_cb(tree, state, bits);
+ if (ret)
+ return ret;
+
if ((bits & EXTENT_DIRTY) && !(state->state & EXTENT_DIRTY)) {
u64 range = state->end - state->start + 1;
tree->dirty_bytes += range;
}
- set_state_cb(tree, state, bits);
state->state |= bits;
+
+ return 0;
+}
+
+static void cache_state(struct extent_state *state,
+ struct extent_state **cached_ptr)
+{
+ if (cached_ptr && !(*cached_ptr)) {
+ if (state->state & (EXTENT_IOBITS | EXTENT_BOUNDARY)) {
+ *cached_ptr = state;
+ atomic_inc(&state->refs);
+ }
+ }
}
/*
- * set some bits on a range in the tree. This may require allocations
- * or sleeping, so the gfp mask is used to indicate what is allowed.
+ * set some bits on a range in the tree. This may require allocations or
+ * sleeping, so the gfp mask is used to indicate what is allowed.
*
- * If 'exclusive' == 1, this will fail with -EEXIST if some part of the
- * range already has the desired bits set. The start of the existing
- * range is returned in failed_start in this case.
+ * If any of the exclusive bits are set, this will fail with -EEXIST if some
+ * part of the range already has the desired bits set. The start of the
+ * existing range is returned in failed_start in this case.
*
- * [start, end] is inclusive
- * This takes the tree lock.
+ * [start, end] is inclusive This takes the tree lock.
*/
+
static int set_extent_bit(struct extent_io_tree *tree, u64 start, u64 end,
- int bits, int exclusive, u64 *failed_start,
+ int bits, int exclusive_bits, u64 *failed_start,
+ struct extent_state **cached_state,
gfp_t mask)
{
struct extent_state *state;
struct extent_state *prealloc = NULL;
struct rb_node *node;
int err = 0;
- int set;
u64 last_start;
u64 last_end;
+
again:
if (!prealloc && (mask & __GFP_WAIT)) {
prealloc = alloc_extent_state(mask);
}
spin_lock(&tree->lock);
+ if (cached_state && *cached_state) {
+ state = *cached_state;
+ if (state->start == start && state->tree) {
+ node = &state->rb_node;
+ goto hit_next;
+ }
+ }
/*
* this search will find all the extents that end after
* our range starts.
BUG_ON(err == -EEXIST);
goto out;
}
-
state = rb_entry(node, struct extent_state, rb_node);
+hit_next:
last_start = state->start;
last_end = state->end;
* Just lock what we found and keep going
*/
if (state->start == start && state->end <= end) {
- set = state->state & bits;
- if (set && exclusive) {
+ struct rb_node *next_node;
+ if (state->state & exclusive_bits) {
*failed_start = state->start;
err = -EEXIST;
goto out;
}
- set_state_bits(tree, state, bits);
+
+ err = set_state_bits(tree, state, bits);
+ if (err)
+ goto out;
+
+ cache_state(state, cached_state);
merge_state(tree, state);
if (last_end == (u64)-1)
goto out;
+
start = last_end + 1;
+ if (start < end && prealloc && !need_resched()) {
+ next_node = rb_next(node);
+ if (next_node) {
+ state = rb_entry(next_node, struct extent_state,
+ rb_node);
+ if (state->start == start)
+ goto hit_next;
+ }
+ }
goto search_again;
}
* desired bit on it.
*/
if (state->start < start) {
- set = state->state & bits;
- if (exclusive && set) {
+ if (state->state & exclusive_bits) {
*failed_start = start;
err = -EEXIST;
goto out;
if (err)
goto out;
if (state->end <= end) {
- set_state_bits(tree, state, bits);
+ err = set_state_bits(tree, state, bits);
+ if (err)
+ goto out;
+ cache_state(state, cached_state);
merge_state(tree, state);
if (last_end == (u64)-1)
goto out;
start = last_end + 1;
- } else {
- start = state->start;
}
goto search_again;
}
this_end = last_start - 1;
err = insert_state(tree, prealloc, start, this_end,
bits);
- prealloc = NULL;
BUG_ON(err == -EEXIST);
- if (err)
+ if (err) {
+ prealloc = NULL;
goto out;
+ }
+ cache_state(prealloc, cached_state);
+ prealloc = NULL;
start = this_end + 1;
goto search_again;
}
* on the first half
*/
if (state->start <= end && state->end > end) {
- set = state->state & bits;
- if (exclusive && set) {
+ if (state->state & exclusive_bits) {
*failed_start = start;
err = -EEXIST;
goto out;
err = split_state(tree, state, prealloc, end + 1);
BUG_ON(err == -EEXIST);
- set_state_bits(tree, prealloc, bits);
+ err = set_state_bits(tree, prealloc, bits);
+ if (err) {
+ prealloc = NULL;
+ goto out;
+ }
+ cache_state(prealloc, cached_state);
merge_state(tree, prealloc);
prealloc = NULL;
goto out;
gfp_t mask)
{
return set_extent_bit(tree, start, end, EXTENT_DIRTY, 0, NULL,
- mask);
-}
-
-int set_extent_ordered(struct extent_io_tree *tree, u64 start, u64 end,
- gfp_t mask)
-{
- return set_extent_bit(tree, start, end, EXTENT_ORDERED, 0, NULL, mask);
+ NULL, mask);
}
int set_extent_bits(struct extent_io_tree *tree, u64 start, u64 end,
int bits, gfp_t mask)
{
return set_extent_bit(tree, start, end, bits, 0, NULL,
- mask);
+ NULL, mask);
}
int clear_extent_bits(struct extent_io_tree *tree, u64 start, u64 end,
int bits, gfp_t mask)
{
- return clear_extent_bit(tree, start, end, bits, 0, 0, mask);
+ return clear_extent_bit(tree, start, end, bits, 0, 0, NULL, mask);
}
int set_extent_delalloc(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
return set_extent_bit(tree, start, end,
- EXTENT_DELALLOC | EXTENT_DIRTY,
- 0, NULL, mask);
+ EXTENT_DELALLOC | EXTENT_DIRTY | EXTENT_UPTODATE,
+ 0, NULL, NULL, mask);
}
int clear_extent_dirty(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
return clear_extent_bit(tree, start, end,
- EXTENT_DIRTY | EXTENT_DELALLOC, 0, 0, mask);
-}
-
-int clear_extent_ordered(struct extent_io_tree *tree, u64 start, u64 end,
- gfp_t mask)
-{
- return clear_extent_bit(tree, start, end, EXTENT_ORDERED, 1, 0, mask);
+ EXTENT_DIRTY | EXTENT_DELALLOC, 0, 0,
+ NULL, mask);
}
int set_extent_new(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
return set_extent_bit(tree, start, end, EXTENT_NEW, 0, NULL,
- mask);
+ NULL, mask);
}
static int clear_extent_new(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
- return clear_extent_bit(tree, start, end, EXTENT_NEW, 0, 0, mask);
+ return clear_extent_bit(tree, start, end, EXTENT_NEW, 0, 0,
+ NULL, mask);
}
int set_extent_uptodate(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
return set_extent_bit(tree, start, end, EXTENT_UPTODATE, 0, NULL,
- mask);
+ NULL, mask);
}
static int clear_extent_uptodate(struct extent_io_tree *tree, u64 start,
u64 end, gfp_t mask)
{
- return clear_extent_bit(tree, start, end, EXTENT_UPTODATE, 0, 0, mask);
-}
-
-static int set_extent_writeback(struct extent_io_tree *tree, u64 start, u64 end,
- gfp_t mask)
-{
- return set_extent_bit(tree, start, end, EXTENT_WRITEBACK,
- 0, NULL, mask);
-}
-
-static int clear_extent_writeback(struct extent_io_tree *tree, u64 start,
- u64 end, gfp_t mask)
-{
- return clear_extent_bit(tree, start, end, EXTENT_WRITEBACK, 1, 0, mask);
+ return clear_extent_bit(tree, start, end, EXTENT_UPTODATE, 0, 0,
+ NULL, mask);
}
int wait_on_extent_writeback(struct extent_io_tree *tree, u64 start, u64 end)
* either insert or lock state struct between start and end use mask to tell
* us if waiting is desired.
*/
-int lock_extent(struct extent_io_tree *tree, u64 start, u64 end, gfp_t mask)
+int lock_extent_bits(struct extent_io_tree *tree, u64 start, u64 end,
+ int bits, struct extent_state **cached_state, gfp_t mask)
{
int err;
u64 failed_start;
while (1) {
- err = set_extent_bit(tree, start, end, EXTENT_LOCKED, 1,
- &failed_start, mask);
+ err = set_extent_bit(tree, start, end, EXTENT_LOCKED | bits,
+ EXTENT_LOCKED, &failed_start,
+ cached_state, mask);
if (err == -EEXIST && (mask & __GFP_WAIT)) {
wait_extent_bit(tree, failed_start, end, EXTENT_LOCKED);
start = failed_start;
return err;
}
+int lock_extent(struct extent_io_tree *tree, u64 start, u64 end, gfp_t mask)
+{
+ return lock_extent_bits(tree, start, end, 0, NULL, mask);
+}
+
int try_lock_extent(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
int err;
u64 failed_start;
- err = set_extent_bit(tree, start, end, EXTENT_LOCKED, 1,
- &failed_start, mask);
+ err = set_extent_bit(tree, start, end, EXTENT_LOCKED, EXTENT_LOCKED,
+ &failed_start, NULL, mask);
if (err == -EEXIST) {
if (failed_start > start)
clear_extent_bit(tree, start, failed_start - 1,
- EXTENT_LOCKED, 1, 0, mask);
+ EXTENT_LOCKED, 1, 0, NULL, mask);
return 0;
}
return 1;
}
+int unlock_extent_cached(struct extent_io_tree *tree, u64 start, u64 end,
+ struct extent_state **cached, gfp_t mask)
+{
+ return clear_extent_bit(tree, start, end, EXTENT_LOCKED, 1, 0, cached,
+ mask);
+}
+
int unlock_extent(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask)
{
- return clear_extent_bit(tree, start, end, EXTENT_LOCKED, 1, 0, mask);
+ return clear_extent_bit(tree, start, end, EXTENT_LOCKED, 1, 0, NULL,
+ mask);
}
/*
page_cache_release(page);
index++;
}
- set_extent_dirty(tree, start, end, GFP_NOFS);
return 0;
}
page_cache_release(page);
index++;
}
- set_extent_writeback(tree, start, end, GFP_NOFS);
return 0;
}
u64 delalloc_start;
u64 delalloc_end;
u64 found;
+ struct extent_state *cached_state = NULL;
int ret;
int loops = 0;
/* some of the pages are gone, lets avoid looping by
* shortening the size of the delalloc range we're searching
*/
+ free_extent_state(cached_state);
if (!loops) {
unsigned long offset = (*start) & (PAGE_CACHE_SIZE - 1);
max_bytes = PAGE_CACHE_SIZE - offset;
BUG_ON(ret);
/* step three, lock the state bits for the whole range */
- lock_extent(tree, delalloc_start, delalloc_end, GFP_NOFS);
+ lock_extent_bits(tree, delalloc_start, delalloc_end,
+ 0, &cached_state, GFP_NOFS);
/* then test to make sure it is all still delalloc */
ret = test_range_bit(tree, delalloc_start, delalloc_end,
- EXTENT_DELALLOC, 1);
+ EXTENT_DELALLOC, 1, cached_state);
if (!ret) {
- unlock_extent(tree, delalloc_start, delalloc_end, GFP_NOFS);
+ unlock_extent_cached(tree, delalloc_start, delalloc_end,
+ &cached_state, GFP_NOFS);
__unlock_for_delalloc(inode, locked_page,
delalloc_start, delalloc_end);
cond_resched();
goto again;
}
+ free_extent_state(cached_state);
*start = delalloc_start;
*end = delalloc_end;
out_failed:
int clear_unlock,
int clear_delalloc, int clear_dirty,
int set_writeback,
- int end_writeback)
+ int end_writeback,
+ int set_private2)
{
int ret;
struct page *pages[16];
if (clear_delalloc)
clear_bits |= EXTENT_DELALLOC;
- clear_extent_bit(tree, start, end, clear_bits, 1, 0, GFP_NOFS);
- if (!(unlock_pages || clear_dirty || set_writeback || end_writeback))
+ clear_extent_bit(tree, start, end, clear_bits, 1, 0, NULL, GFP_NOFS);
+ if (!(unlock_pages || clear_dirty || set_writeback || end_writeback ||
+ set_private2))
return 0;
while (nr_pages > 0) {
min_t(unsigned long,
nr_pages, ARRAY_SIZE(pages)), pages);
for (i = 0; i < ret; i++) {
+
+ if (set_private2)
+ SetPagePrivate2(pages[i]);
+
if (pages[i] == locked_page) {
page_cache_release(pages[i]);
continue;
* range is found set.
*/
int test_range_bit(struct extent_io_tree *tree, u64 start, u64 end,
- int bits, int filled)
+ int bits, int filled, struct extent_state *cached)
{
struct extent_state *state = NULL;
struct rb_node *node;
int bitset = 0;
spin_lock(&tree->lock);
- node = tree_search(tree, start);
+ if (cached && cached->tree && cached->start == start)
+ node = &cached->rb_node;
+ else
+ node = tree_search(tree, start);
while (node && start <= end) {
state = rb_entry(node, struct extent_state, rb_node);
bitset = 0;
break;
}
+
+ if (state->end == (u64)-1)
+ break;
+
start = state->end + 1;
if (start > end)
break;
{
u64 start = (u64)page->index << PAGE_CACHE_SHIFT;
u64 end = start + PAGE_CACHE_SIZE - 1;
- if (test_range_bit(tree, start, end, EXTENT_UPTODATE, 1))
+ if (test_range_bit(tree, start, end, EXTENT_UPTODATE, 1, NULL))
SetPageUptodate(page);
return 0;
}
{
u64 start = (u64)page->index << PAGE_CACHE_SHIFT;
u64 end = start + PAGE_CACHE_SIZE - 1;
- if (!test_range_bit(tree, start, end, EXTENT_LOCKED, 0))
+ if (!test_range_bit(tree, start, end, EXTENT_LOCKED, 0, NULL))
unlock_page(page);
return 0;
}
static int check_page_writeback(struct extent_io_tree *tree,
struct page *page)
{
- u64 start = (u64)page->index << PAGE_CACHE_SHIFT;
- u64 end = start + PAGE_CACHE_SIZE - 1;
- if (!test_range_bit(tree, start, end, EXTENT_WRITEBACK, 0))
- end_page_writeback(page);
+ end_page_writeback(page);
return 0;
}
}
if (!uptodate) {
- clear_extent_uptodate(tree, start, end, GFP_ATOMIC);
+ clear_extent_uptodate(tree, start, end, GFP_NOFS);
ClearPageUptodate(page);
SetPageError(page);
}
- clear_extent_writeback(tree, start, end, GFP_ATOMIC);
-
if (whole_page)
end_page_writeback(page);
else
continue;
}
/* the get_extent function already copied into the page */
- if (test_range_bit(tree, cur, cur_end, EXTENT_UPTODATE, 1)) {
+ if (test_range_bit(tree, cur, cur_end,
+ EXTENT_UPTODATE, 1, NULL)) {
check_page_uptodate(tree, page);
unlock_extent(tree, cur, cur + iosize - 1, GFP_NOFS);
cur = cur + iosize;
u64 iosize;
u64 unlock_start;
sector_t sector;
+ struct extent_state *cached_state = NULL;
struct extent_map *em;
struct block_device *bdev;
int ret;
delalloc_end = 0;
page_started = 0;
if (!epd->extent_locked) {
+ u64 delalloc_to_write = 0;
/*
* make sure the wbc mapping index is at least updated
* to this page.
tree->ops->fill_delalloc(inode, page, delalloc_start,
delalloc_end, &page_started,
&nr_written);
+ /*
+ * delalloc_end is already one less than the total
+ * length, so we don't subtract one from
+ * PAGE_CACHE_SIZE
+ */
+ delalloc_to_write += (delalloc_end - delalloc_start +
+ PAGE_CACHE_SIZE) >>
+ PAGE_CACHE_SHIFT;
delalloc_start = delalloc_end + 1;
}
+ if (wbc->nr_to_write < delalloc_to_write) {
+ int thresh = 8192;
+
+ if (delalloc_to_write < thresh * 2)
+ thresh = delalloc_to_write;
+ wbc->nr_to_write = min_t(u64, delalloc_to_write,
+ thresh);
+ }
/* did the fill delalloc function already unlock and start
* the IO?
goto done_unlocked;
}
}
- lock_extent(tree, start, page_end, GFP_NOFS);
-
- unlock_start = start;
-
if (tree->ops && tree->ops->writepage_start_hook) {
ret = tree->ops->writepage_start_hook(page, start,
page_end);
if (ret == -EAGAIN) {
- unlock_extent(tree, start, page_end, GFP_NOFS);
redirty_page_for_writepage(wbc, page);
update_nr_written(page, wbc, nr_written);
unlock_page(page);
update_nr_written(page, wbc, nr_written + 1);
end = page_end;
- if (test_range_bit(tree, start, page_end, EXTENT_DELALLOC, 0))
- printk(KERN_ERR "btrfs delalloc bits after lock_extent\n");
-
if (last_byte <= start) {
- clear_extent_dirty(tree, start, page_end, GFP_NOFS);
- unlock_extent(tree, start, page_end, GFP_NOFS);
if (tree->ops && tree->ops->writepage_end_io_hook)
tree->ops->writepage_end_io_hook(page, start,
page_end, NULL, 1);
goto done;
}
- set_extent_uptodate(tree, start, page_end, GFP_NOFS);
blocksize = inode->i_sb->s_blocksize;
while (cur <= end) {
if (cur >= last_byte) {
- clear_extent_dirty(tree, cur, page_end, GFP_NOFS);
- unlock_extent(tree, unlock_start, page_end, GFP_NOFS);
if (tree->ops && tree->ops->writepage_end_io_hook)
tree->ops->writepage_end_io_hook(page, cur,
page_end, NULL, 1);
*/
if (compressed || block_start == EXTENT_MAP_HOLE ||
block_start == EXTENT_MAP_INLINE) {
- clear_extent_dirty(tree, cur,
- cur + iosize - 1, GFP_NOFS);
-
- unlock_extent(tree, unlock_start, cur + iosize - 1,
- GFP_NOFS);
-
/*
* end_io notification does not happen here for
* compressed extents
}
/* leave this out until we have a page_mkwrite call */
if (0 && !test_range_bit(tree, cur, cur + iosize - 1,
- EXTENT_DIRTY, 0)) {
+ EXTENT_DIRTY, 0, NULL)) {
cur = cur + iosize;
pg_offset += iosize;
continue;
}
- clear_extent_dirty(tree, cur, cur + iosize - 1, GFP_NOFS);
if (tree->ops && tree->ops->writepage_io_hook) {
ret = tree->ops->writepage_io_hook(page, cur,
cur + iosize - 1);
set_page_writeback(page);
end_page_writeback(page);
}
- if (unlock_start <= page_end)
- unlock_extent(tree, unlock_start, page_end, GFP_NOFS);
unlock_page(page);
done_unlocked:
+ /* drop our reference on any cached states */
+ free_extent_state(cached_state);
return 0;
}
writepage_t writepage, void *data,
void (*flush_fn)(void *))
{
- struct backing_dev_info *bdi = mapping->backing_dev_info;
int ret = 0;
int done = 0;
+ int nr_to_write_done = 0;
struct pagevec pvec;
int nr_pages;
pgoff_t index;
scanned = 1;
}
retry:
- while (!done && (index <= end) &&
+ while (!done && !nr_to_write_done && (index <= end) &&
(nr_pages = pagevec_lookup_tag(&pvec, mapping, &index,
PAGECACHE_TAG_DIRTY, min(end - index,
(pgoff_t)PAGEVEC_SIZE-1) + 1))) {
unlock_page(page);
ret = 0;
}
- if (ret || wbc->nr_to_write <= 0)
- done = 1;
- if (wbc->nonblocking && bdi_write_congested(bdi)) {
- wbc->encountered_congestion = 1;
+ if (ret)
done = 1;
- }
+
+ /*
+ * the filesystem may choose to bump up nr_to_write.
+ * We have to make sure to honor the new nr_to_write
+ * at any time
+ */
+ nr_to_write_done = wbc->nr_to_write <= 0;
}
pagevec_release(&pvec);
cond_resched();
return 0;
lock_extent(tree, start, end, GFP_NOFS);
- wait_on_extent_writeback(tree, start, end);
+ wait_on_page_writeback(page);
clear_extent_bit(tree, start, end,
EXTENT_LOCKED | EXTENT_DIRTY | EXTENT_DELALLOC,
- 1, 1, GFP_NOFS);
+ 1, 1, NULL, GFP_NOFS);
return 0;
}
!isnew && !PageUptodate(page) &&
(block_off_end > to || block_off_start < from) &&
!test_range_bit(tree, block_start, cur_end,
- EXTENT_UPTODATE, 1)) {
+ EXTENT_UPTODATE, 1, NULL)) {
u64 sector;
u64 extent_offset = block_start - em->start;
size_t iosize;
*/
set_extent_bit(tree, block_start,
block_start + iosize - 1,
- EXTENT_LOCKED, 0, NULL, GFP_NOFS);
+ EXTENT_LOCKED, 0, NULL, NULL, GFP_NOFS);
ret = submit_extent_page(READ, tree, page,
sector, iosize, page_offset, em->bdev,
NULL, 1,
int ret = 1;
if (test_range_bit(tree, start, end,
- EXTENT_IOBITS | EXTENT_ORDERED, 0))
+ EXTENT_IOBITS, 0, NULL))
ret = 0;
else {
if ((mask & GFP_NOFS) == GFP_NOFS)
mask = GFP_NOFS;
- clear_extent_bit(tree, start, end, EXTENT_UPTODATE,
- 1, 1, mask);
+ /*
+ * at this point we can safely clear everything except the
+ * locked bit and the nodatasum bit
+ */
+ clear_extent_bit(tree, start, end,
+ ~(EXTENT_LOCKED | EXTENT_NODATASUM),
+ 0, 0, NULL, mask);
}
return ret;
}
u64 len;
while (start <= end) {
len = end - start + 1;
- spin_lock(&map->lock);
+ write_lock(&map->lock);
em = lookup_extent_mapping(map, start, len);
if (!em || IS_ERR(em)) {
- spin_unlock(&map->lock);
+ write_unlock(&map->lock);
break;
}
if (test_bit(EXTENT_FLAG_PINNED, &em->flags) ||
em->start != start) {
- spin_unlock(&map->lock);
+ write_unlock(&map->lock);
free_extent_map(em);
break;
}
if (!test_range_bit(tree, em->start,
extent_map_end(em) - 1,
- EXTENT_LOCKED | EXTENT_WRITEBACK |
- EXTENT_ORDERED,
- 0)) {
+ EXTENT_LOCKED | EXTENT_WRITEBACK,
+ 0, NULL)) {
remove_extent_mapping(map, em);
/* once for the rb tree */
free_extent_map(em);
}
start = extent_map_end(em);
- spin_unlock(&map->lock);
+ write_unlock(&map->lock);
/* once for us */
free_extent_map(em);
int uptodate;
unsigned long index;
- ret = test_range_bit(tree, start, end, EXTENT_UPTODATE, 1);
+ ret = test_range_bit(tree, start, end, EXTENT_UPTODATE, 1, NULL);
if (ret)
return 1;
while (start <= end) {
return 1;
ret = test_range_bit(tree, eb->start, eb->start + eb->len - 1,
- EXTENT_UPTODATE, 1);
+ EXTENT_UPTODATE, 1, NULL);
if (ret)
return ret;
return 0;
if (test_range_bit(tree, eb->start, eb->start + eb->len - 1,
- EXTENT_UPTODATE, 1)) {
+ EXTENT_UPTODATE, 1, NULL)) {
return 0;
}
#define EXTENT_DEFRAG (1 << 6)
#define EXTENT_DEFRAG_DONE (1 << 7)
#define EXTENT_BUFFER_FILLED (1 << 8)
-#define EXTENT_ORDERED (1 << 9)
-#define EXTENT_ORDERED_METADATA (1 << 10)
-#define EXTENT_BOUNDARY (1 << 11)
-#define EXTENT_NODATASUM (1 << 12)
+#define EXTENT_BOUNDARY (1 << 9)
+#define EXTENT_NODATASUM (1 << 10)
#define EXTENT_IOBITS (EXTENT_LOCKED | EXTENT_WRITEBACK)
/* flags for bio submission */
struct extent_state *state, int uptodate);
int (*set_bit_hook)(struct inode *inode, u64 start, u64 end,
unsigned long old, unsigned long bits);
- int (*clear_bit_hook)(struct inode *inode, u64 start, u64 end,
- unsigned long old, unsigned long bits);
+ int (*clear_bit_hook)(struct inode *inode, struct extent_state *state,
+ unsigned long bits);
+ int (*merge_extent_hook)(struct inode *inode,
+ struct extent_state *new,
+ struct extent_state *other);
+ int (*split_extent_hook)(struct inode *inode,
+ struct extent_state *orig, u64 split);
int (*write_cache_pages_lock_hook)(struct page *page);
};
u64 start;
u64 end; /* inclusive */
struct rb_node rb_node;
+
+ /* ADD NEW ELEMENTS AFTER THIS */
struct extent_io_tree *tree;
wait_queue_head_t wq;
atomic_t refs;
unsigned long state;
+ u64 split_start;
+ u64 split_end;
/* for use by the FS */
u64 private;
struct extent_io_tree *tree, struct page *page,
gfp_t mask);
int lock_extent(struct extent_io_tree *tree, u64 start, u64 end, gfp_t mask);
+int lock_extent_bits(struct extent_io_tree *tree, u64 start, u64 end,
+ int bits, struct extent_state **cached, gfp_t mask);
int unlock_extent(struct extent_io_tree *tree, u64 start, u64 end, gfp_t mask);
int try_lock_extent(struct extent_io_tree *tree, u64 start, u64 end,
gfp_t mask);
u64 max_bytes, unsigned long bits);
int test_range_bit(struct extent_io_tree *tree, u64 start, u64 end,
- int bits, int filled);
+ int bits, int filled, struct extent_state *cached_state);
int clear_extent_bits(struct extent_io_tree *tree, u64 start, u64 end,
int bits, gfp_t mask);
int clear_extent_bit(struct extent_io_tree *tree, u64 start, u64 end,
- int bits, int wake, int delete, gfp_t mask);
+ int bits, int wake, int delete, struct extent_state **cached,
+ gfp_t mask);
int set_extent_bits(struct extent_io_tree *tree, u64 start, u64 end,
int bits, gfp_t mask);
int set_extent_uptodate(struct extent_io_tree *tree, u64 start, u64 end,
int clear_unlock,
int clear_delalloc, int clear_dirty,
int set_writeback,
- int end_writeback);
+ int end_writeback,
+ int set_private2);
#endif
void extent_map_tree_init(struct extent_map_tree *tree, gfp_t mask)
{
tree->map.rb_node = NULL;
- spin_lock_init(&tree->lock);
+ rwlock_init(&tree->lock);
}
/**
return 0;
}
+int unpin_extent_cache(struct extent_map_tree *tree, u64 start, u64 len)
+{
+ int ret = 0;
+ struct extent_map *merge = NULL;
+ struct rb_node *rb;
+ struct extent_map *em;
+
+ write_lock(&tree->lock);
+ em = lookup_extent_mapping(tree, start, len);
+
+ WARN_ON(em->start != start || !em);
+
+ if (!em)
+ goto out;
+
+ clear_bit(EXTENT_FLAG_PINNED, &em->flags);
+
+ if (em->start != 0) {
+ rb = rb_prev(&em->rb_node);
+ if (rb)
+ merge = rb_entry(rb, struct extent_map, rb_node);
+ if (rb && mergable_maps(merge, em)) {
+ em->start = merge->start;
+ em->len += merge->len;
+ em->block_len += merge->block_len;
+ em->block_start = merge->block_start;
+ merge->in_tree = 0;
+ rb_erase(&merge->rb_node, &tree->map);
+ free_extent_map(merge);
+ }
+ }
+
+ rb = rb_next(&em->rb_node);
+ if (rb)
+ merge = rb_entry(rb, struct extent_map, rb_node);
+ if (rb && mergable_maps(em, merge)) {
+ em->len += merge->len;
+ em->block_len += merge->len;
+ rb_erase(&merge->rb_node, &tree->map);
+ merge->in_tree = 0;
+ free_extent_map(merge);
+ }
+
+ free_extent_map(em);
+out:
+ write_unlock(&tree->lock);
+ return ret;
+
+}
+
/**
* add_extent_mapping - add new extent map to the extent tree
* @tree: tree to insert new map in
ret = -EEXIST;
goto out;
}
- assert_spin_locked(&tree->lock);
rb = tree_insert(&tree->map, em->start, &em->rb_node);
if (rb) {
ret = -EEXIST;
struct rb_node *next = NULL;
u64 end = range_end(start, len);
- assert_spin_locked(&tree->lock);
rb_node = __tree_search(&tree->map, start, &prev, &next);
if (!rb_node && prev) {
em = rb_entry(prev, struct extent_map, rb_node);
return em;
}
+/**
+ * search_extent_mapping - find a nearby extent map
+ * @tree: tree to lookup in
+ * @start: byte offset to start the search
+ * @len: length of the lookup range
+ *
+ * Find and return the first extent_map struct in @tree that intersects the
+ * [start, len] range.
+ *
+ * If one can't be found, any nearby extent may be returned
+ */
+struct extent_map *search_extent_mapping(struct extent_map_tree *tree,
+ u64 start, u64 len)
+{
+ struct extent_map *em;
+ struct rb_node *rb_node;
+ struct rb_node *prev = NULL;
+ struct rb_node *next = NULL;
+
+ rb_node = __tree_search(&tree->map, start, &prev, &next);
+ if (!rb_node && prev) {
+ em = rb_entry(prev, struct extent_map, rb_node);
+ goto found;
+ }
+ if (!rb_node && next) {
+ em = rb_entry(next, struct extent_map, rb_node);
+ goto found;
+ }
+ if (!rb_node) {
+ em = NULL;
+ goto out;
+ }
+ if (IS_ERR(rb_node)) {
+ em = ERR_PTR(PTR_ERR(rb_node));
+ goto out;
+ }
+ em = rb_entry(rb_node, struct extent_map, rb_node);
+ goto found;
+
+ em = NULL;
+ goto out;
+
+found:
+ atomic_inc(&em->refs);
+out:
+ return em;
+}
+
/**
* remove_extent_mapping - removes an extent_map from the extent tree
* @tree: extent tree to remove from
int ret = 0;
WARN_ON(test_bit(EXTENT_FLAG_PINNED, &em->flags));
- assert_spin_locked(&tree->lock);
rb_erase(&em->rb_node, &tree->map);
em->in_tree = 0;
return ret;
struct extent_map_tree {
struct rb_root map;
- spinlock_t lock;
+ rwlock_t lock;
};
static inline u64 extent_map_end(struct extent_map *em)
void free_extent_map(struct extent_map *em);
int __init extent_map_init(void);
void extent_map_exit(void);
+int unpin_extent_cache(struct extent_map_tree *tree, u64 start, u64 len);
+struct extent_map *search_extent_mapping(struct extent_map_tree *tree,
+ u64 start, u64 len);
#endif
int err = 0;
int i;
struct inode *inode = fdentry(file)->d_inode;
- struct extent_io_tree *io_tree = &BTRFS_I(inode)->io_tree;
- u64 hint_byte;
u64 num_bytes;
u64 start_pos;
u64 end_of_last_block;
root->sectorsize - 1) & ~((u64)root->sectorsize - 1);
end_of_last_block = start_pos + num_bytes - 1;
+ err = btrfs_set_extent_delalloc(inode, start_pos, end_of_last_block);
+ if (err)
+ return err;
- lock_extent(io_tree, start_pos, end_of_last_block, GFP_NOFS);
- trans = btrfs_join_transaction(root, 1);
- if (!trans) {
- err = -ENOMEM;
- goto out_unlock;
- }
- btrfs_set_trans_block_group(trans, inode);
- hint_byte = 0;
-
- set_extent_uptodate(io_tree, start_pos, end_of_last_block, GFP_NOFS);
-
- /* check for reserved extents on each page, we don't want
- * to reset the delalloc bit on things that already have
- * extents reserved.
- */
- btrfs_set_extent_delalloc(inode, start_pos, end_of_last_block);
for (i = 0; i < num_pages; i++) {
struct page *p = pages[i];
SetPageUptodate(p);
* at this time.
*/
}
- err = btrfs_end_transaction(trans, root);
-out_unlock:
- unlock_extent(io_tree, start_pos, end_of_last_block, GFP_NOFS);
return err;
}
if (!split2)
split2 = alloc_extent_map(GFP_NOFS);
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, start, len);
if (!em) {
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
break;
}
flags = em->flags;
if (skip_pinned && test_bit(EXTENT_FLAG_PINNED, &em->flags)) {
- spin_unlock(&em_tree->lock);
if (em->start <= start &&
(!testend || em->start + em->len >= start + len)) {
free_extent_map(em);
+ write_unlock(&em_tree->lock);
break;
}
if (start < em->start) {
start = em->start + em->len;
}
free_extent_map(em);
+ write_unlock(&em_tree->lock);
continue;
}
compressed = test_bit(EXTENT_FLAG_COMPRESSED, &em->flags);
free_extent_map(split);
split = NULL;
}
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
/* once for us */
free_extent_map(em);
noinline int btrfs_drop_extents(struct btrfs_trans_handle *trans,
struct btrfs_root *root, struct inode *inode,
u64 start, u64 end, u64 locked_end,
- u64 inline_limit, u64 *hint_byte)
+ u64 inline_limit, u64 *hint_byte, int drop_cache)
{
u64 extent_end = 0;
u64 search_start = start;
int ret;
inline_limit = 0;
- btrfs_drop_extent_cache(inode, start, end - 1, 0);
+ if (drop_cache)
+ btrfs_drop_extent_cache(inode, start, end - 1, 0);
path = btrfs_alloc_path();
if (!path)
start_pos = pos;
vfs_check_frozen(inode->i_sb, SB_FREEZE_WRITE);
+
+ /* do the reserve before the mutex lock in case we have to do some
+ * flushing. We wouldn't deadlock, but this is more polite.
+ */
+ err = btrfs_reserve_metadata_for_delalloc(root, inode, 1);
+ if (err)
+ goto out_nolock;
+
+ mutex_lock(&inode->i_mutex);
+
current->backing_dev_info = inode->i_mapping->backing_dev_info;
err = generic_write_checks(file, &pos, &count, S_ISBLK(inode->i_mode));
if (err)
- goto out_nolock;
+ goto out;
+
if (count == 0)
- goto out_nolock;
+ goto out;
err = file_remove_suid(file);
if (err)
- goto out_nolock;
+ goto out;
+
file_update_time(file);
pages = kmalloc(nrptrs * sizeof(struct page *), GFP_KERNEL);
- mutex_lock(&inode->i_mutex);
+ /* generic_write_checks can change our pos */
+ start_pos = pos;
+
BTRFS_I(inode)->sequence++;
first_index = pos >> PAGE_CACHE_SHIFT;
last_index = (pos + count) >> PAGE_CACHE_SHIFT;
}
if (will_write) {
- btrfs_fdatawrite_range(inode->i_mapping, pos,
- pos + write_bytes - 1,
- WB_SYNC_ALL);
+ filemap_fdatawrite_range(inode->i_mapping, pos,
+ pos + write_bytes - 1);
} else {
balance_dirty_pages_ratelimited_nr(inode->i_mapping,
num_pages);
mutex_unlock(&inode->i_mutex);
if (ret)
err = ret;
+ btrfs_unreserve_metadata_for_delalloc(root, inode, 1);
out_nolock:
kfree(pages);
return ret > 0 ? EIO : ret;
}
-static struct vm_operations_struct btrfs_file_vm_ops = {
+static const struct vm_operations_struct btrfs_file_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = btrfs_page_mkwrite,
};
return 0;
}
-struct file_operations btrfs_file_operations = {
+const struct file_operations btrfs_file_operations = {
.llseek = generic_file_llseek,
.read = do_sync_read,
.aio_read = generic_file_aio_read,
static void recalculate_thresholds(struct btrfs_block_group_cache *block_group)
{
- u64 max_bytes, possible_bytes;
+ u64 max_bytes;
+ u64 bitmap_bytes;
+ u64 extent_bytes;
/*
* The goal is to keep the total amount of memory used per 1gb of space
max_bytes = MAX_CACHE_BYTES_PER_GIG *
(div64_u64(block_group->key.offset, 1024 * 1024 * 1024));
- possible_bytes = (block_group->total_bitmaps * PAGE_CACHE_SIZE) +
- (sizeof(struct btrfs_free_space) *
- block_group->extents_thresh);
+ /*
+ * we want to account for 1 more bitmap than what we have so we can make
+ * sure we don't go over our overall goal of MAX_CACHE_BYTES_PER_GIG as
+ * we add more bitmaps.
+ */
+ bitmap_bytes = (block_group->total_bitmaps + 1) * PAGE_CACHE_SIZE;
- if (possible_bytes > max_bytes) {
- int extent_bytes = max_bytes -
- (block_group->total_bitmaps * PAGE_CACHE_SIZE);
+ if (bitmap_bytes >= max_bytes) {
+ block_group->extents_thresh = 0;
+ return;
+ }
- if (extent_bytes <= 0) {
- block_group->extents_thresh = 0;
- return;
- }
+ /*
+ * we want the extent entry threshold to always be at most 1/2 the maxw
+ * bytes we can have, or whatever is less than that.
+ */
+ extent_bytes = max_bytes - bitmap_bytes;
+ extent_bytes = min_t(u64, extent_bytes, div64_u64(max_bytes, 2));
- block_group->extents_thresh = extent_bytes /
- (sizeof(struct btrfs_free_space));
- }
+ block_group->extents_thresh =
+ div64_u64(extent_bytes, (sizeof(struct btrfs_free_space)));
}
static void bitmap_clear_bits(struct btrfs_block_group_cache *block_group,
BUG_ON(block_group->total_bitmaps >= max_bitmaps);
info->offset = offset_to_bitmap(block_group, offset);
+ info->bytes = 0;
link_free_space(block_group, info);
block_group->total_bitmaps++;
ptr = (unsigned long)(ref + 1);
ret = 0;
} else if (ret < 0) {
+ if (ret == -EOVERFLOW)
+ ret = -EMLINK;
goto out;
} else {
ref = btrfs_item_ptr(path->nodes[0], path->slots[0],
ret = btrfs_insert_empty_item(trans, root, path, &key,
sizeof(struct btrfs_inode_item));
- if (ret == 0 && objectid > root->highest_inode)
- root->highest_inode = objectid;
return ret;
}
slot = path->slots[0] - 1;
l = path->nodes[0];
btrfs_item_key_to_cpu(l, &found_key, slot);
- *objectid = found_key.objectid;
+ *objectid = max_t(u64, found_key.objectid,
+ BTRFS_FIRST_FREE_OBJECTID - 1);
} else {
- *objectid = BTRFS_FIRST_FREE_OBJECTID;
+ *objectid = BTRFS_FIRST_FREE_OBJECTID - 1;
}
ret = 0;
error:
return ret;
}
-/*
- * walks the btree of allocated inodes and find a hole.
- */
int btrfs_find_free_objectid(struct btrfs_trans_handle *trans,
struct btrfs_root *root,
u64 dirid, u64 *objectid)
{
- struct btrfs_path *path;
- struct btrfs_key key;
int ret;
- int slot = 0;
- u64 last_ino = 0;
- int start_found;
- struct extent_buffer *l;
- struct btrfs_key search_key;
- u64 search_start = dirid;
-
mutex_lock(&root->objectid_mutex);
- if (root->last_inode_alloc >= BTRFS_FIRST_FREE_OBJECTID &&
- root->last_inode_alloc < BTRFS_LAST_FREE_OBJECTID) {
- *objectid = ++root->last_inode_alloc;
- mutex_unlock(&root->objectid_mutex);
- return 0;
- }
- path = btrfs_alloc_path();
- BUG_ON(!path);
- search_start = max(search_start, (u64)BTRFS_FIRST_FREE_OBJECTID);
- search_key.objectid = search_start;
- search_key.type = 0;
- search_key.offset = 0;
-
- start_found = 0;
- ret = btrfs_search_slot(trans, root, &search_key, path, 0, 0);
- if (ret < 0)
- goto error;
- while (1) {
- l = path->nodes[0];
- slot = path->slots[0];
- if (slot >= btrfs_header_nritems(l)) {
- ret = btrfs_next_leaf(root, path);
- if (ret == 0)
- continue;
- if (ret < 0)
- goto error;
- if (!start_found) {
- *objectid = search_start;
- start_found = 1;
- goto found;
- }
- *objectid = last_ino > search_start ?
- last_ino : search_start;
- goto found;
- }
- btrfs_item_key_to_cpu(l, &key, slot);
- if (key.objectid >= search_start) {
- if (start_found) {
- if (last_ino < search_start)
- last_ino = search_start;
- if (key.objectid > last_ino) {
- *objectid = last_ino;
- goto found;
- }
- } else if (key.objectid > search_start) {
- *objectid = search_start;
- goto found;
- }
- }
- if (key.objectid >= BTRFS_LAST_FREE_OBJECTID)
- break;
+ if (unlikely(root->highest_objectid < BTRFS_FIRST_FREE_OBJECTID)) {
+ ret = btrfs_find_highest_inode(root, &root->highest_objectid);
+ if (ret)
+ goto out;
+ }
- start_found = 1;
- last_ino = key.objectid + 1;
- path->slots[0]++;
+ if (unlikely(root->highest_objectid >= BTRFS_LAST_FREE_OBJECTID)) {
+ ret = -ENOSPC;
+ goto out;
}
- BUG_ON(1);
-found:
- btrfs_release_path(root, path);
- btrfs_free_path(path);
- BUG_ON(*objectid < search_start);
- mutex_unlock(&root->objectid_mutex);
- return 0;
-error:
- btrfs_release_path(root, path);
- btrfs_free_path(path);
+
+ *objectid = ++root->highest_objectid;
+ ret = 0;
+out:
mutex_unlock(&root->objectid_mutex);
return ret;
}
static const struct inode_operations btrfs_file_inode_operations;
static const struct address_space_operations btrfs_aops;
static const struct address_space_operations btrfs_symlink_aops;
-static struct file_operations btrfs_dir_file_operations;
+static const struct file_operations btrfs_dir_file_operations;
static struct extent_io_ops btrfs_extent_io_ops;
static struct kmem_cache *btrfs_inode_cachep;
}
ret = btrfs_drop_extents(trans, root, inode, start,
- aligned_end, aligned_end, start, &hint_byte);
+ aligned_end, aligned_end, start,
+ &hint_byte, 1);
BUG_ON(ret);
if (isize > actual_end)
inline_len, compressed_size,
compressed_pages);
BUG_ON(ret);
- btrfs_drop_extent_cache(inode, start, aligned_end, 0);
+ btrfs_drop_extent_cache(inode, start, aligned_end - 1, 0);
return 0;
}
extent_clear_unlock_delalloc(inode,
&BTRFS_I(inode)->io_tree,
start, end, NULL, 1, 0,
- 0, 1, 1, 1);
+ 0, 1, 1, 1, 0);
ret = 0;
goto free_pages_out;
}
set_bit(EXTENT_FLAG_COMPRESSED, &em->flags);
while (1) {
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
if (ret != -EEXIST) {
free_extent_map(em);
break;
async_extent->start,
async_extent->start +
async_extent->ram_size - 1,
- NULL, 1, 1, 0, 1, 1, 0);
+ NULL, 1, 1, 0, 1, 1, 0, 0);
ret = btrfs_submit_compressed_write(inode,
async_extent->start,
extent_clear_unlock_delalloc(inode,
&BTRFS_I(inode)->io_tree,
start, end, NULL, 1, 1,
- 1, 1, 1, 1);
+ 1, 1, 1, 1, 0);
*nr_written = *nr_written +
(end - start + PAGE_CACHE_SIZE) / PAGE_CACHE_SIZE;
*page_started = 1;
BUG_ON(disk_num_bytes >
btrfs_super_total_bytes(&root->fs_info->super_copy));
+
+ read_lock(&BTRFS_I(inode)->extent_tree.lock);
+ em = search_extent_mapping(&BTRFS_I(inode)->extent_tree,
+ start, num_bytes);
+ if (em) {
+ alloc_hint = em->block_start;
+ free_extent_map(em);
+ }
+ read_unlock(&BTRFS_I(inode)->extent_tree.lock);
btrfs_drop_extent_cache(inode, start, start + num_bytes - 1, 0);
while (disk_num_bytes > 0) {
em = alloc_extent_map(GFP_NOFS);
em->start = start;
em->orig_start = em->start;
-
ram_size = ins.offset;
em->len = ins.offset;
set_bit(EXTENT_FLAG_PINNED, &em->flags);
while (1) {
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
if (ret != -EEXIST) {
free_extent_map(em);
break;
/* we're not doing compressed IO, don't unlock the first
* page (which the caller expects to stay locked), don't
* clear any dirty bits and don't set any writeback bits
+ *
+ * Do set the Private2 bit so we know this page was properly
+ * setup for writepage
*/
extent_clear_unlock_delalloc(inode, &BTRFS_I(inode)->io_tree,
start, start + ram_size - 1,
locked_page, unlock, 1,
- 1, 0, 0, 0);
+ 1, 0, 0, 0, 1);
disk_num_bytes -= cur_alloc_size;
num_bytes -= cur_alloc_size;
alloc_hint = ins.objectid + ins.offset;
int limit = 10 * 1024 * 1042;
clear_extent_bit(&BTRFS_I(inode)->io_tree, start, end, EXTENT_LOCKED |
- EXTENT_DELALLOC, 1, 0, GFP_NOFS);
+ EXTENT_DELALLOC, 1, 0, NULL, GFP_NOFS);
while (start < end) {
async_cow = kmalloc(sizeof(*async_cow), GFP_NOFS);
async_cow->inode = inode;
em->bdev = root->fs_info->fs_devices->latest_bdev;
set_bit(EXTENT_FLAG_PINNED, &em->flags);
while (1) {
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
if (ret != -EEXIST) {
free_extent_map(em);
break;
extent_clear_unlock_delalloc(inode, &BTRFS_I(inode)->io_tree,
cur_offset, cur_offset + num_bytes - 1,
- locked_page, 1, 1, 1, 0, 0, 0);
+ locked_page, 1, 1, 1, 0, 0, 0, 1);
cur_offset = extent_end;
if (cur_offset > end)
break;
return ret;
}
+static int btrfs_split_extent_hook(struct inode *inode,
+ struct extent_state *orig, u64 split)
+{
+ struct btrfs_root *root = BTRFS_I(inode)->root;
+ u64 size;
+
+ if (!(orig->state & EXTENT_DELALLOC))
+ return 0;
+
+ size = orig->end - orig->start + 1;
+ if (size > root->fs_info->max_extent) {
+ u64 num_extents;
+ u64 new_size;
+
+ new_size = orig->end - split + 1;
+ num_extents = div64_u64(size + root->fs_info->max_extent - 1,
+ root->fs_info->max_extent);
+
+ /*
+ * if we break a large extent up then leave delalloc_extents be,
+ * since we've already accounted for the large extent.
+ */
+ if (div64_u64(new_size + root->fs_info->max_extent - 1,
+ root->fs_info->max_extent) < num_extents)
+ return 0;
+ }
+
+ BTRFS_I(inode)->delalloc_extents++;
+
+ return 0;
+}
+
+/*
+ * extent_io.c merge_extent_hook, used to track merged delayed allocation
+ * extents so we can keep track of new extents that are just merged onto old
+ * extents, such as when we are doing sequential writes, so we can properly
+ * account for the metadata space we'll need.
+ */
+static int btrfs_merge_extent_hook(struct inode *inode,
+ struct extent_state *new,
+ struct extent_state *other)
+{
+ struct btrfs_root *root = BTRFS_I(inode)->root;
+ u64 new_size, old_size;
+ u64 num_extents;
+
+ /* not delalloc, ignore it */
+ if (!(other->state & EXTENT_DELALLOC))
+ return 0;
+
+ old_size = other->end - other->start + 1;
+ if (new->start < other->start)
+ new_size = other->end - new->start + 1;
+ else
+ new_size = new->end - other->start + 1;
+
+ /* we're not bigger than the max, unreserve the space and go */
+ if (new_size <= root->fs_info->max_extent) {
+ BTRFS_I(inode)->delalloc_extents--;
+ return 0;
+ }
+
+ /*
+ * If we grew by another max_extent, just return, we want to keep that
+ * reserved amount.
+ */
+ num_extents = div64_u64(old_size + root->fs_info->max_extent - 1,
+ root->fs_info->max_extent);
+ if (div64_u64(new_size + root->fs_info->max_extent - 1,
+ root->fs_info->max_extent) > num_extents)
+ return 0;
+
+ BTRFS_I(inode)->delalloc_extents--;
+
+ return 0;
+}
+
/*
* extent_io.c set_bit_hook, used to track delayed allocation
* bytes in this file, and to maintain the list of inodes that
static int btrfs_set_bit_hook(struct inode *inode, u64 start, u64 end,
unsigned long old, unsigned long bits)
{
+
/*
* set_bit and clear bit hooks normally require _irqsave/restore
* but in this case, we are only testeing for the DELALLOC
*/
if (!(old & EXTENT_DELALLOC) && (bits & EXTENT_DELALLOC)) {
struct btrfs_root *root = BTRFS_I(inode)->root;
+
+ BTRFS_I(inode)->delalloc_extents++;
btrfs_delalloc_reserve_space(root, inode, end - start + 1);
spin_lock(&root->fs_info->delalloc_lock);
BTRFS_I(inode)->delalloc_bytes += end - start + 1;
/*
* extent_io.c clear_bit_hook, see set_bit_hook for why
*/
-static int btrfs_clear_bit_hook(struct inode *inode, u64 start, u64 end,
- unsigned long old, unsigned long bits)
+static int btrfs_clear_bit_hook(struct inode *inode,
+ struct extent_state *state, unsigned long bits)
{
/*
* set_bit and clear bit hooks normally require _irqsave/restore
* but in this case, we are only testeing for the DELALLOC
* bit, which is only set or cleared with irqs on
*/
- if ((old & EXTENT_DELALLOC) && (bits & EXTENT_DELALLOC)) {
+ if ((state->state & EXTENT_DELALLOC) && (bits & EXTENT_DELALLOC)) {
struct btrfs_root *root = BTRFS_I(inode)->root;
+ BTRFS_I(inode)->delalloc_extents--;
+ btrfs_unreserve_metadata_for_delalloc(root, inode, 1);
+
spin_lock(&root->fs_info->delalloc_lock);
- if (end - start + 1 > root->fs_info->delalloc_bytes) {
+ if (state->end - state->start + 1 >
+ root->fs_info->delalloc_bytes) {
printk(KERN_INFO "btrfs warning: delalloc account "
"%llu %llu\n",
- (unsigned long long)end - start + 1,
+ (unsigned long long)
+ state->end - state->start + 1,
(unsigned long long)
root->fs_info->delalloc_bytes);
btrfs_delalloc_free_space(root, inode, (u64)-1);
BTRFS_I(inode)->delalloc_bytes = 0;
} else {
btrfs_delalloc_free_space(root, inode,
- end - start + 1);
- root->fs_info->delalloc_bytes -= end - start + 1;
- BTRFS_I(inode)->delalloc_bytes -= end - start + 1;
+ state->end -
+ state->start + 1);
+ root->fs_info->delalloc_bytes -= state->end -
+ state->start + 1;
+ BTRFS_I(inode)->delalloc_bytes -= state->end -
+ state->start + 1;
}
if (BTRFS_I(inode)->delalloc_bytes == 0 &&
!list_empty(&BTRFS_I(inode)->delalloc_inodes)) {
lock_extent(&BTRFS_I(inode)->io_tree, page_start, page_end, GFP_NOFS);
/* already ordered? We're done */
- if (test_range_bit(&BTRFS_I(inode)->io_tree, page_start, page_end,
- EXTENT_ORDERED, 0)) {
+ if (PagePrivate2(page))
goto out;
- }
ordered = btrfs_lookup_ordered_extent(inode, page_start);
if (ordered) {
struct inode *inode = page->mapping->host;
struct btrfs_writepage_fixup *fixup;
struct btrfs_root *root = BTRFS_I(inode)->root;
- int ret;
- ret = test_range_bit(&BTRFS_I(inode)->io_tree, start, end,
- EXTENT_ORDERED, 0);
- if (ret)
+ /* this page is properly in the ordered list */
+ if (TestClearPagePrivate2(page))
return 0;
if (PageChecked(page))
BUG_ON(!path);
path->leave_spinning = 1;
+
+ /*
+ * we may be replacing one extent in the tree with another.
+ * The new extent is pinned in the extent map, and we don't want
+ * to drop it from the cache until it is completely in the btree.
+ *
+ * So, tell btrfs_drop_extents to leave this extent in the cache.
+ * the caller is expected to unpin it and allow it to be merged
+ * with the others.
+ */
ret = btrfs_drop_extents(trans, root, inode, file_pos,
file_pos + num_bytes, locked_end,
- file_pos, &hint);
+ file_pos, &hint, 0);
BUG_ON(ret);
ins.objectid = inode->i_ino;
btrfs_mark_buffer_dirty(leaf);
inode_add_bytes(inode, num_bytes);
- btrfs_drop_extent_cache(inode, file_pos, file_pos + num_bytes - 1, 0);
ins.objectid = disk_bytenr;
ins.offset = disk_num_bytes;
ordered_extent->len,
compressed, 0, 0,
BTRFS_FILE_EXTENT_REG);
+ unpin_extent_cache(&BTRFS_I(inode)->extent_tree,
+ ordered_extent->file_offset,
+ ordered_extent->len);
BUG_ON(ret);
}
unlock_extent(io_tree, ordered_extent->file_offset,
static int btrfs_writepage_end_io_hook(struct page *page, u64 start, u64 end,
struct extent_state *state, int uptodate)
{
+ ClearPagePrivate2(page);
return btrfs_finish_ordered_io(page->mapping->host, start, end);
}
failrec->last_mirror = 0;
failrec->bio_flags = 0;
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, start, failrec->len);
if (em->start > start || em->start + em->len < start) {
free_extent_map(em);
em = NULL;
}
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
if (!em || IS_ERR(em)) {
kfree(failrec);
return 0;
if (root->root_key.objectid == BTRFS_DATA_RELOC_TREE_OBJECTID &&
- test_range_bit(io_tree, start, end, EXTENT_NODATASUM, 1)) {
+ test_range_bit(io_tree, start, end, EXTENT_NODATASUM, 1, NULL)) {
clear_extent_bits(io_tree, start, end, EXTENT_NODATASUM,
GFP_NOFS);
return 0;
return ret;
}
+int btrfs_unlink_subvol(struct btrfs_trans_handle *trans,
+ struct btrfs_root *root,
+ struct inode *dir, u64 objectid,
+ const char *name, int name_len)
+{
+ struct btrfs_path *path;
+ struct extent_buffer *leaf;
+ struct btrfs_dir_item *di;
+ struct btrfs_key key;
+ u64 index;
+ int ret;
+
+ path = btrfs_alloc_path();
+ if (!path)
+ return -ENOMEM;
+
+ di = btrfs_lookup_dir_item(trans, root, path, dir->i_ino,
+ name, name_len, -1);
+ BUG_ON(!di || IS_ERR(di));
+
+ leaf = path->nodes[0];
+ btrfs_dir_item_key_to_cpu(leaf, di, &key);
+ WARN_ON(key.type != BTRFS_ROOT_ITEM_KEY || key.objectid != objectid);
+ ret = btrfs_delete_one_dir_name(trans, root, path, di);
+ BUG_ON(ret);
+ btrfs_release_path(root, path);
+
+ ret = btrfs_del_root_ref(trans, root->fs_info->tree_root,
+ objectid, root->root_key.objectid,
+ dir->i_ino, &index, name, name_len);
+ if (ret < 0) {
+ BUG_ON(ret != -ENOENT);
+ di = btrfs_search_dir_index_item(root, path, dir->i_ino,
+ name, name_len);
+ BUG_ON(!di || IS_ERR(di));
+
+ leaf = path->nodes[0];
+ btrfs_item_key_to_cpu(leaf, &key, path->slots[0]);
+ btrfs_release_path(root, path);
+ index = key.offset;
+ }
+
+ di = btrfs_lookup_dir_index_item(trans, root, path, dir->i_ino,
+ index, name, name_len, -1);
+ BUG_ON(!di || IS_ERR(di));
+
+ leaf = path->nodes[0];
+ btrfs_dir_item_key_to_cpu(leaf, di, &key);
+ WARN_ON(key.type != BTRFS_ROOT_ITEM_KEY || key.objectid != objectid);
+ ret = btrfs_delete_one_dir_name(trans, root, path, di);
+ BUG_ON(ret);
+ btrfs_release_path(root, path);
+
+ btrfs_i_size_write(dir, dir->i_size - name_len * 2);
+ dir->i_mtime = dir->i_ctime = CURRENT_TIME;
+ ret = btrfs_update_inode(trans, root, dir);
+ BUG_ON(ret);
+ dir->i_sb->s_dirt = 1;
+
+ btrfs_free_path(path);
+ return 0;
+}
+
static int btrfs_rmdir(struct inode *dir, struct dentry *dentry)
{
struct inode *inode = dentry->d_inode;
struct btrfs_trans_handle *trans;
unsigned long nr = 0;
- /*
- * the FIRST_FREE_OBJECTID check makes sure we don't try to rmdir
- * the root of a subvolume or snapshot
- */
if (inode->i_size > BTRFS_EMPTY_DIR_SIZE ||
- inode->i_ino == BTRFS_FIRST_FREE_OBJECTID) {
+ inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)
return -ENOTEMPTY;
- }
trans = btrfs_start_transaction(root, 1);
btrfs_set_trans_block_group(trans, dir);
+ if (unlikely(inode->i_ino == BTRFS_EMPTY_SUBVOL_DIR_OBJECTID)) {
+ err = btrfs_unlink_subvol(trans, root, dir,
+ BTRFS_I(inode)->location.objectid,
+ dentry->d_name.name,
+ dentry->d_name.len);
+ goto out;
+ }
+
err = btrfs_orphan_add(trans, inode);
if (err)
- goto fail_trans;
+ goto out;
/* now the directory is empty */
err = btrfs_unlink_inode(trans, root, dir, dentry->d_inode,
dentry->d_name.name, dentry->d_name.len);
if (!err)
btrfs_i_size_write(inode, 0);
-
-fail_trans:
+out:
nr = trans->blocks_used;
ret = btrfs_end_transaction_throttle(trans, root);
btrfs_btree_balance_dirty(root, nr);
goto again;
}
- btrfs_set_extent_delalloc(inode, page_start, page_end);
+ ret = btrfs_set_extent_delalloc(inode, page_start, page_end);
+ if (ret) {
+ unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
+ goto out_unlock;
+ }
+
ret = 0;
if (offset != PAGE_CACHE_SIZE) {
kaddr = kmap(page);
u64 last_byte;
u64 cur_offset;
u64 hole_size;
- int err;
+ int err = 0;
if (size <= hole_start)
return 0;
- err = btrfs_check_metadata_free_space(root);
- if (err)
- return err;
-
btrfs_truncate_page(inode->i_mapping, inode->i_size);
while (1) {
cur_offset,
cur_offset + hole_size,
block_end,
- cur_offset, &hint_byte);
+ cur_offset, &hint_byte, 1);
if (err)
break;
+
+ err = btrfs_reserve_metadata_space(root, 1);
+ if (err)
+ break;
+
err = btrfs_insert_file_extent(trans, root,
inode->i_ino, cur_offset, 0,
0, hole_size, 0, hole_size,
0, 0, 0);
btrfs_drop_extent_cache(inode, hole_start,
last_byte - 1, 0);
+ btrfs_unreserve_metadata_space(root, 1);
}
free_extent_map(em);
cur_offset = last_byte;
}
btrfs_wait_ordered_range(inode, 0, (u64)-1);
+ if (inode->i_nlink > 0) {
+ BUG_ON(btrfs_root_refs(&root->root_item) != 0);
+ goto no_delete;
+ }
+
btrfs_i_size_write(inode, 0);
trans = btrfs_join_transaction(root, 1);
* is kind of like crossing a mount point.
*/
static int fixup_tree_root_location(struct btrfs_root *root,
- struct btrfs_key *location,
- struct btrfs_root **sub_root,
- struct dentry *dentry)
+ struct inode *dir,
+ struct dentry *dentry,
+ struct btrfs_key *location,
+ struct btrfs_root **sub_root)
{
- struct btrfs_root_item *ri;
+ struct btrfs_path *path;
+ struct btrfs_root *new_root;
+ struct btrfs_root_ref *ref;
+ struct extent_buffer *leaf;
+ int ret;
+ int err = 0;
- if (btrfs_key_type(location) != BTRFS_ROOT_ITEM_KEY)
- return 0;
- if (location->objectid == BTRFS_ROOT_TREE_OBJECTID)
- return 0;
+ path = btrfs_alloc_path();
+ if (!path) {
+ err = -ENOMEM;
+ goto out;
+ }
- *sub_root = btrfs_read_fs_root(root->fs_info, location,
- dentry->d_name.name,
- dentry->d_name.len);
- if (IS_ERR(*sub_root))
- return PTR_ERR(*sub_root);
+ err = -ENOENT;
+ ret = btrfs_find_root_ref(root->fs_info->tree_root, path,
+ BTRFS_I(dir)->root->root_key.objectid,
+ location->objectid);
+ if (ret) {
+ if (ret < 0)
+ err = ret;
+ goto out;
+ }
- ri = &(*sub_root)->root_item;
- location->objectid = btrfs_root_dirid(ri);
- btrfs_set_key_type(location, BTRFS_INODE_ITEM_KEY);
- location->offset = 0;
+ leaf = path->nodes[0];
+ ref = btrfs_item_ptr(leaf, path->slots[0], struct btrfs_root_ref);
+ if (btrfs_root_ref_dirid(leaf, ref) != dir->i_ino ||
+ btrfs_root_ref_name_len(leaf, ref) != dentry->d_name.len)
+ goto out;
- return 0;
+ ret = memcmp_extent_buffer(leaf, dentry->d_name.name,
+ (unsigned long)(ref + 1),
+ dentry->d_name.len);
+ if (ret)
+ goto out;
+
+ btrfs_release_path(root->fs_info->tree_root, path);
+
+ new_root = btrfs_read_fs_root_no_name(root->fs_info, location);
+ if (IS_ERR(new_root)) {
+ err = PTR_ERR(new_root);
+ goto out;
+ }
+
+ if (btrfs_root_refs(&new_root->root_item) == 0) {
+ err = -ENOENT;
+ goto out;
+ }
+
+ *sub_root = new_root;
+ location->objectid = btrfs_root_dirid(&new_root->root_item);
+ location->type = BTRFS_INODE_ITEM_KEY;
+ location->offset = 0;
+ err = 0;
+out:
+ btrfs_free_path(path);
+ return err;
}
static void inode_tree_add(struct inode *inode)
struct btrfs_inode *entry;
struct rb_node **p;
struct rb_node *parent;
-
again:
p = &root->inode_tree.rb_node;
parent = NULL;
+ if (hlist_unhashed(&inode->i_hash))
+ return;
+
spin_lock(&root->inode_lock);
while (*p) {
parent = *p;
static void inode_tree_del(struct inode *inode)
{
struct btrfs_root *root = BTRFS_I(inode)->root;
+ int empty = 0;
spin_lock(&root->inode_lock);
if (!RB_EMPTY_NODE(&BTRFS_I(inode)->rb_node)) {
rb_erase(&BTRFS_I(inode)->rb_node, &root->inode_tree);
RB_CLEAR_NODE(&BTRFS_I(inode)->rb_node);
+ empty = RB_EMPTY_ROOT(&root->inode_tree);
+ }
+ spin_unlock(&root->inode_lock);
+
+ if (empty && btrfs_root_refs(&root->root_item) == 0) {
+ synchronize_srcu(&root->fs_info->subvol_srcu);
+ spin_lock(&root->inode_lock);
+ empty = RB_EMPTY_ROOT(&root->inode_tree);
+ spin_unlock(&root->inode_lock);
+ if (empty)
+ btrfs_add_dead_root(root);
+ }
+}
+
+int btrfs_invalidate_inodes(struct btrfs_root *root)
+{
+ struct rb_node *node;
+ struct rb_node *prev;
+ struct btrfs_inode *entry;
+ struct inode *inode;
+ u64 objectid = 0;
+
+ WARN_ON(btrfs_root_refs(&root->root_item) != 0);
+
+ spin_lock(&root->inode_lock);
+again:
+ node = root->inode_tree.rb_node;
+ prev = NULL;
+ while (node) {
+ prev = node;
+ entry = rb_entry(node, struct btrfs_inode, rb_node);
+
+ if (objectid < entry->vfs_inode.i_ino)
+ node = node->rb_left;
+ else if (objectid > entry->vfs_inode.i_ino)
+ node = node->rb_right;
+ else
+ break;
+ }
+ if (!node) {
+ while (prev) {
+ entry = rb_entry(prev, struct btrfs_inode, rb_node);
+ if (objectid <= entry->vfs_inode.i_ino) {
+ node = prev;
+ break;
+ }
+ prev = rb_next(prev);
+ }
+ }
+ while (node) {
+ entry = rb_entry(node, struct btrfs_inode, rb_node);
+ objectid = entry->vfs_inode.i_ino + 1;
+ inode = igrab(&entry->vfs_inode);
+ if (inode) {
+ spin_unlock(&root->inode_lock);
+ if (atomic_read(&inode->i_count) > 1)
+ d_prune_aliases(inode);
+ /*
+ * btrfs_drop_inode will remove it from
+ * the inode cache when its usage count
+ * hits zero.
+ */
+ iput(inode);
+ cond_resched();
+ spin_lock(&root->inode_lock);
+ goto again;
+ }
+
+ if (cond_resched_lock(&root->inode_lock))
+ goto again;
+
+ node = rb_next(node);
}
spin_unlock(&root->inode_lock);
+ return 0;
}
static noinline void init_btrfs_i(struct inode *inode)
return inode;
}
+static struct inode *new_simple_dir(struct super_block *s,
+ struct btrfs_key *key,
+ struct btrfs_root *root)
+{
+ struct inode *inode = new_inode(s);
+
+ if (!inode)
+ return ERR_PTR(-ENOMEM);
+
+ init_btrfs_i(inode);
+
+ BTRFS_I(inode)->root = root;
+ memcpy(&BTRFS_I(inode)->location, key, sizeof(*key));
+ BTRFS_I(inode)->dummy_inode = 1;
+
+ inode->i_ino = BTRFS_EMPTY_SUBVOL_DIR_OBJECTID;
+ inode->i_op = &simple_dir_inode_operations;
+ inode->i_fop = &simple_dir_operations;
+ inode->i_mode = S_IFDIR | S_IRUGO | S_IWUSR | S_IXUGO;
+ inode->i_mtime = inode->i_atime = inode->i_ctime = CURRENT_TIME;
+
+ return inode;
+}
+
struct inode *btrfs_lookup_dentry(struct inode *dir, struct dentry *dentry)
{
struct inode *inode;
- struct btrfs_inode *bi = BTRFS_I(dir);
- struct btrfs_root *root = bi->root;
+ struct btrfs_root *root = BTRFS_I(dir)->root;
struct btrfs_root *sub_root = root;
struct btrfs_key location;
+ int index;
int ret;
+ dentry->d_op = &btrfs_dentry_operations;
+
if (dentry->d_name.len > BTRFS_NAME_LEN)
return ERR_PTR(-ENAMETOOLONG);
if (ret < 0)
return ERR_PTR(ret);
- inode = NULL;
- if (location.objectid) {
- ret = fixup_tree_root_location(root, &location, &sub_root,
- dentry);
- if (ret < 0)
- return ERR_PTR(ret);
- if (ret > 0)
- return ERR_PTR(-ENOENT);
+ if (location.objectid == 0)
+ return NULL;
+
+ if (location.type == BTRFS_INODE_ITEM_KEY) {
+ inode = btrfs_iget(dir->i_sb, &location, root);
+ return inode;
+ }
+
+ BUG_ON(location.type != BTRFS_ROOT_ITEM_KEY);
+
+ index = srcu_read_lock(&root->fs_info->subvol_srcu);
+ ret = fixup_tree_root_location(root, dir, dentry,
+ &location, &sub_root);
+ if (ret < 0) {
+ if (ret != -ENOENT)
+ inode = ERR_PTR(ret);
+ else
+ inode = new_simple_dir(dir->i_sb, &location, sub_root);
+ } else {
inode = btrfs_iget(dir->i_sb, &location, sub_root);
- if (IS_ERR(inode))
- return ERR_CAST(inode);
}
+ srcu_read_unlock(&root->fs_info->subvol_srcu, index);
+
return inode;
}
+static int btrfs_dentry_delete(struct dentry *dentry)
+{
+ struct btrfs_root *root;
+
+ if (!dentry->d_inode)
+ return 0;
+
+ root = BTRFS_I(dentry->d_inode)->root;
+ if (btrfs_root_refs(&root->root_item) == 0)
+ return 1;
+ return 0;
+}
+
static struct dentry *btrfs_lookup(struct inode *dir, struct dentry *dentry,
struct nameidata *nd)
{
struct inode *inode;
- if (dentry->d_name.len > BTRFS_NAME_LEN)
- return ERR_PTR(-ENAMETOOLONG);
-
inode = btrfs_lookup_dentry(dir, dentry);
if (IS_ERR(inode))
return ERR_CAST(inode);
if (ret != 0)
goto fail;
- if (objectid > root->highest_inode)
- root->highest_inode = objectid;
-
inode->i_uid = current_fsuid();
if (dir && (dir->i_mode & S_ISGID)) {
struct inode *parent_inode, struct inode *inode,
const char *name, int name_len, int add_backref, u64 index)
{
- int ret;
+ int ret = 0;
struct btrfs_key key;
struct btrfs_root *root = BTRFS_I(parent_inode)->root;
- key.objectid = inode->i_ino;
- btrfs_set_key_type(&key, BTRFS_INODE_ITEM_KEY);
- key.offset = 0;
+ if (unlikely(inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)) {
+ memcpy(&key, &BTRFS_I(inode)->root->root_key, sizeof(key));
+ } else {
+ key.objectid = inode->i_ino;
+ btrfs_set_key_type(&key, BTRFS_INODE_ITEM_KEY);
+ key.offset = 0;
+ }
+
+ if (unlikely(inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)) {
+ ret = btrfs_add_root_ref(trans, root->fs_info->tree_root,
+ key.objectid, root->root_key.objectid,
+ parent_inode->i_ino,
+ index, name, name_len);
+ } else if (add_backref) {
+ ret = btrfs_insert_inode_ref(trans, root,
+ name, name_len, inode->i_ino,
+ parent_inode->i_ino, index);
+ }
- ret = btrfs_insert_dir_item(trans, root, name, name_len,
- parent_inode->i_ino,
- &key, btrfs_inode_type(inode),
- index);
if (ret == 0) {
- if (add_backref) {
- ret = btrfs_insert_inode_ref(trans, root,
- name, name_len,
- inode->i_ino,
- parent_inode->i_ino,
- index);
- }
+ ret = btrfs_insert_dir_item(trans, root, name, name_len,
+ parent_inode->i_ino, &key,
+ btrfs_inode_type(inode), index);
+ BUG_ON(ret);
+
btrfs_i_size_write(parent_inode, parent_inode->i_size +
name_len * 2);
parent_inode->i_mtime = parent_inode->i_ctime = CURRENT_TIME;
if (!new_valid_dev(rdev))
return -EINVAL;
- err = btrfs_check_metadata_free_space(root);
+ /*
+ * 2 for inode item and ref
+ * 2 for dir items
+ * 1 for xattr if selinux is on
+ */
+ err = btrfs_reserve_metadata_space(root, 5);
if (err)
- goto fail;
+ return err;
trans = btrfs_start_transaction(root, 1);
+ if (!trans)
+ goto fail;
btrfs_set_trans_block_group(trans, dir);
err = btrfs_find_free_objectid(trans, root, dir->i_ino, &objectid);
nr = trans->blocks_used;
btrfs_end_transaction_throttle(trans, root);
fail:
+ btrfs_unreserve_metadata_space(root, 5);
if (drop_inode) {
inode_dec_link_count(inode);
iput(inode);
u64 objectid;
u64 index = 0;
- err = btrfs_check_metadata_free_space(root);
+ /*
+ * 2 for inode item and ref
+ * 2 for dir items
+ * 1 for xattr if selinux is on
+ */
+ err = btrfs_reserve_metadata_space(root, 5);
if (err)
- goto fail;
+ return err;
+
trans = btrfs_start_transaction(root, 1);
+ if (!trans)
+ goto fail;
btrfs_set_trans_block_group(trans, dir);
err = btrfs_find_free_objectid(trans, root, dir->i_ino, &objectid);
nr = trans->blocks_used;
btrfs_end_transaction_throttle(trans, root);
fail:
+ btrfs_unreserve_metadata_space(root, 5);
if (drop_inode) {
inode_dec_link_count(inode);
iput(inode);
if (inode->i_nlink == 0)
return -ENOENT;
- btrfs_inc_nlink(inode);
- err = btrfs_check_metadata_free_space(root);
+ /*
+ * 1 item for inode ref
+ * 2 items for dir items
+ */
+ err = btrfs_reserve_metadata_space(root, 3);
if (err)
- goto fail;
+ return err;
+
+ btrfs_inc_nlink(inode);
+
err = btrfs_set_inode_index(dir, &index);
if (err)
goto fail;
err = btrfs_add_nondir(trans, dentry, inode, 1, index);
- if (err)
- drop_inode = 1;
-
- btrfs_update_inode_block_group(trans, dir);
- err = btrfs_update_inode(trans, root, inode);
-
- if (err)
+ if (err) {
drop_inode = 1;
+ } else {
+ btrfs_update_inode_block_group(trans, dir);
+ err = btrfs_update_inode(trans, root, inode);
+ BUG_ON(err);
+ btrfs_log_new_name(trans, inode, NULL, dentry->d_parent);
+ }
nr = trans->blocks_used;
-
- btrfs_log_new_name(trans, inode, NULL, dentry->d_parent);
btrfs_end_transaction_throttle(trans, root);
fail:
+ btrfs_unreserve_metadata_space(root, 3);
if (drop_inode) {
inode_dec_link_count(inode);
iput(inode);
u64 index = 0;
unsigned long nr = 1;
- err = btrfs_check_metadata_free_space(root);
+ /*
+ * 2 items for inode and ref
+ * 2 items for dir items
+ * 1 for xattr if selinux is on
+ */
+ err = btrfs_reserve_metadata_space(root, 5);
if (err)
- goto out_unlock;
+ return err;
trans = btrfs_start_transaction(root, 1);
- btrfs_set_trans_block_group(trans, dir);
-
- if (IS_ERR(trans)) {
- err = PTR_ERR(trans);
+ if (!trans) {
+ err = -ENOMEM;
goto out_unlock;
}
+ btrfs_set_trans_block_group(trans, dir);
err = btrfs_find_free_objectid(trans, root, dir->i_ino, &objectid);
if (err) {
btrfs_end_transaction_throttle(trans, root);
out_unlock:
+ btrfs_unreserve_metadata_space(root, 5);
if (drop_on_err)
iput(inode);
btrfs_btree_balance_dirty(root, nr);
int compressed;
again:
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, start, len);
if (em)
em->bdev = root->fs_info->fs_devices->latest_bdev;
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
if (em) {
if (em->start > start || em->start + em->len <= start)
map = kmap(page);
read_extent_buffer(leaf, map + pg_offset, ptr,
copy_size);
+ if (pg_offset + copy_size < PAGE_CACHE_SIZE) {
+ memset(map + pg_offset + copy_size, 0,
+ PAGE_CACHE_SIZE - pg_offset -
+ copy_size);
+ }
kunmap(page);
}
flush_dcache_page(page);
}
err = 0;
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
/* it is possible that someone inserted the extent into the tree
* while we had the lock dropped. It is also possible that
err = 0;
}
}
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
out:
if (path)
btrfs_free_path(path);
u64 page_start = page_offset(page);
u64 page_end = page_start + PAGE_CACHE_SIZE - 1;
+
+ /*
+ * we have the page locked, so new writeback can't start,
+ * and the dirty bit won't be cleared while we are here.
+ *
+ * Wait for IO on this page so that we can safely clear
+ * the PagePrivate2 bit and do ordered accounting
+ */
wait_on_page_writeback(page);
+
tree = &BTRFS_I(page->mapping->host)->io_tree;
if (offset) {
btrfs_releasepage(page, GFP_NOFS);
return;
}
-
lock_extent(tree, page_start, page_end, GFP_NOFS);
ordered = btrfs_lookup_ordered_extent(page->mapping->host,
page_offset(page));
*/
clear_extent_bit(tree, page_start, page_end,
EXTENT_DIRTY | EXTENT_DELALLOC |
- EXTENT_LOCKED, 1, 0, GFP_NOFS);
- btrfs_finish_ordered_io(page->mapping->host,
- page_start, page_end);
+ EXTENT_LOCKED, 1, 0, NULL, GFP_NOFS);
+ /*
+ * whoever cleared the private bit is responsible
+ * for the finish_ordered_io
+ */
+ if (TestClearPagePrivate2(page)) {
+ btrfs_finish_ordered_io(page->mapping->host,
+ page_start, page_end);
+ }
btrfs_put_ordered_extent(ordered);
lock_extent(tree, page_start, page_end, GFP_NOFS);
}
clear_extent_bit(tree, page_start, page_end,
- EXTENT_LOCKED | EXTENT_DIRTY | EXTENT_DELALLOC |
- EXTENT_ORDERED,
- 1, 1, GFP_NOFS);
+ EXTENT_LOCKED | EXTENT_DIRTY | EXTENT_DELALLOC,
+ 1, 1, NULL, GFP_NOFS);
__btrfs_releasepage(page, GFP_NOFS);
ClearPageChecked(page);
goto out;
}
+ ret = btrfs_reserve_metadata_for_delalloc(root, inode, 1);
+ if (ret) {
+ btrfs_free_reserved_data_space(root, inode, PAGE_CACHE_SIZE);
+ ret = VM_FAULT_SIGBUS;
+ goto out;
+ }
+
ret = VM_FAULT_NOPAGE; /* make the VM retry the fault */
again:
lock_page(page);
goto again;
}
- btrfs_set_extent_delalloc(inode, page_start, page_end);
+ /*
+ * XXX - page_mkwrite gets called every time the page is dirtied, even
+ * if it was already dirty, so for space accounting reasons we need to
+ * clear any delalloc bits for the range we are fixing to save. There
+ * is probably a better way to do this, but for now keep consistent with
+ * prepare_pages in the normal write path.
+ */
+ clear_extent_bits(&BTRFS_I(inode)->io_tree, page_start, page_end,
+ EXTENT_DIRTY | EXTENT_DELALLOC, GFP_NOFS);
+
+ ret = btrfs_set_extent_delalloc(inode, page_start, page_end);
+ if (ret) {
+ unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
+ ret = VM_FAULT_SIGBUS;
+ btrfs_free_reserved_data_space(root, inode, PAGE_CACHE_SIZE);
+ goto out_unlock;
+ }
ret = 0;
/* page is wholly or partially inside EOF */
}
ClearPageChecked(page);
set_page_dirty(page);
+ SetPageUptodate(page);
BTRFS_I(inode)->last_trans = root->fs_info->generation + 1;
unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
out_unlock:
+ btrfs_unreserve_metadata_for_delalloc(root, inode, 1);
+ if (!ret)
+ return VM_FAULT_LOCKED;
unlock_page(page);
out:
return ret;
* create a new subvolume directory/inode (helper for the ioctl).
*/
int btrfs_create_subvol_root(struct btrfs_trans_handle *trans,
- struct btrfs_root *new_root, struct dentry *dentry,
+ struct btrfs_root *new_root,
u64 new_dirid, u64 alloc_hint)
{
struct inode *inode;
- int error;
+ int err;
u64 index = 0;
inode = btrfs_new_inode(trans, new_root, NULL, "..", 2, new_dirid,
inode->i_nlink = 1;
btrfs_i_size_write(inode, 0);
- error = btrfs_update_inode(trans, new_root, inode);
- if (error)
- return error;
+ err = btrfs_update_inode(trans, new_root, inode);
+ BUG_ON(err);
- d_instantiate(dentry, inode);
+ iput(inode);
return 0;
}
return NULL;
ei->last_trans = 0;
ei->logged_trans = 0;
+ ei->delalloc_extents = 0;
+ ei->delalloc_reserved_extents = 0;
btrfs_ordered_inode_tree_init(&ei->ordered_tree);
INIT_LIST_HEAD(&ei->i_orphan);
INIT_LIST_HEAD(&ei->ordered_operations);
kmem_cache_free(btrfs_inode_cachep, BTRFS_I(inode));
}
+void btrfs_drop_inode(struct inode *inode)
+{
+ struct btrfs_root *root = BTRFS_I(inode)->root;
+
+ if (inode->i_nlink > 0 && btrfs_root_refs(&root->root_item) == 0)
+ generic_delete_inode(inode);
+ else
+ generic_drop_inode(inode);
+}
+
static void init_once(void *foo)
{
struct btrfs_inode *ei = (struct btrfs_inode *) foo;
{
struct btrfs_trans_handle *trans;
struct btrfs_root *root = BTRFS_I(old_dir)->root;
+ struct btrfs_root *dest = BTRFS_I(new_dir)->root;
struct inode *new_inode = new_dentry->d_inode;
struct inode *old_inode = old_dentry->d_inode;
struct timespec ctime = CURRENT_TIME;
u64 index = 0;
+ u64 root_objectid;
int ret;
- /* we're not allowed to rename between subvolumes */
- if (BTRFS_I(old_inode)->root->root_key.objectid !=
- BTRFS_I(new_dir)->root->root_key.objectid)
+ if (new_dir->i_ino == BTRFS_EMPTY_SUBVOL_DIR_OBJECTID)
+ return -EPERM;
+
+ /* we only allow rename subvolume link between subvolumes */
+ if (old_inode->i_ino != BTRFS_FIRST_FREE_OBJECTID && root != dest)
return -EXDEV;
+ if (old_inode->i_ino == BTRFS_EMPTY_SUBVOL_DIR_OBJECTID ||
+ (new_inode && new_inode->i_ino == BTRFS_FIRST_FREE_OBJECTID))
+ return -ENOTEMPTY;
+
if (S_ISDIR(old_inode->i_mode) && new_inode &&
- new_inode->i_size > BTRFS_EMPTY_DIR_SIZE) {
+ new_inode->i_size > BTRFS_EMPTY_DIR_SIZE)
return -ENOTEMPTY;
- }
- /* to rename a snapshot or subvolume, we need to juggle the
- * backrefs. This isn't coded yet
+ /*
+ * 2 items for dir items
+ * 1 item for orphan entry
+ * 1 item for ref
*/
- if (old_inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)
- return -EXDEV;
-
- ret = btrfs_check_metadata_free_space(root);
+ ret = btrfs_reserve_metadata_space(root, 4);
if (ret)
- goto out_unlock;
+ return ret;
/*
* we're using rename to replace one file with another.
old_inode->i_size > BTRFS_ORDERED_OPERATIONS_FLUSH_LIMIT)
filemap_flush(old_inode->i_mapping);
+ /* close the racy window with snapshot create/destroy ioctl */
+ if (old_inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)
+ down_read(&root->fs_info->subvol_sem);
+
trans = btrfs_start_transaction(root, 1);
+ btrfs_set_trans_block_group(trans, new_dir);
+
+ if (dest != root)
+ btrfs_record_root_in_trans(trans, dest);
+
+ ret = btrfs_set_inode_index(new_dir, &index);
+ if (ret)
+ goto out_fail;
+ if (unlikely(old_inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)) {
+ /* force full log commit if subvolume involved. */
+ root->fs_info->last_trans_log_full_commit = trans->transid;
+ } else {
+ ret = btrfs_insert_inode_ref(trans, dest,
+ new_dentry->d_name.name,
+ new_dentry->d_name.len,
+ old_inode->i_ino,
+ new_dir->i_ino, index);
+ if (ret)
+ goto out_fail;
+ /*
+ * this is an ugly little race, but the rename is required
+ * to make sure that if we crash, the inode is either at the
+ * old name or the new one. pinning the log transaction lets
+ * us make sure we don't allow a log commit to come in after
+ * we unlink the name but before we add the new name back in.
+ */
+ btrfs_pin_log_trans(root);
+ }
/*
* make sure the inode gets flushed if it is replacing
* something.
btrfs_add_ordered_operation(trans, root, old_inode);
}
- /*
- * this is an ugly little race, but the rename is required to make
- * sure that if we crash, the inode is either at the old name
- * or the new one. pinning the log transaction lets us make sure
- * we don't allow a log commit to come in after we unlink the
- * name but before we add the new name back in.
- */
- btrfs_pin_log_trans(root);
-
- btrfs_set_trans_block_group(trans, new_dir);
-
- btrfs_inc_nlink(old_dentry->d_inode);
old_dir->i_ctime = old_dir->i_mtime = ctime;
new_dir->i_ctime = new_dir->i_mtime = ctime;
old_inode->i_ctime = ctime;
if (old_dentry->d_parent != new_dentry->d_parent)
btrfs_record_unlink_dir(trans, old_dir, old_inode, 1);
- ret = btrfs_unlink_inode(trans, root, old_dir, old_dentry->d_inode,
- old_dentry->d_name.name,
- old_dentry->d_name.len);
- if (ret)
- goto out_fail;
+ if (unlikely(old_inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)) {
+ root_objectid = BTRFS_I(old_inode)->root->root_key.objectid;
+ ret = btrfs_unlink_subvol(trans, root, old_dir, root_objectid,
+ old_dentry->d_name.name,
+ old_dentry->d_name.len);
+ } else {
+ btrfs_inc_nlink(old_dentry->d_inode);
+ ret = btrfs_unlink_inode(trans, root, old_dir,
+ old_dentry->d_inode,
+ old_dentry->d_name.name,
+ old_dentry->d_name.len);
+ }
+ BUG_ON(ret);
if (new_inode) {
new_inode->i_ctime = CURRENT_TIME;
- ret = btrfs_unlink_inode(trans, root, new_dir,
- new_dentry->d_inode,
- new_dentry->d_name.name,
- new_dentry->d_name.len);
- if (ret)
- goto out_fail;
+ if (unlikely(new_inode->i_ino ==
+ BTRFS_EMPTY_SUBVOL_DIR_OBJECTID)) {
+ root_objectid = BTRFS_I(new_inode)->location.objectid;
+ ret = btrfs_unlink_subvol(trans, dest, new_dir,
+ root_objectid,
+ new_dentry->d_name.name,
+ new_dentry->d_name.len);
+ BUG_ON(new_inode->i_nlink == 0);
+ } else {
+ ret = btrfs_unlink_inode(trans, dest, new_dir,
+ new_dentry->d_inode,
+ new_dentry->d_name.name,
+ new_dentry->d_name.len);
+ }
+ BUG_ON(ret);
if (new_inode->i_nlink == 0) {
ret = btrfs_orphan_add(trans, new_dentry->d_inode);
- if (ret)
- goto out_fail;
+ BUG_ON(ret);
}
-
}
- ret = btrfs_set_inode_index(new_dir, &index);
- if (ret)
- goto out_fail;
- ret = btrfs_add_link(trans, new_dentry->d_parent->d_inode,
- old_inode, new_dentry->d_name.name,
- new_dentry->d_name.len, 1, index);
- if (ret)
- goto out_fail;
+ ret = btrfs_add_link(trans, new_dir, old_inode,
+ new_dentry->d_name.name,
+ new_dentry->d_name.len, 0, index);
+ BUG_ON(ret);
- btrfs_log_new_name(trans, old_inode, old_dir,
- new_dentry->d_parent);
+ if (old_inode->i_ino != BTRFS_FIRST_FREE_OBJECTID) {
+ btrfs_log_new_name(trans, old_inode, old_dir,
+ new_dentry->d_parent);
+ btrfs_end_log_trans(root);
+ }
out_fail:
-
- /* this btrfs_end_log_trans just allows the current
- * log-sub transaction to complete
- */
- btrfs_end_log_trans(root);
btrfs_end_transaction_throttle(trans, root);
-out_unlock:
+
+ if (old_inode->i_ino == BTRFS_FIRST_FREE_OBJECTID)
+ up_read(&root->fs_info->subvol_sem);
+
+ btrfs_unreserve_metadata_space(root, 4);
return ret;
}
if (name_len > BTRFS_MAX_INLINE_DATA_SIZE(root))
return -ENAMETOOLONG;
- err = btrfs_check_metadata_free_space(root);
+ /*
+ * 2 items for inode item and ref
+ * 2 items for dir items
+ * 1 item for xattr if selinux is on
+ */
+ err = btrfs_reserve_metadata_space(root, 5);
if (err)
- goto out_fail;
+ return err;
trans = btrfs_start_transaction(root, 1);
+ if (!trans)
+ goto out_fail;
btrfs_set_trans_block_group(trans, dir);
err = btrfs_find_free_objectid(trans, root, dir->i_ino, &objectid);
nr = trans->blocks_used;
btrfs_end_transaction_throttle(trans, root);
out_fail:
+ btrfs_unreserve_metadata_space(root, 5);
if (drop_inode) {
inode_dec_link_count(inode);
iput(inode);
while (num_bytes > 0) {
alloc_size = min(num_bytes, root->fs_info->max_extent);
+
+ ret = btrfs_reserve_metadata_space(root, 1);
+ if (ret)
+ goto out;
+
ret = btrfs_reserve_extent(trans, root, alloc_size,
root->sectorsize, 0, alloc_hint,
(u64)-1, &ins, 1);
0, 0, 0,
BTRFS_FILE_EXTENT_PREALLOC);
BUG_ON(ret);
+ btrfs_drop_extent_cache(inode, cur_offset,
+ cur_offset + ins.offset -1, 0);
num_bytes -= ins.offset;
cur_offset += ins.offset;
alloc_hint = ins.objectid + ins.offset;
+ btrfs_unreserve_metadata_space(root, 1);
}
out:
if (cur_offset > start) {
.lookup = btrfs_lookup,
.permission = btrfs_permission,
};
-static struct file_operations btrfs_dir_file_operations = {
+
+static const struct file_operations btrfs_dir_file_operations = {
.llseek = generic_file_llseek,
.read = generic_read_dir,
.readdir = btrfs_real_readdir,
.readpage_io_failed_hook = btrfs_io_failed_hook,
.set_bit_hook = btrfs_set_bit_hook,
.clear_bit_hook = btrfs_clear_bit_hook,
+ .merge_extent_hook = btrfs_merge_extent_hook,
+ .split_extent_hook = btrfs_split_extent_hook,
};
/*
.invalidatepage = btrfs_invalidatepage,
.releasepage = btrfs_releasepage,
.set_page_dirty = btrfs_set_page_dirty,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations btrfs_symlink_aops = {
.listxattr = btrfs_listxattr,
.removexattr = btrfs_removexattr,
};
+
+struct dentry_operations btrfs_dentry_operations = {
+ .d_delete = btrfs_dentry_delete,
+};
struct btrfs_root_item root_item;
struct btrfs_inode_item *inode_item;
struct extent_buffer *leaf;
- struct btrfs_root *new_root = root;
- struct inode *dir;
+ struct btrfs_root *new_root;
+ struct inode *dir = dentry->d_parent->d_inode;
int ret;
int err;
u64 objectid;
u64 index = 0;
unsigned long nr = 1;
- ret = btrfs_check_metadata_free_space(root);
+ /*
+ * 1 - inode item
+ * 2 - refs
+ * 1 - root item
+ * 2 - dir items
+ */
+ ret = btrfs_reserve_metadata_space(root, 6);
if (ret)
- goto fail_commit;
+ return ret;
trans = btrfs_start_transaction(root, 1);
BUG_ON(!trans);
if (ret)
goto fail;
+ key.offset = (u64)-1;
+ new_root = btrfs_read_fs_root_no_name(root->fs_info, &key);
+ BUG_ON(IS_ERR(new_root));
+
+ btrfs_record_root_in_trans(trans, new_root);
+
+ ret = btrfs_create_subvol_root(trans, new_root, new_dirid,
+ BTRFS_I(dir)->block_group);
/*
* insert the directory item
*/
- key.offset = (u64)-1;
- dir = dentry->d_parent->d_inode;
ret = btrfs_set_inode_index(dir, &index);
BUG_ON(ret);
ret = btrfs_update_inode(trans, root, dir);
BUG_ON(ret);
- /* add the backref first */
ret = btrfs_add_root_ref(trans, root->fs_info->tree_root,
- objectid, BTRFS_ROOT_BACKREF_KEY,
- root->root_key.objectid,
+ objectid, root->root_key.objectid,
dir->i_ino, index, name, namelen);
BUG_ON(ret);
- /* now add the forward ref */
- ret = btrfs_add_root_ref(trans, root->fs_info->tree_root,
- root->root_key.objectid, BTRFS_ROOT_REF_KEY,
- objectid,
- dir->i_ino, index, name, namelen);
-
- BUG_ON(ret);
-
- ret = btrfs_commit_transaction(trans, root);
- if (ret)
- goto fail_commit;
-
- new_root = btrfs_read_fs_root_no_name(root->fs_info, &key);
- BUG_ON(!new_root);
-
- trans = btrfs_start_transaction(new_root, 1);
- BUG_ON(!trans);
-
- ret = btrfs_create_subvol_root(trans, new_root, dentry, new_dirid,
- BTRFS_I(dir)->block_group);
- if (ret)
- goto fail;
-
+ d_instantiate(dentry, btrfs_lookup_dentry(dir, dentry));
fail:
nr = trans->blocks_used;
- err = btrfs_commit_transaction(trans, new_root);
+ err = btrfs_commit_transaction(trans, root);
if (err && !ret)
ret = err;
-fail_commit:
+
+ btrfs_unreserve_metadata_space(root, 6);
btrfs_btree_balance_dirty(root, nr);
return ret;
}
if (!root->ref_cows)
return -EINVAL;
- ret = btrfs_check_metadata_free_space(root);
+ /*
+ * 1 - inode item
+ * 2 - refs
+ * 1 - root item
+ * 2 - dir items
+ */
+ ret = btrfs_reserve_metadata_space(root, 6);
if (ret)
goto fail_unlock;
pending_snapshot = kzalloc(sizeof(*pending_snapshot), GFP_NOFS);
if (!pending_snapshot) {
ret = -ENOMEM;
+ btrfs_unreserve_metadata_space(root, 6);
goto fail_unlock;
}
pending_snapshot->name = kmalloc(namelen + 1, GFP_NOFS);
if (!pending_snapshot->name) {
ret = -ENOMEM;
kfree(pending_snapshot);
+ btrfs_unreserve_metadata_space(root, 6);
goto fail_unlock;
}
memcpy(pending_snapshot->name, name, namelen);
* sys_mkdirat and vfs_mkdir, but we only do a single component lookup
* inside this filesystem so it's quite a bit simpler.
*/
-static noinline int btrfs_mksubvol(struct path *parent, char *name,
- int mode, int namelen,
+static noinline int btrfs_mksubvol(struct path *parent,
+ char *name, int namelen,
struct btrfs_root *snap_src)
{
+ struct inode *dir = parent->dentry->d_inode;
struct dentry *dentry;
int error;
- mutex_lock_nested(&parent->dentry->d_inode->i_mutex, I_MUTEX_PARENT);
+ mutex_lock_nested(&dir->i_mutex, I_MUTEX_PARENT);
dentry = lookup_one_len(name, parent->dentry, namelen);
error = PTR_ERR(dentry);
if (dentry->d_inode)
goto out_dput;
- if (!IS_POSIXACL(parent->dentry->d_inode))
- mode &= ~current_umask();
-
error = mnt_want_write(parent->mnt);
if (error)
goto out_dput;
- error = btrfs_may_create(parent->dentry->d_inode, dentry);
+ error = btrfs_may_create(dir, dentry);
if (error)
goto out_drop_write;
- /*
- * Actually perform the low-level subvolume creation after all
- * this VFS fuzz.
- *
- * Eventually we want to pass in an inode under which we create this
- * subvolume, but for now all are under the filesystem root.
- *
- * Also we should pass on the mode eventually to allow creating new
- * subvolume with specific mode bits.
- */
+ down_read(&BTRFS_I(dir)->root->fs_info->subvol_sem);
+
+ if (btrfs_root_refs(&BTRFS_I(dir)->root->root_item) == 0)
+ goto out_up_read;
+
if (snap_src) {
- struct dentry *dir = dentry->d_parent;
- struct dentry *test = dir->d_parent;
- struct btrfs_path *path = btrfs_alloc_path();
- int ret;
- u64 test_oid;
- u64 parent_oid = BTRFS_I(dir->d_inode)->root->root_key.objectid;
-
- test_oid = snap_src->root_key.objectid;
-
- ret = btrfs_find_root_ref(snap_src->fs_info->tree_root,
- path, parent_oid, test_oid);
- if (ret == 0)
- goto create;
- btrfs_release_path(snap_src->fs_info->tree_root, path);
-
- /* we need to make sure we aren't creating a directory loop
- * by taking a snapshot of something that has our current
- * subvol in its directory tree. So, this loops through
- * the dentries and checks the forward refs for each subvolume
- * to see if is references the subvolume where we are
- * placing this new snapshot.
- */
- while (1) {
- if (!test ||
- dir == snap_src->fs_info->sb->s_root ||
- test == snap_src->fs_info->sb->s_root ||
- test->d_inode->i_sb != snap_src->fs_info->sb) {
- break;
- }
- if (S_ISLNK(test->d_inode->i_mode)) {
- printk(KERN_INFO "Btrfs symlink in snapshot "
- "path, failed\n");
- error = -EMLINK;
- btrfs_free_path(path);
- goto out_drop_write;
- }
- test_oid =
- BTRFS_I(test->d_inode)->root->root_key.objectid;
- ret = btrfs_find_root_ref(snap_src->fs_info->tree_root,
- path, test_oid, parent_oid);
- if (ret == 0) {
- printk(KERN_INFO "Btrfs snapshot creation "
- "failed, looping\n");
- error = -EMLINK;
- btrfs_free_path(path);
- goto out_drop_write;
- }
- btrfs_release_path(snap_src->fs_info->tree_root, path);
- test = test->d_parent;
- }
-create:
- btrfs_free_path(path);
- error = create_snapshot(snap_src, dentry, name, namelen);
+ error = create_snapshot(snap_src, dentry,
+ name, namelen);
} else {
- error = create_subvol(BTRFS_I(parent->dentry->d_inode)->root,
- dentry, name, namelen);
+ error = create_subvol(BTRFS_I(dir)->root, dentry,
+ name, namelen);
}
- if (error)
- goto out_drop_write;
-
- fsnotify_mkdir(parent->dentry->d_inode, dentry);
+ if (!error)
+ fsnotify_mkdir(dir, dentry);
+out_up_read:
+ up_read(&BTRFS_I(dir)->root->fs_info->subvol_sem);
out_drop_write:
mnt_drop_write(parent->mnt);
out_dput:
dput(dentry);
out_unlock:
- mutex_unlock(&parent->dentry->d_inode->i_mutex);
+ mutex_unlock(&dir->i_mutex);
return error;
}
-
static int btrfs_defrag_file(struct file *file)
{
struct inode *inode = fdentry(file)->d_inode;
clear_page_dirty_for_io(page);
btrfs_set_extent_delalloc(inode, page_start, page_end);
-
- unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
set_page_dirty(page);
+ unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
unlock_page(page);
page_cache_release(page);
balance_dirty_pages_ratelimited_nr(inode->i_mapping, 1);
return 0;
}
-static int btrfs_ioctl_resize(struct btrfs_root *root, void __user *arg)
+static noinline int btrfs_ioctl_resize(struct btrfs_root *root,
+ void __user *arg)
{
u64 new_size;
u64 old_size;
{
struct btrfs_root *root = BTRFS_I(fdentry(file)->d_inode)->root;
struct btrfs_ioctl_vol_args *vol_args;
- struct btrfs_dir_item *di;
- struct btrfs_path *path;
struct file *src_file;
- u64 root_dirid;
int namelen;
int ret = 0;
goto out;
}
- path = btrfs_alloc_path();
- if (!path) {
- ret = -ENOMEM;
- goto out;
- }
-
- root_dirid = root->fs_info->sb->s_root->d_inode->i_ino,
- di = btrfs_lookup_dir_item(NULL, root->fs_info->tree_root,
- path, root_dirid,
- vol_args->name, namelen, 0);
- btrfs_free_path(path);
-
- if (di && !IS_ERR(di)) {
- ret = -EEXIST;
- goto out;
- }
-
- if (IS_ERR(di)) {
- ret = PTR_ERR(di);
- goto out;
- }
-
if (subvol) {
- ret = btrfs_mksubvol(&file->f_path, vol_args->name,
- file->f_path.dentry->d_inode->i_mode,
- namelen, NULL);
+ ret = btrfs_mksubvol(&file->f_path, vol_args->name, namelen,
+ NULL);
} else {
struct inode *src_inode;
src_file = fget(vol_args->fd);
fput(src_file);
goto out;
}
- ret = btrfs_mksubvol(&file->f_path, vol_args->name,
- file->f_path.dentry->d_inode->i_mode,
- namelen, BTRFS_I(src_inode)->root);
+ ret = btrfs_mksubvol(&file->f_path, vol_args->name, namelen,
+ BTRFS_I(src_inode)->root);
fput(src_file);
}
-
out:
kfree(vol_args);
return ret;
}
+/*
+ * helper to check if the subvolume references other subvolumes
+ */
+static noinline int may_destroy_subvol(struct btrfs_root *root)
+{
+ struct btrfs_path *path;
+ struct btrfs_key key;
+ int ret;
+
+ path = btrfs_alloc_path();
+ if (!path)
+ return -ENOMEM;
+
+ key.objectid = root->root_key.objectid;
+ key.type = BTRFS_ROOT_REF_KEY;
+ key.offset = (u64)-1;
+
+ ret = btrfs_search_slot(NULL, root->fs_info->tree_root,
+ &key, path, 0, 0);
+ if (ret < 0)
+ goto out;
+ BUG_ON(ret == 0);
+
+ ret = 0;
+ if (path->slots[0] > 0) {
+ path->slots[0]--;
+ btrfs_item_key_to_cpu(path->nodes[0], &key, path->slots[0]);
+ if (key.objectid == root->root_key.objectid &&
+ key.type == BTRFS_ROOT_REF_KEY)
+ ret = -ENOTEMPTY;
+ }
+out:
+ btrfs_free_path(path);
+ return ret;
+}
+
+static noinline int btrfs_ioctl_snap_destroy(struct file *file,
+ void __user *arg)
+{
+ struct dentry *parent = fdentry(file);
+ struct dentry *dentry;
+ struct inode *dir = parent->d_inode;
+ struct inode *inode;
+ struct btrfs_root *root = BTRFS_I(dir)->root;
+ struct btrfs_root *dest = NULL;
+ struct btrfs_ioctl_vol_args *vol_args;
+ struct btrfs_trans_handle *trans;
+ int namelen;
+ int ret;
+ int err = 0;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+
+ vol_args = memdup_user(arg, sizeof(*vol_args));
+ if (IS_ERR(vol_args))
+ return PTR_ERR(vol_args);
+
+ vol_args->name[BTRFS_PATH_NAME_MAX] = '\0';
+ namelen = strlen(vol_args->name);
+ if (strchr(vol_args->name, '/') ||
+ strncmp(vol_args->name, "..", namelen) == 0) {
+ err = -EINVAL;
+ goto out;
+ }
+
+ err = mnt_want_write(file->f_path.mnt);
+ if (err)
+ goto out;
+
+ mutex_lock_nested(&dir->i_mutex, I_MUTEX_PARENT);
+ dentry = lookup_one_len(vol_args->name, parent, namelen);
+ if (IS_ERR(dentry)) {
+ err = PTR_ERR(dentry);
+ goto out_unlock_dir;
+ }
+
+ if (!dentry->d_inode) {
+ err = -ENOENT;
+ goto out_dput;
+ }
+
+ inode = dentry->d_inode;
+ if (inode->i_ino != BTRFS_FIRST_FREE_OBJECTID) {
+ err = -EINVAL;
+ goto out_dput;
+ }
+
+ dest = BTRFS_I(inode)->root;
+
+ mutex_lock(&inode->i_mutex);
+ err = d_invalidate(dentry);
+ if (err)
+ goto out_unlock;
+
+ down_write(&root->fs_info->subvol_sem);
+
+ err = may_destroy_subvol(dest);
+ if (err)
+ goto out_up_write;
+
+ trans = btrfs_start_transaction(root, 1);
+ ret = btrfs_unlink_subvol(trans, root, dir,
+ dest->root_key.objectid,
+ dentry->d_name.name,
+ dentry->d_name.len);
+ BUG_ON(ret);
+
+ btrfs_record_root_in_trans(trans, dest);
+
+ memset(&dest->root_item.drop_progress, 0,
+ sizeof(dest->root_item.drop_progress));
+ dest->root_item.drop_level = 0;
+ btrfs_set_root_refs(&dest->root_item, 0);
+
+ ret = btrfs_insert_orphan_item(trans,
+ root->fs_info->tree_root,
+ dest->root_key.objectid);
+ BUG_ON(ret);
+
+ ret = btrfs_commit_transaction(trans, root);
+ BUG_ON(ret);
+ inode->i_flags |= S_DEAD;
+out_up_write:
+ up_write(&root->fs_info->subvol_sem);
+out_unlock:
+ mutex_unlock(&inode->i_mutex);
+ if (!err) {
+ btrfs_invalidate_inodes(dest);
+ d_delete(dentry);
+ }
+out_dput:
+ dput(dentry);
+out_unlock_dir:
+ mutex_unlock(&dir->i_mutex);
+ mnt_drop_write(file->f_path.mnt);
+out:
+ kfree(vol_args);
+ return err;
+}
+
static int btrfs_ioctl_defrag(struct file *file)
{
struct inode *inode = fdentry(file)->d_inode;
return ret;
}
-static long btrfs_ioctl_clone(struct file *file, unsigned long srcfd,
- u64 off, u64 olen, u64 destoff)
+static noinline long btrfs_ioctl_clone(struct file *file, unsigned long srcfd,
+ u64 off, u64 olen, u64 destoff)
{
struct inode *inode = fdentry(file)->d_inode;
struct btrfs_root *root = BTRFS_I(inode)->root;
/* punch hole in destination first */
btrfs_drop_extents(trans, root, inode, off, off + len,
- off + len, 0, &hint_byte);
+ off + len, 0, &hint_byte, 1);
/* clone data */
key.objectid = src->i_ino;
datao += off - key.offset;
datal -= off - key.offset;
}
- if (key.offset + datao + datal + key.offset >
- off + len)
+ if (key.offset + datao + datal > off + len)
datal = off + len - key.offset - datao;
/* disko == 0 means it's a hole */
if (!disko)
struct inode *inode = fdentry(file)->d_inode;
struct btrfs_root *root = BTRFS_I(inode)->root;
struct btrfs_trans_handle *trans;
- int ret = 0;
+ int ret;
+ ret = -EPERM;
if (!capable(CAP_SYS_ADMIN))
- return -EPERM;
+ goto out;
- if (file->private_data) {
- ret = -EINPROGRESS;
+ ret = -EINPROGRESS;
+ if (file->private_data)
goto out;
- }
ret = mnt_want_write(file->f_path.mnt);
if (ret)
root->fs_info->open_ioctl_trans++;
mutex_unlock(&root->fs_info->trans_mutex);
+ ret = -ENOMEM;
trans = btrfs_start_ioctl_transaction(root, 0);
- if (trans)
- file->private_data = trans;
- else
- ret = -ENOMEM;
- /*printk(KERN_INFO "btrfs_ioctl_trans_start on %p\n", file);*/
+ if (!trans)
+ goto out_drop;
+
+ file->private_data = trans;
+ return 0;
+
+out_drop:
+ mutex_lock(&root->fs_info->trans_mutex);
+ root->fs_info->open_ioctl_trans--;
+ mutex_unlock(&root->fs_info->trans_mutex);
+ mnt_drop_write(file->f_path.mnt);
out:
return ret;
}
struct inode *inode = fdentry(file)->d_inode;
struct btrfs_root *root = BTRFS_I(inode)->root;
struct btrfs_trans_handle *trans;
- int ret = 0;
trans = file->private_data;
- if (!trans) {
- ret = -EINVAL;
- goto out;
- }
- btrfs_end_transaction(trans, root);
+ if (!trans)
+ return -EINVAL;
file->private_data = NULL;
+ btrfs_end_transaction(trans, root);
+
mutex_lock(&root->fs_info->trans_mutex);
root->fs_info->open_ioctl_trans--;
mutex_unlock(&root->fs_info->trans_mutex);
mnt_drop_write(file->f_path.mnt);
-
-out:
- return ret;
+ return 0;
}
long btrfs_ioctl(struct file *file, unsigned int
return btrfs_ioctl_snap_create(file, argp, 0);
case BTRFS_IOC_SUBVOL_CREATE:
return btrfs_ioctl_snap_create(file, argp, 1);
+ case BTRFS_IOC_SNAP_DESTROY:
+ return btrfs_ioctl_snap_destroy(file, argp);
case BTRFS_IOC_DEFRAG:
return btrfs_ioctl_defrag(file);
case BTRFS_IOC_RESIZE:
#define BTRFS_IOC_SUBVOL_CREATE _IOW(BTRFS_IOCTL_MAGIC, 14, \
struct btrfs_ioctl_vol_args)
-
+#define BTRFS_IOC_SNAP_DESTROY _IOW(BTRFS_IOCTL_MAGIC, 15, \
+ struct btrfs_ioctl_vol_args)
#endif
*
* len is the length of the extent
*
- * This also sets the EXTENT_ORDERED bit on the range in the inode.
- *
* The tree is given a single reference on the ordered extent that was
* inserted.
*/
entry->start = start;
entry->len = len;
entry->disk_len = disk_len;
+ entry->bytes_left = len;
entry->inode = inode;
if (type != BTRFS_ORDERED_IO_DONE && type != BTRFS_ORDERED_COMPLETE)
set_bit(type, &entry->flags);
&entry->rb_node);
BUG_ON(node);
- set_extent_ordered(&BTRFS_I(inode)->io_tree, file_offset,
- entry_end(entry) - 1, GFP_NOFS);
-
spin_lock(&BTRFS_I(inode)->root->fs_info->ordered_extent_lock);
list_add_tail(&entry->root_extent_list,
&BTRFS_I(inode)->root->fs_info->ordered_extents);
struct btrfs_ordered_inode_tree *tree;
struct rb_node *node;
struct btrfs_ordered_extent *entry;
- struct extent_io_tree *io_tree = &BTRFS_I(inode)->io_tree;
int ret;
tree = &BTRFS_I(inode)->ordered_tree;
mutex_lock(&tree->mutex);
- clear_extent_ordered(io_tree, file_offset, file_offset + io_size - 1,
- GFP_NOFS);
node = tree_search(tree, file_offset);
if (!node) {
ret = 1;
goto out;
}
- ret = test_range_bit(io_tree, entry->file_offset,
- entry->file_offset + entry->len - 1,
- EXTENT_ORDERED, 0);
- if (ret == 0)
+ if (io_size > entry->bytes_left) {
+ printk(KERN_CRIT "bad ordered accounting left %llu size %llu\n",
+ (unsigned long long)entry->bytes_left,
+ (unsigned long long)io_size);
+ }
+ entry->bytes_left -= io_size;
+ if (entry->bytes_left == 0)
ret = test_and_set_bit(BTRFS_ORDERED_IO_DONE, &entry->flags);
+ else
+ ret = 1;
out:
mutex_unlock(&tree->mutex);
return ret == 0;
* start IO on any dirty ones so the wait doesn't stall waiting
* for pdflush to find them
*/
- btrfs_fdatawrite_range(inode->i_mapping, start, end, WB_SYNC_ALL);
+ filemap_fdatawrite_range(inode->i_mapping, start, end);
if (wait) {
wait_event(entry->wait, test_bit(BTRFS_ORDERED_COMPLETE,
&entry->flags));
u64 orig_end;
u64 wait_end;
struct btrfs_ordered_extent *ordered;
+ int found;
if (start + len < start) {
orig_end = INT_LIMIT(loff_t);
/* start IO across the range first to instantiate any delalloc
* extents
*/
- btrfs_fdatawrite_range(inode->i_mapping, start, orig_end, WB_SYNC_ALL);
+ filemap_fdatawrite_range(inode->i_mapping, start, orig_end);
/* The compression code will leave pages locked but return from
* writepage without setting the page writeback. Starting again
* with WB_SYNC_ALL will end up waiting for the IO to actually start.
*/
- btrfs_fdatawrite_range(inode->i_mapping, start, orig_end, WB_SYNC_ALL);
+ filemap_fdatawrite_range(inode->i_mapping, start, orig_end);
- btrfs_wait_on_page_writeback_range(inode->i_mapping,
- start >> PAGE_CACHE_SHIFT,
- orig_end >> PAGE_CACHE_SHIFT);
+ filemap_fdatawait_range(inode->i_mapping, start, orig_end);
end = orig_end;
+ found = 0;
while (1) {
ordered = btrfs_lookup_first_ordered_extent(inode, end);
if (!ordered)
btrfs_put_ordered_extent(ordered);
break;
}
+ found++;
btrfs_start_ordered_extent(inode, ordered, 1);
end = ordered->file_offset;
btrfs_put_ordered_extent(ordered);
break;
end--;
}
- if (test_range_bit(&BTRFS_I(inode)->io_tree, start, orig_end,
- EXTENT_ORDERED | EXTENT_DELALLOC, 0)) {
+ if (found || test_range_bit(&BTRFS_I(inode)->io_tree, start, orig_end,
+ EXTENT_DELALLOC, 0, NULL)) {
schedule_timeout(1);
goto again;
}
*/
if (test_range_bit(io_tree, disk_i_size,
ordered->file_offset + ordered->len - 1,
- EXTENT_DELALLOC, 0)) {
+ EXTENT_DELALLOC, 0, NULL)) {
goto out;
}
/*
*/
if (i_size_test > entry_end(ordered) &&
!test_range_bit(io_tree, entry_end(ordered), i_size_test - 1,
- EXTENT_DELALLOC, 0)) {
+ EXTENT_DELALLOC, 0, NULL)) {
new_i_size = min_t(u64, i_size_test, i_size_read(inode));
}
BTRFS_I(inode)->disk_i_size = new_i_size;
}
-/**
- * taken from mm/filemap.c because it isn't exported
- *
- * __filemap_fdatawrite_range - start writeback on mapping dirty pages in range
- * @mapping: address space structure to write
- * @start: offset in bytes where the range starts
- * @end: offset in bytes where the range ends (inclusive)
- * @sync_mode: enable synchronous operation
- *
- * Start writeback against all of a mapping's dirty pages that lie
- * within the byte offsets <start, end> inclusive.
- *
- * If sync_mode is WB_SYNC_ALL then this is a "data integrity" operation, as
- * opposed to a regular memory cleansing writeback. The difference between
- * these two operations is that if a dirty page/buffer is encountered, it must
- * be waited upon, and not just skipped over.
- */
-int btrfs_fdatawrite_range(struct address_space *mapping, loff_t start,
- loff_t end, int sync_mode)
-{
- struct writeback_control wbc = {
- .sync_mode = sync_mode,
- .nr_to_write = mapping->nrpages * 2,
- .range_start = start,
- .range_end = end,
- };
- return btrfs_writepages(mapping, &wbc);
-}
-
-/**
- * taken from mm/filemap.c because it isn't exported
- *
- * wait_on_page_writeback_range - wait for writeback to complete
- * @mapping: target address_space
- * @start: beginning page index
- * @end: ending page index
- *
- * Wait for writeback to complete against pages indexed by start->end
- * inclusive
- */
-int btrfs_wait_on_page_writeback_range(struct address_space *mapping,
- pgoff_t start, pgoff_t end)
-{
- struct pagevec pvec;
- int nr_pages;
- int ret = 0;
- pgoff_t index;
-
- if (end < start)
- return 0;
-
- pagevec_init(&pvec, 0);
- index = start;
- while ((index <= end) &&
- (nr_pages = pagevec_lookup_tag(&pvec, mapping, &index,
- PAGECACHE_TAG_WRITEBACK,
- min(end - index, (pgoff_t)PAGEVEC_SIZE-1) + 1)) != 0) {
- unsigned i;
-
- for (i = 0; i < nr_pages; i++) {
- struct page *page = pvec.pages[i];
-
- /* until radix tree lookup accepts end_index */
- if (page->index > end)
- continue;
-
- wait_on_page_writeback(page);
- if (PageError(page))
- ret = -EIO;
- }
- pagevec_release(&pvec);
- cond_resched();
- }
-
- /* Check for outstanding write errors */
- if (test_and_clear_bit(AS_ENOSPC, &mapping->flags))
- ret = -ENOSPC;
- if (test_and_clear_bit(AS_EIO, &mapping->flags))
- ret = -EIO;
-
- return ret;
-}
-
/*
* add a given inode to the list of inodes that must be fully on
* disk before a transaction commit finishes.
/* extent length on disk */
u64 disk_len;
+ /* number of bytes that still need writing */
+ u64 bytes_left;
+
/* flags (described above) */
unsigned long flags;
int btrfs_ordered_update_i_size(struct inode *inode,
struct btrfs_ordered_extent *ordered);
int btrfs_find_ordered_sum(struct inode *inode, u64 offset, u64 disk_bytenr, u32 *sum);
-int btrfs_wait_on_page_writeback_range(struct address_space *mapping,
- pgoff_t start, pgoff_t end);
-int btrfs_fdatawrite_range(struct address_space *mapping, loff_t start,
- loff_t end, int sync_mode);
int btrfs_wait_ordered_extents(struct btrfs_root *root, int nocow_only);
int btrfs_run_ordered_operations(struct btrfs_root *root, int wait);
int btrfs_add_ordered_operation(struct btrfs_trans_handle *trans,
btrfs_free_path(path);
return ret;
}
+
+int btrfs_find_orphan_item(struct btrfs_root *root, u64 offset)
+{
+ struct btrfs_path *path;
+ struct btrfs_key key;
+ int ret;
+
+ key.objectid = BTRFS_ORPHAN_OBJECTID;
+ key.type = BTRFS_ORPHAN_ITEM_KEY;
+ key.offset = offset;
+
+ path = btrfs_alloc_path();
+ if (!path)
+ return -ENOMEM;
+
+ ret = btrfs_search_slot(NULL, root, &key, path, 0, 0);
+
+ btrfs_free_path(path);
+ return ret;
+}
int nr;
};
+#define MAX_EXTENTS 128
+
+struct file_extent_cluster {
+ u64 start;
+ u64 end;
+ u64 boundary[MAX_EXTENTS];
+ unsigned int nr;
+};
+
struct reloc_control {
/* block group to relocate */
struct btrfs_block_group_cache *block_group;
struct reloc_control *rc)
{
if (test_range_bit(&rc->processed_blocks, bytenr,
- bytenr + blocksize - 1, EXTENT_DIRTY, 1))
+ bytenr + blocksize - 1, EXTENT_DIRTY, 1, NULL))
return 1;
return 0;
}
}
static noinline_for_stack
-int relocate_inode_pages(struct inode *inode, u64 start, u64 len)
+int setup_extent_mapping(struct inode *inode, u64 start, u64 end,
+ u64 block_start)
+{
+ struct btrfs_root *root = BTRFS_I(inode)->root;
+ struct extent_map_tree *em_tree = &BTRFS_I(inode)->extent_tree;
+ struct extent_map *em;
+ int ret = 0;
+
+ em = alloc_extent_map(GFP_NOFS);
+ if (!em)
+ return -ENOMEM;
+
+ em->start = start;
+ em->len = end + 1 - start;
+ em->block_len = em->len;
+ em->block_start = block_start;
+ em->bdev = root->fs_info->fs_devices->latest_bdev;
+ set_bit(EXTENT_FLAG_PINNED, &em->flags);
+
+ lock_extent(&BTRFS_I(inode)->io_tree, start, end, GFP_NOFS);
+ while (1) {
+ write_lock(&em_tree->lock);
+ ret = add_extent_mapping(em_tree, em);
+ write_unlock(&em_tree->lock);
+ if (ret != -EEXIST) {
+ free_extent_map(em);
+ break;
+ }
+ btrfs_drop_extent_cache(inode, start, end, 0);
+ }
+ unlock_extent(&BTRFS_I(inode)->io_tree, start, end, GFP_NOFS);
+ return ret;
+}
+
+static int relocate_file_extent_cluster(struct inode *inode,
+ struct file_extent_cluster *cluster)
{
u64 page_start;
u64 page_end;
- unsigned long i;
- unsigned long first_index;
+ u64 offset = BTRFS_I(inode)->index_cnt;
+ unsigned long index;
unsigned long last_index;
- unsigned int total_read = 0;
- unsigned int total_dirty = 0;
+ unsigned int dirty_page = 0;
struct page *page;
struct file_ra_state *ra;
- struct btrfs_ordered_extent *ordered;
- struct extent_io_tree *io_tree = &BTRFS_I(inode)->io_tree;
+ int nr = 0;
int ret = 0;
+ if (!cluster->nr)
+ return 0;
+
ra = kzalloc(sizeof(*ra), GFP_NOFS);
if (!ra)
return -ENOMEM;
+ index = (cluster->start - offset) >> PAGE_CACHE_SHIFT;
+ last_index = (cluster->end - offset) >> PAGE_CACHE_SHIFT;
+
mutex_lock(&inode->i_mutex);
- first_index = start >> PAGE_CACHE_SHIFT;
- last_index = (start + len - 1) >> PAGE_CACHE_SHIFT;
- /* make sure the dirty trick played by the caller work */
- while (1) {
- ret = invalidate_inode_pages2_range(inode->i_mapping,
- first_index, last_index);
- if (ret != -EBUSY)
- break;
- schedule_timeout(HZ/10);
- }
+ i_size_write(inode, cluster->end + 1 - offset);
+ ret = setup_extent_mapping(inode, cluster->start - offset,
+ cluster->end - offset, cluster->start);
if (ret)
goto out_unlock;
file_ra_state_init(ra, inode->i_mapping);
- for (i = first_index ; i <= last_index; i++) {
- if (total_read % ra->ra_pages == 0) {
- btrfs_force_ra(inode->i_mapping, ra, NULL, i,
- min(last_index, ra->ra_pages + i - 1));
- }
- total_read++;
-again:
- if (((u64)i << PAGE_CACHE_SHIFT) > i_size_read(inode))
- BUG_ON(1);
- page = grab_cache_page(inode->i_mapping, i);
+ WARN_ON(cluster->start != cluster->boundary[0]);
+ while (index <= last_index) {
+ page = find_lock_page(inode->i_mapping, index);
if (!page) {
- ret = -ENOMEM;
- goto out_unlock;
+ page_cache_sync_readahead(inode->i_mapping,
+ ra, NULL, index,
+ last_index + 1 - index);
+ page = grab_cache_page(inode->i_mapping, index);
+ if (!page) {
+ ret = -ENOMEM;
+ goto out_unlock;
+ }
+ }
+
+ if (PageReadahead(page)) {
+ page_cache_async_readahead(inode->i_mapping,
+ ra, NULL, page, index,
+ last_index + 1 - index);
}
+
if (!PageUptodate(page)) {
btrfs_readpage(NULL, page);
lock_page(page);
goto out_unlock;
}
}
- wait_on_page_writeback(page);
page_start = (u64)page->index << PAGE_CACHE_SHIFT;
page_end = page_start + PAGE_CACHE_SIZE - 1;
- lock_extent(io_tree, page_start, page_end, GFP_NOFS);
-
- ordered = btrfs_lookup_ordered_extent(inode, page_start);
- if (ordered) {
- unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
- unlock_page(page);
- page_cache_release(page);
- btrfs_start_ordered_extent(inode, ordered, 1);
- btrfs_put_ordered_extent(ordered);
- goto again;
- }
+
+ lock_extent(&BTRFS_I(inode)->io_tree,
+ page_start, page_end, GFP_NOFS);
+
set_page_extent_mapped(page);
- if (i == first_index)
- set_extent_bits(io_tree, page_start, page_end,
+ if (nr < cluster->nr &&
+ page_start + offset == cluster->boundary[nr]) {
+ set_extent_bits(&BTRFS_I(inode)->io_tree,
+ page_start, page_end,
EXTENT_BOUNDARY, GFP_NOFS);
+ nr++;
+ }
btrfs_set_extent_delalloc(inode, page_start, page_end);
set_page_dirty(page);
- total_dirty++;
+ dirty_page++;
- unlock_extent(io_tree, page_start, page_end, GFP_NOFS);
+ unlock_extent(&BTRFS_I(inode)->io_tree,
+ page_start, page_end, GFP_NOFS);
unlock_page(page);
page_cache_release(page);
+
+ index++;
+ if (nr < cluster->nr &&
+ page_end + 1 + offset == cluster->boundary[nr]) {
+ balance_dirty_pages_ratelimited_nr(inode->i_mapping,
+ dirty_page);
+ dirty_page = 0;
+ }
+ }
+ if (dirty_page) {
+ balance_dirty_pages_ratelimited_nr(inode->i_mapping,
+ dirty_page);
}
+ WARN_ON(nr != cluster->nr);
out_unlock:
mutex_unlock(&inode->i_mutex);
kfree(ra);
- balance_dirty_pages_ratelimited_nr(inode->i_mapping, total_dirty);
return ret;
}
static noinline_for_stack
-int relocate_data_extent(struct inode *inode, struct btrfs_key *extent_key)
+int relocate_data_extent(struct inode *inode, struct btrfs_key *extent_key,
+ struct file_extent_cluster *cluster)
{
- struct btrfs_root *root = BTRFS_I(inode)->root;
- struct extent_map_tree *em_tree = &BTRFS_I(inode)->extent_tree;
- struct extent_map *em;
- u64 start = extent_key->objectid - BTRFS_I(inode)->index_cnt;
- u64 end = start + extent_key->offset - 1;
-
- em = alloc_extent_map(GFP_NOFS);
- em->start = start;
- em->len = extent_key->offset;
- em->block_len = extent_key->offset;
- em->block_start = extent_key->objectid;
- em->bdev = root->fs_info->fs_devices->latest_bdev;
- set_bit(EXTENT_FLAG_PINNED, &em->flags);
+ int ret;
- /* setup extent map to cheat btrfs_readpage */
- lock_extent(&BTRFS_I(inode)->io_tree, start, end, GFP_NOFS);
- while (1) {
- int ret;
- spin_lock(&em_tree->lock);
- ret = add_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
- if (ret != -EEXIST) {
- free_extent_map(em);
- break;
- }
- btrfs_drop_extent_cache(inode, start, end, 0);
+ if (cluster->nr > 0 && extent_key->objectid != cluster->end + 1) {
+ ret = relocate_file_extent_cluster(inode, cluster);
+ if (ret)
+ return ret;
+ cluster->nr = 0;
}
- unlock_extent(&BTRFS_I(inode)->io_tree, start, end, GFP_NOFS);
- return relocate_inode_pages(inode, start, extent_key->offset);
+ if (!cluster->nr)
+ cluster->start = extent_key->objectid;
+ else
+ BUG_ON(cluster->nr >= MAX_EXTENTS);
+ cluster->end = extent_key->objectid + extent_key->offset - 1;
+ cluster->boundary[cluster->nr] = extent_key->objectid;
+ cluster->nr++;
+
+ if (cluster->nr >= MAX_EXTENTS) {
+ ret = relocate_file_extent_cluster(inode, cluster);
+ if (ret)
+ return ret;
+ cluster->nr = 0;
+ }
+ return 0;
}
#ifdef BTRFS_COMPAT_EXTENT_TREE_V0
return 0;
}
+
static noinline_for_stack int relocate_block_group(struct reloc_control *rc)
{
struct rb_root blocks = RB_ROOT;
struct btrfs_key key;
+ struct file_extent_cluster *cluster;
struct btrfs_trans_handle *trans = NULL;
struct btrfs_path *path;
struct btrfs_extent_item *ei;
int ret;
int err = 0;
+ cluster = kzalloc(sizeof(*cluster), GFP_NOFS);
+ if (!cluster)
+ return -ENOMEM;
+
path = btrfs_alloc_path();
if (!path)
return -ENOMEM;
+ rc->extents_found = 0;
+ rc->extents_skipped = 0;
+
rc->search_start = rc->block_group->key.objectid;
clear_extent_bits(&rc->processed_blocks, 0, (u64)-1, EXTENT_DIRTY,
GFP_NOFS);
}
nr = trans->blocks_used;
- btrfs_end_transaction_throttle(trans, rc->extent_root);
+ btrfs_end_transaction(trans, rc->extent_root);
trans = NULL;
btrfs_btree_balance_dirty(rc->extent_root, nr);
if (rc->stage == MOVE_DATA_EXTENTS &&
(flags & BTRFS_EXTENT_FLAG_DATA)) {
rc->found_file_extent = 1;
- ret = relocate_data_extent(rc->data_inode, &key);
+ ret = relocate_data_extent(rc->data_inode,
+ &key, cluster);
if (ret < 0) {
err = ret;
break;
btrfs_btree_balance_dirty(rc->extent_root, nr);
}
+ if (!err) {
+ ret = relocate_file_extent_cluster(rc->data_inode, cluster);
+ if (ret < 0)
+ err = ret;
+ }
+
+ kfree(cluster);
+
rc->create_reloc_root = 0;
smp_mb();
}
static int __insert_orphan_inode(struct btrfs_trans_handle *trans,
- struct btrfs_root *root,
- u64 objectid, u64 size)
+ struct btrfs_root *root, u64 objectid)
{
struct btrfs_path *path;
struct btrfs_inode_item *item;
item = btrfs_item_ptr(leaf, path->slots[0], struct btrfs_inode_item);
memset_extent_buffer(leaf, 0, (unsigned long)item, sizeof(*item));
btrfs_set_inode_generation(leaf, item, 1);
- btrfs_set_inode_size(leaf, item, size);
+ btrfs_set_inode_size(leaf, item, 0);
btrfs_set_inode_mode(leaf, item, S_IFREG | 0600);
btrfs_set_inode_flags(leaf, item, BTRFS_INODE_NOCOMPRESS);
btrfs_mark_buffer_dirty(leaf);
if (err)
goto out;
- err = __insert_orphan_inode(trans, root, objectid, group->key.offset);
- BUG_ON(err);
-
- err = btrfs_insert_file_extent(trans, root, objectid, 0, 0, 0,
- group->key.offset, 0, group->key.offset,
- 0, 0, 0);
+ err = __insert_orphan_inode(trans, root, objectid);
BUG_ON(err);
key.objectid = objectid;
btrfs_wait_ordered_extents(fs_info->tree_root, 0);
while (1) {
- mutex_lock(&fs_info->cleaner_mutex);
- btrfs_clean_old_snapshots(fs_info->tree_root);
- mutex_unlock(&fs_info->cleaner_mutex);
-
rc->extents_found = 0;
rc->extents_skipped = 0;
+ mutex_lock(&fs_info->cleaner_mutex);
+
+ btrfs_clean_old_snapshots(fs_info->tree_root);
ret = relocate_block_group(rc);
+
+ mutex_unlock(&fs_info->cleaner_mutex);
if (ret < 0) {
err = ret;
break;
}
}
- filemap_fdatawrite_range(fs_info->btree_inode->i_mapping,
- rc->block_group->key.objectid,
- rc->block_group->key.objectid +
- rc->block_group->key.offset - 1);
+ filemap_write_and_wait_range(fs_info->btree_inode->i_mapping,
+ rc->block_group->key.objectid,
+ rc->block_group->key.objectid +
+ rc->block_group->key.offset - 1);
WARN_ON(rc->block_group->pinned > 0);
WARN_ON(rc->block_group->reserved > 0);
return err;
}
+static noinline_for_stack int mark_garbage_root(struct btrfs_root *root)
+{
+ struct btrfs_trans_handle *trans;
+ int ret;
+
+ trans = btrfs_start_transaction(root->fs_info->tree_root, 1);
+
+ memset(&root->root_item.drop_progress, 0,
+ sizeof(root->root_item.drop_progress));
+ root->root_item.drop_level = 0;
+ btrfs_set_root_refs(&root->root_item, 0);
+ ret = btrfs_update_root(trans, root->fs_info->tree_root,
+ &root->root_key, &root->root_item);
+ BUG_ON(ret);
+
+ ret = btrfs_end_transaction(trans, root->fs_info->tree_root);
+ BUG_ON(ret);
+ return 0;
+}
+
/*
* recover relocation interrupted by system crash.
*
fs_root = read_fs_root(root->fs_info,
reloc_root->root_key.offset);
if (IS_ERR(fs_root)) {
- err = PTR_ERR(fs_root);
- goto out;
+ ret = PTR_ERR(fs_root);
+ if (ret != -ENOENT) {
+ err = ret;
+ goto out;
+ }
+ mark_garbage_root(reloc_root);
}
}
goto out;
BUG_ON(ret == 0);
+ if (path->slots[0] == 0) {
+ ret = 1;
+ goto out;
+ }
l = path->nodes[0];
- BUG_ON(path->slots[0] == 0);
slot = path->slots[0] - 1;
btrfs_item_key_to_cpu(l, &found_key, slot);
- if (found_key.objectid != objectid) {
+ if (found_key.objectid != objectid ||
+ found_key.type != BTRFS_ROOT_ITEM_KEY) {
ret = 1;
goto out;
}
- read_extent_buffer(l, item, btrfs_item_ptr_offset(l, slot),
- sizeof(*item));
- memcpy(key, &found_key, sizeof(found_key));
+ if (item)
+ read_extent_buffer(l, item, btrfs_item_ptr_offset(l, slot),
+ sizeof(*item));
+ if (key)
+ memcpy(key, &found_key, sizeof(found_key));
ret = 0;
out:
btrfs_free_path(path);
return ret;
}
+int btrfs_find_orphan_roots(struct btrfs_root *tree_root)
+{
+ struct extent_buffer *leaf;
+ struct btrfs_path *path;
+ struct btrfs_key key;
+ int err = 0;
+ int ret;
+
+ path = btrfs_alloc_path();
+ if (!path)
+ return -ENOMEM;
+
+ key.objectid = BTRFS_ORPHAN_OBJECTID;
+ key.type = BTRFS_ORPHAN_ITEM_KEY;
+ key.offset = 0;
+
+ while (1) {
+ ret = btrfs_search_slot(NULL, tree_root, &key, path, 0, 0);
+ if (ret < 0) {
+ err = ret;
+ break;
+ }
+
+ leaf = path->nodes[0];
+ if (path->slots[0] >= btrfs_header_nritems(leaf)) {
+ ret = btrfs_next_leaf(tree_root, path);
+ if (ret < 0)
+ err = ret;
+ if (ret != 0)
+ break;
+ leaf = path->nodes[0];
+ }
+
+ btrfs_item_key_to_cpu(leaf, &key, path->slots[0]);
+ btrfs_release_path(tree_root, path);
+
+ if (key.objectid != BTRFS_ORPHAN_OBJECTID ||
+ key.type != BTRFS_ORPHAN_ITEM_KEY)
+ break;
+
+ ret = btrfs_find_dead_roots(tree_root, key.offset);
+ if (ret) {
+ err = ret;
+ break;
+ }
+
+ key.offset++;
+ }
+
+ btrfs_free_path(path);
+ return err;
+}
+
/* drop the root item for 'key' from 'root' */
int btrfs_del_root(struct btrfs_trans_handle *trans, struct btrfs_root *root,
struct btrfs_key *key)
return ret;
}
-#if 0 /* this will get used when snapshot deletion is implemented */
int btrfs_del_root_ref(struct btrfs_trans_handle *trans,
struct btrfs_root *tree_root,
- u64 root_id, u8 type, u64 ref_id)
+ u64 root_id, u64 ref_id, u64 dirid, u64 *sequence,
+ const char *name, int name_len)
+
{
+ struct btrfs_path *path;
+ struct btrfs_root_ref *ref;
+ struct extent_buffer *leaf;
struct btrfs_key key;
+ unsigned long ptr;
+ int err = 0;
int ret;
- struct btrfs_path *path;
path = btrfs_alloc_path();
+ if (!path)
+ return -ENOMEM;
key.objectid = root_id;
- key.type = type;
+ key.type = BTRFS_ROOT_BACKREF_KEY;
key.offset = ref_id;
-
+again:
ret = btrfs_search_slot(trans, tree_root, &key, path, -1, 1);
- BUG_ON(ret);
-
- ret = btrfs_del_item(trans, tree_root, path);
- BUG_ON(ret);
+ BUG_ON(ret < 0);
+ if (ret == 0) {
+ leaf = path->nodes[0];
+ ref = btrfs_item_ptr(leaf, path->slots[0],
+ struct btrfs_root_ref);
+
+ WARN_ON(btrfs_root_ref_dirid(leaf, ref) != dirid);
+ WARN_ON(btrfs_root_ref_name_len(leaf, ref) != name_len);
+ ptr = (unsigned long)(ref + 1);
+ WARN_ON(memcmp_extent_buffer(leaf, name, ptr, name_len));
+ *sequence = btrfs_root_ref_sequence(leaf, ref);
+
+ ret = btrfs_del_item(trans, tree_root, path);
+ BUG_ON(ret);
+ } else
+ err = -ENOENT;
+
+ if (key.type == BTRFS_ROOT_BACKREF_KEY) {
+ btrfs_release_path(tree_root, path);
+ key.objectid = ref_id;
+ key.type = BTRFS_ROOT_REF_KEY;
+ key.offset = root_id;
+ goto again;
+ }
btrfs_free_path(path);
- return ret;
+ return err;
}
-#endif
int btrfs_find_root_ref(struct btrfs_root *tree_root,
struct btrfs_path *path,
return ret;
}
-
/*
* add a btrfs_root_ref item. type is either BTRFS_ROOT_REF_KEY
* or BTRFS_ROOT_BACKREF_KEY.
*/
int btrfs_add_root_ref(struct btrfs_trans_handle *trans,
struct btrfs_root *tree_root,
- u64 root_id, u8 type, u64 ref_id,
- u64 dirid, u64 sequence,
+ u64 root_id, u64 ref_id, u64 dirid, u64 sequence,
const char *name, int name_len)
{
struct btrfs_key key;
struct extent_buffer *leaf;
unsigned long ptr;
-
path = btrfs_alloc_path();
+ if (!path)
+ return -ENOMEM;
key.objectid = root_id;
- key.type = type;
+ key.type = BTRFS_ROOT_BACKREF_KEY;
key.offset = ref_id;
-
+again:
ret = btrfs_insert_empty_item(trans, tree_root, path, &key,
sizeof(*ref) + name_len);
BUG_ON(ret);
write_extent_buffer(leaf, name, ptr, name_len);
btrfs_mark_buffer_dirty(leaf);
+ if (key.type == BTRFS_ROOT_BACKREF_KEY) {
+ btrfs_release_path(tree_root, path);
+ key.objectid = ref_id;
+ key.type = BTRFS_ROOT_REF_KEY;
+ key.offset = root_id;
+ goto again;
+ }
+
btrfs_free_path(path);
- return ret;
+ return 0;
}
sb->s_export_op = &btrfs_export_ops;
sb->s_xattr = btrfs_xattr_handlers;
sb->s_time_gran = 1;
+#ifdef CONFIG_BTRFS_POSIX_ACL
sb->s_flags |= MS_POSIXACL;
+#endif
tree_root = open_ctree(sb, fs_devices, (char *)data);
}
static const struct super_operations btrfs_super_ops = {
+ .drop_inode = btrfs_drop_inode,
.delete_inode = btrfs_delete_inode,
.put_super = btrfs_put_super,
.sync_fs = btrfs_sync_fs,
{
if (root->ref_cows && root->last_trans < trans->transid) {
WARN_ON(root == root->fs_info->extent_root);
- WARN_ON(root->root_item.refs == 0);
WARN_ON(root->commit_root != root->node);
radix_tree_tag_set(&root->fs_info->fs_roots_radix,
h->alloc_exclude_start = 0;
h->delayed_ref_updates = 0;
+ if (!current->journal_info)
+ current->journal_info = h;
+
root->fs_info->running_transaction->use_count++;
record_root_in_trans(h, root);
mutex_unlock(&root->fs_info->trans_mutex);
wake_up(&cur_trans->writer_wait);
put_transaction(cur_trans);
mutex_unlock(&info->trans_mutex);
+
+ if (current->journal_info == trans)
+ current->journal_info = NULL;
memset(trans, 0, sizeof(*trans));
kmem_cache_free(btrfs_trans_handle_cachep, trans);
memcpy(new_root_item, &root->root_item, sizeof(*new_root_item));
key.objectid = objectid;
- key.offset = 0;
+ /* record when the snapshot was created in key.offset */
+ key.offset = trans->transid;
btrfs_set_key_type(&key, BTRFS_ROOT_ITEM_KEY);
old = btrfs_lock_root_node(root);
memcpy(&pending->root_key, &key, sizeof(key));
fail:
kfree(new_root_item);
+ btrfs_unreserve_metadata_space(root, 6);
return ret;
}
ret = btrfs_update_inode(trans, parent_root, parent_inode);
BUG_ON(ret);
- /* add the backref first */
ret = btrfs_add_root_ref(trans, parent_root->fs_info->tree_root,
pending->root_key.objectid,
- BTRFS_ROOT_BACKREF_KEY,
parent_root->root_key.objectid,
parent_inode->i_ino, index, pending->name,
namelen);
BUG_ON(ret);
- /* now add the forward ref */
- ret = btrfs_add_root_ref(trans, parent_root->fs_info->tree_root,
- parent_root->root_key.objectid,
- BTRFS_ROOT_REF_KEY,
- pending->root_key.objectid,
- parent_inode->i_ino, index, pending->name,
- namelen);
-
inode = btrfs_lookup_dentry(parent_inode, pending->dentry);
d_instantiate(pending->dentry, inode);
fail:
unsigned long timeout = 1;
struct btrfs_transaction *cur_trans;
struct btrfs_transaction *prev_trans = NULL;
- struct extent_io_tree *pinned_copy;
DEFINE_WAIT(wait);
int ret;
int should_grow = 0;
return 0;
}
- pinned_copy = kmalloc(sizeof(*pinned_copy), GFP_NOFS);
- if (!pinned_copy)
- return -ENOMEM;
-
- extent_io_tree_init(pinned_copy,
- root->fs_info->btree_inode->i_mapping, GFP_NOFS);
-
trans->transaction->in_commit = 1;
trans->transaction->blocked = 1;
if (cur_trans->list.prev != &root->fs_info->trans_list) {
ret = commit_cowonly_roots(trans, root);
BUG_ON(ret);
+ btrfs_prepare_extent_commit(trans, root);
+
cur_trans = root->fs_info->running_transaction;
spin_lock(&root->fs_info->new_trans_lock);
root->fs_info->running_transaction = NULL;
memcpy(&root->fs_info->super_for_commit, &root->fs_info->super_copy,
sizeof(root->fs_info->super_copy));
- btrfs_copy_pinned(root, pinned_copy);
-
trans->transaction->blocked = 0;
wake_up(&root->fs_info->transaction_wait);
*/
mutex_unlock(&root->fs_info->tree_log_mutex);
- btrfs_finish_extent_commit(trans, root, pinned_copy);
- kfree(pinned_copy);
+ btrfs_finish_extent_commit(trans, root);
/* do the directory inserts of any pending snapshot creations */
finish_pending_snapshots(trans, root->fs_info);
mutex_unlock(&root->fs_info->trans_mutex);
+ if (current->journal_info == trans)
+ current->journal_info = NULL;
+
kmem_cache_free(btrfs_trans_handle_cachep, trans);
return ret;
}
while (!list_empty(&list)) {
root = list_entry(list.next, struct btrfs_root, root_list);
- list_del_init(&root->root_list);
- btrfs_drop_snapshot(root, 0);
+ list_del(&root->root_list);
+
+ if (btrfs_header_backref_rev(root->node) <
+ BTRFS_MIXED_BACKREF_REV)
+ btrfs_drop_snapshot(root, 0);
+ else
+ btrfs_drop_snapshot(root, 1);
}
return 0;
}
struct walk_control *wc, u64 gen)
{
if (wc->pin)
- btrfs_update_pinned_extents(log->fs_info->extent_root,
- eb->start, eb->len, 1);
+ btrfs_pin_extent(log->fs_info->extent_root,
+ eb->start, eb->len, 0);
if (btrfs_buffer_uptodate(eb, gen)) {
if (wc->write)
saved_nbytes = inode_get_bytes(inode);
/* drop any overlapping extents */
ret = btrfs_drop_extents(trans, root, inode,
- start, extent_end, extent_end, start, &alloc_hint);
+ start, extent_end, extent_end, start, &alloc_hint, 1);
BUG_ON(ret);
if (found_type == BTRFS_FILE_EXTENT_REG ||
if (!parent || !parent->d_inode || sb != parent->d_inode->i_sb)
break;
- if (parent == sb->s_root)
+ if (IS_ROOT(parent))
break;
parent = parent->d_parent;
goto end_no_trans;
}
+ if (root != BTRFS_I(inode)->root ||
+ btrfs_root_refs(&root->root_item) == 0) {
+ ret = 1;
+ goto end_no_trans;
+ }
+
ret = check_parent_dirs_for_sync(trans, inode, parent,
sb, last_committed);
if (ret)
break;
inode = parent->d_inode;
+ if (root != BTRFS_I(inode)->root)
+ break;
+
if (BTRFS_I(inode)->generation >
root->fs_info->last_trans_committed) {
ret = btrfs_log_inode(trans, root, inode, inode_only);
BUG_ON(ret);
}
- if (parent == sb->s_root)
+ if (IS_ROOT(parent))
break;
parent = parent->d_parent;
struct btrfs_key tmp_key;
struct btrfs_root *log;
struct btrfs_fs_info *fs_info = log_root_tree->fs_info;
- u64 highest_inode;
struct walk_control wc = {
.process_func = process_one_buffer,
.stage = 0,
path);
BUG_ON(ret);
}
- ret = btrfs_find_highest_inode(wc.replay_dest, &highest_inode);
- if (ret == 0) {
- wc.replay_dest->highest_inode = highest_inode;
- wc.replay_dest->last_inode_alloc = highest_inode;
- }
key.offset = found_key.offset - 1;
wc.replay_dest->log_root = NULL;
* is now congested. Back off and let other work structs
* run instead
*/
- if (pending && bdi_write_congested(bdi) && batch_run > 32 &&
+ if (pending && bdi_write_congested(bdi) && batch_run > 8 &&
fs_info->fs_devices->open_devices > 1) {
struct io_context *ioc;
goto error;
device->name = kstrdup(orig_dev->name, GFP_NOFS);
- if (!device->name)
+ if (!device->name) {
+ kfree(device);
goto error;
+ }
device->devid = orig_dev->devid;
device->work.func = pending_bios_fn;
* called very infrequently and that a given device has a small number
* of extents
*/
-static noinline int find_free_dev_extent(struct btrfs_trans_handle *trans,
- struct btrfs_device *device,
- u64 num_bytes, u64 *start,
- u64 *max_avail)
+int find_free_dev_extent(struct btrfs_trans_handle *trans,
+ struct btrfs_device *device, u64 num_bytes,
+ u64 *start, u64 *max_avail)
{
struct btrfs_key key;
struct btrfs_root *root = device->dev_root;
extent_root = root->fs_info->extent_root;
em_tree = &root->fs_info->mapping_tree.map_tree;
+ ret = btrfs_can_relocate(extent_root, chunk_offset);
+ if (ret)
+ return -ENOSPC;
+
/* step one, relocate all the extents inside this chunk */
ret = btrfs_relocate_block_group(extent_root, chunk_offset);
BUG_ON(ret);
* step two, delete the device extents and the
* chunk tree entries
*/
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, chunk_offset, 1);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
BUG_ON(em->start > chunk_offset ||
em->start + em->len < chunk_offset);
ret = btrfs_remove_block_group(trans, extent_root, chunk_offset);
BUG_ON(ret);
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
remove_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
kfree(map);
em->bdev = NULL;
struct btrfs_key found_key;
u64 chunk_tree = chunk_root->root_key.objectid;
u64 chunk_type;
+ bool retried = false;
+ int failed = 0;
int ret;
path = btrfs_alloc_path();
if (!path)
return -ENOMEM;
+again:
key.objectid = BTRFS_FIRST_CHUNK_TREE_OBJECTID;
key.offset = (u64)-1;
key.type = BTRFS_CHUNK_ITEM_KEY;
ret = btrfs_relocate_chunk(chunk_root, chunk_tree,
found_key.objectid,
found_key.offset);
- BUG_ON(ret);
+ if (ret == -ENOSPC)
+ failed++;
+ else if (ret)
+ BUG();
}
if (found_key.offset == 0)
key.offset = found_key.offset - 1;
}
ret = 0;
+ if (failed && !retried) {
+ failed = 0;
+ retried = true;
+ goto again;
+ } else if (failed && retried) {
+ WARN_ON(1);
+ ret = -ENOSPC;
+ }
error:
btrfs_free_path(path);
return ret;
continue;
ret = btrfs_shrink_device(device, old_size - size_to_free);
+ if (ret == -ENOSPC)
+ break;
BUG_ON(ret);
trans = btrfs_start_transaction(dev_root, 1);
chunk = btrfs_item_ptr(path->nodes[0],
path->slots[0],
struct btrfs_chunk);
- key.offset = found_key.offset;
/* chunk zero is special */
- if (key.offset == 0)
+ if (found_key.offset == 0)
break;
btrfs_release_path(chunk_root, path);
chunk_root->root_key.objectid,
found_key.objectid,
found_key.offset);
- BUG_ON(ret);
+ BUG_ON(ret && ret != -ENOSPC);
+ key.offset = found_key.offset - 1;
}
ret = 0;
error:
u64 chunk_offset;
int ret;
int slot;
+ int failed = 0;
+ bool retried = false;
struct extent_buffer *l;
struct btrfs_key key;
struct btrfs_super_block *super_copy = &root->fs_info->super_copy;
u64 old_total = btrfs_super_total_bytes(super_copy);
+ u64 old_size = device->total_bytes;
u64 diff = device->total_bytes - new_size;
if (new_size >= device->total_bytes)
if (!path)
return -ENOMEM;
- trans = btrfs_start_transaction(root, 1);
- if (!trans) {
- ret = -ENOMEM;
- goto done;
- }
-
path->reada = 2;
lock_chunks(root);
if (device->writeable)
device->fs_devices->total_rw_bytes -= diff;
unlock_chunks(root);
- btrfs_end_transaction(trans, root);
+again:
key.objectid = device->devid;
key.offset = (u64)-1;
key.type = BTRFS_DEV_EXTENT_KEY;
goto done;
if (ret) {
ret = 0;
+ btrfs_release_path(root, path);
break;
}
slot = path->slots[0];
btrfs_item_key_to_cpu(l, &key, path->slots[0]);
- if (key.objectid != device->devid)
+ if (key.objectid != device->devid) {
+ btrfs_release_path(root, path);
break;
+ }
dev_extent = btrfs_item_ptr(l, slot, struct btrfs_dev_extent);
length = btrfs_dev_extent_length(l, dev_extent);
- if (key.offset + length <= new_size)
+ if (key.offset + length <= new_size) {
+ btrfs_release_path(root, path);
break;
+ }
chunk_tree = btrfs_dev_extent_chunk_tree(l, dev_extent);
chunk_objectid = btrfs_dev_extent_chunk_objectid(l, dev_extent);
ret = btrfs_relocate_chunk(root, chunk_tree, chunk_objectid,
chunk_offset);
- if (ret)
+ if (ret && ret != -ENOSPC)
goto done;
+ if (ret == -ENOSPC)
+ failed++;
+ key.offset -= 1;
+ }
+
+ if (failed && !retried) {
+ failed = 0;
+ retried = true;
+ goto again;
+ } else if (failed && retried) {
+ ret = -ENOSPC;
+ lock_chunks(root);
+
+ device->total_bytes = old_size;
+ if (device->writeable)
+ device->fs_devices->total_rw_bytes += diff;
+ unlock_chunks(root);
+ goto done;
}
/* Shrinking succeeded, else we would be at "done". */
em->block_len = em->len;
em_tree = &extent_root->fs_info->mapping_tree.map_tree;
- spin_lock(&em_tree->lock);
+ write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em);
- spin_unlock(&em_tree->lock);
+ write_unlock(&em_tree->lock);
BUG_ON(ret);
free_extent_map(em);
int readonly = 0;
int i;
- spin_lock(&map_tree->map_tree.lock);
+ read_lock(&map_tree->map_tree.lock);
em = lookup_extent_mapping(&map_tree->map_tree, chunk_offset, 1);
- spin_unlock(&map_tree->map_tree.lock);
+ read_unlock(&map_tree->map_tree.lock);
if (!em)
return 1;
struct extent_map *em;
while (1) {
- spin_lock(&tree->map_tree.lock);
+ write_lock(&tree->map_tree.lock);
em = lookup_extent_mapping(&tree->map_tree, 0, (u64)-1);
if (em)
remove_extent_mapping(&tree->map_tree, em);
- spin_unlock(&tree->map_tree.lock);
+ write_unlock(&tree->map_tree.lock);
if (!em)
break;
kfree(em->bdev);
struct extent_map_tree *em_tree = &map_tree->map_tree;
int ret;
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, logical, len);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
BUG_ON(!em);
BUG_ON(em->start > logical || em->start + em->len < logical);
atomic_set(&multi->error, 0);
}
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, logical, *length);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
if (!em && unplug_page)
return 0;
u64 stripe_nr;
int i, j, nr = 0;
- spin_lock(&em_tree->lock);
+ read_lock(&em_tree->lock);
em = lookup_extent_mapping(em_tree, chunk_start, 1);
- spin_unlock(&em_tree->lock);
+ read_unlock(&em_tree->lock);
BUG_ON(!em || em->start != chunk_start);
map = (struct map_lookup *)em->bdev;
logical = key->offset;
length = btrfs_chunk_length(leaf, chunk);
- spin_lock(&map_tree->map_tree.lock);
+ read_lock(&map_tree->map_tree.lock);
em = lookup_extent_mapping(&map_tree->map_tree, logical, 1);
- spin_unlock(&map_tree->map_tree.lock);
+ read_unlock(&map_tree->map_tree.lock);
/* already mapped? */
if (em && em->start <= logical && em->start + em->len > logical) {
map->stripes[i].dev->in_fs_metadata = 1;
}
- spin_lock(&map_tree->map_tree.lock);
+ write_lock(&map_tree->map_tree.lock);
ret = add_extent_mapping(&map_tree->map_tree, em);
- spin_unlock(&map_tree->map_tree.lock);
+ write_unlock(&map_tree->map_tree.lock);
BUG_ON(ret);
free_extent_map(em);
void btrfs_unlock_volumes(void);
void btrfs_lock_volumes(void);
int btrfs_chunk_readonly(struct btrfs_root *root, u64 chunk_offset);
+int find_free_dev_extent(struct btrfs_trans_handle *trans,
+ struct btrfs_device *device, u64 num_bytes,
+ u64 *start, u64 *max_avail);
#endif
* attributes are handled directly.
*/
struct xattr_handler *btrfs_xattr_handlers[] = {
-#ifdef CONFIG_FS_POSIX_ACL
+#ifdef CONFIG_BTRFS_POSIX_ACL
&btrfs_xattr_acl_access_handler,
&btrfs_xattr_acl_default_handler,
#endif
EXPORT_SYMBOL(invalidate_bdev);
/*
- * Kick pdflush then try to free up some ZONE_NORMAL memory.
+ * Kick the writeback threads then try to free up some ZONE_NORMAL memory.
*/
static void free_more_memory(void)
{
/*
* If it's a fully non-blocking write attempt and we cannot
* lock the buffer then redirty the page. Note that this can
- * potentially cause a busy-wait loop from pdflush and kswapd
- * activity, but those code paths have their own higher-level
- * throttling.
+ * potentially cause a busy-wait loop from writeback threads
+ * and kswapd activity, but those code paths have their own
+ * higher-level throttling.
*/
if (wbc->sync_mode != WB_SYNC_NONE || !wbc->nonblocking) {
lock_buffer(bh);
struct address_space *mapping = inode->i_mapping;
struct page *page;
void *fsdata;
- unsigned long limit;
int err;
- err = -EFBIG;
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && size > (loff_t)limit) {
- send_sig(SIGXFSZ, current, 0);
- goto out;
- }
- if (size > inode->i_sb->s_maxbytes)
+ err = inode_newsize_ok(inode, size);
+ if (err)
goto out;
err = pagecache_write_begin(NULL, mapping, size, 0,
* still running obsolete flush daemons, so we terminate them here.
*
* Use of bdflush() is deprecated and will be removed in a future kernel.
- * The `pdflush' kernel threads fully replace bdflush daemons and this call.
+ * The `flush-X' kernel threads fully replace bdflush daemons and this call.
*/
SYSCALL_DEFINE2(bdflush, int, func, long, data)
{
{
struct char_device_struct *cd;
struct cdev *cdev;
- char *s;
int err = -ENOMEM;
cd = __register_chrdev_region(major, baseminor, count, name);
cdev->owner = fops->owner;
cdev->ops = fops;
kobject_set_name(&cdev->kobj, "%s", name);
- for (s = strchr(kobject_name(&cdev->kobj),'/'); s; s = strchr(s, '/'))
- *s = '!';
err = cdev_add(cdev, MKDEV(cd->major, baseminor), count);
if (err)
tristate "CIFS support (advanced network filesystem, SMBFS successor)"
depends on INET
select NLS
+ select SLOW_WORK
help
This is the client VFS module for the Common Internet File System
(CIFS) protocol which is the successor to the Server Message Block
unsigned int extended_security = CIFSSEC_DEF;
/* unsigned int ntlmv2_support = 0; */
unsigned int sign_CIFS_PDUs = 1;
-extern struct task_struct *oplockThread; /* remove sparse warning */
-struct task_struct *oplockThread = NULL;
-/* extern struct task_struct * dnotifyThread; remove sparse warning */
static const struct super_operations cifs_super_ops;
unsigned int CIFSMaxBufSize = CIFS_MAX_MSGSIZE;
module_param(CIFSMaxBufSize, int, 0);
cifs_sb->mountdata = NULL;
}
#endif
- if (cifs_sb->local_nls)
- unload_nls(cifs_sb->local_nls);
+ unload_nls(cifs_sb->local_nls);
kfree(cifs_sb);
}
return rc;
kmem_cache_destroy(cifs_oplock_cachep);
}
-static int cifs_oplock_thread(void *dummyarg)
-{
- struct oplock_q_entry *oplock_item;
- struct cifsTconInfo *pTcon;
- struct inode *inode;
- __u16 netfid;
- int rc, waitrc = 0;
-
- set_freezable();
- do {
- if (try_to_freeze())
- continue;
-
- spin_lock(&cifs_oplock_lock);
- if (list_empty(&cifs_oplock_list)) {
- spin_unlock(&cifs_oplock_lock);
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(39*HZ);
- } else {
- oplock_item = list_entry(cifs_oplock_list.next,
- struct oplock_q_entry, qhead);
- cFYI(1, ("found oplock item to write out"));
- pTcon = oplock_item->tcon;
- inode = oplock_item->pinode;
- netfid = oplock_item->netfid;
- spin_unlock(&cifs_oplock_lock);
- DeleteOplockQEntry(oplock_item);
- /* can not grab inode sem here since it would
- deadlock when oplock received on delete
- since vfs_unlink holds the i_mutex across
- the call */
- /* mutex_lock(&inode->i_mutex);*/
- if (S_ISREG(inode->i_mode)) {
-#ifdef CONFIG_CIFS_EXPERIMENTAL
- if (CIFS_I(inode)->clientCanCacheAll == 0)
- break_lease(inode, FMODE_READ);
- else if (CIFS_I(inode)->clientCanCacheRead == 0)
- break_lease(inode, FMODE_WRITE);
-#endif
- rc = filemap_fdatawrite(inode->i_mapping);
- if (CIFS_I(inode)->clientCanCacheRead == 0) {
- waitrc = filemap_fdatawait(
- inode->i_mapping);
- invalidate_remote_inode(inode);
- }
- if (rc == 0)
- rc = waitrc;
- } else
- rc = 0;
- /* mutex_unlock(&inode->i_mutex);*/
- if (rc)
- CIFS_I(inode)->write_behind_rc = rc;
- cFYI(1, ("Oplock flush inode %p rc %d",
- inode, rc));
-
- /* releasing stale oplock after recent reconnect
- of smb session using a now incorrect file
- handle is not a data integrity issue but do
- not bother sending an oplock release if session
- to server still is disconnected since oplock
- already released by the server in that case */
- if (!pTcon->need_reconnect) {
- rc = CIFSSMBLock(0, pTcon, netfid,
- 0 /* len */ , 0 /* offset */, 0,
- 0, LOCKING_ANDX_OPLOCK_RELEASE,
- false /* wait flag */);
- cFYI(1, ("Oplock release rc = %d", rc));
- }
- set_current_state(TASK_INTERRUPTIBLE);
- schedule_timeout(1); /* yield in case q were corrupt */
- }
- } while (!kthread_should_stop());
-
- return 0;
-}
-
static int __init
init_cifs(void)
{
int rc = 0;
cifs_proc_init();
INIT_LIST_HEAD(&cifs_tcp_ses_list);
- INIT_LIST_HEAD(&cifs_oplock_list);
#ifdef CONFIG_CIFS_EXPERIMENTAL
INIT_LIST_HEAD(&GlobalDnotifyReqList);
INIT_LIST_HEAD(&GlobalDnotifyRsp_Q);
rwlock_init(&GlobalSMBSeslock);
rwlock_init(&cifs_tcp_ses_lock);
spin_lock_init(&GlobalMid_Lock);
- spin_lock_init(&cifs_oplock_lock);
if (cifs_max_pending < 2) {
cifs_max_pending = 2;
if (rc)
goto out_unregister_key_type;
#endif
- oplockThread = kthread_run(cifs_oplock_thread, NULL, "cifsoplockd");
- if (IS_ERR(oplockThread)) {
- rc = PTR_ERR(oplockThread);
- cERROR(1, ("error %d create oplock thread", rc));
- goto out_unregister_dfs_key_type;
- }
+ rc = slow_work_register_user();
+ if (rc)
+ goto out_unregister_resolver_key;
return 0;
- out_unregister_dfs_key_type:
+ out_unregister_resolver_key:
#ifdef CONFIG_CIFS_DFS_UPCALL
unregister_key_type(&key_type_dns_resolver);
out_unregister_key_type:
cifs_destroy_inodecache();
cifs_destroy_mids();
cifs_destroy_request_bufs();
- kthread_stop(oplockThread);
}
MODULE_AUTHOR("Steve French <sfrench@us.ibm.com>");
*/
#include <linux/in.h>
#include <linux/in6.h>
+#include <linux/slow-work.h>
#include "cifs_fs_sb.h"
#include "cifsacl.h"
/*
/* lock scope id (0 if none) */
struct file *pfile; /* needed for writepage */
struct inode *pInode; /* needed for oplock break */
+ struct vfsmount *mnt;
struct mutex lock_mutex;
struct list_head llist; /* list of byte range locks we have. */
bool closePend:1; /* file is marked to close */
bool invalidHandle:1; /* file closed via session abend */
- bool messageMode:1; /* for pipes: message vs byte mode */
+ bool oplock_break_cancelled:1;
atomic_t count; /* reference count */
struct mutex fh_mutex; /* prevents reopen race after dead ses*/
struct cifs_search_info srch_inf;
+ struct slow_work oplock_break; /* slow_work job for oplock breaks */
};
/* Take a reference on the file private data */
/* Release a reference on the file private data */
static inline void cifsFileInfo_put(struct cifsFileInfo *cifs_file)
{
- if (atomic_dec_and_test(&cifs_file->count))
+ if (atomic_dec_and_test(&cifs_file->count)) {
+ iput(cifs_file->pInode);
kfree(cifs_file);
+ }
}
/*
unsigned long time; /* jiffies of last update/check of inode */
bool clientCanCacheRead:1; /* read oplock */
bool clientCanCacheAll:1; /* read and writebehind oplock */
- bool oplockPending:1;
bool delete_pending:1; /* DELETE_ON_CLOSE is set */
u64 server_eof; /* current file size on server */
u64 uniqueid; /* server inode number */
#define CIFSSEC_MUST_LANMAN 0x10010
#define CIFSSEC_MUST_PLNTXT 0x20020
#ifdef CONFIG_CIFS_UPCALL
-#define CIFSSEC_MASK 0xAF0AF /* allows weak security but also krb5 */
+#define CIFSSEC_MASK 0xBF0BF /* allows weak security but also krb5 */
#else
-#define CIFSSEC_MASK 0xA70A7 /* current flags supported if weak */
+#define CIFSSEC_MASK 0xB70B7 /* current flags supported if weak */
#endif /* UPCALL */
#else /* do not allow weak pw hash */
#ifdef CONFIG_CIFS_UPCALL
*/
GLOBAL_EXTERN rwlock_t GlobalSMBSeslock;
-/* Global list of oplocks */
-GLOBAL_EXTERN struct list_head cifs_oplock_list;
-
-/* Protects the cifs_oplock_list */
-GLOBAL_EXTERN spinlock_t cifs_oplock_lock;
-
/* Outstanding dir notify requests */
GLOBAL_EXTERN struct list_head GlobalDnotifyReqList;
/* DirNotify response queue */
GLOBAL_EXTERN unsigned int cifs_min_small; /* min size of small buf pool */
GLOBAL_EXTERN unsigned int cifs_max_pending; /* MAX requests at once to server*/
+extern const struct slow_work_ops cifs_oplock_break_ops;
const int stage,
const struct nls_table *nls_cp);
extern __u16 GetNextMid(struct TCP_Server_Info *server);
-extern struct oplock_q_entry *AllocOplockQEntry(struct inode *, u16,
- struct cifsTconInfo *);
-extern void DeleteOplockQEntry(struct oplock_q_entry *);
-extern void DeleteTconOplockQEntries(struct cifsTconInfo *);
extern struct timespec cifs_NTtimeToUnix(__le64 utc_nanoseconds_since_1601);
extern u64 cifs_UnixTimeToNT(struct timespec);
extern struct timespec cnvrtDosUnixTm(__le16 le_date, __le16 le_time,
int offset);
+extern struct cifsFileInfo *cifs_new_fileinfo(struct inode *newinode,
+ __u16 fileHandle, struct file *file,
+ struct vfsmount *mnt, unsigned int oflags);
extern int cifs_posix_open(char *full_path, struct inode **pinode,
- struct super_block *sb, int mode, int oflags,
- int *poplock, __u16 *pnetfid, int xid);
+ struct vfsmount *mnt, int mode, int oflags,
+ __u32 *poplock, __u16 *pnetfid, int xid);
extern void cifs_unix_basic_to_fattr(struct cifs_fattr *fattr,
FILE_UNIX_BASIC_INFO *info,
struct cifs_sb_info *cifs_sb);
list_for_each_safe(tmp, tmp1, &pTcon->openFileList) {
open_file = list_entry(tmp, struct cifsFileInfo, tlist);
open_file->invalidHandle = true;
+ open_file->oplock_break_cancelled = true;
}
write_unlock(&GlobalSMBSeslock);
/* BB Add call to invalidate_inodes(sb) for all superblocks mounted
CIFSSMBTDis(xid, tcon);
_FreeXid(xid);
- DeleteTconOplockQEntries(tcon);
tconInfoFree(tcon);
cifs_put_smb_ses(ses);
}
#include <linux/stat.h>
#include <linux/slab.h>
#include <linux/namei.h>
+#include <linux/mount.h>
#include "cifsfs.h"
#include "cifspdu.h"
#include "cifsglob.h"
return full_path;
}
-static void
-cifs_fill_fileinfo(struct inode *newinode, __u16 fileHandle,
- struct cifsTconInfo *tcon, bool write_only)
+struct cifsFileInfo *
+cifs_new_fileinfo(struct inode *newinode, __u16 fileHandle,
+ struct file *file, struct vfsmount *mnt, unsigned int oflags)
{
int oplock = 0;
struct cifsFileInfo *pCifsFile;
struct cifsInodeInfo *pCifsInode;
+ struct cifs_sb_info *cifs_sb = CIFS_SB(mnt->mnt_sb);
pCifsFile = kzalloc(sizeof(struct cifsFileInfo), GFP_KERNEL);
-
if (pCifsFile == NULL)
- return;
+ return pCifsFile;
if (oplockEnabled)
oplock = REQ_OPLOCK;
pCifsFile->netfid = fileHandle;
pCifsFile->pid = current->tgid;
- pCifsFile->pInode = newinode;
+ pCifsFile->pInode = igrab(newinode);
+ pCifsFile->mnt = mnt;
+ pCifsFile->pfile = file;
pCifsFile->invalidHandle = false;
pCifsFile->closePend = false;
mutex_init(&pCifsFile->fh_mutex);
mutex_init(&pCifsFile->lock_mutex);
INIT_LIST_HEAD(&pCifsFile->llist);
atomic_set(&pCifsFile->count, 1);
+ slow_work_init(&pCifsFile->oplock_break, &cifs_oplock_break_ops);
- /* set the following in open now
- pCifsFile->pfile = file; */
write_lock(&GlobalSMBSeslock);
- list_add(&pCifsFile->tlist, &tcon->openFileList);
+ list_add(&pCifsFile->tlist, &cifs_sb->tcon->openFileList);
pCifsInode = CIFS_I(newinode);
if (pCifsInode) {
/* if readable file instance put first in list*/
- if (write_only)
+ if (oflags & FMODE_READ)
+ list_add(&pCifsFile->flist, &pCifsInode->openFileList);
+ else
list_add_tail(&pCifsFile->flist,
&pCifsInode->openFileList);
- else
- list_add(&pCifsFile->flist, &pCifsInode->openFileList);
if ((oplock & 0xF) == OPLOCK_EXCLUSIVE) {
pCifsInode->clientCanCacheAll = true;
pCifsInode->clientCanCacheRead = true;
}
write_unlock(&GlobalSMBSeslock);
+
+ return pCifsFile;
}
int cifs_posix_open(char *full_path, struct inode **pinode,
- struct super_block *sb, int mode, int oflags,
- int *poplock, __u16 *pnetfid, int xid)
+ struct vfsmount *mnt, int mode, int oflags,
+ __u32 *poplock, __u16 *pnetfid, int xid)
{
int rc;
- __u32 oplock;
- bool write_only = false;
FILE_UNIX_BASIC_INFO *presp_data;
__u32 posix_flags = 0;
- struct cifs_sb_info *cifs_sb = CIFS_SB(sb);
+ struct cifs_sb_info *cifs_sb = CIFS_SB(mnt->mnt_sb);
struct cifs_fattr fattr;
cFYI(1, ("posix open %s", full_path));
if (oflags & O_DIRECT)
posix_flags |= SMB_O_DIRECT;
- if (!(oflags & FMODE_READ))
- write_only = true;
-
mode &= ~current_umask();
rc = CIFSPOSIXCreate(xid, cifs_sb->tcon, posix_flags, mode,
- pnetfid, presp_data, &oplock, full_path,
+ pnetfid, presp_data, poplock, full_path,
cifs_sb->local_nls, cifs_sb->mnt_cifs_flags &
CIFS_MOUNT_MAP_SPECIAL_CHR);
if (rc)
/* get new inode and set it up */
if (*pinode == NULL) {
- *pinode = cifs_iget(sb, &fattr);
+ *pinode = cifs_iget(mnt->mnt_sb, &fattr);
if (!*pinode) {
rc = -ENOMEM;
goto posix_open_ret;
cifs_fattr_to_inode(*pinode, &fattr);
}
- cifs_fill_fileinfo(*pinode, *pnetfid, cifs_sb->tcon, write_only);
+ cifs_new_fileinfo(*pinode, *pnetfid, NULL, mnt, oflags);
posix_open_ret:
kfree(presp_data);
int rc = -ENOENT;
int xid;
int create_options = CREATE_NOT_DIR;
- int oplock = 0;
+ __u32 oplock = 0;
int oflags;
bool posix_create = false;
/*
FILE_ALL_INFO *buf = NULL;
struct inode *newinode = NULL;
int disposition = FILE_OVERWRITE_IF;
- bool write_only = false;
xid = GetXid();
if (tcon->unix_ext && (tcon->ses->capabilities & CAP_UNIX) &&
(CIFS_UNIX_POSIX_PATH_OPS_CAP &
le64_to_cpu(tcon->fsUnixInfo.Capability))) {
- rc = cifs_posix_open(full_path, &newinode, inode->i_sb,
+ rc = cifs_posix_open(full_path, &newinode, nd->path.mnt,
mode, oflags, &oplock, &fileHandle, xid);
/* EIO could indicate that (posix open) operation is not
supported, despite what server claimed in capability
desiredAccess = 0;
if (oflags & FMODE_READ)
desiredAccess |= GENERIC_READ; /* is this too little? */
- if (oflags & FMODE_WRITE) {
+ if (oflags & FMODE_WRITE)
desiredAccess |= GENERIC_WRITE;
- if (!(oflags & FMODE_READ))
- write_only = true;
- }
if ((oflags & (O_CREAT | O_EXCL)) == (O_CREAT | O_EXCL))
disposition = FILE_CREATE;
/* mknod case - do not leave file open */
CIFSSMBClose(xid, tcon, fileHandle);
} else if (!(posix_create) && (newinode)) {
- cifs_fill_fileinfo(newinode, fileHandle,
- cifs_sb->tcon, write_only);
+ cifs_new_fileinfo(newinode, fileHandle, NULL,
+ nd->path.mnt, oflags);
}
cifs_create_out:
kfree(buf);
{
int xid;
int rc = 0; /* to get around spurious gcc warning, set to zero here */
- int oplock = 0;
+ __u32 oplock = 0;
__u16 fileHandle = 0;
bool posix_open = false;
struct cifs_sb_info *cifs_sb;
if (!(nd->flags & (LOOKUP_PARENT | LOOKUP_DIRECTORY)) &&
(nd->flags & LOOKUP_OPEN) && !pTcon->broken_posix_open &&
(nd->intent.open.flags & O_CREAT)) {
- rc = cifs_posix_open(full_path, &newInode,
- parent_dir_inode->i_sb,
+ rc = cifs_posix_open(full_path, &newInode, nd->path.mnt,
nd->intent.open.create_mode,
nd->intent.open.flags, &oplock,
&fileHandle, xid);
#include <linux/writeback.h>
#include <linux/task_io_accounting_ops.h>
#include <linux/delay.h>
+#include <linux/mount.h>
#include <asm/div64.h>
#include "cifsfs.h"
#include "cifspdu.h"
#include "cifs_debug.h"
#include "cifs_fs_sb.h"
-static inline struct cifsFileInfo *cifs_init_private(
- struct cifsFileInfo *private_data, struct inode *inode,
- struct file *file, __u16 netfid)
-{
- memset(private_data, 0, sizeof(struct cifsFileInfo));
- private_data->netfid = netfid;
- private_data->pid = current->tgid;
- mutex_init(&private_data->fh_mutex);
- mutex_init(&private_data->lock_mutex);
- INIT_LIST_HEAD(&private_data->llist);
- private_data->pfile = file; /* needed for writepage */
- private_data->pInode = inode;
- private_data->invalidHandle = false;
- private_data->closePend = false;
- /* Initialize reference count to one. The private data is
- freed on the release of the last reference */
- atomic_set(&private_data->count, 1);
-
- return private_data;
-}
-
static inline int cifs_convert_flags(unsigned int flags)
{
if ((flags & O_ACCMODE) == O_RDONLY)
}
/* all arguments to this function must be checked for validity in caller */
-static inline int cifs_posix_open_inode_helper(struct inode *inode,
- struct file *file, struct cifsInodeInfo *pCifsInode,
- struct cifsFileInfo *pCifsFile, int oplock, u16 netfid)
+static inline int
+cifs_posix_open_inode_helper(struct inode *inode, struct file *file,
+ struct cifsInodeInfo *pCifsInode,
+ struct cifsFileInfo *pCifsFile, __u32 oplock,
+ u16 netfid)
{
write_lock(&GlobalSMBSeslock);
struct timespec temp;
int rc;
- /* want handles we can use to read with first
- in the list so we do not have to walk the
- list to search for one in write_begin */
- if ((file->f_flags & O_ACCMODE) == O_WRONLY) {
- list_add_tail(&pCifsFile->flist,
- &pCifsInode->openFileList);
- } else {
- list_add(&pCifsFile->flist,
- &pCifsInode->openFileList);
- }
- write_unlock(&GlobalSMBSeslock);
if (pCifsInode->clientCanCacheRead) {
/* we have the inode open somewhere else
no need to discard cache data */
int cifs_open(struct inode *inode, struct file *file)
{
int rc = -EACCES;
- int xid, oplock;
+ int xid;
+ __u32 oplock;
struct cifs_sb_info *cifs_sb;
struct cifsTconInfo *tcon;
struct cifsFileInfo *pCifsFile;
le64_to_cpu(tcon->fsUnixInfo.Capability))) {
int oflags = (int) cifs_posix_convert_flags(file->f_flags);
/* can not refresh inode info since size could be stale */
- rc = cifs_posix_open(full_path, &inode, inode->i_sb,
+ rc = cifs_posix_open(full_path, &inode, file->f_path.mnt,
cifs_sb->mnt_file_mode /* ignored */,
oflags, &oplock, &netfid, xid);
if (rc == 0) {
cFYI(1, ("cifs_open returned 0x%x", rc));
goto out;
}
- file->private_data =
- kmalloc(sizeof(struct cifsFileInfo), GFP_KERNEL);
+
+ pCifsFile = cifs_new_fileinfo(inode, netfid, file, file->f_path.mnt,
+ file->f_flags);
+ file->private_data = pCifsFile;
if (file->private_data == NULL) {
rc = -ENOMEM;
goto out;
}
- pCifsFile = cifs_init_private(file->private_data, inode, file, netfid);
- write_lock(&GlobalSMBSeslock);
- list_add(&pCifsFile->tlist, &tcon->openFileList);
- pCifsInode = CIFS_I(file->f_path.dentry->d_inode);
- if (pCifsInode) {
- rc = cifs_open_inode_helper(inode, file, pCifsInode,
- pCifsFile, tcon,
- &oplock, buf, full_path, xid);
- } else {
- write_unlock(&GlobalSMBSeslock);
- }
+ rc = cifs_open_inode_helper(inode, file, pCifsInode, pCifsFile, tcon,
+ &oplock, buf, full_path, xid);
if (oplock & CIFS_CREATE_ACTION) {
/* time to set mode which we can not set earlier due to
static int cifs_reopen_file(struct file *file, bool can_flush)
{
int rc = -EACCES;
- int xid, oplock;
+ int xid;
+ __u32 oplock;
struct cifs_sb_info *cifs_sb;
struct cifsTconInfo *tcon;
struct cifsFileInfo *pCifsFile;
le64_to_cpu(tcon->fsUnixInfo.Capability))) {
int oflags = (int) cifs_posix_convert_flags(file->f_flags);
/* can not refresh inode info since size could be stale */
- rc = cifs_posix_open(full_path, NULL, inode->i_sb,
+ rc = cifs_posix_open(full_path, NULL, file->f_path.mnt,
cifs_sb->mnt_file_mode /* ignored */,
oflags, &oplock, &netfid, xid);
if (rc == 0) {
return rc;
}
+static void
+cifs_oplock_break(struct slow_work *work)
+{
+ struct cifsFileInfo *cfile = container_of(work, struct cifsFileInfo,
+ oplock_break);
+ struct inode *inode = cfile->pInode;
+ struct cifsInodeInfo *cinode = CIFS_I(inode);
+ struct cifs_sb_info *cifs_sb = CIFS_SB(cfile->mnt->mnt_sb);
+ int rc, waitrc = 0;
+
+ if (inode && S_ISREG(inode->i_mode)) {
+#ifdef CONFIG_CIFS_EXPERIMENTAL
+ if (cinode->clientCanCacheAll == 0)
+ break_lease(inode, FMODE_READ);
+ else if (cinode->clientCanCacheRead == 0)
+ break_lease(inode, FMODE_WRITE);
+#endif
+ rc = filemap_fdatawrite(inode->i_mapping);
+ if (cinode->clientCanCacheRead == 0) {
+ waitrc = filemap_fdatawait(inode->i_mapping);
+ invalidate_remote_inode(inode);
+ }
+ if (!rc)
+ rc = waitrc;
+ if (rc)
+ cinode->write_behind_rc = rc;
+ cFYI(1, ("Oplock flush inode %p rc %d", inode, rc));
+ }
+
+ /*
+ * releasing stale oplock after recent reconnect of smb session using
+ * a now incorrect file handle is not a data integrity issue but do
+ * not bother sending an oplock release if session to server still is
+ * disconnected since oplock already released by the server
+ */
+ if (!cfile->closePend && !cfile->oplock_break_cancelled) {
+ rc = CIFSSMBLock(0, cifs_sb->tcon, cfile->netfid, 0, 0, 0, 0,
+ LOCKING_ANDX_OPLOCK_RELEASE, false);
+ cFYI(1, ("Oplock release rc = %d", rc));
+ }
+}
+
+static int
+cifs_oplock_break_get(struct slow_work *work)
+{
+ struct cifsFileInfo *cfile = container_of(work, struct cifsFileInfo,
+ oplock_break);
+ mntget(cfile->mnt);
+ cifsFileInfo_get(cfile);
+ return 0;
+}
+
+static void
+cifs_oplock_break_put(struct slow_work *work)
+{
+ struct cifsFileInfo *cfile = container_of(work, struct cifsFileInfo,
+ oplock_break);
+ mntput(cfile->mnt);
+ cifsFileInfo_put(cfile);
+}
+
+const struct slow_work_ops cifs_oplock_break_ops = {
+ .get_ref = cifs_oplock_break_get,
+ .put_ref = cifs_oplock_break_put,
+ .execute = cifs_oplock_break,
+};
+
const struct address_space_operations cifs_addr_ops = {
.readpage = cifs_readpage,
.readpages = cifs_readpages,
static int cifs_vmtruncate(struct inode *inode, loff_t offset)
{
- struct address_space *mapping = inode->i_mapping;
- unsigned long limit;
+ loff_t oldsize;
+ int err;
spin_lock(&inode->i_lock);
- if (inode->i_size < offset)
- goto do_expand;
- /*
- * truncation of in-use swapfiles is disallowed - it would cause
- * subsequent swapout to scribble on the now-freed blocks.
- */
- if (IS_SWAPFILE(inode)) {
- spin_unlock(&inode->i_lock);
- goto out_busy;
- }
- i_size_write(inode, offset);
- spin_unlock(&inode->i_lock);
- /*
- * unmap_mapping_range is called twice, first simply for efficiency
- * so that truncate_inode_pages does fewer single-page unmaps. However
- * after this first call, and before truncate_inode_pages finishes,
- * it is possible for private pages to be COWed, which remain after
- * truncate_inode_pages finishes, hence the second unmap_mapping_range
- * call must be made for correctness.
- */
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- truncate_inode_pages(mapping, offset);
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- goto out_truncate;
-
-do_expand:
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && offset > limit) {
+ err = inode_newsize_ok(inode, offset);
+ if (err) {
spin_unlock(&inode->i_lock);
- goto out_sig;
- }
- if (offset > inode->i_sb->s_maxbytes) {
- spin_unlock(&inode->i_lock);
- goto out_big;
+ goto out;
}
+
+ oldsize = inode->i_size;
i_size_write(inode, offset);
spin_unlock(&inode->i_lock);
-out_truncate:
+ truncate_pagecache(inode, oldsize, offset);
if (inode->i_op->truncate)
inode->i_op->truncate(inode);
- return 0;
-out_sig:
- send_sig(SIGXFSZ, current, 0);
-out_big:
- return -EFBIG;
-out_busy:
- return -ETXTBSY;
+out:
+ return err;
}
static int
extern mempool_t *cifs_sm_req_poolp;
extern mempool_t *cifs_req_poolp;
-extern struct task_struct *oplockThread;
/* The xid serves as a useful identifier for each incoming vfs request,
in a similar way to the mid which is useful to track each sent smb,
struct cifsTconInfo *tcon;
struct cifsInodeInfo *pCifsInode;
struct cifsFileInfo *netfile;
+ int rc;
cFYI(1, ("Checking for oplock break or dnotify response"));
if ((pSMB->hdr.Command == SMB_COM_NT_TRANSACT) &&
continue;
cifs_stats_inc(&tcon->num_oplock_brks);
- write_lock(&GlobalSMBSeslock);
+ read_lock(&GlobalSMBSeslock);
list_for_each(tmp2, &tcon->openFileList) {
netfile = list_entry(tmp2, struct cifsFileInfo,
tlist);
if (pSMB->Fid != netfile->netfid)
continue;
- write_unlock(&GlobalSMBSeslock);
- read_unlock(&cifs_tcp_ses_lock);
+ /*
+ * don't do anything if file is about to be
+ * closed anyway.
+ */
+ if (netfile->closePend) {
+ read_unlock(&GlobalSMBSeslock);
+ read_unlock(&cifs_tcp_ses_lock);
+ return true;
+ }
+
cFYI(1, ("file id match, oplock break"));
pCifsInode = CIFS_I(netfile->pInode);
pCifsInode->clientCanCacheAll = false;
if (pSMB->OplockLevel == 0)
pCifsInode->clientCanCacheRead = false;
- pCifsInode->oplockPending = true;
- AllocOplockQEntry(netfile->pInode,
- netfile->netfid, tcon);
- cFYI(1, ("about to wake up oplock thread"));
- if (oplockThread)
- wake_up_process(oplockThread);
-
+ rc = slow_work_enqueue(&netfile->oplock_break);
+ if (rc) {
+ cERROR(1, ("failed to enqueue oplock "
+ "break: %d\n", rc));
+ } else {
+ netfile->oplock_break_cancelled = false;
+ }
+ read_unlock(&GlobalSMBSeslock);
+ read_unlock(&cifs_tcp_ses_lock);
return true;
}
- write_unlock(&GlobalSMBSeslock);
+ read_unlock(&GlobalSMBSeslock);
read_unlock(&cifs_tcp_ses_lock);
cFYI(1, ("No matching file for oplock break"));
return true;
}
}
-void
+static void
cifs_dir_info_to_fattr(struct cifs_fattr *fattr, FILE_DIRECTORY_INFO *info,
struct cifs_sb_info *cifs_sb)
{
cifs_fill_common_info(fattr, cifs_sb);
}
-void
+static void
cifs_std_info_to_fattr(struct cifs_fattr *fattr, FIND_FILE_STANDARD_INFO *info,
struct cifs_sb_info *cifs_sb)
{
mempool_free(midEntry, cifs_mid_poolp);
}
-struct oplock_q_entry *
-AllocOplockQEntry(struct inode *pinode, __u16 fid, struct cifsTconInfo *tcon)
-{
- struct oplock_q_entry *temp;
- if ((pinode == NULL) || (tcon == NULL)) {
- cERROR(1, ("Null parms passed to AllocOplockQEntry"));
- return NULL;
- }
- temp = (struct oplock_q_entry *) kmem_cache_alloc(cifs_oplock_cachep,
- GFP_KERNEL);
- if (temp == NULL)
- return temp;
- else {
- temp->pinode = pinode;
- temp->tcon = tcon;
- temp->netfid = fid;
- spin_lock(&cifs_oplock_lock);
- list_add_tail(&temp->qhead, &cifs_oplock_list);
- spin_unlock(&cifs_oplock_lock);
- }
- return temp;
-}
-
-void DeleteOplockQEntry(struct oplock_q_entry *oplockEntry)
-{
- spin_lock(&cifs_oplock_lock);
- /* should we check if list empty first? */
- list_del(&oplockEntry->qhead);
- spin_unlock(&cifs_oplock_lock);
- kmem_cache_free(cifs_oplock_cachep, oplockEntry);
-}
-
-
-void DeleteTconOplockQEntries(struct cifsTconInfo *tcon)
-{
- struct oplock_q_entry *temp;
-
- if (tcon == NULL)
- return;
-
- spin_lock(&cifs_oplock_lock);
- list_for_each_entry(temp, &cifs_oplock_list, qhead) {
- if ((temp->tcon) && (temp->tcon == tcon)) {
- list_del(&temp->qhead);
- kmem_cache_free(cifs_oplock_cachep, temp);
- }
- }
- spin_unlock(&cifs_oplock_lock);
-}
-
static int
smb_sendv(struct TCP_Server_Info *server, struct kvec *iov, int n_vec)
{
#define _CODA_INT_
struct dentry;
+struct file;
extern struct file_system_type coda_fs_type;
extern unsigned long coda_timeout;
#include <linux/kernel.h>
#include <linux/major.h>
#include <linux/time.h>
+#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/ioport.h>
#include <linux/fcntl.h>
char __user * type, unsigned long flags,
void __user * data)
{
- unsigned long type_page;
+ char *kernel_type;
unsigned long data_page;
- unsigned long dev_page;
+ char *kernel_dev;
char *dir_page;
int retval;
- retval = copy_mount_options (type, &type_page);
+ retval = copy_mount_string(type, &kernel_type);
if (retval < 0)
goto out;
if (IS_ERR(dir_page))
goto out1;
- retval = copy_mount_options (dev_name, &dev_page);
+ retval = copy_mount_string(dev_name, &kernel_dev);
if (retval < 0)
goto out2;
- retval = copy_mount_options (data, &data_page);
+ retval = copy_mount_options(data, &data_page);
if (retval < 0)
goto out3;
retval = -EINVAL;
- if (type_page && data_page) {
- if (!strcmp((char *)type_page, SMBFS_NAME)) {
+ if (kernel_type && data_page) {
+ if (!strcmp(kernel_type, SMBFS_NAME)) {
do_smb_super_data_conv((void *)data_page);
- } else if (!strcmp((char *)type_page, NCPFS_NAME)) {
+ } else if (!strcmp(kernel_type, NCPFS_NAME)) {
do_ncp_super_data_conv((void *)data_page);
- } else if (!strcmp((char *)type_page, NFS4_NAME)) {
+ } else if (!strcmp(kernel_type, NFS4_NAME)) {
if (do_nfs4_super_data_conv((void *) data_page))
goto out4;
}
}
- retval = do_mount((char*)dev_page, dir_page, (char*)type_page,
+ retval = do_mount(kernel_dev, dir_page, kernel_type,
flags, (void*)data_page);
out4:
free_page(data_page);
out3:
- free_page(dev_page);
+ kfree(kernel_dev);
out2:
putname(dir_page);
out1:
- free_page(type_page);
+ kfree(kernel_type);
out:
return retval;
}
}
int drop_caches_sysctl_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
- proc_dointvec_minmax(table, write, file, buffer, length, ppos);
+ proc_dointvec_minmax(table, write, buffer, length, ppos);
if (write) {
if (sysctl_drop_caches & 1)
drop_pagecache();
config ECRYPT_FS
tristate "eCrypt filesystem layer support (EXPERIMENTAL)"
- depends on EXPERIMENTAL && KEYS && CRYPTO && NET
+ depends on EXPERIMENTAL && KEYS && NET
+ select CRYPTO_ECB
+ select CRYPTO_CBC
help
Encrypted filesystem that operates on the VFS layer. See
<file:Documentation/filesystems/ecryptfs.txt> to learn more about
crypto_free_blkcipher(crypt_stat->tfm);
if (crypt_stat->hash_tfm)
crypto_free_hash(crypt_stat->hash_tfm);
- mutex_lock(&crypt_stat->keysig_list_mutex);
list_for_each_entry_safe(key_sig, key_sig_tmp,
&crypt_stat->keysig_list, crypt_stat_list) {
list_del(&key_sig->crypt_stat_list);
kmem_cache_free(ecryptfs_key_sig_cache, key_sig);
}
- mutex_unlock(&crypt_stat->keysig_list_mutex);
memset(crypt_stat, 0, sizeof(struct ecryptfs_crypt_stat));
}
+ extent_offset), crypt_stat);
rc = ecryptfs_write_lower(ecryptfs_inode, enc_extent_virt,
offset, crypt_stat->extent_size);
- if (rc) {
+ if (rc < 0) {
ecryptfs_printk(KERN_ERR, "Error attempting "
"to write lower page; rc = [%d]"
"\n", rc);
goto out;
}
}
+ rc = 0;
out:
if (enc_extent_page) {
kunmap(enc_extent_page);
rc = ecryptfs_read_lower(enc_extent_virt, offset,
crypt_stat->extent_size,
ecryptfs_inode);
- if (rc) {
+ if (rc < 0) {
ecryptfs_printk(KERN_ERR, "Error attempting "
"to read lower page; rc = [%d]"
"\n", rc);
kfree(full_alg_name);
if (IS_ERR(crypt_stat->tfm)) {
rc = PTR_ERR(crypt_stat->tfm);
+ crypt_stat->tfm = NULL;
ecryptfs_printk(KERN_ERR, "cryptfs: init_crypt_ctx(): "
"Error initializing cipher [%s]\n",
crypt_stat->cipher);
struct ecryptfs_global_auth_tok *global_auth_tok;
int rc = 0;
+ mutex_lock(&crypt_stat->keysig_list_mutex);
mutex_lock(&mount_crypt_stat->global_auth_tok_list_mutex);
+
list_for_each_entry(global_auth_tok,
&mount_crypt_stat->global_auth_tok_list,
mount_crypt_stat_list) {
rc = ecryptfs_add_keysig(crypt_stat, global_auth_tok->sig);
if (rc) {
printk(KERN_ERR "Error adding keysig; rc = [%d]\n", rc);
- mutex_unlock(
- &mount_crypt_stat->global_auth_tok_list_mutex);
goto out;
}
}
- mutex_unlock(&mount_crypt_stat->global_auth_tok_list_mutex);
+
out:
+ mutex_unlock(&mount_crypt_stat->global_auth_tok_list_mutex);
+ mutex_unlock(&crypt_stat->keysig_list_mutex);
return rc;
}
crypt_stat->extent_size = ECRYPTFS_DEFAULT_EXTENT_SIZE;
rc = ecryptfs_read_lower(data, 0, crypt_stat->extent_size,
ecryptfs_inode);
- if (rc) {
+ if (rc < 0) {
printk(KERN_ERR "%s: Error reading header region; rc = [%d]\n",
__func__, rc);
goto out;
}
if (!contains_ecryptfs_marker(data + ECRYPTFS_FILE_SIZE_BYTES)) {
rc = -EINVAL;
- }
+ } else
+ rc = 0;
out:
return rc;
}
rc = ecryptfs_write_lower(ecryptfs_dentry->d_inode, virt,
0, virt_len);
- if (rc)
+ if (rc < 0)
printk(KERN_ERR "%s: Error attempting to write header "
- "information to lower file; rc = [%d]\n", __func__,
- rc);
+ "information to lower file; rc = [%d]\n", __func__, rc);
+ else
+ rc = 0;
return rc;
}
}
rc = ecryptfs_read_lower(page_virt, 0, crypt_stat->extent_size,
ecryptfs_inode);
- if (!rc)
+ if (rc >= 0)
rc = ecryptfs_read_headers_virt(page_virt, crypt_stat,
ecryptfs_dentry,
ECRYPTFS_VALIDATE_HEADER_SIZE);
} else {
printk(KERN_ERR "%s: No support for requested filename "
"encryption method in this release\n", __func__);
- rc = -ENOTSUPP;
+ rc = -EOPNOTSUPP;
goto out;
}
out:
if (IS_ERR(*key_tfm)) {
rc = PTR_ERR(*key_tfm);
printk(KERN_ERR "Unable to allocate crypto cipher with name "
- "[%s]; rc = [%d]\n", cipher_name, rc);
+ "[%s]; rc = [%d]\n", full_alg_name, rc);
goto out;
}
crypto_blkcipher_set_flags(*key_tfm, CRYPTO_TFM_REQ_WEAK_KEY);
rc = crypto_blkcipher_setkey(*key_tfm, dummy_key, *key_size);
if (rc) {
printk(KERN_ERR "Error attempting to set key of size [%zd] for "
- "cipher [%s]; rc = [%d]\n", *key_size, cipher_name, rc);
+ "cipher [%s]; rc = [%d]\n", *key_size, full_alg_name,
+ rc);
rc = -EINVAL;
goto out;
}
(*encoded_name)[(*encoded_name_size)] = '\0';
(*encoded_name_size)++;
} else {
- rc = -ENOTSUPP;
+ rc = -EOPNOTSUPP;
}
if (rc) {
printk(KERN_ERR "%s: Error attempting to encode "
struct inode *lower_dir_inode = ecryptfs_inode_to_lower(dir);
struct dentry *lower_dir_dentry;
+ dget(lower_dentry);
lower_dir_dentry = lock_parent(lower_dentry);
rc = vfs_unlink(lower_dir_inode, lower_dentry);
if (rc) {
d_drop(dentry);
out_unlock:
unlock_dir(lower_dir_dentry);
+ dput(lower_dentry);
return rc;
}
&mount_crypt_stat->global_auth_tok_list,
mount_crypt_stat_list) {
if (memcmp(walker->sig, sig, ECRYPTFS_SIG_SIZE_HEX) == 0) {
- (*global_auth_tok) = walker;
+ rc = key_validate(walker->global_auth_tok_key);
+ if (!rc)
+ (*global_auth_tok) = walker;
goto out;
}
}
}
/* TODO: Support other key modules than passphrase for
* filename encryption */
- BUG_ON(s->auth_tok->token_type != ECRYPTFS_PASSWORD);
+ if (s->auth_tok->token_type != ECRYPTFS_PASSWORD) {
+ rc = -EOPNOTSUPP;
+ printk(KERN_INFO "%s: Filename encryption only supports "
+ "password tokens\n", __func__);
+ goto out_free_unlock;
+ }
sg_init_one(
&s->hash_sg,
(u8 *)s->auth_tok->token.password.session_key_encryption_key,
}
/* TODO: Support other key modules than passphrase for
* filename encryption */
- BUG_ON(s->auth_tok->token_type != ECRYPTFS_PASSWORD);
+ if (s->auth_tok->token_type != ECRYPTFS_PASSWORD) {
+ rc = -EOPNOTSUPP;
+ printk(KERN_INFO "%s: Filename encryption only supports "
+ "password tokens\n", __func__);
+ goto out_free_unlock;
+ }
rc = crypto_blkcipher_setkey(
s->desc.tfm,
s->auth_tok->token.password.session_key_encryption_key,
rc = -EINVAL;
goto out_free;
}
- ecryptfs_cipher_code_to_string(crypt_stat->cipher,
- (u16)data[(*packet_size)]);
+ rc = ecryptfs_cipher_code_to_string(crypt_stat->cipher,
+ (u16)data[(*packet_size)]);
+ if (rc)
+ goto out_free;
/* A little extra work to differentiate among the AES key
* sizes; see RFC2440 */
switch(data[(*packet_size)++]) {
crypt_stat->key_size =
(*new_auth_tok)->session_key.encrypted_key_size;
}
- ecryptfs_init_crypt_ctx(crypt_stat);
+ rc = ecryptfs_init_crypt_ctx(crypt_stat);
+ if (rc)
+ goto out_free;
if (unlikely(data[(*packet_size)++] != 0x03)) {
printk(KERN_WARNING "Only S2K ID 3 is currently supported\n");
rc = -ENOSYS;
int ecryptfs_add_keysig(struct ecryptfs_crypt_stat *crypt_stat, char *sig)
{
struct ecryptfs_key_sig *new_key_sig;
- int rc = 0;
new_key_sig = kmem_cache_alloc(ecryptfs_key_sig_cache, GFP_KERNEL);
if (!new_key_sig) {
- rc = -ENOMEM;
printk(KERN_ERR
"Error allocating from ecryptfs_key_sig_cache\n");
- goto out;
+ return -ENOMEM;
}
memcpy(new_key_sig->keysig, sig, ECRYPTFS_SIG_SIZE_HEX);
- mutex_lock(&crypt_stat->keysig_list_mutex);
+ /* Caller must hold keysig_list_mutex */
list_add(&new_key_sig->crypt_stat_list, &crypt_stat->keysig_list);
- mutex_unlock(&crypt_stat->keysig_list_mutex);
-out:
- return rc;
+
+ return 0;
}
struct kmem_cache *ecryptfs_global_auth_tok_cache;
const struct cred *cred)
{
struct ecryptfs_open_req *req;
+ int flags = O_LARGEFILE;
int rc = 0;
/* Corresponding dput() and mntput() are done when the
* destroyed. */
dget(lower_dentry);
mntget(lower_mnt);
- (*lower_file) = dentry_open(lower_dentry, lower_mnt,
- (O_RDWR | O_LARGEFILE), cred);
+ flags |= IS_RDONLY(lower_dentry->d_inode) ? O_RDONLY : O_RDWR;
+ (*lower_file) = dentry_open(lower_dentry, lower_mnt, flags, cred);
if (!IS_ERR(*lower_file))
goto out;
+ if (flags & O_RDONLY) {
+ rc = PTR_ERR((*lower_file));
+ goto out;
+ }
req = kmem_cache_alloc(ecryptfs_open_req_cache, GFP_KERNEL);
if (!req) {
rc = -ENOMEM;
__func__);
goto out_unlock;
}
- if (IS_ERR(*req->lower_file)) {
+ if (IS_ERR(*req->lower_file))
rc = PTR_ERR(*req->lower_file);
- dget(lower_dentry);
- mntget(lower_mnt);
- (*lower_file) = dentry_open(lower_dentry, lower_mnt,
- (O_RDONLY | O_LARGEFILE), cred);
- if (IS_ERR(*lower_file)) {
- rc = PTR_ERR(*req->lower_file);
- (*lower_file) = NULL;
- printk(KERN_WARNING "%s: Error attempting privileged "
- "open of lower file with either RW or RO "
- "perms; rc = [%d]. Giving up.\n",
- __func__, rc);
- }
- }
out_unlock:
mutex_unlock(&req->mux);
out_free:
lower_dentry = ecryptfs_dentry_to_lower(ecryptfs_dentry);
rc = ecryptfs_privileged_open(&inode_info->lower_file,
lower_dentry, lower_mnt, cred);
- if (rc || IS_ERR(inode_info->lower_file)) {
+ if (rc) {
printk(KERN_ERR "Error opening lower persistent file "
"for lower_dentry [0x%p] and lower_mnt [0x%p]; "
"rc = [%d]\n", lower_dentry, lower_mnt, rc);
- rc = PTR_ERR(inode_info->lower_file);
inode_info->lower_file = NULL;
}
}
rc = ecryptfs_write_lower(ecryptfs_inode, file_size_virt, 0,
sizeof(u64));
kfree(file_size_virt);
- if (rc)
+ if (rc < 0)
printk(KERN_ERR "%s: Error writing file size to header; "
"rc = [%d]\n", __func__, rc);
+ else
+ rc = 0;
out:
return rc;
}
*
* Write data to the lower file.
*
- * Returns zero on success; non-zero on error
+ * Returns bytes written on success; less than zero on error
*/
int ecryptfs_write_lower(struct inode *ecryptfs_inode, char *data,
loff_t offset, size_t size)
{
struct ecryptfs_inode_info *inode_info;
- ssize_t octets_written;
mm_segment_t fs_save;
- int rc = 0;
+ ssize_t rc;
inode_info = ecryptfs_inode_to_private(ecryptfs_inode);
mutex_lock(&inode_info->lower_file_mutex);
inode_info->lower_file->f_pos = offset;
fs_save = get_fs();
set_fs(get_ds());
- octets_written = vfs_write(inode_info->lower_file, data, size,
- &inode_info->lower_file->f_pos);
+ rc = vfs_write(inode_info->lower_file, data, size,
+ &inode_info->lower_file->f_pos);
set_fs(fs_save);
- if (octets_written < 0) {
- printk(KERN_ERR "%s: octets_written = [%td]; "
- "expected [%td]\n", __func__, octets_written, size);
- rc = -EINVAL;
- }
mutex_unlock(&inode_info->lower_file_mutex);
mark_inode_dirty_sync(ecryptfs_inode);
return rc;
+ offset_in_page);
virt = kmap(page_for_lower);
rc = ecryptfs_write_lower(ecryptfs_inode, virt, offset, size);
+ if (rc > 0)
+ rc = 0;
kunmap(page_for_lower);
return rc;
}
* Read @size bytes of data at byte offset @offset from the lower
* inode into memory location @data.
*
- * Returns zero on success; non-zero on error
+ * Returns bytes read on success; 0 on EOF; less than zero on error
*/
int ecryptfs_read_lower(char *data, loff_t offset, size_t size,
struct inode *ecryptfs_inode)
{
struct ecryptfs_inode_info *inode_info =
ecryptfs_inode_to_private(ecryptfs_inode);
- ssize_t octets_read;
mm_segment_t fs_save;
- int rc = 0;
+ ssize_t rc;
mutex_lock(&inode_info->lower_file_mutex);
BUG_ON(!inode_info->lower_file);
inode_info->lower_file->f_pos = offset;
fs_save = get_fs();
set_fs(get_ds());
- octets_read = vfs_read(inode_info->lower_file, data, size,
- &inode_info->lower_file->f_pos);
+ rc = vfs_read(inode_info->lower_file, data, size,
+ &inode_info->lower_file->f_pos);
set_fs(fs_save);
- if (octets_read < 0) {
- printk(KERN_ERR "%s: octets_read = [%td]; "
- "expected [%td]\n", __func__, octets_read, size);
- rc = -EINVAL;
- }
mutex_unlock(&inode_info->lower_file_mutex);
return rc;
}
offset = ((((loff_t)page_index) << PAGE_CACHE_SHIFT) + offset_in_page);
virt = kmap(page_for_ecryptfs);
rc = ecryptfs_read_lower(virt, offset, size, ecryptfs_inode);
+ if (rc > 0)
+ rc = 0;
kunmap(page_for_ecryptfs);
flush_dcache_page(page_for_ecryptfs);
return rc;
struct ecryptfs_inode_info *inode_info;
inode_info = ecryptfs_inode_to_private(inode);
- mutex_lock(&inode_info->lower_file_mutex);
if (inode_info->lower_file) {
struct dentry *lower_dentry =
inode_info->lower_file->f_dentry;
d_drop(lower_dentry);
}
}
- mutex_unlock(&inode_info->lower_file_mutex);
ecryptfs_destroy_crypt_stat(&inode_info->crypt_stat);
kmem_cache_free(ecryptfs_inode_info_cache, inode_info);
}
#include <linux/kmod.h>
#include <linux/fsnotify.h>
#include <linux/fs_struct.h>
+#include <linux/pipe_fs_i.h>
#include <asm/uaccess.h>
#include <asm/mmu_context.h>
int core_uses_pid;
char core_pattern[CORENAME_MAX_SIZE] = "core";
+unsigned int core_pipe_limit;
int suid_dumpable = 0;
/* The maximal length of core_pattern is also specified in sysctl.c */
return retval;
}
-int set_binfmt(struct linux_binfmt *new)
+void set_binfmt(struct linux_binfmt *new)
{
- struct linux_binfmt *old = current->binfmt;
+ struct mm_struct *mm = current->mm;
- if (new) {
- if (!try_module_get(new->module))
- return -1;
- }
- current->binfmt = new;
- if (old)
- module_put(old->module);
- return 0;
+ if (mm->binfmt)
+ module_put(mm->binfmt->module);
+
+ mm->binfmt = new;
+ if (new)
+ __module_get(new->module);
}
EXPORT_SYMBOL(set_binfmt);
return (ret >= 2) ? 2 : ret;
}
+static void wait_for_dump_helpers(struct file *file)
+{
+ struct pipe_inode_info *pipe;
+
+ pipe = file->f_path.dentry->d_inode->i_pipe;
+
+ pipe_lock(pipe);
+ pipe->readers++;
+ pipe->writers--;
+
+ while ((pipe->readers > 1) && (!signal_pending(current))) {
+ wake_up_interruptible_sync(&pipe->wait);
+ kill_fasync(&pipe->fasync_readers, SIGIO, POLL_IN);
+ pipe_wait(pipe);
+ }
+
+ pipe->readers--;
+ pipe->writers++;
+ pipe_unlock(pipe);
+
+}
+
+
void do_coredump(long signr, int exit_code, struct pt_regs *regs)
{
struct core_state core_state;
unsigned long core_limit = current->signal->rlim[RLIMIT_CORE].rlim_cur;
char **helper_argv = NULL;
int helper_argc = 0;
- char *delimit;
+ int dump_count = 0;
+ static atomic_t core_dump_count = ATOMIC_INIT(0);
audit_core_dumps(signr);
- binfmt = current->binfmt;
+ binfmt = mm->binfmt;
if (!binfmt || !binfmt->core_dump)
goto fail;
lock_kernel();
ispipe = format_corename(corename, signr);
unlock_kernel();
- /*
- * Don't bother to check the RLIMIT_CORE value if core_pattern points
- * to a pipe. Since we're not writing directly to the filesystem
- * RLIMIT_CORE doesn't really apply, as no actual core file will be
- * created unless the pipe reader choses to write out the core file
- * at which point file size limits and permissions will be imposed
- * as it does with any other process
- */
+
if ((!ispipe) && (core_limit < binfmt->min_coredump))
goto fail_unlock;
if (ispipe) {
+ if (core_limit == 0) {
+ /*
+ * Normally core limits are irrelevant to pipes, since
+ * we're not writing to the file system, but we use
+ * core_limit of 0 here as a speacial value. Any
+ * non-zero limit gets set to RLIM_INFINITY below, but
+ * a limit of 0 skips the dump. This is a consistent
+ * way to catch recursive crashes. We can still crash
+ * if the core_pattern binary sets RLIM_CORE = !0
+ * but it runs as root, and can do lots of stupid things
+ * Note that we use task_tgid_vnr here to grab the pid
+ * of the process group leader. That way we get the
+ * right pid if a thread in a multi-threaded
+ * core_pattern process dies.
+ */
+ printk(KERN_WARNING
+ "Process %d(%s) has RLIMIT_CORE set to 0\n",
+ task_tgid_vnr(current), current->comm);
+ printk(KERN_WARNING "Aborting core\n");
+ goto fail_unlock;
+ }
+
+ dump_count = atomic_inc_return(&core_dump_count);
+ if (core_pipe_limit && (core_pipe_limit < dump_count)) {
+ printk(KERN_WARNING "Pid %d(%s) over core_pipe_limit\n",
+ task_tgid_vnr(current), current->comm);
+ printk(KERN_WARNING "Skipping core dump\n");
+ goto fail_dropcount;
+ }
+
helper_argv = argv_split(GFP_KERNEL, corename+1, &helper_argc);
if (!helper_argv) {
printk(KERN_WARNING "%s failed to allocate memory\n",
__func__);
- goto fail_unlock;
- }
- /* Terminate the string before the first option */
- delimit = strchr(corename, ' ');
- if (delimit)
- *delimit = '\0';
- delimit = strrchr(helper_argv[0], '/');
- if (delimit)
- delimit++;
- else
- delimit = helper_argv[0];
- if (!strcmp(delimit, current->comm)) {
- printk(KERN_NOTICE "Recursive core dump detected, "
- "aborting\n");
- goto fail_unlock;
+ goto fail_dropcount;
}
core_limit = RLIM_INFINITY;
/* SIGPIPE can happen, but it's just never processed */
- if (call_usermodehelper_pipe(corename+1, helper_argv, NULL,
+ if (call_usermodehelper_pipe(helper_argv[0], helper_argv, NULL,
&file)) {
printk(KERN_INFO "Core dump to %s pipe failed\n",
corename);
- goto fail_unlock;
+ goto fail_dropcount;
}
} else
file = filp_open(corename,
O_CREAT | 2 | O_NOFOLLOW | O_LARGEFILE | flag,
0600);
if (IS_ERR(file))
- goto fail_unlock;
+ goto fail_dropcount;
inode = file->f_path.dentry->d_inode;
if (inode->i_nlink > 1)
goto close_fail; /* multiple links - don't dump */
if (retval)
current->signal->group_exit_code |= 0x80;
close_fail:
+ if (ispipe && core_pipe_limit)
+ wait_for_dump_helpers(file);
filp_close(file, NULL);
+fail_dropcount:
+ if (dump_count)
+ atomic_dec(&core_dump_count);
fail_unlock:
if (helper_argv)
argv_free(helper_argv);
}
lock_super(sb);
- lock_kernel();
sbi = sb->s_fs_info;
fscb->s_nextid = cpu_to_le64(sbi->s_nextid);
fscb->s_numfiles = cpu_to_le32(sbi->s_numfiles);
out:
if (or)
osd_end_request(or);
- unlock_kernel();
unlock_super(sb);
kfree(fscb);
return ret;
int num_pend;
struct exofs_sb_info *sbi = sb->s_fs_info;
- lock_kernel();
-
if (sb->s_dirt)
exofs_write_super(sb);
osduld_put_device(sbi->s_dev);
kfree(sb->s_fs_info);
sb->s_fs_info = NULL;
-
- unlock_kernel();
}
/*
.writepages = ext2_writepages,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
const struct address_space_operations ext2_aops_xip = {
.direct_IO = ext2_direct_IO,
.writepages = ext2_writepages,
.migratepage = buffer_migrate_page,
+ .error_remove_page = generic_error_remove_page,
};
/*
.direct_IO = ext3_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations ext3_writeback_aops = {
.direct_IO = ext3_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations ext3_journalled_aops = {
.invalidatepage = ext3_invalidatepage,
.releasepage = ext3_releasepage,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
void ext3_set_aops(struct inode *inode)
If unsure, say N.
-config EXT4DEV_COMPAT
- bool "Enable ext4dev compatibility"
- depends on EXT4_FS
- help
- Starting with 2.6.28, the name of the ext4 filesystem was
- renamed from ext4dev to ext4. Unfortunately there are some
- legacy userspace programs (such as klibc's fstype) have
- "ext4dev" hardcoded.
-
- To enable backwards compatibility so that systems that are
- still expecting to mount ext4 filesystems using ext4dev,
- choose Y here. This feature will go away by 2.6.31, so
- please arrange to get your userspace programs fixed!
-
config EXT4_FS_XATTR
bool "Ext4 extended attributes"
depends on EXT4_FS
/* data type for block group number */
typedef unsigned int ext4_group_t;
+/*
+ * Flags used in mballoc's allocation_context flags field.
+ *
+ * Also used to show what's going on for debugging purposes when the
+ * flag field is exported via the traceport interface
+ */
/* prefer goal again. length */
#define EXT4_MB_HINT_MERGE 0x0001
int pages_written;
int retval;
};
+#define DIO_AIO_UNWRITTEN 0x1
+typedef struct ext4_io_end {
+ struct list_head list; /* per-file finished AIO list */
+ struct inode *inode; /* file being written to */
+ unsigned int flag; /* unwritten or not */
+ int error; /* I/O error code */
+ ext4_lblk_t offset; /* offset in the file */
+ size_t size; /* size of the extent */
+ struct work_struct work; /* data work queue */
+} ext4_io_end_t;
/*
* Special inodes numbers
/* Call ext4_da_update_reserve_space() after successfully
allocating the blocks */
#define EXT4_GET_BLOCKS_UPDATE_RESERVE_SPACE 0x0008
-
+ /* caller is from the direct IO path, request to creation of an
+ unitialized extents if not allocated, split the uninitialized
+ extent if blocks has been preallocated already*/
+#define EXT4_GET_BLOCKS_DIO 0x0010
+#define EXT4_GET_BLOCKS_CONVERT 0x0020
+#define EXT4_GET_BLOCKS_DIO_CREATE_EXT (EXT4_GET_BLOCKS_DIO|\
+ EXT4_GET_BLOCKS_CREATE_UNINIT_EXT)
+ /* Convert extent to initialized after direct IO complete */
+#define EXT4_GET_BLOCKS_DIO_CONVERT_EXT (EXT4_GET_BLOCKS_CONVERT|\
+ EXT4_GET_BLOCKS_DIO_CREATE_EXT)
/*
* ioctl commands
static inline __le32 ext4_encode_extra_time(struct timespec *time)
{
return cpu_to_le32((sizeof(time->tv_sec) > 4 ?
- time->tv_sec >> 32 : 0) |
- ((time->tv_nsec << 2) & EXT4_NSEC_MASK));
+ (time->tv_sec >> 32) & EXT4_EPOCH_MASK : 0) |
+ ((time->tv_nsec << EXT4_EPOCH_BITS) & EXT4_NSEC_MASK));
}
static inline void ext4_decode_extra_time(struct timespec *time, __le32 extra)
if (sizeof(time->tv_sec) > 4)
time->tv_sec |= (__u64)(le32_to_cpu(extra) & EXT4_EPOCH_MASK)
<< 32;
- time->tv_nsec = (le32_to_cpu(extra) & EXT4_NSEC_MASK) >> 2;
+ time->tv_nsec = (le32_to_cpu(extra) & EXT4_NSEC_MASK) >> EXT4_EPOCH_BITS;
}
#define EXT4_INODE_SET_XTIME(xtime, inode, raw_inode) \
__u16 i_extra_isize;
spinlock_t i_block_reservation_lock;
+
+ /* completed async DIOs that might need unwritten extents handling */
+ struct list_head i_aio_dio_complete_list;
+ /* current io_end structure for async DIO write*/
+ ext4_io_end_t *cur_aio_dio;
};
/*
unsigned int s_mb_stats;
unsigned int s_mb_order2_reqs;
unsigned int s_mb_group_prealloc;
+ unsigned int s_max_writeback_mb_bump;
/* where last allocation was done - for stream allocation */
unsigned long s_mb_last_group;
unsigned long s_mb_last_start;
- /* history to debug policy */
- struct ext4_mb_history *s_mb_history;
- int s_mb_history_cur;
- int s_mb_history_max;
- int s_mb_history_num;
- spinlock_t s_mb_history_lock;
- int s_mb_history_filter;
-
/* stats for buddy allocator */
spinlock_t s_mb_pa_lock;
atomic_t s_bal_reqs; /* number of reqs with len > 1 */
unsigned int s_log_groups_per_flex;
struct flex_groups *s_flex_groups;
+
+ /* workqueue for dio unwritten */
+ struct workqueue_struct *dio_unwritten_wq;
};
static inline struct ext4_sb_info *EXT4_SB(struct super_block *sb)
struct address_space *mapping, loff_t from);
extern int ext4_page_mkwrite(struct vm_area_struct *vma, struct vm_fault *vmf);
extern qsize_t ext4_get_reserved_space(struct inode *inode);
-
+extern int flush_aio_dio_completed_IO(struct inode *inode);
/* ioctl.c */
extern long ext4_ioctl(struct file *, unsigned int, unsigned long);
extern long ext4_compat_ioctl(struct file *, unsigned int, unsigned long);
extern void ext4_ext_release(struct super_block *);
extern long ext4_fallocate(struct inode *inode, int mode, loff_t offset,
loff_t len);
+extern int ext4_convert_unwritten_extents(struct inode *inode, loff_t offset,
+ loff_t len);
extern int ext4_get_blocks(handle_t *handle, struct inode *inode,
sector_t block, unsigned int max_blocks,
struct buffer_head *bh, int flags);
(le16_to_cpu(ext->ee_len) - EXT_INIT_MAX_LEN));
}
+static inline void ext4_ext_mark_initialized(struct ext4_extent *ext)
+{
+ ext->ee_len = cpu_to_le16(ext4_ext_get_actual_len(ext));
+}
+
extern int ext4_ext_calc_metadata_amount(struct inode *inode, int blocks);
extern ext4_fsblk_t ext_pblock(struct ext4_extent *ex);
extern ext4_fsblk_t idx_pblock(struct ext4_extent_idx *);
struct ext4_ext_path *path,
struct ext4_extent *);
extern unsigned int ext4_ext_check_overlap(struct inode *, struct ext4_extent *, struct ext4_ext_path *);
-extern int ext4_ext_insert_extent(handle_t *, struct inode *, struct ext4_ext_path *, struct ext4_extent *);
+extern int ext4_ext_insert_extent(handle_t *, struct inode *, struct ext4_ext_path *, struct ext4_extent *, int);
extern int ext4_ext_walk_space(struct inode *, ext4_lblk_t, ext4_lblk_t,
ext_prepare_callback, void *);
extern struct ext4_ext_path *ext4_ext_find_extent(struct inode *, ext4_lblk_t,
handle_t *ext4_journal_start_sb(struct super_block *sb, int nblocks);
int __ext4_journal_stop(const char *where, handle_t *handle);
-#define EXT4_NOJOURNAL_HANDLE ((handle_t *) 0x1)
+#define EXT4_NOJOURNAL_MAX_REF_COUNT ((unsigned long) 4096)
+/* Note: Do not use this for NULL handles. This is only to determine if
+ * a properly allocated handle is using a journal or not. */
static inline int ext4_handle_valid(handle_t *handle)
{
- if (handle == EXT4_NOJOURNAL_HANDLE)
+ if ((unsigned long)handle < EXT4_NOJOURNAL_MAX_REF_COUNT)
return 0;
return 1;
}
* insert new index [@logical;@ptr] into the block at @curp;
* check where to insert: before @curp or after @curp
*/
-static int ext4_ext_insert_index(handle_t *handle, struct inode *inode,
+int ext4_ext_insert_index(handle_t *handle, struct inode *inode,
struct ext4_ext_path *curp,
int logical, ext4_fsblk_t ptr)
{
*/
int ext4_ext_insert_extent(handle_t *handle, struct inode *inode,
struct ext4_ext_path *path,
- struct ext4_extent *newext)
+ struct ext4_extent *newext, int flag)
{
struct ext4_extent_header *eh;
struct ext4_extent *ex, *fex;
BUG_ON(path[depth].p_hdr == NULL);
/* try to insert block into found extent and return */
- if (ex && ext4_can_extents_be_merged(inode, ex, newext)) {
+ if (ex && (flag != EXT4_GET_BLOCKS_DIO_CREATE_EXT)
+ && ext4_can_extents_be_merged(inode, ex, newext)) {
ext_debug("append [%d]%d block to %d:[%d]%d (from %llu)\n",
ext4_ext_is_uninitialized(newext),
ext4_ext_get_actual_len(newext),
merge:
/* try to merge extents to the right */
- ext4_ext_try_to_merge(inode, path, nearex);
+ if (flag != EXT4_GET_BLOCKS_DIO_CREATE_EXT)
+ ext4_ext_try_to_merge(inode, path, nearex);
/* try to merge extents to the left */
*/
if (EXT4_HAS_INCOMPAT_FEATURE(sb, EXT4_FEATURE_INCOMPAT_EXTENTS)) {
+#if defined(AGGRESSIVE_TEST) || defined(CHECK_BINSEARCH) || defined(EXTENTS_STATS)
printk(KERN_INFO "EXT4-fs: file extents enabled");
#ifdef AGGRESSIVE_TEST
printk(", aggressive tests");
printk(", stats");
#endif
printk("\n");
+#endif
#ifdef EXTENTS_STATS
spin_lock_init(&EXT4_SB(sb)->s_ext_stats_lock);
EXT4_SB(sb)->s_ext_min = 1 << 30;
}
#define EXT4_EXT_ZERO_LEN 7
-
/*
* This function is called by ext4_ext_get_blocks() if someone tries to write
* to an uninitialized extent. It may result in splitting the uninitialized
ex3->ee_block = cpu_to_le32(iblock);
ext4_ext_store_pblock(ex3, newblock);
ex3->ee_len = cpu_to_le16(allocated);
- err = ext4_ext_insert_extent(handle, inode, path, ex3);
+ err = ext4_ext_insert_extent(handle, inode, path,
+ ex3, 0);
if (err == -ENOSPC) {
err = ext4_ext_zeroout(inode, &orig_ex);
if (err)
ext4_ext_store_pblock(ex3, newblock + max_blocks);
ex3->ee_len = cpu_to_le16(allocated - max_blocks);
ext4_ext_mark_uninitialized(ex3);
- err = ext4_ext_insert_extent(handle, inode, path, ex3);
+ err = ext4_ext_insert_extent(handle, inode, path, ex3, 0);
if (err == -ENOSPC) {
err = ext4_ext_zeroout(inode, &orig_ex);
if (err)
err = ext4_ext_dirty(handle, inode, path + depth);
goto out;
insert:
- err = ext4_ext_insert_extent(handle, inode, path, &newex);
+ err = ext4_ext_insert_extent(handle, inode, path, &newex, 0);
if (err == -ENOSPC) {
err = ext4_ext_zeroout(inode, &orig_ex);
if (err)
return err;
}
+/*
+ * This function is called by ext4_ext_get_blocks() from
+ * ext4_get_blocks_dio_write() when DIO to write
+ * to an uninitialized extent.
+ *
+ * Writing to an uninitized extent may result in splitting the uninitialized
+ * extent into multiple /intialized unintialized extents (up to three)
+ * There are three possibilities:
+ * a> There is no split required: Entire extent should be uninitialized
+ * b> Splits in two extents: Write is happening at either end of the extent
+ * c> Splits in three extents: Somone is writing in middle of the extent
+ *
+ * One of more index blocks maybe needed if the extent tree grow after
+ * the unintialized extent split. To prevent ENOSPC occur at the IO
+ * complete, we need to split the uninitialized extent before DIO submit
+ * the IO. The uninitilized extent called at this time will be split
+ * into three uninitialized extent(at most). After IO complete, the part
+ * being filled will be convert to initialized by the end_io callback function
+ * via ext4_convert_unwritten_extents().
+ */
+static int ext4_split_unwritten_extents(handle_t *handle,
+ struct inode *inode,
+ struct ext4_ext_path *path,
+ ext4_lblk_t iblock,
+ unsigned int max_blocks,
+ int flags)
+{
+ struct ext4_extent *ex, newex, orig_ex;
+ struct ext4_extent *ex1 = NULL;
+ struct ext4_extent *ex2 = NULL;
+ struct ext4_extent *ex3 = NULL;
+ struct ext4_extent_header *eh;
+ ext4_lblk_t ee_block;
+ unsigned int allocated, ee_len, depth;
+ ext4_fsblk_t newblock;
+ int err = 0;
+ int ret = 0;
+
+ ext_debug("ext4_split_unwritten_extents: inode %lu,"
+ "iblock %llu, max_blocks %u\n", inode->i_ino,
+ (unsigned long long)iblock, max_blocks);
+ depth = ext_depth(inode);
+ eh = path[depth].p_hdr;
+ ex = path[depth].p_ext;
+ ee_block = le32_to_cpu(ex->ee_block);
+ ee_len = ext4_ext_get_actual_len(ex);
+ allocated = ee_len - (iblock - ee_block);
+ newblock = iblock - ee_block + ext_pblock(ex);
+ ex2 = ex;
+ orig_ex.ee_block = ex->ee_block;
+ orig_ex.ee_len = cpu_to_le16(ee_len);
+ ext4_ext_store_pblock(&orig_ex, ext_pblock(ex));
+
+ /*
+ * if the entire unintialized extent length less than
+ * the size of extent to write, there is no need to split
+ * uninitialized extent
+ */
+ if (allocated <= max_blocks)
+ return ret;
+
+ err = ext4_ext_get_access(handle, inode, path + depth);
+ if (err)
+ goto out;
+ /* ex1: ee_block to iblock - 1 : uninitialized */
+ if (iblock > ee_block) {
+ ex1 = ex;
+ ex1->ee_len = cpu_to_le16(iblock - ee_block);
+ ext4_ext_mark_uninitialized(ex1);
+ ex2 = &newex;
+ }
+ /*
+ * for sanity, update the length of the ex2 extent before
+ * we insert ex3, if ex1 is NULL. This is to avoid temporary
+ * overlap of blocks.
+ */
+ if (!ex1 && allocated > max_blocks)
+ ex2->ee_len = cpu_to_le16(max_blocks);
+ /* ex3: to ee_block + ee_len : uninitialised */
+ if (allocated > max_blocks) {
+ unsigned int newdepth;
+ ex3 = &newex;
+ ex3->ee_block = cpu_to_le32(iblock + max_blocks);
+ ext4_ext_store_pblock(ex3, newblock + max_blocks);
+ ex3->ee_len = cpu_to_le16(allocated - max_blocks);
+ ext4_ext_mark_uninitialized(ex3);
+ err = ext4_ext_insert_extent(handle, inode, path, ex3, flags);
+ if (err == -ENOSPC) {
+ err = ext4_ext_zeroout(inode, &orig_ex);
+ if (err)
+ goto fix_extent_len;
+ /* update the extent length and mark as initialized */
+ ex->ee_block = orig_ex.ee_block;
+ ex->ee_len = orig_ex.ee_len;
+ ext4_ext_store_pblock(ex, ext_pblock(&orig_ex));
+ ext4_ext_dirty(handle, inode, path + depth);
+ /* zeroed the full extent */
+ /* blocks available from iblock */
+ return allocated;
+
+ } else if (err)
+ goto fix_extent_len;
+ /*
+ * The depth, and hence eh & ex might change
+ * as part of the insert above.
+ */
+ newdepth = ext_depth(inode);
+ /*
+ * update the extent length after successful insert of the
+ * split extent
+ */
+ orig_ex.ee_len = cpu_to_le16(ee_len -
+ ext4_ext_get_actual_len(ex3));
+ depth = newdepth;
+ ext4_ext_drop_refs(path);
+ path = ext4_ext_find_extent(inode, iblock, path);
+ if (IS_ERR(path)) {
+ err = PTR_ERR(path);
+ goto out;
+ }
+ eh = path[depth].p_hdr;
+ ex = path[depth].p_ext;
+ if (ex2 != &newex)
+ ex2 = ex;
+
+ err = ext4_ext_get_access(handle, inode, path + depth);
+ if (err)
+ goto out;
+
+ allocated = max_blocks;
+ }
+ /*
+ * If there was a change of depth as part of the
+ * insertion of ex3 above, we need to update the length
+ * of the ex1 extent again here
+ */
+ if (ex1 && ex1 != ex) {
+ ex1 = ex;
+ ex1->ee_len = cpu_to_le16(iblock - ee_block);
+ ext4_ext_mark_uninitialized(ex1);
+ ex2 = &newex;
+ }
+ /*
+ * ex2: iblock to iblock + maxblocks-1 : to be direct IO written,
+ * uninitialised still.
+ */
+ ex2->ee_block = cpu_to_le32(iblock);
+ ext4_ext_store_pblock(ex2, newblock);
+ ex2->ee_len = cpu_to_le16(allocated);
+ ext4_ext_mark_uninitialized(ex2);
+ if (ex2 != ex)
+ goto insert;
+ /* Mark modified extent as dirty */
+ err = ext4_ext_dirty(handle, inode, path + depth);
+ ext_debug("out here\n");
+ goto out;
+insert:
+ err = ext4_ext_insert_extent(handle, inode, path, &newex, flags);
+ if (err == -ENOSPC) {
+ err = ext4_ext_zeroout(inode, &orig_ex);
+ if (err)
+ goto fix_extent_len;
+ /* update the extent length and mark as initialized */
+ ex->ee_block = orig_ex.ee_block;
+ ex->ee_len = orig_ex.ee_len;
+ ext4_ext_store_pblock(ex, ext_pblock(&orig_ex));
+ ext4_ext_dirty(handle, inode, path + depth);
+ /* zero out the first half */
+ return allocated;
+ } else if (err)
+ goto fix_extent_len;
+out:
+ ext4_ext_show_leaf(inode, path);
+ return err ? err : allocated;
+
+fix_extent_len:
+ ex->ee_block = orig_ex.ee_block;
+ ex->ee_len = orig_ex.ee_len;
+ ext4_ext_store_pblock(ex, ext_pblock(&orig_ex));
+ ext4_ext_mark_uninitialized(ex);
+ ext4_ext_dirty(handle, inode, path + depth);
+ return err;
+}
+static int ext4_convert_unwritten_extents_dio(handle_t *handle,
+ struct inode *inode,
+ struct ext4_ext_path *path)
+{
+ struct ext4_extent *ex;
+ struct ext4_extent_header *eh;
+ int depth;
+ int err = 0;
+ int ret = 0;
+
+ depth = ext_depth(inode);
+ eh = path[depth].p_hdr;
+ ex = path[depth].p_ext;
+
+ err = ext4_ext_get_access(handle, inode, path + depth);
+ if (err)
+ goto out;
+ /* first mark the extent as initialized */
+ ext4_ext_mark_initialized(ex);
+
+ /*
+ * We have to see if it can be merged with the extent
+ * on the left.
+ */
+ if (ex > EXT_FIRST_EXTENT(eh)) {
+ /*
+ * To merge left, pass "ex - 1" to try_to_merge(),
+ * since it merges towards right _only_.
+ */
+ ret = ext4_ext_try_to_merge(inode, path, ex - 1);
+ if (ret) {
+ err = ext4_ext_correct_indexes(handle, inode, path);
+ if (err)
+ goto out;
+ depth = ext_depth(inode);
+ ex--;
+ }
+ }
+ /*
+ * Try to Merge towards right.
+ */
+ ret = ext4_ext_try_to_merge(inode, path, ex);
+ if (ret) {
+ err = ext4_ext_correct_indexes(handle, inode, path);
+ if (err)
+ goto out;
+ depth = ext_depth(inode);
+ }
+ /* Mark modified extent as dirty */
+ err = ext4_ext_dirty(handle, inode, path + depth);
+out:
+ ext4_ext_show_leaf(inode, path);
+ return err;
+}
+
+static int
+ext4_ext_handle_uninitialized_extents(handle_t *handle, struct inode *inode,
+ ext4_lblk_t iblock, unsigned int max_blocks,
+ struct ext4_ext_path *path, int flags,
+ unsigned int allocated, struct buffer_head *bh_result,
+ ext4_fsblk_t newblock)
+{
+ int ret = 0;
+ int err = 0;
+ ext4_io_end_t *io = EXT4_I(inode)->cur_aio_dio;
+
+ ext_debug("ext4_ext_handle_uninitialized_extents: inode %lu, logical"
+ "block %llu, max_blocks %u, flags %d, allocated %u",
+ inode->i_ino, (unsigned long long)iblock, max_blocks,
+ flags, allocated);
+ ext4_ext_show_leaf(inode, path);
+
+ /* DIO get_block() before submit the IO, split the extent */
+ if (flags == EXT4_GET_BLOCKS_DIO_CREATE_EXT) {
+ ret = ext4_split_unwritten_extents(handle,
+ inode, path, iblock,
+ max_blocks, flags);
+ /* flag the io_end struct that we need convert when IO done */
+ if (io)
+ io->flag = DIO_AIO_UNWRITTEN;
+ goto out;
+ }
+ /* DIO end_io complete, convert the filled extent to written */
+ if (flags == EXT4_GET_BLOCKS_DIO_CONVERT_EXT) {
+ ret = ext4_convert_unwritten_extents_dio(handle, inode,
+ path);
+ goto out2;
+ }
+ /* buffered IO case */
+ /*
+ * repeat fallocate creation request
+ * we already have an unwritten extent
+ */
+ if (flags & EXT4_GET_BLOCKS_UNINIT_EXT)
+ goto map_out;
+
+ /* buffered READ or buffered write_begin() lookup */
+ if ((flags & EXT4_GET_BLOCKS_CREATE) == 0) {
+ /*
+ * We have blocks reserved already. We
+ * return allocated blocks so that delalloc
+ * won't do block reservation for us. But
+ * the buffer head will be unmapped so that
+ * a read from the block returns 0s.
+ */
+ set_buffer_unwritten(bh_result);
+ goto out1;
+ }
+
+ /* buffered write, writepage time, convert*/
+ ret = ext4_ext_convert_to_initialized(handle, inode,
+ path, iblock,
+ max_blocks);
+out:
+ if (ret <= 0) {
+ err = ret;
+ goto out2;
+ } else
+ allocated = ret;
+ set_buffer_new(bh_result);
+map_out:
+ set_buffer_mapped(bh_result);
+out1:
+ if (allocated > max_blocks)
+ allocated = max_blocks;
+ ext4_ext_show_leaf(inode, path);
+ bh_result->b_bdev = inode->i_sb->s_bdev;
+ bh_result->b_blocknr = newblock;
+out2:
+ if (path) {
+ ext4_ext_drop_refs(path);
+ kfree(path);
+ }
+ return err ? err : allocated;
+}
/*
* Block allocation/map/preallocation routine for extents based files
*
int err = 0, depth, ret, cache_type;
unsigned int allocated = 0;
struct ext4_allocation_request ar;
+ ext4_io_end_t *io = EXT4_I(inode)->cur_aio_dio;
__clear_bit(BH_New, &bh_result->b_state);
ext_debug("blocks %u/%u requested for inode %lu\n",
EXT4_EXT_CACHE_EXTENT);
goto out;
}
- if (flags & EXT4_GET_BLOCKS_UNINIT_EXT)
- goto out;
- if ((flags & EXT4_GET_BLOCKS_CREATE) == 0) {
- if (allocated > max_blocks)
- allocated = max_blocks;
- /*
- * We have blocks reserved already. We
- * return allocated blocks so that delalloc
- * won't do block reservation for us. But
- * the buffer head will be unmapped so that
- * a read from the block returns 0s.
- */
- set_buffer_unwritten(bh_result);
- bh_result->b_bdev = inode->i_sb->s_bdev;
- bh_result->b_blocknr = newblock;
- goto out2;
- }
-
- ret = ext4_ext_convert_to_initialized(handle, inode,
- path, iblock,
- max_blocks);
- if (ret <= 0) {
- err = ret;
- goto out2;
- } else
- allocated = ret;
- goto outnew;
+ ret = ext4_ext_handle_uninitialized_extents(handle,
+ inode, iblock, max_blocks, path,
+ flags, allocated, bh_result, newblock);
+ return ret;
}
}
/* try to insert new extent into found leaf and return */
ext4_ext_store_pblock(&newex, newblock);
newex.ee_len = cpu_to_le16(ar.len);
- if (flags & EXT4_GET_BLOCKS_UNINIT_EXT) /* Mark uninitialized */
+ /* Mark uninitialized */
+ if (flags & EXT4_GET_BLOCKS_UNINIT_EXT){
ext4_ext_mark_uninitialized(&newex);
- err = ext4_ext_insert_extent(handle, inode, path, &newex);
+ /*
+ * io_end structure was created for every async
+ * direct IO write to the middle of the file.
+ * To avoid unecessary convertion for every aio dio rewrite
+ * to the mid of file, here we flag the IO that is really
+ * need the convertion.
+ *
+ */
+ if (io && flags == EXT4_GET_BLOCKS_DIO_CREATE_EXT)
+ io->flag = DIO_AIO_UNWRITTEN;
+ }
+ err = ext4_ext_insert_extent(handle, inode, path, &newex, flags);
if (err) {
/* free data blocks we just allocated */
/* not a good idea to call discard here directly,
/* previous routine could use block we allocated */
newblock = ext_pblock(&newex);
allocated = ext4_ext_get_actual_len(&newex);
-outnew:
set_buffer_new(bh_result);
/* Cache only when it is _not_ an uninitialized extent */
return ret > 0 ? ret2 : ret;
}
+/*
+ * This function convert a range of blocks to written extents
+ * The caller of this function will pass the start offset and the size.
+ * all unwritten extents within this range will be converted to
+ * written extents.
+ *
+ * This function is called from the direct IO end io call back
+ * function, to convert the fallocated extents after IO is completed.
+ */
+int ext4_convert_unwritten_extents(struct inode *inode, loff_t offset,
+ loff_t len)
+{
+ handle_t *handle;
+ ext4_lblk_t block;
+ unsigned int max_blocks;
+ int ret = 0;
+ int ret2 = 0;
+ struct buffer_head map_bh;
+ unsigned int credits, blkbits = inode->i_blkbits;
+
+ block = offset >> blkbits;
+ /*
+ * We can't just convert len to max_blocks because
+ * If blocksize = 4096 offset = 3072 and len = 2048
+ */
+ max_blocks = (EXT4_BLOCK_ALIGN(len + offset, blkbits) >> blkbits)
+ - block;
+ /*
+ * credits to insert 1 extent into extent tree
+ */
+ credits = ext4_chunk_trans_blocks(inode, max_blocks);
+ while (ret >= 0 && ret < max_blocks) {
+ block = block + ret;
+ max_blocks = max_blocks - ret;
+ handle = ext4_journal_start(inode, credits);
+ if (IS_ERR(handle)) {
+ ret = PTR_ERR(handle);
+ break;
+ }
+ map_bh.b_state = 0;
+ ret = ext4_get_blocks(handle, inode, block,
+ max_blocks, &map_bh,
+ EXT4_GET_BLOCKS_DIO_CONVERT_EXT);
+ if (ret <= 0) {
+ WARN_ON(ret <= 0);
+ printk(KERN_ERR "%s: ext4_ext_get_blocks "
+ "returned error inode#%lu, block=%u, "
+ "max_blocks=%u", __func__,
+ inode->i_ino, block, max_blocks);
+ }
+ ext4_mark_inode_dirty(handle, inode);
+ ret2 = ext4_journal_stop(handle);
+ if (ret <= 0 || ret2 )
+ break;
+ }
+ return ret > 0 ? ret2 : ret;
+}
/*
* Callback function called for each extent to gather FIEMAP information.
*/
return generic_file_aio_write(iocb, iov, nr_segs, pos);
}
-static struct vm_operations_struct ext4_file_vm_ops = {
+static const struct vm_operations_struct ext4_file_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = ext4_page_mkwrite,
};
*
* What we do is just kick off a commit and wait on it. This will snapshot the
* inode to disk.
+ *
+ * i_mutex lock is held when entering and exiting this function
*/
int ext4_sync_file(struct file *file, struct dentry *dentry, int datasync)
trace_ext4_sync_file(file, dentry, datasync);
+ ret = flush_aio_dio_completed_IO(inode);
+ if (ret < 0)
+ goto out;
/*
* data=writeback:
* The caller's filemap_fdatawrite()/wait will sync the data.
#include <linux/namei.h>
#include <linux/uio.h>
#include <linux/bio.h>
+#include <linux/workqueue.h>
#include "ext4_jbd2.h"
#include "xattr.h"
return 0;
}
+/*
+ * Return the number of contiguous dirty pages in a given inode
+ * starting at page frame idx.
+ */
+static pgoff_t ext4_num_dirty_pages(struct inode *inode, pgoff_t idx,
+ unsigned int max_pages)
+{
+ struct address_space *mapping = inode->i_mapping;
+ pgoff_t index;
+ struct pagevec pvec;
+ pgoff_t num = 0;
+ int i, nr_pages, done = 0;
+
+ if (max_pages == 0)
+ return 0;
+ pagevec_init(&pvec, 0);
+ while (!done) {
+ index = idx;
+ nr_pages = pagevec_lookup_tag(&pvec, mapping, &index,
+ PAGECACHE_TAG_DIRTY,
+ (pgoff_t)PAGEVEC_SIZE);
+ if (nr_pages == 0)
+ break;
+ for (i = 0; i < nr_pages; i++) {
+ struct page *page = pvec.pages[i];
+ struct buffer_head *bh, *head;
+
+ lock_page(page);
+ if (unlikely(page->mapping != mapping) ||
+ !PageDirty(page) ||
+ PageWriteback(page) ||
+ page->index != idx) {
+ done = 1;
+ unlock_page(page);
+ break;
+ }
+ if (page_has_buffers(page)) {
+ bh = head = page_buffers(page);
+ do {
+ if (!buffer_delay(bh) &&
+ !buffer_unwritten(bh))
+ done = 1;
+ bh = bh->b_this_page;
+ } while (!done && (bh != head));
+ }
+ unlock_page(page);
+ if (done)
+ break;
+ idx++;
+ num++;
+ if (num >= max_pages)
+ break;
+ }
+ pagevec_release(&pvec);
+ }
+ return num;
+}
+
/*
* The ext4_get_blocks() function tries to look up the requested blocks,
* and returns if the blocks are already mapped.
clear_buffer_mapped(bh);
clear_buffer_unwritten(bh);
+ ext_debug("ext4_get_blocks(): inode %lu, flag %d, max_blocks %u,"
+ "logical block %lu\n", inode->i_ino, flags, max_blocks,
+ (unsigned long)block);
/*
* Try to see if we can get the block without requesting a new
* file system block.
if (ext4_claim_free_blocks(sbi, total)) {
spin_unlock(&EXT4_I(inode)->i_block_reservation_lock);
+ vfs_dq_release_reservation_block(inode, total);
if (ext4_should_retry_alloc(inode->i_sb, &retries)) {
yield();
goto repeat;
}
- vfs_dq_release_reservation_block(inode, total);
return -ENOSPC;
}
EXT4_I(inode)->i_reserved_data_blocks += nrblocks;
static void ext4_print_free_blocks(struct inode *inode)
{
struct ext4_sb_info *sbi = EXT4_SB(inode->i_sb);
- printk(KERN_EMERG "Total free blocks count %lld\n",
- ext4_count_free_blocks(inode->i_sb));
- printk(KERN_EMERG "Free/Dirty block details\n");
- printk(KERN_EMERG "free_blocks=%lld\n",
- (long long)percpu_counter_sum(&sbi->s_freeblocks_counter));
- printk(KERN_EMERG "dirty_blocks=%lld\n",
- (long long)percpu_counter_sum(&sbi->s_dirtyblocks_counter));
- printk(KERN_EMERG "Block reservation details\n");
- printk(KERN_EMERG "i_reserved_data_blocks=%u\n",
- EXT4_I(inode)->i_reserved_data_blocks);
- printk(KERN_EMERG "i_reserved_meta_blocks=%u\n",
- EXT4_I(inode)->i_reserved_meta_blocks);
+ printk(KERN_CRIT "Total free blocks count %lld\n",
+ ext4_count_free_blocks(inode->i_sb));
+ printk(KERN_CRIT "Free/Dirty block details\n");
+ printk(KERN_CRIT "free_blocks=%lld\n",
+ (long long) percpu_counter_sum(&sbi->s_freeblocks_counter));
+ printk(KERN_CRIT "dirty_blocks=%lld\n",
+ (long long) percpu_counter_sum(&sbi->s_dirtyblocks_counter));
+ printk(KERN_CRIT "Block reservation details\n");
+ printk(KERN_CRIT "i_reserved_data_blocks=%u\n",
+ EXT4_I(inode)->i_reserved_data_blocks);
+ printk(KERN_CRIT "i_reserved_meta_blocks=%u\n",
+ EXT4_I(inode)->i_reserved_meta_blocks);
return;
}
* writepage and writepages will again try to write
* the same.
*/
- printk(KERN_EMERG "%s block allocation failed for inode %lu "
- "at logical offset %llu with max blocks "
- "%zd with error %d\n",
- __func__, mpd->inode->i_ino,
- (unsigned long long)next,
- mpd->b_size >> mpd->inode->i_blkbits, err);
- printk(KERN_EMERG "This should not happen.!! "
- "Data will be lost\n");
+ ext4_msg(mpd->inode->i_sb, KERN_CRIT,
+ "delayed block allocation failed for inode %lu at "
+ "logical offset %llu with max blocks %zd with "
+ "error %d\n", mpd->inode->i_ino,
+ (unsigned long long) next,
+ mpd->b_size >> mpd->inode->i_blkbits, err);
+ printk(KERN_CRIT "This should not happen!! "
+ "Data will be lost\n");
if (err == -ENOSPC) {
ext4_print_free_blocks(mpd->inode);
}
int no_nrwrite_index_update;
int pages_written = 0;
long pages_skipped;
+ unsigned int max_pages;
int range_cyclic, cycled = 1, io_done = 0;
- int needed_blocks, ret = 0, nr_to_writebump = 0;
+ int needed_blocks, ret = 0;
+ long desired_nr_to_write, nr_to_writebump = 0;
loff_t range_start = wbc->range_start;
struct ext4_sb_info *sbi = EXT4_SB(mapping->host->i_sb);
if (unlikely(sbi->s_mount_flags & EXT4_MF_FS_ABORTED))
return -EROFS;
- /*
- * Make sure nr_to_write is >= sbi->s_mb_stream_request
- * This make sure small files blocks are allocated in
- * single attempt. This ensure that small files
- * get less fragmented.
- */
- if (wbc->nr_to_write < sbi->s_mb_stream_request) {
- nr_to_writebump = sbi->s_mb_stream_request - wbc->nr_to_write;
- wbc->nr_to_write = sbi->s_mb_stream_request;
- }
if (wbc->range_start == 0 && wbc->range_end == LLONG_MAX)
range_whole = 1;
} else
index = wbc->range_start >> PAGE_CACHE_SHIFT;
+ /*
+ * This works around two forms of stupidity. The first is in
+ * the writeback code, which caps the maximum number of pages
+ * written to be 1024 pages. This is wrong on multiple
+ * levels; different architectues have a different page size,
+ * which changes the maximum amount of data which gets
+ * written. Secondly, 4 megabytes is way too small. XFS
+ * forces this value to be 16 megabytes by multiplying
+ * nr_to_write parameter by four, and then relies on its
+ * allocator to allocate larger extents to make them
+ * contiguous. Unfortunately this brings us to the second
+ * stupidity, which is that ext4's mballoc code only allocates
+ * at most 2048 blocks. So we force contiguous writes up to
+ * the number of dirty blocks in the inode, or
+ * sbi->max_writeback_mb_bump whichever is smaller.
+ */
+ max_pages = sbi->s_max_writeback_mb_bump << (20 - PAGE_CACHE_SHIFT);
+ if (!range_cyclic && range_whole)
+ desired_nr_to_write = wbc->nr_to_write * 8;
+ else
+ desired_nr_to_write = ext4_num_dirty_pages(inode, index,
+ max_pages);
+ if (desired_nr_to_write > max_pages)
+ desired_nr_to_write = max_pages;
+
+ if (wbc->nr_to_write < desired_nr_to_write) {
+ nr_to_writebump = desired_nr_to_write - wbc->nr_to_write;
+ wbc->nr_to_write = desired_nr_to_write;
+ }
+
mpd.wbc = wbc;
mpd.inode = mapping->host;
handle = ext4_journal_start(inode, needed_blocks);
if (IS_ERR(handle)) {
ret = PTR_ERR(handle);
- printk(KERN_CRIT "%s: jbd2_start: "
+ ext4_msg(inode->i_sb, KERN_CRIT, "%s: jbd2_start: "
"%ld pages, ino %lu; err %d\n", __func__,
wbc->nr_to_write, inode->i_ino, ret);
- dump_stack();
goto out_writepages;
}
goto retry;
}
if (pages_skipped != wbc->pages_skipped)
- printk(KERN_EMERG "This should not happen leaving %s "
- "with nr_to_write = %ld ret = %d\n",
- __func__, wbc->nr_to_write, ret);
+ ext4_msg(inode->i_sb, KERN_CRIT,
+ "This should not happen leaving %s "
+ "with nr_to_write = %ld ret = %d\n",
+ __func__, wbc->nr_to_write, ret);
/* Update index */
index += pages_written;
out_writepages:
if (!no_nrwrite_index_update)
wbc->no_nrwrite_index_update = 0;
- wbc->nr_to_write -= nr_to_writebump;
+ if (wbc->nr_to_write > nr_to_writebump)
+ wbc->nr_to_write -= nr_to_writebump;
wbc->range_start = range_start;
trace_ext4_da_writepages_result(inode, wbc, ret, pages_written);
return ret;
}
/*
+ * O_DIRECT for ext3 (or indirect map) based files
+ *
* If the O_DIRECT write will extend the file then add this inode to the
* orphan list. So recovery will truncate it back to the original size
* if the machine crashes during the write.
* crashes then stale disk data _may_ be exposed inside the file. But current
* VFS code falls back into buffered path in that case so we are safe.
*/
-static ssize_t ext4_direct_IO(int rw, struct kiocb *iocb,
+static ssize_t ext4_ind_direct_IO(int rw, struct kiocb *iocb,
const struct iovec *iov, loff_t offset,
unsigned long nr_segs)
{
ssize_t ret;
int orphan = 0;
size_t count = iov_length(iov, nr_segs);
+ int retries = 0;
if (rw == WRITE) {
loff_t final_size = offset + count;
}
}
+retry:
ret = blockdev_direct_IO(rw, iocb, inode, inode->i_sb->s_bdev, iov,
offset, nr_segs,
ext4_get_block, NULL);
+ if (ret == -ENOSPC && ext4_should_retry_alloc(inode->i_sb, &retries))
+ goto retry;
if (orphan) {
int err;
return ret;
}
+/* Maximum number of blocks we map for direct IO at once. */
+
+static int ext4_get_block_dio_write(struct inode *inode, sector_t iblock,
+ struct buffer_head *bh_result, int create)
+{
+ handle_t *handle = NULL;
+ int ret = 0;
+ unsigned max_blocks = bh_result->b_size >> inode->i_blkbits;
+ int dio_credits;
+
+ ext4_debug("ext4_get_block_dio_write: inode %lu, create flag %d\n",
+ inode->i_ino, create);
+ /*
+ * DIO VFS code passes create = 0 flag for write to
+ * the middle of file. It does this to avoid block
+ * allocation for holes, to prevent expose stale data
+ * out when there is parallel buffered read (which does
+ * not hold the i_mutex lock) while direct IO write has
+ * not completed. DIO request on holes finally falls back
+ * to buffered IO for this reason.
+ *
+ * For ext4 extent based file, since we support fallocate,
+ * new allocated extent as uninitialized, for holes, we
+ * could fallocate blocks for holes, thus parallel
+ * buffered IO read will zero out the page when read on
+ * a hole while parallel DIO write to the hole has not completed.
+ *
+ * when we come here, we know it's a direct IO write to
+ * to the middle of file (<i_size)
+ * so it's safe to override the create flag from VFS.
+ */
+ create = EXT4_GET_BLOCKS_DIO_CREATE_EXT;
+
+ if (max_blocks > DIO_MAX_BLOCKS)
+ max_blocks = DIO_MAX_BLOCKS;
+ dio_credits = ext4_chunk_trans_blocks(inode, max_blocks);
+ handle = ext4_journal_start(inode, dio_credits);
+ if (IS_ERR(handle)) {
+ ret = PTR_ERR(handle);
+ goto out;
+ }
+ ret = ext4_get_blocks(handle, inode, iblock, max_blocks, bh_result,
+ create);
+ if (ret > 0) {
+ bh_result->b_size = (ret << inode->i_blkbits);
+ ret = 0;
+ }
+ ext4_journal_stop(handle);
+out:
+ return ret;
+}
+
+static void ext4_free_io_end(ext4_io_end_t *io)
+{
+ BUG_ON(!io);
+ iput(io->inode);
+ kfree(io);
+}
+static void dump_aio_dio_list(struct inode * inode)
+{
+#ifdef EXT4_DEBUG
+ struct list_head *cur, *before, *after;
+ ext4_io_end_t *io, *io0, *io1;
+
+ if (list_empty(&EXT4_I(inode)->i_aio_dio_complete_list)){
+ ext4_debug("inode %lu aio dio list is empty\n", inode->i_ino);
+ return;
+ }
+
+ ext4_debug("Dump inode %lu aio_dio_completed_IO list \n", inode->i_ino);
+ list_for_each_entry(io, &EXT4_I(inode)->i_aio_dio_complete_list, list){
+ cur = &io->list;
+ before = cur->prev;
+ io0 = container_of(before, ext4_io_end_t, list);
+ after = cur->next;
+ io1 = container_of(after, ext4_io_end_t, list);
+
+ ext4_debug("io 0x%p from inode %lu,prev 0x%p,next 0x%p\n",
+ io, inode->i_ino, io0, io1);
+ }
+#endif
+}
+
+/*
+ * check a range of space and convert unwritten extents to written.
+ */
+static int ext4_end_aio_dio_nolock(ext4_io_end_t *io)
+{
+ struct inode *inode = io->inode;
+ loff_t offset = io->offset;
+ size_t size = io->size;
+ int ret = 0;
+
+ ext4_debug("end_aio_dio_onlock: io 0x%p from inode %lu,list->next 0x%p,"
+ "list->prev 0x%p\n",
+ io, inode->i_ino, io->list.next, io->list.prev);
+
+ if (list_empty(&io->list))
+ return ret;
+
+ if (io->flag != DIO_AIO_UNWRITTEN)
+ return ret;
+
+ if (offset + size <= i_size_read(inode))
+ ret = ext4_convert_unwritten_extents(inode, offset, size);
+
+ if (ret < 0) {
+ printk(KERN_EMERG "%s: failed to convert unwritten"
+ "extents to written extents, error is %d"
+ " io is still on inode %lu aio dio list\n",
+ __func__, ret, inode->i_ino);
+ return ret;
+ }
+
+ /* clear the DIO AIO unwritten flag */
+ io->flag = 0;
+ return ret;
+}
+/*
+ * work on completed aio dio IO, to convert unwritten extents to extents
+ */
+static void ext4_end_aio_dio_work(struct work_struct *work)
+{
+ ext4_io_end_t *io = container_of(work, ext4_io_end_t, work);
+ struct inode *inode = io->inode;
+ int ret = 0;
+
+ mutex_lock(&inode->i_mutex);
+ ret = ext4_end_aio_dio_nolock(io);
+ if (ret >= 0) {
+ if (!list_empty(&io->list))
+ list_del_init(&io->list);
+ ext4_free_io_end(io);
+ }
+ mutex_unlock(&inode->i_mutex);
+}
+/*
+ * This function is called from ext4_sync_file().
+ *
+ * When AIO DIO IO is completed, the work to convert unwritten
+ * extents to written is queued on workqueue but may not get immediately
+ * scheduled. When fsync is called, we need to ensure the
+ * conversion is complete before fsync returns.
+ * The inode keeps track of a list of completed AIO from DIO path
+ * that might needs to do the conversion. This function walks through
+ * the list and convert the related unwritten extents to written.
+ */
+int flush_aio_dio_completed_IO(struct inode *inode)
+{
+ ext4_io_end_t *io;
+ int ret = 0;
+ int ret2 = 0;
+
+ if (list_empty(&EXT4_I(inode)->i_aio_dio_complete_list))
+ return ret;
+
+ dump_aio_dio_list(inode);
+ while (!list_empty(&EXT4_I(inode)->i_aio_dio_complete_list)){
+ io = list_entry(EXT4_I(inode)->i_aio_dio_complete_list.next,
+ ext4_io_end_t, list);
+ /*
+ * Calling ext4_end_aio_dio_nolock() to convert completed
+ * IO to written.
+ *
+ * When ext4_sync_file() is called, run_queue() may already
+ * about to flush the work corresponding to this io structure.
+ * It will be upset if it founds the io structure related
+ * to the work-to-be schedule is freed.
+ *
+ * Thus we need to keep the io structure still valid here after
+ * convertion finished. The io structure has a flag to
+ * avoid double converting from both fsync and background work
+ * queue work.
+ */
+ ret = ext4_end_aio_dio_nolock(io);
+ if (ret < 0)
+ ret2 = ret;
+ else
+ list_del_init(&io->list);
+ }
+ return (ret2 < 0) ? ret2 : 0;
+}
+
+static ext4_io_end_t *ext4_init_io_end (struct inode *inode)
+{
+ ext4_io_end_t *io = NULL;
+
+ io = kmalloc(sizeof(*io), GFP_NOFS);
+
+ if (io) {
+ igrab(inode);
+ io->inode = inode;
+ io->flag = 0;
+ io->offset = 0;
+ io->size = 0;
+ io->error = 0;
+ INIT_WORK(&io->work, ext4_end_aio_dio_work);
+ INIT_LIST_HEAD(&io->list);
+ }
+
+ return io;
+}
+
+static void ext4_end_io_dio(struct kiocb *iocb, loff_t offset,
+ ssize_t size, void *private)
+{
+ ext4_io_end_t *io_end = iocb->private;
+ struct workqueue_struct *wq;
+
+ ext_debug("ext4_end_io_dio(): io_end 0x%p"
+ "for inode %lu, iocb 0x%p, offset %llu, size %llu\n",
+ iocb->private, io_end->inode->i_ino, iocb, offset,
+ size);
+ /* if not async direct IO or dio with 0 bytes write, just return */
+ if (!io_end || !size)
+ return;
+
+ /* if not aio dio with unwritten extents, just free io and return */
+ if (io_end->flag != DIO_AIO_UNWRITTEN){
+ ext4_free_io_end(io_end);
+ iocb->private = NULL;
+ return;
+ }
+
+ io_end->offset = offset;
+ io_end->size = size;
+ wq = EXT4_SB(io_end->inode->i_sb)->dio_unwritten_wq;
+
+ /* queue the work to convert unwritten extents to written */
+ queue_work(wq, &io_end->work);
+
+ /* Add the io_end to per-inode completed aio dio list*/
+ list_add_tail(&io_end->list,
+ &EXT4_I(io_end->inode)->i_aio_dio_complete_list);
+ iocb->private = NULL;
+}
+/*
+ * For ext4 extent files, ext4 will do direct-io write to holes,
+ * preallocated extents, and those write extend the file, no need to
+ * fall back to buffered IO.
+ *
+ * For holes, we fallocate those blocks, mark them as unintialized
+ * If those blocks were preallocated, we mark sure they are splited, but
+ * still keep the range to write as unintialized.
+ *
+ * The unwrritten extents will be converted to written when DIO is completed.
+ * For async direct IO, since the IO may still pending when return, we
+ * set up an end_io call back function, which will do the convertion
+ * when async direct IO completed.
+ *
+ * If the O_DIRECT write will extend the file then add this inode to the
+ * orphan list. So recovery will truncate it back to the original size
+ * if the machine crashes during the write.
+ *
+ */
+static ssize_t ext4_ext_direct_IO(int rw, struct kiocb *iocb,
+ const struct iovec *iov, loff_t offset,
+ unsigned long nr_segs)
+{
+ struct file *file = iocb->ki_filp;
+ struct inode *inode = file->f_mapping->host;
+ ssize_t ret;
+ size_t count = iov_length(iov, nr_segs);
+
+ loff_t final_size = offset + count;
+ if (rw == WRITE && final_size <= inode->i_size) {
+ /*
+ * We could direct write to holes and fallocate.
+ *
+ * Allocated blocks to fill the hole are marked as uninitialized
+ * to prevent paralel buffered read to expose the stale data
+ * before DIO complete the data IO.
+ *
+ * As to previously fallocated extents, ext4 get_block
+ * will just simply mark the buffer mapped but still
+ * keep the extents uninitialized.
+ *
+ * for non AIO case, we will convert those unwritten extents
+ * to written after return back from blockdev_direct_IO.
+ *
+ * for async DIO, the conversion needs to be defered when
+ * the IO is completed. The ext4 end_io callback function
+ * will be called to take care of the conversion work.
+ * Here for async case, we allocate an io_end structure to
+ * hook to the iocb.
+ */
+ iocb->private = NULL;
+ EXT4_I(inode)->cur_aio_dio = NULL;
+ if (!is_sync_kiocb(iocb)) {
+ iocb->private = ext4_init_io_end(inode);
+ if (!iocb->private)
+ return -ENOMEM;
+ /*
+ * we save the io structure for current async
+ * direct IO, so that later ext4_get_blocks()
+ * could flag the io structure whether there
+ * is a unwritten extents needs to be converted
+ * when IO is completed.
+ */
+ EXT4_I(inode)->cur_aio_dio = iocb->private;
+ }
+
+ ret = blockdev_direct_IO(rw, iocb, inode,
+ inode->i_sb->s_bdev, iov,
+ offset, nr_segs,
+ ext4_get_block_dio_write,
+ ext4_end_io_dio);
+ if (iocb->private)
+ EXT4_I(inode)->cur_aio_dio = NULL;
+ /*
+ * The io_end structure takes a reference to the inode,
+ * that structure needs to be destroyed and the
+ * reference to the inode need to be dropped, when IO is
+ * complete, even with 0 byte write, or failed.
+ *
+ * In the successful AIO DIO case, the io_end structure will be
+ * desctroyed and the reference to the inode will be dropped
+ * after the end_io call back function is called.
+ *
+ * In the case there is 0 byte write, or error case, since
+ * VFS direct IO won't invoke the end_io call back function,
+ * we need to free the end_io structure here.
+ */
+ if (ret != -EIOCBQUEUED && ret <= 0 && iocb->private) {
+ ext4_free_io_end(iocb->private);
+ iocb->private = NULL;
+ } else if (ret > 0)
+ /*
+ * for non AIO case, since the IO is already
+ * completed, we could do the convertion right here
+ */
+ ret = ext4_convert_unwritten_extents(inode,
+ offset, ret);
+ return ret;
+ }
+
+ /* for write the the end of file case, we fall back to old way */
+ return ext4_ind_direct_IO(rw, iocb, iov, offset, nr_segs);
+}
+
+static ssize_t ext4_direct_IO(int rw, struct kiocb *iocb,
+ const struct iovec *iov, loff_t offset,
+ unsigned long nr_segs)
+{
+ struct file *file = iocb->ki_filp;
+ struct inode *inode = file->f_mapping->host;
+
+ if (EXT4_I(inode)->i_flags & EXT4_EXTENTS_FL)
+ return ext4_ext_direct_IO(rw, iocb, iov, offset, nr_segs);
+
+ return ext4_ind_direct_IO(rw, iocb, iov, offset, nr_segs);
+}
+
/*
* Pages can be marked dirty completely asynchronously from ext4's journalling
* activity. By filemap_sync_pte(), try_to_unmap_one(), etc. We cannot do
.direct_IO = ext4_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations ext4_writeback_aops = {
.direct_IO = ext4_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations ext4_journalled_aops = {
.invalidatepage = ext4_invalidatepage,
.releasepage = ext4_releasepage,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations ext4_da_aops = {
.direct_IO = ext4_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
void ext4_set_aops(struct inode *inode)
*/
static int ext4_do_update_inode(handle_t *handle,
struct inode *inode,
- struct ext4_iloc *iloc,
- int do_sync)
+ struct ext4_iloc *iloc)
{
struct ext4_inode *raw_inode = ext4_raw_inode(iloc);
struct ext4_inode_info *ei = EXT4_I(inode);
raw_inode->i_extra_isize = cpu_to_le16(ei->i_extra_isize);
}
- /*
- * If we're not using a journal and we were called from
- * ext4_write_inode() to sync the inode (making do_sync true),
- * we can just use sync_dirty_buffer() directly to do our dirty
- * work. Testing s_journal here is a bit redundant but it's
- * worth it to avoid potential future trouble.
- */
- if (EXT4_SB(inode->i_sb)->s_journal == NULL && do_sync) {
- BUFFER_TRACE(bh, "call sync_dirty_buffer");
- sync_dirty_buffer(bh);
- } else {
- BUFFER_TRACE(bh, "call ext4_handle_dirty_metadata");
- rc = ext4_handle_dirty_metadata(handle, inode, bh);
- if (!err)
- err = rc;
- }
+ BUFFER_TRACE(bh, "call ext4_handle_dirty_metadata");
+ rc = ext4_handle_dirty_metadata(handle, inode, bh);
+ if (!err)
+ err = rc;
ei->i_state &= ~EXT4_STATE_NEW;
out_brelse:
err = ext4_get_inode_loc(inode, &iloc);
if (err)
return err;
- err = ext4_do_update_inode(EXT4_NOJOURNAL_HANDLE,
- inode, &iloc, wait);
+ if (wait)
+ sync_dirty_buffer(iloc.bh);
+ if (buffer_req(iloc.bh) && !buffer_uptodate(iloc.bh)) {
+ ext4_error(inode->i_sb, __func__,
+ "IO error syncing inode, "
+ "inode=%lu, block=%llu",
+ inode->i_ino,
+ (unsigned long long)iloc.bh->b_blocknr);
+ err = -EIO;
+ }
}
return err;
}
get_bh(iloc->bh);
/* ext4_do_update_inode() does jbd2_journal_dirty_metadata */
- err = ext4_do_update_inode(handle, inode, iloc, 0);
+ err = ext4_do_update_inode(handle, inode, iloc);
put_bh(iloc->bh);
return err;
}
*/
void ext4_dirty_inode(struct inode *inode)
{
- handle_t *current_handle = ext4_journal_current_handle();
handle_t *handle;
- if (!ext4_handle_valid(current_handle)) {
- ext4_mark_inode_dirty(current_handle, inode);
- return;
- }
-
handle = ext4_journal_start(inode, 2);
if (IS_ERR(handle))
goto out;
- if (current_handle &&
- current_handle->h_transaction != handle->h_transaction) {
- /* This task has a transaction open against a different fs */
- printk(KERN_EMERG "%s: transactions do not match!\n",
- __func__);
- } else {
- jbd_debug(5, "marking dirty. outer handle=%p\n",
- current_handle);
- ext4_mark_inode_dirty(handle, inode);
- }
+
+ ext4_mark_inode_dirty(handle, inode);
+
ext4_journal_stop(handle);
out:
return;
return err;
}
-#ifdef EXT4_MB_HISTORY
-struct ext4_mb_proc_session {
- struct ext4_mb_history *history;
- struct super_block *sb;
- int start;
- int max;
-};
-
-static void *ext4_mb_history_skip_empty(struct ext4_mb_proc_session *s,
- struct ext4_mb_history *hs,
- int first)
-{
- if (hs == s->history + s->max)
- hs = s->history;
- if (!first && hs == s->history + s->start)
- return NULL;
- while (hs->orig.fe_len == 0) {
- hs++;
- if (hs == s->history + s->max)
- hs = s->history;
- if (hs == s->history + s->start)
- return NULL;
- }
- return hs;
-}
-
-static void *ext4_mb_seq_history_start(struct seq_file *seq, loff_t *pos)
-{
- struct ext4_mb_proc_session *s = seq->private;
- struct ext4_mb_history *hs;
- int l = *pos;
-
- if (l == 0)
- return SEQ_START_TOKEN;
- hs = ext4_mb_history_skip_empty(s, s->history + s->start, 1);
- if (!hs)
- return NULL;
- while (--l && (hs = ext4_mb_history_skip_empty(s, ++hs, 0)) != NULL);
- return hs;
-}
-
-static void *ext4_mb_seq_history_next(struct seq_file *seq, void *v,
- loff_t *pos)
-{
- struct ext4_mb_proc_session *s = seq->private;
- struct ext4_mb_history *hs = v;
-
- ++*pos;
- if (v == SEQ_START_TOKEN)
- return ext4_mb_history_skip_empty(s, s->history + s->start, 1);
- else
- return ext4_mb_history_skip_empty(s, ++hs, 0);
-}
-
-static int ext4_mb_seq_history_show(struct seq_file *seq, void *v)
-{
- char buf[25], buf2[25], buf3[25], *fmt;
- struct ext4_mb_history *hs = v;
-
- if (v == SEQ_START_TOKEN) {
- seq_printf(seq, "%-5s %-8s %-23s %-23s %-23s %-5s "
- "%-5s %-2s %-6s %-5s %-5s %-6s\n",
- "pid", "inode", "original", "goal", "result", "found",
- "grps", "cr", "flags", "merge", "tail", "broken");
- return 0;
- }
-
- if (hs->op == EXT4_MB_HISTORY_ALLOC) {
- fmt = "%-5u %-8u %-23s %-23s %-23s %-5u %-5u %-2u "
- "0x%04x %-5s %-5u %-6u\n";
- sprintf(buf2, "%u/%d/%u@%u", hs->result.fe_group,
- hs->result.fe_start, hs->result.fe_len,
- hs->result.fe_logical);
- sprintf(buf, "%u/%d/%u@%u", hs->orig.fe_group,
- hs->orig.fe_start, hs->orig.fe_len,
- hs->orig.fe_logical);
- sprintf(buf3, "%u/%d/%u@%u", hs->goal.fe_group,
- hs->goal.fe_start, hs->goal.fe_len,
- hs->goal.fe_logical);
- seq_printf(seq, fmt, hs->pid, hs->ino, buf, buf3, buf2,
- hs->found, hs->groups, hs->cr, hs->flags,
- hs->merged ? "M" : "", hs->tail,
- hs->buddy ? 1 << hs->buddy : 0);
- } else if (hs->op == EXT4_MB_HISTORY_PREALLOC) {
- fmt = "%-5u %-8u %-23s %-23s %-23s\n";
- sprintf(buf2, "%u/%d/%u@%u", hs->result.fe_group,
- hs->result.fe_start, hs->result.fe_len,
- hs->result.fe_logical);
- sprintf(buf, "%u/%d/%u@%u", hs->orig.fe_group,
- hs->orig.fe_start, hs->orig.fe_len,
- hs->orig.fe_logical);
- seq_printf(seq, fmt, hs->pid, hs->ino, buf, "", buf2);
- } else if (hs->op == EXT4_MB_HISTORY_DISCARD) {
- sprintf(buf2, "%u/%d/%u", hs->result.fe_group,
- hs->result.fe_start, hs->result.fe_len);
- seq_printf(seq, "%-5u %-8u %-23s discard\n",
- hs->pid, hs->ino, buf2);
- } else if (hs->op == EXT4_MB_HISTORY_FREE) {
- sprintf(buf2, "%u/%d/%u", hs->result.fe_group,
- hs->result.fe_start, hs->result.fe_len);
- seq_printf(seq, "%-5u %-8u %-23s free\n",
- hs->pid, hs->ino, buf2);
- }
- return 0;
-}
-
-static void ext4_mb_seq_history_stop(struct seq_file *seq, void *v)
-{
-}
-
-static const struct seq_operations ext4_mb_seq_history_ops = {
- .start = ext4_mb_seq_history_start,
- .next = ext4_mb_seq_history_next,
- .stop = ext4_mb_seq_history_stop,
- .show = ext4_mb_seq_history_show,
-};
-
-static int ext4_mb_seq_history_open(struct inode *inode, struct file *file)
-{
- struct super_block *sb = PDE(inode)->data;
- struct ext4_sb_info *sbi = EXT4_SB(sb);
- struct ext4_mb_proc_session *s;
- int rc;
- int size;
-
- if (unlikely(sbi->s_mb_history == NULL))
- return -ENOMEM;
- s = kmalloc(sizeof(*s), GFP_KERNEL);
- if (s == NULL)
- return -ENOMEM;
- s->sb = sb;
- size = sizeof(struct ext4_mb_history) * sbi->s_mb_history_max;
- s->history = kmalloc(size, GFP_KERNEL);
- if (s->history == NULL) {
- kfree(s);
- return -ENOMEM;
- }
-
- spin_lock(&sbi->s_mb_history_lock);
- memcpy(s->history, sbi->s_mb_history, size);
- s->max = sbi->s_mb_history_max;
- s->start = sbi->s_mb_history_cur % s->max;
- spin_unlock(&sbi->s_mb_history_lock);
-
- rc = seq_open(file, &ext4_mb_seq_history_ops);
- if (rc == 0) {
- struct seq_file *m = (struct seq_file *)file->private_data;
- m->private = s;
- } else {
- kfree(s->history);
- kfree(s);
- }
- return rc;
-
-}
-
-static int ext4_mb_seq_history_release(struct inode *inode, struct file *file)
-{
- struct seq_file *seq = (struct seq_file *)file->private_data;
- struct ext4_mb_proc_session *s = seq->private;
- kfree(s->history);
- kfree(s);
- return seq_release(inode, file);
-}
-
-static ssize_t ext4_mb_seq_history_write(struct file *file,
- const char __user *buffer,
- size_t count, loff_t *ppos)
-{
- struct seq_file *seq = (struct seq_file *)file->private_data;
- struct ext4_mb_proc_session *s = seq->private;
- struct super_block *sb = s->sb;
- char str[32];
- int value;
-
- if (count >= sizeof(str)) {
- printk(KERN_ERR "EXT4-fs: %s string too long, max %u bytes\n",
- "mb_history", (int)sizeof(str));
- return -EOVERFLOW;
- }
-
- if (copy_from_user(str, buffer, count))
- return -EFAULT;
-
- value = simple_strtol(str, NULL, 0);
- if (value < 0)
- return -ERANGE;
- EXT4_SB(sb)->s_mb_history_filter = value;
-
- return count;
-}
-
-static const struct file_operations ext4_mb_seq_history_fops = {
- .owner = THIS_MODULE,
- .open = ext4_mb_seq_history_open,
- .read = seq_read,
- .write = ext4_mb_seq_history_write,
- .llseek = seq_lseek,
- .release = ext4_mb_seq_history_release,
-};
-
static void *ext4_mb_seq_groups_start(struct seq_file *seq, loff_t *pos)
{
struct super_block *sb = seq->private;
.release = seq_release,
};
-static void ext4_mb_history_release(struct super_block *sb)
-{
- struct ext4_sb_info *sbi = EXT4_SB(sb);
-
- if (sbi->s_proc != NULL) {
- remove_proc_entry("mb_groups", sbi->s_proc);
- if (sbi->s_mb_history_max)
- remove_proc_entry("mb_history", sbi->s_proc);
- }
- kfree(sbi->s_mb_history);
-}
-
-static void ext4_mb_history_init(struct super_block *sb)
-{
- struct ext4_sb_info *sbi = EXT4_SB(sb);
- int i;
-
- if (sbi->s_proc != NULL) {
- if (sbi->s_mb_history_max)
- proc_create_data("mb_history", S_IRUGO, sbi->s_proc,
- &ext4_mb_seq_history_fops, sb);
- proc_create_data("mb_groups", S_IRUGO, sbi->s_proc,
- &ext4_mb_seq_groups_fops, sb);
- }
-
- sbi->s_mb_history_cur = 0;
- spin_lock_init(&sbi->s_mb_history_lock);
- i = sbi->s_mb_history_max * sizeof(struct ext4_mb_history);
- sbi->s_mb_history = i ? kzalloc(i, GFP_KERNEL) : NULL;
- /* if we can't allocate history, then we simple won't use it */
-}
-
-static noinline_for_stack void
-ext4_mb_store_history(struct ext4_allocation_context *ac)
-{
- struct ext4_sb_info *sbi = EXT4_SB(ac->ac_sb);
- struct ext4_mb_history h;
-
- if (sbi->s_mb_history == NULL)
- return;
-
- if (!(ac->ac_op & sbi->s_mb_history_filter))
- return;
-
- h.op = ac->ac_op;
- h.pid = current->pid;
- h.ino = ac->ac_inode ? ac->ac_inode->i_ino : 0;
- h.orig = ac->ac_o_ex;
- h.result = ac->ac_b_ex;
- h.flags = ac->ac_flags;
- h.found = ac->ac_found;
- h.groups = ac->ac_groups_scanned;
- h.cr = ac->ac_criteria;
- h.tail = ac->ac_tail;
- h.buddy = ac->ac_buddy;
- h.merged = 0;
- if (ac->ac_op == EXT4_MB_HISTORY_ALLOC) {
- if (ac->ac_g_ex.fe_start == ac->ac_b_ex.fe_start &&
- ac->ac_g_ex.fe_group == ac->ac_b_ex.fe_group)
- h.merged = 1;
- h.goal = ac->ac_g_ex;
- h.result = ac->ac_f_ex;
- }
-
- spin_lock(&sbi->s_mb_history_lock);
- memcpy(sbi->s_mb_history + sbi->s_mb_history_cur, &h, sizeof(h));
- if (++sbi->s_mb_history_cur >= sbi->s_mb_history_max)
- sbi->s_mb_history_cur = 0;
- spin_unlock(&sbi->s_mb_history_lock);
-}
-
-#else
-#define ext4_mb_history_release(sb)
-#define ext4_mb_history_init(sb)
-#endif
-
/* Create and initialize ext4_group_info data for the given group. */
int ext4_mb_add_groupinfo(struct super_block *sb, ext4_group_t group,
sbi->s_mb_stats = MB_DEFAULT_STATS;
sbi->s_mb_stream_request = MB_DEFAULT_STREAM_THRESHOLD;
sbi->s_mb_order2_reqs = MB_DEFAULT_ORDER2_REQS;
- sbi->s_mb_history_filter = EXT4_MB_HISTORY_DEFAULT;
sbi->s_mb_group_prealloc = MB_DEFAULT_GROUP_PREALLOC;
sbi->s_locality_groups = alloc_percpu(struct ext4_locality_group);
spin_lock_init(&lg->lg_prealloc_lock);
}
- ext4_mb_history_init(sb);
+ if (sbi->s_proc)
+ proc_create_data("mb_groups", S_IRUGO, sbi->s_proc,
+ &ext4_mb_seq_groups_fops, sb);
if (sbi->s_journal)
sbi->s_journal->j_commit_callback = release_blocks_on_commit;
-
- printk(KERN_INFO "EXT4-fs: mballoc enabled\n");
return 0;
}
}
free_percpu(sbi->s_locality_groups);
- ext4_mb_history_release(sb);
+ if (sbi->s_proc)
+ remove_proc_entry("mb_groups", sbi->s_proc);
return 0;
}
atomic_inc(&sbi->s_bal_breaks);
}
- ext4_mb_store_history(ac);
+ if (ac->ac_op == EXT4_MB_HISTORY_ALLOC)
+ trace_ext4_mballoc_alloc(ac);
+ else
+ trace_ext4_mballoc_prealloc(ac);
}
/*
if (ac) {
ac->ac_sb = sb;
ac->ac_inode = pa->pa_inode;
- ac->ac_op = EXT4_MB_HISTORY_DISCARD;
}
while (bit < end) {
ac->ac_b_ex.fe_start = bit;
ac->ac_b_ex.fe_len = next - bit;
ac->ac_b_ex.fe_logical = 0;
- ext4_mb_store_history(ac);
+ trace_ext4_mballoc_discard(ac);
}
trace_ext4_mb_release_inode_pa(ac, pa, grp_blk_start + bit,
ext4_group_t group;
ext4_grpblk_t bit;
- if (ac)
- ac->ac_op = EXT4_MB_HISTORY_DISCARD;
-
trace_ext4_mb_release_group_pa(ac, pa);
BUG_ON(pa->pa_deleted == 0);
ext4_get_group_no_and_offset(sb, pa->pa_pstart, &group, &bit);
ac->ac_b_ex.fe_start = bit;
ac->ac_b_ex.fe_len = pa->pa_len;
ac->ac_b_ex.fe_logical = 0;
- ext4_mb_store_history(ac);
+ trace_ext4_mballoc_discard(ac);
}
return 0;
size = ac->ac_o_ex.fe_logical + ac->ac_o_ex.fe_len;
isize = (i_size_read(ac->ac_inode) + ac->ac_sb->s_blocksize - 1)
>> bsbits;
- size = max(size, isize);
if ((size == isize) &&
!ext4_fs_is_busy(sbi) &&
}
/* don't use group allocation for large files */
+ size = max(size, isize);
if (size >= sbi->s_mb_stream_request) {
ac->ac_flags |= EXT4_MB_STREAM_ALLOC;
return;
ac = kmem_cache_alloc(ext4_ac_cachep, GFP_NOFS);
if (ac) {
- ac->ac_op = EXT4_MB_HISTORY_FREE;
ac->ac_inode = inode;
ac->ac_sb = sb;
}
ac->ac_b_ex.fe_group = block_group;
ac->ac_b_ex.fe_start = bit;
ac->ac_b_ex.fe_len = count;
- ext4_mb_store_history(ac);
+ trace_ext4_mballoc_free(ac);
}
err = ext4_mb_load_buddy(sb, block_group, &e4b);
#define mb_debug(n, fmt, a...)
#endif
-/*
- * with EXT4_MB_HISTORY mballoc stores last N allocations in memory
- * and you can monitor it in /proc/fs/ext4/<dev>/mb_history
- */
-#define EXT4_MB_HISTORY
#define EXT4_MB_HISTORY_ALLOC 1 /* allocation */
#define EXT4_MB_HISTORY_PREALLOC 2 /* preallocated blocks used */
-#define EXT4_MB_HISTORY_DISCARD 4 /* preallocation discarded */
-#define EXT4_MB_HISTORY_FREE 8 /* free */
-
-#define EXT4_MB_HISTORY_DEFAULT (EXT4_MB_HISTORY_ALLOC | \
- EXT4_MB_HISTORY_PREALLOC)
/*
* How long mballoc can look for a best extent (in found extents)
* with 'ext4_mb_stats' allocator will collect stats that will be
* shown at umount. The collecting costs though!
*/
-#define MB_DEFAULT_STATS 1
+#define MB_DEFAULT_STATS 0
/*
* files smaller than MB_DEFAULT_STREAM_THRESHOLD are served
#define AC_STATUS_FOUND 2
#define AC_STATUS_BREAK 3
-struct ext4_mb_history {
- struct ext4_free_extent orig; /* orig allocation */
- struct ext4_free_extent goal; /* goal allocation */
- struct ext4_free_extent result; /* result allocation */
- unsigned pid;
- unsigned ino;
- __u16 found; /* how many extents have been found */
- __u16 groups; /* how many groups have been scanned */
- __u16 tail; /* what tail broke some buddy */
- __u16 buddy; /* buddy the tail ^^^ broke */
- __u16 flags;
- __u8 cr:3; /* which phase the result extent was found at */
- __u8 op:4;
- __u8 merged:1;
-};
-
struct ext4_buddy {
struct page *bd_buddy_page;
void *bd_buddy;
#define EXT4_MB_BITMAP(e4b) ((e4b)->bd_bitmap)
#define EXT4_MB_BUDDY(e4b) ((e4b)->bd_buddy)
-#ifndef EXT4_MB_HISTORY
-static inline void ext4_mb_store_history(struct ext4_allocation_context *ac)
-{
- return;
-}
-#endif
-
#define in_range(b, first, len) ((b) >= (first) && (b) <= (first) + (len) - 1)
static inline ext4_fsblk_t ext4_grp_offs_to_block(struct super_block *sb,
goto err_out;
}
}
- retval = ext4_ext_insert_extent(handle, inode, path, &newext);
+ retval = ext4_ext_insert_extent(handle, inode, path, &newext, 0);
err_out:
if (path) {
ext4_ext_drop_refs(path);
goto out;
if (ext4_ext_insert_extent(handle, orig_inode,
- orig_path, new_ext))
+ orig_path, new_ext, 0))
goto out;
}
goto out;
if (ext4_ext_insert_extent(handle, orig_inode,
- orig_path, end_ext))
+ orig_path, end_ext, 0))
goto out;
}
out:
return -EINVAL;
}
- /* orig and donor should be different file */
- if (orig_inode->i_ino == donor_inode->i_ino) {
- ext4_debug("ext4 move extent: The argument files should not "
- "be same file [ino:orig %lu, donor %lu]\n",
- orig_inode->i_ino, donor_inode->i_ino);
- return -EINVAL;
- }
-
/* Ext4 move extent supports only extent based file */
if (!(EXT4_I(orig_inode)->i_flags & EXT4_EXTENTS_FL)) {
ext4_debug("ext4 move extent: orig file is not extents "
int block_len_in_page;
int uninit;
+ /* orig and donor should be different file */
+ if (orig_inode->i_ino == donor_inode->i_ino) {
+ ext4_debug("ext4 move extent: The argument files should not "
+ "be same file [ino:orig %lu, donor %lu]\n",
+ orig_inode->i_ino, donor_inode->i_ino);
+ return -EINVAL;
+ }
+
/* protect orig and donor against a truncate */
ret1 = mext_inode_double_lock(orig_inode, donor_inode);
if (ret1 < 0)
struct ext4_iloc iloc;
int err = 0;
- if (!ext4_handle_valid(handle))
+ /* ext4_handle_valid() assumes a valid handle_t pointer */
+ if (handle && !ext4_handle_valid(handle))
return 0;
mutex_lock(&EXT4_SB(inode->i_sb)->s_orphan_lock);
#define CREATE_TRACE_POINTS
#include <trace/events/ext4.h>
-static int default_mb_history_length = 1000;
-
-module_param_named(default_mb_history_length, default_mb_history_length,
- int, 0644);
-MODULE_PARM_DESC(default_mb_history_length,
- "Default number of entries saved for mb_history");
-
struct proc_dir_entry *ext4_proc_root;
static struct kset *ext4_kset;
bg->bg_itable_unused_hi = cpu_to_le16(count >> 16);
}
+
+/* Just increment the non-pointer handle value */
+static handle_t *ext4_get_nojournal(void)
+{
+ handle_t *handle = current->journal_info;
+ unsigned long ref_cnt = (unsigned long)handle;
+
+ BUG_ON(ref_cnt >= EXT4_NOJOURNAL_MAX_REF_COUNT);
+
+ ref_cnt++;
+ handle = (handle_t *)ref_cnt;
+
+ current->journal_info = handle;
+ return handle;
+}
+
+
+/* Decrement the non-pointer handle value */
+static void ext4_put_nojournal(handle_t *handle)
+{
+ unsigned long ref_cnt = (unsigned long)handle;
+
+ BUG_ON(ref_cnt == 0);
+
+ ref_cnt--;
+ handle = (handle_t *)ref_cnt;
+
+ current->journal_info = handle;
+}
+
/*
* Wrappers for jbd2_journal_start/end.
*
}
return jbd2_journal_start(journal, nblocks);
}
- /*
- * We're not journaling, return the appropriate indication.
- */
- current->journal_info = EXT4_NOJOURNAL_HANDLE;
- return current->journal_info;
+ return ext4_get_nojournal();
}
/*
int rc;
if (!ext4_handle_valid(handle)) {
- /*
- * Do this here since we don't call jbd2_journal_stop() in
- * no-journal mode.
- */
- current->journal_info = NULL;
+ ext4_put_nojournal(handle);
return 0;
}
sb = handle->h_transaction->t_journal->j_private;
struct ext4_super_block *es = sbi->s_es;
int i, err;
+ flush_workqueue(sbi->dio_unwritten_wq);
+ destroy_workqueue(sbi->dio_unwritten_wq);
+
lock_super(sb);
lock_kernel();
if (sb->s_dirt)
ei->i_allocated_meta_blocks = 0;
ei->i_delalloc_reserved_flag = 0;
spin_lock_init(&(ei->i_block_reservation_lock));
+ INIT_LIST_HEAD(&ei->i_aio_dio_complete_list);
+ ei->cur_aio_dio = NULL;
return &ei->vfs_inode;
}
Opt_journal_update, Opt_journal_dev,
Opt_journal_checksum, Opt_journal_async_commit,
Opt_abort, Opt_data_journal, Opt_data_ordered, Opt_data_writeback,
- Opt_data_err_abort, Opt_data_err_ignore, Opt_mb_history_length,
+ Opt_data_err_abort, Opt_data_err_ignore,
Opt_usrjquota, Opt_grpjquota, Opt_offusrjquota, Opt_offgrpjquota,
Opt_jqfmt_vfsold, Opt_jqfmt_vfsv0, Opt_quota, Opt_noquota,
Opt_ignore, Opt_barrier, Opt_nobarrier, Opt_err, Opt_resize,
{Opt_data_writeback, "data=writeback"},
{Opt_data_err_abort, "data_err=abort"},
{Opt_data_err_ignore, "data_err=ignore"},
- {Opt_mb_history_length, "mb_history_length=%u"},
{Opt_offusrjquota, "usrjquota="},
{Opt_usrjquota, "usrjquota=%s"},
{Opt_offgrpjquota, "grpjquota="},
case Opt_data_err_ignore:
clear_opt(sbi->s_mount_opt, DATA_ERR_ABORT);
break;
- case Opt_mb_history_length:
- if (match_int(&args[0], &option))
- return 0;
- if (option < 0)
- return 0;
- sbi->s_mb_history_max = option;
- break;
#ifdef CONFIG_QUOTA
case Opt_usrjquota:
qtype = USRQUOTA;
EXT4_INODES_PER_GROUP(sb),
sbi->s_mount_opt);
- if (EXT4_SB(sb)->s_journal) {
- ext4_msg(sb, KERN_INFO, "%s journal on %s",
- EXT4_SB(sb)->s_journal->j_inode ? "internal" :
- "external", EXT4_SB(sb)->s_journal->j_devname);
- } else {
- ext4_msg(sb, KERN_INFO, "no journal");
- }
return res;
}
EXT4_RW_ATTR_SBI_UI(mb_order2_req, s_mb_order2_reqs);
EXT4_RW_ATTR_SBI_UI(mb_stream_req, s_mb_stream_request);
EXT4_RW_ATTR_SBI_UI(mb_group_prealloc, s_mb_group_prealloc);
+EXT4_RW_ATTR_SBI_UI(max_writeback_mb_bump, s_max_writeback_mb_bump);
static struct attribute *ext4_attrs[] = {
ATTR_LIST(delayed_allocation_blocks),
ATTR_LIST(mb_order2_req),
ATTR_LIST(mb_stream_req),
ATTR_LIST(mb_group_prealloc),
+ ATTR_LIST(max_writeback_mb_bump),
NULL,
};
sbi->s_commit_interval = JBD2_DEFAULT_MAX_COMMIT_AGE * HZ;
sbi->s_min_batch_time = EXT4_DEF_MIN_BATCH_TIME;
sbi->s_max_batch_time = EXT4_DEF_MAX_BATCH_TIME;
- sbi->s_mb_history_max = default_mb_history_length;
set_opt(sbi->s_mount_opt, BARRIER);
}
sbi->s_stripe = ext4_get_stripe_size(sbi);
+ sbi->s_max_writeback_mb_bump = 128;
/*
* set up enough so that it can read an inode
clear_opt(sbi->s_mount_opt, NOBH);
}
}
+ EXT4_SB(sb)->dio_unwritten_wq = create_workqueue("ext4-dio-unwritten");
+ if (!EXT4_SB(sb)->dio_unwritten_wq) {
+ printk(KERN_ERR "EXT4-fs: failed to create DIO workqueue\n");
+ goto failed_mount_wq;
+ }
+
/*
* The jbd2_journal_load will have done any necessary log recovery,
* so we can safely mount the rest of the filesystem now.
"available");
}
- if (test_opt(sb, DATA_FLAGS) == EXT4_MOUNT_JOURNAL_DATA) {
+ if (test_opt(sb, DELALLOC) &&
+ (test_opt(sb, DATA_FLAGS) == EXT4_MOUNT_JOURNAL_DATA)) {
ext4_msg(sb, KERN_WARNING, "Ignoring delalloc option - "
"requested data journaling mode");
clear_opt(sbi->s_mount_opt, DELALLOC);
- } else if (test_opt(sb, DELALLOC))
- ext4_msg(sb, KERN_INFO, "delayed allocation enabled");
+ }
err = ext4_setup_system_zone(sb);
if (err) {
failed_mount4:
ext4_msg(sb, KERN_ERR, "mount failed");
+ destroy_workqueue(EXT4_SB(sb)->dio_unwritten_wq);
+failed_mount_wq:
ext4_release_system_zone(sb);
if (sbi->s_journal) {
jbd2_journal_destroy(sbi->s_journal);
return -EINVAL;
}
- if (journal->j_flags & JBD2_BARRIER)
- ext4_msg(sb, KERN_INFO, "barriers enabled");
- else
+ if (!(journal->j_flags & JBD2_BARRIER))
ext4_msg(sb, KERN_INFO, "barriers disabled");
if (!really_read_only && test_opt(sb, UPDATE_JOURNAL)) {
{
int ret = 0;
tid_t target;
+ struct ext4_sb_info *sbi = EXT4_SB(sb);
trace_ext4_sync_fs(sb, wait);
- if (jbd2_journal_start_commit(EXT4_SB(sb)->s_journal, &target)) {
+ flush_workqueue(sbi->dio_unwritten_wq);
+ if (jbd2_journal_start_commit(sbi->s_journal, &target)) {
if (wait)
- jbd2_log_wait_commit(EXT4_SB(sb)->s_journal, target);
+ jbd2_log_wait_commit(sbi->s_journal, target);
}
return ret;
}
.fs_flags = FS_REQUIRES_DEV,
};
-#ifdef CONFIG_EXT4DEV_COMPAT
-static int ext4dev_get_sb(struct file_system_type *fs_type, int flags,
- const char *dev_name, void *data,struct vfsmount *mnt)
-{
- printk(KERN_WARNING "EXT4-fs (%s): Update your userspace programs "
- "to mount using ext4\n", dev_name);
- printk(KERN_WARNING "EXT4-fs (%s): ext4dev backwards compatibility "
- "will go away by 2.6.31\n", dev_name);
- return get_sb_bdev(fs_type, flags, dev_name, data, ext4_fill_super,mnt);
-}
-
-static struct file_system_type ext4dev_fs_type = {
- .owner = THIS_MODULE,
- .name = "ext4dev",
- .get_sb = ext4dev_get_sb,
- .kill_sb = kill_block_super,
- .fs_flags = FS_REQUIRES_DEV,
-};
-MODULE_ALIAS("ext4dev");
-#endif
-
static int __init init_ext4_fs(void)
{
int err;
err = register_filesystem(&ext4_fs_type);
if (err)
goto out;
-#ifdef CONFIG_EXT4DEV_COMPAT
- err = register_filesystem(&ext4dev_fs_type);
- if (err) {
- unregister_filesystem(&ext4_fs_type);
- goto out;
- }
-#endif
return 0;
out:
destroy_inodecache();
static void __exit exit_ext4_fs(void)
{
unregister_filesystem(&ext4_fs_type);
-#ifdef CONFIG_EXT4DEV_COMPAT
- unregister_filesystem(&ext4dev_fs_type);
-#endif
destroy_inodecache();
exit_ext4_xattr();
exit_ext4_mballoc();
/* fat/misc.c */
extern void fat_fs_error(struct super_block *s, const char *fmt, ...)
__attribute__ ((format (printf, 2, 3))) __cold;
-extern void fat_clusters_flush(struct super_block *sb);
+extern int fat_clusters_flush(struct super_block *sb);
extern int fat_chain_add(struct inode *inode, int new_dclus, int nr_cluster);
extern void fat_time_fat2unix(struct msdos_sb_info *sbi, struct timespec *ts,
__le16 __time, __le16 __date, u8 time_cs);
static int fat_sync_fs(struct super_block *sb, int wait)
{
- lock_super(sb);
- fat_clusters_flush(sb);
- sb->s_dirt = 0;
- unlock_super(sb);
+ int err = 0;
- return 0;
+ if (sb->s_dirt) {
+ lock_super(sb);
+ sb->s_dirt = 0;
+ err = fat_clusters_flush(sb);
+ unlock_super(sb);
+ }
+
+ return err;
}
static void fat_put_super(struct super_block *sb)
iput(sbi->fat_inode);
- if (sbi->nls_disk) {
- unload_nls(sbi->nls_disk);
- sbi->nls_disk = NULL;
- sbi->options.codepage = fat_default_codepage;
- }
- if (sbi->nls_io) {
- unload_nls(sbi->nls_io);
- sbi->nls_io = NULL;
- }
- if (sbi->options.iocharset != fat_default_iocharset) {
+ unload_nls(sbi->nls_disk);
+ unload_nls(sbi->nls_io);
+
+ if (sbi->options.iocharset != fat_default_iocharset)
kfree(sbi->options.iocharset);
- sbi->options.iocharset = fat_default_iocharset;
- }
sb->s_fs_info = NULL;
kfree(sbi);
seq_puts(m, ",shortname=mixed");
break;
case VFAT_SFN_DISPLAY_LOWER | VFAT_SFN_CREATE_WIN95:
- /* seq_puts(m, ",shortname=lower"); */
+ seq_puts(m, ",shortname=lower");
break;
default:
seq_puts(m, ",shortname=unknown");
opts->codepage = fat_default_codepage;
opts->iocharset = fat_default_iocharset;
if (is_vfat) {
- opts->shortname = VFAT_SFN_DISPLAY_LOWER|VFAT_SFN_CREATE_WIN95;
+ opts->shortname = VFAT_SFN_DISPLAY_WINNT|VFAT_SFN_CREATE_WIN95;
opts->rodir = 0;
} else {
opts->shortname = 0;
/* Flushes the number of free clusters on FAT32 */
/* XXX: Need to write one per FSINFO block. Currently only writes 1 */
-void fat_clusters_flush(struct super_block *sb)
+int fat_clusters_flush(struct super_block *sb)
{
struct msdos_sb_info *sbi = MSDOS_SB(sb);
struct buffer_head *bh;
struct fat_boot_fsinfo *fsinfo;
if (sbi->fat_bits != 32)
- return;
+ return 0;
bh = sb_bread(sb, sbi->fsinfo_sector);
if (bh == NULL) {
printk(KERN_ERR "FAT: bread failed in fat_clusters_flush\n");
- return;
+ return -EIO;
}
fsinfo = (struct fat_boot_fsinfo *)bh->b_data;
mark_buffer_dirty(bh);
}
brelse(bh);
+
+ return 0;
}
/*
int charlen;
if (utf8) {
- int name_len = strlen(name);
-
- *outlen = utf8s_to_utf16s(name, PATH_MAX, (wchar_t *) outname);
-
- /*
- * We stripped '.'s before and set len appropriately,
- * but utf8s_to_utf16s doesn't care about len
- */
- *outlen -= (name_len - len);
-
- if (*outlen > 255)
+ *outlen = utf8s_to_utf16s(name, len, (wchar_t *)outname);
+ if (*outlen < 0)
+ return *outlen;
+ else if (*outlen > 255)
return -ENAMETOOLONG;
op = &outname[*outlen * sizeof(wchar_t)];
return pid;
}
+static int f_setown_ex(struct file *filp, unsigned long arg)
+{
+ struct f_owner_ex * __user owner_p = (void * __user)arg;
+ struct f_owner_ex owner;
+ struct pid *pid;
+ int type;
+ int ret;
+
+ ret = copy_from_user(&owner, owner_p, sizeof(owner));
+ if (ret)
+ return ret;
+
+ switch (owner.type) {
+ case F_OWNER_TID:
+ type = PIDTYPE_MAX;
+ break;
+
+ case F_OWNER_PID:
+ type = PIDTYPE_PID;
+ break;
+
+ case F_OWNER_GID:
+ type = PIDTYPE_PGID;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ rcu_read_lock();
+ pid = find_vpid(owner.pid);
+ if (owner.pid && !pid)
+ ret = -ESRCH;
+ else
+ ret = __f_setown(filp, pid, type, 1);
+ rcu_read_unlock();
+
+ return ret;
+}
+
+static int f_getown_ex(struct file *filp, unsigned long arg)
+{
+ struct f_owner_ex * __user owner_p = (void * __user)arg;
+ struct f_owner_ex owner;
+ int ret = 0;
+
+ read_lock(&filp->f_owner.lock);
+ owner.pid = pid_vnr(filp->f_owner.pid);
+ switch (filp->f_owner.pid_type) {
+ case PIDTYPE_MAX:
+ owner.type = F_OWNER_TID;
+ break;
+
+ case PIDTYPE_PID:
+ owner.type = F_OWNER_PID;
+ break;
+
+ case PIDTYPE_PGID:
+ owner.type = F_OWNER_GID;
+ break;
+
+ default:
+ WARN_ON(1);
+ ret = -EINVAL;
+ break;
+ }
+ read_unlock(&filp->f_owner.lock);
+
+ if (!ret)
+ ret = copy_to_user(owner_p, &owner, sizeof(owner));
+ return ret;
+}
+
static long do_fcntl(int fd, unsigned int cmd, unsigned long arg,
struct file *filp)
{
case F_SETOWN:
err = f_setown(filp, arg, 1);
break;
+ case F_GETOWN_EX:
+ err = f_getown_ex(filp, arg);
+ break;
+ case F_SETOWN_EX:
+ err = f_setown_ex(filp, arg);
+ break;
case F_GETSIG:
err = filp->f_owner.signum;
break;
static void send_sigio_to_task(struct task_struct *p,
struct fown_struct *fown,
- int fd,
- int reason)
+ int fd, int reason, int group)
{
/*
* F_SETSIG can change ->signum lockless in parallel, make
else
si.si_band = band_table[reason - POLL_IN];
si.si_fd = fd;
- if (!group_send_sig_info(signum, &si, p))
+ if (!do_send_sig_info(signum, &si, p, group))
break;
/* fall-through: fall back on the old plain SIGIO signal */
case 0:
- group_send_sig_info(SIGIO, SEND_SIG_PRIV, p);
+ do_send_sig_info(SIGIO, SEND_SIG_PRIV, p, group);
}
}
struct task_struct *p;
enum pid_type type;
struct pid *pid;
+ int group = 1;
read_lock(&fown->lock);
+
type = fown->pid_type;
+ if (type == PIDTYPE_MAX) {
+ group = 0;
+ type = PIDTYPE_PID;
+ }
+
pid = fown->pid;
if (!pid)
goto out_unlock_fown;
read_lock(&tasklist_lock);
do_each_pid_task(pid, type, p) {
- send_sigio_to_task(p, fown, fd, band);
+ send_sigio_to_task(p, fown, fd, band, group);
} while_each_pid_task(pid, type, p);
read_unlock(&tasklist_lock);
out_unlock_fown:
}
static void send_sigurg_to_task(struct task_struct *p,
- struct fown_struct *fown)
+ struct fown_struct *fown, int group)
{
if (sigio_perm(p, fown, SIGURG))
- group_send_sig_info(SIGURG, SEND_SIG_PRIV, p);
+ do_send_sig_info(SIGURG, SEND_SIG_PRIV, p, group);
}
int send_sigurg(struct fown_struct *fown)
struct task_struct *p;
enum pid_type type;
struct pid *pid;
+ int group = 1;
int ret = 0;
read_lock(&fown->lock);
+
type = fown->pid_type;
+ if (type == PIDTYPE_MAX) {
+ group = 0;
+ type = PIDTYPE_PID;
+ }
+
pid = fown->pid;
if (!pid)
goto out_unlock_fown;
read_lock(&tasklist_lock);
do_each_pid_task(pid, type, p) {
- send_sigurg_to_task(p, fown);
+ send_sigurg_to_task(p, fown, group);
} while_each_pid_task(pid, type, p);
read_unlock(&tasklist_lock);
out_unlock_fown:
* Handle nr_files sysctl
*/
#if defined(CONFIG_SYSCTL) && defined(CONFIG_PROC_FS)
-int proc_nr_files(ctl_table *table, int write, struct file *filp,
+int proc_nr_files(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
files_stat.nr_files = get_nr_files();
- return proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ return proc_dointvec(table, write, buffer, lenp, ppos);
}
#else
-int proc_nr_files(ctl_table *table, int write, struct file *filp,
+int proc_nr_files(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
long nr_pages;
struct super_block *sb;
enum writeback_sync_modes sync_mode;
- int for_kupdate;
- int range_cyclic;
+ int for_kupdate:1;
+ int range_cyclic:1;
+ int for_background:1;
};
/*
* completion. Caller need not hold sb s_umount semaphore.
*
*/
-void bdi_start_writeback(struct backing_dev_info *bdi, long nr_pages)
+void bdi_start_writeback(struct backing_dev_info *bdi, struct super_block *sb,
+ long nr_pages)
{
struct wb_writeback_args args = {
+ .sb = sb,
.sync_mode = WB_SYNC_NONE,
.nr_pages = nr_pages,
.range_cyclic = 1,
};
+ /*
+ * We treat @nr_pages=0 as the special case to do background writeback,
+ * ie. to sync pages until the background dirty threshold is reached.
+ */
+ if (!nr_pages) {
+ args.nr_pages = LONG_MAX;
+ args.for_background = 1;
+ }
+
bdi_alloc_queue_work(bdi, &args);
}
* For inodes being constantly redirtied, dirtied_when can get stuck.
* It _appears_ to be in the future, but is actually in distant past.
* This test is necessary to prevent such wrapped-around relative times
- * from permanently stopping the whole pdflush writeback.
+ * from permanently stopping the whole bdi writeback.
*/
ret = ret && time_before_eq(inode->dirtied_when, jiffies);
#endif
struct list_head *dispatch_queue,
unsigned long *older_than_this)
{
+ LIST_HEAD(tmp);
+ struct list_head *pos, *node;
+ struct super_block *sb = NULL;
+ struct inode *inode;
+ int do_sb_sort = 0;
+
while (!list_empty(delaying_queue)) {
- struct inode *inode = list_entry(delaying_queue->prev,
- struct inode, i_list);
+ inode = list_entry(delaying_queue->prev, struct inode, i_list);
if (older_than_this &&
inode_dirtied_after(inode, *older_than_this))
break;
- list_move(&inode->i_list, dispatch_queue);
+ if (sb && sb != inode->i_sb)
+ do_sb_sort = 1;
+ sb = inode->i_sb;
+ list_move(&inode->i_list, &tmp);
+ }
+
+ /* just one sb in list, splice to dispatch_queue and we're done */
+ if (!do_sb_sort) {
+ list_splice(&tmp, dispatch_queue);
+ return;
+ }
+
+ /* Move inodes from one superblock together */
+ while (!list_empty(&tmp)) {
+ inode = list_entry(tmp.prev, struct inode, i_list);
+ sb = inode->i_sb;
+ list_for_each_prev_safe(pos, node, &tmp) {
+ inode = list_entry(pos, struct inode, i_list);
+ if (inode->i_sb == sb)
+ list_move(&inode->i_list, dispatch_queue);
+ }
}
}
spin_lock(&inode_lock);
inode->i_state &= ~I_SYNC;
if (!(inode->i_state & (I_FREEING | I_CLEAR))) {
- if (!(inode->i_state & I_DIRTY) &&
- mapping_tagged(mapping, PAGECACHE_TAG_DIRTY)) {
+ if ((inode->i_state & I_DIRTY_PAGES) && wbc->for_kupdate) {
+ /*
+ * More pages get dirtied by a fast dirtier.
+ */
+ goto select_queue;
+ } else if (inode->i_state & I_DIRTY) {
+ /*
+ * At least XFS will redirty the inode during the
+ * writeback (delalloc) and on io completion (isize).
+ */
+ redirty_tail(inode);
+ } else if (mapping_tagged(mapping, PAGECACHE_TAG_DIRTY)) {
/*
* We didn't write back all the pages. nfs_writepages()
* sometimes bales out without doing anything. Redirty
* soon as the queue becomes uncongested.
*/
inode->i_state |= I_DIRTY_PAGES;
+select_queue:
if (wbc->nr_to_write <= 0) {
/*
* slice used up: queue for next turn
inode->i_state |= I_DIRTY_PAGES;
redirty_tail(inode);
}
- } else if (inode->i_state & I_DIRTY) {
- /*
- * Someone redirtied the inode while were writing back
- * the pages.
- */
- redirty_tail(inode);
} else if (atomic_read(&inode->i_count)) {
/*
* The inode is clean, inuse
return ret;
}
+static void unpin_sb_for_writeback(struct super_block **psb)
+{
+ struct super_block *sb = *psb;
+
+ if (sb) {
+ up_read(&sb->s_umount);
+ put_super(sb);
+ *psb = NULL;
+ }
+}
+
/*
* For WB_SYNC_NONE writeback, the caller does not have the sb pinned
* before calling writeback. So make sure that we do pin it, so it doesn't
* 1 if we failed.
*/
static int pin_sb_for_writeback(struct writeback_control *wbc,
- struct inode *inode)
+ struct inode *inode, struct super_block **psb)
{
struct super_block *sb = inode->i_sb;
+ /*
+ * If this sb is already pinned, nothing more to do. If not and
+ * *psb is non-NULL, unpin the old one first
+ */
+ if (sb == *psb)
+ return 0;
+ else if (*psb)
+ unpin_sb_for_writeback(psb);
+
/*
* Caller must already hold the ref for this
*/
if (down_read_trylock(&sb->s_umount)) {
if (sb->s_root) {
spin_unlock(&sb_lock);
- return 0;
+ goto pinned;
}
/*
* umounted, drop rwsem again and fall through to failure
sb->s_count--;
spin_unlock(&sb_lock);
return 1;
-}
-
-static void unpin_sb_for_writeback(struct writeback_control *wbc,
- struct inode *inode)
-{
- struct super_block *sb = inode->i_sb;
-
- if (wbc->sync_mode == WB_SYNC_ALL)
- return;
-
- up_read(&sb->s_umount);
- put_super(sb);
+pinned:
+ *psb = sb;
+ return 0;
}
static void writeback_inodes_wb(struct bdi_writeback *wb,
struct writeback_control *wbc)
{
- struct super_block *sb = wbc->sb;
+ struct super_block *sb = wbc->sb, *pin_sb = NULL;
const int is_blkdev_sb = sb_is_blkdev_sb(sb);
const unsigned long start = jiffies; /* livelock avoidance */
if (inode_dirtied_after(inode, start))
break;
- if (pin_sb_for_writeback(wbc, inode)) {
+ if (pin_sb_for_writeback(wbc, inode, &pin_sb)) {
requeue_io(inode);
continue;
}
__iget(inode);
pages_skipped = wbc->pages_skipped;
writeback_single_inode(inode, wbc);
- unpin_sb_for_writeback(wbc, inode);
if (wbc->pages_skipped != pages_skipped) {
/*
* writeback is not making progress due to locked
wbc->more_io = 1;
}
+ unpin_sb_for_writeback(&pin_sb);
+
spin_unlock(&inode_lock);
/* Leave any unwritten inodes on b_io */
}
};
unsigned long oldest_jif;
long wrote = 0;
+ struct inode *inode;
if (wbc.for_kupdate) {
wbc.older_than_this = &oldest_jif;
for (;;) {
/*
- * Don't flush anything for non-integrity writeback where
- * no nr_pages was given
+ * Stop writeback when nr_pages has been consumed
*/
- if (!args->for_kupdate && args->nr_pages <= 0 &&
- args->sync_mode == WB_SYNC_NONE)
+ if (args->nr_pages <= 0)
break;
/*
- * If no specific pages were given and this is just a
- * periodic background writeout and we are below the
- * background dirty threshold, don't do anything
+ * For background writeout, stop when we are below the
+ * background dirty threshold
*/
- if (args->for_kupdate && args->nr_pages <= 0 &&
- !over_bground_thresh())
+ if (args->for_background && !over_bground_thresh())
break;
wbc.more_io = 0;
wrote += MAX_WRITEBACK_PAGES - wbc.nr_to_write;
/*
- * If we ran out of stuff to write, bail unless more_io got set
+ * If we consumed everything, see if we have more
*/
- if (wbc.nr_to_write > 0 || wbc.pages_skipped > 0) {
- if (wbc.more_io && !wbc.for_kupdate)
- continue;
+ if (wbc.nr_to_write <= 0)
+ continue;
+ /*
+ * Didn't write everything and we don't have more IO, bail
+ */
+ if (!wbc.more_io)
break;
+ /*
+ * Did we write something? Try for more
+ */
+ if (wbc.nr_to_write < MAX_WRITEBACK_PAGES)
+ continue;
+ /*
+ * Nothing written. Wait for some inode to
+ * become available for writeback. Otherwise
+ * we'll just busyloop.
+ */
+ spin_lock(&inode_lock);
+ if (!list_empty(&wb->b_more_io)) {
+ inode = list_entry(wb->b_more_io.prev,
+ struct inode, i_list);
+ inode_wait_for_writeback(inode);
}
+ spin_unlock(&inode_lock);
}
return wrote;
* If older_than_this is non-NULL, then only write out inodes which
* had their first dirtying at a time earlier than *older_than_this.
*
- * If we're a pdlfush thread, then implement pdflush collision avoidance
- * against the entire list.
- *
* If `bdi' is non-zero then we're being asked to writeback a specific queue.
* This function assumes that the blockdev superblock's inodes are backed by
* a variety of queues, so all inodes are searched. For other superblocks,
nr_to_write = nr_dirty + nr_unstable +
(inodes_stat.nr_inodes - inodes_stat.nr_unused);
- bdi_writeback_all(sb, nr_to_write);
+ bdi_start_writeback(sb->s_bdi, sb, nr_to_write);
}
EXPORT_SYMBOL(writeback_inodes_sb);
return 0;
if (attr->ia_valid & ATTR_SIZE) {
- unsigned long limit;
- if (IS_SWAPFILE(inode))
- return -ETXTBSY;
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && attr->ia_size > (loff_t) limit) {
- send_sig(SIGXFSZ, current, 0);
- return -EFBIG;
- }
+ err = inode_newsize_ok(inode, attr->ia_size);
+ if (err)
+ return err;
is_truncate = true;
}
* FUSE_NOWRITE, otherwise fuse_launder_page() would deadlock.
*/
if (S_ISREG(inode->i_mode) && oldsize != outarg.attr.size) {
- if (outarg.attr.size < oldsize)
- fuse_truncate(inode->i_mapping, outarg.attr.size);
+ truncate_pagecache(inode, oldsize, outarg.attr.size);
invalidate_inode_pages2(inode->i_mapping);
}
return 0;
}
-static struct vm_operations_struct fuse_file_vm_ops = {
+static const struct vm_operations_struct fuse_file_vm_ops = {
.close = fuse_vma_close,
.fault = filemap_fault,
.page_mkwrite = fuse_page_mkwrite,
void fuse_change_attributes_common(struct inode *inode, struct fuse_attr *attr,
u64 attr_valid);
-void fuse_truncate(struct address_space *mapping, loff_t offset);
-
/**
* Initialize the client device
*/
return 0;
}
-void fuse_truncate(struct address_space *mapping, loff_t offset)
-{
- /* See vmtruncate() */
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- truncate_inode_pages(mapping, offset);
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
-}
-
void fuse_change_attributes_common(struct inode *inode, struct fuse_attr *attr,
u64 attr_valid)
{
spin_unlock(&fc->lock);
if (S_ISREG(inode->i_mode) && oldsize != attr->size) {
- if (attr->size < oldsize)
- fuse_truncate(inode->i_mapping, attr->size);
+ truncate_pagecache(inode, oldsize, attr->size);
invalidate_inode_pages2(inode->i_mapping);
}
}
.direct_IO = gfs2_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations gfs2_ordered_aops = {
.direct_IO = gfs2_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
static const struct address_space_operations gfs2_jdata_aops = {
.invalidatepage = gfs2_invalidatepage,
.releasepage = gfs2_releasepage,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
void gfs2_set_aops(struct inode *inode)
return ret;
}
-static struct vm_operations_struct gfs2_vm_ops = {
+static const struct vm_operations_struct gfs2_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = gfs2_page_mkwrite,
};
brelse(HFS_SB(sb)->mdb_bh);
brelse(HFS_SB(sb)->alt_mdb_bh);
- if (HFS_SB(sb)->nls_io)
- unload_nls(HFS_SB(sb)->nls_io);
- if (HFS_SB(sb)->nls_disk)
- unload_nls(HFS_SB(sb)->nls_disk);
+ unload_nls(HFS_SB(sb)->nls_io);
+ unload_nls(HFS_SB(sb)->nls_disk);
free_pages((unsigned long)HFS_SB(sb)->bitmap, PAGE_SIZE < 8192 ? 1 : 0);
kfree(HFS_SB(sb));
iput(HFSPLUS_SB(sb).alloc_file);
iput(HFSPLUS_SB(sb).hidden_dir);
brelse(HFSPLUS_SB(sb).s_vhbh);
- if (HFSPLUS_SB(sb).nls)
- unload_nls(HFSPLUS_SB(sb).nls);
+ unload_nls(HFSPLUS_SB(sb).nls);
kfree(sb->s_fs_info);
sb->s_fs_info = NULL;
cleanup:
hfsplus_put_super(sb);
- if (nls)
- unload_nls(nls);
+ unload_nls(nls);
return err;
}
static void hugetlbfs_forget_inode(struct inode *inode) __releases(inode_lock)
{
- struct super_block *sb = inode->i_sb;
-
- if (!hlist_unhashed(&inode->i_hash)) {
- if (!(inode->i_state & (I_DIRTY|I_SYNC)))
- list_move(&inode->i_list, &inode_unused);
- inodes_stat.nr_unused++;
- if (!sb || (sb->s_flags & MS_ACTIVE)) {
- spin_unlock(&inode_lock);
- return;
- }
- inode->i_state |= I_WILL_FREE;
- spin_unlock(&inode_lock);
- /*
- * write_inode_now is a noop as we set BDI_CAP_NO_WRITEBACK
- * in our backing_dev_info.
- */
- write_inode_now(inode, 1);
- spin_lock(&inode_lock);
- inode->i_state &= ~I_WILL_FREE;
- inodes_stat.nr_unused--;
- hlist_del_init(&inode->i_hash);
+ if (generic_detach_inode(inode)) {
+ truncate_hugepages(inode, 0);
+ clear_inode(inode);
+ destroy_inode(inode);
}
- list_del_init(&inode->i_list);
- list_del_init(&inode->i_sb_list);
- inode->i_state |= I_FREEING;
- inodes_stat.nr_inodes--;
- spin_unlock(&inode_lock);
- truncate_hugepages(inode, 0);
- clear_inode(inode);
- destroy_inode(inode);
}
static void hugetlbfs_drop_inode(struct inode *inode)
static struct vfsmount *hugetlbfs_vfsmount;
-static int can_do_hugetlb_shm(int creat_flags)
+static int can_do_hugetlb_shm(void)
{
- if (creat_flags != HUGETLB_SHMFS_INODE)
- return 0;
- if (capable(CAP_IPC_LOCK))
- return 1;
- if (in_group_p(sysctl_hugetlb_shm_group))
- return 1;
- return 0;
+ return capable(CAP_IPC_LOCK) || in_group_p(sysctl_hugetlb_shm_group);
}
struct file *hugetlb_file_setup(const char *name, size_t size, int acctflag,
if (!hugetlbfs_vfsmount)
return ERR_PTR(-ENOENT);
- if (!can_do_hugetlb_shm(creat_flags)) {
+ if (creat_flags == HUGETLB_SHMFS_INODE && !can_do_hugetlb_shm()) {
*user = current_user();
if (user_shm_lock(size, *user)) {
WARN_ONCE(1,
}
EXPORT_SYMBOL(generic_delete_inode);
-static void generic_forget_inode(struct inode *inode)
+/**
+ * generic_detach_inode - remove inode from inode lists
+ * @inode: inode to remove
+ *
+ * Remove inode from inode lists, write it if it's dirty. This is just an
+ * internal VFS helper exported for hugetlbfs. Do not use!
+ *
+ * Returns 1 if inode should be completely destroyed.
+ */
+int generic_detach_inode(struct inode *inode)
{
struct super_block *sb = inode->i_sb;
inodes_stat.nr_unused++;
if (sb->s_flags & MS_ACTIVE) {
spin_unlock(&inode_lock);
- return;
+ return 0;
}
WARN_ON(inode->i_state & I_NEW);
inode->i_state |= I_WILL_FREE;
inode->i_state |= I_FREEING;
inodes_stat.nr_inodes--;
spin_unlock(&inode_lock);
+ return 1;
+}
+EXPORT_SYMBOL_GPL(generic_detach_inode);
+
+static void generic_forget_inode(struct inode *inode)
+{
+ if (!generic_detach_inode(inode))
+ return;
if (inode->i_data.nrpages)
truncate_inode_pages(&inode->i_data, 0);
clear_inode(inode);
struct inode *inode = dentry->d_inode;
struct timespec now;
- if (mnt_want_write(mnt))
- return;
if (inode->i_flags & S_NOATIME)
- goto out;
+ return;
if (IS_NOATIME(inode))
- goto out;
+ return;
if ((inode->i_sb->s_flags & MS_NODIRATIME) && S_ISDIR(inode->i_mode))
- goto out;
+ return;
if (mnt->mnt_flags & MNT_NOATIME)
- goto out;
+ return;
if ((mnt->mnt_flags & MNT_NODIRATIME) && S_ISDIR(inode->i_mode))
- goto out;
+ return;
now = current_fs_time(inode->i_sb);
if (!relatime_need_update(mnt, inode, now))
- goto out;
+ return;
if (timespec_equal(&inode->i_atime, &now))
- goto out;
+ return;
+
+ if (mnt_want_write(mnt))
+ return;
inode->i_atime = now;
mark_inode_dirty_sync(inode);
-out:
mnt_drop_write(mnt);
}
EXPORT_SYMBOL(touch_atime);
{
struct inode *inode = file->f_path.dentry->d_inode;
struct timespec now;
- int sync_it = 0;
- int err;
+ enum { S_MTIME = 1, S_CTIME = 2, S_VERSION = 4 } sync_it = 0;
+ /* First try to exhaust all avenues to not sync */
if (IS_NOCMTIME(inode))
return;
- err = mnt_want_write_file(file);
- if (err)
- return;
-
now = current_fs_time(inode->i_sb);
- if (!timespec_equal(&inode->i_mtime, &now)) {
- inode->i_mtime = now;
- sync_it = 1;
- }
+ if (!timespec_equal(&inode->i_mtime, &now))
+ sync_it = S_MTIME;
- if (!timespec_equal(&inode->i_ctime, &now)) {
- inode->i_ctime = now;
- sync_it = 1;
- }
+ if (!timespec_equal(&inode->i_ctime, &now))
+ sync_it |= S_CTIME;
- if (IS_I_VERSION(inode)) {
- inode_inc_iversion(inode);
- sync_it = 1;
- }
+ if (IS_I_VERSION(inode))
+ sync_it |= S_VERSION;
+
+ if (!sync_it)
+ return;
- if (sync_it)
- mark_inode_dirty_sync(inode);
+ /* Finally allowed to write? Takes lock. */
+ if (mnt_want_write_file(file))
+ return;
+
+ /* Only change inode inside the lock region */
+ if (sync_it & S_VERSION)
+ inode_inc_iversion(inode);
+ if (sync_it & S_CTIME)
+ inode->i_ctime = now;
+ if (sync_it & S_MTIME)
+ inode->i_mtime = now;
+ mark_inode_dirty_sync(inode);
mnt_drop_write(file->f_path.mnt);
}
EXPORT_SYMBOL(file_update_time);
else if (S_ISSOCK(mode))
inode->i_fop = &bad_sock_fops;
else
- printk(KERN_DEBUG "init_special_inode: bogus i_mode (%o)\n",
- mode);
+ printk(KERN_DEBUG "init_special_inode: bogus i_mode (%o) for"
+ " inode %s:%lu\n", mode, inode->i_sb->s_id,
+ inode->i_ino);
}
EXPORT_SYMBOL(init_special_inode);
* namespace.c
*/
extern int copy_mount_options(const void __user *, unsigned long *);
+extern int copy_mount_string(const void __user *, char **);
extern void free_vfsmnt(struct vfsmount *);
extern struct vfsmount *alloc_vfsmnt(const char *);
static int fiemap_check_ranges(struct super_block *sb,
u64 start, u64 len, u64 *new_len)
{
+ u64 maxbytes = (u64) sb->s_maxbytes;
+
*new_len = len;
if (len == 0)
return -EINVAL;
- if (start > sb->s_maxbytes)
+ if (start > maxbytes)
return -EFBIG;
/*
* Shrink request scope to what the fs can actually handle.
*/
- if ((len > sb->s_maxbytes) ||
- (sb->s_maxbytes - len) < start)
- *new_len = sb->s_maxbytes - start;
+ if (len > maxbytes || (maxbytes - len) < start)
+ *new_len = maxbytes - start;
return 0;
}
#ifdef CONFIG_JOLIET
lock_kernel();
- if (sbi->s_nls_iocharset) {
- unload_nls(sbi->s_nls_iocharset);
- sbi->s_nls_iocharset = NULL;
- }
+ unload_nls(sbi->s_nls_iocharset);
unlock_kernel();
#endif
printk(KERN_WARNING "%s: get root inode failed\n", __func__);
out_no_inode:
#ifdef CONFIG_JOLIET
- if (sbi->s_nls_iocharset)
- unload_nls(sbi->s_nls_iocharset);
+ unload_nls(sbi->s_nls_iocharset);
#endif
goto out_freesbi;
out_no_read:
int __jbd2_journal_remove_checkpoint(struct journal_head *jh)
{
+ struct transaction_chp_stats_s *stats;
transaction_t *transaction;
journal_t *journal;
int ret = 0;
/* OK, that was the last buffer for the transaction: we can now
safely remove this transaction from the log */
+ stats = &transaction->t_chp_stats;
+ if (stats->cs_chp_time)
+ stats->cs_chp_time = jbd2_time_diff(stats->cs_chp_time,
+ jiffies);
+ trace_jbd2_checkpoint_stats(journal->j_fs_dev->bd_dev,
+ transaction->t_tid, stats);
__jbd2_journal_drop_transaction(journal, transaction);
kfree(transaction);
if (commit_transaction->t_synchronous_commit)
write_op = WRITE_SYNC_PLUG;
trace_jbd2_commit_locking(journal, commit_transaction);
- stats.u.run.rs_wait = commit_transaction->t_max_wait;
- stats.u.run.rs_locked = jiffies;
- stats.u.run.rs_running = jbd2_time_diff(commit_transaction->t_start,
- stats.u.run.rs_locked);
+ stats.run.rs_wait = commit_transaction->t_max_wait;
+ stats.run.rs_locked = jiffies;
+ stats.run.rs_running = jbd2_time_diff(commit_transaction->t_start,
+ stats.run.rs_locked);
spin_lock(&commit_transaction->t_handle_lock);
while (commit_transaction->t_updates) {
jbd2_journal_switch_revoke_table(journal);
trace_jbd2_commit_flushing(journal, commit_transaction);
- stats.u.run.rs_flushing = jiffies;
- stats.u.run.rs_locked = jbd2_time_diff(stats.u.run.rs_locked,
- stats.u.run.rs_flushing);
+ stats.run.rs_flushing = jiffies;
+ stats.run.rs_locked = jbd2_time_diff(stats.run.rs_locked,
+ stats.run.rs_flushing);
commit_transaction->t_state = T_FLUSH;
journal->j_committing_transaction = commit_transaction;
spin_unlock(&journal->j_state_lock);
trace_jbd2_commit_logging(journal, commit_transaction);
- stats.u.run.rs_logging = jiffies;
- stats.u.run.rs_flushing = jbd2_time_diff(stats.u.run.rs_flushing,
- stats.u.run.rs_logging);
- stats.u.run.rs_blocks = commit_transaction->t_outstanding_credits;
- stats.u.run.rs_blocks_logged = 0;
+ stats.run.rs_logging = jiffies;
+ stats.run.rs_flushing = jbd2_time_diff(stats.run.rs_flushing,
+ stats.run.rs_logging);
+ stats.run.rs_blocks = commit_transaction->t_outstanding_credits;
+ stats.run.rs_blocks_logged = 0;
J_ASSERT(commit_transaction->t_nr_buffers <=
commit_transaction->t_outstanding_credits);
submit_bh(write_op, bh);
}
cond_resched();
- stats.u.run.rs_blocks_logged += bufs;
+ stats.run.rs_blocks_logged += bufs;
/* Force a new descriptor to be generated next
time round the loop. */
J_ASSERT(commit_transaction->t_state == T_COMMIT);
commit_transaction->t_start = jiffies;
- stats.u.run.rs_logging = jbd2_time_diff(stats.u.run.rs_logging,
- commit_transaction->t_start);
+ stats.run.rs_logging = jbd2_time_diff(stats.run.rs_logging,
+ commit_transaction->t_start);
/*
- * File the transaction for history
+ * File the transaction statistics
*/
- stats.ts_type = JBD2_STATS_RUN;
stats.ts_tid = commit_transaction->t_tid;
- stats.u.run.rs_handle_count = commit_transaction->t_handle_count;
- spin_lock(&journal->j_history_lock);
- memcpy(journal->j_history + journal->j_history_cur, &stats,
- sizeof(stats));
- if (++journal->j_history_cur == journal->j_history_max)
- journal->j_history_cur = 0;
+ stats.run.rs_handle_count = commit_transaction->t_handle_count;
+ trace_jbd2_run_stats(journal->j_fs_dev->bd_dev,
+ commit_transaction->t_tid, &stats.run);
/*
* Calculate overall stats
*/
+ spin_lock(&journal->j_history_lock);
journal->j_stats.ts_tid++;
- journal->j_stats.u.run.rs_wait += stats.u.run.rs_wait;
- journal->j_stats.u.run.rs_running += stats.u.run.rs_running;
- journal->j_stats.u.run.rs_locked += stats.u.run.rs_locked;
- journal->j_stats.u.run.rs_flushing += stats.u.run.rs_flushing;
- journal->j_stats.u.run.rs_logging += stats.u.run.rs_logging;
- journal->j_stats.u.run.rs_handle_count += stats.u.run.rs_handle_count;
- journal->j_stats.u.run.rs_blocks += stats.u.run.rs_blocks;
- journal->j_stats.u.run.rs_blocks_logged += stats.u.run.rs_blocks_logged;
+ journal->j_stats.run.rs_wait += stats.run.rs_wait;
+ journal->j_stats.run.rs_running += stats.run.rs_running;
+ journal->j_stats.run.rs_locked += stats.run.rs_locked;
+ journal->j_stats.run.rs_flushing += stats.run.rs_flushing;
+ journal->j_stats.run.rs_logging += stats.run.rs_logging;
+ journal->j_stats.run.rs_handle_count += stats.run.rs_handle_count;
+ journal->j_stats.run.rs_blocks += stats.run.rs_blocks;
+ journal->j_stats.run.rs_blocks_logged += stats.run.rs_blocks_logged;
spin_unlock(&journal->j_history_lock);
commit_transaction->t_state = T_FINISHED;
journal->j_task = current;
wake_up(&journal->j_wait_done_commit);
- printk(KERN_INFO "kjournald2 starting: pid %d, dev %s, "
- "commit interval %ld seconds\n", current->pid,
- journal->j_devname, journal->j_commit_interval / HZ);
-
/*
* And now, wait forever for commit wakeup events.
*/
{
struct task_struct *t;
- t = kthread_run(kjournald2, journal, "kjournald2");
+ t = kthread_run(kjournald2, journal, "jbd2/%s",
+ journal->j_devname);
if (IS_ERR(t))
return PTR_ERR(t);
int max;
};
-static void *jbd2_history_skip_empty(struct jbd2_stats_proc_session *s,
- struct transaction_stats_s *ts,
- int first)
-{
- if (ts == s->stats + s->max)
- ts = s->stats;
- if (!first && ts == s->stats + s->start)
- return NULL;
- while (ts->ts_type == 0) {
- ts++;
- if (ts == s->stats + s->max)
- ts = s->stats;
- if (ts == s->stats + s->start)
- return NULL;
- }
- return ts;
-
-}
-
-static void *jbd2_seq_history_start(struct seq_file *seq, loff_t *pos)
-{
- struct jbd2_stats_proc_session *s = seq->private;
- struct transaction_stats_s *ts;
- int l = *pos;
-
- if (l == 0)
- return SEQ_START_TOKEN;
- ts = jbd2_history_skip_empty(s, s->stats + s->start, 1);
- if (!ts)
- return NULL;
- l--;
- while (l) {
- ts = jbd2_history_skip_empty(s, ++ts, 0);
- if (!ts)
- break;
- l--;
- }
- return ts;
-}
-
-static void *jbd2_seq_history_next(struct seq_file *seq, void *v, loff_t *pos)
-{
- struct jbd2_stats_proc_session *s = seq->private;
- struct transaction_stats_s *ts = v;
-
- ++*pos;
- if (v == SEQ_START_TOKEN)
- return jbd2_history_skip_empty(s, s->stats + s->start, 1);
- else
- return jbd2_history_skip_empty(s, ++ts, 0);
-}
-
-static int jbd2_seq_history_show(struct seq_file *seq, void *v)
-{
- struct transaction_stats_s *ts = v;
- if (v == SEQ_START_TOKEN) {
- seq_printf(seq, "%-4s %-5s %-5s %-5s %-5s %-5s %-5s %-6s %-5s "
- "%-5s %-5s %-5s %-5s %-5s\n", "R/C", "tid",
- "wait", "run", "lock", "flush", "log", "hndls",
- "block", "inlog", "ctime", "write", "drop",
- "close");
- return 0;
- }
- if (ts->ts_type == JBD2_STATS_RUN)
- seq_printf(seq, "%-4s %-5lu %-5u %-5u %-5u %-5u %-5u "
- "%-6lu %-5lu %-5lu\n", "R", ts->ts_tid,
- jiffies_to_msecs(ts->u.run.rs_wait),
- jiffies_to_msecs(ts->u.run.rs_running),
- jiffies_to_msecs(ts->u.run.rs_locked),
- jiffies_to_msecs(ts->u.run.rs_flushing),
- jiffies_to_msecs(ts->u.run.rs_logging),
- ts->u.run.rs_handle_count,
- ts->u.run.rs_blocks,
- ts->u.run.rs_blocks_logged);
- else if (ts->ts_type == JBD2_STATS_CHECKPOINT)
- seq_printf(seq, "%-4s %-5lu %48s %-5u %-5lu %-5lu %-5lu\n",
- "C", ts->ts_tid, " ",
- jiffies_to_msecs(ts->u.chp.cs_chp_time),
- ts->u.chp.cs_written, ts->u.chp.cs_dropped,
- ts->u.chp.cs_forced_to_close);
- else
- J_ASSERT(0);
- return 0;
-}
-
-static void jbd2_seq_history_stop(struct seq_file *seq, void *v)
-{
-}
-
-static const struct seq_operations jbd2_seq_history_ops = {
- .start = jbd2_seq_history_start,
- .next = jbd2_seq_history_next,
- .stop = jbd2_seq_history_stop,
- .show = jbd2_seq_history_show,
-};
-
-static int jbd2_seq_history_open(struct inode *inode, struct file *file)
-{
- journal_t *journal = PDE(inode)->data;
- struct jbd2_stats_proc_session *s;
- int rc, size;
-
- s = kmalloc(sizeof(*s), GFP_KERNEL);
- if (s == NULL)
- return -ENOMEM;
- size = sizeof(struct transaction_stats_s) * journal->j_history_max;
- s->stats = kmalloc(size, GFP_KERNEL);
- if (s->stats == NULL) {
- kfree(s);
- return -ENOMEM;
- }
- spin_lock(&journal->j_history_lock);
- memcpy(s->stats, journal->j_history, size);
- s->max = journal->j_history_max;
- s->start = journal->j_history_cur % s->max;
- spin_unlock(&journal->j_history_lock);
-
- rc = seq_open(file, &jbd2_seq_history_ops);
- if (rc == 0) {
- struct seq_file *m = file->private_data;
- m->private = s;
- } else {
- kfree(s->stats);
- kfree(s);
- }
- return rc;
-
-}
-
-static int jbd2_seq_history_release(struct inode *inode, struct file *file)
-{
- struct seq_file *seq = file->private_data;
- struct jbd2_stats_proc_session *s = seq->private;
-
- kfree(s->stats);
- kfree(s);
- return seq_release(inode, file);
-}
-
-static struct file_operations jbd2_seq_history_fops = {
- .owner = THIS_MODULE,
- .open = jbd2_seq_history_open,
- .read = seq_read,
- .llseek = seq_lseek,
- .release = jbd2_seq_history_release,
-};
-
static void *jbd2_seq_info_start(struct seq_file *seq, loff_t *pos)
{
return *pos ? NULL : SEQ_START_TOKEN;
if (v != SEQ_START_TOKEN)
return 0;
- seq_printf(seq, "%lu transaction, each upto %u blocks\n",
+ seq_printf(seq, "%lu transaction, each up to %u blocks\n",
s->stats->ts_tid,
s->journal->j_max_transaction_buffers);
if (s->stats->ts_tid == 0)
return 0;
seq_printf(seq, "average: \n %ums waiting for transaction\n",
- jiffies_to_msecs(s->stats->u.run.rs_wait / s->stats->ts_tid));
+ jiffies_to_msecs(s->stats->run.rs_wait / s->stats->ts_tid));
seq_printf(seq, " %ums running transaction\n",
- jiffies_to_msecs(s->stats->u.run.rs_running / s->stats->ts_tid));
+ jiffies_to_msecs(s->stats->run.rs_running / s->stats->ts_tid));
seq_printf(seq, " %ums transaction was being locked\n",
- jiffies_to_msecs(s->stats->u.run.rs_locked / s->stats->ts_tid));
+ jiffies_to_msecs(s->stats->run.rs_locked / s->stats->ts_tid));
seq_printf(seq, " %ums flushing data (in ordered mode)\n",
- jiffies_to_msecs(s->stats->u.run.rs_flushing / s->stats->ts_tid));
+ jiffies_to_msecs(s->stats->run.rs_flushing / s->stats->ts_tid));
seq_printf(seq, " %ums logging transaction\n",
- jiffies_to_msecs(s->stats->u.run.rs_logging / s->stats->ts_tid));
+ jiffies_to_msecs(s->stats->run.rs_logging / s->stats->ts_tid));
seq_printf(seq, " %lluus average transaction commit time\n",
div_u64(s->journal->j_average_commit_time, 1000));
seq_printf(seq, " %lu handles per transaction\n",
- s->stats->u.run.rs_handle_count / s->stats->ts_tid);
+ s->stats->run.rs_handle_count / s->stats->ts_tid);
seq_printf(seq, " %lu blocks per transaction\n",
- s->stats->u.run.rs_blocks / s->stats->ts_tid);
+ s->stats->run.rs_blocks / s->stats->ts_tid);
seq_printf(seq, " %lu logged blocks per transaction\n",
- s->stats->u.run.rs_blocks_logged / s->stats->ts_tid);
+ s->stats->run.rs_blocks_logged / s->stats->ts_tid);
return 0;
}
return seq_release(inode, file);
}
-static struct file_operations jbd2_seq_info_fops = {
+static const struct file_operations jbd2_seq_info_fops = {
.owner = THIS_MODULE,
.open = jbd2_seq_info_open,
.read = seq_read,
{
journal->j_proc_entry = proc_mkdir(journal->j_devname, proc_jbd2_stats);
if (journal->j_proc_entry) {
- proc_create_data("history", S_IRUGO, journal->j_proc_entry,
- &jbd2_seq_history_fops, journal);
proc_create_data("info", S_IRUGO, journal->j_proc_entry,
&jbd2_seq_info_fops, journal);
}
static void jbd2_stats_proc_exit(journal_t *journal)
{
remove_proc_entry("info", journal->j_proc_entry);
- remove_proc_entry("history", journal->j_proc_entry);
remove_proc_entry(journal->j_devname, proc_jbd2_stats);
}
-static void journal_init_stats(journal_t *journal)
-{
- int size;
-
- if (!proc_jbd2_stats)
- return;
-
- journal->j_history_max = 100;
- size = sizeof(struct transaction_stats_s) * journal->j_history_max;
- journal->j_history = kzalloc(size, GFP_KERNEL);
- if (!journal->j_history) {
- journal->j_history_max = 0;
- return;
- }
- spin_lock_init(&journal->j_history_lock);
-}
-
/*
* Management for journal control blocks: functions to create and
* destroy journal_t structures, and to initialise and read existing
goto fail;
}
- journal_init_stats(journal);
+ spin_lock_init(&journal->j_history_lock);
return journal;
fail:
while ((p = strchr(p, '/')))
*p = '!';
p = journal->j_devname + strlen(journal->j_devname);
- sprintf(p, ":%lu", journal->j_inode->i_ino);
+ sprintf(p, "-%lu", journal->j_inode->i_ino);
jbd_debug(1,
"journal %p: inode %s/%ld, size %Ld, bits %d, blksize %ld\n",
journal, inode->i_sb->s_id, inode->i_ino,
rc = jfs_umount(sb);
if (rc)
jfs_err("jfs_umount failed with return code %d", rc);
- if (sbi->nls_tab)
- unload_nls(sbi->nls_tab);
- sbi->nls_tab = NULL;
+
+ unload_nls(sbi->nls_tab);
truncate_inode_pages(sbi->direct_inode->i_mapping, 0);
iput(sbi->direct_inode);
- sbi->direct_inode = NULL;
kfree(sbi);
if (nls_map != (void *) -1) {
/* Discard old (if remount) */
- if (sbi->nls_tab)
- unload_nls(sbi->nls_tab);
+ unload_nls(sbi->nls_tab);
sbi->nls_tab = nls_map;
}
return 1;
const void *from, size_t available)
{
loff_t pos = *ppos;
+ size_t ret;
+
if (pos < 0)
return -EINVAL;
- if (pos >= available)
+ if (pos >= available || !count)
return 0;
if (count > available - pos)
count = available - pos;
- if (copy_to_user(to, from + pos, count))
+ ret = copy_to_user(to, from + pos, count);
+ if (ret == count)
return -EFAULT;
+ count -= ret;
*ppos = pos + count;
return count;
}
if (copy_from_user(attr->set_buf, buf, size))
goto out;
- ret = len; /* claim we got the whole input */
attr->set_buf[size] = '\0';
val = simple_strtol(attr->set_buf, NULL, 0);
- attr->set(attr->data, val);
+ ret = attr->set(attr->data, val);
+ if (ret == 0)
+ ret = len; /* on success, claim we got the whole input */
out:
mutex_unlock(&attr->mutex);
return ret;
{
struct vfsmount *mnt;
- if (!type || !memchr(type, 0, PAGE_SIZE))
+ if (!type)
return -EINVAL;
/* we need capabilities... */
return 0;
}
+int copy_mount_string(const void __user *data, char **where)
+{
+ char *tmp;
+
+ if (!data) {
+ *where = NULL;
+ return 0;
+ }
+
+ tmp = strndup_user(data, PAGE_SIZE);
+ if (IS_ERR(tmp))
+ return PTR_ERR(tmp);
+
+ *where = tmp;
+ return 0;
+}
+
/*
* Flags is a 32-bit value that allows up to 31 non-fs dependent flags to
* be given to the mount() call (ie: read-only, no-dev, no-suid etc).
if (!dir_name || !*dir_name || !memchr(dir_name, 0, PAGE_SIZE))
return -EINVAL;
- if (dev_name && !memchr(dev_name, 0, PAGE_SIZE))
- return -EINVAL;
if (data_page)
((char *)data_page)[PAGE_SIZE - 1] = 0;
SYSCALL_DEFINE5(mount, char __user *, dev_name, char __user *, dir_name,
char __user *, type, unsigned long, flags, void __user *, data)
{
- int retval;
+ int ret;
+ char *kernel_type;
+ char *kernel_dir;
+ char *kernel_dev;
unsigned long data_page;
- unsigned long type_page;
- unsigned long dev_page;
- char *dir_page;
- retval = copy_mount_options(type, &type_page);
- if (retval < 0)
- return retval;
+ ret = copy_mount_string(type, &kernel_type);
+ if (ret < 0)
+ goto out_type;
- dir_page = getname(dir_name);
- retval = PTR_ERR(dir_page);
- if (IS_ERR(dir_page))
- goto out1;
+ kernel_dir = getname(dir_name);
+ if (IS_ERR(kernel_dir)) {
+ ret = PTR_ERR(kernel_dir);
+ goto out_dir;
+ }
- retval = copy_mount_options(dev_name, &dev_page);
- if (retval < 0)
- goto out2;
+ ret = copy_mount_string(dev_name, &kernel_dev);
+ if (ret < 0)
+ goto out_dev;
- retval = copy_mount_options(data, &data_page);
- if (retval < 0)
- goto out3;
+ ret = copy_mount_options(data, &data_page);
+ if (ret < 0)
+ goto out_data;
- retval = do_mount((char *)dev_page, dir_page, (char *)type_page,
- flags, (void *)data_page);
- free_page(data_page);
+ ret = do_mount(kernel_dev, kernel_dir, kernel_type, flags,
+ (void *) data_page);
-out3:
- free_page(dev_page);
-out2:
- putname(dir_page);
-out1:
- free_page(type_page);
- return retval;
+ free_page(data_page);
+out_data:
+ kfree(kernel_dev);
+out_dev:
+ putname(kernel_dir);
+out_dir:
+ kfree(kernel_type);
+out_type:
+ return ret;
}
/*
#ifdef CONFIG_NCPFS_NLS
/* unload the NLS charsets */
- if (server->nls_vol)
- {
- unload_nls(server->nls_vol);
- server->nls_vol = NULL;
- }
- if (server->nls_io)
- {
- unload_nls(server->nls_io);
- server->nls_io = NULL;
- }
+ unload_nls(server->nls_vol);
+ unload_nls(server->nls_io);
#endif /* CONFIG_NCPFS_NLS */
if (server->info_filp)
oldset_io = server->nls_io;
server->nls_io = iocharset;
- if (oldset_cp)
- unload_nls(oldset_cp);
- if (oldset_io)
- unload_nls(oldset_io);
+ unload_nls(oldset_cp);
+ unload_nls(oldset_io);
return 0;
}
return VM_FAULT_MAJOR;
}
-static struct vm_operations_struct ncp_file_mmap =
+static const struct vm_operations_struct ncp_file_mmap =
{
.fault = ncp_file_mmap_fault,
};
static int nfs_flock(struct file *filp, int cmd, struct file_lock *fl);
static int nfs_setlease(struct file *file, long arg, struct file_lock **fl);
-static struct vm_operations_struct nfs_file_vm_ops;
+static const struct vm_operations_struct nfs_file_vm_ops;
const struct file_operations nfs_file_operations = {
.llseek = nfs_file_llseek,
.direct_IO = nfs_direct_IO,
.migratepage = nfs_migrate_page,
.launder_page = nfs_launder_page,
+ .error_remove_page = generic_error_remove_page,
};
/*
return VM_FAULT_SIGBUS;
}
-static struct vm_operations_struct nfs_file_vm_ops = {
+static const struct vm_operations_struct nfs_file_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = nfs_vm_page_mkwrite,
};
*/
static int nfs_vmtruncate(struct inode * inode, loff_t offset)
{
- if (i_size_read(inode) < offset) {
- unsigned long limit;
-
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && offset > limit)
- goto out_sig;
- if (offset > inode->i_sb->s_maxbytes)
- goto out_big;
- spin_lock(&inode->i_lock);
- i_size_write(inode, offset);
- spin_unlock(&inode->i_lock);
- } else {
- struct address_space *mapping = inode->i_mapping;
+ loff_t oldsize;
+ int err;
- /*
- * truncation of in-use swapfiles is disallowed - it would
- * cause subsequent swapout to scribble on the now-freed
- * blocks.
- */
- if (IS_SWAPFILE(inode))
- return -ETXTBSY;
- spin_lock(&inode->i_lock);
- i_size_write(inode, offset);
- spin_unlock(&inode->i_lock);
+ err = inode_newsize_ok(inode, offset);
+ if (err)
+ goto out;
- /*
- * unmap_mapping_range is called twice, first simply for
- * efficiency so that truncate_inode_pages does fewer
- * single-page unmaps. However after this first call, and
- * before truncate_inode_pages finishes, it is possible for
- * private pages to be COWed, which remain after
- * truncate_inode_pages finishes, hence the second
- * unmap_mapping_range call must be made for correctness.
- */
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- truncate_inode_pages(mapping, offset);
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- }
- return 0;
-out_sig:
- send_sig(SIGXFSZ, current, 0);
-out_big:
- return -EFBIG;
+ spin_lock(&inode->i_lock);
+ oldsize = inode->i_size;
+ i_size_write(inode, offset);
+ spin_unlock(&inode->i_lock);
+
+ truncate_pagecache(inode, oldsize, offset);
+out:
+ return err;
}
/**
if (!(data->flags & NFS_MOUNT_TCP))
args->nfs_server.protocol = XPRT_TRANSPORT_UDP;
+ else
+ args->nfs_server.protocol = XPRT_TRANSPORT_TCP;
/* N.B. caller will free nfs_server.hostname in all cases */
args->nfs_server.hostname = kstrdup(data->hostname, GFP_KERNEL);
args->namlen = data->namlen;
extern int nfsd_pool_stats_open(struct inode *inode, struct file *file);
extern int nfsd_pool_stats_release(struct inode *inode, struct file *file);
-static struct file_operations pool_stats_operations = {
+static const struct file_operations pool_stats_operations = {
.open = nfsd_pool_stats_open,
.read = seq_read,
.llseek = seq_lseek,
void nilfs_btnode_cache_init_once(struct address_space *btnc)
{
+ memset(btnc, 0, sizeof(*btnc));
INIT_RADIX_TREE(&btnc->page_tree, GFP_ATOMIC);
spin_lock_init(&btnc->tree_lock);
INIT_LIST_HEAD(&btnc->private_list);
return 0;
}
-struct file_operations nilfs_dir_operations = {
+const struct file_operations nilfs_dir_operations = {
.llseek = generic_file_llseek,
.read = generic_read_dir,
.readdir = nilfs_readdir,
return 0;
}
-struct vm_operations_struct nilfs_file_vm_ops = {
+static const struct vm_operations_struct nilfs_file_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = nilfs_page_mkwrite,
};
* We have mostly NULL's here: the current defaults are ok for
* the nilfs filesystem.
*/
-struct file_operations nilfs_file_operations = {
+const struct file_operations nilfs_file_operations = {
.llseek = generic_file_llseek,
.read = do_sync_read,
.write = do_sync_write,
ii->i_dir_acl = S_ISREG(inode->i_mode) ?
0 : le32_to_cpu(raw_inode->i_dir_acl);
#endif
+ ii->i_dir_start_lookup = 0;
ii->i_cno = 0;
inode->i_generation = le32_to_cpu(raw_inode->i_generation);
};
static const struct inode_operations def_mdt_iops;
-static struct file_operations def_mdt_fops;
+static const struct file_operations def_mdt_fops;
/*
* NILFS2 uses pseudo inodes for meta data files such as DAT, cpfile, sufile,
/*
* Inodes and files operations
*/
-extern struct file_operations nilfs_dir_operations;
+extern const struct file_operations nilfs_dir_operations;
extern const struct inode_operations nilfs_file_inode_operations;
-extern struct file_operations nilfs_file_operations;
+extern const struct file_operations nilfs_file_operations;
extern const struct address_space_operations nilfs_aops;
extern const struct inode_operations nilfs_dir_inode_operations;
extern const struct inode_operations nilfs_special_inode_operations;
while (*s && len > 0) {
if (*s & 0x80) {
size = utf8_to_utf32(s, len, &u);
- if (size < 0) {
- /* Ignore character and move on */
- size = 1;
- } else if (u >= PLANE_SIZE) {
+ if (size < 0)
+ return -EINVAL;
+
+ if (u >= PLANE_SIZE) {
u -= PLANE_SIZE;
*op++ = (wchar_t) (SURROGATE_PAIR |
((u >> 10) & SURROGATE_BITS));
void unload_nls(struct nls_table *nls)
{
- module_put(nls->owner);
+ if (nls)
+ module_put(nls->owner);
}
static const wchar_t charset2uni[256] = {
.migratepage = buffer_migrate_page, /* Move a page cache page from
one physical page to an
other. */
+ .error_remove_page = generic_error_remove_page,
};
/**
.migratepage = buffer_migrate_page, /* Move a page cache page from
one physical page to an
other. */
+ .error_remove_page = generic_error_remove_page,
};
#ifdef NTFS_RW
v, old_nls->charset);
nls_map = old_nls;
} else /* nls_map */ {
- if (old_nls)
- unload_nls(old_nls);
+ unload_nls(old_nls);
}
} else if (!strcmp(p, "utf8")) {
bool val = false;
ntfs_free(vol->upcase);
vol->upcase = NULL;
}
- if (vol->nls_map) {
- unload_nls(vol->nls_map);
- vol->nls_map = NULL;
- }
+
+ unload_nls(vol->nls_map);
+
sb->s_fs_info = NULL;
kfree(vol);
.releasepage = ocfs2_releasepage,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
}
#endif /* CONFIG_DEBUG_FS */
-static struct file_operations o2hb_debug_fops = {
+static const struct file_operations o2hb_debug_fops = {
.open = o2hb_debug_open,
.release = o2hb_debug_release,
.read = o2hb_debug_read,
return seq_release_private(inode, file);
}
-static struct file_operations nst_seq_fops = {
+static const struct file_operations nst_seq_fops = {
.open = nst_fop_open,
.read = seq_read,
.llseek = seq_lseek,
return seq_release_private(inode, file);
}
-static struct file_operations sc_seq_fops = {
+static const struct file_operations sc_seq_fops = {
.open = sc_fop_open,
.read = seq_read,
.llseek = seq_lseek,
return -ENOMEM;
}
-static struct file_operations debug_purgelist_fops = {
+static const struct file_operations debug_purgelist_fops = {
.open = debug_purgelist_open,
.release = debug_buffer_release,
.read = debug_buffer_read,
return -ENOMEM;
}
-static struct file_operations debug_mle_fops = {
+static const struct file_operations debug_mle_fops = {
.open = debug_mle_open,
.release = debug_buffer_release,
.read = debug_buffer_read,
return seq_release_private(inode, file);
}
-static struct file_operations debug_lockres_fops = {
+static const struct file_operations debug_lockres_fops = {
.open = debug_lockres_open,
.release = debug_lockres_release,
.read = seq_read,
return -ENOMEM;
}
-static struct file_operations debug_state_fops = {
+static const struct file_operations debug_state_fops = {
.open = debug_state_open,
.release = debug_buffer_release,
.read = debug_buffer_read,
return ret;
}
-static struct vm_operations_struct ocfs2_file_vm_ops = {
+static const struct vm_operations_struct ocfs2_file_vm_ops = {
.fault = ocfs2_fault,
.page_mkwrite = ocfs2_page_mkwrite,
};
}
#endif /* CONFIG_DEBUG_FS */
-static struct file_operations ocfs2_osb_debug_fops = {
+static const struct file_operations ocfs2_osb_debug_fops = {
.open = ocfs2_osb_debug_open,
.release = ocfs2_debug_release,
.read = ocfs2_debug_read,
.rmdir = omfs_rmdir,
};
-struct file_operations omfs_dir_operations = {
+const struct file_operations omfs_dir_operations = {
.read = generic_read_dir,
.readdir = omfs_readdir,
.llseek = generic_file_llseek,
return generic_block_bmap(mapping, block, omfs_get_block);
}
-struct file_operations omfs_file_operations = {
+const struct file_operations omfs_file_operations = {
.llseek = generic_file_llseek,
.read = do_sync_read,
.write = do_sync_write,
extern int omfs_clear_range(struct super_block *sb, u64 block, int count);
/* dir.c */
-extern struct file_operations omfs_dir_operations;
+extern const struct file_operations omfs_dir_operations;
extern const struct inode_operations omfs_dir_inops;
extern int omfs_make_empty(struct inode *inode, struct super_block *sb);
extern int omfs_is_bad(struct omfs_sb_info *sbi, struct omfs_header *header,
u64 fsblock);
/* file.c */
-extern struct file_operations omfs_file_operations;
+extern const struct file_operations omfs_file_operations;
extern const struct inode_operations omfs_file_inops;
extern const struct address_space_operations omfs_aops;
extern void omfs_make_empty_table(struct buffer_head *bh, int offset);
part_stat_read(p, merges[WRITE]),
(unsigned long long)part_stat_read(p, sectors[WRITE]),
jiffies_to_msecs(part_stat_read(p, ticks[WRITE])),
- part_in_flight(p),
+ p->in_flight,
jiffies_to_msecs(part_stat_read(p, io_ticks)),
jiffies_to_msecs(part_stat_read(p, time_in_queue)));
}
-ssize_t part_inflight_show(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct hd_struct *p = dev_to_part(dev);
-
- return sprintf(buf, "%8u %8u\n", p->in_flight[0], p->in_flight[1]);
-}
-
#ifdef CONFIG_FAIL_MAKE_REQUEST
ssize_t part_fail_show(struct device *dev,
struct device_attribute *attr, char *buf)
static DEVICE_ATTR(size, S_IRUGO, part_size_show, NULL);
static DEVICE_ATTR(alignment_offset, S_IRUGO, part_alignment_offset_show, NULL);
static DEVICE_ATTR(stat, S_IRUGO, part_stat_show, NULL);
-static DEVICE_ATTR(inflight, S_IRUGO, part_inflight_show, NULL);
#ifdef CONFIG_FAIL_MAKE_REQUEST
static struct device_attribute dev_attr_fail =
__ATTR(make-it-fail, S_IRUGO|S_IWUSR, part_fail_show, part_fail_store);
&dev_attr_size.attr,
&dev_attr_alignment_offset.attr,
&dev_attr_stat.attr,
- &dev_attr_inflight.attr,
#ifdef CONFIG_FAIL_MAKE_REQUEST
&dev_attr_fail.attr,
#endif
p->nivcsw);
}
+#ifdef CONFIG_MMU
+
struct stack_stats {
struct vm_area_struct *vma;
unsigned long startpage;
mmput(mm);
}
}
+#else
+static void task_show_stack_usage(struct seq_file *m, struct task_struct *task)
+{
+}
+#endif /* CONFIG_MMU */
int proc_pid_status(struct seq_file *m, struct pid_namespace *ns,
struct pid *pid, struct task_struct *task)
"Committed_AS: %8lu kB\n"
"VmallocTotal: %8lu kB\n"
"VmallocUsed: %8lu kB\n"
- "VmallocChunk: %8lu kB\n",
+ "VmallocChunk: %8lu kB\n"
+#ifdef CONFIG_MEMORY_FAILURE
+ "HardwareCorrupted: %8lu kB\n"
+#endif
+ ,
K(i.totalram),
K(i.freeram),
K(i.bufferram),
(unsigned long)VMALLOC_TOTAL >> 10,
vmi.used >> 10,
vmi.largest_chunk >> 10
+#ifdef CONFIG_MEMORY_FAILURE
+ ,atomic_long_read(&mce_bad_pages) << (PAGE_SHIFT - 10)
+#endif
);
hugetlb_report_meminfo(m);
/* careful: calling conventions are nasty here */
res = count;
- error = table->proc_handler(table, write, filp, buf, &res, ppos);
+ error = table->proc_handler(table, write, buf, &res, ppos);
if (!error)
error = res;
out:
#include <linux/sched.h>
#include <linux/seq_file.h>
#include <linux/time.h>
+#include <linux/kernel_stat.h>
#include <asm/cputime.h>
static int uptime_proc_show(struct seq_file *m, void *v)
{
struct timespec uptime;
struct timespec idle;
- cputime_t idletime = cputime_add(init_task.utime, init_task.stime);
+ int i;
+ cputime_t idletime = cputime_zero;
+
+ for_each_possible_cpu(i)
+ idletime = cputime64_add(idletime, kstat_cpu(i).cpustat.idle);
do_posix_clock_monotonic_gettime(&uptime);
monotonic_to_bootbased(&uptime);
/* make various checks */
order = get_order(newsize);
if (unlikely(order >= MAX_ORDER))
- goto too_big;
+ return -EFBIG;
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && newsize > limit)
- goto fsize_exceeded;
-
- if (newsize > inode->i_sb->s_maxbytes)
- goto too_big;
+ ret = inode_newsize_ok(inode, newsize);
+ if (ret)
+ return ret;
i_size_write(inode, newsize);
return 0;
- fsize_exceeded:
- send_sig(SIGXFSZ, current, 0);
- too_big:
- return -EFBIG;
-
- add_error:
+add_error:
while (loop < npages)
__free_page(pages + loop++);
return ret;
max = min(in_inode->i_sb->s_maxbytes, out_inode->i_sb->s_maxbytes);
pos = *ppos;
- retval = -EINVAL;
- if (unlikely(pos < 0))
- goto fput_out;
if (unlikely(pos + count > max)) {
retval = -EOVERFLOW;
if (pos >= max)
pos = (ROMFH_SIZE + len + 1 + ROMFH_PAD) & ROMFH_MASK;
root = romfs_iget(sb, pos);
- if (!root)
+ if (IS_ERR(root))
goto error;
sb->s_root = d_alloc_root(root);
*/
#include <linux/kernel.h>
+#include <linux/sched.h>
#include <linux/syscalls.h>
#include <linux/module.h>
#include <linux/slab.h>
*/
int seq_path(struct seq_file *m, struct path *path, char *esc)
{
- if (m->count < m->size) {
- char *s = m->buf + m->count;
- char *p = d_path(path, s, m->size - m->count);
+ char *buf;
+ size_t size = seq_get_buf(m, &buf);
+ int res = -1;
+
+ if (size) {
+ char *p = d_path(path, buf, size);
if (!IS_ERR(p)) {
- s = mangle_path(s, p, esc);
- if (s) {
- p = m->buf + m->count;
- m->count = s - m->buf;
- return s - p;
- }
+ char *end = mangle_path(buf, p, esc);
+ if (end)
+ res = end - buf;
}
}
- m->count = m->size;
- return -1;
+ seq_commit(m, res);
+
+ return res;
}
EXPORT_SYMBOL(seq_path);
int seq_path_root(struct seq_file *m, struct path *path, struct path *root,
char *esc)
{
- int err = -ENAMETOOLONG;
- if (m->count < m->size) {
- char *s = m->buf + m->count;
+ char *buf;
+ size_t size = seq_get_buf(m, &buf);
+ int res = -ENAMETOOLONG;
+
+ if (size) {
char *p;
spin_lock(&dcache_lock);
- p = __d_path(path, root, s, m->size - m->count);
+ p = __d_path(path, root, buf, size);
spin_unlock(&dcache_lock);
- err = PTR_ERR(p);
+ res = PTR_ERR(p);
if (!IS_ERR(p)) {
- s = mangle_path(s, p, esc);
- if (s) {
- p = m->buf + m->count;
- m->count = s - m->buf;
- return 0;
- }
+ char *end = mangle_path(buf, p, esc);
+ if (end)
+ res = end - buf;
+ else
+ res = -ENAMETOOLONG;
}
}
- m->count = m->size;
- return err;
+ seq_commit(m, res);
+
+ return res < 0 ? res : 0;
}
/*
*/
int seq_dentry(struct seq_file *m, struct dentry *dentry, char *esc)
{
- if (m->count < m->size) {
- char *s = m->buf + m->count;
- char *p = dentry_path(dentry, s, m->size - m->count);
+ char *buf;
+ size_t size = seq_get_buf(m, &buf);
+ int res = -1;
+
+ if (size) {
+ char *p = dentry_path(dentry, buf, size);
if (!IS_ERR(p)) {
- s = mangle_path(s, p, esc);
- if (s) {
- p = m->buf + m->count;
- m->count = s - m->buf;
- return s - p;
- }
+ char *end = mangle_path(buf, p, esc);
+ if (end)
+ res = end - buf;
}
}
- m->count = m->size;
- return -1;
+ seq_commit(m, res);
+
+ return res;
}
int seq_bitmap(struct seq_file *m, const unsigned long *bits,
static void
smb_unload_nls(struct smb_sb_info *server)
{
- if (server->remote_nls) {
- unload_nls(server->remote_nls);
- server->remote_nls = NULL;
- }
- if (server->local_nls) {
- unload_nls(server->local_nls);
- server->local_nls = NULL;
- }
+ unload_nls(server->remote_nls);
+ unload_nls(server->local_nls);
}
static void
}
EXPORT_SYMBOL(get_super);
+
+/**
+ * get_active_super - get an active reference to the superblock of a device
+ * @bdev: device to get the superblock for
+ *
+ * Scans the superblock list and finds the superblock of the file system
+ * mounted on the device given. Returns the superblock with an active
+ * reference and s_umount held exclusively or %NULL if none was found.
+ */
+struct super_block *get_active_super(struct block_device *bdev)
+{
+ struct super_block *sb;
+
+ if (!bdev)
+ return NULL;
+
+ spin_lock(&sb_lock);
+ list_for_each_entry(sb, &super_blocks, s_list) {
+ if (sb->s_bdev != bdev)
+ continue;
+
+ sb->s_count++;
+ spin_unlock(&sb_lock);
+ down_write(&sb->s_umount);
+ if (sb->s_root) {
+ spin_lock(&sb_lock);
+ if (sb->s_count > S_BIAS) {
+ atomic_inc(&sb->s_active);
+ sb->s_count--;
+ spin_unlock(&sb_lock);
+ return sb;
+ }
+ spin_unlock(&sb_lock);
+ }
+ up_write(&sb->s_umount);
+ put_super(sb);
+ yield();
+ spin_lock(&sb_lock);
+ }
+ spin_unlock(&sb_lock);
+ return NULL;
+}
struct super_block * user_get_super(dev_t dev)
{
{
int retval;
int remount_rw;
-
+
+ if (sb->s_frozen != SB_UNFROZEN)
+ return -EBUSY;
+
#ifdef CONFIG_BLOCK
if (!(flags & MS_RDONLY) && bdev_read_only(sb->s_bdev))
return -EACCES;
#endif
+
if (flags & MS_RDONLY)
acct_auto_close(sb);
shrink_dcache_sb(sb);
* will protect the lockfs code from trying to start a snapshot
* while we are mounting
*/
- down(&bdev->bd_mount_sem);
+ mutex_lock(&bdev->bd_fsfreeze_mutex);
+ if (bdev->bd_fsfreeze_count > 0) {
+ mutex_unlock(&bdev->bd_fsfreeze_mutex);
+ error = -EBUSY;
+ goto error_bdev;
+ }
s = sget(fs_type, test_bdev_super, set_bdev_super, bdev);
- up(&bdev->bd_mount_sem);
+ mutex_unlock(&bdev->bd_fsfreeze_mutex);
if (IS_ERR(s))
goto error_s;
if (error)
goto out_sb;
+ /*
+ * filesystems should never set s_maxbytes larger than MAX_LFS_FILESIZE
+ * but s_maxbytes was an unsigned long long for many releases. Throw
+ * this warning for a little while to try and catch filesystems that
+ * violate this rule. This warning should be either removed or
+ * converted to a BUG() in 2.6.34.
+ */
+ WARN((mnt->mnt_sb->s_maxbytes < 0), "%s set sb->s_maxbytes to "
+ "negative value (%lld)\n", type->name, mnt->mnt_sb->s_maxbytes);
+
mnt->mnt_mountpoint = mnt->mnt_root;
mnt->mnt_parent = mnt;
up_write(&mnt->mnt_sb->s_umount);
struct mutex mutex;
void *buffer;
int mmapped;
- struct vm_operations_struct *vm_ops;
+ const struct vm_operations_struct *vm_ops;
struct file *file;
struct hlist_node list;
};
}
#endif
-static struct vm_operations_struct bin_vm_ops = {
+static const struct vm_operations_struct bin_vm_ops = {
.open = bin_vma_open,
.close = bin_vma_close,
.fault = bin_fault,
return err;
}
-static struct vm_operations_struct ubifs_file_vm_ops = {
+static const struct vm_operations_struct ubifs_file_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = ubifs_vm_page_mkwrite,
};
.direct_IO = xfs_vm_direct_IO,
.migratepage = buffer_migrate_page,
.is_partially_uptodate = block_is_partially_uptodate,
+ .error_remove_page = generic_error_remove_page,
};
#include <linux/dcache.h>
-static struct vm_operations_struct xfs_file_vm_ops;
+static const struct vm_operations_struct xfs_file_vm_ops;
STATIC ssize_t
xfs_file_aio_read(
.fsync = xfs_file_fsync,
};
-static struct vm_operations_struct xfs_file_vm_ops = {
+static const struct vm_operations_struct xfs_file_vm_ops = {
.fault = filemap_fault,
.page_mkwrite = xfs_vm_page_mkwrite,
};
xfs_stats_clear_proc_handler(
ctl_table *ctl,
int write,
- struct file *filp,
void __user *buffer,
size_t *lenp,
loff_t *ppos)
int c, ret, *valp = ctl->data;
__uint32_t vn_active;
- ret = proc_dointvec_minmax(ctl, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec_minmax(ctl, write, buffer, lenp, ppos);
if (!ret && write && *valp) {
printk("XFS Clearing xfsstats\n");
ACPI_BUS_TYPE_POWER,
ACPI_BUS_TYPE_PROCESSOR,
ACPI_BUS_TYPE_THERMAL,
- ACPI_BUS_TYPE_SYSTEM,
ACPI_BUS_TYPE_POWER_BUTTON,
ACPI_BUS_TYPE_SLEEP_BUTTON,
ACPI_BUS_DEVICE_TYPE_COUNT
struct acpi_device_flags {
u32 dynamic_status:1;
- u32 hardware_id:1;
- u32 compatible_ids:1;
u32 bus_address:1;
- u32 unique_id:1;
u32 removable:1;
u32 ejectable:1;
u32 lockable:1;
u32 performance_manageable:1;
u32 wake_capable:1; /* Wakeup(_PRW) supported? */
u32 force_power_state:1;
- u32 reserved:19;
+ u32 reserved:22;
};
/* File System */
typedef char acpi_device_name[40];
typedef char acpi_device_class[20];
+struct acpi_hardware_id {
+ struct list_head list;
+ char *id;
+};
+
struct acpi_device_pnp {
acpi_bus_id bus_id; /* Object name */
acpi_bus_address bus_address; /* _ADR */
- char *hardware_id; /* _HID */
- struct acpica_device_id_list *cid_list; /* _CIDs */
char *unique_id; /* _UID */
+ struct list_head ids; /* _HID and _CIDs */
acpi_device_name device_name; /* Driver-determined */
acpi_device_class device_class; /* " */
};
#define acpi_device_bid(d) ((d)->pnp.bus_id)
#define acpi_device_adr(d) ((d)->pnp.bus_address)
-#define acpi_device_hid(d) ((d)->pnp.hardware_id)
-#define acpi_device_uid(d) ((d)->pnp.unique_id)
+char *acpi_device_hid(struct acpi_device *device);
#define acpi_device_name(d) ((d)->pnp.device_name)
#define acpi_device_class(d) ((d)->pnp.device_class)
/* Device */
struct acpi_device {
- acpi_handle handle;
+ int device_type;
+ acpi_handle handle; /* no handle for fixed hardware */
struct acpi_device *parent;
struct list_head children;
struct list_head node;
int acpi_bus_get_device(acpi_handle handle, struct acpi_device **device);
void acpi_bus_data_handler(acpi_handle handle, void *context);
+acpi_status acpi_bus_get_status_handle(acpi_handle handle,
+ unsigned long long *sta);
int acpi_bus_get_status(struct acpi_device *device);
int acpi_bus_get_power(acpi_handle handle, int *state);
int acpi_bus_set_power(acpi_handle handle, int state);
--- /dev/null
+#ifndef ACPI_BUTTON_H
+#define ACPI_BUTTON_H
+
+#include <linux/notifier.h>
+
+#if defined(CONFIG_ACPI_BUTTON) || defined(CONFIG_ACPI_BUTTON_MODULE)
+extern int acpi_lid_notifier_register(struct notifier_block *nb);
+extern int acpi_lid_notifier_unregister(struct notifier_block *nb);
+extern int acpi_lid_open(void);
+#else
+static inline int acpi_lid_notifier_register(struct notifier_block *nb)
+{
+ return 0;
+}
+static inline int acpi_lid_notifier_unregister(struct notifier_block *nb)
+{
+ return 0;
+}
+static inline int acpi_lid_open(void)
+{
+ return 1;
+}
+#endif /* defined(CONFIG_ACPI_BUTTON) || defined(CONFIG_ACPI_BUTTON_MODULE) */
+
+#endif /* ACPI_BUTTON_H */
#define F_SETSIG 10 /* for sockets. */
#define F_GETSIG 11 /* for sockets. */
#endif
+#ifndef F_SETOWN_EX
+#define F_SETOWN_EX 12
+#define F_GETOWN_EX 13
+#endif
+
+#define F_OWNER_TID 0
+#define F_OWNER_PID 1
+#define F_OWNER_GID 2
+
+struct f_owner_ex {
+ int type;
+ pid_t pid;
+};
/* for F_[GET|SET]FL */
#define FD_CLOEXEC 1 /* actually anything with low bit set goes */
#ifndef _ASM_GENERIC_GPIO_H
#define _ASM_GENERIC_GPIO_H
+#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/errno.h>
#define MADV_REMOVE 9 /* remove these pages & resources */
#define MADV_DONTFORK 10 /* don't inherit across fork */
#define MADV_DOFORK 11 /* do inherit across fork */
+#define MADV_HWPOISON 100 /* poison a page for testing */
#define MADV_MERGEABLE 12 /* KSM may merge identical pages */
#define MADV_UNMERGEABLE 13 /* KSM may not merge identical pages */
#ifdef __ARCH_SI_TRAPNO
int _trapno; /* TRAP # which caused the signal */
#endif
+ short _addr_lsb; /* LSB of the reported address */
} _sigfault;
/* SIGPOLL */
#ifdef __ARCH_SI_TRAPNO
#define si_trapno _sifields._sigfault._trapno
#endif
+#define si_addr_lsb _sifields._sigfault._addr_lsb
#define si_band _sifields._sigpoll._band
#define si_fd _sifields._sigpoll._fd
#define BUS_ADRALN (__SI_FAULT|1) /* invalid address alignment */
#define BUS_ADRERR (__SI_FAULT|2) /* non-existant physical address */
#define BUS_OBJERR (__SI_FAULT|3) /* object specific hardware error */
-#define NSIGBUS 3
+/* hardware memory error consumed on a machine check: action required */
+#define BUS_MCEERR_AR (__SI_FAULT|4)
+/* hardware memory error detected in process but not consumed: action optional*/
+#define BUS_MCEERR_AO (__SI_FAULT|5)
+#define NSIGBUS 5
/*
* SIGTRAP si_codes
. = ALIGN(PAGE_SIZE); \
.data : AT(ADDR(.data) - LOAD_OFFSET) { \
INIT_TASK_DATA(inittask) \
+ NOSAVE_DATA \
+ PAGE_ALIGNED_DATA(pagealigned) \
CACHELINE_ALIGNED_DATA(cacheline) \
READ_MOSTLY_DATA(cacheline) \
DATA_DATA \
CONSTRUCTORS \
- NOSAVE_DATA \
- PAGE_ALIGNED_DATA(pagealigned) \
}
#define INIT_TEXT_SECTION(inittext_align) \
* @get_modes: get mode list for this connector
* @set_property: property for this connector may need update
* @destroy: make object go away
+ * @force: notify the driver the connector is forced on
*
* Each CRTC may have one or more connectors attached to it. The functions
* below allow the core DRM code to control connectors, enumerate available modes,
int (*set_property)(struct drm_connector *connector, struct drm_property *property,
uint64_t val);
void (*destroy)(struct drm_connector *connector);
+ void (*force)(struct drm_connector *connector);
};
struct drm_encoder_funcs {
void *helper_private;
};
+enum drm_connector_force {
+ DRM_FORCE_UNSPECIFIED,
+ DRM_FORCE_OFF,
+ DRM_FORCE_ON, /* force on analog part normally */
+ DRM_FORCE_ON_DIGITAL, /* for DVI-I use digital connector */
+};
+
/**
* drm_connector - central DRM connector control structure
* @crtc: CRTC this connector is currently connected to, NULL if none
void *helper_private;
+ /* forced on connector */
+ enum drm_connector_force force;
uint32_t encoder_ids[DRM_CONNECTOR_MAX_ENCODER];
uint32_t force_encoder_id;
struct drm_encoder *encoder; /* currently active encoder */
+ void *fb_helper_private;
};
/**
extern bool drm_detect_hdmi_monitor(struct edid *edid);
extern struct drm_display_mode *drm_cvt_mode(struct drm_device *dev,
int hdisplay, int vdisplay, int vrefresh,
- bool reduced, bool interlaced);
+ bool reduced, bool interlaced, bool margins);
extern struct drm_display_mode *drm_gtf_mode(struct drm_device *dev,
int hdisplay, int vdisplay, int vrefresh,
bool interlaced, int margins);
#include <linux/fb.h>
+#include "drm_fb_helper.h"
struct drm_crtc_helper_funcs {
/*
* Control power levels on the CRTC. If the mode passed in is
encoder->helper_private = (void *)funcs;
}
-static inline void drm_connector_helper_add(struct drm_connector *connector,
+static inline int drm_connector_helper_add(struct drm_connector *connector,
const struct drm_connector_helper_funcs *funcs)
{
connector->helper_private = (void *)funcs;
+ return drm_fb_helper_add_connector(connector);
}
extern int drm_helper_resume_force_mode(struct drm_device *dev);
struct drm_mode_set mode_set;
};
+
struct drm_fb_helper_funcs {
void (*gamma_set)(struct drm_crtc *crtc, u16 red, u16 green,
u16 blue, int regno);
};
+/* mode specified on the command line */
+struct drm_fb_helper_cmdline_mode {
+ bool specified;
+ bool refresh_specified;
+ bool bpp_specified;
+ int xres, yres;
+ int bpp;
+ int refresh;
+ bool rb;
+ bool interlace;
+ bool cvt;
+ bool margins;
+};
+
+struct drm_fb_helper_connector {
+ struct drm_fb_helper_cmdline_mode cmdline_mode;
+};
+
struct drm_fb_helper {
struct drm_framebuffer *fb;
struct drm_device *dev;
uint32_t fb_height,
uint32_t surface_width,
uint32_t surface_height,
+ uint32_t surface_depth,
+ uint32_t surface_bpp,
struct drm_framebuffer **fb_ptr));
int drm_fb_helper_init_crtc_count(struct drm_fb_helper *helper, int crtc_count,
int max_conn);
uint32_t fb_width, uint32_t fb_height);
void drm_fb_helper_fill_fix(struct fb_info *info, uint32_t pitch);
+int drm_fb_helper_add_connector(struct drm_connector *connector);
+int drm_fb_helper_parse_command_line(struct drm_device *dev);
+
#endif
{0x8086, 0x2e12, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
{0x8086, 0x2e22, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
{0x8086, 0x2e32, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
+ {0x8086, 0x2e42, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
{0x8086, 0xa001, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
{0x8086, 0xa011, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
{0x8086, 0x35e8, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_DISPLAY_VGA << 8, 0xffff00, 0}, \
#define DRM_I915_GEM_GET_APERTURE 0x23
#define DRM_I915_GEM_MMAP_GTT 0x24
#define DRM_I915_GET_PIPE_FROM_CRTC_ID 0x25
+#define DRM_I915_GEM_MADVISE 0x26
#define DRM_IOCTL_I915_INIT DRM_IOW( DRM_COMMAND_BASE + DRM_I915_INIT, drm_i915_init_t)
#define DRM_IOCTL_I915_FLUSH DRM_IO ( DRM_COMMAND_BASE + DRM_I915_FLUSH)
#define DRM_IOCTL_I915_GEM_GET_TILING DRM_IOWR (DRM_COMMAND_BASE + DRM_I915_GEM_GET_TILING, struct drm_i915_gem_get_tiling)
#define DRM_IOCTL_I915_GEM_GET_APERTURE DRM_IOR (DRM_COMMAND_BASE + DRM_I915_GEM_GET_APERTURE, struct drm_i915_gem_get_aperture)
#define DRM_IOCTL_I915_GET_PIPE_FROM_CRTC_ID DRM_IOWR(DRM_COMMAND_BASE + DRM_I915_GET_PIPE_FROM_CRTC_ID, struct drm_intel_get_pipe_from_crtc_id)
+#define DRM_IOCTL_I915_GEM_MADVISE DRM_IOWR(DRM_COMMAND_BASE + DRM_I915_GEM_MADVISE, struct drm_i915_gem_madvise)
/* Allow drivers to submit batchbuffers directly to hardware, relying
* on the security mechanisms provided by hardware.
__u32 pipe;
};
+#define I915_MADV_WILLNEED 0
+#define I915_MADV_DONTNEED 1
+#define __I915_MADV_PURGED 2 /* internal state */
+
+struct drm_i915_gem_madvise {
+ /** Handle of the buffer to change the backing store advice */
+ __u32 handle;
+
+ /* Advice: either the buffer will be needed again in the near future,
+ * or wont be and could be discarded under memory pressure.
+ */
+ __u32 madv;
+
+ /** Whether the backing store still exists. */
+ __u32 retained;
+};
+
#endif /* _I915_DRM_H_ */
int current_memory;
bool cant_use_aperture;
unsigned long page_mask;
- struct vm_operations_struct *vm_ops;
+ const struct vm_operations_struct *vm_ops;
};
/*
--- /dev/null
+/*
+ * include/linux/amba/mmci.h
+ */
+#ifndef AMBA_MMCI_H
+#define AMBA_MMCI_H
+
+#include <linux/mmc/host.h>
+
+struct mmci_platform_data {
+ unsigned int ocr_mask; /* available voltages */
+ u32 (*translate_vdd)(struct device *, unsigned int);
+ unsigned int (*status)(struct device *);
+ int gpio_wp;
+ int gpio_cd;
+ unsigned long capabilities;
+};
+
+#endif
/**
* enum SPI Clock Phase - clock phase (Motorola SPI interface only)
- * @SSP_CLK_RISING_EDGE: Receive data on rising edge
- * @SSP_CLK_FALLING_EDGE: Receive data on falling edge
+ * @SSP_CLK_FIRST_EDGE: Receive data on first edge transition (actual direction depends on polarity)
+ * @SSP_CLK_SECOND_EDGE: Receive data on second edge transition (actual direction depends on polarity)
*/
enum ssp_spi_clk_phase {
- SSP_CLK_RISING_EDGE,
- SSP_CLK_FALLING_EDGE
+ SSP_CLK_FIRST_EDGE,
+ SSP_CLK_SECOND_EDGE
};
/**
* array.
* @ASYNC_TX_ACK: immediately ack the descriptor, precludes setting up a
* dependency chain
- * @ASYNC_TX_DEP_ACK: ack the dependency descriptor. Useful for chaining.
+ * @ASYNC_TX_FENCE: specify that the next operation in the dependency
+ * chain uses this operation's result as an input
*/
enum async_tx_flags {
ASYNC_TX_XOR_ZERO_DST = (1 << 0),
ASYNC_TX_XOR_DROP_DST = (1 << 1),
- ASYNC_TX_ACK = (1 << 3),
- ASYNC_TX_DEP_ACK = (1 << 4),
+ ASYNC_TX_ACK = (1 << 2),
+ ASYNC_TX_FENCE = (1 << 3),
+};
+
+/**
+ * struct async_submit_ctl - async_tx submission/completion modifiers
+ * @flags: submission modifiers
+ * @depend_tx: parent dependency of the current operation being submitted
+ * @cb_fn: callback routine to run at operation completion
+ * @cb_param: parameter for the callback routine
+ * @scribble: caller provided space for dma/page address conversions
+ */
+struct async_submit_ctl {
+ enum async_tx_flags flags;
+ struct dma_async_tx_descriptor *depend_tx;
+ dma_async_tx_callback cb_fn;
+ void *cb_param;
+ void *scribble;
};
#ifdef CONFIG_DMA_ENGINE
#define async_tx_issue_pending_all dma_issue_pending_all
+
+/**
+ * async_tx_issue_pending - send pending descriptor to the hardware channel
+ * @tx: descriptor handle to retrieve hardware context
+ *
+ * Note: any dependent operations will have already been issued by
+ * async_tx_channel_switch, or (in the case of no channel switch) will
+ * be already pending on this channel.
+ */
+static inline void async_tx_issue_pending(struct dma_async_tx_descriptor *tx)
+{
+ if (likely(tx)) {
+ struct dma_chan *chan = tx->chan;
+ struct dma_device *dma = chan->device;
+
+ dma->device_issue_pending(chan);
+ }
+}
#ifdef CONFIG_ARCH_HAS_ASYNC_TX_FIND_CHANNEL
#include <asm/async_tx.h>
#else
#define async_tx_find_channel(dep, type, dst, dst_count, src, src_count, len) \
__async_tx_find_channel(dep, type)
struct dma_chan *
-__async_tx_find_channel(struct dma_async_tx_descriptor *depend_tx,
- enum dma_transaction_type tx_type);
+__async_tx_find_channel(struct async_submit_ctl *submit,
+ enum dma_transaction_type tx_type);
#endif /* CONFIG_ARCH_HAS_ASYNC_TX_FIND_CHANNEL */
#else
static inline void async_tx_issue_pending_all(void)
do { } while (0);
}
+static inline void async_tx_issue_pending(struct dma_async_tx_descriptor *tx)
+{
+ do { } while (0);
+}
+
static inline struct dma_chan *
-async_tx_find_channel(struct dma_async_tx_descriptor *depend_tx,
- enum dma_transaction_type tx_type, struct page **dst, int dst_count,
- struct page **src, int src_count, size_t len)
+async_tx_find_channel(struct async_submit_ctl *submit,
+ enum dma_transaction_type tx_type, struct page **dst,
+ int dst_count, struct page **src, int src_count,
+ size_t len)
{
return NULL;
}
* @cb_fn_param: parameter to pass to the callback routine
*/
static inline void
-async_tx_sync_epilog(dma_async_tx_callback cb_fn, void *cb_fn_param)
+async_tx_sync_epilog(struct async_submit_ctl *submit)
{
- if (cb_fn)
- cb_fn(cb_fn_param);
+ if (submit->cb_fn)
+ submit->cb_fn(submit->cb_param);
}
-void
-async_tx_submit(struct dma_chan *chan, struct dma_async_tx_descriptor *tx,
- enum async_tx_flags flags, struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_fn_param);
+typedef union {
+ unsigned long addr;
+ struct page *page;
+ dma_addr_t dma;
+} addr_conv_t;
+
+static inline void
+init_async_submit(struct async_submit_ctl *args, enum async_tx_flags flags,
+ struct dma_async_tx_descriptor *tx,
+ dma_async_tx_callback cb_fn, void *cb_param,
+ addr_conv_t *scribble)
+{
+ args->flags = flags;
+ args->depend_tx = tx;
+ args->cb_fn = cb_fn;
+ args->cb_param = cb_param;
+ args->scribble = scribble;
+}
+
+void async_tx_submit(struct dma_chan *chan, struct dma_async_tx_descriptor *tx,
+ struct async_submit_ctl *submit);
struct dma_async_tx_descriptor *
async_xor(struct page *dest, struct page **src_list, unsigned int offset,
- int src_cnt, size_t len, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_fn_param);
+ int src_cnt, size_t len, struct async_submit_ctl *submit);
struct dma_async_tx_descriptor *
-async_xor_zero_sum(struct page *dest, struct page **src_list,
- unsigned int offset, int src_cnt, size_t len,
- u32 *result, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_fn_param);
+async_xor_val(struct page *dest, struct page **src_list, unsigned int offset,
+ int src_cnt, size_t len, enum sum_check_flags *result,
+ struct async_submit_ctl *submit);
struct dma_async_tx_descriptor *
async_memcpy(struct page *dest, struct page *src, unsigned int dest_offset,
- unsigned int src_offset, size_t len, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_fn_param);
+ unsigned int src_offset, size_t len,
+ struct async_submit_ctl *submit);
struct dma_async_tx_descriptor *
async_memset(struct page *dest, int val, unsigned int offset,
- size_t len, enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_fn_param);
+ size_t len, struct async_submit_ctl *submit);
+
+struct dma_async_tx_descriptor *async_trigger_callback(struct async_submit_ctl *submit);
+
+struct dma_async_tx_descriptor *
+async_gen_syndrome(struct page **blocks, unsigned int offset, int src_cnt,
+ size_t len, struct async_submit_ctl *submit);
+
+struct dma_async_tx_descriptor *
+async_syndrome_val(struct page **blocks, unsigned int offset, int src_cnt,
+ size_t len, enum sum_check_flags *pqres, struct page *spare,
+ struct async_submit_ctl *submit);
+
+struct dma_async_tx_descriptor *
+async_raid6_2data_recov(int src_num, size_t bytes, int faila, int failb,
+ struct page **ptrs, struct async_submit_ctl *submit);
struct dma_async_tx_descriptor *
-async_trigger_callback(enum async_tx_flags flags,
- struct dma_async_tx_descriptor *depend_tx,
- dma_async_tx_callback cb_fn, void *cb_fn_param);
+async_raid6_datap_recov(int src_num, size_t bytes, int faila,
+ struct page **ptrs, struct async_submit_ctl *submit);
void async_tx_quiesce(struct dma_async_tx_descriptor **tx);
#endif /* _ASYNC_TX_H_ */
int (*getsockopt)(struct atm_vcc *vcc,int level,int optname,
void __user *optval,int optlen);
int (*setsockopt)(struct atm_vcc *vcc,int level,int optname,
- void __user *optval,int optlen);
+ void __user *optval,unsigned int optlen);
int (*send)(struct atm_vcc *vcc,struct sk_buff *skb);
int (*send_oam)(struct atm_vcc *vcc,void *cell,int flags);
void (*phy_put)(struct atm_dev *dev,unsigned char value,
const char *fmt, ...);
int bdi_register_dev(struct backing_dev_info *bdi, dev_t dev);
void bdi_unregister(struct backing_dev_info *bdi);
-void bdi_start_writeback(struct backing_dev_info *bdi, long nr_pages);
+void bdi_start_writeback(struct backing_dev_info *bdi, struct super_block *sb,
+ long nr_pages);
int bdi_writeback_task(struct bdi_writeback *wb);
int bdi_has_dirty_io(struct backing_dev_info *bdi);
* Any other use of the locks below is probably wrong.
*/
+enum backlight_update_reason {
+ BACKLIGHT_UPDATE_HOTKEY,
+ BACKLIGHT_UPDATE_SYSFS,
+};
+
struct backlight_device;
struct fb_info;
extern struct backlight_device *backlight_device_register(const char *name,
struct device *dev, void *devdata, struct backlight_ops *ops);
extern void backlight_device_unregister(struct backlight_device *bd);
+extern void backlight_force_update(struct backlight_device *bd,
+ enum backlight_update_reason reason);
#define to_backlight_device(obj) container_of(obj, struct backlight_device, dev)
extern int prepare_bprm_creds(struct linux_binprm *bprm);
extern void install_exec_creds(struct linux_binprm *bprm);
extern void do_coredump(long signr, int exit_code, struct pt_regs *regs);
-extern int set_binfmt(struct linux_binfmt *new);
+extern void set_binfmt(struct linux_binfmt *new);
extern void free_bprm(struct linux_binprm *);
#endif /* __KERNEL__ */
enum {
REQ_LB_OP_EJECT = 0x40, /* eject request */
REQ_LB_OP_FLUSH = 0x41, /* flush request */
- REQ_LB_OP_DISCARD = 0x42, /* discard sectors */
};
/*
typedef int (make_request_fn) (struct request_queue *q, struct bio *bio);
typedef int (prep_rq_fn) (struct request_queue *, struct request *);
typedef void (unplug_fn) (struct request_queue *);
-typedef int (prepare_discard_fn) (struct request_queue *, struct request *);
struct bio_vec;
struct bvec_merge_data {
unsigned int alignment_offset;
unsigned int io_min;
unsigned int io_opt;
+ unsigned int max_discard_sectors;
unsigned short logical_block_size;
unsigned short max_hw_segments;
make_request_fn *make_request_fn;
prep_rq_fn *prep_rq_fn;
unplug_fn *unplug_fn;
- prepare_discard_fn *prepare_discard_fn;
merge_bvec_fn *merge_bvec_fn;
prepare_flush_fn *prepare_flush_fn;
softirq_done_fn *softirq_done_fn;
#define QUEUE_FLAG_VIRT QUEUE_FLAG_NONROT /* paravirt device */
#define QUEUE_FLAG_IO_STAT 15 /* do IO stats */
#define QUEUE_FLAG_CQ 16 /* hardware does queuing */
+#define QUEUE_FLAG_DISCARD 17 /* supports DISCARD */
#define QUEUE_FLAG_DEFAULT ((1 << QUEUE_FLAG_IO_STAT) | \
(1 << QUEUE_FLAG_CLUSTER) | \
#define blk_queue_flushing(q) ((q)->ordseq)
#define blk_queue_stackable(q) \
test_bit(QUEUE_FLAG_STACKABLE, &(q)->queue_flags)
+#define blk_queue_discard(q) test_bit(QUEUE_FLAG_DISCARD, &(q)->queue_flags)
#define blk_fs_request(rq) ((rq)->cmd_type == REQ_TYPE_FS)
#define blk_pc_request(rq) ((rq)->cmd_type == REQ_TYPE_BLOCK_PC)
extern void blk_queue_max_phys_segments(struct request_queue *, unsigned short);
extern void blk_queue_max_hw_segments(struct request_queue *, unsigned short);
extern void blk_queue_max_segment_size(struct request_queue *, unsigned int);
+extern void blk_queue_max_discard_sectors(struct request_queue *q,
+ unsigned int max_discard_sectors);
extern void blk_queue_logical_block_size(struct request_queue *, unsigned short);
extern void blk_queue_physical_block_size(struct request_queue *, unsigned short);
extern void blk_queue_alignment_offset(struct request_queue *q,
extern void blk_queue_dma_alignment(struct request_queue *, int);
extern void blk_queue_update_dma_alignment(struct request_queue *, int);
extern void blk_queue_softirq_done(struct request_queue *, softirq_done_fn *);
-extern void blk_queue_set_discard(struct request_queue *, prepare_discard_fn *);
extern void blk_queue_rq_timed_out(struct request_queue *, rq_timed_out_fn *);
extern void blk_queue_rq_timeout(struct request_queue *, unsigned int);
extern struct backing_dev_info *blk_get_backing_dev_info(struct block_device *bdev);
return q->limits.physical_block_size;
}
+static inline int bdev_physical_block_size(struct block_device *bdev)
+{
+ return queue_physical_block_size(bdev_get_queue(bdev));
+}
+
static inline unsigned int queue_io_min(struct request_queue *q)
{
return q->limits.io_min;
}
+static inline int bdev_io_min(struct block_device *bdev)
+{
+ return queue_io_min(bdev_get_queue(bdev));
+}
+
static inline unsigned int queue_io_opt(struct request_queue *q)
{
return q->limits.io_opt;
}
+static inline int bdev_io_opt(struct block_device *bdev)
+{
+ return queue_io_opt(bdev_get_queue(bdev));
+}
+
static inline int queue_alignment_offset(struct request_queue *q)
{
- if (q && q->limits.misaligned)
+ if (q->limits.misaligned)
return -1;
- if (q && q->limits.alignment_offset)
- return q->limits.alignment_offset;
-
- return 0;
+ return q->limits.alignment_offset;
}
static inline int queue_sector_alignment_offset(struct request_queue *q,
& (q->limits.io_min - 1);
}
+static inline int bdev_alignment_offset(struct block_device *bdev)
+{
+ struct request_queue *q = bdev_get_queue(bdev);
+
+ if (q->limits.misaligned)
+ return -1;
+
+ if (bdev != bdev->bd_contains)
+ return bdev->bd_part->alignment_offset;
+
+ return q->limits.alignment_offset;
+}
+
static inline int queue_dma_alignment(struct request_queue *q)
{
return q ? q->dma_alignment : 511;
}
struct work_struct;
+struct delayed_work;
int kblockd_schedule_work(struct request_queue *q, struct work_struct *work);
+int kblockd_schedule_delayed_work(struct request_queue *q,
+ struct delayed_work *work,
+ unsigned long delay);
#define MODULE_ALIAS_BLOCKDEV(major,minor) \
MODULE_ALIAS("block-major-" __stringify(major) "-" __stringify(minor))
char __user *arg);
extern int blk_trace_startstop(struct request_queue *q, int start);
extern int blk_trace_remove(struct request_queue *q);
+extern void blk_trace_remove_sysfs(struct device *dev);
extern int blk_trace_init_sysfs(struct device *dev);
extern struct attribute_group blk_trace_attr_group;
# define blk_trace_startstop(q, start) (-ENOTTY)
# define blk_trace_remove(q) (-ENOTTY)
# define blk_add_trace_msg(q, fmt, ...) do { } while (0)
+# define blk_trace_remove_sysfs(dev) do { } while (0)
static inline int blk_trace_init_sysfs(struct device *dev)
{
return 0;
extern int cgroupstats_build(struct cgroupstats *stats,
struct dentry *dentry);
-extern struct file_operations proc_cgroup_operations;
+extern const struct file_operations proc_cgroup_operations;
/* Define the enumeration of all cgroup subsystems */
#define SUBSYS(_x) _x ## _subsys_id,
CGRP_WAIT_ON_RMDIR,
};
+/* which pidlist file are we talking about? */
+enum cgroup_filetype {
+ CGROUP_FILE_PROCS,
+ CGROUP_FILE_TASKS,
+};
+
+/*
+ * A pidlist is a list of pids that virtually represents the contents of one
+ * of the cgroup files ("procs" or "tasks"). We keep a list of such pidlists,
+ * a pair (one each for procs, tasks) for each pid namespace that's relevant
+ * to the cgroup.
+ */
+struct cgroup_pidlist {
+ /*
+ * used to find which pidlist is wanted. doesn't change as long as
+ * this particular list stays in the list.
+ */
+ struct { enum cgroup_filetype type; struct pid_namespace *ns; } key;
+ /* array of xids */
+ pid_t *list;
+ /* how many elements the above list has */
+ int length;
+ /* how many files are using the current array */
+ int use_count;
+ /* each of these stored in a list by its cgroup */
+ struct list_head links;
+ /* pointer to the cgroup we belong to, for list removal purposes */
+ struct cgroup *owner;
+ /* protects the other fields */
+ struct rw_semaphore mutex;
+};
+
struct cgroup {
unsigned long flags; /* "unsigned long" so bitops work */
*/
struct list_head release_list;
- /* pids_mutex protects pids_list and cached pid arrays. */
- struct rw_semaphore pids_mutex;
-
- /* Linked list of struct cgroup_pids */
- struct list_head pids_list;
+ /*
+ * list of pidlists, up to two for each namespace (one for procs, one
+ * for tasks); created on demand.
+ */
+ struct list_head pidlists;
+ struct mutex pidlist_mutex;
/* For RCU-protected deletion */
struct rcu_head rcu_head;
* during subsystem registration (at boot time).
*/
struct cgroup_subsys_state *subsys[CGROUP_SUBSYS_COUNT];
+
+ /* For RCU-protected deletion */
+ struct rcu_head rcu_head;
};
/*
struct cgroup *cgrp);
int (*pre_destroy)(struct cgroup_subsys *ss, struct cgroup *cgrp);
void (*destroy)(struct cgroup_subsys *ss, struct cgroup *cgrp);
- int (*can_attach)(struct cgroup_subsys *ss,
- struct cgroup *cgrp, struct task_struct *tsk);
+ int (*can_attach)(struct cgroup_subsys *ss, struct cgroup *cgrp,
+ struct task_struct *tsk, bool threadgroup);
void (*attach)(struct cgroup_subsys *ss, struct cgroup *cgrp,
- struct cgroup *old_cgrp, struct task_struct *tsk);
+ struct cgroup *old_cgrp, struct task_struct *tsk,
+ bool threadgroup);
void (*fork)(struct cgroup_subsys *ss, struct task_struct *task);
void (*exit)(struct cgroup_subsys *ss, struct task_struct *task);
int (*populate)(struct cgroup_subsys *ss,
*
* configfs Copyright (C) 2005 Oracle. All rights reserved.
*
- * Please read Documentation/filesystems/configfs.txt before using the
- * configfs interface, ESPECIALLY the parts about reference counts and
+ * Please read Documentation/filesystems/configfs/configfs.txt before using
+ * the configfs interface, ESPECIALLY the parts about reference counts and
* item destructors.
*/
};
struct cn_callback_data {
- void (*destruct_data) (void *);
- void *ddata;
-
- void *callback_priv;
- void (*callback) (struct cn_msg *);
+ struct sk_buff *skb;
+ void (*callback) (struct cn_msg *, struct netlink_skb_parms *);
void *free;
};
struct cn_queue_dev *cbdev;
};
-int cn_add_callback(struct cb_id *, char *, void (*callback) (struct cn_msg *));
+int cn_add_callback(struct cb_id *, char *, void (*callback) (struct cn_msg *, struct netlink_skb_parms *));
void cn_del_callback(struct cb_id *);
int cn_netlink_send(struct cn_msg *, u32, gfp_t);
-int cn_queue_add_callback(struct cn_queue_dev *dev, char *name, struct cb_id *id, void (*callback)(struct cn_msg *));
+int cn_queue_add_callback(struct cn_queue_dev *dev, char *name, struct cb_id *id, void (*callback)(struct cn_msg *, struct netlink_skb_parms *));
void cn_queue_del_callback(struct cn_queue_dev *dev, struct cb_id *id);
int queue_cn_work(struct cn_callback_entry *cbq, struct work_struct *work);
*/
#ifndef DCA_H
#define DCA_H
+
+#include <linux/pci.h>
+
/* DCA Provider API */
/* DCA Notifier Interface */
int id;
};
+struct dca_domain {
+ struct list_head node;
+ struct list_head dca_providers;
+ struct pci_bus *pci_rc;
+};
+
struct dca_ops {
int (*add_requester) (struct dca_provider *, struct device *);
int (*remove_requester) (struct dca_provider *, struct device *);
struct dca_provider *alloc_dca_provider(struct dca_ops *ops, int priv_size);
void free_dca_provider(struct dca_provider *dca);
int register_dca_provider(struct dca_provider *dca, struct device *dev);
-void unregister_dca_provider(struct dca_provider *dca);
+void unregister_dca_provider(struct dca_provider *dca, struct device *dev);
static inline void *dca_priv(struct dca_provider *dca)
{
* 2 as published by the Free Software Foundation.
*
* debugfs is for people to use instead of /proc or /sys.
- * See Documentation/DocBook/kernel-api for more details.
+ * See Documentation/DocBook/filesystems for more details.
*/
#ifndef _DEBUGFS_H_
/**
* enum dma_transaction_type - DMA transaction types/indexes
+ *
+ * Note: The DMA_ASYNC_TX capability is not to be set by drivers. It is
+ * automatically set as dma devices are registered.
*/
enum dma_transaction_type {
DMA_MEMCPY,
DMA_XOR,
- DMA_PQ_XOR,
- DMA_DUAL_XOR,
- DMA_PQ_UPDATE,
- DMA_ZERO_SUM,
- DMA_PQ_ZERO_SUM,
+ DMA_PQ,
+ DMA_XOR_VAL,
+ DMA_PQ_VAL,
DMA_MEMSET,
- DMA_MEMCPY_CRC32C,
DMA_INTERRUPT,
DMA_PRIVATE,
+ DMA_ASYNC_TX,
DMA_SLAVE,
};
/**
* enum dma_ctrl_flags - DMA flags to augment operation preparation,
- * control completion, and communicate status.
+ * control completion, and communicate status.
* @DMA_PREP_INTERRUPT - trigger an interrupt (callback) upon completion of
- * this transaction
+ * this transaction
* @DMA_CTRL_ACK - the descriptor cannot be reused until the client
- * acknowledges receipt, i.e. has has a chance to establish any
- * dependency chains
+ * acknowledges receipt, i.e. has has a chance to establish any dependency
+ * chains
* @DMA_COMPL_SKIP_SRC_UNMAP - set to disable dma-unmapping the source buffer(s)
* @DMA_COMPL_SKIP_DEST_UNMAP - set to disable dma-unmapping the destination(s)
* @DMA_COMPL_SRC_UNMAP_SINGLE - set to do the source dma-unmapping as single
* (if not set, do the source dma-unmapping as page)
* @DMA_COMPL_DEST_UNMAP_SINGLE - set to do the destination dma-unmapping as single
* (if not set, do the destination dma-unmapping as page)
+ * @DMA_PREP_PQ_DISABLE_P - prevent generation of P while generating Q
+ * @DMA_PREP_PQ_DISABLE_Q - prevent generation of Q while generating P
+ * @DMA_PREP_CONTINUE - indicate to a driver that it is reusing buffers as
+ * sources that were the result of a previous operation, in the case of a PQ
+ * operation it continues the calculation with new sources
+ * @DMA_PREP_FENCE - tell the driver that subsequent operations depend
+ * on the result of this operation
*/
enum dma_ctrl_flags {
DMA_PREP_INTERRUPT = (1 << 0),
DMA_COMPL_SKIP_DEST_UNMAP = (1 << 3),
DMA_COMPL_SRC_UNMAP_SINGLE = (1 << 4),
DMA_COMPL_DEST_UNMAP_SINGLE = (1 << 5),
+ DMA_PREP_PQ_DISABLE_P = (1 << 6),
+ DMA_PREP_PQ_DISABLE_Q = (1 << 7),
+ DMA_PREP_CONTINUE = (1 << 8),
+ DMA_PREP_FENCE = (1 << 9),
};
+/**
+ * enum sum_check_bits - bit position of pq_check_flags
+ */
+enum sum_check_bits {
+ SUM_CHECK_P = 0,
+ SUM_CHECK_Q = 1,
+};
+
+/**
+ * enum pq_check_flags - result of async_{xor,pq}_zero_sum operations
+ * @SUM_CHECK_P_RESULT - 1 if xor zero sum error, 0 otherwise
+ * @SUM_CHECK_Q_RESULT - 1 if reed-solomon zero sum error, 0 otherwise
+ */
+enum sum_check_flags {
+ SUM_CHECK_P_RESULT = (1 << SUM_CHECK_P),
+ SUM_CHECK_Q_RESULT = (1 << SUM_CHECK_Q),
+};
+
+
/**
* dma_cap_mask_t - capabilities bitmap modeled after cpumask_t.
* See linux/cpumask.h
* @flags: flags to augment operation preparation, control completion, and
* communicate status
* @phys: physical address of the descriptor
- * @tx_list: driver common field for operations that require multiple
- * descriptors
* @chan: target channel for this operation
* @tx_submit: set the prepared descriptor(s) to be executed by the engine
* @callback: routine to call after this operation is complete
dma_cookie_t cookie;
enum dma_ctrl_flags flags; /* not a 'long' to pack with cookie */
dma_addr_t phys;
- struct list_head tx_list;
struct dma_chan *chan;
dma_cookie_t (*tx_submit)(struct dma_async_tx_descriptor *tx);
dma_async_tx_callback callback;
* @global_node: list_head for global dma_device_list
* @cap_mask: one or more dma_capability flags
* @max_xor: maximum number of xor sources, 0 if no capability
+ * @max_pq: maximum number of PQ sources and PQ-continue capability
+ * @copy_align: alignment shift for memcpy operations
+ * @xor_align: alignment shift for xor operations
+ * @pq_align: alignment shift for pq operations
+ * @fill_align: alignment shift for memset operations
* @dev_id: unique device ID
* @dev: struct device reference for dma mapping api
* @device_alloc_chan_resources: allocate resources and return the
* @device_free_chan_resources: release DMA channel's resources
* @device_prep_dma_memcpy: prepares a memcpy operation
* @device_prep_dma_xor: prepares a xor operation
- * @device_prep_dma_zero_sum: prepares a zero_sum operation
+ * @device_prep_dma_xor_val: prepares a xor validation operation
+ * @device_prep_dma_pq: prepares a pq operation
+ * @device_prep_dma_pq_val: prepares a pqzero_sum operation
* @device_prep_dma_memset: prepares a memset operation
* @device_prep_dma_interrupt: prepares an end of chain interrupt operation
* @device_prep_slave_sg: prepares a slave dma operation
struct list_head channels;
struct list_head global_node;
dma_cap_mask_t cap_mask;
- int max_xor;
+ unsigned short max_xor;
+ unsigned short max_pq;
+ u8 copy_align;
+ u8 xor_align;
+ u8 pq_align;
+ u8 fill_align;
+ #define DMA_HAS_PQ_CONTINUE (1 << 15)
int dev_id;
struct device *dev;
struct dma_async_tx_descriptor *(*device_prep_dma_xor)(
struct dma_chan *chan, dma_addr_t dest, dma_addr_t *src,
unsigned int src_cnt, size_t len, unsigned long flags);
- struct dma_async_tx_descriptor *(*device_prep_dma_zero_sum)(
+ struct dma_async_tx_descriptor *(*device_prep_dma_xor_val)(
struct dma_chan *chan, dma_addr_t *src, unsigned int src_cnt,
- size_t len, u32 *result, unsigned long flags);
+ size_t len, enum sum_check_flags *result, unsigned long flags);
+ struct dma_async_tx_descriptor *(*device_prep_dma_pq)(
+ struct dma_chan *chan, dma_addr_t *dst, dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf,
+ size_t len, unsigned long flags);
+ struct dma_async_tx_descriptor *(*device_prep_dma_pq_val)(
+ struct dma_chan *chan, dma_addr_t *pq, dma_addr_t *src,
+ unsigned int src_cnt, const unsigned char *scf, size_t len,
+ enum sum_check_flags *pqres, unsigned long flags);
struct dma_async_tx_descriptor *(*device_prep_dma_memset)(
struct dma_chan *chan, dma_addr_t dest, int value, size_t len,
unsigned long flags);
void (*device_issue_pending)(struct dma_chan *chan);
};
+static inline bool dmaengine_check_align(u8 align, size_t off1, size_t off2, size_t len)
+{
+ size_t mask;
+
+ if (!align)
+ return true;
+ mask = (1 << align) - 1;
+ if (mask & (off1 | off2 | len))
+ return false;
+ return true;
+}
+
+static inline bool is_dma_copy_aligned(struct dma_device *dev, size_t off1,
+ size_t off2, size_t len)
+{
+ return dmaengine_check_align(dev->copy_align, off1, off2, len);
+}
+
+static inline bool is_dma_xor_aligned(struct dma_device *dev, size_t off1,
+ size_t off2, size_t len)
+{
+ return dmaengine_check_align(dev->xor_align, off1, off2, len);
+}
+
+static inline bool is_dma_pq_aligned(struct dma_device *dev, size_t off1,
+ size_t off2, size_t len)
+{
+ return dmaengine_check_align(dev->pq_align, off1, off2, len);
+}
+
+static inline bool is_dma_fill_aligned(struct dma_device *dev, size_t off1,
+ size_t off2, size_t len)
+{
+ return dmaengine_check_align(dev->fill_align, off1, off2, len);
+}
+
+static inline void
+dma_set_maxpq(struct dma_device *dma, int maxpq, int has_pq_continue)
+{
+ dma->max_pq = maxpq;
+ if (has_pq_continue)
+ dma->max_pq |= DMA_HAS_PQ_CONTINUE;
+}
+
+static inline bool dmaf_continue(enum dma_ctrl_flags flags)
+{
+ return (flags & DMA_PREP_CONTINUE) == DMA_PREP_CONTINUE;
+}
+
+static inline bool dmaf_p_disabled_continue(enum dma_ctrl_flags flags)
+{
+ enum dma_ctrl_flags mask = DMA_PREP_CONTINUE | DMA_PREP_PQ_DISABLE_P;
+
+ return (flags & mask) == mask;
+}
+
+static inline bool dma_dev_has_pq_continue(struct dma_device *dma)
+{
+ return (dma->max_pq & DMA_HAS_PQ_CONTINUE) == DMA_HAS_PQ_CONTINUE;
+}
+
+static unsigned short dma_dev_to_maxpq(struct dma_device *dma)
+{
+ return dma->max_pq & ~DMA_HAS_PQ_CONTINUE;
+}
+
+/* dma_maxpq - reduce maxpq in the face of continued operations
+ * @dma - dma device with PQ capability
+ * @flags - to check if DMA_PREP_CONTINUE and DMA_PREP_PQ_DISABLE_P are set
+ *
+ * When an engine does not support native continuation we need 3 extra
+ * source slots to reuse P and Q with the following coefficients:
+ * 1/ {00} * P : remove P from Q', but use it as a source for P'
+ * 2/ {01} * Q : use Q to continue Q' calculation
+ * 3/ {00} * Q : subtract Q from P' to cancel (2)
+ *
+ * In the case where P is disabled we only need 1 extra source:
+ * 1/ {01} * Q : use Q to continue Q' calculation
+ */
+static inline int dma_maxpq(struct dma_device *dma, enum dma_ctrl_flags flags)
+{
+ if (dma_dev_has_pq_continue(dma) || !dmaf_continue(flags))
+ return dma_dev_to_maxpq(dma);
+ else if (dmaf_p_disabled_continue(flags))
+ return dma_dev_to_maxpq(dma) - 1;
+ else if (dmaf_continue(flags))
+ return dma_dev_to_maxpq(dma) - 3;
+ BUG();
+}
+
/* --- public DMA engine API --- */
#ifdef CONFIG_DMA_ENGINE
#ifdef CONFIG_ASYNC_TX_DMA
#define async_dmaengine_get() dmaengine_get()
#define async_dmaengine_put() dmaengine_put()
+#ifdef CONFIG_ASYNC_TX_DISABLE_CHANNEL_SWITCH
+#define async_dma_find_channel(type) dma_find_channel(DMA_ASYNC_TX)
+#else
#define async_dma_find_channel(type) dma_find_channel(type)
+#endif /* CONFIG_ASYNC_TX_DISABLE_CHANNEL_SWITCH */
#else
static inline void async_dmaengine_get(void)
{
{
return NULL;
}
-#endif
+#endif /* CONFIG_ASYNC_TX_DMA */
dma_cookie_t dma_async_memcpy_buf_to_buf(struct dma_chan *chan,
void *dest, void *src, size_t len);
#define FB_ACCEL_NEOMAGIC_NM2230 96 /* NeoMagic NM2230 */
#define FB_ACCEL_NEOMAGIC_NM2360 97 /* NeoMagic NM2360 */
#define FB_ACCEL_NEOMAGIC_NM2380 98 /* NeoMagic NM2380 */
+#define FB_ACCEL_PXA3XX 99 /* PXA3xx */
#define FB_ACCEL_SAVAGE4 0x80 /* S3 Savage4 */
#define FB_ACCEL_SAVAGE3D 0x81 /* S3 Savage3D */
#define BLKTRACESTOP _IO(0x12,117)
#define BLKTRACETEARDOWN _IO(0x12,118)
#define BLKDISCARD _IO(0x12,119)
+#define BLKIOMIN _IO(0x12,120)
+#define BLKIOOPT _IO(0x12,121)
+#define BLKALIGNOFF _IO(0x12,122)
+#define BLKPBSZGET _IO(0x12,123)
#define BMAP_IOCTL 1 /* obsolete - kept for compatibility */
#define FIBMAP _IO(0x00,1) /* bmap access */
int (*launder_page) (struct page *);
int (*is_partially_uptodate) (struct page *, read_descriptor_t *,
unsigned long);
+ int (*error_remove_page)(struct address_space *, struct page *);
};
/*
struct super_block * bd_super;
int bd_openers;
struct mutex bd_mutex; /* open/close mutex */
- struct semaphore bd_mount_sem;
struct list_head bd_inodes;
void * bd_holder;
int bd_holders;
unsigned long s_blocksize;
unsigned char s_blocksize_bits;
unsigned char s_dirt;
- unsigned long long s_maxbytes; /* Max file size */
+ loff_t s_maxbytes; /* Max file size */
struct file_system_type *s_type;
const struct super_operations *s_op;
const struct dquot_operations *dq_op;
extern int inode_needs_sync(struct inode *inode);
extern void generic_delete_inode(struct inode *inode);
extern void generic_drop_inode(struct inode *inode);
+extern int generic_detach_inode(struct inode *inode);
extern struct inode *ilookup5_nowait(struct super_block *sb,
unsigned long hashval, int (*test)(struct inode *, void *),
extern void put_filesystem(struct file_system_type *fs);
extern struct file_system_type *get_fs_type(const char *name);
extern struct super_block *get_super(struct block_device *);
+extern struct super_block *get_active_super(struct block_device *bdev);
extern struct super_block *user_get_super(dev_t);
extern void drop_super(struct super_block *sb);
#define buffer_migrate_page NULL
#endif
-extern int inode_change_ok(struct inode *, struct iattr *);
+extern int inode_change_ok(const struct inode *, struct iattr *);
+extern int inode_newsize_ok(const struct inode *, loff_t offset);
extern int __must_check inode_setattr(struct inode *, struct iattr *);
extern void file_update_time(struct file *file);
__simple_attr_check_format(__fmt, 0ull); \
return simple_attr_open(inode, file, __get, __set, __fmt); \
} \
-static struct file_operations __fops = { \
+static const struct file_operations __fops = { \
.owner = THIS_MODULE, \
.open = __fops ## _open, \
.release = simple_attr_release, \
size_t len, loff_t *ppos);
struct ctl_table;
-int proc_nr_files(struct ctl_table *table, int write, struct file *filp,
+int proc_nr_files(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos);
int __init get_filesystem_list(char *buf);
extern int ftrace_enabled;
extern int
ftrace_enable_sysctl(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
typedef void (*ftrace_func_t)(unsigned long ip, unsigned long parent_ip);
extern int stack_tracer_enabled;
int
stack_trace_sysctl(struct ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
#endif
#include <linux/compiler.h>
#include <linux/types.h>
-struct inode;
-struct mm_struct;
-struct task_struct;
-union ktime;
-
/* Second argument to futex syscall */
#define FUTEX_BITSET_MATCH_ANY 0xffffffff
#ifdef __KERNEL__
+struct inode;
+struct mm_struct;
+struct task_struct;
+union ktime;
+
long do_futex(u32 __user *uaddr, int op, u32 val, union ktime *timeout,
u32 __user *uaddr2, u32 val2, u32 val3);
int make_it_fail;
#endif
unsigned long stamp;
- int in_flight[2];
+ int in_flight;
#ifdef CONFIG_SMP
struct disk_stats *dkstats;
#else
#define part_stat_sub(cpu, gendiskp, field, subnd) \
part_stat_add(cpu, gendiskp, field, -subnd)
-static inline void part_inc_in_flight(struct hd_struct *part, int rw)
+static inline void part_inc_in_flight(struct hd_struct *part)
{
- part->in_flight[rw]++;
+ part->in_flight++;
if (part->partno)
- part_to_disk(part)->part0.in_flight[rw]++;
+ part_to_disk(part)->part0.in_flight++;
}
-static inline void part_dec_in_flight(struct hd_struct *part, int rw)
+static inline void part_dec_in_flight(struct hd_struct *part)
{
- part->in_flight[rw]--;
+ part->in_flight--;
if (part->partno)
- part_to_disk(part)->part0.in_flight[rw]--;
-}
-
-static inline int part_in_flight(struct hd_struct *part)
-{
- return part->in_flight[0] + part->in_flight[1];
+ part_to_disk(part)->part0.in_flight--;
}
/* block/blk-core.c */
struct device_attribute *attr, char *buf);
extern ssize_t part_stat_show(struct device *dev,
struct device_attribute *attr, char *buf);
-extern ssize_t part_inflight_show(struct device *dev,
- struct device_attribute *attr, char *buf);
#ifdef CONFIG_FAIL_MAKE_REQUEST
extern ssize_t part_fail_show(struct device *dev,
struct device_attribute *attr, char *buf);
#include <linux/fs.h>
+struct ctl_table;
+struct user_struct;
+
#ifdef CONFIG_HUGETLB_PAGE
#include <linux/mempolicy.h>
#include <linux/shm.h>
#include <asm/tlbflush.h>
-struct ctl_table;
-struct user_struct;
-
int PageHuge(struct page *page);
static inline int is_vm_hugetlb_page(struct vm_area_struct *vma)
}
void reset_vma_resv_huge_pages(struct vm_area_struct *vma);
-int hugetlb_sysctl_handler(struct ctl_table *, int, struct file *, void __user *, size_t *, loff_t *);
-int hugetlb_overcommit_handler(struct ctl_table *, int, struct file *, void __user *, size_t *, loff_t *);
-int hugetlb_treat_movable_handler(struct ctl_table *, int, struct file *, void __user *, size_t *, loff_t *);
+int hugetlb_sysctl_handler(struct ctl_table *, int, void __user *, size_t *, loff_t *);
+int hugetlb_overcommit_handler(struct ctl_table *, int, void __user *, size_t *, loff_t *);
+int hugetlb_treat_movable_handler(struct ctl_table *, int, void __user *, size_t *, loff_t *);
int copy_hugetlb_page_range(struct mm_struct *, struct mm_struct *, struct vm_area_struct *);
int follow_hugetlb_page(struct mm_struct *, struct vm_area_struct *,
struct page **, struct vm_area_struct **,
}
extern const struct file_operations hugetlbfs_file_operations;
-extern struct vm_operations_struct hugetlb_vm_ops;
+extern const struct vm_operations_struct hugetlb_vm_ops;
struct file *hugetlb_file_setup(const char *name, size_t size, int acct,
struct user_struct **user, int creat_flags);
int hugetlb_get_quota(struct address_space *mapping, long delta);
#define is_file_hugepages(file) 0
#define set_file_hugepages(file) BUG()
-#define hugetlb_file_setup(name,size,acct,user,creat) ERR_PTR(-ENOSYS)
+static inline struct file *hugetlb_file_setup(const char *name, size_t size,
+ int acctflag, struct user_struct **user, int creat_flags)
+{
+ return ERR_PTR(-ENOSYS);
+}
#endif /* !CONFIG_HUGETLBFS */
__u16 flags;
__u16 __reserved;
__u32 datalen;
- __u32 rs_delay;
+ __u32 __reserved2;
/* data follows */
};
#define IPCCALL(version,op) ((version)<<16 | (op))
#ifdef __KERNEL__
-
-#include <linux/kref.h>
#include <linux/spinlock.h>
#define IPCMNI 32768 /* <= MAX_INT limit for ipc arrays (including sysctl changes) */
*/
struct transaction_chp_stats_s {
unsigned long cs_chp_time;
- unsigned long cs_forced_to_close;
- unsigned long cs_written;
- unsigned long cs_dropped;
+ __u32 cs_forced_to_close;
+ __u32 cs_written;
+ __u32 cs_dropped;
};
/* The transaction_t type is the guts of the journaling mechanism. It
unsigned long rs_flushing;
unsigned long rs_logging;
- unsigned long rs_handle_count;
- unsigned long rs_blocks;
- unsigned long rs_blocks_logged;
+ __u32 rs_handle_count;
+ __u32 rs_blocks;
+ __u32 rs_blocks_logged;
};
struct transaction_stats_s {
- int ts_type;
unsigned long ts_tid;
- union {
- struct transaction_run_stats_s run;
- struct transaction_chp_stats_s chp;
- } u;
+ struct transaction_run_stats_s run;
};
-#define JBD2_STATS_RUN 1
-#define JBD2_STATS_CHECKPOINT 2
-
static inline unsigned long
jbd2_time_diff(unsigned long start, unsigned long end)
{
/*
* Journal statistics
*/
- struct transaction_stats_s *j_history;
- int j_history_max;
- int j_history_cur;
- /*
- * Protect the transactions statistics history
- */
spinlock_t j_history_lock;
struct proc_dir_entry *j_proc_entry;
struct transaction_stats_s j_stats;
#define _KREF_H_
#include <linux/types.h>
-#include <asm/atomic.h>
struct kref {
atomic_t refcount;
extern bool mem_cgroup_oom_called(struct task_struct *task);
void mem_cgroup_update_mapped_file_stat(struct page *page, int val);
+unsigned long mem_cgroup_soft_limit_reclaim(struct zone *zone, int order,
+ gfp_t gfp_mask, int nid,
+ int zid);
#else /* CONFIG_CGROUP_MEM_RES_CTLR */
struct mem_cgroup;
{
}
+static inline
+unsigned long mem_cgroup_soft_limit_reclaim(struct zone *zone, int order,
+ gfp_t gfp_mask, int nid, int zid)
+{
+ return 0;
+}
+
#endif /* CONFIG_CGROUP_MEM_CONT */
#endif /* _LINUX_MEMCONTROL_H */
--- /dev/null
+/*
+ * include/linux/mfd/wm831x/status.h -- Status LEDs for WM831x
+ *
+ * Copyright 2009 Wolfson Microelectronics PLC.
+ *
+ * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#ifndef __MFD_WM831X_STATUS_H__
+#define __MFD_WM831X_STATUS_H__
+
+#define WM831X_LED_SRC_MASK 0xC000 /* LED_SRC - [15:14] */
+#define WM831X_LED_SRC_SHIFT 14 /* LED_SRC - [15:14] */
+#define WM831X_LED_SRC_WIDTH 2 /* LED_SRC - [15:14] */
+#define WM831X_LED_MODE_MASK 0x0300 /* LED_MODE - [9:8] */
+#define WM831X_LED_MODE_SHIFT 8 /* LED_MODE - [9:8] */
+#define WM831X_LED_MODE_WIDTH 2 /* LED_MODE - [9:8] */
+#define WM831X_LED_SEQ_LEN_MASK 0x0030 /* LED_SEQ_LEN - [5:4] */
+#define WM831X_LED_SEQ_LEN_SHIFT 4 /* LED_SEQ_LEN - [5:4] */
+#define WM831X_LED_SEQ_LEN_WIDTH 2 /* LED_SEQ_LEN - [5:4] */
+#define WM831X_LED_DUR_MASK 0x000C /* LED_DUR - [3:2] */
+#define WM831X_LED_DUR_SHIFT 2 /* LED_DUR - [3:2] */
+#define WM831X_LED_DUR_WIDTH 2 /* LED_DUR - [3:2] */
+#define WM831X_LED_DUTY_CYC_MASK 0x0003 /* LED_DUTY_CYC - [1:0] */
+#define WM831X_LED_DUTY_CYC_SHIFT 0 /* LED_DUTY_CYC - [1:0] */
+#define WM831X_LED_DUTY_CYC_WIDTH 2 /* LED_DUTY_CYC - [1:0] */
+
+#endif
#ifdef CONFIG_MMU
extern int is_vmalloc_or_module_addr(const void *x);
#else
-static int is_vmalloc_or_module_addr(const void *x)
+static inline int is_vmalloc_or_module_addr(const void *x)
{
return 0;
}
#define VM_FAULT_SIGBUS 0x0002
#define VM_FAULT_MAJOR 0x0004
#define VM_FAULT_WRITE 0x0008 /* Special case for get_user_pages */
+#define VM_FAULT_HWPOISON 0x0010 /* Hit poisoned page */
#define VM_FAULT_NOPAGE 0x0100 /* ->fault installed the pte, not return page */
#define VM_FAULT_LOCKED 0x0200 /* ->fault locked the returned page */
-#define VM_FAULT_ERROR (VM_FAULT_OOM | VM_FAULT_SIGBUS)
+#define VM_FAULT_ERROR (VM_FAULT_OOM | VM_FAULT_SIGBUS | VM_FAULT_HWPOISON)
/*
* Can be called by the pagefault handler when it gets a VM_FAULT_OOM.
unmap_mapping_range(mapping, holebegin, holelen, 0);
}
-extern int vmtruncate(struct inode * inode, loff_t offset);
-extern int vmtruncate_range(struct inode * inode, loff_t offset, loff_t end);
+extern void truncate_pagecache(struct inode *inode, loff_t old, loff_t new);
+extern int vmtruncate(struct inode *inode, loff_t offset);
+extern int vmtruncate_range(struct inode *inode, loff_t offset, loff_t end);
+
+int truncate_inode_page(struct address_space *mapping, struct page *page);
+int generic_error_remove_page(struct address_space *mapping, struct page *page);
+
+int invalidate_inode_page(struct page *page);
#ifdef CONFIG_MMU
extern int handle_mm_fault(struct mm_struct *mm, struct vm_area_struct *vma,
#define in_gate_area(task, addr) ({(void)task; in_gate_area_no_task(addr);})
#endif /* __HAVE_ARCH_GATE_AREA */
-int drop_caches_sysctl_handler(struct ctl_table *, int, struct file *,
+int drop_caches_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
unsigned long shrink_slab(unsigned long scanned, gfp_t gfp_mask,
unsigned long lru_pages);
extern int account_locked_memory(struct mm_struct *mm, struct rlimit *rlim,
size_t size);
extern void refund_locked_memory(struct mm_struct *mm, size_t size);
+
+extern void memory_failure(unsigned long pfn, int trapno);
+extern int __memory_failure(unsigned long pfn, int trapno, int ref);
+extern int sysctl_memory_failure_early_kill;
+extern int sysctl_memory_failure_recovery;
+extern atomic_long_t mce_bad_pages;
+
#endif /* __KERNEL__ */
#endif /* _LINUX_MM_H */
struct anon_vma *anon_vma; /* Serialized by page_table_lock */
/* Function pointers to deal with this struct. */
- struct vm_operations_struct * vm_ops;
+ const struct vm_operations_struct *vm_ops;
/* Information about our backing store: */
unsigned long vm_pgoff; /* Offset (within vm_file) in PAGE_SIZE
unsigned long saved_auxv[AT_VECTOR_SIZE]; /* for /proc/PID/auxv */
+ struct linux_binfmt *binfmt;
+
cpumask_t cpu_vm_mask;
/* Architecture-specific MM context */
unsigned long flags; /* Must use atomic bitops to access the bits */
struct core_state *core_state; /* coredumping support */
-
- /* aio bits */
+#ifdef CONFIG_AIO
spinlock_t ioctx_lock;
struct hlist_head ioctx_list;
-
+#endif
#ifdef CONFIG_MM_OWNER
/*
* "owner" points to a task that is regarded as the canonical
/* These two functions are used to setup the per zone pages min values */
struct ctl_table;
-struct file;
-int min_free_kbytes_sysctl_handler(struct ctl_table *, int, struct file *,
+int min_free_kbytes_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
extern int sysctl_lowmem_reserve_ratio[MAX_NR_ZONES-1];
-int lowmem_reserve_ratio_sysctl_handler(struct ctl_table *, int, struct file *,
+int lowmem_reserve_ratio_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-int percpu_pagelist_fraction_sysctl_handler(struct ctl_table *, int, struct file *,
+int percpu_pagelist_fraction_sysctl_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
int sysctl_min_unmapped_ratio_sysctl_handler(struct ctl_table *, int,
- struct file *, void __user *, size_t *, loff_t *);
+ void __user *, size_t *, loff_t *);
int sysctl_min_slab_ratio_sysctl_handler(struct ctl_table *, int,
- struct file *, void __user *, size_t *, loff_t *);
+ void __user *, size_t *, loff_t *);
extern int numa_zonelist_order_handler(struct ctl_table *, int,
- struct file *, void __user *, size_t *, loff_t *);
+ void __user *, size_t *, loff_t *);
extern char numa_zonelist_order[];
#define NUMA_ZONELIST_ORDER_LEN 16 /* string buffer size */
*/
#define MODULE_LICENSE(_license) MODULE_INFO(license, _license)
-/* Author, ideally of form NAME[, NAME]*[ and NAME] */
+/*
+ * Author(s), use "Name <email>" or just "Name", for multiple
+ * authors use multiple MODULE_AUTHOR() statements/lines.
+ */
#define MODULE_AUTHOR(_author) MODULE_INFO(author, _author)
/* What your module does. */
#endif
#ifdef CONFIG_KALLSYMS
- /* We keep the symbol and string tables for kallsyms. */
- Elf_Sym *symtab;
- unsigned int num_symtab;
- char *strtab;
+ /*
+ * We keep the symbol and string tables for kallsyms.
+ * The core_* fields below are temporary, loader-only (they
+ * could really be discarded after module init).
+ */
+ Elf_Sym *symtab, *core_symtab;
+ unsigned int num_symtab, core_num_syms;
+ char *strtab, *core_strtab;
/* Section attributes */
struct module_sect_attrs *sect_attrs;
#endif
#ifdef CONFIG_IP_MROUTE
-extern int ip_mroute_setsockopt(struct sock *, int, char __user *, int);
+extern int ip_mroute_setsockopt(struct sock *, int, char __user *, unsigned int);
extern int ip_mroute_getsockopt(struct sock *, int, char __user *, int __user *);
extern int ipmr_ioctl(struct sock *sk, int cmd, void __user *arg);
extern int ip_mr_init(void);
#else
static inline
int ip_mroute_setsockopt(struct sock *sock,
- int optname, char __user *optval, int optlen)
+ int optname, char __user *optval, unsigned int optlen)
{
return -ENOPROTOOPT;
}
struct sock;
#ifdef CONFIG_IPV6_MROUTE
-extern int ip6_mroute_setsockopt(struct sock *, int, char __user *, int);
+extern int ip6_mroute_setsockopt(struct sock *, int, char __user *, unsigned int);
extern int ip6_mroute_getsockopt(struct sock *, int, char __user *, int __user *);
extern int ip6_mr_input(struct sk_buff *skb);
extern int ip6mr_ioctl(struct sock *sk, int cmd, void __user *arg);
#else
static inline
int ip6_mroute_setsockopt(struct sock *sock,
- int optname, char __user *optval, int optlen)
+ int optname, char __user *optval, unsigned int optlen)
{
return -ENOPROTOOPT;
}
int (*listen) (struct socket *sock, int len);
int (*shutdown) (struct socket *sock, int flags);
int (*setsockopt)(struct socket *sock, int level,
- int optname, char __user *optval, int optlen);
+ int optname, char __user *optval, unsigned int optlen);
int (*getsockopt)(struct socket *sock, int level,
int optname, char __user *optval, int __user *optlen);
int (*compat_setsockopt)(struct socket *sock, int level,
- int optname, char __user *optval, int optlen);
+ int optname, char __user *optval, unsigned int optlen);
int (*compat_getsockopt)(struct socket *sock, int level,
int optname, char __user *optval, int __user *optlen);
int (*sendmsg) (struct kiocb *iocb, struct socket *sock,
extern int kernel_getsockopt(struct socket *sock, int level, int optname,
char *optval, int *optlen);
extern int kernel_setsockopt(struct socket *sock, int level, int optname,
- char *optval, int optlen);
+ char *optval, unsigned int optlen);
extern int kernel_sendpage(struct socket *sock, struct page *page, int offset,
size_t size, int flags);
extern int kernel_sock_ioctl(struct socket *sock, int cmd, unsigned long arg);
SOCKCALL_WRAP(name, listen, (struct socket *sock, int len), (sock, len)) \
SOCKCALL_WRAP(name, shutdown, (struct socket *sock, int flags), (sock, flags)) \
SOCKCALL_WRAP(name, setsockopt, (struct socket *sock, int level, int optname, \
- char __user *optval, int optlen), (sock, level, optname, optval, optlen)) \
+ char __user *optval, unsigned int optlen), (sock, level, optname, optval, optlen)) \
SOCKCALL_WRAP(name, getsockopt, (struct socket *sock, int level, int optname, \
char __user *optval, int __user *optlen), (sock, level, optname, optval, optlen)) \
SOCKCALL_WRAP(name, sendmsg, (struct kiocb *iocb, struct socket *sock, struct msghdr *m, size_t len), \
/* Call setsockopt() */
int nf_setsockopt(struct sock *sk, u_int8_t pf, int optval, char __user *opt,
- int len);
+ unsigned int len);
int nf_getsockopt(struct sock *sk, u_int8_t pf, int optval, char __user *opt,
int *len);
int compat_nf_setsockopt(struct sock *sk, u_int8_t pf, int optval,
- char __user *opt, int len);
+ char __user *opt, unsigned int len);
int compat_nf_getsockopt(struct sock *sk, u_int8_t pf, int optval,
char __user *opt, int *len);
extern void netlink_kernel_release(struct sock *sk);
extern int __netlink_change_ngroups(struct sock *sk, unsigned int groups);
extern int netlink_change_ngroups(struct sock *sk, unsigned int groups);
+extern void __netlink_clear_multicast_users(struct sock *sk, unsigned int group);
extern void netlink_clear_multicast_users(struct sock *sk, unsigned int group);
extern void netlink_ack(struct sk_buff *in_skb, struct nlmsghdr *nlh, int err);
extern int netlink_has_listeners(struct sock *sk, unsigned int group);
#ifdef __KERNEL__
#include <linux/in.h>
-#include <linux/kref.h>
#include <linux/mm.h>
#include <linux/pagemap.h>
#include <linux/rbtree.h>
* PG_buddy is set to indicate that the page is free and in the buddy system
* (see mm/page_alloc.c).
*
+ * PG_hwpoison indicates that a page got corrupted in hardware and contains
+ * data with incorrect ECC bits that triggered a machine check. Accessing is
+ * not safe since it may cause another machine check. Don't touch!
*/
/*
#endif
#ifdef CONFIG_ARCH_USES_PG_UNCACHED
PG_uncached, /* Page has been mapped as uncached */
+#endif
+#ifdef CONFIG_MEMORY_FAILURE
+ PG_hwpoison, /* hardware poisoned page. Don't touch */
#endif
__NR_PAGEFLAGS,
PAGEFLAG_FALSE(Uncached)
#endif
+#ifdef CONFIG_MEMORY_FAILURE
+PAGEFLAG(HWPoison, hwpoison)
+TESTSETFLAG(HWPoison, hwpoison)
+#define __PG_HWPOISON (1UL << PG_hwpoison)
+#else
+PAGEFLAG_FALSE(HWPoison)
+#define __PG_HWPOISON 0
+#endif
+
static inline int PageUptodate(struct page *page)
{
int ret = test_bit(PG_uptodate, &(page)->flags);
1 << PG_private | 1 << PG_private_2 | \
1 << PG_buddy | 1 << PG_writeback | 1 << PG_reserved | \
1 << PG_slab | 1 << PG_swapcache | 1 << PG_active | \
- 1 << PG_unevictable | __PG_MLOCKED)
+ 1 << PG_unevictable | __PG_MLOCKED | __PG_HWPOISON)
/*
* Flags checked when a page is prepped for return by the page allocator.
PCG_LOCK, /* page cgroup is locked */
PCG_CACHE, /* charged as cache */
PCG_USED, /* this object is in use. */
+ PCG_ACCT_LRU, /* page has been accounted for */
};
#define TESTPCGFLAG(uname, lname) \
static inline void ClearPageCgroup##uname(struct page_cgroup *pc) \
{ clear_bit(PCG_##lname, &pc->flags); }
+#define TESTCLEARPCGFLAG(uname, lname) \
+static inline int TestClearPageCgroup##uname(struct page_cgroup *pc) \
+ { return test_and_clear_bit(PCG_##lname, &pc->flags); }
+
/* Cache flag is set only once (at allocation) */
TESTPCGFLAG(Cache, CACHE)
+CLEARPCGFLAG(Cache, CACHE)
+SETPCGFLAG(Cache, CACHE)
TESTPCGFLAG(Used, USED)
CLEARPCGFLAG(Used, USED)
+SETPCGFLAG(Used, USED)
+
+SETPCGFLAG(AcctLRU, ACCT_LRU)
+CLEARPCGFLAG(AcctLRU, ACCT_LRU)
+TESTPCGFLAG(AcctLRU, ACCT_LRU)
+TESTCLEARPCGFLAG(AcctLRU, ACCT_LRU)
static inline int page_cgroup_nid(struct page_cgroup *pc)
{
#define PCI_DEVICE_ID_INTEL_E7525_MCH 0x359e
#define PCI_DEVICE_ID_INTEL_IOAT_CNB 0x360b
#define PCI_DEVICE_ID_INTEL_FBD_CNB 0x360c
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF0 0x3710
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF1 0x3711
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF2 0x3712
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF3 0x3713
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF4 0x3714
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF5 0x3715
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF6 0x3716
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF7 0x3717
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF8 0x3718
+#define PCI_DEVICE_ID_INTEL_IOAT_JSF9 0x3719
#define PCI_DEVICE_ID_INTEL_ICH10_0 0x3a14
#define PCI_DEVICE_ID_INTEL_ICH10_1 0x3a16
#define PCI_DEVICE_ID_INTEL_ICH10_2 0x3a18
* struct perf_event_header header;
* u32 pid, ppid;
* u32 tid, ptid;
- * { u64 time; } && PERF_SAMPLE_TIME
+ * u64 time;
* };
*/
PERF_EVENT_FORK = 7,
* struct perf_event_header header;
* u32 pid, ppid;
* u32 tid, ptid;
- * { u64 time; } && PERF_SAMPLE_TIME
+ * u64 time;
* };
*/
PERF_RECORD_FORK = 7,
#define PNPIPE_IFINDEX 2
#define PNADDR_ANY 0
+#define PNADDR_BROADCAST 0xFC
#define PNPORT_RESOURCE_ROUTING 0
/* Values for PNPIPE_ENCAP option */
#ifdef __KERNEL__
#include <linux/compiler.h>
+#include <linux/ktime.h>
#include <linux/wait.h>
#include <linux/string.h>
#include <linux/fs.h>
-#include <linux/sched.h>
#include <asm/uaccess.h>
/* ~832 bytes of stack space used max in sys_select/sys_poll before allocating
#define PR_TASK_PERF_EVENTS_DISABLE 31
#define PR_TASK_PERF_EVENTS_ENABLE 32
+#define PR_MCE_KILL 33
+
#endif /* _LINUX_PRCTL_H */
#endif
extern const struct file_operations ramfs_file_operations;
-extern struct vm_operations_struct generic_file_vm_ops;
+extern const struct vm_operations_struct generic_file_vm_ops;
extern int __init init_rootfs(void);
#endif
* cause relay_open() to create a single global buffer rather
* than the default set of per-cpu buffers.
*
- * See Documentation/filesystems/relayfs.txt for more info.
+ * See Documentation/filesystems/relay.txt for more info.
*/
struct dentry *(*create_buf_file)(const char *filename,
struct dentry *parent,
* the limit that usage cannot exceed
*/
unsigned long long limit;
+ /*
+ * the limit that usage can be exceed
+ */
+ unsigned long long soft_limit;
/*
* the number of unsuccessful attempts to consume the resource
*/
RES_MAX_USAGE,
RES_LIMIT,
RES_FAILCNT,
+ RES_SOFT_LIMIT,
};
/*
return false;
}
+static inline bool res_counter_soft_limit_check_locked(struct res_counter *cnt)
+{
+ if (cnt->usage < cnt->soft_limit)
+ return true;
+
+ return false;
+}
+
+/**
+ * Get the difference between the usage and the soft limit
+ * @cnt: The counter
+ *
+ * Returns 0 if usage is less than or equal to soft limit
+ * The difference between usage and soft limit, otherwise.
+ */
+static inline unsigned long long
+res_counter_soft_limit_excess(struct res_counter *cnt)
+{
+ unsigned long long excess;
+ unsigned long flags;
+
+ spin_lock_irqsave(&cnt->lock, flags);
+ if (cnt->usage <= cnt->soft_limit)
+ excess = 0;
+ else
+ excess = cnt->usage - cnt->soft_limit;
+ spin_unlock_irqrestore(&cnt->lock, flags);
+ return excess;
+}
+
/*
* Helper function to detect if the cgroup is within it's limit or
* not. It's currently called from cgroup_rss_prepare()
return ret;
}
+static inline bool res_counter_check_under_soft_limit(struct res_counter *cnt)
+{
+ bool ret;
+ unsigned long flags;
+
+ spin_lock_irqsave(&cnt->lock, flags);
+ ret = res_counter_soft_limit_check_locked(cnt);
+ spin_unlock_irqrestore(&cnt->lock, flags);
+ return ret;
+}
+
static inline void res_counter_reset_max(struct res_counter *cnt)
{
unsigned long flags;
return ret;
}
+static inline int
+res_counter_set_soft_limit(struct res_counter *cnt,
+ unsigned long long soft_limit)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&cnt->lock, flags);
+ cnt->soft_limit = soft_limit;
+ spin_unlock_irqrestore(&cnt->lock, flags);
+ return 0;
+}
+
#endif
*/
int page_referenced(struct page *, int is_locked,
struct mem_cgroup *cnt, unsigned long *vm_flags);
-int try_to_unmap(struct page *, int ignore_refs);
+enum ttu_flags {
+ TTU_UNMAP = 0, /* unmap mode */
+ TTU_MIGRATION = 1, /* migration mode */
+ TTU_MUNLOCK = 2, /* munlock mode */
+ TTU_ACTION_MASK = 0xff,
+
+ TTU_IGNORE_MLOCK = (1 << 8), /* ignore mlock */
+ TTU_IGNORE_ACCESS = (1 << 9), /* don't age */
+ TTU_IGNORE_HWPOISON = (1 << 10),/* corrupted page is recoverable */
+};
+#define TTU_ACTION(x) ((x) & TTU_ACTION_MASK)
+
+int try_to_unmap(struct page *, enum ttu_flags flags);
/*
* Called from mm/filemap_xip.c to unmap empty zero page
*/
int try_to_munlock(struct page *);
+/*
+ * Called by memory-failure.c to kill processes.
+ */
+struct anon_vma *page_lock_anon_vma(struct page *page);
+void page_unlock_anon_vma(struct anon_vma *anon_vma);
+int page_mapped_in_vma(struct page *page, struct vm_area_struct *vma);
+
#else /* !CONFIG_MMU */
#define anon_vma_init() do {} while (0)
extern void touch_softlockup_watchdog(void);
extern void touch_all_softlockup_watchdogs(void);
extern int proc_dosoftlockup_thresh(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos);
extern unsigned int softlockup_panic;
extern int softlockup_thresh;
extern unsigned long sysctl_hung_task_timeout_secs;
extern unsigned long sysctl_hung_task_warnings;
extern int proc_dohung_task_timeout_secs(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos);
#endif
struct mm_struct *mm, *active_mm;
/* task state */
- struct linux_binfmt *binfmt;
int exit_state;
int exit_code, exit_signal;
int pdeath_signal; /* The signal sent when the parent dies */
#define PF_EXITPIDONE 0x00000008 /* pi exit done on shut down */
#define PF_VCPU 0x00000010 /* I'm a virtual CPU */
#define PF_FORKNOEXEC 0x00000040 /* forked but didn't exec */
+#define PF_MCE_PROCESS 0x00000080 /* process policy on mce errors */
#define PF_SUPERPRIV 0x00000100 /* used super-user privileges */
#define PF_DUMPCORE 0x00000200 /* dumped core */
#define PF_SIGNALED 0x00000400 /* killed by a signal */
#define PF_SPREAD_PAGE 0x01000000 /* Spread page cache over cpuset */
#define PF_SPREAD_SLAB 0x02000000 /* Spread some slab caches over cpuset */
#define PF_THREAD_BOUND 0x04000000 /* Thread bound to specific cpu */
+#define PF_MCE_EARLY 0x08000000 /* Early kill for mce process policy */
#define PF_MEMPOLICY 0x10000000 /* Non-default NUMA mempolicy */
#define PF_MUTEX_TESTER 0x20000000 /* Thread belongs to the rt mutex tester */
#define PF_FREEZER_SKIP 0x40000000 /* Freezer should not count it as freezeable */
extern unsigned int sysctl_timer_migration;
int sched_nr_latency_handler(struct ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length,
+ void __user *buffer, size_t *length,
loff_t *ppos);
#endif
#ifdef CONFIG_SCHED_DEBUG
extern int sysctl_sched_rt_runtime;
int sched_rt_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
extern unsigned int sysctl_sched_compat_yield;
extern int kill_pid(struct pid *pid, int sig, int priv);
extern int kill_proc_info(int, struct siginfo *, pid_t);
extern int do_notify_parent(struct task_struct *, int);
+extern void __wake_up_parent(struct task_struct *p, struct task_struct *parent);
extern void force_sig(int, struct task_struct *);
extern void force_sig_specific(int, struct task_struct *);
extern int send_sig(int, struct task_struct *, int);
return unlikely(test_tsk_thread_flag(p,TIF_SIGPENDING));
}
-extern int __fatal_signal_pending(struct task_struct *p);
+static inline int __fatal_signal_pending(struct task_struct *p)
+{
+ return unlikely(sigismember(&p->pending.signal, SIGKILL));
+}
static inline int fatal_signal_pending(struct task_struct *p)
{
return PAGE_ALIGN(mmap_min_addr);
return hint;
}
-extern int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp,
+extern int mmap_min_addr_handler(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos);
#ifdef CONFIG_SECURITY
#define SEQ_SKIP 1
+/**
+ * seq_get_buf - get buffer to write arbitrary data to
+ * @m: the seq_file handle
+ * @bufp: the beginning of the buffer is stored here
+ *
+ * Return the number of bytes available in the buffer, or zero if
+ * there's no space.
+ */
+static inline size_t seq_get_buf(struct seq_file *m, char **bufp)
+{
+ BUG_ON(m->count > m->size);
+ if (m->count < m->size)
+ *bufp = m->buf + m->count;
+ else
+ *bufp = NULL;
+
+ return m->size - m->count;
+}
+
+/**
+ * seq_commit - commit data to the buffer
+ * @m: the seq_file handle
+ * @num: the number of bytes to commit
+ *
+ * Commit @num bytes of data written to a buffer previously acquired
+ * by seq_buf_get. To signal an error condition, or that the data
+ * didn't fit in the available space, pass a negative @num value.
+ */
+static inline void seq_commit(struct seq_file *m, int num)
+{
+ if (num < 0) {
+ m->count = m->size;
+ } else {
+ BUG_ON(m->count + num > m->size);
+ m->count += num;
+ }
+}
+
char *mangle_path(char *s, char *p, char *esc);
int seq_open(struct file *, const struct seq_operations *);
ssize_t seq_read(struct file *, char __user *, size_t, loff_t *);
/* Qualcomm MSM SoCs */
#define PORT_MSM 88
+/* BCM63xx family SoCs */
+#define PORT_BCM63XX 89
+
#ifdef __KERNEL__
#include <linux/compiler.h>
}
extern int next_signal(struct sigpending *pending, sigset_t *mask);
+extern int do_send_sig_info(int sig, struct siginfo *info,
+ struct task_struct *p, bool group);
extern int group_send_sig_info(int sig, struct siginfo *info, struct task_struct *p);
extern int __group_send_sig_info(int, struct siginfo *, struct task_struct *);
extern long do_rt_tgsigqueueinfo(pid_t tgid, pid_t pid, int sig,
--- /dev/null
+/*
+ * lms283gf05.h - Platform glue for Samsung LMS283GF05 LCD
+ *
+ * Copyright (C) 2009 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+*/
+
+#ifndef _INCLUDE_LINUX_SPI_LMS283GF05_H_
+#define _INCLUDE_LINUX_SPI_LMS283GF05_H_
+
+struct lms283gf05_pdata {
+ unsigned long reset_gpio;
+ bool reset_inverted;
+};
+
+#endif /* _INCLUDE_LINUX_SPI_LMS283GF05_H_ */
* the type/offset into the pte as 5/27 as well.
*/
#define MAX_SWAPFILES_SHIFT 5
-#ifndef CONFIG_MIGRATION
-#define MAX_SWAPFILES (1 << MAX_SWAPFILES_SHIFT)
+
+/*
+ * Use some of the swap files numbers for other purposes. This
+ * is a convenient way to hook into the VM to trigger special
+ * actions on faults.
+ */
+
+/*
+ * NUMA node memory migration support
+ */
+#ifdef CONFIG_MIGRATION
+#define SWP_MIGRATION_NUM 2
+#define SWP_MIGRATION_READ (MAX_SWAPFILES + SWP_HWPOISON_NUM)
+#define SWP_MIGRATION_WRITE (MAX_SWAPFILES + SWP_HWPOISON_NUM + 1)
#else
-/* Use last two entries for page migration swap entries */
-#define MAX_SWAPFILES ((1 << MAX_SWAPFILES_SHIFT)-2)
-#define SWP_MIGRATION_READ MAX_SWAPFILES
-#define SWP_MIGRATION_WRITE (MAX_SWAPFILES + 1)
+#define SWP_MIGRATION_NUM 0
#endif
+/*
+ * Handling of hardware poisoned pages with memory corruption.
+ */
+#ifdef CONFIG_MEMORY_FAILURE
+#define SWP_HWPOISON_NUM 1
+#define SWP_HWPOISON MAX_SWAPFILES
+#else
+#define SWP_HWPOISON_NUM 0
+#endif
+
+#define MAX_SWAPFILES \
+ ((1 << MAX_SWAPFILES_SHIFT) - SWP_MIGRATION_NUM - SWP_HWPOISON_NUM)
+
/*
* Magic header for a swap area. The first part of the union is
* what the swap magic looks like for the old (limited to 128MB)
extern unsigned long try_to_free_mem_cgroup_pages(struct mem_cgroup *mem,
gfp_t gfp_mask, bool noswap,
unsigned int swappiness);
+extern unsigned long mem_cgroup_shrink_node_zone(struct mem_cgroup *mem,
+ gfp_t gfp_mask, bool noswap,
+ unsigned int swappiness,
+ struct zone *zone,
+ int nid);
extern int __isolate_lru_page(struct page *page, int mode, int file);
extern unsigned long shrink_all_memory(unsigned long nr_pages);
extern int vm_swappiness;
extern void scan_mapping_unevictable_pages(struct address_space *);
extern unsigned long scan_unevictable_pages;
-extern int scan_unevictable_handler(struct ctl_table *, int, struct file *,
+extern int scan_unevictable_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
extern int scan_unevictable_register_node(struct node *node);
extern void scan_unevictable_unregister_node(struct node *node);
#endif
+#ifdef CONFIG_MEMORY_FAILURE
+/*
+ * Support for hardware poisoned pages
+ */
+static inline swp_entry_t make_hwpoison_entry(struct page *page)
+{
+ BUG_ON(!PageLocked(page));
+ return swp_entry(SWP_HWPOISON, page_to_pfn(page));
+}
+
+static inline int is_hwpoison_entry(swp_entry_t entry)
+{
+ return swp_type(entry) == SWP_HWPOISON;
+}
+#else
+
+static inline swp_entry_t make_hwpoison_entry(struct page *page)
+{
+ return swp_entry(0, 0);
+}
+
+static inline int is_hwpoison_entry(swp_entry_t swp)
+{
+ return 0;
+}
+#endif
+
+#if defined(CONFIG_MEMORY_FAILURE) || defined(CONFIG_MIGRATION)
+static inline int non_swap_entry(swp_entry_t entry)
+{
+ return swp_type(entry) >= MAX_SWAPFILES;
+}
+#else
+static inline int non_swap_entry(swp_entry_t entry)
+{
+ return 0;
+}
+#endif
#include <linux/types.h>
#include <linux/compiler.h>
-struct file;
struct completion;
#define CTL_MAXNAME 10 /* how many path components do we allow in a
void __user *oldval, size_t __user *oldlenp,
void __user *newval, size_t newlen);
-typedef int proc_handler (struct ctl_table *ctl, int write, struct file * filp,
+typedef int proc_handler (struct ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos);
-extern int proc_dostring(struct ctl_table *, int, struct file *,
+extern int proc_dostring(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-extern int proc_dointvec(struct ctl_table *, int, struct file *,
+extern int proc_dointvec(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-extern int proc_dointvec_minmax(struct ctl_table *, int, struct file *,
+extern int proc_dointvec_minmax(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-extern int proc_dointvec_jiffies(struct ctl_table *, int, struct file *,
+extern int proc_dointvec_jiffies(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-extern int proc_dointvec_userhz_jiffies(struct ctl_table *, int, struct file *,
+extern int proc_dointvec_userhz_jiffies(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-extern int proc_dointvec_ms_jiffies(struct ctl_table *, int, struct file *,
+extern int proc_dointvec_ms_jiffies(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-extern int proc_doulongvec_minmax(struct ctl_table *, int, struct file *,
+extern int proc_doulongvec_minmax(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
extern int proc_doulongvec_ms_jiffies_minmax(struct ctl_table *table, int,
- struct file *, void __user *, size_t *, loff_t *);
+ void __user *, size_t *, loff_t *);
extern int do_sysctl (int __user *name, int nlen,
void __user *oldval, size_t __user *oldlenp,
struct tms;
extern void do_sys_times(struct tms *);
+/*
+ * Similar to the struct tm in userspace <time.h>, but it needs to be here so
+ * that the kernel source is self contained.
+ */
+struct tm {
+ /*
+ * the number of seconds after the minute, normally in the range
+ * 0 to 59, but can be up to 60 to allow for leap seconds
+ */
+ int tm_sec;
+ /* the number of minutes after the hour, in the range 0 to 59*/
+ int tm_min;
+ /* the number of hours past midnight, in the range 0 to 23 */
+ int tm_hour;
+ /* the day of the month, in the range 1 to 31 */
+ int tm_mday;
+ /* the number of months since January, in the range 0 to 11 */
+ int tm_mon;
+ /* the number of years since 1900 */
+ long tm_year;
+ /* the number of days since Sunday, in the range 0 to 6 */
+ int tm_wday;
+ /* the number of days since January 1, in the range 0 to 365 */
+ int tm_yday;
+};
+
+void time_to_tm(time_t totalsecs, int offset, struct tm *result);
+
/**
* timespec_to_ns - Convert timespec to nanoseconds
* @ts: pointer to the timespec variable to be converted
/*
* Tracing hooks
*
- * Copyright (C) 2008 Red Hat, Inc. All rights reserved.
+ * Copyright (C) 2008-2009 Red Hat, Inc. All rights reserved.
*
* This copyrighted material is made available to anyone wishing to use,
* modify, copy, or redistribute it subject to the terms and conditions
/**
* tracehook_notify_jctl - report about job control stop/continue
- * @notify: nonzero if this is the last thread in the group to stop
+ * @notify: zero, %CLD_STOPPED or %CLD_CONTINUED
* @why: %CLD_STOPPED or %CLD_CONTINUED
*
* This is called when we might call do_notify_parent_cldstop().
- * It's called when about to stop for job control; we are already in
- * %TASK_STOPPED state, about to call schedule(). It's also called when
- * a delayed %CLD_STOPPED or %CLD_CONTINUED report is ready to be made.
*
- * Return nonzero to generate a %SIGCHLD with @why, which is
- * normal if @notify is nonzero.
+ * @notify is zero if we would not ordinarily send a %SIGCHLD,
+ * or is the %CLD_STOPPED or %CLD_CONTINUED .si_code for %SIGCHLD.
*
- * Called with no locks held.
+ * @why is %CLD_STOPPED when about to stop for job control;
+ * we are already in %TASK_STOPPED state, about to call schedule().
+ * It might also be that we have just exited (check %PF_EXITING),
+ * but need to report that a group-wide stop is complete.
+ *
+ * @why is %CLD_CONTINUED when waking up after job control stop and
+ * ready to make a delayed @notify report.
+ *
+ * Return the %CLD_* value for %SIGCHLD, or zero to generate no signal.
+ *
+ * Called with the siglock held.
*/
static inline int tracehook_notify_jctl(int notify, int why)
{
- return notify || (current->ptrace & PT_PTRACED);
+ return notify ?: (current->ptrace & PT_PTRACED) ? why : 0;
+}
+
+/**
+ * tracehook_finish_jctl - report about return from job control stop
+ *
+ * This is called by do_signal_stop() after wakeup.
+ */
+static inline void tracehook_finish_jctl(void)
+{
}
#define DEATH_REAP -1
/*
* Kernel Tracepoint API.
*
- * See Documentation/tracepoint.txt.
+ * See Documentation/trace/tracepoints.txt.
*
* (C) Copyright 2008 Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
*
#ifndef DECLARE_TRACE
#define TP_PROTO(args...) args
-#define TP_ARGS(args...) args
+#define TP_ARGS(args...) args
#ifdef CONFIG_TRACEPOINTS
*
* void (*shutdown)(struct tty_struct * tty);
*
- * This routine is called when a particular tty device is closed for
- * the last time freeing up the resources.
+ * This routine is called synchronously when a particular tty device
+ * is closed for the last time freeing up the resources.
+ *
+ *
+ * void (*cleanup)(struct tty_struct * tty);
+ *
+ * This routine is called asynchronously when a particular tty device
+ * is closed for the last time freeing up the resources. This is
+ * actually the second part of shutdown for routines that might sleep.
+ *
*
* int (*write)(struct tty_struct * tty,
* const unsigned char *buf, int count);
int (*open)(struct tty_struct * tty, struct file * filp);
void (*close)(struct tty_struct * tty, struct file * filp);
void (*shutdown)(struct tty_struct *tty);
+ void (*cleanup)(struct tty_struct *tty);
int (*write)(struct tty_struct * tty,
const unsigned char *buf, int count);
int (*put_char)(struct tty_struct *tty, unsigned char ch);
#ifndef _LINUX_UNALIGNED_BE_BYTESHIFT_H
#define _LINUX_UNALIGNED_BE_BYTESHIFT_H
-#include <linux/kernel.h>
+#include <linux/types.h>
static inline u16 __get_unaligned_be16(const u8 *p)
{
#ifndef _LINUX_UNALIGNED_LE_BYTESHIFT_H
#define _LINUX_UNALIGNED_LE_BYTESHIFT_H
-#include <linux/kernel.h>
+#include <linux/types.h>
static inline u16 __get_unaligned_le16(const u8 *p)
{
#define FLAG_FRAMING_AX 0x0040 /* AX88772/178 packets */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_AVOID_UNLINK_URBS 0x0100 /* don't unlink urbs at usbnet_stop() */
+#define FLAG_SEND_ZLP 0x0200 /* hw requires ZLPs are sent */
/* init device ... can sleep, or cause probe() failure */
/*
- * vgaarb.c
+ * The VGA aribiter manages VGA space routing and VGA resource decode to
+ * allow multiple VGA devices to be used in a system in a safe way.
*
* (C) Copyright 2005 Benjamin Herrenschmidt <benh@kernel.crashing.org>
* (C) Copyright 2007 Paulo R. Zanoni <przanoni@gmail.com>
extern unsigned long determine_dirtyable_memory(void);
extern int dirty_background_ratio_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
extern int dirty_background_bytes_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
extern int dirty_ratio_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
extern int dirty_bytes_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos);
struct ctl_table;
-struct file;
-int dirty_writeback_centisecs_handler(struct ctl_table *, int, struct file *,
+int dirty_writeback_centisecs_handler(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
void get_dirty_limits(unsigned long *pbackground, unsigned long *pdirty,
extern int cmsghdr_from_user_compat_to_kern(struct msghdr *, struct sock *, unsigned char *, int);
-extern int compat_mc_setsockopt(struct sock *, int, int, char __user *, int,
- int (*)(struct sock *, int, int, char __user *, int));
+extern int compat_mc_setsockopt(struct sock *, int, int, char __user *, unsigned int,
+ int (*)(struct sock *, int, int, char __user *, unsigned int));
extern int compat_mc_getsockopt(struct sock *, int, int, char __user *,
int __user *, int (*)(struct sock *, int, int, char __user *,
int __user *));
u16 net_header_len;
u16 sockaddr_len;
int (*setsockopt)(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
int (*getsockopt)(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
#ifdef CONFIG_COMPAT
int (*compat_setsockopt)(struct sock *sk,
int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
int (*compat_getsockopt)(struct sock *sk,
int level, int optname,
char __user *optval, int __user *optlen);
extern int inet_csk_compat_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
extern int inet_csk_compat_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
#endif /* _INET_CONNECTION_SOCK_H */
extern void ip_cmsg_recv(struct msghdr *msg, struct sk_buff *skb);
extern int ip_cmsg_send(struct net *net,
struct msghdr *msg, struct ipcm_cookie *ipc);
-extern int ip_setsockopt(struct sock *sk, int level, int optname, char __user *optval, int optlen);
+extern int ip_setsockopt(struct sock *sk, int level, int optname, char __user *optval, unsigned int optlen);
extern int ip_getsockopt(struct sock *sk, int level, int optname, char __user *optval, int __user *optlen);
extern int compat_ip_setsockopt(struct sock *sk, int level,
- int optname, char __user *optval, int optlen);
+ int optname, char __user *optval, unsigned int optlen);
extern int compat_ip_getsockopt(struct sock *sk, int level,
int optname, char __user *optval, int __user *optlen);
extern int ip_ra_control(struct sock *sk, unsigned char on, void (*destructor)(struct sock *));
* fed into the routing cache should use these handlers.
*/
int ipv4_doint_and_flush(ctl_table *ctl, int write,
- struct file* filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos);
int ipv4_doint_and_flush_strategy(ctl_table *table,
void __user *oldval, size_t __user *oldlenp,
struct ip_tunnel *next;
struct net_device *dev;
- int recursion; /* Depth of hard_start_xmit recursion */
int err_count; /* Number of arrived ICMP errors */
unsigned long err_time; /* Time when the last ICMP error arrived */
unsigned int prl_count; /* # of entries in PRL */
};
-/* ISATAP: default interval between RS in secondy */
-#define IPTUNNEL_RS_DEFAULT_DELAY (900)
-
struct ip_tunnel_prl_entry
{
struct ip_tunnel_prl_entry *next;
__be32 addr;
u16 flags;
- unsigned long rs_delay;
- struct timer_list rs_timer;
- struct ip_tunnel *tunnel;
- spinlock_t lock;
};
#define IPTUNNEL_XMIT() do { \
extern int ipv6_setsockopt(struct sock *sk, int level,
int optname,
char __user *optval,
- int optlen);
+ unsigned int optlen);
extern int ipv6_getsockopt(struct sock *sk, int level,
int optname,
char __user *optval,
int level,
int optname,
char __user *optval,
- int optlen);
+ unsigned int optlen);
extern int compat_ipv6_getsockopt(struct sock *sk,
int level,
int optname,
#include <net/neighbour.h>
struct ctl_table;
-struct file;
struct inet6_dev;
struct net_device;
struct net_proto_family;
#ifdef CONFIG_SYSCTL
extern int ndisc_ifinfo_sysctl_change(struct ctl_table *ctl,
int write,
- struct file * filp,
void __user *buffer,
size_t *lenp,
loff_t *ppos);
int level,
int optname,
char __user *optval,
- int optlen);
+ unsigned int optlen);
int (*getsockopt) (struct sock *sk,
int level,
int optname,
int level,
int optname,
char __user *optval,
- int optlen);
+ unsigned int optlen);
int (*compat_getsockopt) (struct sock *sk,
int level,
int optname,
void (*shutdown)(struct sock *sk, int how);
int (*setsockopt)(struct sock *sk, int level,
int optname, char __user *optval,
- int optlen);
+ unsigned int optlen);
int (*getsockopt)(struct sock *sk, int level,
int optname, char __user *optval,
int __user *option);
int (*compat_setsockopt)(struct sock *sk,
int level,
int optname, char __user *optval,
- int optlen);
+ unsigned int optlen);
int (*compat_getsockopt)(struct sock *sk,
int level,
int optname, char __user *optval,
extern int sock_setsockopt(struct socket *sock, int level,
int op, char __user *optval,
- int optlen);
+ unsigned int optlen);
extern int sock_getsockopt(struct socket *sock, int level,
int op, char __user *optval,
extern int sock_no_getsockopt(struct socket *, int , int,
char __user *, int __user *);
extern int sock_no_setsockopt(struct socket *, int, int,
- char __user *, int);
+ char __user *, unsigned int);
extern int sock_no_sendmsg(struct kiocb *, struct socket *,
struct msghdr *, size_t);
extern int sock_no_recvmsg(struct kiocb *, struct socket *,
extern int sock_common_recvmsg(struct kiocb *iocb, struct socket *sock,
struct msghdr *msg, size_t size, int flags);
extern int sock_common_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
extern int compat_sock_common_getsockopt(struct socket *sock, int level,
int optname, char __user *optval, int __user *optlen);
extern int compat_sock_common_setsockopt(struct socket *sock, int level,
- int optname, char __user *optval, int optlen);
+ int optname, char __user *optval, unsigned int optlen);
extern void sk_common_release(struct sock *sk);
int __user *optlen);
extern int tcp_setsockopt(struct sock *sk, int level,
int optname, char __user *optval,
- int optlen);
+ unsigned int optlen);
extern int compat_tcp_getsockopt(struct sock *sk,
int level, int optname,
char __user *optval, int __user *optlen);
extern int compat_tcp_setsockopt(struct sock *sk,
int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
extern void tcp_set_keepalive(struct sock *sk, int val);
extern int tcp_recvmsg(struct kiocb *iocb, struct sock *sk,
struct msghdr *msg,
extern int udp_lib_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
extern int udp_lib_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen,
+ char __user *optval, unsigned int optlen,
int (*push_pending_frames)(struct sock *));
extern struct sock *udp4_lib_lookup(struct net *net, __be32 saddr, __be16 sport,
void __user *arg);
extern int compat_wext_handle_ioctl(struct net *net, unsigned int cmd,
unsigned long arg);
+extern struct iw_statistics *get_wireless_stats(struct net_device *dev);
#else
static inline int wext_proc_init(struct net *net)
{
extern struct pccard_resource_ops pccard_nonstatic_ops;
/* socket drivers are expected to use these callbacks in their .drv struct */
-extern int pcmcia_socket_dev_suspend(struct device *dev, pm_message_t state);
+extern int pcmcia_socket_dev_suspend(struct device *dev);
extern int pcmcia_socket_dev_resume(struct device *dev);
/* socket drivers use this callback in their IRQ handler */
(unsigned long long)__entry->old_sector)
);
+TRACE_EVENT(block_rq_remap,
+
+ TP_PROTO(struct request_queue *q, struct request *rq, dev_t dev,
+ sector_t from),
+
+ TP_ARGS(q, rq, dev, from),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( sector_t, sector )
+ __field( unsigned int, nr_sector )
+ __field( dev_t, old_dev )
+ __field( sector_t, old_sector )
+ __array( char, rwbs, 6 )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = disk_devt(rq->rq_disk);
+ __entry->sector = blk_rq_pos(rq);
+ __entry->nr_sector = blk_rq_sectors(rq);
+ __entry->old_dev = dev;
+ __entry->old_sector = from;
+ blk_fill_rwbs_rq(__entry->rwbs, rq);
+ ),
+
+ TP_printk("%d,%d %s %llu + %u <- (%d,%d) %llu",
+ MAJOR(__entry->dev), MINOR(__entry->dev), __entry->rwbs,
+ (unsigned long long)__entry->sector,
+ __entry->nr_sector,
+ MAJOR(__entry->old_dev), MINOR(__entry->old_dev),
+ (unsigned long long)__entry->old_sector)
+);
+
#endif /* _TRACE_BLOCK_H */
/* This part must be outside protection */
struct ext4_allocation_request;
struct ext4_prealloc_space;
struct ext4_inode_info;
+struct mpage_da_data;
#define EXT4_I(inode) (container_of(inode, struct ext4_inode_info, vfs_inode))
__field( char, for_kupdate )
__field( char, for_reclaim )
__field( char, range_cyclic )
+ __field( pgoff_t, writeback_index )
),
TP_fast_assign(
__entry->for_kupdate = wbc->for_kupdate;
__entry->for_reclaim = wbc->for_reclaim;
__entry->range_cyclic = wbc->range_cyclic;
+ __entry->writeback_index = inode->i_mapping->writeback_index;
),
- TP_printk("dev %s ino %lu nr_to_write %ld pages_skipped %ld range_start %llu range_end %llu nonblocking %d for_kupdate %d for_reclaim %d range_cyclic %d",
+ TP_printk("dev %s ino %lu nr_to_write %ld pages_skipped %ld range_start %llu range_end %llu nonblocking %d for_kupdate %d for_reclaim %d range_cyclic %d writeback_index %lu",
jbd2_dev_to_name(__entry->dev),
(unsigned long) __entry->ino, __entry->nr_to_write,
__entry->pages_skipped, __entry->range_start,
__entry->range_end, __entry->nonblocking,
__entry->for_kupdate, __entry->for_reclaim,
- __entry->range_cyclic)
+ __entry->range_cyclic,
+ (unsigned long) __entry->writeback_index)
);
TRACE_EVENT(ext4_da_write_pages,
__field( char, encountered_congestion )
__field( char, more_io )
__field( char, no_nrwrite_index_update )
+ __field( pgoff_t, writeback_index )
),
TP_fast_assign(
__entry->encountered_congestion = wbc->encountered_congestion;
__entry->more_io = wbc->more_io;
__entry->no_nrwrite_index_update = wbc->no_nrwrite_index_update;
+ __entry->writeback_index = inode->i_mapping->writeback_index;
),
- TP_printk("dev %s ino %lu ret %d pages_written %d pages_skipped %ld congestion %d more_io %d no_nrwrite_index_update %d",
+ TP_printk("dev %s ino %lu ret %d pages_written %d pages_skipped %ld congestion %d more_io %d no_nrwrite_index_update %d writeback_index %lu",
jbd2_dev_to_name(__entry->dev),
(unsigned long) __entry->ino, __entry->ret,
__entry->pages_written, __entry->pages_skipped,
__entry->encountered_congestion, __entry->more_io,
- __entry->no_nrwrite_index_update)
+ __entry->no_nrwrite_index_update,
+ (unsigned long) __entry->writeback_index)
);
TRACE_EVENT(ext4_da_write_begin,
__entry->data_blocks, __entry->meta_blocks)
);
+TRACE_EVENT(ext4_mballoc_alloc,
+ TP_PROTO(struct ext4_allocation_context *ac),
+
+ TP_ARGS(ac),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( ino_t, ino )
+ __field( __u16, found )
+ __field( __u16, groups )
+ __field( __u16, buddy )
+ __field( __u16, flags )
+ __field( __u16, tail )
+ __field( __u8, cr )
+ __field( __u32, orig_logical )
+ __field( int, orig_start )
+ __field( __u32, orig_group )
+ __field( int, orig_len )
+ __field( __u32, goal_logical )
+ __field( int, goal_start )
+ __field( __u32, goal_group )
+ __field( int, goal_len )
+ __field( __u32, result_logical )
+ __field( int, result_start )
+ __field( __u32, result_group )
+ __field( int, result_len )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = ac->ac_inode->i_sb->s_dev;
+ __entry->ino = ac->ac_inode->i_ino;
+ __entry->found = ac->ac_found;
+ __entry->flags = ac->ac_flags;
+ __entry->groups = ac->ac_groups_scanned;
+ __entry->buddy = ac->ac_buddy;
+ __entry->tail = ac->ac_tail;
+ __entry->cr = ac->ac_criteria;
+ __entry->orig_logical = ac->ac_o_ex.fe_logical;
+ __entry->orig_start = ac->ac_o_ex.fe_start;
+ __entry->orig_group = ac->ac_o_ex.fe_group;
+ __entry->orig_len = ac->ac_o_ex.fe_len;
+ __entry->goal_logical = ac->ac_g_ex.fe_logical;
+ __entry->goal_start = ac->ac_g_ex.fe_start;
+ __entry->goal_group = ac->ac_g_ex.fe_group;
+ __entry->goal_len = ac->ac_g_ex.fe_len;
+ __entry->result_logical = ac->ac_f_ex.fe_logical;
+ __entry->result_start = ac->ac_f_ex.fe_start;
+ __entry->result_group = ac->ac_f_ex.fe_group;
+ __entry->result_len = ac->ac_f_ex.fe_len;
+ ),
+
+ TP_printk("dev %s inode %lu orig %u/%d/%u@%u goal %u/%d/%u@%u "
+ "result %u/%d/%u@%u blks %u grps %u cr %u flags 0x%04x "
+ "tail %u broken %u",
+ jbd2_dev_to_name(__entry->dev), (unsigned long) __entry->ino,
+ __entry->orig_group, __entry->orig_start,
+ __entry->orig_len, __entry->orig_logical,
+ __entry->goal_group, __entry->goal_start,
+ __entry->goal_len, __entry->goal_logical,
+ __entry->result_group, __entry->result_start,
+ __entry->result_len, __entry->result_logical,
+ __entry->found, __entry->groups, __entry->cr,
+ __entry->flags, __entry->tail,
+ __entry->buddy ? 1 << __entry->buddy : 0)
+);
+
+TRACE_EVENT(ext4_mballoc_prealloc,
+ TP_PROTO(struct ext4_allocation_context *ac),
+
+ TP_ARGS(ac),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( ino_t, ino )
+ __field( __u32, orig_logical )
+ __field( int, orig_start )
+ __field( __u32, orig_group )
+ __field( int, orig_len )
+ __field( __u32, result_logical )
+ __field( int, result_start )
+ __field( __u32, result_group )
+ __field( int, result_len )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = ac->ac_inode->i_sb->s_dev;
+ __entry->ino = ac->ac_inode->i_ino;
+ __entry->orig_logical = ac->ac_o_ex.fe_logical;
+ __entry->orig_start = ac->ac_o_ex.fe_start;
+ __entry->orig_group = ac->ac_o_ex.fe_group;
+ __entry->orig_len = ac->ac_o_ex.fe_len;
+ __entry->result_logical = ac->ac_b_ex.fe_logical;
+ __entry->result_start = ac->ac_b_ex.fe_start;
+ __entry->result_group = ac->ac_b_ex.fe_group;
+ __entry->result_len = ac->ac_b_ex.fe_len;
+ ),
+
+ TP_printk("dev %s inode %lu orig %u/%d/%u@%u result %u/%d/%u@%u",
+ jbd2_dev_to_name(__entry->dev), (unsigned long) __entry->ino,
+ __entry->orig_group, __entry->orig_start,
+ __entry->orig_len, __entry->orig_logical,
+ __entry->result_group, __entry->result_start,
+ __entry->result_len, __entry->result_logical)
+);
+
+TRACE_EVENT(ext4_mballoc_discard,
+ TP_PROTO(struct ext4_allocation_context *ac),
+
+ TP_ARGS(ac),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( ino_t, ino )
+ __field( __u32, result_logical )
+ __field( int, result_start )
+ __field( __u32, result_group )
+ __field( int, result_len )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = ac->ac_inode->i_sb->s_dev;
+ __entry->ino = ac->ac_inode->i_ino;
+ __entry->result_logical = ac->ac_b_ex.fe_logical;
+ __entry->result_start = ac->ac_b_ex.fe_start;
+ __entry->result_group = ac->ac_b_ex.fe_group;
+ __entry->result_len = ac->ac_b_ex.fe_len;
+ ),
+
+ TP_printk("dev %s inode %lu extent %u/%d/%u@%u ",
+ jbd2_dev_to_name(__entry->dev), (unsigned long) __entry->ino,
+ __entry->result_group, __entry->result_start,
+ __entry->result_len, __entry->result_logical)
+);
+
+TRACE_EVENT(ext4_mballoc_free,
+ TP_PROTO(struct ext4_allocation_context *ac),
+
+ TP_ARGS(ac),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( ino_t, ino )
+ __field( __u32, result_logical )
+ __field( int, result_start )
+ __field( __u32, result_group )
+ __field( int, result_len )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = ac->ac_inode->i_sb->s_dev;
+ __entry->ino = ac->ac_inode->i_ino;
+ __entry->result_logical = ac->ac_b_ex.fe_logical;
+ __entry->result_start = ac->ac_b_ex.fe_start;
+ __entry->result_group = ac->ac_b_ex.fe_group;
+ __entry->result_len = ac->ac_b_ex.fe_len;
+ ),
+
+ TP_printk("dev %s inode %lu extent %u/%d/%u@%u ",
+ jbd2_dev_to_name(__entry->dev), (unsigned long) __entry->ino,
+ __entry->result_group, __entry->result_start,
+ __entry->result_len, __entry->result_logical)
+);
+
#endif /* _TRACE_EXT4_H */
/* This part must be outside protection */
#include <linux/jbd2.h>
#include <linux/tracepoint.h>
+struct transaction_chp_stats_s;
+struct transaction_run_stats_s;
+
TRACE_EVENT(jbd2_checkpoint,
TP_PROTO(journal_t *journal, int result),
jbd2_dev_to_name(__entry->dev), (unsigned long) __entry->ino)
);
+TRACE_EVENT(jbd2_run_stats,
+ TP_PROTO(dev_t dev, unsigned long tid,
+ struct transaction_run_stats_s *stats),
+
+ TP_ARGS(dev, tid, stats),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( unsigned long, tid )
+ __field( unsigned long, wait )
+ __field( unsigned long, running )
+ __field( unsigned long, locked )
+ __field( unsigned long, flushing )
+ __field( unsigned long, logging )
+ __field( __u32, handle_count )
+ __field( __u32, blocks )
+ __field( __u32, blocks_logged )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->tid = tid;
+ __entry->wait = stats->rs_wait;
+ __entry->running = stats->rs_running;
+ __entry->locked = stats->rs_locked;
+ __entry->flushing = stats->rs_flushing;
+ __entry->logging = stats->rs_logging;
+ __entry->handle_count = stats->rs_handle_count;
+ __entry->blocks = stats->rs_blocks;
+ __entry->blocks_logged = stats->rs_blocks_logged;
+ ),
+
+ TP_printk("dev %s tid %lu wait %u running %u locked %u flushing %u "
+ "logging %u handle_count %u blocks %u blocks_logged %u",
+ jbd2_dev_to_name(__entry->dev), __entry->tid,
+ jiffies_to_msecs(__entry->wait),
+ jiffies_to_msecs(__entry->running),
+ jiffies_to_msecs(__entry->locked),
+ jiffies_to_msecs(__entry->flushing),
+ jiffies_to_msecs(__entry->logging),
+ __entry->handle_count, __entry->blocks,
+ __entry->blocks_logged)
+);
+
+TRACE_EVENT(jbd2_checkpoint_stats,
+ TP_PROTO(dev_t dev, unsigned long tid,
+ struct transaction_chp_stats_s *stats),
+
+ TP_ARGS(dev, tid, stats),
+
+ TP_STRUCT__entry(
+ __field( dev_t, dev )
+ __field( unsigned long, tid )
+ __field( unsigned long, chp_time )
+ __field( __u32, forced_to_close )
+ __field( __u32, written )
+ __field( __u32, dropped )
+ ),
+
+ TP_fast_assign(
+ __entry->dev = dev;
+ __entry->tid = tid;
+ __entry->chp_time = stats->cs_chp_time;
+ __entry->forced_to_close= stats->cs_forced_to_close;
+ __entry->written = stats->cs_written;
+ __entry->dropped = stats->cs_dropped;
+ ),
+
+ TP_printk("dev %s tid %lu chp_time %u forced_to_close %u "
+ "written %u dropped %u",
+ jbd2_dev_to_name(__entry->dev), __entry->tid,
+ jiffies_to_msecs(__entry->chp_time),
+ __entry->forced_to_close, __entry->written, __entry->dropped)
+);
+
#endif /* _TRACE_JBD2_H */
/* This part must be outside protection */
__entry->func = work->func;
),
- TP_printk("thread=%s:%d func=%pF", __entry->thread_comm,
+ TP_printk("thread=%s:%d func=%pf", __entry->thread_comm,
__entry->thread_pid, __entry->func)
);
__entry->func = work->func;
),
- TP_printk("thread=%s:%d func=%pF", __entry->thread_comm,
+ TP_printk("thread=%s:%d func=%pf", __entry->thread_comm,
__entry->thread_pid, __entry->func)
);
}
#ifdef CONFIG_PROC_SYSCTL
-static int proc_ipc_dointvec(ctl_table *table, int write, struct file *filp,
+static int proc_ipc_dointvec(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table ipc_table;
memcpy(&ipc_table, table, sizeof(ipc_table));
ipc_table.data = get_ipc(table);
- return proc_dointvec(&ipc_table, write, filp, buffer, lenp, ppos);
+ return proc_dointvec(&ipc_table, write, buffer, lenp, ppos);
}
static int proc_ipc_callback_dointvec(ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp, loff_t *ppos)
+ void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table ipc_table;
size_t lenp_bef = *lenp;
memcpy(&ipc_table, table, sizeof(ipc_table));
ipc_table.data = get_ipc(table);
- rc = proc_dointvec(&ipc_table, write, filp, buffer, lenp, ppos);
+ rc = proc_dointvec(&ipc_table, write, buffer, lenp, ppos);
if (write && !rc && lenp_bef == *lenp)
/*
}
static int proc_ipc_doulongvec_minmax(ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp, loff_t *ppos)
+ void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table ipc_table;
memcpy(&ipc_table, table, sizeof(ipc_table));
ipc_table.data = get_ipc(table);
- return proc_doulongvec_minmax(&ipc_table, write, filp, buffer,
+ return proc_doulongvec_minmax(&ipc_table, write, buffer,
lenp, ppos);
}
}
static int proc_ipcauto_dointvec_minmax(ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp, loff_t *ppos)
+ void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table ipc_table;
size_t lenp_bef = *lenp;
ipc_table.data = get_ipc(table);
oldval = *((int *)(ipc_table.data));
- rc = proc_dointvec_minmax(&ipc_table, write, filp, buffer, lenp, ppos);
+ rc = proc_dointvec_minmax(&ipc_table, write, buffer, lenp, ppos);
if (write && !rc && lenp_bef == *lenp) {
int newval = *((int *)(ipc_table.data));
return which;
}
-static int proc_mq_dointvec(ctl_table *table, int write, struct file *filp,
+static int proc_mq_dointvec(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table mq_table;
memcpy(&mq_table, table, sizeof(mq_table));
mq_table.data = get_mq(table);
- return proc_dointvec(&mq_table, write, filp, buffer, lenp, ppos);
+ return proc_dointvec(&mq_table, write, buffer, lenp, ppos);
}
static int proc_mq_dointvec_minmax(ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp, loff_t *ppos)
+ void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table mq_table;
memcpy(&mq_table, table, sizeof(mq_table));
mq_table.data = get_mq(table);
- return proc_dointvec_minmax(&mq_table, write, filp, buffer,
+ return proc_dointvec_minmax(&mq_table, write, buffer,
lenp, ppos);
}
#else
#define shm_file_data(file) (*((struct shm_file_data **)&(file)->private_data))
static const struct file_operations shm_file_operations;
-static struct vm_operations_struct shm_vm_ops;
+static const struct vm_operations_struct shm_vm_ops;
#define shm_ids(ns) ((ns)->ids[IPC_SHM_IDS])
.get_unmapped_area = shm_get_unmapped_area,
};
-static struct vm_operations_struct shm_vm_ops = {
+static const struct vm_operations_struct shm_vm_ops = {
.open = shm_open, /* callback for a new vm-area open */
.close = shm_close, /* callback for when the vm-area is released */
.fault = shm_fault,
obj-$(CONFIG_BACKTRACE_SELF_TEST) += backtracetest.o
obj-$(CONFIG_COMPAT) += compat.o
obj-$(CONFIG_CGROUPS) += cgroup.o
-obj-$(CONFIG_CGROUP_DEBUG) += cgroup_debug.o
obj-$(CONFIG_CGROUP_FREEZER) += cgroup_freezer.o
obj-$(CONFIG_CPUSETS) += cpuset.o
obj-$(CONFIG_CGROUP_NS) += ns_cgroup.o
break;
}
case AUDIT_SIGNAL_INFO:
- err = security_secid_to_secctx(audit_sig_sid, &ctx, &len);
- if (err)
- return err;
+ len = 0;
+ if (audit_sig_sid) {
+ err = security_secid_to_secctx(audit_sig_sid, &ctx, &len);
+ if (err)
+ return err;
+ }
sig_data = kmalloc(sizeof(*sig_data) + len, GFP_KERNEL);
if (!sig_data) {
- security_release_secctx(ctx, len);
+ if (audit_sig_sid)
+ security_release_secctx(ctx, len);
return -ENOMEM;
}
sig_data->uid = audit_sig_uid;
sig_data->pid = audit_sig_pid;
- memcpy(sig_data->ctx, ctx, len);
- security_release_secctx(ctx, len);
+ if (audit_sig_sid) {
+ memcpy(sig_data->ctx, ctx, len);
+ security_release_secctx(ctx, len);
+ }
audit_send_reply(NETLINK_CB(skb).pid, seq, AUDIT_SIGNAL_INFO,
0, 0, sig_data, sizeof(*sig_data) + len);
kfree(sig_data);
struct audit_watch {
atomic_t count; /* reference count */
- char *path; /* insertion path */
dev_t dev; /* associated superblock device */
+ char *path; /* insertion path */
unsigned long ino; /* associated inode number */
struct audit_parent *parent; /* associated parent */
struct list_head wlist; /* entry in parent->watches list */
int in_syscall; /* 1 if task is in a syscall */
enum audit_state state, current_state;
unsigned int serial; /* serial number for record */
- struct timespec ctime; /* time of syscall entry */
int major; /* syscall number */
+ struct timespec ctime; /* time of syscall entry */
unsigned long argv[4]; /* syscall arguments */
- int return_valid; /* return code is valid */
long return_code;/* syscall return code */
u64 prio;
+ int return_valid; /* return code is valid */
int name_count;
struct audit_names names[AUDIT_NAMES];
char * filterkey; /* key for rule that triggered record */
char target_comm[TASK_COMM_LEN];
struct audit_tree_refs *trees, *first_trees;
- int tree_count;
struct list_head killed_trees;
+ int tree_count;
int type;
union {
*/
#include <linux/cgroup.h>
+#include <linux/ctype.h>
#include <linux/errno.h>
#include <linux/fs.h>
#include <linux/kernel.h>
#include <linux/namei.h>
#include <linux/smp_lock.h>
#include <linux/pid_namespace.h>
+#include <linux/idr.h>
+#include <linux/vmalloc.h> /* TODO: replace with more sophisticated array */
#include <asm/atomic.h>
#include <linux/cgroup_subsys.h>
};
+#define MAX_CGROUP_ROOT_NAMELEN 64
+
/*
* A cgroupfs_root represents the root of a cgroup hierarchy,
* and may be associated with a superblock to form an active
*/
unsigned long subsys_bits;
+ /* Unique id for this hierarchy. */
+ int hierarchy_id;
+
/* The bitmask of subsystems currently attached to this hierarchy */
unsigned long actual_subsys_bits;
/* The path to use for release notifications. */
char release_agent_path[PATH_MAX];
+
+ /* The name for this hierarchy - may be empty */
+ char name[MAX_CGROUP_ROOT_NAMELEN];
};
/*
static LIST_HEAD(roots);
static int root_count;
+static DEFINE_IDA(hierarchy_ida);
+static int next_hierarchy_id;
+static DEFINE_SPINLOCK(hierarchy_id_lock);
+
/* dummytop is a shorthand for the dummy hierarchy's top cgroup */
#define dummytop (&rootnode.top_cgroup)
* cgroup, anchored on cgroup->css_sets
*/
struct list_head cgrp_link_list;
+ struct cgroup *cgrp;
/*
* List running through cg_cgroup_links pointing at a
* single css_set object, anchored on css_set->cg_links
static DEFINE_RWLOCK(css_set_lock);
static int css_set_count;
-/* hash table for cgroup groups. This improves the performance to
- * find an existing css_set */
+/*
+ * hash table for cgroup groups. This improves the performance to find
+ * an existing css_set. This hash doesn't (currently) take into
+ * account cgroups in empty hierarchies.
+ */
#define CSS_SET_HASH_BITS 7
#define CSS_SET_TABLE_SIZE (1 << CSS_SET_HASH_BITS)
static struct hlist_head css_set_table[CSS_SET_TABLE_SIZE];
return &css_set_table[index];
}
+static void free_css_set_rcu(struct rcu_head *obj)
+{
+ struct css_set *cg = container_of(obj, struct css_set, rcu_head);
+ kfree(cg);
+}
+
/* We don't maintain the lists running through each css_set to its
* task until after the first call to cgroup_iter_start(). This
* reduces the fork()/exit() overhead for people who have cgroups
* compiled into their kernel but not actually in use */
static int use_task_css_set_links __read_mostly;
-/* When we create or destroy a css_set, the operation simply
- * takes/releases a reference count on all the cgroups referenced
- * by subsystems in this css_set. This can end up multiple-counting
- * some cgroups, but that's OK - the ref-count is just a
- * busy/not-busy indicator; ensuring that we only count each cgroup
- * once would require taking a global lock to ensure that no
- * subsystems moved between hierarchies while we were doing so.
- *
- * Possible TODO: decide at boot time based on the number of
- * registered subsystems and the number of CPUs or NUMA nodes whether
- * it's better for performance to ref-count every subsystem, or to
- * take a global lock and only add one ref count to each hierarchy.
- */
-
-/*
- * unlink a css_set from the list and free it
- */
-static void unlink_css_set(struct css_set *cg)
+static void __put_css_set(struct css_set *cg, int taskexit)
{
struct cg_cgroup_link *link;
struct cg_cgroup_link *saved_link;
-
- hlist_del(&cg->hlist);
- css_set_count--;
-
- list_for_each_entry_safe(link, saved_link, &cg->cg_links,
- cg_link_list) {
- list_del(&link->cg_link_list);
- list_del(&link->cgrp_link_list);
- kfree(link);
- }
-}
-
-static void __put_css_set(struct css_set *cg, int taskexit)
-{
- int i;
/*
* Ensure that the refcount doesn't hit zero while any readers
* can see it. Similar to atomic_dec_and_lock(), but for an
write_unlock(&css_set_lock);
return;
}
- unlink_css_set(cg);
- write_unlock(&css_set_lock);
- rcu_read_lock();
- for (i = 0; i < CGROUP_SUBSYS_COUNT; i++) {
- struct cgroup *cgrp = rcu_dereference(cg->subsys[i]->cgroup);
+ /* This css_set is dead. unlink it and release cgroup refcounts */
+ hlist_del(&cg->hlist);
+ css_set_count--;
+
+ list_for_each_entry_safe(link, saved_link, &cg->cg_links,
+ cg_link_list) {
+ struct cgroup *cgrp = link->cgrp;
+ list_del(&link->cg_link_list);
+ list_del(&link->cgrp_link_list);
if (atomic_dec_and_test(&cgrp->count) &&
notify_on_release(cgrp)) {
if (taskexit)
set_bit(CGRP_RELEASABLE, &cgrp->flags);
check_for_release(cgrp);
}
+
+ kfree(link);
}
- rcu_read_unlock();
- kfree(cg);
+
+ write_unlock(&css_set_lock);
+ call_rcu(&cg->rcu_head, free_css_set_rcu);
}
/*
__put_css_set(cg, 1);
}
+/*
+ * compare_css_sets - helper function for find_existing_css_set().
+ * @cg: candidate css_set being tested
+ * @old_cg: existing css_set for a task
+ * @new_cgrp: cgroup that's being entered by the task
+ * @template: desired set of css pointers in css_set (pre-calculated)
+ *
+ * Returns true if "cg" matches "old_cg" except for the hierarchy
+ * which "new_cgrp" belongs to, for which it should match "new_cgrp".
+ */
+static bool compare_css_sets(struct css_set *cg,
+ struct css_set *old_cg,
+ struct cgroup *new_cgrp,
+ struct cgroup_subsys_state *template[])
+{
+ struct list_head *l1, *l2;
+
+ if (memcmp(template, cg->subsys, sizeof(cg->subsys))) {
+ /* Not all subsystems matched */
+ return false;
+ }
+
+ /*
+ * Compare cgroup pointers in order to distinguish between
+ * different cgroups in heirarchies with no subsystems. We
+ * could get by with just this check alone (and skip the
+ * memcmp above) but on most setups the memcmp check will
+ * avoid the need for this more expensive check on almost all
+ * candidates.
+ */
+
+ l1 = &cg->cg_links;
+ l2 = &old_cg->cg_links;
+ while (1) {
+ struct cg_cgroup_link *cgl1, *cgl2;
+ struct cgroup *cg1, *cg2;
+
+ l1 = l1->next;
+ l2 = l2->next;
+ /* See if we reached the end - both lists are equal length. */
+ if (l1 == &cg->cg_links) {
+ BUG_ON(l2 != &old_cg->cg_links);
+ break;
+ } else {
+ BUG_ON(l2 == &old_cg->cg_links);
+ }
+ /* Locate the cgroups associated with these links. */
+ cgl1 = list_entry(l1, struct cg_cgroup_link, cg_link_list);
+ cgl2 = list_entry(l2, struct cg_cgroup_link, cg_link_list);
+ cg1 = cgl1->cgrp;
+ cg2 = cgl2->cgrp;
+ /* Hierarchies should be linked in the same order. */
+ BUG_ON(cg1->root != cg2->root);
+
+ /*
+ * If this hierarchy is the hierarchy of the cgroup
+ * that's changing, then we need to check that this
+ * css_set points to the new cgroup; if it's any other
+ * hierarchy, then this css_set should point to the
+ * same cgroup as the old css_set.
+ */
+ if (cg1->root == new_cgrp->root) {
+ if (cg1 != new_cgrp)
+ return false;
+ } else {
+ if (cg1 != cg2)
+ return false;
+ }
+ }
+ return true;
+}
+
/*
* find_existing_css_set() is a helper for
* find_css_set(), and checks to see whether an existing
hhead = css_set_hash(template);
hlist_for_each_entry(cg, node, hhead, hlist) {
- if (!memcmp(template, cg->subsys, sizeof(cg->subsys))) {
- /* All subsystems matched */
- return cg;
- }
+ if (!compare_css_sets(cg, oldcg, cgrp, template))
+ continue;
+
+ /* This css_set matches what we need */
+ return cg;
}
/* No existing cgroup group matched */
link = list_first_entry(tmp_cg_links, struct cg_cgroup_link,
cgrp_link_list);
link->cg = cg;
+ link->cgrp = cgrp;
+ atomic_inc(&cgrp->count);
list_move(&link->cgrp_link_list, &cgrp->css_sets);
- list_add(&link->cg_link_list, &cg->cg_links);
+ /*
+ * Always add links to the tail of the list so that the list
+ * is sorted by order of hierarchy creation
+ */
+ list_add_tail(&link->cg_link_list, &cg->cg_links);
}
/*
{
struct css_set *res;
struct cgroup_subsys_state *template[CGROUP_SUBSYS_COUNT];
- int i;
struct list_head tmp_cg_links;
struct hlist_head *hhead;
+ struct cg_cgroup_link *link;
/* First see if we already have a cgroup group that matches
* the desired set */
write_lock(&css_set_lock);
/* Add reference counts and links from the new css_set. */
- for (i = 0; i < CGROUP_SUBSYS_COUNT; i++) {
- struct cgroup *cgrp = res->subsys[i]->cgroup;
- struct cgroup_subsys *ss = subsys[i];
- atomic_inc(&cgrp->count);
- /*
- * We want to add a link once per cgroup, so we
- * only do it for the first subsystem in each
- * hierarchy
- */
- if (ss->root->subsys_list.next == &ss->sibling)
- link_css_set(&tmp_cg_links, res, cgrp);
+ list_for_each_entry(link, &oldcg->cg_links, cg_link_list) {
+ struct cgroup *c = link->cgrp;
+ if (c->root == cgrp->root)
+ c = cgrp;
+ link_css_set(&tmp_cg_links, res, c);
}
- if (list_empty(&rootnode.subsys_list))
- link_css_set(&tmp_cg_links, res, dummytop);
BUG_ON(!list_empty(&tmp_cg_links));
return res;
}
+/*
+ * Return the cgroup for "task" from the given hierarchy. Must be
+ * called with cgroup_mutex held.
+ */
+static struct cgroup *task_cgroup_from_root(struct task_struct *task,
+ struct cgroupfs_root *root)
+{
+ struct css_set *css;
+ struct cgroup *res = NULL;
+
+ BUG_ON(!mutex_is_locked(&cgroup_mutex));
+ read_lock(&css_set_lock);
+ /*
+ * No need to lock the task - since we hold cgroup_mutex the
+ * task can't change groups, so the only thing that can happen
+ * is that it exits and its css is set back to init_css_set.
+ */
+ css = task->cgroups;
+ if (css == &init_css_set) {
+ res = &root->top_cgroup;
+ } else {
+ struct cg_cgroup_link *link;
+ list_for_each_entry(link, &css->cg_links, cg_link_list) {
+ struct cgroup *c = link->cgrp;
+ if (c->root == root) {
+ res = c;
+ break;
+ }
+ }
+ }
+ read_unlock(&css_set_lock);
+ BUG_ON(!res);
+ return res;
+}
+
/*
* There is one global cgroup mutex. We also require taking
* task_lock() when dereferencing a task's cgroup subsys pointers.
static int cgroup_rmdir(struct inode *unused_dir, struct dentry *dentry);
static int cgroup_populate_dir(struct cgroup *cgrp);
static const struct inode_operations cgroup_dir_inode_operations;
-static struct file_operations proc_cgroupstats_operations;
+static const struct file_operations proc_cgroupstats_operations;
static struct backing_dev_info cgroup_backing_dev_info = {
.name = "cgroup",
*/
deactivate_super(cgrp->root->sb);
+ /*
+ * if we're getting rid of the cgroup, refcount should ensure
+ * that there are no pidlists left.
+ */
+ BUG_ON(!list_empty(&cgrp->pidlists));
+
call_rcu(&cgrp->rcu_head, free_cgroup_rcu);
}
iput(inode);
seq_puts(seq, ",noprefix");
if (strlen(root->release_agent_path))
seq_printf(seq, ",release_agent=%s", root->release_agent_path);
+ if (strlen(root->name))
+ seq_printf(seq, ",name=%s", root->name);
mutex_unlock(&cgroup_mutex);
return 0;
}
unsigned long subsys_bits;
unsigned long flags;
char *release_agent;
+ char *name;
+ /* User explicitly requested empty subsystem */
+ bool none;
+
+ struct cgroupfs_root *new_root;
+
};
/* Convert a hierarchy specifier into a bitmask of subsystems and
mask = ~(1UL << cpuset_subsys_id);
#endif
- opts->subsys_bits = 0;
- opts->flags = 0;
- opts->release_agent = NULL;
+ memset(opts, 0, sizeof(*opts));
while ((token = strsep(&o, ",")) != NULL) {
if (!*token)
if (!ss->disabled)
opts->subsys_bits |= 1ul << i;
}
+ } else if (!strcmp(token, "none")) {
+ /* Explicitly have no subsystems */
+ opts->none = true;
} else if (!strcmp(token, "noprefix")) {
set_bit(ROOT_NOPREFIX, &opts->flags);
} else if (!strncmp(token, "release_agent=", 14)) {
/* Specifying two release agents is forbidden */
if (opts->release_agent)
return -EINVAL;
- opts->release_agent = kzalloc(PATH_MAX, GFP_KERNEL);
+ opts->release_agent =
+ kstrndup(token + 14, PATH_MAX, GFP_KERNEL);
if (!opts->release_agent)
return -ENOMEM;
- strncpy(opts->release_agent, token + 14, PATH_MAX - 1);
- opts->release_agent[PATH_MAX - 1] = 0;
+ } else if (!strncmp(token, "name=", 5)) {
+ int i;
+ const char *name = token + 5;
+ /* Can't specify an empty name */
+ if (!strlen(name))
+ return -EINVAL;
+ /* Must match [\w.-]+ */
+ for (i = 0; i < strlen(name); i++) {
+ char c = name[i];
+ if (isalnum(c))
+ continue;
+ if ((c == '.') || (c == '-') || (c == '_'))
+ continue;
+ return -EINVAL;
+ }
+ /* Specifying two names is forbidden */
+ if (opts->name)
+ return -EINVAL;
+ opts->name = kstrndup(name,
+ MAX_CGROUP_ROOT_NAMELEN,
+ GFP_KERNEL);
+ if (!opts->name)
+ return -ENOMEM;
} else {
struct cgroup_subsys *ss;
int i;
}
}
+ /* Consistency checks */
+
/*
* Option noprefix was introduced just for backward compatibility
* with the old cpuset, so we allow noprefix only if mounting just
(opts->subsys_bits & mask))
return -EINVAL;
- /* We can't have an empty hierarchy */
- if (!opts->subsys_bits)
+
+ /* Can't specify "none" and some subsystems */
+ if (opts->subsys_bits && opts->none)
+ return -EINVAL;
+
+ /*
+ * We either have to specify by name or by subsystems. (So all
+ * empty hierarchies must have a name).
+ */
+ if (!opts->subsys_bits && !opts->name)
return -EINVAL;
return 0;
goto out_unlock;
}
+ /* Don't allow name to change at remount */
+ if (opts.name && strcmp(opts.name, root->name)) {
+ ret = -EINVAL;
+ goto out_unlock;
+ }
+
ret = rebind_subsystems(root, opts.subsys_bits);
if (ret)
goto out_unlock;
strcpy(root->release_agent_path, opts.release_agent);
out_unlock:
kfree(opts.release_agent);
+ kfree(opts.name);
mutex_unlock(&cgroup_mutex);
mutex_unlock(&cgrp->dentry->d_inode->i_mutex);
unlock_kernel();
INIT_LIST_HEAD(&cgrp->children);
INIT_LIST_HEAD(&cgrp->css_sets);
INIT_LIST_HEAD(&cgrp->release_list);
- INIT_LIST_HEAD(&cgrp->pids_list);
- init_rwsem(&cgrp->pids_mutex);
+ INIT_LIST_HEAD(&cgrp->pidlists);
+ mutex_init(&cgrp->pidlist_mutex);
}
+
static void init_cgroup_root(struct cgroupfs_root *root)
{
struct cgroup *cgrp = &root->top_cgroup;
init_cgroup_housekeeping(cgrp);
}
+static bool init_root_id(struct cgroupfs_root *root)
+{
+ int ret = 0;
+
+ do {
+ if (!ida_pre_get(&hierarchy_ida, GFP_KERNEL))
+ return false;
+ spin_lock(&hierarchy_id_lock);
+ /* Try to allocate the next unused ID */
+ ret = ida_get_new_above(&hierarchy_ida, next_hierarchy_id,
+ &root->hierarchy_id);
+ if (ret == -ENOSPC)
+ /* Try again starting from 0 */
+ ret = ida_get_new(&hierarchy_ida, &root->hierarchy_id);
+ if (!ret) {
+ next_hierarchy_id = root->hierarchy_id + 1;
+ } else if (ret != -EAGAIN) {
+ /* Can only get here if the 31-bit IDR is full ... */
+ BUG_ON(ret);
+ }
+ spin_unlock(&hierarchy_id_lock);
+ } while (ret);
+ return true;
+}
+
static int cgroup_test_super(struct super_block *sb, void *data)
{
- struct cgroupfs_root *new = data;
+ struct cgroup_sb_opts *opts = data;
struct cgroupfs_root *root = sb->s_fs_info;
- /* First check subsystems */
- if (new->subsys_bits != root->subsys_bits)
- return 0;
+ /* If we asked for a name then it must match */
+ if (opts->name && strcmp(opts->name, root->name))
+ return 0;
- /* Next check flags */
- if (new->flags != root->flags)
+ /*
+ * If we asked for subsystems (or explicitly for no
+ * subsystems) then they must match
+ */
+ if ((opts->subsys_bits || opts->none)
+ && (opts->subsys_bits != root->subsys_bits))
return 0;
return 1;
}
+static struct cgroupfs_root *cgroup_root_from_opts(struct cgroup_sb_opts *opts)
+{
+ struct cgroupfs_root *root;
+
+ if (!opts->subsys_bits && !opts->none)
+ return NULL;
+
+ root = kzalloc(sizeof(*root), GFP_KERNEL);
+ if (!root)
+ return ERR_PTR(-ENOMEM);
+
+ if (!init_root_id(root)) {
+ kfree(root);
+ return ERR_PTR(-ENOMEM);
+ }
+ init_cgroup_root(root);
+
+ root->subsys_bits = opts->subsys_bits;
+ root->flags = opts->flags;
+ if (opts->release_agent)
+ strcpy(root->release_agent_path, opts->release_agent);
+ if (opts->name)
+ strcpy(root->name, opts->name);
+ return root;
+}
+
+static void cgroup_drop_root(struct cgroupfs_root *root)
+{
+ if (!root)
+ return;
+
+ BUG_ON(!root->hierarchy_id);
+ spin_lock(&hierarchy_id_lock);
+ ida_remove(&hierarchy_ida, root->hierarchy_id);
+ spin_unlock(&hierarchy_id_lock);
+ kfree(root);
+}
+
static int cgroup_set_super(struct super_block *sb, void *data)
{
int ret;
- struct cgroupfs_root *root = data;
+ struct cgroup_sb_opts *opts = data;
+
+ /* If we don't have a new root, we can't set up a new sb */
+ if (!opts->new_root)
+ return -EINVAL;
+
+ BUG_ON(!opts->subsys_bits && !opts->none);
ret = set_anon_super(sb, NULL);
if (ret)
return ret;
- sb->s_fs_info = root;
- root->sb = sb;
+ sb->s_fs_info = opts->new_root;
+ opts->new_root->sb = sb;
sb->s_blocksize = PAGE_CACHE_SIZE;
sb->s_blocksize_bits = PAGE_CACHE_SHIFT;
void *data, struct vfsmount *mnt)
{
struct cgroup_sb_opts opts;
+ struct cgroupfs_root *root;
int ret = 0;
struct super_block *sb;
- struct cgroupfs_root *root;
- struct list_head tmp_cg_links;
+ struct cgroupfs_root *new_root;
/* First find the desired set of subsystems */
ret = parse_cgroupfs_options(data, &opts);
- if (ret) {
- kfree(opts.release_agent);
- return ret;
- }
-
- root = kzalloc(sizeof(*root), GFP_KERNEL);
- if (!root) {
- kfree(opts.release_agent);
- return -ENOMEM;
- }
+ if (ret)
+ goto out_err;
- init_cgroup_root(root);
- root->subsys_bits = opts.subsys_bits;
- root->flags = opts.flags;
- if (opts.release_agent) {
- strcpy(root->release_agent_path, opts.release_agent);
- kfree(opts.release_agent);
+ /*
+ * Allocate a new cgroup root. We may not need it if we're
+ * reusing an existing hierarchy.
+ */
+ new_root = cgroup_root_from_opts(&opts);
+ if (IS_ERR(new_root)) {
+ ret = PTR_ERR(new_root);
+ goto out_err;
}
+ opts.new_root = new_root;
- sb = sget(fs_type, cgroup_test_super, cgroup_set_super, root);
-
+ /* Locate an existing or new sb for this hierarchy */
+ sb = sget(fs_type, cgroup_test_super, cgroup_set_super, &opts);
if (IS_ERR(sb)) {
- kfree(root);
- return PTR_ERR(sb);
+ ret = PTR_ERR(sb);
+ cgroup_drop_root(opts.new_root);
+ goto out_err;
}
- if (sb->s_fs_info != root) {
- /* Reusing an existing superblock */
- BUG_ON(sb->s_root == NULL);
- kfree(root);
- root = NULL;
- } else {
- /* New superblock */
+ root = sb->s_fs_info;
+ BUG_ON(!root);
+ if (root == opts.new_root) {
+ /* We used the new root structure, so this is a new hierarchy */
+ struct list_head tmp_cg_links;
struct cgroup *root_cgrp = &root->top_cgroup;
struct inode *inode;
+ struct cgroupfs_root *existing_root;
int i;
BUG_ON(sb->s_root != NULL);
mutex_lock(&inode->i_mutex);
mutex_lock(&cgroup_mutex);
+ if (strlen(root->name)) {
+ /* Check for name clashes with existing mounts */
+ for_each_active_root(existing_root) {
+ if (!strcmp(existing_root->name, root->name)) {
+ ret = -EBUSY;
+ mutex_unlock(&cgroup_mutex);
+ mutex_unlock(&inode->i_mutex);
+ goto drop_new_super;
+ }
+ }
+ }
+
/*
* We're accessing css_set_count without locking
* css_set_lock here, but that's OK - it can only be
if (ret == -EBUSY) {
mutex_unlock(&cgroup_mutex);
mutex_unlock(&inode->i_mutex);
- goto free_cg_links;
+ free_cg_links(&tmp_cg_links);
+ goto drop_new_super;
}
/* EBUSY should be the only error here */
BUG_ON(root->number_of_cgroups != 1);
cgroup_populate_dir(root_cgrp);
- mutex_unlock(&inode->i_mutex);
mutex_unlock(&cgroup_mutex);
+ mutex_unlock(&inode->i_mutex);
+ } else {
+ /*
+ * We re-used an existing hierarchy - the new root (if
+ * any) is not needed
+ */
+ cgroup_drop_root(opts.new_root);
}
simple_set_mnt(mnt, sb);
+ kfree(opts.release_agent);
+ kfree(opts.name);
return 0;
- free_cg_links:
- free_cg_links(&tmp_cg_links);
drop_new_super:
deactivate_locked_super(sb);
+ out_err:
+ kfree(opts.release_agent);
+ kfree(opts.name);
+
return ret;
}
mutex_unlock(&cgroup_mutex);
kill_litter_super(sb);
- kfree(root);
+ cgroup_drop_root(root);
}
static struct file_system_type cgroup_fs_type = {
return 0;
}
-/*
- * Return the first subsystem attached to a cgroup's hierarchy, and
- * its subsystem id.
- */
-
-static void get_first_subsys(const struct cgroup *cgrp,
- struct cgroup_subsys_state **css, int *subsys_id)
-{
- const struct cgroupfs_root *root = cgrp->root;
- const struct cgroup_subsys *test_ss;
- BUG_ON(list_empty(&root->subsys_list));
- test_ss = list_entry(root->subsys_list.next,
- struct cgroup_subsys, sibling);
- if (css) {
- *css = cgrp->subsys[test_ss->subsys_id];
- BUG_ON(!*css);
- }
- if (subsys_id)
- *subsys_id = test_ss->subsys_id;
-}
-
/**
* cgroup_attach_task - attach task 'tsk' to cgroup 'cgrp'
* @cgrp: the cgroup the task is attaching to
struct css_set *cg;
struct css_set *newcg;
struct cgroupfs_root *root = cgrp->root;
- int subsys_id;
-
- get_first_subsys(cgrp, NULL, &subsys_id);
/* Nothing to do if the task is already in that cgroup */
- oldcgrp = task_cgroup(tsk, subsys_id);
+ oldcgrp = task_cgroup_from_root(tsk, root);
if (cgrp == oldcgrp)
return 0;
for_each_subsys(root, ss) {
if (ss->can_attach) {
- retval = ss->can_attach(ss, cgrp, tsk);
+ retval = ss->can_attach(ss, cgrp, tsk, false);
if (retval)
return retval;
}
for_each_subsys(root, ss) {
if (ss->attach)
- ss->attach(ss, cgrp, oldcgrp, tsk);
+ ss->attach(ss, cgrp, oldcgrp, tsk, false);
}
set_bit(CGRP_RELEASABLE, &oldcgrp->flags);
synchronize_rcu();
return ret;
}
-/* The various types of files and directories in a cgroup file system */
-enum cgroup_filetype {
- FILE_ROOT,
- FILE_DIR,
- FILE_TASKLIST,
- FILE_NOTIFY_ON_RELEASE,
- FILE_RELEASE_AGENT,
-};
-
/**
* cgroup_lock_live_group - take cgroup_mutex and check that cgrp is alive.
* @cgrp: the cgroup to be checked for liveness
return single_release(inode, file);
}
-static struct file_operations cgroup_seqfile_operations = {
+static const struct file_operations cgroup_seqfile_operations = {
.read = seq_read,
.write = cgroup_file_write,
.llseek = seq_lseek,
return simple_rename(old_dir, old_dentry, new_dir, new_dentry);
}
-static struct file_operations cgroup_file_operations = {
+static const struct file_operations cgroup_file_operations = {
.read = cgroup_file_read,
.write = cgroup_file_write,
.llseek = generic_file_llseek,
* the start of a css_set
*/
static void cgroup_advance_iter(struct cgroup *cgrp,
- struct cgroup_iter *it)
+ struct cgroup_iter *it)
{
struct list_head *l = it->cg_link;
struct cg_cgroup_link *link;
}
/*
- * Stuff for reading the 'tasks' file.
+ * Stuff for reading the 'tasks'/'procs' files.
*
* Reading this file can return large amounts of data if a cgroup has
* *lots* of attached tasks. So it may need several calls to read(),
*/
/*
- * Load into 'pidarray' up to 'npids' of the tasks using cgroup
- * 'cgrp'. Return actual number of pids loaded. No need to
- * task_lock(p) when reading out p->cgroup, since we're in an RCU
- * read section, so the css_set can't go away, and is
- * immutable after creation.
+ * The following two functions "fix" the issue where there are more pids
+ * than kmalloc will give memory for; in such cases, we use vmalloc/vfree.
+ * TODO: replace with a kernel-wide solution to this problem
+ */
+#define PIDLIST_TOO_LARGE(c) ((c) * sizeof(pid_t) > (PAGE_SIZE * 2))
+static void *pidlist_allocate(int count)
+{
+ if (PIDLIST_TOO_LARGE(count))
+ return vmalloc(count * sizeof(pid_t));
+ else
+ return kmalloc(count * sizeof(pid_t), GFP_KERNEL);
+}
+static void pidlist_free(void *p)
+{
+ if (is_vmalloc_addr(p))
+ vfree(p);
+ else
+ kfree(p);
+}
+static void *pidlist_resize(void *p, int newcount)
+{
+ void *newlist;
+ /* note: if new alloc fails, old p will still be valid either way */
+ if (is_vmalloc_addr(p)) {
+ newlist = vmalloc(newcount * sizeof(pid_t));
+ if (!newlist)
+ return NULL;
+ memcpy(newlist, p, newcount * sizeof(pid_t));
+ vfree(p);
+ } else {
+ newlist = krealloc(p, newcount * sizeof(pid_t), GFP_KERNEL);
+ }
+ return newlist;
+}
+
+/*
+ * pidlist_uniq - given a kmalloc()ed list, strip out all duplicate entries
+ * If the new stripped list is sufficiently smaller and there's enough memory
+ * to allocate a new buffer, will let go of the unneeded memory. Returns the
+ * number of unique elements.
+ */
+/* is the size difference enough that we should re-allocate the array? */
+#define PIDLIST_REALLOC_DIFFERENCE(old, new) ((old) - PAGE_SIZE >= (new))
+static int pidlist_uniq(pid_t **p, int length)
+{
+ int src, dest = 1;
+ pid_t *list = *p;
+ pid_t *newlist;
+
+ /*
+ * we presume the 0th element is unique, so i starts at 1. trivial
+ * edge cases first; no work needs to be done for either
+ */
+ if (length == 0 || length == 1)
+ return length;
+ /* src and dest walk down the list; dest counts unique elements */
+ for (src = 1; src < length; src++) {
+ /* find next unique element */
+ while (list[src] == list[src-1]) {
+ src++;
+ if (src == length)
+ goto after;
+ }
+ /* dest always points to where the next unique element goes */
+ list[dest] = list[src];
+ dest++;
+ }
+after:
+ /*
+ * if the length difference is large enough, we want to allocate a
+ * smaller buffer to save memory. if this fails due to out of memory,
+ * we'll just stay with what we've got.
+ */
+ if (PIDLIST_REALLOC_DIFFERENCE(length, dest)) {
+ newlist = pidlist_resize(list, dest);
+ if (newlist)
+ *p = newlist;
+ }
+ return dest;
+}
+
+static int cmppid(const void *a, const void *b)
+{
+ return *(pid_t *)a - *(pid_t *)b;
+}
+
+/*
+ * find the appropriate pidlist for our purpose (given procs vs tasks)
+ * returns with the lock on that pidlist already held, and takes care
+ * of the use count, or returns NULL with no locks held if we're out of
+ * memory.
*/
-static int pid_array_load(pid_t *pidarray, int npids, struct cgroup *cgrp)
+static struct cgroup_pidlist *cgroup_pidlist_find(struct cgroup *cgrp,
+ enum cgroup_filetype type)
{
- int n = 0, pid;
+ struct cgroup_pidlist *l;
+ /* don't need task_nsproxy() if we're looking at ourself */
+ struct pid_namespace *ns = get_pid_ns(current->nsproxy->pid_ns);
+ /*
+ * We can't drop the pidlist_mutex before taking the l->mutex in case
+ * the last ref-holder is trying to remove l from the list at the same
+ * time. Holding the pidlist_mutex precludes somebody taking whichever
+ * list we find out from under us - compare release_pid_array().
+ */
+ mutex_lock(&cgrp->pidlist_mutex);
+ list_for_each_entry(l, &cgrp->pidlists, links) {
+ if (l->key.type == type && l->key.ns == ns) {
+ /* found a matching list - drop the extra refcount */
+ put_pid_ns(ns);
+ /* make sure l doesn't vanish out from under us */
+ down_write(&l->mutex);
+ mutex_unlock(&cgrp->pidlist_mutex);
+ l->use_count++;
+ return l;
+ }
+ }
+ /* entry not found; create a new one */
+ l = kmalloc(sizeof(struct cgroup_pidlist), GFP_KERNEL);
+ if (!l) {
+ mutex_unlock(&cgrp->pidlist_mutex);
+ put_pid_ns(ns);
+ return l;
+ }
+ init_rwsem(&l->mutex);
+ down_write(&l->mutex);
+ l->key.type = type;
+ l->key.ns = ns;
+ l->use_count = 0; /* don't increment here */
+ l->list = NULL;
+ l->owner = cgrp;
+ list_add(&l->links, &cgrp->pidlists);
+ mutex_unlock(&cgrp->pidlist_mutex);
+ return l;
+}
+
+/*
+ * Load a cgroup's pidarray with either procs' tgids or tasks' pids
+ */
+static int pidlist_array_load(struct cgroup *cgrp, enum cgroup_filetype type,
+ struct cgroup_pidlist **lp)
+{
+ pid_t *array;
+ int length;
+ int pid, n = 0; /* used for populating the array */
struct cgroup_iter it;
struct task_struct *tsk;
+ struct cgroup_pidlist *l;
+
+ /*
+ * If cgroup gets more users after we read count, we won't have
+ * enough space - tough. This race is indistinguishable to the
+ * caller from the case that the additional cgroup users didn't
+ * show up until sometime later on.
+ */
+ length = cgroup_task_count(cgrp);
+ array = pidlist_allocate(length);
+ if (!array)
+ return -ENOMEM;
+ /* now, populate the array */
cgroup_iter_start(cgrp, &it);
while ((tsk = cgroup_iter_next(cgrp, &it))) {
- if (unlikely(n == npids))
+ if (unlikely(n == length))
break;
- pid = task_pid_vnr(tsk);
- if (pid > 0)
- pidarray[n++] = pid;
+ /* get tgid or pid for procs or tasks file respectively */
+ if (type == CGROUP_FILE_PROCS)
+ pid = task_tgid_vnr(tsk);
+ else
+ pid = task_pid_vnr(tsk);
+ if (pid > 0) /* make sure to only use valid results */
+ array[n++] = pid;
}
cgroup_iter_end(cgrp, &it);
- return n;
+ length = n;
+ /* now sort & (if procs) strip out duplicates */
+ sort(array, length, sizeof(pid_t), cmppid, NULL);
+ if (type == CGROUP_FILE_PROCS)
+ length = pidlist_uniq(&array, length);
+ l = cgroup_pidlist_find(cgrp, type);
+ if (!l) {
+ pidlist_free(array);
+ return -ENOMEM;
+ }
+ /* store array, freeing old if necessary - lock already held */
+ pidlist_free(l->list);
+ l->list = array;
+ l->length = length;
+ l->use_count++;
+ up_write(&l->mutex);
+ *lp = l;
+ return 0;
}
/**
return ret;
}
-/*
- * Cache pids for all threads in the same pid namespace that are
- * opening the same "tasks" file.
- */
-struct cgroup_pids {
- /* The node in cgrp->pids_list */
- struct list_head list;
- /* The cgroup those pids belong to */
- struct cgroup *cgrp;
- /* The namepsace those pids belong to */
- struct pid_namespace *ns;
- /* Array of process ids in the cgroup */
- pid_t *tasks_pids;
- /* How many files are using the this tasks_pids array */
- int use_count;
- /* Length of the current tasks_pids array */
- int length;
-};
-
-static int cmppid(const void *a, const void *b)
-{
- return *(pid_t *)a - *(pid_t *)b;
-}
/*
- * seq_file methods for the "tasks" file. The seq_file position is the
+ * seq_file methods for the tasks/procs files. The seq_file position is the
* next pid to display; the seq_file iterator is a pointer to the pid
- * in the cgroup->tasks_pids array.
+ * in the cgroup->l->list array.
*/
-static void *cgroup_tasks_start(struct seq_file *s, loff_t *pos)
+static void *cgroup_pidlist_start(struct seq_file *s, loff_t *pos)
{
/*
* Initially we receive a position value that corresponds to
* after a seek to the start). Use a binary-search to find the
* next pid to display, if any
*/
- struct cgroup_pids *cp = s->private;
- struct cgroup *cgrp = cp->cgrp;
+ struct cgroup_pidlist *l = s->private;
int index = 0, pid = *pos;
int *iter;
- down_read(&cgrp->pids_mutex);
+ down_read(&l->mutex);
if (pid) {
- int end = cp->length;
+ int end = l->length;
while (index < end) {
int mid = (index + end) / 2;
- if (cp->tasks_pids[mid] == pid) {
+ if (l->list[mid] == pid) {
index = mid;
break;
- } else if (cp->tasks_pids[mid] <= pid)
+ } else if (l->list[mid] <= pid)
index = mid + 1;
else
end = mid;
}
}
/* If we're off the end of the array, we're done */
- if (index >= cp->length)
+ if (index >= l->length)
return NULL;
/* Update the abstract position to be the actual pid that we found */
- iter = cp->tasks_pids + index;
+ iter = l->list + index;
*pos = *iter;
return iter;
}
-static void cgroup_tasks_stop(struct seq_file *s, void *v)
+static void cgroup_pidlist_stop(struct seq_file *s, void *v)
{
- struct cgroup_pids *cp = s->private;
- struct cgroup *cgrp = cp->cgrp;
- up_read(&cgrp->pids_mutex);
+ struct cgroup_pidlist *l = s->private;
+ up_read(&l->mutex);
}
-static void *cgroup_tasks_next(struct seq_file *s, void *v, loff_t *pos)
+static void *cgroup_pidlist_next(struct seq_file *s, void *v, loff_t *pos)
{
- struct cgroup_pids *cp = s->private;
- int *p = v;
- int *end = cp->tasks_pids + cp->length;
-
+ struct cgroup_pidlist *l = s->private;
+ pid_t *p = v;
+ pid_t *end = l->list + l->length;
/*
* Advance to the next pid in the array. If this goes off the
* end, we're done
}
}
-static int cgroup_tasks_show(struct seq_file *s, void *v)
+static int cgroup_pidlist_show(struct seq_file *s, void *v)
{
return seq_printf(s, "%d\n", *(int *)v);
}
-static const struct seq_operations cgroup_tasks_seq_operations = {
- .start = cgroup_tasks_start,
- .stop = cgroup_tasks_stop,
- .next = cgroup_tasks_next,
- .show = cgroup_tasks_show,
+/*
+ * seq_operations functions for iterating on pidlists through seq_file -
+ * independent of whether it's tasks or procs
+ */
+static const struct seq_operations cgroup_pidlist_seq_operations = {
+ .start = cgroup_pidlist_start,
+ .stop = cgroup_pidlist_stop,
+ .next = cgroup_pidlist_next,
+ .show = cgroup_pidlist_show,
};
-static void release_cgroup_pid_array(struct cgroup_pids *cp)
+static void cgroup_release_pid_array(struct cgroup_pidlist *l)
{
- struct cgroup *cgrp = cp->cgrp;
-
- down_write(&cgrp->pids_mutex);
- BUG_ON(!cp->use_count);
- if (!--cp->use_count) {
- list_del(&cp->list);
- put_pid_ns(cp->ns);
- kfree(cp->tasks_pids);
- kfree(cp);
+ /*
+ * the case where we're the last user of this particular pidlist will
+ * have us remove it from the cgroup's list, which entails taking the
+ * mutex. since in pidlist_find the pidlist->lock depends on cgroup->
+ * pidlist_mutex, we have to take pidlist_mutex first.
+ */
+ mutex_lock(&l->owner->pidlist_mutex);
+ down_write(&l->mutex);
+ BUG_ON(!l->use_count);
+ if (!--l->use_count) {
+ /* we're the last user if refcount is 0; remove and free */
+ list_del(&l->links);
+ mutex_unlock(&l->owner->pidlist_mutex);
+ pidlist_free(l->list);
+ put_pid_ns(l->key.ns);
+ up_write(&l->mutex);
+ kfree(l);
+ return;
}
- up_write(&cgrp->pids_mutex);
+ mutex_unlock(&l->owner->pidlist_mutex);
+ up_write(&l->mutex);
}
-static int cgroup_tasks_release(struct inode *inode, struct file *file)
+static int cgroup_pidlist_release(struct inode *inode, struct file *file)
{
- struct seq_file *seq;
- struct cgroup_pids *cp;
-
+ struct cgroup_pidlist *l;
if (!(file->f_mode & FMODE_READ))
return 0;
-
- seq = file->private_data;
- cp = seq->private;
-
- release_cgroup_pid_array(cp);
+ /*
+ * the seq_file will only be initialized if the file was opened for
+ * reading; hence we check if it's not null only in that case.
+ */
+ l = ((struct seq_file *)file->private_data)->private;
+ cgroup_release_pid_array(l);
return seq_release(inode, file);
}
-static struct file_operations cgroup_tasks_operations = {
+static const struct file_operations cgroup_pidlist_operations = {
.read = seq_read,
.llseek = seq_lseek,
.write = cgroup_file_write,
- .release = cgroup_tasks_release,
+ .release = cgroup_pidlist_release,
};
/*
- * Handle an open on 'tasks' file. Prepare an array containing the
- * process id's of tasks currently attached to the cgroup being opened.
+ * The following functions handle opens on a file that displays a pidlist
+ * (tasks or procs). Prepare an array of the process/thread IDs of whoever's
+ * in the cgroup.
*/
-
-static int cgroup_tasks_open(struct inode *unused, struct file *file)
+/* helper function for the two below it */
+static int cgroup_pidlist_open(struct file *file, enum cgroup_filetype type)
{
struct cgroup *cgrp = __d_cgrp(file->f_dentry->d_parent);
- struct pid_namespace *ns = current->nsproxy->pid_ns;
- struct cgroup_pids *cp;
- pid_t *pidarray;
- int npids;
+ struct cgroup_pidlist *l;
int retval;
/* Nothing to do for write-only files */
if (!(file->f_mode & FMODE_READ))
return 0;
- /*
- * If cgroup gets more users after we read count, we won't have
- * enough space - tough. This race is indistinguishable to the
- * caller from the case that the additional cgroup users didn't
- * show up until sometime later on.
- */
- npids = cgroup_task_count(cgrp);
- pidarray = kmalloc(npids * sizeof(pid_t), GFP_KERNEL);
- if (!pidarray)
- return -ENOMEM;
- npids = pid_array_load(pidarray, npids, cgrp);
- sort(pidarray, npids, sizeof(pid_t), cmppid, NULL);
-
- /*
- * Store the array in the cgroup, freeing the old
- * array if necessary
- */
- down_write(&cgrp->pids_mutex);
-
- list_for_each_entry(cp, &cgrp->pids_list, list) {
- if (ns == cp->ns)
- goto found;
- }
-
- cp = kzalloc(sizeof(*cp), GFP_KERNEL);
- if (!cp) {
- up_write(&cgrp->pids_mutex);
- kfree(pidarray);
- return -ENOMEM;
- }
- cp->cgrp = cgrp;
- cp->ns = ns;
- get_pid_ns(ns);
- list_add(&cp->list, &cgrp->pids_list);
-found:
- kfree(cp->tasks_pids);
- cp->tasks_pids = pidarray;
- cp->length = npids;
- cp->use_count++;
- up_write(&cgrp->pids_mutex);
-
- file->f_op = &cgroup_tasks_operations;
+ /* have the array populated */
+ retval = pidlist_array_load(cgrp, type, &l);
+ if (retval)
+ return retval;
+ /* configure file information */
+ file->f_op = &cgroup_pidlist_operations;
- retval = seq_open(file, &cgroup_tasks_seq_operations);
+ retval = seq_open(file, &cgroup_pidlist_seq_operations);
if (retval) {
- release_cgroup_pid_array(cp);
+ cgroup_release_pid_array(l);
return retval;
}
- ((struct seq_file *)file->private_data)->private = cp;
+ ((struct seq_file *)file->private_data)->private = l;
return 0;
}
+static int cgroup_tasks_open(struct inode *unused, struct file *file)
+{
+ return cgroup_pidlist_open(file, CGROUP_FILE_TASKS);
+}
+static int cgroup_procs_open(struct inode *unused, struct file *file)
+{
+ return cgroup_pidlist_open(file, CGROUP_FILE_PROCS);
+}
static u64 cgroup_read_notify_on_release(struct cgroup *cgrp,
struct cftype *cft)
/*
* for the common functions, 'private' gives the type of file
*/
+/* for hysterical raisins, we can't put this on the older files */
+#define CGROUP_FILE_GENERIC_PREFIX "cgroup."
static struct cftype files[] = {
{
.name = "tasks",
.open = cgroup_tasks_open,
.write_u64 = cgroup_tasks_write,
- .release = cgroup_tasks_release,
- .private = FILE_TASKLIST,
+ .release = cgroup_pidlist_release,
.mode = S_IRUGO | S_IWUSR,
},
-
+ {
+ .name = CGROUP_FILE_GENERIC_PREFIX "procs",
+ .open = cgroup_procs_open,
+ /* .write_u64 = cgroup_procs_write, TODO */
+ .release = cgroup_pidlist_release,
+ .mode = S_IRUGO,
+ },
{
.name = "notify_on_release",
.read_u64 = cgroup_read_notify_on_release,
.write_u64 = cgroup_write_notify_on_release,
- .private = FILE_NOTIFY_ON_RELEASE,
},
};
.read_seq_string = cgroup_release_agent_show,
.write_string = cgroup_release_agent_write,
.max_write_len = PATH_MAX,
- .private = FILE_RELEASE_AGENT,
};
static int cgroup_populate_dir(struct cgroup *cgrp)
init_task.cgroups = &init_css_set;
init_css_set_link.cg = &init_css_set;
+ init_css_set_link.cgrp = dummytop;
list_add(&init_css_set_link.cgrp_link_list,
&rootnode.top_cgroup.css_sets);
list_add(&init_css_set_link.cg_link_list,
/* Add init_css_set to the hash table */
hhead = css_set_hash(init_css_set.subsys);
hlist_add_head(&init_css_set.hlist, hhead);
-
+ BUG_ON(!init_root_id(&rootnode));
err = register_filesystem(&cgroup_fs_type);
if (err < 0)
goto out;
for_each_active_root(root) {
struct cgroup_subsys *ss;
struct cgroup *cgrp;
- int subsys_id;
int count = 0;
- seq_printf(m, "%lu:", root->subsys_bits);
+ seq_printf(m, "%d:", root->hierarchy_id);
for_each_subsys(root, ss)
seq_printf(m, "%s%s", count++ ? "," : "", ss->name);
+ if (strlen(root->name))
+ seq_printf(m, "%sname=%s", count ? "," : "",
+ root->name);
seq_putc(m, ':');
- get_first_subsys(&root->top_cgroup, NULL, &subsys_id);
- cgrp = task_cgroup(tsk, subsys_id);
+ cgrp = task_cgroup_from_root(tsk, root);
retval = cgroup_path(cgrp, buf, PAGE_SIZE);
if (retval < 0)
goto out_unlock;
return single_open(file, proc_cgroup_show, pid);
}
-struct file_operations proc_cgroup_operations = {
+const struct file_operations proc_cgroup_operations = {
.open = cgroup_open,
.read = seq_read,
.llseek = seq_lseek,
mutex_lock(&cgroup_mutex);
for (i = 0; i < CGROUP_SUBSYS_COUNT; i++) {
struct cgroup_subsys *ss = subsys[i];
- seq_printf(m, "%s\t%lu\t%d\t%d\n",
- ss->name, ss->root->subsys_bits,
+ seq_printf(m, "%s\t%d\t%d\t%d\n",
+ ss->name, ss->root->hierarchy_id,
ss->root->number_of_cgroups, !ss->disabled);
}
mutex_unlock(&cgroup_mutex);
return single_open(file, proc_cgroupstats_show, NULL);
}
-static struct file_operations proc_cgroupstats_operations = {
+static const struct file_operations proc_cgroupstats_operations = {
.open = cgroupstats_open,
.read = seq_read,
.llseek = seq_lseek,
{
int ret;
struct cgroup *target;
- int subsys_id;
if (cgrp == dummytop)
return 1;
- get_first_subsys(cgrp, NULL, &subsys_id);
- target = task_cgroup(task, subsys_id);
+ target = task_cgroup_from_root(task, cgrp->root);
while (cgrp != target && cgrp!= cgrp->top_cgroup)
cgrp = cgrp->parent;
ret = (cgrp == target);
void __css_put(struct cgroup_subsys_state *css)
{
struct cgroup *cgrp = css->cgroup;
+ int val;
rcu_read_lock();
- if (atomic_dec_return(&css->refcnt) == 1) {
+ val = atomic_dec_return(&css->refcnt);
+ if (val == 1) {
if (notify_on_release(cgrp)) {
set_bit(CGRP_RELEASABLE, &cgrp->flags);
check_for_release(cgrp);
cgroup_wakeup_rmdir_waiter(cgrp);
}
rcu_read_unlock();
+ WARN_ON_ONCE(val < 1);
}
/*
return ret;
}
+#ifdef CONFIG_CGROUP_DEBUG
+static struct cgroup_subsys_state *debug_create(struct cgroup_subsys *ss,
+ struct cgroup *cont)
+{
+ struct cgroup_subsys_state *css = kzalloc(sizeof(*css), GFP_KERNEL);
+
+ if (!css)
+ return ERR_PTR(-ENOMEM);
+
+ return css;
+}
+
+static void debug_destroy(struct cgroup_subsys *ss, struct cgroup *cont)
+{
+ kfree(cont->subsys[debug_subsys_id]);
+}
+
+static u64 cgroup_refcount_read(struct cgroup *cont, struct cftype *cft)
+{
+ return atomic_read(&cont->count);
+}
+
+static u64 debug_taskcount_read(struct cgroup *cont, struct cftype *cft)
+{
+ return cgroup_task_count(cont);
+}
+
+static u64 current_css_set_read(struct cgroup *cont, struct cftype *cft)
+{
+ return (u64)(unsigned long)current->cgroups;
+}
+
+static u64 current_css_set_refcount_read(struct cgroup *cont,
+ struct cftype *cft)
+{
+ u64 count;
+
+ rcu_read_lock();
+ count = atomic_read(¤t->cgroups->refcount);
+ rcu_read_unlock();
+ return count;
+}
+
+static int current_css_set_cg_links_read(struct cgroup *cont,
+ struct cftype *cft,
+ struct seq_file *seq)
+{
+ struct cg_cgroup_link *link;
+ struct css_set *cg;
+
+ read_lock(&css_set_lock);
+ rcu_read_lock();
+ cg = rcu_dereference(current->cgroups);
+ list_for_each_entry(link, &cg->cg_links, cg_link_list) {
+ struct cgroup *c = link->cgrp;
+ const char *name;
+
+ if (c->dentry)
+ name = c->dentry->d_name.name;
+ else
+ name = "?";
+ seq_printf(seq, "Root %d group %s\n",
+ c->root->hierarchy_id, name);
+ }
+ rcu_read_unlock();
+ read_unlock(&css_set_lock);
+ return 0;
+}
+
+#define MAX_TASKS_SHOWN_PER_CSS 25
+static int cgroup_css_links_read(struct cgroup *cont,
+ struct cftype *cft,
+ struct seq_file *seq)
+{
+ struct cg_cgroup_link *link;
+
+ read_lock(&css_set_lock);
+ list_for_each_entry(link, &cont->css_sets, cgrp_link_list) {
+ struct css_set *cg = link->cg;
+ struct task_struct *task;
+ int count = 0;
+ seq_printf(seq, "css_set %p\n", cg);
+ list_for_each_entry(task, &cg->tasks, cg_list) {
+ if (count++ > MAX_TASKS_SHOWN_PER_CSS) {
+ seq_puts(seq, " ...\n");
+ break;
+ } else {
+ seq_printf(seq, " task %d\n",
+ task_pid_vnr(task));
+ }
+ }
+ }
+ read_unlock(&css_set_lock);
+ return 0;
+}
+
+static u64 releasable_read(struct cgroup *cgrp, struct cftype *cft)
+{
+ return test_bit(CGRP_RELEASABLE, &cgrp->flags);
+}
+
+static struct cftype debug_files[] = {
+ {
+ .name = "cgroup_refcount",
+ .read_u64 = cgroup_refcount_read,
+ },
+ {
+ .name = "taskcount",
+ .read_u64 = debug_taskcount_read,
+ },
+
+ {
+ .name = "current_css_set",
+ .read_u64 = current_css_set_read,
+ },
+
+ {
+ .name = "current_css_set_refcount",
+ .read_u64 = current_css_set_refcount_read,
+ },
+
+ {
+ .name = "current_css_set_cg_links",
+ .read_seq_string = current_css_set_cg_links_read,
+ },
+
+ {
+ .name = "cgroup_css_links",
+ .read_seq_string = cgroup_css_links_read,
+ },
+
+ {
+ .name = "releasable",
+ .read_u64 = releasable_read,
+ },
+};
+
+static int debug_populate(struct cgroup_subsys *ss, struct cgroup *cont)
+{
+ return cgroup_add_files(cont, ss, debug_files,
+ ARRAY_SIZE(debug_files));
+}
+
+struct cgroup_subsys debug_subsys = {
+ .name = "debug",
+ .create = debug_create,
+ .destroy = debug_destroy,
+ .populate = debug_populate,
+ .subsys_id = debug_subsys_id,
+};
+#endif /* CONFIG_CGROUP_DEBUG */
+++ /dev/null
-/*
- * kernel/cgroup_debug.c - Example cgroup subsystem that
- * exposes debug info
- *
- * Copyright (C) Google Inc, 2007
- *
- * Developed by Paul Menage (menage@google.com)
- *
- */
-
-#include <linux/cgroup.h>
-#include <linux/fs.h>
-#include <linux/slab.h>
-#include <linux/rcupdate.h>
-
-#include <asm/atomic.h>
-
-static struct cgroup_subsys_state *debug_create(struct cgroup_subsys *ss,
- struct cgroup *cont)
-{
- struct cgroup_subsys_state *css = kzalloc(sizeof(*css), GFP_KERNEL);
-
- if (!css)
- return ERR_PTR(-ENOMEM);
-
- return css;
-}
-
-static void debug_destroy(struct cgroup_subsys *ss, struct cgroup *cont)
-{
- kfree(cont->subsys[debug_subsys_id]);
-}
-
-static u64 cgroup_refcount_read(struct cgroup *cont, struct cftype *cft)
-{
- return atomic_read(&cont->count);
-}
-
-static u64 taskcount_read(struct cgroup *cont, struct cftype *cft)
-{
- u64 count;
-
- count = cgroup_task_count(cont);
- return count;
-}
-
-static u64 current_css_set_read(struct cgroup *cont, struct cftype *cft)
-{
- return (u64)(long)current->cgroups;
-}
-
-static u64 current_css_set_refcount_read(struct cgroup *cont,
- struct cftype *cft)
-{
- u64 count;
-
- rcu_read_lock();
- count = atomic_read(¤t->cgroups->refcount);
- rcu_read_unlock();
- return count;
-}
-
-static u64 releasable_read(struct cgroup *cgrp, struct cftype *cft)
-{
- return test_bit(CGRP_RELEASABLE, &cgrp->flags);
-}
-
-static struct cftype files[] = {
- {
- .name = "cgroup_refcount",
- .read_u64 = cgroup_refcount_read,
- },
- {
- .name = "taskcount",
- .read_u64 = taskcount_read,
- },
-
- {
- .name = "current_css_set",
- .read_u64 = current_css_set_read,
- },
-
- {
- .name = "current_css_set_refcount",
- .read_u64 = current_css_set_refcount_read,
- },
-
- {
- .name = "releasable",
- .read_u64 = releasable_read,
- },
-};
-
-static int debug_populate(struct cgroup_subsys *ss, struct cgroup *cont)
-{
- return cgroup_add_files(cont, ss, files, ARRAY_SIZE(files));
-}
-
-struct cgroup_subsys debug_subsys = {
- .name = "debug",
- .create = debug_create,
- .destroy = debug_destroy,
- .populate = debug_populate,
- .subsys_id = debug_subsys_id,
-};
*/
static int freezer_can_attach(struct cgroup_subsys *ss,
struct cgroup *new_cgroup,
- struct task_struct *task)
+ struct task_struct *task, bool threadgroup)
{
struct freezer *freezer;
if (freezer->state == CGROUP_FROZEN)
return -EBUSY;
+ if (threadgroup) {
+ struct task_struct *c;
+
+ rcu_read_lock();
+ list_for_each_entry_rcu(c, &task->thread_group, thread_group) {
+ if (is_task_frozen_enough(c)) {
+ rcu_read_unlock();
+ return -EBUSY;
+ }
+ }
+ rcu_read_unlock();
+ }
+
return 0;
}
static cpumask_var_t cpus_attach;
/* Called by cgroups to determine if a cpuset is usable; cgroup_mutex held */
-static int cpuset_can_attach(struct cgroup_subsys *ss,
- struct cgroup *cont, struct task_struct *tsk)
+static int cpuset_can_attach(struct cgroup_subsys *ss, struct cgroup *cont,
+ struct task_struct *tsk, bool threadgroup)
{
+ int ret;
struct cpuset *cs = cgroup_cs(cont);
if (cpumask_empty(cs->cpus_allowed) || nodes_empty(cs->mems_allowed))
if (tsk->flags & PF_THREAD_BOUND)
return -EINVAL;
- return security_task_setscheduler(tsk, 0, NULL);
+ ret = security_task_setscheduler(tsk, 0, NULL);
+ if (ret)
+ return ret;
+ if (threadgroup) {
+ struct task_struct *c;
+
+ rcu_read_lock();
+ list_for_each_entry_rcu(c, &tsk->thread_group, thread_group) {
+ ret = security_task_setscheduler(c, 0, NULL);
+ if (ret) {
+ rcu_read_unlock();
+ return ret;
+ }
+ }
+ rcu_read_unlock();
+ }
+ return 0;
+}
+
+static void cpuset_attach_task(struct task_struct *tsk, nodemask_t *to,
+ struct cpuset *cs)
+{
+ int err;
+ /*
+ * can_attach beforehand should guarantee that this doesn't fail.
+ * TODO: have a better way to handle failure here
+ */
+ err = set_cpus_allowed_ptr(tsk, cpus_attach);
+ WARN_ON_ONCE(err);
+
+ task_lock(tsk);
+ cpuset_change_task_nodemask(tsk, to);
+ task_unlock(tsk);
+ cpuset_update_task_spread_flag(cs, tsk);
+
}
-static void cpuset_attach(struct cgroup_subsys *ss,
- struct cgroup *cont, struct cgroup *oldcont,
- struct task_struct *tsk)
+static void cpuset_attach(struct cgroup_subsys *ss, struct cgroup *cont,
+ struct cgroup *oldcont, struct task_struct *tsk,
+ bool threadgroup)
{
nodemask_t from, to;
struct mm_struct *mm;
struct cpuset *cs = cgroup_cs(cont);
struct cpuset *oldcs = cgroup_cs(oldcont);
- int err;
if (cs == &top_cpuset) {
cpumask_copy(cpus_attach, cpu_possible_mask);
guarantee_online_cpus(cs, cpus_attach);
guarantee_online_mems(cs, &to);
}
- err = set_cpus_allowed_ptr(tsk, cpus_attach);
- if (err)
- return;
- task_lock(tsk);
- cpuset_change_task_nodemask(tsk, &to);
- task_unlock(tsk);
- cpuset_update_task_spread_flag(cs, tsk);
+ /* do per-task migration stuff possibly for each in the threadgroup */
+ cpuset_attach_task(tsk, &to, cs);
+ if (threadgroup) {
+ struct task_struct *c;
+ rcu_read_lock();
+ list_for_each_entry_rcu(c, &tsk->thread_group, thread_group) {
+ cpuset_attach_task(c, &to, cs);
+ }
+ rcu_read_unlock();
+ }
+ /* change mm; only needs to be done once even if threadgroup */
from = oldcs->mems_allowed;
to = cs->mems_allowed;
mm = get_task_mm(tsk);
disassociate_ctty(1);
module_put(task_thread_info(tsk)->exec_domain->module);
- if (tsk->binfmt)
- module_put(tsk->binfmt->module);
proc_exit_connector(tsk);
int __user *wo_stat;
struct rusage __user *wo_rusage;
+ wait_queue_t child_wait;
int notask_error;
};
-static struct pid *task_pid_type(struct task_struct *task, enum pid_type type)
+static inline
+struct pid *task_pid_type(struct task_struct *task, enum pid_type type)
{
- struct pid *pid = NULL;
- if (type == PIDTYPE_PID)
- pid = task->pids[type].pid;
- else if (type < PIDTYPE_MAX)
- pid = task->group_leader->pids[type].pid;
- return pid;
+ if (type != PIDTYPE_PID)
+ task = task->group_leader;
+ return task->pids[type].pid;
}
-static int eligible_child(struct wait_opts *wo, struct task_struct *p)
+static int eligible_pid(struct wait_opts *wo, struct task_struct *p)
{
- int err;
-
- if (wo->wo_type < PIDTYPE_MAX) {
- if (task_pid_type(p, wo->wo_type) != wo->wo_pid)
- return 0;
- }
+ return wo->wo_type == PIDTYPE_MAX ||
+ task_pid_type(p, wo->wo_type) == wo->wo_pid;
+}
+static int eligible_child(struct wait_opts *wo, struct task_struct *p)
+{
+ if (!eligible_pid(wo, p))
+ return 0;
/* Wait for all children (clone and not) if __WALL is set;
* otherwise, wait for clone children *only* if __WCLONE is
* set; otherwise, wait for non-clone children *only*. (Note:
&& !(wo->wo_flags & __WALL))
return 0;
- err = security_task_wait(p);
- if (err)
- return err;
-
return 1;
}
put_task_struct(p);
infop = wo->wo_info;
- if (!retval)
- retval = put_user(SIGCHLD, &infop->si_signo);
- if (!retval)
- retval = put_user(0, &infop->si_errno);
- if (!retval)
- retval = put_user((short)why, &infop->si_code);
- if (!retval)
- retval = put_user(pid, &infop->si_pid);
- if (!retval)
- retval = put_user(uid, &infop->si_uid);
- if (!retval)
- retval = put_user(status, &infop->si_status);
+ if (infop) {
+ if (!retval)
+ retval = put_user(SIGCHLD, &infop->si_signo);
+ if (!retval)
+ retval = put_user(0, &infop->si_errno);
+ if (!retval)
+ retval = put_user((short)why, &infop->si_code);
+ if (!retval)
+ retval = put_user(pid, &infop->si_pid);
+ if (!retval)
+ retval = put_user(uid, &infop->si_uid);
+ if (!retval)
+ retval = put_user(status, &infop->si_status);
+ }
if (!retval)
retval = pid;
return retval;
* then ->notask_error is 0 if @p is an eligible child,
* or another error from security_task_wait(), or still -ECHILD.
*/
-static int wait_consider_task(struct wait_opts *wo, struct task_struct *parent,
- int ptrace, struct task_struct *p)
+static int wait_consider_task(struct wait_opts *wo, int ptrace,
+ struct task_struct *p)
{
int ret = eligible_child(wo, p);
if (!ret)
return ret;
+ ret = security_task_wait(p);
if (unlikely(ret < 0)) {
/*
* If we have not yet seen any eligible child,
* Do not consider detached threads.
*/
if (!task_detached(p)) {
- int ret = wait_consider_task(wo, tsk, 0, p);
+ int ret = wait_consider_task(wo, 0, p);
if (ret)
return ret;
}
struct task_struct *p;
list_for_each_entry(p, &tsk->ptraced, ptrace_entry) {
- int ret = wait_consider_task(wo, tsk, 1, p);
+ int ret = wait_consider_task(wo, 1, p);
if (ret)
return ret;
}
return 0;
}
+static int child_wait_callback(wait_queue_t *wait, unsigned mode,
+ int sync, void *key)
+{
+ struct wait_opts *wo = container_of(wait, struct wait_opts,
+ child_wait);
+ struct task_struct *p = key;
+
+ if (!eligible_pid(wo, p))
+ return 0;
+
+ if ((wo->wo_flags & __WNOTHREAD) && wait->private != p->parent)
+ return 0;
+
+ return default_wake_function(wait, mode, sync, key);
+}
+
+void __wake_up_parent(struct task_struct *p, struct task_struct *parent)
+{
+ __wake_up_sync_key(&parent->signal->wait_chldexit,
+ TASK_INTERRUPTIBLE, 1, p);
+}
+
static long do_wait(struct wait_opts *wo)
{
- DECLARE_WAITQUEUE(wait, current);
struct task_struct *tsk;
int retval;
trace_sched_process_wait(wo->wo_pid);
- add_wait_queue(¤t->signal->wait_chldexit,&wait);
+ init_waitqueue_func_entry(&wo->child_wait, child_wait_callback);
+ wo->child_wait.private = current;
+ add_wait_queue(¤t->signal->wait_chldexit, &wo->child_wait);
repeat:
/*
* If there is nothing that can match our critiera just get out.
}
end:
__set_current_state(TASK_RUNNING);
- remove_wait_queue(¤t->signal->wait_chldexit,&wait);
- if (wo->wo_info) {
- struct siginfo __user *infop = wo->wo_info;
-
- if (retval > 0)
- retval = 0;
- else {
- /*
- * For a WNOHANG return, clear out all the fields
- * we would set so the user can easily tell the
- * difference.
- */
- if (!retval)
- retval = put_user(0, &infop->si_signo);
- if (!retval)
- retval = put_user(0, &infop->si_errno);
- if (!retval)
- retval = put_user(0, &infop->si_code);
- if (!retval)
- retval = put_user(0, &infop->si_pid);
- if (!retval)
- retval = put_user(0, &infop->si_uid);
- if (!retval)
- retval = put_user(0, &infop->si_status);
- }
- }
+ remove_wait_queue(¤t->signal->wait_chldexit, &wo->child_wait);
return retval;
}
wo.wo_stat = NULL;
wo.wo_rusage = ru;
ret = do_wait(&wo);
+
+ if (ret > 0) {
+ ret = 0;
+ } else if (infop) {
+ /*
+ * For a WNOHANG return, clear out all the fields
+ * we would set so the user can easily tell the
+ * difference.
+ */
+ if (!ret)
+ ret = put_user(0, &infop->si_signo);
+ if (!ret)
+ ret = put_user(0, &infop->si_errno);
+ if (!ret)
+ ret = put_user(0, &infop->si_code);
+ if (!ret)
+ ret = put_user(0, &infop->si_pid);
+ if (!ret)
+ ret = put_user(0, &infop->si_uid);
+ if (!ret)
+ ret = put_user(0, &infop->si_status);
+ }
+
put_pid(pid);
/* avoid REGPARM breakage on x86: */
#include <linux/init_task.h>
+static void mm_init_aio(struct mm_struct *mm)
+{
+#ifdef CONFIG_AIO
+ spin_lock_init(&mm->ioctx_lock);
+ INIT_HLIST_HEAD(&mm->ioctx_list);
+#endif
+}
+
static struct mm_struct * mm_init(struct mm_struct * mm, struct task_struct *p)
{
atomic_set(&mm->mm_users, 1);
set_mm_counter(mm, file_rss, 0);
set_mm_counter(mm, anon_rss, 0);
spin_lock_init(&mm->page_table_lock);
- spin_lock_init(&mm->ioctx_lock);
- INIT_HLIST_HEAD(&mm->ioctx_list);
mm->free_area_cache = TASK_UNMAPPED_BASE;
mm->cached_hole_size = ~0UL;
+ mm_init_aio(mm);
mm_init_owner(mm, p);
if (likely(!mm_alloc_pgd(mm))) {
spin_unlock(&mmlist_lock);
}
put_swap_token(mm);
+ if (mm->binfmt)
+ module_put(mm->binfmt->module);
mmdrop(mm);
}
}
mm->hiwater_rss = get_mm_rss(mm);
mm->hiwater_vm = mm->total_vm;
+ if (mm->binfmt && !try_module_get(mm->binfmt->module))
+ goto free_pt;
+
return mm;
free_pt:
+ /* don't put binfmt in mmput, we haven't got module yet */
+ mm->binfmt = NULL;
mmput(mm);
fail_nomem:
if ((clone_flags & CLONE_SIGHAND) && !(clone_flags & CLONE_VM))
return ERR_PTR(-EINVAL);
+ /*
+ * Siblings of global init remain as zombies on exit since they are
+ * not reaped by their parent (swapper). To solve this and to avoid
+ * multi-rooted process trees, prevent global and container-inits
+ * from creating siblings.
+ */
+ if ((clone_flags & CLONE_PARENT) &&
+ current->signal->flags & SIGNAL_UNKILLABLE)
+ return ERR_PTR(-EINVAL);
+
retval = security_task_create(clone_flags);
if (retval)
goto fork_out;
if (!try_module_get(task_thread_info(p)->exec_domain->module))
goto bad_fork_cleanup_count;
- if (p->binfmt && !try_module_get(p->binfmt->module))
- goto bad_fork_cleanup_put_domain;
-
p->did_exec = 0;
delayacct_tsk_init(p); /* Must remain after dup_task_struct() */
copy_flags(clone_flags, p);
#endif
cgroup_exit(p, cgroup_callbacks_done);
delayacct_tsk_free(p);
- if (p->binfmt)
- module_put(p->binfmt->module);
-bad_fork_cleanup_put_domain:
module_put(task_thread_info(p)->exec_domain->module);
bad_fork_cleanup_count:
atomic_dec(&p->cred->user->processes);
union futex_key key;
};
-/*
- * We use this hashed waitqueue instead of a normal wait_queue_t, so
+/**
+ * struct futex_q - The hashed futex queue entry, one per waiting task
+ * @task: the task waiting on the futex
+ * @lock_ptr: the hash bucket lock
+ * @key: the key the futex is hashed on
+ * @pi_state: optional priority inheritance state
+ * @rt_waiter: rt_waiter storage for use with requeue_pi
+ * @requeue_pi_key: the requeue_pi target futex key
+ * @bitset: bitset for the optional bitmasked wakeup
+ *
+ * We use this hashed waitqueue, instead of a normal wait_queue_t, so
* we can wake only the relevant ones (hashed queues may be shared).
*
* A futex_q has a woken state, just like tasks have TASK_RUNNING.
* It is considered woken when plist_node_empty(&q->list) || q->lock_ptr == 0.
* The order of wakup is always to make the first condition true, then
- * wake up q->waiter, then make the second condition true.
+ * the second.
+ *
+ * PI futexes are typically woken before they are removed from the hash list via
+ * the rt_mutex code. See unqueue_me_pi().
*/
struct futex_q {
struct plist_node list;
- /* Waiter reference */
- struct task_struct *task;
- /* Which hash list lock to use: */
+ struct task_struct *task;
spinlock_t *lock_ptr;
-
- /* Key which the futex is hashed on: */
union futex_key key;
-
- /* Optional priority inheritance state: */
struct futex_pi_state *pi_state;
-
- /* rt_waiter storage for requeue_pi: */
struct rt_mutex_waiter *rt_waiter;
-
- /* The expected requeue pi target futex key: */
union futex_key *requeue_pi_key;
-
- /* Bitset for the optional bitmasked wakeup */
u32 bitset;
};
}
/**
- * get_futex_key - Get parameters which are the keys for a futex.
- * @uaddr: virtual address of the futex
- * @fshared: 0 for a PROCESS_PRIVATE futex, 1 for PROCESS_SHARED
- * @key: address where result is stored.
- * @rw: mapping needs to be read/write (values: VERIFY_READ, VERIFY_WRITE)
+ * get_futex_key() - Get parameters which are the keys for a futex
+ * @uaddr: virtual address of the futex
+ * @fshared: 0 for a PROCESS_PRIVATE futex, 1 for PROCESS_SHARED
+ * @key: address where result is stored.
+ * @rw: mapping needs to be read/write (values: VERIFY_READ,
+ * VERIFY_WRITE)
*
* Returns a negative error code or 0
* The key words are stored in *key on success.
drop_futex_key_refs(key);
}
-/*
- * fault_in_user_writeable - fault in user address and verify RW access
+/**
+ * fault_in_user_writeable() - Fault in user address and verify RW access
* @uaddr: pointer to faulting user space address
*
* Slow path to fixup the fault we just took in the atomic write
/**
* futex_top_waiter() - Return the highest priority waiter on a futex
- * @hb: the hash bucket the futex_q's reside in
- * @key: the futex key (to distinguish it from other futex futex_q's)
+ * @hb: the hash bucket the futex_q's reside in
+ * @key: the futex key (to distinguish it from other futex futex_q's)
*
* Must be called with the hb lock held.
*/
}
/**
- * futex_lock_pi_atomic() - atomic work required to acquire a pi aware futex
+ * futex_lock_pi_atomic() - Atomic work required to acquire a pi aware futex
* @uaddr: the pi futex user address
* @hb: the pi futex hash bucket
* @key: the futex key associated with uaddr and hb
/**
* requeue_pi_wake_futex() - Wake a task that acquired the lock during requeue
- * q: the futex_q
- * key: the key of the requeue target futex
- * hb: the hash_bucket of the requeue target futex
+ * @q: the futex_q
+ * @key: the key of the requeue target futex
+ * @hb: the hash_bucket of the requeue target futex
*
* During futex_requeue, with requeue_pi=1, it is possible to acquire the
* target futex if it is uncontended or via a lock steal. Set the futex_q key
return hb;
}
+static inline void
+queue_unlock(struct futex_q *q, struct futex_hash_bucket *hb)
+{
+ spin_unlock(&hb->lock);
+ drop_futex_key_refs(&q->key);
+}
+
+/**
+ * queue_me() - Enqueue the futex_q on the futex_hash_bucket
+ * @q: The futex_q to enqueue
+ * @hb: The destination hash bucket
+ *
+ * The hb->lock must be held by the caller, and is released here. A call to
+ * queue_me() is typically paired with exactly one call to unqueue_me(). The
+ * exceptions involve the PI related operations, which may use unqueue_me_pi()
+ * or nothing if the unqueue is done as part of the wake process and the unqueue
+ * state is implicit in the state of woken task (see futex_wait_requeue_pi() for
+ * an example).
+ */
static inline void queue_me(struct futex_q *q, struct futex_hash_bucket *hb)
{
int prio;
spin_unlock(&hb->lock);
}
-static inline void
-queue_unlock(struct futex_q *q, struct futex_hash_bucket *hb)
-{
- spin_unlock(&hb->lock);
- drop_futex_key_refs(&q->key);
-}
-
-/*
- * queue_me and unqueue_me must be called as a pair, each
- * exactly once. They are called with the hashed spinlock held.
+/**
+ * unqueue_me() - Remove the futex_q from its futex_hash_bucket
+ * @q: The futex_q to unqueue
+ *
+ * The q->lock_ptr must not be held by the caller. A call to unqueue_me() must
+ * be paired with exactly one earlier call to queue_me().
+ *
+ * Returns:
+ * 1 - if the futex_q was still queued (and we removed unqueued it)
+ * 0 - if the futex_q was already removed by the waking thread
*/
-
-/* Return 1 if we were still queued (ie. 0 means we were woken) */
static int unqueue_me(struct futex_q *q)
{
spinlock_t *lock_ptr;
static void futex_wait_queue_me(struct futex_hash_bucket *hb, struct futex_q *q,
struct hrtimer_sleeper *timeout)
{
- queue_me(q, hb);
-
/*
- * There might have been scheduling since the queue_me(), as we
- * cannot hold a spinlock across the get_user() in case it
- * faults, and we cannot just set TASK_INTERRUPTIBLE state when
- * queueing ourselves into the futex hash. This code thus has to
- * rely on the futex_wake() code removing us from hash when it
- * wakes us up.
+ * The task state is guaranteed to be set before another task can
+ * wake it. set_current_state() is implemented using set_mb() and
+ * queue_me() calls spin_unlock() upon completion, both serializing
+ * access to the hash list and forcing another memory barrier.
*/
set_current_state(TASK_INTERRUPTIBLE);
+ queue_me(q, hb);
/* Arm the timer */
if (timeout) {
}
/*
- * !plist_node_empty() is safe here without any lock.
- * q.lock_ptr != 0 is not safe, because of ordering against wakeup.
+ * If we have been removed from the hash list, then another task
+ * has tried to wake us, and we can skip the call to schedule().
*/
if (likely(!plist_node_empty(&q->list))) {
/*
/**
* futex_wait_requeue_pi() - Wait on uaddr and take uaddr2
- * @uaddr: the futex we initialyl wait on (non-pi)
+ * @uaddr: the futex we initially wait on (non-pi)
* @fshared: whether the futexes are shared (1) or not (0). They must be
* the same type, no requeueing from private to shared, etc.
* @val: the expected value of uaddr
* @abs_time: absolute timeout
- * @bitset: 32 bit wakeup bitset set by userspace, defaults to all.
+ * @bitset: 32 bit wakeup bitset set by userspace, defaults to all
* @clockrt: whether to use CLOCK_REALTIME (1) or CLOCK_MONOTONIC (0)
* @uaddr2: the pi futex we will take prior to returning to user-space
*
res = fixup_owner(uaddr2, fshared, &q, !ret);
/*
* If fixup_owner() returned an error, proprogate that. If it
- * acquired the lock, clear our -ETIMEDOUT or -EINTR.
+ * acquired the lock, clear -ETIMEDOUT or -EINTR.
*/
if (res)
ret = (res < 0) ? res : 0;
*/
/**
- * sys_set_robust_list - set the robust-futex list head of a task
- * @head: pointer to the list-head
- * @len: length of the list-head, as userspace expects
+ * sys_set_robust_list() - Set the robust-futex list head of a task
+ * @head: pointer to the list-head
+ * @len: length of the list-head, as userspace expects
*/
SYSCALL_DEFINE2(set_robust_list, struct robust_list_head __user *, head,
size_t, len)
}
/**
- * sys_get_robust_list - get the robust-futex list head of a task
- * @pid: pid of the process [zero for current task]
- * @head_ptr: pointer to a list-head pointer, the kernel fills it in
- * @len_ptr: pointer to a length field, the kernel fills in the header size
+ * sys_get_robust_list() - Get the robust-futex list head of a task
+ * @pid: pid of the process [zero for current task]
+ * @head_ptr: pointer to a list-head pointer, the kernel fills it in
+ * @len_ptr: pointer to a length field, the kernel fills in the header size
*/
SYSCALL_DEFINE3(get_robust_list, int, pid,
struct robust_list_head __user * __user *, head_ptr,
config GCOV_PROFILE_ALL
bool "Profile entire Kernel"
depends on GCOV_KERNEL
- depends on S390 || X86 || (PPC && EXPERIMENTAL)
+ depends on S390 || X86 || (PPC && EXPERIMENTAL) || MICROBLAZE
default n
---help---
This options activates profiling for the entire kernel.
* next event
* Called with interrupts disabled and base->lock held
*/
-static void hrtimer_force_reprogram(struct hrtimer_cpu_base *cpu_base)
+static void
+hrtimer_force_reprogram(struct hrtimer_cpu_base *cpu_base, int skip_equal)
{
int i;
struct hrtimer_clock_base *base = cpu_base->clock_base;
- ktime_t expires;
+ ktime_t expires, expires_next;
- cpu_base->expires_next.tv64 = KTIME_MAX;
+ expires_next.tv64 = KTIME_MAX;
for (i = 0; i < HRTIMER_MAX_CLOCK_BASES; i++, base++) {
struct hrtimer *timer;
*/
if (expires.tv64 < 0)
expires.tv64 = 0;
- if (expires.tv64 < cpu_base->expires_next.tv64)
- cpu_base->expires_next = expires;
+ if (expires.tv64 < expires_next.tv64)
+ expires_next = expires;
}
+ if (skip_equal && expires_next.tv64 == cpu_base->expires_next.tv64)
+ return;
+
+ cpu_base->expires_next.tv64 = expires_next.tv64;
+
if (cpu_base->expires_next.tv64 != KTIME_MAX)
tick_program_event(cpu_base->expires_next, 1);
}
base->clock_base[CLOCK_REALTIME].offset =
timespec_to_ktime(realtime_offset);
- hrtimer_force_reprogram(base);
+ hrtimer_force_reprogram(base, 0);
spin_unlock(&base->lock);
}
static inline int hrtimer_hres_active(void) { return 0; }
static inline int hrtimer_is_hres_enabled(void) { return 0; }
static inline int hrtimer_switch_to_hres(void) { return 0; }
-static inline void hrtimer_force_reprogram(struct hrtimer_cpu_base *base) { }
+static inline void
+hrtimer_force_reprogram(struct hrtimer_cpu_base *base, int skip_equal) { }
static inline int hrtimer_enqueue_reprogram(struct hrtimer *timer,
struct hrtimer_clock_base *base,
int wakeup)
struct hrtimer_clock_base *base,
unsigned long newstate, int reprogram)
{
- if (timer->state & HRTIMER_STATE_ENQUEUED) {
- /*
- * Remove the timer from the rbtree and replace the
- * first entry pointer if necessary.
- */
- if (base->first == &timer->node) {
- base->first = rb_next(&timer->node);
- /* Reprogram the clock event device. if enabled */
- if (reprogram && hrtimer_hres_active())
- hrtimer_force_reprogram(base->cpu_base);
+ if (!(timer->state & HRTIMER_STATE_ENQUEUED))
+ goto out;
+
+ /*
+ * Remove the timer from the rbtree and replace the first
+ * entry pointer if necessary.
+ */
+ if (base->first == &timer->node) {
+ base->first = rb_next(&timer->node);
+#ifdef CONFIG_HIGH_RES_TIMERS
+ /* Reprogram the clock event device. if enabled */
+ if (reprogram && hrtimer_hres_active()) {
+ ktime_t expires;
+
+ expires = ktime_sub(hrtimer_get_expires(timer),
+ base->offset);
+ if (base->cpu_base->expires_next.tv64 == expires.tv64)
+ hrtimer_force_reprogram(base->cpu_base, 1);
}
- rb_erase(&timer->node, &base->active);
+#endif
}
+ rb_erase(&timer->node, &base->active);
+out:
timer->state = newstate;
}
* Process updating of timeout sysctl
*/
int proc_dohung_task_timeout_secs(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
int ret;
- ret = proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos);
+ ret = proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
if (ret || !write)
goto out;
return seq_open(filp, &kprobes_seq_ops);
}
-static struct file_operations debugfs_kprobes_operations = {
+static const struct file_operations debugfs_kprobes_operations = {
.open = kprobes_open,
.read = seq_read,
.llseek = seq_lseek,
return count;
}
-static struct file_operations fops_kp = {
+static const struct file_operations fops_kp = {
.read = read_enabled_file_bool,
.write = write_enabled_file_bool,
};
}
}
+static void free_modinfo(struct module *mod)
+{
+ struct module_attribute *attr;
+ int i;
+
+ for (i = 0; (attr = modinfo_attrs[i]); i++) {
+ if (attr->free)
+ attr->free(mod);
+ }
+}
+
#ifdef CONFIG_KALLSYMS
/* lookup symbol in given range of kernel_symbols */
return '?';
}
+static bool is_core_symbol(const Elf_Sym *src, const Elf_Shdr *sechdrs,
+ unsigned int shnum)
+{
+ const Elf_Shdr *sec;
+
+ if (src->st_shndx == SHN_UNDEF
+ || src->st_shndx >= shnum
+ || !src->st_name)
+ return false;
+
+ sec = sechdrs + src->st_shndx;
+ if (!(sec->sh_flags & SHF_ALLOC)
+#ifndef CONFIG_KALLSYMS_ALL
+ || !(sec->sh_flags & SHF_EXECINSTR)
+#endif
+ || (sec->sh_entsize & INIT_OFFSET_MASK))
+ return false;
+
+ return true;
+}
+
+static unsigned long layout_symtab(struct module *mod,
+ Elf_Shdr *sechdrs,
+ unsigned int symindex,
+ unsigned int strindex,
+ const Elf_Ehdr *hdr,
+ const char *secstrings,
+ unsigned long *pstroffs,
+ unsigned long *strmap)
+{
+ unsigned long symoffs;
+ Elf_Shdr *symsect = sechdrs + symindex;
+ Elf_Shdr *strsect = sechdrs + strindex;
+ const Elf_Sym *src;
+ const char *strtab;
+ unsigned int i, nsrc, ndst;
+
+ /* Put symbol section at end of init part of module. */
+ symsect->sh_flags |= SHF_ALLOC;
+ symsect->sh_entsize = get_offset(mod, &mod->init_size, symsect,
+ symindex) | INIT_OFFSET_MASK;
+ DEBUGP("\t%s\n", secstrings + symsect->sh_name);
+
+ src = (void *)hdr + symsect->sh_offset;
+ nsrc = symsect->sh_size / sizeof(*src);
+ strtab = (void *)hdr + strsect->sh_offset;
+ for (ndst = i = 1; i < nsrc; ++i, ++src)
+ if (is_core_symbol(src, sechdrs, hdr->e_shnum)) {
+ unsigned int j = src->st_name;
+
+ while(!__test_and_set_bit(j, strmap) && strtab[j])
+ ++j;
+ ++ndst;
+ }
+
+ /* Append room for core symbols at end of core part. */
+ symoffs = ALIGN(mod->core_size, symsect->sh_addralign ?: 1);
+ mod->core_size = symoffs + ndst * sizeof(Elf_Sym);
+
+ /* Put string table section at end of init part of module. */
+ strsect->sh_flags |= SHF_ALLOC;
+ strsect->sh_entsize = get_offset(mod, &mod->init_size, strsect,
+ strindex) | INIT_OFFSET_MASK;
+ DEBUGP("\t%s\n", secstrings + strsect->sh_name);
+
+ /* Append room for core symbols' strings at end of core part. */
+ *pstroffs = mod->core_size;
+ __set_bit(0, strmap);
+ mod->core_size += bitmap_weight(strmap, strsect->sh_size);
+
+ return symoffs;
+}
+
static void add_kallsyms(struct module *mod,
Elf_Shdr *sechdrs,
+ unsigned int shnum,
unsigned int symindex,
unsigned int strindex,
- const char *secstrings)
+ unsigned long symoffs,
+ unsigned long stroffs,
+ const char *secstrings,
+ unsigned long *strmap)
{
- unsigned int i;
+ unsigned int i, ndst;
+ const Elf_Sym *src;
+ Elf_Sym *dst;
+ char *s;
mod->symtab = (void *)sechdrs[symindex].sh_addr;
mod->num_symtab = sechdrs[symindex].sh_size / sizeof(Elf_Sym);
for (i = 0; i < mod->num_symtab; i++)
mod->symtab[i].st_info
= elf_type(&mod->symtab[i], sechdrs, secstrings, mod);
+
+ mod->core_symtab = dst = mod->module_core + symoffs;
+ src = mod->symtab;
+ *dst = *src;
+ for (ndst = i = 1; i < mod->num_symtab; ++i, ++src) {
+ if (!is_core_symbol(src, sechdrs, shnum))
+ continue;
+ dst[ndst] = *src;
+ dst[ndst].st_name = bitmap_weight(strmap, dst[ndst].st_name);
+ ++ndst;
+ }
+ mod->core_num_syms = ndst;
+
+ mod->core_strtab = s = mod->module_core + stroffs;
+ for (*s = 0, i = 1; i < sechdrs[strindex].sh_size; ++i)
+ if (test_bit(i, strmap))
+ *++s = mod->strtab[i];
}
#else
+static inline unsigned long layout_symtab(struct module *mod,
+ Elf_Shdr *sechdrs,
+ unsigned int symindex,
+ unsigned int strindex,
+ const Elf_Ehdr *hdr,
+ const char *secstrings,
+ unsigned long *pstroffs,
+ unsigned long *strmap)
+{
+ return 0;
+}
+
static inline void add_kallsyms(struct module *mod,
Elf_Shdr *sechdrs,
+ unsigned int shnum,
unsigned int symindex,
unsigned int strindex,
- const char *secstrings)
+ unsigned long symoffs,
+ unsigned long stroffs,
+ const char *secstrings,
+ const unsigned long *strmap)
{
}
#endif /* CONFIG_KALLSYMS */
struct module *mod;
long err = 0;
void *percpu = NULL, *ptr = NULL; /* Stops spurious gcc warning */
+ unsigned long symoffs, stroffs, *strmap;
+
mm_segment_t old_fs;
DEBUGP("load_module: umod=%p, len=%lu, uargs=%p\n",
/* Don't keep modinfo and version sections. */
sechdrs[infoindex].sh_flags &= ~(unsigned long)SHF_ALLOC;
sechdrs[versindex].sh_flags &= ~(unsigned long)SHF_ALLOC;
-#ifdef CONFIG_KALLSYMS
- /* Keep symbol and string tables for decoding later. */
- sechdrs[symindex].sh_flags |= SHF_ALLOC;
- sechdrs[strindex].sh_flags |= SHF_ALLOC;
-#endif
/* Check module struct version now, before we try to use module. */
if (!check_modstruct_version(sechdrs, versindex, mod)) {
goto free_hdr;
}
+ strmap = kzalloc(BITS_TO_LONGS(sechdrs[strindex].sh_size)
+ * sizeof(long), GFP_KERNEL);
+ if (!strmap) {
+ err = -ENOMEM;
+ goto free_mod;
+ }
+
if (find_module(mod->name)) {
err = -EEXIST;
goto free_mod;
this is done generically; there doesn't appear to be any
special cases for the architectures. */
layout_sections(mod, hdr, sechdrs, secstrings);
+ symoffs = layout_symtab(mod, sechdrs, symindex, strindex, hdr,
+ secstrings, &stroffs, strmap);
/* Do the allocs. */
ptr = module_alloc_update_bounds(mod->core_size);
percpu_modcopy(mod->percpu, (void *)sechdrs[pcpuindex].sh_addr,
sechdrs[pcpuindex].sh_size);
- add_kallsyms(mod, sechdrs, symindex, strindex, secstrings);
+ add_kallsyms(mod, sechdrs, hdr->e_shnum, symindex, strindex,
+ symoffs, stroffs, secstrings, strmap);
+ kfree(strmap);
+ strmap = NULL;
if (!mod->taints) {
struct _ddebug *debug;
synchronize_sched();
module_arch_cleanup(mod);
cleanup:
+ free_modinfo(mod);
kobject_del(&mod->mkobj.kobj);
kobject_put(&mod->mkobj.kobj);
free_unload:
module_unload_free(mod);
#if defined(CONFIG_MODULE_UNLOAD) && defined(CONFIG_SMP)
- free_init:
percpu_modfree(mod->refptr);
+ free_init:
#endif
module_free(mod, mod->module_init);
free_core:
percpu_modfree(percpu);
free_mod:
kfree(args);
+ kfree(strmap);
free_hdr:
vfree(hdr);
return ERR_PTR(err);
/* Drop initial reference. */
module_put(mod);
trim_init_extable(mod);
+#ifdef CONFIG_KALLSYMS
+ mod->num_symtab = mod->core_num_syms;
+ mod->symtab = mod->core_symtab;
+ mod->strtab = mod->core_strtab;
+#endif
module_free(mod, mod->module_init);
mod->module_init = NULL;
mod->init_size = 0;
struct modversion_info *ver,
struct kernel_param *kp,
struct kernel_symbol *ks,
- struct marker *marker,
struct tracepoint *tp)
{
}
* (hence either you are in the same cgroup as task, or in an
* ancestor cgroup thereof)
*/
-static int ns_can_attach(struct cgroup_subsys *ss,
- struct cgroup *new_cgroup, struct task_struct *task)
+static int ns_can_attach(struct cgroup_subsys *ss, struct cgroup *new_cgroup,
+ struct task_struct *task, bool threadgroup)
{
if (current != task) {
if (!capable(CAP_SYS_ADMIN))
if (!cgroup_is_descendant(new_cgroup, task))
return -EPERM;
+ if (threadgroup) {
+ struct task_struct *c;
+ rcu_read_lock();
+ list_for_each_entry_rcu(c, &task->thread_group, thread_group) {
+ if (!cgroup_is_descendant(new_cgroup, c)) {
+ rcu_read_unlock();
+ return -EPERM;
+ }
+ }
+ rcu_read_unlock();
+ }
+
return 0;
}
#include <linux/device.h>
#include <linux/err.h>
#include <linux/slab.h>
+#include <linux/ctype.h>
#if 0
#define DEBUGP printk
}
for (i = 0; args[i]; i++) {
- if (args[i] == ' ' && !in_quote)
+ if (isspace(args[i]) && !in_quote)
break;
if (equals == 0) {
if (args[i] == '=')
next = args + i;
/* Chew up trailing spaces. */
- while (*next == ' ')
+ while (isspace(*next))
next++;
return next;
}
DEBUGP("Parsing ARGS: %s\n", args);
/* Chew leading spaces */
- while (*args == ' ')
+ while (isspace(*args))
args++;
while (*args) {
}
}
-static struct vm_operations_struct perf_mmap_vmops = {
+static const struct vm_operations_struct perf_mmap_vmops = {
.open = perf_mmap_open,
.close = perf_mmap_close,
.fault = perf_mmap_fault,
{
if (!(flags & CLONE_NEWPID))
return get_pid_ns(old_ns);
- if (flags & CLONE_THREAD)
+ if (flags & (CLONE_THREAD|CLONE_PARENT))
return ERR_PTR(-EINVAL);
return create_pid_namespace(old_ns);
}
* or self-reaping. Do notification now if it would have happened earlier.
* If it should reap itself, return true.
*
- * If it's our own child, there is no notification to do.
- * But if our normal children self-reap, then this child
- * was prevented by ptrace and we must reap it now.
+ * If it's our own child, there is no notification to do. But if our normal
+ * children self-reap, then this child was prevented by ptrace and we must
+ * reap it now, in that case we must also wake up sub-threads sleeping in
+ * do_wait().
*/
static bool __ptrace_detach(struct task_struct *tracer, struct task_struct *p)
{
if (!task_detached(p) && thread_group_empty(p)) {
if (!same_thread_group(p->real_parent, tracer))
do_notify_parent(p, p->exit_signal);
- else if (ignoring_children(tracer->sighand))
+ else if (ignoring_children(tracer->sighand)) {
+ __wake_up_parent(p, tracer);
p->exit_signal = -1;
+ }
}
if (task_detached(p)) {
/* Mark it as in the process of being reaped. */
return single_open(file, show_rcudata, NULL);
}
-static struct file_operations rcudata_fops = {
+static const struct file_operations rcudata_fops = {
.owner = THIS_MODULE,
.open = rcudata_open,
.read = seq_read,
return single_open(file, show_rcudata_csv, NULL);
}
-static struct file_operations rcudata_csv_fops = {
+static const struct file_operations rcudata_csv_fops = {
.owner = THIS_MODULE,
.open = rcudata_csv_open,
.read = seq_read,
return single_open(file, show_rcuhier, NULL);
}
-static struct file_operations rcuhier_fops = {
+static const struct file_operations rcuhier_fops = {
.owner = THIS_MODULE,
.open = rcuhier_open,
.read = seq_read,
return single_open(file, show_rcugp, NULL);
}
-static struct file_operations rcugp_fops = {
+static const struct file_operations rcugp_fops = {
.owner = THIS_MODULE,
.open = rcugp_open,
.read = seq_read,
return single_open(file, show_rcu_pending, NULL);
}
-static struct file_operations rcu_pending_fops = {
+static const struct file_operations rcu_pending_fops = {
.owner = THIS_MODULE,
.open = rcu_pending_open,
.read = seq_read,
/*
* vm_ops for relay file mappings.
*/
-static struct vm_operations_struct relay_file_mmap_ops = {
+static const struct vm_operations_struct relay_file_mmap_ops = {
.fault = relay_buf_fault,
.close = relay_file_mmap_close,
};
{
spin_lock_init(&counter->lock);
counter->limit = RESOURCE_MAX;
+ counter->soft_limit = RESOURCE_MAX;
counter->parent = parent;
}
return &counter->limit;
case RES_FAILCNT:
return &counter->failcnt;
+ case RES_SOFT_LIMIT:
+ return &counter->soft_limit;
};
BUG();
return single_open(filp, sched_feat_show, NULL);
}
-static struct file_operations sched_feat_fops = {
+static const struct file_operations sched_feat_fops = {
.open = sched_feat_open,
.write = sched_feat_write,
.read = seq_read,
#endif /* CONFIG_RT_GROUP_SCHED */
int sched_rt_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int ret;
old_period = sysctl_sched_rt_period;
old_runtime = sysctl_sched_rt_runtime;
- ret = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
if (!ret && write) {
ret = sched_rt_global_constraints();
}
static int
-cpu_cgroup_can_attach(struct cgroup_subsys *ss, struct cgroup *cgrp,
- struct task_struct *tsk)
+cpu_cgroup_can_attach_task(struct cgroup *cgrp, struct task_struct *tsk)
{
#ifdef CONFIG_RT_GROUP_SCHED
if (!sched_rt_can_attach(cgroup_tg(cgrp), tsk))
if (tsk->sched_class != &fair_sched_class)
return -EINVAL;
#endif
+ return 0;
+}
+static int
+cpu_cgroup_can_attach(struct cgroup_subsys *ss, struct cgroup *cgrp,
+ struct task_struct *tsk, bool threadgroup)
+{
+ int retval = cpu_cgroup_can_attach_task(cgrp, tsk);
+ if (retval)
+ return retval;
+ if (threadgroup) {
+ struct task_struct *c;
+ rcu_read_lock();
+ list_for_each_entry_rcu(c, &tsk->thread_group, thread_group) {
+ retval = cpu_cgroup_can_attach_task(cgrp, c);
+ if (retval) {
+ rcu_read_unlock();
+ return retval;
+ }
+ }
+ rcu_read_unlock();
+ }
return 0;
}
static void
cpu_cgroup_attach(struct cgroup_subsys *ss, struct cgroup *cgrp,
- struct cgroup *old_cont, struct task_struct *tsk)
+ struct cgroup *old_cont, struct task_struct *tsk,
+ bool threadgroup)
{
sched_move_task(tsk);
+ if (threadgroup) {
+ struct task_struct *c;
+ rcu_read_lock();
+ list_for_each_entry_rcu(c, &tsk->thread_group, thread_group) {
+ sched_move_task(c);
+ }
+ rcu_read_unlock();
+ }
}
#ifdef CONFIG_FAIR_GROUP_SCHED
clock = wrap_max(clock, min_clock);
clock = wrap_min(clock, max_clock);
- if (cmpxchg(&scd->clock, old_clock, clock) != old_clock)
+ if (cmpxchg64(&scd->clock, old_clock, clock) != old_clock)
goto again;
return clock;
val = remote_clock;
}
- if (cmpxchg(ptr, old_val, val) != old_val)
+ if (cmpxchg64(ptr, old_val, val) != old_val)
goto again;
return val;
#ifdef CONFIG_SCHED_DEBUG
int sched_nr_latency_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
- int ret = proc_dointvec_minmax(table, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
if (ret || !write)
return ret;
if (why) {
/*
- * The first thread which returns from finish_stop()
+ * The first thread which returns from do_signal_stop()
* will take ->siglock, notice SIGNAL_CLD_MASK, and
* notify its parent. See get_signal_to_deliver().
*/
return send_signal(sig, info, t, 0);
}
+int do_send_sig_info(int sig, struct siginfo *info, struct task_struct *p,
+ bool group)
+{
+ unsigned long flags;
+ int ret = -ESRCH;
+
+ if (lock_task_sighand(p, &flags)) {
+ ret = send_signal(sig, info, p, group);
+ unlock_task_sighand(p, &flags);
+ }
+
+ return ret;
+}
+
/*
* Force a signal that the process can't ignore: if necessary
* we unblock the signal and change any SIG_IGN to SIG_DFL.
}
}
-int __fatal_signal_pending(struct task_struct *tsk)
-{
- return sigismember(&tsk->pending.signal, SIGKILL);
-}
-EXPORT_SYMBOL(__fatal_signal_pending);
-
struct sighand_struct *lock_task_sighand(struct task_struct *tsk, unsigned long *flags)
{
struct sighand_struct *sighand;
*/
int group_send_sig_info(int sig, struct siginfo *info, struct task_struct *p)
{
- unsigned long flags;
- int ret;
+ int ret = check_kill_permission(sig, info, p);
- ret = check_kill_permission(sig, info, p);
-
- if (!ret && sig) {
- ret = -ESRCH;
- if (lock_task_sighand(p, &flags)) {
- ret = __group_send_sig_info(sig, info, p);
- unlock_task_sighand(p, &flags);
- }
- }
+ if (!ret && sig)
+ ret = do_send_sig_info(sig, info, p, true);
return ret;
}
* These are for backward compatibility with the rest of the kernel source.
*/
-/*
- * The caller must ensure the task can't exit.
- */
int
send_sig_info(int sig, struct siginfo *info, struct task_struct *p)
{
- int ret;
- unsigned long flags;
-
/*
* Make sure legacy kernel users don't send in bad values
* (normal paths check this in check_kill_permission).
if (!valid_signal(sig))
return -EINVAL;
- spin_lock_irqsave(&p->sighand->siglock, flags);
- ret = specific_send_sig_info(sig, info, p);
- spin_unlock_irqrestore(&p->sighand->siglock, flags);
- return ret;
+ return do_send_sig_info(sig, info, p, false);
}
#define __si_special(priv) \
return ret;
}
-/*
- * Wake up any threads in the parent blocked in wait* syscalls.
- */
-static inline void __wake_up_parent(struct task_struct *p,
- struct task_struct *parent)
-{
- wake_up_interruptible_sync(&parent->signal->wait_chldexit);
-}
-
/*
* Let a parent know about the death of a child.
* For a stopped/continued status change, use do_notify_parent_cldstop instead.
spin_unlock_irq(¤t->sighand->siglock);
}
-static void
-finish_stop(int stop_count)
-{
- /*
- * If there are no other threads in the group, or if there is
- * a group stop in progress and we are the last to stop,
- * report to the parent. When ptraced, every thread reports itself.
- */
- if (tracehook_notify_jctl(stop_count == 0, CLD_STOPPED)) {
- read_lock(&tasklist_lock);
- do_notify_parent_cldstop(current, CLD_STOPPED);
- read_unlock(&tasklist_lock);
- }
-
- do {
- schedule();
- } while (try_to_freeze());
- /*
- * Now we don't run again until continued.
- */
- current->exit_code = 0;
-}
-
/*
* This performs the stopping for SIGSTOP and other stop signals.
* We have to stop all threads in the thread group.
static int do_signal_stop(int signr)
{
struct signal_struct *sig = current->signal;
- int stop_count;
+ int notify;
- if (sig->group_stop_count > 0) {
- /*
- * There is a group stop in progress. We don't need to
- * start another one.
- */
- stop_count = --sig->group_stop_count;
- } else {
+ if (!sig->group_stop_count) {
struct task_struct *t;
if (!likely(sig->flags & SIGNAL_STOP_DEQUEUED) ||
*/
sig->group_exit_code = signr;
- stop_count = 0;
+ sig->group_stop_count = 1;
for (t = next_thread(current); t != current; t = next_thread(t))
/*
* Setting state to TASK_STOPPED for a group
*/
if (!(t->flags & PF_EXITING) &&
!task_is_stopped_or_traced(t)) {
- stop_count++;
+ sig->group_stop_count++;
signal_wake_up(t, 0);
}
- sig->group_stop_count = stop_count;
}
+ /*
+ * If there are no other threads in the group, or if there is
+ * a group stop in progress and we are the last to stop, report
+ * to the parent. When ptraced, every thread reports itself.
+ */
+ notify = sig->group_stop_count == 1 ? CLD_STOPPED : 0;
+ notify = tracehook_notify_jctl(notify, CLD_STOPPED);
+ /*
+ * tracehook_notify_jctl() can drop and reacquire siglock, so
+ * we keep ->group_stop_count != 0 before the call. If SIGCONT
+ * or SIGKILL comes in between ->group_stop_count == 0.
+ */
+ if (sig->group_stop_count) {
+ if (!--sig->group_stop_count)
+ sig->flags = SIGNAL_STOP_STOPPED;
+ current->exit_code = sig->group_exit_code;
+ __set_current_state(TASK_STOPPED);
+ }
+ spin_unlock_irq(¤t->sighand->siglock);
- if (stop_count == 0)
- sig->flags = SIGNAL_STOP_STOPPED;
- current->exit_code = sig->group_exit_code;
- __set_current_state(TASK_STOPPED);
+ if (notify) {
+ read_lock(&tasklist_lock);
+ do_notify_parent_cldstop(current, notify);
+ read_unlock(&tasklist_lock);
+ }
+
+ /* Now we don't run again until woken by SIGCONT or SIGKILL */
+ do {
+ schedule();
+ } while (try_to_freeze());
+
+ tracehook_finish_jctl();
+ current->exit_code = 0;
- spin_unlock_irq(¤t->sighand->siglock);
- finish_stop(stop_count);
return 1;
}
int why = (signal->flags & SIGNAL_STOP_CONTINUED)
? CLD_CONTINUED : CLD_STOPPED;
signal->flags &= ~SIGNAL_CLD_MASK;
- spin_unlock_irq(&sighand->siglock);
- if (unlikely(!tracehook_notify_jctl(1, why)))
- goto relock;
+ why = tracehook_notify_jctl(why, CLD_CONTINUED);
+ spin_unlock_irq(&sighand->siglock);
- read_lock(&tasklist_lock);
- do_notify_parent_cldstop(current->group_leader, why);
- read_unlock(&tasklist_lock);
+ if (why) {
+ read_lock(&tasklist_lock);
+ do_notify_parent_cldstop(current->group_leader, why);
+ read_unlock(&tasklist_lock);
+ }
goto relock;
}
if (unlikely(tsk->signal->group_stop_count) &&
!--tsk->signal->group_stop_count) {
tsk->signal->flags = SIGNAL_STOP_STOPPED;
- group_stop = 1;
+ group_stop = tracehook_notify_jctl(CLD_STOPPED, CLD_STOPPED);
}
out:
spin_unlock_irq(&tsk->sighand->siglock);
- if (unlikely(group_stop) && tracehook_notify_jctl(1, CLD_STOPPED)) {
+ if (unlikely(group_stop)) {
read_lock(&tasklist_lock);
- do_notify_parent_cldstop(tsk, CLD_STOPPED);
+ do_notify_parent_cldstop(tsk, group_stop);
read_unlock(&tasklist_lock);
}
}
do_send_specific(pid_t tgid, pid_t pid, int sig, struct siginfo *info)
{
struct task_struct *p;
- unsigned long flags;
int error = -ESRCH;
rcu_read_lock();
/*
* The null signal is a permissions and process existence
* probe. No signal is actually delivered.
- *
- * If lock_task_sighand() fails we pretend the task dies
- * after receiving the signal. The window is tiny, and the
- * signal is private anyway.
*/
- if (!error && sig && lock_task_sighand(p, &flags)) {
- error = specific_send_sig_info(sig, info, p);
- unlock_task_sighand(p, &flags);
+ if (!error && sig) {
+ error = do_send_sig_info(sig, info, p, false);
+ /*
+ * If lock_task_sighand() failed we pretend the task
+ * dies after receiving the signal. The window is tiny,
+ * and the signal is private anyway.
+ */
+ if (unlikely(error == -ESRCH))
+ error = 0;
}
}
rcu_read_unlock();
static void slow_work_oom_timeout(unsigned long);
#ifdef CONFIG_SYSCTL
-static int slow_work_min_threads_sysctl(struct ctl_table *, int, struct file *,
+static int slow_work_min_threads_sysctl(struct ctl_table *, int,
void __user *, size_t *, loff_t *);
-static int slow_work_max_threads_sysctl(struct ctl_table *, int , struct file *,
+static int slow_work_max_threads_sysctl(struct ctl_table *, int ,
void __user *, size_t *, loff_t *);
#endif
* Handle adjustment of the minimum number of threads
*/
static int slow_work_min_threads_sysctl(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
- int ret = proc_dointvec_minmax(table, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
int n;
if (ret == 0) {
* Handle adjustment of the maximum number of threads
*/
static int slow_work_max_threads_sysctl(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
- int ret = proc_dointvec_minmax(table, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
int n;
if (ret == 0) {
EXPORT_SYMBOL(touch_all_softlockup_watchdogs);
int proc_dosoftlockup_thresh(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
touch_all_softlockup_watchdogs();
- return proc_dointvec_minmax(table, write, filp, buffer, lenp, ppos);
+ return proc_dointvec_minmax(table, write, buffer, lenp, ppos);
}
/*
current->timer_slack_ns = arg2;
error = 0;
break;
+ case PR_MCE_KILL:
+ if (arg4 | arg5)
+ return -EINVAL;
+ switch (arg2) {
+ case 0:
+ if (arg3 != 0)
+ return -EINVAL;
+ current->flags &= ~PF_MCE_PROCESS;
+ break;
+ case 1:
+ current->flags |= PF_MCE_PROCESS;
+ if (arg3 != 0)
+ current->flags |= PF_MCE_EARLY;
+ else
+ current->flags &= ~PF_MCE_EARLY;
+ break;
+ default:
+ return -EINVAL;
+ }
+ error = 0;
+ break;
+
default:
error = -EINVAL;
break;
cond_syscall(compat_sys_sendmsg);
cond_syscall(sys_recvmsg);
cond_syscall(compat_sys_recvmsg);
+cond_syscall(compat_sys_recvfrom);
cond_syscall(sys_socketcall);
cond_syscall(sys_futex);
cond_syscall(compat_sys_futex);
extern int core_uses_pid;
extern int suid_dumpable;
extern char core_pattern[];
+extern unsigned int core_pipe_limit;
extern int pid_max;
extern int min_free_kbytes;
extern int pid_max_min, pid_max_max;
#endif
#ifdef CONFIG_PROC_SYSCTL
-static int proc_do_cad_pid(struct ctl_table *table, int write, struct file *filp,
+static int proc_do_cad_pid(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos);
-static int proc_taint(struct ctl_table *table, int write, struct file *filp,
+static int proc_taint(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos);
#endif
.proc_handler = &proc_dostring,
.strategy = &sysctl_string,
},
+ {
+ .ctl_name = CTL_UNNUMBERED,
+ .procname = "core_pipe_limit",
+ .data = &core_pipe_limit,
+ .maxlen = sizeof(unsigned int),
+ .mode = 0644,
+ .proc_handler = &proc_dointvec,
+ },
#ifdef CONFIG_PROC_SYSCTL
{
.procname = "tainted",
.mode = 0644,
.proc_handler = &scan_unevictable_handler,
},
+#ifdef CONFIG_MEMORY_FAILURE
+ {
+ .ctl_name = CTL_UNNUMBERED,
+ .procname = "memory_failure_early_kill",
+ .data = &sysctl_memory_failure_early_kill,
+ .maxlen = sizeof(sysctl_memory_failure_early_kill),
+ .mode = 0644,
+ .proc_handler = &proc_dointvec_minmax,
+ .strategy = &sysctl_intvec,
+ .extra1 = &zero,
+ .extra2 = &one,
+ },
+ {
+ .ctl_name = CTL_UNNUMBERED,
+ .procname = "memory_failure_recovery",
+ .data = &sysctl_memory_failure_recovery,
+ .maxlen = sizeof(sysctl_memory_failure_recovery),
+ .mode = 0644,
+ .proc_handler = &proc_dointvec_minmax,
+ .strategy = &sysctl_intvec,
+ .extra1 = &zero,
+ .extra2 = &one,
+ },
+#endif
+
/*
* NOTE: do not add new entries to this table unless you have read
* Documentation/sysctl/ctl_unnumbered.txt
#ifdef CONFIG_PROC_SYSCTL
static int _proc_do_string(void* data, int maxlen, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
size_t len;
* proc_dostring - read a string sysctl
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
*
* Returns 0 on success.
*/
-int proc_dostring(struct ctl_table *table, int write, struct file *filp,
+int proc_dostring(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
- return _proc_do_string(table->data, table->maxlen, write, filp,
+ return _proc_do_string(table->data, table->maxlen, write,
buffer, lenp, ppos);
}
}
static int __do_proc_dointvec(void *tbl_data, struct ctl_table *table,
- int write, struct file *filp, void __user *buffer,
+ int write, void __user *buffer,
size_t *lenp, loff_t *ppos,
int (*conv)(int *negp, unsigned long *lvalp, int *valp,
int write, void *data),
#undef TMPBUFLEN
}
-static int do_proc_dointvec(struct ctl_table *table, int write, struct file *filp,
+static int do_proc_dointvec(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos,
int (*conv)(int *negp, unsigned long *lvalp, int *valp,
int write, void *data),
void *data)
{
- return __do_proc_dointvec(table->data, table, write, filp,
+ return __do_proc_dointvec(table->data, table, write,
buffer, lenp, ppos, conv, data);
}
* proc_dointvec - read a vector of integers
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
*
* Returns 0 on success.
*/
-int proc_dointvec(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
- return do_proc_dointvec(table,write,filp,buffer,lenp,ppos,
+ return do_proc_dointvec(table,write,buffer,lenp,ppos,
NULL,NULL);
}
* Taint values can only be increased
* This means we can safely use a temporary.
*/
-static int proc_taint(struct ctl_table *table, int write, struct file *filp,
+static int proc_taint(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table t;
t = *table;
t.data = &tmptaint;
- err = proc_doulongvec_minmax(&t, write, filp, buffer, lenp, ppos);
+ err = proc_doulongvec_minmax(&t, write, buffer, lenp, ppos);
if (err < 0)
return err;
* proc_dointvec_minmax - read a vector of integers with min/max values
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
*
* Returns 0 on success.
*/
-int proc_dointvec_minmax(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_minmax(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct do_proc_dointvec_minmax_conv_param param = {
.min = (int *) table->extra1,
.max = (int *) table->extra2,
};
- return do_proc_dointvec(table, write, filp, buffer, lenp, ppos,
+ return do_proc_dointvec(table, write, buffer, lenp, ppos,
do_proc_dointvec_minmax_conv, ¶m);
}
static int __do_proc_doulongvec_minmax(void *data, struct ctl_table *table, int write,
- struct file *filp,
void __user *buffer,
size_t *lenp, loff_t *ppos,
unsigned long convmul,
}
static int do_proc_doulongvec_minmax(struct ctl_table *table, int write,
- struct file *filp,
void __user *buffer,
size_t *lenp, loff_t *ppos,
unsigned long convmul,
unsigned long convdiv)
{
return __do_proc_doulongvec_minmax(table->data, table, write,
- filp, buffer, lenp, ppos, convmul, convdiv);
+ buffer, lenp, ppos, convmul, convdiv);
}
/**
* proc_doulongvec_minmax - read a vector of long integers with min/max values
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
*
* Returns 0 on success.
*/
-int proc_doulongvec_minmax(struct ctl_table *table, int write, struct file *filp,
+int proc_doulongvec_minmax(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
- return do_proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos, 1l, 1l);
+ return do_proc_doulongvec_minmax(table, write, buffer, lenp, ppos, 1l, 1l);
}
/**
* proc_doulongvec_ms_jiffies_minmax - read a vector of millisecond values with min/max values
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
* Returns 0 on success.
*/
int proc_doulongvec_ms_jiffies_minmax(struct ctl_table *table, int write,
- struct file *filp,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
- return do_proc_doulongvec_minmax(table, write, filp, buffer,
+ return do_proc_doulongvec_minmax(table, write, buffer,
lenp, ppos, HZ, 1000l);
}
* proc_dointvec_jiffies - read a vector of integers as seconds
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
*
* Returns 0 on success.
*/
-int proc_dointvec_jiffies(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_jiffies(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
- return do_proc_dointvec(table,write,filp,buffer,lenp,ppos,
+ return do_proc_dointvec(table,write,buffer,lenp,ppos,
do_proc_dointvec_jiffies_conv,NULL);
}
* proc_dointvec_userhz_jiffies - read a vector of integers as 1/USER_HZ seconds
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: pointer to the file position
*
* Returns 0 on success.
*/
-int proc_dointvec_userhz_jiffies(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_userhz_jiffies(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
- return do_proc_dointvec(table,write,filp,buffer,lenp,ppos,
+ return do_proc_dointvec(table,write,buffer,lenp,ppos,
do_proc_dointvec_userhz_jiffies_conv,NULL);
}
* proc_dointvec_ms_jiffies - read a vector of integers as 1 milliseconds
* @table: the sysctl table
* @write: %TRUE if this is a write to the sysctl file
- * @filp: the file structure
* @buffer: the user buffer
* @lenp: the size of the user buffer
* @ppos: file position
*
* Returns 0 on success.
*/
-int proc_dointvec_ms_jiffies(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_ms_jiffies(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
- return do_proc_dointvec(table, write, filp, buffer, lenp, ppos,
+ return do_proc_dointvec(table, write, buffer, lenp, ppos,
do_proc_dointvec_ms_jiffies_conv, NULL);
}
-static int proc_do_cad_pid(struct ctl_table *table, int write, struct file *filp,
+static int proc_do_cad_pid(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct pid *new_pid;
tmp = pid_vnr(cad_pid);
- r = __do_proc_dointvec(&tmp, table, write, filp, buffer,
+ r = __do_proc_dointvec(&tmp, table, write, buffer,
lenp, ppos, NULL, NULL);
if (r || !write)
return r;
#else /* CONFIG_PROC_FS */
-int proc_dostring(struct ctl_table *table, int write, struct file *filp,
+int proc_dostring(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
-int proc_dointvec(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
-int proc_dointvec_minmax(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_minmax(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
-int proc_dointvec_jiffies(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_jiffies(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
-int proc_dointvec_userhz_jiffies(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_userhz_jiffies(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
-int proc_dointvec_ms_jiffies(struct ctl_table *table, int write, struct file *filp,
+int proc_dointvec_ms_jiffies(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
-int proc_doulongvec_minmax(struct ctl_table *table, int write, struct file *filp,
+int proc_doulongvec_minmax(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
return -ENOSYS;
}
int proc_doulongvec_ms_jiffies_minmax(struct ctl_table *table, int write,
- struct file *filp,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
-obj-y += timekeeping.o ntp.o clocksource.o jiffies.o timer_list.o timecompare.o
+obj-y += timekeeping.o ntp.o clocksource.o jiffies.o timer_list.o timecompare.o timeconv.o
obj-$(CONFIG_GENERIC_CLOCKEVENTS_BUILD) += clockevents.o
obj-$(CONFIG_GENERIC_CLOCKEVENTS) += tick-common.o
--- /dev/null
+/*
+ * Copyright (C) 1993, 1994, 1995, 1996, 1997 Free Software Foundation, Inc.
+ * This file is part of the GNU C Library.
+ * Contributed by Paul Eggert (eggert@twinsun.com).
+ *
+ * The GNU C Library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Library General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * The GNU C Library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * Library General Public License for more details.
+ *
+ * You should have received a copy of the GNU Library General Public
+ * License along with the GNU C Library; see the file COPYING.LIB. If not,
+ * write to the Free Software Foundation, Inc., 59 Temple Place - Suite 330,
+ * Boston, MA 02111-1307, USA.
+ */
+
+/*
+ * Converts the calendar time to broken-down time representation
+ * Based on code from glibc-2.6
+ *
+ * 2009-7-14:
+ * Moved from glibc-2.6 to kernel by Zhaolei<zhaolei@cn.fujitsu.com>
+ */
+
+#include <linux/time.h>
+#include <linux/module.h>
+
+/*
+ * Nonzero if YEAR is a leap year (every 4 years,
+ * except every 100th isn't, and every 400th is).
+ */
+static int __isleap(long year)
+{
+ return (year) % 4 == 0 && ((year) % 100 != 0 || (year) % 400 == 0);
+}
+
+/* do a mathdiv for long type */
+static long math_div(long a, long b)
+{
+ return a / b - (a % b < 0);
+}
+
+/* How many leap years between y1 and y2, y1 must less or equal to y2 */
+static long leaps_between(long y1, long y2)
+{
+ long leaps1 = math_div(y1 - 1, 4) - math_div(y1 - 1, 100)
+ + math_div(y1 - 1, 400);
+ long leaps2 = math_div(y2 - 1, 4) - math_div(y2 - 1, 100)
+ + math_div(y2 - 1, 400);
+ return leaps2 - leaps1;
+}
+
+/* How many days come before each month (0-12). */
+static const unsigned short __mon_yday[2][13] = {
+ /* Normal years. */
+ {0, 31, 59, 90, 120, 151, 181, 212, 243, 273, 304, 334, 365},
+ /* Leap years. */
+ {0, 31, 60, 91, 121, 152, 182, 213, 244, 274, 305, 335, 366}
+};
+
+#define SECS_PER_HOUR (60 * 60)
+#define SECS_PER_DAY (SECS_PER_HOUR * 24)
+
+/**
+ * time_to_tm - converts the calendar time to local broken-down time
+ *
+ * @totalsecs the number of seconds elapsed since 00:00:00 on January 1, 1970,
+ * Coordinated Universal Time (UTC).
+ * @offset offset seconds adding to totalsecs.
+ * @result pointer to struct tm variable to receive broken-down time
+ */
+void time_to_tm(time_t totalsecs, int offset, struct tm *result)
+{
+ long days, rem, y;
+ const unsigned short *ip;
+
+ days = totalsecs / SECS_PER_DAY;
+ rem = totalsecs % SECS_PER_DAY;
+ rem += offset;
+ while (rem < 0) {
+ rem += SECS_PER_DAY;
+ --days;
+ }
+ while (rem >= SECS_PER_DAY) {
+ rem -= SECS_PER_DAY;
+ ++days;
+ }
+
+ result->tm_hour = rem / SECS_PER_HOUR;
+ rem %= SECS_PER_HOUR;
+ result->tm_min = rem / 60;
+ result->tm_sec = rem % 60;
+
+ /* January 1, 1970 was a Thursday. */
+ result->tm_wday = (4 + days) % 7;
+ if (result->tm_wday < 0)
+ result->tm_wday += 7;
+
+ y = 1970;
+
+ while (days < 0 || days >= (__isleap(y) ? 366 : 365)) {
+ /* Guess a corrected year, assuming 365 days per year. */
+ long yg = y + math_div(days, 365);
+
+ /* Adjust DAYS and Y to match the guessed year. */
+ days -= (yg - y) * 365 + leaps_between(y, yg);
+ y = yg;
+ }
+
+ result->tm_year = y - 1900;
+
+ result->tm_yday = days;
+
+ ip = __mon_yday[__isleap(y)];
+ for (y = 11; days < ip[y]; y--)
+ continue;
+ days -= ip[y];
+
+ result->tm_mon = y;
+ result->tm_mday = days + 1;
+}
+EXPORT_SYMBOL(time_to_tm);
return single_open(filp, timer_list_show, NULL);
}
-static struct file_operations timer_list_fops = {
+static const struct file_operations timer_list_fops = {
.open = timer_list_open,
.read = seq_read,
.llseek = seq_lseek,
return single_open(filp, tstats_show, NULL);
}
-static struct file_operations tstats_fops = {
+static const struct file_operations tstats_fops = {
.open = tstats_open,
.read = seq_read,
.write = tstats_write,
sizeof(r), &r);
}
+/**
+ * blk_add_trace_rq_remap - Add a trace for a request-remap operation
+ * @q: queue the io is for
+ * @rq: the source request
+ * @dev: target device
+ * @from: source sector
+ *
+ * Description:
+ * Device mapper remaps request to other devices.
+ * Add a trace for that action.
+ *
+ **/
+static void blk_add_trace_rq_remap(struct request_queue *q,
+ struct request *rq, dev_t dev,
+ sector_t from)
+{
+ struct blk_trace *bt = q->blk_trace;
+ struct blk_io_trace_remap r;
+
+ if (likely(!bt))
+ return;
+
+ r.device_from = cpu_to_be32(dev);
+ r.device_to = cpu_to_be32(disk_devt(rq->rq_disk));
+ r.sector_from = cpu_to_be64(from);
+
+ __blk_add_trace(bt, blk_rq_pos(rq), blk_rq_bytes(rq),
+ rq_data_dir(rq), BLK_TA_REMAP, !!rq->errors,
+ sizeof(r), &r);
+}
+
/**
* blk_add_driver_data - Add binary message with driver-specific data
* @q: queue the io is for
WARN_ON(ret);
ret = register_trace_block_remap(blk_add_trace_remap);
WARN_ON(ret);
+ ret = register_trace_block_rq_remap(blk_add_trace_rq_remap);
+ WARN_ON(ret);
}
static void blk_unregister_tracepoints(void)
{
+ unregister_trace_block_rq_remap(blk_add_trace_rq_remap);
unregister_trace_block_remap(blk_add_trace_remap);
unregister_trace_block_split(blk_add_trace_split);
unregister_trace_block_unplug_io(blk_add_trace_unplug_io);
return sysfs_create_group(&dev->kobj, &blk_trace_attr_group);
}
+void blk_trace_remove_sysfs(struct device *dev)
+{
+ sysfs_remove_group(&dev->kobj, &blk_trace_attr_group);
+}
+
#endif /* CONFIG_BLK_DEV_IO_TRACE */
#ifdef CONFIG_EVENT_TRACING
if (ftrace_trace_function == ftrace_stub)
return;
+#ifdef CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST
func = ftrace_trace_function;
+#else
+ func = __ftrace_trace_function;
+#endif
if (ftrace_pid_trace) {
set_ftrace_pid_function(func);
if (!ret) {
struct seq_file *m = file->private_data;
m->private = iter;
- } else
+ } else {
+ trace_parser_put(&iter->parser);
kfree(iter);
+ }
} else
file->private_data = iter;
mutex_unlock(&ftrace_regex_lock);
struct trace_parser *parser;
ssize_t ret, read;
- if (!cnt || cnt < 0)
+ if (!cnt)
return 0;
mutex_lock(&ftrace_regex_lock);
parser = &iter->parser;
read = trace_get_user(parser, ubuf, cnt, ppos);
- if (trace_parser_loaded(parser) &&
+ if (read >= 0 && trace_parser_loaded(parser) &&
!trace_parser_cont(parser)) {
ret = ftrace_process_regex(parser->buffer,
parser->idx, enable);
size_t cnt, loff_t *ppos)
{
struct trace_parser parser;
- size_t read = 0;
- ssize_t ret;
+ ssize_t read, ret;
if (!cnt || cnt < 0)
return 0;
if (ftrace_graph_count >= FTRACE_GRAPH_MAX_FUNCS) {
ret = -EBUSY;
- goto out;
+ goto out_unlock;
}
if (trace_parser_get_init(&parser, FTRACE_BUFF_MAX)) {
ret = -ENOMEM;
- goto out;
+ goto out_unlock;
}
read = trace_get_user(&parser, ubuf, cnt, ppos);
- if (trace_parser_loaded((&parser))) {
+ if (read >= 0 && trace_parser_loaded((&parser))) {
parser.buffer[parser.idx] = 0;
/* we allow only one expression at a time */
ret = ftrace_set_func(ftrace_graph_funcs, &ftrace_graph_count,
parser.buffer);
if (ret)
- goto out;
+ goto out_free;
}
ret = read;
- out:
+
+out_free:
trace_parser_put(&parser);
+out_unlock:
mutex_unlock(&graph_lock);
return ret;
int
ftrace_enable_sysctl(struct ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int ret;
mutex_lock(&ftrace_lock);
- ret = proc_dointvec(table, write, file, buffer, lenp, ppos);
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
if (ret || !write || (last_ftrace_enabled == !!ftrace_enabled))
goto out;
return 1;
}
- if (!register_tracer(&kmem_tracer)) {
+ if (register_tracer(&kmem_tracer) != 0) {
pr_warning("Warning: could not register the kmem tracer\n");
return 1;
}
/* read the non-space input */
while (cnt && !isspace(ch)) {
- if (parser->idx < parser->size)
+ if (parser->idx < parser->size - 1)
parser->buffer[parser->idx++] = ch;
else {
ret = -EINVAL;
size_t cnt, loff_t *ppos)
{
struct trace_parser parser;
- size_t read = 0;
- ssize_t ret;
+ ssize_t read, ret;
- if (!cnt || cnt < 0)
+ if (!cnt)
return 0;
ret = tracing_update_buffers();
read = trace_get_user(&parser, ubuf, cnt, ppos);
- if (trace_parser_loaded((&parser))) {
+ if (read >= 0 && trace_parser_loaded((&parser))) {
int set = 1;
if (*parser.buffer == '!')
int
stack_trace_sysctl(struct ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int ret;
mutex_lock(&stack_sysctl_mutex);
- ret = proc_dointvec(table, write, file, buffer, lenp, ppos);
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
if (ret || !write ||
(last_stack_tracer_enabled == !!stack_tracer_enabled))
* Special case of dostring for the UTS structure. This has locks
* to observe. Should this be in kernel/sys.c ????
*/
-static int proc_do_uts_string(ctl_table *table, int write, struct file *filp,
+static int proc_do_uts_string(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct ctl_table uts_table;
int r;
memcpy(&uts_table, table, sizeof(uts_table));
uts_table.data = get_uts(table, write);
- r = proc_dostring(&uts_table,write,filp,buffer,lenp, ppos);
+ r = proc_dostring(&uts_table,write,buffer,lenp, ppos);
put_uts(table, write, uts_table.data);
return r;
}
#define GZIP_IOBUF_SIZE (16*1024)
+static int nofill(void *buffer, unsigned int len)
+{
+ return -1;
+}
+
/* Included from initramfs et al code */
STATIC int INIT gunzip(unsigned char *buf, int len,
int(*fill)(void*, unsigned int),
goto gunzip_nomem4;
}
+ if (!fill)
+ fill = nofill;
+
if (len == 0)
len = fill(zbuf, GZIP_IOBUF_SIZE);
#define RC_MODEL_TOTAL_BITS 11
+static int nofill(void *buffer, unsigned int len)
+{
+ return -1;
+}
+
/* Called twice: once at startup and once in rc_normalize() */
static void INIT rc_read(struct rc *rc)
{
int (*fill)(void*, unsigned int),
char *buffer, int buffer_size)
{
- rc->fill = fill;
+ if (fill)
+ rc->fill = fill;
+ else
+ rc->fill = nofill;
rc->buffer = (uint8_t *)buffer;
rc->buffer_size = buffer_size;
rc->buffer_end = rc->buffer + rc->buffer_size;
return p;
}
-static char *ip6_compressed_string(char *p, const struct in6_addr *addr)
+static char *ip6_compressed_string(char *p, const char *addr)
{
int i;
int j;
u8 hi;
u8 lo;
bool needcolon = false;
- bool useIPv4 = ipv6_addr_v4mapped(addr) || ipv6_addr_is_isatap(addr);
+ bool useIPv4;
+ struct in6_addr in6;
+
+ memcpy(&in6, addr, sizeof(struct in6_addr));
+
+ useIPv4 = ipv6_addr_v4mapped(&in6) || ipv6_addr_is_isatap(&in6);
memset(zerolength, 0, sizeof(zerolength));
/* find position of longest 0 run */
for (i = 0; i < range; i++) {
for (j = i; j < range; j++) {
- if (addr->s6_addr16[j] != 0)
+ if (in6.s6_addr16[j] != 0)
break;
zerolength[i]++;
}
needcolon = false;
}
/* hex u16 without leading 0s */
- word = ntohs(addr->s6_addr16[i]);
+ word = ntohs(in6.s6_addr16[i]);
hi = word >> 8;
lo = word & 0xff;
if (hi) {
if (useIPv4) {
if (needcolon)
*p++ = ':';
- p = ip4_string(p, &addr->s6_addr[12], false);
+ p = ip4_string(p, &in6.s6_addr[12], false);
}
*p = '\0';
return p;
}
-static char *ip6_string(char *p, const struct in6_addr *addr, const char *fmt)
+static char *ip6_string(char *p, const char *addr, const char *fmt)
{
int i;
for (i = 0; i < 8; i++) {
- p = pack_hex_byte(p, addr->s6_addr[2 * i]);
- p = pack_hex_byte(p, addr->s6_addr[2 * i + 1]);
+ p = pack_hex_byte(p, *addr++);
+ p = pack_hex_byte(p, *addr++);
if (fmt[0] == 'I' && i != 7)
*p++ = ':';
}
char ip6_addr[sizeof("xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:255.255.255.255")];
if (fmt[0] == 'I' && fmt[2] == 'c')
- ip6_compressed_string(ip6_addr, (const struct in6_addr *)addr);
+ ip6_compressed_string(ip6_addr, addr);
else
- ip6_string(ip6_addr, (const struct in6_addr *)addr, fmt);
+ ip6_string(ip6_addr, addr, fmt);
return string(buf, end, ip6_addr, spec);
}
* advance both strings to next white space
*/
if (*fmt == '*') {
- while (!isspace(*fmt) && *fmt)
+ while (!isspace(*fmt) && *fmt != '%' && *fmt)
fmt++;
while (!isspace(*str) && *str)
str++;
This value can be changed after boot using the
/proc/sys/vm/mmap_min_addr tunable.
+config ARCH_SUPPORTS_MEMORY_FAILURE
+ bool
+
+config MEMORY_FAILURE
+ depends on MMU
+ depends on ARCH_SUPPORTS_MEMORY_FAILURE
+ bool "Enable recovery from hardware memory errors"
+ help
+ Enables code to recover from some memory failures on systems
+ with MCA recovery. This allows a system to continue running
+ even when some of its memory has uncorrected errors. This requires
+ special hardware support and typically ECC memory.
+
+config HWPOISON_INJECT
+ tristate "Poison pages injector"
+ depends on MEMORY_FAILURE && DEBUG_KERNEL
config NOMMU_INITIAL_TRIM_EXCESS
int "Turn on mmap() excess space trimming before booting"
mmu-y := nommu.o
mmu-$(CONFIG_MMU) := fremap.o highmem.o madvise.o memory.o mincore.o \
mlock.o mmap.o mprotect.o mremap.o msync.o rmap.o \
- vmalloc.o
+ vmalloc.o pagewalk.o
obj-y := bootmem.o filemap.o mempool.o oom_kill.o fadvise.o \
maccess.o page_alloc.o page-writeback.o \
readahead.o swap.o truncate.o vmscan.o shmem.o \
prio_tree.o util.o mmzone.o vmstat.o backing-dev.o \
page_isolation.o mm_init.o mmu_context.o \
- pagewalk.o $(mmu-y)
+ $(mmu-y)
obj-y += init-mm.o
obj-$(CONFIG_BOUNCE) += bounce.o
endif
obj-$(CONFIG_QUICKLIST) += quicklist.o
obj-$(CONFIG_CGROUP_MEM_RES_CTLR) += memcontrol.o page_cgroup.o
+obj-$(CONFIG_MEMORY_FAILURE) += memory-failure.o
+obj-$(CONFIG_HWPOISON_INJECT) += hwpoison-inject.o
obj-$(CONFIG_DEBUG_KMEMLEAK) += kmemleak.o
obj-$(CONFIG_DEBUG_KMEMLEAK_TEST) += kmemleak-test.o
/*
* Lock ordering:
*
- * ->i_mmap_lock (vmtruncate)
+ * ->i_mmap_lock (truncate_pagecache)
* ->private_lock (__free_pte->__set_page_dirty_buffers)
* ->swap_lock (exclusive_swap_page, others)
* ->mapping->tree_lock
*
* ->task->proc_lock
* ->dcache_lock (proc_pid_lookup)
+ *
+ * (code doesn't rely on that order, so you could switch it around)
+ * ->tasklist_lock (memory_failure, collect_procs_ao)
+ * ->i_mmap_lock
*/
/*
}
EXPORT_SYMBOL(filemap_fault);
-struct vm_operations_struct generic_file_vm_ops = {
+const struct vm_operations_struct generic_file_vm_ops = {
.fault = filemap_fault,
};
}
}
-static struct vm_operations_struct xip_file_vm_ops = {
+static const struct vm_operations_struct xip_file_vm_ops = {
.fault = xip_file_fault,
};
#ifdef CONFIG_SYSCTL
int hugetlb_sysctl_handler(struct ctl_table *table, int write,
- struct file *file, void __user *buffer,
+ void __user *buffer,
size_t *length, loff_t *ppos)
{
struct hstate *h = &default_hstate;
table->data = &tmp;
table->maxlen = sizeof(unsigned long);
- proc_doulongvec_minmax(table, write, file, buffer, length, ppos);
+ proc_doulongvec_minmax(table, write, buffer, length, ppos);
if (write)
h->max_huge_pages = set_max_huge_pages(h, tmp);
}
int hugetlb_treat_movable_handler(struct ctl_table *table, int write,
- struct file *file, void __user *buffer,
+ void __user *buffer,
size_t *length, loff_t *ppos)
{
- proc_dointvec(table, write, file, buffer, length, ppos);
+ proc_dointvec(table, write, buffer, length, ppos);
if (hugepages_treat_as_movable)
htlb_alloc_mask = GFP_HIGHUSER_MOVABLE;
else
}
int hugetlb_overcommit_handler(struct ctl_table *table, int write,
- struct file *file, void __user *buffer,
+ void __user *buffer,
size_t *length, loff_t *ppos)
{
struct hstate *h = &default_hstate;
table->data = &tmp;
table->maxlen = sizeof(unsigned long);
- proc_doulongvec_minmax(table, write, file, buffer, length, ppos);
+ proc_doulongvec_minmax(table, write, buffer, length, ppos);
if (write) {
spin_lock(&hugetlb_lock);
return 0;
}
-struct vm_operations_struct hugetlb_vm_ops = {
+const struct vm_operations_struct hugetlb_vm_ops = {
.fault = hugetlb_vm_op_fault,
.open = hugetlb_vm_op_open,
.close = hugetlb_vm_op_close,
--- /dev/null
+/* Inject a hwpoison memory failure on a arbitary pfn */
+#include <linux/module.h>
+#include <linux/debugfs.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+
+static struct dentry *hwpoison_dir, *corrupt_pfn;
+
+static int hwpoison_inject(void *data, u64 val)
+{
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+ printk(KERN_INFO "Injecting memory failure at pfn %Lx\n", val);
+ return __memory_failure(val, 18, 0);
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(hwpoison_fops, NULL, hwpoison_inject, "%lli\n");
+
+static void pfn_inject_exit(void)
+{
+ if (hwpoison_dir)
+ debugfs_remove_recursive(hwpoison_dir);
+}
+
+static int pfn_inject_init(void)
+{
+ hwpoison_dir = debugfs_create_dir("hwpoison", NULL);
+ if (hwpoison_dir == NULL)
+ return -ENOMEM;
+ corrupt_pfn = debugfs_create_file("corrupt-pfn", 0600, hwpoison_dir,
+ NULL, &hwpoison_fops);
+ if (corrupt_pfn == NULL) {
+ pfn_inject_exit();
+ return -ENOMEM;
+ }
+ return 0;
+}
+
+module_init(pfn_inject_init);
+module_exit(pfn_inject_exit);
+MODULE_LICENSE("GPL");
#include <linux/slab.h>
#include <linux/rbtree.h>
#include <linux/mmu_notifier.h>
+#include <linux/swap.h>
#include <linux/ksm.h>
#include <asm/tlbflush.h>
static unsigned long ksm_rmap_items;
/* Limit on the number of unswappable pages used */
-static unsigned long ksm_max_kernel_pages = 2000;
+static unsigned long ksm_max_kernel_pages;
/* Number of pages ksmd should scan in one batch */
-static unsigned int ksm_thread_pages_to_scan = 200;
+static unsigned int ksm_thread_pages_to_scan = 100;
/* Milliseconds ksmd should sleep between batches */
static unsigned int ksm_thread_sleep_millisecs = 20;
#define KSM_RUN_STOP 0
#define KSM_RUN_MERGE 1
#define KSM_RUN_UNMERGE 2
-static unsigned int ksm_run = KSM_RUN_MERGE;
+static unsigned int ksm_run = KSM_RUN_STOP;
static DECLARE_WAIT_QUEUE_HEAD(ksm_thread_wait);
static DEFINE_MUTEX(ksm_thread_mutex);
sizeof(struct __struct), __alignof__(struct __struct),\
(__flags), NULL)
+static void __init ksm_init_max_kernel_pages(void)
+{
+ ksm_max_kernel_pages = nr_free_buffer_pages() / 4;
+}
+
static int __init ksm_slab_init(void)
{
rmap_item_cache = KSM_KMEM_CACHE(rmap_item, 0);
struct task_struct *ksm_thread;
int err;
+ ksm_init_max_kernel_pages();
+
err = ksm_slab_init();
if (err)
goto out;
return error;
}
+#ifdef CONFIG_MEMORY_FAILURE
+/*
+ * Error injection support for memory error handling.
+ */
+static int madvise_hwpoison(unsigned long start, unsigned long end)
+{
+ int ret = 0;
+
+ if (!capable(CAP_SYS_ADMIN))
+ return -EPERM;
+ for (; start < end; start += PAGE_SIZE) {
+ struct page *p;
+ int ret = get_user_pages(current, current->mm, start, 1,
+ 0, 0, &p, NULL);
+ if (ret != 1)
+ return ret;
+ printk(KERN_INFO "Injecting memory failure for page %lx at %lx\n",
+ page_to_pfn(p), start);
+ /* Ignore return value for now */
+ __memory_failure(page_to_pfn(p), 0, 1);
+ put_page(p);
+ }
+ return ret;
+}
+#endif
+
static long
madvise_vma(struct vm_area_struct *vma, struct vm_area_struct **prev,
unsigned long start, unsigned long end, int behavior)
int write;
size_t len;
+#ifdef CONFIG_MEMORY_FAILURE
+ if (behavior == MADV_HWPOISON)
+ return madvise_hwpoison(start, start+len_in);
+#endif
if (!madvise_behavior_valid(behavior))
return error;
#include <linux/rcupdate.h>
#include <linux/limits.h>
#include <linux/mutex.h>
+#include <linux/rbtree.h>
#include <linux/slab.h>
#include <linux/swap.h>
#include <linux/spinlock.h>
struct cgroup_subsys mem_cgroup_subsys __read_mostly;
#define MEM_CGROUP_RECLAIM_RETRIES 5
+struct mem_cgroup *root_mem_cgroup __read_mostly;
#ifdef CONFIG_CGROUP_MEM_RES_CTLR_SWAP
/* Turned on only when memory cgroup is enabled && really_do_swap_account = 1 */
#endif
static DEFINE_MUTEX(memcg_tasklist); /* can be hold under cgroup_mutex */
+#define SOFTLIMIT_EVENTS_THRESH (1000)
/*
* Statistics for memory cgroup.
MEM_CGROUP_STAT_MAPPED_FILE, /* # of pages charged as file rss */
MEM_CGROUP_STAT_PGPGIN_COUNT, /* # of pages paged in */
MEM_CGROUP_STAT_PGPGOUT_COUNT, /* # of pages paged out */
+ MEM_CGROUP_STAT_EVENTS, /* sum of pagein + pageout for internal use */
+ MEM_CGROUP_STAT_SWAPOUT, /* # of pages, swapped out */
MEM_CGROUP_STAT_NSTATS,
};
struct mem_cgroup_stat_cpu cpustat[0];
};
+static inline void
+__mem_cgroup_stat_reset_safe(struct mem_cgroup_stat_cpu *stat,
+ enum mem_cgroup_stat_index idx)
+{
+ stat->count[idx] = 0;
+}
+
+static inline s64
+__mem_cgroup_stat_read_local(struct mem_cgroup_stat_cpu *stat,
+ enum mem_cgroup_stat_index idx)
+{
+ return stat->count[idx];
+}
+
/*
* For accounting under irq disable, no need for increment preempt count.
*/
unsigned long count[NR_LRU_LISTS];
struct zone_reclaim_stat reclaim_stat;
+ struct rb_node tree_node; /* RB tree node */
+ unsigned long long usage_in_excess;/* Set to the value by which */
+ /* the soft limit is exceeded*/
+ bool on_tree;
+ struct mem_cgroup *mem; /* Back pointer, we cannot */
+ /* use container_of */
};
/* Macro for accessing counter */
#define MEM_CGROUP_ZSTAT(mz, idx) ((mz)->count[(idx)])
struct mem_cgroup_per_node *nodeinfo[MAX_NUMNODES];
};
+/*
+ * Cgroups above their limits are maintained in a RB-Tree, independent of
+ * their hierarchy representation
+ */
+
+struct mem_cgroup_tree_per_zone {
+ struct rb_root rb_root;
+ spinlock_t lock;
+};
+
+struct mem_cgroup_tree_per_node {
+ struct mem_cgroup_tree_per_zone rb_tree_per_zone[MAX_NR_ZONES];
+};
+
+struct mem_cgroup_tree {
+ struct mem_cgroup_tree_per_node *rb_tree_per_node[MAX_NUMNODES];
+};
+
+static struct mem_cgroup_tree soft_limit_tree __read_mostly;
+
/*
* The memory controller data structure. The memory controller controls both
* page cache and RSS per cgroup. We would eventually like to provide
struct mem_cgroup_stat stat;
};
+/*
+ * Maximum loops in mem_cgroup_hierarchical_reclaim(), used for soft
+ * limit reclaim to prevent infinite loops, if they ever occur.
+ */
+#define MEM_CGROUP_MAX_RECLAIM_LOOPS (100)
+#define MEM_CGROUP_MAX_SOFT_LIMIT_RECLAIM_LOOPS (2)
+
enum charge_type {
MEM_CGROUP_CHARGE_TYPE_CACHE = 0,
MEM_CGROUP_CHARGE_TYPE_MAPPED,
#define PCGF_CACHE (1UL << PCG_CACHE)
#define PCGF_USED (1UL << PCG_USED)
#define PCGF_LOCK (1UL << PCG_LOCK)
-static const unsigned long
-pcg_default_flags[NR_CHARGE_TYPE] = {
- PCGF_CACHE | PCGF_USED | PCGF_LOCK, /* File Cache */
- PCGF_USED | PCGF_LOCK, /* Anon */
- PCGF_CACHE | PCGF_USED | PCGF_LOCK, /* Shmem */
- 0, /* FORCE */
-};
+/* Not used, but added here for completeness */
+#define PCGF_ACCT (1UL << PCG_ACCT)
/* for encoding cft->private value on file */
#define _MEM (0)
#define MEMFILE_TYPE(val) (((val) >> 16) & 0xffff)
#define MEMFILE_ATTR(val) ((val) & 0xffff)
+/*
+ * Reclaim flags for mem_cgroup_hierarchical_reclaim
+ */
+#define MEM_CGROUP_RECLAIM_NOSWAP_BIT 0x0
+#define MEM_CGROUP_RECLAIM_NOSWAP (1 << MEM_CGROUP_RECLAIM_NOSWAP_BIT)
+#define MEM_CGROUP_RECLAIM_SHRINK_BIT 0x1
+#define MEM_CGROUP_RECLAIM_SHRINK (1 << MEM_CGROUP_RECLAIM_SHRINK_BIT)
+#define MEM_CGROUP_RECLAIM_SOFT_BIT 0x2
+#define MEM_CGROUP_RECLAIM_SOFT (1 << MEM_CGROUP_RECLAIM_SOFT_BIT)
+
static void mem_cgroup_get(struct mem_cgroup *mem);
static void mem_cgroup_put(struct mem_cgroup *mem);
static struct mem_cgroup *parent_mem_cgroup(struct mem_cgroup *mem);
+static struct mem_cgroup_per_zone *
+mem_cgroup_zoneinfo(struct mem_cgroup *mem, int nid, int zid)
+{
+ return &mem->info.nodeinfo[nid]->zoneinfo[zid];
+}
+
+static struct mem_cgroup_per_zone *
+page_cgroup_zoneinfo(struct page_cgroup *pc)
+{
+ struct mem_cgroup *mem = pc->mem_cgroup;
+ int nid = page_cgroup_nid(pc);
+ int zid = page_cgroup_zid(pc);
+
+ if (!mem)
+ return NULL;
+
+ return mem_cgroup_zoneinfo(mem, nid, zid);
+}
+
+static struct mem_cgroup_tree_per_zone *
+soft_limit_tree_node_zone(int nid, int zid)
+{
+ return &soft_limit_tree.rb_tree_per_node[nid]->rb_tree_per_zone[zid];
+}
+
+static struct mem_cgroup_tree_per_zone *
+soft_limit_tree_from_page(struct page *page)
+{
+ int nid = page_to_nid(page);
+ int zid = page_zonenum(page);
+
+ return &soft_limit_tree.rb_tree_per_node[nid]->rb_tree_per_zone[zid];
+}
+
+static void
+__mem_cgroup_insert_exceeded(struct mem_cgroup *mem,
+ struct mem_cgroup_per_zone *mz,
+ struct mem_cgroup_tree_per_zone *mctz,
+ unsigned long long new_usage_in_excess)
+{
+ struct rb_node **p = &mctz->rb_root.rb_node;
+ struct rb_node *parent = NULL;
+ struct mem_cgroup_per_zone *mz_node;
+
+ if (mz->on_tree)
+ return;
+
+ mz->usage_in_excess = new_usage_in_excess;
+ if (!mz->usage_in_excess)
+ return;
+ while (*p) {
+ parent = *p;
+ mz_node = rb_entry(parent, struct mem_cgroup_per_zone,
+ tree_node);
+ if (mz->usage_in_excess < mz_node->usage_in_excess)
+ p = &(*p)->rb_left;
+ /*
+ * We can't avoid mem cgroups that are over their soft
+ * limit by the same amount
+ */
+ else if (mz->usage_in_excess >= mz_node->usage_in_excess)
+ p = &(*p)->rb_right;
+ }
+ rb_link_node(&mz->tree_node, parent, p);
+ rb_insert_color(&mz->tree_node, &mctz->rb_root);
+ mz->on_tree = true;
+}
+
+static void
+__mem_cgroup_remove_exceeded(struct mem_cgroup *mem,
+ struct mem_cgroup_per_zone *mz,
+ struct mem_cgroup_tree_per_zone *mctz)
+{
+ if (!mz->on_tree)
+ return;
+ rb_erase(&mz->tree_node, &mctz->rb_root);
+ mz->on_tree = false;
+}
+
+static void
+mem_cgroup_remove_exceeded(struct mem_cgroup *mem,
+ struct mem_cgroup_per_zone *mz,
+ struct mem_cgroup_tree_per_zone *mctz)
+{
+ spin_lock(&mctz->lock);
+ __mem_cgroup_remove_exceeded(mem, mz, mctz);
+ spin_unlock(&mctz->lock);
+}
+
+static bool mem_cgroup_soft_limit_check(struct mem_cgroup *mem)
+{
+ bool ret = false;
+ int cpu;
+ s64 val;
+ struct mem_cgroup_stat_cpu *cpustat;
+
+ cpu = get_cpu();
+ cpustat = &mem->stat.cpustat[cpu];
+ val = __mem_cgroup_stat_read_local(cpustat, MEM_CGROUP_STAT_EVENTS);
+ if (unlikely(val > SOFTLIMIT_EVENTS_THRESH)) {
+ __mem_cgroup_stat_reset_safe(cpustat, MEM_CGROUP_STAT_EVENTS);
+ ret = true;
+ }
+ put_cpu();
+ return ret;
+}
+
+static void mem_cgroup_update_tree(struct mem_cgroup *mem, struct page *page)
+{
+ unsigned long long excess;
+ struct mem_cgroup_per_zone *mz;
+ struct mem_cgroup_tree_per_zone *mctz;
+ int nid = page_to_nid(page);
+ int zid = page_zonenum(page);
+ mctz = soft_limit_tree_from_page(page);
+
+ /*
+ * Necessary to update all ancestors when hierarchy is used.
+ * because their event counter is not touched.
+ */
+ for (; mem; mem = parent_mem_cgroup(mem)) {
+ mz = mem_cgroup_zoneinfo(mem, nid, zid);
+ excess = res_counter_soft_limit_excess(&mem->res);
+ /*
+ * We have to update the tree if mz is on RB-tree or
+ * mem is over its softlimit.
+ */
+ if (excess || mz->on_tree) {
+ spin_lock(&mctz->lock);
+ /* if on-tree, remove it */
+ if (mz->on_tree)
+ __mem_cgroup_remove_exceeded(mem, mz, mctz);
+ /*
+ * Insert again. mz->usage_in_excess will be updated.
+ * If excess is 0, no tree ops.
+ */
+ __mem_cgroup_insert_exceeded(mem, mz, mctz, excess);
+ spin_unlock(&mctz->lock);
+ }
+ }
+}
+
+static void mem_cgroup_remove_from_trees(struct mem_cgroup *mem)
+{
+ int node, zone;
+ struct mem_cgroup_per_zone *mz;
+ struct mem_cgroup_tree_per_zone *mctz;
+
+ for_each_node_state(node, N_POSSIBLE) {
+ for (zone = 0; zone < MAX_NR_ZONES; zone++) {
+ mz = mem_cgroup_zoneinfo(mem, node, zone);
+ mctz = soft_limit_tree_node_zone(node, zone);
+ mem_cgroup_remove_exceeded(mem, mz, mctz);
+ }
+ }
+}
+
+static inline unsigned long mem_cgroup_get_excess(struct mem_cgroup *mem)
+{
+ return res_counter_soft_limit_excess(&mem->res) >> PAGE_SHIFT;
+}
+
+static struct mem_cgroup_per_zone *
+__mem_cgroup_largest_soft_limit_node(struct mem_cgroup_tree_per_zone *mctz)
+{
+ struct rb_node *rightmost = NULL;
+ struct mem_cgroup_per_zone *mz;
+
+retry:
+ mz = NULL;
+ rightmost = rb_last(&mctz->rb_root);
+ if (!rightmost)
+ goto done; /* Nothing to reclaim from */
+
+ mz = rb_entry(rightmost, struct mem_cgroup_per_zone, tree_node);
+ /*
+ * Remove the node now but someone else can add it back,
+ * we will to add it back at the end of reclaim to its correct
+ * position in the tree.
+ */
+ __mem_cgroup_remove_exceeded(mz->mem, mz, mctz);
+ if (!res_counter_soft_limit_excess(&mz->mem->res) ||
+ !css_tryget(&mz->mem->css))
+ goto retry;
+done:
+ return mz;
+}
+
+static struct mem_cgroup_per_zone *
+mem_cgroup_largest_soft_limit_node(struct mem_cgroup_tree_per_zone *mctz)
+{
+ struct mem_cgroup_per_zone *mz;
+
+ spin_lock(&mctz->lock);
+ mz = __mem_cgroup_largest_soft_limit_node(mctz);
+ spin_unlock(&mctz->lock);
+ return mz;
+}
+
+static void mem_cgroup_swap_statistics(struct mem_cgroup *mem,
+ bool charge)
+{
+ int val = (charge) ? 1 : -1;
+ struct mem_cgroup_stat *stat = &mem->stat;
+ struct mem_cgroup_stat_cpu *cpustat;
+ int cpu = get_cpu();
+
+ cpustat = &stat->cpustat[cpu];
+ __mem_cgroup_stat_add_safe(cpustat, MEM_CGROUP_STAT_SWAPOUT, val);
+ put_cpu();
+}
+
static void mem_cgroup_charge_statistics(struct mem_cgroup *mem,
struct page_cgroup *pc,
bool charge)
{
- int val = (charge)? 1 : -1;
+ int val = (charge) ? 1 : -1;
struct mem_cgroup_stat *stat = &mem->stat;
struct mem_cgroup_stat_cpu *cpustat;
int cpu = get_cpu();
else
__mem_cgroup_stat_add_safe(cpustat,
MEM_CGROUP_STAT_PGPGOUT_COUNT, 1);
+ __mem_cgroup_stat_add_safe(cpustat, MEM_CGROUP_STAT_EVENTS, 1);
put_cpu();
}
-static struct mem_cgroup_per_zone *
-mem_cgroup_zoneinfo(struct mem_cgroup *mem, int nid, int zid)
-{
- return &mem->info.nodeinfo[nid]->zoneinfo[zid];
-}
-
-static struct mem_cgroup_per_zone *
-page_cgroup_zoneinfo(struct page_cgroup *pc)
-{
- struct mem_cgroup *mem = pc->mem_cgroup;
- int nid = page_cgroup_nid(pc);
- int zid = page_cgroup_zid(pc);
-
- if (!mem)
- return NULL;
-
- return mem_cgroup_zoneinfo(mem, nid, zid);
-}
-
static unsigned long mem_cgroup_get_local_zonestat(struct mem_cgroup *mem,
enum lru_list idx)
{
return ret;
}
+static inline bool mem_cgroup_is_root(struct mem_cgroup *mem)
+{
+ return (mem == root_mem_cgroup);
+}
+
/*
* Following LRU functions are allowed to be used without PCG_LOCK.
* Operations are called by routine of global LRU independently from memcg.
void mem_cgroup_del_lru_list(struct page *page, enum lru_list lru)
{
struct page_cgroup *pc;
- struct mem_cgroup *mem;
struct mem_cgroup_per_zone *mz;
if (mem_cgroup_disabled())
return;
pc = lookup_page_cgroup(page);
/* can happen while we handle swapcache. */
- if (list_empty(&pc->lru) || !pc->mem_cgroup)
+ if (!TestClearPageCgroupAcctLRU(pc))
return;
+ VM_BUG_ON(!pc->mem_cgroup);
/*
* We don't check PCG_USED bit. It's cleared when the "page" is finally
* removed from global LRU.
*/
mz = page_cgroup_zoneinfo(pc);
- mem = pc->mem_cgroup;
MEM_CGROUP_ZSTAT(mz, lru) -= 1;
+ if (mem_cgroup_is_root(pc->mem_cgroup))
+ return;
+ VM_BUG_ON(list_empty(&pc->lru));
list_del_init(&pc->lru);
return;
}
* For making pc->mem_cgroup visible, insert smp_rmb() here.
*/
smp_rmb();
- /* unused page is not rotated. */
- if (!PageCgroupUsed(pc))
+ /* unused or root page is not rotated. */
+ if (!PageCgroupUsed(pc) || mem_cgroup_is_root(pc->mem_cgroup))
return;
mz = page_cgroup_zoneinfo(pc);
list_move(&pc->lru, &mz->lists[lru]);
if (mem_cgroup_disabled())
return;
pc = lookup_page_cgroup(page);
+ VM_BUG_ON(PageCgroupAcctLRU(pc));
/*
* Used bit is set without atomic ops but after smp_wmb().
* For making pc->mem_cgroup visible, insert smp_rmb() here.
mz = page_cgroup_zoneinfo(pc);
MEM_CGROUP_ZSTAT(mz, lru) += 1;
+ SetPageCgroupAcctLRU(pc);
+ if (mem_cgroup_is_root(pc->mem_cgroup))
+ return;
list_add(&pc->lru, &mz->lists[lru]);
}
spin_lock_irqsave(&zone->lru_lock, flags);
/* link when the page is linked to LRU but page_cgroup isn't */
- if (PageLRU(page) && list_empty(&pc->lru))
+ if (PageLRU(page) && !PageCgroupAcctLRU(pc))
mem_cgroup_add_lru_list(page, page_lru(page));
spin_unlock_irqrestore(&zone->lru_lock, flags);
}
* If shrink==true, for avoiding to free too much, this returns immedieately.
*/
static int mem_cgroup_hierarchical_reclaim(struct mem_cgroup *root_mem,
- gfp_t gfp_mask, bool noswap, bool shrink)
+ struct zone *zone,
+ gfp_t gfp_mask,
+ unsigned long reclaim_options)
{
struct mem_cgroup *victim;
int ret, total = 0;
int loop = 0;
+ bool noswap = reclaim_options & MEM_CGROUP_RECLAIM_NOSWAP;
+ bool shrink = reclaim_options & MEM_CGROUP_RECLAIM_SHRINK;
+ bool check_soft = reclaim_options & MEM_CGROUP_RECLAIM_SOFT;
+ unsigned long excess = mem_cgroup_get_excess(root_mem);
/* If memsw_is_minimum==1, swap-out is of-no-use. */
if (root_mem->memsw_is_minimum)
noswap = true;
- while (loop < 2) {
+ while (1) {
victim = mem_cgroup_select_victim(root_mem);
- if (victim == root_mem)
+ if (victim == root_mem) {
loop++;
+ if (loop >= 2) {
+ /*
+ * If we have not been able to reclaim
+ * anything, it might because there are
+ * no reclaimable pages under this hierarchy
+ */
+ if (!check_soft || !total) {
+ css_put(&victim->css);
+ break;
+ }
+ /*
+ * We want to do more targetted reclaim.
+ * excess >> 2 is not to excessive so as to
+ * reclaim too much, nor too less that we keep
+ * coming back to reclaim from this cgroup
+ */
+ if (total >= (excess >> 2) ||
+ (loop > MEM_CGROUP_MAX_RECLAIM_LOOPS)) {
+ css_put(&victim->css);
+ break;
+ }
+ }
+ }
if (!mem_cgroup_local_usage(&victim->stat)) {
/* this cgroup's local usage == 0 */
css_put(&victim->css);
continue;
}
/* we use swappiness of local cgroup */
- ret = try_to_free_mem_cgroup_pages(victim, gfp_mask, noswap,
- get_swappiness(victim));
+ if (check_soft)
+ ret = mem_cgroup_shrink_node_zone(victim, gfp_mask,
+ noswap, get_swappiness(victim), zone,
+ zone->zone_pgdat->node_id);
+ else
+ ret = try_to_free_mem_cgroup_pages(victim, gfp_mask,
+ noswap, get_swappiness(victim));
css_put(&victim->css);
/*
* At shrinking usage, we can't check we should stop here or
if (shrink)
return ret;
total += ret;
- if (mem_cgroup_check_under_limit(root_mem))
+ if (check_soft) {
+ if (res_counter_check_under_soft_limit(&root_mem->res))
+ return total;
+ } else if (mem_cgroup_check_under_limit(root_mem))
return 1 + total;
}
return total;
*/
static int __mem_cgroup_try_charge(struct mm_struct *mm,
gfp_t gfp_mask, struct mem_cgroup **memcg,
- bool oom)
+ bool oom, struct page *page)
{
struct mem_cgroup *mem, *mem_over_limit;
int nr_retries = MEM_CGROUP_RECLAIM_RETRIES;
VM_BUG_ON(css_is_removed(&mem->css));
while (1) {
- int ret;
- bool noswap = false;
+ int ret = 0;
+ unsigned long flags = 0;
+ if (mem_cgroup_is_root(mem))
+ goto done;
ret = res_counter_charge(&mem->res, PAGE_SIZE, &fail_res);
if (likely(!ret)) {
if (!do_swap_account)
break;
/* mem+swap counter fails */
res_counter_uncharge(&mem->res, PAGE_SIZE);
- noswap = true;
+ flags |= MEM_CGROUP_RECLAIM_NOSWAP;
mem_over_limit = mem_cgroup_from_res_counter(fail_res,
memsw);
} else
if (!(gfp_mask & __GFP_WAIT))
goto nomem;
- ret = mem_cgroup_hierarchical_reclaim(mem_over_limit, gfp_mask,
- noswap, false);
+ ret = mem_cgroup_hierarchical_reclaim(mem_over_limit, NULL,
+ gfp_mask, flags);
if (ret)
continue;
goto nomem;
}
}
+ /*
+ * Insert ancestor (and ancestor's ancestors), to softlimit RB-tree.
+ * if they exceeds softlimit.
+ */
+ if (mem_cgroup_soft_limit_check(mem))
+ mem_cgroup_update_tree(mem, page);
+done:
return 0;
nomem:
css_put(&mem->css);
return -ENOMEM;
}
-
/*
* A helper function to get mem_cgroup from ID. must be called under
* rcu_read_lock(). The caller must check css_is_removed() or some if
lock_page_cgroup(pc);
if (unlikely(PageCgroupUsed(pc))) {
unlock_page_cgroup(pc);
- res_counter_uncharge(&mem->res, PAGE_SIZE);
- if (do_swap_account)
- res_counter_uncharge(&mem->memsw, PAGE_SIZE);
+ if (!mem_cgroup_is_root(mem)) {
+ res_counter_uncharge(&mem->res, PAGE_SIZE);
+ if (do_swap_account)
+ res_counter_uncharge(&mem->memsw, PAGE_SIZE);
+ }
css_put(&mem->css);
return;
}
+
pc->mem_cgroup = mem;
+ /*
+ * We access a page_cgroup asynchronously without lock_page_cgroup().
+ * Especially when a page_cgroup is taken from a page, pc->mem_cgroup
+ * is accessed after testing USED bit. To make pc->mem_cgroup visible
+ * before USED bit, we need memory barrier here.
+ * See mem_cgroup_add_lru_list(), etc.
+ */
smp_wmb();
- pc->flags = pcg_default_flags[ctype];
+ switch (ctype) {
+ case MEM_CGROUP_CHARGE_TYPE_CACHE:
+ case MEM_CGROUP_CHARGE_TYPE_SHMEM:
+ SetPageCgroupCache(pc);
+ SetPageCgroupUsed(pc);
+ break;
+ case MEM_CGROUP_CHARGE_TYPE_MAPPED:
+ ClearPageCgroupCache(pc);
+ SetPageCgroupUsed(pc);
+ break;
+ default:
+ break;
+ }
mem_cgroup_charge_statistics(mem, pc, true);
if (pc->mem_cgroup != from)
goto out;
- res_counter_uncharge(&from->res, PAGE_SIZE);
+ if (!mem_cgroup_is_root(from))
+ res_counter_uncharge(&from->res, PAGE_SIZE);
mem_cgroup_charge_statistics(from, pc, false);
page = pc->page;
1);
}
- if (do_swap_account)
+ if (do_swap_account && !mem_cgroup_is_root(from))
res_counter_uncharge(&from->memsw, PAGE_SIZE);
css_put(&from->css);
parent = mem_cgroup_from_cont(pcg);
- ret = __mem_cgroup_try_charge(NULL, gfp_mask, &parent, false);
+ ret = __mem_cgroup_try_charge(NULL, gfp_mask, &parent, false, page);
if (ret || !parent)
return ret;
/* drop extra refcnt by try_charge() */
css_put(&parent->css);
/* uncharge if move fails */
- res_counter_uncharge(&parent->res, PAGE_SIZE);
- if (do_swap_account)
- res_counter_uncharge(&parent->memsw, PAGE_SIZE);
+ if (!mem_cgroup_is_root(parent)) {
+ res_counter_uncharge(&parent->res, PAGE_SIZE);
+ if (do_swap_account)
+ res_counter_uncharge(&parent->memsw, PAGE_SIZE);
+ }
return ret;
}
prefetchw(pc);
mem = memcg;
- ret = __mem_cgroup_try_charge(mm, gfp_mask, &mem, true);
+ ret = __mem_cgroup_try_charge(mm, gfp_mask, &mem, true, page);
if (ret || !mem)
return ret;
if (!mem)
goto charge_cur_mm;
*ptr = mem;
- ret = __mem_cgroup_try_charge(NULL, mask, ptr, true);
+ ret = __mem_cgroup_try_charge(NULL, mask, ptr, true, page);
/* drop extra refcnt from tryget */
css_put(&mem->css);
return ret;
charge_cur_mm:
if (unlikely(!mm))
mm = &init_mm;
- return __mem_cgroup_try_charge(mm, mask, ptr, true);
+ return __mem_cgroup_try_charge(mm, mask, ptr, true, page);
}
static void
* This recorded memcg can be obsolete one. So, avoid
* calling css_tryget
*/
- res_counter_uncharge(&memcg->memsw, PAGE_SIZE);
+ if (!mem_cgroup_is_root(memcg))
+ res_counter_uncharge(&memcg->memsw, PAGE_SIZE);
+ mem_cgroup_swap_statistics(memcg, false);
mem_cgroup_put(memcg);
}
rcu_read_unlock();
return;
if (!mem)
return;
- res_counter_uncharge(&mem->res, PAGE_SIZE);
- if (do_swap_account)
- res_counter_uncharge(&mem->memsw, PAGE_SIZE);
+ if (!mem_cgroup_is_root(mem)) {
+ res_counter_uncharge(&mem->res, PAGE_SIZE);
+ if (do_swap_account)
+ res_counter_uncharge(&mem->memsw, PAGE_SIZE);
+ }
css_put(&mem->css);
}
break;
}
- res_counter_uncharge(&mem->res, PAGE_SIZE);
- if (do_swap_account && (ctype != MEM_CGROUP_CHARGE_TYPE_SWAPOUT))
- res_counter_uncharge(&mem->memsw, PAGE_SIZE);
+ if (!mem_cgroup_is_root(mem)) {
+ res_counter_uncharge(&mem->res, PAGE_SIZE);
+ if (do_swap_account &&
+ (ctype != MEM_CGROUP_CHARGE_TYPE_SWAPOUT))
+ res_counter_uncharge(&mem->memsw, PAGE_SIZE);
+ }
+ if (ctype == MEM_CGROUP_CHARGE_TYPE_SWAPOUT)
+ mem_cgroup_swap_statistics(mem, true);
mem_cgroup_charge_statistics(mem, pc, false);
ClearPageCgroupUsed(pc);
mz = page_cgroup_zoneinfo(pc);
unlock_page_cgroup(pc);
+ if (mem_cgroup_soft_limit_check(mem))
+ mem_cgroup_update_tree(mem, page);
/* at swapout, this memcg will be accessed to record to swap */
if (ctype != MEM_CGROUP_CHARGE_TYPE_SWAPOUT)
css_put(&mem->css);
* We uncharge this because swap is freed.
* This memcg can be obsolete one. We avoid calling css_tryget
*/
- res_counter_uncharge(&memcg->memsw, PAGE_SIZE);
+ if (!mem_cgroup_is_root(memcg))
+ res_counter_uncharge(&memcg->memsw, PAGE_SIZE);
+ mem_cgroup_swap_statistics(memcg, false);
mem_cgroup_put(memcg);
}
rcu_read_unlock();
unlock_page_cgroup(pc);
if (mem) {
- ret = __mem_cgroup_try_charge(NULL, GFP_KERNEL, &mem, false);
+ ret = __mem_cgroup_try_charge(NULL, GFP_KERNEL, &mem, false,
+ page);
css_put(&mem->css);
}
*ptr = mem;
if (!ret)
break;
- progress = mem_cgroup_hierarchical_reclaim(memcg, GFP_KERNEL,
- false, true);
+ progress = mem_cgroup_hierarchical_reclaim(memcg, NULL,
+ GFP_KERNEL,
+ MEM_CGROUP_RECLAIM_SHRINK);
curusage = res_counter_read_u64(&memcg->res, RES_USAGE);
/* Usage is reduced ? */
if (curusage >= oldusage)
if (!ret)
break;
- mem_cgroup_hierarchical_reclaim(memcg, GFP_KERNEL, true, true);
+ mem_cgroup_hierarchical_reclaim(memcg, NULL, GFP_KERNEL,
+ MEM_CGROUP_RECLAIM_NOSWAP |
+ MEM_CGROUP_RECLAIM_SHRINK);
curusage = res_counter_read_u64(&memcg->memsw, RES_USAGE);
/* Usage is reduced ? */
if (curusage >= oldusage)
return ret;
}
+unsigned long mem_cgroup_soft_limit_reclaim(struct zone *zone, int order,
+ gfp_t gfp_mask, int nid,
+ int zid)
+{
+ unsigned long nr_reclaimed = 0;
+ struct mem_cgroup_per_zone *mz, *next_mz = NULL;
+ unsigned long reclaimed;
+ int loop = 0;
+ struct mem_cgroup_tree_per_zone *mctz;
+ unsigned long long excess;
+
+ if (order > 0)
+ return 0;
+
+ mctz = soft_limit_tree_node_zone(nid, zid);
+ /*
+ * This loop can run a while, specially if mem_cgroup's continuously
+ * keep exceeding their soft limit and putting the system under
+ * pressure
+ */
+ do {
+ if (next_mz)
+ mz = next_mz;
+ else
+ mz = mem_cgroup_largest_soft_limit_node(mctz);
+ if (!mz)
+ break;
+
+ reclaimed = mem_cgroup_hierarchical_reclaim(mz->mem, zone,
+ gfp_mask,
+ MEM_CGROUP_RECLAIM_SOFT);
+ nr_reclaimed += reclaimed;
+ spin_lock(&mctz->lock);
+
+ /*
+ * If we failed to reclaim anything from this memory cgroup
+ * it is time to move on to the next cgroup
+ */
+ next_mz = NULL;
+ if (!reclaimed) {
+ do {
+ /*
+ * Loop until we find yet another one.
+ *
+ * By the time we get the soft_limit lock
+ * again, someone might have aded the
+ * group back on the RB tree. Iterate to
+ * make sure we get a different mem.
+ * mem_cgroup_largest_soft_limit_node returns
+ * NULL if no other cgroup is present on
+ * the tree
+ */
+ next_mz =
+ __mem_cgroup_largest_soft_limit_node(mctz);
+ if (next_mz == mz) {
+ css_put(&next_mz->mem->css);
+ next_mz = NULL;
+ } else /* next_mz == NULL or other memcg */
+ break;
+ } while (1);
+ }
+ __mem_cgroup_remove_exceeded(mz->mem, mz, mctz);
+ excess = res_counter_soft_limit_excess(&mz->mem->res);
+ /*
+ * One school of thought says that we should not add
+ * back the node to the tree if reclaim returns 0.
+ * But our reclaim could return 0, simply because due
+ * to priority we are exposing a smaller subset of
+ * memory to reclaim from. Consider this as a longer
+ * term TODO.
+ */
+ /* If excess == 0, no tree ops */
+ __mem_cgroup_insert_exceeded(mz->mem, mz, mctz, excess);
+ spin_unlock(&mctz->lock);
+ css_put(&mz->mem->css);
+ loop++;
+ /*
+ * Could not reclaim anything and there are no more
+ * mem cgroups to try or we seem to be looping without
+ * reclaiming anything.
+ */
+ if (!nr_reclaimed &&
+ (next_mz == NULL ||
+ loop > MEM_CGROUP_MAX_SOFT_LIMIT_RECLAIM_LOOPS))
+ break;
+ } while (!nr_reclaimed);
+ if (next_mz)
+ css_put(&next_mz->mem->css);
+ return nr_reclaimed;
+}
+
/*
* This routine traverse page_cgroup in given list and drop them all.
* *And* this routine doesn't reclaim page itself, just removes page_cgroup.
return retval;
}
+struct mem_cgroup_idx_data {
+ s64 val;
+ enum mem_cgroup_stat_index idx;
+};
+
+static int
+mem_cgroup_get_idx_stat(struct mem_cgroup *mem, void *data)
+{
+ struct mem_cgroup_idx_data *d = data;
+ d->val += mem_cgroup_read_stat(&mem->stat, d->idx);
+ return 0;
+}
+
+static void
+mem_cgroup_get_recursive_idx_stat(struct mem_cgroup *mem,
+ enum mem_cgroup_stat_index idx, s64 *val)
+{
+ struct mem_cgroup_idx_data d;
+ d.idx = idx;
+ d.val = 0;
+ mem_cgroup_walk_tree(mem, &d, mem_cgroup_get_idx_stat);
+ *val = d.val;
+}
+
static u64 mem_cgroup_read(struct cgroup *cont, struct cftype *cft)
{
struct mem_cgroup *mem = mem_cgroup_from_cont(cont);
- u64 val = 0;
+ u64 idx_val, val;
int type, name;
type = MEMFILE_TYPE(cft->private);
name = MEMFILE_ATTR(cft->private);
switch (type) {
case _MEM:
- val = res_counter_read_u64(&mem->res, name);
+ if (name == RES_USAGE && mem_cgroup_is_root(mem)) {
+ mem_cgroup_get_recursive_idx_stat(mem,
+ MEM_CGROUP_STAT_CACHE, &idx_val);
+ val = idx_val;
+ mem_cgroup_get_recursive_idx_stat(mem,
+ MEM_CGROUP_STAT_RSS, &idx_val);
+ val += idx_val;
+ val <<= PAGE_SHIFT;
+ } else
+ val = res_counter_read_u64(&mem->res, name);
break;
case _MEMSWAP:
- val = res_counter_read_u64(&mem->memsw, name);
+ if (name == RES_USAGE && mem_cgroup_is_root(mem)) {
+ mem_cgroup_get_recursive_idx_stat(mem,
+ MEM_CGROUP_STAT_CACHE, &idx_val);
+ val = idx_val;
+ mem_cgroup_get_recursive_idx_stat(mem,
+ MEM_CGROUP_STAT_RSS, &idx_val);
+ val += idx_val;
+ mem_cgroup_get_recursive_idx_stat(mem,
+ MEM_CGROUP_STAT_SWAPOUT, &idx_val);
+ val <<= PAGE_SHIFT;
+ } else
+ val = res_counter_read_u64(&mem->memsw, name);
break;
default:
BUG();
name = MEMFILE_ATTR(cft->private);
switch (name) {
case RES_LIMIT:
+ if (mem_cgroup_is_root(memcg)) { /* Can't set limit on root */
+ ret = -EINVAL;
+ break;
+ }
/* This function does all necessary parse...reuse it */
ret = res_counter_memparse_write_strategy(buffer, &val);
if (ret)
else
ret = mem_cgroup_resize_memsw_limit(memcg, val);
break;
+ case RES_SOFT_LIMIT:
+ ret = res_counter_memparse_write_strategy(buffer, &val);
+ if (ret)
+ break;
+ /*
+ * For memsw, soft limits are hard to implement in terms
+ * of semantics, for now, we support soft limits for
+ * control without swap
+ */
+ if (type == _MEM)
+ ret = res_counter_set_soft_limit(&memcg->res, val);
+ else
+ ret = -EINVAL;
+ break;
default:
ret = -EINVAL; /* should be BUG() ? */
break;
res_counter_reset_failcnt(&mem->memsw);
break;
}
+
return 0;
}
MCS_MAPPED_FILE,
MCS_PGPGIN,
MCS_PGPGOUT,
+ MCS_SWAP,
MCS_INACTIVE_ANON,
MCS_ACTIVE_ANON,
MCS_INACTIVE_FILE,
{"mapped_file", "total_mapped_file"},
{"pgpgin", "total_pgpgin"},
{"pgpgout", "total_pgpgout"},
+ {"swap", "total_swap"},
{"inactive_anon", "total_inactive_anon"},
{"active_anon", "total_active_anon"},
{"inactive_file", "total_inactive_file"},
s->stat[MCS_PGPGIN] += val;
val = mem_cgroup_read_stat(&mem->stat, MEM_CGROUP_STAT_PGPGOUT_COUNT);
s->stat[MCS_PGPGOUT] += val;
+ if (do_swap_account) {
+ val = mem_cgroup_read_stat(&mem->stat, MEM_CGROUP_STAT_SWAPOUT);
+ s->stat[MCS_SWAP] += val * PAGE_SIZE;
+ }
/* per zone stat */
val = mem_cgroup_get_local_zonestat(mem, LRU_INACTIVE_ANON);
memset(&mystat, 0, sizeof(mystat));
mem_cgroup_get_local_stat(mem_cont, &mystat);
- for (i = 0; i < NR_MCS_STAT; i++)
+ for (i = 0; i < NR_MCS_STAT; i++) {
+ if (i == MCS_SWAP && !do_swap_account)
+ continue;
cb->fill(cb, memcg_stat_strings[i].local_name, mystat.stat[i]);
+ }
/* Hierarchical information */
{
memset(&mystat, 0, sizeof(mystat));
mem_cgroup_get_total_stat(mem_cont, &mystat);
- for (i = 0; i < NR_MCS_STAT; i++)
+ for (i = 0; i < NR_MCS_STAT; i++) {
+ if (i == MCS_SWAP && !do_swap_account)
+ continue;
cb->fill(cb, memcg_stat_strings[i].total_name, mystat.stat[i]);
-
+ }
#ifdef CONFIG_DEBUG_VM
cb->fill(cb, "inactive_ratio", calc_inactive_ratio(mem_cont, NULL));
.write_string = mem_cgroup_write,
.read_u64 = mem_cgroup_read,
},
+ {
+ .name = "soft_limit_in_bytes",
+ .private = MEMFILE_PRIVATE(_MEM, RES_SOFT_LIMIT),
+ .write_string = mem_cgroup_write,
+ .read_u64 = mem_cgroup_read,
+ },
{
.name = "failcnt",
.private = MEMFILE_PRIVATE(_MEM, RES_FAILCNT),
mz = &pn->zoneinfo[zone];
for_each_lru(l)
INIT_LIST_HEAD(&mz->lists[l]);
+ mz->usage_in_excess = 0;
+ mz->on_tree = false;
+ mz->mem = mem;
}
return 0;
}
{
int node;
+ mem_cgroup_remove_from_trees(mem);
free_css_id(&mem_cgroup_subsys, &mem->css);
for_each_node_state(node, N_POSSIBLE)
}
#endif
+static int mem_cgroup_soft_limit_tree_init(void)
+{
+ struct mem_cgroup_tree_per_node *rtpn;
+ struct mem_cgroup_tree_per_zone *rtpz;
+ int tmp, node, zone;
+
+ for_each_node_state(node, N_POSSIBLE) {
+ tmp = node;
+ if (!node_state(node, N_NORMAL_MEMORY))
+ tmp = -1;
+ rtpn = kzalloc_node(sizeof(*rtpn), GFP_KERNEL, tmp);
+ if (!rtpn)
+ return 1;
+
+ soft_limit_tree.rb_tree_per_node[node] = rtpn;
+
+ for (zone = 0; zone < MAX_NR_ZONES; zone++) {
+ rtpz = &rtpn->rb_tree_per_zone[zone];
+ rtpz->rb_root = RB_ROOT;
+ spin_lock_init(&rtpz->lock);
+ }
+ }
+ return 0;
+}
+
static struct cgroup_subsys_state * __ref
mem_cgroup_create(struct cgroup_subsys *ss, struct cgroup *cont)
{
for_each_node_state(node, N_POSSIBLE)
if (alloc_mem_cgroup_per_zone_info(mem, node))
goto free_out;
+
/* root ? */
if (cont->parent == NULL) {
enable_swap_cgroup();
parent = NULL;
+ root_mem_cgroup = mem;
+ if (mem_cgroup_soft_limit_tree_init())
+ goto free_out;
+
} else {
parent = mem_cgroup_from_cont(cont->parent);
mem->use_hierarchy = parent->use_hierarchy;
return &mem->css;
free_out:
__mem_cgroup_free(mem);
+ root_mem_cgroup = NULL;
return ERR_PTR(error);
}
static void mem_cgroup_move_task(struct cgroup_subsys *ss,
struct cgroup *cont,
struct cgroup *old_cont,
- struct task_struct *p)
+ struct task_struct *p,
+ bool threadgroup)
{
mutex_lock(&memcg_tasklist);
/*
--- /dev/null
+/*
+ * Copyright (C) 2008, 2009 Intel Corporation
+ * Authors: Andi Kleen, Fengguang Wu
+ *
+ * This software may be redistributed and/or modified under the terms of
+ * the GNU General Public License ("GPL") version 2 only as published by the
+ * Free Software Foundation.
+ *
+ * High level machine check handler. Handles pages reported by the
+ * hardware as being corrupted usually due to a 2bit ECC memory or cache
+ * failure.
+ *
+ * Handles page cache pages in various states. The tricky part
+ * here is that we can access any page asynchronous to other VM
+ * users, because memory failures could happen anytime and anywhere,
+ * possibly violating some of their assumptions. This is why this code
+ * has to be extremely careful. Generally it tries to use normal locking
+ * rules, as in get the standard locks, even if that means the
+ * error handling takes potentially a long time.
+ *
+ * The operation to map back from RMAP chains to processes has to walk
+ * the complete process list and has non linear complexity with the number
+ * mappings. In short it can be quite slow. But since memory corruptions
+ * are rare we hope to get away with this.
+ */
+
+/*
+ * Notebook:
+ * - hugetlb needs more code
+ * - kcore/oldmem/vmcore/mem/kmem check for hwpoison pages
+ * - pass bad pages to kdump next kernel
+ */
+#define DEBUG 1 /* remove me in 2.6.34 */
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/page-flags.h>
+#include <linux/sched.h>
+#include <linux/rmap.h>
+#include <linux/pagemap.h>
+#include <linux/swap.h>
+#include <linux/backing-dev.h>
+#include "internal.h"
+
+int sysctl_memory_failure_early_kill __read_mostly = 0;
+
+int sysctl_memory_failure_recovery __read_mostly = 1;
+
+atomic_long_t mce_bad_pages __read_mostly = ATOMIC_LONG_INIT(0);
+
+/*
+ * Send all the processes who have the page mapped an ``action optional''
+ * signal.
+ */
+static int kill_proc_ao(struct task_struct *t, unsigned long addr, int trapno,
+ unsigned long pfn)
+{
+ struct siginfo si;
+ int ret;
+
+ printk(KERN_ERR
+ "MCE %#lx: Killing %s:%d early due to hardware memory corruption\n",
+ pfn, t->comm, t->pid);
+ si.si_signo = SIGBUS;
+ si.si_errno = 0;
+ si.si_code = BUS_MCEERR_AO;
+ si.si_addr = (void *)addr;
+#ifdef __ARCH_SI_TRAPNO
+ si.si_trapno = trapno;
+#endif
+ si.si_addr_lsb = PAGE_SHIFT;
+ /*
+ * Don't use force here, it's convenient if the signal
+ * can be temporarily blocked.
+ * This could cause a loop when the user sets SIGBUS
+ * to SIG_IGN, but hopefully noone will do that?
+ */
+ ret = send_sig_info(SIGBUS, &si, t); /* synchronous? */
+ if (ret < 0)
+ printk(KERN_INFO "MCE: Error sending signal to %s:%d: %d\n",
+ t->comm, t->pid, ret);
+ return ret;
+}
+
+/*
+ * Kill all processes that have a poisoned page mapped and then isolate
+ * the page.
+ *
+ * General strategy:
+ * Find all processes having the page mapped and kill them.
+ * But we keep a page reference around so that the page is not
+ * actually freed yet.
+ * Then stash the page away
+ *
+ * There's no convenient way to get back to mapped processes
+ * from the VMAs. So do a brute-force search over all
+ * running processes.
+ *
+ * Remember that machine checks are not common (or rather
+ * if they are common you have other problems), so this shouldn't
+ * be a performance issue.
+ *
+ * Also there are some races possible while we get from the
+ * error detection to actually handle it.
+ */
+
+struct to_kill {
+ struct list_head nd;
+ struct task_struct *tsk;
+ unsigned long addr;
+ unsigned addr_valid:1;
+};
+
+/*
+ * Failure handling: if we can't find or can't kill a process there's
+ * not much we can do. We just print a message and ignore otherwise.
+ */
+
+/*
+ * Schedule a process for later kill.
+ * Uses GFP_ATOMIC allocations to avoid potential recursions in the VM.
+ * TBD would GFP_NOIO be enough?
+ */
+static void add_to_kill(struct task_struct *tsk, struct page *p,
+ struct vm_area_struct *vma,
+ struct list_head *to_kill,
+ struct to_kill **tkc)
+{
+ struct to_kill *tk;
+
+ if (*tkc) {
+ tk = *tkc;
+ *tkc = NULL;
+ } else {
+ tk = kmalloc(sizeof(struct to_kill), GFP_ATOMIC);
+ if (!tk) {
+ printk(KERN_ERR
+ "MCE: Out of memory while machine check handling\n");
+ return;
+ }
+ }
+ tk->addr = page_address_in_vma(p, vma);
+ tk->addr_valid = 1;
+
+ /*
+ * In theory we don't have to kill when the page was
+ * munmaped. But it could be also a mremap. Since that's
+ * likely very rare kill anyways just out of paranoia, but use
+ * a SIGKILL because the error is not contained anymore.
+ */
+ if (tk->addr == -EFAULT) {
+ pr_debug("MCE: Unable to find user space address %lx in %s\n",
+ page_to_pfn(p), tsk->comm);
+ tk->addr_valid = 0;
+ }
+ get_task_struct(tsk);
+ tk->tsk = tsk;
+ list_add_tail(&tk->nd, to_kill);
+}
+
+/*
+ * Kill the processes that have been collected earlier.
+ *
+ * Only do anything when DOIT is set, otherwise just free the list
+ * (this is used for clean pages which do not need killing)
+ * Also when FAIL is set do a force kill because something went
+ * wrong earlier.
+ */
+static void kill_procs_ao(struct list_head *to_kill, int doit, int trapno,
+ int fail, unsigned long pfn)
+{
+ struct to_kill *tk, *next;
+
+ list_for_each_entry_safe (tk, next, to_kill, nd) {
+ if (doit) {
+ /*
+ * In case something went wrong with munmaping
+ * make sure the process doesn't catch the
+ * signal and then access the memory. Just kill it.
+ * the signal handlers
+ */
+ if (fail || tk->addr_valid == 0) {
+ printk(KERN_ERR
+ "MCE %#lx: forcibly killing %s:%d because of failure to unmap corrupted page\n",
+ pfn, tk->tsk->comm, tk->tsk->pid);
+ force_sig(SIGKILL, tk->tsk);
+ }
+
+ /*
+ * In theory the process could have mapped
+ * something else on the address in-between. We could
+ * check for that, but we need to tell the
+ * process anyways.
+ */
+ else if (kill_proc_ao(tk->tsk, tk->addr, trapno,
+ pfn) < 0)
+ printk(KERN_ERR
+ "MCE %#lx: Cannot send advisory machine check signal to %s:%d\n",
+ pfn, tk->tsk->comm, tk->tsk->pid);
+ }
+ put_task_struct(tk->tsk);
+ kfree(tk);
+ }
+}
+
+static int task_early_kill(struct task_struct *tsk)
+{
+ if (!tsk->mm)
+ return 0;
+ if (tsk->flags & PF_MCE_PROCESS)
+ return !!(tsk->flags & PF_MCE_EARLY);
+ return sysctl_memory_failure_early_kill;
+}
+
+/*
+ * Collect processes when the error hit an anonymous page.
+ */
+static void collect_procs_anon(struct page *page, struct list_head *to_kill,
+ struct to_kill **tkc)
+{
+ struct vm_area_struct *vma;
+ struct task_struct *tsk;
+ struct anon_vma *av;
+
+ read_lock(&tasklist_lock);
+ av = page_lock_anon_vma(page);
+ if (av == NULL) /* Not actually mapped anymore */
+ goto out;
+ for_each_process (tsk) {
+ if (!task_early_kill(tsk))
+ continue;
+ list_for_each_entry (vma, &av->head, anon_vma_node) {
+ if (!page_mapped_in_vma(page, vma))
+ continue;
+ if (vma->vm_mm == tsk->mm)
+ add_to_kill(tsk, page, vma, to_kill, tkc);
+ }
+ }
+ page_unlock_anon_vma(av);
+out:
+ read_unlock(&tasklist_lock);
+}
+
+/*
+ * Collect processes when the error hit a file mapped page.
+ */
+static void collect_procs_file(struct page *page, struct list_head *to_kill,
+ struct to_kill **tkc)
+{
+ struct vm_area_struct *vma;
+ struct task_struct *tsk;
+ struct prio_tree_iter iter;
+ struct address_space *mapping = page->mapping;
+
+ /*
+ * A note on the locking order between the two locks.
+ * We don't rely on this particular order.
+ * If you have some other code that needs a different order
+ * feel free to switch them around. Or add a reverse link
+ * from mm_struct to task_struct, then this could be all
+ * done without taking tasklist_lock and looping over all tasks.
+ */
+
+ read_lock(&tasklist_lock);
+ spin_lock(&mapping->i_mmap_lock);
+ for_each_process(tsk) {
+ pgoff_t pgoff = page->index << (PAGE_CACHE_SHIFT - PAGE_SHIFT);
+
+ if (!task_early_kill(tsk))
+ continue;
+
+ vma_prio_tree_foreach(vma, &iter, &mapping->i_mmap, pgoff,
+ pgoff) {
+ /*
+ * Send early kill signal to tasks where a vma covers
+ * the page but the corrupted page is not necessarily
+ * mapped it in its pte.
+ * Assume applications who requested early kill want
+ * to be informed of all such data corruptions.
+ */
+ if (vma->vm_mm == tsk->mm)
+ add_to_kill(tsk, page, vma, to_kill, tkc);
+ }
+ }
+ spin_unlock(&mapping->i_mmap_lock);
+ read_unlock(&tasklist_lock);
+}
+
+/*
+ * Collect the processes who have the corrupted page mapped to kill.
+ * This is done in two steps for locking reasons.
+ * First preallocate one tokill structure outside the spin locks,
+ * so that we can kill at least one process reasonably reliable.
+ */
+static void collect_procs(struct page *page, struct list_head *tokill)
+{
+ struct to_kill *tk;
+
+ if (!page->mapping)
+ return;
+
+ tk = kmalloc(sizeof(struct to_kill), GFP_NOIO);
+ if (!tk)
+ return;
+ if (PageAnon(page))
+ collect_procs_anon(page, tokill, &tk);
+ else
+ collect_procs_file(page, tokill, &tk);
+ kfree(tk);
+}
+
+/*
+ * Error handlers for various types of pages.
+ */
+
+enum outcome {
+ FAILED, /* Error handling failed */
+ DELAYED, /* Will be handled later */
+ IGNORED, /* Error safely ignored */
+ RECOVERED, /* Successfully recovered */
+};
+
+static const char *action_name[] = {
+ [FAILED] = "Failed",
+ [DELAYED] = "Delayed",
+ [IGNORED] = "Ignored",
+ [RECOVERED] = "Recovered",
+};
+
+/*
+ * Error hit kernel page.
+ * Do nothing, try to be lucky and not touch this instead. For a few cases we
+ * could be more sophisticated.
+ */
+static int me_kernel(struct page *p, unsigned long pfn)
+{
+ return DELAYED;
+}
+
+/*
+ * Already poisoned page.
+ */
+static int me_ignore(struct page *p, unsigned long pfn)
+{
+ return IGNORED;
+}
+
+/*
+ * Page in unknown state. Do nothing.
+ */
+static int me_unknown(struct page *p, unsigned long pfn)
+{
+ printk(KERN_ERR "MCE %#lx: Unknown page state\n", pfn);
+ return FAILED;
+}
+
+/*
+ * Free memory
+ */
+static int me_free(struct page *p, unsigned long pfn)
+{
+ return DELAYED;
+}
+
+/*
+ * Clean (or cleaned) page cache page.
+ */
+static int me_pagecache_clean(struct page *p, unsigned long pfn)
+{
+ int err;
+ int ret = FAILED;
+ struct address_space *mapping;
+
+ if (!isolate_lru_page(p))
+ page_cache_release(p);
+
+ /*
+ * For anonymous pages we're done the only reference left
+ * should be the one m_f() holds.
+ */
+ if (PageAnon(p))
+ return RECOVERED;
+
+ /*
+ * Now truncate the page in the page cache. This is really
+ * more like a "temporary hole punch"
+ * Don't do this for block devices when someone else
+ * has a reference, because it could be file system metadata
+ * and that's not safe to truncate.
+ */
+ mapping = page_mapping(p);
+ if (!mapping) {
+ /*
+ * Page has been teared down in the meanwhile
+ */
+ return FAILED;
+ }
+
+ /*
+ * Truncation is a bit tricky. Enable it per file system for now.
+ *
+ * Open: to take i_mutex or not for this? Right now we don't.
+ */
+ if (mapping->a_ops->error_remove_page) {
+ err = mapping->a_ops->error_remove_page(mapping, p);
+ if (err != 0) {
+ printk(KERN_INFO "MCE %#lx: Failed to punch page: %d\n",
+ pfn, err);
+ } else if (page_has_private(p) &&
+ !try_to_release_page(p, GFP_NOIO)) {
+ pr_debug("MCE %#lx: failed to release buffers\n", pfn);
+ } else {
+ ret = RECOVERED;
+ }
+ } else {
+ /*
+ * If the file system doesn't support it just invalidate
+ * This fails on dirty or anything with private pages
+ */
+ if (invalidate_inode_page(p))
+ ret = RECOVERED;
+ else
+ printk(KERN_INFO "MCE %#lx: Failed to invalidate\n",
+ pfn);
+ }
+ return ret;
+}
+
+/*
+ * Dirty cache page page
+ * Issues: when the error hit a hole page the error is not properly
+ * propagated.
+ */
+static int me_pagecache_dirty(struct page *p, unsigned long pfn)
+{
+ struct address_space *mapping = page_mapping(p);
+
+ SetPageError(p);
+ /* TBD: print more information about the file. */
+ if (mapping) {
+ /*
+ * IO error will be reported by write(), fsync(), etc.
+ * who check the mapping.
+ * This way the application knows that something went
+ * wrong with its dirty file data.
+ *
+ * There's one open issue:
+ *
+ * The EIO will be only reported on the next IO
+ * operation and then cleared through the IO map.
+ * Normally Linux has two mechanisms to pass IO error
+ * first through the AS_EIO flag in the address space
+ * and then through the PageError flag in the page.
+ * Since we drop pages on memory failure handling the
+ * only mechanism open to use is through AS_AIO.
+ *
+ * This has the disadvantage that it gets cleared on
+ * the first operation that returns an error, while
+ * the PageError bit is more sticky and only cleared
+ * when the page is reread or dropped. If an
+ * application assumes it will always get error on
+ * fsync, but does other operations on the fd before
+ * and the page is dropped inbetween then the error
+ * will not be properly reported.
+ *
+ * This can already happen even without hwpoisoned
+ * pages: first on metadata IO errors (which only
+ * report through AS_EIO) or when the page is dropped
+ * at the wrong time.
+ *
+ * So right now we assume that the application DTRT on
+ * the first EIO, but we're not worse than other parts
+ * of the kernel.
+ */
+ mapping_set_error(mapping, EIO);
+ }
+
+ return me_pagecache_clean(p, pfn);
+}
+
+/*
+ * Clean and dirty swap cache.
+ *
+ * Dirty swap cache page is tricky to handle. The page could live both in page
+ * cache and swap cache(ie. page is freshly swapped in). So it could be
+ * referenced concurrently by 2 types of PTEs:
+ * normal PTEs and swap PTEs. We try to handle them consistently by calling
+ * try_to_unmap(TTU_IGNORE_HWPOISON) to convert the normal PTEs to swap PTEs,
+ * and then
+ * - clear dirty bit to prevent IO
+ * - remove from LRU
+ * - but keep in the swap cache, so that when we return to it on
+ * a later page fault, we know the application is accessing
+ * corrupted data and shall be killed (we installed simple
+ * interception code in do_swap_page to catch it).
+ *
+ * Clean swap cache pages can be directly isolated. A later page fault will
+ * bring in the known good data from disk.
+ */
+static int me_swapcache_dirty(struct page *p, unsigned long pfn)
+{
+ int ret = FAILED;
+
+ ClearPageDirty(p);
+ /* Trigger EIO in shmem: */
+ ClearPageUptodate(p);
+
+ if (!isolate_lru_page(p)) {
+ page_cache_release(p);
+ ret = DELAYED;
+ }
+
+ return ret;
+}
+
+static int me_swapcache_clean(struct page *p, unsigned long pfn)
+{
+ int ret = FAILED;
+
+ if (!isolate_lru_page(p)) {
+ page_cache_release(p);
+ ret = RECOVERED;
+ }
+ delete_from_swap_cache(p);
+ return ret;
+}
+
+/*
+ * Huge pages. Needs work.
+ * Issues:
+ * No rmap support so we cannot find the original mapper. In theory could walk
+ * all MMs and look for the mappings, but that would be non atomic and racy.
+ * Need rmap for hugepages for this. Alternatively we could employ a heuristic,
+ * like just walking the current process and hoping it has it mapped (that
+ * should be usually true for the common "shared database cache" case)
+ * Should handle free huge pages and dequeue them too, but this needs to
+ * handle huge page accounting correctly.
+ */
+static int me_huge_page(struct page *p, unsigned long pfn)
+{
+ return FAILED;
+}
+
+/*
+ * Various page states we can handle.
+ *
+ * A page state is defined by its current page->flags bits.
+ * The table matches them in order and calls the right handler.
+ *
+ * This is quite tricky because we can access page at any time
+ * in its live cycle, so all accesses have to be extremly careful.
+ *
+ * This is not complete. More states could be added.
+ * For any missing state don't attempt recovery.
+ */
+
+#define dirty (1UL << PG_dirty)
+#define sc (1UL << PG_swapcache)
+#define unevict (1UL << PG_unevictable)
+#define mlock (1UL << PG_mlocked)
+#define writeback (1UL << PG_writeback)
+#define lru (1UL << PG_lru)
+#define swapbacked (1UL << PG_swapbacked)
+#define head (1UL << PG_head)
+#define tail (1UL << PG_tail)
+#define compound (1UL << PG_compound)
+#define slab (1UL << PG_slab)
+#define buddy (1UL << PG_buddy)
+#define reserved (1UL << PG_reserved)
+
+static struct page_state {
+ unsigned long mask;
+ unsigned long res;
+ char *msg;
+ int (*action)(struct page *p, unsigned long pfn);
+} error_states[] = {
+ { reserved, reserved, "reserved kernel", me_ignore },
+ { buddy, buddy, "free kernel", me_free },
+
+ /*
+ * Could in theory check if slab page is free or if we can drop
+ * currently unused objects without touching them. But just
+ * treat it as standard kernel for now.
+ */
+ { slab, slab, "kernel slab", me_kernel },
+
+#ifdef CONFIG_PAGEFLAGS_EXTENDED
+ { head, head, "huge", me_huge_page },
+ { tail, tail, "huge", me_huge_page },
+#else
+ { compound, compound, "huge", me_huge_page },
+#endif
+
+ { sc|dirty, sc|dirty, "swapcache", me_swapcache_dirty },
+ { sc|dirty, sc, "swapcache", me_swapcache_clean },
+
+ { unevict|dirty, unevict|dirty, "unevictable LRU", me_pagecache_dirty},
+ { unevict, unevict, "unevictable LRU", me_pagecache_clean},
+
+#ifdef CONFIG_HAVE_MLOCKED_PAGE_BIT
+ { mlock|dirty, mlock|dirty, "mlocked LRU", me_pagecache_dirty },
+ { mlock, mlock, "mlocked LRU", me_pagecache_clean },
+#endif
+
+ { lru|dirty, lru|dirty, "LRU", me_pagecache_dirty },
+ { lru|dirty, lru, "clean LRU", me_pagecache_clean },
+ { swapbacked, swapbacked, "anonymous", me_pagecache_clean },
+
+ /*
+ * Catchall entry: must be at end.
+ */
+ { 0, 0, "unknown page state", me_unknown },
+};
+
+#undef lru
+
+static void action_result(unsigned long pfn, char *msg, int result)
+{
+ struct page *page = NULL;
+ if (pfn_valid(pfn))
+ page = pfn_to_page(pfn);
+
+ printk(KERN_ERR "MCE %#lx: %s%s page recovery: %s\n",
+ pfn,
+ page && PageDirty(page) ? "dirty " : "",
+ msg, action_name[result]);
+}
+
+static int page_action(struct page_state *ps, struct page *p,
+ unsigned long pfn, int ref)
+{
+ int result;
+
+ result = ps->action(p, pfn);
+ action_result(pfn, ps->msg, result);
+ if (page_count(p) != 1 + ref)
+ printk(KERN_ERR
+ "MCE %#lx: %s page still referenced by %d users\n",
+ pfn, ps->msg, page_count(p) - 1);
+
+ /* Could do more checks here if page looks ok */
+ /*
+ * Could adjust zone counters here to correct for the missing page.
+ */
+
+ return result == RECOVERED ? 0 : -EBUSY;
+}
+
+#define N_UNMAP_TRIES 5
+
+/*
+ * Do all that is necessary to remove user space mappings. Unmap
+ * the pages and send SIGBUS to the processes if the data was dirty.
+ */
+static void hwpoison_user_mappings(struct page *p, unsigned long pfn,
+ int trapno)
+{
+ enum ttu_flags ttu = TTU_UNMAP | TTU_IGNORE_MLOCK | TTU_IGNORE_ACCESS;
+ struct address_space *mapping;
+ LIST_HEAD(tokill);
+ int ret;
+ int i;
+ int kill = 1;
+
+ if (PageReserved(p) || PageCompound(p) || PageSlab(p))
+ return;
+
+ if (!PageLRU(p))
+ lru_add_drain_all();
+
+ /*
+ * This check implies we don't kill processes if their pages
+ * are in the swap cache early. Those are always late kills.
+ */
+ if (!page_mapped(p))
+ return;
+
+ if (PageSwapCache(p)) {
+ printk(KERN_ERR
+ "MCE %#lx: keeping poisoned page in swap cache\n", pfn);
+ ttu |= TTU_IGNORE_HWPOISON;
+ }
+
+ /*
+ * Propagate the dirty bit from PTEs to struct page first, because we
+ * need this to decide if we should kill or just drop the page.
+ */
+ mapping = page_mapping(p);
+ if (!PageDirty(p) && mapping && mapping_cap_writeback_dirty(mapping)) {
+ if (page_mkclean(p)) {
+ SetPageDirty(p);
+ } else {
+ kill = 0;
+ ttu |= TTU_IGNORE_HWPOISON;
+ printk(KERN_INFO
+ "MCE %#lx: corrupted page was clean: dropped without side effects\n",
+ pfn);
+ }
+ }
+
+ /*
+ * First collect all the processes that have the page
+ * mapped in dirty form. This has to be done before try_to_unmap,
+ * because ttu takes the rmap data structures down.
+ *
+ * Error handling: We ignore errors here because
+ * there's nothing that can be done.
+ */
+ if (kill)
+ collect_procs(p, &tokill);
+
+ /*
+ * try_to_unmap can fail temporarily due to races.
+ * Try a few times (RED-PEN better strategy?)
+ */
+ for (i = 0; i < N_UNMAP_TRIES; i++) {
+ ret = try_to_unmap(p, ttu);
+ if (ret == SWAP_SUCCESS)
+ break;
+ pr_debug("MCE %#lx: try_to_unmap retry needed %d\n", pfn, ret);
+ }
+
+ if (ret != SWAP_SUCCESS)
+ printk(KERN_ERR "MCE %#lx: failed to unmap page (mapcount=%d)\n",
+ pfn, page_mapcount(p));
+
+ /*
+ * Now that the dirty bit has been propagated to the
+ * struct page and all unmaps done we can decide if
+ * killing is needed or not. Only kill when the page
+ * was dirty, otherwise the tokill list is merely
+ * freed. When there was a problem unmapping earlier
+ * use a more force-full uncatchable kill to prevent
+ * any accesses to the poisoned memory.
+ */
+ kill_procs_ao(&tokill, !!PageDirty(p), trapno,
+ ret != SWAP_SUCCESS, pfn);
+}
+
+int __memory_failure(unsigned long pfn, int trapno, int ref)
+{
+ struct page_state *ps;
+ struct page *p;
+ int res;
+
+ if (!sysctl_memory_failure_recovery)
+ panic("Memory failure from trap %d on page %lx", trapno, pfn);
+
+ if (!pfn_valid(pfn)) {
+ action_result(pfn, "memory outside kernel control", IGNORED);
+ return -EIO;
+ }
+
+ p = pfn_to_page(pfn);
+ if (TestSetPageHWPoison(p)) {
+ action_result(pfn, "already hardware poisoned", IGNORED);
+ return 0;
+ }
+
+ atomic_long_add(1, &mce_bad_pages);
+
+ /*
+ * We need/can do nothing about count=0 pages.
+ * 1) it's a free page, and therefore in safe hand:
+ * prep_new_page() will be the gate keeper.
+ * 2) it's part of a non-compound high order page.
+ * Implies some kernel user: cannot stop them from
+ * R/W the page; let's pray that the page has been
+ * used and will be freed some time later.
+ * In fact it's dangerous to directly bump up page count from 0,
+ * that may make page_freeze_refs()/page_unfreeze_refs() mismatch.
+ */
+ if (!get_page_unless_zero(compound_head(p))) {
+ action_result(pfn, "free or high order kernel", IGNORED);
+ return PageBuddy(compound_head(p)) ? 0 : -EBUSY;
+ }
+
+ /*
+ * Lock the page and wait for writeback to finish.
+ * It's very difficult to mess with pages currently under IO
+ * and in many cases impossible, so we just avoid it here.
+ */
+ lock_page_nosync(p);
+ wait_on_page_writeback(p);
+
+ /*
+ * Now take care of user space mappings.
+ */
+ hwpoison_user_mappings(p, pfn, trapno);
+
+ /*
+ * Torn down by someone else?
+ */
+ if (PageLRU(p) && !PageSwapCache(p) && p->mapping == NULL) {
+ action_result(pfn, "already truncated LRU", IGNORED);
+ res = 0;
+ goto out;
+ }
+
+ res = -EBUSY;
+ for (ps = error_states;; ps++) {
+ if ((p->flags & ps->mask) == ps->res) {
+ res = page_action(ps, p, pfn, ref);
+ break;
+ }
+ }
+out:
+ unlock_page(p);
+ return res;
+}
+EXPORT_SYMBOL_GPL(__memory_failure);
+
+/**
+ * memory_failure - Handle memory failure of a page.
+ * @pfn: Page Number of the corrupted page
+ * @trapno: Trap number reported in the signal to user space.
+ *
+ * This function is called by the low level machine check code
+ * of an architecture when it detects hardware memory corruption
+ * of a page. It tries its best to recover, which includes
+ * dropping pages, killing processes etc.
+ *
+ * The function is primarily of use for corruptions that
+ * happen outside the current execution context (e.g. when
+ * detected by a background scrubber)
+ *
+ * Must run in process context (e.g. a work queue) with interrupts
+ * enabled and no spinlocks hold.
+ */
+void memory_failure(unsigned long pfn, int trapno)
+{
+ __memory_failure(pfn, trapno, 0);
+}
unsigned long addr = vma->vm_start;
/*
- * Hide vma from rmap and vmtruncate before freeing pgtables
+ * Hide vma from rmap and truncate_pagecache before freeing
+ * pgtables
*/
anon_vma_unlink(vma);
unlink_file_vma(vma);
if (ret & VM_FAULT_ERROR) {
if (ret & VM_FAULT_OOM)
return i ? i : -ENOMEM;
- else if (ret & VM_FAULT_SIGBUS)
+ if (ret &
+ (VM_FAULT_HWPOISON|VM_FAULT_SIGBUS))
return i ? i : -EFAULT;
BUG();
}
* @mapping: the address space containing mmaps to be unmapped.
* @holebegin: byte in first page to unmap, relative to the start of
* the underlying file. This will be rounded down to a PAGE_SIZE
- * boundary. Note that this is different from vmtruncate(), which
+ * boundary. Note that this is different from truncate_pagecache(), which
* must keep the partial page. In contrast, we must get rid of
* partial pages.
* @holelen: size of prospective hole in bytes. This will be rounded
}
EXPORT_SYMBOL(unmap_mapping_range);
-/**
- * vmtruncate - unmap mappings "freed" by truncate() syscall
- * @inode: inode of the file used
- * @offset: file offset to start truncating
- *
- * NOTE! We have to be ready to update the memory sharing
- * between the file and the memory map for a potential last
- * incomplete page. Ugly, but necessary.
- */
-int vmtruncate(struct inode * inode, loff_t offset)
-{
- if (inode->i_size < offset) {
- unsigned long limit;
-
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && offset > limit)
- goto out_sig;
- if (offset > inode->i_sb->s_maxbytes)
- goto out_big;
- i_size_write(inode, offset);
- } else {
- struct address_space *mapping = inode->i_mapping;
-
- /*
- * truncation of in-use swapfiles is disallowed - it would
- * cause subsequent swapout to scribble on the now-freed
- * blocks.
- */
- if (IS_SWAPFILE(inode))
- return -ETXTBSY;
- i_size_write(inode, offset);
-
- /*
- * unmap_mapping_range is called twice, first simply for
- * efficiency so that truncate_inode_pages does fewer
- * single-page unmaps. However after this first call, and
- * before truncate_inode_pages finishes, it is possible for
- * private pages to be COWed, which remain after
- * truncate_inode_pages finishes, hence the second
- * unmap_mapping_range call must be made for correctness.
- */
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- truncate_inode_pages(mapping, offset);
- unmap_mapping_range(mapping, offset + PAGE_SIZE - 1, 0, 1);
- }
-
- if (inode->i_op->truncate)
- inode->i_op->truncate(inode);
- return 0;
-
-out_sig:
- send_sig(SIGXFSZ, current, 0);
-out_big:
- return -EFBIG;
-}
-EXPORT_SYMBOL(vmtruncate);
-
int vmtruncate_range(struct inode *inode, loff_t offset, loff_t end)
{
struct address_space *mapping = inode->i_mapping;
goto out;
entry = pte_to_swp_entry(orig_pte);
- if (is_migration_entry(entry)) {
- migration_entry_wait(mm, pmd, address);
+ if (unlikely(non_swap_entry(entry))) {
+ if (is_migration_entry(entry)) {
+ migration_entry_wait(mm, pmd, address);
+ } else if (is_hwpoison_entry(entry)) {
+ ret = VM_FAULT_HWPOISON;
+ } else {
+ print_bad_pte(vma, address, orig_pte, NULL);
+ ret = VM_FAULT_OOM;
+ }
goto out;
}
delayacct_set_flag(DELAYACCT_PF_SWAPIN);
/* Had to read the page from swap area: Major fault */
ret = VM_FAULT_MAJOR;
count_vm_event(PGMAJFAULT);
+ } else if (PageHWPoison(page)) {
+ ret = VM_FAULT_HWPOISON;
+ delayacct_clear_flag(DELAYACCT_PF_SWAPIN);
+ goto out;
}
lock_page(page);
if (unlikely(ret & (VM_FAULT_ERROR | VM_FAULT_NOPAGE)))
return ret;
+ if (unlikely(PageHWPoison(vmf.page))) {
+ if (ret & VM_FAULT_LOCKED)
+ unlock_page(vmf.page);
+ return VM_FAULT_HWPOISON;
+ }
+
/*
* For consistency in subsequent calls, make the faulted page always
* locked.
}
/* Establish migration ptes or remove ptes */
- try_to_unmap(page, 1);
+ try_to_unmap(page, TTU_MIGRATION|TTU_IGNORE_MLOCK|TTU_IGNORE_ACCESS);
skip_unmap:
if (!page_mapped(page))
{
}
-static struct vm_operations_struct special_mapping_vmops = {
+static const struct vm_operations_struct special_mapping_vmops = {
.close = special_mapping_close,
.fault = special_mapping_fault,
};
if (vma->vm_file) {
/*
* Subtle point from Rajesh Venkatasubramanian: before
- * moving file-based ptes, we must lock vmtruncate out,
- * since it might clean the dst vma before the src vma,
+ * moving file-based ptes, we must lock truncate_pagecache
+ * out, since it might clean the dst vma before the src vma,
* and we propagate stale pages into the dst afterward.
*/
mapping = vma->vm_file->f_mapping;
struct rb_root nommu_region_tree = RB_ROOT;
DECLARE_RWSEM(nommu_region_sem);
-struct vm_operations_struct generic_file_vm_ops = {
+const struct vm_operations_struct generic_file_vm_ops = {
};
-/*
- * Handle all mappings that got truncated by a "truncate()"
- * system call.
- *
- * NOTE! We have to be ready to update the memory sharing
- * between the file and the memory map for a potential last
- * incomplete page. Ugly, but necessary.
- */
-int vmtruncate(struct inode *inode, loff_t offset)
-{
- struct address_space *mapping = inode->i_mapping;
- unsigned long limit;
-
- if (inode->i_size < offset)
- goto do_expand;
- i_size_write(inode, offset);
-
- truncate_inode_pages(mapping, offset);
- goto out_truncate;
-
-do_expand:
- limit = current->signal->rlim[RLIMIT_FSIZE].rlim_cur;
- if (limit != RLIM_INFINITY && offset > limit)
- goto out_sig;
- if (offset > inode->i_sb->s_maxbytes)
- goto out;
- i_size_write(inode, offset);
-
-out_truncate:
- if (inode->i_op->truncate)
- inode->i_op->truncate(inode);
- return 0;
-out_sig:
- send_sig(SIGXFSZ, current, 0);
-out:
- return -EFBIG;
-}
-
-EXPORT_SYMBOL(vmtruncate);
-
/*
* Return the total memory allocated for this pointer, not
* just what the caller asked for.
int ret;
/* do the simple checks first */
- if (flags & MAP_FIXED || addr) {
+ if (flags & MAP_FIXED) {
printk(KERN_DEBUG
"%d: Can't do fixed-address/overlay mmap of RAM\n",
current->pid);
ret = vma->vm_file->f_op->mmap(vma->vm_file, vma);
if (ret == 0) {
vma->vm_region->vm_top = vma->vm_region->vm_end;
- return ret;
+ return 0;
}
if (ret != -ENOSYS)
return ret;
*/
static int do_mmap_private(struct vm_area_struct *vma,
struct vm_region *region,
- unsigned long len)
+ unsigned long len,
+ unsigned long capabilities)
{
struct page *pages;
unsigned long total, point, n, rlen;
* shared mappings on devices or memory
* - VM_MAYSHARE will be set if it may attempt to share
*/
- if (vma->vm_file) {
+ if (capabilities & BDI_CAP_MAP_DIRECT) {
ret = vma->vm_file->f_op->mmap(vma->vm_file, vma);
if (ret == 0) {
/* shouldn't return success if we're not sharing */
BUG_ON(!(vma->vm_flags & VM_MAYSHARE));
vma->vm_region->vm_top = vma->vm_region->vm_end;
- return ret;
+ return 0;
}
if (ret != -ENOSYS)
return ret;
kenter(",%lx,%lx,%lx,%lx,%lx", addr, len, prot, flags, pgoff);
- if (!(flags & MAP_FIXED))
- addr = round_hint_to_min(addr);
-
/* decide whether we should attempt the mapping, and if so what sort of
* mapping */
ret = validate_mmap_request(file, addr, len, prot, flags, pgoff,
return ret;
}
+ /* we ignore the address hint */
+ addr = 0;
+
/* we've determined that we can make the mapping, now translate what we
* now know into VMA flags */
vm_flags = determine_vm_flags(file, prot, flags, capabilities);
* - this is the hook for quasi-memory character devices to
* tell us the location of a shared mapping
*/
- if (file && file->f_op->get_unmapped_area) {
+ if (capabilities & BDI_CAP_MAP_DIRECT) {
addr = file->f_op->get_unmapped_area(file, addr, len,
pgoff, flags);
if (IS_ERR((void *) addr)) {
}
vma->vm_region = region;
- add_nommu_region(region);
- /* set up the mapping */
+ /* set up the mapping
+ * - the region is filled in if BDI_CAP_MAP_DIRECT is still set
+ */
if (file && vma->vm_flags & VM_SHARED)
ret = do_mmap_shared_file(vma);
else
- ret = do_mmap_private(vma, region, len);
+ ret = do_mmap_private(vma, region, len, capabilities);
if (ret < 0)
- goto error_put_region;
+ goto error_just_free;
+ add_nommu_region(region);
/* okay... we have a mapping; now we have to register it */
result = vma->vm_start;
kleave(" = %lx", result);
return result;
-error_put_region:
- __put_nommu_region(region);
- if (vma) {
- if (vma->vm_file) {
- fput(vma->vm_file);
- if (vma->vm_flags & VM_EXECUTABLE)
- removed_exe_file_vma(vma->vm_mm);
- }
- kmem_cache_free(vm_area_cachep, vma);
- }
- kleave(" = %d [pr]", ret);
- return ret;
-
error_just_free:
up_write(&nommu_region_sem);
error:
/*
* When balance_dirty_pages decides that the caller needs to perform some
* non-background writeback, this is how many pages it will attempt to write.
- * It should be somewhat larger than RATELIMIT_PAGES to ensure that reasonably
+ * It should be somewhat larger than dirtied pages to ensure that reasonably
* large amounts of I/O are submitted.
*/
-static inline long sync_writeback_pages(void)
+static inline long sync_writeback_pages(unsigned long dirtied)
{
- return ratelimit_pages + ratelimit_pages / 2;
+ if (dirtied < ratelimit_pages)
+ dirtied = ratelimit_pages;
+
+ return dirtied + dirtied / 2;
}
/* The following parameters are exported via /proc/sys/vm */
/*
- * Start background writeback (via pdflush) at this percentage
+ * Start background writeback (via writeback threads) at this percentage
*/
int dirty_background_ratio = 10;
}
int dirty_background_ratio_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int ret;
- ret = proc_dointvec_minmax(table, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
if (ret == 0 && write)
dirty_background_bytes = 0;
return ret;
}
int dirty_background_bytes_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int ret;
- ret = proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos);
+ ret = proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
if (ret == 0 && write)
dirty_background_ratio = 0;
return ret;
}
int dirty_ratio_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int old_ratio = vm_dirty_ratio;
int ret;
- ret = proc_dointvec_minmax(table, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
if (ret == 0 && write && vm_dirty_ratio != old_ratio) {
update_completion_period();
vm_dirty_bytes = 0;
int dirty_bytes_handler(struct ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
unsigned long old_bytes = vm_dirty_bytes;
int ret;
- ret = proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos);
+ ret = proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
if (ret == 0 && write && vm_dirty_bytes != old_bytes) {
update_completion_period();
vm_dirty_ratio = 0;
* balance_dirty_pages() must be called by processes which are generating dirty
* data. It looks at the number of dirty pages in the machine and will force
* the caller to perform writeback if the system is over `vm_dirty_ratio'.
- * If we're over `background_thresh' then pdflush is woken to perform some
- * writeout.
+ * If we're over `background_thresh' then the writeback threads are woken to
+ * perform some writeout.
*/
-static void balance_dirty_pages(struct address_space *mapping)
+static void balance_dirty_pages(struct address_space *mapping,
+ unsigned long write_chunk)
{
long nr_reclaimable, bdi_nr_reclaimable;
long nr_writeback, bdi_nr_writeback;
unsigned long dirty_thresh;
unsigned long bdi_thresh;
unsigned long pages_written = 0;
- unsigned long write_chunk = sync_writeback_pages();
unsigned long pause = 1;
struct backing_dev_info *bdi = mapping->backing_dev_info;
bdi->dirty_exceeded = 0;
if (writeback_in_progress(bdi))
- return; /* pdflush is already working this queue */
+ return;
/*
* In laptop mode, we wait until hitting the higher threshold before
* background_thresh, to keep the amount of dirty memory low.
*/
if ((laptop_mode && pages_written) ||
- (!laptop_mode && ((nr_writeback = global_page_state(NR_FILE_DIRTY)
- + global_page_state(NR_UNSTABLE_NFS))
+ (!laptop_mode && ((global_page_state(NR_FILE_DIRTY)
+ + global_page_state(NR_UNSTABLE_NFS))
> background_thresh)))
- bdi_start_writeback(bdi, nr_writeback);
+ bdi_start_writeback(bdi, NULL, 0);
}
void set_page_dirty_balance(struct page *page, int page_mkwrite)
p = &__get_cpu_var(bdp_ratelimits);
*p += nr_pages_dirtied;
if (unlikely(*p >= ratelimit)) {
+ ratelimit = sync_writeback_pages(*p);
*p = 0;
preempt_enable();
- balance_dirty_pages(mapping);
+ balance_dirty_pages(mapping, ratelimit);
return;
}
preempt_enable();
* sysctl handler for /proc/sys/vm/dirty_writeback_centisecs
*/
int dirty_writeback_centisecs_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
- proc_dointvec(table, write, file, buffer, length, ppos);
+ proc_dointvec(table, write, buffer, length, ppos);
return 0;
}
EXPORT_SYMBOL(redirty_page_for_writepage);
/*
+ * Dirty a page.
+ *
+ * For pages with a mapping this should be done under the page lock
+ * for the benefit of asynchronous memory errors who prefer a consistent
+ * dirty state. This rule can be broken in some special cases,
+ * but should be better not to.
+ *
* If the mapping doesn't provide a set_page_dirty a_op, then
* just fall through and assume that it wants buffer_heads.
*/
static unsigned long nr_shown;
static unsigned long nr_unshown;
+ /* Don't complain about poisoned pages */
+ if (PageHWPoison(page)) {
+ __ClearPageBuddy(page);
+ return;
+ }
+
/*
* Allow a burst of 60 reports, then keep quiet for that minute;
* or allow a steady drip of one report per second.
/*
* This page is about to be returned from the page allocator
*/
-static int prep_new_page(struct page *page, int order, gfp_t gfp_flags)
+static inline int check_new_page(struct page *page)
{
if (unlikely(page_mapcount(page) |
(page->mapping != NULL) |
bad_page(page);
return 1;
}
+ return 0;
+}
+
+static int prep_new_page(struct page *page, int order, gfp_t gfp_flags)
+{
+ int i;
+
+ for (i = 0; i < (1 << order); i++) {
+ struct page *p = page + i;
+ if (unlikely(check_new_page(p)))
+ return 1;
+ }
set_page_private(page, 0);
set_page_refcounted(page);
* sysctl handler for numa_zonelist_order
*/
int numa_zonelist_order_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length,
+ void __user *buffer, size_t *length,
loff_t *ppos)
{
char saved_string[NUMA_ZONELIST_ORDER_LEN];
if (write)
strncpy(saved_string, (char*)table->data,
NUMA_ZONELIST_ORDER_LEN);
- ret = proc_dostring(table, write, file, buffer, length, ppos);
+ ret = proc_dostring(table, write, buffer, length, ppos);
if (ret)
return ret;
if (write) {
* changes.
*/
int min_free_kbytes_sysctl_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
- proc_dointvec(table, write, file, buffer, length, ppos);
+ proc_dointvec(table, write, buffer, length, ppos);
if (write)
setup_per_zone_wmarks();
return 0;
#ifdef CONFIG_NUMA
int sysctl_min_unmapped_ratio_sysctl_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
struct zone *zone;
int rc;
- rc = proc_dointvec_minmax(table, write, file, buffer, length, ppos);
+ rc = proc_dointvec_minmax(table, write, buffer, length, ppos);
if (rc)
return rc;
}
int sysctl_min_slab_ratio_sysctl_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
struct zone *zone;
int rc;
- rc = proc_dointvec_minmax(table, write, file, buffer, length, ppos);
+ rc = proc_dointvec_minmax(table, write, buffer, length, ppos);
if (rc)
return rc;
* if in function of the boot time zone sizes.
*/
int lowmem_reserve_ratio_sysctl_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
- proc_dointvec_minmax(table, write, file, buffer, length, ppos);
+ proc_dointvec_minmax(table, write, buffer, length, ppos);
setup_per_zone_lowmem_reserve();
return 0;
}
*/
int percpu_pagelist_fraction_sysctl_handler(ctl_table *table, int write,
- struct file *file, void __user *buffer, size_t *length, loff_t *ppos)
+ void __user *buffer, size_t *length, loff_t *ppos)
{
struct zone *zone;
unsigned int cpu;
int ret;
- ret = proc_dointvec_minmax(table, write, file, buffer, length, ppos);
+ ret = proc_dointvec_minmax(table, write, buffer, length, ppos);
if (!write || (ret == -EINVAL))
return ret;
for_each_populated_zone(zone) {
*/
static void *pcpu_alloc(size_t size, size_t align, bool reserved)
{
+ static int warn_limit = 10;
struct pcpu_chunk *chunk;
+ const char *err;
int slot, off;
if (unlikely(!size || size > PCPU_MIN_UNIT_SIZE || align > PAGE_SIZE)) {
if (reserved && pcpu_reserved_chunk) {
chunk = pcpu_reserved_chunk;
if (size > chunk->contig_hint ||
- pcpu_extend_area_map(chunk) < 0)
+ pcpu_extend_area_map(chunk) < 0) {
+ err = "failed to extend area map of reserved chunk";
goto fail_unlock;
+ }
off = pcpu_alloc_area(chunk, size, align);
if (off >= 0)
goto area_found;
+ err = "alloc from reserved chunk failed";
goto fail_unlock;
}
case 1:
goto restart; /* pcpu_lock dropped, restart */
default:
+ err = "failed to extend area map";
goto fail_unlock;
}
spin_unlock_irq(&pcpu_lock);
chunk = alloc_pcpu_chunk();
- if (!chunk)
+ if (!chunk) {
+ err = "failed to allocate new chunk";
goto fail_unlock_mutex;
+ }
spin_lock_irq(&pcpu_lock);
pcpu_chunk_relocate(chunk, -1);
if (pcpu_populate_chunk(chunk, off, size)) {
spin_lock_irq(&pcpu_lock);
pcpu_free_area(chunk, off);
+ err = "failed to populate";
goto fail_unlock;
}
spin_unlock_irq(&pcpu_lock);
fail_unlock_mutex:
mutex_unlock(&pcpu_alloc_mutex);
+ if (warn_limit) {
+ pr_warning("PERCPU: allocation failed, size=%zu align=%zu, "
+ "%s\n", size, align, err);
+ dump_stack();
+ if (!--warn_limit)
+ pr_info("PERCPU: limit reached, disable warning\n");
+ }
return NULL;
}
struct pcpu_alloc_info *ai;
unsigned int *cpu_map;
+ /* this function may be called multiple times */
+ memset(group_map, 0, sizeof(group_map));
+ memset(group_cnt, 0, sizeof(group_map));
+
/*
* Determine min_unit_size, alloc_size and max_upa such that
* alloc_size is multiple of atom_size and is the smallest
int __init pcpu_setup_first_chunk(const struct pcpu_alloc_info *ai,
void *base_addr)
{
+ static char cpus_buf[4096] __initdata;
static int smap[2], dmap[2];
size_t dyn_size = ai->dyn_size;
size_t size_sum = ai->static_size + ai->reserved_size + dyn_size;
int *unit_map;
int group, unit, i;
+ cpumask_scnprintf(cpus_buf, sizeof(cpus_buf), cpu_possible_mask);
+
+#define PCPU_SETUP_BUG_ON(cond) do { \
+ if (unlikely(cond)) { \
+ pr_emerg("PERCPU: failed to initialize, %s", #cond); \
+ pr_emerg("PERCPU: cpu_possible_mask=%s\n", cpus_buf); \
+ pcpu_dump_alloc_info(KERN_EMERG, ai); \
+ BUG(); \
+ } \
+} while (0)
+
/* sanity checks */
BUILD_BUG_ON(ARRAY_SIZE(smap) >= PCPU_DFL_MAP_ALLOC ||
ARRAY_SIZE(dmap) >= PCPU_DFL_MAP_ALLOC);
- BUG_ON(ai->nr_groups <= 0);
- BUG_ON(!ai->static_size);
- BUG_ON(!base_addr);
- BUG_ON(ai->unit_size < size_sum);
- BUG_ON(ai->unit_size & ~PAGE_MASK);
- BUG_ON(ai->unit_size < PCPU_MIN_UNIT_SIZE);
-
- pcpu_dump_alloc_info(KERN_DEBUG, ai);
+ PCPU_SETUP_BUG_ON(ai->nr_groups <= 0);
+ PCPU_SETUP_BUG_ON(!ai->static_size);
+ PCPU_SETUP_BUG_ON(!base_addr);
+ PCPU_SETUP_BUG_ON(ai->unit_size < size_sum);
+ PCPU_SETUP_BUG_ON(ai->unit_size & ~PAGE_MASK);
+ PCPU_SETUP_BUG_ON(ai->unit_size < PCPU_MIN_UNIT_SIZE);
/* process group information and build config tables accordingly */
group_offsets = alloc_bootmem(ai->nr_groups * sizeof(group_offsets[0]));
unit_off = alloc_bootmem(nr_cpu_ids * sizeof(unit_off[0]));
for (cpu = 0; cpu < nr_cpu_ids; cpu++)
- unit_map[cpu] = NR_CPUS;
+ unit_map[cpu] = UINT_MAX;
pcpu_first_unit_cpu = NR_CPUS;
for (group = 0, unit = 0; group < ai->nr_groups; group++, unit += i) {
if (cpu == NR_CPUS)
continue;
- BUG_ON(cpu > nr_cpu_ids || !cpu_possible(cpu));
- BUG_ON(unit_map[cpu] != NR_CPUS);
+ PCPU_SETUP_BUG_ON(cpu > nr_cpu_ids);
+ PCPU_SETUP_BUG_ON(!cpu_possible(cpu));
+ PCPU_SETUP_BUG_ON(unit_map[cpu] != UINT_MAX);
unit_map[cpu] = unit + i;
unit_off[cpu] = gi->base_offset + i * ai->unit_size;
pcpu_nr_units = unit;
for_each_possible_cpu(cpu)
- BUG_ON(unit_map[cpu] == NR_CPUS);
+ PCPU_SETUP_BUG_ON(unit_map[cpu] == UINT_MAX);
+
+ /* we're done parsing the input, undefine BUG macro and dump config */
+#undef PCPU_SETUP_BUG_ON
+ pcpu_dump_alloc_info(KERN_INFO, ai);
pcpu_nr_groups = ai->nr_groups;
pcpu_group_offsets = group_offsets;
void *base = (void *)ULONG_MAX;
void **areas = NULL;
struct pcpu_alloc_info *ai;
- size_t size_sum, areas_size;
+ size_t size_sum, areas_size, max_distance;
int group, i, rc;
ai = pcpu_build_alloc_info(reserved_size, dyn_size, atom_size,
}
/* base address is now known, determine group base offsets */
- for (group = 0; group < ai->nr_groups; group++)
+ max_distance = 0;
+ for (group = 0; group < ai->nr_groups; group++) {
ai->groups[group].base_offset = areas[group] - base;
+ max_distance = max(max_distance, ai->groups[group].base_offset);
+ }
+ max_distance += ai->unit_size;
+
+ /* warn if maximum distance is further than 75% of vmalloc space */
+ if (max_distance > (VMALLOC_END - VMALLOC_START) * 3 / 4) {
+ pr_warning("PERCPU: max_distance=0x%lx too large for vmalloc "
+ "space 0x%lx\n",
+ max_distance, VMALLOC_END - VMALLOC_START);
+#ifdef CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK
+ /* and fail if we have fallback */
+ rc = -EINVAL;
+ goto out_free;
+#endif
+ }
pr_info("PERCPU: Embedded %zu pages/cpu @%p s%zu r%zu d%zu u%zu\n",
PFN_DOWN(size_sum), base, ai->static_size, ai->reserved_size,
* mapping->tree_lock (widely used, in set_page_dirty,
* in arch-dependent flush_dcache_mmap_lock,
* within inode_lock in __sync_single_inode)
+ *
+ * (code doesn't rely on that order so it could be switched around)
+ * ->tasklist_lock
+ * anon_vma->lock (memory_failure, collect_procs_anon)
+ * pte map lock
*/
#include <linux/mm.h>
* Getting a lock on a stable anon_vma from a page off the LRU is
* tricky: page_lock_anon_vma rely on RCU to guard against the races.
*/
-static struct anon_vma *page_lock_anon_vma(struct page *page)
+struct anon_vma *page_lock_anon_vma(struct page *page)
{
struct anon_vma *anon_vma;
unsigned long anon_mapping;
return NULL;
}
-static void page_unlock_anon_vma(struct anon_vma *anon_vma)
+void page_unlock_anon_vma(struct anon_vma *anon_vma)
{
spin_unlock(&anon_vma->lock);
rcu_read_unlock();
}
/*
- * At what user virtual address is page expected in vma? checking that the
- * page matches the vma: currently only used on anon pages, by unuse_vma;
+ * At what user virtual address is page expected in vma?
+ * checking that the page matches the vma.
*/
unsigned long page_address_in_vma(struct page *page, struct vm_area_struct *vma)
{
* if the page is not mapped into the page tables of this VMA. Only
* valid for normal file or anonymous VMAs.
*/
-static int page_mapped_in_vma(struct page *page, struct vm_area_struct *vma)
+int page_mapped_in_vma(struct page *page, struct vm_area_struct *vma)
{
unsigned long address;
pte_t *pte;
* repeatedly from either try_to_unmap_anon or try_to_unmap_file.
*/
static int try_to_unmap_one(struct page *page, struct vm_area_struct *vma,
- int migration)
+ enum ttu_flags flags)
{
struct mm_struct *mm = vma->vm_mm;
unsigned long address;
* If it's recently referenced (perhaps page_referenced
* skipped over this mm) then we should reactivate it.
*/
- if (!migration) {
+ if (!(flags & TTU_IGNORE_MLOCK)) {
if (vma->vm_flags & VM_LOCKED) {
ret = SWAP_MLOCK;
goto out_unmap;
}
+ }
+ if (!(flags & TTU_IGNORE_ACCESS)) {
if (ptep_clear_flush_young_notify(vma, address, pte)) {
ret = SWAP_FAIL;
goto out_unmap;
/* Update high watermark before we lower rss */
update_hiwater_rss(mm);
- if (PageAnon(page)) {
+ if (PageHWPoison(page) && !(flags & TTU_IGNORE_HWPOISON)) {
+ if (PageAnon(page))
+ dec_mm_counter(mm, anon_rss);
+ else
+ dec_mm_counter(mm, file_rss);
+ set_pte_at(mm, address, pte,
+ swp_entry_to_pte(make_hwpoison_entry(page)));
+ } else if (PageAnon(page)) {
swp_entry_t entry = { .val = page_private(page) };
if (PageSwapCache(page)) {
* pte. do_swap_page() will wait until the migration
* pte is removed and then restart fault handling.
*/
- BUG_ON(!migration);
+ BUG_ON(TTU_ACTION(flags) != TTU_MIGRATION);
entry = make_migration_entry(page, pte_write(pteval));
}
set_pte_at(mm, address, pte, swp_entry_to_pte(entry));
BUG_ON(pte_file(*pte));
- } else if (PAGE_MIGRATION && migration) {
+ } else if (PAGE_MIGRATION && (TTU_ACTION(flags) == TTU_MIGRATION)) {
/* Establish migration entry for a file page */
swp_entry_t entry;
entry = make_migration_entry(page, pte_write(pteval));
* vm_flags for that VMA. That should be OK, because that vma shouldn't be
* 'LOCKED.
*/
-static int try_to_unmap_anon(struct page *page, int unlock, int migration)
+static int try_to_unmap_anon(struct page *page, enum ttu_flags flags)
{
struct anon_vma *anon_vma;
struct vm_area_struct *vma;
unsigned int mlocked = 0;
int ret = SWAP_AGAIN;
+ int unlock = TTU_ACTION(flags) == TTU_MUNLOCK;
if (MLOCK_PAGES && unlikely(unlock))
ret = SWAP_SUCCESS; /* default for try_to_munlock() */
continue; /* must visit all unlocked vmas */
ret = SWAP_MLOCK; /* saw at least one mlocked vma */
} else {
- ret = try_to_unmap_one(page, vma, migration);
+ ret = try_to_unmap_one(page, vma, flags);
if (ret == SWAP_FAIL || !page_mapped(page))
break;
}
/**
* try_to_unmap_file - unmap/unlock file page using the object-based rmap method
* @page: the page to unmap/unlock
- * @unlock: request for unlock rather than unmap [unlikely]
- * @migration: unmapping for migration - ignored if @unlock
+ * @flags: action and flags
*
* Find all the mappings of a page using the mapping pointer and the vma chains
* contained in the address_space struct it points to.
* vm_flags for that VMA. That should be OK, because that vma shouldn't be
* 'LOCKED.
*/
-static int try_to_unmap_file(struct page *page, int unlock, int migration)
+static int try_to_unmap_file(struct page *page, enum ttu_flags flags)
{
struct address_space *mapping = page->mapping;
pgoff_t pgoff = page->index << (PAGE_CACHE_SHIFT - PAGE_SHIFT);
unsigned long max_nl_size = 0;
unsigned int mapcount;
unsigned int mlocked = 0;
+ int unlock = TTU_ACTION(flags) == TTU_MUNLOCK;
if (MLOCK_PAGES && unlikely(unlock))
ret = SWAP_SUCCESS; /* default for try_to_munlock() */
continue; /* must visit all vmas */
ret = SWAP_MLOCK;
} else {
- ret = try_to_unmap_one(page, vma, migration);
+ ret = try_to_unmap_one(page, vma, flags);
if (ret == SWAP_FAIL || !page_mapped(page))
goto out;
}
ret = SWAP_MLOCK; /* leave mlocked == 0 */
goto out; /* no need to look further */
}
- if (!MLOCK_PAGES && !migration && (vma->vm_flags & VM_LOCKED))
+ if (!MLOCK_PAGES && !(flags & TTU_IGNORE_MLOCK) &&
+ (vma->vm_flags & VM_LOCKED))
continue;
cursor = (unsigned long) vma->vm_private_data;
if (cursor > max_nl_cursor)
do {
list_for_each_entry(vma, &mapping->i_mmap_nonlinear,
shared.vm_set.list) {
- if (!MLOCK_PAGES && !migration &&
+ if (!MLOCK_PAGES && !(flags & TTU_IGNORE_MLOCK) &&
(vma->vm_flags & VM_LOCKED))
continue;
cursor = (unsigned long) vma->vm_private_data;
/**
* try_to_unmap - try to remove all page table mappings to a page
* @page: the page to get unmapped
- * @migration: migration flag
+ * @flags: action and flags
*
* Tries to remove all the page table entries which are mapping this
* page, used in the pageout path. Caller must hold the page lock.
* SWAP_FAIL - the page is unswappable
* SWAP_MLOCK - page is mlocked.
*/
-int try_to_unmap(struct page *page, int migration)
+int try_to_unmap(struct page *page, enum ttu_flags flags)
{
int ret;
BUG_ON(!PageLocked(page));
if (PageAnon(page))
- ret = try_to_unmap_anon(page, 0, migration);
+ ret = try_to_unmap_anon(page, flags);
else
- ret = try_to_unmap_file(page, 0, migration);
+ ret = try_to_unmap_file(page, flags);
if (ret != SWAP_MLOCK && !page_mapped(page))
ret = SWAP_SUCCESS;
return ret;
VM_BUG_ON(!PageLocked(page) || PageLRU(page));
if (PageAnon(page))
- return try_to_unmap_anon(page, 1, 0);
+ return try_to_unmap_anon(page, TTU_MUNLOCK);
else
- return try_to_unmap_file(page, 1, 0);
+ return try_to_unmap_file(page, TTU_MUNLOCK);
}
static const struct inode_operations shmem_inode_operations;
static const struct inode_operations shmem_dir_inode_operations;
static const struct inode_operations shmem_special_inode_operations;
-static struct vm_operations_struct shmem_vm_ops;
+static const struct vm_operations_struct shmem_vm_ops;
static struct backing_dev_info shmem_backing_dev_info __read_mostly = {
.ra_pages = 0, /* No readahead */
* sync from ever calling shmem_writepage; but a stacking filesystem
* may use the ->writepage of its underlying filesystem, in which case
* tmpfs should write out to swap only in response to memory pressure,
- * and not for pdflush or sync. However, in those cases, we do still
- * want to check if there's a redundant swappage to be discarded.
+ * and not for the writeback threads or sync. However, in those cases,
+ * we do still want to check if there's a redundant swappage to be
+ * discarded.
*/
if (wbc->for_reclaim)
swap = get_swap_page();
if (pos + copied > inode->i_size)
i_size_write(inode, pos + copied);
- unlock_page(page);
set_page_dirty(page);
+ unlock_page(page);
page_cache_release(page);
return copied;
iput(inode);
return error;
}
- unlock_page(page);
inode->i_mapping->a_ops = &shmem_aops;
inode->i_op = &shmem_symlink_inode_operations;
kaddr = kmap_atomic(page, KM_USER0);
memcpy(kaddr, symname, len);
kunmap_atomic(kaddr, KM_USER0);
set_page_dirty(page);
+ unlock_page(page);
page_cache_release(page);
}
if (dir->i_mode & S_ISGID)
.write_end = shmem_write_end,
#endif
.migratepage = migrate_page,
+ .error_remove_page = generic_error_remove_page,
};
static const struct file_operations shmem_file_operations = {
.put_super = shmem_put_super,
};
-static struct vm_operations_struct shmem_vm_ops = {
+static const struct vm_operations_struct shmem_vm_ops = {
.fault = shmem_fault,
#ifdef CONFIG_NUMA
.set_policy = shmem_set_policy,
struct swap_info_struct *p;
struct page *page = NULL;
- if (is_migration_entry(entry))
+ if (non_swap_entry(entry))
return 1;
p = swap_info_get(entry);
goto bad_swap;
}
- if (blk_queue_nonrot(bdev_get_queue(p->bdev))) {
- p->flags |= SWP_SOLIDSTATE;
- p->cluster_next = 1 + (random32() % p->highest_bit);
+ if (p->bdev) {
+ if (blk_queue_nonrot(bdev_get_queue(p->bdev))) {
+ p->flags |= SWP_SOLIDSTATE;
+ p->cluster_next = 1 + (random32() % p->highest_bit);
+ }
+ if (discard_swap(p) == 0)
+ p->flags |= SWP_DISCARDABLE;
}
- if (discard_swap(p) == 0)
- p->flags |= SWP_DISCARDABLE;
mutex_lock(&swapon_mutex);
spin_lock(&swap_lock);
int count;
bool has_cache;
- if (is_migration_entry(entry))
+ if (non_swap_entry(entry))
return -EINVAL;
type = swp_type(entry);
* its lock, b) when a concurrent invalidate_mapping_pages got there first and
* c) when tmpfs swizzles a page between a tmpfs inode and swapper_space.
*/
-static void
+static int
truncate_complete_page(struct address_space *mapping, struct page *page)
{
if (page->mapping != mapping)
- return;
+ return -EIO;
if (page_has_private(page))
do_invalidatepage(page, 0);
remove_from_page_cache(page);
ClearPageMappedToDisk(page);
page_cache_release(page); /* pagecache ref */
+ return 0;
}
/*
return ret;
}
+int truncate_inode_page(struct address_space *mapping, struct page *page)
+{
+ if (page_mapped(page)) {
+ unmap_mapping_range(mapping,
+ (loff_t)page->index << PAGE_CACHE_SHIFT,
+ PAGE_CACHE_SIZE, 0);
+ }
+ return truncate_complete_page(mapping, page);
+}
+
+/*
+ * Used to get rid of pages on hardware memory corruption.
+ */
+int generic_error_remove_page(struct address_space *mapping, struct page *page)
+{
+ if (!mapping)
+ return -EINVAL;
+ /*
+ * Only punch for normal data pages for now.
+ * Handling other types like directories would need more auditing.
+ */
+ if (!S_ISREG(mapping->host->i_mode))
+ return -EIO;
+ return truncate_inode_page(mapping, page);
+}
+EXPORT_SYMBOL(generic_error_remove_page);
+
+/*
+ * Safely invalidate one page from its pagecache mapping.
+ * It only drops clean, unused pages. The page must be locked.
+ *
+ * Returns 1 if the page is successfully invalidated, otherwise 0.
+ */
+int invalidate_inode_page(struct page *page)
+{
+ struct address_space *mapping = page_mapping(page);
+ if (!mapping)
+ return 0;
+ if (PageDirty(page) || PageWriteback(page))
+ return 0;
+ if (page_mapped(page))
+ return 0;
+ return invalidate_complete_page(mapping, page);
+}
+
/**
* truncate_inode_pages - truncate range of pages specified by start & end byte offsets
* @mapping: mapping to truncate
unlock_page(page);
continue;
}
- if (page_mapped(page)) {
- unmap_mapping_range(mapping,
- (loff_t)page_index<<PAGE_CACHE_SHIFT,
- PAGE_CACHE_SIZE, 0);
- }
- truncate_complete_page(mapping, page);
+ truncate_inode_page(mapping, page);
unlock_page(page);
}
pagevec_release(&pvec);
break;
lock_page(page);
wait_on_page_writeback(page);
- if (page_mapped(page)) {
- unmap_mapping_range(mapping,
- (loff_t)page->index<<PAGE_CACHE_SHIFT,
- PAGE_CACHE_SIZE, 0);
- }
+ truncate_inode_page(mapping, page);
if (page->index > next)
next = page->index;
next++;
- truncate_complete_page(mapping, page);
unlock_page(page);
}
pagevec_release(&pvec);
if (lock_failed)
continue;
- if (PageDirty(page) || PageWriteback(page))
- goto unlock;
- if (page_mapped(page))
- goto unlock;
- ret += invalidate_complete_page(mapping, page);
-unlock:
+ ret += invalidate_inode_page(page);
+
unlock_page(page);
if (next > end)
break;
return invalidate_inode_pages2_range(mapping, 0, -1);
}
EXPORT_SYMBOL_GPL(invalidate_inode_pages2);
+
+/**
+ * truncate_pagecache - unmap and remove pagecache that has been truncated
+ * @inode: inode
+ * @old: old file offset
+ * @new: new file offset
+ *
+ * inode's new i_size must already be written before truncate_pagecache
+ * is called.
+ *
+ * This function should typically be called before the filesystem
+ * releases resources associated with the freed range (eg. deallocates
+ * blocks). This way, pagecache will always stay logically coherent
+ * with on-disk format, and the filesystem would not have to deal with
+ * situations such as writepage being called for a page that has already
+ * had its underlying blocks deallocated.
+ */
+void truncate_pagecache(struct inode *inode, loff_t old, loff_t new)
+{
+ if (new < old) {
+ struct address_space *mapping = inode->i_mapping;
+
+ /*
+ * unmap_mapping_range is called twice, first simply for
+ * efficiency so that truncate_inode_pages does fewer
+ * single-page unmaps. However after this first call, and
+ * before truncate_inode_pages finishes, it is possible for
+ * private pages to be COWed, which remain after
+ * truncate_inode_pages finishes, hence the second
+ * unmap_mapping_range call must be made for correctness.
+ */
+ unmap_mapping_range(mapping, new + PAGE_SIZE - 1, 0, 1);
+ truncate_inode_pages(mapping, new);
+ unmap_mapping_range(mapping, new + PAGE_SIZE - 1, 0, 1);
+ }
+}
+EXPORT_SYMBOL(truncate_pagecache);
+
+/**
+ * vmtruncate - unmap mappings "freed" by truncate() syscall
+ * @inode: inode of the file used
+ * @offset: file offset to start truncating
+ *
+ * NOTE! We have to be ready to update the memory sharing
+ * between the file and the memory map for a potential last
+ * incomplete page. Ugly, but necessary.
+ */
+int vmtruncate(struct inode *inode, loff_t offset)
+{
+ loff_t oldsize;
+ int error;
+
+ error = inode_newsize_ok(inode, offset);
+ if (error)
+ return error;
+ oldsize = inode->i_size;
+ i_size_write(inode, offset);
+ truncate_pagecache(inode, oldsize, offset);
+ if (inode->i_op->truncate)
+ inode->i_op->truncate(inode);
+
+ return error;
+}
+EXPORT_SYMBOL(vmtruncate);
* processes. Try to unmap it here.
*/
if (page_mapped(page) && mapping) {
- switch (try_to_unmap(page, 0)) {
+ switch (try_to_unmap(page, TTU_UNMAP)) {
case SWAP_FAIL:
goto activate_locked;
case SWAP_AGAIN:
*
* If the caller is !__GFP_FS then the probability of a failure is reasonably
* high - the zone may be full of dirty or under-writeback pages, which this
- * caller can't do much about. We kick pdflush and take explicit naps in the
- * hope that some of these pages can be written. But if the allocating task
- * holds filesystem locks which prevent writeout this might not work, and the
- * allocation attempt will fail.
+ * caller can't do much about. We kick the writeback threads and take explicit
+ * naps in the hope that some of these pages can be written. But if the
+ * allocating task holds filesystem locks which prevent writeout this might not
+ * work, and the allocation attempt will fail.
*
* returns: 0, if no pages reclaimed
* else, the number of pages reclaimed
#ifdef CONFIG_CGROUP_MEM_RES_CTLR
+unsigned long mem_cgroup_shrink_node_zone(struct mem_cgroup *mem,
+ gfp_t gfp_mask, bool noswap,
+ unsigned int swappiness,
+ struct zone *zone, int nid)
+{
+ struct scan_control sc = {
+ .may_writepage = !laptop_mode,
+ .may_unmap = 1,
+ .may_swap = !noswap,
+ .swap_cluster_max = SWAP_CLUSTER_MAX,
+ .swappiness = swappiness,
+ .order = 0,
+ .mem_cgroup = mem,
+ .isolate_pages = mem_cgroup_isolate_pages,
+ };
+ nodemask_t nm = nodemask_of_node(nid);
+
+ sc.gfp_mask = (gfp_mask & GFP_RECLAIM_MASK) |
+ (GFP_HIGHUSER_MOVABLE & ~GFP_RECLAIM_MASK);
+ sc.nodemask = &nm;
+ sc.nr_reclaimed = 0;
+ sc.nr_scanned = 0;
+ /*
+ * NOTE: Although we can get the priority field, using it
+ * here is not a good idea, since it limits the pages we can scan.
+ * if we don't reclaim here, the shrink_zone from balance_pgdat
+ * will pick up pages from other mem cgroup's as well. We hack
+ * the priority and make it zero.
+ */
+ shrink_zone(0, zone, &sc);
+ return sc.nr_reclaimed;
+}
+
unsigned long try_to_free_mem_cgroup_pages(struct mem_cgroup *mem_cont,
gfp_t gfp_mask,
bool noswap,
unsigned int swappiness)
{
+ struct zonelist *zonelist;
struct scan_control sc = {
.may_writepage = !laptop_mode,
.may_unmap = 1,
.isolate_pages = mem_cgroup_isolate_pages,
.nodemask = NULL, /* we don't care the placement */
};
- struct zonelist *zonelist;
sc.gfp_mask = (gfp_mask & GFP_RECLAIM_MASK) |
(GFP_HIGHUSER_MOVABLE & ~GFP_RECLAIM_MASK);
for (i = 0; i <= end_zone; i++) {
struct zone *zone = pgdat->node_zones + i;
int nr_slab;
+ int nid, zid;
if (!populated_zone(zone))
continue;
temp_priority[i] = priority;
sc.nr_scanned = 0;
note_zone_scanning_priority(zone, priority);
+
+ nid = pgdat->node_id;
+ zid = zone_idx(zone);
+ /*
+ * Call soft limit reclaim before calling shrink_zone.
+ * For now we ignore the return value
+ */
+ mem_cgroup_soft_limit_reclaim(zone, order, sc.gfp_mask,
+ nid, zid);
/*
* We put equal pressure on every zone, unless one
* zone has way too many pages free already.
unsigned long scan_unevictable_pages;
int scan_unevictable_handler(struct ctl_table *table, int write,
- struct file *file, void __user *buffer,
+ void __user *buffer,
size_t *length, loff_t *ppos)
{
- proc_doulongvec_minmax(table, write, file, buffer, length, ppos);
+ proc_doulongvec_minmax(table, write, buffer, length, ppos);
if (write && *(unsigned long *)table->data)
scan_all_zones_unevictable_pages();
struct vlan_dev_info *vlan = vlan_dev_info(dev);
return nla_total_size(2) + /* IFLA_VLAN_ID */
+ sizeof(struct ifla_vlan_flags) + /* IFLA_VLAN_FLAGS */
vlan_qos_map_size(vlan->nr_ingress_mappings) +
vlan_qos_map_size(vlan->nr_egress_mappings);
}
}
int vcc_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct atm_vcc *vcc;
unsigned long value;
int vcc_ioctl(struct socket *sock, unsigned int cmd, unsigned long arg);
int vcc_compat_ioctl(struct socket *sock, unsigned int cmd, unsigned long arg);
int vcc_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
int vcc_getsockopt(struct socket *sock, int level, int optname,
char __user *optval, int __user *optlen);
}
static int pvc_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
int error;
static int svc_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct atm_vcc *vcc = ATM_SD(sock);
ax25_dev *ax25_dev;
ax25_cb *ax25;
unsigned int k;
+ int ret = 0;
if (copy_from_user(&ax25_ctl, arg, sizeof(ax25_ctl)))
return -EFAULT;
case AX25_WINDOW:
if (ax25->modulus == AX25_MODULUS) {
if (ax25_ctl.arg < 1 || ax25_ctl.arg > 7)
- return -EINVAL;
+ goto einval_put;
} else {
if (ax25_ctl.arg < 1 || ax25_ctl.arg > 63)
- return -EINVAL;
+ goto einval_put;
}
ax25->window = ax25_ctl.arg;
break;
case AX25_T1:
if (ax25_ctl.arg < 1)
- return -EINVAL;
+ goto einval_put;
ax25->rtt = (ax25_ctl.arg * HZ) / 2;
ax25->t1 = ax25_ctl.arg * HZ;
break;
case AX25_T2:
if (ax25_ctl.arg < 1)
- return -EINVAL;
+ goto einval_put;
ax25->t2 = ax25_ctl.arg * HZ;
break;
case AX25_N2:
if (ax25_ctl.arg < 1 || ax25_ctl.arg > 31)
- return -EINVAL;
+ goto einval_put;
ax25->n2count = 0;
ax25->n2 = ax25_ctl.arg;
break;
case AX25_T3:
if (ax25_ctl.arg < 0)
- return -EINVAL;
+ goto einval_put;
ax25->t3 = ax25_ctl.arg * HZ;
break;
case AX25_IDLE:
if (ax25_ctl.arg < 0)
- return -EINVAL;
+ goto einval_put;
ax25->idle = ax25_ctl.arg * 60 * HZ;
break;
case AX25_PACLEN:
if (ax25_ctl.arg < 16 || ax25_ctl.arg > 65535)
- return -EINVAL;
+ goto einval_put;
ax25->paclen = ax25_ctl.arg;
break;
default:
- return -EINVAL;
+ goto einval_put;
}
- return 0;
+out_put:
+ ax25_cb_put(ax25);
+ return ret;
+
+einval_put:
+ ret = -EINVAL;
+ goto out_put;
}
static void ax25_fillin_cb_from_dev(ax25_cb *ax25, ax25_dev *ax25_dev)
*/
static int ax25_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
ax25_cb *ax25;
case SO_BINDTODEVICE:
if (optlen > IFNAMSIZ)
- optlen=IFNAMSIZ;
- if (copy_from_user(devname, optval, optlen)) {
- res = -EFAULT;
- break;
- }
+ optlen = IFNAMSIZ;
- dev = dev_get_by_name(&init_net, devname);
- if (dev == NULL) {
- res = -ENODEV;
+ if (copy_from_user(devname, optval, optlen)) {
+ res = -EFAULT;
break;
}
(sock->state != SS_UNCONNECTED ||
sk->sk_state == TCP_LISTEN)) {
res = -EADDRNOTAVAIL;
- dev_put(dev);
+ break;
+ }
+
+ dev = dev_get_by_name(&init_net, devname);
+ if (!dev) {
+ res = -ENODEV;
break;
}
ax25->ax25_dev = ax25_dev_ax25dev(dev);
ax25_fillin_cb(ax25, ax25->ax25_dev);
+ dev_put(dev);
break;
default:
sock_init_data(NULL, sk);
- sk->sk_destruct = ax25_free_sock;
sk->sk_type = osk->sk_type;
sk->sk_priority = osk->sk_priority;
sk->sk_protocol = osk->sk_protocol;
}
sk->sk_protinfo = ax25;
+ sk->sk_destruct = ax25_free_sock;
ax25->sk = sk;
return sk;
ax25_info.idletimer = ax25_display_timer(&ax25->idletimer) / (60 * HZ);
ax25_info.n2count = ax25->n2count;
ax25_info.state = ax25->state;
- ax25_info.rcv_q = sk_wmem_alloc_get(sk);
- ax25_info.snd_q = sk_rmem_alloc_get(sk);
+ ax25_info.rcv_q = sk_rmem_alloc_get(sk);
+ ax25_info.snd_q = sk_wmem_alloc_get(sk);
ax25_info.vs = ax25->vs;
ax25_info.vr = ax25->vr;
ax25_info.va = ax25->va;
goto done;
}
-static int hci_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int len)
+static int hci_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int len)
{
struct hci_ufilter uf = { .opcode = 0 };
struct sock *sk = sock->sk;
return bt_sock_recvmsg(iocb, sock, msg, len, flags);
}
-static int l2cap_sock_setsockopt_old(struct socket *sock, int optname, char __user *optval, int optlen)
+static int l2cap_sock_setsockopt_old(struct socket *sock, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct l2cap_options opts;
return err;
}
-static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int optlen)
+static int l2cap_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct bt_security sec;
return copied ? : err;
}
-static int rfcomm_sock_setsockopt_old(struct socket *sock, int optname, char __user *optval, int optlen)
+static int rfcomm_sock_setsockopt_old(struct socket *sock, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
int err = 0;
return err;
}
-static int rfcomm_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int optlen)
+static int rfcomm_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct bt_security sec;
return err;
}
-static int sco_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int optlen)
+static int sco_sock_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
int err = 0;
br_fdb_delete_by_port(br, p, 1);
err1:
kobject_put(&p->kobj);
+ p = NULL; /* kobject_put frees */
err0:
dev_set_promiscuity(dev, -1);
put_back:
#ifdef CONFIG_SYSCTL
static
-int brnf_sysctl_call_tables(ctl_table * ctl, int write, struct file *filp,
+int brnf_sysctl_call_tables(ctl_table * ctl, int write,
void __user * buffer, size_t * lenp, loff_t * ppos)
{
int ret;
- ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
if (write && *(int *)(ctl->data))
*(int *)(ctl->data) = 1;
}
static int raw_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct raw_sock *ro = raw_sk(sk);
};
static int do_set_attach_filter(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct compat_sock_fprog __user *fprog32 = (struct compat_sock_fprog __user *)optval;
struct sock_fprog __user *kfprog = compat_alloc_user_space(sizeof(struct sock_fprog));
}
static int do_set_sock_timeout(struct socket *sock, int level,
- int optname, char __user *optval, int optlen)
+ int optname, char __user *optval, unsigned int optlen)
{
struct compat_timeval __user *up = (struct compat_timeval __user *) optval;
struct timeval ktime;
}
static int compat_sock_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (optname == SO_ATTACH_FILTER)
return do_set_attach_filter(sock, level, optname,
}
asmlinkage long compat_sys_setsockopt(int fd, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
int err;
struct socket *sock;
int compat_mc_setsockopt(struct sock *sock, int level, int optname,
- char __user *optval, int optlen,
- int (*setsockopt)(struct sock *,int,int,char __user *,int))
+ char __user *optval, unsigned int optlen,
+ int (*setsockopt)(struct sock *,int,int,char __user *,unsigned int))
{
char __user *koptval = optval;
int koptlen = optlen;
int ret = NET_RX_DROP;
__be16 type;
+ if (!skb->tstamp.tv64)
+ net_timestamp(skb);
+
if (skb->vlan_tci && vlan_hwaccel_do_receive(skb))
return NET_RX_SUCCESS;
if (netpoll_receive_skb(skb))
return NET_RX_DROP;
- if (!skb->tstamp.tv64)
- net_timestamp(skb);
-
if (!skb->iif)
skb->iif = skb->dev->ifindex;
#include <net/sock.h>
#include <linux/rtnetlink.h>
#include <linux/wireless.h>
-#include <net/iw_handler.h>
+#include <net/wext.h>
#include "net-sysfs.h"
char *))
{
struct net_device *dev = to_net_dev(d);
- const struct iw_statistics *iw = NULL;
+ const struct iw_statistics *iw;
ssize_t ret = -EINVAL;
read_lock(&dev_base_lock);
if (dev_isalive(dev)) {
- if (dev->wireless_handlers &&
- dev->wireless_handlers->get_wireless_stats)
- iw = dev->wireless_handlers->get_wireless_stats(dev);
- if (iw != NULL)
+ iw = get_wireless_stats(dev);
+ if (iw)
ret = (*format)(iw, buf);
}
read_unlock(&dev_base_lock);
*groups++ = &netstat_group;
#ifdef CONFIG_WIRELESS_EXT_SYSFS
- if (net->wireless_handlers && net->wireless_handlers->get_wireless_stats)
+ if (net->wireless_handlers || net->ieee80211_ptr)
*groups++ = &wireless_group;
#endif
#endif /* CONFIG_SYSFS */
#define F_QUEUE_MAP_CPU (1<<14) /* queue map mirrors smp_processor_id() */
/* Thread control flag bits */
-#define T_TERMINATE (1<<0)
-#define T_STOP (1<<1) /* Stop run */
-#define T_RUN (1<<2) /* Start run */
-#define T_REMDEVALL (1<<3) /* Remove all devs */
-#define T_REMDEV (1<<4) /* Remove one dev */
+#define T_STOP (1<<0) /* Stop run */
+#define T_RUN (1<<1) /* Start run */
+#define T_REMDEVALL (1<<2) /* Remove all devs */
+#define T_REMDEV (1<<3) /* Remove one dev */
/* If lock -- can be removed after some work */
#define if_lock(t) spin_lock(&(t->if_lock));
static void spin(struct pktgen_dev *pkt_dev, ktime_t spin_until)
{
- ktime_t start;
- s32 remaining;
+ ktime_t start_time, end_time;
+ s64 remaining;
struct hrtimer_sleeper t;
hrtimer_init_on_stack(&t.timer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
hrtimer_set_expires(&t.timer, spin_until);
remaining = ktime_to_us(hrtimer_expires_remaining(&t.timer));
- if (remaining <= 0)
+ if (remaining <= 0) {
+ pkt_dev->next_tx = ktime_add_ns(spin_until, pkt_dev->delay);
return;
+ }
- start = ktime_now();
+ start_time = ktime_now();
if (remaining < 100)
udelay(remaining); /* really small just spin */
else {
} while (t.task && pkt_dev->running && !signal_pending(current));
__set_current_state(TASK_RUNNING);
}
- pkt_dev->idle_acc += ktime_to_ns(ktime_sub(ktime_now(), start));
+ end_time = ktime_now();
+
+ pkt_dev->idle_acc += ktime_to_ns(ktime_sub(end_time, start_time));
+ pkt_dev->next_tx = ktime_add_ns(end_time, pkt_dev->delay);
}
static inline void set_pkt_overhead(struct pktgen_dev *pkt_dev)
mutex_unlock(&pktgen_thread_lock);
}
-static void idle(struct pktgen_dev *pkt_dev)
+static void pktgen_resched(struct pktgen_dev *pkt_dev)
{
ktime_t idle_start = ktime_now();
+ schedule();
+ pkt_dev->idle_acc += ktime_to_ns(ktime_sub(ktime_now(), idle_start));
+}
- if (need_resched())
- schedule();
- else
- cpu_relax();
+static void pktgen_wait_for_skb(struct pktgen_dev *pkt_dev)
+{
+ ktime_t idle_start = ktime_now();
+
+ while (atomic_read(&(pkt_dev->skb->users)) != 1) {
+ if (signal_pending(current))
+ break;
+ if (need_resched())
+ pktgen_resched(pkt_dev);
+ else
+ cpu_relax();
+ }
pkt_dev->idle_acc += ktime_to_ns(ktime_sub(ktime_now(), idle_start));
}
-
static void pktgen_xmit(struct pktgen_dev *pkt_dev)
{
struct net_device *odev = pkt_dev->odev;
u16 queue_map;
int ret;
- if (pkt_dev->delay) {
- spin(pkt_dev, pkt_dev->next_tx);
-
- /* This is max DELAY, this has special meaning of
- * "never transmit"
- */
- if (pkt_dev->delay == ULLONG_MAX) {
- pkt_dev->next_tx = ktime_add_ns(ktime_now(), ULONG_MAX);
- return;
- }
- }
-
- if (!pkt_dev->skb) {
- set_cur_queue_map(pkt_dev);
- queue_map = pkt_dev->cur_queue_map;
- } else {
- queue_map = skb_get_queue_mapping(pkt_dev->skb);
+ /* If device is offline, then don't send */
+ if (unlikely(!netif_running(odev) || !netif_carrier_ok(odev))) {
+ pktgen_stop_device(pkt_dev);
+ return;
}
- txq = netdev_get_tx_queue(odev, queue_map);
- /* Did we saturate the queue already? */
- if (netif_tx_queue_stopped(txq) || netif_tx_queue_frozen(txq)) {
- /* If device is down, then all queues are permnantly frozen */
- if (netif_running(odev))
- idle(pkt_dev);
- else
- pktgen_stop_device(pkt_dev);
+ /* This is max DELAY, this has special meaning of
+ * "never transmit"
+ */
+ if (unlikely(pkt_dev->delay == ULLONG_MAX)) {
+ pkt_dev->next_tx = ktime_add_ns(ktime_now(), ULONG_MAX);
return;
}
+ /* If no skb or clone count exhausted then get new one */
if (!pkt_dev->skb || (pkt_dev->last_ok &&
++pkt_dev->clone_count >= pkt_dev->clone_skb)) {
/* build a new pkt */
pkt_dev->clone_count = 0; /* reset counter */
}
- /* fill_packet() might have changed the queue */
+ if (pkt_dev->delay && pkt_dev->last_ok)
+ spin(pkt_dev, pkt_dev->next_tx);
+
queue_map = skb_get_queue_mapping(pkt_dev->skb);
txq = netdev_get_tx_queue(odev, queue_map);
__netif_tx_lock_bh(txq);
- if (unlikely(netif_tx_queue_stopped(txq) || netif_tx_queue_frozen(txq)))
- pkt_dev->last_ok = 0;
- else {
- atomic_inc(&(pkt_dev->skb->users));
+ atomic_inc(&(pkt_dev->skb->users));
- retry_now:
+ if (unlikely(netif_tx_queue_stopped(txq) || netif_tx_queue_frozen(txq)))
+ ret = NETDEV_TX_BUSY;
+ else
ret = (*xmit)(pkt_dev->skb, odev);
- switch (ret) {
- case NETDEV_TX_OK:
- txq_trans_update(txq);
- pkt_dev->last_ok = 1;
- pkt_dev->sofar++;
- pkt_dev->seq_num++;
- pkt_dev->tx_bytes += pkt_dev->cur_pkt_size;
- break;
- case NETDEV_TX_LOCKED:
- cpu_relax();
- goto retry_now;
- default: /* Drivers are not supposed to return other values! */
- if (net_ratelimit())
- pr_info("pktgen: %s xmit error: %d\n",
- odev->name, ret);
- pkt_dev->errors++;
- /* fallthru */
- case NETDEV_TX_BUSY:
- /* Retry it next time */
- atomic_dec(&(pkt_dev->skb->users));
- pkt_dev->last_ok = 0;
- }
-
- if (pkt_dev->delay)
- pkt_dev->next_tx = ktime_add_ns(ktime_now(),
- pkt_dev->delay);
+
+ switch (ret) {
+ case NETDEV_TX_OK:
+ txq_trans_update(txq);
+ pkt_dev->last_ok = 1;
+ pkt_dev->sofar++;
+ pkt_dev->seq_num++;
+ pkt_dev->tx_bytes += pkt_dev->cur_pkt_size;
+ break;
+ default: /* Drivers are not supposed to return other values! */
+ if (net_ratelimit())
+ pr_info("pktgen: %s xmit error: %d\n",
+ odev->name, ret);
+ pkt_dev->errors++;
+ /* fallthru */
+ case NETDEV_TX_LOCKED:
+ case NETDEV_TX_BUSY:
+ /* Retry it next time */
+ atomic_dec(&(pkt_dev->skb->users));
+ pkt_dev->last_ok = 0;
}
__netif_tx_unlock_bh(txq);
/* If pkt_dev->count is zero, then run forever */
if ((pkt_dev->count != 0) && (pkt_dev->sofar >= pkt_dev->count)) {
- while (atomic_read(&(pkt_dev->skb->users)) != 1) {
- if (signal_pending(current))
- break;
- idle(pkt_dev);
- }
+ pktgen_wait_for_skb(pkt_dev);
/* Done with this */
pktgen_stop_device(pkt_dev);
while (!kthread_should_stop()) {
pkt_dev = next_to_run(t);
- if (!pkt_dev &&
- (t->control & (T_STOP | T_RUN | T_REMDEVALL | T_REMDEV))
- == 0) {
- prepare_to_wait(&(t->queue), &wait,
- TASK_INTERRUPTIBLE);
- schedule_timeout(HZ / 10);
- finish_wait(&(t->queue), &wait);
+ if (unlikely(!pkt_dev && t->control == 0)) {
+ wait_event_interruptible_timeout(t->queue,
+ t->control != 0,
+ HZ/10);
+ continue;
}
__set_current_state(TASK_RUNNING);
- if (pkt_dev)
+ if (likely(pkt_dev)) {
pktgen_xmit(pkt_dev);
+ if (need_resched())
+ pktgen_resched(pkt_dev);
+ else
+ cpu_relax();
+ }
+
if (t->control & T_STOP) {
pktgen_stop(t);
t->control &= ~(T_STOP);
*/
int sock_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
int val;
void sock_wfree(struct sk_buff *skb)
{
struct sock *sk = skb->sk;
- int res;
+ unsigned int len = skb->truesize;
- /* In case it might be waiting for more memory. */
- res = atomic_sub_return(skb->truesize, &sk->sk_wmem_alloc);
- if (!sock_flag(sk, SOCK_USE_WRITE_QUEUE))
+ if (!sock_flag(sk, SOCK_USE_WRITE_QUEUE)) {
+ /*
+ * Keep a reference on sk_wmem_alloc, this will be released
+ * after sk_write_space() call
+ */
+ atomic_sub(len - 1, &sk->sk_wmem_alloc);
sk->sk_write_space(sk);
+ len = 1;
+ }
/*
- * if sk_wmem_alloc reached 0, we are last user and should
- * free this sock, as sk_free() call could not do it.
+ * if sk_wmem_alloc reaches 0, we must finish what sk_free()
+ * could not do because of in-flight packets
*/
- if (res == 0)
+ if (atomic_sub_and_test(len, &sk->sk_wmem_alloc))
__sk_free(sk);
}
EXPORT_SYMBOL(sock_wfree);
EXPORT_SYMBOL(sock_no_shutdown);
int sock_no_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
return -EOPNOTSUPP;
}
* Set socket options on an inet socket.
*/
int sock_common_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
#ifdef CONFIG_COMPAT
int compat_sock_common_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
nlmsg_end(dcbnl_skb, nlh);
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret)
- goto err;
+ return -EINVAL;
return 0;
nlmsg_failure:
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret)
- goto err;
+ goto err_out;
return 0;
nlmsg_failure:
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret)
- goto err;
+ goto err_out;
return 0;
nlmsg_failure:
-err:
kfree_skb(dcbnl_skb);
err_out:
return -EINVAL;
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret)
- goto err;
+ goto err_out;
return 0;
nlmsg_failure:
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret) {
ret = -EINVAL;
- goto err;
+ goto err_out;
}
return 0;
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret)
- goto err;
+ goto err_out;
return 0;
ret = rtnl_unicast(dcbnl_skb, &init_net, pid);
if (ret)
- goto err;
+ goto err_out;
return 0;
extern int dccp_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
extern int dccp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
#ifdef CONFIG_COMPAT
extern int compat_dccp_getsockopt(struct sock *sk,
int level, int optname,
char __user *optval, int __user *optlen);
extern int compat_dccp_setsockopt(struct sock *sk,
int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
#endif
extern int dccp_ioctl(struct sock *sk, int cmd, unsigned long arg);
extern int dccp_sendmsg(struct kiocb *iocb, struct sock *sk,
EXPORT_SYMBOL_GPL(dccp_ioctl);
static int dccp_setsockopt_service(struct sock *sk, const __be32 service,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct dccp_sock *dp = dccp_sk(sk);
struct dccp_service_list *sl = NULL;
}
static int dccp_setsockopt_ccid(struct sock *sk, int type,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
u8 *val;
int rc = 0;
}
static int do_dccp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct dccp_sock *dp = dccp_sk(sk);
int val, err = 0;
}
int dccp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level != SOL_DCCP)
return inet_csk(sk)->icsk_af_ops->setsockopt(sk, level,
#ifdef CONFIG_COMPAT
int compat_dccp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level != SOL_DCCP)
return inet_csk_compat_setsockopt(sk, level, optname,
static struct hlist_head dn_wild_sk;
static atomic_t decnet_memory_allocated;
-static int __dn_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int optlen, int flags);
+static int __dn_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int optlen, int flags);
static int __dn_getsockopt(struct socket *sock, int level, int optname, char __user *optval, int __user *optlen, int flags);
static struct hlist_head *dn_find_list(struct sock *sk)
return err;
}
-static int dn_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int optlen)
+static int dn_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
int err;
return err;
}
-static int __dn_setsockopt(struct socket *sock, int level,int optname, char __user *optval, int optlen, int flags)
+static int __dn_setsockopt(struct socket *sock, int level,int optname, char __user *optval, unsigned int optlen, int flags)
{
struct sock *sk = sock->sk;
struct dn_scp *scp = DN_SK(sk);
static int min_priority[1];
static int max_priority[] = { 127 }; /* From DECnet spec */
-static int dn_forwarding_proc(ctl_table *, int, struct file *,
+static int dn_forwarding_proc(ctl_table *, int,
void __user *, size_t *, loff_t *);
static int dn_forwarding_sysctl(ctl_table *table,
void __user *oldval, size_t __user *oldlenp,
}
static int dn_forwarding_proc(ctl_table *table, int write,
- struct file *filep,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
dn_db = dev->dn_ptr;
old = dn_db->parms.forwarding;
- err = proc_dointvec(table, write, filep, buffer, lenp, ppos);
+ err = proc_dointvec(table, write, buffer, lenp, ppos);
if ((err >= 0) && write) {
if (dn_db->parms.forwarding < 0)
}
static int dn_node_address_handler(ctl_table *table, int write,
- struct file *filp,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
static int dn_def_dev_handler(ctl_table *table, int write,
- struct file * filp,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
}
static int dgram_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct dgram_sock *ro = dgram_sk(sk);
int val;
}
static int raw_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
return -EOPNOTSUPP;
}
{
struct flowi fl = {
.oif = sk->sk_bound_dev_if,
+ .mark = sk->sk_mark,
.nl_u = {
.ip4_u = {
.daddr = daddr,
}
static int devinet_conf_proc(ctl_table *ctl, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
- int ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
if (write) {
struct ipv4_devconf *cnf = ctl->extra1;
}
static int devinet_sysctl_forward(ctl_table *ctl, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
int *valp = ctl->data;
int val = *valp;
- int ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
if (write && *valp != val) {
struct net *net = ctl->extra2;
}
int ipv4_doint_and_flush(ctl_table *ctl, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
int *valp = ctl->data;
int val = *valp;
- int ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
struct net *net = ctl->extra2;
if (write && *valp != val)
EXPORT_SYMBOL_GPL(inet_csk_compat_getsockopt);
int inet_csk_compat_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
const struct inet_connection_sock *icsk = inet_csk(sk);
solution, but it supposes maintaing new variable in ALL
skb, even if no tunneling is used.
- Current solution: t->recursion lock breaks dead loops. It looks
- like dev->tbusy flag, but I preferred new variable, because
- the semantics is different. One day, when hard_start_xmit
- will be multithreaded we will have to use skb->encapsulation.
+ Current solution: HARD_TX_LOCK lock breaks dead loops.
__be32 dst;
int mtu;
- if (tunnel->recursion++) {
- stats->collisions++;
- goto tx_error;
- }
-
if (dev->type == ARPHRD_ETHER)
IPCB(skb)->flags = 0;
ip_rt_put(rt);
stats->tx_dropped++;
dev_kfree_skb(skb);
- tunnel->recursion--;
return NETDEV_TX_OK;
}
if (skb->sk)
nf_reset(skb);
IPTUNNEL_XMIT();
- tunnel->recursion--;
return NETDEV_TX_OK;
tx_error_icmp:
tx_error:
stats->tx_errors++;
dev_kfree_skb(skb);
- tunnel->recursion--;
return NETDEV_TX_OK;
}
{
struct flowi fl = { .oif = sk->sk_bound_dev_if,
+ .mark = sk->sk_mark,
.nl_u = { .ip4_u =
{ .daddr = daddr,
.saddr = inet->saddr,
*/
static int do_ip_setsockopt(struct sock *sk, int level,
- int optname, char __user *optval, int optlen)
+ int optname, char __user *optval, unsigned int optlen)
{
struct inet_sock *inet = inet_sk(sk);
int val = 0, err;
* Check the arguments are allowable
*/
+ if (optlen < sizeof(struct in_addr))
+ goto e_inval;
+
err = -EFAULT;
if (optlen >= sizeof(struct ip_mreqn)) {
if (copy_from_user(&mreq, optval, sizeof(mreq)))
}
int ip_setsockopt(struct sock *sk, int level,
- int optname, char __user *optval, int optlen)
+ int optname, char __user *optval, unsigned int optlen)
{
int err;
#ifdef CONFIG_COMPAT
int compat_ip_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
int err;
__be32 dst = tiph->daddr;
int mtu;
- if (tunnel->recursion++) {
- stats->collisions++;
- goto tx_error;
- }
-
if (skb->protocol != htons(ETH_P_IP))
goto tx_error;
ip_rt_put(rt);
stats->tx_dropped++;
dev_kfree_skb(skb);
- tunnel->recursion--;
return NETDEV_TX_OK;
}
if (skb->sk)
nf_reset(skb);
IPTUNNEL_XMIT();
- tunnel->recursion--;
return NETDEV_TX_OK;
tx_error_icmp:
tx_error:
stats->tx_errors++;
dev_kfree_skb(skb);
- tunnel->recursion--;
return NETDEV_TX_OK;
}
* MOSPF/PIM router set up we can clean this up.
*/
-int ip_mroute_setsockopt(struct sock *sk, int optname, char __user *optval, int optlen)
+int ip_mroute_setsockopt(struct sock *sk, int optname, char __user *optval, unsigned int optlen)
{
int ret;
struct vifctl vif;
}
static int do_raw_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (optname == ICMP_FILTER) {
if (inet_sk(sk)->num != IPPROTO_ICMP)
}
static int raw_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level != SOL_RAW)
return ip_setsockopt(sk, level, optname, optval, optlen);
#ifdef CONFIG_COMPAT
static int compat_raw_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level != SOL_RAW)
return compat_ip_setsockopt(sk, level, optname, optval, optlen);
#ifdef CONFIG_SYSCTL
static int ipv4_sysctl_rtcache_flush(ctl_table *__ctl, int write,
- struct file *filp, void __user *buffer,
+ void __user *buffer,
size_t *lenp, loff_t *ppos)
{
if (write) {
memcpy(&ctl, __ctl, sizeof(ctl));
ctl.data = &flush_delay;
- proc_dointvec(&ctl, write, filp, buffer, lenp, ppos);
+ proc_dointvec(&ctl, write, buffer, lenp, ppos);
net = (struct net *)__ctl->extra1;
rt_cache_flush(net, flush_delay);
}
static int ipv4_sysctl_rt_secret_interval(ctl_table *ctl, int write,
- struct file *filp,
void __user *buffer, size_t *lenp,
loff_t *ppos)
{
int old = ip_rt_secret_interval;
- int ret = proc_dointvec_jiffies(ctl, write, filp, buffer, lenp, ppos);
+ int ret = proc_dointvec_jiffies(ctl, write, buffer, lenp, ppos);
rt_secret_reschedule(old);
}
/* Validate changes from /proc interface. */
-static int ipv4_local_port_range(ctl_table *table, int write, struct file *filp,
+static int ipv4_local_port_range(ctl_table *table, int write,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
};
inet_get_local_port_range(range, range + 1);
- ret = proc_dointvec_minmax(&tmp, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec_minmax(&tmp, write, buffer, lenp, ppos);
if (write && ret == 0) {
if (range[1] < range[0])
}
-static int proc_tcp_congestion_control(ctl_table *ctl, int write, struct file * filp,
+static int proc_tcp_congestion_control(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
char val[TCP_CA_NAME_MAX];
tcp_get_default_congestion_control(val);
- ret = proc_dostring(&tbl, write, filp, buffer, lenp, ppos);
+ ret = proc_dostring(&tbl, write, buffer, lenp, ppos);
if (write && ret == 0)
ret = tcp_set_default_congestion_control(val);
return ret;
}
static int proc_tcp_available_congestion_control(ctl_table *ctl,
- int write, struct file * filp,
+ int write,
void __user *buffer, size_t *lenp,
loff_t *ppos)
{
if (!tbl.data)
return -ENOMEM;
tcp_get_available_congestion_control(tbl.data, TCP_CA_BUF_MAX);
- ret = proc_dostring(&tbl, write, filp, buffer, lenp, ppos);
+ ret = proc_dostring(&tbl, write, buffer, lenp, ppos);
kfree(tbl.data);
return ret;
}
static int proc_allowed_congestion_control(ctl_table *ctl,
- int write, struct file * filp,
+ int write,
void __user *buffer, size_t *lenp,
loff_t *ppos)
{
return -ENOMEM;
tcp_get_allowed_congestion_control(tbl.data, tbl.maxlen);
- ret = proc_dostring(&tbl, write, filp, buffer, lenp, ppos);
+ ret = proc_dostring(&tbl, write, buffer, lenp, ppos);
if (write && ret == 0)
ret = tcp_set_allowed_congestion_control(tbl.data);
kfree(tbl.data);
lock_sock(sk);
- timeo = sock_rcvtimeo(sk, flags & SPLICE_F_NONBLOCK);
+ timeo = sock_rcvtimeo(sk, sock->file->f_flags & O_NONBLOCK);
while (tss.len) {
ret = __tcp_splice_read(sk, &tss);
if (ret < 0)
* Socket option code for TCP.
*/
static int do_tcp_setsockopt(struct sock *sk, int level,
- int optname, char __user *optval, int optlen)
+ int optname, char __user *optval, unsigned int optlen)
{
struct tcp_sock *tp = tcp_sk(sk);
struct inet_connection_sock *icsk = inet_csk(sk);
return -EINVAL;
val = strncpy_from_user(name, optval,
- min(TCP_CA_NAME_MAX-1, optlen));
+ min_t(long, TCP_CA_NAME_MAX-1, optlen));
if (val < 0)
return -EFAULT;
name[val] = 0;
}
int tcp_setsockopt(struct sock *sk, int level, int optname, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct inet_connection_sock *icsk = inet_csk(sk);
#ifdef CONFIG_COMPAT
int compat_tcp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level != SOL_TCP)
return inet_csk_compat_setsockopt(sk, level, optname,
#define OPTION_SACK_ADVERTISE (1 << 0)
#define OPTION_TS (1 << 1)
#define OPTION_MD5 (1 << 2)
+#define OPTION_WSCALE (1 << 3)
struct tcp_out_options {
u8 options; /* bit field of OPTION_* */
TCPOLEN_SACK_PERM);
}
- if (unlikely(opts->ws)) {
+ if (unlikely(OPTION_WSCALE & opts->options)) {
*ptr++ = htonl((TCPOPT_NOP << 24) |
(TCPOPT_WINDOW << 16) |
(TCPOLEN_WINDOW << 8) |
}
if (likely(sysctl_tcp_window_scaling)) {
opts->ws = tp->rx_opt.rcv_wscale;
- if (likely(opts->ws))
- size += TCPOLEN_WSCALE_ALIGNED;
+ opts->options |= OPTION_WSCALE;
+ size += TCPOLEN_WSCALE_ALIGNED;
}
if (likely(sysctl_tcp_sack)) {
opts->options |= OPTION_SACK_ADVERTISE;
if (likely(ireq->wscale_ok)) {
opts->ws = ireq->rcv_wscale;
- if (likely(opts->ws))
- size += TCPOLEN_WSCALE_ALIGNED;
+ opts->options |= OPTION_WSCALE;
+ size += TCPOLEN_WSCALE_ALIGNED;
}
if (likely(doing_ts)) {
opts->options |= OPTION_TS;
if (rt == NULL) {
struct flowi fl = { .oif = ipc.oif,
+ .mark = sk->sk_mark,
.nl_u = { .ip4_u =
{ .daddr = faddr,
.saddr = saddr,
* Socket option code for UDP
*/
int udp_lib_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen,
+ char __user *optval, unsigned int optlen,
int (*push_pending_frames)(struct sock *))
{
struct udp_sock *up = udp_sk(sk);
EXPORT_SYMBOL(udp_lib_setsockopt);
int udp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level == SOL_UDP || level == SOL_UDPLITE)
return udp_lib_setsockopt(sk, level, optname, optval, optlen,
#ifdef CONFIG_COMPAT
int compat_udp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level == SOL_UDP || level == SOL_UDPLITE)
return udp_lib_setsockopt(sk, level, optname, optval, optlen,
extern int udp_v4_get_port(struct sock *sk, unsigned short snum);
extern int udp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
extern int udp_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
#ifdef CONFIG_COMPAT
extern int compat_udp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
extern int compat_udp_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
#endif
#ifdef CONFIG_SYSCTL
static
-int addrconf_sysctl_forward(ctl_table *ctl, int write, struct file * filp,
+int addrconf_sysctl_forward(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int *valp = ctl->data;
int val = *valp;
int ret;
- ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
if (write)
ret = addrconf_fixup_forwarding(ctl, valp, val);
}
static
-int addrconf_sysctl_disable(ctl_table *ctl, int write, struct file * filp,
+int addrconf_sysctl_disable(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int *valp = ctl->data;
int val = *valp;
int ret;
- ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
if (write)
ret = addrconf_disable_ipv6(ctl, valp, val);
struct net_device_stats *stats = &t->dev->stats;
int ret;
- if (t->recursion++) {
- stats->collisions++;
- goto tx_err;
- }
-
switch (skb->protocol) {
case htons(ETH_P_IP):
ret = ip4ip6_tnl_xmit(skb, dev);
if (ret < 0)
goto tx_err;
- t->recursion--;
return NETDEV_TX_OK;
tx_err:
stats->tx_errors++;
stats->tx_dropped++;
kfree_skb(skb);
- t->recursion--;
return NETDEV_TX_OK;
}
* MOSPF/PIM router set up we can clean this up.
*/
-int ip6_mroute_setsockopt(struct sock *sk, int optname, char __user *optval, int optlen)
+int ip6_mroute_setsockopt(struct sock *sk, int optname, char __user *optval, unsigned int optlen)
{
int ret;
struct mif6ctl vif;
}
static int do_ipv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct ipv6_pinfo *np = inet6_sk(sk);
struct net *net = sock_net(sk);
}
int ipv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
int err;
#ifdef CONFIG_COMPAT
int compat_ipv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
int err;
&icmp6h, NULL,
send_sllao ? ND_OPT_SOURCE_LL_ADDR : 0);
}
-EXPORT_SYMBOL(ndisc_send_rs);
static void ndisc_error_report(struct neighbour *neigh, struct sk_buff *skb)
}
}
-int ndisc_ifinfo_sysctl_change(struct ctl_table *ctl, int write, struct file * filp, void __user *buffer, size_t *lenp, loff_t *ppos)
+int ndisc_ifinfo_sysctl_change(struct ctl_table *ctl, int write, void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct net_device *dev = ctl->extra1;
struct inet6_dev *idev;
ndisc_warn_deprecated_sysctl(ctl, "syscall", dev ? dev->name : "default");
if (strcmp(ctl->procname, "retrans_time") == 0)
- ret = proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(ctl, write, buffer, lenp, ppos);
else if (strcmp(ctl->procname, "base_reachable_time") == 0)
ret = proc_dointvec_jiffies(ctl, write,
- filp, buffer, lenp, ppos);
+ buffer, lenp, ppos);
else if ((strcmp(ctl->procname, "retrans_time_ms") == 0) ||
(strcmp(ctl->procname, "base_reachable_time_ms") == 0))
ret = proc_dointvec_ms_jiffies(ctl, write,
- filp, buffer, lenp, ppos);
+ buffer, lenp, ppos);
else
ret = -1;
static int do_rawv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct raw6_sock *rp = raw6_sk(sk);
int val;
}
static int rawv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
switch(level) {
case SOL_RAW:
#ifdef CONFIG_COMPAT
static int compat_rawv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
switch (level) {
case SOL_RAW:
#ifdef CONFIG_SYSCTL
static
-int ipv6_sysctl_rtcache_flush(ctl_table *ctl, int write, struct file * filp,
+int ipv6_sysctl_rtcache_flush(ctl_table *ctl, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
struct net *net = current->nsproxy->net_ns;
int delay = net->ipv6.sysctl.flush_delay;
if (write) {
- proc_dointvec(ctl, write, filp, buffer, lenp, ppos);
+ proc_dointvec(ctl, write, buffer, lenp, ppos);
fib6_run_gc(delay <= 0 ? ~0UL : (unsigned long)delay, net);
return 0;
} else
* Roger Venning <r.venning@telstra.com>: 6to4 support
* Nate Thompson <nate@thebog.net>: 6to4 support
* Fred Templin <fred.l.templin@boeing.com>: isatap support
- * Sascha Hlusiak <mail@saschahlusiak.de>: stateless autoconf for isatap
*/
#include <linux/module.h>
return NULL;
}
-static void ipip6_tunnel_rs_timer(unsigned long data)
-{
- struct ip_tunnel_prl_entry *p = (struct ip_tunnel_prl_entry *) data;
- struct inet6_dev *ifp;
- struct inet6_ifaddr *addr;
-
- spin_lock(&p->lock);
- ifp = __in6_dev_get(p->tunnel->dev);
-
- read_lock_bh(&ifp->lock);
- for (addr = ifp->addr_list; addr; addr = addr->if_next) {
- struct in6_addr rtr;
-
- if (!(ipv6_addr_type(&addr->addr) & IPV6_ADDR_LINKLOCAL))
- continue;
-
- /* Send RS to guessed linklocal address of router
- *
- * Better: send to ff02::2 encapsuled in unicast directly
- * to router-v4 instead of guessing the v6 address.
- *
- * Cisco/Windows seem to not set the u/l bit correctly,
- * so we won't guess right.
- */
- ipv6_addr_set(&rtr, htonl(0xFE800000), 0, 0, 0);
- if (!__ipv6_isatap_ifid(rtr.s6_addr + 8,
- p->addr)) {
- ndisc_send_rs(p->tunnel->dev, &addr->addr, &rtr);
- }
- }
- read_unlock_bh(&ifp->lock);
-
- mod_timer(&p->rs_timer, jiffies + HZ * p->rs_delay);
- spin_unlock(&p->lock);
-
- return;
-}
-
static struct ip_tunnel_prl_entry *
__ipip6_tunnel_locate_prl(struct ip_tunnel *t, __be32 addr)
{
c = 0;
for (prl = t->prl; prl; prl = prl->next) {
- if (c > cmax)
+ if (c >= cmax)
break;
if (kprl.addr != htonl(INADDR_ANY) && prl->addr != kprl.addr)
continue;
kp[c].addr = prl->addr;
kp[c].flags = prl->flags;
- kp[c].rs_delay = prl->rs_delay;
c++;
if (kprl.addr != htonl(INADDR_ANY))
break;
}
p->next = t->prl;
- p->tunnel = t;
t->prl = p;
t->prl_count++;
-
- spin_lock_init(&p->lock);
- setup_timer(&p->rs_timer, ipip6_tunnel_rs_timer, (unsigned long) p);
update:
p->addr = a->addr;
p->flags = a->flags;
- p->rs_delay = a->rs_delay;
- if (p->rs_delay == 0)
- p->rs_delay = IPTUNNEL_RS_DEFAULT_DELAY;
- spin_lock(&p->lock);
- del_timer(&p->rs_timer);
- if (p->flags & PRL_DEFAULT)
- mod_timer(&p->rs_timer, jiffies + 1);
- spin_unlock(&p->lock);
out:
write_unlock(&ipip6_lock);
return err;
if ((*p)->addr == a->addr) {
x = *p;
*p = x->next;
- spin_lock(&x->lock);
- del_timer(&x->rs_timer);
- spin_unlock(&x->lock);
kfree(x);
t->prl_count--;
goto out;
while (t->prl) {
x = t->prl;
t->prl = t->prl->next;
- spin_lock(&x->lock);
- del_timer(&x->rs_timer);
- spin_unlock(&x->lock);
kfree(x);
t->prl_count--;
}
struct in6_addr *addr6;
int addr_type;
- if (tunnel->recursion++) {
- stats->collisions++;
- goto tx_error;
- }
-
if (skb->protocol != htons(ETH_P_IPV6))
goto tx_error;
ip_rt_put(rt);
stats->tx_dropped++;
dev_kfree_skb(skb);
- tunnel->recursion--;
return NETDEV_TX_OK;
}
if (skb->sk)
nf_reset(skb);
IPTUNNEL_XMIT();
- tunnel->recursion--;
return NETDEV_TX_OK;
tx_error_icmp:
tx_error:
stats->tx_errors++;
dev_kfree_skb(skb);
- tunnel->recursion--;
return NETDEV_TX_OK;
}
* Socket option code for UDP
*/
int udpv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level == SOL_UDP || level == SOL_UDPLITE)
return udp_lib_setsockopt(sk, level, optname, optval, optlen,
#ifdef CONFIG_COMPAT
int compat_udpv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
if (level == SOL_UDP || level == SOL_UDPLITE)
return udp_lib_setsockopt(sk, level, optname, optval, optlen,
extern int udpv6_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
extern int udpv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
#ifdef CONFIG_COMPAT
extern int compat_udpv6_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen);
+ char __user *optval, unsigned int optlen);
extern int compat_udpv6_getsockopt(struct sock *sk, int level, int optname,
char __user *optval, int __user *optlen);
#endif
* socket object. */
static int ipx_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
int opt;
*
*/
static int irda_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct irda_sock *self = irda_sk(sk);
/* For other sysctl, I've no idea of the range. Maybe Dag could help
* us on that - Jean II */
-static int do_devname(ctl_table *table, int write, struct file *filp,
+static int do_devname(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int ret;
- ret = proc_dostring(table, write, filp, buffer, lenp, ppos);
+ ret = proc_dostring(table, write, buffer, lenp, ppos);
if (ret == 0 && write) {
struct ias_value *val;
}
-static int do_discovery(ctl_table *table, int write, struct file *filp,
+static int do_discovery(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int ret;
- ret = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
if (ret)
return ret;
/* getsockopt and setsockopt */
static int iucv_sock_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct iucv_sock *iucv = iucv_sk(sk);
* Set various connection specific parameters.
*/
static int llc_ui_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct llc_sock *llc = llc_sk(sk);
reason_code = le16_to_cpu(mgmt->u.disassoc.reason_code);
- printk(KERN_DEBUG "%s: disassociated (Reason: %u)\n",
- sdata->dev->name, reason_code);
+ printk(KERN_DEBUG "%s: disassociated from %pM (Reason: %u)\n",
+ sdata->dev->name, mgmt->sa, reason_code);
ieee80211_set_disassoc(sdata, false);
return RX_MGMT_CFG80211_DISASSOC;
/* direct probe may be part of the association flow */
if (wk && wk->state == IEEE80211_MGD_STATE_PROBE) {
- printk(KERN_DEBUG "%s direct probe responded\n",
+ printk(KERN_DEBUG "%s: direct probe responded\n",
sdata->dev->name);
wk->tries = 0;
wk->state = IEEE80211_MGD_STATE_AUTH;
struct ieee80211_mgd_work *wk;
const u8 *bssid = NULL;
- printk(KERN_DEBUG "%s: deauthenticating by local choice (reason=%d)\n",
- sdata->dev->name, req->reason_code);
-
mutex_lock(&ifmgd->mtx);
if (ifmgd->associated && &ifmgd->associated->cbss == req->bss) {
mutex_unlock(&ifmgd->mtx);
+ printk(KERN_DEBUG "%s: deauthenticating from %pM by local choice (reason=%d)\n",
+ sdata->dev->name, bssid, req->reason_code);
+
ieee80211_send_deauth_disassoc(sdata, bssid,
IEEE80211_STYPE_DEAUTH, req->reason_code,
cookie);
{
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
- printk(KERN_DEBUG "%s: disassociating by local choice (reason=%d)\n",
- sdata->dev->name, req->reason_code);
-
mutex_lock(&ifmgd->mtx);
/*
return -ENOLINK;
}
+ printk(KERN_DEBUG "%s: disassociating from %pM by local choice (reason=%d)\n",
+ sdata->dev->name, req->bss->bssid, req->reason_code);
+
ieee80211_set_disassoc(sdata, false);
mutex_unlock(&ifmgd->mtx);
bss->dtim_period = tim_ie->dtim_period;
}
- /* set default value for buggy APs */
- if (!elems->tim || bss->dtim_period == 0)
+ /* set default value for buggy AP/no TIM element */
+ if (bss->dtim_period == 0)
bss->dtim_period = 1;
bss->supp_rates_len = 0;
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)tx->skb->data;
u32 staflags;
- if (unlikely(!sta || ieee80211_is_probe_resp(hdr->frame_control)))
+ if (unlikely(!sta || ieee80211_is_probe_resp(hdr->frame_control)
+ || ieee80211_is_auth(hdr->frame_control)
+ || ieee80211_is_assoc_resp(hdr->frame_control)
+ || ieee80211_is_reassoc_resp(hdr->frame_control)))
return TX_CONTINUE;
staflags = get_sta_flags(sta);
static int
-proc_do_defense_mode(ctl_table *table, int write, struct file * filp,
+proc_do_defense_mode(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int *valp = table->data;
int val = *valp;
int rc;
- rc = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ rc = proc_dointvec(table, write, buffer, lenp, ppos);
if (write && (*valp != val)) {
if ((*valp < 0) || (*valp > 3)) {
/* Restore the correct value */
static int
-proc_do_sync_threshold(ctl_table *table, int write, struct file *filp,
+proc_do_sync_threshold(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int *valp = table->data;
/* backup the value first */
memcpy(val, valp, sizeof(val));
- rc = proc_dointvec(table, write, filp, buffer, lenp, ppos);
+ rc = proc_dointvec(table, write, buffer, lenp, ppos);
if (write && (valp[0] < 0 || valp[1] < 0 || valp[0] >= valp[1])) {
/* Restore the correct value */
memcpy(valp, val, sizeof(val));
static struct ctl_table nf_log_sysctl_table[NFPROTO_NUMPROTO+1];
static struct ctl_table_header *nf_log_dir_header;
-static int nf_log_proc_dostring(ctl_table *table, int write, struct file *filp,
+static int nf_log_proc_dostring(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
const struct nf_logger *logger;
table->data = "NONE";
else
table->data = logger->name;
- r = proc_dostring(table, write, filp, buffer, lenp, ppos);
+ r = proc_dostring(table, write, buffer, lenp, ppos);
mutex_unlock(&nf_log_mutex);
}
}
int nf_setsockopt(struct sock *sk, u_int8_t pf, int val, char __user *opt,
- int len)
+ unsigned int len)
{
return nf_sockopt(sk, pf, val, opt, &len, 0);
}
}
int compat_nf_setsockopt(struct sock *sk, u_int8_t pf,
- int val, char __user *opt, int len)
+ int val, char __user *opt, unsigned int len)
{
return compat_nf_sockopt(sk, pf, val, opt, &len, 0);
}
}
static int netlink_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct netlink_sock *nlk = nlk_sk(sk);
return err;
}
+void __netlink_clear_multicast_users(struct sock *ksk, unsigned int group)
+{
+ struct sock *sk;
+ struct hlist_node *node;
+ struct netlink_table *tbl = &nl_table[ksk->sk_protocol];
+
+ sk_for_each_bound(sk, node, &tbl->mc_list)
+ netlink_update_socket_mc(nlk_sk(sk), group, 0);
+}
+
/**
* netlink_clear_multicast_users - kick off multicast listeners
*
*/
void netlink_clear_multicast_users(struct sock *ksk, unsigned int group)
{
- struct sock *sk;
- struct hlist_node *node;
- struct netlink_table *tbl = &nl_table[ksk->sk_protocol];
-
netlink_table_grab();
-
- sk_for_each_bound(sk, node, &tbl->mc_list)
- netlink_update_socket_mc(nlk_sk(sk), group, 0);
-
+ __netlink_clear_multicast_users(ksk, group);
netlink_table_ungrab();
}
}
rep = __nlmsg_put(skb, NETLINK_CB(in_skb).pid, nlh->nlmsg_seq,
- NLMSG_ERROR, sizeof(struct nlmsgerr), 0);
+ NLMSG_ERROR, payload, 0);
errmsg = nlmsg_data(rep);
errmsg->error = err;
memcpy(&errmsg->msg, nlh, err ? nlh->nlmsg_len : sizeof(*nlh));
struct net *net;
BUG_ON(grp->family != family);
+ netlink_table_grab();
rcu_read_lock();
for_each_net_rcu(net)
- netlink_clear_multicast_users(net->genl_sock, grp->id);
+ __netlink_clear_multicast_users(net->genl_sock, grp->id);
rcu_read_unlock();
+ netlink_table_ungrab();
clear_bit(grp->id, mc_groups);
list_del(&grp->list);
*/
static int nr_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct nr_sock *nr = nr_sk(sk);
}
static int
-packet_setsockopt(struct socket *sock, int level, int optname, char __user *optval, int optlen)
+packet_setsockopt(struct socket *sock, int level, int optname, char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct packet_sock *po = pkt_sk(sk);
atomic_dec(&pkt_sk(sk)->mapped);
}
-static struct vm_operations_struct packet_mmap_ops = {
+static const struct vm_operations_struct packet_mmap_ops = {
.open = packet_mm_open,
.close = packet_mm_close,
};
goto drop;
}
+ /* Broadcast sending is not implemented */
+ if (pn_addr(dst) == PNADDR_BROADCAST) {
+ err = -EOPNOTSUPP;
+ goto drop;
+ }
+
skb_reset_transport_header(skb);
WARN_ON(skb_headroom(skb) & 1); /* HW assumes word alignment */
skb_push(skb, sizeof(struct phonethdr));
}
static int pep_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct pep_sock *pn = pep_sk(sk);
int val = 0, err = 0;
}
EXPORT_SYMBOL(pn_sock_unhash);
+static DEFINE_MUTEX(port_mutex);
+
static int pn_socket_bind(struct socket *sock, struct sockaddr *addr, int len)
{
struct sock *sk = sock->sk;
err = -EINVAL; /* attempt to rebind */
goto out;
}
+ WARN_ON(sk_hashed(sk));
+ mutex_lock(&port_mutex);
err = sk->sk_prot->get_port(sk, pn_port(handle));
if (err)
- goto out;
+ goto out_port;
/* get_port() sets the port, bind() sets the address if applicable */
pn->sobject = pn_object(saddr, pn_port(pn->sobject));
/* Enable RX on the socket */
sk->sk_prot->hash(sk);
+out_port:
+ mutex_unlock(&port_mutex);
out:
release_sock(sk);
return err;
};
EXPORT_SYMBOL(phonet_stream_ops);
-static DEFINE_MUTEX(port_mutex);
-
/* allocate port for a socket */
int pn_sock_get_port(struct sock *sk, unsigned short sport)
{
memset(&try_sa, 0, sizeof(struct sockaddr_pn));
try_sa.spn_family = AF_PHONET;
-
- mutex_lock(&port_mutex);
-
+ WARN_ON(!mutex_is_locked(&port_mutex));
if (!sport) {
/* search free port */
int port, pmin, pmax;
else
sock_put(tmpsk);
}
- mutex_unlock(&port_mutex);
-
/* the port must be in use already */
return -EADDRINUSE;
found:
- mutex_unlock(&port_mutex);
pn->sobject = pn_object(pn_addr(pn->sobject), sport);
return 0;
}
} while (read_seqretry(&local_port_range_lock, seq));
}
-static int proc_local_port_range(ctl_table *table, int write, struct file *filp,
+static int proc_local_port_range(ctl_table *table, int write,
void __user *buffer,
size_t *lenp, loff_t *ppos)
{
.extra2 = &local_port_range_max,
};
- ret = proc_dointvec_minmax(&tmp, write, filp, buffer, lenp, ppos);
+ ret = proc_dointvec_minmax(&tmp, write, buffer, lenp, ppos);
if (write && ret == 0) {
if (range[1] < range[0])
}
static int rds_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct rds_sock *rs = rds_sk_to_rs(sock->sk);
int ret;
#include <linux/list.h>
#include <linux/mutex.h>
#include <linux/rfkill.h>
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/miscdevice.h>
#include <linux/wait.h>
*/
static int rose_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sock *sk = sock->sk;
struct rose_sock *rose = rose_sk(sk);
* set RxRPC socket options
*/
static int rxrpc_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct rxrpc_sock *rx = rxrpc_sk(sock->sk);
unsigned min_sec_level;
* instead a error will be indicated to the user.
*/
static int sctp_setsockopt_disable_fragments(struct sock *sk,
- char __user *optval, int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
int val;
}
static int sctp_setsockopt_events(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
if (optlen > sizeof(struct sctp_event_subscribe))
return -EINVAL;
* association is closed.
*/
static int sctp_setsockopt_autoclose(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_sock *sp = sctp_sk(sk);
}
static int sctp_setsockopt_peer_addr_params(struct sock *sk,
- char __user *optval, int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
struct sctp_paddrparams params;
struct sctp_transport *trans = NULL;
*/
static int sctp_setsockopt_delayed_ack(struct sock *sk,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
struct sctp_sack_info params;
struct sctp_transport *trans = NULL;
* by the change). With TCP-style sockets, this option is inherited by
* sockets derived from a listener socket.
*/
-static int sctp_setsockopt_initmsg(struct sock *sk, char __user *optval, int optlen)
+static int sctp_setsockopt_initmsg(struct sock *sk, char __user *optval, unsigned int optlen)
{
struct sctp_initmsg sinit;
struct sctp_sock *sp = sctp_sk(sk);
* to this call if the caller is using the UDP model.
*/
static int sctp_setsockopt_default_send_param(struct sock *sk,
- char __user *optval, int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
struct sctp_sndrcvinfo info;
struct sctp_association *asoc;
* association peer's addresses.
*/
static int sctp_setsockopt_primary_addr(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_prim prim;
struct sctp_transport *trans;
* integer boolean flag.
*/
static int sctp_setsockopt_nodelay(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
int val;
* be changed.
*
*/
-static int sctp_setsockopt_rtoinfo(struct sock *sk, char __user *optval, int optlen) {
+static int sctp_setsockopt_rtoinfo(struct sock *sk, char __user *optval, unsigned int optlen)
+{
struct sctp_rtoinfo rtoinfo;
struct sctp_association *asoc;
* See [SCTP] for more information.
*
*/
-static int sctp_setsockopt_associnfo(struct sock *sk, char __user *optval, int optlen)
+static int sctp_setsockopt_associnfo(struct sock *sk, char __user *optval, unsigned int optlen)
{
struct sctp_assocparams assocparams;
* addresses and a user will receive both PF_INET6 and PF_INET type
* addresses on the socket.
*/
-static int sctp_setsockopt_mappedv4(struct sock *sk, char __user *optval, int optlen)
+static int sctp_setsockopt_mappedv4(struct sock *sk, char __user *optval, unsigned int optlen)
{
int val;
struct sctp_sock *sp = sctp_sk(sk);
* changed (effecting future associations only).
* assoc_value: This parameter specifies the maximum size in bytes.
*/
-static int sctp_setsockopt_maxseg(struct sock *sk, char __user *optval, int optlen)
+static int sctp_setsockopt_maxseg(struct sock *sk, char __user *optval, unsigned int optlen)
{
struct sctp_assoc_value params;
struct sctp_association *asoc;
* set primary request:
*/
static int sctp_setsockopt_peer_primary_addr(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_sock *sp;
struct sctp_endpoint *ep;
}
static int sctp_setsockopt_adaptation_layer(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_setadaptation adaptation;
* saved with outbound messages.
*/
static int sctp_setsockopt_context(struct sock *sk, char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_assoc_value params;
struct sctp_sock *sp;
*/
static int sctp_setsockopt_fragment_interleave(struct sock *sk,
char __user *optval,
- int optlen)
+ unsigned int optlen)
{
int val;
*/
static int sctp_setsockopt_partial_delivery_point(struct sock *sk,
char __user *optval,
- int optlen)
+ unsigned int optlen)
{
u32 val;
*/
static int sctp_setsockopt_maxburst(struct sock *sk,
char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_assoc_value params;
struct sctp_sock *sp;
* will only effect future associations on the socket.
*/
static int sctp_setsockopt_auth_chunk(struct sock *sk,
- char __user *optval,
- int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
struct sctp_authchunk val;
* endpoint requires the peer to use.
*/
static int sctp_setsockopt_hmac_ident(struct sock *sk,
- char __user *optval,
- int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
struct sctp_hmacalgo *hmacs;
u32 idents;
*/
static int sctp_setsockopt_auth_key(struct sock *sk,
char __user *optval,
- int optlen)
+ unsigned int optlen)
{
struct sctp_authkey *authkey;
struct sctp_association *asoc;
* the association shared key.
*/
static int sctp_setsockopt_active_key(struct sock *sk,
- char __user *optval,
- int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
struct sctp_authkeyid val;
struct sctp_association *asoc;
* This set option will delete a shared secret key from use.
*/
static int sctp_setsockopt_del_key(struct sock *sk,
- char __user *optval,
- int optlen)
+ char __user *optval,
+ unsigned int optlen)
{
struct sctp_authkeyid val;
struct sctp_association *asoc;
* optlen - the size of the buffer.
*/
SCTP_STATIC int sctp_setsockopt(struct sock *sk, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
int retval = 0;
unsigned long a[6];
unsigned long a0, a1;
int err;
+ unsigned int len;
if (call < 1 || call > SYS_ACCEPT4)
return -EINVAL;
+ len = nargs[call];
+ if (len > sizeof(a))
+ return -EINVAL;
+
/* copy_from_user should be SMP safe. */
- if (copy_from_user(a, args, nargs[call]))
+ if (copy_from_user(a, args, len))
return -EFAULT;
audit_socketcall(nargs[call] / sizeof(unsigned long), a);
}
int kernel_setsockopt(struct socket *sock, int level, int optname,
- char *optval, int optlen)
+ char *optval, unsigned int optlen)
{
mm_segment_t oldfs = get_fs();
int err;
/**
* rpc_run_bc_task - Allocate a new RPC task for backchannel use, then run
* rpc_execute against it
- * @ops: RPC call ops
+ * @req: RPC request
+ * @tk_ops: RPC call ops
*/
struct rpc_task *rpc_run_bc_task(struct rpc_rqst *req,
- const struct rpc_call_ops *tk_ops)
+ const struct rpc_call_ops *tk_ops)
{
struct rpc_task *task;
struct xdr_buf *xbufp = &req->rq_snd_buf;
}
}
-static int proc_do_xprt(ctl_table *table, int write, struct file *file,
+static int proc_do_xprt(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
char tmpbuf[256];
}
static int
-proc_dodebug(ctl_table *table, int write, struct file *file,
+proc_dodebug(ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
char tmpbuf[20], c, *s;
* current value.
*/
static int read_reset_stat(ctl_table *table, int write,
- struct file *filp, void __user *buffer, size_t *lenp,
+ void __user *buffer, size_t *lenp,
loff_t *ppos)
{
atomic_t *stat = (atomic_t *)table->data;
*/
static int setsockopt(struct socket *sock,
- int lvl, int opt, char __user *ov, int ol)
+ int lvl, int opt, char __user *ov, unsigned int ol)
{
struct sock *sk = sock->sk;
struct tipc_port *tport = tipc_sk_port(sk);
wdev->conn->params.ssid = wdev->ssid;
wdev->conn->params.ssid_len = connect->ssid_len;
- /* don't care about result -- but fill bssid & channel */
- if (!wdev->conn->params.bssid || !wdev->conn->params.channel)
- bss = cfg80211_get_conn_bss(wdev);
+ /* see if we have the bss already */
+ bss = cfg80211_get_conn_bss(wdev);
wdev->sme_state = CFG80211_SME_CONNECTING;
wdev->connect_keys = connkeys;
wdev->wext.connect.ie = wdev->wext.ie;
wdev->wext.connect.ie_len = wdev->wext.ie_len;
- wdev->wext.connect.privacy = wdev->wext.default_key != -1;
if (wdev->wext.keys) {
wdev->wext.keys->def = wdev->wext.default_key;
wdev->wext.keys->defmgmt = wdev->wext.default_mgmt_key;
+ if (wdev->wext.default_key != -1)
+ wdev->wext.connect.privacy = true;
}
if (!wdev->wext.connect.ssid_len)
data->flags = 1;
data->length = wdev->wext.connect.ssid_len;
memcpy(ssid, wdev->wext.connect.ssid, data->length);
- } else
- data->flags = 0;
+ }
wdev_unlock(wdev);
return 0;
wdev_lock(wdev);
if (wdev->current_bss)
memcpy(ap_addr->sa_data, wdev->current_bss->pub.bssid, ETH_ALEN);
- else if (wdev->wext.connect.bssid)
- memcpy(ap_addr->sa_data, wdev->wext.connect.bssid, ETH_ALEN);
else
memset(ap_addr->sa_data, 0, ETH_ALEN);
wdev_unlock(wdev);
/*
* Get statistics out of the driver
*/
-static struct iw_statistics *get_wireless_stats(struct net_device *dev)
+struct iw_statistics *get_wireless_stats(struct net_device *dev)
{
/* New location */
if ((dev->wireless_handlers != NULL) &&
essid_compat = 1;
else if (IW_IS_SET(cmd) && (iwp->length != 0)) {
char essid[IW_ESSID_MAX_SIZE + 1];
+ unsigned int len;
+ len = iwp->length * descr->token_size;
- err = copy_from_user(essid, iwp->pointer,
- iwp->length *
- descr->token_size);
+ if (len > IW_ESSID_MAX_SIZE)
+ return -EFAULT;
+
+ err = copy_from_user(essid, iwp->pointer, len);
if (err)
return -EFAULT;
*/
static int x25_setsockopt(struct socket *sock, int level, int optname,
- char __user *optval, int optlen)
+ char __user *optval, unsigned int optlen)
{
int opt;
struct sock *sk = sock->sk;
return -EPERM;
}
-static struct file_operations mark_ops = {
+static const struct file_operations mark_ops = {
.open = my_open,
};
struct cgroup_subsys devices_subsys;
static int devcgroup_can_attach(struct cgroup_subsys *ss,
- struct cgroup *new_cgroup, struct task_struct *task)
+ struct cgroup *new_cgroup, struct task_struct *task,
+ bool threadgroup)
{
if (current != task && !capable(CAP_SYS_ADMIN))
return -EPERM;
return ima_show_htable_value(buf, count, ppos, &ima_htable.violations);
}
-static struct file_operations ima_htable_violations_ops = {
+static const struct file_operations ima_htable_violations_ops = {
.read = ima_show_htable_violations
};
}
-static struct file_operations ima_measurements_count_ops = {
+static const struct file_operations ima_measurements_count_ops = {
.read = ima_show_measurements_count
};
return seq_open(file, &ima_measurments_seqops);
}
-static struct file_operations ima_measurements_ops = {
+static const struct file_operations ima_measurements_ops = {
.open = ima_measurements_open,
.read = seq_read,
.llseek = seq_lseek,
return seq_open(file, &ima_ascii_measurements_seqops);
}
-static struct file_operations ima_ascii_measurements_ops = {
+static const struct file_operations ima_ascii_measurements_ops = {
.open = ima_ascii_measurements_open,
.read = seq_read,
.llseek = seq_lseek,
return 0;
}
-static struct file_operations ima_measure_policy_ops = {
+static const struct file_operations ima_measure_policy_ops = {
.open = ima_open_policy,
.write = ima_write_policy,
.release = ima_release_policy
char *name1, char *name2)
{
if (!ipv6_addr_any(addr))
- audit_log_format(ab, " %s=%pI6", name1, addr);
+ audit_log_format(ab, " %s=%pI6c", name1, addr);
if (port)
audit_log_format(ab, " %s=%d", name2, ntohs(port));
}
* sysctl handler which just sets dac_mmap_min_addr = the new value and then
* calls update_mmap_min_addr() so non MAP_FIXED hints get rounded properly
*/
-int mmap_min_addr_handler(struct ctl_table *table, int write, struct file *filp,
+int mmap_min_addr_handler(struct ctl_table *table, int write,
void __user *buffer, size_t *lenp, loff_t *ppos)
{
int ret;
- ret = proc_doulongvec_minmax(table, write, filp, buffer, lenp, ppos);
+ ret = proc_doulongvec_minmax(table, write, buffer, lenp, ppos);
update_mmap_min_addr();
/* Wake up the parent if it is waiting so that it can recheck
* wait permission to the new task SID. */
read_lock(&tasklist_lock);
- wake_up_interruptible(¤t->real_parent->signal->wait_chldexit);
+ __wake_up_parent(current, current->real_parent);
read_unlock(&tasklist_lock);
}
client = i2c_new_device(adapter, &info);
if (!client)
return -ENODEV;
+ /*
+ * We know the driver is already loaded, so the device should be
+ * already bound. If not it means binding failed, and then there
+ * is no point in keeping the device instantiated.
+ */
+ if (!client->driver) {
+ i2c_unregister_device(client);
+ return -ENODEV;
+ }
/*
* Let i2c-core delete that device on driver removal.
return 0;
}
-static int pxa2xx_ac97_suspend(struct platform_device *dev, pm_message_t state)
+static int pxa2xx_ac97_suspend(struct device *dev)
{
- struct snd_card *card = platform_get_drvdata(dev);
+ struct snd_card *card = dev_get_drvdata(dev);
int ret = 0;
if (card)
return ret;
}
-static int pxa2xx_ac97_resume(struct platform_device *dev)
+static int pxa2xx_ac97_resume(struct device *dev)
{
- struct snd_card *card = platform_get_drvdata(dev);
+ struct snd_card *card = dev_get_drvdata(dev);
int ret = 0;
if (card)
return ret;
}
-#else
-#define pxa2xx_ac97_suspend NULL
-#define pxa2xx_ac97_resume NULL
+static struct dev_pm_ops pxa2xx_ac97_pm_ops = {
+ .suspend = pxa2xx_ac97_suspend,
+ .resume = pxa2xx_ac97_resume,
+};
#endif
static int __devinit pxa2xx_ac97_probe(struct platform_device *dev)
static struct platform_driver pxa2xx_ac97_driver = {
.probe = pxa2xx_ac97_probe,
.remove = __devexit_p(pxa2xx_ac97_remove),
- .suspend = pxa2xx_ac97_suspend,
- .resume = pxa2xx_ac97_resume,
.driver = {
.name = "pxa2xx-ac97",
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxa2xx_ac97_pm_ops,
+#endif
},
};
return 0;
}
-static struct vm_operations_struct snd_pcm_vm_ops_status =
+static const struct vm_operations_struct snd_pcm_vm_ops_status =
{
.fault = snd_pcm_mmap_status_fault,
};
return 0;
}
-static struct vm_operations_struct snd_pcm_vm_ops_control =
+static const struct vm_operations_struct snd_pcm_vm_ops_control =
{
.fault = snd_pcm_mmap_control_fault,
};
return 0;
}
-static struct vm_operations_struct snd_pcm_vm_ops_data =
+static const struct vm_operations_struct snd_pcm_vm_ops_data =
{
.open = snd_pcm_mmap_data_open,
.close = snd_pcm_mmap_data_close,
* mmap the DMA buffer on I/O memory area
*/
#if SNDRV_PCM_INFO_MMAP_IOMEM
-static struct vm_operations_struct snd_pcm_vm_ops_data_mmio =
+static const struct vm_operations_struct snd_pcm_vm_ops_data_mmio =
{
.open = snd_pcm_mmap_data_open,
.close = snd_pcm_mmap_data_close,
return 0;
}
-static int __exit hal2_remove(struct platform_device *pdev)
+static int __devexit hal2_remove(struct platform_device *pdev)
{
struct snd_card *card = platform_get_drvdata(pdev);
return 0;
}
-static int __exit snd_sgio2audio_remove(struct platform_device *pdev)
+static int __devexit snd_sgio2audio_remove(struct platform_device *pdev)
{
struct snd_card *card = platform_get_drvdata(pdev);
static int atc_line_surround_unmute(struct ct_atc *atc, unsigned char state)
{
- return atc_daio_unmute(atc, state, LINEO4);
+ return atc_daio_unmute(atc, state, LINEO2);
}
static int atc_line_clfe_unmute(struct ct_atc *atc, unsigned char state)
static int atc_line_rear_unmute(struct ct_atc *atc, unsigned char state)
{
- return atc_daio_unmute(atc, state, LINEO2);
+ return atc_daio_unmute(atc, state, LINEO4);
}
static int atc_line_in_unmute(struct ct_atc *atc, unsigned char state)
Control interface
******************************************************************************/
-#ifndef ECHOCARD_HAS_VMIXER
+#if !defined(ECHOCARD_HAS_VMIXER) || defined(ECHOCARD_HAS_LINE_OUT_GAIN)
/******************* PCM output volume *******************/
static int snd_echo_output_gain_info(struct snd_kcontrol *kcontrol,
return changed;
}
+#ifdef ECHOCARD_HAS_LINE_OUT_GAIN
+/* On the Mia this one controls the line-out volume */
+static struct snd_kcontrol_new snd_echo_line_output_gain __devinitdata = {
+ .name = "Line Playback Volume",
+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
+ .access = SNDRV_CTL_ELEM_ACCESS_READWRITE |
+ SNDRV_CTL_ELEM_ACCESS_TLV_READ,
+ .info = snd_echo_output_gain_info,
+ .get = snd_echo_output_gain_get,
+ .put = snd_echo_output_gain_put,
+ .tlv = {.p = db_scale_output_gain},
+};
+#else
static struct snd_kcontrol_new snd_echo_pcm_output_gain __devinitdata = {
.name = "PCM Playback Volume",
.iface = SNDRV_CTL_ELEM_IFACE_MIXER,
.put = snd_echo_output_gain_put,
.tlv = {.p = db_scale_output_gain},
};
-
#endif
+#endif /* !ECHOCARD_HAS_VMIXER || ECHOCARD_HAS_LINE_OUT_GAIN */
+
#ifdef ECHOCARD_HAS_INPUT_GAIN
snd_echo_vmixer.count = num_pipes_out(chip) * num_busses_out(chip);
if ((err = snd_ctl_add(chip->card, snd_ctl_new1(&snd_echo_vmixer, chip))) < 0)
goto ctl_error;
-#else
- if ((err = snd_ctl_add(chip->card, snd_ctl_new1(&snd_echo_pcm_output_gain, chip))) < 0)
+#ifdef ECHOCARD_HAS_LINE_OUT_GAIN
+ err = snd_ctl_add(chip->card,
+ snd_ctl_new1(&snd_echo_line_output_gain, chip));
+ if (err < 0)
goto ctl_error;
#endif
+#else /* ECHOCARD_HAS_VMIXER */
+ err = snd_ctl_add(chip->card,
+ snd_ctl_new1(&snd_echo_pcm_output_gain, chip));
+ if (err < 0)
+ goto ctl_error;
+#endif /* ECHOCARD_HAS_VMIXER */
#ifdef ECHOCARD_HAS_INPUT_GAIN
if ((err = snd_ctl_add(chip->card, snd_ctl_new1(&snd_echo_line_input_gain, chip))) < 0)
#define ECHOCARD_HAS_ADAT FALSE
#define ECHOCARD_HAS_STEREO_BIG_ENDIAN32
#define ECHOCARD_HAS_MIDI
+#define ECHOCARD_HAS_LINE_OUT_GAIN
/* Pipe indexes */
#define PX_ANALOG_OUT 0 /* 8 */
* white-list for enable_msi
*/
static struct snd_pci_quirk msi_white_list[] __devinitdata = {
+ SND_PCI_QUIRK(0x103c, 0x30f7, "HP Pavilion dv4t-1300", 1),
SND_PCI_QUIRK(0x103c, 0x3607, "HP Compa CQ40", 1),
{}
};
return 0;
}
+/*
+ * HP Touchsmart
+ * port-A (0x11) - front hp-out
+ * port-B (0x14) - unused
+ * port-C (0x15) - unused
+ * port-D (0x12) - rear line out
+ * port-E (0x1c) - front mic-in
+ * port-F (0x16) - Internal speakers
+ * digital-mic (0x17) - Internal mic
+ */
+
+static struct hda_verb ad1984a_touchsmart_verbs[] = {
+ /* DACs; unmute as default */
+ {0x03, AC_VERB_SET_AMP_GAIN_MUTE, 0x27}, /* 0dB */
+ {0x04, AC_VERB_SET_AMP_GAIN_MUTE, 0x27}, /* 0dB */
+ /* Port-A (HP) mixer - route only from analog mixer */
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
+ /* Port-A pin */
+ {0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
+ /* Port-A (HP) pin - always unmuted */
+ {0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ /* Port-E (int speaker) mixer - route only from analog mixer */
+ {0x25, AC_VERB_SET_AMP_GAIN_MUTE, 0x03},
+ /* Port-E pin */
+ {0x1c, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ {0x1c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
+ {0x1c, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
+ /* Port-F (int speaker) mixer - route only from analog mixer */
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x0b, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(1)},
+ /* Port-F pin */
+ {0x16, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
+ {0x16, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
+ /* Analog mixer; mute as default */
+ {0x20, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
+ {0x20, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
+ {0x20, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)},
+ {0x20, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)},
+ {0x20, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)},
+ {0x20, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)},
+ /* Analog Mix output amp */
+ {0x21, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
+ /* capture sources */
+ /* {0x0c, AC_VERB_SET_CONNECT_SEL, 0x0}, */ /* set via unsol */
+ {0x0c, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
+ {0x0d, AC_VERB_SET_CONNECT_SEL, 0x0},
+ {0x0d, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
+ /* unsolicited event for pin-sense */
+ {0x11, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | AD1884A_HP_EVENT},
+ {0x1c, AC_VERB_SET_UNSOLICITED_ENABLE, AC_USRSP_EN | AD1884A_MIC_EVENT},
+ /* allow to touch GPIO1 (for mute control) */
+ {0x01, AC_VERB_SET_GPIO_MASK, 0x02},
+ {0x01, AC_VERB_SET_GPIO_DIRECTION, 0x02},
+ {0x01, AC_VERB_SET_GPIO_DATA, 0x02}, /* first muted */
+ /* internal mic - dmic */
+ {0x17, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
+ /* set magic COEFs for dmic */
+ {0x01, AC_VERB_SET_COEF_INDEX, 0x13f7},
+ {0x01, AC_VERB_SET_PROC_COEF, 0x08},
+ { } /* end */
+};
+
+static struct snd_kcontrol_new ad1984a_touchsmart_mixers[] = {
+ HDA_CODEC_VOLUME("Master Playback Volume", 0x21, 0x0, HDA_OUTPUT),
+/* HDA_CODEC_MUTE("Master Playback Switch", 0x21, 0x0, HDA_OUTPUT),*/
+ {
+ .iface = SNDRV_CTL_ELEM_IFACE_MIXER,
+ .name = "Master Playback Switch",
+ .info = snd_hda_mixer_amp_switch_info,
+ .get = snd_hda_mixer_amp_switch_get,
+ .put = ad1884a_mobile_master_sw_put,
+ .private_value = HDA_COMPOSE_AMP_VAL(0x21, 3, 0, HDA_OUTPUT),
+ },
+ HDA_CODEC_VOLUME("PCM Playback Volume", 0x20, 0x5, HDA_INPUT),
+ HDA_CODEC_MUTE("PCM Playback Switch", 0x20, 0x5, HDA_INPUT),
+ HDA_CODEC_VOLUME("Capture Volume", 0x0c, 0x0, HDA_OUTPUT),
+ HDA_CODEC_MUTE("Capture Switch", 0x0c, 0x0, HDA_OUTPUT),
+ HDA_CODEC_VOLUME("Mic Boost", 0x25, 0x0, HDA_OUTPUT),
+ HDA_CODEC_VOLUME("Internal Mic Boost", 0x17, 0x0, HDA_INPUT),
+ { } /* end */
+};
+
+/* switch to external mic if plugged */
+static void ad1984a_touchsmart_automic(struct hda_codec *codec)
+{
+ if (snd_hda_codec_read(codec, 0x1c, 0,
+ AC_VERB_GET_PIN_SENSE, 0) & 0x80000000) {
+ snd_hda_codec_write(codec, 0x0c, 0,
+ AC_VERB_SET_CONNECT_SEL, 0x4);
+ } else {
+ snd_hda_codec_write(codec, 0x0c, 0,
+ AC_VERB_SET_CONNECT_SEL, 0x5);
+ }
+}
+
+
+/* unsolicited event for HP jack sensing */
+static void ad1984a_touchsmart_unsol_event(struct hda_codec *codec,
+ unsigned int res)
+{
+ switch (res >> 26) {
+ case AD1884A_HP_EVENT:
+ ad1884a_hp_automute(codec);
+ break;
+ case AD1884A_MIC_EVENT:
+ ad1984a_touchsmart_automic(codec);
+ break;
+ }
+}
+
+/* initialize jack-sensing, too */
+static int ad1984a_touchsmart_init(struct hda_codec *codec)
+{
+ ad198x_init(codec);
+ ad1884a_hp_automute(codec);
+ ad1984a_touchsmart_automic(codec);
+ return 0;
+}
+
+
/*
*/
AD1884A_LAPTOP,
AD1884A_MOBILE,
AD1884A_THINKPAD,
+ AD1984A_TOUCHSMART,
AD1884A_MODELS
};
[AD1884A_LAPTOP] = "laptop",
[AD1884A_MOBILE] = "mobile",
[AD1884A_THINKPAD] = "thinkpad",
+ [AD1984A_TOUCHSMART] = "touchsmart",
};
static struct snd_pci_quirk ad1884a_cfg_tbl[] = {
SND_PCI_QUIRK_MASK(0x103c, 0xff00, 0x3600, "HP laptop", AD1884A_LAPTOP),
SND_PCI_QUIRK_MASK(0x103c, 0xfff0, 0x7010, "HP laptop", AD1884A_MOBILE),
SND_PCI_QUIRK(0x17aa, 0x20ac, "Thinkpad X300", AD1884A_THINKPAD),
+ SND_PCI_QUIRK(0x103c, 0x2a82, "Touchsmart", AD1984A_TOUCHSMART),
{}
};
codec->patch_ops.unsol_event = ad1984a_thinkpad_unsol_event;
codec->patch_ops.init = ad1984a_thinkpad_init;
break;
+ case AD1984A_TOUCHSMART:
+ spec->mixers[0] = ad1984a_touchsmart_mixers;
+ spec->init_verbs[0] = ad1984a_touchsmart_verbs;
+ spec->multiout.dig_out_nid = 0;
+ codec->patch_ops.unsol_event = ad1984a_touchsmart_unsol_event;
+ codec->patch_ops.init = ad1984a_touchsmart_init;
+ /* set the upper-limit for mixer amp to 0dB for avoiding the
+ * possible damage by overloading
+ */
+ snd_hda_override_amp_caps(codec, 0x20, HDA_INPUT,
+ (0x17 << AC_AMPCAP_OFFSET_SHIFT) |
+ (0x17 << AC_AMPCAP_NUM_STEPS_SHIFT) |
+ (0x05 << AC_AMPCAP_STEP_SIZE_SHIFT) |
+ (1 << AC_AMPCAP_MUTE_SHIFT));
+ break;
}
return 0;
};
static struct hda_input_mux cxt5045_capture_source_benq = {
- .num_items = 3,
+ .num_items = 5,
.items = {
{ "IntMic", 0x1 },
{ "ExtMic", 0x2 },
{ "LineIn", 0x3 },
+ { "CD", 0x4 },
+ { "Mixer", 0x0 },
}
};
};
static struct snd_kcontrol_new cxt5045_benq_mixers[] = {
+ HDA_CODEC_VOLUME("CD Capture Volume", 0x1a, 0x04, HDA_INPUT),
+ HDA_CODEC_MUTE("CD Capture Switch", 0x1a, 0x04, HDA_INPUT),
+ HDA_CODEC_VOLUME("CD Playback Volume", 0x17, 0x4, HDA_INPUT),
+ HDA_CODEC_MUTE("CD Playback Switch", 0x17, 0x4, HDA_INPUT),
+
HDA_CODEC_VOLUME("Line In Capture Volume", 0x1a, 0x03, HDA_INPUT),
HDA_CODEC_MUTE("Line In Capture Switch", 0x1a, 0x03, HDA_INPUT),
HDA_CODEC_VOLUME("Line In Playback Volume", 0x17, 0x3, HDA_INPUT),
HDA_CODEC_MUTE("Line In Playback Switch", 0x17, 0x3, HDA_INPUT),
+ HDA_CODEC_VOLUME("Mixer Capture Volume", 0x1a, 0x0, HDA_INPUT),
+ HDA_CODEC_MUTE("Mixer Capture Switch", 0x1a, 0x0, HDA_INPUT),
+
{}
};
.init_hook = alc268_toshiba_automute,
},
[ALC268_ACER] = {
- .mixers = { alc268_acer_mixer, alc268_capture_nosrc_mixer,
+ .mixers = { alc268_acer_mixer, alc268_capture_alt_mixer,
alc268_beep_mixer },
.init_verbs = { alc268_base_init_verbs, alc268_eapd_verbs,
alc268_acer_verbs },
SND_PCI_QUIRK(0x105b, 0x0cd6, "Foxconn", ALC662_ECS),
SND_PCI_QUIRK(0x105b, 0x0d47, "Foxconn 45CMX/45GMX/45CMX-K",
ALC662_3ST_6ch_DIG),
+ SND_PCI_QUIRK(0x1179, 0xff6e, "Toshiba NB200", ALC663_ASUS_MODE4),
SND_PCI_QUIRK(0x144d, 0xca00, "Samsung NC10", ALC272_SAMSUNG_NC10),
SND_PCI_QUIRK(0x1458, 0xa002, "Gigabyte 945GCM-S2L",
ALC662_3ST_6ch_DIG),
* BIOS auto configuration
*/
+/* convert from MIX nid to DAC */
+static inline hda_nid_t alc662_mix_to_dac(hda_nid_t nid)
+{
+ if (nid == 0x0f)
+ return 0x02;
+ else if (nid >= 0x0c && nid <= 0x0e)
+ return nid - 0x0c + 0x02;
+ else
+ return 0;
+}
+
+/* get MIX nid connected to the given pin targeted to DAC */
+static hda_nid_t alc662_dac_to_mix(struct hda_codec *codec, hda_nid_t pin,
+ hda_nid_t dac)
+{
+ hda_nid_t mix[4];
+ int i, num;
+
+ num = snd_hda_get_connections(codec, pin, mix, ARRAY_SIZE(mix));
+ for (i = 0; i < num; i++) {
+ if (alc662_mix_to_dac(mix[i]) == dac)
+ return mix[i];
+ }
+ return 0;
+}
+
+/* look for an empty DAC slot */
+static hda_nid_t alc662_look_for_dac(struct hda_codec *codec, hda_nid_t pin)
+{
+ struct alc_spec *spec = codec->spec;
+ hda_nid_t srcs[5];
+ int i, j, num;
+
+ num = snd_hda_get_connections(codec, pin, srcs, ARRAY_SIZE(srcs));
+ if (num < 0)
+ return 0;
+ for (i = 0; i < num; i++) {
+ hda_nid_t nid = alc662_mix_to_dac(srcs[i]);
+ if (!nid)
+ continue;
+ for (j = 0; j < spec->multiout.num_dacs; j++)
+ if (spec->multiout.dac_nids[j] == nid)
+ break;
+ if (j >= spec->multiout.num_dacs)
+ return nid;
+ }
+ return 0;
+}
+
+/* fill in the dac_nids table from the parsed pin configuration */
+static int alc662_auto_fill_dac_nids(struct hda_codec *codec,
+ const struct auto_pin_cfg *cfg)
+{
+ struct alc_spec *spec = codec->spec;
+ int i;
+ hda_nid_t dac;
+
+ spec->multiout.dac_nids = spec->private_dac_nids;
+ for (i = 0; i < cfg->line_outs; i++) {
+ dac = alc662_look_for_dac(codec, cfg->line_out_pins[i]);
+ if (!dac)
+ continue;
+ spec->multiout.dac_nids[spec->multiout.num_dacs++] = dac;
+ }
+ return 0;
+}
+
+static int alc662_add_vol_ctl(struct alc_spec *spec, const char *pfx,
+ hda_nid_t nid, unsigned int chs)
+{
+ char name[32];
+ sprintf(name, "%s Playback Volume", pfx);
+ return add_control(spec, ALC_CTL_WIDGET_VOL, name,
+ HDA_COMPOSE_AMP_VAL(nid, chs, 0, HDA_OUTPUT));
+}
+
+static int alc662_add_sw_ctl(struct alc_spec *spec, const char *pfx,
+ hda_nid_t nid, unsigned int chs)
+{
+ char name[32];
+ sprintf(name, "%s Playback Switch", pfx);
+ return add_control(spec, ALC_CTL_WIDGET_MUTE, name,
+ HDA_COMPOSE_AMP_VAL(nid, chs, 0, HDA_INPUT));
+}
+
+#define alc662_add_stereo_vol(spec, pfx, nid) \
+ alc662_add_vol_ctl(spec, pfx, nid, 3)
+#define alc662_add_stereo_sw(spec, pfx, nid) \
+ alc662_add_sw_ctl(spec, pfx, nid, 3)
+
/* add playback controls from the parsed DAC table */
-static int alc662_auto_create_multi_out_ctls(struct alc_spec *spec,
+static int alc662_auto_create_multi_out_ctls(struct hda_codec *codec,
const struct auto_pin_cfg *cfg)
{
- char name[32];
+ struct alc_spec *spec = codec->spec;
static const char *chname[4] = {
"Front", "Surround", NULL /*CLFE*/, "Side"
};
- hda_nid_t nid;
+ hda_nid_t nid, mix;
int i, err;
for (i = 0; i < cfg->line_outs; i++) {
- if (!spec->multiout.dac_nids[i])
+ nid = spec->multiout.dac_nids[i];
+ if (!nid)
+ continue;
+ mix = alc662_dac_to_mix(codec, cfg->line_out_pins[i], nid);
+ if (!mix)
continue;
- nid = alc880_idx_to_dac(i);
if (i == 2) {
/* Center/LFE */
- err = add_control(spec, ALC_CTL_WIDGET_VOL,
- "Center Playback Volume",
- HDA_COMPOSE_AMP_VAL(nid, 1, 0,
- HDA_OUTPUT));
+ err = alc662_add_vol_ctl(spec, "Center", nid, 1);
if (err < 0)
return err;
- err = add_control(spec, ALC_CTL_WIDGET_VOL,
- "LFE Playback Volume",
- HDA_COMPOSE_AMP_VAL(nid, 2, 0,
- HDA_OUTPUT));
+ err = alc662_add_vol_ctl(spec, "LFE", nid, 2);
if (err < 0)
return err;
- err = add_control(spec, ALC_CTL_WIDGET_MUTE,
- "Center Playback Switch",
- HDA_COMPOSE_AMP_VAL(0x0e, 1, 0,
- HDA_INPUT));
+ err = alc662_add_sw_ctl(spec, "Center", mix, 1);
if (err < 0)
return err;
- err = add_control(spec, ALC_CTL_WIDGET_MUTE,
- "LFE Playback Switch",
- HDA_COMPOSE_AMP_VAL(0x0e, 2, 0,
- HDA_INPUT));
+ err = alc662_add_sw_ctl(spec, "LFE", mix, 2);
if (err < 0)
return err;
} else {
const char *pfx;
if (cfg->line_outs == 1 &&
cfg->line_out_type == AUTO_PIN_SPEAKER_OUT) {
- if (!cfg->hp_pins)
+ if (cfg->hp_outs)
pfx = "Speaker";
else
pfx = "PCM";
} else
pfx = chname[i];
- sprintf(name, "%s Playback Volume", pfx);
- err = add_control(spec, ALC_CTL_WIDGET_VOL, name,
- HDA_COMPOSE_AMP_VAL(nid, 3, 0,
- HDA_OUTPUT));
+ err = alc662_add_vol_ctl(spec, pfx, nid, 3);
if (err < 0)
return err;
if (cfg->line_outs == 1 &&
cfg->line_out_type == AUTO_PIN_SPEAKER_OUT)
pfx = "Speaker";
- sprintf(name, "%s Playback Switch", pfx);
- err = add_control(spec, ALC_CTL_WIDGET_MUTE, name,
- HDA_COMPOSE_AMP_VAL(alc880_idx_to_mixer(i),
- 3, 0, HDA_INPUT));
+ err = alc662_add_sw_ctl(spec, pfx, mix, 3);
if (err < 0)
return err;
}
}
/* add playback controls for speaker and HP outputs */
-static int alc662_auto_create_extra_out(struct alc_spec *spec, hda_nid_t pin,
+/* return DAC nid if any new DAC is assigned */
+static int alc662_auto_create_extra_out(struct hda_codec *codec, hda_nid_t pin,
const char *pfx)
{
- hda_nid_t nid;
+ struct alc_spec *spec = codec->spec;
+ hda_nid_t nid, mix;
int err;
- char name[32];
if (!pin)
return 0;
-
- if (pin == 0x17) {
- /* ALC663 has a mono output pin on 0x17 */
+ nid = alc662_look_for_dac(codec, pin);
+ if (!nid) {
+ char name[32];
+ /* the corresponding DAC is already occupied */
+ if (!(get_wcaps(codec, pin) & AC_WCAP_OUT_AMP))
+ return 0; /* no way */
+ /* create a switch only */
sprintf(name, "%s Playback Switch", pfx);
- err = add_control(spec, ALC_CTL_WIDGET_MUTE, name,
- HDA_COMPOSE_AMP_VAL(pin, 2, 0, HDA_OUTPUT));
- return err;
+ return add_control(spec, ALC_CTL_WIDGET_MUTE, name,
+ HDA_COMPOSE_AMP_VAL(pin, 3, 0, HDA_OUTPUT));
}
- if (alc880_is_fixed_pin(pin)) {
- nid = alc880_idx_to_dac(alc880_fixed_pin_idx(pin));
- /* printk(KERN_DEBUG "DAC nid=%x\n",nid); */
- /* specify the DAC as the extra output */
- if (!spec->multiout.hp_nid)
- spec->multiout.hp_nid = nid;
- else
- spec->multiout.extra_out_nid[0] = nid;
- /* control HP volume/switch on the output mixer amp */
- nid = alc880_idx_to_dac(alc880_fixed_pin_idx(pin));
- sprintf(name, "%s Playback Volume", pfx);
- err = add_control(spec, ALC_CTL_WIDGET_VOL, name,
- HDA_COMPOSE_AMP_VAL(nid, 3, 0, HDA_OUTPUT));
- if (err < 0)
- return err;
- sprintf(name, "%s Playback Switch", pfx);
- err = add_control(spec, ALC_CTL_BIND_MUTE, name,
- HDA_COMPOSE_AMP_VAL(nid, 3, 2, HDA_INPUT));
- if (err < 0)
- return err;
- } else if (alc880_is_multi_pin(pin)) {
- /* set manual connection */
- /* we have only a switch on HP-out PIN */
- sprintf(name, "%s Playback Switch", pfx);
- err = add_control(spec, ALC_CTL_WIDGET_MUTE, name,
- HDA_COMPOSE_AMP_VAL(pin, 3, 0, HDA_OUTPUT));
- if (err < 0)
- return err;
- }
- return 0;
+ mix = alc662_dac_to_mix(codec, pin, nid);
+ if (!mix)
+ return 0;
+ err = alc662_add_vol_ctl(spec, pfx, nid, 3);
+ if (err < 0)
+ return err;
+ err = alc662_add_sw_ctl(spec, pfx, mix, 3);
+ if (err < 0)
+ return err;
+ return nid;
}
/* create playback/capture controls for input pins */
static void alc662_auto_set_output_and_unmute(struct hda_codec *codec,
hda_nid_t nid, int pin_type,
- int dac_idx)
+ hda_nid_t dac)
{
+ int i, num;
+ hda_nid_t srcs[4];
+
alc_set_pin_output(codec, nid, pin_type);
/* need the manual connection? */
- if (alc880_is_multi_pin(nid)) {
- struct alc_spec *spec = codec->spec;
- int idx = alc880_multi_pin_idx(nid);
- snd_hda_codec_write(codec, alc880_idx_to_selector(idx), 0,
- AC_VERB_SET_CONNECT_SEL,
- alc880_dac_to_idx(spec->multiout.dac_nids[dac_idx]));
+ num = snd_hda_get_connections(codec, nid, srcs, ARRAY_SIZE(srcs));
+ if (num <= 1)
+ return;
+ for (i = 0; i < num; i++) {
+ if (alc662_mix_to_dac(srcs[i]) != dac)
+ continue;
+ snd_hda_codec_write(codec, nid, 0, AC_VERB_SET_CONNECT_SEL, i);
+ return;
}
}
static void alc662_auto_init_multi_out(struct hda_codec *codec)
{
struct alc_spec *spec = codec->spec;
+ int pin_type = get_pin_type(spec->autocfg.line_out_type);
int i;
for (i = 0; i <= HDA_SIDE; i++) {
hda_nid_t nid = spec->autocfg.line_out_pins[i];
- int pin_type = get_pin_type(spec->autocfg.line_out_type);
if (nid)
alc662_auto_set_output_and_unmute(codec, nid, pin_type,
- i);
+ spec->multiout.dac_nids[i]);
}
}
hda_nid_t pin;
pin = spec->autocfg.hp_pins[0];
- if (pin) /* connect to front */
- /* use dac 0 */
- alc662_auto_set_output_and_unmute(codec, pin, PIN_HP, 0);
+ if (pin)
+ alc662_auto_set_output_and_unmute(codec, pin, PIN_HP,
+ spec->multiout.hp_nid);
pin = spec->autocfg.speaker_pins[0];
if (pin)
- alc662_auto_set_output_and_unmute(codec, pin, PIN_OUT, 0);
+ alc662_auto_set_output_and_unmute(codec, pin, PIN_OUT,
+ spec->multiout.extra_out_nid[0]);
}
#define ALC662_PIN_CD_NID ALC880_PIN_CD_NID
if (!spec->autocfg.line_outs)
return 0; /* can't find valid BIOS pin config */
- err = alc880_auto_fill_dac_nids(spec, &spec->autocfg);
+ err = alc662_auto_fill_dac_nids(codec, &spec->autocfg);
if (err < 0)
return err;
- err = alc662_auto_create_multi_out_ctls(spec, &spec->autocfg);
+ err = alc662_auto_create_multi_out_ctls(codec, &spec->autocfg);
if (err < 0)
return err;
- err = alc662_auto_create_extra_out(spec,
+ err = alc662_auto_create_extra_out(codec,
spec->autocfg.speaker_pins[0],
"Speaker");
if (err < 0)
return err;
- err = alc662_auto_create_extra_out(spec, spec->autocfg.hp_pins[0],
+ if (err)
+ spec->multiout.extra_out_nid[0] = err;
+ err = alc662_auto_create_extra_out(codec, spec->autocfg.hp_pins[0],
"Headphone");
if (err < 0)
return err;
+ if (err)
+ spec->multiout.hp_nid = err;
err = alc662_auto_create_input_ctls(codec, &spec->autocfg);
if (err < 0)
return err;
struct sigmatel_mic_route {
hda_nid_t pin;
- unsigned char mux_idx;
- unsigned char dmux_idx;
+ signed char mux_idx;
+ signed char dmux_idx;
};
struct sigmatel_spec {
break;
if (i <= AUTO_PIN_FRONT_MIC) {
/* analog pin */
- mic->dmux_idx = 0;
i = get_connection_index(codec, spec->mux_nids[0], pin);
if (i < 0)
return -1;
mic->mux_idx = i;
+ mic->dmux_idx = -1;
+ if (spec->dmux_nids)
+ mic->dmux_idx = get_connection_index(codec,
+ spec->dmux_nids[0],
+ spec->mux_nids[0]);
} else if (spec->dmux_nids) {
/* digital pin */
- mic->mux_idx = 0;
i = get_connection_index(codec, spec->dmux_nids[0], pin);
if (i < 0)
return -1;
mic->dmux_idx = i;
+ mic->mux_idx = -1;
+ if (spec->mux_nids)
+ mic->mux_idx = get_connection_index(codec,
+ spec->mux_nids[0],
+ spec->dmux_nids[0]);
}
return 0;
}
mic = &spec->ext_mic;
else
mic = &spec->int_mic;
- if (mic->dmux_idx)
+ if (mic->dmux_idx >= 0)
snd_hda_codec_write_cache(codec, spec->dmux_nids[0], 0,
AC_VERB_SET_CONNECT_SEL,
mic->dmux_idx);
- else
+ if (mic->mux_idx >= 0)
snd_hda_codec_write_cache(codec, spec->mux_nids[0], 0,
AC_VERB_SET_CONNECT_SEL,
mic->mux_idx);
.name = "Sony S1XP",
.type = AC97_TUNE_INV_EAPD
},
+ {
+ .subvendor = 0x104d,
+ .subdevice = 0x81c0,
+ .name = "Sony VAIO VGN-T350P", /*AD1981B*/
+ .type = AC97_TUNE_INV_EAPD
+ },
+ {
+ .subvendor = 0x104d,
+ .subdevice = 0x81c5,
+ .name = "Sony VAIO VGN-B1VP", /*AD1981B*/
+ .type = AC97_TUNE_INV_EAPD
+ },
{
.subvendor = 0x1043,
.subdevice = 0x80f3,
strlcpy(info.type, "keywest", I2C_NAME_SIZE);
info.addr = keywest_ctx->addr;
keywest_ctx->client = i2c_new_device(adapter, &info);
+ if (!keywest_ctx->client)
+ return -ENODEV;
+ /*
+ * We know the driver is already loaded, so the device should be
+ * already bound. If not it means binding failed, and then there
+ * is no point in keeping the device instantiated.
+ */
+ if (!keywest_ctx->client->driver) {
+ i2c_unregister_device(keywest_ctx->client);
+ keywest_ctx->client = NULL;
+ return -ENODEV;
+ }
/*
* Let i2c-core delete that device on driver removal.
{ }
};
-struct i2c_driver keywest_driver = {
+static struct i2c_driver keywest_driver = {
.driver = {
.name = "PMac Keywest Audio",
},
mode (supports single stereo In/Out).
You will also need to select the audio interfaces to support below.
-config SND_BF5XX_TDM
- tristate "SoC I2S(TDM mode) Audio for the ADI BF5xx chip"
- depends on (BLACKFIN && SND_SOC)
- help
- Say Y or M if you want to add support for codecs attached to
- the Blackfin SPORT (synchronous serial ports) interface in TDM
- mode.
- You will also need to select the audio interfaces to support below.
-
config SND_BF5XX_SOC_SSM2602
tristate "SoC SSM2602 Audio support for BF52x ezkit"
depends on SND_BF5XX_I2S
Enter the GPIO used to control AD73311's SE pin. Acceptable
values are 0 to 7
+config SND_BF5XX_TDM
+ tristate "SoC I2S(TDM mode) Audio for the ADI BF5xx chip"
+ depends on (BLACKFIN && SND_SOC)
+ help
+ Say Y or M if you want to add support for codecs attached to
+ the Blackfin SPORT (synchronous serial ports) interface in TDM
+ mode.
+ You will also need to select the audio interfaces to support below.
+
+config SND_BF5XX_SOC_AD1836
+ tristate "SoC AD1836 Audio support for BF5xx"
+ depends on SND_BF5XX_TDM
+ select SND_BF5XX_SOC_TDM
+ select SND_SOC_AD1836
+ help
+ Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
+
+config SND_BF5XX_SOC_AD1938
+ tristate "SoC AD1938 Audio support for Blackfin"
+ depends on SND_BF5XX_TDM
+ select SND_BF5XX_SOC_TDM
+ select SND_SOC_AD1938
+ help
+ Say Y if you want to add support for AD1938 codec on Blackfin.
+
config SND_BF5XX_AC97
tristate "SoC AC97 Audio for the ADI BF5xx chip"
depends on BLACKFIN
Say y if you want AC97 driver to support up to 5.1 channel audio.
this mode will consume much more memory for DMA.
+config SND_BF5XX_HAVE_COLD_RESET
+ bool "BOARD has COLD Reset GPIO"
+ depends on SND_BF5XX_AC97
+ default y if BFIN548_EZKIT
+ default n if !BFIN548_EZKIT
+
+config SND_BF5XX_RESET_GPIO_NUM
+ int "Set a GPIO for cold reset"
+ depends on SND_BF5XX_HAVE_COLD_RESET
+ range 0 159
+ default 19 if BFIN548_EZKIT
+ default 5 if BFIN537_STAMP
+ default 0
+ help
+ Set the correct GPIO for RESET the sound chip.
+
+config SND_BF5XX_SOC_AD1980
+ tristate "SoC AD1980/1 Audio support for BF5xx"
+ depends on SND_BF5XX_AC97
+ select SND_BF5XX_SOC_AC97
+ select SND_SOC_AD1980
+ help
+ Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
+
config SND_BF5XX_SOC_SPORT
tristate
select SND_SOC_AC97_BUS
select SND_BF5XX_SOC_SPORT
-config SND_BF5XX_SOC_AD1836
- tristate "SoC AD1836 Audio support for BF5xx"
- depends on SND_BF5XX_TDM
- select SND_BF5XX_SOC_TDM
- select SND_SOC_AD1836
- help
- Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
-
-config SND_BF5XX_SOC_AD1980
- tristate "SoC AD1980/1 Audio support for BF5xx"
- depends on SND_BF5XX_AC97
- select SND_BF5XX_SOC_AC97
- select SND_SOC_AD1980
- help
- Say Y if you want to add support for SoC audio on BF5xx STAMP/EZKIT.
-
-config SND_BF5XX_SOC_AD1938
- tristate "SoC AD1938 Audio support for Blackfin"
- depends on SND_BF5XX_TDM
- select SND_BF5XX_SOC_TDM
- select SND_SOC_AD1938
- help
- Say Y if you want to add support for AD1938 codec on Blackfin.
-
config SND_BF5XX_SPORT_NUM
int "Set a SPORT for Sound chip"
depends on (SND_BF5XX_I2S || SND_BF5XX_AC97 || SND_BF5XX_TDM)
default 0
help
Set the correct SPORT for sound chip.
-
-config SND_BF5XX_HAVE_COLD_RESET
- bool "BOARD has COLD Reset GPIO"
- depends on SND_BF5XX_AC97
- default y if BFIN548_EZKIT
- default n if !BFIN548_EZKIT
-
-config SND_BF5XX_RESET_GPIO_NUM
- int "Set a GPIO for cold reset"
- depends on SND_BF5XX_HAVE_COLD_RESET
- range 0 159
- default 19 if BFIN548_EZKIT
- default 5 if BFIN537_STAMP
- default 0
- help
- Set the correct GPIO for RESET the sound chip.
* TFS. When Port G is selected and EMAC then there is a conflict between
* the PHY interrupt line and TFS. Current settings prevent the conflict
* by ignoring the TFS pin when Port G is selected. This allows both
- * ssm2602 using Port G and EMAC concurrently.
+ * codecs and EMAC using Port G concurrently.
*/
-#ifdef CONFIG_BF527_SPORT0_PORTF
-#define LOCAL_SPORT0_TFS (P_SPORT0_TFS)
-#else
+#ifdef CONFIG_BF527_SPORT0_PORTG
#define LOCAL_SPORT0_TFS (0)
+#else
+#define LOCAL_SPORT0_TFS (P_SPORT0_TFS)
#endif
static u16 sport_req[][7] = { {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
* TFS. When Port G is selected and EMAC then there is a conflict between
* the PHY interrupt line and TFS. Current settings prevent the conflict
* by ignoring the TFS pin when Port G is selected. This allows both
- * ssm2602 using Port G and EMAC concurrently.
+ * codecs and EMAC using Port G concurrently.
*/
-#ifdef CONFIG_BF527_SPORT0_PORTF
-#define LOCAL_SPORT0_TFS (P_SPORT0_TFS)
-#else
+#ifdef CONFIG_BF527_SPORT0_PORTG
#define LOCAL_SPORT0_TFS (0)
+#else
+#define LOCAL_SPORT0_TFS (P_SPORT0_TFS)
#endif
static u16 sport_req[][7] = { {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
DAVINCI_MCBSP_WORD_32,
};
-static struct davinci_pcm_dma_params davinci_i2s_pcm_out = {
- .name = "I2S PCM Stereo out",
-};
-
-static struct davinci_pcm_dma_params davinci_i2s_pcm_in = {
- .name = "I2S PCM Stereo in",
-};
-
struct davinci_mcbsp_dev {
+ /*
+ * dma_params must be first because rtd->dai->cpu_dai->private_data
+ * is cast to a pointer of an array of struct davinci_pcm_dma_params in
+ * davinci_pcm_open.
+ */
+ struct davinci_pcm_dma_params dma_params[2];
void __iomem *base;
#define MOD_DSP_A 0
#define MOD_DSP_B 1
int mode;
u32 pcr;
struct clk *clk;
- struct davinci_pcm_dma_params *dma_params[2];
};
static inline void davinci_mcbsp_write_reg(struct davinci_mcbsp_dev *dev,
toggle_clock(dev, playback);
}
-static int davinci_i2s_startup(struct snd_pcm_substream *substream,
- struct snd_soc_dai *cpu_dai)
-{
- struct davinci_mcbsp_dev *dev = cpu_dai->private_data;
- cpu_dai->dma_data = dev->dma_params[substream->stream];
- return 0;
-}
-
#define DEFAULT_BITPERSAMPLE 16
static int davinci_i2s_set_dai_fmt(struct snd_soc_dai *cpu_dai,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
- struct davinci_pcm_dma_params *dma_params = dai->dma_data;
struct davinci_mcbsp_dev *dev = dai->private_data;
+ struct davinci_pcm_dma_params *dma_params =
+ &dev->dma_params[substream->stream];
struct snd_interval *i = NULL;
int mcbsp_word_length;
unsigned int rcr, xcr, srgr;
#define DAVINCI_I2S_RATES SNDRV_PCM_RATE_8000_96000
static struct snd_soc_dai_ops davinci_i2s_dai_ops = {
- .startup = davinci_i2s_startup,
.shutdown = davinci_i2s_shutdown,
.prepare = davinci_i2s_prepare,
.trigger = davinci_i2s_trigger,
dev->base = (void __iomem *)IO_ADDRESS(mem->start);
- dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK] = &davinci_i2s_pcm_out;
- dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK]->dma_addr =
+ dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK].dma_addr =
(dma_addr_t)(io_v2p(dev->base) + DAVINCI_MCBSP_DXR_REG);
- dev->dma_params[SNDRV_PCM_STREAM_CAPTURE] = &davinci_i2s_pcm_in;
- dev->dma_params[SNDRV_PCM_STREAM_CAPTURE]->dma_addr =
+ dev->dma_params[SNDRV_PCM_STREAM_CAPTURE].dma_addr =
(dma_addr_t)(io_v2p(dev->base) + DAVINCI_MCBSP_DRR_REG);
/* first TX, then RX */
ret = -ENXIO;
goto err_free_mem;
}
- dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK]->channel = res->start;
+ dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK].channel = res->start;
res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
if (!res) {
ret = -ENXIO;
goto err_free_mem;
}
- dev->dma_params[SNDRV_PCM_STREAM_CAPTURE]->channel = res->start;
+ dev->dma_params[SNDRV_PCM_STREAM_CAPTURE].channel = res->start;
davinci_i2s_dai.private_data = dev;
ret = snd_soc_register_dai(&davinci_i2s_dai);
printk(KERN_ERR "GBLCTL write error\n");
}
-static int davinci_mcasp_startup(struct snd_pcm_substream *substream,
- struct snd_soc_dai *cpu_dai)
-{
- struct davinci_audio_dev *dev = cpu_dai->private_data;
- cpu_dai->dma_data = dev->dma_params[substream->stream];
- return 0;
-}
-
static void mcasp_start_rx(struct davinci_audio_dev *dev)
{
mcasp_set_ctl_reg(dev->base + DAVINCI_MCASP_GBLCTLR_REG, RXHCLKRST);
static void davinci_mcasp_start(struct davinci_audio_dev *dev, int stream)
{
- if (stream == SNDRV_PCM_STREAM_PLAYBACK)
+ if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ if (dev->txnumevt) /* enable FIFO */
+ mcasp_set_bits(dev->base + DAVINCI_MCASP_WFIFOCTL,
+ FIFO_ENABLE);
mcasp_start_tx(dev);
- else
+ } else {
+ if (dev->rxnumevt) /* enable FIFO */
+ mcasp_set_bits(dev->base + DAVINCI_MCASP_RFIFOCTL,
+ FIFO_ENABLE);
mcasp_start_rx(dev);
-
- /* enable FIFO */
- if (dev->txnumevt)
- mcasp_set_bits(dev->base + DAVINCI_MCASP_WFIFOCTL, FIFO_ENABLE);
-
- if (dev->rxnumevt)
- mcasp_set_bits(dev->base + DAVINCI_MCASP_RFIFOCTL, FIFO_ENABLE);
+ }
}
static void mcasp_stop_rx(struct davinci_audio_dev *dev)
static void davinci_mcasp_stop(struct davinci_audio_dev *dev, int stream)
{
- if (stream == SNDRV_PCM_STREAM_PLAYBACK)
+ if (stream == SNDRV_PCM_STREAM_PLAYBACK) {
+ if (dev->txnumevt) /* disable FIFO */
+ mcasp_clr_bits(dev->base + DAVINCI_MCASP_WFIFOCTL,
+ FIFO_ENABLE);
mcasp_stop_tx(dev);
- else
+ } else {
+ if (dev->rxnumevt) /* disable FIFO */
+ mcasp_clr_bits(dev->base + DAVINCI_MCASP_RFIFOCTL,
+ FIFO_ENABLE);
mcasp_stop_rx(dev);
-
- /* disable FIFO */
- if (dev->txnumevt)
- mcasp_clr_bits(dev->base + DAVINCI_MCASP_WFIFOCTL, FIFO_ENABLE);
-
- if (dev->rxnumevt)
- mcasp_clr_bits(dev->base + DAVINCI_MCASP_RFIFOCTL, FIFO_ENABLE);
+ }
}
static int davinci_mcasp_set_dai_fmt(struct snd_soc_dai *cpu_dai,
{
struct davinci_audio_dev *dev = cpu_dai->private_data;
struct davinci_pcm_dma_params *dma_params =
- dev->dma_params[substream->stream];
+ &dev->dma_params[substream->stream];
int word_length;
u8 numevt;
}
static struct snd_soc_dai_ops davinci_mcasp_dai_ops = {
- .startup = davinci_mcasp_startup,
.trigger = davinci_mcasp_trigger,
.hw_params = davinci_mcasp_hw_params,
.set_fmt = davinci_mcasp_set_dai_fmt,
struct resource *mem, *ioarea, *res;
struct snd_platform_data *pdata;
struct davinci_audio_dev *dev;
- int count = 0;
int ret = 0;
dev = kzalloc(sizeof(struct davinci_audio_dev), GFP_KERNEL);
if (!dev)
return -ENOMEM;
- dma_data = kzalloc(sizeof(struct davinci_pcm_dma_params) * 2,
- GFP_KERNEL);
- if (!dma_data) {
- ret = -ENOMEM;
- goto err_release_dev;
- }
-
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!mem) {
dev_err(&pdev->dev, "no mem resource?\n");
dev->txnumevt = pdata->txnumevt;
dev->rxnumevt = pdata->rxnumevt;
- dma_data[count].name = "I2S PCM Stereo out";
- dma_data[count].eventq_no = pdata->eventq_no;
- dma_data[count].dma_addr = (dma_addr_t) (pdata->tx_dma_offset +
+ dma_data = &dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK];
+ dma_data->eventq_no = pdata->eventq_no;
+ dma_data->dma_addr = (dma_addr_t) (pdata->tx_dma_offset +
io_v2p(dev->base));
- dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK] = &dma_data[count];
/* first TX, then RX */
res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
goto err_release_region;
}
- dma_data[count].channel = res->start;
- count++;
- dma_data[count].name = "I2S PCM Stereo in";
- dma_data[count].eventq_no = pdata->eventq_no;
- dma_data[count].dma_addr = (dma_addr_t)(pdata->rx_dma_offset +
+ dma_data->channel = res->start;
+
+ dma_data = &dev->dma_params[SNDRV_PCM_STREAM_CAPTURE];
+ dma_data->eventq_no = pdata->eventq_no;
+ dma_data->dma_addr = (dma_addr_t)(pdata->rx_dma_offset +
io_v2p(dev->base));
- dev->dma_params[SNDRV_PCM_STREAM_CAPTURE] = &dma_data[count];
res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
if (!res) {
goto err_release_region;
}
- dma_data[count].channel = res->start;
+ dma_data->channel = res->start;
davinci_mcasp_dai[pdata->op_mode].private_data = dev;
davinci_mcasp_dai[pdata->op_mode].dev = &pdev->dev;
ret = snd_soc_register_dai(&davinci_mcasp_dai[pdata->op_mode]);
err_release_region:
release_mem_region(mem->start, (mem->end - mem->start) + 1);
err_release_data:
- kfree(dma_data);
-err_release_dev:
kfree(dev);
return ret;
static int davinci_mcasp_remove(struct platform_device *pdev)
{
struct snd_platform_data *pdata = pdev->dev.platform_data;
- struct davinci_pcm_dma_params *dma_data;
struct davinci_audio_dev *dev;
struct resource *mem;
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
release_mem_region(mem->start, (mem->end - mem->start) + 1);
- dma_data = dev->dma_params[SNDRV_PCM_STREAM_PLAYBACK];
- kfree(dma_data);
kfree(dev);
return 0;
};
struct davinci_audio_dev {
+ /*
+ * dma_params must be first because rtd->dai->cpu_dai->private_data
+ * is cast to a pointer of an array of struct davinci_pcm_dma_params in
+ * davinci_pcm_open.
+ */
+ struct davinci_pcm_dma_params dma_params[2];
void __iomem *base;
int sample_rate;
struct clk *clk;
- struct davinci_pcm_dma_params *dma_params[2];
unsigned int codec_fmt;
/* McASP specific data */
static int davinci_pcm_dma_request(struct snd_pcm_substream *substream)
{
struct davinci_runtime_data *prtd = substream->runtime->private_data;
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct davinci_pcm_dma_params *dma_data = rtd->dai->cpu_dai->dma_data;
struct edmacc_param p_ram;
int ret;
- if (!dma_data)
- return -ENODEV;
-
- prtd->params = dma_data;
-
/* Request master DMA channel */
ret = edma_alloc_channel(prtd->params->channel,
davinci_pcm_dma_irq, substream,
struct snd_pcm_runtime *runtime = substream->runtime;
struct davinci_runtime_data *prtd;
int ret = 0;
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct davinci_pcm_dma_params *pa = rtd->dai->cpu_dai->private_data;
+ struct davinci_pcm_dma_params *params = &pa[substream->stream];
+ if (!params)
+ return -ENODEV;
snd_soc_set_runtime_hwparams(substream, &davinci_pcm_hardware);
/* ensure that buffer size is a multiple of period size */
return -ENOMEM;
spin_lock_init(&prtd->lock);
+ prtd->params = params;
runtime->private_data = prtd;
struct davinci_pcm_dma_params {
- char *name; /* stream identifier */
int channel; /* sync dma channel ID */
unsigned short acnt;
dma_addr_t dma_addr; /* device physical address for DMA */
config SND_PXA2XX_SOC_IMOTE2
tristate "SoC Audio support for IMote 2"
- depends on SND_PXA2XX_SOC && MACH_INTELMOTE2
+ depends on SND_PXA2XX_SOC && MACH_INTELMOTE2 && I2C
select SND_PXA2XX_SOC_I2S
select SND_SOC_WM8940
help
* build a feature control
*/
+static size_t append_ctl_name(struct snd_kcontrol *kctl, const char *str)
+{
+ return strlcat(kctl->id.name, str, sizeof(kctl->id.name));
+}
+
static void build_feature_ctl(struct mixer_build *state, unsigned char *desc,
unsigned int ctl_mask, int control,
struct usb_audio_term *iterm, int unitid)
*/
if (! mapped_name && ! (state->oterm.type >> 16)) {
if ((state->oterm.type & 0xff00) == 0x0100) {
- len = strlcat(kctl->id.name, " Capture", sizeof(kctl->id.name));
+ len = append_ctl_name(kctl, " Capture");
} else {
- len = strlcat(kctl->id.name + len, " Playback", sizeof(kctl->id.name));
+ len = append_ctl_name(kctl, " Playback");
}
}
- strlcat(kctl->id.name + len, control == USB_FEATURE_MUTE ? " Switch" : " Volume",
- sizeof(kctl->id.name));
+ append_ctl_name(kctl, control == USB_FEATURE_MUTE ?
+ " Switch" : " Volume");
if (control == USB_FEATURE_VOLUME) {
kctl->tlv.c = mixer_vol_tlv;
kctl->vd[0].access |=
len = get_term_name(state, iterm, kctl->id.name, sizeof(kctl->id.name), 0);
if (! len)
len = sprintf(kctl->id.name, "Mixer Source %d", in_ch + 1);
- strlcat(kctl->id.name + len, " Volume", sizeof(kctl->id.name));
+ append_ctl_name(kctl, " Volume");
snd_printdd(KERN_INFO "[%d] MU [%s] ch = %d, val = %d/%d\n",
cval->id, kctl->id.name, cval->channels, cval->min, cval->max);
if (! len)
strlcpy(kctl->id.name, name, sizeof(kctl->id.name));
}
- strlcat(kctl->id.name, " ", sizeof(kctl->id.name));
- strlcat(kctl->id.name, valinfo->suffix, sizeof(kctl->id.name));
+ append_ctl_name(kctl, " ");
+ append_ctl_name(kctl, valinfo->suffix);
snd_printdd(KERN_INFO "[%d] PU [%s] ch = %d, val = %d/%d\n",
cval->id, kctl->id.name, cval->channels, cval->min, cval->max);
strlcpy(kctl->id.name, "USB", sizeof(kctl->id.name));
if ((state->oterm.type & 0xff00) == 0x0100)
- strlcat(kctl->id.name, " Capture Source", sizeof(kctl->id.name));
+ append_ctl_name(kctl, " Capture Source");
else
- strlcat(kctl->id.name, " Playback Source", sizeof(kctl->id.name));
+ append_ctl_name(kctl, " Playback Source");
}
snd_printdd(KERN_INFO "[%d] SU [%s] items = %d\n",
snd_printdd(KERN_DEBUG "%i\n", atomic_read(&us122l->mmap_count));
}
-static struct vm_operations_struct usb_stream_hwdep_vm_ops = {
+static const struct vm_operations_struct usb_stream_hwdep_vm_ops = {
.open = usb_stream_hwdep_vm_open,
.fault = usb_stream_hwdep_vm_fault,
.close = usb_stream_hwdep_vm_close,
return 0;
}
-static struct vm_operations_struct us428ctls_vm_ops = {
+static const struct vm_operations_struct us428ctls_vm_ops = {
.fault = snd_us428ctls_vm_fault,
};
}
-static struct vm_operations_struct snd_usX2Y_hwdep_pcm_vm_ops = {
+static const struct vm_operations_struct snd_usX2Y_hwdep_pcm_vm_ops = {
.open = snd_usX2Y_hwdep_pcm_vm_open,
.close = snd_usX2Y_hwdep_pcm_vm_close,
.fault = snd_usX2Y_hwdep_pcm_vm_fault,
perf-top
perf*.1
perf*.xml
+perf*.html
common-cmds.h
tags
TAGS
static void abs_printout(int counter, double avg)
{
+ double total, ratio = 0.0;
+
fprintf(stderr, " %14.0f %-24s", avg, event_name(counter));
if (MATCH_EVENT(HARDWARE, HW_INSTRUCTIONS, counter)) {
- fprintf(stderr, " # %10.3f IPC ",
- avg / avg_stats(&runtime_cycles_stats));
+ total = avg_stats(&runtime_cycles_stats);
+
+ if (total)
+ ratio = avg / total;
+
+ fprintf(stderr, " # %10.3f IPC ", ratio);
} else {
- fprintf(stderr, " # %10.3f M/sec",
- 1000.0 * avg / avg_stats(&runtime_nsecs_stats));
+ total = avg_stats(&runtime_nsecs_stats);
+
+ if (total)
+ ratio = 1000.0 * avg / total;
+
+ fprintf(stderr, " # %10.3f M/sec", ratio);
}
}
#include "module.h"
#include <libelf.h>
+#include <libgen.h>
#include <gelf.h>
#include <elf.h>
#include <dirent.h>
static int mod_dso__load_module_paths(struct mod_dso *self)
{
struct utsname uts;
- int count = 0, len;
+ int count = 0, len, err = -1;
char *line = NULL;
FILE *file;
- char *path;
+ char *dpath, *dir;
size_t n;
if (uname(&uts) < 0)
- goto out_failure;
+ return err;
len = strlen("/lib/modules/");
len += strlen(uts.release);
len += strlen("/modules.dep");
- path = calloc(1, len);
- if (path == NULL)
- goto out_failure;
+ dpath = calloc(1, len + 1);
+ if (dpath == NULL)
+ return err;
- strcat(path, "/lib/modules/");
- strcat(path, uts.release);
- strcat(path, "/modules.dep");
+ strcat(dpath, "/lib/modules/");
+ strcat(dpath, uts.release);
+ strcat(dpath, "/modules.dep");
- file = fopen(path, "r");
- free(path);
+ file = fopen(dpath, "r");
if (file == NULL)
goto out_failure;
+ dir = dirname(dpath);
+ if (!dir)
+ goto out_failure;
+ strcat(dir, "/");
+
while (!feof(file)) {
- char *name, *tmp;
struct module *module;
+ char *name, *path, *tmp;
+ FILE *modfile;
int line_len;
line_len = getline(&line, &n, file);
break;
if (!line)
- goto out_failure;
+ break;
line[--line_len] = '\0'; /* \n */
- path = strtok(line, ":");
+ path = strchr(line, ':');
+ if (!path)
+ break;
+ *path = '\0';
+
+ path = strdup(line);
if (!path)
- goto out_failure;
+ break;
+
+ if (!strstr(path, dir)) {
+ if (strncmp(path, "kernel/", 7))
+ break;
+
+ free(path);
+ path = calloc(1, strlen(dir) + strlen(line) + 1);
+ if (!path)
+ break;
+ strcat(path, dir);
+ strcat(path, line);
+ }
+
+ modfile = fopen(path, "r");
+ if (modfile == NULL)
+ break;
+ fclose(modfile);
name = strdup(path);
- name = strtok(name, "/");
+ if (!name)
+ break;
+ name = strtok(name, "/");
tmp = name;
while (tmp) {
if (tmp)
name = tmp;
}
+
name = strsep(&name, ".");
+ if (!name)
+ break;
- /* Quirk: replace '-' with '_' in sound modules */
+ /* Quirk: replace '-' with '_' in all modules */
for (len = strlen(name); len; len--) {
if (*(name+len) == '-')
*(name+len) = '_';
}
module = module__new(name, path);
- if (!module) {
- fprintf(stderr, "load_module_paths: allocation error\n");
- goto out_failure;
- }
+ if (!module)
+ break;
mod_dso__insert_module(self, module);
module->sections = sec_dso__new_dso("sections");
- if (!module->sections) {
- fprintf(stderr, "load_module_paths: allocation error\n");
- goto out_failure;
- }
+ if (!module->sections)
+ break;
module->active = mod_dso__load_sections(module);
count++;
}
- free(line);
- fclose(file);
-
- return count;
+ if (feof(file))
+ err = count;
+ else
+ fprintf(stderr, "load_module_paths: modules.dep parsing failure!\n");
out_failure:
- return -1;
+ if (dpath)
+ free(dpath);
+ if (file)
+ fclose(file);
+ if (line)
+ free(line);
+
+ return err;
}
int mod_dso__load_modules(struct mod_dso *dso)
DIR *sys_dir, *evt_dir;
struct dirent *sys_next, *evt_next, sys_dirent, evt_dirent;
char id_buf[4];
- int sys_dir_fd, fd;
+ int fd;
u64 id;
char evt_path[MAXPATHLEN];
+ char dir_path[MAXPATHLEN];
if (valid_debugfs_mount(debugfs_path))
return NULL;
sys_dir = opendir(debugfs_path);
if (!sys_dir)
- goto cleanup;
- sys_dir_fd = dirfd(sys_dir);
+ return NULL;
for_each_subsystem(sys_dir, sys_dirent, sys_next) {
- int dfd = openat(sys_dir_fd, sys_dirent.d_name,
- O_RDONLY|O_DIRECTORY), evt_dir_fd;
- if (dfd == -1)
- continue;
- evt_dir = fdopendir(dfd);
- if (!evt_dir) {
- close(dfd);
+
+ snprintf(dir_path, MAXPATHLEN, "%s/%s", debugfs_path,
+ sys_dirent.d_name);
+ evt_dir = opendir(dir_path);
+ if (!evt_dir)
continue;
- }
- evt_dir_fd = dirfd(evt_dir);
+
for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next) {
- snprintf(evt_path, MAXPATHLEN, "%s/id",
+
+ snprintf(evt_path, MAXPATHLEN, "%s/%s/id", dir_path,
evt_dirent.d_name);
- fd = openat(evt_dir_fd, evt_path, O_RDONLY);
+ fd = open(evt_path, O_RDONLY);
if (fd < 0)
continue;
if (read(fd, id_buf, sizeof(id_buf)) < 0) {
closedir(evt_dir);
}
-cleanup:
closedir(sys_dir);
return NULL;
}
{
DIR *sys_dir, *evt_dir;
struct dirent *sys_next, *evt_next, sys_dirent, evt_dirent;
- int sys_dir_fd;
char evt_path[MAXPATHLEN];
+ char dir_path[MAXPATHLEN];
if (valid_debugfs_mount(debugfs_path))
return;
sys_dir = opendir(debugfs_path);
if (!sys_dir)
- goto cleanup;
- sys_dir_fd = dirfd(sys_dir);
+ return;
for_each_subsystem(sys_dir, sys_dirent, sys_next) {
- int dfd = openat(sys_dir_fd, sys_dirent.d_name,
- O_RDONLY|O_DIRECTORY), evt_dir_fd;
- if (dfd == -1)
- continue;
- evt_dir = fdopendir(dfd);
- if (!evt_dir) {
- close(dfd);
+
+ snprintf(dir_path, MAXPATHLEN, "%s/%s", debugfs_path,
+ sys_dirent.d_name);
+ evt_dir = opendir(dir_path);
+ if (!evt_dir)
continue;
- }
- evt_dir_fd = dirfd(evt_dir);
+
for_each_event(sys_dirent, evt_dir, evt_dirent, evt_next) {
snprintf(evt_path, MAXPATHLEN, "%s:%s",
sys_dirent.d_name, evt_dirent.d_name);
}
closedir(evt_dir);
}
-
-cleanup:
closedir(sys_dir);
}
struct mod_dso *mods = mod_dso__new_dso("modules");
struct module *pos;
struct rb_node *next;
- int err;
+ int err, count = 0;
err = mod_dso__load_modules(mods);
break;
next = rb_next(&pos->rb_node);
+ count += err;
}
if (err < 0) {
mod_dso__delete_modules(mods);
mod_dso__delete_self(mods);
+ return err;
}
- return err;
+ return count;
}
static inline void dso__fill_symbol_holes(struct dso *self)
if (vmlinux) {
err = dso__load_vmlinux(self, vmlinux, filter, v);
- if (err > 0 && use_modules)
- err = dso__load_modules(self, filter, v);
+ if (err > 0 && use_modules) {
+ int syms = dso__load_modules(self, filter, v);
+
+ if (syms < 0) {
+ fprintf(stderr, "dso__load_modules failed!\n");
+ return syms;
+ }
+ err += syms;
+ }
}
if (err <= 0)
return 0;
}
-static struct vm_operations_struct kvm_vcpu_vm_ops = {
+static const struct vm_operations_struct kvm_vcpu_vm_ops = {
.fault = kvm_vcpu_fault,
};
return 0;
}
-static struct vm_operations_struct kvm_vm_vm_ops = {
+static const struct vm_operations_struct kvm_vm_vm_ops = {
.fault = kvm_vm_fault,
};
DEFINE_SIMPLE_ATTRIBUTE(vcpu_stat_fops, vcpu_stat_get, NULL, "%llu\n");
-static struct file_operations *stat_fops[] = {
+static const struct file_operations *stat_fops[] = {
[KVM_STAT_VCPU] = &vcpu_stat_fops,
[KVM_STAT_VM] = &vm_stat_fops,
};
projects / linux-2.6-block.git / commitdiff