Merge tag 'printk-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/printk...

Pull printk updates from Petr Mladek:
 "This is the "last" part of the support for the new nbcon consoles.
  Where "nbcon" stays for "No Big console lock CONsoles" aka not under
  the console_lock.

  New callbacks are added to struct console:

   - write_thread() for flushing nbcon consoles in task context.

   - write_atomic() for flushing nbcon consoles in atomic context,
     including NMI.

   - con->device_lock() and device_unlock() for taking the driver
     specific lock, for example, port->lock.

  New printk-specific kthreads are created:

   - per-console kthreads which get responsible for flushing normal
     priority messages on nbcon consoles.

   - thread which gets responsible for flushing normal priority messages
     on all consoles when CONFIG_RT enabled.

  The new callbacks are called under a special per-console lock which
  has already been added back in v6.7. It allows to distinguish three
  severities: normal, emergency, and panic. A context with a higher
  priority could take over the ownership when it is safe even in the
  middle of handling a record. The panic context could do it even when
  it is not safe. But it is allowed only for the final desperate flush
  before entering the infinite loop.

  The new lock helps to flush the messages directly in emergency and
  panic contexts. But it is not enough in all situations:

   - console_lock() is still need for synchronization against boot
     consoles.

   - con->device_lock() is need for synchronization against other
     operations on the same HW, e.g. serial port speed setting,
     non-printk related read/write.

  The dependency on con->device_lock() is mutual. Any code taking the
  driver specific lock has to acquire the related nbcon console context
  as well. For example, see the new uart_port_lock() API. It provides
  the necessary synchronization against emergency and panic contexts
  where the messages are flushed only under the new per-console lock.

  Maybe surprisingly, a quite tricky part is the decision how to flush
  the consoles in various situations. It has to take into account:

   - message priority:    normal, emergency, panic

   - scheduling context:  task, atomic, deferred_legacy

   - registered consoles: boot, legacy, nbcon

   - threads are running: early boot, suspend, shutdown, panic

   - caller:              printk(), pr_flush(), printk_flush_in_panic(),
                          console_unlock(), console_start(), ...

  The primary decision is made in printk_get_console_flush_type(). It
  creates a hint what the caller should do:

   - flush nbcon consoles directly or via the kthread

   - call the legacy loop (console_unlock()) directly or via irq_work

  The existing behavior is preserved for the legacy consoles. The only
  exception is that they are not longer flushed directly from printk()
  in panic() before CPUs are stopped. But this blocking happens only
  when at least one nbcon console is registered. The motivation is to
  increase a chance to produce the crash dump. They legacy consoles
  might create a deadlock in compare with nbcon consoles. The nbcon
  console should allow to see the messages even when the crash dump
  fails.

  There are three possible ways how nbcon consoles are flushed:

   - The per-nbcon-console kthread is responsible for flushing messages
     added with the normal priority. This is the default mode.

   - The legacy loop, aka console_unlock(), is used when there is still
     a boot console registered. There is no easy way how to match an
     early console driver with a nbcon console driver. And the
     console_lock() provides the only reliable serialization at the
     moment.

     The legacy loop uses either con->write_atomic() or
     con->write_thread() callbacks depending on whether it is allowed to
     schedule. The atomic variant has to be used from printk().

   - In other situations, the messages are flushed directly using
     write_atomic() which can be called in any context, including NMI.
     It is primary needed during early boot or shutdown, in emergency
     situations, and panic.

  The emergency priority is used by a code called within
  nbcon_cpu_emergency_enter()/exit(). At the moment, it is used in four
  situations: WARN(), Oops, lockdep, and RCU stall reports.

  Finally, there is no nbcon console at the moment. It means that the
  changes should _not_ modify the existing behavior. The only exception
  is CONFIG_RT which would force offloading the legacy loop, for normal
  priority context, into the dedicated kthread"

* tag 'printk-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (54 commits)
  printk: Avoid false positive lockdep report for legacy printing
  printk: nbcon: Assign nice -20 for printing threads
  printk: Implement legacy printer kthread for PREEMPT_RT
  tty: sysfs: Add nbcon support for 'active'
  proc: Add nbcon support for /proc/consoles
  proc: consoles: Add notation to c_start/c_stop
  printk: nbcon: Show replay message on takeover
  printk: Provide helper for message prepending
  printk: nbcon: Rely on kthreads for normal operation
  printk: nbcon: Use thread callback if in task context for legacy
  printk: nbcon: Relocate nbcon_atomic_emit_one()
  printk: nbcon: Introduce printer kthreads
  printk: nbcon: Init @nbcon_seq to highest possible
  printk: nbcon: Add context to usable() and emit()
  printk: Flush console on unregister_console()
  printk: Fail pr_flush() if before SYSTEM_SCHEDULING
  printk: nbcon: Add function for printers to reacquire ownership
  printk: nbcon: Use raw_cpu_ptr() instead of open coding
  printk: Use the BITS_PER_LONG macro
  lockdep: Mark emergency sections in lockdep splats
  ...

diff --cc drivers/tty/tty_io.c
Simple merge

diff --cc kernel/printk/printk.c
Simple merge