The device tree documentation for the keystone machines are located at
Documentation/devicetree/bindings/arm/keystone/keystone.txt
-Known issues & workaround
--------------------------
-
-Some of the device drivers used on keystone are re-used from that from
-DaVinci and other TI SoCs. These device drivers may use clock APIs directly.
-Some of the keystone specific drivers such as netcp uses run time power
-management API instead to enable clock. As this API has limitations on
-keystone, following workaround is needed to boot Linux.
-
- Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise
- clock frameworks will try to disable clocks that are unused and disable
- the hardware. This is because netcp related power domain and clock
- domains are enabled in u-boot as run time power management API currently
- doesn't enable clocks for netcp due to a limitation. This workaround is
- expected to be removed in the future when proper API support becomes
- available. Until then, this work around is needed.
-
-
Document Author
---------------
Murali Karicheri <m-karicheri2@ti.com>
F: drivers/i2c/busses/i2c-at91.c
ATMEL ISI DRIVER
-M: Josh Wu <josh.wu@atmel.com>
+M: Ludovic Desroches <ludovic.desroches@atmel.com>
L: linux-media@vger.kernel.org
S: Supported
F: drivers/media/platform/soc_camera/atmel-isi.c
F: drivers/net/ethernet/cadence/
ATMEL NAND DRIVER
-M: Josh Wu <josh.wu@atmel.com>
+M: Wenyou Yang <wenyou.yang@atmel.com>
+M: Josh Wu <rainyfeeling@outlook.com>
L: linux-mtd@lists.infradead.org
S: Supported
F: drivers/mtd/nand/atmel_nand*
label = "keyswitch_in";
gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
linux,code = <28>;
- gpio-key,wakeup;
+ wakeup-source;
};
error_in {
label = "error_in";
gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
linux,code = <29>;
- gpio-key,wakeup;
+ wakeup-source;
};
btn {
label = "btn";
gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
linux,code = <31>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
label = "Button";
gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
linux,code = <0x103>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
main_xtal {
clock-frequency = <18432000>;
};
label = "PB_RST";
gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
linux,code = <0x100>;
- gpio-key,wakeup;
+ wakeup-source;
};
user {
label = "PB_USER";
gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
linux,code = <0x101>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
label = "PB_PROG";
gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
linux,code = <0x102>;
- gpio-key,wakeup;
+ wakeup-source;
};
reset {
label = "PB_RST";
gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
linux,code = <0x100>;
- gpio-key,wakeup;
+ wakeup-source;
};
user {
label = "PB_USER";
gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
linux,code = <0x101>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
label = "PB_PROG";
gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
linux,code = <0x102>;
- gpio-key,wakeup;
+ wakeup-source;
};
reset {
label = "PB_RST";
gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
linux,code = <0x100>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
label = "user_pb";
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
linux,code = <28>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
/dts-v1/;
#include "sama5d2.dtsi"
#include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
/ {
model = "Atmel SAMA5D2 Xplained";
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
status = "okay";
};
+ sdmmc0: sdio-host@a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ non-removable;
+ mmc-ddr-1_8v;
+ status = "okay";
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ status = "okay"; /* conflict with qspi0 */
+ };
+
apb {
spi0: spi@f8000000 {
pinctrl-names = "default";
};
};
+ flx0: flexcom@f8034000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+ status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+
+ uart5: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&flx0_clk>;
+ clock-names = "usart";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx0_default>;
+ atmel,fifo-size = <32>;
+ status = "okay";
+ };
+ };
+
uart3: serial@fc008000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3_default>;
status = "okay";
};
+ flx4: flexcom@fc018000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "okay";
+
+ i2c2: i2c@600 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <0>, <0>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx4_clk>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx4_default>;
+ atmel,fifo-size = <16>;
+ status = "okay";
+ };
+ };
+
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
pinctrl-names = "default";
};
pinctrl@fc038000 {
+ pinctrl_flx0_default: flx0_default {
+ pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+ <PIN_PB29__FLEXCOM0_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_flx4_default: flx4_default {
+ pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+ <PIN_PD13__FLEXCOM4_IO1>;
+ bias-disable;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-pull-up;
+ };
+
+ ck_cd_rstn_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA10__SDMMC0_RSTN>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdmmc1_default: sdmmc1_default {
+ cmd_data {
+ pinmux = <PIN_PA28__SDMMC1_CMD>,
+ <PIN_PA18__SDMMC1_DAT0>,
+ <PIN_PA19__SDMMC1_DAT1>,
+ <PIN_PA20__SDMMC1_DAT2>,
+ <PIN_PA21__SDMMC1_DAT3>;
+ bias-pull-up;
+ };
+
+ conf-ck_cd {
+ pinmux = <PIN_PA22__SDMMC1_CK>,
+ <PIN_PA30__SDMMC1_CD>;
+ bias-disable;
+ };
+ };
+
pinctrl_spi0_default: spi0_default {
pinmux = <PIN_PA14__SPI0_SPCK>,
<PIN_PA15__SPI0_MOSI>,
label = "PB_USER";
gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
linux,code = <0x104>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
chosen {
- bootargs = "ignore_loglevel earlyprintk";
stdout-path = "serial0:115200n8";
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "pb_user1";
gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
linux,code = <0x100>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
chosen {
- bootargs = "ignore_loglevel earlyprintk";
stdout-path = "serial0:115200n8";
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "pb_user1";
gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
linux,code = <0x100>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
ti,debounce-tol = /bits/ 16 <65535>;
ti,debounce-max = /bits/ 16 <1>;
- linux,wakeup;
+ wakeup-source;
};
};
label = "button_0";
gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
linux,code = <256>;
- gpio-key,wakeup;
+ wakeup-source;
};
button_1 {
label = "button_1";
gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
linux,code = <257>;
- gpio-key,wakeup;
+ wakeup-source;
};
button_2 {
label = "button_2";
gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
linux,code = <258>;
- gpio-key,wakeup;
+ wakeup-source;
};
button_3 {
label = "button_3";
gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
linux,code = <259>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <16367660>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "left_click";
gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
linux,code = <272>;
- gpio-key,wakeup;
+ wakeup-source;
};
right_click {
label = "right_click";
gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
linux,code = <273>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <18432000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "Button 3";
gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
linux,code = <0x103>;
- gpio-key,wakeup;
+ wakeup-source;
};
btn4 {
label = "Button 4";
gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
linux,code = <0x104>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "left_click";
gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
linux,code = <272>;
- gpio-key,wakeup;
+ wakeup-source;
};
right_click {
label = "right_click";
gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
linux,code = <273>;
- gpio-key,wakeup;
+ wakeup-source;
};
left {
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <16000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "Enter";
gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
linux,code = <28>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
-
slow_xtal {
clock-frequency = <32768>;
};
label = "right_click";
gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
linux,code = <273>;
- gpio-key,wakeup;
+ wakeup-source;
};
left_click {
label = "left_click";
gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
linux,code = <272>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
reg = <0x20000000 0x8000000>;
};
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- main_clock: clock@0 {
- compatible = "atmel,osc", "fixed-clock";
- clock-frequency = <12000000>;
- };
- };
-
clocks {
slow_xtal {
clock-frequency = <32768>;
interrupt-names = "tx", "rx";
dmas = <&sdma_xbar 133>, <&sdma_xbar 132>;
dma-names = "tx", "rx";
- clocks = <&mcasp3_ahclkx_mux>;
- clock-names = "fck";
+ clocks = <&mcasp3_aux_gfclk_mux>, <&mcasp3_ahclkx_mux>;
+ clock-names = "fck", "ahclkx";
status = "disabled";
};
/* NetCP address range */
ranges = <0 0x26000000 0x1000000>;
- clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+ clocks = <&clkosr>, <&papllclk>, <&clkcpgmac>, <&chipclk12>;
dma-coherent;
ti,navigator-dmas = <&dma_gbe 0>,
};
poweroff@12100 {
compatible = "qnap,power-off";
- reg = <0x12000 0x100>;
+ reg = <0x12100 0x100>;
clocks = <&gate_clk 7>;
};
spi@10600 {
};
};
+&emmc {
+ /delete-property/mmc-hs200-1_8v;
+};
+
&gpio_keys {
pinctrl-0 = <&pwr_key_l &ap_lid_int_l &volum_down_l &volum_up_l>;
clock-names = "tsadc", "apb_pclk";
resets = <&cru SRST_TSADC>;
reset-names = "tsadc-apb";
- pinctrl-names = "default";
- pinctrl-0 = <&otp_out>;
+ pinctrl-names = "init", "default", "sleep";
+ pinctrl-0 = <&otp_gpio>;
+ pinctrl-1 = <&otp_out>;
+ pinctrl-2 = <&otp_gpio>;
#thermal-sensor-cells = <1>;
rockchip,hw-tshut-temp = <95000>;
status = "disabled";
};
tsadc {
+ otp_gpio: otp-gpio {
+ rockchip,pins = <0 10 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
otp_out: otp-out {
rockchip,pins = <0 10 RK_FUNC_1 &pcfg_pull_none>;
};
label = "pb_user1";
gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
linux,code = <0x100>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
};
};
watchdog@fc068640 {
- compatible = "atmel,at91sam9260-wdt";
+ compatible = "atmel,sama5d4-wdt";
reg = <0xfc068640 0x10>;
clocks = <&clk32k>;
status = "disabled";
label = "user_pb";
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
linux,code = <28>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
label = "user_pb";
gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
linux,code = <28>;
- gpio-key,wakeup;
+ wakeup-source;
};
};
interrupts = <67 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks VF610_CLK_DSPI0>;
clock-names = "dspi";
- spi-num-chipselects = <5>;
+ spi-num-chipselects = <6>;
status = "disabled";
};
interrupts = <68 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks VF610_CLK_DSPI1>;
clock-names = "dspi";
- spi-num-chipselects = <5>;
+ spi-num-chipselects = <4>;
status = "disabled";
};
clock-names = "adc";
#io-channel-cells = <1>;
status = "disabled";
+ fsl,adck-max-frequency = <30000000>, <40000000>,
+ <20000000>;
};
esdhc0: esdhc@400b1000 {
<&clks VF610_CLK_ESDHC0>;
clock-names = "ipg", "ahb", "per";
status = "disabled";
- fsl,adck-max-frequency = <30000000>, <40000000>,
- <20000000>;
};
esdhc1: esdhc@400b2000 {
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_SSB=m
CONFIG_MFD_ATMEL_HLCDC=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_POWER_SUPPLY=y
CONFIG_POWER_RESET=y
# CONFIG_HWMON is not set
-CONFIG_SSB=m
CONFIG_MFD_ATMEL_FLEXCOM=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@ check low interrupts
ldr \irqstat, [\base, #IRQ_CAUSE_LOW_OFF]
ldr \tmp, [\base, #IRQ_MASK_LOW_OFF]
- mov \irqnr, #31
+ mov \irqnr, #32
ands \irqstat, \irqstat, \tmp
@ if no low interrupts set, check high interrupts
ldreq \irqstat, [\base, #IRQ_CAUSE_HIGH_OFF]
ldreq \tmp, [\base, #IRQ_MASK_HIGH_OFF]
- moveq \irqnr, #63
+ moveq \irqnr, #64
andeqs \irqstat, \irqstat, \tmp
@ find first active interrupt source
.irq_unmask = imx_gpc_irq_unmask,
.irq_retrigger = irq_chip_retrigger_hierarchy,
.irq_set_wake = imx_gpc_irq_set_wake,
+ .irq_set_type = irq_chip_set_type_parent,
#ifdef CONFIG_SMP
.irq_set_affinity = irq_chip_set_affinity_parent,
#endif
* Ensure that CPU power state is set to ON to avoid CPU
* powerdomain transition on wfi
*/
- clkdm_wakeup(cpu1_clkdm);
- omap_set_pwrdm_state(cpu1_pwrdm, PWRDM_POWER_ON);
- clkdm_allow_idle(cpu1_clkdm);
+ clkdm_wakeup_nolock(cpu1_clkdm);
+ pwrdm_set_next_pwrst(cpu1_pwrdm, PWRDM_POWER_ON);
+ clkdm_allow_idle_nolock(cpu1_clkdm);
if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD)) {
while (gic_dist_disabled()) {
return ret;
}
+static void _enable_optional_clocks(struct omap_hwmod *oh)
+{
+ struct omap_hwmod_opt_clk *oc;
+ int i;
+
+ pr_debug("omap_hwmod: %s: enabling optional clocks\n", oh->name);
+
+ for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
+ if (oc->_clk) {
+ pr_debug("omap_hwmod: enable %s:%s\n", oc->role,
+ __clk_get_name(oc->_clk));
+ clk_enable(oc->_clk);
+ }
+}
+
+static void _disable_optional_clocks(struct omap_hwmod *oh)
+{
+ struct omap_hwmod_opt_clk *oc;
+ int i;
+
+ pr_debug("omap_hwmod: %s: disabling optional clocks\n", oh->name);
+
+ for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
+ if (oc->_clk) {
+ pr_debug("omap_hwmod: disable %s:%s\n", oc->role,
+ __clk_get_name(oc->_clk));
+ clk_disable(oc->_clk);
+ }
+}
+
/**
* _enable_clocks - enable hwmod main clock and interface clocks
* @oh: struct omap_hwmod *
clk_enable(os->_clk);
}
+ if (oh->flags & HWMOD_OPT_CLKS_NEEDED)
+ _enable_optional_clocks(oh);
+
/* The opt clocks are controlled by the device driver. */
return 0;
clk_disable(os->_clk);
}
+ if (oh->flags & HWMOD_OPT_CLKS_NEEDED)
+ _disable_optional_clocks(oh);
+
/* The opt clocks are controlled by the device driver. */
return 0;
}
-static void _enable_optional_clocks(struct omap_hwmod *oh)
-{
- struct omap_hwmod_opt_clk *oc;
- int i;
-
- pr_debug("omap_hwmod: %s: enabling optional clocks\n", oh->name);
-
- for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
- if (oc->_clk) {
- pr_debug("omap_hwmod: enable %s:%s\n", oc->role,
- __clk_get_name(oc->_clk));
- clk_enable(oc->_clk);
- }
-}
-
-static void _disable_optional_clocks(struct omap_hwmod *oh)
-{
- struct omap_hwmod_opt_clk *oc;
- int i;
-
- pr_debug("omap_hwmod: %s: disabling optional clocks\n", oh->name);
-
- for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
- if (oc->_clk) {
- pr_debug("omap_hwmod: disable %s:%s\n", oc->role,
- __clk_get_name(oc->_clk));
- clk_disable(oc->_clk);
- }
-}
-
/**
* _omap4_enable_module - enable CLKCTRL modulemode on OMAP4
* @oh: struct omap_hwmod *
* HWMOD_RECONFIG_IO_CHAIN: omap_hwmod code needs to reconfigure wake-up
* events by calling _reconfigure_io_chain() when a device is enabled
* or idled.
+ * HWMOD_OPT_CLKS_NEEDED: The optional clocks are needed for the module to
+ * operate and they need to be handled at the same time as the main_clk.
*/
#define HWMOD_SWSUP_SIDLE (1 << 0)
#define HWMOD_SWSUP_MSTANDBY (1 << 1)
#define HWMOD_FORCE_MSTANDBY (1 << 11)
#define HWMOD_SWSUP_SIDLE_ACT (1 << 12)
#define HWMOD_RECONFIG_IO_CHAIN (1 << 13)
+#define HWMOD_OPT_CLKS_NEEDED (1 << 14)
/*
* omap_hwmod._int_flags definitions
.dev_attr = &mcspi4_dev_attr,
};
+/*
+ * 'mcasp' class
+ *
+ */
+static struct omap_hwmod_class_sysconfig dra7xx_mcasp_sysc = {
+ .sysc_offs = 0x0004,
+ .sysc_flags = SYSC_HAS_SIDLEMODE,
+ .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+ .sysc_fields = &omap_hwmod_sysc_type3,
+};
+
+static struct omap_hwmod_class dra7xx_mcasp_hwmod_class = {
+ .name = "mcasp",
+ .sysc = &dra7xx_mcasp_sysc,
+};
+
+/* mcasp3 */
+static struct omap_hwmod_opt_clk mcasp3_opt_clks[] = {
+ { .role = "ahclkx", .clk = "mcasp3_ahclkx_mux" },
+};
+
+static struct omap_hwmod dra7xx_mcasp3_hwmod = {
+ .name = "mcasp3",
+ .class = &dra7xx_mcasp_hwmod_class,
+ .clkdm_name = "l4per2_clkdm",
+ .main_clk = "mcasp3_aux_gfclk_mux",
+ .flags = HWMOD_OPT_CLKS_NEEDED,
+ .prcm = {
+ .omap4 = {
+ .clkctrl_offs = DRA7XX_CM_L4PER2_MCASP3_CLKCTRL_OFFSET,
+ .context_offs = DRA7XX_RM_L4PER2_MCASP3_CONTEXT_OFFSET,
+ .modulemode = MODULEMODE_SWCTRL,
+ },
+ },
+ .opt_clks = mcasp3_opt_clks,
+ .opt_clks_cnt = ARRAY_SIZE(mcasp3_opt_clks),
+};
+
/*
* 'mmc' class
*
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
+/* l4_per2 -> mcasp3 */
+static struct omap_hwmod_ocp_if dra7xx_l4_per2__mcasp3 = {
+ .master = &dra7xx_l4_per2_hwmod,
+ .slave = &dra7xx_mcasp3_hwmod,
+ .clk = "l4_root_clk_div",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* l3_main_1 -> mcasp3 */
+static struct omap_hwmod_ocp_if dra7xx_l3_main_1__mcasp3 = {
+ .master = &dra7xx_l3_main_1_hwmod,
+ .slave = &dra7xx_mcasp3_hwmod,
+ .clk = "l3_iclk_div",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
/* l4_per1 -> elm */
static struct omap_hwmod_ocp_if dra7xx_l4_per1__elm = {
.master = &dra7xx_l4_per1_hwmod,
&dra7xx_l4_wkup__dcan1,
&dra7xx_l4_per2__dcan2,
&dra7xx_l4_per2__cpgmac0,
+ &dra7xx_l4_per2__mcasp3,
+ &dra7xx_l3_main_1__mcasp3,
&dra7xx_gmac__mdio,
&dra7xx_l4_cfg__dma_system,
&dra7xx_l3_main_1__dss,
.name = "l4_ls",
.clkdm_name = "alwon_l3s_clkdm",
.class = &l4_hwmod_class,
+ .flags = HWMOD_NO_IDLEST,
};
/*
.name = "l4_hs",
.clkdm_name = "alwon_l3_med_clkdm",
.class = &l4_hwmod_class,
+ .flags = HWMOD_NO_IDLEST,
};
/* L3 slow -> L4 ls peripheral interface running at 125MHz */
.name = "emac0",
.clkdm_name = "alwon_ethernet_clkdm",
.class = &dm816x_emac_hwmod_class,
+ .flags = HWMOD_NO_IDLEST,
};
static struct omap_hwmod_ocp_if dm81xx_l4_hs__emac0 = {
#include <linux/platform_data/iommu-omap.h>
#include <linux/platform_data/wkup_m3.h>
-#include <asm/siginfo.h>
-#include <asm/signal.h>
-
#include "common.h"
#include "common-board-devices.h"
#include "dss-common.h"
}
#endif /* CONFIG_ARCH_OMAP3 */
-#ifdef CONFIG_SOC_TI81XX
-static int fault_fixed_up;
-
-static int t410_abort_handler(unsigned long addr, unsigned int fsr,
- struct pt_regs *regs)
-{
- if ((fsr == 0x406 || fsr == 0xc06) && !fault_fixed_up) {
- pr_warn("External imprecise Data abort at addr=%#lx, fsr=%#x ignored.\n",
- addr, fsr);
- fault_fixed_up = 1;
- return 0;
- }
-
- return 1;
-}
-
-static void __init t410_abort_init(void)
-{
- hook_fault_code(16 + 6, t410_abort_handler, SIGBUS, BUS_OBJERR,
- "imprecise external abort");
-}
-#endif
-
#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
static struct iommu_platform_data omap4_iommu_pdata = {
.reset_name = "mmu_cache",
{ "openpandora,omap3-pandora-600mhz", omap3_pandora_legacy_init, },
{ "openpandora,omap3-pandora-1ghz", omap3_pandora_legacy_init, },
#endif
-#ifdef CONFIG_SOC_TI81XX
- { "hp,t410", t410_abort_init, },
-#endif
#ifdef CONFIG_SOC_OMAP5
{ "ti,omap5-uevm", omap5_uevm_legacy_init, },
#endif
if (omap_irq_pending())
return;
- trace_cpu_idle(1, smp_processor_id());
+ trace_cpu_idle_rcuidle(1, smp_processor_id());
omap_sram_idle();
- trace_cpu_idle(PWR_EVENT_EXIT, smp_processor_id());
+ trace_cpu_idle_rcuidle(PWR_EVENT_EXIT, smp_processor_id());
}
#ifdef CONFIG_SUSPEND
@ find cause bits that are unmasked
ands \irqstat, \irqstat, \tmp @ clear Z flag if any
clzne \irqnr, \irqstat @ calc irqnr
- rsbne \irqnr, \irqnr, #31
+ rsbne \irqnr, \irqnr, #32
.endm
{
palm_bl_power = bl;
palm_lcd_power = lcd;
- pwm_add_lookup(palm27x_pwm_lookup, ARRAY_SIZE(palm27x_pwm_lookup));
+ pwm_add_table(palm27x_pwm_lookup, ARRAY_SIZE(palm27x_pwm_lookup));
platform_device_register(&palm27x_backlight);
}
#endif
#if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
static struct pwm_lookup palmtc_pwm_lookup[] = {
PWM_LOOKUP("pxa25x-pwm.1", 0, "pwm-backlight.0", NULL, PALMTC_PERIOD_NS,
- PWM_PERIOD_NORMAL),
+ PWM_POLARITY_NORMAL),
};
static struct platform_pwm_backlight_data palmtc_backlight_data = {
#include "common.h"
#include "rcar-gen2.h"
-static const char *r8a7793_boards_compat_dt[] __initconst = {
+static const char * const r8a7793_boards_compat_dt[] __initconst = {
"renesas,r8a7793",
NULL,
};
select ARM_GLOBAL_TIMER
select HAVE_ARM_SCU if SMP
select HAVE_ARM_TWD if SMP
- select PM_GENERIC_DOMAINS
+ select PM_GENERIC_DOMAINS if PM
help
Support for ZTE ZX296702 SoC which is a dual core CortexA9MP
endif
module_platform_driver(omap_ocp2scp_driver);
-MODULE_ALIAS("platform: omap-ocp2scp");
+MODULE_ALIAS("platform:omap-ocp2scp");
MODULE_AUTHOR("Texas Instruments Inc.");
MODULE_DESCRIPTION("OMAP OCP2SCP driver");
MODULE_LICENSE("GPL v2");
config MTK_SCPSYS
bool "MediaTek SCPSYS Support"
depends on ARCH_MEDIATEK || COMPILE_TEST
+ default ARM64 && ARCH_MEDIATEK
select REGMAP
select MTK_INFRACFG
select PM_GENERIC_DOMAINS if PM
block++;
if (!block->size)
- return 0;
+ continue;
dev_dbg(kdev->dev, "linkram1: phys:%x, virt:%p, size:%x\n",
block->phys, block->virt, block->size);
for (i = 0; i < ARRAY_SIZE(knav_acc_firmwares); i++) {
if (knav_acc_firmwares[i]) {
- ret = request_firmware(&fw,
- knav_acc_firmwares[i],
- kdev->dev);
+ ret = request_firmware_direct(&fw,
+ knav_acc_firmwares[i],
+ kdev->dev);
if (!ret) {
found = true;
break;
int (*sensor_get_value)(u16, u32 *);
};
-#if IS_ENABLED(CONFIG_ARM_SCPI_PROTOCOL)
+#if IS_REACHABLE(CONFIG_ARM_SCPI_PROTOCOL)
struct scpi_ops *get_scpi_ops(void);
#else
static inline struct scpi_ops *get_scpi_ops(void) { return NULL; }
projects / linux-2.6-block.git / commitdiff