}
/**
- * zynq_qspi_setup - Configure the QSPI controller
+ * zynq_qspi_setup_op - Configure the QSPI controller
* @spi: Pointer to the spi_device structure
*
* Sets the operational mode of QSPI controller for the next QSPI transfer, baud
struct zynq_qspi *xqspi = spi_controller_get_devdata(mem->spi->master);
int err = 0, i;
u8 *tmpbuf;
- u8 opcode = op->cmd.opcode;
dev_dbg(xqspi->dev, "cmd:%#x mode:%d.%d.%d.%d\n",
- opcode, op->cmd.buswidth, op->addr.buswidth,
+ op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
op->dummy.buswidth, op->data.buswidth);
zynq_qspi_chipselect(mem->spi, true);
zynq_qspi_config_op(xqspi, mem->spi);
- if (op->cmd.nbytes) {
+ if (op->cmd.opcode) {
reinit_completion(&xqspi->data_completion);
- xqspi->txbuf = &opcode;
+ xqspi->txbuf = (u8 *)&op->cmd.opcode;
xqspi->rxbuf = NULL;
xqspi->tx_bytes = op->cmd.nbytes;
xqspi->rx_bytes = op->cmd.nbytes;
{
struct spi_device *spi = to_spi_device(dev);
- /* spi controllers may cleanup for released devices */
- if (spi->controller->cleanup)
- spi->controller->cleanup(spi);
-
spi_controller_put(spi->controller);
kfree(spi->driver_override);
kfree(spi);
return 0;
}
+static void spi_cleanup(struct spi_device *spi)
+{
+ if (spi->controller->cleanup)
+ spi->controller->cleanup(spi);
+}
+
/**
* spi_add_device - Add spi_device allocated with spi_alloc_device
* @spi: spi_device to register
/* Device may be bound to an active driver when this returns */
status = device_add(&spi->dev);
- if (status < 0)
+ if (status < 0) {
dev_err(dev, "can't add %s, status %d\n",
dev_name(&spi->dev), status);
- else
+ spi_cleanup(spi);
+ } else {
dev_dbg(dev, "registered child %s\n", dev_name(&spi->dev));
+ }
done:
mutex_unlock(&spi_add_lock);
if (ACPI_COMPANION(&spi->dev))
acpi_device_clear_enumerated(ACPI_COMPANION(&spi->dev));
device_remove_software_node(&spi->dev);
- device_unregister(&spi->dev);
+ device_del(&spi->dev);
+ spi_cleanup(spi);
+ put_device(&spi->dev);
}
EXPORT_SYMBOL_GPL(spi_unregister_device);
if (spi->cs_gpiod || gpio_is_valid(spi->cs_gpio)) {
if (!(spi->mode & SPI_NO_CS)) {
- if (spi->cs_gpiod)
- /* polarity handled by gpiolib */
- gpiod_set_value_cansleep(spi->cs_gpiod, activate);
- else
+ if (spi->cs_gpiod) {
+ /*
+ * Historically ACPI has no means of the GPIO polarity and
+ * thus the SPISerialBus() resource defines it on the per-chip
+ * basis. In order to avoid a chain of negations, the GPIO
+ * polarity is considered being Active High. Even for the cases
+ * when _DSD() is involved (in the updated versions of ACPI)
+ * the GPIO CS polarity must be defined Active High to avoid
+ * ambiguity. That's why we use enable, that takes SPI_CS_HIGH
+ * into account.
+ */
+ if (has_acpi_companion(&spi->dev))
+ gpiod_set_value_cansleep(spi->cs_gpiod, !enable);
+ else
+ /* Polarity handled by GPIO library */
+ gpiod_set_value_cansleep(spi->cs_gpiod, activate);
+ } else {
/*
* invert the enable line, as active low is
* default for SPI.
*/
gpio_set_value_cansleep(spi->cs_gpio, !enable);
+ }
}
/* Some SPI masters need both GPIO CS & slave_select */
if ((spi->controller->flags & SPI_MASTER_GPIO_SS) &&
if (spi->controller->set_cs_timing &&
!(spi->cs_gpiod || gpio_is_valid(spi->cs_gpio))) {
+ mutex_lock(&spi->controller->io_mutex);
+
if (spi->controller->auto_runtime_pm) {
status = pm_runtime_get_sync(parent);
if (status < 0) {
+ mutex_unlock(&spi->controller->io_mutex);
pm_runtime_put_noidle(parent);
dev_err(&spi->controller->dev, "Failed to power device: %d\n",
status);
hold, inactive);
pm_runtime_mark_last_busy(parent);
pm_runtime_put_autosuspend(parent);
- return status;
} else {
- return spi->controller->set_cs_timing(spi, setup, hold,
+ status = spi->controller->set_cs_timing(spi, setup, hold,
inactive);
}
+
+ mutex_unlock(&spi->controller->io_mutex);
+ return status;
}
if ((setup && setup->unit == SPI_DELAY_UNIT_SCK) ||