- compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795
SoC.
- reg: offset and length of the partial USB 2.0 Host register block.
-- reg-names: must be "usb2_host".
- clocks: clock phandle and specifier pair(s).
- #phy-cells: see phy-bindings.txt in the same directory, must be <0>.
Optional properties:
To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are
-combined, the device tree node should set HSUSB properties to reg and reg-names
-properties. This is because HSUSB has registers to select USB 2.0 host or
-peripheral at that channel:
-- reg: offset and length of the partial HSUSB register block.
-- reg-names: must be "hsusb".
+combined, the device tree node should set interrupt properties to use the
+channel as USB OTG:
- interrupts: interrupt specifier for the PHY.
Example (R-Car H3):
usb-phy@ee080200 {
compatible = "renesas,usb2-phy-r8a7795";
- reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>;
- reg-names = "usb2_host", "hsusb";
+ reg = <0 0xee080200 0 0x700>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&mstp7_clks R8A7795_CLK_EHCI0>,
- <&mstp7_clks R8A7795_CLK_HSUSB>;
+ clocks = <&mstp7_clks R8A7795_CLK_EHCI0>;
};
usb-phy@ee0a0200 {
compatible = "renesas,usb2-phy-r8a7795";
reg = <0 0xee0a0200 0 0x700>;
- reg-names = "usb2_host";
clocks = <&mstp7_clks R8A7795_CLK_EHCI0>;
};
--- /dev/null
+Rockchip specific extensions to the Analogix Display Port PHY
+------------------------------------
+
+Required properties:
+- compatible : should be one of the following supported values:
+ - "rockchip.rk3288-dp-phy"
+- clocks: from common clock binding: handle to dp clock.
+ of memory mapped region.
+- clock-names: from common clock binding:
+ Required elements: "24m"
+- rockchip,grf: phandle to the syscon managing the "general register files"
+- #phy-cells : from the generic PHY bindings, must be 0;
+
+Example:
+
+edp_phy: edp-phy {
+ compatible = "rockchip,rk3288-dp-phy";
+ rockchip,grf = <&grf>;
+ clocks = <&cru SCLK_EDP_24M>;
+ clock-names = "24m";
+ #phy-cells = <0>;
+};
--- /dev/null
+Rockchip EMMC PHY
+-----------------------
+
+Required properties:
+ - compatible: rockchip,rk3399-emmc-phy
+ - rockchip,grf : phandle to the syscon managing the "general
+ register files"
+ - #phy-cells: must be 0
+ - reg: PHY configure reg address offset in "general
+ register files"
+
+Example:
+
+emmcphy: phy {
+ compatible = "rockchip,rk3399-emmc-phy";
+ rockchip,grf = <&grf>;
+ reg = <0xf780>;
+ #phy-cells = <0>;
+};
ro [KNL] Mount root device read-only on boot
+ rockchip.usb_uart
+ Enable the uart passthrough on the designated usb port
+ on Rockchip SoCs. When active, the signals of the
+ debug-uart get routed to the D+ and D- pins of the usb
+ port and the regular usb controller gets disabled.
+
root= [KNL] Root filesystem
See name_to_dev_t comment in init/do_mounts.c.
config ARMADA375_USBCLUSTER_PHY
def_bool y
depends on MACH_ARMADA_375 || COMPILE_TEST
- depends on OF
+ depends on OF && HAS_IOMEM
select GENERIC_PHY
config PHY_DM816X_USB
help
Enable this to support the Rockchip USB 2.0 PHY.
+config PHY_ROCKCHIP_EMMC
+ tristate "Rockchip EMMC PHY Driver"
+ depends on ARCH_ROCKCHIP && OF
+ select GENERIC_PHY
+ help
+ Enable this to support the Rockchip EMMC PHY.
+
+config PHY_ROCKCHIP_DP
+ tristate "Rockchip Display Port PHY Driver"
+ depends on ARCH_ROCKCHIP && OF
+ select GENERIC_PHY
+ help
+ Enable this to support the Rockchip Display Port PHY.
+
config PHY_ST_SPEAR1310_MIPHY
tristate "ST SPEAR1310-MIPHY driver"
select GENERIC_PHY
obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
+obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
+obj-$(CONFIG_PHY_ROCKCHIP_DP) += phy-rockchip-dp.o
obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
#define USB2_ADPCTRL_IDPULLUP BIT(5) /* 1 = ID sampling is enabled */
#define USB2_ADPCTRL_DRVVBUS BIT(4)
-/******* HSUSB registers (original offset is +0x100) *******/
-#define HSUSB_LPSTS 0x02
-#define HSUSB_UGCTRL2 0x84
-
-/* Low Power Status register (LPSTS) */
-#define HSUSB_LPSTS_SUSPM 0x4000
-
-/* USB General control register 2 (UGCTRL2) */
-#define HSUSB_UGCTRL2_MASK 0x00000031 /* bit[31:6] should be 0 */
-#define HSUSB_UGCTRL2_USB0SEL 0x00000030
-#define HSUSB_UGCTRL2_USB0SEL_HOST 0x00000010
-#define HSUSB_UGCTRL2_USB0SEL_HS_USB 0x00000020
-#define HSUSB_UGCTRL2_USB0SEL_OTG 0x00000030
-
struct rcar_gen3_data {
void __iomem *base;
struct clk *clk;
struct rcar_gen3_chan {
struct rcar_gen3_data usb2;
- struct rcar_gen3_data hsusb;
struct phy *phy;
+ bool has_otg;
};
static void rcar_gen3_set_host_mode(struct rcar_gen3_chan *ch, int host)
{
struct rcar_gen3_chan *channel = phy_get_drvdata(p);
void __iomem *usb2_base = channel->usb2.base;
- void __iomem *hsusb_base = channel->hsusb.base;
- u32 val;
/* Initialize USB2 part */
writel(USB2_INT_ENABLE_INIT, usb2_base + USB2_INT_ENABLE);
writel(USB2_SPD_RSM_TIMSET_INIT, usb2_base + USB2_SPD_RSM_TIMSET);
writel(USB2_OC_TIMSET_INIT, usb2_base + USB2_OC_TIMSET);
- /* Initialize HSUSB part */
- if (hsusb_base) {
- val = readl(hsusb_base + HSUSB_UGCTRL2);
- val = (val & ~HSUSB_UGCTRL2_USB0SEL) |
- HSUSB_UGCTRL2_USB0SEL_OTG;
- writel(val & HSUSB_UGCTRL2_MASK, hsusb_base + HSUSB_UGCTRL2);
-
- /* Initialize otg part */
+ /* Initialize otg part */
+ if (channel->has_otg)
rcar_gen3_init_otg(channel);
- }
return 0;
}
{
struct rcar_gen3_chan *channel = phy_get_drvdata(p);
void __iomem *usb2_base = channel->usb2.base;
- void __iomem *hsusb_base = channel->hsusb.base;
u32 val;
val = readl(usb2_base + USB2_USBCTR);
val &= ~USB2_USBCTR_PLL_RST;
writel(val, usb2_base + USB2_USBCTR);
- /*
- * TODO: To reduce power consuming, this driver should set the SUSPM
- * after the PHY detects ID pin as peripheral.
- */
- if (hsusb_base) {
- /* Power on HSUSB PHY */
- val = readw(hsusb_base + HSUSB_LPSTS);
- val |= HSUSB_LPSTS_SUSPM;
- writew(val, hsusb_base + HSUSB_LPSTS);
- }
-
- return 0;
-}
-
-static int rcar_gen3_phy_usb2_power_off(struct phy *p)
-{
- struct rcar_gen3_chan *channel = phy_get_drvdata(p);
- void __iomem *hsusb_base = channel->hsusb.base;
- u32 val;
-
- if (hsusb_base) {
- /* Power off HSUSB PHY */
- val = readw(hsusb_base + HSUSB_LPSTS);
- val &= ~HSUSB_LPSTS_SUSPM;
- writew(val, hsusb_base + HSUSB_LPSTS);
- }
-
return 0;
}
.init = rcar_gen3_phy_usb2_init,
.exit = rcar_gen3_phy_usb2_exit,
.power_on = rcar_gen3_phy_usb2_power_on,
- .power_off = rcar_gen3_phy_usb2_power_off,
.owner = THIS_MODULE,
};
struct rcar_gen3_chan *channel;
struct phy_provider *provider;
struct resource *res;
+ int irq;
if (!dev->of_node) {
dev_err(dev, "This driver needs device tree\n");
if (!channel)
return -ENOMEM;
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usb2_host");
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
channel->usb2.base = devm_ioremap_resource(dev, res);
if (IS_ERR(channel->usb2.base))
return PTR_ERR(channel->usb2.base);
- /* "hsusb" memory resource is optional */
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "hsusb");
-
- /* To avoid error message by devm_ioremap_resource() */
- if (res) {
- int irq;
-
- channel->hsusb.base = devm_ioremap_resource(dev, res);
- if (IS_ERR(channel->hsusb.base))
- channel->hsusb.base = NULL;
- /* call request_irq for OTG */
- irq = platform_get_irq(pdev, 0);
- if (irq >= 0)
- irq = devm_request_irq(dev, irq, rcar_gen3_phy_usb2_irq,
- IRQF_SHARED, dev_name(dev),
- channel);
+ /* call request_irq for OTG */
+ irq = platform_get_irq(pdev, 0);
+ if (irq >= 0) {
+ irq = devm_request_irq(dev, irq, rcar_gen3_phy_usb2_irq,
+ IRQF_SHARED, dev_name(dev), channel);
if (irq < 0)
dev_err(dev, "No irq handler (%d)\n", irq);
+ channel->has_otg = true;
}
/* devm_phy_create() will call pm_runtime_enable(dev); */
--- /dev/null
+/*
+ * Rockchip DP PHY driver
+ *
+ * Copyright (C) 2016 FuZhou Rockchip Co., Ltd.
+ * Author: Yakir Yang <ykk@@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define GRF_SOC_CON12 0x0274
+
+#define GRF_EDP_REF_CLK_SEL_INTER_HIWORD_MASK BIT(20)
+#define GRF_EDP_REF_CLK_SEL_INTER BIT(4)
+
+#define GRF_EDP_PHY_SIDDQ_HIWORD_MASK BIT(21)
+#define GRF_EDP_PHY_SIDDQ_ON 0
+#define GRF_EDP_PHY_SIDDQ_OFF BIT(5)
+
+struct rockchip_dp_phy {
+ struct device *dev;
+ struct regmap *grf;
+ struct clk *phy_24m;
+};
+
+static int rockchip_set_phy_state(struct phy *phy, bool enable)
+{
+ struct rockchip_dp_phy *dp = phy_get_drvdata(phy);
+ int ret;
+
+ if (enable) {
+ ret = regmap_write(dp->grf, GRF_SOC_CON12,
+ GRF_EDP_PHY_SIDDQ_HIWORD_MASK |
+ GRF_EDP_PHY_SIDDQ_ON);
+ if (ret < 0) {
+ dev_err(dp->dev, "Can't enable PHY power %d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(dp->phy_24m);
+ } else {
+ clk_disable_unprepare(dp->phy_24m);
+
+ ret = regmap_write(dp->grf, GRF_SOC_CON12,
+ GRF_EDP_PHY_SIDDQ_HIWORD_MASK |
+ GRF_EDP_PHY_SIDDQ_OFF);
+ }
+
+ return ret;
+}
+
+static int rockchip_dp_phy_power_on(struct phy *phy)
+{
+ return rockchip_set_phy_state(phy, true);
+}
+
+static int rockchip_dp_phy_power_off(struct phy *phy)
+{
+ return rockchip_set_phy_state(phy, false);
+}
+
+static const struct phy_ops rockchip_dp_phy_ops = {
+ .power_on = rockchip_dp_phy_power_on,
+ .power_off = rockchip_dp_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int rockchip_dp_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct phy_provider *phy_provider;
+ struct rockchip_dp_phy *dp;
+ struct phy *phy;
+ int ret;
+
+ if (!np)
+ return -ENODEV;
+
+ dp = devm_kzalloc(dev, sizeof(*dp), GFP_KERNEL);
+ if (IS_ERR(dp))
+ return -ENOMEM;
+
+ dp->dev = dev;
+
+ dp->phy_24m = devm_clk_get(dev, "24m");
+ if (IS_ERR(dp->phy_24m)) {
+ dev_err(dev, "cannot get clock 24m\n");
+ return PTR_ERR(dp->phy_24m);
+ }
+
+ ret = clk_set_rate(dp->phy_24m, 24000000);
+ if (ret < 0) {
+ dev_err(dp->dev, "cannot set clock phy_24m %d\n", ret);
+ return ret;
+ }
+
+ dp->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
+ if (IS_ERR(dp->grf)) {
+ dev_err(dev, "rk3288-dp needs rockchip,grf property\n");
+ return PTR_ERR(dp->grf);
+ }
+
+ ret = regmap_write(dp->grf, GRF_SOC_CON12, GRF_EDP_REF_CLK_SEL_INTER |
+ GRF_EDP_REF_CLK_SEL_INTER_HIWORD_MASK);
+ if (ret != 0) {
+ dev_err(dp->dev, "Could not config GRF edp ref clk: %d\n", ret);
+ return ret;
+ }
+
+ phy = devm_phy_create(dev, np, &rockchip_dp_phy_ops);
+ if (IS_ERR(phy)) {
+ dev_err(dev, "failed to create phy\n");
+ return PTR_ERR(phy);
+ }
+ phy_set_drvdata(phy, dp);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id rockchip_dp_phy_dt_ids[] = {
+ { .compatible = "rockchip,rk3288-dp-phy" },
+ {}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_dp_phy_dt_ids);
+
+static struct platform_driver rockchip_dp_phy_driver = {
+ .probe = rockchip_dp_phy_probe,
+ .driver = {
+ .name = "rockchip-dp-phy",
+ .of_match_table = rockchip_dp_phy_dt_ids,
+ },
+};
+
+module_platform_driver(rockchip_dp_phy_driver);
+
+MODULE_AUTHOR("Yakir Yang <ykk@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip DP PHY driver");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+/*
+ * Rockchip emmc PHY driver
+ *
+ * Copyright (C) 2016 Shawn Lin <shawn.lin@rock-chips.com>
+ * Copyright (C) 2016 ROCKCHIP, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/*
+ * The higher 16-bit of this register is used for write protection
+ * only if BIT(x + 16) set to 1 the BIT(x) can be written.
+ */
+#define HIWORD_UPDATE(val, mask, shift) \
+ ((val) << (shift) | (mask) << ((shift) + 16))
+
+/* Register definition */
+#define GRF_EMMCPHY_CON0 0x0
+#define GRF_EMMCPHY_CON1 0x4
+#define GRF_EMMCPHY_CON2 0x8
+#define GRF_EMMCPHY_CON3 0xc
+#define GRF_EMMCPHY_CON4 0x10
+#define GRF_EMMCPHY_CON5 0x14
+#define GRF_EMMCPHY_CON6 0x18
+#define GRF_EMMCPHY_STATUS 0x20
+
+#define PHYCTRL_PDB_MASK 0x1
+#define PHYCTRL_PDB_SHIFT 0x0
+#define PHYCTRL_PDB_PWR_ON 0x1
+#define PHYCTRL_PDB_PWR_OFF 0x0
+#define PHYCTRL_ENDLL_MASK 0x1
+#define PHYCTRL_ENDLL_SHIFT 0x1
+#define PHYCTRL_ENDLL_ENABLE 0x1
+#define PHYCTRL_ENDLL_DISABLE 0x0
+#define PHYCTRL_CALDONE_MASK 0x1
+#define PHYCTRL_CALDONE_SHIFT 0x6
+#define PHYCTRL_CALDONE_DONE 0x1
+#define PHYCTRL_CALDONE_GOING 0x0
+#define PHYCTRL_DLLRDY_MASK 0x1
+#define PHYCTRL_DLLRDY_SHIFT 0x5
+#define PHYCTRL_DLLRDY_DONE 0x1
+#define PHYCTRL_DLLRDY_GOING 0x0
+
+struct rockchip_emmc_phy {
+ unsigned int reg_offset;
+ struct regmap *reg_base;
+};
+
+static int rockchip_emmc_phy_power(struct rockchip_emmc_phy *rk_phy,
+ bool on_off)
+{
+ unsigned int caldone;
+ unsigned int dllrdy;
+
+ /*
+ * Keep phyctrl_pdb and phyctrl_endll low to allow
+ * initialization of CALIO state M/C DFFs
+ */
+ regmap_write(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+ HIWORD_UPDATE(PHYCTRL_PDB_PWR_OFF,
+ PHYCTRL_PDB_MASK,
+ PHYCTRL_PDB_SHIFT));
+ regmap_write(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+ HIWORD_UPDATE(PHYCTRL_ENDLL_DISABLE,
+ PHYCTRL_ENDLL_MASK,
+ PHYCTRL_ENDLL_SHIFT));
+
+ /* Already finish power_off above */
+ if (on_off == PHYCTRL_PDB_PWR_OFF)
+ return 0;
+
+ /*
+ * According to the user manual, calpad calibration
+ * cycle takes more than 2us without the minimal recommended
+ * value, so we may need a little margin here
+ */
+ udelay(3);
+ regmap_write(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+ HIWORD_UPDATE(PHYCTRL_PDB_PWR_ON,
+ PHYCTRL_PDB_MASK,
+ PHYCTRL_PDB_SHIFT));
+
+ /*
+ * According to the user manual, it asks driver to
+ * wait 5us for calpad busy trimming
+ */
+ udelay(5);
+ regmap_read(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
+ &caldone);
+ caldone = (caldone >> PHYCTRL_CALDONE_SHIFT) & PHYCTRL_CALDONE_MASK;
+ if (caldone != PHYCTRL_CALDONE_DONE) {
+ pr_err("rockchip_emmc_phy_power: caldone timeout.\n");
+ return -ETIMEDOUT;
+ }
+
+ regmap_write(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_CON6,
+ HIWORD_UPDATE(PHYCTRL_ENDLL_ENABLE,
+ PHYCTRL_ENDLL_MASK,
+ PHYCTRL_ENDLL_SHIFT));
+ /*
+ * After enable analog DLL circuits, we need extra 10.2us
+ * for dll to be ready for work.
+ */
+ udelay(11);
+ regmap_read(rk_phy->reg_base,
+ rk_phy->reg_offset + GRF_EMMCPHY_STATUS,
+ &dllrdy);
+ dllrdy = (dllrdy >> PHYCTRL_DLLRDY_SHIFT) & PHYCTRL_DLLRDY_MASK;
+ if (dllrdy != PHYCTRL_DLLRDY_DONE) {
+ pr_err("rockchip_emmc_phy_power: dllrdy timeout.\n");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int rockchip_emmc_phy_power_off(struct phy *phy)
+{
+ struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
+ int ret = 0;
+
+ /* Power down emmc phy analog blocks */
+ ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_OFF);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rockchip_emmc_phy_power_on(struct phy *phy)
+{
+ struct rockchip_emmc_phy *rk_phy = phy_get_drvdata(phy);
+ int ret = 0;
+
+ /* Power up emmc phy analog blocks */
+ ret = rockchip_emmc_phy_power(rk_phy, PHYCTRL_PDB_PWR_ON);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static const struct phy_ops ops = {
+ .power_on = rockchip_emmc_phy_power_on,
+ .power_off = rockchip_emmc_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int rockchip_emmc_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct rockchip_emmc_phy *rk_phy;
+ struct phy *generic_phy;
+ struct phy_provider *phy_provider;
+ struct regmap *grf;
+ unsigned int reg_offset;
+
+ grf = syscon_regmap_lookup_by_phandle(dev->of_node, "rockchip,grf");
+ if (IS_ERR(grf)) {
+ dev_err(dev, "Missing rockchip,grf property\n");
+ return PTR_ERR(grf);
+ }
+
+ rk_phy = devm_kzalloc(dev, sizeof(*rk_phy), GFP_KERNEL);
+ if (!rk_phy)
+ return -ENOMEM;
+
+ if (of_property_read_u32(dev->of_node, "reg", ®_offset)) {
+ dev_err(dev, "missing reg property in node %s\n",
+ dev->of_node->name);
+ return -EINVAL;
+ }
+
+ rk_phy->reg_offset = reg_offset;
+ rk_phy->reg_base = grf;
+
+ generic_phy = devm_phy_create(dev, dev->of_node, &ops);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "failed to create PHY\n");
+ return PTR_ERR(generic_phy);
+ }
+
+ phy_set_drvdata(generic_phy, rk_phy);
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id rockchip_emmc_phy_dt_ids[] = {
+ { .compatible = "rockchip,rk3399-emmc-phy" },
+ {}
+};
+
+MODULE_DEVICE_TABLE(of, rockchip_emmc_phy_dt_ids);
+
+static struct platform_driver rockchip_emmc_driver = {
+ .probe = rockchip_emmc_phy_probe,
+ .driver = {
+ .name = "rockchip-emmc-phy",
+ .of_match_table = rockchip_emmc_phy_dt_ids,
+ },
+};
+
+module_platform_driver(rockchip_emmc_driver);
+
+MODULE_AUTHOR("Shawn Lin <shawn.lin@rock-chips.com>");
+MODULE_DESCRIPTION("Rockchip EMMC PHY driver");
+MODULE_LICENSE("GPL v2");
#include <linux/regmap.h>
#include <linux/mfd/syscon.h>
-/*
- * The higher 16-bit of this register is used for write protection
- * only if BIT(13 + 16) set to 1 the BIT(13) can be written.
- */
-#define SIDDQ_WRITE_ENA BIT(29)
-#define SIDDQ_ON BIT(13)
-#define SIDDQ_OFF (0 << 13)
+static int enable_usb_uart;
+
+#define HIWORD_UPDATE(val, mask) \
+ ((val) | (mask) << 16)
+
+#define UOC_CON0_SIDDQ BIT(13)
struct rockchip_usb_phys {
int reg;
const char *pll_name;
};
+struct rockchip_usb_phy_base;
struct rockchip_usb_phy_pdata {
struct rockchip_usb_phys *phys;
+ int (*init_usb_uart)(struct regmap *grf);
+ int usb_uart_phy;
};
struct rockchip_usb_phy_base {
struct clk *clk480m;
struct clk_hw clk480m_hw;
struct phy *phy;
+ bool uart_enabled;
};
static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy,
bool siddq)
{
- return regmap_write(phy->base->reg_base, phy->reg_offset,
- SIDDQ_WRITE_ENA | (siddq ? SIDDQ_ON : SIDDQ_OFF));
+ u32 val = HIWORD_UPDATE(siddq ? UOC_CON0_SIDDQ : 0, UOC_CON0_SIDDQ);
+
+ return regmap_write(phy->base->reg_base, phy->reg_offset, val);
}
static unsigned long rockchip_usb_phy480m_recalc_rate(struct clk_hw *hw,
if (ret < 0)
return ret;
- return (val & SIDDQ_ON) ? 0 : 1;
+ return (val & UOC_CON0_SIDDQ) ? 0 : 1;
}
static const struct clk_ops rockchip_usb_phy480m_ops = {
{
struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+ if (phy->uart_enabled)
+ return -EBUSY;
+
clk_disable_unprepare(phy->clk480m);
return 0;
{
struct rockchip_usb_phy *phy = phy_get_drvdata(_phy);
+ if (phy->uart_enabled)
+ return -EBUSY;
+
return clk_prepare_enable(phy->clk480m);
}
{
struct rockchip_usb_phy *rk_phy = data;
- of_clk_del_provider(rk_phy->np);
- clk_unregister(rk_phy->clk480m);
+ if (!rk_phy->uart_enabled) {
+ of_clk_del_provider(rk_phy->np);
+ clk_unregister(rk_phy->clk480m);
+ }
if (rk_phy->clk)
clk_put(rk_phy->clk);
return -EINVAL;
}
- if (rk_phy->clk) {
- clk_name = __clk_get_name(rk_phy->clk);
- init.flags = 0;
- init.parent_names = &clk_name;
- init.num_parents = 1;
+ if (enable_usb_uart && base->pdata->usb_uart_phy == i) {
+ dev_dbg(base->dev, "phy%d used as uart output\n", i);
+ rk_phy->uart_enabled = true;
} else {
- init.flags = CLK_IS_ROOT;
- init.parent_names = NULL;
- init.num_parents = 0;
- }
+ if (rk_phy->clk) {
+ clk_name = __clk_get_name(rk_phy->clk);
+ init.flags = 0;
+ init.parent_names = &clk_name;
+ init.num_parents = 1;
+ } else {
+ init.flags = CLK_IS_ROOT;
+ init.parent_names = NULL;
+ init.num_parents = 0;
+ }
- init.ops = &rockchip_usb_phy480m_ops;
- rk_phy->clk480m_hw.init = &init;
+ init.ops = &rockchip_usb_phy480m_ops;
+ rk_phy->clk480m_hw.init = &init;
- rk_phy->clk480m = clk_register(base->dev, &rk_phy->clk480m_hw);
- if (IS_ERR(rk_phy->clk480m)) {
- err = PTR_ERR(rk_phy->clk480m);
- goto err_clk;
- }
+ rk_phy->clk480m = clk_register(base->dev, &rk_phy->clk480m_hw);
+ if (IS_ERR(rk_phy->clk480m)) {
+ err = PTR_ERR(rk_phy->clk480m);
+ goto err_clk;
+ }
- err = of_clk_add_provider(child, of_clk_src_simple_get,
- rk_phy->clk480m);
- if (err < 0)
- goto err_clk_prov;
+ err = of_clk_add_provider(child, of_clk_src_simple_get,
+ rk_phy->clk480m);
+ if (err < 0)
+ goto err_clk_prov;
+ }
err = devm_add_action(base->dev, rockchip_usb_phy_action, rk_phy);
if (err)
}
phy_set_drvdata(rk_phy->phy, rk_phy);
- /* only power up usb phy when it use, so disable it when init*/
- return rockchip_usb_phy_power(rk_phy, 1);
+ /*
+ * When acting as uart-pipe, just keep clock on otherwise
+ * only power up usb phy when it use, so disable it when init
+ */
+ if (rk_phy->uart_enabled)
+ return clk_prepare_enable(rk_phy->clk);
+ else
+ return rockchip_usb_phy_power(rk_phy, 1);
err_devm_action:
- of_clk_del_provider(child);
+ if (!rk_phy->uart_enabled)
+ of_clk_del_provider(child);
err_clk_prov:
- clk_unregister(rk_phy->clk480m);
+ if (!rk_phy->uart_enabled)
+ clk_unregister(rk_phy->clk480m);
err_clk:
if (rk_phy->clk)
clk_put(rk_phy->clk);
},
};
+#define RK3288_UOC0_CON0 0x320
+#define RK3288_UOC0_CON0_COMMON_ON_N BIT(0)
+#define RK3288_UOC0_CON0_DISABLE BIT(4)
+
+#define RK3288_UOC0_CON2 0x328
+#define RK3288_UOC0_CON2_SOFT_CON_SEL BIT(2)
+
+#define RK3288_UOC0_CON3 0x32c
+#define RK3288_UOC0_CON3_UTMI_SUSPENDN BIT(0)
+#define RK3288_UOC0_CON3_UTMI_OPMODE_NODRIVING (1 << 1)
+#define RK3288_UOC0_CON3_UTMI_OPMODE_MASK (3 << 1)
+#define RK3288_UOC0_CON3_UTMI_XCVRSEELCT_FSTRANSC (1 << 3)
+#define RK3288_UOC0_CON3_UTMI_XCVRSEELCT_MASK (3 << 3)
+#define RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED BIT(5)
+#define RK3288_UOC0_CON3_BYPASSDMEN BIT(6)
+#define RK3288_UOC0_CON3_BYPASSSEL BIT(7)
+
+/*
+ * Enable the bypass of uart2 data through the otg usb phy.
+ * Original description in the TRM.
+ * 1. Disable the OTG block by setting OTGDISABLE0 to 1’b1.
+ * 2. Disable the pull-up resistance on the D+ line by setting
+ * OPMODE0[1:0] to 2’b01.
+ * 3. To ensure that the XO, Bias, and PLL blocks are powered down in Suspend
+ * mode, set COMMONONN to 1’b1.
+ * 4. Place the USB PHY in Suspend mode by setting SUSPENDM0 to 1’b0.
+ * 5. Set BYPASSSEL0 to 1’b1.
+ * 6. To transmit data, controls BYPASSDMEN0, and BYPASSDMDATA0.
+ * To receive data, monitor FSVPLUS0.
+ *
+ * The actual code in the vendor kernel does some things differently.
+ */
+static int __init rk3288_init_usb_uart(struct regmap *grf)
+{
+ u32 val;
+ int ret;
+
+ /*
+ * COMMON_ON and DISABLE settings are described in the TRM,
+ * but were not present in the original code.
+ * Also disable the analog phy components to save power.
+ */
+ val = HIWORD_UPDATE(RK3288_UOC0_CON0_COMMON_ON_N
+ | RK3288_UOC0_CON0_DISABLE
+ | UOC_CON0_SIDDQ,
+ RK3288_UOC0_CON0_COMMON_ON_N
+ | RK3288_UOC0_CON0_DISABLE
+ | UOC_CON0_SIDDQ);
+ ret = regmap_write(grf, RK3288_UOC0_CON0, val);
+ if (ret)
+ return ret;
+
+ val = HIWORD_UPDATE(RK3288_UOC0_CON2_SOFT_CON_SEL,
+ RK3288_UOC0_CON2_SOFT_CON_SEL);
+ ret = regmap_write(grf, RK3288_UOC0_CON2, val);
+ if (ret)
+ return ret;
+
+ val = HIWORD_UPDATE(RK3288_UOC0_CON3_UTMI_OPMODE_NODRIVING
+ | RK3288_UOC0_CON3_UTMI_XCVRSEELCT_FSTRANSC
+ | RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED,
+ RK3288_UOC0_CON3_UTMI_SUSPENDN
+ | RK3288_UOC0_CON3_UTMI_OPMODE_MASK
+ | RK3288_UOC0_CON3_UTMI_XCVRSEELCT_MASK
+ | RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED);
+ ret = regmap_write(grf, RK3288_UOC0_CON3, val);
+ if (ret)
+ return ret;
+
+ val = HIWORD_UPDATE(RK3288_UOC0_CON3_BYPASSSEL
+ | RK3288_UOC0_CON3_BYPASSDMEN,
+ RK3288_UOC0_CON3_BYPASSSEL
+ | RK3288_UOC0_CON3_BYPASSDMEN);
+ ret = regmap_write(grf, RK3288_UOC0_CON3, val);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
static const struct rockchip_usb_phy_pdata rk3288_pdata = {
.phys = (struct rockchip_usb_phys[]){
{ .reg = 0x320, .pll_name = "sclk_otgphy0_480m" },
{ .reg = 0x348, .pll_name = "sclk_otgphy2_480m" },
{ /* sentinel */ }
},
+ .init_usb_uart = rk3288_init_usb_uart,
+ .usb_uart_phy = 0,
};
static int rockchip_usb_phy_probe(struct platform_device *pdev)
module_platform_driver(rockchip_usb_driver);
+#ifndef MODULE
+static int __init rockchip_init_usb_uart(void)
+{
+ const struct of_device_id *match;
+ const struct rockchip_usb_phy_pdata *data;
+ struct device_node *np;
+ struct regmap *grf;
+ int ret;
+
+ if (!enable_usb_uart)
+ return 0;
+
+ np = of_find_matching_node_and_match(NULL, rockchip_usb_phy_dt_ids,
+ &match);
+ if (!np) {
+ pr_err("%s: failed to find usbphy node\n", __func__);
+ return -ENOTSUPP;
+ }
+
+ pr_debug("%s: using settings for %s\n", __func__, match->compatible);
+ data = match->data;
+
+ if (!data->init_usb_uart) {
+ pr_err("%s: usb-uart not available on %s\n",
+ __func__, match->compatible);
+ return -ENOTSUPP;
+ }
+
+ grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
+ if (IS_ERR(grf)) {
+ pr_err("%s: Missing rockchip,grf property, %lu\n",
+ __func__, PTR_ERR(grf));
+ return PTR_ERR(grf);
+ }
+
+ ret = data->init_usb_uart(grf);
+ if (ret) {
+ pr_err("%s: could not init usb_uart, %d\n", __func__, ret);
+ enable_usb_uart = 0;
+ return ret;
+ }
+
+ return 0;
+}
+early_initcall(rockchip_init_usb_uart);
+
+static int __init rockchip_usb_uart(char *buf)
+{
+ enable_usb_uart = true;
+ return 0;
+}
+early_param("rockchip.usb_uart", rockchip_usb_uart);
+#endif
+
MODULE_AUTHOR("Yunzhi Li <lyz@rock-chips.com>");
MODULE_DESCRIPTION("Rockchip USB 2.0 PHY driver");
MODULE_LICENSE("GPL v2");
projects / linux-2.6-block.git / commitdiff