select HAVE_IDE
select PM_GENERIC_DOMAINS if PM
select PM_GENERIC_DOMAINS_OF if PM && OF
+ select REGMAP_MMIO
select RESET_CONTROLLER
select SPARSE_IRQ
select USE_OF
};
&hdmi {
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
&pwm {
reg = <2>;
};
- switch@0 {
+ switch@10 {
compatible = "qca,qca8334";
- reg = <0>;
+ reg = <10>;
switch_ports: ports {
#address-cells = <1>;
ethphy0: port@0 {
reg = <0>;
label = "cpu";
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
ethernet = <&fec>;
fixed-link {
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
vmcc-supply = <®_sd3_vmmc>;
cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- bus-witdh = <4>;
+ bus-width = <4>;
no-1-8-v;
status = "okay";
};
pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
vmcc-supply = <®_sd4_vmmc>;
- bus-witdh = <8>;
+ bus-width = <8>;
no-1-8-v;
non-removable;
status = "okay";
pinctrl-0 = <&pinctrl_enet>;
phy-handle = <ðphy>;
phy-mode = "rgmii";
+ phy-reset-duration = <10>; /* in msecs */
phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
phy-supply = <&vdd_eth_io_reg>;
status = "disabled";
-// SPDX-License-Identifier: GPL-2.0
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2016 Freescale Semiconductor, Inc.
* Copyright (C) 2017 NXP
gpio-sck = <&gpio0 5 GPIO_ACTIVE_HIGH>;
gpio-mosi = <&gpio0 4 GPIO_ACTIVE_HIGH>;
/*
- * It's not actually active high, but the frameworks assume
- * the polarity of the passed-in GPIO is "normal" (active
- * high) then actively drives the line low to select the
- * chip.
+ * This chipselect is active high. Just setting the flags
+ * to GPIO_ACTIVE_HIGH is not enough for the SPI DT bindings,
+ * it will be ignored, only the special "spi-cs-high" flag
+ * really counts.
*/
cs-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ spi-cs-high;
num-chipselects = <1>;
/*
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_IIO=y
CONFIG_FSL_MX25_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_IMX1=y
+CONFIG_PWM_IMX27=y
CONFIG_EXT4_FS=y
# CONFIG_DNOTIFY is not set
CONFIG_VFAT_FS=y
CONFIG_MPL3115=y
CONFIG_PWM=y
CONFIG_PWM_FSL_FTM=y
-CONFIG_PWM_IMX=y
+CONFIG_PWM_IMX27=y
CONFIG_NVMEM_IMX_OCOTP=y
CONFIG_NVMEM_VF610_OCOTP=y
CONFIG_TEE=y
#include "cpuidle.h"
#include "hardware.h"
-static atomic_t master = ATOMIC_INIT(0);
-static DEFINE_SPINLOCK(master_lock);
+static int num_idle_cpus = 0;
+static DEFINE_SPINLOCK(cpuidle_lock);
static int imx6q_enter_wait(struct cpuidle_device *dev,
struct cpuidle_driver *drv, int index)
{
- if (atomic_inc_return(&master) == num_online_cpus()) {
- /*
- * With this lock, we prevent other cpu to exit and enter
- * this function again and become the master.
- */
- if (!spin_trylock(&master_lock))
- goto idle;
+ spin_lock(&cpuidle_lock);
+ if (++num_idle_cpus == num_online_cpus())
imx6_set_lpm(WAIT_UNCLOCKED);
- cpu_do_idle();
- imx6_set_lpm(WAIT_CLOCKED);
- spin_unlock(&master_lock);
- goto done;
- }
+ spin_unlock(&cpuidle_lock);
-idle:
cpu_do_idle();
-done:
- atomic_dec(&master);
+
+ spin_lock(&cpuidle_lock);
+ if (num_idle_cpus-- == num_online_cpus())
+ imx6_set_lpm(WAIT_CLOCKED);
+ spin_unlock(&cpuidle_lock);
return index;
}
return;
m4if_base = of_iomap(np, 0);
+ of_node_put(np);
if (!m4if_base) {
pr_err("Unable to map M4IF registers\n");
return;
bool "Broadcom BCM2835 family"
select TIMER_OF
select GPIOLIB
+ select MFD_CORE
select PINCTRL
select PINCTRL_BCM2835
select ARM_AMBA
nvidia,default-trim = <0x9>;
nvidia,dqs-trim = <63>;
mmc-hs400-1_8v;
- supports-cqe;
status = "disabled";
};
/*
* Device Tree Source for the RZ/G2E (R8A774C0) SoC
*
- * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018-2019 Renesas Electronics Corp.
*/
#include <dt-bindings/clock/r8a774c0-cpg-mssr.h>
<&cpg CPG_CORE R8A774C0_CLK_S3D1C>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
- <&dmac2 0x5b>, <&dmac2 0x5a>;
- dma-names = "tx", "rx", "tx", "rx";
+ dmas = <&dmac0 0x5b>, <&dmac0 0x5a>;
+ dma-names = "tx", "rx";
power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
resets = <&cpg 202>;
status = "disabled";
/*
* Device Tree Source for the R-Car E3 (R8A77990) SoC
*
- * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018-2019 Renesas Electronics Corp.
*/
#include <dt-bindings/clock/r8a77990-cpg-mssr.h>
<&cpg CPG_CORE R8A77990_CLK_S3D1C>,
<&scif_clk>;
clock-names = "fck", "brg_int", "scif_clk";
- dmas = <&dmac1 0x5b>, <&dmac1 0x5a>,
- <&dmac2 0x5b>, <&dmac2 0x5a>;
- dma-names = "tx", "rx", "tx", "rx";
+ dmas = <&dmac0 0x5b>, <&dmac0 0x5a>;
+ dma-names = "tx", "rx";
power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
resets = <&cpg 202>;
status = "disabled";
static int bcm2835_asb_enable(struct bcm2835_power *power, u32 reg)
{
- u64 start = ktime_get_ns();
+ u64 start;
+
+ if (!reg)
+ return 0;
+
+ start = ktime_get_ns();
/* Enable the module's async AXI bridges. */
ASB_WRITE(reg, ASB_READ(reg) & ~ASB_REQ_STOP);
static int bcm2835_asb_disable(struct bcm2835_power *power, u32 reg)
{
- u64 start = ktime_get_ns();
+ u64 start;
+
+ if (!reg)
+ return 0;
+
+ start = ktime_get_ns();
/* Enable the module's async AXI bridges. */
ASB_WRITE(reg, ASB_READ(reg) | ASB_REQ_STOP);
}
}
-static void
+static int
bcm2835_init_power_domain(struct bcm2835_power *power,
int pd_xlate_index, const char *name)
{
struct bcm2835_power_domain *dom = &power->domains[pd_xlate_index];
dom->clk = devm_clk_get(dev->parent, name);
+ if (IS_ERR(dom->clk)) {
+ int ret = PTR_ERR(dom->clk);
+
+ if (ret == -EPROBE_DEFER)
+ return ret;
+
+ /* Some domains don't have a clk, so make sure that we
+ * don't deref an error pointer later.
+ */
+ dom->clk = NULL;
+ }
dom->base.name = name;
dom->base.power_on = bcm2835_power_pd_power_on;
pm_genpd_init(&dom->base, NULL, true);
power->pd_xlate.domains[pd_xlate_index] = &dom->base;
+
+ return 0;
}
/** bcm2835_reset_reset - Resets a block that has a reset line in the
{ BCM2835_POWER_DOMAIN_IMAGE_PERI, BCM2835_POWER_DOMAIN_CAM0 },
{ BCM2835_POWER_DOMAIN_IMAGE_PERI, BCM2835_POWER_DOMAIN_CAM1 },
};
- int ret, i;
+ int ret = 0, i;
u32 id;
power = devm_kzalloc(dev, sizeof(*power), GFP_KERNEL);
power->pd_xlate.num_domains = ARRAY_SIZE(power_domain_names);
- for (i = 0; i < ARRAY_SIZE(power_domain_names); i++)
- bcm2835_init_power_domain(power, i, power_domain_names[i]);
+ for (i = 0; i < ARRAY_SIZE(power_domain_names); i++) {
+ ret = bcm2835_init_power_domain(power, i, power_domain_names[i]);
+ if (ret)
+ goto fail;
+ }
for (i = 0; i < ARRAY_SIZE(domain_deps); i++) {
pm_genpd_add_subdomain(&power->domains[domain_deps[i].parent].base,
ret = devm_reset_controller_register(dev, &power->reset);
if (ret)
- return ret;
+ goto fail;
of_genpd_add_provider_onecell(dev->parent->of_node, &power->pd_xlate);
dev_info(dev, "Broadcom BCM2835 power domains driver");
return 0;
+
+fail:
+ for (i = 0; i < ARRAY_SIZE(power_domain_names); i++) {
+ struct generic_pm_domain *dom = &power->domains[i].base;
+
+ if (dom->name)
+ pm_genpd_remove(dom);
+ }
+ return ret;
}
static int bcm2835_power_remove(struct platform_device *pdev)
projects / linux-2.6-block.git / commitdiff