netxen: fix failure cases for fw hang recovery

Handle few corner cases in firmware hang detection and recovery:

o Don't mark device state as READY, till handshake with
  firmware is done.
o During probe, if start_firmware fails, restore reference
  count.
o Don't increment refernce count, if start_firmware fails
  during firmware reset.
o Clear __NX_RESETTING bit, incase of fatal error or tempeature
  reaches critical limit so that pci remove() doesn't poll on
  this bit.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c
index 838420dbc633ee0af56b1a57107989edf7b16635..e5d187fce51b537dd1f7fe066eb4b6cd642e4caa 100644 (file)
--- a/drivers/net/netxen/netxen_nic_main.c
+++ b/drivers/net/netxen/netxen_nic_main.c
@@ -819,7 +819,7 @@ netxen_start_firmware(struct netxen_adapter *adapter)
        if (err < 0)
                goto err_out;
        if (err == 0)
-               goto ready;
+               goto wait_init;
 
        if (first_boot != 0x55555555) {
                NXWR32(adapter, CRB_CMDPEG_STATE, 0);
@@ -862,9 +862,6 @@ netxen_start_firmware(struct netxen_adapter *adapter)
                | (_NETXEN_NIC_LINUX_SUBVERSION);
        NXWR32(adapter, CRB_DRIVER_VERSION, val);
 
-ready:
-       NXWR32(adapter, NX_CRB_DEV_STATE, NX_DEV_READY);
-
 wait_init:
        /* Handshake with the card before we register the devices. */
        err = netxen_phantom_init(adapter, NETXEN_NIC_PEG_TUNE);
@@ -873,6 +870,8 @@ wait_init:
                goto err_out;
        }
 
+       NXWR32(adapter, NX_CRB_DEV_STATE, NX_DEV_READY);
+
        nx_update_dma_mask(adapter);
 
        netxen_check_options(adapter);
@@ -1282,7 +1281,7 @@ netxen_nic_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
        err = netxen_start_firmware(adapter);
        if (err)
-               goto err_out_iounmap;
+               goto err_out_decr_ref;
 
        /*
         * See if the firmware gave us a virtual-physical port mapping.
@@ -1326,6 +1325,7 @@ err_out_disable_msi:
 
        netxen_free_dummy_dma(adapter);
 
+err_out_decr_ref:
        nx_decr_dev_ref_cnt(adapter);
 
 err_out_iounmap:
@@ -2189,14 +2189,13 @@ netxen_fwinit_work(struct work_struct *work)
                                        netxen_fwinit_work, 2 * FW_POLL_DELAY);
                        return;
                }
-               break;
 
        case NX_DEV_FAILED:
        default:
+               nx_incr_dev_ref_cnt(adapter);
                break;
        }
 
-       nx_incr_dev_ref_cnt(adapter);
        clear_bit(__NX_RESETTING, &adapter->state);
 }
 
@@ -2218,18 +2217,23 @@ netxen_detach_work(struct work_struct *work)
 
        status = NXRD32(adapter, NETXEN_PEG_HALT_STATUS1);
 
-       ref_cnt = nx_decr_dev_ref_cnt(adapter);
-
        if (status & NX_RCODE_FATAL_ERROR)
-               return;
+               goto err_ret;
 
        if (adapter->temp == NX_TEMP_PANIC)
-               return;
+               goto err_ret;
+
+       ref_cnt = nx_decr_dev_ref_cnt(adapter);
 
        delay = (ref_cnt == 0) ? 0 : (2 * FW_POLL_DELAY);
 
        adapter->fw_wait_cnt = 0;
        netxen_schedule_work(adapter, netxen_fwinit_work, delay);
+
+       return;
+
+err_ret:
+       clear_bit(__NX_RESETTING, &adapter->state);
 }
 
 static int