staging: olpc_dcon: drop XO-1.5 prototype support
authorAndres Salomon <dilinger@queued.net>
Fri, 11 Feb 2011 01:49:58 +0000 (17:49 -0800)
committerGreg Kroah-Hartman <gregkh@suse.de>
Fri, 18 Feb 2011 20:33:20 +0000 (12:33 -0800)
Remove code related to XO-1.5 prototype boards.

Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/staging/olpc_dcon/olpc_dcon_xo_1_5.c

index 4f56098bb36638a1a5fff60e8818d84a9786b6fe..5ef05406a8b8c50adbe9d8a0312e70da969ba123 100644 (file)
 
 /* Hardware setup on the XO 1.5:
  *     DCONLOAD connects to
- *             VX855_GPO12 (not nCR_PWOFF)   (rev A)
- *             VX855_GPIO1 (not SMBCK2)      (rev B)
+ *             VX855_GPIO1 (not SMBCK2)
  *     DCONBLANK connects to VX855_GPIO8 (not SSPICLK)  unused in driver
  *     DCONSTAT0 connects to VX855_GPI10 (not SSPISDI)
  *     DCONSTAT1 connects to VX855_GPI11 (not nSSPISS)
- *     DCONIRQ connects to VX855_GPIO12 (on B3.  on B2, it goes to
- *             SMBALRT, which doesn't work.)
+ *     DCONIRQ connects to VX855_GPIO12
  *     DCONSMBDATA connects to VX855 graphics CRTSPD
  *     DCONSMBCLK connects to VX855 graphics CRTSPCLK
  */
 
-#define TEST_B2 0   // define to test B3 paths on a modded B2 board
-
 #define VX855_GENL_PURPOSE_OUTPUT 0x44c // PMIO_Rx4c-4f
 #define VX855_GPI_STATUS_CHG 0x450  // PMIO_Rx50
 #define VX855_GPI_SCI_SMI 0x452  // PMIO_Rx52
 
 #define PREFIX "OLPC DCON:"
 
-/*
-  there is no support here for DCONIRQ on 1.5 boards earlier than
-  B3.  the issue is that the DCONIRQ signal on earlier boards is
-  routed to SMBALRT, which turns out to to be a level sensitive
-  interrupt.  the DCONIRQ signal is far too short (11usec) to
-  be detected reliably in that case.  including support for
-  DCONIRQ functions no better than none at all.
-*/
-
 static struct dcon_platform_data dcon_pdata_xo_1_5;
 
 static void dcon_clear_irq(void)
 {
-       if (TEST_B2 || olpc_board_at_least(olpc_board(BOARD_XO_1_5_B3))) {
-               // irq status will appear in PMIO_Rx50[6] (RW1C) on gpio12
-               outb(BIT_GPIO12, VX855_GPI_STATUS_CHG);
-       }
+       /* irq status will appear in PMIO_Rx50[6] (RW1C) on gpio12 */
+       outb(BIT_GPIO12, VX855_GPI_STATUS_CHG);
 }
 
 static int dcon_was_irq(void)
 {
        u_int8_t tmp;
 
-       if (TEST_B2 || olpc_board_at_least(olpc_board(BOARD_XO_1_5_B3))) {
-               // irq status will appear in PMIO_Rx50[6] on gpio12
-               tmp = inb(VX855_GPI_STATUS_CHG);
-               return !!(tmp & BIT_GPIO12);
-       }
+       /* irq status will appear in PMIO_Rx50[6] on gpio12 */
+       tmp = inb(VX855_GPI_STATUS_CHG);
+       return !!(tmp & BIT_GPIO12);
 
        return 0;
 }
@@ -76,14 +59,8 @@ static int dcon_init_xo_1_5(void)
                return 1;
        }
 
-       if (olpc_board_at_least(olpc_board(BOARD_XO_1_5_B1))) {
-               pci_read_config_byte(pdev, 0x95, &tmp);
-               pci_write_config_byte(pdev, 0x95, tmp|0x0c);
-       } else {
-               /* Set GPO12 to GPO mode, not nCR_PWOFF */
-               pci_read_config_byte(pdev, 0x9b, &tmp);
-               pci_write_config_byte(pdev, 0x9b, tmp|0x01);
-       }
+       pci_read_config_byte(pdev, 0x95, &tmp);
+       pci_write_config_byte(pdev, 0x95, tmp|0x0c);
 
        /* Set GPIO8 to GPIO mode, not SSPICLK */
        pci_read_config_byte(pdev, 0xe3, &tmp);
@@ -93,31 +70,22 @@ static int dcon_init_xo_1_5(void)
        pci_read_config_byte(pdev, 0xe4, &tmp);
        pci_write_config_byte(pdev, 0xe4, tmp|0x08);
 
-       if (TEST_B2 || olpc_board_at_least(olpc_board(BOARD_XO_1_5_B3))) {
-               // clear PMU_RxE1[6] to select SCI on GPIO12
-               // clear PMU_RxE0[6] to choose falling edge
-               pci_read_config_byte(pdev, 0xe1, &tmp);
-               pci_write_config_byte(pdev, 0xe1, tmp & ~BIT_GPIO12);
-               pci_read_config_byte(pdev, 0xe0, &tmp);
-               pci_write_config_byte(pdev, 0xe0, tmp & ~BIT_GPIO12);
-
-               dcon_clear_irq();
+       /* clear PMU_RxE1[6] to select SCI on GPIO12 */
+       /* clear PMU_RxE0[6] to choose falling edge */
+       pci_read_config_byte(pdev, 0xe1, &tmp);
+       pci_write_config_byte(pdev, 0xe1, tmp & ~BIT_GPIO12);
+       pci_read_config_byte(pdev, 0xe0, &tmp);
+       pci_write_config_byte(pdev, 0xe0, tmp & ~BIT_GPIO12);
 
-               // set   PMIO_Rx52[6] to enable SCI/SMI on gpio12
-               outb(inb(VX855_GPI_SCI_SMI)|BIT_GPIO12, VX855_GPI_SCI_SMI);
+       dcon_clear_irq();
 
-       }
+       /* set   PMIO_Rx52[6] to enable SCI/SMI on gpio12 */
+       outb(inb(VX855_GPI_SCI_SMI)|BIT_GPIO12, VX855_GPI_SCI_SMI);
 
        /* Determine the current state of DCONLOAD, likely set by firmware */
-       if (olpc_board_at_least(olpc_board(BOARD_XO_1_5_B1))) {
-               // GPIO1
-               dcon_source = (inl(VX855_GENL_PURPOSE_OUTPUT) & 0x1000) ?
-                       DCON_SOURCE_CPU : DCON_SOURCE_DCON;
-       } else {
-               // GPO12
-               dcon_source = (inl(VX855_GENL_PURPOSE_OUTPUT) & 0x04000000) ?
+       /* GPIO1 */
+       dcon_source = (inl(VX855_GENL_PURPOSE_OUTPUT) & 0x1000) ?
                        DCON_SOURCE_CPU : DCON_SOURCE_DCON;
-       }
        dcon_pending = dcon_source;
 
        pci_dev_put(pdev);
@@ -180,19 +148,13 @@ static void dcon_wiggle_xo_1_5(void)
        }
        udelay(5);
 
-       if (TEST_B2 || olpc_board_at_least(olpc_board(BOARD_XO_1_5_B3))) {
-               // set   PMIO_Rx52[6] to enable SCI/SMI on gpio12
-               outb(inb(VX855_GPI_SCI_SMI)|BIT_GPIO12, VX855_GPI_SCI_SMI);
-       }
+       /* set   PMIO_Rx52[6] to enable SCI/SMI on gpio12 */
+       outb(inb(VX855_GPI_SCI_SMI)|BIT_GPIO12, VX855_GPI_SCI_SMI);
 }
 
 static void dcon_set_dconload_xo_1_5(int val)
 {
-       if (olpc_board_at_least(olpc_board(BOARD_XO_1_5_B1))) {
-               gpio_set_value(VX855_GPIO(1), val);
-       } else {
-               gpio_set_value(VX855_GPO(12), val);
-       }
+       gpio_set_value(VX855_GPIO(1), val);
 }
 
 static u8 dcon_read_status_xo_1_5(void)