Freescale i.MX Platforms Device Tree Bindings
-----------------------------------------------
+i.MX23 Evaluation Kit
+Required root node properties:
+ - compatible = "fsl,imx23-evk", "fsl,imx23";
+
+i.MX28 Evaluation Kit
+Required root node properties:
+ - compatible = "fsl,imx28-evk", "fsl,imx28";
+
i.MX51 Babbage Board
Required root node properties:
- compatible = "fsl,imx51-babbage", "fsl,imx51";
Required root node properties:
- compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+i.MX6 Quad SABRE Smart Device Board
+Required root node properties:
+ - compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
+
Generic i.MX boards
-------------------
--- /dev/null
+* Freescale MXS DMA
+
+Required properties:
+- compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx"
+- reg : Should contain registers location and length
+
+Supported chips:
+imx23, imx28.
+
+Examples:
+dma-apbh@80004000 {
+ compatible = "fsl,imx28-dma-apbh";
+ reg = <0x80004000 2000>;
+};
+
+dma-apbx@80024000 {
+ compatible = "fsl,imx28-dma-apbx";
+ reg = <0x80024000 2000>;
+};
--- /dev/null
+* Freescale MXS GPIO controller
+
+The Freescale MXS GPIO controller is part of MXS PIN controller. The
+GPIOs are organized in port/bank. Each port consists of 32 GPIOs.
+
+As the GPIO controller is embedded in the PIN controller and all the
+GPIO ports share the same IO space with PIN controller, the GPIO node
+will be represented as sub-nodes of MXS pinctrl node.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio". The supported SoCs include
+ imx23 and imx28.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two. The first cell is the pin number and
+ the second cell is used to specify optional parameters (currently
+ unused).
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2. The first cell is the GPIO number.
+ The second cell bits[3:0] is used to specify trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ gpio4 = &gpio4;
+};
+
+pinctrl@80018000 {
+ compatible = "fsl,imx28-pinctrl", "simple-bus";
+ reg = <0x80018000 2000>;
+
+ gpio0: gpio@0 {
+ compatible = "fsl,imx28-gpio";
+ interrupts = <127>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@1 {
+ compatible = "fsl,imx28-gpio";
+ interrupts = <126>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@2 {
+ compatible = "fsl,imx28-gpio";
+ interrupts = <125>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@3 {
+ compatible = "fsl,imx28-gpio";
+ interrupts = <124>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@4 {
+ compatible = "fsl,imx28-gpio";
+ interrupts = <123>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
--- /dev/null
+* Freescale MXS Inter IC (I2C) Controller
+
+Required properties:
+- compatible: Should be "fsl,<chip>-i2c"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+
+Examples:
+
+i2c0: i2c@80058000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-i2c";
+ reg = <0x80058000 2000>;
+ interrupts = <111 68>;
+};
--- /dev/null
+* Freescale MXS MMC controller
+
+The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller
+to support MMC, SD, and SDIO types of memory cards.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-mmc". The supported chips include
+ imx23 and imx28.
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+- fsl,ssp-dma-channel: APBH DMA channel for the SSP
+- bus-width: Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- wp-gpios: Specify GPIOs for write protection
+
+Examples:
+
+ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ reg = <0x80010000 2000>;
+ interrupts = <96 82>;
+ fsl,ssp-dma-channel = <0>;
+ bus-width = <8>;
+};
Example:
-fec@83fec000 {
+ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
Example:
-uart@73fbc000 {
+serial@73fbc000 {
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
reg = <0x73fbc000 0x4000>;
interrupts = <31>;
select COMMON_CLK
select HAVE_CLK_PREPARE
select PINCTRL
+ select USE_OF
help
Support for Freescale MXS-based family of processors
Say Y here if you want kernel low-level debugging support
on i.MX50 or i.MX53.
+ config DEBUG_IMX6Q_UART2
+ bool "i.MX6Q Debug UART2"
+ depends on SOC_IMX6Q
+ help
+ Say Y here if you want kernel low-level debugging support
+ on i.MX6Q UART2. This is correct for e.g. the SabreLite
+ board.
+
config DEBUG_IMX6Q_UART4
bool "i.MX6Q Debug UART4"
depends on SOC_IMX6Q
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx23.dtsi"
+
+/ {
+ model = "Freescale i.MX23 Evaluation Kit";
+ compatible = "fsl,imx23-evk", "fsl,imx23";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx23-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a &mmc0_pins_fixup>;
+ bus-width = <8>;
+ wp-gpios = <&gpio1 30 0>;
+ status = "okay";
+ };
+ };
+
+ apbx@80040000 {
+ duart: serial@80070000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ interrupt-parent = <&icoll>;
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ };
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,arm926ejs";
+ };
+ };
+
+ apb@80000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80000000 0x80000>;
+ ranges;
+
+ apbh@80000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80000000 0x40000>;
+ ranges;
+
+ icoll: interrupt-controller@80000000 {
+ compatible = "fsl,imx23-icoll", "fsl,mxs-icoll";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x80000000 0x2000>;
+ };
+
+ dma-apbh@80004000 {
+ compatible = "fsl,imx23-dma-apbh";
+ reg = <0x80004000 2000>;
+ };
+
+ ecc@80008000 {
+ reg = <0x80008000 2000>;
+ status = "disabled";
+ };
+
+ bch@8000a000 {
+ reg = <0x8000a000 2000>;
+ status = "disabled";
+ };
+
+ gpmi@8000c000 {
+ reg = <0x8000c000 2000>;
+ status = "disabled";
+ };
+
+ ssp0: ssp@80010000 {
+ reg = <0x80010000 2000>;
+ interrupts = <15 14>;
+ fsl,ssp-dma-channel = <1>;
+ status = "disabled";
+ };
+
+ etm@80014000 {
+ reg = <0x80014000 2000>;
+ status = "disabled";
+ };
+
+ pinctrl@80018000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx23-pinctrl", "simple-bus";
+ reg = <0x80018000 2000>;
+
+ gpio0: gpio@0 {
+ compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+ interrupts = <16>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@1 {
+ compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+ interrupts = <17>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@2 {
+ compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+ interrupts = <18>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ duart_pins_a: duart@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x11a2 0x11b2>;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ mmc0_8bit_pins_a: mmc0-8bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x2020 0x2030 0x2040
+ 0x2050 0x0082 0x0092 0x00a2
+ 0x00b2 0x2000 0x2010 0x2060>;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ mmc0_pins_fixup: mmc0-pins-fixup {
+ fsl,pinmux-ids = <0x2010 0x2060>;
+ fsl,pull-up = <0>;
+ };
+ };
+
+ digctl@8001c000 {
+ reg = <0x8001c000 2000>;
+ status = "disabled";
+ };
+
+ emi@80020000 {
+ reg = <0x80020000 2000>;
+ status = "disabled";
+ };
+
+ dma-apbx@80024000 {
+ compatible = "fsl,imx23-dma-apbx";
+ reg = <0x80024000 2000>;
+ };
+
+ dcp@80028000 {
+ reg = <0x80028000 2000>;
+ status = "disabled";
+ };
+
+ pxp@8002a000 {
+ reg = <0x8002a000 2000>;
+ status = "disabled";
+ };
+
+ ocotp@8002c000 {
+ reg = <0x8002c000 2000>;
+ status = "disabled";
+ };
+
+ axi-ahb@8002e000 {
+ reg = <0x8002e000 2000>;
+ status = "disabled";
+ };
+
+ lcdif@80030000 {
+ reg = <0x80030000 2000>;
+ status = "disabled";
+ };
+
+ ssp1: ssp@80034000 {
+ reg = <0x80034000 2000>;
+ interrupts = <2 20>;
+ fsl,ssp-dma-channel = <2>;
+ status = "disabled";
+ };
+
+ tvenc@80038000 {
+ reg = <0x80038000 2000>;
+ status = "disabled";
+ };
+ };
+
+ apbx@80040000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80040000 0x40000>;
+ ranges;
+
+ clkctl@80040000 {
+ reg = <0x80040000 2000>;
+ status = "disabled";
+ };
+
+ saif0: saif@80042000 {
+ reg = <0x80042000 2000>;
+ status = "disabled";
+ };
+
+ power@80044000 {
+ reg = <0x80044000 2000>;
+ status = "disabled";
+ };
+
+ saif1: saif@80046000 {
+ reg = <0x80046000 2000>;
+ status = "disabled";
+ };
+
+ audio-out@80048000 {
+ reg = <0x80048000 2000>;
+ status = "disabled";
+ };
+
+ audio-in@8004c000 {
+ reg = <0x8004c000 2000>;
+ status = "disabled";
+ };
+
+ lradc@80050000 {
+ reg = <0x80050000 2000>;
+ status = "disabled";
+ };
+
+ spdif@80054000 {
+ reg = <0x80054000 2000>;
+ status = "disabled";
+ };
+
+ i2c@80058000 {
+ reg = <0x80058000 2000>;
+ status = "disabled";
+ };
+
+ rtc@8005c000 {
+ reg = <0x8005c000 2000>;
+ status = "disabled";
+ };
+
+ pwm@80064000 {
+ reg = <0x80064000 2000>;
+ status = "disabled";
+ };
+
+ timrot@80068000 {
+ reg = <0x80068000 2000>;
+ status = "disabled";
+ };
+
+ auart0: serial@8006c000 {
+ reg = <0x8006c000 0x2000>;
+ status = "disabled";
+ };
+
+ auart1: serial@8006e000 {
+ reg = <0x8006e000 0x2000>;
+ status = "disabled";
+ };
+
+ duart: serial@80070000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x80070000 0x2000>;
+ interrupts = <0>;
+ status = "disabled";
+ };
+
+ usbphy@8007c000 {
+ reg = <0x8007c000 0x2000>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80080000 0x80000>;
+ ranges;
+
+ usbctrl@80080000 {
+ reg = <0x80080000 0x10000>;
+ status = "disabled";
+ };
+ };
+};
status = "okay";
};
- uart@1000a000 {
+ serial@1000a000 {
fsl,uart-has-rtscts;
status = "okay";
};
- uart@1000b000 {
+ serial@1000b000 {
fsl,uart-has-rtscts;
status = "okay";
};
- uart@1000c000 {
+ serial@1000c000 {
fsl,uart-has-rtscts;
status = "okay";
};
- fec@1002b000 {
+ ethernet@1002b000 {
status = "okay";
};
status = "disabled";
};
- uart1: uart@1000a000 {
+ uart1: serial@1000a000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1000a000 0x1000>;
interrupts = <20>;
status = "disabled";
};
- uart2: uart@1000b000 {
+ uart2: serial@1000b000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1000b000 0x1000>;
interrupts = <19>;
status = "disabled";
};
- uart3: uart@1000c000 {
+ uart3: serial@1000c000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1000c000 0x1000>;
interrupts = <18>;
status = "disabled";
};
- uart4: uart@1000d000 {
+ uart4: serial@1000d000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1000d000 0x1000>;
interrupts = <17>;
status = "disabled";
};
- uart5: uart@1001b000 {
+ uart5: serial@1001b000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1001b000 0x1000>;
interrupts = <49>;
status = "disabled";
};
- uart6: uart@1001c000 {
+ uart6: serial@1001c000 {
compatible = "fsl,imx27-uart", "fsl,imx21-uart";
reg = <0x1001c000 0x1000>;
interrupts = <48>;
status = "disabled";
};
- fec: fec@1002b000 {
+ fec: ethernet@1002b000 {
compatible = "fsl,imx27-fec";
reg = <0x1002b000 0x4000>;
interrupts = <50>;
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx28.dtsi"
+
+/ {
+ model = "Freescale i.MX28 Evaluation Kit";
+ compatible = "fsl,imx28-evk", "fsl,imx28";
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ apb@80000000 {
+ apbh@80000000 {
+ ssp0: ssp@80010000 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio2 12 0>;
+ status = "okay";
+ };
+
+ ssp1: ssp@80012000 {
+ compatible = "fsl,imx28-mmc";
+ bus-width = <8>;
+ wp-gpios = <&gpio0 28 0>;
+ status = "okay";
+ };
+ };
+
+ apbx@80040000 {
+ saif0: saif@80042000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+ };
+
+ saif1: saif@80046000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+ };
+
+ i2c0: i2c@80058000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+
+ };
+ };
+
+ duart: serial@80074000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ mac0: ethernet@800f0000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ status = "okay";
+ };
+
+ mac1: ethernet@800f4000 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx28-evk-sgtl5000",
+ "fsl,mxs-audio-sgtl5000";
+ model = "imx28-evk-sgtl5000";
+ saif-controllers = <&saif0 &saif1>;
+ audio-codec = <&sgtl5000>;
+ };
+};
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ interrupt-parent = <&icoll>;
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ gpio3 = &gpio3;
+ gpio4 = &gpio4;
+ saif0 = &saif0;
+ saif1 = &saif1;
+ };
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,arm926ejs";
+ };
+ };
+
+ apb@80000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80000000 0x80000>;
+ ranges;
+
+ apbh@80000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80000000 0x3c900>;
+ ranges;
+
+ icoll: interrupt-controller@80000000 {
+ compatible = "fsl,imx28-icoll", "fsl,mxs-icoll";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x80000000 0x2000>;
+ };
+
+ hsadc@80002000 {
+ reg = <0x80002000 2000>;
+ interrupts = <13 87>;
+ status = "disabled";
+ };
+
+ dma-apbh@80004000 {
+ compatible = "fsl,imx28-dma-apbh";
+ reg = <0x80004000 2000>;
+ };
+
+ perfmon@80006000 {
+ reg = <0x80006000 800>;
+ interrupts = <27>;
+ status = "disabled";
+ };
+
+ bch@8000a000 {
+ reg = <0x8000a000 2000>;
+ interrupts = <41>;
+ status = "disabled";
+ };
+
+ gpmi@8000c000 {
+ reg = <0x8000c000 2000>;
+ interrupts = <42 88>;
+ status = "disabled";
+ };
+
+ ssp0: ssp@80010000 {
+ reg = <0x80010000 2000>;
+ interrupts = <96 82>;
+ fsl,ssp-dma-channel = <0>;
+ status = "disabled";
+ };
+
+ ssp1: ssp@80012000 {
+ reg = <0x80012000 2000>;
+ interrupts = <97 83>;
+ fsl,ssp-dma-channel = <1>;
+ status = "disabled";
+ };
+
+ ssp2: ssp@80014000 {
+ reg = <0x80014000 2000>;
+ interrupts = <98 84>;
+ fsl,ssp-dma-channel = <2>;
+ status = "disabled";
+ };
+
+ ssp3: ssp@80016000 {
+ reg = <0x80016000 2000>;
+ interrupts = <99 85>;
+ fsl,ssp-dma-channel = <3>;
+ status = "disabled";
+ };
+
+ pinctrl@80018000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-pinctrl", "simple-bus";
+ reg = <0x80018000 2000>;
+
+ gpio0: gpio@0 {
+ compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ interrupts = <127>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@1 {
+ compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ interrupts = <126>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@2 {
+ compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ interrupts = <125>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@3 {
+ compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ interrupts = <124>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@4 {
+ compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+ interrupts = <123>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ duart_pins_a: duart@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x3102 0x3112>;
+ fsl,drive-strength = <0>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <0>;
+ };
+
+ mac0_pins_a: mac0@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x4000 0x4010 0x4020
+ 0x4030 0x4040 0x4060 0x4070
+ 0x4080 0x4100>;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ mac1_pins_a: mac1@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x40f1 0x4091 0x40a1
+ 0x40e1 0x40b1 0x40c1>;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ mmc0_8bit_pins_a: mmc0-8bit@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x2000 0x2010 0x2020
+ 0x2030 0x2040 0x2050 0x2060
+ 0x2070 0x2080 0x2090 0x20a0>;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ mmc0_cd_cfg: mmc0-cd-cfg {
+ fsl,pinmux-ids = <0x2090>;
+ fsl,pull-up = <0>;
+ };
+
+ mmc0_sck_cfg: mmc0-sck-cfg {
+ fsl,pinmux-ids = <0x20a0>;
+ fsl,drive-strength = <2>;
+ fsl,pull-up = <0>;
+ };
+
+ i2c0_pins_a: i2c0@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x3180 0x3190>;
+ fsl,drive-strength = <1>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ saif0_pins_a: saif0@0 {
+ reg = <0>;
+ fsl,pinmux-ids =
+ <0x3140 0x3150 0x3160 0x3170>;
+ fsl,drive-strength = <2>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+
+ saif1_pins_a: saif1@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <0x31a0>;
+ fsl,drive-strength = <2>;
+ fsl,voltage = <1>;
+ fsl,pull-up = <1>;
+ };
+ };
+
+ digctl@8001c000 {
+ reg = <0x8001c000 2000>;
+ interrupts = <89>;
+ status = "disabled";
+ };
+
+ etm@80022000 {
+ reg = <0x80022000 2000>;
+ status = "disabled";
+ };
+
+ dma-apbx@80024000 {
+ compatible = "fsl,imx28-dma-apbx";
+ reg = <0x80024000 2000>;
+ };
+
+ dcp@80028000 {
+ reg = <0x80028000 2000>;
+ interrupts = <52 53 54>;
+ status = "disabled";
+ };
+
+ pxp@8002a000 {
+ reg = <0x8002a000 2000>;
+ interrupts = <39>;
+ status = "disabled";
+ };
+
+ ocotp@8002c000 {
+ reg = <0x8002c000 2000>;
+ status = "disabled";
+ };
+
+ axi-ahb@8002e000 {
+ reg = <0x8002e000 2000>;
+ status = "disabled";
+ };
+
+ lcdif@80030000 {
+ reg = <0x80030000 2000>;
+ interrupts = <38 86>;
+ status = "disabled";
+ };
+
+ can0: can@80032000 {
+ reg = <0x80032000 2000>;
+ interrupts = <8>;
+ status = "disabled";
+ };
+
+ can1: can@80034000 {
+ reg = <0x80034000 2000>;
+ interrupts = <9>;
+ status = "disabled";
+ };
+
+ simdbg@8003c000 {
+ reg = <0x8003c000 200>;
+ status = "disabled";
+ };
+
+ simgpmisel@8003c200 {
+ reg = <0x8003c200 100>;
+ status = "disabled";
+ };
+
+ simsspsel@8003c300 {
+ reg = <0x8003c300 100>;
+ status = "disabled";
+ };
+
+ simmemsel@8003c400 {
+ reg = <0x8003c400 100>;
+ status = "disabled";
+ };
+
+ gpiomon@8003c500 {
+ reg = <0x8003c500 100>;
+ status = "disabled";
+ };
+
+ simenet@8003c700 {
+ reg = <0x8003c700 100>;
+ status = "disabled";
+ };
+
+ armjtag@8003c800 {
+ reg = <0x8003c800 100>;
+ status = "disabled";
+ };
+ };
+
+ apbx@80040000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80040000 0x40000>;
+ ranges;
+
+ clkctl@80040000 {
+ reg = <0x80040000 2000>;
+ status = "disabled";
+ };
+
+ saif0: saif@80042000 {
+ compatible = "fsl,imx28-saif";
+ reg = <0x80042000 2000>;
+ interrupts = <59 80>;
+ fsl,saif-dma-channel = <4>;
+ status = "disabled";
+ };
+
+ power@80044000 {
+ reg = <0x80044000 2000>;
+ status = "disabled";
+ };
+
+ saif1: saif@80046000 {
+ compatible = "fsl,imx28-saif";
+ reg = <0x80046000 2000>;
+ interrupts = <58 81>;
+ fsl,saif-dma-channel = <5>;
+ status = "disabled";
+ };
+
+ lradc@80050000 {
+ reg = <0x80050000 2000>;
+ status = "disabled";
+ };
+
+ spdif@80054000 {
+ reg = <0x80054000 2000>;
+ interrupts = <45 66>;
+ status = "disabled";
+ };
+
+ rtc@80056000 {
+ reg = <0x80056000 2000>;
+ interrupts = <28 29>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@80058000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-i2c";
+ reg = <0x80058000 2000>;
+ interrupts = <111 68>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@8005a000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-i2c";
+ reg = <0x8005a000 2000>;
+ interrupts = <110 69>;
+ status = "disabled";
+ };
+
+ pwm@80064000 {
+ reg = <0x80064000 2000>;
+ status = "disabled";
+ };
+
+ timrot@80068000 {
+ reg = <0x80068000 2000>;
+ status = "disabled";
+ };
+
+ auart0: serial@8006a000 {
+ reg = <0x8006a000 0x2000>;
+ interrupts = <112 70 71>;
+ status = "disabled";
+ };
+
+ auart1: serial@8006c000 {
+ reg = <0x8006c000 0x2000>;
+ interrupts = <113 72 73>;
+ status = "disabled";
+ };
+
+ auart2: serial@8006e000 {
+ reg = <0x8006e000 0x2000>;
+ interrupts = <114 74 75>;
+ status = "disabled";
+ };
+
+ auart3: serial@80070000 {
+ reg = <0x80070000 0x2000>;
+ interrupts = <115 76 77>;
+ status = "disabled";
+ };
+
+ auart4: serial@80072000 {
+ reg = <0x80072000 0x2000>;
+ interrupts = <116 78 79>;
+ status = "disabled";
+ };
+
+ duart: serial@80074000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x80074000 0x1000>;
+ interrupts = <47>;
+ status = "disabled";
+ };
+
+ usbphy0: usbphy@8007c000 {
+ reg = <0x8007c000 0x2000>;
+ status = "disabled";
+ };
+
+ usbphy1: usbphy@8007e000 {
+ reg = <0x8007e000 0x2000>;
+ status = "disabled";
+ };
+ };
+ };
+
+ ahb@80080000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x80080000 0x80000>;
+ ranges;
+
+ usbctrl0: usbctrl@80080000 {
+ reg = <0x80080000 0x10000>;
+ status = "disabled";
+ };
+
+ usbctrl1: usbctrl@80090000 {
+ reg = <0x80090000 0x10000>;
+ status = "disabled";
+ };
+
+ dflpt@800c0000 {
+ reg = <0x800c0000 0x10000>;
+ status = "disabled";
+ };
+
+ mac0: ethernet@800f0000 {
+ compatible = "fsl,imx28-fec";
+ reg = <0x800f0000 0x4000>;
+ interrupts = <101>;
+ status = "disabled";
+ };
+
+ mac1: ethernet@800f4000 {
+ compatible = "fsl,imx28-fec";
+ reg = <0x800f4000 0x4000>;
+ interrupts = <102>;
+ status = "disabled";
+ };
+
+ switch@800f8000 {
+ reg = <0x800f8000 0x8000>;
+ status = "disabled";
+ };
+
+ };
+};
model = "Freescale i.MX51 Babbage Board";
compatible = "fsl,imx51-babbage", "fsl,imx51";
- chosen {
- bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
- };
-
memory {
reg = <0x90000000 0x20000000>;
};
status = "okay";
};
- uart3: uart@7000c000 {
+ uart3: serial@7000c000 {
fsl,uart-has-rtscts;
status = "okay";
};
};
};
};
+
+ ssi2: ssi@70014000 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+ };
};
wdog@73f98000 { /* WDOG1 */
reg = <0x73fa8000 0x4000>;
};
- uart1: uart@73fbc000 {
+ uart1: serial@73fbc000 {
fsl,uart-has-rtscts;
status = "okay";
};
- uart2: uart@73fc0000 {
+ uart2: serial@73fc0000 {
status = "okay";
};
};
i2c@83fc4000 { /* I2C2 */
status = "okay";
- codec: sgtl5000@0a {
+ sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
+ clock-frequency = <26000000>;
+ VDDA-supply = <&vdig_reg>;
+ VDDIO-supply = <&vvideo_reg>;
};
};
- fec@83fec000 {
+ audmux@83fd0000 {
+ status = "okay";
+ };
+
+ ethernet@83fec000 {
phy-mode = "mii";
status = "okay";
};
gpio-key,wakeup;
};
};
+
+ sound {
+ compatible = "fsl,imx51-babbage-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx51-babbage-sgtl5000";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <2>;
+ mux-ext-port = <3>;
+ };
};
status = "disabled";
};
- uart3: uart@7000c000 {
+ uart3: serial@7000c000 {
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
reg = <0x7000c000 0x4000>;
interrupts = <33>;
status = "disabled";
};
+ ssi2: ssi@70014000 {
+ compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+ reg = <0x70014000 0x4000>;
+ interrupts = <30>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <25 24 23 22>; /* TX0 RX0 TX1 RX1 */
+ status = "disabled";
+ };
+
esdhc@70020000 { /* ESDHC3 */
compatible = "fsl,imx51-esdhc";
reg = <0x70020000 0x4000>;
status = "disabled";
};
- uart1: uart@73fbc000 {
+ uart1: serial@73fbc000 {
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
reg = <0x73fbc000 0x4000>;
interrupts = <31>;
status = "disabled";
};
- uart2: uart@73fc0000 {
+ uart2: serial@73fc0000 {
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
reg = <0x73fc0000 0x4000>;
interrupts = <32>;
status = "disabled";
};
- fec@83fec000 {
+ ssi1: ssi@83fcc000 {
+ compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+ reg = <0x83fcc000 0x4000>;
+ interrupts = <29>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <29 28 27 26>; /* TX0 RX0 TX1 RX1 */
+ status = "disabled";
+ };
+
+ audmux@83fd0000 {
+ compatible = "fsl,imx51-audmux", "fsl,imx31-audmux";
+ reg = <0x83fd0000 0x4000>;
+ status = "disabled";
+ };
+
+ ssi3: ssi@83fe8000 {
+ compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+ reg = <0x83fe8000 0x4000>;
+ interrupts = <96>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <47 46 37 35>; /* TX0 RX0 TX1 RX1 */
+ status = "disabled";
+ };
+
+ ethernet@83fec000 {
compatible = "fsl,imx51-fec", "fsl,imx27-fec";
reg = <0x83fec000 0x4000>;
interrupts = <87>;
model = "Freescale i.MX53 Automotive Reference Design Board";
compatible = "fsl,imx53-ard", "fsl,imx53";
- chosen {
- bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
- };
-
memory {
reg = <0x70000000 0x40000000>;
};
reg = <0x53fa8000 0x4000>;
};
- uart1: uart@53fbc000 {
+ uart1: serial@53fbc000 {
status = "okay";
};
};
model = "Freescale i.MX53 Evaluation Kit";
compatible = "fsl,imx53-evk", "fsl,imx53";
- chosen {
- bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
- };
-
memory {
reg = <0x70000000 0x80000000>;
};
reg = <0x53fa8000 0x4000>;
};
- uart1: uart@53fbc000 {
+ uart1: serial@53fbc000 {
status = "okay";
};
};
};
};
- fec@63fec000 {
+ ethernet@63fec000 {
phy-mode = "rmii";
phy-reset-gpios = <&gpio7 6 0>;
status = "okay";
model = "Freescale i.MX53 Quick Start Board";
compatible = "fsl,imx53-qsb", "fsl,imx53";
- chosen {
- bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
- };
-
memory {
reg = <0x70000000 0x40000000>;
};
status = "okay";
};
+ ssi2: ssi@50014000 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+ };
+
esdhc@50020000 { /* ESDHC3 */
cd-gpios = <&gpio3 11 0>;
wp-gpios = <&gpio3 12 0>;
reg = <0x53fa8000 0x4000>;
};
- uart1: uart@53fbc000 {
+ uart1: serial@53fbc000 {
status = "okay";
};
};
i2c@63fc4000 { /* I2C2 */
status = "okay";
- codec: sgtl5000@0a {
+ sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
+ VDDA-supply = <®_3p2v>;
+ VDDIO-supply = <®_3p2v>;
};
};
};
pmic: dialog@48 {
- compatible = "dialog,da9053", "dialog,da9052";
+ compatible = "dlg,da9053-aa", "dlg,da9052";
reg = <0x48>;
+
+ regulators {
+ buck0 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2075000>;
+ };
+
+ buck1 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2075000>;
+ };
+
+ buck2 {
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ buck3 {
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ ldo4 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo5 {
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo6 {
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo7 {
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo9 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo10 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo11 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo12 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3650000>;
+ };
+
+ ldo13 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ };
+ };
};
};
- fec@63fec000 {
+ audmux@63fd0000 {
+ status = "okay";
+ };
+
+ ethernet@63fec000 {
phy-mode = "rmii";
phy-reset-gpios = <&gpio7 6 0>;
status = "okay";
linux,default-trigger = "heartbeat";
};
};
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_3p2v: 3p2v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P2V";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-always-on;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx53-qsb-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx53-qsb-sgtl5000";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <2>;
+ mux-ext-port = <5>;
+ };
};
model = "Freescale i.MX53 Smart Mobile Reference Design Board";
compatible = "fsl,imx53-smd", "fsl,imx53";
- chosen {
- bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
- };
-
memory {
reg = <0x70000000 0x40000000>;
};
status = "okay";
};
- uart3: uart@5000c000 {
+ uart3: serial@5000c000 {
fsl,uart-has-rtscts;
status = "okay";
};
reg = <0x53fa8000 0x4000>;
};
- uart1: uart@53fbc000 {
+ uart1: serial@53fbc000 {
status = "okay";
};
- uart2: uart@53fc0000 {
+ uart2: serial@53fc0000 {
status = "okay";
};
};
};
};
- fec@63fec000 {
+ ethernet@63fec000 {
phy-mode = "rmii";
phy-reset-gpios = <&gpio7 6 0>;
status = "okay";
status = "disabled";
};
- uart3: uart@5000c000 {
+ uart3: serial@5000c000 {
compatible = "fsl,imx53-uart", "fsl,imx21-uart";
reg = <0x5000c000 0x4000>;
interrupts = <33>;
status = "disabled";
};
+ ssi2: ssi@50014000 {
+ compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
+ reg = <0x50014000 0x4000>;
+ interrupts = <30>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <25 24 23 22>; /* TX0 RX0 TX1 RX1 */
+ status = "disabled";
+ };
+
esdhc@50020000 { /* ESDHC3 */
compatible = "fsl,imx53-esdhc";
reg = <0x50020000 0x4000>;
status = "disabled";
};
- uart1: uart@53fbc000 {
+ uart1: serial@53fbc000 {
compatible = "fsl,imx53-uart", "fsl,imx21-uart";
reg = <0x53fbc000 0x4000>;
interrupts = <31>;
status = "disabled";
};
- uart2: uart@53fc0000 {
+ uart2: serial@53fc0000 {
compatible = "fsl,imx53-uart", "fsl,imx21-uart";
reg = <0x53fc0000 0x4000>;
interrupts = <32>;
status = "disabled";
};
- uart4: uart@53ff0000 {
+ uart4: serial@53ff0000 {
compatible = "fsl,imx53-uart", "fsl,imx21-uart";
reg = <0x53ff0000 0x4000>;
interrupts = <13>;
reg = <0x60000000 0x10000000>;
ranges;
- uart5: uart@63f90000 {
+ uart5: serial@63f90000 {
compatible = "fsl,imx53-uart", "fsl,imx21-uart";
reg = <0x63f90000 0x4000>;
interrupts = <86>;
status = "disabled";
};
- fec@63fec000 {
+ ssi1: ssi@63fcc000 {
+ compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
+ reg = <0x63fcc000 0x4000>;
+ interrupts = <29>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <29 28 27 26>; /* TX0 RX0 TX1 RX1 */
+ status = "disabled";
+ };
+
+ audmux@63fd0000 {
+ compatible = "fsl,imx53-audmux", "fsl,imx31-audmux";
+ reg = <0x63fd0000 0x4000>;
+ status = "disabled";
+ };
+
+ ssi3: ssi@63fe8000 {
+ compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
+ reg = <0x63fe8000 0x4000>;
+ interrupts = <96>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <47 46 45 44>; /* TX0 RX0 TX1 RX1 */
+ status = "disabled";
+ };
+
+ ethernet@63fec000 {
compatible = "fsl,imx53-fec", "fsl,imx25-fec";
reg = <0x63fec000 0x4000>;
interrupts = <87>;
model = "Freescale i.MX6 Quad Armadillo2 Board";
compatible = "fsl,imx6q-arm2", "fsl,imx6q";
- chosen {
- bootargs = "console=ttymxc0,115200 root=/dev/mmcblk3p3 rootwait";
- };
-
memory {
reg = <0x10000000 0x80000000>;
};
soc {
aips-bus@02100000 { /* AIPS2 */
- enet@02188000 {
+ ethernet@02188000 {
phy-mode = "rgmii";
- local-mac-address = [00 04 9F 01 1B 61];
status = "okay";
};
cd-gpios = <&gpio6 11 0>;
wp-gpios = <&gpio6 14 0>;
vmmc-supply = <®_3p3v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3_1>;
status = "okay";
};
usdhc@0219c000 { /* uSDHC4 */
non-removable;
vmmc-supply = <®_3p3v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4_1>;
status = "okay";
};
- uart4: uart@021f0000 {
+ uart4: serial@021f0000 {
status = "okay";
};
};
};
soc {
+ aips-bus@02000000 { /* AIPS1 */
+ spba-bus@02000000 {
+ ecspi@02008000 { /* eCSPI1 */
+ fsl,spi-num-chipselects = <1>;
+ cs-gpios = <&gpio3 19 0>;
+ status = "okay";
+
+ flash: m25p80@0 {
+ compatible = "sst,sst25vf016b";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+ };
+
+ ssi1: ssi@02028000 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+ };
+ };
+
+ };
+
aips-bus@02100000 { /* AIPS2 */
- enet@02188000 {
+ ethernet@02188000 {
phy-mode = "rgmii";
phy-reset-gpios = <&gpio3 23 0>;
status = "okay";
status = "okay";
};
- uart2: uart@021e8000 {
+ audmux@021d8000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux_1>;
+ };
+
+ uart2: serial@021e8000 {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_serial2_1>;
};
i2c@021a0000 { /* I2C1 */
status = "okay";
clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_1>;
codec: sgtl5000@0a {
compatible = "fsl,sgtl5000";
regulator-always-on;
};
};
+
+ sound {
+ compatible = "fsl,imx6q-sabrelite-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6q-sabrelite-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
+ };
};
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx6q.dtsi"
+
+/ {
+ model = "Freescale i.MX6Q SABRE Smart Device Board";
+ compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ soc {
+
+ aips-bus@02000000 { /* AIPS1 */
+ spba-bus@02000000 {
+ uart1: serial@02020000 {
+ status = "okay";
+ };
+ };
+ };
+
+ aips-bus@02100000 { /* AIPS2 */
+ ethernet@02188000 {
+ phy-mode = "rgmii";
+ status = "okay";
+ };
+
+ usdhc@02194000 { /* uSDHC2 */
+ cd-gpios = <&gpio2 2 0>;
+ wp-gpios = <&gpio2 3 0>;
+ status = "okay";
+ };
+
+ usdhc@02198000 { /* uSDHC3 */
+ cd-gpios = <&gpio2 0 0>;
+ wp-gpios = <&gpio2 1 0>;
+ status = "okay";
+ };
+ };
+ };
+};
status = "disabled";
};
- uart1: uart@02020000 {
+ uart1: serial@02020000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x02020000 0x4000>;
interrupts = <0 26 0x04>;
interrupts = <0 51 0x04>;
};
- ssi@02028000 { /* SSI1 */
+ ssi1: ssi@02028000 {
+ compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
reg = <0x02028000 0x4000>;
interrupts = <0 46 0x04>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <38 37>;
+ status = "disabled";
};
- ssi@0202c000 { /* SSI2 */
+ ssi2: ssi@0202c000 {
+ compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
reg = <0x0202c000 0x4000>;
interrupts = <0 47 0x04>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <42 41>;
+ status = "disabled";
};
- ssi@02030000 { /* SSI3 */
+ ssi3: ssi@02030000 {
+ compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
reg = <0x02030000 0x4000>;
interrupts = <0 48 0x04>;
+ fsl,fifo-depth = <15>;
+ fsl,ssi-dma-events = <46 45>;
+ status = "disabled";
};
asrc@02034000 {
compatible = "fsl,imx6q-anatop";
reg = <0x020c8000 0x1000>;
interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>;
+
+ regulator-1p1@110 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd1p1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1375000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x110>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <4>;
+ anatop-min-voltage = <800000>;
+ anatop-max-voltage = <1375000>;
+ };
+
+ regulator-3p0@120 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd3p0";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x120>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2625000>;
+ anatop-max-voltage = <3400000>;
+ };
+
+ regulator-2p5@130 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd2p5";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2750000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x130>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2000000>;
+ anatop-max-voltage = <2750000>;
+ };
+
+ regulator-vddcore@140 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "cpu";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <0>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ regulator-vddpu@140 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddpu";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <9>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ regulator-vddsoc@140 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddsoc";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <18>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
};
usbphy@020c9000 { /* USBPHY1 */
};
iomuxc@020e0000 {
+ compatible = "fsl,imx6q-iomuxc";
reg = <0x020e0000 0x4000>;
+
+ /* shared pinctrl settings */
+ audmux {
+ pinctrl_audmux_1: audmux-1 {
+ fsl,pins = <18 0x80000000 /* MX6Q_PAD_SD2_DAT0__AUDMUX_AUD4_RXD */
+ 1586 0x80000000 /* MX6Q_PAD_SD2_DAT3__AUDMUX_AUD4_TXC */
+ 11 0x80000000 /* MX6Q_PAD_SD2_DAT2__AUDMUX_AUD4_TXD */
+ 3 0x80000000>; /* MX6Q_PAD_SD2_DAT1__AUDMUX_AUD4_TXFS */
+ };
+ };
+
+ i2c1 {
+ pinctrl_i2c1_1: i2c1grp-1 {
+ fsl,pins = <137 0x4001b8b1 /* MX6Q_PAD_EIM_D21__I2C1_SCL */
+ 196 0x4001b8b1>; /* MX6Q_PAD_EIM_D28__I2C1_SDA */
+ };
+ };
+
+ serial2 {
+ pinctrl_serial2_1: serial2grp-1 {
+ fsl,pins = <183 0x1b0b1 /* MX6Q_PAD_EIM_D26__UART2_TXD */
+ 191 0x1b0b1>; /* MX6Q_PAD_EIM_D27__UART2_RXD */
+ };
+ };
+
+ usdhc3 {
+ pinctrl_usdhc3_1: usdhc3grp-1 {
+ fsl,pins = <1273 0x17059 /* MX6Q_PAD_SD3_CMD__USDHC3_CMD */
+ 1281 0x10059 /* MX6Q_PAD_SD3_CLK__USDHC3_CLK */
+ 1289 0x17059 /* MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 */
+ 1297 0x17059 /* MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 */
+ 1305 0x17059 /* MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 */
+ 1312 0x17059 /* MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 */
+ 1265 0x17059 /* MX6Q_PAD_SD3_DAT4__USDHC3_DAT4 */
+ 1257 0x17059 /* MX6Q_PAD_SD3_DAT5__USDHC3_DAT5 */
+ 1249 0x17059 /* MX6Q_PAD_SD3_DAT6__USDHC3_DAT6 */
+ 1241 0x17059>; /* MX6Q_PAD_SD3_DAT7__USDHC3_DAT7 */
+ };
+ };
+
+ usdhc4 {
+ pinctrl_usdhc4_1: usdhc4grp-1 {
+ fsl,pins = <1386 0x17059 /* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
+ 1392 0x10059 /* MX6Q_PAD_SD4_CLK__USDHC4_CLK */
+ 1462 0x17059 /* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
+ 1470 0x17059 /* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
+ 1478 0x17059 /* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
+ 1486 0x17059 /* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
+ 1493 0x17059 /* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */
+ 1501 0x17059 /* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */
+ 1509 0x17059 /* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */
+ 1517 0x17059>; /* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */
+ };
+ };
};
dcic@020e4000 { /* DCIC1 */
reg = <0x0217c000 0x4000>;
};
- enet@02188000 {
+ ethernet@02188000 {
compatible = "fsl,imx6q-fec";
reg = <0x02188000 0x4000>;
interrupts = <0 118 0x04 0 119 0x04>;
};
audmux@021d8000 {
+ compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
reg = <0x021d8000 0x4000>;
+ status = "disabled";
};
mipi@021dc000 { /* MIPI-CSI */
interrupts = <0 18 0x04>;
};
- uart2: uart@021e8000 {
+ uart2: serial@021e8000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021e8000 0x4000>;
interrupts = <0 27 0x04>;
status = "disabled";
};
- uart3: uart@021ec000 {
+ uart3: serial@021ec000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021ec000 0x4000>;
interrupts = <0 28 0x04>;
status = "disabled";
};
- uart4: uart@021f0000 {
+ uart4: serial@021f0000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021f0000 0x4000>;
interrupts = <0 29 0x04>;
status = "disabled";
};
- uart5: uart@021f4000 {
+ uart5: serial@021f4000 {
compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
reg = <0x021f4000 0x4000>;
interrupts = <0 30 0x04>;
compatible = "nvidia,cardhu", "nvidia,tegra30";
memory {
- reg = < 0x80000000 0x40000000 >;
+ reg = <0x80000000 0x40000000>;
};
- pinmux@70000000 {
+ pinmux {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
};
serial@70006000 {
- clock-frequency = < 408000000 >;
- };
-
- serial@70006040 {
- status = "disable";
- };
-
- serial@70006200 {
- status = "disable";
- };
-
- serial@70006300 {
- status = "disable";
- };
-
- serial@70006400 {
- status = "disable";
+ status = "okay";
+ clock-frequency = <408000000>;
};
i2c@7000c000 {
+ status = "okay";
clock-frequency = <100000>;
};
i2c@7000c400 {
+ status = "okay";
clock-frequency = <100000>;
};
i2c@7000c500 {
+ status = "okay";
clock-frequency = <100000>;
+
+ /* ALS and Proximity sensor */
+ isl29028@44 {
+ compatible = "isil,isl29028";
+ reg = <0x44>;
+ interrupt-parent = <&gpio>;
+ interrupts = <88 0x04>; /*gpio PL0 */
+ };
};
i2c@7000c700 {
+ status = "okay";
clock-frequency = <100000>;
};
i2c@7000d000 {
+ status = "okay";
clock-frequency = <100000>;
wm8903: wm8903@1a {
micdet-delay = <100>;
gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
};
+
+ tps62361 {
+ compatible = "ti,tps62361";
+ reg = <0x60>;
+
+ regulator-name = "tps62361-vout";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ ti,vsel0-state-high;
+ ti,vsel1-state-high;
+ };
+ };
+
+ ahub {
+ i2s@70080400 {
+ status = "okay";
+ };
};
sdhci@78000000 {
+ status = "okay";
cd-gpios = <&gpio 69 0>; /* gpio PI5 */
wp-gpios = <&gpio 155 0>; /* gpio PT3 */
power-gpios = <&gpio 31 0>; /* gpio PD7 */
bus-width = <4>;
};
- sdhci@78000200 {
- status = "disable";
- };
-
- sdhci@78000400 {
- status = "disable";
- };
-
- sdhci@78000400 {
+ sdhci@78000600 {
+ status = "okay";
support-8bit;
bus-width = <8>;
};
- ahub@70080000 {
- i2s@70080300 {
- status = "disable";
- };
-
- i2s@70080500 {
- status = "disable";
- };
-
- i2s@70080600 {
- status = "disable";
- };
-
- i2s@70080700 {
- status = "disable";
- };
- };
-
sound {
compatible = "nvidia,tegra-audio-wm8903-cardhu",
"nvidia,tegra-audio-wm8903";
model = "NVIDIA Tegra2 Harmony evaluation board";
compatible = "nvidia,harmony", "nvidia,tegra20";
- memory@0 {
- reg = < 0x00000000 0x40000000 >;
+ memory {
+ reg = <0x00000000 0x40000000>;
};
- pinmux@70000000 {
+ pinmux {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
};
};
- pmc@7000f400 {
- nvidia,invert-interrupt;
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006300 {
+ status = "okay";
+ clock-frequency = <216000000>;
};
i2c@7000c000 {
+ status = "okay";
clock-frequency = <400000>;
wm8903: wm8903@1a {
compatible = "wlf,wm8903";
reg = <0x1a>;
interrupt-parent = <&gpio>;
- interrupts = < 187 0x04 >;
+ interrupts = <187 0x04>;
gpio-controller;
#gpio-cells = <2>;
micdet-cfg = <0>;
micdet-delay = <100>;
- gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
};
};
i2c@7000c400 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000c500 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000d000 {
+ status = "okay";
clock-frequency = <400000>;
};
- i2s@70002a00 {
- status = "disable";
+ pmc {
+ nvidia,invert-interrupt;
+ };
+
+ usb@c5000000 {
+ status = "okay";
+ };
+
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000200 {
+ status = "okay";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 155 0>; /* gpio PT3 */
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ cd-gpios = <&gpio 58 0>; /* gpio PH2 */
+ wp-gpios = <&gpio 59 0>; /* gpio PH3 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
+ support-8bit;
+ bus-width = <8>;
};
sound {
nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
};
-
- serial@70006000 {
- status = "disable";
- };
-
- serial@70006040 {
- status = "disable";
- };
-
- serial@70006200 {
- status = "disable";
- };
-
- serial@70006300 {
- clock-frequency = < 216000000 >;
- };
-
- serial@70006400 {
- status = "disable";
- };
-
- sdhci@c8000000 {
- status = "disable";
- };
-
- sdhci@c8000200 {
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 155 0>; /* gpio PT3 */
- bus-width = <4>;
- };
-
- sdhci@c8000400 {
- status = "disable";
- };
-
- sdhci@c8000600 {
- cd-gpios = <&gpio 58 0>; /* gpio PH2 */
- wp-gpios = <&gpio 59 0>; /* gpio PH3 */
- power-gpios = <&gpio 70 0>; /* gpio PI6 */
- support-8bit;
- bus-width = <8>;
- };
-
- usb@c5004000 {
- nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
- };
};
model = "Toshiba AC100 / Dynabook AZ";
compatible = "compal,paz00", "nvidia,tegra20";
- memory@0 {
+ memory {
reg = <0x00000000 0x20000000>;
};
- pinmux@70000000 {
+ pinmux {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
};
};
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006000 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
+ serial@70006200 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
i2c@7000c000 {
+ status = "okay";
clock-frequency = <400000>;
alc5632: alc5632@1e {
};
i2c@7000c400 {
+ status = "okay";
clock-frequency = <400000>;
};
- i2c@7000c500 {
- status = "disable";
- };
-
- nvec@7000c500 {
- #address-cells = <1>;
- #size-cells = <0>;
+ nvec {
compatible = "nvidia,nvec";
- reg = <0x7000C500 0x100>;
+ reg = <0x7000c500 0x100>;
interrupts = <0 92 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
clock-frequency = <80000>;
- request-gpios = <&gpio 170 0>;
+ request-gpios = <&gpio 170 0>; /* gpio PV2 */
slave-addr = <138>;
};
i2c@7000d000 {
+ status = "okay";
clock-frequency = <400000>;
adt7461@4c {
};
};
- i2s@70002a00 {
- status = "disable";
- };
-
- sound {
- compatible = "nvidia,tegra-audio-alc5632-paz00",
- "nvidia,tegra-audio-alc5632";
-
- nvidia,model = "Compal PAZ00";
-
- nvidia,audio-routing =
- "Int Spk", "SPKOUT",
- "Int Spk", "SPKOUTN",
- "Headset Mic", "MICBIAS1",
- "MIC1", "Headset Mic",
- "Headset Stereophone", "HPR",
- "Headset Stereophone", "HPL",
- "DMICDAT", "Digital Mic";
-
- nvidia,audio-codec = <&alc5632>;
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- };
-
- serial@70006000 {
- clock-frequency = <216000000>;
- };
-
- serial@70006040 {
- status = "disable";
- };
-
- serial@70006200 {
- clock-frequency = <216000000>;
+ usb@c5000000 {
+ status = "okay";
};
- serial@70006300 {
- status = "disable";
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
};
- serial@70006400 {
- status = "disable";
+ usb@c5008000 {
+ status = "okay";
};
sdhci@c8000000 {
+ status = "okay";
cd-gpios = <&gpio 173 0>; /* gpio PV5 */
wp-gpios = <&gpio 57 0>; /* gpio PH1 */
power-gpios = <&gpio 169 0>; /* gpio PV1 */
bus-width = <4>;
};
- sdhci@c8000200 {
- status = "disable";
- };
-
- sdhci@c8000400 {
- status = "disable";
- };
-
sdhci@c8000600 {
+ status = "okay";
support-8bit;
bus-width = <8>;
};
wifi {
label = "wifi-led";
- gpios = <&gpio 24 0>;
+ gpios = <&gpio 24 0>; /* gpio PD0 */
linux,default-trigger = "rfkill0";
};
};
- usb@c5004000 {
- nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
+ sound {
+ compatible = "nvidia,tegra-audio-alc5632-paz00",
+ "nvidia,tegra-audio-alc5632";
+
+ nvidia,model = "Compal PAZ00";
+
+ nvidia,audio-routing =
+ "Int Spk", "SPKOUT",
+ "Int Spk", "SPKOUTN",
+ "Headset Mic", "MICBIAS1",
+ "MIC1", "Headset Mic",
+ "Headset Stereophone", "HPR",
+ "Headset Stereophone", "HPL",
+ "DMICDAT", "Digital Mic";
+
+ nvidia,audio-codec = <&alc5632>;
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
};
};
compatible = "nvidia,seaboard", "nvidia,tegra20";
memory {
- device_type = "memory";
- reg = < 0x00000000 0x40000000 >;
+ reg = <0x00000000 0x40000000>;
};
- pinmux@70000000 {
+ pinmux {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
};
hdint {
nvidia,pins = "hdint", "lpw0", "lpw2", "lsc1",
- "lsck", "lsda", "pta";
+ "lsck", "lsda";
nvidia,function = "hdmi";
};
i2cp {
nvidia,pins = "pmc";
nvidia,function = "pwr_on";
};
+ pta {
+ nvidia,pins = "pta";
+ nvidia,function = "i2c2";
+ };
rm {
nvidia,pins = "rm";
nvidia,function = "i2c1";
};
};
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006300 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
i2c@7000c000 {
+ status = "okay";
clock-frequency = <400000>;
wm8903: wm8903@1a {
compatible = "wlf,wm8903";
reg = <0x1a>;
interrupt-parent = <&gpio>;
- interrupts = < 187 0x04 >;
+ interrupts = <187 0x04>;
gpio-controller;
#gpio-cells = <2>;
micdet-cfg = <0>;
micdet-delay = <100>;
- gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+
+ /* ALS and proximity sensor */
+ isl29018@44 {
+ compatible = "isil,isl29018";
+ reg = <0x44>;
+ interrupt-parent = <&gpio>;
+ interrupts = <202 0x04>; /* GPIO PZ2 */
+ };
+
+ gyrometer@68 {
+ compatible = "invn,mpu3050";
+ reg = <0x68>;
+ interrupt-parent = <&gpio>;
+ interrupts = <204 0x04>; /* gpio PZ4 */
};
};
i2c@7000c400 {
- clock-frequency = <400000>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ smart-battery@b {
+ compatible = "ti,bq20z75", "smart-battery-1.1";
+ reg = <0xb>;
+ ti,i2c-retry-count = <2>;
+ ti,poll-retry-count = <10>;
+ };
};
i2c@7000c500 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000d000 {
+ status = "okay";
clock-frequency = <400000>;
- adt7461@4c {
- compatible = "adt7461";
+ temperature-sensor@4c {
+ compatible = "nct1008";
reg = <0x4c>;
};
- };
-
- i2s@70002a00 {
- status = "disable";
- };
-
- sound {
- compatible = "nvidia,tegra-audio-wm8903-seaboard",
- "nvidia,tegra-audio-wm8903";
- nvidia,model = "NVIDIA Tegra Seaboard";
-
- nvidia,audio-routing =
- "Headphone Jack", "HPOUTR",
- "Headphone Jack", "HPOUTL",
- "Int Spk", "ROP",
- "Int Spk", "RON",
- "Int Spk", "LOP",
- "Int Spk", "LON",
- "Mic Jack", "MICBIAS",
- "IN1R", "Mic Jack";
- nvidia,i2s-controller = <&tegra_i2s1>;
- nvidia,audio-codec = <&wm8903>;
-
- nvidia,spkr-en-gpios = <&wm8903 2 0>;
- nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
- };
-
- serial@70006000 {
- status = "disable";
- };
-
- serial@70006040 {
- status = "disable";
+ magnetometer@c {
+ compatible = "ak8975";
+ reg = <0xc>;
+ interrupt-parent = <&gpio>;
+ interrupts = <109 0x04>; /* gpio PN5 */
+ };
};
- serial@70006200 {
- status = "disable";
- };
+ emc {
+ emc-table@190000 {
+ reg = <190000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = <190000>;
+ nvidia,emc-registers = <0x0000000c 0x00000026
+ 0x00000009 0x00000003 0x00000004 0x00000004
+ 0x00000002 0x0000000c 0x00000003 0x00000003
+ 0x00000002 0x00000001 0x00000004 0x00000005
+ 0x00000004 0x00000009 0x0000000d 0x0000059f
+ 0x00000000 0x00000003 0x00000003 0x00000003
+ 0x00000003 0x00000001 0x0000000b 0x000000c8
+ 0x00000003 0x00000007 0x00000004 0x0000000f
+ 0x00000002 0x00000000 0x00000000 0x00000002
+ 0x00000000 0x00000000 0x00000083 0xa06204ae
+ 0x007dc010 0x00000000 0x00000000 0x00000000
+ 0x00000000 0x00000000 0x00000000 0x00000000>;
+ };
- serial@70006300 {
- clock-frequency = < 216000000 >;
+ emc-table@380000 {
+ reg = <380000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = <380000>;
+ nvidia,emc-registers = <0x00000017 0x0000004b
+ 0x00000012 0x00000006 0x00000004 0x00000005
+ 0x00000003 0x0000000c 0x00000006 0x00000006
+ 0x00000003 0x00000001 0x00000004 0x00000005
+ 0x00000004 0x00000009 0x0000000d 0x00000b5f
+ 0x00000000 0x00000003 0x00000003 0x00000006
+ 0x00000006 0x00000001 0x00000011 0x000000c8
+ 0x00000003 0x0000000e 0x00000007 0x0000000f
+ 0x00000002 0x00000000 0x00000000 0x00000002
+ 0x00000000 0x00000000 0x00000083 0xe044048b
+ 0x007d8010 0x00000000 0x00000000 0x00000000
+ 0x00000000 0x00000000 0x00000000 0x00000000>;
+ };
};
- serial@70006400 {
- status = "disable";
+ usb@c5000000 {
+ status = "okay";
+ nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */
+ dr_mode = "otg";
};
- sdhci@c8000000 {
- status = "disable";
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
};
- sdhci@c8000200 {
- status = "disable";
+ usb@c5008000 {
+ status = "okay";
};
sdhci@c8000400 {
+ status = "okay";
cd-gpios = <&gpio 69 0>; /* gpio PI5 */
wp-gpios = <&gpio 57 0>; /* gpio PH1 */
power-gpios = <&gpio 70 0>; /* gpio PI6 */
};
sdhci@c8000600 {
+ status = "okay";
support-8bit;
bus-width = <8>;
};
- usb@c5000000 {
- nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */
- dr_mode = "otg";
- };
-
gpio-keys {
compatible = "gpio-keys";
};
};
- emc@7000f400 {
- emc-table@190000 {
- reg = < 190000 >;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = < 190000 >;
- nvidia,emc-registers = < 0x0000000c 0x00000026
- 0x00000009 0x00000003 0x00000004 0x00000004
- 0x00000002 0x0000000c 0x00000003 0x00000003
- 0x00000002 0x00000001 0x00000004 0x00000005
- 0x00000004 0x00000009 0x0000000d 0x0000059f
- 0x00000000 0x00000003 0x00000003 0x00000003
- 0x00000003 0x00000001 0x0000000b 0x000000c8
- 0x00000003 0x00000007 0x00000004 0x0000000f
- 0x00000002 0x00000000 0x00000000 0x00000002
- 0x00000000 0x00000000 0x00000083 0xa06204ae
- 0x007dc010 0x00000000 0x00000000 0x00000000
- 0x00000000 0x00000000 0x00000000 0x00000000 >;
- };
+ sound {
+ compatible = "nvidia,tegra-audio-wm8903-seaboard",
+ "nvidia,tegra-audio-wm8903";
+ nvidia,model = "NVIDIA Tegra Seaboard";
- emc-table@380000 {
- reg = < 380000 >;
- compatible = "nvidia,tegra20-emc-table";
- clock-frequency = < 380000 >;
- nvidia,emc-registers = < 0x00000017 0x0000004b
- 0x00000012 0x00000006 0x00000004 0x00000005
- 0x00000003 0x0000000c 0x00000006 0x00000006
- 0x00000003 0x00000001 0x00000004 0x00000005
- 0x00000004 0x00000009 0x0000000d 0x00000b5f
- 0x00000000 0x00000003 0x00000003 0x00000006
- 0x00000006 0x00000001 0x00000011 0x000000c8
- 0x00000003 0x0000000e 0x00000007 0x0000000f
- 0x00000002 0x00000000 0x00000000 0x00000002
- 0x00000000 0x00000000 0x00000083 0xe044048b
- 0x007d8010 0x00000000 0x00000000 0x00000000
- 0x00000000 0x00000000 0x00000000 0x00000000 >;
- };
- };
+ nvidia,audio-routing =
+ "Headphone Jack", "HPOUTR",
+ "Headphone Jack", "HPOUTL",
+ "Int Spk", "ROP",
+ "Int Spk", "RON",
+ "Int Spk", "LOP",
+ "Int Spk", "LON",
+ "Mic Jack", "MICBIAS",
+ "IN1R", "Mic Jack";
- usb@c5004000 {
- nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&wm8903>;
+
+ nvidia,spkr-en-gpios = <&wm8903 2 0>;
+ nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
};
};
model = "Compulab TrimSlice board";
compatible = "compulab,trimslice", "nvidia,tegra20";
- memory@0 {
- reg = < 0x00000000 0x40000000 >;
+ memory {
+ reg = <0x00000000 0x40000000>;
};
- pinmux@70000000 {
+ pinmux {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
};
};
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006000 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
i2c@7000c000 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000c400 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000c500 {
+ status = "okay";
clock-frequency = <400000>;
- };
-
- i2c@7000d000 {
- status = "disable";
- };
-
- i2s@70002800 {
- status = "disable";
- };
-
- i2s@70002a00 {
- status = "disable";
- };
- das@70000c00 {
- status = "disable";
- };
-
- serial@70006000 {
- clock-frequency = < 216000000 >;
- };
+ codec: codec@1a {
+ compatible = "ti,tlv320aic23";
+ reg = <0x1a>;
+ };
- serial@70006040 {
- status = "disable";
+ rtc@56 {
+ compatible = "emmicro,em3027";
+ reg = <0x56>;
+ };
};
- serial@70006200 {
- status = "disable";
+ usb@c5000000 {
+ status = "okay";
};
- serial@70006300 {
- status = "disable";
+ usb@c5004000 {
+ nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
};
- serial@70006400 {
- status = "disable";
+ usb@c5008000 {
+ status = "okay";
};
sdhci@c8000000 {
- status = "disable";
- };
-
- sdhci@c8000200 {
- status = "disable";
- };
-
- sdhci@c8000400 {
- status = "disable";
+ status = "okay";
+ bus-width = <4>;
};
sdhci@c8000600 {
- cd-gpios = <&gpio 121 0>;
- wp-gpios = <&gpio 122 0>;
+ status = "okay";
+ cd-gpios = <&gpio 121 0>; /* gpio PP1 */
+ wp-gpios = <&gpio 122 0>; /* gpio PP2 */
+ bus-width = <4>;
};
- usb@c5004000 {
- nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
+ sound {
+ compatible = "nvidia,tegra-audio-trimslice";
+ nvidia,i2s-controller = <&tegra_i2s1>;
+ nvidia,audio-codec = <&codec>;
};
};
compatible = "nvidia,ventana", "nvidia,tegra20";
memory {
- reg = < 0x00000000 0x40000000 >;
+ reg = <0x00000000 0x40000000>;
};
- pinmux@70000000 {
+ pinmux {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
};
};
+ i2s@70002800 {
+ status = "okay";
+ };
+
+ serial@70006300 {
+ status = "okay";
+ clock-frequency = <216000000>;
+ };
+
i2c@7000c000 {
+ status = "okay";
clock-frequency = <400000>;
wm8903: wm8903@1a {
compatible = "wlf,wm8903";
reg = <0x1a>;
interrupt-parent = <&gpio>;
- interrupts = < 187 0x04 >;
+ interrupts = <187 0x04>;
gpio-controller;
#gpio-cells = <2>;
micdet-cfg = <0>;
micdet-delay = <100>;
- gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+ gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+ };
+
+ /* ALS and proximity sensor */
+ isl29018@44 {
+ compatible = "isil,isl29018";
+ reg = <0x44>;
+ interrupt-parent = <&gpio>;
+ interrupts = <202 0x04>; /*gpio PZ2 */
};
};
i2c@7000c400 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000c500 {
+ status = "okay";
clock-frequency = <400000>;
};
i2c@7000d000 {
+ status = "okay";
clock-frequency = <400000>;
};
- i2s@70002a00 {
- status = "disable";
+ usb@c5000000 {
+ status = "okay";
+ };
+
+ usb@c5004000 {
+ status = "okay";
+ nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+ };
+
+ usb@c5008000 {
+ status = "okay";
+ };
+
+ sdhci@c8000400 {
+ status = "okay";
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
+ bus-width = <4>;
+ };
+
+ sdhci@c8000600 {
+ status = "okay";
+ support-8bit;
+ bus-width = <8>;
};
sound {
nvidia,spkr-en-gpios = <&wm8903 2 0>;
nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
- nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+ nvidia,int-mic-en-gpios = <&gpio 184 0>; /* gpio PX0 */
nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
};
-
- serial@70006000 {
- status = "disable";
- };
-
- serial@70006040 {
- status = "disable";
- };
-
- serial@70006200 {
- status = "disable";
- };
-
- serial@70006300 {
- clock-frequency = < 216000000 >;
- };
-
- serial@70006400 {
- status = "disable";
- };
-
- sdhci@c8000000 {
- status = "disable";
- };
-
- sdhci@c8000200 {
- status = "disable";
- };
-
- sdhci@c8000400 {
- cd-gpios = <&gpio 69 0>; /* gpio PI5 */
- wp-gpios = <&gpio 57 0>; /* gpio PH1 */
- power-gpios = <&gpio 70 0>; /* gpio PI6 */
- bus-width = <4>;
- };
-
- sdhci@c8000600 {
- support-8bit;
- bus-width = <8>;
- };
-
- usb@c5004000 {
- nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
- };
};
compatible = "nvidia,tegra20";
interrupt-parent = <&intc>;
- pmc@7000f400 {
- compatible = "nvidia,tegra20-pmc";
- reg = <0x7000e400 0x400>;
- };
-
- intc: interrupt-controller@50041000 {
+ intc: interrupt-controller {
compatible = "arm,cortex-a9-gic";
+ reg = <0x50041000 0x1000
+ 0x50040100 0x0100>;
interrupt-controller;
#interrupt-cells = <3>;
- reg = < 0x50041000 0x1000 >,
- < 0x50040100 0x0100 >;
};
- pmu {
- compatible = "arm,cortex-a9-pmu";
- interrupts = <0 56 0x04
- 0 57 0x04>;
- };
-
- apbdma: dma@6000a000 {
+ apbdma: dma {
compatible = "nvidia,tegra20-apbdma";
reg = <0x6000a000 0x1200>;
- interrupts = < 0 104 0x04
- 0 105 0x04
- 0 106 0x04
- 0 107 0x04
- 0 108 0x04
- 0 109 0x04
- 0 110 0x04
- 0 111 0x04
- 0 112 0x04
- 0 113 0x04
- 0 114 0x04
- 0 115 0x04
- 0 116 0x04
- 0 117 0x04
- 0 118 0x04
- 0 119 0x04 >;
- };
-
- i2c@7000c000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra20-i2c";
- reg = <0x7000C000 0x100>;
- interrupts = < 0 38 0x04 >;
- };
-
- i2c@7000c400 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra20-i2c";
- reg = <0x7000C400 0x100>;
- interrupts = < 0 84 0x04 >;
+ interrupts = <0 104 0x04
+ 0 105 0x04
+ 0 106 0x04
+ 0 107 0x04
+ 0 108 0x04
+ 0 109 0x04
+ 0 110 0x04
+ 0 111 0x04
+ 0 112 0x04
+ 0 113 0x04
+ 0 114 0x04
+ 0 115 0x04
+ 0 116 0x04
+ 0 117 0x04
+ 0 118 0x04
+ 0 119 0x04>;
+ };
+
+ ahb {
+ compatible = "nvidia,tegra20-ahb";
+ reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */
+ };
+
+ gpio: gpio {
+ compatible = "nvidia,tegra20-gpio";
+ reg = <0x6000d000 0x1000>;
+ interrupts = <0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
};
- i2c@7000c500 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra20-i2c";
- reg = <0x7000C500 0x100>;
- interrupts = < 0 92 0x04 >;
+ pinmux: pinmux {
+ compatible = "nvidia,tegra20-pinmux";
+ reg = <0x70000014 0x10 /* Tri-state registers */
+ 0x70000080 0x20 /* Mux registers */
+ 0x700000a0 0x14 /* Pull-up/down registers */
+ 0x70000868 0xa8>; /* Pad control registers */
};
- i2c@7000d000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra20-i2c-dvc";
- reg = <0x7000D000 0x200>;
- interrupts = < 0 53 0x04 >;
+ das {
+ compatible = "nvidia,tegra20-das";
+ reg = <0x70000c00 0x80>;
};
tegra_i2s1: i2s@70002800 {
compatible = "nvidia,tegra20-i2s";
reg = <0x70002800 0x200>;
- interrupts = < 0 13 0x04 >;
- nvidia,dma-request-selector = < &apbdma 2 >;
+ interrupts = <0 13 0x04>;
+ nvidia,dma-request-selector = <&apbdma 2>;
+ status = "disable";
};
tegra_i2s2: i2s@70002a00 {
compatible = "nvidia,tegra20-i2s";
reg = <0x70002a00 0x200>;
- interrupts = < 0 3 0x04 >;
- nvidia,dma-request-selector = < &apbdma 1 >;
- };
-
- das@70000c00 {
- compatible = "nvidia,tegra20-das";
- reg = <0x70000c00 0x80>;
- };
-
- gpio: gpio@6000d000 {
- compatible = "nvidia,tegra20-gpio";
- reg = < 0x6000d000 0x1000 >;
- interrupts = < 0 32 0x04
- 0 33 0x04
- 0 34 0x04
- 0 35 0x04
- 0 55 0x04
- 0 87 0x04
- 0 89 0x04 >;
- #gpio-cells = <2>;
- gpio-controller;
- #interrupt-cells = <2>;
- interrupt-controller;
- };
-
- pinmux: pinmux@70000000 {
- compatible = "nvidia,tegra20-pinmux";
- reg = < 0x70000014 0x10 /* Tri-state registers */
- 0x70000080 0x20 /* Mux registers */
- 0x700000a0 0x14 /* Pull-up/down registers */
- 0x70000868 0xa8 >; /* Pad control registers */
+ interrupts = <0 3 0x04>;
+ nvidia,dma-request-selector = <&apbdma 1>;
+ status = "disable";
};
serial@70006000 {
compatible = "nvidia,tegra20-uart";
reg = <0x70006000 0x40>;
reg-shift = <2>;
- interrupts = < 0 36 0x04 >;
+ interrupts = <0 36 0x04>;
+ status = "disable";
};
serial@70006040 {
compatible = "nvidia,tegra20-uart";
reg = <0x70006040 0x40>;
reg-shift = <2>;
- interrupts = < 0 37 0x04 >;
+ interrupts = <0 37 0x04>;
+ status = "disable";
};
serial@70006200 {
compatible = "nvidia,tegra20-uart";
reg = <0x70006200 0x100>;
reg-shift = <2>;
- interrupts = < 0 46 0x04 >;
+ interrupts = <0 46 0x04>;
+ status = "disable";
};
serial@70006300 {
compatible = "nvidia,tegra20-uart";
reg = <0x70006300 0x100>;
reg-shift = <2>;
- interrupts = < 0 90 0x04 >;
+ interrupts = <0 90 0x04>;
+ status = "disable";
};
serial@70006400 {
compatible = "nvidia,tegra20-uart";
reg = <0x70006400 0x100>;
reg-shift = <2>;
- interrupts = < 0 91 0x04 >;
+ interrupts = <0 91 0x04>;
+ status = "disable";
};
- emc@7000f400 {
+ i2c@7000c000 {
+ compatible = "nvidia,tegra20-i2c";
+ reg = <0x7000c000 0x100>;
+ interrupts = <0 38 0x04>;
#address-cells = <1>;
#size-cells = <0>;
- compatible = "nvidia,tegra20-emc";
- reg = <0x7000f400 0x200>;
+ status = "disable";
};
- sdhci@c8000000 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000000 0x200>;
- interrupts = < 0 14 0x04 >;
+ i2c@7000c400 {
+ compatible = "nvidia,tegra20-i2c";
+ reg = <0x7000c400 0x100>;
+ interrupts = <0 84 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- sdhci@c8000200 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000200 0x200>;
- interrupts = < 0 15 0x04 >;
+ i2c@7000c500 {
+ compatible = "nvidia,tegra20-i2c";
+ reg = <0x7000c500 0x100>;
+ interrupts = <0 92 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- sdhci@c8000400 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000400 0x200>;
- interrupts = < 0 19 0x04 >;
+ i2c@7000d000 {
+ compatible = "nvidia,tegra20-i2c-dvc";
+ reg = <0x7000d000 0x200>;
+ interrupts = <0 53 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- sdhci@c8000600 {
- compatible = "nvidia,tegra20-sdhci";
- reg = <0xc8000600 0x200>;
- interrupts = < 0 31 0x04 >;
+ pmc {
+ compatible = "nvidia,tegra20-pmc";
+ reg = <0x7000e400 0x400>;
+ };
+
+ mc {
+ compatible = "nvidia,tegra20-mc";
+ reg = <0x7000f000 0x024
+ 0x7000f03c 0x3c4>;
+ interrupts = <0 77 0x04>;
+ };
+
+ gart {
+ compatible = "nvidia,tegra20-gart";
+ reg = <0x7000f024 0x00000018 /* controller registers */
+ 0x58000000 0x02000000>; /* GART aperture */
+ };
+
+ emc {
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f400 0x200>;
+ #address-cells = <1>;
+ #size-cells = <0>;
};
usb@c5000000 {
compatible = "nvidia,tegra20-ehci", "usb-ehci";
reg = <0xc5000000 0x4000>;
- interrupts = < 0 20 0x04 >;
+ interrupts = <0 20 0x04>;
phy_type = "utmi";
nvidia,has-legacy-mode;
+ status = "disable";
};
usb@c5004000 {
compatible = "nvidia,tegra20-ehci", "usb-ehci";
reg = <0xc5004000 0x4000>;
- interrupts = < 0 21 0x04 >;
+ interrupts = <0 21 0x04>;
phy_type = "ulpi";
+ status = "disable";
};
usb@c5008000 {
compatible = "nvidia,tegra20-ehci", "usb-ehci";
reg = <0xc5008000 0x4000>;
- interrupts = < 0 97 0x04 >;
+ interrupts = <0 97 0x04>;
phy_type = "utmi";
+ status = "disable";
+ };
+
+ sdhci@c8000000 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000000 0x200>;
+ interrupts = <0 14 0x04>;
+ status = "disable";
};
-};
+ sdhci@c8000200 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000200 0x200>;
+ interrupts = <0 15 0x04>;
+ status = "disable";
+ };
+
+ sdhci@c8000400 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000400 0x200>;
+ interrupts = <0 19 0x04>;
+ status = "disable";
+ };
+
+ sdhci@c8000600 {
+ compatible = "nvidia,tegra20-sdhci";
+ reg = <0xc8000600 0x200>;
+ interrupts = <0 31 0x04>;
+ status = "disable";
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 56 0x04
+ 0 57 0x04>;
+ };
+};
compatible = "nvidia,tegra30";
interrupt-parent = <&intc>;
- pmc@7000f400 {
- compatible = "nvidia,tegra20-pmc", "nvidia,tegra30-pmc";
- reg = <0x7000e400 0x400>;
- };
-
- intc: interrupt-controller@50041000 {
+ intc: interrupt-controller {
compatible = "arm,cortex-a9-gic";
+ reg = <0x50041000 0x1000
+ 0x50040100 0x0100>;
interrupt-controller;
#interrupt-cells = <3>;
- reg = < 0x50041000 0x1000 >,
- < 0x50040100 0x0100 >;
};
- pmu {
- compatible = "arm,cortex-a9-pmu";
- interrupts = <0 144 0x04
- 0 145 0x04
- 0 146 0x04
- 0 147 0x04>;
- };
-
- apbdma: dma@6000a000 {
+ apbdma: dma {
compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
reg = <0x6000a000 0x1400>;
- interrupts = < 0 104 0x04
- 0 105 0x04
- 0 106 0x04
- 0 107 0x04
- 0 108 0x04
- 0 109 0x04
- 0 110 0x04
- 0 111 0x04
- 0 112 0x04
- 0 113 0x04
- 0 114 0x04
- 0 115 0x04
- 0 116 0x04
- 0 117 0x04
- 0 118 0x04
- 0 119 0x04
- 0 128 0x04
- 0 129 0x04
- 0 130 0x04
- 0 131 0x04
- 0 132 0x04
- 0 133 0x04
- 0 134 0x04
- 0 135 0x04
- 0 136 0x04
- 0 137 0x04
- 0 138 0x04
- 0 139 0x04
- 0 140 0x04
- 0 141 0x04
- 0 142 0x04
- 0 143 0x04 >;
+ interrupts = <0 104 0x04
+ 0 105 0x04
+ 0 106 0x04
+ 0 107 0x04
+ 0 108 0x04
+ 0 109 0x04
+ 0 110 0x04
+ 0 111 0x04
+ 0 112 0x04
+ 0 113 0x04
+ 0 114 0x04
+ 0 115 0x04
+ 0 116 0x04
+ 0 117 0x04
+ 0 118 0x04
+ 0 119 0x04
+ 0 128 0x04
+ 0 129 0x04
+ 0 130 0x04
+ 0 131 0x04
+ 0 132 0x04
+ 0 133 0x04
+ 0 134 0x04
+ 0 135 0x04
+ 0 136 0x04
+ 0 137 0x04
+ 0 138 0x04
+ 0 139 0x04
+ 0 140 0x04
+ 0 141 0x04
+ 0 142 0x04
+ 0 143 0x04>;
};
- i2c@7000c000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
- reg = <0x7000C000 0x100>;
- interrupts = < 0 38 0x04 >;
- };
-
- i2c@7000c400 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
- reg = <0x7000C400 0x100>;
- interrupts = < 0 84 0x04 >;
+ ahb: ahb {
+ compatible = "nvidia,tegra30-ahb";
+ reg = <0x6000c004 0x14c>; /* AHB Arbitration + Gizmo Controller */
};
- i2c@7000c500 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
- reg = <0x7000C500 0x100>;
- interrupts = < 0 92 0x04 >;
- };
-
- i2c@7000c700 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
- reg = <0x7000c700 0x100>;
- interrupts = < 0 120 0x04 >;
- };
-
- i2c@7000d000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
- reg = <0x7000D000 0x100>;
- interrupts = < 0 53 0x04 >;
- };
-
- gpio: gpio@6000d000 {
+ gpio: gpio {
compatible = "nvidia,tegra30-gpio", "nvidia,tegra20-gpio";
- reg = < 0x6000d000 0x1000 >;
- interrupts = < 0 32 0x04
- 0 33 0x04
- 0 34 0x04
- 0 35 0x04
- 0 55 0x04
- 0 87 0x04
- 0 89 0x04
- 0 125 0x04 >;
+ reg = <0x6000d000 0x1000>;
+ interrupts = <0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04
+ 0 125 0x04>;
#gpio-cells = <2>;
gpio-controller;
#interrupt-cells = <2>;
interrupt-controller;
};
+ pinmux: pinmux {
+ compatible = "nvidia,tegra30-pinmux";
+ reg = <0x70000868 0xd0 /* Pad control registers */
+ 0x70003000 0x3e0>; /* Mux registers */
+ };
+
serial@70006000 {
compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
reg = <0x70006000 0x40>;
reg-shift = <2>;
- interrupts = < 0 36 0x04 >;
+ interrupts = <0 36 0x04>;
+ status = "disable";
};
serial@70006040 {
compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
reg = <0x70006040 0x40>;
reg-shift = <2>;
- interrupts = < 0 37 0x04 >;
+ interrupts = <0 37 0x04>;
+ status = "disable";
};
serial@70006200 {
compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
reg = <0x70006200 0x100>;
reg-shift = <2>;
- interrupts = < 0 46 0x04 >;
+ interrupts = <0 46 0x04>;
+ status = "disable";
};
serial@70006300 {
compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
reg = <0x70006300 0x100>;
reg-shift = <2>;
- interrupts = < 0 90 0x04 >;
+ interrupts = <0 90 0x04>;
+ status = "disable";
};
serial@70006400 {
compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
reg = <0x70006400 0x100>;
reg-shift = <2>;
- interrupts = < 0 91 0x04 >;
+ interrupts = <0 91 0x04>;
+ status = "disable";
};
- sdhci@78000000 {
- compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
- reg = <0x78000000 0x200>;
- interrupts = < 0 14 0x04 >;
+ i2c@7000c000 {
+ compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+ reg = <0x7000c000 0x100>;
+ interrupts = <0 38 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- sdhci@78000200 {
- compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
- reg = <0x78000200 0x200>;
- interrupts = < 0 15 0x04 >;
+ i2c@7000c400 {
+ compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+ reg = <0x7000c400 0x100>;
+ interrupts = <0 84 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- sdhci@78000400 {
- compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
- reg = <0x78000400 0x200>;
- interrupts = < 0 19 0x04 >;
+ i2c@7000c500 {
+ compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+ reg = <0x7000c500 0x100>;
+ interrupts = <0 92 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- sdhci@78000600 {
- compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
- reg = <0x78000600 0x200>;
- interrupts = < 0 31 0x04 >;
+ i2c@7000c700 {
+ compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+ reg = <0x7000c700 0x100>;
+ interrupts = <0 120 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
};
- pinmux: pinmux@70000000 {
- compatible = "nvidia,tegra30-pinmux";
- reg = < 0x70000868 0xd0 /* Pad control registers */
- 0x70003000 0x3e0 >; /* Mux registers */
+ i2c@7000d000 {
+ compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+ reg = <0x7000d000 0x100>;
+ interrupts = <0 53 0x04>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disable";
+ };
+
+ pmc {
+ compatible = "nvidia,tegra20-pmc", "nvidia,tegra30-pmc";
+ reg = <0x7000e400 0x400>;
+ };
+
+ mc {
+ compatible = "nvidia,tegra30-mc";
+ reg = <0x7000f000 0x010
+ 0x7000f03c 0x1b4
+ 0x7000f200 0x028
+ 0x7000f284 0x17c>;
+ interrupts = <0 77 0x04>;
+ };
+
+ smmu {
+ compatible = "nvidia,tegra30-smmu";
+ reg = <0x7000f010 0x02c
+ 0x7000f1f0 0x010
+ 0x7000f228 0x05c>;
+ nvidia,#asids = <4>; /* # of ASIDs */
+ dma-window = <0 0x40000000>; /* IOVA start & length */
+ nvidia,ahb = <&ahb>;
};
ahub {
compatible = "nvidia,tegra30-ahub";
- reg = <0x70080000 0x200 0x70080200 0x100>;
- interrupts = < 0 103 0x04 >;
+ reg = <0x70080000 0x200
+ 0x70080200 0x100>;
+ interrupts = <0 103 0x04>;
nvidia,dma-request-selector = <&apbdma 1>;
ranges;
compatible = "nvidia,tegra30-i2s";
reg = <0x70080300 0x100>;
nvidia,ahub-cif-ids = <4 4>;
+ status = "disable";
};
tegra_i2s1: i2s@70080400 {
compatible = "nvidia,tegra30-i2s";
reg = <0x70080400 0x100>;
nvidia,ahub-cif-ids = <5 5>;
+ status = "disable";
};
tegra_i2s2: i2s@70080500 {
compatible = "nvidia,tegra30-i2s";
reg = <0x70080500 0x100>;
nvidia,ahub-cif-ids = <6 6>;
+ status = "disable";
};
tegra_i2s3: i2s@70080600 {
compatible = "nvidia,tegra30-i2s";
reg = <0x70080600 0x100>;
nvidia,ahub-cif-ids = <7 7>;
+ status = "disable";
};
tegra_i2s4: i2s@70080700 {
compatible = "nvidia,tegra30-i2s";
reg = <0x70080700 0x100>;
nvidia,ahub-cif-ids = <8 8>;
+ status = "disable";
};
};
+
+ sdhci@78000000 {
+ compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+ reg = <0x78000000 0x200>;
+ interrupts = <0 14 0x04>;
+ status = "disable";
+ };
+
+ sdhci@78000200 {
+ compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+ reg = <0x78000200 0x200>;
+ interrupts = <0 15 0x04>;
+ status = "disable";
+ };
+
+ sdhci@78000400 {
+ compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+ reg = <0x78000400 0x200>;
+ interrupts = <0 19 0x04>;
+ status = "disable";
+ };
+
+ sdhci@78000600 {
+ compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+ reg = <0x78000600 0x200>;
+ interrupts = <0 31 0x04>;
+ status = "disable";
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 144 0x04
+ 0 145 0x04
+ 0 146 0x04
+ 0 147 0x04>;
+ };
};
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_MXS=y
+CONFIG_MACH_MXS_DT=y
CONFIG_MACH_MX23EVK=y
CONFIG_MACH_MX28EVK=y
CONFIG_MACH_STMP378X_DEVB=y
dtb-$(CONFIG_MACH_IMX53_DT) += imx53-ard.dtb imx53-evk.dtb \
imx53-qsb.dtb imx53-smd.dtb
dtb-$(CONFIG_SOC_IMX6Q) += imx6q-arm2.dtb \
- imx6q-sabrelite.dtb
+ imx6q-sabrelite.dtb \
+ imx6q-sabresd.dtb \
static const char *per_root_sel[] = { "per_podf", "ipg", };
static const char *esdhc_c_sel[] = { "esdhc_a_podf", "esdhc_b_podf", };
static const char *esdhc_d_sel[] = { "esdhc_a_podf", "esdhc_b_podf", };
+static const char *ssi_apm_sels[] = { "ckih1", "lp_amp", "ckih2", };
+static const char *ssi_clk_sels[] = { "pll1_sw", "pll2_sw", "pll3_sw", "ssi_apm", };
+static const char *ssi3_clk_sels[] = { "ssi1_root_gate", "ssi2_root_gate", };
+static const char *ssi_ext1_com_sels[] = { "ssi_ext1_podf", "ssi1_root_gate", };
+static const char *ssi_ext2_com_sels[] = { "ssi_ext2_podf", "ssi2_root_gate", };
static const char *emi_slow_sel[] = { "main_bus", "ahb", };
static const char *usb_phy_sel_str[] = { "osc", "usb_phy_podf", };
static const char *mx51_ipu_di0_sel[] = { "di_pred", "osc", "ckih1", "tve_di", };
pll3_sw, ipu_di0_sel, ipu_di1_sel, tve_ext_sel, mx51_mipi, pll4_sw,
ldb_di1_sel, di_pll4_podf, ldb_di0_sel, ldb_di0_gate, usb_phy1_gate,
usb_phy2_gate, per_lp_apm, per_pred1, per_pred2, per_podf, per_root,
+ ssi_apm, ssi1_root_sel, ssi2_root_sel, ssi3_root_sel, ssi_ext1_sel,
+ ssi_ext2_sel, ssi_ext1_com_sel, ssi_ext2_com_sel, ssi1_root_pred,
+ ssi1_root_podf, ssi2_root_pred, ssi2_root_podf, ssi_ext1_pred,
+ ssi_ext1_podf, ssi_ext2_pred, ssi_ext2_podf, ssi1_root_gate,
+ ssi2_root_gate, ssi3_root_gate, ssi_ext1_gate, ssi_ext2_gate,
clk_max
};
clk[uart5_per_gate] = imx_clk_gate2("uart5_per_gate", "uart_root", MXC_CCM_CCGR7, 14);
clk[gpc_dvfs] = imx_clk_gate2("gpc_dvfs", "dummy", MXC_CCM_CCGR5, 24);
+ clk[ssi_apm] = imx_clk_mux("ssi_apm", MXC_CCM_CSCMR1, 8, 2, ssi_apm_sels, ARRAY_SIZE(ssi_apm_sels));
+ clk[ssi1_root_sel] = imx_clk_mux("ssi1_root_sel", MXC_CCM_CSCMR1, 14, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+ clk[ssi2_root_sel] = imx_clk_mux("ssi2_root_sel", MXC_CCM_CSCMR1, 12, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+ clk[ssi3_root_sel] = imx_clk_mux("ssi3_root_sel", MXC_CCM_CSCMR1, 11, 1, ssi3_clk_sels, ARRAY_SIZE(ssi3_clk_sels));
+ clk[ssi_ext1_sel] = imx_clk_mux("ssi_ext1_sel", MXC_CCM_CSCMR1, 28, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+ clk[ssi_ext2_sel] = imx_clk_mux("ssi_ext2_sel", MXC_CCM_CSCMR1, 30, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+ clk[ssi_ext1_com_sel] = imx_clk_mux("ssi_ext1_com_sel", MXC_CCM_CSCMR1, 0, 1, ssi_ext1_com_sels, ARRAY_SIZE(ssi_ext1_com_sels));
+ clk[ssi_ext2_com_sel] = imx_clk_mux("ssi_ext2_com_sel", MXC_CCM_CSCMR1, 1, 1, ssi_ext2_com_sels, ARRAY_SIZE(ssi_ext2_com_sels));
+ clk[ssi1_root_pred] = imx_clk_divider("ssi1_root_pred", "ssi1_root_sel", MXC_CCM_CS1CDR, 6, 3);
+ clk[ssi1_root_podf] = imx_clk_divider("ssi1_root_podf", "ssi1_root_pred", MXC_CCM_CS1CDR, 0, 6);
+ clk[ssi2_root_pred] = imx_clk_divider("ssi2_root_pred", "ssi2_root_sel", MXC_CCM_CS2CDR, 6, 3);
+ clk[ssi2_root_podf] = imx_clk_divider("ssi2_root_podf", "ssi2_root_pred", MXC_CCM_CS2CDR, 0, 6);
+ clk[ssi_ext1_pred] = imx_clk_divider("ssi_ext1_pred", "ssi_ext1_sel", MXC_CCM_CS1CDR, 22, 3);
+ clk[ssi_ext1_podf] = imx_clk_divider("ssi_ext1_podf", "ssi_ext1_pred", MXC_CCM_CS1CDR, 16, 6);
+ clk[ssi_ext2_pred] = imx_clk_divider("ssi_ext2_pred", "ssi_ext2_sel", MXC_CCM_CS2CDR, 22, 3);
+ clk[ssi_ext2_podf] = imx_clk_divider("ssi_ext2_podf", "ssi_ext2_pred", MXC_CCM_CS2CDR, 16, 6);
+ clk[ssi1_root_gate] = imx_clk_gate2("ssi1_root_gate", "ssi1_root_podf", MXC_CCM_CCGR3, 18);
+ clk[ssi2_root_gate] = imx_clk_gate2("ssi2_root_gate", "ssi2_root_podf", MXC_CCM_CCGR3, 22);
+ clk[ssi3_root_gate] = imx_clk_gate2("ssi3_root_gate", "ssi3_root_sel", MXC_CCM_CCGR3, 26);
+ clk[ssi_ext1_gate] = imx_clk_gate2("ssi_ext1_gate", "ssi_ext1_com_sel", MXC_CCM_CCGR3, 28);
+ clk[ssi_ext2_gate] = imx_clk_gate2("ssi_ext2_gate", "ssi_ext2_com_sel", MXC_CCM_CCGR3, 30);
+
for (i = 0; i < ARRAY_SIZE(clk); i++)
if (IS_ERR(clk[i]))
pr_err("i.MX5 clk %d: register failed with %ld\n",
clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "imx-ssi.0");
clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "imx-ssi.1");
clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "imx-ssi.2");
+ clk_register_clkdev(clk[ssi_ext1_gate], "ssi_ext1", NULL);
+ clk_register_clkdev(clk[ssi_ext2_gate], "ssi_ext2", NULL);
clk_register_clkdev(clk[sdma_gate], NULL, "imx35-sdma");
clk_register_clkdev(clk[cpu_podf], "cpu", NULL);
clk_register_clkdev(clk[iim_gate], "iim", NULL);
clk_register_clkdev(clk[esdhc4_ipg_gate], "ipg", "sdhci-esdhc-imx51.3");
clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx51.3");
clk_register_clkdev(clk[esdhc4_per_gate], "per", "sdhci-esdhc-imx51.3");
+ clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "83fcc000.ssi");
+ clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "70014000.ssi");
+ clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "83fe8000.ssi");
/* set the usboh3 parent to pll2_sw */
clk_set_parent(clk[usboh3_sel], clk[pll2_sw]);
clk_register_clkdev(clk[esdhc4_ipg_gate], "ipg", "sdhci-esdhc-imx53.3");
clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx53.3");
clk_register_clkdev(clk[esdhc4_per_gate], "per", "sdhci-esdhc-imx53.3");
+ clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "63fcc000.ssi");
+ clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "50014000.ssi");
+ clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "63fd0000.ssi");
/* set SDHC root clock to 200MHZ*/
clk_set_rate(clk[esdhc_a_podf], 200000000);
gpmi_bch_apb, gpmi_bch, gpmi_io, gpmi_apb, sata, sdma, spba, ssi1,
ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
- pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, clk_max
+ pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg,
+ ssi2_ipg, ssi3_ipg, clk_max
};
static struct clk *clk[clk_max];
clk[sata] = imx_clk_gate2("sata", "ipg", base + 0x7c, 4);
clk[sdma] = imx_clk_gate2("sdma", "ahb", base + 0x7c, 6);
clk[spba] = imx_clk_gate2("spba", "ipg", base + 0x7c, 12);
- clk[ssi1] = imx_clk_gate2("ssi1", "ssi1_podf", base + 0x7c, 18);
- clk[ssi2] = imx_clk_gate2("ssi2", "ssi2_podf", base + 0x7c, 20);
- clk[ssi3] = imx_clk_gate2("ssi3", "ssi3_podf", base + 0x7c, 22);
+ clk[ssi1_ipg] = imx_clk_gate2("ssi1_ipg", "ipg", base + 0x7c, 18);
+ clk[ssi2_ipg] = imx_clk_gate2("ssi2_ipg", "ipg", base + 0x7c, 20);
+ clk[ssi3_ipg] = imx_clk_gate2("ssi3_ipg", "ipg", base + 0x7c, 22);
clk[uart_ipg] = imx_clk_gate2("uart_ipg", "ipg", base + 0x7c, 24);
clk[uart_serial] = imx_clk_gate2("uart_serial", "uart_serial_podf", base + 0x7c, 26);
clk[usboh3] = imx_clk_gate2("usboh3", "ipg", base + 0x80, 0);
clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0");
clk_register_clkdev(clk[twd], NULL, "smp_twd");
clk_register_clkdev(clk[usboh3], NULL, "usboh3");
- clk_register_clkdev(clk[uart_serial], "per", "2020000.uart");
- clk_register_clkdev(clk[uart_ipg], "ipg", "2020000.uart");
- clk_register_clkdev(clk[uart_serial], "per", "21e8000.uart");
- clk_register_clkdev(clk[uart_ipg], "ipg", "21e8000.uart");
- clk_register_clkdev(clk[uart_serial], "per", "21ec000.uart");
- clk_register_clkdev(clk[uart_ipg], "ipg", "21ec000.uart");
- clk_register_clkdev(clk[uart_serial], "per", "21f0000.uart");
- clk_register_clkdev(clk[uart_ipg], "ipg", "21f0000.uart");
- clk_register_clkdev(clk[uart_serial], "per", "21f4000.uart");
- clk_register_clkdev(clk[uart_ipg], "ipg", "21f4000.uart");
- clk_register_clkdev(clk[enet], NULL, "2188000.enet");
+ clk_register_clkdev(clk[uart_serial], "per", "2020000.serial");
+ clk_register_clkdev(clk[uart_ipg], "ipg", "2020000.serial");
+ clk_register_clkdev(clk[uart_serial], "per", "21e8000.serial");
+ clk_register_clkdev(clk[uart_ipg], "ipg", "21e8000.serial");
+ clk_register_clkdev(clk[uart_serial], "per", "21ec000.serial");
+ clk_register_clkdev(clk[uart_ipg], "ipg", "21ec000.serial");
+ clk_register_clkdev(clk[uart_serial], "per", "21f0000.serial");
+ clk_register_clkdev(clk[uart_ipg], "ipg", "21f0000.serial");
+ clk_register_clkdev(clk[uart_serial], "per", "21f4000.serial");
+ clk_register_clkdev(clk[uart_ipg], "ipg", "21f4000.serial");
+ clk_register_clkdev(clk[enet], NULL, "2188000.ethernet");
clk_register_clkdev(clk[usdhc1], NULL, "2190000.usdhc");
clk_register_clkdev(clk[usdhc2], NULL, "2194000.usdhc");
clk_register_clkdev(clk[usdhc3], NULL, "2198000.usdhc");
clk_register_clkdev(clk[sdma], NULL, "20ec000.sdma");
clk_register_clkdev(clk[dummy], NULL, "20bc000.wdog");
clk_register_clkdev(clk[dummy], NULL, "20c0000.wdog");
+ clk_register_clkdev(clk[ssi1_ipg], NULL, "2028000.ssi");
+ clk_register_clkdev(clk[cko1_sel], "cko1_sel", NULL);
+ clk_register_clkdev(clk[ahb], "ahb", NULL);
+ clk_register_clkdev(clk[cko1], "cko1", NULL);
for (i = 0; i < ARRAY_SIZE(clks_init_on); i++) {
c = clk_get_sys(clks_init_on[i], NULL);
* http://www.gnu.org/copyleft/gpl.html
*/
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
{ /* sentinel */ }
};
+static void __init imx53_qsb_init(void)
+{
+ struct clk *clk;
+
+ clk = clk_get_sys(NULL, "ssi_ext1");
+ if (IS_ERR(clk)) {
+ pr_err("failed to get clk ssi_ext1\n");
+ return;
+ }
+
+ clk_register_clkdev(clk, NULL, "0-000a");
+}
+
static void __init imx53_dt_init(void)
{
struct device_node *node;
of_node_put(node);
}
+ if (of_machine_is_compatible("fsl,imx53-qsb"))
+ imx53_qsb_init();
+
of_platform_populate(NULL, of_default_bus_match_table,
imx53_auxdata_lookup, NULL);
}
#include <mach/hardware.h>
static struct map_desc imx_lluart_desc = {
+#ifdef CONFIG_DEBUG_IMX6Q_UART2
+ .virtual = MX6Q_IO_P2V(MX6Q_UART2_BASE_ADDR),
+ .pfn = __phys_to_pfn(MX6Q_UART2_BASE_ADDR),
+ .length = MX6Q_UART2_SIZE,
+ .type = MT_DEVICE,
+#endif
#ifdef CONFIG_DEBUG_IMX6Q_UART4
.virtual = MX6Q_IO_P2V(MX6Q_UART4_BASE_ADDR),
.pfn = __phys_to_pfn(MX6Q_UART4_BASE_ADDR),
* http://www.gnu.org/copyleft/gpl.html
*/
+#include <linux/clk.h>
+#include <linux/clkdev.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
/* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
static int ksz9021rn_phy_fixup(struct phy_device *phydev)
{
- /* min rx data delay */
- phy_write(phydev, 0x0b, 0x8105);
- phy_write(phydev, 0x0c, 0x0000);
+ if (IS_ENABLED(CONFIG_PHYLIB)) {
+ /* min rx data delay */
+ phy_write(phydev, 0x0b, 0x8105);
+ phy_write(phydev, 0x0c, 0x0000);
- /* max rx/tx clock delay, min rx/tx control delay */
- phy_write(phydev, 0x0b, 0x8104);
- phy_write(phydev, 0x0c, 0xf0f0);
- phy_write(phydev, 0x0b, 0x104);
+ /* max rx/tx clock delay, min rx/tx control delay */
+ phy_write(phydev, 0x0b, 0x8104);
+ phy_write(phydev, 0x0c, 0xf0f0);
+ phy_write(phydev, 0x0b, 0x104);
+ }
return 0;
}
+static void __init imx6q_sabrelite_cko1_setup(void)
+{
+ struct clk *cko1_sel, *ahb, *cko1;
+ unsigned long rate;
+
+ cko1_sel = clk_get_sys(NULL, "cko1_sel");
+ ahb = clk_get_sys(NULL, "ahb");
+ cko1 = clk_get_sys(NULL, "cko1");
+ if (IS_ERR(cko1_sel) || IS_ERR(ahb) || IS_ERR(cko1)) {
+ pr_err("cko1 setup failed!\n");
+ goto put_clk;
+ }
+ clk_set_parent(cko1_sel, ahb);
+ rate = clk_round_rate(cko1, 16000000);
+ clk_set_rate(cko1, rate);
+ clk_register_clkdev(cko1, NULL, "0-000a");
+put_clk:
+ if (!IS_ERR(cko1_sel))
+ clk_put(cko1_sel);
+ if (!IS_ERR(ahb))
+ clk_put(ahb);
+ if (!IS_ERR(cko1))
+ clk_put(cko1);
+}
+
+static void __init imx6q_sabrelite_init(void)
+{
+ if (IS_ENABLED(CONFIG_PHYLIB))
+ phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
+ ksz9021rn_phy_fixup);
+ imx6q_sabrelite_cko1_setup();
+}
+
static void __init imx6q_init_machine(void)
{
/*
pinctrl_provide_dummies();
if (of_machine_is_compatible("fsl,imx6q-sabrelite"))
- phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
- ksz9021rn_phy_fixup);
+ imx6q_sabrelite_init();
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
static const char *imx6q_dt_compat[] __initdata = {
"fsl,imx6q-arm2",
"fsl,imx6q-sabrelite",
+ "fsl,imx6q-sabresd",
"fsl,imx6q",
NULL,
};
MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
MX51_PAD_CSPI1_SS0__GPIO4_24,
MX51_PAD_CSPI1_SS1__GPIO4_25,
+
+ /* Audio */
+ MX51_PAD_AUD3_BB_TXD__AUD3_TXD,
+ MX51_PAD_AUD3_BB_RXD__AUD3_RXD,
+ MX51_PAD_AUD3_BB_CK__AUD3_TXC,
+ MX51_PAD_AUD3_BB_FS__AUD3_TXFS,
};
/* Serial ports */
config SOC_IMX23
bool
+ select ARM_AMBA
select CPU_ARM926T
select HAVE_PWM
select PINCTRL_IMX23
config SOC_IMX28
bool
+ select ARM_AMBA
select CPU_ARM926T
select HAVE_PWM
select PINCTRL_IMX28
comment "MXS platforms:"
+config MACH_MXS_DT
+ bool "Support MXS platforms from device tree"
+ select SOC_IMX23
+ select SOC_IMX28
+ help
+ Include support for Freescale MXS platforms(i.MX23 and i.MX28)
+ using the device tree for discovery
+
config MACH_STMP378X_DEVB
bool "Support STMP378x_devb Platform"
select SOC_IMX23
obj-$(CONFIG_MXS_OCOTP) += ocotp.o
obj-$(CONFIG_PM) += pm.o
+obj-$(CONFIG_MACH_MXS_DT) += mach-mxs.o
obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
config MXS_HAVE_AMBA_DUART
bool
- select ARM_AMBA
config MXS_HAVE_PLATFORM_AUART
bool
#include <mach/mx28.h>
#include <mach/devices-common.h>
-static struct platform_device *__init mxs_add_dma(const char *devid,
+struct platform_device *__init mxs_add_dma(const char *devid,
resource_size_t base)
{
struct resource res[] = {
res, ARRAY_SIZE(res), NULL, 0,
DMA_BIT_MASK(32));
}
-
-static int __init mxs_add_mxs_dma(void)
-{
- char *apbh = "mxs-dma-apbh";
- char *apbx = "mxs-dma-apbx";
-
- if (cpu_is_mx23()) {
- mxs_add_dma(apbh, MX23_APBH_DMA_BASE_ADDR);
- mxs_add_dma(apbx, MX23_APBX_DMA_BASE_ADDR);
- }
-
- if (cpu_is_mx28()) {
- mxs_add_dma(apbh, MX28_APBH_DMA_BASE_ADDR);
- mxs_add_dma(apbx, MX28_APBX_DMA_BASE_ADDR);
- }
-
- return 0;
-}
-arch_initcall(mxs_add_mxs_dma);
#include <mach/devices-common.h>
struct platform_device *__init mxs_add_gpio(
- int id, resource_size_t iobase, int irq)
+ char *name, int id, resource_size_t iobase, int irq)
{
struct resource res[] = {
{
};
return platform_device_register_resndata(&mxs_apbh_bus,
- "gpio-mxs", id, res, ARRAY_SIZE(res), NULL, 0);
+ name, id, res, ARRAY_SIZE(res), NULL, 0);
}
-
-static int __init mxs_add_mxs_gpio(void)
-{
- if (cpu_is_mx23()) {
- mxs_add_gpio(0, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO0);
- mxs_add_gpio(1, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO1);
- mxs_add_gpio(2, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO2);
- }
-
- if (cpu_is_mx28()) {
- mxs_add_gpio(0, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO0);
- mxs_add_gpio(1, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO1);
- mxs_add_gpio(2, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO2);
- mxs_add_gpio(3, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO3);
- mxs_add_gpio(4, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO4);
- }
-
- return 0;
-}
-postcore_initcall(mxs_add_mxs_gpio);
#include <mach/mx28.h>
#include <mach/devices-common.h>
-#define mxs_mxs_mmc_data_entry_single(soc, _id, hwid) \
+#define mxs_mxs_mmc_data_entry_single(soc, _devid, _id, hwid) \
{ \
+ .devid = _devid, \
.id = _id, \
.iobase = soc ## _SSP ## hwid ## _BASE_ADDR, \
.dma = soc ## _DMA_SSP ## hwid, \
.irq_dma = soc ## _INT_SSP ## hwid ## _DMA, \
}
-#define mxs_mxs_mmc_data_entry(soc, _id, hwid) \
- [_id] = mxs_mxs_mmc_data_entry_single(soc, _id, hwid)
+#define mxs_mxs_mmc_data_entry(soc, _devid, _id, hwid) \
+ [_id] = mxs_mxs_mmc_data_entry_single(soc, _devid, _id, hwid)
#ifdef CONFIG_SOC_IMX23
const struct mxs_mxs_mmc_data mx23_mxs_mmc_data[] __initconst = {
- mxs_mxs_mmc_data_entry(MX23, 0, 1),
- mxs_mxs_mmc_data_entry(MX23, 1, 2),
+ mxs_mxs_mmc_data_entry(MX23, "imx23-mmc", 0, 1),
+ mxs_mxs_mmc_data_entry(MX23, "imx23-mmc", 1, 2),
};
#endif
#ifdef CONFIG_SOC_IMX28
const struct mxs_mxs_mmc_data mx28_mxs_mmc_data[] __initconst = {
- mxs_mxs_mmc_data_entry(MX28, 0, 0),
- mxs_mxs_mmc_data_entry(MX28, 1, 1),
- mxs_mxs_mmc_data_entry(MX28, 2, 2),
- mxs_mxs_mmc_data_entry(MX28, 3, 3),
+ mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 0, 0),
+ mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 1, 1),
+ mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 2, 2),
+ mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 3, 3),
};
#endif
},
};
- return mxs_add_platform_device("mxs-mmc", data->id,
+ return mxs_add_platform_device(data->devid, data->id,
res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
}
extern int mxs_saif_clkmux_select(unsigned int clkmux);
extern void mx23_soc_init(void);
-extern int mx23_register_gpios(void);
extern int mx23_clocks_init(void);
extern void mx23_map_io(void);
extern void mx23_init_irq(void);
extern void mx28_soc_init(void);
-extern int mx28_register_gpios(void);
extern int mx28_clocks_init(void);
extern void mx28_map_io(void);
extern void mx28_init_irq(void);
extern void icoll_init_irq(void);
+extern struct platform_device *mxs_add_dma(const char *devid,
+ resource_size_t base);
+extern struct platform_device *mxs_add_gpio(char *name, int id,
+ resource_size_t iobase, int irq);
+
#endif /* __MACH_MXS_COMMON_H__ */
const struct mxs_mxs_i2c_data *data);
/* mmc */
-#include <mach/mmc.h>
+#include <linux/mmc/mxs-mmc.h>
struct mxs_mxs_mmc_data {
+ const char *devid;
int id;
resource_size_t iobase;
resource_size_t dma;
+++ /dev/null
-/*
- * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __MACH_MXS_MMC_H__
-#define __MACH_MXS_MMC_H__
-
-struct mxs_mmc_platform_data {
- int wp_gpio; /* write protect pin */
- unsigned int flags;
-#define SLOTF_4_BIT_CAPABLE (1 << 0)
-#define SLOTF_8_BIT_CAPABLE (1 << 1)
-};
-#endif /* __MACH_MXS_MMC_H__ */
--- /dev/null
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2012 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/init.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <mach/common.h>
+
+static int __init mxs_icoll_add_irq_domain(struct device_node *np,
+ struct device_node *interrupt_parent)
+{
+ irq_domain_add_legacy(np, 128, 0, 0, &irq_domain_simple_ops, NULL);
+
+ return 0;
+}
+
+static int __init mxs_gpio_add_irq_domain(struct device_node *np,
+ struct device_node *interrupt_parent)
+{
+ static int gpio_irq_base = MXS_GPIO_IRQ_START;
+
+ irq_domain_add_legacy(np, 32, gpio_irq_base, 0, &irq_domain_simple_ops, NULL);
+ gpio_irq_base += 32;
+
+ return 0;
+}
+
+static const struct of_device_id mxs_irq_match[] __initconst = {
+ { .compatible = "fsl,mxs-icoll", .data = mxs_icoll_add_irq_domain, },
+ { .compatible = "fsl,mxs-gpio", .data = mxs_gpio_add_irq_domain, },
+ { /* sentinel */ }
+};
+
+static void __init mxs_dt_init_irq(void)
+{
+ icoll_init_irq();
+ of_irq_init(mxs_irq_match);
+}
+
+static void __init imx23_timer_init(void)
+{
+ mx23_clocks_init();
+}
+
+static struct sys_timer imx23_timer = {
+ .init = imx23_timer_init,
+};
+
+static void __init imx28_timer_init(void)
+{
+ mx28_clocks_init();
+}
+
+static struct sys_timer imx28_timer = {
+ .init = imx28_timer_init,
+};
+
+static void __init imx28_evk_init(void)
+{
+ struct clk *clk;
+
+ /* Enable fec phy clock */
+ clk = clk_get_sys("enet_out", NULL);
+ if (!IS_ERR(clk))
+ clk_prepare_enable(clk);
+}
+
+static void __init mxs_machine_init(void)
+{
+ if (of_machine_is_compatible("fsl,imx28-evk"))
+ imx28_evk_init();
+
+ of_platform_populate(NULL, of_default_bus_match_table,
+ NULL, NULL);
+}
+
+static const char *imx23_dt_compat[] __initdata = {
+ "fsl,imx23-evk",
+ "fsl,imx23",
+ NULL,
+};
+
+static const char *imx28_dt_compat[] __initdata = {
+ "fsl,imx28-evk",
+ "fsl,imx28",
+ NULL,
+};
+
+DT_MACHINE_START(IMX23, "Freescale i.MX23 (Device Tree)")
+ .map_io = mx23_map_io,
+ .init_irq = mxs_dt_init_irq,
+ .timer = &imx23_timer,
+ .init_machine = mxs_machine_init,
+ .dt_compat = imx23_dt_compat,
+ .restart = mxs_restart,
+MACHINE_END
+
+DT_MACHINE_START(IMX28, "Freescale i.MX28 (Device Tree)")
+ .map_io = mx28_map_io,
+ .init_irq = mxs_dt_init_irq,
+ .timer = &imx28_timer,
+ .init_machine = mxs_machine_init,
+ .dt_compat = imx28_dt_compat,
+ .restart = mxs_restart,
+MACHINE_END
void __init mx23_soc_init(void)
{
pinctrl_provide_dummies();
+
+ mxs_add_dma("imx23-dma-apbh", MX23_APBH_DMA_BASE_ADDR);
+ mxs_add_dma("imx23-dma-apbx", MX23_APBX_DMA_BASE_ADDR);
+
+ mxs_add_gpio("imx23-gpio", 0, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO0);
+ mxs_add_gpio("imx23-gpio", 1, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO1);
+ mxs_add_gpio("imx23-gpio", 2, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO2);
}
void __init mx28_soc_init(void)
{
pinctrl_provide_dummies();
+
+ mxs_add_dma("imx28-dma-apbh", MX23_APBH_DMA_BASE_ADDR);
+ mxs_add_dma("imx28-dma-apbx", MX23_APBX_DMA_BASE_ADDR);
+
+ mxs_add_gpio("imx28-gpio", 0, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO0);
+ mxs_add_gpio("imx28-gpio", 1, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO1);
+ mxs_add_gpio("imx28-gpio", 2, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO2);
+ mxs_add_gpio("imx28-gpio", 3, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO3);
+ mxs_add_gpio("imx28-gpio", 4, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO4);
}
#define UART_PADDR MX51_UART1_BASE_ADDR
#elif defined (CONFIG_DEBUG_IMX50_IMX53_UART)
#define UART_PADDR MX53_UART1_BASE_ADDR
+#elif defined (CONFIG_DEBUG_IMX6Q_UART2)
+#define UART_PADDR MX6Q_UART2_BASE_ADDR
#elif defined (CONFIG_DEBUG_IMX6Q_UART4)
#define UART_PADDR MX6Q_UART4_BASE_ADDR
#endif
#define MX6Q_CCM_SIZE 0x4000
#define MX6Q_ANATOP_BASE_ADDR 0x020c8000
#define MX6Q_ANATOP_SIZE 0x1000
+#define MX6Q_UART2_BASE_ADDR 0x021e8000
+#define MX6Q_UART2_SIZE 0x4000
#define MX6Q_UART4_BASE_ADDR 0x021f0000
#define MX6Q_UART4_SIZE 0x4000
};
static struct clk_lookup hbus_lookups[] __initdata = {
- { .dev_id = "mxs-dma-apbh", },
+ { .dev_id = "imx23-dma-apbh", },
{ .dev_id = "80004000.dma-apbh", },
};
static struct clk_lookup xbus_lookups[] __initdata = {
{ .dev_id = "duart", .con_id = "apb_pclk"},
- { .dev_id = "mxs-dma-apbx", },
+ { .dev_id = "80070000.serial", .con_id = "apb_pclk"},
+ { .dev_id = "imx23-dma-apbx", },
{ .dev_id = "80024000.dma-apbx", },
};
static struct clk_lookup ssp_lookups[] __initdata = {
- { .dev_id = "mxs-mmc.0", },
- { .dev_id = "mxs-mmc.1", },
+ { .dev_id = "imx23-mmc.0", },
+ { .dev_id = "imx23-mmc.1", },
{ .dev_id = "80010000.ssp", },
{ .dev_id = "80034000.ssp", },
};
};
static struct clk_lookup hbus_lookups[] __initdata = {
- { .dev_id = "mxs-dma-apbh", },
+ { .dev_id = "imx28-dma-apbh", },
{ .dev_id = "80004000.dma-apbh", },
};
static struct clk_lookup xbus_lookups[] __initdata = {
{ .dev_id = "duart", .con_id = "apb_pclk"},
- { .dev_id = "mxs-dma-apbx", },
+ { .dev_id = "80074000.serial", .con_id = "apb_pclk"},
+ { .dev_id = "imx28-dma-apbx", },
{ .dev_id = "80024000.dma-apbx", },
};
static struct clk_lookup ssp0_lookups[] __initdata = {
- { .dev_id = "mxs-mmc.0", },
+ { .dev_id = "imx28-mmc.0", },
{ .dev_id = "80010000.ssp", },
};
static struct clk_lookup ssp1_lookups[] __initdata = {
- { .dev_id = "mxs-mmc.1", },
+ { .dev_id = "imx28-mmc.1", },
{ .dev_id = "80012000.ssp", },
};
static struct clk_lookup ssp2_lookups[] __initdata = {
- { .dev_id = "mxs-mmc.2", },
+ { .dev_id = "imx28-mmc.2", },
{ .dev_id = "80014000.ssp", },
};
static struct clk_lookup ssp3_lookups[] __initdata = {
- { .dev_id = "mxs-mmc.3", },
+ { .dev_id = "imx28-mmc.3", },
{ .dev_id = "80016000.ssp", },
};
config MXS_DMA
bool "MXS DMA support"
depends on SOC_IMX23 || SOC_IMX28
+ select STMP_DEVICE
select DMA_ENGINE
help
Support the MXS DMA engine. This engine including APBH-DMA
#include <linux/platform_device.h>
#include <linux/dmaengine.h>
#include <linux/delay.h>
+#include <linux/module.h>
#include <linux/fsl/mxs-dma.h>
+#include <linux/stmp_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <asm/irq.h>
#include <mach/mxs.h>
-#include <mach/common.h>
#include "dmaengine.h"
* dma can program the controller registers of peripheral devices.
*/
-#define MXS_DMA_APBH 0
-#define MXS_DMA_APBX 1
-#define dma_is_apbh() (mxs_dma->dev_id == MXS_DMA_APBH)
-
-#define APBH_VERSION_LATEST 3
-#define apbh_is_old() (mxs_dma->version < APBH_VERSION_LATEST)
+#define dma_is_apbh(mxs_dma) ((mxs_dma)->type == MXS_DMA_APBH)
+#define apbh_is_old(mxs_dma) ((mxs_dma)->dev_id == IMX23_DMA)
#define HW_APBHX_CTRL0 0x000
#define BM_APBH_CTRL0_APB_BURST8_EN (1 << 29)
#define HW_APBHX_CTRL2 0x020
#define HW_APBHX_CHANNEL_CTRL 0x030
#define BP_APBHX_CHANNEL_CTRL_RESET_CHANNEL 16
-#define HW_APBH_VERSION (cpu_is_mx23() ? 0x3f0 : 0x800)
-#define HW_APBX_VERSION 0x800
-#define BP_APBHX_VERSION_MAJOR 24
-#define HW_APBHX_CHn_NXTCMDAR(n) \
- (((dma_is_apbh() && apbh_is_old()) ? 0x050 : 0x110) + (n) * 0x70)
-#define HW_APBHX_CHn_SEMA(n) \
- (((dma_is_apbh() && apbh_is_old()) ? 0x080 : 0x140) + (n) * 0x70)
+/*
+ * The offset of NXTCMDAR register is different per both dma type and version,
+ * while stride for each channel is all the same 0x70.
+ */
+#define HW_APBHX_CHn_NXTCMDAR(d, n) \
+ (((dma_is_apbh(d) && apbh_is_old(d)) ? 0x050 : 0x110) + (n) * 0x70)
+#define HW_APBHX_CHn_SEMA(d, n) \
+ (((dma_is_apbh(d) && apbh_is_old(d)) ? 0x080 : 0x140) + (n) * 0x70)
/*
* ccw bits definitions
#define MXS_DMA_CHANNELS 16
#define MXS_DMA_CHANNELS_MASK 0xffff
+enum mxs_dma_devtype {
+ MXS_DMA_APBH,
+ MXS_DMA_APBX,
+};
+
+enum mxs_dma_id {
+ IMX23_DMA,
+ IMX28_DMA,
+};
+
struct mxs_dma_engine {
- int dev_id;
- unsigned int version;
+ enum mxs_dma_id dev_id;
+ enum mxs_dma_devtype type;
void __iomem *base;
struct clk *clk;
struct dma_device dma_device;
struct mxs_dma_chan mxs_chans[MXS_DMA_CHANNELS];
};
+struct mxs_dma_type {
+ enum mxs_dma_id id;
+ enum mxs_dma_devtype type;
+};
+
+static struct mxs_dma_type mxs_dma_types[] = {
+ {
+ .id = IMX23_DMA,
+ .type = MXS_DMA_APBH,
+ }, {
+ .id = IMX23_DMA,
+ .type = MXS_DMA_APBX,
+ }, {
+ .id = IMX28_DMA,
+ .type = MXS_DMA_APBH,
+ }, {
+ .id = IMX28_DMA,
+ .type = MXS_DMA_APBX,
+ }
+};
+
+static struct platform_device_id mxs_dma_ids[] = {
+ {
+ .name = "imx23-dma-apbh",
+ .driver_data = (kernel_ulong_t) &mxs_dma_types[0],
+ }, {
+ .name = "imx23-dma-apbx",
+ .driver_data = (kernel_ulong_t) &mxs_dma_types[1],
+ }, {
+ .name = "imx28-dma-apbh",
+ .driver_data = (kernel_ulong_t) &mxs_dma_types[2],
+ }, {
+ .name = "imx28-dma-apbx",
+ .driver_data = (kernel_ulong_t) &mxs_dma_types[3],
+ }, {
+ /* end of list */
+ }
+};
+
+static const struct of_device_id mxs_dma_dt_ids[] = {
+ { .compatible = "fsl,imx23-dma-apbh", .data = &mxs_dma_ids[0], },
+ { .compatible = "fsl,imx23-dma-apbx", .data = &mxs_dma_ids[1], },
+ { .compatible = "fsl,imx28-dma-apbh", .data = &mxs_dma_ids[2], },
+ { .compatible = "fsl,imx28-dma-apbx", .data = &mxs_dma_ids[3], },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_dma_dt_ids);
+
+static struct mxs_dma_chan *to_mxs_dma_chan(struct dma_chan *chan)
+{
+ return container_of(chan, struct mxs_dma_chan, chan);
+}
+
+int mxs_dma_is_apbh(struct dma_chan *chan)
+{
+ struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+ struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+
+ return dma_is_apbh(mxs_dma);
+}
+
+int mxs_dma_is_apbx(struct dma_chan *chan)
+{
+ struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+ struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+
+ return !dma_is_apbh(mxs_dma);
+}
+
static void mxs_dma_reset_chan(struct mxs_dma_chan *mxs_chan)
{
struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
int chan_id = mxs_chan->chan.chan_id;
- if (dma_is_apbh() && apbh_is_old())
+ if (dma_is_apbh(mxs_dma) && apbh_is_old(mxs_dma))
writel(1 << (chan_id + BP_APBH_CTRL0_RESET_CHANNEL),
- mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
else
writel(1 << (chan_id + BP_APBHX_CHANNEL_CTRL_RESET_CHANNEL),
- mxs_dma->base + HW_APBHX_CHANNEL_CTRL + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CHANNEL_CTRL + STMP_OFFSET_REG_SET);
}
static void mxs_dma_enable_chan(struct mxs_dma_chan *mxs_chan)
/* set cmd_addr up */
writel(mxs_chan->ccw_phys,
- mxs_dma->base + HW_APBHX_CHn_NXTCMDAR(chan_id));
+ mxs_dma->base + HW_APBHX_CHn_NXTCMDAR(mxs_dma, chan_id));
/* write 1 to SEMA to kick off the channel */
- writel(1, mxs_dma->base + HW_APBHX_CHn_SEMA(chan_id));
+ writel(1, mxs_dma->base + HW_APBHX_CHn_SEMA(mxs_dma, chan_id));
}
static void mxs_dma_disable_chan(struct mxs_dma_chan *mxs_chan)
int chan_id = mxs_chan->chan.chan_id;
/* freeze the channel */
- if (dma_is_apbh() && apbh_is_old())
+ if (dma_is_apbh(mxs_dma) && apbh_is_old(mxs_dma))
writel(1 << chan_id,
- mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
else
writel(1 << chan_id,
- mxs_dma->base + HW_APBHX_CHANNEL_CTRL + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CHANNEL_CTRL + STMP_OFFSET_REG_SET);
mxs_chan->status = DMA_PAUSED;
}
int chan_id = mxs_chan->chan.chan_id;
/* unfreeze the channel */
- if (dma_is_apbh() && apbh_is_old())
+ if (dma_is_apbh(mxs_dma) && apbh_is_old(mxs_dma))
writel(1 << chan_id,
- mxs_dma->base + HW_APBHX_CTRL0 + MXS_CLR_ADDR);
+ mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_CLR);
else
writel(1 << chan_id,
- mxs_dma->base + HW_APBHX_CHANNEL_CTRL + MXS_CLR_ADDR);
+ mxs_dma->base + HW_APBHX_CHANNEL_CTRL + STMP_OFFSET_REG_CLR);
mxs_chan->status = DMA_IN_PROGRESS;
}
-static struct mxs_dma_chan *to_mxs_dma_chan(struct dma_chan *chan)
-{
- return container_of(chan, struct mxs_dma_chan, chan);
-}
-
static dma_cookie_t mxs_dma_tx_submit(struct dma_async_tx_descriptor *tx)
{
return dma_cookie_assign(tx);
/* completion status */
stat1 = readl(mxs_dma->base + HW_APBHX_CTRL1);
stat1 &= MXS_DMA_CHANNELS_MASK;
- writel(stat1, mxs_dma->base + HW_APBHX_CTRL1 + MXS_CLR_ADDR);
+ writel(stat1, mxs_dma->base + HW_APBHX_CTRL1 + STMP_OFFSET_REG_CLR);
/* error status */
stat2 = readl(mxs_dma->base + HW_APBHX_CTRL2);
- writel(stat2, mxs_dma->base + HW_APBHX_CTRL2 + MXS_CLR_ADDR);
+ writel(stat2, mxs_dma->base + HW_APBHX_CTRL2 + STMP_OFFSET_REG_CLR);
/*
* When both completion and error of termination bits set at the
if (ret)
return ret;
- ret = mxs_reset_block(mxs_dma->base);
+ ret = stmp_reset_block(mxs_dma->base);
if (ret)
goto err_out;
- /* only major version matters */
- mxs_dma->version = readl(mxs_dma->base +
- ((mxs_dma->dev_id == MXS_DMA_APBX) ?
- HW_APBX_VERSION : HW_APBH_VERSION)) >>
- BP_APBHX_VERSION_MAJOR;
-
/* enable apbh burst */
- if (dma_is_apbh()) {
+ if (dma_is_apbh(mxs_dma)) {
writel(BM_APBH_CTRL0_APB_BURST_EN,
- mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
writel(BM_APBH_CTRL0_APB_BURST8_EN,
- mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
}
/* enable irq for all the channels */
writel(MXS_DMA_CHANNELS_MASK << MXS_DMA_CHANNELS,
- mxs_dma->base + HW_APBHX_CTRL1 + MXS_SET_ADDR);
+ mxs_dma->base + HW_APBHX_CTRL1 + STMP_OFFSET_REG_SET);
err_out:
clk_disable_unprepare(mxs_dma->clk);
static int __init mxs_dma_probe(struct platform_device *pdev)
{
- const struct platform_device_id *id_entry =
- platform_get_device_id(pdev);
+ const struct platform_device_id *id_entry;
+ const struct of_device_id *of_id;
+ const struct mxs_dma_type *dma_type;
struct mxs_dma_engine *mxs_dma;
struct resource *iores;
int ret, i;
if (!mxs_dma)
return -ENOMEM;
- mxs_dma->dev_id = id_entry->driver_data;
+ of_id = of_match_device(mxs_dma_dt_ids, &pdev->dev);
+ if (of_id)
+ id_entry = of_id->data;
+ else
+ id_entry = platform_get_device_id(pdev);
+
+ dma_type = (struct mxs_dma_type *)id_entry->driver_data;
+ mxs_dma->type = dma_type->type;
+ mxs_dma->dev_id = dma_type->id;
iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
return ret;
}
-static struct platform_device_id mxs_dma_type[] = {
- {
- .name = "mxs-dma-apbh",
- .driver_data = MXS_DMA_APBH,
- }, {
- .name = "mxs-dma-apbx",
- .driver_data = MXS_DMA_APBX,
- }, {
- /* end of list */
- }
-};
-
static struct platform_driver mxs_dma_driver = {
.driver = {
.name = "mxs-dma",
+ .of_match_table = mxs_dma_dt_ids,
},
- .id_table = mxs_dma_type,
+ .id_table = mxs_dma_ids,
};
static int __init mxs_dma_module_init(void)
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/basic_mmio_gpio.h>
#include <linux/module.h>
-#include <mach/mxs.h>
#define MXS_SET 0x4
#define MXS_CLR 0x8
-#define PINCTRL_DOUT(n) ((cpu_is_mx23() ? 0x0500 : 0x0700) + (n) * 0x10)
-#define PINCTRL_DIN(n) ((cpu_is_mx23() ? 0x0600 : 0x0900) + (n) * 0x10)
-#define PINCTRL_DOE(n) ((cpu_is_mx23() ? 0x0700 : 0x0b00) + (n) * 0x10)
-#define PINCTRL_PIN2IRQ(n) ((cpu_is_mx23() ? 0x0800 : 0x1000) + (n) * 0x10)
-#define PINCTRL_IRQEN(n) ((cpu_is_mx23() ? 0x0900 : 0x1100) + (n) * 0x10)
-#define PINCTRL_IRQLEV(n) ((cpu_is_mx23() ? 0x0a00 : 0x1200) + (n) * 0x10)
-#define PINCTRL_IRQPOL(n) ((cpu_is_mx23() ? 0x0b00 : 0x1300) + (n) * 0x10)
-#define PINCTRL_IRQSTAT(n) ((cpu_is_mx23() ? 0x0c00 : 0x1400) + (n) * 0x10)
+#define PINCTRL_DOUT(p) ((is_imx23_gpio(p) ? 0x0500 : 0x0700) + (p->id) * 0x10)
+#define PINCTRL_DIN(p) ((is_imx23_gpio(p) ? 0x0600 : 0x0900) + (p->id) * 0x10)
+#define PINCTRL_DOE(p) ((is_imx23_gpio(p) ? 0x0700 : 0x0b00) + (p->id) * 0x10)
+#define PINCTRL_PIN2IRQ(p) ((is_imx23_gpio(p) ? 0x0800 : 0x1000) + (p->id) * 0x10)
+#define PINCTRL_IRQEN(p) ((is_imx23_gpio(p) ? 0x0900 : 0x1100) + (p->id) * 0x10)
+#define PINCTRL_IRQLEV(p) ((is_imx23_gpio(p) ? 0x0a00 : 0x1200) + (p->id) * 0x10)
+#define PINCTRL_IRQPOL(p) ((is_imx23_gpio(p) ? 0x0b00 : 0x1300) + (p->id) * 0x10)
+#define PINCTRL_IRQSTAT(p) ((is_imx23_gpio(p) ? 0x0c00 : 0x1400) + (p->id) * 0x10)
#define GPIO_INT_FALL_EDGE 0x0
#define GPIO_INT_LOW_LEV 0x1
#define irq_to_gpio(irq) ((irq) - MXS_GPIO_IRQ_START)
+enum mxs_gpio_id {
+ IMX23_GPIO,
+ IMX28_GPIO,
+};
+
struct mxs_gpio_port {
void __iomem *base;
int id;
int irq;
int virtual_irq_start;
struct bgpio_chip bgc;
+ enum mxs_gpio_id devid;
};
+static inline int is_imx23_gpio(struct mxs_gpio_port *port)
+{
+ return port->devid == IMX23_GPIO;
+}
+
+static inline int is_imx28_gpio(struct mxs_gpio_port *port)
+{
+ return port->devid == IMX28_GPIO;
+}
+
/* Note: This driver assumes 32 GPIOs are handled in one register */
static int mxs_gpio_set_irq_type(struct irq_data *d, unsigned int type)
}
/* set level or edge */
- pin_addr = port->base + PINCTRL_IRQLEV(port->id);
+ pin_addr = port->base + PINCTRL_IRQLEV(port);
if (edge & GPIO_INT_LEV_MASK)
writel(pin_mask, pin_addr + MXS_SET);
else
writel(pin_mask, pin_addr + MXS_CLR);
/* set polarity */
- pin_addr = port->base + PINCTRL_IRQPOL(port->id);
+ pin_addr = port->base + PINCTRL_IRQPOL(port);
if (edge & GPIO_INT_POL_MASK)
writel(pin_mask, pin_addr + MXS_SET);
else
writel(pin_mask, pin_addr + MXS_CLR);
writel(1 << (gpio & 0x1f),
- port->base + PINCTRL_IRQSTAT(port->id) + MXS_CLR);
+ port->base + PINCTRL_IRQSTAT(port) + MXS_CLR);
return 0;
}
desc->irq_data.chip->irq_ack(&desc->irq_data);
- irq_stat = readl(port->base + PINCTRL_IRQSTAT(port->id)) &
- readl(port->base + PINCTRL_IRQEN(port->id));
+ irq_stat = readl(port->base + PINCTRL_IRQSTAT(port)) &
+ readl(port->base + PINCTRL_IRQEN(port));
while (irq_stat != 0) {
int irqoffset = fls(irq_stat) - 1;
ct->chip.irq_unmask = irq_gc_mask_set_bit;
ct->chip.irq_set_type = mxs_gpio_set_irq_type;
ct->chip.irq_set_wake = mxs_gpio_set_wake_irq;
- ct->regs.ack = PINCTRL_IRQSTAT(port->id) + MXS_CLR;
- ct->regs.mask = PINCTRL_IRQEN(port->id);
+ ct->regs.ack = PINCTRL_IRQSTAT(port) + MXS_CLR;
+ ct->regs.mask = PINCTRL_IRQEN(port);
irq_setup_generic_chip(gc, IRQ_MSK(32), 0, IRQ_NOREQUEST, 0);
}
return port->virtual_irq_start + offset;
}
+static struct platform_device_id mxs_gpio_ids[] = {
+ {
+ .name = "imx23-gpio",
+ .driver_data = IMX23_GPIO,
+ }, {
+ .name = "imx28-gpio",
+ .driver_data = IMX28_GPIO,
+ }, {
+ /* sentinel */
+ }
+};
+MODULE_DEVICE_TABLE(platform, mxs_gpio_ids);
+
+static const struct of_device_id mxs_gpio_dt_ids[] = {
+ { .compatible = "fsl,imx23-gpio", .data = (void *) IMX23_GPIO, },
+ { .compatible = "fsl,imx28-gpio", .data = (void *) IMX28_GPIO, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_gpio_dt_ids);
+
static int __devinit mxs_gpio_probe(struct platform_device *pdev)
{
+ const struct of_device_id *of_id =
+ of_match_device(mxs_gpio_dt_ids, &pdev->dev);
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *parent;
static void __iomem *base;
struct mxs_gpio_port *port;
struct resource *iores = NULL;
int err;
- port = kzalloc(sizeof(struct mxs_gpio_port), GFP_KERNEL);
+ port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
if (!port)
return -ENOMEM;
- port->id = pdev->id;
+ if (np) {
+ port->id = of_alias_get_id(np, "gpio");
+ if (port->id < 0)
+ return port->id;
+ port->devid = (enum mxs_gpio_id) of_id->data;
+ } else {
+ port->id = pdev->id;
+ port->devid = pdev->id_entry->driver_data;
+ }
port->virtual_irq_start = MXS_GPIO_IRQ_START + port->id * 32;
+ port->irq = platform_get_irq(pdev, 0);
+ if (port->irq < 0)
+ return port->irq;
+
/*
* map memory region only once, as all the gpio ports
* share the same one
*/
if (!base) {
- iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!iores) {
- err = -ENODEV;
- goto out_kfree;
- }
-
- if (!request_mem_region(iores->start, resource_size(iores),
- pdev->name)) {
- err = -EBUSY;
- goto out_kfree;
- }
-
- base = ioremap(iores->start, resource_size(iores));
- if (!base) {
- err = -ENOMEM;
- goto out_release_mem;
+ if (np) {
+ parent = of_get_parent(np);
+ base = of_iomap(parent, 0);
+ of_node_put(parent);
+ } else {
+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_request_and_ioremap(&pdev->dev, iores);
}
+ if (!base)
+ return -EADDRNOTAVAIL;
}
port->base = base;
- port->irq = platform_get_irq(pdev, 0);
- if (port->irq < 0) {
- err = -EINVAL;
- goto out_iounmap;
- }
-
/*
* select the pin interrupt functionality but initially
* disable the interrupts
*/
- writel(~0U, port->base + PINCTRL_PIN2IRQ(port->id));
- writel(0, port->base + PINCTRL_IRQEN(port->id));
+ writel(~0U, port->base + PINCTRL_PIN2IRQ(port));
+ writel(0, port->base + PINCTRL_IRQEN(port));
/* clear address has to be used to clear IRQSTAT bits */
- writel(~0U, port->base + PINCTRL_IRQSTAT(port->id) + MXS_CLR);
+ writel(~0U, port->base + PINCTRL_IRQSTAT(port) + MXS_CLR);
/* gpio-mxs can be a generic irq chip */
mxs_gpio_init_gc(port);
irq_set_handler_data(port->irq, port);
err = bgpio_init(&port->bgc, &pdev->dev, 4,
- port->base + PINCTRL_DIN(port->id),
- port->base + PINCTRL_DOUT(port->id), NULL,
- port->base + PINCTRL_DOE(port->id), NULL, 0);
+ port->base + PINCTRL_DIN(port),
+ port->base + PINCTRL_DOUT(port), NULL,
+ port->base + PINCTRL_DOE(port), NULL, 0);
if (err)
- goto out_iounmap;
+ return err;
port->bgc.gc.to_irq = mxs_gpio_to_irq;
port->bgc.gc.base = port->id * 32;
err = gpiochip_add(&port->bgc.gc);
- if (err)
- goto out_bgpio_remove;
+ if (err) {
+ bgpio_remove(&port->bgc);
+ return err;
+ }
return 0;
-
-out_bgpio_remove:
- bgpio_remove(&port->bgc);
-out_iounmap:
- if (iores)
- iounmap(port->base);
-out_release_mem:
- if (iores)
- release_mem_region(iores->start, resource_size(iores));
-out_kfree:
- kfree(port);
- dev_info(&pdev->dev, "%s failed with errno %d\n", __func__, err);
- return err;
}
static struct platform_driver mxs_gpio_driver = {
.driver = {
.name = "gpio-mxs",
.owner = THIS_MODULE,
+ .of_match_table = mxs_gpio_dt_ids,
},
.probe = mxs_gpio_probe,
+ .id_table = mxs_gpio_ids,
};
static int __init mxs_gpio_init(void)
#include <linux/io.h>
#include <linux/pinctrl/consumer.h>
#include <linux/stmp_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_i2c.h>
#define DRIVER_NAME "mxs-i2c"
adap->algo = &mxs_i2c_algo;
adap->dev.parent = dev;
adap->nr = pdev->id;
+ adap->dev.of_node = pdev->dev.of_node;
i2c_set_adapdata(adap, i2c);
err = i2c_add_numbered_adapter(adap);
if (err) {
return err;
}
+ of_i2c_register_devices(adap);
+
return 0;
}
return 0;
}
+static const struct of_device_id mxs_i2c_dt_ids[] = {
+ { .compatible = "fsl,imx28-i2c", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_i2c_dt_ids);
+
static struct platform_driver mxs_i2c_driver = {
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
+ .of_match_table = mxs_i2c_dt_ids,
},
.remove = __devexit_p(mxs_i2c_remove),
};
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/ioport.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/fsl/mxs-dma.h>
#include <linux/pinctrl/consumer.h>
-
-#include <mach/mxs.h>
-#include <mach/common.h>
-#include <mach/mmc.h>
+#include <linux/stmp_device.h>
+#include <linux/mmc/mxs-mmc.h>
#define DRIVER_NAME "mxs-mmc"
/* card detect polling timeout */
#define MXS_MMC_DETECT_TIMEOUT (HZ/2)
-#define SSP_VERSION_LATEST 4
-#define ssp_is_old() (host->version < SSP_VERSION_LATEST)
+#define ssp_is_old(host) ((host)->devid == IMX23_MMC)
/* SSP registers */
#define HW_SSP_CTRL0 0x000
#define BM_SSP_BLOCK_SIZE_BLOCK_COUNT (0xffffff << 4)
#define BP_SSP_BLOCK_SIZE_BLOCK_SIZE (0)
#define BM_SSP_BLOCK_SIZE_BLOCK_SIZE (0xf)
-#define HW_SSP_TIMING (ssp_is_old() ? 0x050 : 0x070)
+#define HW_SSP_TIMING(h) (ssp_is_old(h) ? 0x050 : 0x070)
#define BP_SSP_TIMING_TIMEOUT (16)
#define BM_SSP_TIMING_TIMEOUT (0xffff << 16)
#define BP_SSP_TIMING_CLOCK_DIVIDE (8)
#define BM_SSP_TIMING_CLOCK_DIVIDE (0xff << 8)
#define BP_SSP_TIMING_CLOCK_RATE (0)
#define BM_SSP_TIMING_CLOCK_RATE (0xff)
-#define HW_SSP_CTRL1 (ssp_is_old() ? 0x060 : 0x080)
+#define HW_SSP_CTRL1(h) (ssp_is_old(h) ? 0x060 : 0x080)
#define BM_SSP_CTRL1_SDIO_IRQ (1 << 31)
#define BM_SSP_CTRL1_SDIO_IRQ_EN (1 << 30)
#define BM_SSP_CTRL1_RESP_ERR_IRQ (1 << 29)
#define BM_SSP_CTRL1_WORD_LENGTH (0xf << 4)
#define BP_SSP_CTRL1_SSP_MODE (0)
#define BM_SSP_CTRL1_SSP_MODE (0xf)
-#define HW_SSP_SDRESP0 (ssp_is_old() ? 0x080 : 0x0a0)
-#define HW_SSP_SDRESP1 (ssp_is_old() ? 0x090 : 0x0b0)
-#define HW_SSP_SDRESP2 (ssp_is_old() ? 0x0a0 : 0x0c0)
-#define HW_SSP_SDRESP3 (ssp_is_old() ? 0x0b0 : 0x0d0)
-#define HW_SSP_STATUS (ssp_is_old() ? 0x0c0 : 0x100)
+#define HW_SSP_SDRESP0(h) (ssp_is_old(h) ? 0x080 : 0x0a0)
+#define HW_SSP_SDRESP1(h) (ssp_is_old(h) ? 0x090 : 0x0b0)
+#define HW_SSP_SDRESP2(h) (ssp_is_old(h) ? 0x0a0 : 0x0c0)
+#define HW_SSP_SDRESP3(h) (ssp_is_old(h) ? 0x0b0 : 0x0d0)
+#define HW_SSP_STATUS(h) (ssp_is_old(h) ? 0x0c0 : 0x100)
#define BM_SSP_STATUS_CARD_DETECT (1 << 28)
#define BM_SSP_STATUS_SDIO_IRQ (1 << 17)
-#define HW_SSP_VERSION (cpu_is_mx23() ? 0x110 : 0x130)
-#define BP_SSP_VERSION_MAJOR (24)
#define BF_SSP(value, field) (((value) << BP_SSP_##field) & BM_SSP_##field)
#define SSP_PIO_NUM 3
+enum mxs_mmc_id {
+ IMX23_MMC,
+ IMX28_MMC,
+};
+
struct mxs_mmc_host {
struct mmc_host *mmc;
struct mmc_request *mrq;
struct mmc_data *data;
void __iomem *base;
- int irq;
- struct resource *res;
- struct resource *dma_res;
+ int dma_channel;
struct clk *clk;
unsigned int clk_rate;
enum dma_transfer_direction slave_dirn;
u32 ssp_pio_words[SSP_PIO_NUM];
- unsigned int version;
+ enum mxs_mmc_id devid;
unsigned char bus_width;
spinlock_t lock;
int sdio_irq_en;
+ int wp_gpio;
};
static int mxs_mmc_get_ro(struct mmc_host *mmc)
{
struct mxs_mmc_host *host = mmc_priv(mmc);
- struct mxs_mmc_platform_data *pdata =
- mmc_dev(host->mmc)->platform_data;
-
- if (!pdata)
- return -EFAULT;
- if (!gpio_is_valid(pdata->wp_gpio))
+ if (!gpio_is_valid(host->wp_gpio))
return -EINVAL;
- return gpio_get_value(pdata->wp_gpio);
+ return gpio_get_value(host->wp_gpio);
}
static int mxs_mmc_get_cd(struct mmc_host *mmc)
{
struct mxs_mmc_host *host = mmc_priv(mmc);
- return !(readl(host->base + HW_SSP_STATUS) &
+ return !(readl(host->base + HW_SSP_STATUS(host)) &
BM_SSP_STATUS_CARD_DETECT);
}
{
u32 ctrl0, ctrl1;
- mxs_reset_block(host->base);
+ stmp_reset_block(host->base);
ctrl0 = BM_SSP_CTRL0_IGNORE_CRC;
ctrl1 = BF_SSP(0x3, CTRL1_SSP_MODE) |
writel(BF_SSP(0xffff, TIMING_TIMEOUT) |
BF_SSP(2, TIMING_CLOCK_DIVIDE) |
BF_SSP(0, TIMING_CLOCK_RATE),
- host->base + HW_SSP_TIMING);
+ host->base + HW_SSP_TIMING(host));
if (host->sdio_irq_en) {
ctrl0 |= BM_SSP_CTRL0_SDIO_IRQ_CHECK;
}
writel(ctrl0, host->base + HW_SSP_CTRL0);
- writel(ctrl1, host->base + HW_SSP_CTRL1);
+ writel(ctrl1, host->base + HW_SSP_CTRL1(host));
}
static void mxs_mmc_start_cmd(struct mxs_mmc_host *host,
if (mmc_resp_type(cmd) & MMC_RSP_PRESENT) {
if (mmc_resp_type(cmd) & MMC_RSP_136) {
- cmd->resp[3] = readl(host->base + HW_SSP_SDRESP0);
- cmd->resp[2] = readl(host->base + HW_SSP_SDRESP1);
- cmd->resp[1] = readl(host->base + HW_SSP_SDRESP2);
- cmd->resp[0] = readl(host->base + HW_SSP_SDRESP3);
+ cmd->resp[3] = readl(host->base + HW_SSP_SDRESP0(host));
+ cmd->resp[2] = readl(host->base + HW_SSP_SDRESP1(host));
+ cmd->resp[1] = readl(host->base + HW_SSP_SDRESP2(host));
+ cmd->resp[0] = readl(host->base + HW_SSP_SDRESP3(host));
} else {
- cmd->resp[0] = readl(host->base + HW_SSP_SDRESP0);
+ cmd->resp[0] = readl(host->base + HW_SSP_SDRESP0(host));
}
}
spin_lock(&host->lock);
- stat = readl(host->base + HW_SSP_CTRL1);
+ stat = readl(host->base + HW_SSP_CTRL1(host));
writel(stat & MXS_MMC_IRQ_BITS,
- host->base + HW_SSP_CTRL1 + MXS_CLR_ADDR);
+ host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
if ((stat & BM_SSP_CTRL1_SDIO_IRQ) && (stat & BM_SSP_CTRL1_SDIO_IRQ_EN))
mmc_signal_sdio_irq(host->mmc);
blocks = 1;
/* xfer count, block size and count need to be set differently */
- if (ssp_is_old()) {
+ if (ssp_is_old(host)) {
ctrl0 |= BF_SSP(data_size, CTRL0_XFER_COUNT);
cmd0 |= BF_SSP(log2_blksz, CMD0_BLOCK_SIZE) |
BF_SSP(blocks - 1, CMD0_BLOCK_COUNT);
/* set the timeout count */
timeout = mxs_ns_to_ssp_ticks(host->clk_rate, data->timeout_ns);
- val = readl(host->base + HW_SSP_TIMING);
+ val = readl(host->base + HW_SSP_TIMING(host));
val &= ~(BM_SSP_TIMING_TIMEOUT);
val |= BF_SSP(timeout, TIMING_TIMEOUT);
- writel(val, host->base + HW_SSP_TIMING);
+ writel(val, host->base + HW_SSP_TIMING(host));
/* pio */
host->ssp_pio_words[0] = ctrl0;
ssp_sck = ssp_clk / clock_divide / (1 + clock_rate);
- val = readl(host->base + HW_SSP_TIMING);
+ val = readl(host->base + HW_SSP_TIMING(host));
val &= ~(BM_SSP_TIMING_CLOCK_DIVIDE | BM_SSP_TIMING_CLOCK_RATE);
val |= BF_SSP(clock_divide, TIMING_CLOCK_DIVIDE);
val |= BF_SSP(clock_rate, TIMING_CLOCK_RATE);
- writel(val, host->base + HW_SSP_TIMING);
+ writel(val, host->base + HW_SSP_TIMING(host));
host->clk_rate = ssp_sck;
if (enable) {
writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
- host->base + HW_SSP_CTRL0 + MXS_SET_ADDR);
+ host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET);
writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
- host->base + HW_SSP_CTRL1 + MXS_SET_ADDR);
+ host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_SET);
- if (readl(host->base + HW_SSP_STATUS) & BM_SSP_STATUS_SDIO_IRQ)
+ if (readl(host->base + HW_SSP_STATUS(host)) &
+ BM_SSP_STATUS_SDIO_IRQ)
mmc_signal_sdio_irq(host->mmc);
} else {
writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
- host->base + HW_SSP_CTRL0 + MXS_CLR_ADDR);
+ host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR);
writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
- host->base + HW_SSP_CTRL1 + MXS_CLR_ADDR);
+ host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
}
spin_unlock_irqrestore(&host->lock, flags);
if (!mxs_dma_is_apbh(chan))
return false;
- if (chan->chan_id != host->dma_res->start)
+ if (chan->chan_id != host->dma_channel)
return false;
chan->private = &host->dma_data;
return true;
}
+static struct platform_device_id mxs_mmc_ids[] = {
+ {
+ .name = "imx23-mmc",
+ .driver_data = IMX23_MMC,
+ }, {
+ .name = "imx28-mmc",
+ .driver_data = IMX28_MMC,
+ }, {
+ /* sentinel */
+ }
+};
+MODULE_DEVICE_TABLE(platform, mxs_mmc_ids);
+
+static const struct of_device_id mxs_mmc_dt_ids[] = {
+ { .compatible = "fsl,imx23-mmc", .data = (void *) IMX23_MMC, },
+ { .compatible = "fsl,imx28-mmc", .data = (void *) IMX28_MMC, },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_mmc_dt_ids);
+
static int mxs_mmc_probe(struct platform_device *pdev)
{
+ const struct of_device_id *of_id =
+ of_match_device(mxs_mmc_dt_ids, &pdev->dev);
+ struct device_node *np = pdev->dev.of_node;
struct mxs_mmc_host *host;
struct mmc_host *mmc;
- struct resource *iores, *dmares, *r;
+ struct resource *iores, *dmares;
struct mxs_mmc_platform_data *pdata;
struct pinctrl *pinctrl;
int ret = 0, irq_err, irq_dma;
dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
irq_err = platform_get_irq(pdev, 0);
irq_dma = platform_get_irq(pdev, 1);
- if (!iores || !dmares || irq_err < 0 || irq_dma < 0)
+ if (!iores || irq_err < 0 || irq_dma < 0)
return -EINVAL;
- r = request_mem_region(iores->start, resource_size(iores), pdev->name);
- if (!r)
- return -EBUSY;
-
mmc = mmc_alloc_host(sizeof(struct mxs_mmc_host), &pdev->dev);
- if (!mmc) {
- ret = -ENOMEM;
- goto out_release_mem;
- }
+ if (!mmc)
+ return -ENOMEM;
host = mmc_priv(mmc);
- host->base = ioremap(r->start, resource_size(r));
+ host->base = devm_request_and_ioremap(&pdev->dev, iores);
if (!host->base) {
- ret = -ENOMEM;
+ ret = -EADDRNOTAVAIL;
goto out_mmc_free;
}
- /* only major verion does matter */
- host->version = readl(host->base + HW_SSP_VERSION) >>
- BP_SSP_VERSION_MAJOR;
+ if (np) {
+ host->devid = (enum mxs_mmc_id) of_id->data;
+ /*
+ * TODO: This is a temporary solution and should be changed
+ * to use generic DMA binding later when the helpers get in.
+ */
+ ret = of_property_read_u32(np, "fsl,ssp-dma-channel",
+ &host->dma_channel);
+ if (ret) {
+ dev_err(mmc_dev(host->mmc),
+ "failed to get dma channel\n");
+ goto out_mmc_free;
+ }
+ } else {
+ host->devid = pdev->id_entry->driver_data;
+ host->dma_channel = dmares->start;
+ }
host->mmc = mmc;
- host->res = r;
- host->dma_res = dmares;
- host->irq = irq_err;
host->sdio_irq_en = 0;
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
if (IS_ERR(pinctrl)) {
ret = PTR_ERR(pinctrl);
- goto out_iounmap;
+ goto out_mmc_free;
}
host->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(host->clk)) {
ret = PTR_ERR(host->clk);
- goto out_iounmap;
+ goto out_mmc_free;
}
clk_prepare_enable(host->clk);
MMC_CAP_SDIO_IRQ | MMC_CAP_NEEDS_POLL;
pdata = mmc_dev(host->mmc)->platform_data;
- if (pdata) {
+ if (!pdata) {
+ u32 bus_width = 0;
+ of_property_read_u32(np, "bus-width", &bus_width);
+ if (bus_width == 4)
+ mmc->caps |= MMC_CAP_4_BIT_DATA;
+ else if (bus_width == 8)
+ mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
+ host->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
+ } else {
if (pdata->flags & SLOTF_8_BIT_CAPABLE)
mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
if (pdata->flags & SLOTF_4_BIT_CAPABLE)
mmc->caps |= MMC_CAP_4_BIT_DATA;
+ host->wp_gpio = pdata->wp_gpio;
}
mmc->f_min = 400000;
mmc->max_segs = 52;
mmc->max_blk_size = 1 << 0xf;
- mmc->max_blk_count = (ssp_is_old()) ? 0xff : 0xffffff;
- mmc->max_req_size = (ssp_is_old()) ? 0xffff : 0xffffffff;
+ mmc->max_blk_count = (ssp_is_old(host)) ? 0xff : 0xffffff;
+ mmc->max_req_size = (ssp_is_old(host)) ? 0xffff : 0xffffffff;
mmc->max_seg_size = dma_get_max_seg_size(host->dmach->device->dev);
platform_set_drvdata(pdev, mmc);
- ret = request_irq(host->irq, mxs_mmc_irq_handler, 0, DRIVER_NAME, host);
+ ret = devm_request_irq(&pdev->dev, irq_err, mxs_mmc_irq_handler, 0,
+ DRIVER_NAME, host);
if (ret)
goto out_free_dma;
ret = mmc_add_host(mmc);
if (ret)
- goto out_free_irq;
+ goto out_free_dma;
dev_info(mmc_dev(host->mmc), "initialized\n");
return 0;
-out_free_irq:
- free_irq(host->irq, host);
out_free_dma:
if (host->dmach)
dma_release_channel(host->dmach);
out_clk_put:
clk_disable_unprepare(host->clk);
clk_put(host->clk);
-out_iounmap:
- iounmap(host->base);
out_mmc_free:
mmc_free_host(mmc);
-out_release_mem:
- release_mem_region(iores->start, resource_size(iores));
return ret;
}
{
struct mmc_host *mmc = platform_get_drvdata(pdev);
struct mxs_mmc_host *host = mmc_priv(mmc);
- struct resource *res = host->res;
mmc_remove_host(mmc);
- free_irq(host->irq, host);
-
platform_set_drvdata(pdev, NULL);
if (host->dmach)
clk_disable_unprepare(host->clk);
clk_put(host->clk);
- iounmap(host->base);
-
mmc_free_host(mmc);
- release_mem_region(res->start, resource_size(res));
-
return 0;
}
static struct platform_driver mxs_mmc_driver = {
.probe = mxs_mmc_probe,
.remove = mxs_mmc_remove,
+ .id_table = mxs_mmc_ids,
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
#ifdef CONFIG_PM
.pm = &mxs_mmc_pm_ops,
+ .of_match_table = mxs_mmc_dt_ids,
#endif
},
};
int chan_irq;
};
-static inline int mxs_dma_is_apbh(struct dma_chan *chan)
-{
- return !strcmp(dev_name(chan->device->dev), "mxs-dma-apbh");
-}
-
-static inline int mxs_dma_is_apbx(struct dma_chan *chan)
-{
- return !strcmp(dev_name(chan->device->dev), "mxs-dma-apbx");
-}
-
+extern int mxs_dma_is_apbh(struct dma_chan *chan);
+extern int mxs_dma_is_apbx(struct dma_chan *chan);
#endif /* __MACH_MXS_DMA_H__ */
--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __LINUX_MMC_MXS_MMC_H__
+#define __LINUX_MMC_MXS_MMC_H__
+
+struct mxs_mmc_platform_data {
+ int wp_gpio; /* write protect pin */
+ unsigned int flags;
+#define SLOTF_4_BIT_CAPABLE (1 << 0)
+#define SLOTF_8_BIT_CAPABLE (1 << 1)
+};
+
+#endif /* __LINUX_MMC_MXS_MMC_H__ */
projects / linux-2.6-block.git / commitdiff