MODULE_DEVICE_TABLE(pci, ast_pciidlist);
+static bool ast_is_vga_enabled(void __iomem *ioregs)
+{
+ u8 vgaer = __ast_read8(ioregs, AST_IO_VGAER);
+
+ return vgaer & AST_IO_VGAER_VGA_ENABLE;
+}
+
+static void ast_enable_vga(void __iomem *ioregs)
+{
+ __ast_write8(ioregs, AST_IO_VGAER, AST_IO_VGAER_VGA_ENABLE);
+ __ast_write8(ioregs, AST_IO_VGAMR_W, AST_IO_VGAMR_IOSEL);
+}
+
+/*
+ * Run this function as part of the HW device cleanup; not
+ * when the DRM device gets released.
+ */
+static void ast_enable_mmio_release(void *data)
+{
+ void __iomem *ioregs = (void __force __iomem *)data;
+
+ /* enable standard VGA decode */
+ __ast_write8_i(ioregs, AST_IO_VGACRI, 0xa1, AST_IO_VGACRA1_MMIO_ENABLED);
+}
+
+static int ast_enable_mmio(struct device *dev, void __iomem *ioregs)
+{
+ void *data = (void __force *)ioregs;
+
+ __ast_write8_i(ioregs, AST_IO_VGACRI, 0xa1,
+ AST_IO_VGACRA1_MMIO_ENABLED |
+ AST_IO_VGACRA1_VGAIO_DISABLED);
+
+ return devm_add_action_or_reset(dev, ast_enable_mmio_release, data);
+}
+
+static void ast_open_key(void __iomem *ioregs)
+{
+ __ast_write8_i(ioregs, AST_IO_VGACRI, 0x80, AST_IO_VGACR80_PASSWORD);
+}
+
+static int ast_detect_chip(struct pci_dev *pdev,
+ void __iomem *regs, void __iomem *ioregs,
+ enum ast_chip *chip_out,
+ enum ast_config_mode *config_mode_out)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ enum ast_config_mode config_mode = ast_use_defaults;
+ uint32_t scu_rev = 0xffffffff;
+ enum ast_chip chip;
+ u32 data;
+ u8 vgacrd0, vgacrd1;
+
+ /*
+ * Find configuration mode and read SCU revision
+ */
+
+ /* Check if we have device-tree properties */
+ if (np && !of_property_read_u32(np, "aspeed,scu-revision-id", &data)) {
+ /* We do, disable P2A access */
+ config_mode = ast_use_dt;
+ scu_rev = data;
+ } else if (pdev->device == PCI_CHIP_AST2000) { // Not all families have a P2A bridge
+ /*
+ * The BMC will set SCU 0x40 D[12] to 1 if the P2 bridge
+ * is disabled. We force using P2A if VGA only mode bit
+ * is set D[7]
+ */
+ vgacrd0 = __ast_read8_i(ioregs, AST_IO_VGACRI, 0xd0);
+ vgacrd1 = __ast_read8_i(ioregs, AST_IO_VGACRI, 0xd1);
+ if (!(vgacrd0 & 0x80) || !(vgacrd1 & 0x10)) {
+
+ /*
+ * We have a P2A bridge and it is enabled.
+ */
+
+ /* Patch AST2500/AST2510 */
+ if ((pdev->revision & 0xf0) == 0x40) {
+ if (!(vgacrd0 & AST_VRAM_INIT_STATUS_MASK))
+ ast_patch_ahb_2500(regs);
+ }
+
+ /* Double check that it's actually working */
+ data = __ast_read32(regs, 0xf004);
+ if ((data != 0xffffffff) && (data != 0x00)) {
+ config_mode = ast_use_p2a;
+
+ /* Read SCU7c (silicon revision register) */
+ __ast_write32(regs, 0xf004, 0x1e6e0000);
+ __ast_write32(regs, 0xf000, 0x1);
+ scu_rev = __ast_read32(regs, 0x1207c);
+ }
+ }
+ }
+
+ switch (config_mode) {
+ case ast_use_defaults:
+ dev_info(dev, "Using default configuration\n");
+ break;
+ case ast_use_dt:
+ dev_info(dev, "Using device-tree for configuration\n");
+ break;
+ case ast_use_p2a:
+ dev_info(dev, "Using P2A bridge for configuration\n");
+ break;
+ }
+
+ /*
+ * Identify chipset
+ */
+
+ if (pdev->revision >= 0x50) {
+ chip = AST2600;
+ dev_info(dev, "AST 2600 detected\n");
+ } else if (pdev->revision >= 0x40) {
+ switch (scu_rev & 0x300) {
+ case 0x0100:
+ chip = AST2510;
+ dev_info(dev, "AST 2510 detected\n");
+ break;
+ default:
+ chip = AST2500;
+ dev_info(dev, "AST 2500 detected\n");
+ break;
+ }
+ } else if (pdev->revision >= 0x30) {
+ switch (scu_rev & 0x300) {
+ case 0x0100:
+ chip = AST1400;
+ dev_info(dev, "AST 1400 detected\n");
+ break;
+ default:
+ chip = AST2400;
+ dev_info(dev, "AST 2400 detected\n");
+ break;
+ }
+ } else if (pdev->revision >= 0x20) {
+ switch (scu_rev & 0x300) {
+ case 0x0000:
+ chip = AST1300;
+ dev_info(dev, "AST 1300 detected\n");
+ break;
+ default:
+ chip = AST2300;
+ dev_info(dev, "AST 2300 detected\n");
+ break;
+ }
+ } else if (pdev->revision >= 0x10) {
+ switch (scu_rev & 0x0300) {
+ case 0x0200:
+ chip = AST1100;
+ dev_info(dev, "AST 1100 detected\n");
+ break;
+ case 0x0100:
+ chip = AST2200;
+ dev_info(dev, "AST 2200 detected\n");
+ break;
+ case 0x0000:
+ chip = AST2150;
+ dev_info(dev, "AST 2150 detected\n");
+ break;
+ default:
+ chip = AST2100;
+ dev_info(dev, "AST 2100 detected\n");
+ break;
+ }
+ } else {
+ chip = AST2000;
+ dev_info(dev, "AST 2000 detected\n");
+ }
+
+ *chip_out = chip;
+ *config_mode_out = config_mode;
+
+ return 0;
+}
+
static int ast_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
- struct ast_device *ast;
- struct drm_device *dev;
+ struct device *dev = &pdev->dev;
int ret;
+ void __iomem *regs;
+ void __iomem *ioregs;
+ enum ast_config_mode config_mode;
+ enum ast_chip chip;
+ struct drm_device *drm;
+ bool need_post = false;
ret = drm_aperture_remove_conflicting_pci_framebuffers(pdev, &ast_driver);
if (ret)
if (ret)
return ret;
- ast = ast_device_create(&ast_driver, pdev, ent->driver_data);
- if (IS_ERR(ast))
- return PTR_ERR(ast);
- dev = &ast->base;
+ regs = pcim_iomap(pdev, 1, 0);
+ if (!regs)
+ return -EIO;
+
+ if (pdev->revision >= 0x40) {
+ /*
+ * On AST2500 and later models, MMIO is enabled by
+ * default. Adopt it to be compatible with ARM.
+ */
+ resource_size_t len = pci_resource_len(pdev, 1);
+
+ if (len < AST_IO_MM_OFFSET)
+ return -EIO;
+ if ((len - AST_IO_MM_OFFSET) < AST_IO_MM_LENGTH)
+ return -EIO;
+ ioregs = regs + AST_IO_MM_OFFSET;
+ } else if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
+ /*
+ * Map I/O registers if we have a PCI BAR for I/O.
+ */
+ resource_size_t len = pci_resource_len(pdev, 2);
+
+ if (len < AST_IO_MM_LENGTH)
+ return -EIO;
+ ioregs = pcim_iomap(pdev, 2, 0);
+ if (!ioregs)
+ return -EIO;
+ } else {
+ /*
+ * Anything else is best effort.
+ */
+ resource_size_t len = pci_resource_len(pdev, 1);
+
+ if (len < AST_IO_MM_OFFSET)
+ return -EIO;
+ if ((len - AST_IO_MM_OFFSET) < AST_IO_MM_LENGTH)
+ return -EIO;
+ ioregs = regs + AST_IO_MM_OFFSET;
+
+ dev_info(dev, "Platform has no I/O space, using MMIO\n");
+ }
+
+ if (!ast_is_vga_enabled(ioregs)) {
+ dev_info(dev, "VGA not enabled on entry, requesting chip POST\n");
+ need_post = true;
+ }
+
+ /*
+ * If VGA isn't enabled, we need to enable now or subsequent
+ * access to the scratch registers will fail.
+ */
+ if (need_post)
+ ast_enable_vga(ioregs);
+ /* Enable extended register access */
+ ast_open_key(ioregs);
+
+ ret = ast_enable_mmio(dev, ioregs);
+ if (ret)
+ return ret;
+
+ ret = ast_detect_chip(pdev, regs, ioregs, &chip, &config_mode);
+ if (ret)
+ return ret;
+
+ drm = ast_device_create(pdev, &ast_driver, chip, config_mode, regs, ioregs, need_post);
+ if (IS_ERR(drm))
+ return PTR_ERR(drm);
+ pci_set_drvdata(pdev, drm);
- ret = drm_dev_register(dev, ent->driver_data);
+ ret = drm_dev_register(drm, ent->driver_data);
if (ret)
return ret;
- drm_fbdev_generic_setup(dev, 32);
+ drm_fbdev_generic_setup(drm, 32);
return 0;
}
return container_of(dev, struct ast_device, base);
}
-struct ast_device *ast_device_create(const struct drm_driver *drv,
- struct pci_dev *pdev,
- unsigned long flags);
+struct drm_device *ast_device_create(struct pci_dev *pdev,
+ const struct drm_driver *drv,
+ enum ast_chip chip,
+ enum ast_config_mode config_mode,
+ void __iomem *regs,
+ void __iomem *ioregs,
+ bool need_post);
static inline unsigned long __ast_gen(struct ast_device *ast)
{
#include "ast_drv.h"
-static bool ast_is_vga_enabled(void __iomem *ioregs)
-{
- u8 vgaer = __ast_read8(ioregs, AST_IO_VGAER);
-
- return vgaer & AST_IO_VGAER_VGA_ENABLE;
-}
-
-static void ast_enable_vga(void __iomem *ioregs)
-{
- __ast_write8(ioregs, AST_IO_VGAER, AST_IO_VGAER_VGA_ENABLE);
- __ast_write8(ioregs, AST_IO_VGAMR_W, AST_IO_VGAMR_IOSEL);
-}
-
-/*
- * Run this function as part of the HW device cleanup; not
- * when the DRM device gets released.
- */
-static void ast_enable_mmio_release(void *data)
-{
- void __iomem *ioregs = (void __force __iomem *)data;
-
- /* enable standard VGA decode */
- __ast_write8_i(ioregs, AST_IO_VGACRI, 0xa1, AST_IO_VGACRA1_MMIO_ENABLED);
-}
-
-static int ast_enable_mmio(struct device *dev, void __iomem *ioregs)
-{
- void *data = (void __force *)ioregs;
-
- __ast_write8_i(ioregs, AST_IO_VGACRI, 0xa1,
- AST_IO_VGACRA1_MMIO_ENABLED |
- AST_IO_VGACRA1_VGAIO_DISABLED);
-
- return devm_add_action_or_reset(dev, ast_enable_mmio_release, data);
-}
-
-static void ast_open_key(void __iomem *ioregs)
-{
- __ast_write8_i(ioregs, AST_IO_VGACRI, 0x80, AST_IO_VGACR80_PASSWORD);
-}
-
-static int ast_detect_chip(struct pci_dev *pdev,
- void __iomem *regs, void __iomem *ioregs,
- enum ast_chip *chip_out,
- enum ast_config_mode *config_mode_out)
-{
- struct device *dev = &pdev->dev;
- struct device_node *np = dev->of_node;
- enum ast_config_mode config_mode = ast_use_defaults;
- uint32_t scu_rev = 0xffffffff;
- enum ast_chip chip;
- u32 data;
- u8 vgacrd0, vgacrd1;
-
- /*
- * Find configuration mode and read SCU revision
- */
-
- /* Check if we have device-tree properties */
- if (np && !of_property_read_u32(np, "aspeed,scu-revision-id", &data)) {
- /* We do, disable P2A access */
- config_mode = ast_use_dt;
- scu_rev = data;
- } else if (pdev->device == PCI_CHIP_AST2000) { // Not all families have a P2A bridge
- /*
- * The BMC will set SCU 0x40 D[12] to 1 if the P2 bridge
- * is disabled. We force using P2A if VGA only mode bit
- * is set D[7]
- */
- vgacrd0 = __ast_read8_i(ioregs, AST_IO_VGACRI, 0xd0);
- vgacrd1 = __ast_read8_i(ioregs, AST_IO_VGACRI, 0xd1);
- if (!(vgacrd0 & 0x80) || !(vgacrd1 & 0x10)) {
-
- /*
- * We have a P2A bridge and it is enabled.
- */
-
- /* Patch AST2500/AST2510 */
- if ((pdev->revision & 0xf0) == 0x40) {
- if (!(vgacrd0 & AST_VRAM_INIT_STATUS_MASK))
- ast_patch_ahb_2500(regs);
- }
-
- /* Double check that it's actually working */
- data = __ast_read32(regs, 0xf004);
- if ((data != 0xffffffff) && (data != 0x00)) {
- config_mode = ast_use_p2a;
-
- /* Read SCU7c (silicon revision register) */
- __ast_write32(regs, 0xf004, 0x1e6e0000);
- __ast_write32(regs, 0xf000, 0x1);
- scu_rev = __ast_read32(regs, 0x1207c);
- }
- }
- }
-
- switch (config_mode) {
- case ast_use_defaults:
- dev_info(dev, "Using default configuration\n");
- break;
- case ast_use_dt:
- dev_info(dev, "Using device-tree for configuration\n");
- break;
- case ast_use_p2a:
- dev_info(dev, "Using P2A bridge for configuration\n");
- break;
- }
-
- /*
- * Identify chipset
- */
-
- if (pdev->revision >= 0x50) {
- chip = AST2600;
- dev_info(dev, "AST 2600 detected\n");
- } else if (pdev->revision >= 0x40) {
- switch (scu_rev & 0x300) {
- case 0x0100:
- chip = AST2510;
- dev_info(dev, "AST 2510 detected\n");
- break;
- default:
- chip = AST2500;
- dev_info(dev, "AST 2500 detected\n");
- break;
- }
- } else if (pdev->revision >= 0x30) {
- switch (scu_rev & 0x300) {
- case 0x0100:
- chip = AST1400;
- dev_info(dev, "AST 1400 detected\n");
- break;
- default:
- chip = AST2400;
- dev_info(dev, "AST 2400 detected\n");
- break;
- }
- } else if (pdev->revision >= 0x20) {
- switch (scu_rev & 0x300) {
- case 0x0000:
- chip = AST1300;
- dev_info(dev, "AST 1300 detected\n");
- break;
- default:
- chip = AST2300;
- dev_info(dev, "AST 2300 detected\n");
- break;
- }
- } else if (pdev->revision >= 0x10) {
- switch (scu_rev & 0x0300) {
- case 0x0200:
- chip = AST1100;
- dev_info(dev, "AST 1100 detected\n");
- break;
- case 0x0100:
- chip = AST2200;
- dev_info(dev, "AST 2200 detected\n");
- break;
- case 0x0000:
- chip = AST2150;
- dev_info(dev, "AST 2150 detected\n");
- break;
- default:
- chip = AST2100;
- dev_info(dev, "AST 2100 detected\n");
- break;
- }
- } else {
- chip = AST2000;
- dev_info(dev, "AST 2000 detected\n");
- }
-
- *chip_out = chip;
- *config_mode_out = config_mode;
-
- return 0;
-}
-
static void ast_detect_widescreen(struct ast_device *ast)
{
u8 jreg;
return 0;
}
-struct ast_device *ast_device_create(const struct drm_driver *drv,
- struct pci_dev *pdev,
- unsigned long flags)
+struct drm_device *ast_device_create(struct pci_dev *pdev,
+ const struct drm_driver *drv,
+ enum ast_chip chip,
+ enum ast_config_mode config_mode,
+ void __iomem *regs,
+ void __iomem *ioregs,
+ bool need_post)
{
struct drm_device *dev;
struct ast_device *ast;
- bool need_post = false;
- int ret = 0;
- void __iomem *regs;
- void __iomem *ioregs;
- enum ast_config_mode config_mode;
- enum ast_chip chip;
+ int ret;
ast = devm_drm_dev_alloc(&pdev->dev, drv, struct ast_device, base);
if (IS_ERR(ast))
- return ast;
+ return ERR_CAST(ast);
dev = &ast->base;
- pci_set_drvdata(pdev, dev);
-
- regs = pcim_iomap(pdev, 1, 0);
- if (!regs)
- return ERR_PTR(-EIO);
-
- if (pdev->revision >= 0x40) {
- /*
- * On AST2500 and later models, MMIO is enabled by
- * default. Adopt it to be compatible with ARM.
- */
- resource_size_t len = pci_resource_len(pdev, 1);
-
- if (len < AST_IO_MM_OFFSET)
- return ERR_PTR(-EIO);
- if ((len - AST_IO_MM_OFFSET) < AST_IO_MM_LENGTH)
- return ERR_PTR(-EIO);
- ioregs = regs + AST_IO_MM_OFFSET;
- } else if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
- /*
- * Map I/O registers if we have a PCI BAR for I/O.
- */
- resource_size_t len = pci_resource_len(pdev, 2);
-
- if (len < AST_IO_MM_LENGTH)
- return -EIO;
- ioregs = pcim_iomap(pdev, 2, 0);
- if (!ioregs)
- return ERR_PTR(-EIO);
- } else {
- /*
- * Anything else is best effort.
- */
- resource_size_t len = pci_resource_len(pdev, 1);
-
- if (len < AST_IO_MM_OFFSET)
- return ERR_PTR(-EIO);
- if ((len - AST_IO_MM_OFFSET) < AST_IO_MM_LENGTH)
- return ERR_PTR(-EIO);
- ioregs = regs + AST_IO_MM_OFFSET;
-
- drm_info(dev, "Platform has no I/O space, using MMIO\n");
- }
-
- ast->regs = regs;
- ast->ioregs = ioregs;
-
- if (!ast_is_vga_enabled(ioregs)) {
- drm_info(dev, "VGA not enabled on entry, requesting chip POST\n");
- need_post = true;
- }
-
- /*
- * If VGA isn't enabled, we need to enable now or subsequent
- * access to the scratch registers will fail.
- */
- if (need_post)
- ast_enable_vga(ioregs);
- /* Enable extended register access */
- ast_open_key(ioregs);
-
- ret = ast_enable_mmio(&pdev->dev, ioregs);
- if (ret)
- return ERR_PTR(ret);
-
- ret = ast_detect_chip(pdev, regs, ioregs, &chip, &config_mode);
- if (ret)
- return ERR_PTR(ret);
-
ast->chip = chip;
ast->config_mode = config_mode;
+ ast->regs = regs;
+ ast->ioregs = ioregs;
ast_detect_widescreen(ast);
ast_detect_tx_chip(ast, need_post);
if (ret)
return ERR_PTR(ret);
- return ast;
+ return dev;
}
projects / linux-block.git / commitdiff