mtd: gpmi-lib: Make checkpatch happy

Fix the following checkpatch warnings:

WARNING: line over 80 characters
#268: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:268:
+	* consecutive reboots. The latter case has not been seen on the MX23 yet,

WARNING: space prohibited before semicolon
#356: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:356:
+		(target.tRHOH_in_ns >= 0) ;

WARNING: space prohibited before semicolon
#1006: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:1006:
+		BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles)       ;

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
index aaced29727fb0437f6a0c142253b04cbc0ca82d0..c7a578c954fb95128376d63315be0edce4ace181 100644 (file)
--- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
+++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
@@ -265,8 +265,8 @@ int bch_set_geometry(struct gpmi_nand_data *this)
        * chip, otherwise it will lock up. So we skip resetting BCH on the MX23.
        * On the other hand, the MX28 needs the reset, because one case has been
        * seen where the BCH produced ECC errors constantly after 10000
-       * consecutive reboots. The latter case has not been seen on the MX23 yet,
-       * still we don't know if it could happen there as well.
+       * consecutive reboots. The latter case has not been seen on the MX23
+       * yet, still we don't know if it could happen there as well.
        */
        ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this));
        if (ret)
@@ -353,7 +353,7 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this,
        improved_timing_is_available =
                (target.tREA_in_ns  >= 0) &&
                (target.tRLOH_in_ns >= 0) &&
-               (target.tRHOH_in_ns >= 0) ;
+               (target.tRHOH_in_ns >= 0);
 
        /* Inspect the clock. */
        nfc->clock_frequency_in_hz = clk_get_rate(r->clock[0]);
@@ -1003,7 +1003,7 @@ void gpmi_begin(struct gpmi_nand_data *this)
        /* [1] Set HW_GPMI_TIMING0 */
        reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) |
                BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles)         |
-               BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles)       ;
+               BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles);
 
        writel(reg, gpmi_regs + HW_GPMI_TIMING0);