Required root node properties:
compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+Raspberry Pi Compute Module 3
+Required root node properties:
+compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+
+Raspberry Pi Compute Module 3 Lite
+Required root node properties:
+compatible = "raspberrypi,3-compute-module-lite", "brcm,bcm2837";
+
Raspberry Pi Zero
Required root node properties:
compatible = "raspberrypi,model-zero", "brcm,bcm2835";
"brcm,bcm6328-switch"
"brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
+Required properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg: a total of 3 register base addresses, the first one must be the
+ Switch Register Access block base, the second is the port 5/4 mux
+ configuration register and the third one is the SGMII configuration
+ and status register base address.
+
+ - interrupts: a total of 13 interrupts must be specified, in the following
+ order: port 0-5, 7-8 link status change, then the integrated PHY interrupt,
+ then the timestamping interrupt and the sleep timer interrupts for ports
+ 5,7,8.
+
+Optional properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg-names: a total of 3 names matching the 3 base register address, must
+ be in the following order:
+ "srab"
+ "mux_config"
+ "sgmii_config"
+
+ - interrupt-names: a total of 13 names matching the 13 interrupts specified
+ must be in the following order:
+ "link_state_p0"
+ "link_state_p1"
+ "link_state_p2"
+ "link_state_p3"
+ "link_state_p4"
+ "link_state_p5"
+ "link_state_p7"
+ "link_state_p8"
+ "phy"
+ "ts"
+ "imp_sleep_timer_p5"
+ "imp_sleep_timer_p7"
+ "imp_sleep_timer_p8"
+
See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
required and optional properties.
bcm2836-rpi-2-b.dtb \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
+ bcm2837-rpi-cm3-io3.dtb \
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \
reg = <0x33000 0x14>;
};
- qspi: qspi@27200 {
+ qspi: spi@27200 {
compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
reg = <0x027200 0x184>,
<0x027000 0x124>,
brcm,nand-has-wp;
};
- qspi: qspi@27200 {
+ qspi: spi@27200 {
compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
reg = <0x027200 0x184>,
<0x027000 0x124>,
srab: srab@36000 {
compatible = "brcm,nsp-srab";
- reg = <0x36000 0x1000>;
+ reg = <0x36000 0x1000>,
+ <0x3f308 0x8>,
+ <0x3f410 0xc>;
+ reg-names = "srab", "mux_config", "sgmii";
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "link_state_p0",
+ "link_state_p1",
+ "link_state_p2",
+ "link_state_p3",
+ "link_state_p4",
+ "link_state_p5",
+ "link_state_p7",
+ "link_state_p8",
+ "phy",
+ "ts",
+ "imp_sleep_timer_p5",
+ "imp_sleep_timer_p7",
+ "imp_sleep_timer_p8";
#address-cells = <1>;
#size-cells = <0>;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837-rpi-cm3.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+ model = "Raspberry Pi Compute Module 3 IO board V3.0";
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "GPIO0",
+ "GPIO1",
+ "GPIO2",
+ "GPIO3",
+ "GPIO4",
+ "GPIO5",
+ "GPIO6",
+ "GPIO7",
+ "GPIO8",
+ "GPIO9",
+ "GPIO10",
+ "GPIO11",
+ "GPIO12",
+ "GPIO13",
+ "GPIO14",
+ "GPIO15",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "GPIO32",
+ "GPIO33",
+ "GPIO34",
+ "GPIO35",
+ "GPIO36",
+ "GPIO37",
+ "GPIO38",
+ "GPIO39",
+ "GPIO40",
+ "GPIO41",
+ "GPIO42",
+ "GPIO43",
+ "GPIO44",
+ "GPIO45",
+ "GPIO46",
+ "GPIO47",
+ /* Used by eMMC */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+ hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+ memory {
+ reg = <0 0x40000000>;
+ };
+
+ reg_3v3: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "HDMI_HPD_N",
+ "EMMC_EN_N",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC";
+ status = "okay";
+ };
+};
+
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ bus-width = <4>;
+ vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_1v8>;
+ status = "okay";
+};
// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/net/microchip-lan78xx.h>
+
/ {
aliases {
ethernet0 = ðernet;
ethernet: ethernet@1 {
compatible = "usb424,7800";
reg = <1>;
+
+ mdio {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ eth_phy: ethernet-phy@1 {
+ reg = <1>;
+ microchip,led-modes = <
+ LAN78XX_LINK_1000_ACTIVITY
+ LAN78XX_LINK_10_100_ACTIVITY
+ >;
+ };
+ };
};
};
};
&spi_nor {
status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ boot@0 {
+ label = "boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ os-image@100000 {
+ label = "os-image";
+ reg = <0x040000 0x200000>;
+ compatible = "brcm,trx";
+ };
+
+ rootfs@240000 {
+ label = "rootfs";
+ reg = <0x240000 0xc00000>;
+ };
+
+ nvram@ff0000 {
+ label = "nvram";
+ reg = <0xff0000 0x010000>;
+ };
+ };
};
&usb2 {
&usb3_phy {
status = "okay";
};
+
+&nandcs {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ boot@0 {
+ label = "boot";
+ reg = <0x00000000 0x00080000>;
+ read-only;
+ };
+
+ nvram@80000 {
+ label = "nvram";
+ reg = <0x00080000 0x00180000>;
+ };
+
+ firmware@200000 {
+ label = "firmware";
+ reg = <0x00200000 0x07cc0000>;
+ compatible = "brcm,trx";
+ };
+
+ asus@7ec0000 {
+ label = "asus";
+ reg = <0x07ec0000 0x00140000>;
+ read-only;
+ };
+ };
+};
&spi_nor {
status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ boot@0 {
+ label = "boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ os-image@100000 {
+ label = "os-image";
+ reg = <0x040000 0x200000>;
+ compatible = "brcm,trx";
+ };
+
+ rootfs@240000 {
+ label = "rootfs";
+ reg = <0x240000 0xc00000>;
+ };
+
+ nvram@ff0000 {
+ label = "nvram";
+ reg = <0xff0000 0x010000>;
+ };
+ };
};
&usb3_phy {
reg = <0>;
#address-cells = <1>;
#size-cells = <1>;
+
+ partitions {
+ compatible = "brcm,bcm947xx-cfe-partitions";
+ };
};
};
};
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
- linux,part-probe = "ofpart", "bcm47xxpart";
status = "disabled";
+
+ partitions {
+ compatible = "brcm,bcm947xx-cfe-partitions";
+ };
};
};
open-source;
priority = <200>;
};
+
+ /* Hardware I2C block cannot do more than 63 bytes per transfer,
+ * which would prevent reading from a SFP's EEPROM (256 byte).
+ */
+ i2c1: i2c {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpioa 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpioa 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ };
+
+ sfp: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ mod-def0-gpios = <&gpioa 28 GPIO_ACTIVE_LOW>;
+ los-gpios = <&gpioa 24 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&gpioa 30 GPIO_ACTIVE_HIGH>;
+ tx-disable-gpios = <&gpioa 26 GPIO_ACTIVE_HIGH>;
+ };
};
&amac0 {
reg = <4>;
};
+ port@5 {
+ label = "sfp";
+ phy-mode = "sgmii";
+ reg = <5>;
+ sfp = <&sfp>;
+ managed = "in-band-status";
+ };
+
port@8 {
ethernet = <&amac2>;
label = "cpu";
projects / linux-2.6-block.git / commitdiff