- "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc
- reg : Offset and length of the register set for the device
- interrupts : Should contain CSPI/eCSPI interrupt
-- cs-gpios : Specifies the gpio pins to be used for chipselects.
- clocks : Clock specifiers for both ipg and per clocks.
- clock-names : Clock names should include both "ipg" and "per"
See the clock consumer binding,
Documentation/devicetree/bindings/clock/clock-bindings.txt
-- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
- Documentation/devicetree/bindings/dma/dma.txt
-- dma-names: DMA request names should include "tx" and "rx" if present.
-Obsolete properties:
-- fsl,spi-num-chipselects : Contains the number of the chipselect
+Recommended properties:
+- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip
+select lines can be used, they appear to always generate a pulse between each
+word of a transfer. Most use cases will require GPIO based chip selects to
+generate a valid transaction.
Optional properties:
+- num-cs : Number of total chip selects, see spi-bus.txt.
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+Documentation/devicetree/bindings/dma/dma.txt.
+- dma-names: DMA request names, if present, should include "tx" and "rx".
- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register
controlling the SPI_READY handling. Note that to enable the DRCTL consideration,
the SPI_READY mode-flag needs to be set too.
Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst).
+Obsolete properties:
+- fsl,spi-num-chipselects : Contains the number of the chipselect
+
Example:
ecspi@70010000 {
#define A3700_SPI_BYTE_LEN BIT(5)
#define A3700_SPI_CLK_PRESCALE BIT(0)
#define A3700_SPI_CLK_PRESCALE_MASK (0x1f)
+#define A3700_SPI_CLK_EVEN_OFFS (0x10)
#define A3700_SPI_WFIFO_THRS_BIT 28
#define A3700_SPI_RFIFO_THRS_BIT 24
prescale = DIV_ROUND_UP(clk_get_rate(a3700_spi->clk), speed_hz);
+ /* For prescaler values over 15, we can only set it by steps of 2.
+ * Starting from A3700_SPI_CLK_EVEN_OFFS, we set values from 0 up to
+ * 30. We only use this range from 16 to 30.
+ */
+ if (prescale > 15)
+ prescale = A3700_SPI_CLK_EVEN_OFFS + DIV_ROUND_UP(prescale, 2);
+
val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
val = val & ~A3700_SPI_CLK_PRESCALE_MASK;
pm_runtime_get_sync(&pdev->dev);
/* reset the hardware and block queue progress */
- spin_lock_irq(&as->lock);
if (as->use_dma) {
atmel_spi_stop_dma(master);
atmel_spi_release_dma(master);
}
+ spin_lock_irq(&as->lock);
spi_writel(as, CR, SPI_BIT(SWRST));
spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
spi_readl(as, SR);
/* Sets SPCMD */
rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0);
- /* Enables SPI function in master mode */
- rspi_write8(rspi, SPCR_SPE | SPCR_MSTR, RSPI_SPCR);
+ /* Sets RSPI mode */
+ rspi_write8(rspi, SPCR_MSTR, RSPI_SPCR);
return 0;
}
static int sun4i_spi_remove(struct platform_device *pdev)
{
- pm_runtime_disable(&pdev->dev);
+ pm_runtime_force_suspend(&pdev->dev);
return 0;
}
while (remaining_words) {
int n_words, tx_words, rx_words;
u32 sr;
+ int stalled;
n_words = min(remaining_words, xspi->buffer_size);
/* Read out all the data from the Rx FIFO */
rx_words = n_words;
+ stalled = 10;
while (rx_words) {
+ if (rx_words == n_words && !(stalled--) &&
+ !(sr & XSPI_SR_TX_EMPTY_MASK) &&
+ (sr & XSPI_SR_RX_EMPTY_MASK)) {
+ dev_err(&spi->dev,
+ "Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n");
+ xspi_init_hw(xspi);
+ return -EIO;
+ }
+
if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
xilinx_spi_rx(xspi);
rx_words--;
* for that name. This appears in the sysfs "modalias" attribute
* for driver coldplugging, and in uevents used for hotplugging
* @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when
- * when not using a GPIO line)
+ * not using a GPIO line)
*
* @statistics: statistics for the spi_device
*