serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.

Change hardware flow control code to adapt to both bf5xx and bf60x.
Disabled serial device before set termios for bf60x.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/tty/serial/bfin_uart.c b/drivers/tty/serial/bfin_uart.c
index 56b95b0447d941c7afc71682b1a45dfa9761b3ad..7924ba6d5dfb4802dcd4c0a30ac6a3424651c0ac 100644 (file)
--- a/drivers/tty/serial/bfin_uart.c
+++ b/drivers/tty/serial/bfin_uart.c
@@ -549,7 +549,7 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
 static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
 {
        struct bfin_serial_port *uart = dev_id;
-       unsigned short irqstat;
+       unsigned int irqstat;
        int x_pos, pos;
 
        spin_lock(&uart->rx_lock);
@@ -582,7 +582,7 @@ static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
 static unsigned int bfin_serial_tx_empty(struct uart_port *port)
 {
        struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-       unsigned short lsr;
+       unsigned int lsr;
 
        lsr = UART_GET_LSR(uart);
        if (lsr & TEMT)
@@ -741,7 +741,7 @@ static int bfin_serial_startup(struct uart_port *port)
                }
 
                /* CTS RTS PINs are negative assertive. */
-               UART_PUT_MCR(uart, ACTS);
+               UART_PUT_MCR(uart, UART_GET_MCR(uart) | ACTS);
                UART_SET_IER(uart, EDSSI);
        }
 #endif
@@ -799,7 +799,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
        struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
        unsigned long flags;
        unsigned int baud, quot;
-       unsigned short val, ier, lcr = 0;
+       unsigned int ier, lcr = 0;
 
        switch (termios->c_cflag & CSIZE) {
        case CS8:
@@ -871,6 +871,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
 
        /* Disable UART */
        ier = UART_GET_IER(uart);
+       UART_PUT_GCTL(uart, UART_GET_GCTL(uart) & ~UCEN);
        UART_DISABLE_INTS(uart);
 
        /* Set DLAB in LCR to Access CLK */
@@ -882,14 +883,11 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
        /* Clear DLAB in LCR to Access THR RBR IER */
        UART_CLEAR_DLAB(uart);
 
-       UART_PUT_LCR(uart, lcr);
+       UART_PUT_LCR(uart, (UART_GET_LCR(uart) & ~LCR_MASK) | lcr);
 
        /* Enable UART */
        UART_ENABLE_INTS(uart, ier);
-
-       val = UART_GET_GCTL(uart);
-       val |= UCEN;
-       UART_PUT_GCTL(uart, val);
+       UART_PUT_GCTL(uart, UART_GET_GCTL(uart) | UCEN);
 
        /* Port speed changed, update the per-port timeout. */
        uart_update_timeout(port, termios->c_cflag, baud);
@@ -949,7 +947,7 @@ bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
 static void bfin_serial_set_ldisc(struct uart_port *port, int ld)
 {
        struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-       unsigned short val;
+       unsigned int val;
 
        switch (ld) {
        case N_IRDA:
@@ -967,7 +965,7 @@ static void bfin_serial_set_ldisc(struct uart_port *port, int ld)
 static void bfin_serial_reset_irda(struct uart_port *port)
 {
        struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-       unsigned short val;
+       unsigned int val;
 
        val = UART_GET_GCTL(uart);
        val &= ~(UMOD_MASK | RPOLC);
@@ -1065,7 +1063,7 @@ static void __init
 bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
                           int *parity, int *bits)
 {
-       unsigned short status;
+       unsigned int status;
 
        status = UART_GET_IER(uart) & (ERBFI | ETBEI);
        if (status == (ERBFI | ETBEI)) {